WorldWideScience
1

Energy and cost analysis of organic fertilizer production in Nigeria  

Energy Technology Data Exchange (ETDEWEB)

Energy study was conducted in an organic fertilizer production plant in Nigeria, to determine the energy consumption patterns and the associated costs for the production of both powdered and pelletised fertilizer. Analysis was conducted for a daily production of 9000 kg of the finished products. Eight and nine defined unit operations were required for production of powder and pellets, respectively. The electrical and manual energy required for the production of powder were 94.5 and 5.6% of the total energy, respectively, with corresponding 93.9 and 5.1% for the production of pellets. The respective average energy intensities were estimated as 0.28 and 0.35 MJ/kg for powder and pellets. The most energy intensive operation was identified as the pulverizing unit with energy ...

2010-01-15

2

Data Sets for Data Group PEM - Mirador - NASA  

Science.gov (United States)

Nov 5, 2010 ... PEM. The Particle Environment Monitor measures the type, amount, energy, ... info, Daily PEM HEPS and MEPS data at the original sensor ...

3

Renewable energy forecasts for solar applications : an Environment Canada perspective  

Energy Technology Data Exchange (ETDEWEB)

The Meteorological Service of Canada has made weather datasets available in real-time on the Internet, for use by those with an interest in solar applications. Ensemble weather models can be used to produce medium range forecasts of weather events and to predict the likely available kilowatt-hours (kWhrs) of solar energy. As such, solar sites can maximize their harvest and use of solar energy. This presentation highlighted several different types of renewable energy forecasts obtained from weather models, including forecasts of expected kWhrs from solar panels and wind turbines, daily forecasts of expected solar heated water volumes and forecasts of water collection potential from impending precipitation events. The value of renewable energy forecasts in helping the solar energy sector monitor daily energy loads as well ...

2006-07-01

4

Experimental analysis of thermal performance of flat plate and evacuated tube solar collectors in stationary standard and daily conditions  

Science.gov (United States)

New comparative tests on two different types of solar collectors are presented in this paper. A standard glazed flat plate collector and an evacuated tube collector are installed in parallel and tested at the same working conditions; the evacuated collector is a direct flow through type with external compound parabolic concentrator (CPC) reflectors. Efficiency in steady-state and quasi-dynamic conditions is measured following the standard and it is compared with the input/output curves measured for the whole day. The first purpose of the present work is the comparison of results in steady-state and quasi-dynamic test methods both for flat plate and evacuated tube collectors. Besides this, the objective is to characterize and to compare the daily energy performance of these two types of collectors. An effective mean for describing and analyzing the daily performance is the so called input/output diagram, in which the ...

2010-08-15

5

Determination of selected microelements in polish herbs and their infusions  

Energy Technology Data Exchange (ETDEWEB)

Ba, Cd, Cr, Cu, Fe, Ni, Pb and Zn were determined in birch leaves (Folium Betulae), dandelion roots (Radix Taraxacae), hawthorn blossom (Inflorescentia Crataegi) and their infusions by graphite furnace atomic absorption spectrometry (GFAAS) after microwave digestion of plant samples. Infusions were made from herbs according to prescription for patients, provided by the producer of medicine on the package. The results obtained were compared with daily requirements for each element. Results show high content of cadmium in the medicinal plants analyzed. The highest level in infusions was observed for Ni and Zn (over 90% of the total element concentration for Ni and in most cases over 50% for Zn), and the lowest for Cd and Pb. The calculated daily intake of majority of the analyzed elements was very low (under 1% of daily requirements)

2007-08-01

6

Energy expenditures in four men estimated by D_2 "1"8O method at two times. II. From once daily samples of urine or breath  

International Nuclear Information System (INIS)

To make the doubly labelled water method for determining energy expenditure more applicable in a free-living population, collection of a single daily urine or breath sample would have advantages compared to a 24-hr urine collection. Coward et al. reported the use of a single daily urine sample. In the previously described study, a single urine collection and a fasting morning breath sample were collected from four men during two 21-day periods (fall, F, spring, S) while maintaining their body wts. on controlled diets (20% calories from protein, 40% from fat, 60% from CHO [F]; 20% protein, 20% fat, 60% CHO [S]). Urine and breath samples were analyzed to determine disappearance rates of D and "1"8O for up to 21 days. Values were compared with metabolizable energy intake levels (EI), with or without corrections for estimated changes in body composition assessed by several methods. Preliminary evaluations ...

1986-04-13

7

Can Markov regime-switching models improve power-price forecasts? Evidence from German daily power prices  

Energy Technology Data Exchange (ETDEWEB)

Non-linear autoregressive Markov regime-switching models are intuitive. Time-series approaches for the modelling of electricity spot prices are frequently proposed. In this paper, such models are compared with an ordinary linear autoregressive model with regard to their forecast performances. The study is carried out using German daily spot-prices from the European Energy Exchange in Leipzig. Four non-linear models are used for the forecast study. The results of the study suggest that Markov regime-switching models provide better forecasts than linear models. (author)

2006-09-15

8

Can Markov regime-switching models improve power-price forecasts? Evidence from German daily power prices  

International Nuclear Information System (INIS)

Non-linear autoregressive Markov regime-switching models are intuitive. Time-series approaches for the modelling of electricity spot prices are frequently proposed. In this paper, such models are compared with an ordinary linear autoregressive model with regard to their forecast performances. The study is carried out using German daily spot-prices from the European Energy Exchange in Leipzig. Four non-linear models are used for the forecast study. The results of the study suggest that Markov regime-switching models provide better forecasts than linear models. (author)

2006-09-01

9

Idaho 2008 Average Annual Daily Traffic  

Science.gov (United States)

Idaho Roads - 2008 Annual Average Daily Traffic (AADT)...

10

Folate fortification of rice by metabolic engineering  

British Library Electronic Table of Contents (United Kingdom)

Rice, the world's major staple crop, is a poor source of essential micronutrients, including folates (vitamin B9). We report folate biofortification of rice seeds achieved by overexpressing two Arabidopsis thaliana genes of the pterin and para-aminobenzoate branches of the folate biosynthetic pathway from a single locus. We obtained a maximal enhancement as high as 100 times above wild type, with 100 g of polished raw grains containing up to four times the adult daily folate requirement.

2007-01-01

11

Evapotranspiration estimation using the Landsat-5 Thematic Mapper image over the Gyungan watershed in Korea  

British Library Electronic Table of Contents (United Kingdom)

Even if there have been efforts to validate remote-sensing-based energy balance models, which provide evapotranspiration (ET) maps over a large spatial scale, few studies have been conducted to validate their performance in Korea. In this study, surface energy balance fluxes including ET were estimated and inter-compared with two different models using the Landsat-5 Thematic Mapper (TM) image over a watershed scale in Korea. While there were larger spatial discrepancies for net radiation, soil heat and sensible heat fluxes on a pixel-by-pixel basis between the two models, relatively smaller spatial discrepancies for the latent heat flux and daily ET were detected. The spatial discrepancies for the daily ET were larger in low topography and dense vegetation ranges. Despite the different par...

2011-01-01

12

Enamel-Calibrated Lamellar Bone Reveals Long Period Growth Rate Variability in Humans  

British Library Electronic Table of Contents (United Kingdom)

Abstract Mammalian teeth exhibit incremental structures representing successive forming fronts of enamel at varying time scales, including a short daily increment called a cross striation and a long period called a stria of Retzius, the latter of which, in humans, occurs on average every 8-9 days. The number of daily increments between striae is called the repeat interval, which is the same period as that required to form one increment of bone, i.e. the lamella, the fundamental - if not archetypal - unit of bone. Lamellae of known formation time nevertheless vary in width, and thus their measures provide time-calibrated growth rate variability. We measured growth rate variability for as many as 6 years of continuously forming primary incremental lamellar bone from midshaft femur histologic...

2011-01-01

13

Dietary and Nutritional Treatments for Attention-Deficit/Hyperactivity Disorder: Current Research Support and Recommendations for Practitioners  

British Library Electronic Table of Contents (United Kingdom)

Evidence for dietary/nutritional treatments of attention-deficit/hyperactivity disorder (ADHD) varies widely, from double-blind, placebo-controlled trials to anecdotal. In guiding patients, clinicians can apply the SECS versus RUDE rule: treatments that are Safe, Easy, Cheap, and Sensible (SECS) require less evidence than those that are Risky, Unrealistic, Difficult, or Expensive (RUDE). Two nutritional treatments appear worth general consideration: Recommended Daily Allowance/Reference Daily Intake multivitamin/mineral supplements as a pediatric health intervention not specific to ADHD and essential fatty acids, especially a mix of eicosapentaenoic acid, docosahexaenoic acid, and ?-linolenic acid as an ADHD-specific intervention. Controlled studies support the elimination of artificial fo...

2011-01-01

14

Combined inverse modeling approach and load duration curve method for variable nitrogen total maximum daily load development in an agricultural watershed  

British Library Electronic Table of Contents (United Kingdom)

Purpose Nonpoint sources (NPS) pollution has been an important cause for water quality impairment worldwide. To take the temporal variations of both NPS pollution and in-stream attenuation into consideration, an inverse modeling approach and the load duration curve (LDC) method were combined for variable nutrient total maximum daily load (TMDL) development. Methods Water quality and hydrological parameters were monitored monthly along the ChangLe River system in 2004?2008. The catchment NPS export load (EL) and TMDL for total nitrogen (TN) were estimated by the inverse format of an existing stream nutrient transport equation. The LDC method was used to describe the variability of EL, TMDL, requiring load (RLR) and percent (the ratio between the RLR and the EL, RPR) reduction, and then to s...

2011-01-01

15

Acclimation of tree function and structure to climate change and implications to forest carbon and nutrient balances  

Energy Technology Data Exchange (ETDEWEB)

Before large-scale anthropogenetic emissions the environmental factors have been rather stable for thousands of years, varying yearly, seasonally and daily in rather regular manners around some mean values. In this century the emissions of CO{sub 2}, sulphur and nitrogen from society to atmosphere are changing both atmospheric and soil environment at rates not experienced before. The fluxes to soil affect the contents of plant available nutrients and solubility of toxic compounds in the forest soil. Additionally, the chemical state of soil environment is coupled to tree growth, litter production and nutrient uptake as well as to the activity of biological organisms in soil, which decompose litter and release nutrients from it. Trees have developed effective regulation systems to cope with the environment during the evolution. The resulting acclimations improve the functioning of the trees if the environmental factors remain within their range of variation during ...

1996-12-31

16

ALASKA OIL AND GAS EXPLORATION, DEVELOPMENT, AND PERMITTING PROJECT  

Energy Technology Data Exchange (ETDEWEB)

This is the second technical report, covering the period from April 1, 2003 through September 30, 2003. This project brings together three parts of the oil exploration, development, and permitting process to form the foundation for a more fully integrated information technology infrastructure for the State of Alaska. The geo-technical component is a shared effort between the State Department of Administration and the US Department of Energy. The Alaska Oil and Gas Conservation Commission is rapidly converting high volumes of paper documents and geo-technical information to formats suitable for search and retrieval over the Internet. The permitting component is under the lead of the DNR Office of Project Management and Permitting. A web-based system will enable the public and other review participants to track permit status, submit and view comments, and obtain important project information on-line. By automating several functions of the current manual process, ...

2003-11-19

17

Minerals and trace elements determination in diets by neutron activation analysis  

International Nuclear Information System (INIS)

In the present study 12 diets, each one consisting of a pool of seven day diets, composed by four meals: breakfast, lunch, dinner and snack, adequate in energy and macro nutrients according to the RDA (Recommended Daily Allowance) recommendations, were elaborated and offered to a group of 12 men (19-42 years). The diets were collected by duplicate portion technique and dried by two different processes: freeze drying and 60 deg C ventilated oven drying. In the total, 24 diets were analyzed. The content of some minerals and trace elements (Ca, Fe, Mg, Mn, Na, Se and Zn) were determined by Instrumental Neutron Activation Analysis. The validation of methodology was made by analysis of the reference materials Typical Diet (NIST SRM 1548"a), Orchard Leaves (NIST SRM 1541) and Peach Leaves (NIST SRM 1547). The results observed by two different drying processes used were statistically compared by test T of Student. It was possible to conclude that the ...

2002-08-11

18

Pumped-storage: peak generation or operating reserve  

Energy Technology Data Exchange (ETDEWEB)

The trade-off which must be established between the various functions of pumped-storage plants is examined. A compromise between supply security and economic planning can be found only by coordinated planning of pumped-storage units and thermal generation plants. A model used by Electricite de France (EDF) to ensure optimized daily planning of thermal and pumped-storage units is described. The model, called the DEMETER model, ensures the optimization of the daily planning of thermal and pumped-storage plants. The model iterates between two levels: coordination where the prices of the generated energy and the operating reserve are determined to adjust generation to load and keep a sufficient reserve; and decomposition where the schedule of each unit is optimized on the basis of the above prices and taking into account local constraints such as unavailability, and minimum shut down time. The role of EDF is to supply customers ...

1984-08-01

19

Three-dimensional modeling of heat transport in deep hydrothermal reservoirs  

British Library Electronic Table of Contents (United Kingdom)

The need for alternative energy increases steadily???especially due to the climate change and the limited availability of fossil fuels. Geothermal power uses the intrinsic heat which is stored in the accessible part of the Earth???s crust. Its importance among the renewable energy resources originates from the almost unlimited energy supply of the Earth and its independence from external influences such as seasonal or even daily climatic variability. Nevertheless, there are risks which have to be assessed. From a mathematical point of view there are four building blocks of the characterization of deep geothermal systems: seismic exploration, gravimetry, modeling transport processes, and modeling the stress field. In particular, local depletion poses a significant risk during the industrial...

2011-01-01

20

Simulation on energy use for mechanical ventilation and air-conditioning (MVAC) systems in train compartments  

Energy Technology Data Exchange (ETDEWEB)

Unlike the conventional automotive, modem railway trains are designed with non-openable windows; and a mechanical ventilation and air-conditioning (MVAC) system is installed in each train compartment for better indoor air quality as well as to provide a thermally comfortable environment. The ventilation rate is no doubt a critical element in the design of a MVAC system, especially in Hong Kong where the daily passenger load is extremely heavy. Earlier studies illustrated that carbon dioxide can be controlled at 1000 ppm by increasing the ventilation rate to 25.2 m{sup 3} h{sup -1}; however, it will also lead to an increase in energy consumption. In this paper, the electrical energy consumption at various ventilation rates was studied, and the cost of maintaining a low carbon dioxide level was estimated These provide solid information for the local railway companies to improve the air quality inside the train compartments. ...

2000-01-01

21

Optimal security-constrained power scheduling by Benders decomposition  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a Benders decomposition approach to determine the optimal day-ahead power scheduling in a pool-organized power system, taking into account dispatch, network and security constraints. The study model considers the daily market and the technical constraints resolution as two different and consecutive processes. The daily market is solved in a first stage subject to economical criteria exclusively and then, the constraints solution algorithm is applied to this initial dispatch through the redispatching method. The Benders partitioning algorithm is applied to this constraints solution process to obtain an optimal secure power scheduling. The constraints solution includes a full AC network and security model to incorporate voltages magnitudes as they are a critical factor in some real power systems. The algorithm determines the active power committed to each generator so as to minimize the energy redispatch ...

2007-05-15

22

Kootenai River Nutrient Dosing System and N-P Consumption: Year 2008.  

Science.gov (United States)

In early 2006 we designed and built low energy consumption, pump-operated system, for dosing of the liquid nutrient in the summer 2006 season. This operated successfully, and the system was used again during the 2007 and 2008 seasons for dosing. During the early winter period, 2008, laboratory tests were made of the liquid nutrient pump system, and it was noted that small amounts of air were being entrained on the suction side of the pump, during conditions when the inlet pressure was low. It was believed that this was the cause of diurnal fluctuations in the flow supplied, characteristic of the 2007 year flow data. Replacement of '0' rings on the inlet side of the pumps was the solution to this problem, and when tested in the field during the summer season, the flow supplied was found to be stable. A decision was made by the IKERT committee at the meeting of 20th to 21st May 2008 (held in Coeur d'Alene, Idaho) to use an injection flow ...

2009-02-19

23

Army energy plan. Technical report  

Science.gov (United States)

The Plan identifies the Army's organization, goals, objectives, and policies with respect to energy. It projects energy consumption and costs to the year 2000 and summarizes the programs required to support the long range goals. A summary of current and needed energy related legislation is included. (Author)

1978-02-24

24

Assessment of the sensitivity and prediction uncertainty of evaporation models applied to Nasser Lake, Egypt  

British Library Electronic Table of Contents (United Kingdom)

SummaryThis paper examines the sensitivity and uncertainty of evaporation estimates from Nasser Lake, south of Egypt using data collected at the floating station Raft, 2km upstream of the Aswan High Dam, and 12 evaporation models. Based on their approach the evaporation models were ranked in five classes, respectively the Bowen ratio energy budget (BREB) approach, three energy-aerodynamic based methods, a mass transfer method, two temperature and five solar radiation-temperature approaches. State dependent parameter models were used to estimate the sensitivity indices of the different evaporation estimation methods at daily and monthly frequencies. A drastic reduction in the cost of the sensitivity analysis was obtained when coupled with efficient sampling methods, producing quasi-Monte Ca...

2010-01-01

25

Traffic characterization of a residential wireless Internet access  

British Library Electronic Table of Contents (United Kingdom)

Traffic characterization is an important means for Internet Service Providers (ISPs) to adapt and to optimize their networks to the requirements of the customers. Most network measurements are performed in the backbone of these ISPs, showing both, residential and business Internet traffic. However, the traffic characteristics of business and home users differ significantly. Therefore, we have performed measurements of home users at a broadband wireless access service provider in order to reflect only home user traffic characteristics. In this paper, we present the results of these measurements, showing daily traffic fluctuations, flow statistics as well as application distributions. The results show a difference to backbone traffic characteristics. Furthermore, we observed a shift from web...

2011-01-01

26

Reliability of Speech Generating Devices: A 5-Year Review  

British Library Electronic Table of Contents (United Kingdom)

Individuals who use augmentative and alternative communication (AAC) depend on technology to meet their daily needs and form relationships. Speech generating devices (SGDs) are integral components of communication systems. Reliability of SGDs is critical for effective use in everyday life. This study examined the reliability of new SGDs and found that mean time to first failure was 42.7 (SD = 41.2) weeks and at least 40% required repairs within the first year of use. The components that most frequently broke down were touch screens, wiring, main boards, batteries, memory cards, and AC adaptors. The costs of repairing SGDs were analyzed. The clinical implications of device breakdown are identified for key stakeholders, including clients, families, service providers, funding agencies, and ma...

2009-01-01

27

Navy Occupational Health Information Management System (NOHIMS). System/Functional Manager's guide  

Energy Technology Data Exchange (ETDEWEB)

This guide is intended to provide the necessary guidance to successfully manage the NAVMED Navy Occupational Health Information Management System (NOHIMS) at NAVMED sites and the NAVSEA Occupational Safety and Health Record Keeping System (OSHRKS) at NAVSEA sites. Outlines procedures to manage system operations, procedures to resolve hardware, software and communications problems, and procedures outside the realm of system operations that are required for a successful system. This guide is intended for the System and Functional Managers use. The System Manager is the individual designated to provide overall ADP management to the entire local configuration. Usually responsible for file backup, daily operations of the CPU, security, supplies, equipment, operating software and technical ADP guidance to the local functional users.

1987-04-01

28

Dynamics of photosynthetic photon flux density (PPFD) and estimates in coastal northern California  

British Library Electronic Table of Contents (United Kingdom)

Plants require solar radiation for photosynthesis and their growth is directly related to the amount received, assuming that other environmental parameters are not limiting. Therefore, precise estimation of photosynthetically active radiation (PAR) is necessary to enhance overall accuracies of plant growth models. This study aimed to explore the PAR radiant flux in the San Francisco Bay Area of northern California. During the growing season (March through August) for 2?years 2007?2008, the on-site magnitudes of photosynthetic photon flux densities (PPFD) were investigated and then processed at both the hourly and daily time scales. Combined with global solar radiation (R S) and simulated extraterrestrial solar radiation, five PAR-related values were developed, i.e., flux density-based PAR ...

2011-01-01

29

Climatic changes in Central Italy and their potential effects on corn water consumption  

British Library Electronic Table of Contents (United Kingdom)

This study evaluates the trends of meteorological and agrometeorological indices computed at different sites in the Region of Umbria (Central Italy). The indices were selected on the basis of whether they enable the evaluation of the potential effects of climatic changes on agricultural water requirements and management. The meteorological stations were preliminarily selected considering the length and entirety of the data series and a homogeneous spatial coverage of the region under study. The daily rainfall and minimum and maximum temperature data collected at the stations were elaborated to calculate meteorological and agrometeorological indices (for corn, widespread irrigated crop in Central Italy).The results of the analysis show that rainfall has decreased generally everywhere and th...

2008-01-01

31

Alternative methods to determine headwater benefits  

Energy Technology Data Exchange (ETDEWEB)

In 1992, the Federal Energy Regulatory Commission (FERC) began using a Flow Duration Analysis (FDA) methodology to assess headwater benefits in river basins where use of the Headwater Benefits Energy Gains (HWBEG) model may not result in significant improvements in modeling accuracy. The purpose of this study is to validate the accuracy and appropriateness of the FDA method for determining energy gains in less complex basins. This report presents the results of Oak Ridge National Laboratory`s (ORNL`s) validation of the FDA method. The validation is based on a comparison of energy gains using the FDA method with energy gains calculated using the MWBEG model. Comparisons of energy gains are made on a daily and monthly basis for a complex river basin (the Alabama River Basin) and a basin that is considered relatively simple hydrologically (the ...

1997-11-10

32

Error ratio of daily clearness indexes estimated from phrase of general weather condition in various parts of Japan; Nippon kakuchi ni oite tenki gaikyo kara suiteishita seiten shisu no gosaritsu  

Energy Technology Data Exchange (ETDEWEB)

To utilize solar energy effectively, a method has been developed by which daily clearness indexes can be estimated from phrase of general weather condition, and it has been examined at four places located at different typical climatic divisions in Japan. Successive results of extra-terrestrial solar insulation and measured solar insulation were illustrated at each place. It was found that the envelope of maximal value among measured values is in proportion to the extra-terrestrial solar insulation. Based on the basic clearness index and the meaning of term expressing general weather condition defined by the Meteorological Agency, the general weather condition was quantitated using the clearness index. This value was defined as weather index. Relationship between the measured clearness index at each place and the weather index was analyzed regressively. Correlation between the both was highly close, proportionally. Accordingly, the clearness ...

1997-07-31

33

Drying characteristics and nitrogen loss of biogas digestate during drying process  

Energy Technology Data Exchange (ETDEWEB)

The cost of transporting biogas digestate can be decreased by reducing its water content. However, the digestate emits volatile compounds during drying. This study investigated the drying behaviour and the change of digestate composition. Drying took place in a hybrid solar/waste-heat dryer that used solar energy as well as waste heat from a combined heat and power unit (CHP) and the exhaust air of a microturbine. The experiment involved the use of 60 t of liquid digestate. Climatic conditions were measured inside and outside the drying hall. Dry matter (DM) and organic dry matter (ODM) were also measured on a daily basis. In addition, the energy consumption of waste and solar heat were recorded and related to the quantity of dried feedstock. The total nitrogen, ammonium, phosphate, potassium oxide, magnesium oxide and calcium oxide in the digestate were subjected to chemical analysis before and after the drying process. ...

2010-07-01

34

Winter indoor air quality, thermal comfort and acoustic performance of newly built secondary schools in England  

Energy Technology Data Exchange (ETDEWEB)

Previous studies have found that classrooms are often inadequately ventilated, with the resultant increased risk of negative impacts on the pupils. This paper describes a series of field measurements that investigated the indoor air quality, thermal comfort and acoustic performance of nine recently built secondary schools in England. The most significant conclusion is that the complex interaction between ventilation, thermal comfort and acoustics presents considerable challenges for designers. The study showed that while the acoustic standards are demanding it was possible to achieve natural ventilation designs that met the criteria for indoor ambient noise levels when external noise levels were not excessive. Most classrooms in the sample met the requirement of limiting the daily average CO{sub 2} concentration to below 1500 ppm but just a few met the need to readily provide 8 l/s per person of fresh air under the easy control of the ...

2009-07-15

35

Efficient Phagocytosis Requires Triacylglycerol Hydrolysis by Adipose Triglyceride Lipase*  

UK PubMed Central (United Kingdom)

Macrophage phagocytosis is an essential biological process in host defense and requires large amounts of energy. To date, glucose is believed to represent the prime substrate for ATP production in macrophages....Full Text Available

2010-06-25

36

Biofuels: Report to Congress  

Science.gov (United States)

Section 204 of the Energy Independence and Security Act of 2007 (EISA 2007) requires EPA to assess and report to Congress on the impacts to date and likely future impacts of the increased use of biofuels as required by the Clean Air Act, section 211(0). Environmental issues (...

37

Integrated Risk Framework for Gigawatt-Scale Deployments of Renewable Energy: The U.S. Wind Energy Case; October 2009  

Energy Technology Data Exchange (ETDEWEB)

Assessing the potential environmental and human effects of deploying renewable energy on private and public lands, along our coasts, on the Outer Continental Shelf (OCS), and in the Great Lakes requires a new way of evaluating potential environmental and human impacts. The author argues that deployment of renewables requires a framework risk paradigm that underpins effective future siting decisions and public policies.

2010-04-01

38

Renewable energy technologies for irrigation water pumping in India: projected levels of dissemination, energy delivery and investment requirements using available diffusion models  

Energy Technology Data Exchange (ETDEWEB)

Using the past diffusion trends of four renewable energy technologies for irrigation water pumping in India (SPV pumps, windmill pumps and biogas/producer gas driven dual fuel engine pumps), results of an attempt to project their future dissemination levels, have been presented in this study. The likely contribution of the renewable energy options considered in the study to the projected energy demand for irrigation water pumping in India has been estimated. Estimates of the associated investment requirements taking into account the learning effect have also been presented. (author)

2005-12-01

39

The cooperative housing society Vaarst Vestervang - green building; Andelsboligforeningen Vaarst Vestervang - groent byggeri  

Energy Technology Data Exchange (ETDEWEB)

Vaarst Vestervang (Denmark) comprises 16 villas and 1 communal building. The complex was designed by the inhabitants themselves with the aim of polluting the environment as little as possible. The land area constitutes 69.000 square meters where it is possible to grass animals. The document reports a measuring programme concerning the overall heat consumption as one of the main aims of the inhabitants is to save energy and thus contribute to the protection of the environment. The capacity of the solar collectors predominantly used in the building complex was 235 kWh/m{sup 2}. Supplementary heating is provided by boilers fired with wood. The measuring system is described in detail. Tables show the influence of heat transmission losses, ventilation, airing out of rooms, the angle of the sun`s rays within the buildings and heating needs on energy consumption. Energy consumption data is presented in relation to the forms of ...

1993-10-01

40

Dynamic interactions and competing objectives in multifamily green building design  

Energy Technology Data Exchange (ETDEWEB)

This paper describes the challenges involved in the construction of a mid-rise housing development in Boston, Massachusetts, during which the development team elected to upgrade the initial design criteria from Minimum Building Code to Energy Star and Leadership in Energy and Environmental Design (LEED) certification. The various constraints imposed on the development were discussed, including constraints imposed by the involvement of substantial public funds as well as the constraints imposed by various funding sources that were approached to leverage energy efficiency and green building investment via competitive grant solicitations. Building owner and utility cost management priorities were outlined along with details of central mechanical system selection. Issues concerning isolation and compartmentalization were examined along with indoor pollution source control. A building load analysis was presented as well as ...

2005-07-01

41

Comparison of doubly labeled water, intake-balance, and direct- and indirect-calorimetry methods for measuring energy expenditure in adult men  

International Nuclear Information System (INIS)

Energy expenditure (EE) of four adult men on a weight-maintenance diet was estimated by use of doubly labeled water, intake balance, and direct and indirect calorimetry. The doubly labeled water (2H218O) method was used to estimate free-living EE for 13 d. Metabolizable energy (ME) intake was used to estimate free-living EE for 1 wk. The subjects' 24-h EE was measured in a dual direct-indirect room calorimeter on 3 alternate days. Estimates of free-living EE as measured by ME intake and doubly labeled water indicate agreement between the two methods (mean difference +/- SEM, -1.04 +/- 0.63%). Measurements of EE with indirect and direct calorimetry are equivalent (mean difference 0.63 +/- 0.44%). The daily EE measured by doubly labeled water in these free-living adults over a 13-d period was 15.01% greater than the 24-h EE measured within the calorimeter.

42

The development and validation of the daily electronic Endometriosis Pain and Bleeding Diary  

UK PubMed Central (United Kingdom)

BackgroundThe objective of this study was to develop and validate a daily electronic Endometriosis Pain and Bleeding Diary (EPBD) for assessing treatment-related changes in endometriosis...Full Text Available

43

The Relationships between Weather-Related Factors and Daily Outdoor Physical Activity Counts on an Urban Greenway  

UK PubMed Central (United Kingdom)

The purpose of this study was to examine relationships between weather and outdoor physical activity (PA). An online weather source was used to obtain daily max temperature [DMT], precipitation, and...Full Text Available

2011-02-01

44

Multiscale registration of planning CT and daily cone beam CT images for adaptive radiation therapy  

UK PubMed Central (United Kingdom)

Adaptive radiation therapy (ART) is the incorporation of daily images in the radiotherapy treatment process so that the treatment plan can be evaluated and modified to maximize the amount of radiation...Full Text Available

2009-01-01

45

Daily Spiritual Experiences in a Biracial, Community-based Population of Older Adults  

UK PubMed Central (United Kingdom)

ObjectivesThe objectives of this study were to describe the levels of daily spiritual experiences in community-dwelling older adults, to compare levels of spiritual...Full Text Available

2010-09-01

46

Comparative requirements for electric energy for production of hydrogen fuel and/or recharging of battery electric automobile fleets in New Zealand and the United States  

British Library Electronic Table of Contents (United Kingdom)

Within the current outlook for sustainable electric energy supply with concomitant reduction in emission of greenhouse gases, accelerated attention is focusing on the long-term development of hydrogen fuel cell and all-electric battery vehicles to provide alternative fuels to replace petroleum-derived fuels for automotive national fleets. The potential varies significantly between large industrially developed nations and smaller industrially developing nations. The requirement for additional electric energy supply from low-specific energy renewable resources and high-specific energy nuclear resources depends strongly on individual national economic, environmental, and political factors. Analysis of the additional electric energy supply required for the two potential large-scale technologie...

2010-01-01

47

Superconducting magnetic and inertial energy pulsed power systems  

International Nuclear Information System (INIS)

Superconducting magnetic and inertial energy pulsed power systems are being developed for future theta-pinch, Tokamak, and laser fusion applications. The short term requirements for these applications are discussed along with present day accomplishments. Areas requiring a research and development effort are examined in detail. Subjects discussed include stresses, energy loss factors, conductor metallurgy, cryogenic requirements, and electrical limitations of superconducting magnetic storage systems; costs, applications, and present technology of homopolar systems; and switching problems associated with both systems.

1975-07-15

49

Greening EPA | US EPA  

Science.gov (United States)

strives to reduce our "environmental footprint" in the following areas: EPA Facilities Energy Conservation Requirements | Goals and Strategies | Results | Reports Green Power...

2011-08-16

50

Design properties of coal liquids: edited workshop proceedings  

Science.gov (United States)

The advent of synfuels will require a large measurement and modeling effort of new thermodynamic and physical properties. These data are required for the economic design and operation of proposed synfuel plants. The areas of data need are well defined. The pace of measurement will be restricted by laboratory availability. The cost for the required data and for their correlation and modeling will be substantial. And finally, the cost of doing all this work will be substantial. The plants we are talking about are energy plants and synfuel plants. They are energy intensive plants, and as such, they offer the prospects for a great deal of energy saving. To do so requires good data. In those critical areas where we start hunting the energy hogs, we will find that with +-20% data those hogs are pretty well hidden.

1981-08-01

51

Bicarbonate kinetics and predicted energy expenditure in critically ill children2  

UK PubMed Central (United Kingdom)

Background:To determine nutrient requirements by the carbon oxidation techniques, it is necessary to know the fraction of carbon dioxide produced during the oxidative...Full Text Available

2008-08-01

52

Estimating energy requirement in cashew (Anacardium occidentale L.) nut processing operations  

Energy Technology Data Exchange (ETDEWEB)

This work deals with a study on estimation of energy consumption in eight readily defined unit operations of cashew nut processing. Data for analysis were collected from nine cashew nut mills stratified into small, medium and large categories to represent different mechanization levels. Series of equations were developed to easily compute requirements of electricity, fuel and labour for each of the unit operations. The computation of energy use was done using spreadsheet program on Microsoft Excel. The results of application test of the equations show that the total energy intensity in the cashew nut mills varied between 0.21 and 1.161MJ/kg. Electrical energy intensity varied between 0.0052 and 0.029MJ/kg, while thermal energy intensity varied from 0.085 to 1.064MJ/kg. The two identified energy intensive operations in cashew nut processing ...

2006-07-15

53

Local control and functional results after twice-daily radiotherapy for Ewing's sarcoma of the extremities  

International Nuclear Information System (INIS)

Purpose: Radiotherapy (RT) has been the predominant local treatment for Ewing's sarcoma of bone at the University of Florida. Twice-daily hyperfractionated RT was initiated in 1982 to improve local control and functional outcome. This retrospective review compares the results of once-daily vs. twice-daily RT in patients with primary Ewing's sarcoma of an extremity, with emphasis on functional outcome. Methods and Materials: Between June 1971 and January 1990, 37 patients were treated at the University of Florida for nonmetastatic Ewing's sarcoma of bone with a primary lesion in an extremity. Three patients underwent amputation. Of 34 patients treated with RT, 31 had RT alone and 3 had a combination of RT and local excision. Before 1982, 14 patients received once-daily RT; since 1982, 17 patients have received twice-daily RT. Doses of once-daily RT varied from 47 ...

1996-07-01

54

Potential of cattails as an energy source. Final report  

Energy Technology Data Exchange (ETDEWEB)

Research on the feasibility of growing cattails as an energy crop is described. The following topics are included: productivity in natural strands, germination requirements for seed, establishing stands by seeding, rhizome dormancy and development, harvesting and stand establishment, and analysis of canopy structure and radiation profiles in a natural community. (MHR)

1980-01-01

55

Ak-Chin Indian Community Biomass Feasiiblity Study  

Energy Technology Data Exchange (ETDEWEB)

Study of the conversion of chicken litter to biogas for the production of energy. There was an additional requirement that after extracting the energy from the chicken litter the nutrient value of the raw chicken litter had to be returned to the Ak-Chin Farms for use as fertilizer in a form and delivery method acceptable to the Farm.

2005-12-31

56

Wood residues in Alberta  

Energy Technology Data Exchange (ETDEWEB)

The forest products industry is the third largest economic sector in Alberta, producing pulp and paper, dimensional lumber, paneling, and value added products, providing some 40,000 jobs . 'Value added' is a key component of expanding economic activity within the forest products sector. Wood residues can play a key role in obtaining more value from forest resources by providing new products, serving as feedstock to energy and chemical production, and playing a role in agriculture and land reclamation. One of the principal roles of the Forest Products Development Branch of the Alberta Economics Department is to encourage the development of the industry by creating new uses for these materials and developing awareness of the scope of the resource. Distances to markets, economic competition from conventional energy sources and coordination of research efforts are substantial barriers to further development that the Forest ...

1999-07-01

57

Simple calculation of daily photosynthesis by means of five photosynthesis-light equations  

Energy Technology Data Exchange (ETDEWEB)

The performance of five well-known photosynthesis-light equations is compared by presenting a wide range of solutions in the form of dimensionless nomographs for the case where photosynthetically available radiation (PAR) reduces exponentially down the water column and is distributed sinusoidally through the photoperiod. These provide a simple means of calculating daily photosynthesis at any depth (e.g. at a benthic layer), or through a water column, avoiding the need to perform complex integrations. An examination is made of the accuracy of common approximate methods for calculating daily photosynthesis, assuming constant PAR. For optically deep water a modification is proposed to Talling's planimetric solution, to enable daily photosynthesis to be calculated more accurately, yet simply, over the whole range of possible PAR values. The errors induced by approximating the daily PAR distribution ...

1992-12-01

58

Policy development for solar water heaters: the case of Lebanon  

International Nuclear Information System (INIS)

Full text.The electric energy demand in Lebanon is estimated to grow at an average of 3-5% per year for the coming 10 years. Such an increase in energy demand is problematic for Lebanon since its economy is almost totally dependent on imported fuel which contributes to 97% of the overall energy requirements. Solar water heaters (SWH) are regarded as the most important element in a long term energy conservation and management strategy for this country, but their promotion is a national issue requiring the participation of many stake holders and decision makers. Additionally, the success of solar energy penetration into the existing energy market is constrained by many factors such as technical and financial limitations, decision criteria and policy instruments. This paper will explore the feasibility of SWH, and will work ...

2000-11-23

59

Building design using the energy nomographs  

Energy Technology Data Exchange (ETDEWEB)

Today's building industry is promoting the use of renewable sources of energy to heat, cool, and illuminate commercial buildings. Societies such as the International Solar Energy Society sponsor conferences such as this one to share knowledge and experience in the area of solar energy. However, the technologies presented here assume a need for heating, cooling or illumination. A simple technique is presented for determining the actual heating, cooling, and lighting requirements for commercial buildings, and for reducing those requirements through proper building design before applying solar technologies. The energy nomographs are a graphic energy design tool developed to aid designers in making cost effective decisions about energy alternatives early in the design process. Reducing loads at this point can help ...

1983-06-01

60

Methionine kinetics and balance at the 1985 FAO/WHO/UNU intake requirement in adult men studied with L-[2H3-methyl-1-13C]methionine as a tracer  

International Nuclear Information System (INIS)

The upper range of the requirement for methionine plus cystine in healthy adults was proposed in 1985 by FAO/WHO/UNU to be 13 mg.kg body wt-1.d-1. To explore the validity of this estimate, five healthy, young adult men were given for 7 d a diet based on an L-amino acid mixture supplying 13 mg methionine.kg-1.d-1 (87 mumol.kg-1.d-1) without cystine. Constant intravenous infusions of L-[2H3-methyl-1-13C]methionine were given on days 5 and 7 while subjects were in the fed and postabsorptive states, respectively. Estimates were made of methionine oxidation, and daily methionine balance was derived from the intake-oxidation data. For the five subjects, methionine balances were -0.9, +0.7, +3.5, -3.1, and -3.8 mg kg-1.d-1, or -6, +5, +23, -21, and -26 mumol.kg-1.d-1. These findings lead to the conclusion that the upper range of the requirement for methionine plus cystine probably exceeds 13 mg.kg-1.d-1 in healthy young adults. ...

61

Clinical study of p-aminobenzoic acid-N-xyloside Na in advanced cancer patients  

Energy Technology Data Exchange (ETDEWEB)

Therapeutic effect of p-aminobenzoic acid-N-xyloside Na (K-247) were studied. Eleven patients with a variety of solid tumors were treated with K-247 alone. K-247 was given orally 800 mg daily for 4 weeks. As for side effect of the drug, only mild gastritis was observed in a few patients. Partial response (over 25% reduction of tumor size) with a median duration of two months was observed in 3 patients. These cases were metastatic tumor of lung from the carcinoma of thyroid, metastatic tumors of lung from the carcinoma of kidney, and mediastinal tumor. In eight patients the response was classified as no change and in one patient there was progressive disease. Thus K-247 has some therapeutic activity in patients with solid tumor. Combination therapy of irradiation and administration of K-247 were also studied. In the twelve patients receiving the combination therapy, partial response was observed in 7 patients with complete response in 3 patients. In some patients it ...

1982-02-01

62

Black tide from the Bay of Campeche. [June 3, 1976 blowout  

Energy Technology Data Exchange (ETDEWEB)

The ruptured offshore oil well 80 miles from Mexican town of Ciudad del Carmen, which poured 8000 barrels of light oil a day into the Gulf of Mexico, provided marine scientists with the opportunity to monitor the spill and see what happens to petroleum hydrocarbons in sea water. Scientists followed changes in viscosity, surface tension, and buoyancy of individual oil globs as they moved through the water and interacted with the surface slick. Using gas chromatography and mass spectroscopy, chemists are gaining an understanding of the unique characteristics of the oil. Computer-generated models projected the slick's movement in the Gulf in response to wind and wave pressures, but the sophisticated system did not give an accurate daily prediction. Immediate damage to fish, turtles, and sea birds was documented by tagging. Long-term effects will take longer to ascertain since 25 years is generally required to flush oil out of sediments. ...

1980-01-24

63

Behavior of ice covers subjected to large daily flow and level fluctuations  

Energy Technology Data Exchange (ETDEWEB)

The stability of a solid ice cover subjected to rapidly varying water levels and discharge was investigated. The support from the bank limits the stress in the ice cover and consequently bank contact must be maintained to ensure ice cover stability. An analysis was required of the stability of ice hinges, a flexible connection between a solid ice cover and the riverbank. Phase II and phase III of the research involved a field study of the Peace River, investigating the evolution of ice hinges with water level variation, from initial ice cover cracking parallel to the banks, to a fully developed hinge. A test program of midwinter discharge variations was undertaken to gather specific data and measurements of ice hinge link length, ice thickness, hinge joint behavior, riverbank geometry, and response of ice hinging to water level variation. This volume of appendices to the study presents detailed observations and comments from field notes through the formation, ...

1984-11-01

64

Behavior of ice covers subjected to large daily flow and level fluctuations  

Energy Technology Data Exchange (ETDEWEB)

The stability of a solid ice cover subjected to rapidly varying water levels and discharge was investigated. The support from the bank limits the stress in the ice cover and consequently bank contact must be maintained to ensure ice cover stability. An analysis was required of the stability of ice hinges, a flexible connection between a solid ice cover and the riverbank. Phase II and phase III of the research involved a field study of the Peace River, investigating the evolution of ice hinges with water level variation, from initial ice cover cracking parallel to the banks, to a fully developed hinge. A test program of midwinter discharge variations was undertaken to gather specific data and measurements of ice hinge link length, ice thickness, hinge joint behavior, riverbank geometry, and response of ice hinging to water level variation. As a result of the program, concepts developed throughout the study were confirmed, preliminary guidelines for hydroelectric ...

1984-11-01

65

Design and performance of the solar-powered floor heating system in a green building  

Energy Technology Data Exchange (ETDEWEB)

In the green building of Shanghai Research Institute of Building Science, the evacuated tubular solar collectors with a total area of 150 m{sup 2} were installed to provide heating for the covered area of 460 m{sup 2}. The floor heating coil pipes were made of high-quality pure copper with the dimension of {phi} 12 x 0.7 mm. Under typical weather condition of Shanghai, the average heating capacity was 25.04 kW during the working hours from 9:00 to 17:00, which was sufficient to keep indoor thermal environment. The average electric COP of the floor heating system was 19.76 during the system operation. Compared with the widely used air-source heat pump heating systems with the electric COP of 3.5 in Shanghai, the solar-powered floor heating system shows great potential in energy conservation in winter. With respect to the whole heating period, the solar fraction was 56%. According to the performance analysis of the system with ambient parameters, it was observed that ...

2009-07-15

66

Ocean waves: energy resource assessment  

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to provide a general view of wave energy resource assessment. First, a review of the origin of waves and the transformation they undergo as they propagate towards the coast through waters of decreasing depth is presented. Following this, the wave and wave-energy parameters and the statistics required for resource characterization are described. The various types of wave data and their usefulness for the present purposes are summarised. A common methodology for assessment of the wave energy resource is developed. Finally, a general description of the global open ocean resource is presented.

2002-12-31

67

Government to buy low-cost energy from non-utility sources  

Energy Technology Data Exchange (ETDEWEB)

Power generated by manufacturers and third-party suppliers in venture capital projects is available to military and other government users at a cost 10 to 20% lower. Tax benefits and other financial incentives keep suppliers' costs low. Users are required to contract for a minimum amount of energy over a 20- to 30-year period. Military use of these energy projects includes sources based on solar energy, cogeneration, geothermal heat, and refuse-derived fuel. (DCK)

1983-04-04

68

Energy for Lebanon of tomorrow: paradigm of sustainable development and environment  

International Nuclear Information System (INIS)

An overview of the present status of energy sector in Lebanon and requirements of its future development is presented. The study is based on an economic analysis of needs and energy consumption among the population and on a comparison with other developing countries. Tables and graphs on energy distribution, needs and demands per habitant and national income are included. 3 figs. 3 tabs.

69

Pumped storage in the future power supply system  

Energy Technology Data Exchange (ETDEWEB)

Pumped storage plants (PSP) supply up to several GW of power and several ten GWh of capacity. Short start-up times and low start-up costs predestine PSP for the control energy market. Grid charges for PSP endanger the further integration of renewable energy and lead to higher electricity supply costs. Therefore, an amendment of legislation is urgently required. Requirements for building large PSP are met at numerous sites in the low mountain ranges of Germany. (orig.)

2010-07-01

70

Lithium question for nuclear fusion  

International Nuclear Information System (INIS)

An attempt is made to estimate the lithium reserve (the economically recoverable lithium) for the tritium breeding in D-T fusion reactors and other uses. Similar development patterns for fusion energy and fission energy are assumed to estimate the future lithium requirements. These requirements are grouped into three categories; the commercial uses, the lithium batteries for electric cars, and the fusion reactor uses. 5 refs.

71

Environmental restoration remedial action quality assurance requirements document  

International Nuclear Information System (INIS)

The environmental Restoration Remedial Action Quality Assurance Requirements Document (DOE/RL 90-28) defines the quality assurance program requirements for the US Department of Energy-Richland Field Office Environmental Restoration Remedial Action Program at the Hanford Site, Richland, Washington. This paper describes the objectives outlined in DOE/RL 90-28. The Environmental Restoration Remedial Action Program implements significant commitments made by the US Department of Energy in the Hanford Federal Facility Agreement and Consent Order entered into with the Washington State Department of Ecology and the US Environmental Protection Agency.

1991-09-08

72

Energetic analysis of fruit juice processing operations in Nigeria  

Energy Technology Data Exchange (ETDEWEB)

Energy and exergy studies were conducted in an orange juice manufacturing industry in Nigeria to determine the energy consumption pattern and methods of energy optimization in the company. An adaptation of the process analysis method of energy accounting was used to evaluate the energy requirement for each of the eight defined unit operations. The types of energy used in the manufacturing of orange juice were electrical, steam and manual with the respective proportions of 18.51%, 80.91% and 0.58% of the total energy. It was estimated that an average energy intensity of 1.12 MJ/kg was required for the manufacturing of orange juice. The most energy intensive operation was identified as the pasteurizer followed by packaging unit with energy ...

2008-01-15

73

Enterprise energy management : Part 1  

Energy Technology Data Exchange (ETDEWEB)

The needs of large industrial, commercial, and institutional energy consumers are more closely connected with the needs of power utilities and energy services companies, a result of the evolving global energy environment. Consumer choice, competition amongst energy suppliers, and increased demand are brought about in some regions by deregulation. Increasingly, large energy consumers expect high levels of quality and reliability from the energy delivered. As a result, management of the cost and the quality of the energy product and the energy assets that produce, deliver, control and consume it requires different strategies. Three major challenges must be overcome: (1) requirement to support economic and efficient delivery, purchasing and use of energy, (2) ...

2001-09-01

74

Carbon Capture and Water Emissions Treatment System (CCWESTRS) at Fossil-Fueled Electric Generating Plants  

Energy Technology Data Exchange (ETDEWEB)

The Tennessee Valley Authority (TVA), the Electric Power Research Institute (EPRI), and the Department of Energy-National Energy Technologies Laboratory (DOE-NETL) are evaluating and demonstrating integration of terrestrial carbon sequestration techniques at a coal-fired electric power plant through the use of Flue Gas Desulfurization (FGD) system gypsum as a soil amendment and mulch, and coal fly ash pond process water for periodic irrigation. From January to March 2002, the Project Team initiated the construction of a 40 ha Carbon Capture and Water Emissions Treatment System (CCWESTRS) near TVA's Paradise Fossil Plant on marginally reclaimed surface coal mine lands in Kentucky. The CCWESTRS is growing commercial grade trees and cover crops and is expected to sequester 1.5-2.0 MT/ha carbon per year over a 20-year period. The concept could be used to meet a portion of the timber industry's needs while simultaneously ...

2005-08-30

75

On the Utility of Antiprotons as Drivers for Inertial Confinement Fusion  

Energy Technology Data Exchange (ETDEWEB)

By contrast to the large mass, complexity and recirculating power of conventional drivers for inertial confinement fusion (ICF), antiproton annihilation offers a specific energy of 90MJ/{micro}g and thus a unique form of energy packaging and delivery. In principle, antiproton drivers could provide a profound reduction in system mass for advanced space propulsion by ICF. We examine the physics underlying the use of antiprotons ({bar p}) to drive various classes of high-yield ICF targets by the methods of volumetric ignition, hotspot ignition and fast ignition. The useable fraction of annihilation deposition energy is determined for both {bar p}-driven ablative compression and {bar p}-driven fast ignition, in association with 0-D and 1-D target burn models. Thereby, we deduce scaling laws for the number of injected antiprotons required per capsule, together with timing and focal spot ...

2003-10-20

76

Radiant{trademark} Liquid Radioisotope Intravascular Radiation Therapy System  

Energy Technology Data Exchange (ETDEWEB)

RADIANT{trademark} is manufactured by United States Surgical Corporation, Vascular Therapies Division, (formerly Progressive Angioplasty Systems). The system comprises a liquid {beta}-radiation source, a shielded isolation/transfer device (ISAT), modified over-the-wire or rapid exchange delivery balloons, and accessory kits. The liquid {beta}-source is Rhenium-188 in the form of sodium perrhenate (NaReO{sub 4}), Rhenium-188 is primarily a {beta}-emitter with a physical half-life of 17.0 hours. The maximum energy of the {beta}-particles is 2.1 MeV. The source is produced daily in the nuclear pharmacy hot lab by eluting a Tungsten-188/Rhenium-188 generator manufactured by Oak Ridge National Laboratory (ORNL). Using anion exchange columns and Millipore filters the effluent is concentrated to approximately 100 mCi/ml, calibrated, and loaded into the (ISAT) which is subsequently transported to the cardiac catheterization laboratory. The delivery ...

1998-01-16

77

Effects of Land Cover Change on Regional Atmospheric Chemistry and Climate in China. Interim Report  

Energy Technology Data Exchange (ETDEWEB)

The terrestrial biosphere can significantly affect the exchange of water and energy at the biosphere-atmosphere interface. Additionally, the land cover type can affect regional atmospheric chemistry and climate via biogenic volatile organic carbon (VOC) emissions and their formation of secondary organic aerosols. The broad goal of this study is to investigate the impact of land cover and vegetation changes on these specific chemistry and climate effects. The Common Land Model (CLM) is used to parameterize the biosphere-atmosphere interface over the Shanghai region in China. Phase 1 of this study, described in this report, generates input parameters for this model based on a time series of actual and derived parameters. Atmospheric forcing data are generated on an hourly temporal resolution based on a 20-year series of monthly and daily averages. Surface data, including land cover/land use and soil information, are generated for two scenarios: ...

2001-03-01

78

Security of energy supply under the laws of the European Union / European Community; Energieversorgungssicherheit im Recht der Europaeischen Union, Europaeischen Gemeinschaft  

Energy Technology Data Exchange (ETDEWEB)

Security of supply is defined as the availability and reliability of energy supply at acceptable prices. By security of energy supply we mean a globally large supply of reliable, affordable, clean energy. By virtue of its nature security of supply in the energy sector primarily requires making provisions for the future through exploration, innovation, research, diversification and investments in technology. Energy politics takes place in a tension field defined by the goals of economic efficiency, sustainability and security of supply. In the past there have been repeated shifts within this triad of goals. The task for a rational energy policy is to reconciliate these goals in a meaningful way. European energy policy is understood to comprise all sovereign measures taken by the European Union in the ...

2007-07-01

79

Use of fuel cells to meet military requirements for mobile power  

International Nuclear Information System (INIS)

'Full text:' The use of fuel cell technology in military applications will depend on safe, high energy density systems being developed. An important part of using this technology is also the development of alternative hydrogen producing fuels with high energy densities and are easy to transport. Fuel cells are now a very large R and D effort for several military applications around the world. The major reason is because of the high power demands needed requires electrical energy sources that far exceed the capabilities of batteries currently being fielded for portable applications. Fuel cells are regarded as highly efficient, tactical energy converters that can be adapted for wide range of power requirements. They are potentially the lowest weight power source when coupled with batteries or capacitors to form hybrid systems. Generally electrical power is needed ...

2004-09-25

80

Energy use in swine unit in the finishing system with waste treatment; Uso de energia em unidade suinicola em sistema de terminacao com tratamento de residuos  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study was to assess the energy flux and energetic balance related to the swine production and the recycling of residues generated by the system for utilization as organic fertilizers. The experiment was carried out at Vale dos Ipes Farm, located in the city of Ouro Verde do Oeste, in the Western of Parana State. One finishing phase swine unity containing 600 animals was monitored from January to June 2005. The treatment system is composed by one steel digester with capacity for 50 m{sup 3}, one sedimentation tank, one algae tank and one bio fertilizer storage tank. The swine barn cleaning is performed by dry scratching on a daily basis. The generated residues flow by gravitation through ducts towards the digester. The duration of the hydraulic retention period was 12 days. In the calculation of energetic efficiency, the energetic component ration is the greatest energetic cost in production system of finishing phase swine, ...

2006-07-01

81

Development of test procedures for benchmarking components in renewable energy systems applications, in particular energy storage systems  

Energy Technology Data Exchange (ETDEWEB)

Renewable energy systems (RES) are unique among energy supply systems because their performance and design depends entirely on the location and climatic conditions. As a result of design options, user requirements and local climatic conditions, there are enormous variations between RES. This paper describes a method how to evaluate the data on monitored renewable energy systems (RES) in such a way that the operating conditions and performance of individual components and the system as a whole can be analysed and compared. It shows how categories of similar use can be defined and recommendations for each category can be made to assist in the selection of the most suitable products. (orig.)

2004-07-01

82

Changes in Sea-Level Pressure over South Korea Associated with High-Speed Solar Wind Events  

CERN Document Server

We explore a possibility that the daily sea-level pressure (SLP) over South Korea responds to the high-speed solar wind event. This is of interest in two aspects: First, if there is a statistical association this can be another piece of evidence showing that various meteorological observables indeed respond to variations in the interplanetary environment. Second, this can be a very crucial observational constraint since most models proposed so far are expected to preferentially work in higher latitude regions than the low latitude region studied here. We have examined daily solar wind speed ${\\rm V}$, daily SLP difference ${\\rm \\Delta SLP}$, and daily ${\\rm \\log(BV^{2})}$ using the superposed epoch analysis in which the key date is set such that the daily solar wind speed exceeds 800 ${\\rm kms^{-1}}$. We find that the daily ${\\rm \\Delta SLP}$ averaged ...

2011-01-01

83

Energy-conscious air-side design: Phase 1 of energy use minimization  

Science.gov (United States)

Of the many energy-conservation options available to the design engineer, a system-management approach is recommended as one that will effect maximum benefits to the owner. Systems management includes energy-conscious consideration of design criteria, design details, installation, testing and balancing, and operation. It requires the informed participation of the design engineer, contractor, testing and balancing (TAB) engineer, and owner/operator. Within limits, almost every component of HVAC systems offers an opportunity to conserve energy. Many of these impact energy determinants such as system static pressure, system total air flow, or the quantity of outside air. A few design considerations for energy conservation in a simple system and the impact that the TAB work has on these are illustrated. Particular attention is devoted to the ...

1981-01-01

84

Energy requirements for rural development  

Energy Technology Data Exchange (ETDEWEB)

This study on the role of energy in the development of rural areas was originally conducted in the spring and summer of 1985. It was intended to serve as a background paper for the preparation of a program plan for the Office of Energy of the United States Agency for International Development. As such it begins with a brief overview of how rural development fits into national development, then offers a comprehensive framework for thinking about rural development in particular and the energy implications of the various components of rural development. Agriculture naturally comes to mind when rural areas are mentioned, but industry is an important component of rural activity as well. Consequently, both agricultural and nonagricultural energy use is discussed. Modernization of rural areas will change household, as well as production, energy use. However, household ...

1988-06-01

85

Solar-powered unmanned aerial vehicles  

Energy Technology Data Exchange (ETDEWEB)

An analysis was performed to determine the impact of various power system components and mission requirements on the size of solar-powered high altitude long endurance (HALE)-type aircraft. The HALE unmanned aerial vehicle (UAV) has good potential for use in many military and civil applications. The primary power system components considered in this study were photovoltaic (PV) modules for power generation and regenerative fuel cells for energy storage. The impact of relevant component performance on UAV size and capability were considered; including PV module efficiency and mass, power electronics efficiency, and fuel cell specific energy. Mission parameters such as time of year, flight altitude, flight latitude, and payload mass and power were also varied to determine impact on UAV size. The aircraft analysis method used determines the required aircraft wing aspect ratio, wing area, and total mass ...

1996-12-31

86

Environmental effects and energy efficiency in building design - a green building approach. Pt. 2. Basic data for environmental effects  

Energy Technology Data Exchange (ETDEWEB)

A research report presents the basic data required when designing a building with minimal environmental impacts. Topics covered include the energy consumption of building elements during their lifetime, the environmental implications linked to the extraction and processing of building material and the energy consumed in buildings by the occupants. (UK)

1993-12-31

87

Process energy management  

Energy Technology Data Exchange (ETDEWEB)

In many facilities, energy management is simply a matter of managing the energy required for lighting and space conditioning. In many others, however, energy management is much more complex and involves large motors and controls, industrial insulation, complex combustion monitoring, unique steam distribution problems, significant amounts of waste heat, etc. Typical facilities offering large energy management opportunities include industrial facilities, large office and commercial operations, government institutions such as schools, hospitals and prisons. Such facilities generally have specialized industrial, commercial or institutional processes that incorporate many of the concepts covered in other chapters. These processes require thorough analytical evaluations to determine the appropriate energy-saving measures. This chapter provides ...

1994-12-31

88

Review of Regulatory Quality Assurance Requirements for the Operation of Nuclear R and D Facilities  

International Nuclear Information System (INIS)

Korea Atomic Energy Research Institute (KAERI) has many R and D facilities in operation, including HANARO research reactor, radioactive waste treatment facility (RWTF), post-irradiation examination facility (PIEF) and irradiated material test facility (IMEF). Recently, nation-wide interest is focused on the safety and security of major industrial facilities. Safe operation of nuclear facilities is imperative because of the consequence of public disaster by radiological release/ contamination, in case of an accident. Recently, Ministry of Science and Technology (MOST) of the Korean government announced amendments of Atomic Energy laws to enforce requirements of the physical protection and radiological emergency. In this paper, the context of amended Atomic Energy laws were reviewed to confirm quality assurance measures and identify additional QA activities, if any, that is required ...

2005-10-27

89

Salivary cotinine concentrations in daily smokers in Barcelona, Spain: a cross-sectional study  

UK PubMed Central (United Kingdom)

BackgroundCharacterizing and comparing the determinant of cotinine concentrations in different populations should facilitate a better understanding of smoking patterns and addiction....Full Text Available

90

Premenstrual exacerbation of asthma.  

UK PubMed Central (United Kingdom)

Questionnaires and twice daily peak expiratory flow measurements were used to evaluate the effects of the menstrual cycle in asthmatic women. Forty per cent of women reported premenstrual deterioration...Full Text Available

1984-11-01

91

MODIFIED AMBIENT TEMPERATURE PERCEPTION AFFECTS DAILY ACTIVITY PATTERNS IN THE EUROPEAN GROUND SQUIRREL (SPERMOPHILUS ...  

Science.gov (United States)

... in full sun and in shade, using an infrared thermometer (MiniTemp Noncontact, Conrad Electronic, Nürnberg, Germany). Time intervals ... ...

92

Hispanic Cultural Influences on Medical Practice  

UK PubMed Central (United Kingdom)

Because the proportion of Hispanic patients is increasing rapidly, most physicians are now coming into daily contact with Hispanics. In addition to obvious difficulty with oral communication, Hispanics...Full Text Available

1983-10-01

93

Large scale rooftop photovoltaics grid connected system at Charoenphol-Rama I green building  

Energy Technology Data Exchange (ETDEWEB)

This paper presents a technical feasibility study project for the large scale rooftop photovoltaics (PV) grid connected system at Charoenphol-Rama I green building super store of TESCO LOTUS (TL) in Thailand. The objective of this project is (i) to study the technical feasibility of installation 350 kWp PV systems on the top of the roof in this site (ii) and to determine the energy produce from this system. The technical factors are examined using a computerized PVS 2000 simulation and assessment tool. This super store building located in Bangkok, with latitude 14 N, longitude 100 E and the building direction is 16 from North direction. The building roof area is 14,000 m2; with 3 degree face East and 3 degree face West pitch. Average daily solar energy in this area is approximately 5.0 kWh. The study team for this project consists of educational institution as School of Renewable Energy Technology ...

2004-07-01

94

Energy efficient soil disinfestation by microwaves  

Energy Technology Data Exchange (ETDEWEB)

A major obstacle prohibiting the use of microwaves for soil disinfection and disinfestation is the large amount of energy required to obtain sufficient results. The present work presents an experimental study of the effect of initial soil temperature and soil moisture on energy consumption by application of microwaves for soil disinfection. All experiments were carried out by using a microwave generator of a nominal power output of 900 W. The ultra-high-frequency field (2450{+-}2 MHZ) was produced by a magnetron tube and channelled through a metal waveguide. The output opening of the waveguide was placed directly on the soil surface. It was found that a soil with 15% moisture content (w.b.) and an initial temperature of 20degC requires energy to be heated at a depth of 10 cm up to 61degC which is 3.2 times more than the energy required to ...

2000-02-01

95

World energy: Building a sustainable future  

Energy Technology Data Exchange (ETDEWEB)

As the 20th century draws to a close, both individual countries and the world community face challenging problems related to the supply and use energy. These include local and regional environmental impacts, the prospect of global climate and sea level change associated with the greenhouse effect, and threats to international relations in connection with oil supply or nuclear proliferation. For developing countries, the financial cost of providing energy to provide basic needs and fuel economic development pose an additional burden. To assess the magnitude of future problems and the potential effectiveness of response strategies, it is important to understand how and why energy use has changed in the post and where it is heading. This requires study of the activities for which energy is used, and of how people and technology interact to provide the energy ...

1992-04-01

96

World energy: Building a sustainable future  

Energy Technology Data Exchange (ETDEWEB)

As the 20th century draws to a close, both individual countries and the world community face challenging problems related to the supply and use energy. These include local and regional environmental impacts, the prospect of global climate and sea level change associated with the greenhouse effect, and threats to international relations in connection with oil supply or nuclear proliferation. For developing countries, the financial cost of providing energy to provide basic needs and fuel economic development pose an additional burden. To assess the magnitude of future problems and the potential effectiveness of response strategies, it is important to understand how and why energy use has changed in the post and where it is heading. This requires study of the activities for which energy is used, and of how people and technology interact to provide the energy ...

1992-04-01

97

HVAC for energy showcase  

Energy Technology Data Exchange (ETDEWEB)

Southern California Gas Co.`s (SoCalGas) Energy Resource Center (ERC) in Downey, Calif. is a 45,000 ft{sup 2} (4,181 m{sup 21}) conference and education center created to help energy decision-makers find the most energy-efficient, cost-effective and environment-sensitive solutions to their energy requirements. The center has 36,000 ft{sup 2} (3,344 m{sup 2}) of remodeled space and 9,000 ft{sup 2} (836 m{sup 2}) of new space, all designed to showcase the latest energy-efficient and environment-sensitive technologies. The building is one of the 25 buildings in the US to be designated as Energy Star Showcase buildings by the US Environmental Protection Agency.

1997-07-01

98

Environmental Restoration Remedial Action quality assurance requirements document  

International Nuclear Information System (INIS)

This document defines the quality assurance requirements for the US Department of Energy-Richland Operations Office Environmental Restoration Remedial Action program at the Hanford Site. The Environmental Restoration Remedial Action program implements significant commitments made by the US Department of Energy in the Hanford Federal Facility Agreement and Consent Order entered into with the Washington State Department of Ecology and the US Environmental Protection Agency. This document combines quality assurance requirements from various source documents into one set of requirements for use by the US Department of Energy-Richland Operations Office and other Environmental Restoration Remedial Action program participants. This document will serve as the basis for developing Quality Assurance Program Plans and implementing procedures by the participants. The ...

99

PAS Domain of the Aer Redox Sensor Requires C-Terminal Residues for Native-Fold Formation and Flavin Adenine Dinucleotide Binding  

UK PubMed Central (United Kingdom)

The Aer protein in Escherichia coli is a membrane-bound, FAD-containing aerotaxis and energy sensor that putatively monitors the redox state of the electron transport system. Binding...Full Text Available

2004-10-01

100

NASA 2005 STTR Phase 1 Solicitation - NASA's SBIR & STTR Programs  

Science.gov (United States)

Advanced aerospace vehicles and system components tend to be slim and elastic, ...... In the manufacturing sector, semiconductor manufacturing requires ... The energy generation and storage for modern-day sensor networks, ...... Current NASA roadmaps point towards development of new hydrocarbon fueled engines. ...

101

Estimating production rates and operating costs of timber harvesting equipment in the northern Rockies. General technical report  

Energy Technology Data Exchange (ETDEWEB)

The report summarizes studies of ground, cable, and aerial logging systems in the Northern Rockies over a 15-year period. It provides nomographs and tables for calculating productivity and a system for comparing energy requirements.

1982-09-01

102

Conditioning of plastic wastes for thermal utilization; Aufbereitung von Kunststoffabfaellen zur thermischen Verwertung  

Energy Technology Data Exchange (ETDEWEB)

This article describes the processes for the treatment of plastic waste: sampling, sorting, comminution. The requirements for the different processes for waste treatment (as recycling, utilization as raw material, energy recovery, combustion) are listed. (SR)

1996-12-31

103

Combining fMRI with EEG and MEG in order to relate patterns of brain activity to cognition  

UK PubMed Central (United Kingdom)

The common factor that underlies several types of functional brain imaging is the electric current of masses of dendrites. The prodigious demands for the energy that is required to drive the...Full Text Available

2009-07-01

104

Hydrothermal industrialization electric-power systems development. Final report  

Energy Technology Data Exchange (ETDEWEB)

The nature of hydrothermal resources, their associated temperatures, geographic locations, and developable capacity are described. The parties involved in development, required activities and phases of development, regulatory and permitting requirements, environmental considerations, and time required to complete development activities ae examined in detail. These activities are put in proper perspective by detailing development costs. A profile of the geothermal industry is presented by detailing the participants and their operating characteristics. The current development status of geothermal energy in the US is detailed. The work on market penetration is summarized briefly. Detailed development information is presented for 56 high temperature sites. (MHR)

1982-03-01

105

Proliferation resistant fission energy systems  

Energy Technology Data Exchange (ETDEWEB)

Fission energy systems that significantly reduce the need for the user country to be involved in the nuclear operations and technology could simplify implementation and reduce the proliferation potential. Conceptual system designs with improved (relative to the once-through LWR fuel cycle) proliferation resistance for application in developing countries are being evaluated. The fission energy systems being studied include all activities and equipment necessary to produce energy, recycle selected materials, and dispose of the waste. The systems currently being studied are required to function with no refueling of the reactors on the user site. These requirements are being used to initiate the study, on the assumption that removal of these operations from within the developing countries will improve the proliferation resistance. Preliminary evaluations of a small fast reactor core ...

1997-07-02

106

Homoclinic chaos and energy condition violation  

International Nuclear Information System (INIS)

In this letter we discuss the connection between so-called homoclinic chaos and the violation of energy conditions in locally rotationally symmetric Bianchi type IX models, where the matter is assumed to be nontilted dust and a positive cosmological constant. We show that homoclinic chaos in these models is an artifact of unphysical assumptions: it requires that there exist solutions with positive matter energy density #rho#>0 that evolve through the singularity and beyond as solutions with negative matter energy density #rho#<0. Homoclinic chaos is absent when it is assumed that the dust particles always retain their positive mass. In addition, we discuss more general models: for solutions that are not locally rotationally symmetric we demonstrate that the construction of extensions through the singularity, which is required for homoclinic chaos, is not possible in general.

2006-09-15

107

Materials for power sources to meet military requirements  

Energy Technology Data Exchange (ETDEWEB)

Power source requirements for the military were presented to provide guidelines for research and development planning. Power sources that contain a high amount of energy and are small, light and durable are a common request from military users. Safety, reliability and low temperature performance are also important factors in the selection of power sources, as are cost and energy efficiency. Issues concerning advanced batteries were reviewed with reference to high energy density cathode materials. Various thermoelectric and renewable energy materials were discussed, with reference to recovery and conversion of waste heat. It was suggested that photovoltaic devices could help revolutionize military logistics by modifying energy re-supply requirements. Solid Oxide Fuel Cells (SOFC) were considered in relation to the high price of the ceramic ...

2005-07-01

108

High intensity lasers for gamma-gamma colliders  

International Nuclear Information System (INIS)

Compton backscattering of laser photons near the interaction point of an e"+e"- or e"-e"- collider can be used to produce a #gamma#-#gamma# or #gamma#-e"- collider. This paper describes the laser requirements, including pulse duration, intensity, energy, and wavelength, for such a collider. For most of the proposed, next generation, e"+e"- colliders, the laser wavelength should be in the near-infrared, with a pulse duration of 1 ps or less and an energy of similar 1 J per pulse. Current chirped pulse amplification laser systems in solid state lasing materials are well suited to meet these requirements. These systems are described. ((orig.)).

109

Evaluation of wastewater treatment requirements for thermochemical biomass liquefaction  

Science.gov (United States)

Biomass can provide a substantial energy source. Liquids are preferred for use as transportation fuels because of their high energy density and handling ease and safety. Liquid fuel production from biomass can be accomplished by any of several different processes including hydrolysis and fermentation of the carbohydrates to alcohol fuels, thermal gasification and synthesis of alcohol or hydrocarbon fuels, direct extraction of biologically produced hydrocarbons such as seed oils or algae lipids, or direct thermochemical conversion of the biomass to liquids and catalytic upgrading to hydrocarbon fuels. This report discusses direct thermochemical conversion to achieve biomass liquefaction and the requirements for wastewater treatment inherent in such processing. 21 refs.

1992-04-01

110

Determination of the initial energy in computerized tomography with proton beams; Determinacao da energia inicial em tomografia computadorizada com feixe de protons  

Energy Technology Data Exchange (ETDEWEB)

In earliest works devoted to proton computed tomography it was shown that the advantage of pCT image reconstruction appears when the energy is close to the Bragg peak region, since the proton passes the object. This effect provided by the Bragg peak makes the computerized tomography with protons possible. However, when decreasing the initial proton energy, with the increase of the irradiation dose, there are two effects that work simultaneously in opposite ways. First, the energy loss of a proton in an object becomes bigger at small initial energy. At the same time decreasing of the proton energy results in the increase of the energy straggling, requiring a larger number of protons. In this work the radiation dose dependence on the proton initial energy was studied using analytical formulas and computer simulations. The ...

2007-07-01

111

Regulatory quality assurance requirements for the operation of nuclear R and D facilities in Korea  

International Nuclear Information System (INIS)

Full text: Korea Atomic Energy Research Institute (KAERI) has many R and D facilities in operation. including HANARO research reactor, radioactive waste treatment facility (RWTF), post-irradiation examination facility (PIEF) and irradiated material test facility (IMEF). Recently. nation-wide interest is focused on the safety and security of major industrial facilities. Safe operation of nuclear facilities is imperative because of the consequence of public disaster by radiological release/contamination, in case of an accident. Recently, Ministry of Science and Technology (MOST) of the Korean government announced amendments of Atomic Energy laws to enforce requirements of the physical protection and radiological emergency. All provisions on nuclear safety regulation and radiation protection are entrusted to the Atomic Energy Act(AEA). The Act is enacted as the main law concerning the safety regulation of ...

2006-10-15

112

Sweet savings  

Energy Technology Data Exchange (ETDEWEB)

Ways of reducing the excessive energy consumption in the Polish sugar industry are examined. The three main areas where energy reduction measures might be taken are: reducing the process heat demand which arises from the need to evaporate excess water from the juice supplied to the crystallisers; improving the effectiveness of the thermal system by moving from the present four-effect evaporation to five-effect evaporation and using crystallisation vapours for juice heating; replacing old steam boilers with more efficient units. Most Polish sugar factories are relatively small, however, and the energy saving measures, all of which require the installation of more modern equipment, are not economically feasible in the short term. Moreover, the stringent limits on atmospheric emissions which come into effect in 1998 will require factories to use low-sulphur coal and install costly ...

1996-12-12

113

Keynote address. Division 1. Energy and economic development  

Energy Technology Data Exchange (ETDEWEB)

This paper was presented at the opening plenary session. As the end of the century approaches, environmental protection is one of the most significant global issues which will shape our energy path and economic development pattern. In face of environmental challenges, we will have to take into account environmental factors in the economic development process itself. This requires the pursuit of sustainable economic development, a process which may involve strengthened energy conservation, improved efficiency and switching to less carbon intensive energy sources. Energy inefficiency, technological scarcity and financial vulnerability in developing countries may best be resolved by changing their economic and market structures to facilitate relevant investments. However, effective reform of the energy industry in developing economies and economies in transition ...

1995-12-31

114

Biomass research program of the USDA Southern Agricultural Energy Center  

Energy Technology Data Exchange (ETDEWEB)

The biomass research program of the USDA, Southern Agricultural Energy Center is conducted at several locations throughout the United States. A portion of the research is directed toward improved systems to harvest, process and store biomass so that the energy density will be enhanced. Other research projects deal with: conversion and utilization of animal wastes in integrated energy-food production systems, including the production of liquid fuel and feed byproducts; producing low BTU gas to be utilized in internal combustion engines, including the system for continuous feeding of the gasifier; direct combustion of biomass for thermal energy; gasifying biomass so that the products of combustion can pass through a crop being dried without leaving deleterious residues; small scale systems for on-farm expelling of vegetable oil; and studies on the use of vegetable oils for diesel fuel substitutes. In ...

1982-08-01

115

Results from a Prototype Chicane-Based Energy Spectrometer for a Linear Collider  

Energy Technology Data Exchange (ETDEWEB)

The International Linear Collider (ILC) and other proposed high energy e{sup +}e{sup -} machines aim to measure with unprecedented precision Standard Model quantities and new, not yet discovered phenomena. One of the main requirements for achieving this goal is a measurement of the incident beam energy with an uncertainty close to 10{sup -4}. This article presents the analysis of data from a prototype energy spectrometer commissioned in 2006-2007 in SLAC's End Station A beamline. The prototype was a 4-magnet chicane equipped with beam position monitors measuring small changes of the beam orbit through the chicane at different beam energies. A single bunch energy resolution close to 5 {center_dot} 10{sup -4} was measured, which is satisfactory for most scenarios. We also report on the operational experience with the chicane-based spectrometer and suggest ...

2011-02-28

116

Executive summary of Energy Saving Opportunity Survey (ESOS) for Ft. McClellan Army Post, Anniston, Alabama  

Science.gov (United States)

In 1980 through 1982 a Basewide Energy Systems Plan (BESP) was developed under the direction of the Corps of Engineers at Ft. McClellan to assist the installation in meeting the requirements of the Army Facilities Energy Plan and the ten (10) year Energy Use Reduction Goal. Some of the energy saving projects recommended by the BESP have been implemented. In FY 1977, the total base energy consumption was 1,105,221 MBtu (Million British thermal units). By FY 1987, this had been reduced to 870,900 MBtu, a reduction of twenty-one percent (21%). This resulted in a cost avoidance for FY 1987 over base year FY 1977 of $2,960,986, or a thirty-two percent (32%) reduction.

1988-09-01

117

Energy savings opportunity survey. US Army Field Station Kunia, Oahu, Hawaii. Final report  

Science.gov (United States)

This Energy Savings Opportunity Survey (ESOS) is to identify Energy Conservation Opportunities (ECO`s) which are practical and economical for the reduction of energy consumption in accordance with the Army Facilities Energy Plan. The work to be performed under this project includes: (A) Coordinating with the on-going and proposed related projects. (B) Conducting a limited site survey required to identify applicable ECO`s and obtaining necessary data to evaluate the ECO`s. (C) Evaluating applicable ECO`s to determine their feasibility in accordance with current criteria. (D) Preparing programming and implementation documents for the recommended ECO`s. and (E) Preparing a comprehensive report to present the work performed including energy analysis, the results, and recommendations.

1989-06-01

118

Effects of population allocation of the electric power systems from the viewpoint of combined heat and power installation  

Energy Technology Data Exchange (ETDEWEB)

Recently it is strongly required to reduce energy consumption to cope with the global warming. Since energy consumption in commercial and residential sectors are increasing while industrial sector is almost constant in Japan, policies to lead energy conservation in urban areas is quite important. This study aims at investigating the performance of urban energy systems which install combined heat and power (CHP) as a district heating and cooling (DHC) plant and the influence of CHP on the structure of electric power systems of utilities. The behavior of energy technologies and the possibility of energy conservation are evaluated based on an optimization model with respect to total system cost. Sensitivity analysis of population allocation into urban areas indicates that fossil fuel consumption varies in the range of 10--20% compared with ...

1997-12-31

119

Decree of the Czechoslovak Atomic Energy Commission No. 436/1990 on quality assurance of selected facilities with respect to nuclear safety of nuclear facilities  

International Nuclear Information System (INIS)

The Decree specifies basic quality assurance requirements applicable to machines, their parts and materials, civil engineering structures, means for automated control of technological processes including hardware and software, and electricity supply systems related to nuclear safety of nuclear facilities, and stipulates binding procedures for the implementation of technical and organizational provisions associated with the quality of selected equipment to ensure nuclear safety of nuclear facilities. Safety classes are defined for selected equipment. Requirements laid on safety assurance documentation are specified, and requirements placed on safety assurance programmes, their preparation, finalization and approval are defined. Quality assurance requirements are also specified with respect to the designing, manufacture, construction, operation, repair, modification and decommissioning of nuclear ...

1995-02-01

120

Renewable energy technologies for federal facilities: Geothermal heat pump  

Energy Technology Data Exchange (ETDEWEB)

This sheet summarizes information on geothermal heat pumps (GHPs), which extracts heat from the ground in the winter and transfers heat to the ground in the summer. More than 200,000 GHPs are operating in US; they can reduce energy consumption and related emissions by 23 to 44% compared to air-source heat pumps. Opportunities for use of GHPs, requirements, and cost are described. Important terms are defined.

1996-05-01

121

Energy conservation by partial recirculation of peanut drying air  

Energy Technology Data Exchange (ETDEWEB)

Conventional, recirculating, and intermittent type peanut dryers were compared in a three-year study. Comparisons indicate that partial recirculation of peanut drying air may reduce energy consumption per unit of water removed by approximately 25% while also reducing required drying time and maintaining high quality.

1983-06-01

122

Clinical helical tomotherapy commissioning dosimetry  

International Nuclear Information System (INIS)

Helical tomotherapy presented many unique dosimetric challenges and solutions during the initial commissioning process, and some of them are presented. The dose calculation algorithm is convolution/superposition based. This requires that the energy fluence spectrum and magnitude be quantified. The methodology for doing so is described. Aspects of the energy fluence characterization that are unique to tomotherapy are highlighted. Many beam characteristics can be measured automatically by an included megavoltage computed tomography imaging system. This greatly improves data collection efficiency.

2003-12-01

123

Harvesting operations and energetics of tall grasses for biomass energy production: a case study  

Energy Technology Data Exchange (ETDEWEB)

Florida imports about 85% of its energy needs. Among the renewable energy sources available, biomass appears promising in Florida because of a favourable environment for production and the available methods to convert biomass to energy. Optimal production of biomass requires the identification and management of high yielding persistent perennial cultivars. Elephantgrass (Pennisetum purpureum Schum.) and energycane (Saccharum spontaneum L.) are two tall grasses that meet these requirements. To optimize the supply of convertible biomass, suitable methods of harvesting the crop must be available. The purpose of this research was to study the feasibility and energetics of harvesting, drying and baling tall grasses with conventional farm machinery. A Mathews rotary scythe and a New Holland 849 Auto Wrap large round baler were determined to provide a practical harvesting system for baled ...

1992-01-01

124

Thermal control of electric vehicle batteries  

Energy Technology Data Exchange (ETDEWEB)

The need to operate electric vehicles in warm, summer conditions and also provide for long periods of standby in cold climates is a challenging problem for any battery system. All advanced batteries of high specific energy require active cooling systems because adiabatic heating will raise the temperature to a level that is deleterious to cycle life. This cooling requires efficient paths for escape of heat to cooled surfaces; cooling the exterior of modules is insufficient. If a battery is heated by its own energy, and insulated to withstand exposure to a cold climate, only vacuum insulation will afford an appreciable reduction (>10{degrees}C) in the ambient temperature that can be tolerated. Standard insulations are of little use for this purpose because the heat loss rate causes too high a drain on the battery energy even for near-ambient temperature batteries.

1995-07-01

125

Status and progress in ion implantation technology for semiconductor device manufacturing  

International Nuclear Information System (INIS)

Rapid growth in implant applications in the fabrication of semiconductors has encouraged a dramatic increase in the range of energies, beam currents and ion species used. The challenges of a wider energy range, higher beam currents, continued reduction in contamination, improved angle integrity and larger substrates have motivated the development of many innovations. Advanced processes in submicron device production uses up to twenty implantation steps. Thus the outstanding growth of this industry has led to the evolution of a thriving business of hundreds of implantation equipment systems each year with very specific requirements. The present paper reviews the principal process requirements which resulted in the evolution of the equipment technology, and describes the recent trends in the ion implanter technology all three principal categories: high current, medium current and high ...

1998-12-08

126

On appraising alternative power plant investment proposals. Pt. 2: Application  

Energy Technology Data Exchange (ETDEWEB)

This paper is an application of the economic model developed in Part 1 and programmed in the computer code PEACES (program for the economic analysis of combined energy systems). A case study is presented in which hypothetical energy requirements at an industrial site are considered and an exercise is conducted wherein cogeneration is considered as a means of improving the energy situation at the site. Appropriate technologies that can satisfy the cogeneration requirements are investigated and technical and economic evaluations are carried out for a feasibility assessment. Of the three proposals considered, the gas turbine with heat recovery steam generator and the gas/steam turbine combined cycle cogeneration plant were found to be economically viable, while the steam turbine was not. It was recommended that the gas/steam turbine combined cycle cogeneration proposal be adopted, as ...

2000-12-01

127

Mulled coal: A beneficiated coal form for use as a fuel or fuel intermediate  

Energy Technology Data Exchange (ETDEWEB)

Energy International is developing a technology that will create a staged formulation with the first coal form (Mulled Coal) that can be stored, transported, and pumped. Just prior to combustion, the Mulled Coal (MC) would be modified to provide the properties needed for proper atomization. This concept is an alternative to the expensive and energy intensive thermal drying processing of fine coal wet cakes. The material is suitable for both direct feed use in conventional and fluid bed combustors as well as on-site conversion to combustible slurries. By maintaining the coal form relatively close to the feed wet cake, only minor processing with low additive levels and low energy blending needed at the point of production. Its conversion to slurry or other use-feed form is made near the time of use and thus the requirements for stability, climatic control, and other storage, transport, and handling ...

1991-10-01

128

The growth factor from plerocercoid larvae of the tapeworm, Spirometra mansonoides, stimulates growth but is not diabetogenic.  

Science.gov (United States)

A factor produced by plerocercoids of the tapeworm Spirometra mansonoides is similar to human growth hormone (hGH) in that it stimulates body growth, binds to hGH receptors, cross-reacts with anti-hGH antibodies, and has lactogenic and insulin-like activities. The purpose of this study was to determine whether plerocercoid growth factor (PGF) is similar to hGH in expressing diabetogenic activity in the genetically obese (ob/ob) mouse. To determine an effective dose for use in the obese mice, the ability of daily injections of PGF to stimulate growth of phenotypically normal mice of the same strain was assessed in a 10-day weight gain assay. Injections of PGF stimulated a dose-dependent weight gain (r = 0.83) and 25 ng eq/day of PGF stimulated a response not significantly different from that produced by 100 micrograms of bovine growth hormone/day. Diabetogenicity was assessed using fasting blood glucose and glucose tolerance tests in obese mice that had been ...

1989-06-01

129

The Protective Effect of Antioxidants on Oxidative Stress in Rats Exposed to the 950 MHz Electromagnetic Field  

International Nuclear Information System (INIS)

Studies have linked cell phone radiation to health problems such as headaches, high blood pressure, cancer and more. There is a latency period for most diseases and it may take years and more studies before the required weight of evidence is established. But the effects are cumulative and precautions should be taken now before it is too late. The aim of the present study was to investigate if supplementation with antioxidants would protect heart and liver tissues from harmful radiation emitted by cell phone. Thirty two male albino rats were randomly divided into four equal groups: I- Control, II- Antioxidants treated group, III- 950 MHz EMR, IV- 950 MHz EMR + antioxidants. A 950 MHz EMR radiation (217-Hz pulse rate, 2-W maximum peak power, SAR Specific Absorption Rate"1.6 W/Kg) was applied to groups III and IV 60 min/day, for 30 days using an experimental exposure device. Antioxidants supplement (Vitamins A, E and C + Se) was administered to rats ...

130

Research document no. 24. The integration of european electric markets: from the national markets juxtaposition to the establishment of a regional market; Cahier de recherche no. 24. L'integration des marches electriques europeens: de la juxtaposition de marches nationaux a l'etablissement d'un marche regional  

Energy Technology Data Exchange (ETDEWEB)

After the transcription of the electricity directive in national legislations, the European electricity market appears to be a vast set of juxtaposed markets which are weakly connected at the level of their wholesale contracts compartment. Referring to the technological peculiarities of electricity as a commodity, the paper identifies the direct conditions of regional integration of the electricity markets, those which would favour cross-border trade and allow to be near the normal functioning of a regional commodity market. The infrastructure network dependence and the need of a stringent technical coordination necessitate to unify the operation of the different systems and the rules of access, or at the least to come near this unification by strong coordination. A second major condition, which is not fully debated, is the increasing connexion of short-term markets, via daily physical trade and emergence of a European financial market, which could trade various ...

2000-11-01

131

Prediction of response of blood lead to airborne and dietary lead from volunteer experiments with lead isotopes  

Energy Technology Data Exchange (ETDEWEB)

To predict the response of blood lead to airborne and dietary lead requires knowledge of the rate of uptake of lead into the body from lung and gut, its subsequent partitioning between compartments, the stay time in those compartments, and its redistribution or excretion. Tracer studies with volunteers have shown no differences in systemic distribution of inorganic lead between tissues whether it is taken by inhalation, ingestion or injection. Lead is rapidly transferred from plasma to red cells, and there is slower movement thence into liver and other soft tissues, to bone, and to excreta. Work at Harwell and elsewhere with /sup 203/Pb has shown that the initial rapid distribution leaves rather over half the assimilated lead attached to red cells. The result is remarkably consistent, and applies also to dogs and baboons. The renal clearance (Vu) (ratio of U to CB, or daily urinary output expressed as mass of blood having the same lead ...

1985-04-22

132

Methionine kinetics in adult men: effects of dietary betaine on L-[2H3-methyl-1-13C]methionine  

International Nuclear Information System (INIS)

The effects of a daily 3-g supplement of betaine on kinetic aspects of L-[2H3-methyl-1-13C]methionine (MET) metabolism in healthy young adult men were explored. Four groups of four subjects each were given a control diet, based on an L-amino acid mixture supplying 29.5 and 21.9 mg.kg-1.d-1 of L-methionine and L-cystine for 4 d before the tracer study, conducted on day 5 during the fed state. Two groups received the control diet and two groups received the betaine supplement. Tracer was given intravenously (iv) or orally. The transmethylation rate of MET (TM), homocysteine remethylation (RM), and oxidation of methionine were estimated from plasma methionine labeling and 13C enrichment of expired air. RM tended to increase (P = 0.14) but the TM and methionine oxidation were significantly (P less than 0.05) higher after betaine supplementation when estimated with the oral tracer. No differences were detected with the intravenous tracer. Methionine concentration in ...

133

Construction of a genome-wide human BAC-Unigene resource. Final progress report, 1989--1996  

Energy Technology Data Exchange (ETDEWEB)

Currently, over 30,000 mapped STSs and 27,000 mapped Unigenes (non-redundant, unigene sets of cDNA representing EST clusters) are available for human alone. A total of 44,000 Unigene cDNA clones have been supplied by Research Genetics. Unigenes, or cDNAs are excellent resource for map building for two reasons. Firstly, they exist in two alternative forms -- as both sequence information for PCR primer pairs, and cDNA clones -- thus making library screening by colony hybridization as well as pooled library PCR possible. The authors have developed an efficient and robust procedure to screen genomic libraries with large number of DNA probes. Secondly, the linkage and order of expressed sequences, or genes are highly conserved among human, mouse and other mammalian species. Therefore, mapping with cDNA markers rather than random anonymous STSs will greatly facilitate comparative, evolutionary studies as well as physical map building. They have currently deconvoluted over 10,000 Unigene ...

1996-12-31

134

Addressing the Challenges Special Needs Students Face when Transitioning from the Classroom to the Workplace  

Science.gov (United States)

One of the biggest fears and challenges a parent of a child with special needs faces is navigating the post-22 landscape. When a child hits the age of 22, the Department of Elementary and Secondary Education (DESE) is no longer required to provide daily services and support. Whatever the abilities, or disabilities, of a child, every parent has the same concerns about how their child will productively fill their days and live as independently as possible without the safety net of the DESE. One of the transition paths most frequented is entering the workforce. Public and private schools alike work to teach their students the basic skills they need to work. In fact, the national Individuals with Disabilities Education Act (IDEA) states that students must have a transition plan in formulation by the age of 16. This article describes the vocational program developed by the League School of Greater Boston which specifically addresses the challenges ...

2010-10-01

135

A study of image-guided radiotherapy of bladder cancer based on lipiodol injection in the bladder wall  

Energy Technology Data Exchange (ETDEWEB)

Purpose. We have tested a procedure of focal injection of the contrast medium Lipiodol as a fiducial marker for image-guided boost of the tumor in bladder cancer radiotherapy (RT). In this study, we have evaluated the feasibility and the safety of the method as well as the inter- and intra-fraction shift of the bladder tumor. Materials and methods. Five patients with muscle invasive urinary bladder cancer were included in the study. Lipiodol was injected during flexible cystoscopy into the submucosa of the bladder wall at the periphery of the tumor or the post resection tumor-bed. Cone-beam CT (CBCT) scans were acquired daily throughout the course of RT. Results. Lipiodol demarcation of the bladder tumor was feasible and safe with only a minimum of side effects related to the procedure. The Lipiodol spots were visible on CT and CBCT scans for the duration of the RT course. More than half of all the treatment fractions required a geometric shift ...

2010-10-15

136

A pain management program for chronic cancer-treatment-related pain: a preliminary study.  

Science.gov (United States)

A large proportion of patients may develop chronic pain following cancer treatments such as surgery, radiotherapy, or chemotherapy. These patients can experience significant levels of physical and psychological morbidity. Our aim was to investigate a cognitive-behavioral pain management program (PMP) for cancer patients with chronic treatment-related pain. Thirteen patients (1 man, 12 women; mean age 52 yrs) completed the study, 9 of whom had a history of breast cancer and had received extensive medical treatment, including surgery. A combination of physical and psychological techniques were adapted from previous work in chronic benign pain and implemented by two therapists. Interventions included education, relaxation, exercise training, and goal setting. A variety of outcomes were examined to assess general fitness, psychological distress, coping success, activities of daily living, and pain report. The median number of interventions by each therapist was 10 (4 ...

2006-02-01

137

The most effective procurement mechanism for wind energy  

Energy Technology Data Exchange (ETDEWEB)

This presentation discussed common mechanisms for procuring wind energy in Canada. Mechanisms included renewable portfolio standards (RPSs); offsets; tax subsidies; financial subsidies; command and control mechanisms; and request for proposals (RFPs). A layered approach is required to avoid reliance on any single mechanism. RPSs require a certain minimum percentage of energy to come from renewable sources and aim to encourage the local development of renewable energy. RPSs are market-friendly and often result in the creation of tradable renewable energy credits (RECs) used for compliance purposes. RPSs work in parallel with cap and trade, baseline, and credit and carbon tax systems. RFPs target the lowest price offering, a practice which has often resulted in lower rates of return, high attrition, and a failure to attribute market prices to green attributes. It ...

2008-07-01

138

Optimization of advanced PMOS junctions using Ge, B and F co-implants  

International Nuclear Information System (INIS)

The main challenges for PMOS ultra shallow junction formation remain the transient enhanced diffusion (TED) and the solid solubility limit of boron in silicon. It has been demonstrated that low energy boron implantation and spike annealing are key in meeting the 90nm technology node ITRS requirements. To meet the 65nm technology requirements many studies have used fluorine co-implantation with boron and Si"+ or Ge"+ pre-amorphization (PAI) and spike annealing. Although using BF_2"+ can be attractive for its high throughput, self-amorphization and the presence of fluorine, many studies have shown that the fluorine successfully reduce TED, its energy needs to be well optimized with respect to the boron's, therefore BF_2"+ does not present the right fluorine/boron energy ratio for the optimum junction formation. In this work we optimize the fluorine energy for ...

2005-08-01

139

Photovoltaic mini power plants for integration in the third world and Eastern Europe. Market analysis aimed at health and education  

Energy Technology Data Exchange (ETDEWEB)

Energy is a critical factor which determines the progress of rural development. Energy is therefore an area of concern. The quality, availability and cost of conventional energies, plus the associated environmental effects are a growing problem - not only for the health infrastructure but also for agriculture and domestic life. This is true not only in developing countries where the fast growing industries and urban populations demand a soaring proportion of available energy at the expense of the rural communities, but also in the poorest countries with weak energy infrastructure. Renewable energies, much studied in the last 20 years, can meet the needs of rural health and education services and communities by providing high quality, low cost, non-polluting energy. Solar energy, in particular, has the flexibility to ...

1994-12-01

140

Final report for the DOE Suede Project, (solar utilization/economic development and employment project)  

Energy Technology Data Exchange (ETDEWEB)

The purpose of this solar energy project was to design, manufacture, install, maintain and evaluate solar heating systems in order to stimulate community acceptance of the practicality of solar applications, reduce non-renewable energy resource consumption, and decrease residential expenditures for energy. The project also provided skill training and experience for CETA employees in the design, manufacture, and installation of solar energy equipment systems. CDC's contract had four separate solar energy projects; namely: Domestic Water Heating Systems for four Single-Family Homes; Domestic Water Heating for an industrial building; Domestic Water Heating for a (4) unit apartment complex (includes (12) supplemental space heating units); and Integral Passive Water Heaters and Energy Conservation Devices for (8) one bedroom homes. CDC staff designed all ...

1983-10-19

141

Phantom dark energy with varying-mass dark matter particles: acceleration and cosmic coincidence problem  

CERN Document Server

We investigate several varying-mass dark-matter particle models in the framework of phantom cosmology. We examine whether there exist late-time cosmological solutions, corresponding to an accelerating universe and possessing dark energy and dark matter densities of the same order. Imposing exponential or power-law potentials and exponential or power-law mass dependence, we conclude that the coincidence problem cannot be solved or even alleviated. Thus, if dark energy is attributed to the phantom paradigm, varying-mass dark matter models cannot fulfill the basic requirement that led to their construction.

2009-01-01

142

Knowledge systems for management and modelling of energy systems  

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to survey the potential of knowledge systems for the management and modelling of energy systems. The paper starts with a short introduction to knowledge systems. The essence of knowledge systems is summarized and described in terms of modelling. Additionally the application of knowledge systems is compared with the use of conventional software on the one hand and human reasoning on the other. Next, research topics which are important in connection with technological applications of knowledge systems are reviewed. This paper follows with a review of knowledge system applications in the field of energy systems and ends with conclusions on the state of the art and required research and development.

1990-01-01

143

Geothermal applications for a tannery  

Energy Technology Data Exchange (ETDEWEB)

The tanning process and associated energy requirements are summarized. It appears that a significant economic impact may be possible if a shallow hydrothermal resource of approximately 150 to 170/sup 0/F (66 to 77/sup 0/C) were found, and the fluids were cascaded to produce the temperatures necessary for the various tanning operations. The hydrothermal energy would have to be cost competitive with the rapidly escalating fossil energy costs. Although one would need to thoroughly analyze the technical, environmental, and economic issues of such an application, this initial review indicates a good match between the process and potential hydrothermal resources.

1982-02-01

144

Energy conservation in the United Kingdom: a major industrial opportunity  

Energy Technology Data Exchange (ETDEWEB)

Energy conservation presents major opportunities to industry, both to improve its energy efficiency (hence its competitiveness and profitability) and to supply services and equipment. There are vast markets, both in the United Kingdom and overseas, but there are also barriers. There is reluctance on one hand to make new investment on the scale required. On the other hand, the problems of meeting a fragmented new demand are complicated by the fragmentation of the conservation supply industry. This calls for a new coherent, and innovative approach by both the conservation supply industry and the financial institutions. 3 tables.

1984-01-01

145

Analysis of beam emittance in FEL (Free Electron Laser)  

International Nuclear Information System (INIS)

To achieve high efficiency for the conversion of electron kinetic energy in an electron beam to electromagnetic energy in a Free Electron Laser (FEL), it is important to improve the beam quality. And hence, it is necessary to study and minimize the emittance growth of the beam. According to the requirements for the beam quality in an FEL, the author analyzed the emittance growth caused by the jump of the electric field in an accelerator, energy increase, wakefield in a waveguide, space charge effect and distribution of particles in a beam as well as the wakefield in a deflect system etc. The author also estimated the emittance change caused by the variation of the microwave field from the gun to the first accelerator for such case.

146

The development of fast breeder reactors  

International Nuclear Information System (INIS)

Modern civilisation is based on substantial utilisation of energy. Rapid industrial development and improvement of living standards in India require energy planners to adequately forecast the energy demand and take appropriate measures in advance. However, the development and establishment of new technology is a slow process, sometimes extending over decades. Hence, energy options based on new technologies need to be planned for much in advance making allowance for uncertainties and delays. Fast Breeder Reactor (FBR) technology is an advanced energy option promising abundant and economic supply of power. Research and development work on FBRs has been conducted at the Indira Gandhi Centre of Atomic Research (IGC) since 1971. The international trends in FBR development are highlighted in this discussion and an overview of some of the research activities at IGC is ...

147

Integrating protection and control systems for renewable energy systems  

Energy Technology Data Exchange (ETDEWEB)

Encouragement and incentives ar being given in many counties to the electricity industry and private sector to install, own and operate renewable energy systems. The impact of renewable energy installations connected to the grid or operating independently is an important issue concerning the technical and economic viability of harnessing these emerging energy sources. This paper brings out the need for developing and implementing a strategy for comprehensive and accurate protection and control systems for these dispersed generator installations. It appears that a combination of discrete and fuzzy logic devices on an integrated platform will be a novel technique for the protection and control schemes. This development has the potential to be cost effective and suits the requirements for operating renewable energy systems safety. (author). 2 figs., 16 refs.

1995-12-31

148

Innovation in sustainable energy in the Netherlands. Availability of capital and required government support  

Energy Technology Data Exchange (ETDEWEB)

To make the Dutch energy system more sustainable as formulated in the objectives of the recently constituted Task Force Energietransitie (Energy Transition), additional investments by the government in sustainable energy are needed. One of the ideas is to start a public-private risk bearing fund that invests in Netherlands based innovation projects in the area of sustainable energy. The ingoing assumption is that there is a shortage of capital supply for innovation projects that are in between the Research and Development phase and the market introduction phase, and that the government can attract further commercial private capital by co-investing itself. The Ministry of Economic Affairs has asked Bain and Company to perform a due diligence on the validity of the in-going assumptions for raising such a Venture Capital fund. This report contains the key conclusions of the study performed in June and the ...

2006-07-15

149

Energy threat to valuable land  

Energy Technology Data Exchange (ETDEWEB)

A negative public reaction is expected to oppose plans of the British energy industry to take valuable sites for industrial and commercial projects on the ground that government demand forecasts are too high and that they downplay conservation. The United Kingdom (UK) Department of Energy points out that public inquiry always accompanies energy installations and defends the projections made by producers even though each study emphasizes the demand for its own form of energy. At issue are plans to open 150 opencast coal mines a year to compensate for diminishing oil and gas supplies, onshore drilling by oil and gas exploration teams on nearly 50,000 km/sup 2/, and sites required for onshore pipelines, synthetic natural gas facilities, pumped storage plants, and nuclear power stations and waste management. The sites under discussion raise aesthetic and ecological concerns. (DCK)

1982-03-11

150

Energy and reserve dispatch in a multi-zone electricity market  

Energy Technology Data Exchange (ETDEWEB)

Competitive bidding for ancillary services (A/S), in addition to bidding for energy, is increasingly recognized as an important part of electricity markets. In this paper, an LP-based approach is presented for solving the multi-product (i.e. energy and A/S products), multi-zone/area physical market dispatch problem. The approach can explicitly represent various constraints, such as reserve requirement constraints, network security limits, and sharing of constrained resource capacity (e.g. maximum unit generation) between energy and reserve. The joint dispatch method, which dispatches energy and reserve market concurrently, is extended to allow inter-zonal reserve trading in multi-zone competitive pool. Numerical examples are included to demonstrate the salient characteristics of the joint dispatch solution.

1999-08-01

151

Energy use analysis of selected palm-kernel oil mills in south western Nigeria  

Energy Technology Data Exchange (ETDEWEB)

Energy use patterns and utilisation efficiencies in 40 factories producing palm kernel oil (PKO) in southwestern part of Nigeria were studied. The factories were stratified into small, medium and large scale categories based on the mode of operations and production capacities. Questionnaires were administered on the factories to obtain historical data on petrol, diesel and electricity consumption and PKO production outputs for seven years (1998-2004). Energy use efficiency indicators employed include: energy intensity (EI), energy cost per unit product (EC/P), energy ratio (ER), food energy ratio (FER) and percentage oil yield by weight. Results of the study indicated that averagely, 0.58, 0.53 and 0.74 GJ/10{sup 3} l of PKO were needed in the small, medium and large PKO factories, respectively. The average food energy ratios in the small, ...

2008-01-15

152

Soy isoflavones, diet and physical exercise modify serum cytokines in healthy obese postmenopausal women  

British Library Electronic Table of Contents (United Kingdom)

Objectives: Evaluate the effect of diet, physical exercise, and a daily oral intake of a soy isoflavones extract (Fisiogen) contained 200mg of Glycine max, which corresponded to 80mg of isoflavone (60.8mg of genistein, 16mg of daidzein and 3.2mg of glicitein) on leptin and other adipokines plasma levels in healthy obese postmenopausal women. Methods: A multicentric randomized longitudinal prospective cohort study was conducted in a sample of 87 healthy obese postmenopausal women. Patients were randomly assigned to a 1200kcal diet and exercise group (control group) or a group of 1200kcal diet, exercise, and daily oral intake of daily oral intake of a soy isoflavones extract (Fisiogen) contained 200mg of Glycine max, which corresponded to 80mg of isoflavone (60.8mg of genistein, 16mg of daid...

2011-01-01

153

Correspondence of interactive voice response (IVR) reports of nicotine withdrawal, craving, and negative mood with questionnaire ratings  

British Library Electronic Table of Contents (United Kingdom)

This study focuses on comparing reports of nicotine withdrawal, craving, and depressive symptoms obtained using an Interactive Voice Response (IVR) system and several questionnaires. As part of a smoking cessation trial, daily reports of withdrawal, craving, and negative mood were collected using an IVR system for 7 days after participants attempted to quit smoking, and several pencil and paper questionnaires (i.e., the Minnesota Nicotine Withdrawal Scale, the Questionnaire on Smoking Urges, and the Center for Epidemiological Studies-Depression) were completed a week after the target quit date. The sample was composed of 378 daily smokers. Moderate to high correlations were found between the research questionnaires obtained at the end of the week and the corresponding daily IVR reports of ...

2008-01-01

154

ALASKA OIL AND GAS EXPLORATION, DEVELOPMENT, AND PERMITTING PROJECT  

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to eliminate three closely inter-related barriers to oil production in Alaska through the use of a geographic information system (GIS) and other information technology strategies. These barriers involve identification of oil development potential from existing wells, planning projects to efficiently avoid conflicts with other interests, and gaining state approvals for exploration and development projects. Each barrier is the result of either current labor-intensive methods or poorly accessible information. This project brings together three parts of the oil exploration, development, and permitting process to form the foundation for a more fully integrated information technology infrastructure for the State of Alaska. This web-based system will enable the public and other review participants to track permit status, submit and view comments, and obtain important project information online. By automating several functions of the current manual process, ...

2003-08-04

155

Storage of electric energy gained from renewable sources  

Energy Technology Data Exchange (ETDEWEB)

This paper discussed issues related to the storage of electricity produced from renewable energy sources. Storage systems currently used by distribution systems were reviewed. The study showed that successful storage systems ensure high charging and discharging rates for shorter periods of time. Systems with high storage capacities must also be able to store energy for longer periods of time than traditional energy storage systems. Systems include pumped storage plants; electro-chemical accumulators; compressed air accumulators; and redox flow batteries. Hydrogen technologies for the storage of electric energy from renewable sources were reviewed. The paper also outlined energy storage and fuel cell research currently being conducted by researchers in the Czech Republic. The study concluded by stating that new energy storage technologies are ...

2009-03-11

156

Power plants 2010. Lectures  

International Nuclear Information System (INIS)

The proceedings include the following lectures: Facing the challenges - new structures for electricity production. Renewable energies in Europe - chances and challenges. Nuclear outlook in the UK. Sustainable energy for Europe. Requirements of the market and the grid operator at the electricity production companies. Perspectives for the future energy production. Pumped storage plants - status and perspectives. Nuclear power/renewable energies -partners or opponents? New fossil fired power stations in Europe - status and perspectives. Nuclear energy: outlook for new build and lifetime extension in Europe. Biomass in the future European energy market - experiences for dong energy. Meeting the EU 20:20 renewable energy targets: the offshore challenges. DESERTEC: sustainable electricity for Europe, ...

2010-09-22

157

Energy and exergy analyses of malt drink production in Nigeria  

Energy Technology Data Exchange (ETDEWEB)

Energy requirements and exergy inefficiencies for processing of malt drink were estimated for a Nigerian brewery. The process was divided into twenty-one basic unit operations and grouped into four main group operations: silo house, brew house, filter room and packaging house. The energy intensity for processing a batch of 9.8 tonnes brew grains to 562 hl of malt drink was estimated as 261.63 MJ/hl consisting of electrical (41.01%), thermal (58.81%) and manual (0.19%) of the total energy. The most energy intensive group operation was the Packaging House operation, followed by the Brew House operation with energy intensities of 223.19 and 35.94 MJ/hl, respectively. The exergy analysis revealed that the packaging house operation was responsible for most of the inefficiency (92.16%) followed by brew house operation (7.17%) and the silo house and filter room ...

2010-12-15

158

Pursuing energy supply options: cost effective R and D strategies. US Library of Congress. Report for the Joint Economic Committee, US Congress, April 27, 1981  

Energy Technology Data Exchange (ETDEWEB)

Large amounts of US public funds are deviated to energy-related R and D conflicts with the country's simultaneous attempts to control inflation and to limit federal government expansion. Congress must concentrate the funds at its disposal upon a manageable number of energy technologies - those most likely to improve the supply side of the domestic energy equation while maintaining an adequate return on investment. An examination of a wide array to technology alternatives concludes that (1) the development of unconventional gas would yield a large return while requiring only limited federal R and D support, (2) combined-cycle coal gasification and the manufacture of low- and medium-Btu gas need relatively little government aid and produce moderate returns, (3) although requiring limited support, energy from municipal solid waste (MSW) yields a small ...

1981-01-01

159

ORNL long-range environmental and waste management plan  

Energy Technology Data Exchange (ETDEWEB)

This report, the ORNL Long-Range Environmental and Waste Management Plan, is the annual update in a series begun in fiscal year 1985. Its primary purpose is to provide a thorough and systematic planning document to reflect the continuing process of site assessment, strategy development, and planning for the current and long-term control of environmental issues, waste management practices, and remedial action requirements. The document also provides an estimate of the resources required to implement the current plan. This document is not intended to be a budget document; it is, however, intended to provide guidance to both Martin Marietta Energy Systems, Inc., and the US Department of Energy (DOE) management as to the near order of magnitude of the resources (primarily funding requirements) and the time frame required to execute the strategy in the present ...

1989-09-01

160

Nuclear reactor closed Brayton cycle power conversion system optimization trends for extra-terrestrial applications  

International Nuclear Information System (INIS)

Extra-terrestrial exploration and development missions of the next century will require reliable, low-mass power generation modules of 100 kW_e and more. These modules will be required to support both fixed-base and manned rover/explorer power needs. Low insolation levels at and beyond Mars and long periods of darkness on the moon make solar conversion less desirable for surface missions. For these missions, a closed Brayton cycle energy conversion system coupled with a reactor heat source is a very attractive approach. The authors conducted parametric studies to assess optimized system design trends for nuclear-Brayton systems as a function of operating environment and user requirements. The inherent design flexibility of the closed Brayton cycle energy conversion system permits ready adaptation of the system to future design constraints. This paper describes a dramatic contrast ...

1990-08-12

161

Environmental Restoration Program quality assurance system requirements for the Hanford Site  

International Nuclear Information System (INIS)

This document defines the quality assurance program requirements for the US Department of Energy, Richland Field Office, Environmental Restoration program at the Hanford Site. This document integrates quality assurance requirements from US Department of Energy Orders, the Hanford Federal Facility Agreement and Consent Order, and applicable industry standards into a single source document for the development of quality assurance programs applicable to the Environmental Restoration program items and activities. This document has been configured into three parts and fifteen criteria to provide user organizations with a workable document that best facilitates line operations. When developing individual user organization quality assurance programs, the document configuration provides each organization with the Flexibility to incorporate only those parts and criteria that are applicable to their individual ...

162

Application of conventional laser technology to gamma-gamma colliders  

International Nuclear Information System (INIS)

A future e"-e"+ (electron-positron) linear collider can be configured with perhaps minimal modification to serve as an #gamma#-#gamma# (gamma-gamma) or a e"--#gamma# collider. This is accomplished by Compton-backscattering low energy photons (from a laser source) off of the high-energy electron beams prior to the crossing of the electron beams. However, to be competitive with the e"-e"+ configuration, the luminosity cannot be compromised in the process. This requires that the laser source deliver a sufficient number of photons per pulse with a pulse format and rate matching that of the electron beams. As it turns out, this requires an average optical power of 5 to 15 kW from the laser which is beyond the current state of the art. In this paper, the authors address how to generate the required pulse format and how the high average power requirement can be met ...

1994-03-28

163

Application of conventional laser technology to gamma-gamma colliders  

Energy Technology Data Exchange (ETDEWEB)

A future e{sup -}-e{sup +} (electron-positron) linear collider can be configured with perhaps minimal modification to serve as an {gamma}-{gamma} (gamma-gamma) or a e{sup -}-{gamma} collider. This is accomplished by Compton-backscattering low energy photons (from a laser source) off of the high-energy electron beams prior to the crossing of the electron beams. However, to be competitive with the e{sup -}-e{sup +} configuration, the luminosity cannot be compromised in the process. This requires that the laser source deliver a sufficient number of photons per pulse with a pulse format and rate matching that of the electron beams. As it turns out, this requires an average optical power of 5-15 kW from the laser which is beyond the current state of the art. In this paper, we address how to generate the required pulse format and how the high average power requirement ...

1995-02-01

164

Application of conventional laser technology to gamma-gamma colliders  

Energy Technology Data Exchange (ETDEWEB)

A future e{sup {minus}}e{sup +} (electron-positron) linear collider can be configured with perhaps minimal modification to serve as an {gamma}-{gamma} (gamma-gamma) or a e{sup {minus}}-{gamma} collider. This is accomplished by Compton-backscattering low energy photons (from a laser source) off of the high-energy electron beams prior to the crossing of the electron beams. However, to be competitive with the e{sup {minus}}e{sup +} configuration, the luminosity cannot be compromised in the process. This requires that the laser source deliver a sufficient number of photons per pulse with a pulse format and rate matching that of the electron beams. As it turns out, this requires an average optical power of 5 to 15 kW from the laser which is beyond the current state of the art. In this paper, the authors address how to generate the required pulse format and how the high average power ...

1995-02-01

165

Dietary energy requirements of young adult men, determined by using the doubly labeled water method  

International Nuclear Information System (INIS)

The autors examined the hypothesis that current recommendations on dietary energy requirements may underestimate the total energy needs of young adult men, by measuring total energy expenditure (TEE) and resting energy expenditure (REE) in 14 weight-maintaining healthy subjects leading unrestricted lives. TEE and body composition were measured by using 2H(2)18O, and REE was measured by using indirect calorimetry. All subjects had sedentary full-time occupations and participated in strenuous leisure activities for 34 #+-# 6 (SE) min/d. TEE and REE were 14.61 #+-# 0.76 and 7.39 #+-# 0.26 MJ/d, respectively, and 202 #+-# 2 and 122 #+-# 2 kJ.kg-1.d-1. There were significant relationships between TEE and both body fat-free mass (r = 0.732, P less than 0.005) and measured REE (r = 0.568, P less than 0.05). Measured TEE:REE values were significantly higher than the recommended ...

166

Safety design guide for pipe rupture protection for CANDU 9  

Energy Technology Data Exchange (ETDEWEB)

This safety design guide for pipe rupture protection identifies high-energy systems in which pipe ruptures must be postulated to occur, as well as systems that must be protected from the dynamic effects of such ruptures. Dynamic effects considered in this SDG consist of pipe whip (including missiles generated by pipe ruptures, if any) and jet impingement, Requirements for protection against the dynamic effects of a postulated pipe rupture and method of protection of essential structures, systems and components are specified for these effects. The change status for the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. 2 tabs., 5 refs. (Author) .new.

1996-03-01

167

Injection and extraction magnets: septa  

CERN Document Server

An accelerator has limited dynamic range: a chain of accelerators is required to reach high energy. A combination of septa and kicker magnets is frequently used to inject and extract beam from each stage. The kicker magnets typically produce rectangular field pulses with fast rise- and/or fall-times, however the field strength is relatively low. To compensate for their relatively low field strength, the kicker magnets are generally combined with electromagnetic septa. The septa provide relatively strong field strength but are either DC or slow pulsed. This paper discusses injection and extraction systems with particular emphasis on the hardware required for the septa.

2010-01-01

168

Electricity exchanges across international borders - 1983  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the electricity exchanges between the US and Mexico and Canada during calendar year 1983. The construction, operation and maintenance of any electric transmission facility which crosses an international border of the United States requires a Presidential Permit. These permits have been granted by the Department of Energy (DOE) since its formation in 1977. Between 1953 and 1977, these permits were issued by the former Federal Power Commission. Prior to 1953, they were issued by the President of the United States. Presidential Permits require that an annual report be filed by the permit holder detailing all transactions with the foreign country.

1984-09-01

169

Analysis of hydrogen vehicles with cryogenic high pressure storage  

Energy Technology Data Exchange (ETDEWEB)

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LIQ) or ambient-temperature compressed hydrogen (CH2). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (lower energy requirement for hydrogen liquefaction and reduced evaporative losses). This paper shows an evaluation of the applicability of the insulated pressure vessels for light-duty vehicles. The paper shows an evaluation of evaporative losses and insulation requirements and a description of the current experimental plans for testing insulated pressure vessels. The results show significant advantages to the use of insulated pressure vessels for light-duty vehicles.

1998-06-19

170

The BPX electrical power system  

International Nuclear Information System (INIS)

This paper reports on the Burning Plasma Experiment (BPX) which when operating at a toroidal field of 8.1 tesla and a plasma current of 10.6 megamps, requires peak power of 1235 megawatts and total pulse energy of over 21 gigajoules. These requirements are twice and over four times the corresponding figures for the Tokamak Fusion Test Reactor (TFTR), respectively. The design of the BPX power system has evolved, along with the tokamak, over a period of several years and has included studies of several alternative approaches. The reapplication of the existing TFTR power and energy facilities has been basic to all approaches. Among the new sources of pulse power and energy that have been considered are: direct utility grid pulsing, new flywheel units, and lead-acid storage batteries. The toroidal field power requirements are the greatest of the BPX subsystems and, ...

1991-10-03

171

NICE3: Dyebath reuse in carpet manufacturing  

Energy Technology Data Exchange (ETDEWEB)

Fact sheet on an analysis system for dyebath processes in the carpet manufacturing industry written for the NICE3 Program. The Georgia Institute of Technology (G.I.T.) has developed an effective automated dyebath analysis and reuse system that improves the energy, environmental, and economic performance of dyehouse batch operations. The new system enables dyeing solutions to be accurately monitored and adjusted for reuse. According to industry estimates, 160 pounds of water are used to produce each pound of textile product. The current wasteful batch dyeing process requires all water and residual chemicals, as well as the energy required to heat the mixture for dyeing, to be dumped after one application. Spent dyebaths can only be reused after they are sampled, analyzed, and reconstituted, a process requiring labor and expertise that are unavailable in the dyehouses. Therefore, ...

1999-09-29

172

Groundwater surveillance plan for the Oak Ridge Reservation  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5400.1 requires the preparation of environmental monitoring plans and implementation of environmental monitoring programs for all DOE facilities. The order identifies two distinct components of environmental monitoring, namely effluent monitoring and environmental surveillance. In general, effluent monitoring has the objectives of characterizing contaminants and demonstrating compliance with applicable standards and permit requirements, whereas environmental surveillance has the broader objective of monitoring the effects of DOE activities on on- and off-site environmental and natural resources. The purpose of this document is to support the Environmental Monitoring Plan for the Oak Ridge Reservation (ORR) by describing the groundwater component of the environmental surveillance program for the DOE facilities on the ORR. The distinctions between groundwater effluent monitoring and ...

1994-07-01

173

The effectiveness of reducing the daily dose of finasteride in men with benign prostatic hyperplasia  

UK PubMed Central (United Kingdom)

BackgroundFinasteride, a 5 alpha reductase inhibitor, is an established treatment for benign prostatic hyperplasia. The recommended dosage is 5 mg a day, however case reports have...Full Text Available

175

Serum alanine aminotransferase elevation during 10 days of acetaminophen administration in non-drinkers  

UK PubMed Central (United Kingdom)

Asymptomatic alanine aminotransferase (ALT) elevations have been detected with acetaminophen use at the maximum daily dose of 4 grams/day (g/d) for more than 3 consecutive days in subjects with...Full Text Available

2010-08-01

176

Performance evaluation of an automatic anatomy segmentation algorithm on repeat or four-dimensional CT images using a deformable image registration method  

UK PubMed Central (United Kingdom)

PurposeAuto-propagation of anatomical region-of-interests (ROIs) from the planning CT to daily CT is an essential step in image-guided adaptive radiotherapy. The...Full Text Available

2008-09-01

177

Metabolism of iodomethane in the rat  

UK PubMed Central (United Kingdom)

1. The LD50 of iodomethane orally administered to rats is 76mg./kg. body wt. but repeated daily doses of 30–50mg./kg. body wt. are without effect. 2. Oral doses of iodomethane to...Full Text Available

1966-01-01

178

Growth of Staphylococcus aureus MF 31 on the Top and Cut Surfaces of Southern Custard Pies  

UK PubMed Central (United Kingdom)

A Staphylococcus strain was inoculated on the top and cut surfaces of freshly baked Southern custard pies which were then packaged in a pasteboard carton and held at 30 C. Daily plate...Full Text Available

1969-07-01

179

Genetic association between the COMT genotype and urinary levels of tea polyphenols and their metabolites among daily green tea drinkers  

UK PubMed Central (United Kingdom)

Available in vitro and animal studies have shown cancer protective effects of tea polyphenols. Recent study suggests a greater protective effect of green tea intake on breast cancer...Full Text Available

180

Gasmap 2006. Bringing Norwegian gas to Europe; En publikasjon om norsk gass og gasseksport  

Energy Technology Data Exchange (ETDEWEB)

A publication on Norwegian gas and gas export. The content is wide spread from use of gas in daily life via sub sea pipeline repair systems to an overview over tomorrows gas fields. (AG)

2006-06-15

181

Extended-release Trazodone in Major Depressive Disorder  

UK PubMed Central (United Kingdom)

Objective: To investigate the efficacy, safety, and clinical benefit of a once-daily formulation of trazodone (Trazodone Contramid® OAD) in the treatment of major depressive...Full Text Available

182

Expression and Redistribution of Cellular Bad, Bax, and Bcl-xL Protein Is Associated with VCD-Induced Ovotoxicity in ...  

Science.gov (United States)

... were given daily i.p. injections of either sesame oil (2.5 ml/kg, vehicle control) or VCD dissolved in sesame oil (80 mg/kg, 0.57 mmol/kg) for ... ...

183

Evidence-based guidelines for the pharmacological treatment of postmenopausal osteoporosis: a consensus document by the Belgian Bone Club  

UK PubMed Central (United Kingdom)

Several drugs are available for the management of postmenopausal osteoporosis. This may, in daily practice, confuse the clinician. This manuscript offers an evidence-based update of previous treatment...Full Text Available

2010-10-01

184

Effects of Daily Morphine Administration and Deprivation on Choice and Demand for Remifentanil and Cocaine in Rhesus Monkeys  

UK PubMed Central (United Kingdom)

Choice procedures have indicated that the relative reinforcing effectiveness of opioid drugs increases during opioid withdrawal. The demand curve, an absolute measure of reinforcer value, has not been...Full Text Available

2011-01-01

185

Educational Challenges of Molecular Life Science: Characteristics and Implications for Education and Research  

UK PubMed Central (United Kingdom)

Molecular life science is one of the fastest-growing fields of scientific and technical innovation, and biotechnology has profound effects on many aspects of daily life—often with deep, ethical...Full Text Available

2010-01-01

186

Does treatment with cimetidine extended beyond initial healing of duodenal ulcer reduce the subsequent relapse rate?  

UK PubMed Central (United Kingdom)

Cimetidine 1 g daily is often continued for a fixed period beyond the time of healing of duodenal ulcer on the assumption that it might reduce the subsequent relapse rate. To test this, 194 patients...Full Text Available

1982-02-27

187

Cognitive performance in relapsing remitting multiple sclerosis: A longitudinal study in daily practice using a brief computerized cognitive battery  

UK PubMed Central (United Kingdom)

BackgroundThere is need for a cognitive test battery that can be easily used in clinical practice to detect or monitor cognitive performance in patients with multiple sclerosis (MS)....Full Text Available

188

Clinical review: Patency of the circuit in continuous renal replacement therapy  

UK PubMed Central (United Kingdom)

Premature circuit clotting is a major problem in daily practice of continuous renal replacement therapy (CRRT), increasing blood loss, workload, and costs. Early clotting is related to bioincompatibility,...Full Text Available

2007-01-01

189

Carbon Partitioning in Eelgrass (Regulation by Photosynthesis and the Response to Daily Light-Dark Cycles).  

UK PubMed Central (United Kingdom)

Diel variations in rates of C export, sucrose-phosphate synthase (SPS) and sucrose synthase (SS) activity, and C reserves were investigated in Zostera marina L. (eelgrass) to elucidate the environmental...Full Text Available

1995-08-01

190

A phase 1 study of BMS-275183, a novel oral analogue of paclitaxel given on a daily schedule to patients with advanced malignancies  

British Library Electronic Table of Contents (United Kingdom)

Summary Purpose BMS-275183 is an oral C-4 methyl carbonate analogue of paclitaxel that has the same mechanism of action, stabilization of tubulin polymerization. The present study was designed to: (i) assess the safety and tolerability of BMS-275183, and (ii) determine a suitable Phase II dose of BMS-275183 when given on a continuous daily schedule to patients with advanced solid tumor(s). Methods This was a multi-institutional, open-label, Phase I, single-arm dose escalation study in which cohorts of eligible patients with advanced malignancies were treated with BMS-275183 orally on a continuous daily schedule. The starting dose level was 6?mg/m2/day administered once daily. Cohorts of 3 patients were treated at each dose level provided no dose-limiting toxicities (DLTs) were observed. Ea...

2011-01-01

191

A once-daily dose of tadalafil for erectile dysfunction: compliance and efficacy  

UK PubMed Central (United Kingdom)

Selective phosphodiesterase type 5 inhibitors (PDE5Is) have revolutionized the treatment of erectile dysfunction (ED) in men. As an on-demand treatment, PDE5Is have excellent efficacy and safety in...Full Text Available

192

Performance prediction of 20 kWp grid-connected photovoltaic plant at Trieste (Italy) using artificial neural network  

International Nuclear Information System (INIS)

Growing of PV for electricity generation is one of the highest in the field of the renewable energies and this tendency is expected to continue in the next years. Due to the various seasonal, hourly and daily changes in climate, it is relatively difficult to find a suitable analytic model for predicting the performance of a grid-connected photovoltaic (GCPV) plant. In this paper, an artificial neural network is used for modelling and predicting the power produced by a 20 kWp GCPV plant installed on the roof top of the municipality of Trieste (latitude 45 deg. 40'N, longitude 13 deg. 46'E), Italy. An experimental database of climate (irradiance and air temperature) and electrical (power delivered to the grid) data from January 29th to May 25th 2009 has been used. Two ANN models have been developed and implemented on experimental climate and electrical data. The first one is a multivariate model based on the solar irradiance and the air ...

2010-12-01

193

Irradiation with and without razoxane in the treatment of incompletely resected or inoperable recurrent rectal cancer. Results of a small randomized multicenter study  

Energy Technology Data Exchange (ETDEWEB)

Background and Purpose: In an earlier phase II study, irradiation together with razoxane was shown to improve local control in recurrent rectal cancer. Therefore, the Austrian Society of Radiooncology (OeGRO) initiated a randomized controlled trial in 1992 to compare this combined treatment versus radiation therapy alone. Patients and Methods: Between 1992 and 1999, 36 patients with localized recurrences of rectal cancer were randomized to receive radiotherapy without (group A) or with razoxane (group B). The prognostic variables of the two groups were similar except for a longer median latency period from initial surgery to local recurrence in group A. High-energy photons with daily fractions between 170 and 200 cGy were used. The median total radiation dose was 60 Gy in each group. The patients in group B received a median razoxane dose of 9.6 g (range, 5-12 g). Main outcome measures were local control, overall survival, and toxicity. ...

2007-07-15

194

Implementation of integrated safeguards in Nuclear Fuel Plant at Pitesti, Romania  

International Nuclear Information System (INIS)

The nuclear activity was conducted for many years in Romania under Traditional Safeguards (TS) and has developed in good conditions the specific nuclear safeguards. Now there is a good opportunity to improve the performance and quality of the safeguards activity and at the same time to increase the accountancy and control of nuclear materials by passing to Integrated Safeguards (IS) implementation. The legal framework is the Law 100/2000 for ratification of the Protocol between Romania and International Atomic Energy Agency (IAEA), additional completion to the Agreement between the Socialist Republic of Romania Government and IAEA relating to safeguards. It is part of the Treaty on the non-proliferation of nuclear weapons published in the Official Gazette no. 3/31 January 1970, and the Additional Protocol published in the Official Gazette no. 295/ 29.06.2000. The first discussion about Integrated Safeguards (IS) between the Nuclear Fuel Plant (FCN) representatives ...

2009-10-12

195

Health and social impacts of biomass gasification for household energy in rural China: Assessment from three perspectives and emergent insights from their synthesis  

Science.gov (United States)

Solid fuels such as coal, wood, and crop straw supply some fraction of household cooking and heating fuel for more than one billion people in China. As these fuels do not generally combust cleanly in household stoves, their use levies large health and environmental burdens, particularly in rural regions. Production of clean-burning fuels from agricultural residue offers one prospect for mitigating health and social burdens imposed by household use of solid fuels. This dissertation explores the question: how might production of clean-burning household fuels from agricultural residues affect human health and social conditions in rural China? I approach this question from three perspectives. First, a technically plausible but currently unproven village-scale energy technology is explored in a scenario bounded by natural resources and substantiated by engineering specifications, estimates of indoor exposures to air pollution, and epidemiological analyses. This analysis ...

2005-01-01

196

Make Markets Work for Climate. Background Document  

Energy Technology Data Exchange (ETDEWEB)

Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies ...

2006-07-01

197

Waste sampling and characterization facility (WSCF) maintenance implementation plan  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP) is written to satisfy the requirements of the US Department of Energy (DOE) Order 4330.4B, Maintenance Management Program that specifies the general policy and objectives for the establishment of the DOE controlled maintenance programs. These programs provide for the management and performance of cost effective maintenance and repair of the DOE property, which includes facilities. This document outlines maintenance activities associated with the facilities operated by Waste Management Hanford, Inc. (WMH). The objective of this MIP is to provide baseline information for the control and execution of WMH Facility Maintenance activities relative to the requirements of Order 4330.4B, assessment of the WMH maintenance programs, and actions necessary to maintain compliance with the Order. Section 2.0 summarizes the history, mission and description of the WMH facilities. Section 3.0 ...

1997-08-13

198

Study on quality assurance for high-level radioactive waste disposal project  

International Nuclear Information System (INIS)

The U.S. Department of Energy (DOE) has developed comparatively detailed quality assurance requirements for the high-level radioactive waste disposal systems. Quality assurance is recognized as a key issue for confidence building and smooth implementation of the HLW program in Japan, and Japan is at an initial phase of repository development. Then the quality assurance requirements at site research and site selection, site characterization, and site suitability analysis used in the Yucca Mountain project were examined in detail and comprehensive descriptions were developed using flow charts. Additionally, the applicability to the Japan high-level radioactive waste disposal project was studied. The examination and study were performed for the following QA requirements: The requirements that have the relative importance at site research and site selection, site characterization, and ...

2005-03-01

199

RCRA Facilities Assessment (RFA)---Oak Ridge National Laboratory  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) facilities are required to be in full compliance with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established a Remedial Action Program (RAP) to provide comprehensive management of areas where past and current research, development, and waste management activities have resulted in residual contamination of facilities or the environment. This report presents the RCRA Facility Assessment (RFA) required to meet the requirements of RCRA Section 3004(u). Included in the RFA are (1) a listing of all sites identified at ORNL that could be considered sources of releases or potential releases; (2) background information on each of these sites, including location, type, size, period of operation, current operational status, and information on observed or potential releases (as ...

1987-03-01

200

Environmental monitoring at Kahe Point, Oahu, Hawaii for OTEC pilot-plant development  

Energy Technology Data Exchange (ETDEWEB)

Two 40 MWe Ocean Thermal Energy Conversion (OTEC) Pilot Plant programs are in the initial phase of development near Kahe Point, Oahu, Hawaii. The two options being examined are: (1) a shelf-seated artificial island, connected via a causeway to Oahu, using stainless steel heat exchangers, with the thermal resource enhanced by effluent from a near-by power plant, ammonia working fluid and biocide (chlorine) cleaning; and (2) a shelf mount tower 1 mile off shore using submerged aluminum heat exchangers, R-22 working fluid, and slurry cleaning with biocide (chlorine) backup. Environmental Technical Requirements are described including: siting criteria; environmental design, and operational criteria; thermal resource evaluation and variability; physical, chemical, and biological data requirements; and regulatory requirements. Due to siting, design, and operational differences the proposed two pilot plant ...

1982-08-01

201

Environmental Restoration Project quality system requirements for the Hanford Site. Revision 3  

International Nuclear Information System (INIS)

This document defines the quality system requirements for the US Department of Energy, Richland Operations Office (DOE-RL), Environmental Restoration (ER) Project at the Hanford Site. The Environmental Restoration Project Quality System Requirements for the Hanford Site integrates quality assurance requirements from the DOE Orders, the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement), the Hanford Facility Resource Conservation and Recovery Act of 1976 (RCRA) Permit, and applicable Federal and Washington State regulations. This document, based on ten criteria, provides user organizations with the flexibility to incorporate only those criteria and paragraphs applicable to their specific scopes of work. The requirements of this document are to be applied based on a graded approach that takes into consideration the risk inherent in, as well as the importance ...

202

Radiostrontium in milk and tap water. Appendix D  

International Nuclear Information System (INIS)

Results of monitoring milk and tap water in New York City are presented. The New York City sample is a monthly composite of pasteurized milk purchased daily at retail stores. The monthly "9"0Sr to calcium ratios for New York City since the inception of the sampling program in 1954 are presented. Samples of New York City tap water are taken daily, so that by the end of the month, approximately 100 liters have been collected. The available cesium-137 data expressed as the "1"3"7Cs to "9"0Sr ratio are also given.

1980-01-01

203

Turn-key Raman lidar for profiling atmospheric water vapor, clouds, and aerosols at the US Southern Great Plains Climate Study Site  

Energy Technology Data Exchange (ETDEWEB)

There are clearly identified scientific requirements for continuous profiling of atmospheric water vapor at the Department of Energy, Atmospheric Radiation Measurement program, Southern Great Plains CART (Cloud and Radiation Testbed) site in northern Oklahoma. Research conducted at several laboratories has demonstrated the suitability of Raman lidar for providing measurements that are an excellent match to those requirements. We have developed and installed a ruggedized Raman lidar system that resides permanently at the CART site, and that is computer automated to eliminate the requirements for operator interaction. In addition to the design goal of profiling water vapor through most of the troposphere during nighttime and through the boundary layer during daytime, the lidar provides quantitative characterizations of aerosols and clouds, including depolarization measurements for particle phase studies.

1997-12-31

204

Quality assurance requirements for high-level waste form production  

International Nuclear Information System (INIS)

The Department of Energy has issued a Quality Assurance (QA) specification for organizations involved in making a canistered high-level waste form product that is acceptable for storage in a deep geologic federal repository. The logic for the waste form acceptance process is described. In addition to NQA-1 requirements, fourteen supplemental QA requirements have been drafted to fit the waste form production process. A review plan for assuring complicance with the QA specification is provided. Guidelines for preparation of a waste form producer QA program are also presented. It is expected that the QA program description that result will be influential in supporting the acceptybility of the product to OCRWM and for ultimate disposal of the high-level waste in a deep geologic repository. (author) 3 figs., 4 refs.

205

DOE explosives safety manual  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy (DOE) policy requires that all DOE activities be conducted in a manner that protects the safety of the public and provides a safe and healthful workplace for employees. DOE has also prescribed that all personnel be protected in any explosives operation undertaken. The level of safety provided shall be at least equivalent to that of the best industrial practice. The risk of death or serious injury shall be limited to the lowest practicable minimum. DOE and contractors shall continually review their explosives operations with the aim of achieving further refinements and improvements in safety practices and protective features. This manual describes the Department's explosive safety requirements applicable to operations involving the development, testing, handling, and processing of explosives or assemblies containing explosives. It is intended to reflect the state-of-the-art in explosives ...

1991-10-01

206

Calculation of ventilation requirements in the case of intermittent pollution: application to enclosed parking garages  

Energy Technology Data Exchange (ETDEWEB)

The ventilation requirements for decontamination are normally determined with a static calculation method. In some cases, the pollutant emission is intermittent, for example in the car park of an office building, where all the cars enter and leave the place nearly at the same time. Generally, in such a case, the volume of the garage is large, consequently the time constant of the system has a high value. So a static approach would no longer stay accurate and a dynamic evaluation is needed. With the help of some assumptions, calculations remain rather simple and results can be plotted on nomographs or computed on a programmable handheld calculator. The amount of energy saved may appear very large in some cases. A sizing optimization will be required but also remains easy to compute. The paper presents the method of calculation for a single ventilation level and the optimization of a two-level ventilation.

1982-01-01

207

A network security case study; The Los Alamos National Laboratory integrated computer network  

Energy Technology Data Exchange (ETDEWEB)

This paper reports on a study to validate the Graphical Network Representation (GRPHREP) model which is being conducted on the Los Alamos National Laboratory Integrated Computer Network (ICN). The GRPHREP model is a software system application based on graph theory and object-oriented programming methodologies. It codified the Department of Energy (DOE) Order 5637.1, which is concerned with classified computer secret policy, restrictions, and requirements. The Los Alamos ICN is required to control access to and support large-scale scientific and administrative computing. Thus, large-scale scientific and administrative computing. Thus we felt that this large, complex, and dynamic network would provide a good test for the graphical and functional capabilities of the model. Furthermore, the ICN is composed of multiple partitions that reflect the sensitivity and classification of the computation (data) and designate the ...

1991-01-01

208

Structure formation and the origin of dark energy  

CERN Document Server

Cosmological constant a.k.a. dark energy problem is considered to be one major challenge in modern cosmology. Here we present a model where large scale structure formation causes spatially-flat FRW universe to fragment into numerous `FRW islands' surrounded by vacuum. We show that this mechanism can explain the origin of dark energy as well as the late time cosmic acceleration. This explanation of dark energy does not require any exotic matter source nor an extremely fine-tuned cosmological constant. This explanation is given within classical general relativity and relies on the fact that our universe has been undergoing structure formation since its recent past.

2007-01-01

209

Strengthening Clean Energy Technology Cooperation under the UNFCCC: Steps toward Implementation  

Energy Technology Data Exchange (ETDEWEB)

Development of a comprehensive and effective global clean technology cooperation framework will require years of experimenting and evaluation with new instruments and institutional arrangements before it is clear what works on which scale and in which region or country. In presenting concrete examples, this paper aims to set the first step in that process by highlighting successful models and innovative approaches that can inform efforts to ramp up clean energy technology cooperation. This paper reviews current mechanisms and international frameworks for global cooperation on clean energy technologies, both within and outside of the UNFCCC, and provides selected concrete options for scaling up global cooperation on clean energy technology RD&D, enabling environment, and financing.

2010-08-01

210

Report of the IPSM working party on low- and medium-energy x-ray dosimetry  

Energy Technology Data Exchange (ETDEWEB)

New values of the factors required to convert the reading of a radiation dosemeter calibrated in terms of air kerma (or exposure) into absorbed dose to water for medium-energy x-radiation were given in a code of practice published by the International Atomic Energy Agency in 1987. These are not considered to possess sufficient support from other sources. It is therefore recommended that the F-factors given or codes of practice should continue to be used. Values of backscatter factors for low-energy x-radiation (below 140 kV) in Supplement 17 of the British Journal of Radiology appear to be inaccurate. New values based on Monte Carlo calculations, and supported by new experimental data, are given for use in radiotherapy. (author).

1991-08-01

211

Report of the IPSM working party on low- and medium-energy x-ray dosimetry  

International Nuclear Information System (INIS)

New values of the factors required to convert the reading of a radiation dosemeter calibrated in terms of air kerma (or exposure) into absorbed dose to water for medium-energy x-radiation were given in a code of practice published by the International Atomic Energy Agency in 1987. These are not considered to possess sufficient support from other sources. It is therefore recommended that the F-factors given or codes of practice should continue to be used. Values of backscatter factors for low-energy x-radiation (below 140 kV) in Supplement 17 of the British Journal of Radiology appear to be inaccurate. New values based on Monte Carlo calculations, and supported by new experimental data, are given for use in radiotherapy. (author).

1991-01-01

212

H. R. 4553: a bill to provide fair incentives for the domestic production of oil and gas, and give flexibility to financial institutions with regard to energy and agricultural loans, and for other purposes. Introduced in the House of Representatives, Ninety-Ninth Congress, Second Session, April 10, 1986  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Energy Incentives and Agricultural Financial Resources Act of 1986 is to provide fair incentives for the domestic production of oil and gas, and to give flexibility to financial institutions with regard to energy and agricultural loans. The legislation reflects the current drop in activity and investment as a result of economic conditions and tax laws. It amends the Federal Deposit Insurance Act to assist troubled banks in providing capital and restructuring loans for energy development and agricultural pursuits. Title II repeals certain restrictions on the use of natural gas and petroleum imposed under the Fuel Use Act to open up markets and eliminate pricing requirements.

1986-01-01

213

Global challenges in energy  

International Nuclear Information System (INIS)

Environmental and security concerns are stimulating global interest in hydrogen power, renewable energy, and advanced transportation technologies, but no significant movement away from oil and a carbon-based world economy is expected soon. Over the longer-term, however, a transition from fossil fuels to a non-carbon-based economy will likely occur, affecting the type of environment future generations may encounter. Key challenges will face the world's energy industry over the next few decades to ensure a smooth transition-challenges which will require government and industry solutions beginning as early as today. This paper identifies four critical challenges in energy and the choices which will have to be made on how best to confront growing pollution caused by fossil fuels and how to facilitate an eventual revolutionary-like transition to a non-carbon-based global economy.

2006-10-01

214

Example of second-law efficiency of solar-thermal cavity receivers  

Energy Technology Data Exchange (ETDEWEB)

Properly quantified performance of a solar-thermal cavity receiver must not only account for the energy gains and losses as dictated by the First Law of thermodynamics, but it must also account for the quality of that energy. Energy quality can only be determined from the Second Law. In this paper, an equation developed for the Second-Law efficiency of a cavity receiver is presented as an evolution from the definition of available energy or ''availability'' (occasionally called exergy). The variables required are all either known or readily determined. The importance of considering the Second-Law is emphasized by a comparison of the First- and Second-Law efficiencies around an example of data collected from two receivers that were designed for different purposes, where the attempt was made to demonstrate that a Second-Law approach to quantifying ...

1986-02-01

215

Energy and nuclear power planning study for Thailand  

International Nuclear Information System (INIS)

The present report describes the study conducted in co-operation with several agencies and organizations from Thailand and covers the energy and electricity requirements and the optimal expansion plans for the power generating system for this country up to year 2011. It is emphasized that the study was carried out by a team of experts from the Electricity Generating Authority of Thailand (EGAT), the National Economic and Social Development Board (NESDB), the National Energy Administration (NEA) and the Office of Atomic Energy for Peace (OAEP), who were fully responsible for all phases of the study, including the production of the present report. The IAEA's responsibility was to provide overall co-ordination and general guidance during the conduct of the study, as well as training and assistance in the implementation and use of the IAEA's computerized planning methodologies on the computer facilities of ...

2002-06-16

216

Construction cost impact analysis of the U.S. Department of Energy mandatory performance standards for new federal commercial and multi-family, high-rise residential buildings  

Energy Technology Data Exchange (ETDEWEB)

In accordance with federal legislation, the U.S. Department of Energy (DOE) has conducted a project to demonstrate use of its Energy Conservation Voluntary Performance Standards for Commercial and Multi-Family High-Rise Residential Buildings; Mandatory for New Federal Buildings; Interim Rule (referred to in this report as DOE-1993). A key requisite of the legislation requires DOE to develop commercial building energy standards that are cost effective. During the demonstration project, DOE specifically addressed this issue by assessing the impacts of the standards on (1) construction costs, (2) builders (and especially small builders) of multi-family, high-rise buildings, and (3) the ability of low-to moderate-income persons to purchase or rent units in such buildings. This document reports on this project.

1993-12-01

217

A VRLA battery energy storage system for Metlakatla, Alaska  

Energy Technology Data Exchange (ETDEWEB)

The emergence of new power electronics and improved battery technology has created renewed interest in Battery Energy Storage Systems (BESS). These new systems provide electric utilities with alternatives to conventional storage technologies, such as pumped hydro. BESs has the potential to provide substantial benefits in terms of energy management, improved voltage, spinning reserve and protection from interruptions when compared to large centralized storage. This paper describes a commercial, economically justified, application of the new Battery Energy Storage Systems which is presently under construction in the Metlakatla Power and Light system. The paper outlines the system performance requirements which lead to consideration of BESS as an option; the economic factors which provided the justification for BESS as an economic alternative; and the overall BES system design and performance.

1996-11-01

218

Wetlands Assessment for site characterization, Advanced Neutron Source (ANS)  

Energy Technology Data Exchange (ETDEWEB)

This Wetlands Assessment has been prepared in accordance with the Department of Energy`s (DOE) Code of Federal Regulations (CFR) 10 CFR 1022, Compliance with Floodplain/Wetlands Environmental Review Requirements, which established the policy and procedure for implementing Executive Order 11990, Protection of Wetlands. The proposed action is to conduct characterization activities in or near wetlands at the ANS site. The proposed action will covered under a Categorical Exclusion, therefore this assessment is being prepared as a separate document [10 CFR 1022.12(c)]. The purpose of this Wetlands Assessment is to fulfill the requirements of 10 CFR 1022.12(a) by describing the project, discussing the effects of the proposed action upon the wetlands, and considering alternatives to the proposed action.

1994-10-01

219

Turkey's oil and natural gas pipelines system  

International Nuclear Information System (INIS)

Turkey's natural gas (NG) production is very small and is almost all imported. Turkish natural gas production in 2000, 23 billion cubic feet (Bcf), met around 4% of domestic natural gas consumption requirements. NG consumption is estimated at around 700 Bcf in year 2002, accounting for around 17% of Turkey's total energy consumption. Turkish natural gas demand had been projected to increase extremely rapidly in coming years. Country oil production is 50,674 barrels per day (bbl/d) of which 46,674 bbl/d was crude oil in 2002. In 2002, oil consumption was 635,000 bbl/d and net oil imports was 584,326 bbl/d in Turkey. Oil provides around 43% of Turkey's total energy requirements. (Author)

2005-07-15

220

Theoretical Standard Model Rates of Proton to Neutron Conversions Near Metallic Hydride Surfaces  

CERN Document Server

The process of radiation induced electron capture by protons or deuterons producing new ultra low momentum neutrons and neutrinos may be theoretically described within the standard field theoretical model of electroweak interactions. For protons or deuterons in the neighborhoods of surfaces of condensed matter metallic hydride cathodes, such conversions are determined in part by the collective plasma modes of the participating charged particles, e.g. electrons and protons. The radiation energy required for such low energy nuclear reactions may be supplied by the applied voltage required to push a strong charged current across a metallic hydride surface employed as a cathode within a chemical cell. The electroweak rates of the resulting ultra low momentum neutron production are computed from these considerations.

2006-01-01

221

Linac Coherent Light Source Longitudinal Feedback Model  

Energy Technology Data Exchange (ETDEWEB)

The Linac Coherent Light Source (LCLS) will be the world's first x-ray free-electron laser (FEL). To ensure the vitality of FEL lasing, it is critical to preserve the high quality of the electron beam during acceleration and compression. The peak current and final energy are very sensitive to system jitter. To minimize this sensitivity, a longitudinal feedback system on the bunch length and energy is required, together with other diagnostics and feedback systems (e.g., on transverse phase space). Here, we describe a simulation framework, which includes a realistic jitter model for the LCLS accelerator system, the RF acceleration, structure wakefield, and second order optics. Simulation results show that to meet the tight requirements set by the FEL, such a longitudinal feedback system is mandatory.

2005-06-15

222

High intensity lasers for gamma-gamma colliders  

Energy Technology Data Exchange (ETDEWEB)

Compton backscattering of laser photons near the interaction point of an e{sup +}e{sup -} or e{sup -}e{sup -} collider can be used to produce a {gamma}-{gamma} or {gamma}-e{sup -} collider. This paper describes the laser requirements, including pulse duration, intensity, energy, and wavelength, for such a collider. For most of the proposed, next generation, e{sup +}e{sup -} colliders, the laser wavelength should be in the near-infrared, with a pulse duration of 1 ps or less and an energy of similar 1 J per pulse. Current chirped pulse amplification laser systems in solid state lasing materials are well suited to meet these requirements. These systems are described. ((orig.)).

1995-02-01

223

Accounting-related transmission issues  

Energy Technology Data Exchange (ETDEWEB)

Various initiatives have been undertaken by the Federal Energy Regulatory Commission (FERC) to deregulate wholesale electric energy markets. These initiatives have focused on restructuring the transmission systems in the US and recently have culminated in a proposal requiring formation of and participation in regional transmission organizations. The overall form of regulation selected to determine rates for transmission entities as well as underlying regulatory decisions reached on key issues will have profound implications for transmission entities. For example, traditional cost-based regulation would require one set of accounting and reporting rules, while incentive-based regulation may not be subject to those same rules. An overview of some of the major accounting and financial reporting issues that will need to be considered is presented.

1999-12-01

224

Energy engineering and management: Continuing education in Australia  

Energy Technology Data Exchange (ETDEWEB)

It is important for Australia to recognize its own energy market and the opportunity to export its experience to fast developing Asian countries. Energy engineering and management becomes and important problem industrial engineers and managers face. Until 1993 there was no undergraduate or postgraduate course which would provide formal tertiary education in the proper application of energy conservation programs and load demand management techniques. These techniques require a special knowledge of energy systems which is a combination of electrical and mechanical engineering with a significant share of management techniques and economic calculations. This paper presents two teaching initiatives aimed at providing continuing education for engineers and managers. One is the Master of Engineering Sciences in Energy Engineering, developed by the Centre for Electrical ...

1995-12-31

225

Direct energy conversion for IEC fusion for space applications  

Energy Technology Data Exchange (ETDEWEB)

The paper describes a concept of extracting fusion power from D-{sup 3}He fueled IEC (Inertia Electrostatic Configuration) devices. The fusion system consists of a series of fusion modules and direct energy converters at an end or at both ends. This system of multiple units is linear and is connected by a magnetic field. A pair of coils anti-parallel to the magnetic field yields a field-null domain at the center of each unit as required for IEC operation. A stabilizing coil installed between the coil pairs eliminates the strong attractive force between the anti-parallel coils. Accessible regions for charged particle trajectories are essentially isolated from the coil structure. Thus, charged particles are directed along magnetic field lines to the direct energy converter without appreciable losses. A direct energy converter unit designed to be compatible to this unique system is also described. It ...

2000-08-01

226

Assessment of energy performance in the life-cycle of biogas production  

International Nuclear Information System (INIS)

Energy balances are analysed from a life-cycle perspective for biogas systems based on 8 different raw materials. The analysis is based on published data and relates to Swedish conditions. The results show that the energy input into biogas systems (i.e. large-scale biogas plants) overall corresponds to 20-40% (on average approximately 30%) of the energy content in the biogas produced. The net energy output turns negative when transport distances exceed approximately 200 km (manure), or up to 700 km (slaughterhouse waste). Large variations exist in energy efficiency among the biogas systems studied. These variations depend both on the properties of the raw materials studied and on the system design and allocation methods chosen. The net energy output from biogas systems based on raw materials that have high water content and low biogas yield (e.g. manure) is ...

2006-03-01

227

Proceedings. Future Energy - Resources, Distribution and Use  

Energy Technology Data Exchange (ETDEWEB)

Leading abstract. The goals of the Norwegian Academy of Technological Sciences (NTVA) are to promote research, education and development within technological and related sciences, for the benefit of the Norwegian society and for the development of Norwegian industry. Future energy policy and Global climate change are major issues in the Norwegian discussion today. The answers given have great influence on our industry and involve huge technological challenges. In the current situation NTVA wishes to contribute to the development of new technology. In 1998 the Norwegian Academy of Technological Sciences organized the seminar ''Do We Understand Global Climate Change''. NTVA have now followed this up with a seminar on the Energy System, one of the major sources of manmade greenhouse gases. The world's demand for energy increases with improvements in our standards of living. The ...

2001-07-01

228

Technical considerations associated with waste-to-energy systems  

Energy Technology Data Exchange (ETDEWEB)

The average American generates four pounds of solid waste per day, yet increasing constraints are being placed on the ability of municipalities to handle waste disposal. Most cities face a scarcity of acceptable landfill sites and conventional incineration and landfill methods have come under strict air, water and soil pollution standards. City administrators are being encouraged to select from a variety of proposed technologies that supplant traditional waste disposal methods, some of which offer the promise of revenues from energy and resource recovery. The problem is to select from available near-term technologies those systems that will fit into a city's long-term solid-waste management program. Broadly, waste-to-energy recovery systems now available to cities may be classified as combustion, pyrolysis, biodegradation, and mechanical front-end systems. It is important to notice that operations used for mechanical front-end systems ...

1981-01-01

229

Coordination of air pollution abatement. Ilmansuojeluohjelmien yhteensovittaminen  

Energy Technology Data Exchange (ETDEWEB)

Finland has set up several national air pollution control programmes in order to implement international conventions. As a rule these programmes have focused on one pollutant. The national second carbon dioxide commission is at present working on a new programme to curb carbon dioxide emissions, and this will unavoidably affect other programmes, too. This study presents the existing programmes and their respective implementation costs. The aim has been to focus on the interaction between different air pollution combatting measures and the possibilities of setting priorities on a cost basis. The main result is that it will be difficult to integrate overall aims for general welfare and subsequent energy consumption with environmental considerations, especially in air pollution control. If the increase in energy generation follows current scenarios, the costs for air pollution abatement measures will require a considerable ...

1992-01-01

230

Washington: a guide to geothermal energy development  

Energy Technology Data Exchange (ETDEWEB)

A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined. (MHR)

1980-01-01

231

The ANL X6B beamline at NSLS: A versatile facility  

Energy Technology Data Exchange (ETDEWEB)

We have described the x-ray optics and beamline performance of the ANL X6B beam line at the NSLS. Considerable flexibility has been built into the beam line to accommodate a wide range of x-ray diffraction, scattering, and spectroscopy experiments with various requirements. We presented selected examples of experimental results and showed that with the high intensity, high energy resolution, high-q resolution, and energy tunability, the X6B beam line has become a versatile facility.

1994-07-01

232

Radiant heating and cooling, displacement ventilation with heat recovery and storm water cooling: An environmentally responsible HVAC system  

Energy Technology Data Exchange (ETDEWEB)

This paper describes the design, operation, and performance of an HVAC system installed as part of a project to demonstrate energy efficiency and environmental responsibility in commercial buildings. The systems installed in the 2180 m{sup 2} office building provide superior air quality and thermal comfort while requiring only half the electrical energy of conventional systems primarily because of the hydronic heating and cooling system. Gas use for the building is higher than expected because of longer operating hours and poor performance of the boiler/absorption chiller.

1998-12-31

233

Progress of the BT-EdF-CEA project. The lithium polymer battery; Avancees du projet BT-EdF-CEA. Batterie lithium polymere  

Energy Technology Data Exchange (ETDEWEB)

The lithium-polymer energy storage technology requires the production of thin films of huge surface. The BT-EdF-CEA consortium has studied the various manufacturing techniques of these films and their assembly. The process was chosen according to its productivity, low expensiveness, ecological impact and energy performances with capacities reaching 40 Ah. This paper explains: the objectives and specifications of the project, the advantage of the consortium and the role of the different partners, the results (coating, dry extrusion and battery element manufacturing techniques), and the electrochemical performances of the elements. (J.S.)

1996-12-31

234

Phase-space analysis of interacting phantom cosmology  

CERN Document Server

We perform a detailed phase-space analysis of various phantom cosmological models, where the dark energy sector interacts with the dark matter one. We examine whether there exist late-time scaling attractors, corresponding to an accelerating universe and possessing dark energy and dark matter densities of the same order. We find that all the examined models, although accepting stable late-time accelerated solutions, cannot alleviate the coincidence problem, unless one imposes a form of fine-tuning in the model parameters. It seems that interacting phantom cosmology cannot fulfill the basic requirement that led to its construction.

2008-01-01

235

PAMELA results on the cosmic-ray antiproton flux from 60 MeV to 180 GeV in kinetic energy  

CERN Document Server

The satellite-borne experiment PAMELA has been used to make a new measurement of the cosmic-ray antiproton flux and the antiproton-to-proton flux ratio which extends previously published measurements down to 60 MeV and up to 180 GeV in kinetic energy. During 850 days of data acquisition approximately 1500 antiprotons were observed. The measurements are consistent with purely secondary production of antiprotons in the galaxy. More precise secondary production models are required for a complete interpretation of the results.

2010-01-01

236

Local wind patterns for modelling renewable energy systems by means of cluster analysis techniques  

Energy Technology Data Exchange (ETDEWEB)

A method based on cluster analysis techniques is proposed in order to obtain representative local wind patterns. Modeling renewable energy systems, in an accurate way which strongly depends on wind loads, requires reliable data to analyze their response and evaluate their performance. Otherwise poor agreement with the models may be obtained. In a case study for La Paz, Baja California Sur, Mexico, four different wind patterns were obtained from a one-year data set recorded at 10-min intervals. (author)

2002-02-01

237

Local secondary-electron emission spectra of graphite and gold surfaces obtained using the Scanning Probe Energy Loss Spectrometer (SPELS)  

International Nuclear Information System (INIS)

Secondary-electron emission (SEE) spectra have been obtained with the Scanning Probe Energy Loss Spectrometer at a tip-sample distance of only 50 nm. Such short working distances are required for the best theoretical spatial resolution (<10 nm). The SEE spectra of graphite, obtained as a function of tip bias voltage, are shown to correspond to unoccupied states in the electronic band structure. The SEE spectra of thin gold films demonstrate the capability of identifying (carbonaceous) surface contamination with this technique.

2009-11-25

238

Innovative financing for future petroleum industry requirements  

Energy Technology Data Exchange (ETDEWEB)

Many energies companies rely heavily on the financial markets to fund expansion plans due to the capital intensive nature of this industry. The dramatic and rapid changes in the financial markets over the last few years create both challenges and opportunities for oil and gas companies trying to survive a volatile era and to position themselves for recovery. These market volatilies have bred new financial techniques and opportunities in both the domestic and global capital markets. This paper discusses specific applications, benefits and advantages of these new techniques and financial products to energy companies.

1988-01-01

239

Fluidized-bed energy technology for biomass conversion  

Science.gov (United States)

Fluidized bed technology was experimentally evaluated for the combustion and gasification of cotton gin waste. The isothermal bed temperatures in the reactors could be maintained below the ash fusion point of the waste. Raw stripper harvested cotton gin trash could be metered directly into the fluidized-bed reactors indicating that little feed preparation is required. H and CO were the primary products of gasification, and approximately 3200-400 Btu of gas were produced per lb of cotton gin waste. These techniques offer the potential of providing small-scale energy conversion systems for use on farms.

1980-01-01

240

Energy planning in developing countries: the role of microcomputers  

Energy Technology Data Exchange (ETDEWEB)

Microcomputers are beginning to be used for energy analysis in many developing countries, and have the potential for making a significant contribution to the resolution of difficult analytical and data problems, and to improving communications between analyst and decision maker. Successful introduction of a microcomputer based on analytical capability, however, requires attention to several important factors in order to avoid the mistakes of the earlier mainframe computer era. This paper reviews the key issues of matching models to staff capabilities, of training, and of the operating environment, based on the author's first-hand experience with microcomputer projects in Uruguay, Haiti and Sri Lanka. 3 figures, 3 tables.

1985-02-01

241

Energy and technology review  

Energy Technology Data Exchange (ETDEWEB)

The state of the laboratory address by LLNL Director Roger Batzel is summarized, and a breakdown of the laboratory funding is given. The Livermore defense-related committment is described, including the design and development of advanced nuclear weapons as well as research in inertial confinement fusion, nonnuclear ordnance, and particle beam technology. LLNL is also applying its scientific and engineering resources to the dual challenge of meeting future energy needs without degrading the quality of the biosphere. Some representative examples are given of the supporting groups vital for providing the specialized expertise and new technologies required by the laboratory's major research programs. (GHT)

1982-07-01

242

Alaska: a guide to geothermal energy development  

Energy Technology Data Exchange (ETDEWEB)

A brief overview is given of the geological characteristics of each region of the state as they relate to potential geothermal development. Those exploration methods which can lead to the siting of a deep exploration well are described. Requirements and techniques needed for drilling deeper higher temperature exploration and production wells are presented. Electrical generation, direct utilization, and indirect utilization are reviewed. Economic factors of direct use projects are presented. A general guide to the regulatory framework affecting geothermal energy development is provided. The general steps necessary to gain access to explore, develop, distribute, and use geothermal resources are outlined. (MHR)

1980-06-01

243

Role of Fusion Energy in a Sustainable Global Energy Strategy  

Energy Technology Data Exchange (ETDEWEB)

Fusion energy is one of only a few truly long-term energy options. Since its inception in the 1950s, the vision of the fusion energy research program has been to develop a viable means of harnessing the virtually unlimited energy stored in the nuclei of light atoms--the primary fuel deuterium is present as one part in 6,500 of all hydrogen. This vision grew out of the recognition that the immense power radiated by the sun is fueled by nuclear fusion in its hot core. Such high temperatures are a prerequisite for driving significant fusion reactions. The fascinating fourth state of matter at high temperatures is known as plasma. It is only in this fourth state of matter that the nuclei of two light atoms can fuse, releasing the excess energy that was needed to separately bind each of the original two nuclei. Because the nuclei of atoms carry a net positive electric charge, they repel ...

2001-03-07

244

Energy and materials flows in the production of olefins and their derivatives  

Energy Technology Data Exchange (ETDEWEB)

Production of olefins and their derivatives uses almost 3.5% of the oil and gas consumed annually in the United States. It is estimated that their production requires an input energy of 2 Q, which is 50% of the energy used in the production of all petrochemicals. Substantial amounts of this energy could be recovered through recycling. For example, recycling of a single plastic product, polyester soft drink bottles, could have recovered about 0.014 Q in 1979. (About 1.4 Q is used to produce plastic derivatives of olefins). Petrochemical processes use fuels as feedstocks, as well as for process energy, and a portion of this energy is not foregone and can be recovered through combustion of the products. The energy foregone in the production of ethylene is estimated to be 7800 Btu/lb. The energy foregone in plastics ...

1980-08-01

245

Energy Nation Norway. Development and renewal in a new environmental and geopolitical era. Summary; KonKraft rapport 1  

Energy Technology Data Exchange (ETDEWEB)

'Energy Nation Norway' looks at Norway as an energy nation from both a national and an international perspective. Its purpose is to provide a basis for political and industrial decisions relating to the petroleum industry. The report is particular concerned with the petroleum sector, besides considering the Norwegian energy cluster from a broader perspective. The energy cluster has been and will continue to be a crucial vehicle for economic growth and the development of wealth in Norway. These are the report's main conclusions: The petroleum industry has played a significant part in Norway's economic development, the side-effects of which have benefited the country's entire population. The world's economic growth and wealth development require energy. In the next few decades oil and gas will continue to form ...

2008-07-01

246

Depleted uranium munitions - where are we now?  

International Nuclear Information System (INIS)

There are very different views on the health hazards of DU munitions. Most of the concerns of veterans and their advisors focus on the radiological effects of DU and consequently these are the focus of this editorial. Effects on the kidney and environmental consequences are, however, considered in the second of the Royal Society reports and the main conclusions of both of the reports are outlined in the summary document published in this issue of the journal. The main radiological concerns focus on the irradiation of lung tissues from inhaled DU particles and irradiation resulting from the translocation of inhaled particles to the thoracic lymph nodes.The overwhelming scientific view, presented in the two Royal Society reports and in other independent reviews, is that the main risks of exposure to DU aerosols are an increase in lung cancer and (from chemical toxicity) damage to the kidney, although these are likely to be evident only following substantial intakes. The equivalent doses ...

2002-06-01

247

Review of compliance with EU-2010 targets on renewable energy in Galicia (Spain)  

Energy Technology Data Exchange (ETDEWEB)

The use of renewable energy offers a range of exceptional benefits, including: a decrease in external energy dependence; a boost to local and regional component manufacturing industries; promotion of regional engineering and consultancy services specialising in the use of renewable energy; increased R and D, decrease in impact of electricity production and transformation; increase in the level of services for the rural population; creation of employment, etc. To achieve these benefits, a series of actions are required, among which the following are particularly important: creation of a suitable climate for performing R and D; training of technicians in design, production and maintenance of equipment; motivation for establishing a new market; proper financing; fostering of appropriate technologies; practical demonstration of results, etc. This article reviews the progress made in the Autonomous Community ...

2006-06-15

248

Low temperature heating systems. More comfort with less energy; Lage temperatuursystemen. Meer comfort met minder energie  

Energy Technology Data Exchange (ETDEWEB)

To realise the Dutch objectives of energy saving and emission reductions in the built environment, the use of 'Low Valued Energy' will be necessary in the future. Low Valued Energy is available from residual, ambient heat and renewable sources. Using Low Valued Energy for space heating in commercial and residential buildings requires adjusting the design of the installations, i.e. lowering the design supply temperature of the heating system from 90C to 55C or less. Appropriate heat distribution systems, e.g. floor or wall heating and radiators, have a life cycle of 40 to 50 years. The application (on a large scale in buildings), however, requires an enormous change in the installation and building branch. To enable the application of low temperature sources in the future, the building and installation designs should be based on low temperature ...

2000-06-01

249

Enduse Global Emissions Mitigation Scenarios (EGEMS): A New Generation of Energy Efficiency Policy Planning Models  

Energy Technology Data Exchange (ETDEWEB)

This paper presents efforts to date and prospective goals towards development of a modelling and analysis framework which is comprehensive enough to address the global climate crisis, and detailed enough to provide policymakers with concrete targets and achievable outcomes. In terms of energy efficiency policy, this requires coverage of the entire world, with emphasis on countries and regions with large and/or rapidly growing energy-related emissions, and analysis at the 'technology' level-building end use, transport mode or industrial process. These elements have not been fully addressed by existing modelling efforts, which usually take either a top-down approach, or concentrate on a few fully industrialized countries where energy demand is well-understood. Inclusion of details such as appliance ownership rates, use patterns and efficiency levels throughout the world allows for a ...

2009-05-29

250

Waste Diversion | Greening EPA | US EPA  

Wastenet

...diversion generates a host of environmental, financial, and social benefits, including conserving energy, reducing disposal costs, and reducing the burden on landfills and other waste disposal methods . Waste Diversion at EPA For many years, EPA has established waste diversion goals that exceed current federal requirements. EPA ...

251

Ventilation intensity - Influence on the air quality and its calculation method; Die Lueftungsintensitaet - Auswirkung auf die Luftqualitaet und deren Berechnungsmethoden  

Energy Technology Data Exchange (ETDEWEB)

Because of good thermal insulation of advanced energetic buildings and their good airtightness the air hygiene is insufficient. A normal ventilation behaviour by window opening consumes too much heating energy. A calculation method is shown taking into account a required air change number, flow rate and indoor air quality as thermal comfort in the rooms occupied by different number of persons. (GL)

2006-07-01

252

Thermodynamic calculations for Otto cycle engines using methanol as a fuel  

Energy Technology Data Exchange (ETDEWEB)

Equations are derived to calculate the work required for the isentropic compression of a 2-phase fuel-air mixture. Methanol evaporation during compression substantially reduces compression work and improves cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. Energy d. of methanol and gasoline fuel-air charges are compared. The phase equilibrium and evaporation rate are causes of the poor cold-starting performance of methanol.

1981-01-01

253

Thermal hazards of explosives  

Energy Technology Data Exchange (ETDEWEB)

Small-scale methods for determining the reaction rates of explosives that make it possible to predict safe temperatures for using them, and methods for testing the accuracy of these predictions were developed. Each different size and shape of each different explosive has its own critical temperature. The ability to predict these critical temperatures is required before high-energy materials can be used safely.

1981-03-01

254

Spectrum measurement of neutrons from 40 MeV alpha particle bombardment of tantalum  

International Nuclear Information System (INIS)

The energy distribution of neutrons generated due to bombardment of 40 MeV alpha particles on thick elemental tantalum is measured using threshold activation detectors. A method of unfolding the neutron spectrum from the activation data based on information-entropy weighted average solution is described. The present unfolding method does not require 'a priori' information about the shape of the solution spectrum. 16 refs. (author).

255

SOLERAS - Solar Controlled Environment Agriculture Project. Final report, Volume 4. Saudi Engineering Solar Energy Applications System Design Study  

Energy Technology Data Exchange (ETDEWEB)

Literature summarizing a study on the Saudi Arabian solar controlled environment agriculture system is presented. Specifications and performance requirements for the system components are revealed. Detailed performance and cost analyses are used to determine the optimum design. A preliminary design of an engineering field test is included. Some weather data are provided for Riyadh, Saudi Arabia. (BCS)

1985-01-01

256

Risk-orientated analysis of the SNR 300. Technical report 1  

International Nuclear Information System (INIS)

The study required by the West German Ministry of Research and Technology (RS 605) for the Committee on 'Future Nuclear Energy Policy' of the 9th German Parliament is concerned with the following main points: 1) Assessment of technical risks from the social aspect; 2) Discussion of terms and quantification of risks; 3) 'Engineering judgment' and 'questionable' methods in the Fast Breeder analysis of the Society for Reactor Safety (GRS); 4) Assessment criteria of potential damage. (HP).

257

Return on investment (ROI) proposal preparation guide  

Energy Technology Data Exchange (ETDEWEB)

The ROI Proposal Preparation Guide is a tool to assist Hanford waste generators in preparing ROI proposal forms for submittal to Department of Energy, Richland Operations Office (DOE/RL) for funding. The guide describes the requirements for submitting an ROI proposal and provides examples of completed ROI forms. The intent is to assist waste generators in identifying projects that meet the criteria, provide information necessary to complete the ROI forms, and submit a proposal that is eligible to receive funding.

1998-10-09

258

Recommendations and quality control in brachytherapy; Recommandations pour le controle de qualite en curietherapie  

Energy Technology Data Exchange (ETDEWEB)

Brachytherapy consists of sealed radioactive source implantation. The diversity in the nature of radioelements, in their energy and activity requires strict implantation and utilization rules. These rules include radioactive source physical parameters check, after-loading machine and treatment planning system quality assurance and safe and reproducible dosimetric systems. Patient and medical workers information guarantee radioprotection and prevention of accidental exposures. (authors)

2002-11-01

259

Polychlorinated Biphenyl Presence in the Columbia River Corridor  

Energy Technology Data Exchange (ETDEWEB)

The U. S. Department of Energy (DOE) is required by Comprehensive Environmental Response, Compensation, and Liability Act of 1980 regulations to develop a conceptual understanding of potential contaminant releases from the Hanford Site based on an evaluation of existing data and known historical practices. Polychlorinated biphenyls (PCBs) are one environmental contaminant potentially released through leaks, spills, or disposal. This document presents a summary of selected relevant existing information, including environmental studies and Hanford Site analytical data.

2007-09-06

260

Motor drive chassis for the plutonium protection system  

International Nuclear Information System (INIS)

A motor drive chassis has been developed for use in the Plutonium Protection System. Rotation of the desired carrousel in a secure storage module is controlled by this chassis which supplies the power and drive pulses required by the carrousel motor. This work was sponsored by the Department of Energy/Office of Safeguards and Security (DOE/OSS) as part of the overall Sandia Fixed Physical Protection Program.

1998-10-12

261

Methane fermentation of agricultural wastes and domestic animal's wastes  

Energy Technology Data Exchange (ETDEWEB)

Cattle and pig wastes, orange peels, compost, and grain husks were hydrolyzed in an alkaline medium to investigate the CH4 generation capacity. The respective CH4 production capacities from pig wastes and rice hulls were approximately 1 and approximately 0.1 L/g. The CH4 produced can be used to supplement energy requirements of farms.

1981-01-01

262

Integrated Safety Management System Phase I Verification for the Plutonium Finishing Plant (PFP) [VOL 1 & 2  

Energy Technology Data Exchange (ETDEWEB)

U.S. Department of Energy (DOE) Policy 450.4, Safety Management System Policy commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex as a means of accomplishing its missions safely. DOE Acquisition Regulation 970.5204-2 requires that contractors manage and perform work in accordance with a documented safety management system.

2000-01-10

263

Evolution of the chromospheres and winds of low- and intermediate-mass giant stars  

International Nuclear Information System (INIS)

Results are presented of an empirical analysis of the global thermodynamical requirements of the winds in the outer atmospheres of a representative sample of red giant stars of low- and intermediate-mass range. Results indicate that the mass-loss rates in these stars are not strongly dependent on the actual physical processes driving the winds. It is suggested that nonlinear processes act to regulate wind energy fluxes. Possible mechanisms responsible for the chromospheric heating and the mass loss in the low- and intermediate-mass giant stars are discussed. 151 refs.

264

Evaluation of technology modifications required to apply clean coal technologies in Russian utilities. Final report  

Energy Technology Data Exchange (ETDEWEB)

The report describes the following: overview of the Russian power industry; electric power equipment of Russia; power industry development forecast for Russia; clean coal technology demonstration program of the US Department of Energy; reduction of coal TPS (thermal power station) environmental impacts in Russia; and base options of advanced coal thermal power plants. Terms of the application of clean coal technology at Russian TPS are discussed in the Conclusions.

1995-12-01

265

Energy saving technologies for protected horticulture - commercial demonstration and technology transfer  

Environmental Research Database

DescriptionFollowing publication of the Curry report, DEFRA have made a commitment to establish a number of pilot projects supporting a network of demonstration and development farms. These 'farms' are intended to support the process of technology transfer by giving free access to information on the practical application of new, emerging and best practice technologies. Protected Horticulture has been identified as a sub-sector requiring the establishment of one of these projects. One of the major pressures [continued...

2005-01-31

266

Design of the local trigger board for the Daya Bay reactor neutrino experiment  

British Library Electronic Table of Contents (United Kingdom)

We have designed a local trigger board for the Daya Bay reactor neutrino experiment, which is aimed to measure the neutrino mixing angle sin22?13 with a precision down to 1% level. The local trigger board processes both the total number of coincident photomultiplier tube (PMT) hits and the PMT energy sum to make trigger decisions. With this design, a high trigger probability is achieved to meet the system requirement. The design of the local trigger board is presented.

2011-01-01

267

DNA-new combination: a practical application in the sugar industry  

Energy Technology Data Exchange (ETDEWEB)

One of the first technical applications of gene technology is reported here. The DNA of E. coli cells was rearranged such that these cells produce large quantities of the enzyme ..cap alpha..-galactosidase. This enzyme is used to split the trisaccharide, raffinose, which is formed during the production of sugar from sugar beet. By this means sugar yields can be increased and the energy required for sugar crystallisation reduced.

1983-04-01

268

Basic consideration on high power free-electron lasers  

Energy Technology Data Exchange (ETDEWEB)

An FEL amplifier to generate a laser power of the order of TW at 4 {mu}m wavelength is investigated for a {gamma}-{gamma} collider. A concept of an amplifier chain consisting of a phase-displacement deceleration FELs is proposed to increase the FEL efficiency and to mitigate the requirement for the beam energy spread. The feasibility of the driving linac for the FEL system is also discussed. ((orig.)).

1995-02-01

269

Basic consideration on high power free-electron lasers  

International Nuclear Information System (INIS)

An FEL amplifier to generate a laser power of the order of TW at 4 #mu#m wavelength is investigated for a #gamma#-#gamma# collider. A concept of an amplifier chain consisting of a phase-displacement deceleration FELs is proposed to increase the FEL efficiency and to mitigate the requirement for the beam energy spread. The feasibility of the driving linac for the FEL system is also discussed. ((orig.)).

270

Assessment of internal contamination due to gamma emitters at nuclear power stations of Tarapur  

International Nuclear Information System (INIS)

Personal monitoring and dose assessment of all radiation workers is an essential regulatory requirement as per radiation safety procedures of AERB and operating stations. The occupational workers of TAPS 1 and 2 and TAPS 3 and 4 are monitored for internal contamination due to high energy gamma emitters by whole body counting

2010-02-03

271

A desiccant dehumidifier for electric vehicle heating  

Energy Technology Data Exchange (ETDEWEB)

Vehicle heating requires a substantial amount of energy. Engines in conventional cars produce enough waste heat to provide comfort heating and defogging/defrosting, even under very extreme conditions. Electric vehicles (EVs), however, generate little waste heat. Using battery energy for heating may consume a substantial fraction of the energy storage capacity, reducing the vehicle range, which is one of the most important parameters in determining EV acceptability. Water vapor generated by the vehicle passengers is in large part responsible for the high heating loads existing in vehicles. In cold climates, the generation of water vapor inside the car may result in water condensation on the windows, diminishing visibility. Two strategies are commonly used to avoid condensation on windows: windows are kept warm, and a large amount of ambient air is introduced in the vehicle. Either strategy results in a ...

1996-09-01

272

Cooperative procurement: market transformation for energy efficient products  

Energy Technology Data Exchange (ETDEWEB)

Cooperative procurement is a variation of public purchasing which may be used as an instrument to transform the market and stimulate innovation enhancing environmental performance. The core of the procedure is the following: Coordinated by a central agency a group of buyers - public administrations, but also private companies, associations, etc. - gets together and jointly formulates a catalogue of performance requirements for a specific product truly suiting their preferences. This catalogue may contain (combinations of) requirements not yet available on the market and includes energy efficiency and/or environmental performance among other preferences important to the users. On the basis of the product requirements the buyer group launches a call for tenders, evaluates the bids received from the manufacturers and commits to buying the winning product. Thus, a market is provided for the most successful ...

1999-07-01

273

Application of LBB to high energy pipings of PWR in Korea  

Energy Technology Data Exchange (ETDEWEB)

The application of the LBB technology to the newly constructed PWRs has been approved in Korea for several high energy systems that can meet rigorous acceptance criteria. The LBB evaluation had been initiated for Yong-Gwang 3 and 4 units (YGN 3 and 4) which are in service, and subsequently performed for Ul-Chin 3 and 4 units (UCN 3 and 4) which are in construction. The LBB application in Korea is based on the USNRC requirements. The LBB evaluation for YGN 3 and 4 is to eliminate the dynamic effects associated with the postulated DEGB from design basis loads as well as to eliminate pipe whip restraints and jet impingement barriers. There were several issues on the application of LBB to the primary coolant loop and the pressurizer surge line. Of concern were material properties of carbon steel for the primary coolant loop, estimation of crack opening area at the pipe-to-nozzle interface considering the asymmetry, and the leakage crack size which ...

1996-12-31

274

Quality assurance requirements for high-level waste form production  

International Nuclear Information System (INIS)

The US Department of Energy (DOE) Defense Waste Management Plan has the objective of final disposal for high-level waste (HLW) generated from defense programs. The DOE sites that generate HLW are located at the Savannah River Operations Office in Aiken, South Carolina, the Hanford site in Richland, Washington, and the Idaho Operations Office in Idaho Falls, Idaho. The purpose in the development of a quality assurance (QA) specification for organizations involved in HLW production is to establish uniform requirements that ensure that radioactive waste is converted to a waste form and canistered in such a way that it is acceptable in a federal repository licensed by the US Nuclear Regulatory Commission (NRC). A QA specification has been developed that will be applied to those activities important to certification of the product. The basic requirements are defined in national consensus standards and DOE directives. The ...

1988-06-12

275

Fiscal year 1996 U.S. Department of Energy, Richland Operations Office Site summary baseline  

International Nuclear Information System (INIS)

The technical baseline is a hierarchical description of the Hanford Site cleanup mission. This technical baseline does not address the science, technology, or economic transition missions. It begins with a definition of the existing conditions at the Hanford Site, provides a description of the end product or mission accomplishments at completion, presents a statement of the major requirements and constraints that must be observed during the performance of the mission, and provides a statement of the top-level strategic approach to accomplish the mission. Mission-level interfaces are also described. This information is further defined hierarchically in increasing levels of detail. This definition is composed of the following major elements: functions that are key task descriptions; requirements that are the measurable standards to which the functions must be performed; architectures which are specific engineering solutions or systems that ...

2009-06-01

276

DOE explosives safety manual  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy (DOE) policy requires that all activities be conducted in a manner that protects the safety of the public and provides a safe and healthful workplace for employees. DOE has also prescribed that all personnel be protected in any explosives operation undertaken. The level of safety provided shall be at least equivalent to that of the best industrial practice. The risk of death or serious injury shall be limited to the lowest practicable minimum. DOE and contractors shall continually review their explosives operations with the aim of achieving further refinements and improvements in safety practices and protective features. This manual describes the Department's explosive safety requirements applicable to operations involving the development, testing, handling, and processing of explosives or assemblies containing explosives. It is intended to reflect the state-of-the-art in explosives safety. ...

1990-05-01

277

Design of a propulsion system with double-layer power capacitors and soft-switched converters for a hybrid automobile  

Energy Technology Data Exchange (ETDEWEB)

This thesis examines the design of a propulsion system for a series hybrid vehicle and includes the study of an energy storage unit using double-layer capacitors and a lightweight soft-switched converter system, and two new components in series hybrid vehicles. The development of environmentally sustainable vehicles is more urgent now given the fact that pollution levels are ever increasing. No electric vehicle has yet been developed that can compete with a normal vehicle based only on internal combustion engines. The dilemma lies in the difficulty of storing the amount of energy needed and supply it a high power levels. An attractive and viable option to reducing pollution and maintaining good performance may lie in hybrid electric-powered vehicles. The double-layer power capacitors are an interesting option because of their high power density and long lifetime. The devices are new and assembling large energy storage units ...

2001-07-01

278

Transition-metal dimers and physical limits on magnetic anisotropy  

British Library Electronic Table of Contents (United Kingdom)

Recent advances in nanoscience have raised interest in the minimum bit size required for classical information storage. This bit size is determined by the necessity for bistability with suppressed quantum tunnelling and energy barriers that exceed ambient temperatures. In the case of magnetic information storage, much attention has centred on molecular magnets with bits consisting of about 100 atoms, magnetic uniaxial anisotropy energy barriers of about 50?K and very slow relaxation at low temperatures. Here, we draw attention to the remarkable magnetic properties of some transition-metal dimers, which have energy barriers approaching 500?K with only two atoms. The spin dynamics of these ultrasmall nanomagnets is strongly affected by a Berry phase, which arises from quasi-degen...

2007-01-01

279

Quantitative measurement of elements in a composite, using multienergy gamma-rays  

International Nuclear Information System (INIS)

This study is an attempt to measure the quantities of elements in a composite by irradiating that composite with #gamma#-rays of various energies and detecting the transmitted radiation through the composite. A previous knowledge of the number of the elements and their attenuation coefficients is required. The quantities are calculated by solving the matrix of a linear system of equations. A computer program was developed to select the best combinations of the available energies. Five criteria were established to determine these energy combinations: (i) the determinant of the attenuation coefficient matrix; (ii) the condition number, (iii) the number of times the solution of the matrix leads to acceptable results; (iv) the indicator, (a new concept); (v) the standard deviations of the results. The intended application of this technique in medicine is to measure the bone mineral content of the skeleton. ...

280

High-energy x-ray microscopy techniques for laser-fusion plasma research at the National Ignition Facility  

Energy Technology Data Exchange (ETDEWEB)

Multi-kilo-electron-volt x-ray microscopy will be an important laser-produced plasma diagnostic at future megajoule facilities such as the National Ignition Facility (NIF). However, laser energies and plasma characteristics imply that x-ray microscopy will be more challenging at NIF than at existing facilities. We use analytical estimates and numerical ray tracing to investigate several instrumentation options in detail, and we conclude that near-normal-incidence single spherical or toroidal crystals may offer the best general solution for high-energy x-ray microscopy at NIF and similar large facilities. Apertured Kirkpatrick{endash}Baez microscopes using multilayer mirrors may also be good options, particularly for applications requiring one-dimensional imaging over narrow fields of view. {copyright} 1998 Optical Society of America

1998-04-01

281

Heat loss from an open cavity  

Energy Technology Data Exchange (ETDEWEB)

Cavity type receivers are used extensively in concentrating solar thermal energy collecting systems. The Solar Total Energy Project (STEP) in Shenandoah, Georgia is a large scale field test for the collection of solar thermal energy. The STEP experiment consists of a large field array of solar collectors used to supplement the process steam, cooling and other electrical power requirements of an adjacent knitwear manufacturing facility. The purpose of the tests, conducted for this study, was to isolate and quantify the radiative, conductive, and convective components of total heat loss, and to determine the effects of operating temperature, receiver angle, and aperture size on cavity heat loss. An analytical model for radiative heat loss was developed and compared with two other methods used to determine radiative heat loss. A proposed convective heat loss correlation, including effects of aperture size, ...

1995-12-01

282

From smart meter to multifuctional energy saving system with RF lon waves. Added services create acceptance and customer benefit; Mit Langwelle vom Smart Meter zum multifunktionalen Energiesparsystem. Zusatzdienste schaffen Akzeptanz und Kundennutzen  

Energy Technology Data Exchange (ETDEWEB)

Smart metering is required by the EU and will be implemented in Germany during the next few years, but customers are not much interested in ''intelligent meters''. Displays and information services may ensure higher acceptance and additional use and provide an incentive for saving energy. In a pilot programme in BAvaria, Eon tested the customers' reaction to such a system. Smart metering technology and long-wave services were combined into an overall system that helps customers save energy. (orig.)

2009-03-16

283

Energy absorbers used against impact loading  

International Nuclear Information System (INIS)

In the WWER-440 reactor the primary piping consists of six horizontal loops going radially from the pressure vessel, each loop having a horizontal steam generator. In this reactor type the relatively long primary piping with many curved sections requires special attention in order to successfully eliminate the consequences of the design basis accident. Emergency supports are located in appropriate places to restrict the movements of the pipe. Under normal conditions there is a gap of some centimeters between the pipe and a support so that in the pipe can be deformed freely under changing loads. This paper deals with those energy-absorbing structures used at the Loviisa Nuclear Power Plant for protection against impact loading. Places and circumstances where energy-absorbing structures are employed are specified. Development and design of impact absorber elements are discussed and impact tests are described. (Auth.).

1975-09-08

284

Electricity generation from rice husk in Indian rice mills: potential and financial viability  

Energy Technology Data Exchange (ETDEWEB)

Rice husk generated as a by-product of rice processing is an important energy resource. The availability of this resource in India has been assessed and the technologies for exploitation of its energy potential in rice processing industry discussed. Nomographs have been developed for estimation of the husk required to meet the energy demand of parboiling, drying and milling operations. The unit cost of electricity using rice husk gasifier-based power generation systems has been calculated and its financial feasibility assessed in comparison with utility-supplied and diesel-generated electricity. With the cost and efficiency data assumed here, the unit cost of electricity produced by rice husk gasifier-dual fuel engine-generator system varies between Rs 2/kWh and Rs 7/kWh. (author)

1996-10-01

285

Electricity generation from rice husk in Indian rice mills: potential and financial viability  

Energy Technology Data Exchange (ETDEWEB)

Rice husk generated as a by-product of rice processing is an important energy resource. The availability of this resource in India has been assessed and the technologies for exploitation of its energy potential in the rice processing industry discussed. Nomographs have been developed for estimation of the husk required to meet the energy of parboiling, drying and milling operations. The unit cost of electricity using rice husk gasifier-based power generation systems has been calculated and its financial feasibility assessed in comparison with utility-supplied and diesel-generated electricity. With the cost and efficiency data assumed here, the unit cost of electricity produced by rice husk gasifier-dual fuel engine-generator system varies between Rs 2/kWh and Rs 7/kWh. (35 Rs approximates to SUS 1.). (author)

1998-12-31

286

Development of a portable thermophotovoltaic power generator  

Energy Technology Data Exchange (ETDEWEB)

A 150 Watt thermophotovoltaic (TPV) power generator is being developed. The technical approach taken in the design focused on optimizing the integrated performance of the primary subsystems in order to yield high energy conversion efficiency and cost effectiveness. An important aspect of the approach is the use of a selective emitter radiating to a bandgap matched photovoltaic array to minimize thermal and optical recuperation requirements, as well as the non-recoverable heat losses. For the initial prototype system, fibrous ytterbia emitters radiating in a band centered at 980 nm are matched with high efficiency silicon photoconverters. The integrated system includes a dielectric stack filter for optical energy recovery and a ceramic recuperator for thermal energy recovery. The system has been operated with air preheat temperatures up to 1350K. The design of the system and development status are ...

1997-03-01

287

Approaches to the modelling of energy utilisation in product life cycles  

Energy Technology Data Exchange (ETDEWEB)

The paper considers research carried out on the topic of life cycle (LC) modelling of industrial processes with emphasis upon energy utilisation and gaseous emissions. The aim of the work is to investigate existing LC assessment codes, in particular for their outputs and decision making potential, and to develop the characteristics of new software as appropriate. The paper focuses on a comparison of two methods for LC modelling: use of ''SimaPro 5'' with ECO-indicators and logical-information modelling. The considered approaches require attention to dynamic modelling having features for decision making; for example, in areas of costs, sensitivity analysis and optimisation of LC process parameters to economically reduce the total environmental load. Brick making is chosen as an energy intensive process for model application. (orig.)

2006-05-15

288

Daily cone-beam computed tomography used to determine tumour shrinkage and localisation in lung cancer patients  

Energy Technology Data Exchange (ETDEWEB)

Purpose/Objective. Daily Cone-beam computed tomography (CBCT) in room imaging is used to determine tumour shrinkage during a full radiotherapy (RT) course. In addition, relative interfractional tumour and lymph node motion is determined for each RT fraction. Material and methods. From November 2009 to March 2010, 20 consecutive lung cancer patients (14 NSCLC, 6 SCLC) were followed with daily CBCT during RT. The gross tumour volume for lung tumour (GTV-t) was visible in all daily CBCT scans and was delineated at the beginning, at the tenth and the 20th fraction, and at the end of treatment. Whenever visible, the gross tumour volume for lymph nodes (GTV-n) was also delineated. The GTV-t and GTV-n volumes were determined. All patients were setup according to an online bony anatomy match. Retrospectively, matching based on the internal target volume (ITV), the GTV-t or the GTV-n was performed. Results. In eight patients, we ...

2010-10-15

289

Verification of safety critical software  

Energy Technology Data Exchange (ETDEWEB)

To assure quality of safety critical software, software should be developed in accordance with software development procedures and rigorous software verification and validation should be performed. Software verification is the formal act of reviewing, testing of checking, and documenting whether software components comply with the specified requirements for a particular stage of the development phase[1]. New software verification methodology was developed and was applied to the Shutdown System No. 1 and 2 (SDS1,2) for Wolsung 2,3 and 4 nuclear power plants by Korea Atomic Energy Research Institute(KAERI) and Atomic Energy of Canada Limited(AECL) in order to satisfy new regulation requirements of Atomic Energy Control Boars(AECB). Software verification methodology applied to SDS1 for Wolsung 2,3 and 4 project will be described in this paper. Some errors were found by this methodology ...

1996-12-01

290

Verification of safety critical software  

International Nuclear Information System (INIS)

To assure quality of safety critical software, software should be developed in accordance with software development procedures and rigorous software verification and validation should be performed. Software verification is the formal act of reviewing, testing of checking, and documenting whether software components comply with the specified requirements for a particular stage of the development phase[1]. New software verification methodology was developed and was applied to the Shutdown System No. 1 and 2 (SDS1,2) for Wolsung 2,3 and 4 nuclear power plants by Korea Atomic Energy Research Institute(KAERI) and Atomic Energy of Canada Limited(AECL) in order to satisfy new regulation requirements of Atomic Energy Control Boars(AECB). Software verification methodology applied to SDS1 for Wolsung 2,3 and 4 project will be described in this paper. Some errors were found by this methodology ...

1996-01-01

291

Standards for transport and storage components established by The Atomic Energy Society of Japan and The Japan Society of Mechanical Engineers  

Energy Technology Data Exchange (ETDEWEB)

Since June 1997 the standards/specifications and inspection/certification of various products in Japan have been reviewed by Ministries and Agencies, with the aim of reducing direct government intervention to a necessary minimum and creating a free and fair socio-economic system that is fully opened to the international community and based on the rules of self-responsibility and market principles. Reflecting this policy the administrative regulations which prescribe technical standards as specific requirements have been revised by degrees into performance prescriptions. Detailed provisions in ordinances and notices have been abolished gradually to utilize voluntary standards and rules. In the nuclear energy field voluntary standards are being developed to make up statutory performance requirements by the Atomic Energy Society of Japan (AESJ) and the Japan Society of Mechanical Engineers (JSME) together ...

2004-07-01

292

Liberalisation of energy markets and integration of information technology; Energiemarkt-Liberalisierung und IT-Integration. Erfolgsfaktoren und Projekterfahrungen  

Energy Technology Data Exchange (ETDEWEB)

The liberalisation of the energy markets requires completely new demands to the information processing procedure of energy supply enterprises. These requirements are to be understood as chances for strengthening of the terms of competition. In the following contribution to this subject the actual status of the concept as converted by the Electricity Supply Company of Halle (Saale) including their departments of district heating, gas and electricity supply will be presented. This concept are comprising all experiences as gathered so far as well as intended further actions to be executed. (orig.) [German] Die Liberalisierung der Energiemaerkte stellt fuer Versorgungsunternehmen voellig neue Anforderungen an die Informationsverarbeitung. Diese Anforderungen sind als Chancen zur Staerkung der Wettbewerbsfaehigkeit zu verstehen. Die Verfasser erlaeutern den aktuellen Stand des in der EVH GmbH Halle (Saale) ...

2003-05-19

293

High efficiency direct thermal to electric energy conversion from radioisotope decay using selective emitters and spectrally tuned solar cells  

International Nuclear Information System (INIS)

Thermophotovoltaic (TPV) systems are attractive possibilities for direct thermal-to-electric energy conversion, but have typically required the use of black body radiators operating at high temperatures. Recent advances in both the understanding and performance of solid rare-earth oxide selective emitters make possible the use of TPV at temperatures as low as 1200K. Both selective emitter and filter system TPV systems are feasible. However, requirements on the filter system are severe in order to attain high efficiency. A thin-film of a rare-earth oxide is one method for producing an efficient, rugged selective emitter. An efficiency of 0.14 and power density of 9.2 W/KG at 1200K is calculated for a hypothetical thin-film neodymia (Nd2O3) selective emitter TPV system that uses radioisotope decay as the thermal energy source.

1993-08-23

294

Transportation fuels and engines for optimum energy utilization: An assessment of energy consumption from resources through end use: Final report, Volume 1  

Energy Technology Data Exchange (ETDEWEB)

This report presents an assessment of the potential energy savings that could accrue from the use of alternative fuels in future transportation engines. Alternative fuels are defined in this study as hydrocarbon fuels which possess characteristics that assure user safety and satisfaction, but require less energy to produce than conventional specification fuels produced from the same resource. In particular, the energy requirements for producing such fuels from domestic coal and oil shale resources are examined from the standpoint of their adaptability to engine types having a high potential for achieving significant efficiency gains over existing transportation engines. Incentives for specific types of engine development are identified in terms of energy savings above those obtainable with current specification fuels. While engine research and development ...

1985-08-01

295

Hydrogen in European and global energy systems  

Energy Technology Data Exchange (ETDEWEB)

Interest in energy systems based on hydrogen is growing rapidly. Countries including the USA, Japan and Germany have been active in this area for a number of years, but recently a large number of new countries have appeared on the hydrogen scene. These include Australia, Romanla, Greece, China and India. The main reason for this renewed interest is that a future hydrogen society may be one of the solutions to the two major challenges facing the future global economy: climate change and security of energy supply. Both these challenges require the development of new, highly-efficient energy technologies that are either carbon-neutral or emit only small amounts of carbon dioxide. While demand for oil is expected to keep on growing, the supply of oil is forecasted to peak within the next 10-20 years. In a longer time-perspective, there is thus a strong need for new fuels, especially in the transport sector. ...

2004-10-01

296

Characterization of carbon-based electrochemical capacitor technology from Maxwell Energy Products, Inc.  

Energy Technology Data Exchange (ETDEWEB)

The electrochemical capacitor devices described in this report were deliverables from the US Department of Energy--Idaho Operations Office (DOE-ID) Contract No. DE-AC07-92ID13404 as part of the US Department of Energy`s (DOE) High Power Energy Storage Program. The Idaho national Engineering and Environmental Laboratory (INEEL) has responsibility for technical management, testing, and evaluation of high-power batteries and electrochemical capacitors under this Program. The DOE has developed various electrochemical capacitors as candidate power assist devices for the Partnership for a New Generation of Vehicles (PNGV) fast response engine requirement. This contract with Maxwell Energy Products, Inc. (Maxwell) was intended to develop a high-energy-density, high-power-density ultracapacitor that is capable of load leveling batteries in electric vehicles. The ...

1998-04-01

297

Utility applications program. Annual report for 1981  

Energy Technology Data Exchange (ETDEWEB)

The purpose of the Utility Applications Program is to provide information and assistance to interested utilities on central station energy storage systems. Compressed air and underground pumped hydroelectric energy storage are the primary technical focus. Smaller utilities are the primary targets of this program, as they may not have resources to track and utilize new energy conservation developments. The program, initiated during this year-long period, consists of a series of tasks integrating and supporting energy storage implementation. Program management and technical coordination activities monitor the wide range of research ongoing both under government support and in industry and provide a locus for dissemination of results. Recently completed DOE demonstration studies provide the central data base and the DOE CAES and UPH Technology Program activities provide another major resource. In addition ...

1982-06-01

298

Two-phase flow regime management for in-space power rejection management -- Feasibility study  

Energy Technology Data Exchange (ETDEWEB)

A novel two-phase flow management process useful for active thermal power rejection in space is introduced. The process serves as a condenser in a Rankine cycle and is applicable for thermal energy management needs in low gravity environments. Benefit is derived from the ability to utilize the high specific energy transport capability of two-phase flow, while not requiring mass-intensive solutions nor complex control strategies to maintain design energy balance integrity. Initial design calculations for a hypothetical space vapor cycle demonstration experiment were done and a steady-state computer model of the novel condensing process was created and used to evaluate its potential to maintain the design energy balance of the experiment. The experiment (approximately 28 kg) was a supercritical organic thermal loop operating between 500 and 400 Kelvin at a mass flow of 1 grain per ...

1995-12-31

299

Simulation of a Standing-Wave Free-Electron Laser  

Energy Technology Data Exchange (ETDEWEB)

The standing-wave free-electron laser (FEL) differs from a conventional linear-wiggler microwave FEL in using irises along the wiggler to form a series of standing-wave cavities and in reaccelerating the beam between cavities to maintain the average energy. The device has been proposed for use in a two-beam accelerator (TBA) because microwave power can be extracted more effectively than from a traveling-wave FEL. The standing-wave FEL is modeled in the continuum limit by a set of equations describing the coupling of a one-dimensional beam to a TE{sub 01} rectangular-waveguide mode. Analytic calculations and numerical simulations are used to determine the time variation of the reacceleration field and the prebunching required so that the final microwave energy is the same in all cavities. The microwave energy and phase are found to be insensitive to modest spreads in the beam energy ...

1990-09-01

300

Proposal for a High Energy Nuclear Database  

Energy Technology Data Exchange (ETDEWEB)

The authors propose to develop a high-energy heavy-ion experimental database and make it accessible to the scientific community through an on-line interface. This database will be searchable and cross-indexed with relevant publications, including published detector descriptions. Since this database will be a community resource, it requires the high-energy nuclear physics community's financial and manpower support. This database should eventually contain all published data from Bevalac, AGS and SPS to RHIC and CERN-LHC energies, proton-proton to nucleus-nucleus collisions as well as other relevant systems, and all measured observables. Such a database would have tremendous scientific payoff as it makes systematic studies easier and allows simpler benchmarking of theoretical models to a broad range of old and new experiments. Furthermore, there is a growing need for compilations of ...

2005-03-31

301

IECEC '87; Proceedings of the Twenty-second Intersociety Energy Conversion Engineering Conference, Philadelphia, PA, Aug. 10-14, 1987. Volumes 1, 2, 3, and 4  

International Nuclear Information System (INIS)

Papers are presented on space power requirements and issues, space photovoltaic systems, space solar dynamic systems, space thermal systems, manned and unmanned space power systems, thermionics, and thermoelectrics. Also considered are high power devices for space power systems, high power conversion for space power systems, 1-10 kWe nuclear space power sources, 100-kW class nuclear power concepts, space reactor safety, and multimegawatt space nuclear power systems. Other topics include space power systems automation, space kilovolt technology, space power electronics, space lithium and nickel-cadmium batteries, lithium sodium storage, and space fuel cells. Papers are also presented on space nickel hydrogen batteries, alternative energy concepts and fuels, fuel cell technology, flow batteries, high-temperature batteries, energy conservation, battery energy storage, thermal energy ...

1987-08-10

302

Hemispheres-in-cell geometry to predict colloid deposition in porous media.  

Science.gov (United States)

A "hemispheres-in-cell" geometry is provided for prediction of colloid retention during transport in porous media. This new geometry preserves the utilities provided in the Happel sphere-in-cell geometry; namely, the ability to predict deposition for a range of porosities, and representation of the influence of neighboring collectors on the fluid flow field. The new geometry, which includes grain to grain contact, is justified by the eventual goal of predicting colloid deposition in the presence of energy barriers, which has been shown in previous literature to involve deposition within grain to grain contacts for colloid:collector ratios greater than approximately 0.005. In order to serve as a platform for predicting deposition in the presence of energy barriers, the model must be shown capable of quantitatively predicting deposition in the absence of energy barriers, which is a requirement that was ...

2009-11-15

303

Delayed-neutron energy spectra following thermal-neutron-induced fission of Pu-239  

Energy Technology Data Exchange (ETDEWEB)

Delayed-neutron (DN) energy spectra following thermal neutron induced fission of /sup 239/Pu as a function of time after fission have been measured, using the beta-neutron time-of-flight (TOF) spectrometer at the University of Lowell. Thermal/epithermal neutrons were produced on the 5.5-MV Van de Graaff accelerator using the /sup 7/Li(p,n)/sup 7/Be reaction. Time spectra over the neutron energy range of 0.01-4.0 MeV were measured for seven different time intervals after fission, each interval containing varying contributions from the six delayed neutrons groups. The DN energy spectra following induced thermal fission of /sup 239/Pu are compared to those resulting from induced thermal fission of /sup 235/U for each of the seven delay time intervals. Decomposition of the measured spectra into six-group DN spectra was accomplished employing an iterative least-squares method, incorporating a constraint ...

1987-01-01

304

Collisional cooling of negative-ion beams  

Energy Technology Data Exchange (ETDEWEB)

Studies have been conducted to determine the feasibility of using collisional cooling for reducing emittances and energy spreads in negative-ion beams to levels commensurate with effective isobaric purification with conventional high-resolution electromagnetic isobar separators as required for use at the Holifield Radioactive Ion Beam Facility (HRIBF). We have designed a gas-filled radio frequency quadrupole ion cooler equipped with provisions for retarding energetic negative-ion beams to energies below thresholds for electron detachment at injection and for re-acceleration to initial energies after the cooling process. The device has been used to cool several ion beams with initial energy spreads, {delta}E>10 eV to final energy spreads, {delta}E{approx}2 eV FWHM, including O{sup -} and F{sup -}. Overall transmission efficiencies of {approx}14% for F{sup ...

2002-01-01

305

Progress toward an optimized hydrogen series hybrid engine  

Energy Technology Data Exchange (ETDEWEB)

The design considerations and computational fluid dynamics (CFD) modeling of a high efficiency, low emissions, hydrogen-fueled engine for use as the prime mover of a series hybrid automobile is described. The series hybrid automobile uses the engine to generate electrical energy via a lightweight generator, the electrical energy is stored in a power peaking device (like a flywheel or ultracapacitor) and used as required to meet the tractive drive requirements (plus accessory loads) through an electrical motor. The engine/generator is stopped whenever the energy storage device is fully charged. Engine power output required was determined with a vehicle simulation code to be 15 to 20 kW steady state with peak output of 40 to 45 kW for hill climb. Combustion chamber and engine geometry were determined from a critical review of the hydrogen engine experiments in the ...

1995-06-01

306

Coilgun Launcher for Nanosatellites  

Energy Technology Data Exchange (ETDEWEB)

Nanosatellite space launches could significantly benefit from an electrically powered launch complex, based on an electromagnetic coil launcher. This paper presents results of studies to estimate the required launcher parameters and some fixed facility issues. This study is based on electromagnetic launch, or electromagnetic gun technology, which is constrained to a coaxial geometry to take advantage of the efficiency of closely-coupled coils. A baseline configuration for analysis considers a payload mass of 10 kg, launch velocity of 6 km/s, a second stage solid booster for orbital insertion, and a payload fraction of about 0.1. The launch facility is envisioned as an inclined track, 1-2 km in length, mounted on a hillside at 25 degrees aimed in the orbital inclination of interest. The launcher energy and power requirements fall in the range of 2000 MJ and 2 MW electric. This energy would be supplied by ...

1999-03-23

307

Proposal of procedures to prevent errors in radiotherapy based in learned lessons of accidental expositions; Proposta de procedimentos para evitar erros em radioterapia baseados em licoes aprendidas de exposicoes acidentais  

Energy Technology Data Exchange (ETDEWEB)

In order to consider some procedures to prevent errors in radiotherapy based in learned lessons of accidental expositions and in accordance with information contained in international reports elaborated by International Atomic Energy Agency (IAEA) and of the data base availability by the European group Radiation Oncology Safety Information System (ROSIS) on the events, a research of the occurred errors was performed. For the evaluation of the incidents a data base based in the ROSIS and added plus a parameter was created 'type of error'. All the stored data make possible the evaluation of the 839 incidents in terms of frequency of the type of error, the process of detention, the number of reached patients and the degree of severity. Of the 50 types of found errors, the type of error more frequently was 'incorrect treatment coordinate', confirmed with the data of literature and representing 28,96 por cent of the total of the ...

2007-07-01

308

SE and I content in military total diet  

International Nuclear Information System (INIS)

Selenium and iodine are trace elements that play an important role in health of man and animals. Concerning supply of both elements it is important to meet nutritional needs. According to discoveries selenium is a part of an active group of glutathione peroxidase enzyme. It prevents necrotic changes in liver, muscle dystrophy and has impact on growth. Extensive studies on content of selenium in plant and animal origin products were started in the beginning of the seventies in Western Europe (Frankenberger, et al., 1998). The aim of our work was to determine selenium and iodine content in total diets of Slovene military. Slovene military nutrition is based on its own nutritional standards, which determine 200 #mu#g of iodine and 50 #mu#g of selenium in daily diet (Rep. Slovenija Ministrstvo za Obrambo, 1994). To determine if the amounts of both elements meet the standards we have analysed 20 total daily diets from four different barracks within ...

2003-06-10

309

Milk yield and quality in Guernsey cows fed cottonseed cake-based diets partially substituted with baobab (Adansonia digitata L.) seed cake  

British Library Electronic Table of Contents (United Kingdom)

The objective of this study was to determine the effects of partially substituting cottonseed cake with graded levels of baobab (Adansonia digitata L.) seed cake (BSC) on milk yield and quality in Guernsey cows. Sixteen cows in mid-lactation and in their third parity were allocated to diets containing 0% (control), 5%, 10%, and 15% BSC in a completely randomized design. Each cow was given a daily feed ration of 6?kg and a basal diet of soya bean stover ad libitum. There were no differences in daily feed intake (P?>?0.05), but basal intake differed among all treatment groups with cows on the control diet having the highest intake (30???0.34?kg/day). Mean daily milk yield differed (P?P?P?P?P?>?0.05). These results indicate that BSC can substitute soya bean cake in dairy diets, but milk produ...

2011-01-01

310

Photovoltaic performance and long-term stability of dye-sensitized mesoscopic solar cells  

International Nuclear Information System (INIS)

The efficiency of electric power generation by dye-sensitized mesoscopic photovoltaic cells has been progressing steadily over the last years reaching now 11% in full sunlight. An important question for practical applications concerns the stability of these devices under prolonged exposure to light or heat. Strikingly stable operation can be obtained by judicious selection of the sensitizer, electrolyte and sealant rendering feasible a service life of at least 20 years under normal outdoor conditions. The sensitizer playing a central role in the light energy conversion process, we analyze the kinetic requirements for it to sustain the required one hundred million turnovers. We also review recent results on the use of self-assembled monolayers of amphiphilic sensitizers and co-adsorbents to enhance the thermal robustness of the device. (author)

2004-07-04

311

Facilities evaluation report  

Energy Technology Data Exchange (ETDEWEB)

The Buried Waste Integrated Demonstration (BWID) is a program of the Department of Energy (DOE) Office of Technology Development whose mission is to evaluate different new and existing technologies and determine how well they address DOE community waste remediation problems. Twenty-three Technical Task Plans (TTPs) have been identified to support this mission during FY-92; 10 of these have identified some support requirements when demonstrations take place. Section 1 of this report describes the tasks supported by BWID, determines if a technical demonstration is proposed, and if so, identifies the support requirements requested by the TTP Principal Investigators. Section 2 of this report is an evaluation identifying facility characteristics of existing Idaho National Engineering Laboratory (INEL) facilities that may be considered for use in BWID technology demonstration activities.

1992-04-01

312

Economic thickness for industrial insulation  

Energy Technology Data Exchange (ETDEWEB)

This manual is presented in 8 chapters plus appendices. Chapters 1 and 2 are included as background information. The economic insulation thickness is found using the following chapters: Chapter 3, cost of energy (heat and refrigeration); Chapter 4, cost of insulation, and Chapter 5, economic thickness determination. Each of these chapters contains a worksheet, which provides a step-by-step procedure for solving the problem. Nomographs are included in each section for simplifying the required calculations. For subambient temperature systems, the economic insulation thickness calculated with Chapters 3 to 5 should be compared to the thickness required to prevent condensation (sweating), as calculated with Chapter 6. Chapter 7 presents the procedure for calculating economic insulation for retrofit situations. Sample problems are included in Chapter 8.

1983-01-01

313

A study of solar-powered, high-altitude unmanned aerial vehicles  

British Library Electronic Table of Contents (United Kingdom)

Purpose ? Aims to present a methodology for analysing a solar-electric, high-altitude, long-endurance, unmanned aircraft. Design/methodology/approach ? The study focuses on the aerodynamics, flight performance and power requirements of a heavier-than-air, solar-electric, HALE UAV. The methodology is founded on using an analytical approach to determine the power required to undertake various flight manoeuvres. An analytical approach is also undertaken in determining the intensity of the solar radiation available to the aircraft. Finally to demonstrate the methodology, a HALE concept was generated and evaluated. Findings ? When using estimates of current solar-electric propulsion and energy conversion efficiencies, the HALE concept was only able to sustain year round, level flight up to lati...

2006-01-01

314

A Review of the IAEA Vulnerability Assessment Level Scheme: Applicabiliy to DTRA and DOE Programs in the FSU  

Energy Technology Data Exchange (ETDEWEB)

The International Atomic Energy Agency (IAEA) plans to use the Common Criteria, as the tool for developing graded and measurable evaluation criteria for information technology (IT) in safeguards systems in facilities subject to IAEA inspection. In their draft paper [ITSECSES] the IAEA defines a three-tiered Vulnerability Assessment Level (VAL) scheme. Each increased VAL level (1-3) defines additional and more stringent security and security-related requirements for the system developer, the system evaluator (assessor or authenticator), and for the IAEA. When all parties meet all requirements for a particular VAL level, IAEA has a measurable degree of confidence in the secure and proper operation of an IT system.

2001-12-06

315

Evaluation of impacts on wetlands: do NEPA analyses integrate wetland protection requirements  

Energy Technology Data Exchange (ETDEWEB)

The impacts of federal projects on wetlands should be included in documents prepared to comply with the National Environmental Policy Act (NEPA). NEPA assessments of impacts on wetlands are often related to requirements of other laws, regulations, and executive orders, such as permitting requirements under Section 404 of the Clean Water Act and those contained in Executive Order 11990, Protection of Wetlands. This paper reviews recent NEPA environmental impact statements that contained assessments of impacts on wetlands or that involved projects likely to affect wetlands. It covers documents prepared by several federal agencies, including the Army Corps of Engineers, Department of Energy, Federal Highway Administration, Soil Conservation Service, and Tennessee Valley Authority. The extent and depth of analyses of wetlands issues was found to be highly variable, both within and among agencies. Most analyses did not provide ...

1991-01-01

316

State of the energy in Lebanon  

International Nuclear Information System (INIS)

The article describes the state of the energy in Lebanon. In 1996, Lebanon consumed 4647 Ktoe as a primary energy. 97% of this energy is imported mainly polluting oil products: 1623 Ktons fuel-oil, 1379 Ktons gasoline, 930 Ktons diesel, 200 Ktons coal, 124 Ktons LPG, 107 Ktons jet-fuel/Kerosene, 109 Ktons Asphaltic products. The remaining 3% of the energy consumption is renewable energy. As for production, the state owns two refineries which are not used anymore. The year 2000 plan includes an expansion project for the Tripoli refinery and an alternative plan for the Zahrani refinery. These refineries require a total investment in order to reach a production capacity of 50000 barrels a day. The article is a description of the pollution type sources and location in Lebanon. The combustion of the total energy produces yearly more than 15 Ktons ...

1998-04-01

317

Energy consumption by the private and commercial vehicles, and by public transport facilities, which comprise urban street traffic; Energiforbrug ved individuel og kollektiv trafik i bygader  

Energy Technology Data Exchange (ETDEWEB)

The aim was to compare the energy consumption by private and commercial vehicles with that of public transport facilities constituting urban street traffic, and to evaluate the influence of various traffic related plans such as green waves (where cars are able to drive through the town with relatively few accelerations and braking) streets with lower speed limits and special lanes and priorities for buses. The traffic pattern in four Copenhagen streets (Jagtvej, Soelvgade, Bredgade and Strandvejen) were measured and analyzed both in, and not in, the rush hour, and a special model was used to calculate the energy consumption. The model defines degree of acceleration and slow-down and speed when calculating energy consumption with regard to various driving patterns. It also calculates carbon dioxide emission. It was found that energy consumption decreased with increasing driving speed at 10-60 km/h for ...

1993-03-01

318

Energy consumption by the private and commercial vehicles, and by public transport facilities, which comprise urban street traffic. Energiforbrug ved individuel og kollektiv trafik i bygader  

Energy Technology Data Exchange (ETDEWEB)

The aim was to compare the energy consumption by private and commercial vehicles with that of public transport facilities constituting urban street traffic, and to evaluate the influence of various traffic related plans such as green waves (where cars are able to drive through the town with relatively few accelerations and braking) streets with lower speed limits and special lanes and priorities for buses. The traffic pattern in four Copenhagen streets (Jagtvej, Soelvgade, Bredgade and Strandvejen) were measured and analyzed both in, and not in, the rush hour, and a special model was used to calculate the energy consumption. The model defines degree of acceleration and slow-down and speed when calculating energy consumption with regard to various driving patterns. It also calculates carbon dioxide emission. It was found that energy consumption decreased with increasing driving speed at 10-60 km/h for ...

1993-03-01

319

The use of long-term and seasonal trends of elemental compounds as an aid to the identification of sources of airborne pollutants  

Energy Technology Data Exchange (ETDEWEB)

New York City data indicate that seasonal and annual variations in dispersion-normalized air pollutant concentrations appear to accurately reflect changes in source emission patterns. The normalized concentrations make it possible to observe the impact of regulatory changes on ambient air quality without these impacts being obscured by meteorological fluctuations. It is found that numerical modeling techniques and regression analysis can be powerful tools for extracting information from large sets of air quality data. The use of differential, as opposed to absolute, pollutant concentration values will reduce artifact correlations caused by seasonal, weekly, or daily meteorological fluctuations and will permit more accurate estimation of the regression coefficients. This technique was successfully applied to a set of daily pollution measurements whose absolute concentrations were found not to yield a statistically significant fit by multiple ...

1980-01-01

320

The use of long-term and seasonal trends of elemental compounds as an aid to the identification of sources of airborne pollutants  

International Nuclear Information System (INIS)

New York City data indicate that seasonal and annual variations in dispersion-normalized air pollutant concentrations appear to accurately reflect changes in source emission patterns. The normalized concentrations make it possible to observe the impact of regulatory changes on ambient air quality without these impacts being obscured by meteorological fluctuations. It is found that numerical modeling techniques and regression analysis can be powerful tools for extracting information from large sets of air quality data. The use of differential, as opposed to absolute, pollutant concentration values will reduce artifact correlations caused by seasonal, weekly, or daily meteorological fluctuations and will permit more accurate estimation of the regression coefficients. This technique was successfully applied to a set of daily pollution measurements whose absolute concentrations were found not to yield a statistically significant fit by multiple ...

321

Solar-Geophysical Data Number 438, February 1981. Part 1 (prompt reports). Data for January 1981, December 1980 and late data  

Energy Technology Data Exchange (ETDEWEB)

Contents include: index for 1970-1980; January 1981 data -- alert periods, daily solar indices, solar flares, solar radio emission, coronal holes, inferred interplanetary magnetic field polarities, mean solar magnetic field, spacecraft observations, December 1980 data -- daily solar-activity centers, sudden ionospheric disturbances, spacecraft observations, solar radio emission, cosmic rays, geomagnetic indices, radio-propagation indices; late data -- solar radio emission November, December 1980, spacecraft observations November 1980, cosmic rays, Huancayo Oct 1980 -- climax, alert, Deep River Nov 1980.

1981-02-01

322

Randomised, placebo-controlled trial to evaluate co-trimoxazole to reduce mortality and morbidity in HIV-infected post-natal women in Zambia (TOPAZ)  

British Library Electronic Table of Contents (United Kingdom)

Summary Objective- To evaluate the role of prophylactic trimethoprim-sulfamethoxazole (co-trimoxazole) antibacterial prophylaxis in reducing morbidity and mortality in HIV-infected post-natal women in southern Africa. Methods- Double-blind placebo-controlled trial. HIV-infected women with WHO stage 2 or 3 HIV disease who had recently delivered in the Department of Obstetrics and Gynaecology at the University Teaching Hospital, Lusaka, Zambia were randomised to receive daily co-trimoxazole (cotox) or matched placebo daily for the duration of the trial. Participants were followed up for a minimum of 1-year. Primary outcome measures were mortality from any cause or hospital admission and serious adverse events. Results- Of 600 women randomised, follow-up information was available from 355 (18...

2011-01-01

323

Radiostrontium in milk and tap water  

International Nuclear Information System (INIS)

Analysis of Sr-90 in milk and tap water has been conducted in New York City since 1954. The milk sample analyzed is a monthly composite of pasteurized milk purchased daily at retail stores. The monthly Sr-90 to calcium ratios for New York City since the inception of the sampling progam in 1954 through 1981 are tabulated. Samples of New York City tap water are taken daily so that by the end of the month, approximately 100 liters have been collected. Data on Sr-90 since the inception of the program are presented. The available Cs-137 data expressed as the Cs-137 to Sr-90 ratio are given. A graphical presentation of the New York City Sr-90 data is also shown.

1982-05-01

324

One-year prospective follow-up of pharmacological treatment in children with attention-deficit/hyperactivity disorder  

British Library Electronic Table of Contents (United Kingdom)

Objectives To delineate the safety and tolerability profile of methylphenidate and atomoxetine in children and adolescents with attention deficit hyperactivity disorder (ADHD) monitored for more than 1?year. Design A cohort study analyzing data from the national ADHD register on patients from the Lombardy Region treated with MPH or atomoxetine. Participants A total of 229 children (median age 11?years, range 6?17), enrolled in 15 regional centers between June 2007 and May 2010. Results The prevalence rate of pharmacological treatment for ADHD was 0.23%, whereas the estimated ADHD prevalence in the population was 0.95%. In total, 73.8% of patients had been treated with atomoxetine (10?90?mg daily) or MPH (10?75?mg daily); 22% of patients also received an additional psychotropic drug. Of the...

2011-01-01

325

Estimation of "1"3"7Cs body burden in Japanese, 2  

International Nuclear Information System (INIS)

The biological half-life of "1"3"7Cs in the total body of human subjects was determined in 23 individuals of Japanese male adult in their normal works by measuring amount of "1"3"7Cs in both their total body and daily urine in the same period. For the group, the value was determined by averaging the half-lives for individuals, by comparing the mean body burden and the mean daily urinary excretion, or by applying a curve fitting method to the body burden estimate. The biological half-life averaged 86 days, ranging from 50 to 161 days. The averages of the biological half-lives for the group were 83, 87 and 82 days in the different periods of observation. By the curve fitting method, 85 days was found for the group. The biological half-life for the individuals depended on both body weight and age, to a lesser extent, of the subjects. (author).

326

Comparison of Effectiveness and Safety of Ranolazine Versus Amiodarone for Preventing Atrial Fibrillation After Coronary Artery Bypass Grafting  

British Library Electronic Table of Contents (United Kingdom)

Atrial fibrillation (AF) is common after coronary artery bypass grafting (CABG) and increases the morbidity and cost. Amiodarone reduces AF after CABG. Ranolazine, an antianginal agent, also prolongs atrial refractoriness and inhibits after depolarizations and triggered activity; effects that could decrease AF after CABG. The present study compared amiodarone versus ranolazine for the prevention of AF after CABG. A retrospective cohort study of patients undergoing CABG at Aspirus Hospital from June 2008 to April 2010. The patients received either amiodarone (400 mg preoperatively followed by 200 mg twice daily for 10 to 14 days) or ranolazine (1,500 mg preoperatively followed by 1,000 mg twice daily for 10 to 14 days). The primary end point was any identified AF after CABG. A total of 393 ...

2011-01-01

327

Comparative toxicity in rats vs hamsters of inhaled radon daughters with and without uranium ore dust  

International Nuclear Information System (INIS)

Simultaneous exposures of rats and hamsters to inhaled radon daughters, with and without uranium ore dust, were performed daily for five months. Pulmonary pathology developing in 6 to 13 mo after cessation of daily exposures included interstitial fibrosis, emphysema, epithelial hyperplasia, squamous metaplasia, and malignant neoplasia. Rats showed a greater variety and more severe response to these uranium mine inhalation exposures than did hamsters. Inhalation of radon daughters with uranium ore dust displayed the site of greatest damage, including squamous carcinoma, from the nasopharynx to the lungs. Sixty percent of the rats exposed to radon daughters with ore dust developed primary pulmonary carcinomas, providing an appropriate short-term experimental animal model for investigation of respiratory tract carcinogenesis in uranium miners.

1977-05-01

328

Towards a higher energy efficiency and lower carbon society the European approach and experience  

International Nuclear Information System (INIS)

The use of natural energy sources and their conversion to secondary forms of energy are a crucial base for the development of our society with its continuous change of requirements due to an increase in population and the broadening of the needs in our modern life. As a consequence the consumption of primary energy resources rose drastically worldwide during the last 5 decades in particular in the industrialized regions such as Europe. Parallel in time the increasing awareness of negative effects of fuel dependent pollution on the environment and the introduction of stringent emission control regulations about 3 decades ago initiated extensive development and retrofit activities resulting in the today applied high level state of the art. As an additional challenge the worldwide debate about the potential effects of the emission of the s.c green house gases on the global climate in particular carbon ...

2010-07-26

329

Reducing VMTs through Transit-On-Demand with GPS and satellite communications  

Energy Technology Data Exchange (ETDEWEB)

As a partial solution to the problem of increasing foreign petroleum imports,urban congestion, and air pollution from automobiles, NREL researchers have successfully demonstrated a transportation concept called Transit-On-Demand (TOD). TOD uses the global positioning system (GPS) to locate all vehicles in a fleet, two-way communications between the vehicles and a central computer-server, and advanced dispatching and routing software to control the movement of vehicles within the fleet. Reducing the vehicle-miles-travelled (VMTs) through implementing efficient transportation systems such as TOD, results in less energy being required for transportation and a decrease in the amount of required imported petroleum. Through development of an advanced world wide web site and use of the new Java{trademark} Internet programming language, the demonstration allows visitors to the web site to see updates of vehicle position on a map ...

1996-10-01

330

Natural gas market review 2006 - towards a global gas market  

International Nuclear Information System (INIS)

Natural gas is essential to the world economy. Gas now accounts for almost a quarter of OECD primary energy requirements and is expected to become the second most important fuel in the world in the next decade. Industrial and residential consumers increasingly rely on natural gas to keep their houses warm, their lights on and their factories running. Meanwhile the gas industry itself has entered a new phase. Where gas used to be restricted to regional markets, it is now increasingly traded on a global scale. While gas production and transport requires long-term investment, now it is optimised on a short-term basis. Demand continues to grow, but local gas production has become much more expensive. How should we react? How will demand be satisfied? What changes are required to promote flexibility and trade? What are the implications for gas security, investment and interdependence? At stake is an ...

331

Laboratory development of +- 600 kVdc pipe type cable systems  

Energy Technology Data Exchange (ETDEWEB)

In 1976, the US Department of Energy and New York State - ERDA granted a contract for the development of a +-600 kV dc underground transmission cable system looking to inevitable future requirements in the US for economic, high-capacity, long-distance underground transmission linking remote generating stations to metropolitan load centers. This project was comprehensive and dealt with three separate system components, i.e., cable, splice, and terminals. In each instance, for each component, development required an intensive R and D effort, focused on the following categories: insulating materials, model testing, design of full-scale prototype, manufacturer of prototype, and laboratory development testing. Insulating papers and oils were selected, and model studies performed, for both self-contained type and pipe type oil-filled cables. However, only the pipe cable design was finally designated for full-size cable ...

1982-07-01

332

Development of flame retardant PV module encapsulants: Volume 1. Final report  

Energy Technology Data Exchange (ETDEWEB)

This Phase 1 final report covers the work performed by Springborn Testing and Research, Inc., for the period October 1, 1997 to June 30, 1998 under the Department of Energy Cooperative Agreement Number DE-FC36-97GO10255, entitled Development of Flame Retardant PV Module Encapsulants. While use of roof-mounted arrays has always been an attractive means of deploying PV, only within recent years have such building integrated concepts (BIPV) found renewed interest among module makers and end-users. Prior to building integrated and rooftop applications, flammability requirements for modules have not been a great industry concern. However, with growing interest in BIPV and the requirement for building code requirements for commercial and industrial structures, flammability issues have become a barrier to entry for many module constructions into this potentially huge domestic market for PV. The overall goal of ...

1998-06-01

333

Characterization of projected DWPF glasses heat treated to simulate canister centerline cooling  

Energy Technology Data Exchange (ETDEWEB)

Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. The glass will be produced and poured into stainless steel canisters in the Defense Waste Processing Facility (DWPF). Eventually these canistered waste forms will be sent to a geologic repository for final disposal. In order to assure acceptability by the repository, the Department of Energy has defined requirements which DWPF canistered waste forms must meet. These requirements are the Waste Acceptance Preliminary Specifications (WAPS). The WAPS require DWPF to identify the crystalline phases expected to be present in the final glass product. Knowledge of the thermal history of the borosilicate glass during filling and cooldown of the canister is necessary to determine the amount and type of crystalline phases present in the final glass product. Glass samples of seven projected ...

1992-05-01

334

CANDU 9 - the CANDU product to meet customer and regulator requirements now and in the future  

Energy Technology Data Exchange (ETDEWEB)

CANDU reactors developed under Canadian licensing regulations that placed the primary responsibility for safety on the licensee. The Atomic Energy Control Board (AECB), Canada's nuclear regulatory agency, state in their regulations what is expected in terms of safety performance so that designers are free to propose the best means of meeting this performance. This goal-oriented approach, besides encouraging innovation, allowed CANDU to be licensed in other jurisdictions. The latest design - the large, single unit, CANDU 9 - explicitly incorporates licensability in Canada through a formal AECB review of the design; lessons learned from licensing CANDU 6 in Asian countries, particularly with Wolsong 2, 3 and 4 in Korea, and more recently with Qinshan in China; utility requirements for modem evolutionary plants; and emerging international standards for safety, sponsored or issued by the IAEA. By combining the assurance of acceptability in ...

1998-07-01

335

CANDU 9 - the CANDU product to meet customer and regulator requirements now and in the future  

International Nuclear Information System (INIS)

CANDU reactors developed under Canadian licensing regulations that placed the primary responsibility for safety on the licensee. The Atomic Energy Control Board (AECB), Canada's nuclear regulatory agency, state in their regulations what is expected in terms of safety performance so that designers are free to propose the best means of meeting this performance. This goal-oriented approach, besides encouraging innovation, allowed CANDU to be licensed in other jurisdictions. The latest design - the large, single unit, CANDU 9 - explicitly incorporates licensability in Canada through a formal AECB review of the design; lessons learned from licensing CANDU 6 in Asian countries, particularly with Wolsong 2, 3 and 4 in Korea, and more recently with Qinshan in China; utility requirements for modem evolutionary plants; and emerging international standards for safety, sponsored or issued by the IAEA. By combining the assurance of acceptability in Canada ...

1998-05-03

336

Uncertainties in key low carbon power generation technologies - Implication for UK decarbonisation targets  

Energy Technology Data Exchange (ETDEWEB)

The UK government's economy-wide 60% carbon dioxide reduction target by 2050 requires a paradigm shift in the whole energy system. Numerous analytical studies have concluded that the power sector is a critical contributor to a low carbon energy system, and electricity generation has dominated the policy discussion on UK decarbonisation scenarios. However, range of technical, social and market challenges, combined with alternate market investment strategies mean that large scale deployment of key classes of low carbon electricity technologies is fraught with uncertainty. The UK MARKAL energy systems model has been used to investigate these long-term uncertainties in key electricity generation options. A range of power sector specific parametric sensitivities have been performed under a 'what-if' framework to provide a systematic exploration of least-cost ...

2009-10-15

337

Uncertainties in key low carbon power generation technologies - Implication for UK decarbonisation targets  

International Nuclear Information System (INIS)

The UK government's economy-wide 60% carbon dioxide reduction target by 2050 requires a paradigm shift in the whole energy system. Numerous analytical studies have concluded that the power sector is a critical contributor to a low carbon energy system, and electricity generation has dominated the policy discussion on UK decarbonisation scenarios. However, range of technical, social and market challenges, combined with alternate market investment strategies mean that large scale deployment of key classes of low carbon electricity technologies is fraught with uncertainty. The UK MARKAL energy systems model has been used to investigate these long-term uncertainties in key electricity generation options. A range of power sector specific parametric sensitivities have been performed under a 'what-if' framework to provide a systematic exploration of least-cost energy system configurations ...

2009-10-01

338

Thermoeconomic analysis of power plants. Final report  

Energy Technology Data Exchange (ETDEWEB)

In this report, the concept of exergy and the general methodology of the exergetic analysis and the thermoeconomic (combined exergetic and economic) analysis of energy conversion systems are presented. The THESIS (THermodynamic and Economc SImulation System) computer program used for these analyses is briefly described. Detailed mass, energy, exergy and money balances for a reference steam power plant (Harry Allen Station) are shown. The effect of the most important process parameters on the overall efficiency is investigated. A year-by-year and a levelized revenue requirement analysis are presented. The costs of exergy losses are compared with the capital costs and other expenses due to owning and operating each particular plant component. The question whether it is profitable to reduce the exergy losses by increasing these costs and vice versa is investigated. A cost sensitivity analysis including the effect of coal price ...

1984-08-01

339

The use of industrial energy in seven OECD (Organization for Economic Cooperation and Development) countries  

Energy Technology Data Exchange (ETDEWEB)

The objective of this study was to analyze the industrial demand for energy in seven Organization for Economic Cooperation and Development (OECD) countries with particular emphasis on fuel substitution between oil, natural gas, coal, and electricity. Changing fuel demand also results from economic growth, changes in industrial structure, and changes in the energy intensity of industrial output. A historical analysis of these factors and fuel substitution is undertaken for industry as an aggregate, and for 12 specific industries. The major results of the historical analysis are: (1) fuel use changes are a result of fuel switching, changing energy intensity, changing industrial structure, and economic growth; (2) fuel substitutability depends upon fuel use. The three fossil fuels are substitutes in the industrial heat market, but there are numerous special industrial processes where a particular fuel is ...

1987-01-01

340

Superconducting and optical properties of #alpha#-zirconium from its augmented-plane-wave band structure  

International Nuclear Information System (INIS)

The detailed electronic energy band structure of hexagonal close-packed #alpha#-zirconium, corresponding to the atomic configuration of 4d"25s"2 of its four outermost valence electrons, has been computed by the composite-wave variational version of the augmented-plane-wave(APW) method in conjunction with the X#alpha#(#alpha# = 0.70424) exchange approximation for obtaining the potentials. From these data the electronic density of states and its angular-momentum-decomposed components have been obtained by the Raubenheimer-Gilat method. These quantities are required in order to calculate the electron-phonon interaction parameter (lambda) and the superconducting transition temperature (Tsub(c)) within the framework of the theories of Gaspari and Gyorffy and McMillan. A study of the variation of Tsub(c) with the Coulomb pseudopotential (#mu#*) revealed that #mu#* = 0.1 yields the best agreement between theory and experiment for #alpha#-Zr. Also ...

341

Plastic wastes as support fuel. Jaetemuovin kaeyttoe tukipolttoaineena  

Energy Technology Data Exchange (ETDEWEB)

The association of Finnish Plastics Industry examined the possibilities to utilize energy content of plastic wastes in spring 1990. A bark fuelled boiler plant of forest industry was used as test power plant. The power of the plant was 60 Mw. This report discusses shortly the theory of combustion of plastics. About 130 000-15 000 tons of plastic waste, corresponding to 7 % of the solid municipal waste, is dumped annually in Finland. Utilization of the plastic waste recovered from municipal wastes for energy production is technically viable in present power plants among present energy production. The chipping and mixing of the plastic in the other fuel are the only pretreatment required for the plastic waste. In Finland there are several power plants using suitable fuels for plastic mixture combustion. The portion of the plastic of the total fuel power was 10 %. No problems occurred during the tests. The ...

1991-01-01

342

Optimisation of solar-heated cavity receivers with paraboloid collectors. Optimierung von solar beheizten Hohlraumstrahlungsempfaengern mit Paraboloidkollektoren  

Energy Technology Data Exchange (ETDEWEB)

The authors investigate the optimisation of solar-heated cavity receivers in which solar energy collected by a paraboloid collector is converted into electrical energy. The focussed solar energy enters the receiver through an aperture to heat the working fluid, which flows inside the receiver tubes and is compressed by the compressor of a gas turbine system, to the highest process temperature. A method of calculating the distribution on the inner receiver surfaces of the solar radiation reflected by the paraboloid collector is presented to begin with. The interchange of radiant energy inside the receiver cavity can be calculated on this basis, including the radiation loads, the temperatures of the inner receiver walls, and the radiative and convective losses. The temperature fields in the tube walls must be known for determining the strength required of receiver tubes; they can be ...

1984-01-01

343

Low-temperature brown rice storage by using renewable energy from snow  

Energy Technology Data Exchange (ETDEWEB)

This paper reported on a study that was conducted in Japan to determine whether renewable energy generated from snow can be used to replace the cooling system and electricity used for cooling a rice storehouse that maintained the grain temperature below 15 degrees C. However, the low-temperature storage system required a cooling system and electricity to cool rice in summer. In this study, a snow pile using 890 t of snow was made at the beginning of March next to the rice storehouse. The shape of the snow pile was a trapezium, 17 x 23 m at the bottom and 4 x 10 m at the top and 5 m in height. The snow pile was covered with 200 to 300 mm of wood chips to act as an insulation layer. Approximately 27 per cent of the energy for cooling the rice storehouse could be replaced by using the snow pile in summer. The quality of stored rice was almost similar to that of freshly harvested rice. The study showed that renewable ...

2010-07-01

344

High resolution alpha-particle spectroscopy using CR-39 plastic track detector  

Energy Technology Data Exchange (ETDEWEB)

A technique has been developed for high resolution alpha particle spectroscopy from track length determination in CR-39 plastic. On individual tracks an energy resolution deltaE close to the range straggling limit is obtainable. For 6 MeV alpha-particle deltaE is proportional 35 keV on individual particles and for groups of particles deltaE proportional 20 keV can be achieved using certain data selection criteria. At 100 keV on individual particles deltaE is proportional 20 keV. The analysis requires 1) a knowledge of the track-etch rate (Vsub(T))-range relationship and 2) a theoretical understanding of alpha-particle track structure in CR-39 as a function of particle energy, dip angle and degree of etching. The structure of alpha-particle etched tracks in CR-39 is described and two methods of analysis discussed. Examples are given of the resolution attainable on tracks of alpha-particles as natural decay ...

1984-06-15

345

Global optical model potentials for symmetrical lithium systems: "6Li+"6Li, "7Li+"7Li at E_l_a_b = 5-40 MeV  

International Nuclear Information System (INIS)

Angular distributions of "6Li+"6Li elastic scattering were measured for E_l_a_b=5-40 MeV. An optical model analysis of these data together with older data of "7Li+"7Li elastic scattering taken at E_l_a_b = 8-17 MeV was performed with the aim to search for a ''global'' OM potential which describes elastic scattering in both Li-Li systems in a broad energy range. Both surface and volume absorbing potentials can be found which fulfill this requirement if a linear energy dependence is assumed of the depths of the real as well as the imaginary potential. These depths, if fitted to individual angular distributions, are found to vary in a correlated manner with the beam energy. This is taken as indication of strong coupling between elastic, inelastic, and reaction channels. This is corroborated by the existence of resonances in reaction channels at these energies where the potential depths ...

346

German atomic energy law in the international framework. Proceedings. Deutsches Atomenergierecht im internationalen Rahmen. Tagungsbericht  

Energy Technology Data Exchange (ETDEWEB)

The regional conference was devoted to the legal problems that ensue from German reunification against the background of the integration of German atomic energy law within international law. The elements of national atomic energy legislation required by international law and recent developments in international nuclear liability law were discussed from different perspectives. The particular problems of the application of the German Atomic Energy Act in the 5 new Laender (the territories of the former GDR) were presented and discussed, namely: The continued validity of old licences issued by the GDR; practical legal problems connected with the construction of nuclear power plants in the 5 new Laender; the legal issues connected with the final repository for radioactive wastes at Morsleben; and the new developments in radiation protection law following from the Unification Treaty and the new ICRP ...

1992-01-01

347

Experience with fully operational solar-driven 10-ton LiBr/H2O single-effect absorption cooling system in Thailand  

British Library Electronic Table of Contents (United Kingdom)

A solar-driven 10-ton LiBr/H2O single-effect absorption cooling system has been designed and installed at the School of Renewable Energy Technology (SERT), Phitsanulok, Thailand. Construction took place in 2005, after which this system became fully operational and has been supplying cooling for our main testing buildings air-conditioning. Data on the systems operation were collected during 2006 and analyzed to find the extent to which solar energy replaced conventional energy sources. Here, we present these data and show that the 72m2 evacuated tube solar collector delivered a yearly average solar fraction of 81%, while the remaining 19% of thermal energy required by the chiller was supplied by a LPG-fired backup heating unit. We also show that the economics of this cooling system are domi...

2008-01-01

348

Configuration interaction studies of the HeH"+ molecular ion. IV. The triplet sigma, pi, and delta states  

International Nuclear Information System (INIS)

The method of superposition of configurations was applied to the triplet sigma, pi, and delta states of HeH"+ which correlate to the separated atom states of principal quantum number less than or equal to 3. The calculations were done for internuclear separations, 0< or =R< or =65.5 a.u., on a mesh adequate for interpolation. Similar calculations on the singlet states have already been reported. The present calculations complete the accurate evaluation of the potential energy curves for this system which are required for low- and intermediate-energy collision studies. In addition to the energy eigenvalues and eigenfunctions, dipole, gradient, and radial coupling matrix elements were calculated for the sigma and pi states. Primarily, this paper presents information on the eigenvalues. The accuracy of the triplet-state calculations is comparable to that obtained for the singlet states. The ...

8711-01-01

349

Collection of VLE data for acid gas-alkanolamine systems using Fourier transform infrared spectroscopy. Technical report, October 1, 1994--July 31, 1995  

Energy Technology Data Exchange (ETDEWEB)

The industrial standard process for the purification of natural gas is to remove acid gases, mainly hydrogen sulfide and carbon dioxide, by the absorption and reaction of these gases with alkanolamines. The natural gas industry requires vapor-liquid equilibrium (VLE) data to develop more energy efficient amine mixtures. Some energy reductions have been realized in the past decade by applying such amine systems as hindered amines, methyldiethanolamine (MDEA), and MDEA based amine mixtures. However, the lack of reliable and accurate VLE data impedes the commercial application of these more efficient alkanolamine systems. The first objective of this project is to improve the accuracy of vapor-liquid equilibrium measurements at low hydrogen sulfide concentrations. The second objective is to make VLE measurements for amine mixtures. By improving the accuracy of the VLE data on MDEA and other amines, energy ...

1995-08-01

350

Advanced nuclear data for radiation-damage calculations  

Energy Technology Data Exchange (ETDEWEB)

Accurate calculations of atomic displacement damage in materials exposed to neutrons require detailed spectra for primary recoil nuclei. Such data are not available from direct experimental measurements. Moreover, they cannot always be computed accurately starting from evaluated nuclear data libraries such as ENDF/B-V that were developed primarily for neutron transport applications, because these libraries lack detailed energy-and-angle distributions for outgoing charged particles. Fortunately, a new generation of nuclear model codes is now available that can be used to fill in the missing spectra. One example is the preequilibrium statistical-model code GNASH. For heating and damage applications, a supplementary code called RECOIL has been developed. RECOIL uses detailed reaction data from GNASH, together with angular distributions based on Kalbach-Mann systematics to compute the energy and angle distributions of recoil ...

1983-01-01

351

2001 Report on the Next Linear Collider  

Energy Technology Data Exchange (ETDEWEB)

Recent studies in elementary particle physics have made the need for an e{sup +}e{sup -} linear collider able to reach energies of 500 GeV and above with high luminosity more compelling than ever [1]. Observations and measurements completed in the last five years at the SLC (SLAC), LEP (CERN), and the Tevatron (FNAL) can be explained only by the existence of at least one particle or interaction that has not yet been directly observed in experiment. The Higgs boson of the Standard Model could be that particle. The data point strongly to a mass for the Higgs boson that is just beyond the reach of existing colliders. This brings great urgency and excitement to the potential for discovery at the upgraded Tevatron early in this decade, and almost assures that later experiments at the LHC will find new physics. But the next generation of experiments to be mounted by the world-wide particle physics community must not only find this new physics, they must find out what it ...

2001-08-28

352

The market potential for SMES in electric utility applications. Final report  

Energy Technology Data Exchange (ETDEWEB)

Superconducting magnetic energy storage (SMES) is an emerging technology with features that are potentially attractive in electric utility applications. This study evaluates the potential for SMES technology in the generation, transmission, distribution, and use of electric energy; the time frame of the assessment is through the year 2030. Comparisons are made with other technology options, including both commercially available and advanced systems such as various peaking generation technologies, transmission stability improvement technologies, and power quality enhancement devices. The methodology used for this study focused on the needs of the market place, the capabilities of S and the characteristics of the competing technologies. There is widespread interest within utilities for the development of SMES technology, but there is no general consensus regarding the most attractive size. Considerable uncertainty exists regarding the eventual ...

1994-06-01

353

Metrology measurement capabilities  

Energy Technology Data Exchange (ETDEWEB)

Since 1958, the AlliedSignal Federal Manufacturing and Technologies (FM and T) Metrology Department has developed measurement technology and calibration capability in four major areas of measurement: mechanical; environmental, gas, liquid; electrical (D.C., A.C., RF/microwave); and optical and radiation. The capabilities developed include unique capabilities in many areas of measurement and engineering expertise to develop measurement techniques and resolve measurement problems in these major areas. FM and T Metrology was established in 1958 to provide a measurement base for the Department of energy`s Kansas City Plant. The Metrology Engineering Department provides the expertise to develop measurement capabilities for virtually any type of measurement which falls into the broad areas listed above. The engineering staff currently averages almost 16 years of measurement experience. A strong audit function has been developed to provide a means to evaluate the ...

1997-06-01

354

IECEC '91; Proceedings of the 26th Intersociety Energy Conversion Engineering Conference, Boston, MA, Aug. 4-9, 1991. Vol. 2 - Aerospace power systems, conversion technologies  

International Nuclear Information System (INIS)

The present volume on energy and the environment discusses space power requirements, space power systems, space power systems hardware, space radioisotope systems, space solar arrays, space solar cells, space station power, and terrestrial applications of aerospace technology. Attention is given to NASA future space power requirements and issues, the design of a battery charger for the NASA EOS Space Platform, in situ carbon dioxide fixation on Mars, and a preliminary design update of the CRAF/Cassini Power Subsystem. Topics addressed include concentrator testing using projected images, solar power satellites and demonstraton platforms from nonterrestrial materials, a mass sensitivity analysis of lunar orbiting beam power systems, and a power-beaming-based infrastructure for space power. Also discussed are fiber-optic sensors for aerospace electrical measurements, the preliminary design of a mobile lunar power supply, ...

1991-08-03

355

Designing a healthy house - an overview  

Energy Technology Data Exchange (ETDEWEB)

There are certain factors to take into account when determining the suitability of a healthy house site. Power lines, agricultural spraying, vehicle exhaust, and industrial pollution are all potential sources of indoor air contamination. It is recommended that a environmental assessment be done to determine whether there are specific sources of contamination. Good drainage is required. The surrounding landscaping should be open and sunlit, and with low maintenance requirements. Decks and fences made from pressure-treated or chemical treated lumber should be avoided. One of the early decisions in the design process is the choice of the structural system. The key with all foundation types is to control moisture, whether from rain, from the ground, or the condensation of moisture from the air with cooling. The construction frame is sealed away from the occupants by the air/vapor barrier, so only in extreme cases is it essential to use alternatives ...

1999-11-01

356

Demonstration of innovative monitoring technologies at the Savannah River Integrated Demonstration Site  

Energy Technology Data Exchange (ETDEWEB)

The Department of Energy`s Office of Technology Development initiated an Integrated Demonstration Program at the Savannah River Site in 1989. The objective of this program is to develop, demonstrate, and evaluate innovative technologies that can improve present-day environmental restoration methods. The Integrated Demonstration Program at SRS is entitled ``Cleanup of Organics in Soils and Groundwater at Non-Arid Sites.`` New technologies in the areas of drilling, characterization, monitoring, and remediation are being demonstrated and evaluated for their technical performance and cost effectiveness in comparison with baseline technologies. Present site characterization and monitoring methods are costly, time-consuming, overly invasive, and often imprecise. Better technologies are required to accurately describe the subsurface geophysical and geochemical features of a site and the nature and extent of contamination. More efficient, nonintrusive ...

1993-12-31

357

Analysis of lagoon sludge characteristics for choice of treatment process  

Energy Technology Data Exchange (ETDEWEB)

The Korea Atomic Energy Research Institute has launched a decommissioning program of uranium conversion plant. One of the important tasks in the decommissioning program is the treatment of the sludge, which was generated during operation and stored in the two ponds of the lagoon. The treatment requires the volume reduction of lagoon sludges for the low cost of the program and the conversion of the chemical forms, including uranium, for the acceptance at the final disposal site. The physical properties, such as densities, were measured and chemical compositions and radiological properties were analyzed. The denitration was a candidate process which would satisfy the requirements for sludge treatment, and the characteristics of thermal decomposition and dissolution with water were analyzed. The main compounds of the sludge were ammonium and sodium nitrate from conversion plant and calcium nitrate, calcium carbonate from Ca ...

2002-04-01

358

The contribution of the DOE`s R&D budget in natural gas to energy price security  

Energy Technology Data Exchange (ETDEWEB)

The energy price volatility model suggests that some of the proposed natural gas programs can contribute to energy price stability. The sector most vulnerable to fuel price variations is, of course, the transportation sector. The most effective strategy to achieve energy pace stability is to reduce petroleum consumption in this sector. The natural gas vehicle program is therefore recommended as potentially important and worthy of further consideration. At this point, distinguishing the merits of various subprograms is not feasible. This result farther supports the conclusion that the DOE`s energy R&D portfolio is not efficiently balanced and an increase in oil and gas research should be a high priority. The DOE has responded favorably and has significantly increased its proposed research with the explicit objective of displacing oil in the transportation sector. The enhanced research and development ...

1992-12-01

359

Review of wood fuel from early thinning and plantation cleaning in the Netherlands  

International Nuclear Information System (INIS)

Discussions regarding the use of wood fuels for commercial energy production in the Netherlands began in the 1990's. The main reasons for using wood fuel are: the political demand for using renewable energy, the need to reduce CO_2 emissions, and the lack of markets for surplus timber. Only 10 % of the area of Holland is forested. Therefore, early thinning and cleaning are important management tools for improving growth and producing better quality timber. The energy potential from early thinning and plantation cleaning could be between 400 000 and 570 000 dry tons annually. The Netherlands has not experience in harvesting energy wood. However, through the International Energy Agency/Bioenergy Agreement, knowledge gained in other countries, especially Denmark, Sweden and Finland, is being transferred to Holland. In 1996, there have been made field tests with Danish equipment. ...

360

The cybernetics of viability: an overview  

British Library Electronic Table of Contents (United Kingdom)

A three-level approach to viability is developed, considering (1) living systems, (2) a niche, understood as the area within the reach of their actions, and (3) an environment. A systematic analysis of the interrelations between these levels shows that living systems emerge with matter/energy processing systems. These can add controller structures when producing excess energy. A three-sensor controller structure enables a living system to deal with unfavourable and scarce environments. Further evolution of these controller structures offers improved ways to act on niches. Maintaining niches in scarce environments can require technology or economy. So social systems emerge, which are understood as aggregates of living systems. Basic patterns of interactions within social systems are analyse...

2011-01-01

361

Techno-economic investigation of an air humidification-dehumidification desalination process  

Energy Technology Data Exchange (ETDEWEB)

This article presents a humidification-dehumidification (H.D.) process suitable for desalination of sea- and brackish water. The work correlated performance characteristics of the combination of different components in such a loop. Water yield, energy requirement and design data are evaluated as functions of different parameters. The investigation covered water to air mass ratios ranging from 60 to 80, concentration ratios between 2 and 5, at a temperature difference of between 10 and 16 C, along the liquid for dehumidification. The results showed that 76% of energy consumed in the humidifier is recovered by condensation. Increase of the concentration ratio to 5 can reduce the make-up water and rejected brine by about 58% and 24% respectively. Cost calculations show that the H.D. process has significant potential as an alternative for small capacity desalination plants and permits to operate systems as small as 10 m[sup ...

1993-08-01

362

Studies of accelerated compact toruses  

Energy Technology Data Exchange (ETDEWEB)

In an earlier publication we considered acceleration of plasma rings (Compact Torus). Several possible accelerator configurations were suggested and the possibility of focusing the accelerated rings was discussed. In this paper we consider one scheme, acceleration of a ring between coaxial electrodes by a B/sub theta/ field as in a coaxial rail-gun. If the electrodes are conical, a ring accelerated towards the apex of the cone undergoes self-similar compression (focusing) during acceleration. Because the allowable acceleration force, F/sub a/ = kappaU/sub m//R where (kappa < 1), increases as R/sup -2/, the accelerating distance for conical electrodes is considerably shortened over that required for coaxial electrodes. In either case, however, since the accelerating flux can expand as the ring moves, most of the accelerating field energy can be converted into kinetic energy of the ring leading to high efficiency.

1983-01-04

363

Solar-powered cooling systems: Technical and economic analysis on industrial refrigeration and air-conditioning applications  

British Library Electronic Table of Contents (United Kingdom)

In the last years, the growing demand for air conditioning has caused a significant increase in demand for primary energy resources. Solar-powered cooling is one of the technologies which allows to obtain, by using the renewable solar source, an important energy saving compared to traditional air conditioning plants. The paper describes different technical installations for solar cooling, their way of operation, advantages and limits. The objective of the present study has been to analyze the technical and economic feasibility of solar absorption cooling systems, designed for two different application fields: industrial refrigeration and air conditioning. The possibility to replace or integrate the existing plants is studied, by considering the refrigeration requirements of a company, whic...

2009-01-01

364

SOLID OXIDE FUEL CELL HYBRID SYSTEM FOR DISTRIBUTED POWER GENERATION  

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the work performed by Honeywell during the October 2001 to December 2001 reporting period under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL) entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. The main objective of this project is to develop and demonstrate the feasibility of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a turbogenerator. The conceptual and demonstration system designs were proposed and analyzed, and these systems have been modeled in Aspen Plus. Work has also started on the assembly of dynamic component models and the development of the top-level controls requirements for the system. SOFC stacks have been fabricated and performance mapping initiated.

2003-08-01

365

SI/SIGE NANOWIRE ARRAYS FOR THERMOELECTRICITY  

Environmental Research Database

ObjectivesFor thermoelectricity both low thermal conductivity and high electrical conductivity are required. High electrical conductivity should be established via a high carriers concentration and a high mobility.~%~The aim of this feasibility study is to investigate a method of modulation doping of Si nanowires in order to generate high carrier concentrations without the need for impurity doping, thus retaining high mobilities.~%~~%~The objectives are (in chronological order):~%~- reduction of the wire [continued...]DescriptionIn recent years, the increasing dependence of society on fossil fuels for socio-economical development has become a cause of great concern. The possibility of a reduced availability of fossil fuels, and the effect of these fuels on climate change, have encouraged research into alternative energy sources. Many of these alternatives are old ideas, implemented using modern techniques. This proposal plans ...

2008-01-30

366

Renewable energy technologies for irrigation water pumping in India: A preliminary attempt towards potential estimation  

Energy Technology Data Exchange (ETDEWEB)

Simple frameworks have been developed for estimating the utilization potential of: (a) solar photovoltaic (SPV) pumps; (b) windmill pumps; (c) producer gas based dual fuel engine pumps; and (d) biogas based dual fuel engine pumps for irrigation water pumping in India. The approach takes into account factors such as: solar radiation intensity, wind speed, availability of bovine dung and agri-residues, and their alternative uses, ground water requirements for irrigation and its availability, affordability, and propensity of the users to invest in renewable energy devices, etc. SPV pumps are estimated to have the maximum utilization potential in India, followed by windmill pumps. (author)

2007-05-15

367

Re-Engineering Casting Production Systems - Final Report - 03/02/1998 - 03/01/2001  

Energy Technology Data Exchange (ETDEWEB)

The goal of this three-year project was to improve the production systems in use by steel foundries in the United States. Improvements in the production systems result in less rework, less scrap, and less material handling, all of which would significantly reduce the energy demands of the process. Furthermore, these improvements would allow the companies to be more competitive, more responsive to customers' needs, deliver products with less lead time and require less capital. The ultimate result is a stronger domestic steel casting industry, which uses less energy. A major portion of this research involved the deployment of student researchers at steel foundries, to study their production systems and collect data.

2001-06-25

368

Project of the new measurement system for energy invoicing - Itaipu Hydroelectric Central; Proyecto del nuevo sistema de medicion de energia para facturacion de la Central Hidroelectrica de Itaipu  

Energy Technology Data Exchange (ETDEWEB)

Itaipu Binacional has taken a decision of executing a technological updating for the energy measurement system through the substitution of the current system by other one equipped with digital devices. The main reasons for that were the following: a) The equipment in operation were of an outdated generation b) The accuracy class of the existing equipment was of 0.5%, but the tendency for invoicing measurements was to install meters with accuracy class of 0.2% in the enterprises c) The requirements of ONS/MAE, in Brazil, which establishes the minimum requisites to be attended by invoicing measurement systems.

2001-07-01

369

Polarized electron sources  

Energy Technology Data Exchange (ETDEWEB)

Polarized electron sources for high energy accelerators took a significant step forward with the introduction of a new laser-driven photocathode source for the SLC in 1992. With an electron beam polarization of >80% and with {approximately}99% uptime during continuous operation, this source is a key factor in the success of the current SLC high-energy physics program. The SLC source performance is used to illustrate both the capabilities and the limitations of solid-state sources. The beam requirements for future colliders are similar to that of the SLC with the addition in most cases of multiple-bunch operation. A design for the next generation accelerator source that can improve the operational characteristics and at least minimize some of the inherent limitations of present sources is presented. Finally, the possibilities for producing highly polarized electron beams for high-duty-factor accelerators are discussed.

1995-05-01

370

Nuclear astrophysics with radioactive ion beams  

International Nuclear Information System (INIS)

Nuclear astrophysics seeks for a possible explanation of the observed abundance distribution of various elements and their isotopes in the universe. Most of the relevant nuclear reactions take place in thermally equilibrium environments with bare nuclei, rather than accelerated and head-on colliding situations with low ionisation states of reactant atoms and molecules that are emulated in the laboratories. Moreover, the temperature of the astrophysical environments is quite often low compared to the centre-of-mass energy of the projectile nuclides, that is required for the reaction to be meaningfully investigated in the laboratory. Therefore, an extrapolation of the data on the reaction cross sections to very low energies and to extremely high density situations is generally called for, which are substantially altered every now and then for a number of astrophysically important reactions. The radioactive ion beams will ...

371

Materials for air turbines in wave power devices. A generic study  

Energy Technology Data Exchange (ETDEWEB)

Wave energy device teams have identified three varieties of air turbine as potentially applicable to wave energy devices. These are: conventional axial turbines; Wells, or self-rectifying, axial turbines and Francis turbines. This report examines the constructional requirements of these devices with regard to mechanical, environmental and manufacturing considerations. It is concluded that the major benefit of optimum material selection will be reduced manufacturing costs rather than enhanced turbine performance. A methodology of material selection has been established and candidate materials have been listed for the major components of each turbine type. Comparative costs for alternative materials are included, from which significant, potential economies have been identified. Recommendations are made aimed at achieving optimum material usage in the proposed turbines.

1981-01-01

372

MINERGIE modules: heat pump - heat pump/solar - wood - wood/solar; Minergie-Module Waermepumpe - Waermepumpe/Solar - Holz - Holz/Solar  

Energy Technology Data Exchange (ETDEWEB)

This research report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that examined the feasibility of setting up 'MINERGIE' low-energy-consumption module standards for the production of heat in small residential buildings. The aims of the standards and the basic idea behind the MINERGIE-modules are discussed. The concepts of the modules for heat pumps and wood-fired heating systems and their combination with solar installations are examined, as are their areas of application. The requirements placed on the modules are listed. System concepts, including simple schematics for typical installations, are presented for wood-log, wood-chippings and pellets-fired systems as well as for ground-loop and air-water heat pump systems as well as their solar-aided counterparts. The results of cost-benefit analyses are presented and questions regarding system guarantee and liability are ...

2005-07-01

373

Junction conditions in General Relativity with spin sources  

CERN Document Server

The junction conditions for General Relativity in the presence of domain walls with intrinsic spin are derived in three and higher dimensions. A stress tensor and a spin current can be defined just by requiring the existence of a well defined volume element instead of an induced metric, so as to allow for generic torsion sources. In general, when the torsion is localized on the domain wall, it is necessary to relax the continuity of the tangential components of the vielbein. In fact it is found that the spin current is proportional to the jump in the vielbein and the stress-energy tensor is proportional to the jump in the spin connection. The consistency of the junction conditions implies a constraint between the direction of flow of energy and the orientation of the spin. As an application, we derive the circularly symmetric solutions for both the rotating string with tension and the spinning dust string in three ...

2006-01-01

374

Identifying fade mechanisms in high-power lithium-ion cells.  

Energy Technology Data Exchange (ETDEWEB)

Hybrid electric vehicles (HEV) need long-lived high-power batteries as energy storage devices. Batteries based on lithium-ion technology can meet the high-power goals but have been unable to meet HEV calendar-life requirements. As part of the US Department of Energy's Advanced Technology Development (ATD) Program, diagnostic studies are being conducted on 18650-type lithium-ion cells that were subjected to accelerated aging tests at temperatures ranging from 40 to 70 C. This article summarizes data obtained by gas chromatography, liquid chromatography, electron microscopy, X-ray spectroscopy and electrochemical techniques, and identifies cell components that are responsible for the observed impedance rise and power fade.

2004-01-01

375

Hot Cell Facility (HCF) Safety Analysis Report  

Energy Technology Data Exchange (ETDEWEB)

This Safety Analysis Report (SAR) is prepared in compliance with the requirements of DOE Order 5480.23, Nuclear Safety Analysis Reports, and has been written to the format and content guide of DOE-STD-3009-94 Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Safety Analysis Reports. The Hot Cell Facility is a Hazard Category 2 nonreactor nuclear facility, and is operated by Sandia National Laboratories for the Department of Energy. This SAR provides a description of the HCF and its operations, an assessment of the hazards and potential accidents which may occur in the facility. The potential consequences and likelihood of these accidents are analyzed and described. Using the process and criteria described in DOE-STD-3009-94, safety-related structures, systems and components are identified, and the important safety functions of each SSC are described. Additionally, information which describes the safety ...

2000-11-01

376

Handbook for preparation of DOE (Department of Energy) procurement request forms  

Energy Technology Data Exchange (ETDEWEB)

The Procurement and Assistance Data System (PADS) provides a mechanism for collecting, assembling, organizing, and presenting acquisition and assistance data for the Department of Energy (DOE). This handbook and associated documents establish a uniform system to report acquisition/assistance data to PADS for the collection, processing, and dissemination of official statistical data on the Department's acquisition and assistance actions. The data provides, based on information available at the time of request, a basis for any recurring and special reports to the senior procurement executive, Congress, General Accounting Office (GAO), Federal executive agencies, Office of Management and Budget (OMB), and the general public. PADS is also used to satisfy DOE's statutory reporting requirements to the Office of Management Budget, Congress, and other Federal agencies. Accurate and timely collection of PR data is a key element in this ...

1990-11-01

377

Focused ion beam (FIB) milling of electrically insulating specimens using simultaneous primary electron and ion beam irradiation  

International Nuclear Information System (INIS)

There is currently great interest in combining focused ion beam (FIB) and scanning electron microscopy technologies for advanced studies of polymeric materials and biological microstructures, as well as for sophisticated nanoscale fabrication and prototyping. Irradiation of electrically insulating materials with a positive ion beam in high vacuum can lead to the accumulation of charge, causing deflection of the ion beam. The resultant image drift has significant consequences upon the accuracy and quality of FIB milling, imaging and chemical vapour deposition. A method is described for suppressing ion beam drift using a defocused, low-energy primary electron beam, leading to the derivation of a mathematical expression to correlate the ion and electron beam energies and currents with other parameters required for electrically stabilizing these challenging materials.

2007-02-07

378

Environmental information document: Savannah River Laboratory Seepage Basins  

Energy Technology Data Exchange (ETDEWEB)

This document provides environmental information on postulated closure options for the Savannah River Laboratory Seepage Basins at the Savannah River Plant and was developed as background technical documentation for the Department of Energy`s proposed Environmental Impact Statement (EIS) on waste management activities for groundwater protection at the plant. The results of groundwater and atmospheric pathway analyses, accident analysis, and other environmental assessments discussed in this document are based upon a conservative analysis of all foreseeable scenarios as defined by the National Environmental Policy Act (CFR, 1986). The scenarios do not necessarily represent actual environmental conditions. This document is not meant to be used as a closure plan or other regulatory document to comply with required federal or state environmental regulations.

1987-03-01

379

Electronics Personal Dosemeter (EPD-N) Test and Evaluation Report  

Energy Technology Data Exchange (ETDEWEB)

Three electronic personal dosimeters (EPD-N) manufactured by Siemens, serial numbers 0635, 0658, and 0683, were tested at the Radiation Calibration Laboratory for an evaluation of their response to neutron, gamma and x-ray radiation. Designed to provide real-time neutron and photon dosimetry, the EPD-N is capable of estimating and displaying neutron and gamma dose components separately for a range of energies from 50 keV to 7 MeV for photon and 0.025 eV to > 10 MeV for neutron. All tests were conducted using the factory calibrations. A technical representative of the manufacturer indicated that site-specific calibrations are required as factory settings are calibrated for the lowest neutron energy limit of 0.025 eV. This raises concerns about the reliability of these devices in measuring neutrons when calibrations are made for a specific site radiological characterization then used at another site.

2003-04-08

380

Efficient fermentation. Future for biomass cascades; Rendabel vergisten. Toekomst voor biomassacascades  

Energy Technology Data Exchange (ETDEWEB)

In this project attention is paid to possibilities to improve the cost-effectiveness of co-fermentation and thus reduce the dependency of subsidies. A calculation model has been developed by means of which is possible to change relevant parameters and determine the exploitation cost. A sensitivity analysis shows which conditions are required to improve the cost-effectiveness of the energy and CO2, produced by fermentation. [Dutch] In dit project is gezocht naar oplossingen waarmee co-vergisting financieel aantrekkelijk wordt zonder subsidies. Daarvoor is een rekenmodel ontwikkeld waarmee het mogelijk is relevante parameters te wijzigen en vervolgens de exploitatie door te rekenen. De uitgevoerde gevoeligheidsanalyse geeft aan welke randvoorwaarden noodzakelijk zijn om het vermarkten van met behulp van vergisting geproduceerde energie en CO2 rendabel te maken.

2007-06-15

381

Data summary of municipal solid waste management alternatives  

Energy Technology Data Exchange (ETDEWEB)

The overall objective of the study in this report was to gather data on waste management technologies to allow comparison of various alternatives for managing municipal solid waste (MSW). The specific objectives of the study were to: 1. Compile detailed data for existing waste management technologies on costs, environmental releases, energy requirements and production, and coproducts such as recycled materials and compost. Identify missing information necessary to make energy, economic, and environmental comparisons of various MSW management technologies, and define needed research that could enhance the usefulness of the technology. 3. Develop a data base that can be used to identify the technology that best meets specific criteria defined by a user of the data base. Volume I contains the report text. Volume II contains supporting exhibits. Volumes III through X are appendices, each addressing a specific MSW management ...

1992-10-01

382

Construction and development of a UV free electron laser under the cooperation of Nihon U, KEK, PNC, ETL and Tohoku U  

Energy Technology Data Exchange (ETDEWEB)

The construction and the development of a UV free electron laser have been started under the cooperation of Nihon U, KEK, PNC, ETL and Tohaku U. The project requires a 100MeV S-band electron linear accelerator to expand the oscillation of FEL using fundamental mode to the UV region. The injection system consists of a thermionic RF-gun with a LaB cathode and an {alpha} magnet for magnetic bunching. We are studying to reduce the back-bombardment electrons to realize the macropulse length of 20{mu}sec. Electron beams, up to the energy of 100MeV, are injected into the optical oscillators. Changing the accelerating energy and/or undulator parameters, this system will cover the range from infrared to ultraviolet for the applications in various fields.

1995-12-31

383

COSY synchrotron and storage ring for medium energy physics  

Energy Technology Data Exchange (ETDEWEB)

At present the cooler synchrotron COSY a synchrotron and storage ring for medium energy physics is being commissioned at Juelich. The construction of the ring was finished during September 1992. The cooler ring will deliver protons in the momentum range from 270 to 3300 MeV/c. The phase density of the circulating protons will be increased with electron cooling at injection and with stochastic cooling at momenta between 1500 and 3300 MeV/c. High luminosity internal experiments as well as high resolution external experiments will be possible. Details of the lattice, to match the different ion optical requirements for cooling, acceleration, internal experiments and ultra-slow extraction will be discussed. An overview of the performance of the ion sources, the injector cyclotron, the ring, the injection beamline are given. The realization status of the extraction beamlines to the external experimental area is given. The experience on the ...

1993-01-01

384

An investigation of tidal stream rotor performance  

Environmental Research Database

ObjectivesThe practical exploitation of tidal stream energy is limited by man's activities in coastal waters: navigation, fishing and~%~leisure pursuits. It is important therefore to make the best use of the sites, which are available. The main objective of the~%~Proposed study is to assess the limits imposed by waves on the performance of tidal stream rotors, and to investigate way:~%~in which these limits might be related by refinements in rotor design and the control of operating conditions. Secondary~ [continued...]DescriptionHorizontal aids wind turbines have been recognised as one of the most successful renewable energy saving devices. The use of the similar concept as a 'tidy stream rotor' in offshore environment appears to be even more compelling. However, the application of this concept will require the confirmation of various operational and environmental limitations due to complexities of offshore environment ...

2004-01-29

385

An evaluation of the embedment of a Radio Frequency Integrated Circuit with a temperature detector in building envelopes for energy conservation  

British Library Electronic Table of Contents (United Kingdom)

Concrete is the primary material for building envelopes in some parts of the world, and its ability to store heat as well as its dynamic temperature changes will not only affect the deterioration rate of the exterior wall but will also greatly influence the energy efficiency of interior air conditioning. There are many methods for measuring the inner temperature of concrete, but they often have limitations, such as indirect estimation, cable installation requirements, high cost, or heterogeneity of the sample structure. In order to measure the internal temperature of concrete, this study integrated a Radio Frequency Integrated Circuit (RFIC) with a temperature sensor chip and embedded the device in concrete structures. A Smart Temperature Information Material (STIM) was thus developed. Thi...

2011-01-01

386

A laser reflector for multi-bunch gamma conversions in a {gamma}{gamma} collider  

Energy Technology Data Exchange (ETDEWEB)

One of the main challenges for a high energy {gamma}{gamma} collider is the high repetition rate required for the laser-electron-beam collisions to convert into high energy gamma beams. State-of-the-art, high power lasers have a much lower repetition rate than that of the electron pulses. It is therefore highly desirable that the same laser pulse can be reused. As an example, for NLC where beams collide at 120 Hz, within each collision cycle there are 90 electron bunches separated by 1.4 ns between successive bunches. We show, by invoking a recently invented laser optical box, that the laser pulses can be reused for the entire train of bunches within each collision cycle. ((orig.)).

1995-02-01

387

A laser reflector for multi-bunch gamma conversions in a #gamma##gamma# collider  

International Nuclear Information System (INIS)

One of the main challenges for a high energy #gamma##gamma# collider is the high repetition rate required for the laser-electron-beam collisions to convert into high energy gamma beams. State-of-the-art, high power lasers have a much lower repetition rate than that of the electron pulses. It is therefore highly desirable that the same laser pulse can be reused. As an example, for NLC where beams collide at 120 Hz, within each collision cycle there are 90 electron bunches separated by 1.4 ns between successive bunches. We show, by invoking a recently invented laser optical box, that the laser pulses can be reused for the entire train of bunches within each collision cycle. ((orig.)).

388

A calculation method of running range of electric vehicle with battery hybrid system  

Energy Technology Data Exchange (ETDEWEB)

Much attention is being paid to electric vehicles from environmental standpoints. One disadvantage of the electric vehicle is that its operative range is short. A means to overcome this difficulty is to use a hybrid battery which consist of a energy battery and a power battery. A method to make it possible to calculate the discharge characteristics of the battery hybrid system taking into account the charging behavior from the energy battery to the power battery is presented. In the proposed method, first the output voltage and the output current of an equivalent battery, which is required for realizing the given operating pattern are calculated. Next, the conduction ratio of the main chopper and the equivalent discharge of electric charge of each battery are calculated. These calculated data are used to calculate the operating range.

1980-05-01

389

A PAC containing the human mitochondrial DNA polymerase gamma gene (POLG) maps to chromosome 15q25  

Energy Technology Data Exchange (ETDEWEB)

The human mitochondrial DNA (mtDNA) is a closed circular, 16,569-bp double-stranded DNA, encoding 13 genes whose protein products are subunits of the oxidative phosphorylation system required for synthesis of most of the ATP consumed by eukaryotic cells. Point mutations of the mtDNA that cause multi-tissue, loss-of-energy syndromes, called mitochondrial encephalomyopathies (e.g., MERRF and MELAS), have been identified. In addition, large-scale deletions of the human mtDNA have been identified and are the molecular bases for the neonatal and adolescent onset loss-of-energy syndromes Pearson and Kearns-Sayer, respectively. 5 refs., 1 fig.

1997-03-01

390

The integration of renewable energy sources into electric power transmission systems  

Energy Technology Data Exchange (ETDEWEB)

Renewable energy technologies such as photovoltaics, solar thermal power plants, and wind turbines are nonconventional, environmentally attractive sources of energy that can be considered for electric power generation. Many of the areas with abundant renewable energy resources (very sunny or windy areas) are far removed from major load centers. Although electrical power can be transmitted over long distances of many hundreds of miles through high-voltage transmission lines, power transmission systems often operate near their limits with little excess capacity for new generation sources. This study assesses the available capacity of transmission systems in designated abundant renewable energy resource regions and identifies the requirements for high-capacity plant integration in selected cases. In general, about 50 MW of power from renewable sources can be integrated into existing ...

1995-07-01

391

Integrated solid waste management of Springfield, Massachusetts  

Energy Technology Data Exchange (ETDEWEB)

The subject document reports the results of an in-depth investigation of the fiscal year 1993 cost of the city of Springfield, Massachusetts, integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. The document reports actual data from records kept by participants. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may perform manipulation or further analysis of the data. As such, the report is a reference document for Municipal Solid Waste management professionals who are interested in the actual costs and energy consumption, for a 1-year period, of an operating IMSWM system. The report is organized into two main parts. The first part is ...

1995-11-01

392

Development requirements for absorption processes for effective CO{sub 2} capture from power plants  

Energy Technology Data Exchange (ETDEWEB)

Effective commercial liquid absorption technology currently applicable for CO{sub 2} capture from power plant flue gases uses a conventional chemical solvent, MEA(monoethanolamine), which was developed over 60 years ago as general non selective solvent to remove acid gases from natural gas streams. The application to CO{sub 2} capture from almost atmospheric pressure flue gases required modification of the technology on account of the oxygen content to incorporate inhibitors to resist solvent degradation and equipment corrosion, as well as upstream treatment of the flue gases to remove both SO{sub x} and NO{sub x} present. The solvent strength used by such processes is relatively low in comparison with high strength modern chemical solvents. The resultant effect is large equipment and high regeneration energy requirements which is a parasitic load on the power plant. Using current technology for CO{sub 2} capture from flue ...

1997-12-31

393

An FEL design for gamma-gamma colliders based on chirped pulse amplification techniques  

International Nuclear Information System (INIS)

A next generation e"+-e"- linear collider in the TeV range can be converted into a #gamma#-#gamma# collider by converting it to e"--e"- operation and then generating #gamma#-rays via Compton backscattering with optical beams. This provides unique access to some areas of fundamental physics as well as highly desirable redundancy to the collisions. The required optical beam (with a wavelength of about 1 micron) must have very high peak power, (about 1 TW) as well as average power (about 10 kW). To achieve a 1 : 1 conversion from an electron to #gamma#-quantum, each micropulse must contain about one Joule and must be about one picosecond long, the micropulse peak power being about one Terawatt. To match the electron beam pulse structure, a macropulse consists of a sequence of about one hundred micropulses separated by about one nanosecond, and the macropulses am repeated at a rate of about 100 Hz. Thus, the time average power is about 10 kW propose and analyze a ...

1995-08-21

394

Waste management systems model for energy systems sites on the Oak Ridge Reservation  

Energy Technology Data Exchange (ETDEWEB)

There is a model on the Oak Ridge Reservation which provides requirements for determining capacities and capabilities related to low-level, hazardous, and mixed wastes. In FY 1987, the model will be sufficiently advanced to provide various waste management scenarios. These scenarios will be compared technically, operationally, and financially by use of waste characterization data and process simulators that are currently under development. The results of the process simulations will be used to help identify waste treatment, storage, and disposal technologies that need to be demonstrated prior to full-scale development for DOE use. The information derived from this effort will be made available to all DOE facilities.

1986-01-01

395

UV photoemission from metal cathodes for picosecond power switches  

Energy Technology Data Exchange (ETDEWEB)

Results are reported of photoemission studies using laser pulses of 10 ps duration and 4.66 eV photon energy on metal cathodes. These included thin wires, flat surfaces and an yttrium cathode with a grainy surface. The measurements of current density and quantum efficiency under low and high surface fields indicate that field assisted efficiencies exceeding 0.1% and current densities exceeding 10/sup 5/ A/cm/sup 2/ are obtainable. The results are compared to the requirements of switch power applications. 24 refs., 13 figs., 1 tab.

1989-01-01

396

Thermodynamic Model of Aluminum Combustion in SDF Explosions  

Energy Technology Data Exchange (ETDEWEB)

Thermodynamic states encountered during combustion of Aluminum powder in Shock-Dispersed-Fuel (SDF) explosions were analyzed with the Cheetah code. Results are displayed in the Le Chatelier diagram: the locus of states of specific internal energy versus temperature. Accuracy of the results was confirmed by comparing the fuel and products curves with the heats of detonation and combustion, and species composition as measured in bomb calorimeter experiments. Results were fit with analytic functions u = f(T) suitable for specifying the thermodynamic properties required for gas-dynamic models of combustion in explosions.

2006-06-19

397

The secondary slurry-zinc/air battery  

Energy Technology Data Exchange (ETDEWEB)

The rechargeability of the slurry-Zn/air battery was demonstrated with a practical recharge cell that requires minimal hydraulic and mechanical energy for operation. A dendritic Zn was deposited on a Mg plate substrate from which it was easily, periodically and automatically scraped to regenerate dendritic Zn slurries. Excellent discharge results were obtained with the regenerated dendritic Zn slurry, comparable to those obtained with slurries made with mixtures of Zn powder. The dendritic Zn slurry allowed, however, twice the utilization of Zn. 13 refs., 24 figs., 2 tabs.

1989-07-01

398

The AECL's research reactor analysis methodology  

International Nuclear Information System (INIS)

As the cost of developing completely new computer codes becomes prohibitive, designers of nuclear facilities are turning to more cost-effective approaches for meeting increasingly strict regulatory requirements applied to safety-related analysis. For designing and licensing the MAPLE family of research reactors, Atomic Energy of Canada Ltd. (AECL) is employing the strategy of adapting major existing codes by linking them together within networks of custom-built interface software. This approach builds on the international investment in developing, maintaining, and verifying existing primary codes and focuses on the less onerous development of interface codes. The resultant code systems are then validated for the new applications of interest.

399

Spinodal decomposition and giant magnetoresistance  

International Nuclear Information System (INIS)

We explore the relation of nanostructures with the appearance of giant magnetoresistance (GMR) in melt-spun CuCo ribbons. We find by energy-filtered transmission electron microscopy that the ribbons are composed of a periodic distribution of Co within the Cu, as in spinodal decomposition. The lamellar structure should thus be associated with GMR, as only a small percentage of the Co is present in the form of grains. This is counterintuitive, for no clear interfaces are present as required by standard models, and the period of the composition oscillation (43-52 nm) is an order of magnitude larger than the mean free paths for electrons. Upon annealing, a secondary spinodal decomposition appears following the same direction as the original.

2006-10-01

400

Some physical considerations in whole skin electron beam therapy  

Energy Technology Data Exchange (ETDEWEB)

The short range of low-energy electrons has made them suitable for the treatment of skin lesions, especially when extensive areas must be irradiated with special considerations to save the normal underlying tissue. This report covers some salient features of total body electron irradiation: the construction of the large fields required, x-ray contamination levels, and multiple-field techniques. While the investigation is essentially experimental, we also indicate the results of calculations. We conclude most generally that treatment planning with whole skin irradiations can be as precise as with smaller fields.

1982-09-01

401

Site characterization progress report: Yucca Mountain, Nevada, October 1, 1990--March 31, 1991; Number 4  

Energy Technology Data Exchange (ETDEWEB)

In accordance with the requirements of Section 113 (b) (3) of the Nuclear Waste Policy Act of 1982, as amended (NWPA), the US Department of Energy (DOE) has prepared this report on the progress of site characterization activities at Yucca Mountain, Nevada, for the period October 1, 1990, through March 31, 1991. This report is the fourth in a series of reports that are issued at intervals of approximately six months during site characterization. The report covers a number of initiatives to improve the effectiveness of the site characterization program, and covers continued efforts related to preparatory activities, Study Plans, and performance assessment.

1991-10-01

402

Risk-orientated analysis of the SNR 300. Technical report 1. Risk assessment of the fast breeder reactor. Risikoorientierte Analyse zum SNR 300. Fachbericht 1. Risikobewertung des Schnellen Brueters  

Energy Technology Data Exchange (ETDEWEB)

The study required by the West German Ministry of Research and Technology (RS 605) for the Committee on 'Future Nuclear Energy Policy' of the 9th German Parliament is concerned with the following main points: 1) Assessment of technical risks from the social aspect; 2) Discussion of terms and quantification of risks; 3) 'Engineering judgment' and 'questionable' methods in the Fast Breeder analysis of the Society for Reactor Safety (GRS); 4) Assessment criteria of potential damage.

1983-09-01

403

Radiolysis of neutron irradiated lithium solutions  

International Nuclear Information System (INIS)

In the Aqueous Self-Cooled Blanket (ASCB) concept, an aqueous "6Li solution in a metallic structure is used as a shielding-breeding blanket for fusion reactors. The experimental results of this study indicate that the radiolytic gas production in an ASCB will be proportional to the absorbed radiation energy. The observed radiation chemical yields allow the preliminary estimation of the radiolysis effects for a specific ASCB design. Contrary to the theoretical predictions, the use of hydrogen as a cover gas at up to 1 MPa had no measurable effect on the radiolytic gas production. Probably it will thus not be possible to suppress the radiolytic decomposition of a low-pressure ASCB by the addition of hydrogen. Catalytic recombination will be required. (orig.).

404

Proton beam monitoring and forming on the target of isotope complex at INR linac  

International Nuclear Information System (INIS)

Special beam extraction channel is used at INR linac for isotope production. It starts from 160 MeV measuring and matching area of accelerator. This choice of beam extraction enables to direct to the target of isotope complex a proton beam of wide energy range up to 160 MeV. It is important for production of different types of nuclides. The measuring results of proton beam behavior in this region are presented. Required beam forming in 160 MeV measuring and matching area of accelerator and in beam extraction channel is discussed.

2010-01-01

405

On the development of a laser detonator  

Science.gov (United States)

The initiation of explosives by laser illumination has been known for many years. In this paper we will discuss the development of a working detonator design that reduces the energy required for detonation in a low-density secondary explosive by vaporizing a thin metal coating. We present data on the development of the design for a workhorse laser detonator that provides enhanced safety over existing exploding bridgewire detonators (EBWs). Comparison of this laser initiated data to an exploding-bridgewire (EBW) provides insight into the mechanism of initiation of detonation in low-density PETN by the plasma source. A novel diagnostic technique to determine the run-distance to detonation also known as the apparent Center-of-Initiation (COI) will also be discussed.

2005-09-01

406

Needs for Constructing and Possibilities of Nuclear Power Plants Interconnection to the Croatian Electricity Grid  

International Nuclear Information System (INIS)

Due to development of electric power system and considering an increase of electrical energy consumption, needs for larger units in new power plants are obvious. Connection of large nuclear power plants to the grid, depending on their power and location, usually requires significant investments in transmission network development and construction. Considering the capacity of the 400 kV transmission network in Croatia, this problem is evident. This paper deals with the possibilities of nuclear power plants construction, as one possible option in electric power system development, and their interconnection to the electricity grid. (author).

1998-06-15

407

Idaho National Laboratory 2013-2022 Ten-Year Site Plan  

Energy Technology Data Exchange (ETDEWEB)

The Idaho National Laboratory (INL) Ten-Year Site Plan (TYSP) describes the strategy for accomplishing the long-term objective of transforming the laboratory to meet Department of Energy (DOE) national nuclear research and development (R&D) goals, as outlined in DOE strategic plans. The plan links R&D mission goals and INL core capabilities with infrastructure requirements (single- and multi-program), establishs the 10-year end-state vision for INL complexes, and identifies and prioritizes infrastructure needs and capability gaps. The TYSP serves as the basis for documenting and justifying infrastructure investments proposed as part of the FY 2013 budget formulation process.

2011-06-01

408

Heat recovery in polyester production: a case study  

Energy Technology Data Exchange (ETDEWEB)

Energy savings in the synthetic fiber industry could be realized by using autoclave reactor condensate and boiler flue gas heat recovery. The non-cellulose (polyester) production process analysis shows that condensate returning from the reactor to the steam boiler raises inlet temperature, giving a reduced fuel requirement of about 8%. Also, boiler flue gas with a sufficiently high outlet temperature for boiler feed water and combustion air preheating results in further fuel savings. The process with an economizer saves up to 8.44%, and with a combustion air preheater, 6.25%. (Author)

1997-07-01

409

Hanford Federal Facility Agreement and Consent Order quarterly progress report for the period ending June 30, 1991  

Energy Technology Data Exchange (ETDEWEB)

This is the ninth quarterly report as required by the Hanford Federal Facility Agreement and Consent Order (Ecology et al. 1990), also known as the Tri-Party Agreement, established between the US Department of Energy (DOE), the US Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology). The Tri-Party Agreement sets the plan and schedule for achieving regulatory compliance and cleanup of waste sites at the Hanford Site. This report covers progress for the quarter that ended June 30, 1991. A total of 87 milestones have been completed to date. 39 refs., 1 fig.

1991-08-01

410

Focused ion beam technology  

Energy Technology Data Exchange (ETDEWEB)

Focussed ion beam (FIB) technology has the advantage of being a maskless process compatible with UHV processing. This makes it attractive for use in in situ processing and has been applied to the fabrication of various mesoscopic structures. The present paper reviews these results whilst putting emphasis on in situ processing by a combined FIB and molecular beam epitaxy system. The typical performance of present FIB systems is also presented. In order to utilize the potential advantages of FIB processing, reduction of damage and improvement of throughput are important, and much effort has been devoted to developing processing techniques which require a reduced dose. The importance of low-energy FIB is discussed. (author).

1993-06-01

411

Focused ion beam technology  

International Nuclear Information System (INIS)

Focussed ion beam (FIB) technology has the advantage of being a maskless process compatible with UHV processing. This makes it attractive for use in in situ processing and has been applied to the fabrication of various mesoscopic structures. The present paper reviews these results whilst putting emphasis on in situ processing by a combined FIB and molecular beam epitaxy system. The typical performance of present FIB systems is also presented. In order to utilize the potential advantages of FIB processing, reduction of damage and improvement of throughput are important, and much effort has been devoted to developing processing techniques which require a reduced dose. The importance of low-energy FIB is discussed. (author).

412

Flue gas desulfurization. Rauchgasentschwefelung  

Energy Technology Data Exchange (ETDEWEB)

Low-dust flue gases can be washed efficiently of SO/sub 2/, and the flue gas heat can be utilized. The residual heat fraction still required by the process is characterized by a temperature of 15/sup 0/K above the temperature of the purified flue gas. Marketable crystalline ammonium sulfate is produced. The high efficiency and low heat consumption are achieved by combining all process stages in a single, fully integrated cycle process free of heat and materials losses. The process is characterized by high efficiency, low investment and operating costs, recovery of thermal energy, and production of an ammonium sulfate fertilizer.

1983-04-07

413

European Space Power Conference  

International Nuclear Information System (INIS)

To support the Space Exploration Initiative (SEI), a study was performed to investigate power system alternatives for the rover vehicles and servicers that were subsequently generated for each of these rovers and servicers, candidate power sources incorporating various power generation and energy storage technologies were identified. The technologies were those believed most appropriate to the SEI missions, and included solar, electrochemical, and isotope systems. The candidates were characterized with respect to system mass, deployed area, and volume. For each of the missions a preliminary selection was made. Results of this study depict the available power sources in light of mission requirements as they are currently defined.

1991-09-02

414

Electron collisional detachment processes for a 250 keV D/sup -/ ion beam in a partially ionized hydrogen target  

Energy Technology Data Exchange (ETDEWEB)

Neutral atom beams with energies above 200 keV may be required for various purposes in magnetic fusion devices following TFTR, JET and MFTF-B. These beams can be produced much more efficiently by electron detachment from negative ion beams than by electron capture by positive ions. We have investigated the efficiency with which such neutral atoms can be produced by electron detachment in partially ionized hydrogen plasma neutralizers.

1980-09-01

415

Direct laser initiation of PETN  

Energy Technology Data Exchange (ETDEWEB)

In the early 1970s Yang and Menichelli demonstrated that direct laser illumination of low-density secondary explosive prr:ssings through a transparent window could produce detonation. 'The energy requirement for threshold initiation of detonation was reduced when a thin metal coating of metal covered the side of the window against which the low-density explosive was pressed. We have obtained experimental results that are in general agreement with the results of Renllund, Stanton and Trott (1 989) and recent: work by Nagayama, hou and Nakahara (2001). We report exploration of the effects of laser beam diameter, PEiTN density and specific surface area, and thickness of a titanium coating on the window.

2001-01-01

416

Decommissioning and dismantling. Examination of the radiation hardening of electronic components. Final report  

International Nuclear Information System (INIS)

Remote-controlled handling systems are required for work to be done in the decommissioning and dismantling of nuclear facilities. These systems are equipped with electronic devices suitable for use in working environments affected by ionizing radiation. The publication explains the step-wise progress achieved for improving the radiation resistance of electronic devices with the example of a four-quadrant controlling device for the motors of a manipulator. The radiation resistance of the device could be enhanced to radiation energies of 5.500 Gy. This means that a manipulator vehicle equipped with this controlling device can take up to approx. 15 kGy all in all, taking into account its own shielding properties. (DG).

417

Concentrated particle-hole strength observed in 0h#omega# stretched-state excitations  

International Nuclear Information System (INIS)

The wide-angle spectra of the 134-MeV (p,n) reaction on "4"8Ca, "5"4Fe, "8"8Sr, and "2"0"8Pb are each dominated by the excitation of a single state at low excitation energy. These excitations correspond to the ''0h#omega#'' stretched states and are seen to be fragmented much less than ''1h#omega#'' stretched states in medium- and heavy-mass nuclei. The normalization factors required for comparison with distorted-wave impulse-approximation calculations are >0.50 and indicate that these are the purest particle-hole states known in these nuclei.

418

Chandler Slavin | Greener Package  

Wastenet

...it only highlights the different feedstocks used in the production of fiber-based packaging materials or fossil-fuel ones; what about the energy required to convert ...feedstock, is unacceptable in trying to quantify the overall burden a specific packaging material has on the environment. As an aside, the point ... Consequentially, it is difficult to speculate on how much packaging material a company diverts from the landfill by switching from one material to another ...without specifying what geographical region said packaging material resides in. In addition, there is a lot of interest in diverting PET thermoforms from ...

419

Advances in cotton gin trash energy conversion  

Energy Technology Data Exchange (ETDEWEB)

The concept of using agricultural residues, especially cotton gin trash (CGT), as a fuel for a small cogeneration power plant based on fluidized bed gasification (FBG) requires that three problems be solved: (1) ash must be removed from the low calorific value (LCV) gas prior to combustion; (2) the high NO/sub x/ emissions associated with many biomass fuels must be significantly reduced; (3) a systems analyses of engineering/economic feasibility for potential applications must be developed. This paper addresses current research at TAMU pertaining to these problems.

1985-01-01

420

High power battery test methods for hybrid vehicle applications  

Energy Technology Data Exchange (ETDEWEB)

Commonly used EV battery tests are not very suitable for testing hybrid vehicle batteries, which may be primarily intended to supply vehicle acceleration power. The capacity of hybrid vehicle batteries will be relatively small, they will typically operate over a restricted range of states-of-charge, and they may seldom if ever be fully recharged. Further, hybrid propulsion system designs will commonly impose a higher regeneration content than is typical for electric vehicles. New test methods have been developed for use in characterizing battery performance and life for hybrid vehicle use. The procedures described in this paper were developed from the requirements of the government-industry cooperative Partnership for A New Generation of Vehicles (PNGV) program; however, they are expected to have broad application to the testing of energy storage devices for hybrid vehicles. The most important performance measure for a high power battery is its ...

1997-11-01

421

Calibration of cylindrical detectors using a simplified theoretical approach  

Energy Technology Data Exchange (ETDEWEB)

The calibration of cylindrical detectors using different types of radioactive sources is a matter of routine. The most accurate method, that of experiment, is limited by several factors when the energy interval is broad, requiring a relatively large number of primary standards, implying considerable investment of money and time. Several other techniques can be used instead, including Monte Carlo simulations and semi-empirical methods. Calculations based on the first technique require good definition of the geometry and materials, including the dead layer and window thickness together with an accurate set of cross-sections. The second technique requires two different types of experimental input, the first being from use of sources emitting cascade {gamma} rays and the second from use of sources emitting isolated {gamma} rays in order to cover the wide energy range and provide ...

2006-09-15

422

Ultrasmall superparamagnetic iron oxides (USPIOs): a future alternative magnetic resonance (MR) contrast agent for patients at risk for nephrogenic systemic fibrosis (NSF)?  

UK PubMed Central (United Kingdom)

Gadolinium (Gd) based contrast agents (GBCAs) in magnetic resonance imaging (MRI) are used in daily clinical practice and appear safe in most patients; however, nephrogenic systemic fibrosis...Full Text Available

2009-03-01

423

Review of tritium metabolism based on urine bioassay results  

Energy Technology Data Exchange (ETDEWEB)

The effective half-life based on urine bioassay results of Wolsung NPP's worker was calculated. The effective half-life for tritiated water vapour obtained was 5 {approx} 9 days. In comparison to 10 days reported for ICRP-30, it is lower than the corresponding half-life for Reference Man. Also, the half-life was calculated based on intake amount of daily water. According to this result, the metabolism was reviewed.

2001-05-01

424

Potential impacts of climate change on water availability for crops in the Okanagan Basin, British Columbia  

Energy Technology Data Exchange (ETDEWEB)

Crop water demand in the Okanagan Basin was determined for 1961 to 1990, 2010 to 2039, 2040 to 2069, and 2070 to 2099. Daily station temperature data were spatially interpolated to a 1 x 1 km grid and adjusted for elevation. Daily precipitation data were estimated across four climatic regions. Output from three global climate models (GCM), CGCM2, CSIROMk2 and HadCM3 was used to create future daily climate. Daily potential evapo-transpiration (grass reference) was estimated from an empirical relationship between Bellani-plate atmometer readings, temperature and extra-terrestrial solar radiation, and then modified by crop coefficients for all crops except pasture. Depending on GCM, projected water demand increased by 12-20% (2010 to 2039), 24-38% (2040 to 2069) and 40-61% (2070 to 2099). Possible elevated CO{sub 2} effects on stomatal conductance which may reduce water demand were not accounted for. ...

2006-11-15

425

Non-neoplastic pulmonary disease from inhaled radon daughters with uranium ore dust in beagle dogs  

International Nuclear Information System (INIS)

Daily exposures of adult beagle dogs to inhaled radon daughters plus uranium ore dust, with and without concurrent cigarette smoking, for 2 to 5-1/2 yr have produced massive pulmonary fibrosis and severe emphysema. The cumulative exposure doses are similar to those associated with a 5-fold or greater increase in death rate of uranium miners due to chronic respiratory insufficiency, including pneumoconiosis, pulmonary fibrosis, and emphysema.

1977-05-01

426

Monthly Status Report for Systems & Application Support for National Cancer Institute Center for Bioinformatics & Laboratory of Population Genetics  

Science.gov (United States)

Assisted users with expired passwords Closed 233 NCICB Support Wizard Accounts Tickets Set up Resource Accounts for individual developers to control and track access on QA Application servers Maintained daily account synchronization between GForge project developers and CVS write access accounts Created FTP and SFTP user accounts for TCGA test, analysis datasets downloads and analysis datasets management.

427

Heavy Metals in selected Edible Vegetables and their daily intake in Sanandaj, Iran  

Energy Technology Data Exchange (ETDEWEB)

The levels of four different heavy metals [cadmium (Cd), lead (Pb), chromium (Cr) and copper (Cu)] were determined in various vegetables [leek (Allium ampeloprasum), sweet basil (Ocimum basilicum), parsley (Petroselium cripsum), gardem cress (lepidium sativum) and tarragon (Artemisia dracuncullus)] cultivated around the Sanandaj city. (Author)

2009-07-01

428

Heavy Metals in selected Edible Vegetables and their daily intake in Sanandaj, Iran  

International Nuclear Information System (INIS)

The levels of four different heavy metals [cadmium (Cd), lead (Pb), chromium (Cr) and copper (Cu)] were determined in various vegetables [leek (Allium ampeloprasum), sweet basil (Ocimum basilicum), parsley (Petroselium cripsum), gardem cress (lepidium sativum) and tarragon (Artemisia dracuncullus)] cultivated around the Sanandaj city. (Author)

429

Efficacy of the Carbocyclic 2?-Deoxyguanosine Nucleoside BMS-200475 in the Woodchuck Model of Hepatitis B Virus Infection  

UK PubMed Central (United Kingdom)

Daily oral treatment with the cyclopentyl 2′-deoxyguanosine nucleoside BMS-200475 at doses ranging from 0.02 to 0.5 mg/kg of body weight for 1 to 3 months effectively reduced the level of woodchuck...Full Text Available

1998-12-01

430

Daily | Best sexual wellness info - Part 2  

Wastenet

...Box Contains One Month Supply Dietary supplement with a premium patented formula of L-Arginine, Ginseng, Ginkgo plus 13 essential vitamins, antioxidants, and minerals to support male sexual function . ArginMax for Male Sexual Fitness is a patented combination of l-Arginine, Ginseng, Ginkgo, and 13 essential vitamins and ...

431

Carcinogenesis of inhaled radio daughters with uranium ore dust in beagle dogs  

International Nuclear Information System (INIS)

Daily exposures of adult beagle dogs to inhaled radon daughters and to uranium ore dust for 4-1/2 to 6 yr have produced respiratory tract carcinomas, at similar cumulative working level months (WLM) of exposures to those which induced carcinomas in uranium miners. Biological data from the beagle-dog experiments can therefore be used for prediction of carcinogenic risk under changing exposure conditions in future uranium miners.

1977-05-01

432

Anabolic effect of human parathyroid hormone fragment on trabecular bone in involutional osteoporosis: a multicentre trial.  

UK PubMed Central (United Kingdom)

After baseline studies, 21 patients with osteoporosis were treated with human parathyroid hormone fragment (PTH 1-34) given as once-daily subcutaneous injections for 6-24 months. The dose used did not...Full Text Available

1980-06-07

433

Air quality annual report 1997; Lufthygienischer Jahresbericht 1997  

Energy Technology Data Exchange (ETDEWEB)

The Bavarian Agency for Environmental Protection (LfU) is monitoring the air quality is several bavarian regions. The daily and monthly data of concentration ration of sulfur dioxide, nitrogen oxides, carbon monoxide, ozone and other pollutants are published in yearly reports, most often as diagrams with further statistica information.

1998-12-31

434

28-Day Toxicity Study of 1-Methylethyl 2-Chloro-5-(((1-Methylethoxy)Thiomethyl)Amino)Benzoate (NSC-D629243) in Hamsters.  

Science.gov (United States)

The study was conducted to determine potential target organ toxicity and its reversibility in hamsters following twice daily oral doses of NSC-D629243 for 28 consecutive days. Male and female hamsters were administered NSC-D629243 dissolved in sesame oil ...

1992-01-01

435

Make Markets Work for Climate  

Energy Technology Data Exchange (ETDEWEB)

In developing countries with rapidly growing economies, energy consumption will more than triple by 2030. This will require more than 8 trillion euros in investments in energy in these countries. The way these investments are made will be crucial in determining whether greenhouse gas emissions will rise proportionately. By creating a worldwide, lucrative market for clean technologies, countries can use the money they set aside for fighting climate change to stimulate large-scale private investment in clean energy production and efficient energy consumption. A well-functioning market ensures that money is invested where it will be the most cost-effective and will have the greatest impact in helping to solve a generally recognised problem. This also means making sure that innovations get to the market, so as to take advantage of economies of scale. The conference on 16 and 17 October ...

2006-11-15

436

Light charged particles and intermediate mass fragments from the reactions 486, 550, 640, and 730 MeV [sup 86]Kr + [sup 63]Cu  

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the reaction [sup 86]Kr + [sup 63]Cu at incident energies of 486, 550, 640, and 730 MeV. Measurements include cross sections, angular distributions, and energy spectra for light charged particles ([sup 1,2,3]H and [sup 4]He), intermediate mass fragments (IMF) (4 [le] Z [le] 17), and heavy fragments (Z [ge] 18). Coincidences between light charged particles and between particles and fragments have been measured to obtain cross sections, energy spectra, and angular distributions. Statistical model analysis of the energy spectra for [sup 1]H and [sup 4]He detected in coincidence with the fragments has allowed estimation of [sup 1]H and [sup 4]He multiplicities associated with the evaporation residues, fragments, and composite nuclei prior to scission. A comparison of cross sections, energy spectra, angular distributions, and particle multiplicities for these ...

1992-01-01

437

Evaluation of advanced technologies for residential appliances and residential and commercial lighting  

Energy Technology Data Exchange (ETDEWEB)

Section 127 of the Energy Policy Act requires that the Department of Energy (DOE) prepare a report to Congress on the potential for the development and commercialization of appliances that substantially exceed the present federal or state efficiency standards. Candidate high-efficiency appliances must meet several criteria including: the potential exists for substantial improvement (beyond the minimum established in law) of the appliance`s energy efficiency; electric, water, or gas utilities are prepared to support and promote the commercialization of such appliances; manufacturers are unlikely to undertake development and commercialization of such appliances on their own, or development and production would be substantially accelerated by support to manufacturers. This report describes options to improve the efficiency of residential appliances, including water heaters, clothes washers and dryers, ...

1995-01-01

438

Energy analysis of a solar pre-water heating system; Analise energetica de um sistema de pre-aquecimento solar de agua  

Energy Technology Data Exchange (ETDEWEB)

Several technological alternatives have been studied taking into consideration that one of the biggest problems of the electric power companies is to provide electric power during the peak consumption periods, which largest contribution to the increase of the demand comes from the residential sector, especially by the use of electric showers. One of the most promising alternatives is the pre-water heating system for reduced power showers, developed by Universidade de Campinas and Companhia Paulista de Forca e Luz. The goal of this system is basically to reduce demand during the peak periods, in order to avoid heavy investments by the electric power companies in generation, transmission and distribution of electric power directed to low acquisitive power customers, a sector in which the electric power price is not enough to recover such investments. The objective of this paper is to evaluate the total energy required in the construction of one ...

1996-12-31

439

'Zoxy' - the zinc-air high energy battery system: with decentral charging infrastructure; ''Zoxy'' - das Zink-Luft-Hochenergiebatterie-System mit dezentraler Lade-Infrastruktur  

Energy Technology Data Exchange (ETDEWEB)

Storing electrical energy in batteries is not a viable option for sustaining a country's energy economy. The mass and volume, as well as the costs, of electrochemical components required for this would be beyond all reason. Nevertheless, in certain applications the storage of electrical energy does have significant advantages over other technologies. For example, electrically powered road vehicles emit no exhaust fumes and very little noise at their place of operation. In this way they contribute substantially to air and noise pollution control in urban areas. Photovoltaic applications permit environmentally friendly electricity applications in places remote from the public grid where conventional solutions are prohibitively expensive. More than in the past, battery systems today have to meet a wide range of technical, economic and ecological requirements in order to be ...

1997-02-01

440

Optical second-harmonic generation in III-V semiconductors: Detailed formulation and computational results  

Science.gov (United States)

In an earlier paper (Phys. Rev. Lett. 66, 41 (1991)), we calculated both the dielectric constant ({epsilon}{sub {infinity}}) and the nonlinear optical susceptibilities for second-harmonic generation ({chi}{sup (2)}) in the static limit for AlP, AlAs, GaP, and GaAs in the local-density approximation with and without a self-energy correction in the form of a scissors operator,'' including local-field effects. In this paper, we expand our presentation of this calculation. Agreement with experiment to within 15% for the nonlinear susceptibility is demonstrated where experiments are available (GaP and GaAs); the dielectric constants are in no worse than 4% agreement with experiment. The virtual hole'' contributions are reformulated to avoid large numerical cancellations in the case of near degeneracies. The virtual electron'' terms dominate over the virtual hole'' terms by about one order of ...

1991-12-15

441

Combustion of refuse-derived fuels in grate and fluidised bed furnaces; Ersatzbrennstoffverbrennung in Rost- und Wirbelschichtoefen  

Energy Technology Data Exchange (ETDEWEB)

In addition to the goal of ensuring waste disposal, thermal waste treatment has always been aimed at the energy-efficient utilisation of wastes. Developments in waste management have led to an increase in high-calorific waste arisings. This is attributable to the use of mechanical-biological waste treatment as well as to segregated waste collection systems. High-calorific wastes are equivalent to fossil fuels in terms of their calorific content. Furthermore, they fulfil the legal requirements for conversion to energy. Another source of high-calorific wastes suitable for conversion to energy can be made available through the segregated disposal of industrial wastes, in many cases at low cost. These high-calorific fractions of varying origin and composition are referred to generically as substitute fuels, a term which implies quality and availability by reference to other fuels. Specifically, the term ...

2005-07-01

442

Nuclear new-build - Status and Outlook from a German utility perspective  

International Nuclear Information System (INIS)

Full text: As one of the Top 5 utilities in Europe, Rheinisch-Westfaelisches Elektrizitaetswerk AG, FWB: RW, RWE, operates a diversified generating capacity of about 45 GW; RWE Power alone generates over 30 GW. Besides a share of approximately 20% nuclear power, a large proportion of the generating base is in lignite and hard coal. RWE has an ambitious, Euro10 bn newbuild program of about 10 GW modern fossil fired plants and further expansion plans across Europe. By 2012, RWE intends to invest between Euro 15 and 20 bn outside Germany.The European Union has a challenging policy to increase the share of renewables, improve energy efficiency, and reduce greenhouse gases by 2020. At the same time, ageing power plants need to be replaced. This requires an enormous investment program across Europe. Nuclear power therefore, as a proven technology with low lifecycle carbon emissions and reasonable lifecycle cost, is a crucial contributor to achieve ...

2009-10-12

443

Unconventional systems for lunar base power generation and storage  

International Nuclear Information System (INIS)

Recent advances in thin film solar photovoltaic converters (PV's) can furnish multimegawatt power levels during lunar daylight periods with only modest mass requirements. The extended duration of lunar night (ca. 354 hr) and the high specific mass of earth-imported energy storage systems (regenerative fuel cells, batteries, etc.) render PV plus import storage power systems non-competitive with nuclear power plants for lunar bases. However, power storage or generation methods which can be constructed using primarily lunar materials, used either alone or with lightweight PV's, can be attractive alternatives to nuclear power. Three separate generic systems which can provide favorable low import mass goals have been identified and studied. These are: gravitational energy generation using lunar soil, thermal energy storage using basalt rock or glass, and electrochemical storage using lunar derived electrodes ...

1990-08-12

444

The 1992 Pacific Northwest Residential Energy Survey : Phase 1 (PNWRES92-I) : Book 12 : Non-Respondent Survey.  

Energy Technology Data Exchange (ETDEWEB)

This book constitutes a portion of the primary documentation for the 1992 Pacific Northwest Residential Energy Survey, Phase I. The complete 33-volume set of primary documentation provides information needed by energy analysts and interpreters with respect to planning, execution, data collection, and data management of the PNWRES92-I process. Thirty of these volumes are devoted to different ``views`` of the data themselves, with each view having a special purpose or interest as its focus. Analyses and interpretations of these data will be the subjects of forthcoming publications. Conducted during the late summer and fall months of 1992, PNWRES92-I had the over-arching goal of satisfying basic requirements for a variety of information about the stock of residential units in Bonneville`s service region. Surveys with a similar goal were conducted in 1979 and 1983. This volume contains a follow-up study of non-respondents to ...

1993-08-01

445

Programmed improvements of the alternating gradient synchrotron complex at Brookhaven National Laboratory, Upton, New York. Environmental assessment  

Energy Technology Data Exchange (ETDEWEB)

The purpose and need for DOE to undertake the actions described in this document are to improve the efficiency of the Alternating Gradient Synchrotron (AGS) complex. Benefits would include optimization of the AGS scientific program, increased high-energy and nuclear physics experimentation, improved health and safety conditions for workers and users, reduced impact on the environment and the general public, energy conservation, decreased generation of hazardous and radioactive wastes, and completion of actions required to permit the AGS to be the injector to the Relativistic Heavy Ion Collider (RHIC)., Improved efficiency is defined as increasing the AGS`s capabilities to capture and accelerate the proton intensity transferred to the AGS from the AGS booster. Improved capture of beam intensity would reduce the beam losses which equate to lost scientific opportunity for study and increased potential for radiation doses to ...

1994-03-01

446

Performance of the AMS-02 Experiment for High Energy Gamma Ray Astrophysics  

CERN Document Server

AMS is a particle detector designed to perform high precision measurements of the cosmic rays fluxes with the main goals of searching for anti-nuclei, as remnants of primordial anti-matter, and of measuring the faintest components of the cosmic flux, anti- protons, positrons and high energy photons. To fulfill the requirements of large acceptance, long exposure time and excellent particle identification needed to achieve the intended results, AMS will operate in space as an attached payload to the International Space Station (ISS), being the first full featured particle physics experiment to operate in the Earth orbit. The AMS-02 accurate measurements of cosmic-ray nuclei, protons, antiprotons, electrons and positrons will be completed by high energy gamma rays detection. The experiment will detect gamma-rays, either by reconstructing e+e? pairs generated by photons converted upstream the tracker (conversion mode), or based ...

2007-01-01

447

Methods of selection in heavy ion collisions at Fermi energies and de-excitation modes with the INDRA multi-detector; Methodes de tri dans les collisions d'ions lourds aux energies de Fermi et modes de desexcitation avec le multidetecteur INDRA  

Energy Technology Data Exchange (ETDEWEB)

The progress made in particle detection, particularly the design of multi-detectors, like INDRA, that cover a solid angle of almost 4{pi}, have given a new impetus to heavy ion collisions. These detectors are demanding for an efficient way of selecting events that have a common history or similar features, for instance the events representing the de-excitation of a unique emitter. The problem is to find the adequate variable on which the discrimination can be based. Different methods are proposed in this work, the common point is that they require efficient models to reproduce and analyse experimental data in order to apprehend the equation of state of nuclear matter. Most of these models are based on the numerically solving of the nuclear Boltzmann equation. The application to the Ni + Ni reaction with an energy ranging from a few A.MeV to more than 50 A.MeV illustrates this work. (A.C.)

2005-11-15

448

Load calculation and system evaluation for electric vehicle climate control  

Energy Technology Data Exchange (ETDEWEB)

This paper presents an analysis of the applicability of alternative systems for electric vehicle (EV) heating and air conditioning (HVAC). The paper consists of two parts. The first part is a cooling and heating load calculation for electric vehicles. The second part is an evaluation of several systems that can provide the desired cooling and heating in EVs. These systems are ranked according to their overall weight The overall weight is calculated by adding the system weight and the weight of the battery necessary to provide energy for system operation. The system with the minimum overall weight is considered to be the best, because minimum vehicle weight decreases the energy required for propulsion, and therefore increases the vehicle range. Three systems are considered as the best choices for EV HVAC. These are, vapor compression, ice storage and adsorption systems. These systems are evaluated, including calculations of ...

1994-09-12

449

Interacting tachyons in classical and quantum physics  

International Nuclear Information System (INIS)

It is demonstrated that tachyons do not violate the principles of relativity, and that, with the aid of a reinterpretation principle to eliminate negative energies, tachyons can be characterized as particles of real, spacelike 4-momentum. The classical, charged tachyon is treated within conventional electromagnetic theory, and in an explicitly Lorentz-invariant way. It is shown that a charged tachyon would not emit electromagnetic radiation in a vacuum regardless of its state of motion. A theory based on the real-energy solutions of the Klein-Gordon equation with imaginary mass is shown to provide the best opportunity for describing spinless tachyons in quantum field theory. The theory should be Lorentz-invariant, incorporate the reinterpretation principle to remove negative energies, and be as close as possible to conventional quantum theory. The proposal of Arons and Sudarshan is adopted as best fulfilling these ...

450

Geothermal Heat Pump research and development studies at Sandia National Laboratories  

Energy Technology Data Exchange (ETDEWEB)

The Geothermal Heat Pump (GHP) concept was originally developed in the 1940`s. Recently, because of increasing energy costs, utility interest, and the development of simple and durable ground source heat exchangers, GHP`s have gained international attention as a proven means of energy conservation and electrical peak power demand reduction. GHP systems require installation of a buried heat exchanger to utilize the nearly constant ground temperature making them more efficient than conventional air source heat pumps. However, the high installation cost for both residential and commercial applications is a major obstacle to their market penetration. Sandia National Laboratories (SNL) through its sponsors, the Department of Energy (DOE), and the Department of Defense (DOD), has embarked on a research program to find ways to reduce GHP installation costs and improve performance, thereby increasing their ...

1994-08-01

451

Fusion power and the environment  

Science.gov (United States)

Environmental characteristics of conceptual fusion-reactor systems based on magnetic confinement are examined quantitatively, and some comparisons with fission systems are made. Fusion, like all other energy sources, will not be completely free of environmental liabilities, but the most obvious of these-- tritium leakage and activation of structural materials by neutron bombardment-- are susceptible to significant reduction by ingenuity in choice of materials and design. Large fusion reactors can probably be designed so that worst-case releases of radioactivity owing to accident or sabotage would produce no prompt fatalities in the public. A world energy economy relying heavily on fusion could make heavy demands on scarce nonfuel materials, a topic deserving further attention. Fusion's potential environmental advantages are not entirely ''automatic'', converting them into ...

1975-06-01

452

Free electron laser  

International Nuclear Information System (INIS)

The present article outlines major features of the free electron laser (FEL) and reviews research and development of FEL. Relations among the oscillation frequency, electron beam parameters and wiggler parameters, the physical mechanism of amplification and the physical process of saturation are discussed to identify the difference between FEL and other lasers. The report also outlines techniques for accelerators which are used to generate high-quality, high-energy electron beams required for FEL experiments. Techniques to achieve a short wavelength, high output and high efficiency, and applications of FEL are also discussed. FEL consists of an electron accelerator, wiggler and optical resonator. In FEL, electron beams with a relativistic energy interact resonantly with an electromagnetic field to generate coherent electromagnetic waves. Unlike conventional lasers, FEL does not surfer from restrictions on its oscillation ...

453

Exploratory Technology Research Program for Electrochemical Energy Storage. Executive Summary report, 1992  

Energy Technology Data Exchange (ETDEWEB)

This summary denotes the progress made by the Exploratory Technology Research (ETR) Program for Electrochemical Energy Storage during calendar year 1992. The primary objective of the ETR Program, which is sponsored by the US Department of Energy (DOE) and managed by Lawrence Berkeley Laboratory (LBL), is to identify electrochemical technologies that can satisfy stringent performance, durability and economic requirements for electric vehicles (EVs). The ultimate goal is to transfer the most-promising electrochemical technologies to the private sector or to another DOE program (e.g., SNL`s Electric Vehicle Advanced Battery Systems Development Program, EVABS) for further development and scale-up. Besides LBL, which has overall responsibility for the ETR Program, LANL and BNL have participated in the ETR Program by providing key research support in several of the program elements. Program consists of three major elements: ...

1993-10-01

454

Experimental electrochemical capacitor test results  

Energy Technology Data Exchange (ETDEWEB)

Various electrochemical capacitors (ultracapacitors) are being developed for hybrid vehicles as candidate power assist devices for the fast response engine. The primary functions of the ultracapacitor are to level the dynamic power loads on the primary propulsion device and recover available energy from regenerative breaking during off-peak power periods. Ultracapacitors show promise toward being able to accept high regenerative pulses while exhibiting very high cycle life. This paper will present test data from selected US Department of Energy (DOE) supported ultracapacitor projects designed to meet the fast response engine requirements. Devices containing carbon, conducting polymers, and metal oxide electrode materials in combination with aqueous or organic electrolytes are being supported by the DOE. This paper will present and discuss testing data obtained from recent prototype capacitors supplied by Maxwell ...

1997-11-01

455

Experimental Evaluation And Simulation Of Multi-pixel Cadmium-zinc-telluride Hard-x-ray Detectors  

CERN Document Server

This dissertation describes the evaluation of many-pixel Cadmium-Zinc-Telluride (CdZnTe) hard-X-ray detectors for future use with the High Energy Replicated Optics (HERO) telescope being developed at Marshall Space Flight Center. The detector requirements for the HERO application are good energy resolution (sufficient to resolve cyclotron features and nuclear lines), spatial resolution of ∼200 μm, minimal charge loss of absorbed X rays, and minimal sensitivity to the background environment. This research concentrates on assessing the suitability of these detectors for the focus of HERO, and includes the development of a simulation of the physics involved in an X-ray-detector interaction, a study of the intrinsic material properties, measurements with prototype detectors such as the energy and spatial resolution, charge loss, and X-ray background reduction through 3-dimensional depth ...

2004-01-01

456

Energy recovery for Kent and Sussex Counties, Delaware: Phase II study report  

Energy Technology Data Exchange (ETDEWEB)

The work reported is to evaluate two alternative resource recovery systems which would produce a fuel or an energy product (steam) for sale to an industrial plant. The first alternative is a refuse derived fuel (RDF) production facility which would process waste to produce fuel for sale to the plant. The RDF would be co-fired with coal in new boilers. The second alternative is a mass burn steam generation facility which would produce high pressure superheated steam for sale. The steam would be used by the plant to cogenerate electricity and for the process. Conceptual designs are developed for each alternative to form the basis of estimates of capital and operating costs and potential energy revenues. Operating requirements are developed for both alternatives. An assessment is made of the impact of both alternatives on the environment, and it is concluded that the impact of either alternative will be negligible. Order of ...

1982-12-01

457

Elise plans and progress  

International Nuclear Information System (INIS)

Elise is a heavy ion induction linear accelerator that will demonstrate beam manipulations required in a driver for inertial fusion energy. With a line charge density similar to that of heavy ion drivers, Elise will accelerate a #>=# 1 gs beam pulse of K"+ ions from an initial energy of 2 MeV to a final energy #>=# 5 MeV. In the present design, the Elise electrostatic quadrupoles (ESQ) will have a 2.33 cm radius aperture operating at #+-#59 kV. The half-lattice periods range from 21 cm to 31 cm. The entire machine will be approximately 30 m long, half of that is the induction accelerator and the remaining half is the injector (including the Marx generator) and the matching section. Elise will be built in a way that allows future expansion into the full ILSE configuration, therefore it will have an array of four ESQ focusing channels capable of transporting up to a total of 3.2 A of beam current. ...

1995-09-06

458

Economic analysis for utilization of geothermal energy by North Dakota Concrete Products Co.  

Energy Technology Data Exchange (ETDEWEB)

North Dakota Concrete Products Company uses a steam curing process that accelerates the concrete curing so that 28-day strength is obtained within 24 hours. The cost of energy required to accomplish this is significant, amounting to approximately $80,000 in 1980. The present boilers are oil fired. Recently, fuel oil prices have increased substantially. Further, supply shortages in the past have threatened plant production. The purpose of this study was to evaluate the economic feasibility of using deep formation warm water as an alternative energy source. A water-to-water heat pump system to replace the existing boiler system was investigated. TPI, Inc. economic and engineering findings for this particular potential geothermal application are disclosed. The operating cost savings of the geothermal system over the operating costs of the existing oilfired system would be insufficient to provide an acceptable rate of return on ...

1982-02-01

459

Development of high power negative ion sources for fusion at JAERI  

Energy Technology Data Exchange (ETDEWEB)

Technologies producing high power negative ion beams have been highly developed in these years at JAERI for use in neutral beam injectors for heating the thermonuclear fusion plasmas. At present, it is possible to produce multi-ampere H-/D- ion beams quasi-continuously at energies more than a few hundred keV with a good beam optics of beamlet divergence of a few milli-radian. Based on these technologies, two R and D projects have been initiated; one is to develop a 22A/500keV/10s D- ion source for the neutral beam injector for JT-60U, and the other is to develop a 1A/1MeV/60s H- ion source to demonstrate high current negative ion acceleration up to the energy of 1MeV, the energy required for the neutral beam injector for International Thermonuclear Experimental Reactor (ITER). (author).

1995-10-01

460

Determination of pressure distribution in an aerated bed in a controlled pilot-scale compost reactor  

Energy Technology Data Exchange (ETDEWEB)

This study investigated the effectiveness of dealing with biological waste by composting. In particular, it examined the feasibility of recovering excess thermal energy produced in the process of composting biological waste in terms of mass and energy transport parameters required in the aerated compost bed. An experiment was performed in which a 100 dm{sup 3} adiabatic, leak-tight reactor equipped with a controlled aeration system was constructed to study the temperature and pressure distribution in the bed. Sensors were used to determine the amount and humidity of emitted gases under variable external physical conditions. The perforated bottom of the reactor allowed for bed aeration. As such, the humidity and heat were transported upwards, forced by the air pumped in and by natural convection. In terms of pressure distribution inside the composted and aerated bed, the study results showed that there were considerable ...

2010-07-01

461

Design of electron beam accelerators for microwave application  

Energy Technology Data Exchange (ETDEWEB)

Relativistic electron beams are used for generating high power microwaves. These microwave sources require electron beam generators spanning significant ranges in voltage and impedance. The pulsed power technology used to generate these electron beams is presented. Electron beam generators that produce beams with pulse durations in the 10-ns to 100-ns regime consist of an energy-storage section, pulse-shaping section, and an electron beam diode. The energy-storage section is either a Marx generator or capacitor bank-pulsed transformer. The pulse shaping is done with high-voltage transmission lines. The electron beam diode is usually a cold-cathode, space-charge-limited flow device. For longer pulses (/approximately/1 ..mu..s) the energy storage and pulse chaping can be combined. Lumped-element pulse-forming networks (PFN) can be designed to produce the desired pulse shape. The Marx generator becomes one ...

1988-07-01

462

Design of electron beam accelerator for microwave application  

Energy Technology Data Exchange (ETDEWEB)

Relativistic electron beams are used for generating high power microwaves. These microwave sources require electron beam generators spanning significant ranges in voltage and impedance. The pulsed power technology used to generate these electron beams is presented. Electron beam generators that produce beams with pulse durations in the 10 ns to 100 ns regime consist of an energy storage section, pulse shaping section, and an electron beam diode. The energy storage section is either a Marx generator or capacitor bank-pulsed transformer. The pulse shaping is done with high-voltage transmission lines. The electron beam diode is usually a cold-cathode, space-charge-limited flow device. For longer pulses (approx.1 ..mu..s) the energy storage and pulse shaping can be combined. Lumped-element pulsed-forming networks (PFN) can be designed to produce the desired pulse shape. The Marx generator becomes one of the ...

1988-01-01

463

Design for environment for the National Ignition Facility  

Energy Technology Data Exchange (ETDEWEB)

The National Ignition Facility (NIF) will be a U.S. Department of Energy (DOE) national center for inertial confinement fusion (ICF) and other research into the physics of high temperatures and high densities, and a vital element of the DOE`s nuclear weapons Stockpile Stewardship and Management Program. It will be used by scientists from a numerous different institutions and disciplines to support research advancements in national security, energy, basic science, and economic development. Multiple powerful laser beams will `ignite` small fusion targets, helping liberate more energy than is required to initiate the fusion reactions. This paper discusses the Design for Environment process for NIF, some of the subsequent activities resulting from the initial study, and a few of the lessons learned from this process. Subsequent activities include the development of a Pollution Prevention and Waste ...

1998-05-01

464

Conceptual design of a sodium sulfur cell for US electric-van batteries  

Energy Technology Data Exchange (ETDEWEB)

A conceptual design of an advanced sodium/sulfur cell for US electric-van applications has been completed. The important design factors included specific physical and electrical requirements, service life, manufacturability, thermal management, and safety. The capacity of this cell is approximately the same as that for the ``PB`` cell being developed by Silent Power Limited (10 Ah). The new cell offers a 50% improvement in energy capacity and nearly a 100% improvement in peak power over the existing PB cells. A battery constructed with such cells would significantly exceed the USABC`s mid-term performance specifications. In addition, a similar cell and battery design effort was completed for an advanced passenger car application. A battery using the van cell would have nearly 3 times the energy compared to lead-acid batteries, yet weigh 40% less; a present-day battery using a cell specifically designed for this car would ...

1993-05-01

465

Comparison of maintenance energy expenditures and growth yields among several rumen bacteria grown on continuous culture.  

Science.gov (United States)

Maintenance energy expenditures were mesured for five rumen bacteria, Selenomonas ruminantium, Butyrivibrio fibrisolvens, Bacteroides ruminicola, Megasphaera elsdenii, and Streptococcus bovis, by using a complex medium with glucose as the carbon source. Large differences (as high as 8.5-fold) in maintenance energy expenditures were seen among these bacteria. The suggestion is made that maintenance requirements could be a significant determinant of bacterial competition in the rumen. Theoretical maximum growth yields, calculated from double reciprocal plots of yield versus dilution rate, were compared to theoretical Y(ATP) values in order to estimate minimum molar adenosine 5'-triphosphate yields from glucose for each bacterium. Results showed that relative yield among the bacteria was growth rate dependent. At high dilution rates, both S. ruminantium and S. bovis produced lactate as their principal fermentation product. At ...

1979-03-01

466

Comparison of advanced engines for parabolic dish solar thermal power plants  

Science.gov (United States)

A paraboloidal dish solar thermal power plant produces electrical energy by a two-step conversion process. The collector subsystem is composed of a two-axis tracking paraboloidal concentrator and a cavity receiver. The concentrator focuses intercepted sunlight (direct, normal insolation) into a cavity receiver whose aperture encircles the focal point of the concentrator. At the internal wall of the receiver the electromagnetic radiation is converted to thermal energy. A heat engine/generator assembly, which is mounted directly behind th receiver, then converts the thermal energy captured by the receiver to electricity. Developmental activity has been concentrated on relatively small power modules which employ 11- to 12-m-diam dishes to generate nominal power levels of approximately 20 kW. A comparison of advanced heat engines for use on the dish power module is presented in terms of the performance potential of each engine ...

1982-09-01

467

Challenges in fabrication of 180deg magnet chamber  

International Nuclear Information System (INIS)

180 deg magnet chamber is used in Folded Tandem Ion Accelerator for passage and 180 deg bending of ion beam. The chamber is placed between 180 deg terminal magnet (Electro-magnet), which is used for bending, and analysing the beams. Magnet with a particular magnetic field strength bends ions of only specified mass energy product through a precise path. There is also a space limitation in the direction of magnetic field. Both of them require the magnet chamber to be of a close tolerance. Accuracy of center distance between inlet and outlet port of the magnet chamber has to be at par with the concentricity of high energy and low energy beam line. To achieve this we started the fabrication of magnet chamber by following two methods: a) Circular rolling and bending of rectangular tube for 180 deg sector of magnet chamber b) Machining 180 deg sector in two half and welding. By first method we could not ...

2006-11-01

468

Application of realistic meson-exchange forces in the broken-pair model  

Energy Technology Data Exchange (ETDEWEB)

A G-matrix, derived from a meson-exchange potential in nuclear matter, is applied to finite, semi-magic nuclei. For the open shell the broken-pair model, which can accommodate many single-particle levels, is used. The excitations of the closed shell are treated as particle-hole states. Energy spectra and electromagnetic transition densities are calculated for /sup 88/Sr and /sup 58/Ni. The energies of the non-collective states are well described. Pairing correlations in the ground state have almost the correct strength in a multishell model space. To improve the energies of the collective 2/sup +/ and 3/sup -/ states the inclusion of core-polarisation effects in the force is required. Transition charge densities for collective states become strongly surface-peaked by core-polarisation effects, as is observed in experiments. The effects of pairing correlations and core polarisation on the magnetic form ...

1985-03-11

469

Application of realistic meson-exchange forces in the broken-pair model  

International Nuclear Information System (INIS)

A G-matrix, derived from a meson-exchange potential in nuclear matter, is applied to finite, semi-magic nuclei. For the open shell the broken-pair model, which can accommodate many single-particle levels, is used. The excitations of the closed shell are treated as particle-hole states. Energy spectra and electromagnetic transition densities are calculated for "8"8Sr and "5"8Ni. The energies of the non-collective states are well described. Pairing correlations in the ground state have almost the correct strength in a multishell model space. To improve the energies of the collective 2"+ and 3"- states the inclusion of core-polarisation effects in the force is required. Transition charge densities for collective states become strongly surface-peaked by core-polarisation effects, as is observed in experiments. The effects of pairing correlations and core polarisation on the magnetic form factor of the 3.486 ...

470

Advanced fuzzy logic controllers design and evaluation for buildings' occupants thermal-visual comfort and indoor air quality satisfaction  

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to present and evaluate control strategies for adjustment and preservation of air quality, thermal and visual comfort for buildings' occupants while, simultaneously, energy consumption reduction is achieved. Fuzzy PID, fuzzy PD and adaptive fuzzy PD control methods are applied. The inputs to any controller are: the PMV index affecting thermal comfort, the CO{sub 2} concentration affecting indoor air quality and the illuminance level affecting visual comfort. The adaptive fuzzy PD controller adapts the inputs and outputs scaling factors and is based on a second order reference model. More specifically, the scaling factors are modified according to a sigmoid type function, in such a way that the measured variable to be as closer as possible to the reference model. The adaptive fuzzy PD controller is compared to a non-adaptive fuzzy PD and to an ON-OFF one. The comparison criteria are the energy ...

2001-07-01

471

A partitioned central solar receiver  

International Nuclear Information System (INIS)

Else of solar energy as substitute for conventional fuels at a competitive cost requires efficient conversion from solar radiation to usable forms of energy. In solar thermal or thermochemical applications, high efficiency usually re- quires high temperature and high concentration of incoming radiation. The main form of energy loss from high temperature solar central receivers is thermal emission ('re radiation'), at an effective temperature close to the maximum receiver temperature. This loss is reduced if the aperture is divided into segments, most of which are maintained at lower temperatures. A two-stage partitioned receiver demonstrating this concept is under construction at the Weizman Solar Tower. The high-temperature stage is the DIAPR (Directly Irradiated Annular Pressurized Receiver). The low-temperature stage is made of tubular cavity receivers of simpler design. Preliminary optical and ...

1996-05-01

472

Materials used in new generation vehicles: supplies, shifts, and supporting infrastructure  

Energy Technology Data Exchange (ETDEWEB)

The Partnership for a New Generation of Vehicles (PNGV) program intends to develop new designs for automobiles that will reduce fuel consumption by two thirds but otherwise have price, comfort, safety, and other measures of performance similar to the typical automobile now on the market. PNGV vehicle designs are expected to substitute lightweight materials, such as aluminum, magnesium, carbon-reinforced polymer composites, glass-reinforced polymer composites, and ultra- light steel, for heavier materials such as steel and iron in automobile components. The target mass of a PNGV vehicle is 1,960 pounds, as compared to the average current vehicle that weights 3,240 pounds. Other changes could include the use of different ferrous alloys, engineering changes, or incorporation of advanced ceramic components. Widespread adoption of these vehicle designs would affect materials markets and require concurrent development and adoption of supporting technologies to supply the ...

1997-08-01

473

Criticality experiments: analysis, evaluation, and programs. 6. CORAL-I Reactor: Evaluation of Critical Experiments and Mass Reactivity Coefficient Measurement  

International Nuclear Information System (INIS)

CORAL-I was an experimental, zero-power, fast-spectrum, high-enriched metal uranium reactor that operated from 1968 until 1988 at the former Junta de Energia Nuclear (JEN), CIEMAT at present. The critical measurements performed at the startup of the reactor are being evaluated as part of the International Critical Safety Benchmark Evaluation Program (ICSBEP) and proposed to be included in its 2001 edition. Additionally, the measurement of the mass reactivity coefficient is compared with MCNP4B calculations. This measurement allows one to perform the approach to critical without the need of a previous control rod calibration, thus enhancing the safety of such an approach. This technique can also be applied to other reactor types. CORAL-I (Ref. 1) is a 90% enriched metal uranium reactor domestically designed and manufactured in the experimental facilities of JEN, now CIEMAT, in Madrid, Spain. The enriched uranium was supplied by the International Atomic Energy Agency ...

2001-06-17

474

Use of a convolution/superposition-based treatment planning system for dose calculations in the kilovoltage energy range  

International Nuclear Information System (INIS)

A number of procedures in diagnostic radiology and cardiology make use of long exposures to x-rays from fluoroscopy units. Although numerous studies have been performed to measure or calculate skin dose from these procedures, there have only been a handful of studies to determine the dose to the other organs. This thesis was focused on devising a method to calculate the absorbed dose to underlying tissues and organs. The work was performed in several stages. First, a commercial convolution/superposition-based treatment planning system used in radiation oncology was modified and complemented to make it usable with the low energies of x-rays used in diagnostic radiology. This required generation of energy deposition kernels in the kilovoltage energy range. The kernels were generated using the EGS4 Monte Carlo system of codes and added to the treatment planning system. The treatment planning system was ...

2001-03-01

475

The effects of energy non-monochromaticity of "1"1B ion beams on "1"1B diffusion  

International Nuclear Information System (INIS)

We have shown that energy contamination introduced by ion beam deceleration technology that is used to increase the beam currents available for low energy boron implants, can affect fabricated junctions adversely. A 4 keV "1"1B beam is extracted and retarded by a potential of -3.5 keV for 0.5 keV "1"1B implantation, or by a potential of -3.8 keV for 0.2 keV "1"1B implantation. Intentional beam contamination was introduced by turning off the retarding potential to allow the 4 keV "1"1B ions to irradiate Si wafers directly. The percentage of contamination, at levels of 0.1%, 0.2% and 0.3% was introduced. Rapid thermal annealing of all the implanted samples was performed under N_2 ambient at 1050 deg. C for 1 s. The dopant tail profiles themselves are not significant if the contamination levels are low. However, the much higher damage level coming from high energy contamination increases the transient enhanced diffusion of ...

2005-08-01

476

The Next Linear Collider: NLC2001  

Energy Technology Data Exchange (ETDEWEB)

Recent studies in elementary particle physics have made the need for an e{sup +}e{sup -} linear collider able to reach energies of 500 GeV and above with high luminosity more compelling than ever [1]. Observations and measurements completed in the last five years at the SLC (SLAC), LEP (CERN), and the Tevatron (FNAL) can be explained only by the existence of at least one particle or interaction that has not yet been directly observed in experiment. The Higgs boson of the Standard Model could be that particle. The data point strongly to a mass for the Higgs boson that is just beyond the reach of existing colliders. This brings great urgency and excitement to the potential for discovery at the upgraded Tevatron early in this decade, and almost assures that later experiments at the LHC will find new physics. But the next generation of experiments to be mounted by the world-wide particle physics community must not only find this new physics, they must find out what it ...

2002-01-14

477

Foreign wood fuel supply for power generation in the Netherlands. Final report  

Energy Technology Data Exchange (ETDEWEB)

In the Netherlands, the interest in biomass for electricity generation has increased, mainly due to environmental reasons. Currently, the Dutch energy sector is investigating technologies which can reduce CO{sub 2} emissions. The growth of biomass and its subsequent utilization for energy purposes circulates recycled atmospheric carbon and has no net discharge of CO{sub 2}. To reduce emissions from coal-fired power plants biomass co-firing options are investigated. After exhaustion of internal supplies of wood wastes and other residues an extra amount of 1.02 Mt{sub 20} would be needed. Two supply options exist: the use of internal energy crops and the import of biomass. Because production of energy crops in the Netherlands is a rather expensive option, biomass procurement and production outside the Netherlands is studied. Two countries were investigated for the possible import of biomass: Estonia and ...

1995-08-01

478

Ocean FUSRAP: feasibility of ocean disposal of materials from the Formerly Utilized Sites Remedial Action Progam (FUSRAP)  

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) of the Department of Energy is designed to identify and evaluate the radiological conditions at sites formerly used by the Corps of Engineers Manhattan Engineer District and the US Atomic Energy Commission. Where required, remedial action will be instituted to remove potential restrictions on the use of the sites due to residual low-level radioactive contamination. A total of 31 sites that may require remedial action has been identified. The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP soil and rubble which contains traces of natural radioactive materials. The initial focus has been on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of ...

1982-01-01

479

Ocean FUSRAP: feasibility of ocean disposal of materials from the Formerly Utilized Sites Remedial Action Progam (FUSRAP)  

International Nuclear Information System (INIS)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) of the Department of Energy is designed to identify and evaluate the radiological conditions at sites formerly used by the Corps of Engineers Manhattan Engineer District and the US Atomic Energy Commission. Where required, remedial action will be instituted to remove potential restrictions on the use of the sites due to residual low-level radioactive contamination. A total of 31 sites that may require remedial action has been identified. The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP soil and rubble which contains traces of natural radioactive materials. The initial focus has been on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of ...

480

Analysis of cost-effective pipe insulation requirements  

Energy Technology Data Exchange (ETDEWEB)

The proposed ASHRAE/IES Standard 90.1-1989R contains updated requirements for pipe insulation thicknesses developed on the basis of technical and economic principles. These requirements were determined based on computer simulations of the annual energy loss through the insulation, first cost assumptions for the insulation, and economic assumptions of discount rate and energy escalation rate. In later work, the same tools were used to analyze the sensitivity of the cost-effective insulation level for piping insulation to variations in operating hours, ambient temperature, fluid temperature, and economic assumptions. These analyses were carried out using cost data for pipe insulation averaged across several sources. The results of the sensitivity study showed that system operating hours is a critical parameter in determining the cost-effective pipe insulation thicknesses. Although there is a lack of ...

1997-09-01

481

ASPEN simulation of environmental control processes, Task 1  

Energy Technology Data Exchange (ETDEWEB)

P.S. Lowell and Co., Inc. (Lowell and Co.) and Jay S. Dweck, Consultant, Inc. (JSD) under contract to the US Department of Energy (DOE) Morgantown Energy Technology Center (METC) have developed and implemented an aqueous electrolyte calculation capability into the ASPEN (Advanced System for Process Engineering) process simulator. This report documents the efforts of Task 1 which were to implement the basic calculational capability. Task 2 involves development of several unit operations models and demonstration of the models in simulating environmental control processes in coal gasification and shale oil processing plants. Task 1 of the project involved several subtasks: selection of a chemical equilibrium algorithm; selection of activity coefficient algorithms; selection of species for inclusion in the initial implementation; collection of required data for the selected species; regression of parameters not found in the ...

1986-07-01

482

RECOVERY ACT: DYNAMIC ENERGY CONSUMPTION MANAGEMENT OF ROUTING TELECOM AND DATA CENTERS THROUGH REAL-TIME OPTIMAL CONTROL (RTOC): Final Scientific/Technical Report  

Science.gov (United States)

This final scientific report documents the Industrial Technology Program (ITP) Stage 2 Concept Development effort on Data Center Energy Reduction and Management Through Real-Time Optimal Control (RTOC). Society is becoming increasingly dependent on information technology systems, driving exponential growth in demand for data center processing and an insatiable appetite for energy. David Raths noted, 'A 50,000-square-foot data center uses approximately 4 megawatts of power, or the equivalent of 57 barrels of oil a day1.' The problem has become so severe that in some cases, users are giving up raw performance for a better balance between performance and energy efficiency. Historically, power systems for data centers were crudely sized to meet maximum demand. Since many servers operate at 60%-90% of maximum power while only utilizing an average of 5% to 15% of their capability, there are huge inefficiencies ...

2011-06-30

483

Secure data communication for safeguards implementation  

International Nuclear Information System (INIS)

Full text: Secure, reliable and cost-effective communications are becoming an increasingly important tool for safeguards verification. This trend began with the initiation of remote monitoring implementation, where secure and cost effective data communications were required both to satisfy the confidentiality requirements of Member States and in order to meet the rigorous data authenticity requirements which allow the International Atomic Energy Agency (IAEA) to draw credible and independent conclusions. In addition, the implementation of additional protocols and integrated safeguards increases the importance of information (obtained in the course of an inspection, visit, complementary access or design information verification) being analyzed and corroborated with other information sources stored at IAEA Headquarters or Regional Offices, often while the inspector is still on-site. This ...

2006-10-16

484

Oak Ridge National Laboratory Waste Management Plan, fiscal year 1994. Revision 3  

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5820.2A was promulgated in final form on September 26, 1988. The order requires heads of field organizations to prepare and to submit updates on the waste management plans for all operations under their purview according to the format in Chap. 6, {open_quotes}Waste Management Plan Outline.{close_quotes} These plans are to be submitted by the DOE Oak Ridge Operations Office (DOE-ORO) in December of each year and distributed to the DP-12, ES&H-1, and other appropriate DOE Headquarters (DOE-HQ) organizations for review and comment. This document was prepared in response to this requirement for fiscal year (FY) 1994. The Oak Ridge National Laboratory (ORNL) waste management mission is reduction, collection, storage, treatment, and disposal of DOE wastes, generated primarily in pursuit of ORNL missions, in order to protect human health and safety and the environment. In carrying out this ...

1993-12-01

485

Maintenance implementation plan for solid waste management  

Energy Technology Data Exchange (ETDEWEB)

This Maintenance Implementation Plan (MIP)was developed for implementation of the U.S. Department of Energy (DOE) Order 4330.4A, A Maintenance Implementation Program (DOE 1990) which has been replaced by 4330.4B (DOE 1994) at the Hanford Site SWM complex. It addresses maintenance functions associated with SWM, which includes the field operational group and the facilities operational group. An assessment of the existing maintenance programs for SWM was performed, and the results of this assessment were evaluated to determine corrective actions required to bring Solid Waste Maintenance into compliance with the order. The objective of this MIP is to provide baseline information for the control and execution of SWM Maintenance activities relative to the requirements of Order 4330.4B, Chapter II. (Nuclear Facilities) It also describes actions that are planned to achieve compliance. Section 2.0 of this MIP summarizes the mission, ...

1996-06-27

486

Federal Facility Agreement plans and schedules for liquid low-level radioactive waste tank systems at Oak Ridge National Laboratory, Oak Ridge, Tennessee  

Energy Technology Data Exchange (ETDEWEB)

The Superfund Amendments and Reauthorization Act of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) requires a Federal Facility Agreement (FFA) for federal facilities placed on the National Priorities List. The Oak Ridge Reservation was placed on that list on December 21, 1989, and the agreement was signed in November 1991 by the Department of Energy Oak Ridge Field Office (DOE-OR), the US Environmental Protection Agency (EPA)-Region IV, and the Tennessee Department of Environment and Conservation (TDEC). The effective date of the FFA was January 1, 1992. Section 9 and Appendix F of the agreement impose design and operating requirements on the Oak Ridge National Laboratory (ORNL) liquid low-level radioactive waste (LLLW) tank systems and identify several plans, schedules, and assessments that must be submitted to EPA/TDEC for review or approval. The initial issue of this document in March ...

1993-06-01

487

Expert-systems application to power network security analysis  

Energy Technology Data Exchange (ETDEWEB)

In abnormal conditions, the operator's ability to deal with a large volume of data, and initiate the most appropriate remedial action is a fundamental concern in the design of energy control centers. Once a severe disruption has occurred in the power network, a series of tasks are required before the operator can make any decisions. Many of these functions involve computational efforts, and require a long period of processing time. The application of a wrong set of information by the operator may result in a catastrophic recovery situation. Also, as the system becomes larger, the required time for these tasks grows significantly and the operator may have very little time to analyze the contingency and issue a proper decision. These facts have led to the conclusion that a computer driven decision making mechanism will help the operator perform duties with minimum flaws and maximum efficiency. ...

1989-01-01

488

Automated real-time testing (ARTT) for embedded control systems (ECS).  

Energy Technology Data Exchange (ETDEWEB)

Many of today's automated real-time testing systems for embedded systems were developed using expensive custom hardware and software. In this article they describe how to use commercially available off-the-shelf hardware and software to design and develop an automated real-time test systems for Embedded Programmable Logic Controller (PLC) Based Control Systems. The system development began with the implementation of the VALI/TEST Pro testing methodology as a means for structuring the testing. Using this methodology, they were able to decompose system requirement documents for a Personnel Safety System (PSS) into its high, intermediate and detail level requirements. next, the validation procedures for the PSS system were decomposed into testing units called builds, test runs and test cases. To measure the PSS system's test coverage three levels of system requirements were mapped to their respective unit ...

2001-08-09

489

Analysis and decision document in support of acquisition of steam supply for the Hanford 200 Area  

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) is now evaluating its facility requirements in support of its cleanup mission at Hanford. One of the early findings is that the 200-Area steam plants, constructed in 1943, will not meet future space heating and process needs. Because the 200 Area will serve as the primary area for waste treatment and long-term storage, a reliable steam supply is a critical element of Hanford operations. This Analysis and Decision Document (ADD) is a preliminary review of the steam supply options available to the DOE. The ADD contains a comprehensive evaluation of the two major acquisition options: line-term versus privatization. It addresses the life-cycle costs associated with each alternative, as well as factors such as contracting requirements and the impact of market, safety, security, and regulatory issues. Specifically, this ADD documents current and future steam requirements for ...

1992-02-01

490

Parametric study of radiative cooling of solid antihydrogen. Master's thesis  

Energy Technology Data Exchange (ETDEWEB)

A computer model of cryogenic system for storing solid antimatter is used to explore the radiative cooling-power requirements for long-term antimatter storage. If vacuum-chamber pressures as low as 10 to -18th power torr can be reached, and the rest of the large set of assumptions is valid, milligram quantities of solid antimatter could be stored indefinitely at 1.5 K using cooling powers of less than a microwatt. Many of the assumptions made are problematic and need verification, as they could potentially change the results greatly. The system modeled is a sphere of solid anti-parahydrogen at 1.5 K or below levitated in a spherical cryogenic vacuum chamber. The free matter gas in the chamber is assumed to be molecular hydrogen, and sublimation of both matter and antimatter is assumed to be negligible. The antihydrogen is assumed to be in thermal equilibrium, although annihilation-energy deposition is localized and hydrogen's ...

1989-03-01

491

One-class classifiers and their application to synthetic aperture radar target recognition  

Energy Technology Data Exchange (ETDEWEB)

Target recognition requires the ability to distinguish targets from non-targets, a capability called one-class generalization. To function as a one-class classifier, a neural network must have three types of generalization: within-class, between-class, and out-of-class. We discuss these three types of generalization and identify neural network architectures that meet these requirements. We have applied our one-class classifier ideas to the problem of automatic target recognition in synthetic aperture radar. We have compared three neural network algorithms: Carpenter and Grossberg`s algorithmic version of the Adaptive Resonance Theory (ART-2A), Kohonen`s Learning Vector Quantization (LVQ), and Reilly and Cooper`s Restricted Columb Energy network (RCE). The ART 2-A neural network has given the best results, with 100% within-class, and out-of-class generalization. Experiments show that the network`s performance is sensitive to ...

1992-10-01

492

One-class classifier networks for target recognition applications  

Energy Technology Data Exchange (ETDEWEB)

Target recognition requires the ability to distinguish targets from non-targets, a capability called one-class generalization. Many neural network pattern classifiers fail as one-class classifiers because they use open decision boundaries. To function as one-class classifier, a neural network must have three types of generalization: within-class, between-class, and out-of-class. We discuss these three types of generalization and identify neural network architectures that meet these requirements. We have applied our one-class classifier ideas to the problem of automatic target recognition in synthetic aperture radar. We have compared three neural network algorithms: Carpenter and Grossberg`s algorithmic version of the Adaptive Resonance Theory (ART-2A), Kohonen`s Learning Vector Quantization (LVQ), and Reilly and Cooper`s Restricted Coulomb Energy network (RCE). The ART 2-A neural network gives the best results, with 100% ...

1993-01-01

493

Innovative coke oven gas cleaning system for retrofit applications. Volume 1, Public design report  

Energy Technology Data Exchange (ETDEWEB)

This Public Design Report provides, in a single document, available nonproprietary design -information for the ``Innovative Coke Oven Gas Cleaning System for Retrofit Applications`` Demonstration Project at Bethlehem Steel Corporation`s Sparrows Point, Maryland coke oven by-product facilities. This project demonstrates, for the first time in the United States, the feasibility of integrating four commercially available technologies (processes) for cleaning coke oven gas. The four technologies are: Secondary Gas Cooling, Hydrogen Sulfide and Ammonia Removal, Hydrogen Sulfide and Ammonia Recovery, and Ammonia Destruction and Sulfur Recovery. In addition to the design aspects, the history of the project and the role of the US Department of,Energy are briefly discussed. Actual plant capital and projected operating costs are also presented. An overview of the integration (retrofit) of the processes into the existing plant is presented and is followed by detailed ...

1994-05-24

494

Innovative coke oven gas cleaning system for retrofit applications. Environmental Monitoring program. Volume 1 - sampling progrom report. Baseline Sampling Program report  

Energy Technology Data Exchange (ETDEWEB)

Bethlehem Steel Corporation (BSC), in conjunction with the Department of Energy (DOE) is conducting a Clean Coal Technology (CCT) project at its Sparrows Point, Maryland Coke Oven Plant. This innovative coke oven gas cleaning system combines several existing technologies into an integrated system for removing impurities from Coke Oven Gas (COG) to make it an acceptable fuel. DOE provided cost-sharing under a Cooperative Agreement with BSC. This Cooperative Agreement requires BSC to develop and conduct and Environmental Monitoring Plan for the Clean Coal Technology project and to report the status of the EMP on a quarterly basis. It also requires the preparation of a final report on the results of the Baseline Compliance and Supplemental Sampling Programs that are part of the EMP and which were conducted prior to the startup of the innovative coke oven gas cleaning system. This report is the Baseline Sampling Program report.

1994-05-27

495

Ensuring the 50 year life of a fissile material container  

Energy Technology Data Exchange (ETDEWEB)

Sandia was presented with an opportunity in 1993 to design containers for the long term storage and transport of fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory which were tasked with developing the internal fixturing for the contents. The hardware is being supplied by Allied Signal Federal Manufacturing and Technologies, and the packaging will occur at Mason and Hangar Corporation`s Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required not only a rigorous design capable of meeting the long term storage and transportation requirements, but also resulted in development of a ...

1997-12-01

496

Cost guide. Volume 6. Cost-estimating methods and techniques  

Energy Technology Data Exchange (ETDEWEB)

There are many requirements for cost analysis and estimating within the Department of Energy (DOE). As projects go through the many stages of planning, source evaluation and selection, contracting, and construction, different estimating requirements exist and different techniques are available to the estimator. This cost guide illustrates how quantity takeoff estimating is performed when adequate design data are available, and it shows how statistics can be applied to obtain parametric cost estimates. Parametric techniques will become increasingly useful as the Department's cost data base and Cost Estimating Relationships (CERs) are developed. Other cost guides developed by the Independent Cost Estimating (ICE) Staff will be published and disseminated soon. The section on parametric cost estimating uses Department of Defense examples since the ICE Staff considered this information to be some of the best available ...

1982-05-01

497

An off-axis Cassegrain optimal design for short focal length parabolic solar concentrators  

Energy Technology Data Exchange (ETDEWEB)

The present work addresses an off-axis Cassegrain optical concentration system. The specific primary collector analyzed, a short focal length parabolic concentrator, is at the University of Florida`s Energy Park. A secondary hyperbolic reflective element was designed to redirect the solar radiation from the primary focal plane to an off-axis target on the polar axis of the primary concentrator. This ground level target will be required for planned experimental work. The analysis was performed using a numerical ray tracing procedure that incorporates both random and systematic errors due to slope and surface irregularities. The optimization process varied secondary element size, curvature, and offset angle, and yielded information required for optimum design. As a single secondary element was found impractical, three elements were designed for use at various time of the year. The numerical analysis predicts that typically 70 ...

1995-02-01

498

Advanced Neutron Source (ANS) Project progress report, FY 1994  

Energy Technology Data Exchange (ETDEWEB)

The President`s budget request for FY 1994 included a construction project for the Advanced Neutron Source (ANS). However, the budget that emerged from the Congress did not, and so activities during this reporting period were limited to continued research and development and to advanced conceptual design. A significant effort was devoted to a study, requested by the US Department of Energy (DOE) and led by Brookhaven National Laboratory, of the performance and cost impacts of reducing the uranium fuel enrichment below the baseline design value of 93%. The study also considered alternative core designs that might mitigate those impacts. The ANS Project proposed a modified core design, with three fuel elements instead of two, that would allow operation with only 50% enriched uranium and use existing fuel technology. The performance penalty would be 15--20% loss of thermal neutron flux; the flux would still just meet the minimum design requirement ...

1995-01-01