The coating layer structure of commercial chrome plates

International Nuclear Information System (INIS)

Chen, Sheng

2015-01-01

Highlights: • AES and XPS depth profiling analysis were used in the experiment. • The detailed coating layer structure of the commercial chrome plate was obtained. • Peak fitting method was used to investigate the chemical states of Cr in the coating. - Abstract: The surface and cross-sectional morphologies of the commercial chrome plate coating layer with the thickness of dozens of nanometers have been observed. To investigate the detailed structure of the coating layer, Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) combined with the low energy Ar + sputtering technique have been employed. Through careful analysis of experimental data, it can be obtained that the coating layer of commercial chrome plates is composed of four layers from top to bottom with different compositions

Study on creep-fatigue evaluation of chrome-molybdenum steel

International Nuclear Information System (INIS)

Aoto, Kazumi; Wada, Yusaku

1993-01-01

Though chrome-molybdenum steel has quite different basic material properties from austenitic stainless steel, the life fraction rule based on an advanced ductility exhaustion theory proposed for SUS304 is able to give proper prediction for creep-fatigue life of chrome-molybdenum steel. The applicability of the present evaluation method to chrome-molybdenum steel is validated by both mechanical study and micro-structural observation. The mechanism of creep-fatigue failure of Mod.9Cr-1Mo(NT) is one of the most controversial subjects among researchers. However, it is clarified in this report that creep-fatigue damage of this material under actual loading conditions is dominated by creep-cavitation of grain boundaries as same way as that of austenitic stainless steel. Furthermore, for the life reduction of low cycle fatigue of chrome-molybdenum steel with compression-side strain hold, both effects of mean stress and oxide-wedge are denied and it is insisted that the acceleration of fatigue-crack propagation is occurred by oxide-progress location and its thickness. (author)

Improvement of exhaustion and fixation of chrome tan by hydroxy organic acids

International Nuclear Information System (INIS)

Nashy, E.H.A.; Khedr, M.H.; EL-Sayed, N.H.

2005-01-01

Chrome tan is the most important tanning agent in the tanning industry, but it causes extreme pollution due to the incomplete exhaustion of the serious chrome cations in tanning bath. The exhaustion and fixation of chrome tan were improved in this study through treatment of delimed hide with three carboxylic acids named citric, malic and tartaric acids before exposure to tanning process. The process was optimized taking into the account the shaking rate, chrome concentration (%), initial ph, acids concentration, and temperature and contact time. The optimum conditions for exhaustion, fixation, shrinkage temperature as well as skin quality showed that agitation rate of 150 rpm, chrome concentration of 16%, initial ph of 8.5, acid concentration of 3% tartaric acid, temperature of 35 degree C and contact time of 24 hr.The best results obtained are 88% exhaustion, 88.32% fixation and 106 degree C shrinkage temperature in aqueous medium

Molecular spectroscopic study for suggested mechanism of chrome tanned leather

Science.gov (United States)

Nashy, Elshahat H. A.; Osman, Osama; Mahmoud, Abdel Aziz; Ibrahim, Medhat

2012-03-01

Collagen represents the structural protein of the extracellular matrix, which gives strength of hides and/or skin under tanning process. Chrome tan is the most important tanning agent all over the world. The methods for production of leather evolved over several centuries as art and engineering with little understanding of the underlying science. The present work is devoted to suggest the most probable mechanistic action of chrome tan on hide proteins. First the affect of Cr upon hide protein is indicated by the studied mechanical properties. Then the spectroscopic characterization of the hide protein as well as chrome tanned leather was carried out with Horizontal Attenuated Total Reflection (HATR) FT-IR. The obtained results indicate how the chromium can attached with the active sites of collagen. Molecular modeling confirms that chromium can react with amino as well as carboxylate groups. Four schemes were obtained to describe the possible interactions of chrome tan with hide proteins.

Qualification and Flight Test of Non-Chrome Primers for C-130 Aircraft

Science.gov (United States)

2011-08-17

system  Significant hexavalent chrome reduction in finish system  Potential exposure level of spray applied chromated conversion coating not as...Lockheed Martin Aeronautics Company Qualification and Flight Test of Non- Chrome Primers for C-130 Aircraft Scott Jones Lockheed Martin...00-2011 to 00-00-2011 4. TITLE AND SUBTITLE Qualification and Flight Test of Non- Chrome Primers for C-130 Aircraft 5a. CONTRACT NUMBER 5b. GRANT

Hexavalent Chrome Free Coatings for Electronics: Electromagnetic Interference (EMI) Shielding Effectiveness (SE)

Science.gov (United States)

Kessel, Kurt R.

2016-01-01

Determine the suitability of trivalent chromium conversion coatings that meet the requirements of MIL-DTL-5541, Type II, for use in applications where high-frequency electrical performance is important. Evaluate the ability of hexavalent chrome free pretreated aluminum to form adequate EMI seals, and maintain that seal while being subjected to harsh environmental conditions. Assess the performance of trivalent chromium pretreatments against a known control hexavalent chrome pretreatment before and after they have been exposed to a set of environmental conditions. It is known that environmental testing causes a decrease in shielding effectiveness when hexavalent chrome pretreatments are used (Alodine 1200s). Need to determine how shielding effectiveness will be affected with the use of hexavalent chrome free pretreatments. Performance will be assessed by evaluating shielding effectiveness (SE) test data from a variety of test samples comprised of different aluminum types and/or conversion coatings. The formation of corrosion will be evaluated between the mating surfaces and gasket to assess the corrosion resistant properties of the pretreatments, comparing the hexavalent control to the hexavalent chrome free pretreatments.

Hexavalent Chrome Free Coatings for Electronics Applications: Joint Test Report

Science.gov (United States)

Rothgeb, Matt; Kessel, Kurt

2013-01-01

The overall objective of the Hexavalent Chrome Free Coatings for Electronics Applications project is to evaluate and test pretreatments not containing hexavalent chrome in avionics and electronics housing applications. This objective will be accomplished by testing strong performing coating systems from prior NASA and DoD testing or new coating systems as determined by the stakeholders.

THE CHROME-TANNED GOAT LEATHER FOR HIGH QUALITY OF BATIK

Directory of Open Access Journals (Sweden)

W. Pancapalaga

2015-09-01

Full Text Available in which the first stage aimed to evaluate sodium silica as batik wax releasing agent on chrome leather.Completely randomized design (CRD was applied in this study. The concentration of sodium silica wastreated as treatments, in which Tl = 0, T2 = 2 g/L, T3: 4 g/L and T4 = 6 g/L. The second stage of thestudy was aimed to evaluate the type of dye used in batik method dyeing on chrome-tanned goat leather.CRD was used and the treatments were types of dye, i.e. T'1 = acid, T'2= indigosol, T'3 = napthol, T'4 =remazol. In both studies, 9 replicates were applied for each treatment. The use of sodium silicateconcentration of 2 g/L resulted in the percentage of release wax of 91.4% and did not degrade the qualityof chrome leather. The type of acid dyes and naphthol provided the best adhesion and color brightnessand resistance to washing treatment, water, sweat, bend, and rub at 4/5 to 5 on a scale of gray. Inconclusion, chrome tanned goat leather with batik dyeing method was recommended to become one ofthe raw materials of leather goods.

Syndeformation Chrome Spinels Inclusions in the Plastically Deformed Olivine Aggregates (Kraka Ophiolites, the Southern Urals

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2015-12-01

Full Text Available This article presents the results of structural, petrographic, mineralogical and chemical studies of dunite veinlets in spinel peridotite from the Kraka ophiolites. It is demonstrated that plastic deformation of polycrystalline olivine, which form dunite, was accompanied by precipitation of impurities (aluminum and chrome as newly formed chrome spinels. The thinnest acicular inclusions of 0.3-0.5 micron thick are aligned in olivine grains along [010] axis. Bigger elongated irregular chrome spinel grains usually occur along grain and sub-grain olivine boundaries, and, occasionally, inside the grains along [100] axis. Alteration from the fine xenomorphic grains of chrome spinels to the bigger idiomorphic crystals was observed. Analogically to dynamic ageing (dispersion hardening in metals, the structural and chemical alterations in dunites are interpreted as deformation induced segregation of impurities. It is suggested that the euhedral chrome spinel grains typical for ophiolitic dunites were formed by coalescence and spheroidization. This process may be a key factor in the formation of ophiolitic chrome ore deposits.

Novel Chemical Process for Producing Chrome Coated Metal

OpenAIRE

Pelar, Christopher; Greenaway, Karima; Zea, Hugo; Wu, Chun-Hsien; Luhrs, Claudia C.; Phillips, Jonathan

2018-01-01

The article of record as published may be found at http://dx.doi.org/10.3390/ma11010078 This work demonstrates that a version of the Reduction Expansion Synthesis (RES) process, Cr-RES, can create a micron scale Cr coating on an iron wire. The process involves three steps. I. A paste consisting of a physical mix of urea, chrome nitrate or chrome oxide, and water is prepared. II. An iron wire is coated by dipping. III. The coated, and dried, wire is heated to ~800 ◦C for 10 min in a tube fu...

Electrodeposition of Nanocrystalline Co-P Coatings as a Hard Chrome Alternative (Briefing Charts)

Science.gov (United States)

2011-02-10

chrome plating utilizes chromium in the hexavalent state (Cr6+) Cr6+ is a known carcinogen and poses a health risk to operators OSHA lowered the Cr6+ PEL...from 52 µg/m3 to 5 µg/m3 8 Apr 09, Memorandum, DoD Directive Hexavalent Chromium Management Policy NAVAIR Cr6+ Authorization Process Hard Chrome ...Aerospace & Defense February 10, 2011 Electrodeposition of Nanocrystalline Co-P Coatings as a Hard Chrome Alternative Jack Benfer Co-PI NAVAIR

Treatment of hexavalent chrome by bacteria. Saikin ni yoru rokka kuromu no shori

Energy Technology Data Exchange (ETDEWEB)

Otake, H [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1993-08-01

A biological reduction method in which hazardous hexavalent chrome is reduced by bacteria is explained as one of the bioremediation technologies. Those bacteria are separated from active sludge in the urban sewage treatment plant. The hexavalent chrome-reducing bacteria were isolated by cultivating the sludge. They were Enterobacter cloacae which are intestinal bacteria. Then, they were named HO1 stock. As a result of analyzing the reduction mechanism, it was made clear that the function is localized in the cellular endosporium and that the reduction is made by utilizing the electronic transfer system of endosporium. Under both aerobic and anaerobic conditions, they convert the hexavalent chrome into the trivalent chrome outside the cells. As a result of test, it was known that 5mM hexavalent chrome can be treated in one day. A quick reduction was confirmed also through an experiment in which carbon source was added to the industrial wastewater. If used for the treatment of sludge/water contaminated by hexavalent chrome, the present reduction by bacteria has the following advantages: The highest reduction rate is given near pH=7 at ordinary temperatures. It is not necessary to add chemicals. Energy is not needed. It is a disadvantageous fact that the present bacteria, if exposed to oxygen, become inactive. 18 refs., 5 figs.

NASA and ESA Collaboration on Hexavalent Chrome Free Coatings

Science.gov (United States)

Greene, Brian

2017-01-01

Presentation on the NASA and ESA Collaboration on Hexavalent Chrome Free Coatings project. Project is in response to a Memorandum of Understanding between NASA and ESA Concerning Cooperation in the Field of Space Transportation - signed September 11, 2009. The National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA) have expressed mutual interest in pursuing cooperation in the areas of evaluating hexavalent chrome-free coatings, environmentally-preferable coatings for maintenance of launch facilities and ground support equipment, citric acid as an alternative to nitric acid for passivation of stainless steel alloys.

GSDO Program Hexavalent Chrome Alternatives: Final Pretreatments Test Report

Science.gov (United States)

Kessel, Kurt

2013-01-01

Hexavalent chrome free pretreatments should be considered for use on Ground Support Equipment (OSE) and Electrical Ground Support Equipment (EOSE). Both of the hexavalent chrome free pretreatments (Metalast TCP HF and SurTec 650C) evaluated by this project met, and in some instances exceeded, the requirements ofMIL-DTL-5541 "Chemical Conversion Coatings on Aluminum and Aluminum Alloys". For DC resistance measurements, both Metalast TCP HF and SurTec (!50C met initial requirements following assembly and in many cases continued to maintain passing readings for the duration of testing.

Selective coating for solar panels. [using black chrome and black nickel

Science.gov (United States)

Mcdonald, G. E. (Inventor)

1977-01-01

The energy absorbing properties of solar heating panels are improved by depositing a black chrome coating of controlled thickness on a specially prepared surface of a metal substrate. The surface is prepared by depositing a dull nickel on the substrate, and the black chrome is plated on this low emittance surface to a thickness between 0.5 micron and 2.5 microns.

Microstructural Evolution in Chroming Coatings Friction Pairs under Dry Sliding Test Conditions

Directory of Open Access Journals (Sweden)

Xin Wang

2018-01-01

Full Text Available The microstructures of subsurface layers of 20CrMnTi steel pins against chroming and nonchroming T10 under dry sliding tests were studied by means of OM (optical microscopy, XRD (X-ray diffraction, and SEM (scanning electron microscopy. Results showed that the chroming coating strengthened the disc surface and significantly affected microstructural evolution. Three layers—the matrix, deformation layer (DL, and surface layer (SL—formed in 20CrMnTi for the chroming T10. The matrix and deformation layer (DL formed in 20CrMnTi for the nonchroming T10. The formation of the microstructure was considered as a result of the shear deformation.

NASA TEERM Hexavalent Chrome Alternatives Projects

Science.gov (United States)

Kessel, Kurt; Rothgeb, Matt

2011-01-01

This slide presentation reviews the NASA project to select an alternative to hexavalent chrome in the aerospace industry. Included is a recent historic testing and research that the Agency has performed on (1) the external tank, (2) the shuttle orbiter, (3) the Shuttle Rocket Booster, and (4) the Space Shuttle Main Engine. Other related Technology Evaluation for Environmental Risk Mitigation (TEERM) projects are reviewed. The Phase I process of the project performed testing of alternatives the results are shown in a chart for different coating systems. International collaboration was also reviewed. Phase II involves further testing of pretreatment and primers for 6 and 12 months of exposure to conditions at Launch Pad and the beach. Further test were performed to characterize the life cycle corrosion of the space vehicles. A new task is described as a joint project with the Department of Defense to identify a Hex Chrome Free Coatings for Electronics.

Chemometrics models for assessment of oxidative stress risk in chrome-electroplating workers.

Science.gov (United States)

Zendehdel, Rezvan; Shetab-Boushehri, Seyed Vahid; Azari, Mansoor R; Hosseini, Vajihe; Mohammadi, Hamidreza

2015-04-01

Oxidative stress is the main cause of hexavalant chromium-induced damage in chrome electroplating workers. The main goal of this study is toxicity analysis and the possibility of toxicity risk categorizing in the chrome electroplating workers based on oxidative stress parameters as prognostic variables. We assessed blood chromium levels and biomarkers of oxidative stress such as lipid peroxidation, thiol (SH) groups and antioxidant capacity of plasma. Data were subjected to principle component analysis (PCA) and artificial neuronal network (ANN) to obtain oxidative stress pattern for chrome electroplating workers. Blood chromium levels increased from 4.42 ppb to 10.6 ppb. Induction of oxidative stress was observed by increased in lipid peroxidation (22.38 ± 10.47 μM versus 14.74 ± 4.82 μM, p chrome electroplaters. The result showed multivariate modeling can be interpreted as the induced biochemical toxicity in the workers exposed to hexavalent chromium. Different occupation groups were assessed on the basis of risk level of oxidative stress which could further justify proceeding engineering control measures.

Biodegradation of Crystal Violet by Agrobacterium radiobacter

DEFF Research Database (Denmark)

Parshetti, G.K.; Parshetti, S.G.; Telke, A.A.

2011-01-01

Violet (100 mg/L) was studied, maximum decolorization was observed with 15% inoculum concentration. A significant increase in the activities of laccase (184%) and aminopyrine Af-demethylase (300%) in cells obtained after decolorization indicated the involvement of these enzymes in decolorization process...... and phenol. We proposed the hypothetical metabolic pathway of Crystal Violet biodegradation by A. radiobacter. Phytotoxicity and microbial toxicity study showed that Crystal Violet biodegradation metabolites were less toxic to bacteria (A. radiobacter, P. aurugenosa and A. vinelandii) contributing to soil...

Electrochemical regeneration of chrome etching solution

NARCIS (Netherlands)

Andel, van Y.; Janssen, L.J.J.

2002-01-01

A metal surface is chromatized with a chromic acid solution to obtain a good adherence of polymer coatings. In this process Cr(VI) is reduced to Cr(III). The oxidation strength of the solution decreases during use. The chrome solution needs to be regenerated and purified. A new anode material,

21 CFR 589.1000 - Gentian violet.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Gentian violet. 589.1000 Section 589.1000 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS... Substances Prohibited From Use in Animal Food or Feed § 589.1000 Gentian violet. The Food and Drug...

SU-E-T-328: Dosimetric Impact of Cobalt-Chrome Stabilization Hardware in Paraspinal Radiation Therapy

International Nuclear Information System (INIS)

Tang, G; LoSasso, T; Saleh, Z; Mechalakos, J; Lim, S; Lovelock, D; Laufer, I; Bilsky, M; Yamada, J

2015-01-01

Purpose: Due to saturation, high density materials Result in an apparent density of 3.2 g/cm 3 in CT images. The true density of traditional titanium stabilization rods (∼4.4 g/cm 3 ) is typically ignored in treatment planning. This may not be acceptable for new cobalt-chrome rods with a density of 8.5 g/cm 3 . This study reports the dosimetric impact of cobalt-chrome rods in paraspinal radiotherapy. Methods: For titanium and cobalt-chrome rods, two planning studies were done for both IMRT and VMAT in Varian Eclipse using AAA. 1) The effect of planning without assigning the true rod density was assessed by comparing plans generated with the apparent density and recalculated with the true density for titanium and cobalt-chrome. 2) To test if TPS can compensate for high density rods during optimization. Furthermore, TPS calculation accuracy was verified using MapCheck for a single 20 x 10 cm 2 field. The MapCheck was incrementally shifted to achieve measurement resolution of 1 mm. Results: PTV coverage was ∼0.3% and ∼4.7% lower in plans that were recalculated with the true rod density of titanium and cobalt-chrome, respectively. PTV coverage can be maintained if the correct density is used in optimization. Measurements showed that TPS overestimated the dose locally by up to 11% for cobalt-chrome rods and up to 4% for titanium rods if the density is incorrect. With density corrected, maximum local differences of 6% and 3% were seen for cobalt-chrome and titanium rods, respectively. At 2 cm beneath a rod, electrons scattered from the side of the rod increased the lateral dose and diminished as depth increases. TPS was not able to account for this effect properly even with the true rod density assigned. Conclusion: Neglecting the true density of cobalt-chrome rods can cause under coverage to the PTV. Assigning the correct density during treatment planning can minimize unexpected decrease in PTV dose

Improvement of uptake of chrome tan on hide protein by basic oxides

International Nuclear Information System (INIS)

Nashya, E.H.A.; Aggiagh, A.E.; Khedra, M.H.; El-Sayeda, N.H.E.

2005-01-01

Three basic oxides were used to improve uptake of chrome tan as well as shrinkage temperature of the tanned leather. In addition, the skin quality is one of the most important factors taking into consideration. Three basic oxides, named magnesium oxide, manganese oxide and sodium bicarbonate. The process was optimized taking into the account the shaking rate, chrome concentration (%), initial ph, basic oxides concentration, temperature and contact time. The optimum conditions for exhaustion, fixation, shrinkage temperature as well as skin quality showed that agitation rate of 150 rpm, chrome concentration of 16%, initial ph of 2.5, basic oxide concentration of 4% magnesium oxide, temperature of 35 degree C and contact time of 24 hr. The best results obtained are 88% exhaustion, 90.03% fixation and 109 degree C shrinkage temperature in aqueous medium

Preparation of high exhaust chrome from leather shavings and hydrocarbons with its application in leather processing for green tanning technology

International Nuclear Information System (INIS)

Nawaz, H.R.; Solangi, B.A.; Nadeem, U.; Zehra, B.

2010-01-01

The use of chrome in tanning has made the remarkable advances to achieve the best quality and quantity of leather. But the chrome tanning process is associated with the generation of heavy metal containing solid wastes and toxic effluents. To solve the environmental issues we emphasized on the development of high exhaust chrome complex from chrome containing leather wastes that could minimize the toxic effluents up to negligible limit. Therefore in the synthetic process of chrome tanning material, the chrome shavings and the hydrocarbons have been utilized as a reductant as well as the potential masking intermediates. These chrome tanning materials have been prepared using leather shavings alone in product A, partial replacement of shavings by hydrocarbons for product B and then replacement of hydrocarbons by molasses for product C. The materials have been employed for the tanning of goat skins parallel to the commercial basic chromium sulfate (BCS). (author)

Chrome - Free Aluminum Coating System

Science.gov (United States)

Bailey, John H.; Gugel, Jeffrey D.

2010-01-01

This slide presentation concerns the program to qualify a chrome free coating for aluminum. The program was required due to findings by OSHA and EPA, that hexavalent chromium, used to mitigate corrosion in aerospace aluminum alloys, poses hazards for personnel. This qualification consisted of over 4,000 tests. The tests revealed that a move away from Cr+6, required a system rather than individual components and that the maximum corrosion protection required pretreatment, primer and topcoat.

Confirmatory analysis of malachite green, Leucomalachite green, crystal violet and leucocrystal violet in salmon by liquid chromatography-tandem mass spectrometry

NARCIS (Netherlands)

Dowling, A.P.G.; Mulder, P.P.J.; Duffy, C.; Regan, L.; Smyth, M.R.

2007-01-01

A method has been developed to analyse for malachite green (MG), leucornalachite green (LMG), crystal violet (CV) and leucocrystal violet (LCV) residues in salmon. Salmon samples were extracted with acetonitrile:Mclllvain pH 3 buffer (90: 10 v/v), sample extracts were purified on a Bakerbond strong

Wear and creep of highly crosslinked polyethylene against cobalt chrome and ceramic femoral heads.

Science.gov (United States)

Galvin, A L; Jennings, L M; Tipper, J L; Ingham, E; Fisher, J

2010-10-01

The wear and creep characteristics of highly crosslinked ultrahigh-molecular-weight polyethylene (UHMWPE) articulating against large-diameter (36mm) ceramic and cobalt chrome femoral heads have been investigated in a physiological anatomical hip joint simulator for 10 million cycles. The crosslinked UHMWPE/ceramic combination showed higher volume deformation due to creep plus wear during the first 2 million cycles, and a steady-state wear rate 40 per cent lower than that of the crosslinked UHMWPE/cobalt chrome combination. Wear particles were isolated and characterized from the hip simulator lubricants. The wear particles were similar in size and morphology for both head materials. The particle isolation methodology used could not detect a statistically significant difference between the particles produced by the cobalt chrome and alumina ceramic femoral heads.

Development of technology of complex aluminum-silicon-chrome alloy with utilization of off grade raw materials

Directory of Open Access Journals (Sweden)

A. Mekhtiev

2015-01-01

Full Text Available Experimental studies on obtaining a complex aluminum-silicon-chrome alloy (FASCh from Karaganda high-ash coals and high-carbon ferrochromefines were carried out. A method for smelting low-carbon ferrochrome using aluminum-silicon-chrome alloy as a reductant is suggested.

NASA TEERM Hexavalent Chrome Alternatives Projects

Science.gov (United States)

Kessel, Kurt R.; Rothgeb, Matthew

2011-01-01

The overall objective of the Hex Chrome Free Coatings for Electronics project is to evaluate and test pretreatment coating systems not containing hexavalent chrome in avionics and electronics housing applications. This objective will be accomplished by testing strong performing coating systems from prior NASA and DoD testing or new coating systems as determined by the stakeholders. The technical stakeholders have agreed that this protocol will focus specifically on Class 3 coatings. Original Equipment Manufacturers (OEMs), depots, and support contractors have to be prepared to deal with an electronics supply chain that increasingly provides parts with lead-free finishes, some labeled no differently and intermingled with their SnPb counterparts. Allowance of lead-free components presents one of the greatest risks to the reliability of military and aerospace electronics. The introduction of components with lead-free terminations, termination finishes, or circuit boards presents a host of concerns to customers, suppliers, and maintainers of aerospace and military electronic systems such as: 1. Electrical shorting due to tin whiskers 2. Incompatibility of lead-free processes and parameters (including higher melting points of lead-free alloys) with other materials in the system 3. Unknown material properties and incompatibilities that could reduce solder joint reliability

Study of skin and mucous membrane disorders among workers engaged in the sodium dichromate manufacturing industry and chrome plating industry.

Science.gov (United States)

Singhal, Vijay Kumar; Deswal, Balbir Singh; Singh, Bachu Narayan

2015-01-01

Inhalation of dusts and fumes arising during the manufacture of sodium dichromate from chrome ore, chromic acid mist emitted during electroplating, and skin contact with chromate produce hazards to workers. (1) To elucidate the prevalence of skin and mucous membrane disorders among the workers engaged in the sodium dichromate manufacturing industry and chrome plating industry. (2) To know the relationship of prevalence with the duration of exposure to chrome mist, dust, and fumes. A cross-sectional study was conducted among all the workers engaged in sodium dichromate manufacturing and chrome plating from several industries situated near the Delhi-Haryana border in the districts of Faridabad and Sonepat of Haryana, India from January 01, 2014 to December 31, 2014. All the workers available from the concerned industries for the study were interviewed and medically examined after obtaining their informed consent. A total of 130 workers comprising 66 workers from the sodium dichromate manufacturing industry and 64 workers from the chrome plating industry were examined on a pretested schedule. Descriptive statistical methods (proportions, relative risk, and Chi-square test of significance with P value analyzed using Epi Info version 7). All the workers were found to be males and of the adult age group. Out of the total examined, 69.69% and 56.22% of the workers had disorders of the nasal mucous membrane in the sodium dichromate manufacturing industry and the chrome plating industry, respectively. 42.42% and 28.22% of the workers had perforation of the nasal septum in the sodium dichromate manufacturing industry and chrome plating industry, respectively. 6.06% and 3.12% workers had skin ulcers in the sodium dichromate manufacturing industry and chrome plating industry, respectively. Nasal irritation and rhinorrhea were the most commonly found symptoms in both the processes. 48.48% and 90.52% of the workers were using hand gloves in the sodium dichromate manufacturing

Synthesis of Cu Doped ZnO Nanostructures for Ultra Violet Sensing

Directory of Open Access Journals (Sweden)

Nazar Abbas SHAH

2015-03-01

Full Text Available This paper mainly focused on the synthesis of zinc oxide nanostructures, their characterization and their ultra violet light sensing response at room temperature. Nanowires, nanobelts and nanosheets were synthesized by varying doping material copper by using vapor transport technique governed by the vapor-liquid-solid or vapor-solid mechanisms. The structural, morphological and optical characterization was carried out using X-ray diffraction, scanning electron microscopy, energy dispersive X-Ray and ultra violet visible spectroscopy techniques. Finally the ultra violet light sensing response of these nanostructures was observed by using Keithley meter. The high ultra violet photosensitivity and fast response time justifies the effective utilization of these ZnO nanostructures as ultra violet sensors in different areas.

Safety evaluation of traces of nickel and chrome in cosmetics: The case of Dead Sea mud.

Science.gov (United States)

Ma'or, Ze'evi; Halicz, Ludwik; Portugal-Cohen, Meital; Russo, Matteo Zanotti; Robino, Federica; Vanhaecke, Tamara; Rogiers, Vera

2015-12-01

Metal impurities such as nickel and chrome are present in natural ingredients-containing cosmetic products. These traces are unavoidable due to the ubiquitous nature of these elements. Dead Sea mud is a popular natural ingredient of cosmetic products in which nickel and chrome residues are likely to occur. To analyze the potential systemic and local toxicity of Dead Sea mud taking into consideration Dead Sea muds' natural content of nickel and chrome. The following endpoints were evaluated: (Regulation No. 1223/20, 21/12/2009) systemic and (SCCS's Notes of Guidance) local toxicity of topical application of Dead Sea mud; health reports during the last five years of commercial marketing of Dead Sea mud. Following exposure to Dead Sea mud, MoS (margin of safety) calculations for nickel and chrome indicate no toxicological concern for systemic toxicity. Skin sensitization is also not to be expected by exposure of normal healthy skin to Dead Sea mud. Topical application, however, is not recommended for already nickel-or chrome-sensitized persons. As risk assessment of impurities present in cosmetics may be a difficult exercise, the case of Dead Sea mud is taken here as an example of a natural material that may contain traces of unavoidable metals. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Optical Determination of Lead Chrome Green in Green Tea by Fourier Transform Infrared (FT-IR Transmission Spectroscopy.

Directory of Open Access Journals (Sweden)

Xiaoli Li

Full Text Available The potential of Fourier transform infrared (FT-IR transmission spectroscopy for determination of lead chrome green in green tea was investigated based on chemometric methods. Firstly, the qualitative analysis of lead chrome green in tea was performed based on partial least squares discriminant analysis (PLS-DA, and the correct rate of classification was 100%. And then, a hybrid method of interval partial least squares (iPLS regression and successive projections algorithm (SPA was proposed to select characteristic wavenumbers for the quantitative analysis of lead chrome green in green tea, and 19 wavenumbers were obtained finally. Among these wavenumbers, 1384 (C = C, 1456, 1438, 1419(C = N, and 1506 (CNH cm-1 were the characteristic wavenumbers of lead chrome green. Then, these 19 wavenumbers were used to build determination models. The best model was achieved by least squares support vector machine (LS-SVMalgorithm with high coefficient of determination and low root-mean square error of prediction set (R2p = 0.864 and RMSEP = 0.291. All these results indicated the feasibility of IR spectra for detecting lead chrome green in green tea.

A conceptual model for determining career choice of CHROME alumna based on farmer's conceptual models

Science.gov (United States)

Moore, Lisa Simmons

This qualitative program evaluation examines the career decision-making processes and career choices of nine, African American women who participated in the Cooperating Hampton Roads Organization for Minorities in Engineering (CHROME) and who graduated from urban, rural or suburban high schools in the year 2000. The CHROME program is a nonprofit, pre-college intervention program that encourages underrepresented minority and female students to enter science, technically related, engineering, and math (STEM) career fields. The study describes career choices and decisions made by each participant over a five-year period since high school graduation. Data was collected through an Annual Report, Post High School Questionnaires, Environmental Support Questionnaires, Career Choice Questionnaires, Senior Reports, and standardized open-ended interviews. Data was analyzed using a model based on Helen C. Farmer's Conceptual Models, John Ogbu's Caste Theory and Feminist Theory. The CHROME program, based on its stated goals and tenets, was also analyzed against study findings. Findings indicated that participants received very low levels of support from counselors and teachers to pursue STEM careers and high levels of support from parents and family, the CHROME program and financial backing. Findings of this study also indicated that the majority of CHROME alumna persisted in STEM careers. The most successful participants, in terms of undergraduate degree completion and occupational prestige, were the African American women who remained single, experienced no critical incidents, came from a middle class to upper middle class socioeconomic background, and did not have children.

Synthesis of Citric-Acrylate Oligomer and its in-Situ Reaction with Chrome Tanned Collagen (hide powder)

International Nuclear Information System (INIS)

Haroun, A.A.; Masoud, R.A.; Bronco, S.; Ciardelli, F.

2005-01-01

The purpose of this study was to formulate the new combined system of acrylic and citric acids, which has been prepared by free radical polymerization and esterification reaction at the same time to form citric acrylate (CAC) oligomer through ester linkage and low molecular weight (Mw 2241), in compared with polyacrylic acid. The chemical structure and the reaction mechanism of this oligomer were confirmed by different spectroscopic tools (1 H , 13 C-NMR, ATR-IR), gel permeation chromatography and thermogravimetric analysis (TGA/DTA). The problem of the effect of the masking agents in the chrome tanning of the collagen and the pickling of the hide has been approached from the study of the hydrothermal and mechanical properties, using this new eco-friendly oligomer, which was carried out in-situ treated/grafted chrome tanned collagen (hide powder), and pickled hide. The microemulsion grafting copolymerization of (CAC) using 2.2-azo-bis isobutyronitrile (ABIN), via direct coupling reaction, onto the chrome tanned collagen showed that the free amino groups of the collagen were considered to be a potential site for the in-situ reaction with (CAC) oligomer. Also, using of citric-acrylate (CAC) oligomer, during chrome tanning of leather, instead of the traditional strong acids (sulfuric, hydrochloric and formic) resulted in significant improvement in chrome exhaustion and physical properties

Le chrome en milieu marin

OpenAIRE

Chiffoleau, Jean-francois

1994-01-01

Le présent document constitue une synthèse des connaissances sur le cycle biogéochimique du chrome. Les sources naturelles et anthropiques sont étudiées, les échanges entre les différents compartiments géochimiques sont évalués, avec une attention particulière portée à la quantification des apports aussi bien des fleuves que de l'atmosphère au milieu marin. Les niveaux de concentration dans ces compartiments sont évalués, et montrent que l'on rencontre dans certaines régions des contamination...

Validation of HVOF WC/Co Thermal Spray Coatings as a Replacement for Hard Chrome Plating on Aircraft Landing Gear

National Research Council Canada - National Science Library

Sartwell, Bruce

2004-01-01

.... However, chrome plating utilizes hexavalent chromium, which is a highly toxic carcinogen, and increasingly stringent environmental and worker-safety regulations are making chrome plating more expensive for the DoD...

Ni–Mo–Co ternary alloy as a replacement for hard chrome

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Meenu, E-mail: meenu_srivas@yahoo.co.uk; Anandan, C.; Grips, V.K. William

2013-11-15

Hard chrome is the most extensively used electroplated coating in the aerospace and automotive industries due to its attractive properties such as high hardness and excellent wear resistance. However, due to the health risks associated with the use of hexavalent chromium baths during electroplating, there is a need to identify an alternative to this coating. In this study a nickel–molybdenum alloy with cobalt as the alloying element has been developed. The coating was characterized for its micro hardness, wear resistance, coefficient of friction and corrosion resistance. The coating was also subjected to heat treatment at temperatures in the range of 200°–600 °C. It was observed that the micro hardness of Ni–Mo–Co (730 KHN) alloy coating under optimized conditions is apparently quiet similar to that of the most probable substitute Co–P (745 VHN) and hard chrome (800 VHN) coatings. The tribological properties like the wear rate and coefficient of friction of the 400 °C heat treated Ni–Mo–Co coating were noticed to be better compared to hard chrome coating. The electrochemical impedance and polarization studies showed that the corrosion resistance of heat treated Ni–Mo–Co alloy was better than as-deposited Ni–Mo–Co and Ni–Mo coating.

Ni–Mo–Co ternary alloy as a replacement for hard chrome

International Nuclear Information System (INIS)

Srivastava, Meenu; Anandan, C.; Grips, V.K. William

2013-01-01

Hard chrome is the most extensively used electroplated coating in the aerospace and automotive industries due to its attractive properties such as high hardness and excellent wear resistance. However, due to the health risks associated with the use of hexavalent chromium baths during electroplating, there is a need to identify an alternative to this coating. In this study a nickel–molybdenum alloy with cobalt as the alloying element has been developed. The coating was characterized for its micro hardness, wear resistance, coefficient of friction and corrosion resistance. The coating was also subjected to heat treatment at temperatures in the range of 200°–600 °C. It was observed that the micro hardness of Ni–Mo–Co (730 KHN) alloy coating under optimized conditions is apparently quiet similar to that of the most probable substitute Co–P (745 VHN) and hard chrome (800 VHN) coatings. The tribological properties like the wear rate and coefficient of friction of the 400 °C heat treated Ni–Mo–Co coating were noticed to be better compared to hard chrome coating. The electrochemical impedance and polarization studies showed that the corrosion resistance of heat treated Ni–Mo–Co alloy was better than as-deposited Ni–Mo–Co and Ni–Mo coating.

Elevated Frequencies of Micronuclei and other Nuclear Abnormalities of Chrome Plating Workers Occupationally Exposed to Hexavalent Chromium.

Science.gov (United States)

Sudha, S; Kripa, S K; Shibily, P; Shyn, J

2011-01-01

Biomonitoring provides a useful tool to estimate the genetic risk from exposure to genotoxic agents. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to hexavalent chromium by using micronuclei (MN) as a biomarker. This was a cross-sectional study and all participants were males. Both the exposed and control individuals were selected from Coimbatore, Southern India. Exfoliated buccal cells from 44 chrome plating workers and 40 age and sex matched control subjects were examined for MN frequency and nuclear abnormalities (NA) other than micronuclei, such as binucleates, broken eggs, karyorrhexis, karyolysis and pyknosis. Results showed statistically significant difference between chrome plating workers and control groups. MN and NA frequencies in chrome plating workers were significantly higher than those in control groups (p chrome plating workers are under risk of significant cytogenetic damage. Therefore, there is a need to educate those who work with heavy metals about the potential hazard of occupational exposure and the importance of using protective measures.

Weight of Polyethylene Wear Particles is Similar in TKAs with Oxidized Zirconium and Cobalt-chrome Prostheses

Science.gov (United States)

Kim, Jun-Shik; Huh, Wansoo; Lee, Kwang-Hoon

2009-01-01

Background The greater lubricity and resistance to scratching of oxidized zirconium femoral components are expected to result in less polyethylene wear than cobalt-chrome femoral components. Questions/purposes We examined polyethylene wear particles in synovial fluid and compared the weight, size (equivalent circle diameter), and shape (aspect ratio) of polyethylene wear particles in knees with an oxidized zirconium femoral component with those in knees with a cobalt-chrome femoral component. Patients and Methods One hundred patients received an oxidized zirconium femoral component in one knee and a cobalt-chrome femoral component in the other. There were 73 women and 27 men with a mean age of 55.6 years (range, 44–60 years). The minimum followup was 5 years (mean, 5.5 years; range, 5–6 years). Polyethylene wear particles were analyzed using thermogravimetric methods and scanning electron microscopy. Results The weight of polyethylene wear particles produced at the bearing surface was 0.0223 ± 0.0054 g in 1 g synovial fluid in patients with an oxidized zirconium femoral component and 0.0228 ± 0.0062 g in patients with a cobalt-chrome femoral component. Size and shape of polyethylene wear particles were 0.59 ± 0.05 μm and 1.21 ± 0.24, respectively, in the patients with an oxidized zirconium femoral component and 0.52 ± 0.03 μm and 1.27 ± 0.31, respectively, in the patients with a cobalt-chrome femoral component. Knee Society knee and function scores, radiographic results, and complication rate were similar between the knees with an oxidized zirconium and cobalt-chrome femoral component. Conclusions The weight, size, and shape of polyethylene wear particles were similar in the knees with an oxidized zirconium and a cobalt-chrome femoral component. We found the theoretical advantages of this surface did not provide the actual advantage. Level of Evidence Level I, therapeutic study. See the guidelines for Authors for a complete

Effect of gamma radiation on chrome-tanned sheepskin

International Nuclear Information System (INIS)

Kaldirimci, C.

1982-01-01

Effect of 60 γ-radiation on chrome-tanned, blue-stock sheepskin was investigated. Radiation was applied between 0.35-10.5 Mrad and the resultant physical and mechanical changes were observed. Radiation did not change the water adsorption capability of leather but caused significant reductions in shrinkage temperature and tensile strength. The correlations between dose and radiation hazards were determined. (author)

Total control of chromium in tanneries - thermal decomposition of filtration cake from enzymatic hydrolysis of chrome shavings.

Science.gov (United States)

Kocurek, P; Kolomazník, K; Bařinová, M; Hendrych, J

2017-04-01

This paper deals with the problem of chromium recovery from chrome-tanned waste and thus with reducing the environmental impact of the leather industry. Chrome-tanned waste was transformed by alkaline enzymatic hydrolysis promoted by magnesium oxide into practically chromium-free, commercially applicable collagen hydrolysate and filtration cake containing a high portion of chromium. The crude and magnesium-deprived chromium cakes were subjected to a process of thermal decomposition at 650°C under oxygen-free conditions to reduce the amount of this waste and to study the effect of magnesium removal on the resulting products. Oxygen-free conditions were applied in order to prevent the oxidation of trivalent chromium into the hazardous hexavalent form. Thermal decomposition products from both crude and magnesium-deprived chrome cakes were characterized by high chromium content over 50%, which occurred as eskolaite (Cr 2 O 3 ) and magnesiochromite (MgCr 2 O 4 ) crystal phases, respectively. Thermal decomposition decreased the amount of chrome cake dry feed by 90%. Based on the performed experiments, a scheme for the total control of chromium in the leather industry was designed.

Development of CMOS MEMS inductive type tactile sensor with the integration of chrome steel ball force interface

Science.gov (United States)

Yeh, Sheng-Kai; Chang, Heng-Chung; Fang, Weileun

2018-04-01

This study presents an inductive tactile sensor with a chrome steel ball sensing interface based on the commercially available standard complementary metal-oxide-semiconductor (CMOS) process (the TSMC 0.18 µm 1P6M CMOS process). The tactile senor has a deformable polymer layer as the spring of the device and no fragile suspended thin film structures are required. As a tactile force is applied on the chrome steel ball, the polymer would deform. The distance between the chrome steel ball and the sensing coil would changed. Thus, the tactile force can be detected by the inductance change of the sensing coil. In short, the chrome steel ball acts as a tactile bump as well as the sensing interface. Experimental results show that the proposed inductive tactile sensor has a sensing range of 0-1.4 N with a sensitivity of 9.22(%/N) and nonlinearity of 2%. Preliminary wireless sensing test is also demonstrated. Moreover, the influence of the process and material issues on the sensor performances have also been investigated.

The Use Level of Chrome Tannage For Rabbit Fur Leather Observed on Tearing Strength, Stitch Tearing Strength, Water Absorption and Organoleptic

Directory of Open Access Journals (Sweden)

Mustakim Mustakim

2012-02-01

Full Text Available The purpose of this study was to find out the appropiate of chrome tannage level for rabbit fur leather quality. The result were expected to contribute information for many people who relate with tanning technology, especialy about the use level of chrome tannage for fur leather quality and could as patern to hold further research.The material that used were 12 pieces of three months of rabbit skin. The method is Completely Randomized Design, consist of three treatments of chrome tannage (Chromosal B, they were : B1 (Chromosal B 6%, B2 (Chromosal B 8%, and B3 (Chromosal B 10%. Each of treatment hold on four replications. The variables which measured are tearing strength, stitch teraing strength, water absorption and organoleptic consist of “kekuatan bulu”’ “kerataan bulu” and “kelemasan kulit” in fur leather. Data was analysed by analysis variance followed by Duncan’s Multiple Range Test. The result of this research show that the use level of chromosal B give very significant influence among tearing strength, stitch tearing strength and water absorption. It gave significant influence among the organoleptic test. Based on the result, can be concluded that 10 percent of chrome tannage (chromosal B, produce the best result on tearing strength, stitch tearing strength, water absorption and organoleptic for “kekuatan bulu” and “kerataan bulu”. The incrase of chrome tannage offer will decrease the “kelemasan kulit” in fur leather and the best “kelemasan kulit” produced by the lowest chrome tannage offer, that was 6 percent of Chromosal B. The best quality of rabbit fur leather produced by 10 percent of chrome tannage offer.   Keywords: chrome, tannage, fur leather

Micropropagation of African violet (Saintpaulia ionantha Wendl.).

Science.gov (United States)

Shukla, Mukund; Sullivan, J Alan; Jain, Shri Mohan; Murch, Susan J; Saxena, Praveen K

2013-01-01

Micropropagation is an important tool for rapid multiplication and the creation of genetic variability in African violets (Saintpaulia ionantha Wendl.). Successful in vitro propagation depends on the specific requirements and precise manipulation of various factors such as the type of explants used, physiological state of the mother plant, plant growth regulators in the culture medium, and growth conditions. Development of cost-effective protocols with a high rate of multiplication is a crucial requirement for commercial application of micropropagation. The current chapter describes an optimized protocol for micropropagation of African violets using leaf explants obtained from in vitro grown plants. In this process, plant regeneration occurs via both somatic embryogenesis and shoot organogenesis simultaneously in the explants induced with the growth regulator thidiazuron (TDZ; N-phenyl-N'-1,2,3-thidiazol-5-ylurea). The protocol is simple, rapid, and efficient for large-scale propagation of African violet and the dual routes of regeneration allow for multiple applications of the technology from simple clonal propagation to induction or selection of variants to the production of synthetic seeds.

SUPERFUND TREATABILITY CLEARINGHOUSE: SOIL STABILIZATION PILOT STUDY, UNITED CHROME NPL SITE PILOT STUDY AND HEALTH AND SAFETY PROGRAM, UNITED CHROME NPL SITE PILOT STUDY

Science.gov (United States)

This document is a project plan for a pilot study at the United Chrome NPL site, Corvallis, Oregon and includes the health and safety and quality assurance/quality control plans. The plan reports results of a bench-scale study of the treatment process as iieasured by the ...

Photo Inactivation of Streptococcus mutans Biofilm by Violet-Blue light.

Science.gov (United States)

Gomez, Grace F; Huang, Ruijie; MacPherson, Meoghan; Ferreira Zandona, Andrea G; Gregory, Richard L

2016-09-01

Among various preventive approaches, non-invasive phototherapy/photodynamic therapy is one of the methods used to control oral biofilm. Studies indicate that light at specific wavelengths has a potent antibacterial effect. The objective of this study was to determine the effectiveness of violet-blue light at 380-440 nm to inhibit biofilm formation of Streptococcus mutans or kill S. mutans. S. mutans UA159 biofilm cells were grown for 12-16 h in 96-well flat-bottom microtiter plates using tryptic soy broth (TSB) or TSB with 1 % sucrose (TSBS). Biofilm was irradiated with violet-blue light for 5 min. After exposure, plates were re-incubated at 37 °C for either 2 or 6 h to allow the bacteria to recover. A crystal violet biofilm assay was used to determine relative densities of the biofilm cells grown in TSB, but not in TSBS, exposed to violet-blue light. The results indicated a statistically significant (P mutans growth and reduce the formation of S. mutans biofilm. This in vitro study demonstrated that violet-blue light has the capacity to inhibit S. mutans biofilm formation. Potential clinical applications of light therapy in the future remain bright in preventing the development and progression of dental caries.

Primary DNA damage in chrome-plating workers.

Science.gov (United States)

Gambelunghe, A; Piccinini, R; Ambrogi, M; Villarini, M; Moretti, M; Marchetti, C; Abbritti, G; Muzi, G

2003-06-30

In order to evaluate the primary DNA damage due to occupational exposure to chromium (VI), DNA strand-breaks and apoptosis in peripheral lymphocytes were measured in a group of 19 chrome-plating workers. DNA strand-breaks was assessed by alkaline (pH>13) single-cell microgel electrophoresis ('comet') assay, while apoptosis was measured by flow-cytometry after propidium iodide staining of the cells. Concentrations of chromium in urine, erythrocytes and lymphocytes were investigated as biological indicators of exposure. A group of 18 hospital workers (control group I) and another 20 university personnel (control group II) without exposure to chromium were also studied as controls. The results of the study show that chrome-plating workers have higher levels of chromium in urine, erythrocytes and lymphocytes than unexposed workers. Comet tail moment values, assumed as index of DNA damage, are increased in chromium-exposed workers and results are significantly correlated to chromium lymphocyte concentrations. No difference emerged in the percentage of apoptotic nuclei in exposed and unexposed workers. The study confirms that measurements of chromium in erythrocytes and lymphocytes may provide useful information about recent and past exposure to hexavalent chromium at the workplace. The increase in DNA strand-breaks measured by comet assay suggests this test is valid for the biological monitoring of workers exposed to genotoxic compounds such as chromium (VI).

NASA and ESA Collaboration on Hexavalent Chrome Alternatives: Pretreatments Only Final Test Report

Science.gov (United States)

Kessel, Kurt R.

2015-01-01

Hexavalent chromium (hex chrome or CR(VI)) is a widely used element within applied coating systems because of its self-healing and corrosion-resistant properties. The replacement of hex chrome in the processing of aluminum for aviation and aerospace applications remains a goal of great significance. Aluminum is the major manufacturing material of structures and components in the space flight arena. The National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA) are engaged in a collaborative effort to test and evaluate alternatives to hexavalent chromium containing corrosion coating systems. NASA and ESA share common risks related to material obsolescence associated with hexavalent chromium used in corrosion-resistant coatings.

The Role of Diffusion Media in Nitriding Process on Surface Layers Characteristics of AISI 4140 with and without Hard Chrome Coatings

Directory of Open Access Journals (Sweden)

K.A. Widi

2016-09-01

Full Text Available The surface layer characteristics of the AISI 4140 tool steel treated by nitriding gas before and after hard chrome plating utilizing pure nitrogen diffusion media (fluidized bed reactor and the without gas (muffle reactor has been studied experimentally. The result shows that nitriding substrate with hard chrome layers has nitrogen atoms concentration almost twice greater than that without hard chrome layers. After being given a hard chrome plating, nitriding on AISI 4140 steel generally has a nitrogen concentration of up to 4 times more than the substrate without hard chrome coating. Almost the entire specimen showed the highest concentration of N atoms in the area below the surface (hardening depth of 200 to 450 µm. N atoms diffusion depth profile has a correlation with hardening depth profile, especially on the specimens layered with hard chromium. The substrate without hard chrome plating tends to have higher surface hardness than the sub-surface. The results show that the effectiveness and efficiency of the gas nitriding diffusion process can be produced without the use of gas in the muffle reactor but the specimens must be hard chromium coated first. This phenomenon can be explained by the role of the passive layer formation that works as a barrier to keeps the spreading of N atoms concentrated in sub-surface areas.

Soybean plant growth study conducted using purified protein hydrolysate-based fertilizer made from chrome-tanned leather waste.

Science.gov (United States)

Pati, Anupama; Chaudhary, Rubina

2015-12-01

Leather processing discharges enormous amount of chrome containing leather solid waste which creates a major disposal problem. Chrome-tanned leather solid waste is a complex of collagen and chromium. The presence of chromium limits protein application in fertilizer industry. The purified protein hydrolysate with zero chromium could be used as a nitrogen source for fertilizer formulation. In this study, an attempt has been made to employ purified protein hydrolysate derived from chrome-tanned leather shavings (CTLS) in formulation of fertilizer. The formulated fertilizer (1–3 t ha(-1)) is employed as nitrogen source in production of soybean. Plant growth study demonstrates that formulated fertilizer dosage 3 t ha(-1) produced similar effects of commercial fertilizer-treated plants. Application of formulated fertilizer yielded higher seed in plant than commercial fertilizer.

Mid-term survivorship and clinical outcomes of cobalt-chrome and oxidized zirconium on highly crosslinked polyethylene.

Science.gov (United States)

Petis, Stephen M; Vasarhelyi, Edward M; Lanting, Brent A; Howard, James L; Naudie, Douglas D R; Somerville, Lyndsay E; McCalden, Richard W

2016-02-01

The choice of bearing articulation for total hip arthroplasty in younger patients is amenable to debate. We compared mid-term patient-reported outcomes and survivorship across 2 different bearing articulations in a young patient cohort. We reviewed patients with cobalt-chrome or oxidized zirconium on highly crosslinked polyethylene who were followed prospectively between 2004 and 2012. Kaplan-Meier analysis was used to determine predicted cumulative survivorship at 5 years with all-cause and aseptic revisions as the outcome. We compared patient-reported outcomes, including the Harris hip score (HHS), Western Ontario and McMaster University Osteoarthritis Index (WOMAC) and Short-form 12 (SF-12) scores. A total of 622 patients were followed during the study period. Mean follow-up was 8.2 (range 2.0-10.6) years for cobalt-chrome and 7.8 (range 2.1-10.7) years for oxidized zirconium. Mean age was 54.9 ± 10.6 years for cobalt-chrome and 54.8 ± 10.7 years for oxidized zirconium. Implant survivorship was 96.0% (95% confidence interval [CI] 94.9%-97.1%) for cobalt-chrome and 98.7% (95% CI 98.0%-99.4%) for oxidized zirconium on highly crosslinked polyethylene for all-cause revisions, and 97.2% (95% CI 96.2%-98.2%) for cobalt-chrome and 99.0% (95% CI 98.4%-99.6%) for oxidized zirconium for aseptic revisions. An age-, sex- and diagnosis-matched comparison of the HHS, WOMAC and SF-12 scores demonstrated no significant changes in clinical outcomes across the groups. Both bearing surface couples demonstrated excellent mid-term survivorship and outcomes in young patient cohorts. Future analyses on wear and costs are warranted to elicit differences between the groups at long-term follow-up.

Selection of the Chrome Reduction Bacteria in the Waste of Tanning Leather Industries by Ozonization Method

International Nuclear Information System (INIS)

Yazid, M.; Aris Bastianudin; Widdi Usada

2007-01-01

Selection of the chrome reduction bacteria in the waste of tanning leather industries by ozonization method has been done. The objectives of this research was to obtain isolate bacteria from the waste with chrome contain, so that expected can be used for chrome bioremediation agent for arrange to improved the waste treatment for tanning leather industries. Selection of bacteria in the waste was carried out by ozonization method with time variation 0 to 210 minutes by time interval 15 minutes. Isolation bacteria was carried out was grown on the BHI media for 24 hours at 37°C temperature. So be inoculated by streak plate method on the TBX, MC, EA, CTM and BP media. Characterization of bacteria was done by saw the colonies morphology, sel morphology and biochemical characterization. So, identification of isolate bacteria by matching profile method. The result of this research can be obtained 5 isolate bacteria BCR1, BCR2, BCR3, BCR4 and BCR5 with the different phenotypic character. From the five isolate can be selected resistance ozon isolate until 180 minutes time ozonization were BCR 2, were identified belong to the genus of Bacillus. The examination results showed that the isolate bacteria be able to reduction of the chrome concentration in the waste of tanning leather industries by 71.03 %. Efficiency. (author)

Effect of current imbalance on stability of a cable-in-conduit conductor consisting of chrome-plated strands

International Nuclear Information System (INIS)

Koizumi, Norikiyo; Takahashi, Yoshikazu; Nishi, Masataka; Isono, Takaaki; Tsuji, Hiroshi; Ono, Michitaka; Hamajima, Takataro; Fujioka, Tsutomu.

1997-02-01

The effect of an unbalanced current distribution in a conductor consisting of chrome plated strands on stability was investigated using a cable-in-conduit conductor (CICC) consisting of 27 NbTi chrome-plated strands. In addition, the quench behavior when a non-uniform current distribution was produced in the conductor was studied from the experimental results. Moreover, impedance of the chrome-plated strands was measured using the sample conductor. The results show that the stability is determined by the largest strand current when it is sufficiently large otherwise by the transport current when it is not high enough. It was found that it took a long time to make the conductor quench from the onset of the normal transition of the strand carrying the large current. This is explained by the good diffusivity of the coolant temperature in the conductor's cross section. Since the ramp-rate limitation cannot probably take place if the coolant temperature is diffused well in the conductor's cross section, it is expected the ramp-rate limitation can be prevented using this effect. It is also shown that the chrome-plated strands come into contact with one another with uniform transverse conductance on the order of 10 3 S/m. (author)

21 CFR 73.2775 - Manganese violet.

Science.gov (United States)

2010-04-01

.... Mercury (as Hg), not more than 1 part per million. Total color, based on Mn content in “as is” sample, not less than 93 percent. (c) Uses and restrictions. Manganese violet is safe for use in coloring cosmetics...

Radiolytic effects on Simpson Violet dye and their applications

International Nuclear Information System (INIS)

El-Banna, M.; Barakat, M.F.

2005-01-01

Simpson Violet dye has been exposed to γ-irradiation in non-aqueous solvents, and the color bleaching by irradiation was studied. The color bleaching was related to the applied dose. In another series of experiments, Simpson Violet dye was incorporated in polymethylmethacrylate films for studying the dose-response relationship. Finally, the results were compared with those obtained for externally dyed polymeric films. Most of the systems investigated were found suitable for gamma dose evaluation within a certain dose range. (author)

Chromatographic characterization of products isolated from chrome shavings

Directory of Open Access Journals (Sweden)

Edivaldo E Garcia

1999-01-01

Full Text Available Gel permeation chromatography and high performance liquid chromatography were employed for separation and chemical characterization of products isolated from chrome shavings. After enzymatic hydrolysis, the products isolated were peptides of higher molecular weight. Peptides of lower molecular weight and free aminoacids were the main products using sulfuric acid in chrome shavings solubilization. Glycine (17% , glutamic acid (10.6% , alanine (9.2% , and arginine (8.2% were the principal amino acids found. Phenylalanine(1.8% was the main aromatic amino acid , while tryptophane was completely absent.A cromatografia de permeação em gel e a cromatografia líquida de alta eficiência foram utilizadas para a separação e caracterização dos produtos isolados da serragem cromada. Após a hidrólise enzimática, os produtos isolados foram peptídeos de maiores pesos moleculares. Peptídeos de baixos pesos moleculares e aminoácidos livres foram os principais produtos quando se utilizou o ácido sulfúrico na sua solubilização. Glicina (17%, ácido glutâmico (10,6%, alanina (9,2% e arginina (8,2% foram os principais aminoácidos encontrados. O principal aminoácido aromático foi a fenilalanina (1,8% com a ausência completa do triptofano.

Microstructure and properties of high chrome steel roller after laser surface melting

International Nuclear Information System (INIS)

Li Meiyan; Wang Yong; Han Bin; Zhao Weimin; Han Tao

2009-01-01

Laser surface melting of high chrome steels was achieved by a 5 kW continuous wave CO 2 laser. The microstructure of the laser surface-melted steels was investigated by scanning electron microscopy, transmission electron microscopy and X-ray diffractometry, and the hardness profiles were determined by a Vickers hardness tester. The corrosion behavior in 3.5% NaCl solution was studied by electrochemical corrosion equipment. The large carbides of high chrome steels are completely dissolved and ultrafine dendrites of austenite with submicroscopic M 23 C 6 carbides precipitation are formed in the melted zone. The austenite in the melted zone has a high tempering stability. The corrosion resistance of the laser surface-melted steels is significantly improved due to the dissolution of carbides and the increase of the alloying elements in the solid solution as well as the large amount of austenite.

Characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA

International Nuclear Information System (INIS)

Zhou Dezhong; Deng Yongzhen; Li Ying

1986-01-01

The characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA is presented. Using the method of radiation-induced graft of BA instead of the chrome-retanning, the leather has been obviously improved not only in the surface, such as the brightness, fullness, uniformity of the thickness but also in the physical characteristics such as retaining of tensile strength, decreasing of water absorption after being immersed in water for 2h, and 24h, enhancement of tearing strength and stitch tear strength. Although the air permeability and water vapor permeability are a bit worse than the control, however is still in the range of the standard issued by Light Industry Ministry of China

Sonochemical Degradation Kinetics of Methyl Violet in Aqueous Solutions

Directory of Open Access Journals (Sweden)

Wei Lin Guo

2003-01-01

Full Text Available The sonochemical degradation in aqueous solution of methyl violet, chosen as a model of a basic dye, was studied. The ultrasonic degradation kinetics in water were found to be first-order and the degradation rate coefficient is 1.35×10-2 min-1 (R= 0.9934, n=8 at 20±1°C. The influence of the initial concentrations, reaction temperature and the pH of medium on the ultrasonic decomposition of methyl violet were also investigated.

Microstructure and properties of high chrome steel roller after laser surface melting

Energy Technology Data Exchange (ETDEWEB)

Li Meiyan, E-mail: lmy_102411@163.com [College of Electromechanical Engineering, China University of Petroleum, 271 Bei' er Road, Dongying 257061 (China); Wang Yong; Han Bin; Zhao Weimin; Han Tao [College of Electromechanical Engineering, China University of Petroleum, 271 Bei' er Road, Dongying 257061 (China)

2009-06-15

Laser surface melting of high chrome steels was achieved by a 5 kW continuous wave CO{sub 2} laser. The microstructure of the laser surface-melted steels was investigated by scanning electron microscopy, transmission electron microscopy and X-ray diffractometry, and the hardness profiles were determined by a Vickers hardness tester. The corrosion behavior in 3.5% NaCl solution was studied by electrochemical corrosion equipment. The large carbides of high chrome steels are completely dissolved and ultrafine dendrites of austenite with submicroscopic M{sub 23}C{sub 6} carbides precipitation are formed in the melted zone. The austenite in the melted zone has a high tempering stability. The corrosion resistance of the laser surface-melted steels is significantly improved due to the dissolution of carbides and the increase of the alloying elements in the solid solution as well as the large amount of austenite.

RESEARCH OF PROCESS OF AN ALLOYING OF THE FUSED COATINGS RECEIVED FROM THE SUPERFICIAL ALLOYED WIRE BY BORON WITH IN ADDITIONALLY APPLIED ELECTROPLATED COATING OF CHROME AND COPPER

Directory of Open Access Journals (Sweden)

V. A. Stefanovich

2015-01-01

Full Text Available Researches on distribution of chrome and copper in the fused coating received from the superficial alloyed wire by boron with in additionally applied electroplated coating of chrome and copper were executed. The structure of the fused coating consists of dendrites on which borders the boride eutectic is located. It is established that the content of chrome in dendrites is 1,5– 1,6 times less than in the borid; distribution of copper on structure is uniformed. Coefficients of digestion of chrome and copper at an argon-arc welding from a wire electrode with electroplated coating are established. The assimilation coefficient for chrome is equal to 0,9–1,0; for copper – 0,6–0,75.

Oxidation kinetics of crystal violet by potassium permanganate in acidic medium

Science.gov (United States)

Khan, Sameera Razi; Ashfaq, Maria; Mubashir; Masood, Summyia

2016-05-01

The oxidation kinetics of crystal violet (a triphenylmethane dye) by potassium permanganate was focused in an acidic medium by the spectrophotometric method at 584 nm. The oxidation reaction of crystal violet by potassium permanganate is carried out in an acidic medium at different temperatures ranging within 298-318 K. The kinetic study was carried out to investigate the effect of the concentration, ionic strength and temperature. The reaction followed first order kinetics with respect to potassium permanganate and crystal violet and the overall rate of the reaction was found to be second order. Thermodynamic activation parameters like the activation energy ( E a), enthalpy change (Δ H*), free energy change (Δ G*), and entropy change (Δ S*) have also been evaluated.

Decolorization of Malachite Green and Crystal Violet by Waterborne Pathogenic Mycobacteria

OpenAIRE

Jones, Jefferson J.; Falkinham III, Joseph O.

2003-01-01

Mycobacterium avium, Mycobacterium intracellulare, Mycobacterium scrofulaceum, Mycobacterium marinum, and Mycobacterium chelonae tolerate high concentrations of the dyes malachite green and crystal violet. Cells of strains of those species decolorized (reduced) both malachite green and crystal violet. Because decolorized malachite green lacked antimicrobial activity, the resistance of these mycobacteria could be due, in part, to their ability to decolorize the dyes. Small amounts of malachite...

Waste Treatment of Chrome Residue of Chromium Recovery Process Using Calcium Carbonate

International Nuclear Information System (INIS)

Endro Kismolo; Prayitno; Nurimaniwathy

2002-01-01

The aim of the research was to apply the precipitation technology for the treatment of aqueous wastes of leather tanning industries. The chrome liquid wastes taken was the effluent from the residue of the chromium recovery process using magnesium oxide. The precipitant used was calcium carbonate. The experiments was performed by adjusting the concentration of calcium carbonate from 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm, 300 ppm, 350 ppm to 400 ppm. The stirring speed was varied from 50 rpm, 75 rpm, 100 rpm, 125 rpm, 150 rpm, 175 rpm to 200 rpm. The time of mixing was varied from 30 minutes, 60 minutes, 90 minutes, 120 minutes, 150 minutes, 175 minutes and 200 minutes. The result from the experiments lead to the best condition obtained were the concentration of precipitant was 300 ppm, flow rates of mixing was 125 rpm and time of mixing was 60 minutes. At this condition the separations efficiency of chrome obtained was 99.985%. (author)

Magnetic solid-phase extraction for determination of the total malachite green, gentian violet and leucomalachite green, leucogentian violet in aquaculture water by high-performance liquid chromatography with fluorescence detection.

Science.gov (United States)

Zhao, Jiao; Wei, Daqiao; Yang, Yaling

2016-06-01

In this study, magnetic multi-walled carbon nanotube nanoparticles were synthesized and used as the adsorbent for the sums of malachite green, gentian violet and leucomalachite green, leucogentian violet in aquaculture water samples followed by high performance liquid chromatography with fluorescence detection. This method was based on in situ reduction of chromic malachite green, gentian violet to colorless leucomalachite green, leucogentian violet with potassium borohydride, respectively. The obtained adsorbent combines the advantages of carbon nanotubes and Fe3 O4 nanoparticles in one material for separation and preconcentration of the reductive dyes in aqueous media. The structure and properties of the prepared nanoparticles were characterized by transmission and scanning electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy. The main parameters affecting the adsorption recoveries were investigated and optimized, including reducing agent concentration, type and amount of sorbent, sample pH, and eluting conditions. Under the optimum conditions, the limits of detection in this method were 0.22 and 0.09 ng/mL for malachite green and gentian violet, respectively. Product recoveries ranged from 87.0 to 92.8% with relative standard deviations from 4.6 to 5.9%. The results indicate that the sorbent is a suitable material for the removal and concentration of triphenylmethane dyes from polluted environmental samples. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Violet-blue photoluminescence from Si nanoparticles with zinc-blende structure synthesized by laser ablation in liquids

Directory of Open Access Journals (Sweden)

P. Liu

2013-02-01

Full Text Available Violet-blue luminescence from Si nanostructures has been widely investigated, because of its potential use in optoelectronic and bioimaging devices. However, the emission mechanism in multiform Si nanomaterials remains unclear. In this contribution, Si nanocrystals (NCs with zincblende structure and visible violet-blue emission are prepared by electric field assisted laser ablation in liquids. While subsequent annealing of the Si NCs weakens their blue emission dramatically. We investigate the origin of the violet-blue emission by monitoring crystal structure transitions and photoluminescence during different treatments of the Si NCs. The results indicate that the violet-blue emission cannot simply be ascribed to quantum confinement effects or the presence of general surface states on the Si NCs. Instead, we propose that excitons are formed within the Si NCs by direct transitions at Γ or X points, which can be induced during the formation of the zincblende structure, and are a most possible origin of the violet-blue luminescence. Furthermore, defects in the metastable Si NCs are also expected to play an important role in violet-blue emission. This study not only gives clear and general insight into the physical origins of violet-blue emission from Si NCs, it also provides useful information for designing optoelectronic devices based on Si NCs.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids.

Science.gov (United States)

Krishnamoorthy, G; Sadulla, S; Sehgal, P K; Mandal, Asit Baran

2012-05-15

In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T(s)) and denaturation temperature (T(d)) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T(s) of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning. Copyright © 2012 Elsevier B.V. All rights reserved.

Do birds in flight respond to (ultra)violet lighting?

Institute of Scientific and Technical Information of China (English)

Roel May; Jens Åström; Øyvind Hamre; Espen Lie Dahl

2017-01-01

Background: Concerns for bird collisions with wind turbines affect the deployment of onshore and offshore wind-power plants. To avoid delays in consenting processes and to streamline the construction and operation phase, func-tional mitigation measures are required which efficiently reduces bird mortality. Vision is the primary sensory system in birds, which for a number of species also includes the ultraviolet spectrum. Many bird species that are known to collide with offshore wind turbines are sensitive in the violet or ultraviolet spectrum. For species that are mainly active at lower ambient light levels, lighting may deter birds from the lit area. Utilizing (ultra)violet lights may in addition not disturb humans. However, we do not know whether UV-sensitive birds in flight actually respond behaviourally to UV lights. Methods: We therefore tested the efficacy of two types of lights within the violet (400 nm) and ultraviolet (365 nm) spectrum to deter birds from the lit area. These lights were placed vertically and monitored continuously between dusk and dawn using an avian radar system. Results: Relative to control nights, bird flight activity (abundance) was 27% lower when the ultraviolet light was on. Violet light resulted in a 12% decrease in overall abundance, and in addition, a vertical displacement was seen, increasing the average flight altitude by 7 m. Although temporal changes occurred, this effect persisted over the season below 40 m above sea level. Conclusions: Although the results from this pilot study are promising, we argue there still is a long way to go before a potentially functional design to mitigate collisions that has proven to be effective in situ may be in place.

PEEK-OPTIMA? as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study

OpenAIRE

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-01-01

PEEK-OPTIMA™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA™ femoral components art...

Effects of nanodiamonds of explosive synthesis on the skin of experimental animals locally exposed to cobalt and chrome ions.

Science.gov (United States)

Prokhorenkov, V I; Vasil'eva, E Yu; Puzyr', A P; Bondar', V S

2014-12-01

Experiments in vivo demonstrated the protective effect of modified nanodiamonds on guinea pig skin after local exposure cobalt ions, but not chrome ions. The observed differences are determined by different adsorption of these ions by nanodiamonds: in vitro experiments showed that nanodiamonds adsorbed cobalt ions, but not chrome ions from water solutions. The perspectives of using modified nanodiamonds as a new adsorbent for prevention of allergic contact dermatitis induced by ions of bivalent metals are discussed.

[Biosorption of crystal violet and malachite green by Rhodotorula graminis Y-5].

Science.gov (United States)

Hu, Rong; Huang, Jian-Bo; Yang, Zhou-Ping; Cheng, Zi-Zhang; Jing, De-Jun; Huang, Qian-Ming

2011-12-01

With a shaker, this paper studied the characteristics of the biosorption of crystal violet and malachite green by Rhodotorula graminis Y-5 under different adsorption time, initial pH, and temperature, as well as the desorption and recycling use of the dyes. The biosorption of crystal violet and malachite green by R. graminis Y-5 had the peaks (93.8% and 87.7%, respectively) at pH 7.0, dye concentration 50 mg x L(-1), 150 r x min(-1), 30 degrees C, and lasting 10 hours. After desorption, the biosorption rate of crystal violet and malachite green by R. graminis was 85.5% and 78.5%, respectively, indicating that the biosorption of crystal violet and malachite green was reversible, and the recycling use of the dyes by R. graminis was quite good, i. e., the dyes were renewable and could be recycled. Biosorption could be the mechanism of the decolorization of the dyes. The dyes were mostly adsorbed on the R. graminis surface -OH. The adsorption process was fast, efficient, and reversible, suggesting that R. graminis had a high potential for waste water treatment.

Minimization of the environmental impact of chrome tanning: a new process with high chrome exhaustion.

Science.gov (United States)

Morera, Josep M; Bacardit, Anna; Ollé, Lluís; Bartolí, Esther; Borràs, Maria D

2007-11-01

In all tanning technology operations wastes are generated. These reach the environment as residual waters, solid and liquid waste as well as atmospheric emissions and odours. This study tests an alternative method to the traditional tanning method at an industrial level. The new method is based on tanning without float and by significantly increasing the temperature at the end of the tanning process. The properties of the leathers obtained using the two methods have been compared and the results indicate that those leathers have similar physical, chemical, and organoleptic properties. However, the differences existing from the environmental point of view are significant. It is not necessary to use clean water for this tanning. Moreover, there is a 75% reduction of the residual float, a 91% reduction of the chrome discharged, and a 94% reduction of the chlorides discharged. A financial assessment was carried out to demonstrate that the newly proposed system is 32% more economic than the traditional one.

Radiation-initiated graft polymerization of methyl acrylate onto chrome-tanned sheepskin

International Nuclear Information System (INIS)

Kaldirimci, C.; Bas, N.

1982-01-01

Radiation grafting method was applied to obtain leather-polymer composite. Grafting of methyl acrylate onto chrome-tanned, bluestock sheepskin was investigated under the initiatory effect of 60 Co radiation of 0.20 11.50 Mrad. The percent of grafting was determined and water adsorption and shrinkage temperature measurements were carried out. It was shown that 2-4 Mrad is convenient to produce leather-polymer composite. (author)

Application of Nuclear methods in the chrome bed prospecting from Casimba sector, Pinares de Mayari

International Nuclear Information System (INIS)

Guerra, M.; Velazquez Cruz, R.

1993-01-01

A study for chrome determination in Casimba sector, Pinares de Mayari, was carried out using nuclear geophysical methods: and spectrometry neutron-gamma capture. For this purpose Cs 137 and Am-Be sources were used

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... cattle-like hides into finished leather by hair save unhairing, chrome tanning, and retan-wet finishing. ...

Biosorption of aniline violet from aqueous solution on moringa oleifera saw dust (abstract)

International Nuclear Information System (INIS)

Javed, T.; Mirza, M.L.

2011-01-01

Batch adsorption studies were carried out to evaluate the potential of Moringa Oleifera wood saw dust for the removal of aniline violet dye from aqueous solution by optimizing different parameters such as effect of shaking time, adsorbent dose, initial adsorbate concentration etc. The experimental data was subjected to different types of linearized isotherm models such as Freundlich, Langmuir and Dubinin-Radushkevich. The Freundlich isotherm was fitted well with the data. The maximum adsorption capacity of 8.92 m mol./g of aniline violet has been observed through Freundlich isotherm by using the optimized parameters of 50 mg of adsorbent, 5 minutes of shaking time at room temperature of 25 deg. C. The sorption mean free energy from Dubinin-Radushkevich isotherm is 13.36 kJ mol 1 indicating chemisorption. Pseudo-first and Pseudo-second order kinetics models were tested for the adsorption of 1.23 X 10/sup -5) mol L/sup -1) of aniline violet onto Moringa Oleifera wood saw dust. The experimental data fitted well for Pseudo-second order model with coefficient of correlation R/sup 2/ greater or equal to 0.999. The uptake of aniline violet was also studied with the rise in temperature. Thermodynamic parameters have been evaluated and the adsorption process seems to be endothermic. The results indicate that the Moringa Oleifera wood saw dust is an efficient adsorbent for aniline violet from aqueous solutions. (author)

Photochemical reaction monitoring by ultra-violet spectrophotometry.

Science.gov (United States)

Roig, B; Touraud, E; Thomas, O

2002-11-01

Within the framework of the monitoring of the trichloroacetylchloride (TCAC) photosynthesis, ultra-violet (UV) spectrophotometry is proposed as a simple and rapid tool allowing, in real time, the control of the process efficiency. A good correlation has been obtained between the results acquired by this alternative method and the standard gas chromatography.

Behavioural ecology of the Namibian Violet Woodhoopoe ...

African Journals Online (AJOL)

We studied the behavioural ecology of the Violet Woodhoopoe Phoeniculus damarensis, a rare species endemic to Namibia and southern Angola. Groups in Namibia consisted on average of 4.3 ± 1.6 individuals, with apparently only a single breeding pair. Non-breeding group members of both sexes brought food to the ...

Effect of Violet-Blue Light on Streptococcus mutans-Induced Enamel Demineralization

Directory of Open Access Journals (Sweden)

Grace Gomez Felix Gomez

2018-03-01

Full Text Available Background: This in vitro study determined the effectiveness of violet-blue light (405 nm on inhibiting Streptococcus mutans-induced enamel demineralization. Materials and Methods: S. mutans UA159 biofilm was grown on human enamel specimens for 13 h in 5% CO2 at 37 °C with/without 1% sucrose. Wet biofilm was treated twice daily with violet-blue light for five minutes over five days. A six-hour reincubation was included daily between treatments excluding the final day. Biofilms were harvested and colony forming units (CFU were quantitated. Lesion depth (L and mineral loss (∆Z were quantified using transverse microradiography (TMR. Quantitative light-induced fluorescence Biluminator (QLF-D was used to determine mean fluorescence loss. Data were analyzed using one-way analysis of variance (ANOVA to compare differences in means. Results: The results demonstrated a significant reduction in CFUs between treated and non-treated groups grown with/without 1% sucrose. ∆Z was significantly reduced for specimens exposed to biofilms grown without sucrose with violet-blue light. There was only a trend on reduction of ∆Z with sucrose and with L on both groups. There were no differences in fluorescence-derived parameters between the groups. Conclusions: Within the limitations of the study, the results indicate that violet-blue light can serve as an adjunct prophylactic treatment for reducing S. mutans biofilm formation and enamel mineral loss.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

International Nuclear Information System (INIS)

Tariq, Saadia R.; Shah, Munir H.; Shaheen, Nazia

2009-01-01

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil.

Science.gov (United States)

Tariq, Saadia R; Shah, Munir H; Shaheen, Nazia

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

Energy Technology Data Exchange (ETDEWEB)

Tariq, Saadia R. [Department of Chemistry, Lahore College for Women University, Lahore (Pakistan); Shah, Munir H., E-mail: munir_qau@yahoo.com [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Shaheen, Nazia [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan)

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

International Nuclear Information System (INIS)

Pietrucha, K.; Pekala, W.; Kroh, J.

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with 60 Co γ-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed. (author)

Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

Energy Technology Data Exchange (ETDEWEB)

Pietrucha, K.; Pekala, W.; Kroh, J. (Lodz Univ. (Poland))

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with /sup 60/Co ..gamma..-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed.

Surface enrichment with chrome and nitriding of IF steel under an abnormal glow discharge

International Nuclear Information System (INIS)

Meira, S.R.; Borges, P.C.; Bernardelli, E.A.

2014-01-01

The objective of this work is to evaluate the influence of surface enrichment of IF steel with chrome, and nitriding, the formation of the nitrided layer. Thus, IF steel samples were subjected to surface enrichment process, using 409 stainless steel as a target for sputtering, followed by plasma nitriding, both under a dc abnormal glow discharge. The enrichment treatment was operated at 1200 ° C for 3h. The nitriding treatment was operated at 510 ° C for 2 h. The influence of the treatments on the layers formed was studied through optical microscopy (OM), scan electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microindentation. The results show that the enrichment is effective to enrich the IF surface, furthermore, improves the characteristics of nitriding, comparing nitriding samples to nitriding and enriched, was observed needles of nitrides, as well as a higher hardness, which is associated with the nitrides of chrome, on the nitriding and enriched samples. (author)

Nucleotide sequence of Hungarian grapevine chrome mosaic nepovirus RNA1.

OpenAIRE

Le Gall, O; Candresse, T; Brault, V; Dunez, J

1989-01-01

The nucleotide sequence of the RNA1 of hungarian grapevine chrome mosaic virus, a nepovirus very closely related to tomato black ring virus, has been determined from cDNA clones. It is 7212 nucleotides in length excluding the 3' terminal poly(A) tail and contains a large open reading frame extending from nucleotides 216 to 6971. The presumably encoded polyprotein is 2252 amino acids in length with a molecular weight of 250 kDa. The primary structure of the polyprotein was compared with that o...

75 FR 52930 - Carbazole Violet Pigment 23 From India: Preliminary Results of Antidumping Duty Changed...

Science.gov (United States)

2010-08-30

... of presscake and dry color. Pigment dispersions in any form (e.g., pigment dispersed in oleoresins... DEPARTMENT OF COMMERCE International Trade Administration [A-533-838] Carbazole Violet Pigment 23... order on carbazole violet pigment 23 from India to determine whether Meghmani Pigments (Meghmani) is the...

Separation of motor oils, oily wastes and hydrocarbons from contaminated water by sorption on chrome shavings.

Science.gov (United States)

Gammoun, A; Tahiri, S; Albizane, A; Azzi, M; Moros, J; Garrigues, S; de la Guardia, M

2007-06-25

In this paper, the ability of chrome shavings to remove motor oils, oily wastes and hydrocarbons from water has been studied. To determine amount of hydrocarbons sorbed on tanned wastes, a FT-NIR methodology was used and a multivariate calibration based on partial least squares (PLS) was employed for data treatment. The light density, porous tanned waste granules float on the surface of water and remove hydrocarbons and oil films. Wastes fibers from tannery industry have high sorption capacity. These tanned solid wastes are capable of absorbing many times their weight in oil or hydrocarbons (6.5-7.6g of oil and 6.3g of hydrocarbons per gram of chrome shavings). The removal efficiency of the pollutants from water is complete. The sorption of pollutants is a quasi-instantaneous process.

CHROME: An Approach to Teaching the Concept of Inter-Functional Cooperation in Services Organizations

Science.gov (United States)

Johnson, Lester W.

2010-01-01

When teaching a services course (e.g., Services Marketing) it is essential that students understand that marketing/management, operations and human resource management within the service organization be fully coordinated. One useful acronym used to remind students of this need is "CHROME", standing for Communications, Human Resources,…

Investigation of adsorption of the dyestuff astrazon red violet 3rn (basic violet 16 on montmorillonite clay

Directory of Open Access Journals (Sweden)

B. A. Fil

2014-03-01

Full Text Available In this study, color removal by absorption from synthetically prepared wastewater was investigated using montmorillonite clay by adsorption. As dyestuff Astrazon Red Violet 3RN (Basic Violet 16 was used. Experimental parameters selected were pH, temperature, agitation speed, initial dyestuff concentration, adsorbent dosage and ionic strength. It was established that adsorption rate increased with increasing pH, temperature, dye concentration and agitation speed, but decreased with increased ionic strength and adsorbent dosage. Adsorption equilibrium data obtained by a series of experiments carried out in a water bath were employed with common isotherm equations such as Langmuir, Freundlich, Temkin, Elovich and Dubinin-Radushkevich. It was found that the Langmuir equation appears to fit the equilibrium data better than the other models. Furthermore, the fit of the kinetic data to common kinetic models such as the pseudo-first-order, second-order, Elovich and intraparticle diffusion models was tested to elucidate the adsorption mechanism. Kinetic data conformed to the pseudo-second-order model, indicating chemisorptions. In addition, the thermodynamic parameters activation energy, Ea, enthalpy ΔH*, entropy, ΔS*, and free energy change, ΔG*, were calculated. The values of the calculated parameters indicated that physical adsorption of ARV on the clay was dominant and that the adsorption process was endothermic.

A useful single-solution polychrome stain for plant material...Brook Cyte-Chrome I.

Science.gov (United States)

Stanley L Krugman; Julia F. Littlefield

1968-01-01

Fresh and chemically fixed sectioned plant material can be quickly stained by applying a Brook Cyte Chrome I polychrome stain. Staining time averaged only about 10 minutes. And exact timing of staining and de-staining is not as critical as with most of the commonly used stains. The overall quality is comparable to that of the traditional stains.

Dynamics of InGaN tandem blue-violet semiconductor lasers

International Nuclear Information System (INIS)

Antohi, I.; Rusu, S.S.; Tronciu, V.Z.

2013-01-01

Full text: Blue-violet semiconductor lasers have received much attention because of their promise for high-density optical storage applications. In particular, blue-violet laser diodes operating at 400 nm are required for BD- systems and for use in medicine, biology, color printers and monitors, etc, In recent years, numerous fabrication methods have been proposed and developed for blue lasers with CW and self-pulsating operations and the lifetime of such lasers has been increased to over 15000 h. Recently, we have reported self-pulsation and excitable behaviour for an InGaN laser with a p-type saturable absorber, and SP in the frequency range from 1.6 to 2.9 GHz has been achieved with such lasers. In this paper, we present an investigation of the dynamics of tandem 400 nm blue-violet lasers with setup presented in Fig.1a. A particular feature of the devices is the connection of the contacts of the SA, to reduce the carrier lifetime in the SA with the intention of producing self-pulsation and excitability. We examine the laser dynamics in terms of bifurcation diagrams. A typical calculation of bifurcation for the periodic solution is shown in Fig. 1b. This figure shows the dependence of the peak of the photon number on the injected.

75 FR 977 - Carbazole Violet Pigment 23 From India: Preliminary Results of Countervailing Duty Administrative...

Science.gov (United States)

2010-01-07

... the form of presscake and dry color. Pigment dispersions in any form (e.g., pigments dispersed in... DEPARTMENT OF COMMERCE International Trade Administration [C-533-839] Carbazole Violet Pigment 23... countervailing duty order on carbazole violet pigment 23 (CVP-23) from India for the period January 1, 2007...

STUDIES ON BIOLUMINESCENCE : XVII. FLUORESCENCE AND INHIBITION OF LUMINESCENCE IN CTENOPHORES BY ULTRA-VIOLET LIGHT.

Science.gov (United States)

Harvey, E N

1925-01-20

1. Small dumps of the luminous cells of Mnemiopsis cannot readily be stimulated mechanically but will luminesce on treatment with saponin solution. Larger groups of luminous cells (such as are connected with two paddle plates) luminesce on mechanical stimulation. This suggests that mechanical stimulation to luminesce occurs chiefly through a nerve mechanism which has been broken up in the small dumps of luminous tissue. 2. The smallest bits of luminous tissue, even cells freed from the animal by agitation, that will pass through filter paper, lose their power to luminesce in daylight and regain it (at least partially) in the dark. 3. Luminescence of the whole animal and of individual cells is suppressed by near ultra-violet light (without visible light). 4. Inhibition in ultra-violet light is not due to stimulation (by the ultra-violet light) of the animal to luminesce, thereby using up the store of photogenic material. 5. Animals stimulated mechanically several times and placed in ultra-violet light show a luminescence along the meridians in the same positions as the luminescence that appears on stimulation. This luminescence in the ultra-violet or "tonic luminescence," is not obtained with light adapted ctenophores and is interpreted to be a fluorescence of the product of oxidation of the photogenic material. 6. Marked fluorescence of the luminous organ of the glowworm (Photuris) and of the luminous slime of Chatopterus may be observed in ultra-violet but no marked fluorescence of the luminous substances of Cypridina is apparent. 7. Evidence is accumulating to show a close relation between fluorescent and chemiluminescent substances in animals, similar to that described for unsaturated silicon compounds and the Grignard reagents.

Violet and visual flux problems in red giant stars

International Nuclear Information System (INIS)

Faulkner, D.R.

1989-01-01

Red giant stars are sites of many astrophysically interesting processes and are important links to late stages of stellar evolution and the chemical history of the galaxy. Much of what is known about stars comes from their spectra, which are formed in the outer layers (atmospheres). Unfortunately the low temperatures in red giant atmospheres promote the formation of many molecules, and the resultant complexity of the spectra has slowed progress in obtaining good models of these objects and leaves many unanswered questions. Several of these problems are investigated. Spectra of red giants provide a natural classification according to composition: M stars are oxygen rich, C stars are carbon rich, while S stars are intermediate. One long standing problem with C stars has been the explanation of the severe lack of energy flux in the violet and near ultraviolet part of their spectrum, generally attributed to an unusual opacity. Results show that one source, SiC, is untenable, while the case for the other, C3, is severely weakened. Synthetic spectra from atmospheric models are compared to spectra of TX Psc, a C star, to show that the contribution of thousands of atomic lines are probably responsible for the violet and ultraviolet flux deficiency. The agreement between the synthetic spectra and observations is very good. K and M type stars also have a violet flux deficiency, though it is less severe than with carbon stars

PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study.

Science.gov (United States)

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-11-01

PEEK-OPTIMA ™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA ™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA ™ femoral components articulating against all-polyethylene tibial components was carried out under two kinematic conditions: 3 million cycles under intermediate kinematics (maximum anterior-posterior displacement of 5 mm) followed by 3 million cycles under high kinematic conditions (anterior-posterior displacement 10 mm). The wear of the GUR1020 ultra-high-molecular-weight polyethylene tibial components was assessed by gravimetric analysis; for both material combinations under each kinematic condition, the mean wear rates were low, that is, below 5 mm 3 /million cycles. Specifically, under intermediate kinematic conditions, the wear rate of the ultra-high-molecular-weight polyethylene tibial components was 0.96 ± 2.26 mm 3 /million cycles and 2.44 ± 0.78 mm 3 /million cycle against cobalt chrome and PEEK-OPTIMA ™ implants, respectively (p = 0.06); under high kinematic conditions, the wear rates were 2.23 ± 1.85 mm 3 /million cycles and 4.44 ± 2.35 mm 3 /million cycles, respectively (p = 0.03). Following wear simulation, scratches were apparent on the surface of the PEEK-OPTIMA ™ femoral components. The surface topography of the femoral components was assessed using contacting profilometry and showed a statistically significant increase in measured surface roughness of the PEEK-OPTIMA ™ femoral components compared to the cobalt chrome implants. However, this did not appear to influence the wear rate, which remained linear over the duration of

PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of total knee replacement: A preliminary study

Science.gov (United States)

Cowie, Raelene M; Briscoe, Adam; Fisher, John; Jennings, Louise M

2016-01-01

PEEK-OPTIMA™ (Invibio Ltd, UK) has been considered as an alternative joint arthroplasty bearing material due to its favourable mechanical properties and the biocompatibility of its wear debris. In this study, the potential to use injection moulded PEEK-OPTIMA™ as an alternative to cobalt chrome in the femoral component of a total knee replacement was investigated in terms of its wear performance. Experimental wear simulation of three cobalt chrome and three PEEK-OPTIMA™ femoral components articulating against all-polyethylene tibial components was carried out under two kinematic conditions: 3 million cycles under intermediate kinematics (maximum anterior-posterior displacement of 5 mm) followed by 3 million cycles under high kinematic conditions (anterior-posterior displacement 10 mm). The wear of the GUR1020 ultra-high-molecular-weight polyethylene tibial components was assessed by gravimetric analysis; for both material combinations under each kinematic condition, the mean wear rates were low, that is, below 5 mm3/million cycles. Specifically, under intermediate kinematic conditions, the wear rate of the ultra-high-molecular-weight polyethylene tibial components was 0.96 ± 2.26 mm3/million cycles and 2.44 ± 0.78 mm3/million cycle against cobalt chrome and PEEK-OPTIMA™ implants, respectively (p = 0.06); under high kinematic conditions, the wear rates were 2.23 ± 1.85 mm3/million cycles and 4.44 ± 2.35 mm3/million cycles, respectively (p = 0.03). Following wear simulation, scratches were apparent on the surface of the PEEK-OPTIMA™ femoral components. The surface topography of the femoral components was assessed using contacting profilometry and showed a statistically significant increase in measured surface roughness of the PEEK-OPTIMA™ femoral components compared to the cobalt chrome implants. However, this did not appear to influence the wear rate, which remained linear over the duration of the study. These

Influences of the current density on the performances of the chrome-plated layer in deterministic electroplating repair

Science.gov (United States)

Xia, H.; Shen, X. M.; Yang, X. C.; Xiong, Y.; Jiang, G. L.

2018-01-01

Deterministic electroplating repair is a novel method for rapidly repairing the attrited parts. By the qualitative contrast and quantitative comparison, influences of the current density on performances of the chrome-plated layer were concluded in this study. The chrome-plated layers were fabricated under different current densities when the other parameters were kept constant. Hardnesses, thicknesses and components, surface morphologies and roughnesses, and wearability of the chrome-plated layers were detected by the Vickers hardness tester, scanning electron microscope / energy dispersive X-ray detector, digital microscope in the 3D imaging mode, and the ball-milling instrument with profilograph, respectively. In order to scientifically evaluate each factor, the experimental data was normalized. A comprehensive evaluation model was founded to quantitative analyse influence of the current density based on analytic hierarchy process method and the weighted evaluation method. The calculated comprehensive evaluation indexes corresponding to current density of 40A/dm2, 45A/dm2, 50A/dm2, 55A/dm2, 60A/dm2, and 65A/dm2 were 0.2246, 0.4850, 0.4799, 0.4922, 0.8672, and 0.1381, respectively. Experimental results indicate that final optimal option was 60A/dm2, and the priority orders were 60A/dm2, 55A/dm2, 45A/dm2, 50A/dm2, 40A/dm2, and 65A/dm2.

75 FR 10759 - Carbazole Violet Pigment 23 from India: Initiation of Antidumping Duty Changed-Circumstances Review

Science.gov (United States)

2010-03-09

... dispersions in any form (e.g., pigment dispersed in oleoresins, flammable solvents, water) are not included... DEPARTMENT OF COMMERCE International Trade Administration [A-533-838] Carbazole Violet Pigment 23... changed-circumstances review of the antidumping duty order on carbazole violet pigment 23 from India with...

Spectrophotometric determination of Sc in eriochrome cyanine R(chrome azurol S) - phosphatidyl choline system

International Nuclear Information System (INIS)

Xu, Y.; Chen, X.; Hu, Z.

1987-01-01

Eriochrome cyanine R(chrome azurol S) is used as a color reagent to determine Sc in the presence of phosphatidyl choline, eta = 3.7 * 10 4 (4.5 * 10 4 ). This method has been connected to extraction separation to determine Sc in the presence of rare earth elements, and good results have been obtained. Phosphatidyl choline(PC) is a biochemical reagent, which can be used as a surfactant. It has been reported that chrome azurol S(CAS) can be used to determine Be in the presence of PC but it has not been reported that eriochrome cyanine R(ECR) and CAS can been used to determine Sc in the presence of PC. This paper has put forward a method by which Sc can be determined. ECR (CAS) has been used as a color reagent and PC as a surfactant. Conditional experiments have been made and this method has been connected to extraction separation. Tributyl phosphate (TBP) extracts Sc from rare earth elements to make a determination and good results have been obtained

75 FR 33243 - Carbazole Violet Pigment 23 From India: Final Results of Countervailing Duty Administrative Review

Science.gov (United States)

2010-06-11

... powder, paste, wet cake) and finished pigment in the form of presscake and dry color. Pigment dispersions... DEPARTMENT OF COMMERCE International Trade Administration [C-533-839] Carbazole Violet Pigment 23... countervailing duty order on carbazole violet pigment 23 from India for the period January 1, 2007, through...

Quantitative chemical microdetermination of beryllium with chrome azurol by the ring-oven technique

International Nuclear Information System (INIS)

Hansen, N.B.

1982-01-01

A method for determination of beryllium in minerals and rocks is described. Because of the toxicity of beryllium the method is designed for determination of 1-10 ng of Be. The sample is fused with sodium carbonate and sodium tetraborate. Interfering metals are masked with EDTA. Be is determined by the Weisz ring-oven method with Chrome Azurol. The relative error is 10%. (Author)

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Science.gov (United States)

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING... addition to other unhairing and tanning operation, processes raw or cured cattle or cattle-like hides into finished leather by chemically dissolving the hide hair, chrome tanning, and retan-wet finishing. ...

75 FR 38076 - Carbazole Violet Pigment 23 from India: Final Results of Antidumping Duty Administrative Review

Science.gov (United States)

2010-07-01

... the form of presscake and dry color. Pigment dispersions in any form (e.g., pigment dispersed in... DEPARTMENT OF COMMERCE International Trade Administration [A-533-838] Carbazole Violet Pigment 23... carbazole violet pigment 23 (CVP 23) from India. The review covers exports of this merchandise to the United...

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

International Nuclear Information System (INIS)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K.; Mandal, Asit Baran

2012-01-01

Highlights: ► Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. ► Increased hydrothermal stability of collagen via intra and inter molecular crosslink. ► D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. ► D-AA in collagen creates new topologies inaccessible to homo chiral molecules. ► Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T s ) and denaturation temperature (T d ) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T s of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

Demonstration of lipofuscin and Nissl bodies in crystal violet stained sections using a fluorescence technique or pyronin Y stain.

Science.gov (United States)

Terr, L I

1986-09-01

This paper presents two simple, reliable methods for identification of lipofuscin and Nissl bodies in the same section. One method shows that lipofuscin stained with crystal violet retains its ability to fluoresce and can be observed under the fluorescence microscope after the stain has faded. Fading is accompanied by a gradual increase in the intensity of the fluorescence and is complete in about 5 min. Exciting illumination from this part of the spectrum also substantially fades staining of other autofluorescing tissue elements, such as lipids. Nonfluorescing structures, such as Nissl bodies, remain stained. By changing from transillumination with tungsten light to epifluorescent illumination and vice versa, both types of structures--Nissl bodies and lipofuscin--can be identified in the same section. The second technique uses pyronin Y for staining Nissl bodies in preparations previously stained with crystal violet. Nissl bodies are stained pink but lipofuscin remains violet. Lipofuscin in these sections also remains autofluorescent after the crystal violet stain has faded under violet or near-UV light.

Fracturing of revision of a cobalt-chrome femoral head after fracturing of a ceramic femoral head, with diffuse metallosis. Case report

Directory of Open Access Journals (Sweden)

Pedro Miguel Dantas Costa Marques

2013-04-01

Full Text Available We presente a case of a fracture of a cobalt-chrome femoral head after revision of a hip total prosthesis with ceramic femoral head fracture. During surgery we found the cobalt-chrome femoral head fracture, wear of the polyethylene and massive metallosis in muscular and cartilaginous tissue. Both femoral stem and acetabular cup were stable and without apparent wearing. After surgical debridement, we promoted the substitution of the femoral head and the acetabular polyethylene by similar ones. After 12 months of follow-up, the patient has no pain complaints, function limit or systemic signs associated with malign metallosis

Effects of enhances ultra violet irradiation on photosynthesis in ...

African Journals Online (AJOL)

Effects of enhances ultra violet irradiation on photosynthesis in anabaena variabilis and phormidium uncinatum. VA Donkor. Abstract. No Abstract. Journal of the Ghana Association Vol. 2 (3) 1999: pp.16-23. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

Microwave assisted spectrophotometric method for the determination of copper using leucocrystal violet

Directory of Open Access Journals (Sweden)

Sunitha B. Mathew

2007-04-01

Full Text Available A sensitive spectrophotometric method has been developed for the trace determination of copper using leucocrystal violet as chromogenic reagent. The proposed method is based on the reaction of copper(II with potassium iodide in acid medium to liberate iodine, which oxidizes leucocrystal violet to crystal violet dye having absorption maximum at 590 nm. The reaction between copper and potassium iodide is accelerated by irradiating the mixture with microwave energy for 15 s at 480 W. Beer’s law is obeyed in the concentration range 0.004 – 0.04 μg mL-1. The molar absorptivity, Sandell’s sensitivity, detection limit and quantitation limit were found to be 1.47 x 106 L mol-1 cm-1, 4.3 x 10-5 μg mL-2, 0.001 μg mL-1, 0.0043 μg mL-1, respectively. The optimum conditions and other analytical parameters were evaluated. The effect of interfering ions on the determination is described. The proposed method has been successfully applied for the determination of copper in environmental samples like tap water, agricultural run off water, plant materials and pharmaceutical samples.

76 FR 55003 - Carbazole Violet Pigment 23 From the People's Republic of China: Preliminary Intent To Rescind...

Science.gov (United States)

2011-09-06

... finished pigment in the form of presscake and dry color. Pigment dispersions in any form (e.g., pigments... DEPARTMENT OF COMMERCE International Trade Administration [A-570-892] Carbazole Violet Pigment 23... antidumping duty order on carbazole violet pigment 23 (CVP 23) from the People's Republic of China (PRC). This...

77 FR 1463 - Carbazole Violet Pigment 23 From the People's Republic of China: Final Rescission of Antidumping...

Science.gov (United States)

2012-01-10

... finished pigment in the form of presscake and dry color. Pigment dispersions in any form (e.g., pigments... DEPARTMENT OF COMMERCE International Trade Administration [A-570-892] Carbazole Violet Pigment 23... administrative review of the antidumping duty order on carbazole violet pigment 23 (CVP-23) from the People's...

Effects of blue or violet light on the inactivation of Staphylococcus aureus by riboflavin-5'-phosphate photolysis.

Science.gov (United States)

Wong, Tak-Wah; Cheng, Chien-Wei; Hsieh, Zong-Jhe; Liang, Ji-Yuan

2017-08-01

The light sensitive compound riboflavin-5'-phosphate (or flavin mononucleotide, FMN) generates reactive oxygen species (ROS) upon photo-irradiation. FMN is required by all flavoproteins because it is a cofactor of biological blue-light receptors. The photochemical effects of FMN after irradiation by blue or violet light on the inactivation of Staphylococcus aureus strains, including a methicillin-resistant strain (MRSA), were investigated in this study. Upon blue- or violet-light photo-treatment, FMN was shown to inactivate S. aureus due to the generated ROS. Effective bacterial inactivation can be achieved by FMN photolysis without an exogenous electron provider. Inactivation rates of 94.9 and 95.2% in S. aureus and MRSA, respectively, can be reached by blue light irradiation (2.0mW/cm 2 ) with 120μM FMN for 120min. A lower FMN concentration and a shorter time are required to reach similar effects by violet light irradiation. Inactivation rates of 96.3 and 97.0% in S. aureus and MRSA, respectively, can be reached by violet light irradiation (1.0mW/cm 2 ) with 30μM FMN for 30min. The sensitivity of the inherent photosensitizers is lower under blue-light irradiation. A long exposure photolytic treatment of FMN by blue light is required to inactivate S. aureus. Violet light was found to be more efficient in S. aureus inactivation at the same radiant intensity. FMN photolysis with blue or violet light irradiation enhanced the inactivation rates of S. aureus and MRSA. FMN photochemical treatment could be a supplemental technique in hygienic decontamination processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

Energy Technology Data Exchange (ETDEWEB)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K. [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India); Mandal, Asit Baran, E-mail: abmandal@hotmail.com [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India)

2012-05-15

Highlights: Black-Right-Pointing-Pointer Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. Black-Right-Pointing-Pointer Increased hydrothermal stability of collagen via intra and inter molecular crosslink. Black-Right-Pointing-Pointer D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. Black-Right-Pointing-Pointer D-AA in collagen creates new topologies inaccessible to homo chiral molecules. Black-Right-Pointing-Pointer Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T{sub s}) and denaturation temperature (T{sub d}) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T{sub s} of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

Spectral enhancement of leucocrystal violet treated footwear impression evidence in blood.

Science.gov (United States)

Spence, Lindsay; Asmussen, Gary

2003-03-27

The results presented demonstrate the capacity for spectral enhancement to substantially improve the forensic examination of footwear impressions in blood treated with leucocrystal violet (LCV). The UV-Vis absorption spectra were generated of (i) an aqueous solution of leucocrystal violet, (ii) leucocrystal violet in 3% H(2)O(2), (iii) LCV working solution and (iv) whole blood added to LCV working solution. The resultant fluorescence emission spectra were subsequently generated (lambda(ex)=630nm, lambda(em)=661-900nm). The results indicate that the UV-Vis absorption spectra of an unbuffered solution of whole blood with LCV working solution produces a strong absorbance curve with a maxima at 630nm. Subsequent excitation at this wavelength and generation of the emission spectrum in the fluorescence mode indicates that a solution of whole blood added to LCV working solution is an extremely weak fluorophore. Therefore, to enable an adequate and timely enhancement of blood impression evidence treated with LCV utilising either visible fluorescence or infrared luminescence requires (i) selection of the most appropriate excitation wavelength (lambda(ex)) and emission wavelength (lambda(em)) with extremely narrow band pass filters, which in the absence of substrate matrix interference is excitation at 630nm producing the emission maxima at 665nm and (ii) a visual enhancement system such as a CCD colour IR video camera with image integration.

Validation of HVOF WC/Co Thermal Spray Coatings as a Replacement for Hard Chrome Plating on Aircraft Landing Gear

National Research Council Canada - National Science Library

Sartwell, Bruce

2004-01-01

.... This document constitutes the final report on a project to quality high-velocity oxygen-fuel (HVOF) thermal spray WC/Co coatings as a replacement for hard chrome plating on landing gear components...

Sexual Dimorphism and Retinal Mosaic Diversification following the Evolution of a Violet Receptor in Butterflies.

Science.gov (United States)

McCulloch, Kyle J; Yuan, Furong; Zhen, Ying; Aardema, Matthew L; Smith, Gilbert; Llorente-Bousquets, Jorge; Andolfatto, Peter; Briscoe, Adriana D

2017-09-01

Numerous animal lineages have expanded and diversified the opsin-based photoreceptors in their eyes underlying color vision behavior. However, the selective pressures giving rise to new photoreceptors and their spectral tuning remain mostly obscure. Previously, we identified a violet receptor (UV2) that is the result of a UV opsin gene duplication specific to Heliconius butterflies. At the same time the violet receptor evolved, Heliconius evolved UV-yellow coloration on their wings, due to the pigment 3-hydroxykynurenine (3-OHK) and the nanostructure architecture of the scale cells. In order to better understand the selective pressures giving rise to the violet receptor, we characterized opsin expression patterns using immunostaining (14 species) and RNA-Seq (18 species), and reconstructed evolutionary histories of visual traits in five major lineages within Heliconius and one species from the genus Eueides. Opsin expression patterns are hyperdiverse within Heliconius. We identified six unique retinal mosaics and three distinct forms of sexual dimorphism based on ommatidial types within the genus Heliconius. Additionally, phylogenetic analysis revealed independent losses of opsin expression, pseudogenization events, and relaxation of selection on UVRh2 in one lineage. Despite this diversity, the newly evolved violet receptor is retained across most species and sexes surveyed. Discriminability modeling of behaviorally preferred 3-OHK yellow wing coloration suggests that the violet receptor may facilitate Heliconius color vision in the context of conspecific recognition. Our observations give insights into the selective pressures underlying the origins of new visual receptors. © The Author 2017. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Poultry feed based on protein hydrolysate derived from chrome-tanned leather solid waste: creating value from waste.

Science.gov (United States)

Chaudhary, Rubina; Pati, Anupama

2016-04-01

Leather industry generates huge amount of chrome-containing leather solid waste which creates major environment problems to tanners worldwide. Chrome-tanned leather solid waste is primarily chromium complex of collagen protein. The presence of chromium limits its protein application in animal feed industry. The purified protein hydrolysate with zero chromium could be used in poultry feed. In this study, an attempt has been made to assess performance of poultry with purified protein hydrolysate as a feed derived from chrome-tanned leather waste as partial replacement of soyabean meal as a sole source of protein for growing broiler chickens. Growth study was conducted to evaluate the effect of feeding protein hydrolysate on performance and physiochemical characteristics of meat of broiler chickens. Two experimental diets containing various levels of protein hydrolysate (EI-20 % and EII-30 %) were evaluated. The comparative study was performed as control with soyabean meal. Daily feed intake, body weight gain and feed conversion ratio were measured from day 8 to day 35. At the end of the study, birds were randomly selected and slaughtered to evaluate for physiochemical characteristics of meat. Diet had significant effects on feed intake and body weight gain. Birds fed with 20 and 30 % protein hydrolysate consumed 9.5 and 17.5 % higher amount of feed and gained 6.5 and 16.6 % higher than soyabean meal-fed birds. The current study produced evidence that protein hydrolysate can replace up to 75 % of soyabean meal in broiler diets without affecting either growth performance or meat characteristics.

Ultra violet radiation : effects on animals

International Nuclear Information System (INIS)

Stockdale, P.H.G.

1993-01-01

The paper deals with the evolutionary and historical events that have increased the susceptibility of certain genotypes of humanity and domestic animals to ultra violet radiation. Further it discusses the general effects of ultraviolet B (UVB) on vertebrates and then the clinical syndromes seen in such animals as a result of prolonged exposure to this form of radiation. Finally it gives anecdotal comments on evidence for changes in the immediately above types of disease and describes the need for a better recording system for these conditions so that these hypothetical changes could be effectively monitored. (author). 12 refs

75 FR 13257 - Carbazole Violet Pigment 23 from India: Final Results of the Expedited Five-year (Sunset) Review...

Science.gov (United States)

2010-03-19

...) and finished pigment in the form of presscake and dry color. Pigment dispersions in any form (e.g... DEPARTMENT OF COMMERCE International Trade Administration [C-533-839] Carbazole Violet Pigment 23... countervailing duty (CVD) order on Carbazole Violet Pigment 23 (CVP-23) [[Page 13258

Influence of Cooling Rate in High-Temperature Area on Hardening of Deposited High-Cutting Chrome-Tungsten Metal

OpenAIRE

Malushin, N. N.; Valuev, Denis Viktorovich; Valueva, Anna Vladimirovna; Serikbol, A.; Borovikov, I. F.

2015-01-01

The authors study the influence of cooling rate in high-temperature area for thermal cycle of high-cutting chrome-tungsten metal weld deposit on the processes of carbide phase merging and austenite grain growth for the purpose of providing high hardness of deposited metal (HRC 64-66).

Topical gentian violet compared with nystatin oral suspension for the treatment of oropharyngeal candidiasis in HIV-1-infected participants.

Science.gov (United States)

Mukherjee, Pranab K; Chen, Huichao; Patton, Lauren L; Evans, Scott; Lee, Anthony; Kumwenda, Johnstone; Hakim, James; Masheto, Gaerolwe; Sawe, Frederick; Pho, Mai T; Freedberg, Kenneth A; Shiboski, Caroline H; Ghannoum, Mahmoud A; Salata, Robert A

2017-01-02

Compare the safety and efficacy of topical gentian violet with that of nystatin oral suspension (NYS) for the treatment of oropharyngeal candidiasis in HIV-1-infected adults in resource-limited settings. Multicenter, open-label, evaluator-blinded, randomized clinical trial at eight international sites, within the AIDS Clinical Trials Group. Adult HIV-infected participants with oropharyngeal candidiasis, stratified by CD4 cell counts and antiretroviral therapy status at study entry, were randomized to receive either gentian violet (0.00165%, BID) or NYS (500 000 units, QID) for 14 days. Cure or improvement after 14 days of treatment. Signs and symptoms of oropharyngeal candidiasis were evaluated in an evaluator-blinded manner. The study was closed early per Data Safety Monitoring Board after enrolling 221 participants (target = 494). Among the 182 participants eligible for efficacy analysis, 63 (68.5%) in the gentian violet arm had cure or improvement of oropharyngeal candidiasis versus 61 (67.8%) in the NYS arm, resulting in a nonsizable difference of 0.007 (95% confidence interval: -0.129, 0.143). There was no sizable difference in cure rates between the two arms (-0.0007; 95% confidence interval: -0.146, 0.131). No gentian violet-related adverse events were noted. No sizable differences were identified in tolerance, adherence, quality of life, or acceptability of study drugs. In gentian violet arm, 61 and 39% of participants reported 'no' and 'mild-to-moderate' staining, respectively. Cost for medication procurement was significantly lower for gentian violet versus NYS (median $2.51 and 19.42, respectively, P = 0.01). Efficacy of gentian violet was not statistically different than NYS, was well tolerated, and its procurement cost was substantially less than NYS.

Hexavalent Chrome Free Coatings for Electronics Applications: Joint Test Report

Science.gov (United States)

Kessel, Kurt

2012-01-01

Regardless of the corrosivity of the environment, all metals require periodic maintenance activity to guard against the insidious effects of corrosion and thus ensure that alloys meet or exceed design or performance life. The standard practice for protecting metallic substrates is the application of a coating system. Applied coating systems work via a variety of methods (barrier, galvanic, and/or inhibitor) and adhere to the substrate through a combination of chemical and physical bonds. For years hexavalent chromium has been a widely used element within applied coating systems because of its self healing and corrosion resistant properties. Occupational Safety and Health Administration (OSHA) studies have concluded that hexavalent chromium (hex chrome) is carcinogenic and poses significant risk to human health. On May 5, 2011 amendments to the Defense Federal Acquisition Regulation Supplement (DFARS) were issued in the Federal Register. Subpart 223.73 prohibits contracts from requiring hexavalent chromium in deliverables unless certain exceptions apply. These exceptions include authorization from a general or flag officer and members of the Senior Executive Service from a Program Executive Office, and unmodified legacy systems. Otherwise, Subpart 252.223-7008 provides the contract clause prohibiting contractors from using or delivering hexavalent chromium in a concentration greater than 0.1 percent by weight for all new contracts and to be included down to subcontractors for supplies, maintenance and repair services, and construction materials. National Aeronautics and Space Administration (NASA), Department of Defense (DoD), and industry stakeholders continue to search for alternatives to hex chrome in coatings applications that meet their performance requirements in corrosion protection, cost, operability, and health and safety, while typically specifying that performance must be equal to or greater than existing systems.

Determination of tracer quantities of chromium in uranium; Dosage de traces de chrome dans l'uranium

Energy Technology Data Exchange (ETDEWEB)

Huart, A [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

A method is described for the photometric determination of chromium in uranium by absorbency at 540 m{mu} of the Cr(VI) diphenylcarbazide combination. After attack by nitric acid, the solution is made perchloric, and the chromium oxidised at the boiling point by permanganate. Excess oxidant is removed by hydrochloric acid. Study of operating conditions resulted in a method with an accuracy of {+-} 0,5 ppm for 0,5 to 15 ppm chromium in the metal. (author) [French] Le chrome est dose dans l'uranium par photometrie a 540 m{mu} du compose colore Cr(VI) diphenylcarbazide. Apres mise en solution critique et reprise perchlorique a chaud, le chrome est oxyde en milieu acide et a l'ebullition par le permanganate. L'exces d'oxydant est ensuite detruit par l'acide chlorhydrique a l'ebullition. L'etude des conditions experimentales aboutit a un mode operatoire strict. La precision obtenue pour des teneurs comprises entre 0,5 et 15 ppm dans le metal est de 0,5 ppm. (auteur)

Influence of Cooling Rate in High-Temperature Area on Hardening of Deposited High-Cutting Chrome-Tungsten Metal

International Nuclear Information System (INIS)

Malushin, N N; Valuev, D V; Valueva, A V; Serikbol, A; Borovikov, I F

2015-01-01

The authors study the influence of cooling rate in high-temperature area for thermal cycle of high-cutting chrome-tungsten metal weld deposit on the processes of carbide phase merging and austenite grain growth for the purpose of providing high hardness of deposited metal (HRC 64-66). (paper)

Chrome-free Samarium-based Protective Coatings for Magnesium Alloys

Science.gov (United States)

Hou, Legan; Cui, Xiufang; Yang, Yuyun; Lin, Lili; Xiao, Qiang; Jin, Guo

The microstructure of chrome-free samarium-based conversion coating on magnesium alloy was investigated and the corrosion resistance was evaluated as well. The micro-morphology, transverse section, crystal structure and composition of the coating were observed by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and X- ray photoelectron spectroscopy (XPS), respectively. The corrosion resistance was evaluated by potentiodynamic polarization curve and electrochemical impedance spectroscopy (EIS). The results reveal that the morphology of samarium conversion coating is of crack-mud structure. Tiny cracks distribute in the compact coating deposited by samarium oxides. XRD, EDS and XPS results characterize that the coating is made of amorphous and trivalent-samarium oxides. The potentiodynamic polarization curve, EIS and OCP indicate that the samarium conversion coating can improve the corrosion resistance of magnesium alloys.

Reversible polycolour change of viologens from violet through transparent to white

International Nuclear Information System (INIS)

Hoshino, Katsuyoshi; Oikawa, Yosuke; Sakabe, Ichiro; Komatsu, Toshiki

2009-01-01

The electrochromic properties of 1,1'-dibenzyl-4,4'-bipyridinium and 1,1'-diheptyl-4,4'-bipyridinium were investigated in the presence of MBr (M = Li + , Na + , and K + ). The cyclic voltammograms of these viologens showed a white-coloured state in addition to the usual violet one-electron reduction state and the colourless divalent state. Chemical analyses (FT-IR and XPS spectra) of the white film and some control experiments with different supporting electrolytes, MX (X = Cl - and I - ), revealed that the viologens formed water-insoluble ion pairs with tribromide generated by the electrooxidation of monobromide to produce a white film. The film was reversibly decolourized electrochemically to the initial transparent state, providing the polyelectrochromism using the simple viologen/MBr systems. The colouration efficiencies for the violet and the white-coloured states were 170 cm 2 /C and 104 cm 2 /C, respectively.

Large-area growth of multi-layered MoS{sub 2} for violet (∝405 nm) photodetector applications

Energy Technology Data Exchange (ETDEWEB)

Lee, Soo Hyun; Kim, Sanghun; Lee, Seunghyun; Yu, Jae Su [Department of Electronic Engineering, Kyung Hee University, Gyeonggi-do (Korea, Republic of)

2017-10-15

The two-dimensional multi-layered molybdenum disulfide (MoS{sub 2}) was grown over a large area by chemical vapor deposition process for violet (∝405 nm) photodetector (PD) applications. The high-quality MoS{sub 2} layers were successfully fabricated and transferred on HfO{sub 2}/Si substrate. The inherent surface structure originated from the surface oxidation was also analyzed. The electrical properties of the multi-layered MoS{sub 2}-based violet PDs with various channel widths (W{sub ch}) were measured and compared under dark state and violet illumination operating at 405 nm. For the device with W{sub ch} of 4 μm, at the bias of -5 V, the photocurrent and on/off ratio were obtained to be 54.0 nA and 55.2, respectively. Under violet illumination, the photocurrent was ∝4.6 times higher compared to green illumination. At the bias of -5 V, the photoresponse properties of the device were characterized with average rise time and reset time of ∝55.7 and 46.0 s, respectively, during four cycles of operation. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

Science.gov (United States)

Przepiórkowska, A; Chrońska, K; Zaborski, M

2007-03-06

The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

Vacuum ultra-violet and ultra-violet scintillation light detection by means of silicon photomultipliers at cryogenic temperature

Energy Technology Data Exchange (ETDEWEB)

Falcone, A., E-mail: andrea.falcone@pv.infn.it [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy); Bertoni, R. [INFN Sezione di Milano Bicocca, Piazza della Scienza, 3, 20126 Milano (Italy); Boffelli, F. [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy); Bonesini, M. [INFN Sezione di Milano Bicocca, Piazza della Scienza, 3, 20126 Milano (Italy); Cervi, T. [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); Menegolli, A. [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy); Montanari, C.; Prata, M.C.; Rappoldi, A.; Raselli, G.L.; Rossella, M.; Simonetta, M. [INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy); Spanu, M. [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); Torti, M. [University of Pavia, via Bassi, 6, 27100 Pavia (Italy); INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy); Zani, A. [INFN Sezione di Pavia, via Bassi, 6, 27100 Pavia (Italy)

2015-07-01

We tested the performance of two types of silicon photomultipliers, AdvanSiD ASD-NUV-SiPM3S-P and Hamamatsu 3×3 MM-50 UM VUV2, both at room (300 K) and at liquid nitrogen (77 K) temperature: breakdown voltage, quenching resistance, signal shape, gain and dark counts rate have been studied as function of temperature. The response of the devices to ultra-violet light is also studied. - Highlights: • We tested 2 SiPMs both at room and at cryogenic temperature. • Breakdown voltage, quenching resistance, gain and dark rate were measured. • Efficiency for VUV light detection was measured.

The Violet Experience: Social Interaction through Eclectic Music Learning Practices

Science.gov (United States)

Dakon, Jacob M.; Cloete, Elene

2018-01-01

In this qualitative case study, we used participant observation and interviews to examine Violet, a Flemish string youth orchestra. In doing so, we identify the qualities that constitute an 'eclectic' ensemble space, herein defined as a musical environment that uses a blend of informal and formal learning practices. Moreover, we emphasize how…

Nucleotide sequence of Hungarian grapevine chrome mosaic nepovirus RNA1.

Science.gov (United States)

Le Gall, O; Candresse, T; Brault, V; Dunez, J

1989-10-11

The nucleotide sequence of the RNA1 of hungarian grapevine chrome mosaic virus, a nepovirus very closely related to tomato black ring virus, has been determined from cDNA clones. It is 7212 nucleotides in length excluding the 3' terminal poly(A) tail and contains a large open reading frame extending from nucleotides 216 to 6971. The presumably encoded polyprotein is 2252 amino acids in length with a molecular weight of 250 kDa. The primary structure of the polyprotein was compared with that of other viral polyproteins, revealing the same general genetic organization as that of other picorna-like viruses (comoviruses, potyviruses and picornaviruses), except that an additional protein is suspected to occupy the N-terminus of the polyprotein.

Removal of methyl violet dye by adsorption onto N-benzyltriazole derivatized dextran

DEFF Research Database (Denmark)

Cho, Eunae; Tahir, Muhammad Nazir; Kim, Hwanhee

2015-01-01

In this work, N-benzyltriazole derivatized dextran was evaluated for its potential as a novel carbohydrate-based adsorbent for the removal of methyl violet dye from water. The modified dextran was synthesized by a click reaction of pentynyl dextran and benzyl azide, and the structure...... was characterized by nuclear magnetic resonance spectroscopy, elemental analysis, and scanning electron microscopy. Dextran was substituted with a triazole-linked benzyl group. For decolorization of the dye effluent, adsorption is a very effective treatment; here, the driving force is based on hydrogen bonding, pi...... stacking, and electrostatic interaction between the methyl violet dye and the N-benzyltriazole derivatized dextran. Batch experiments were carried out to investigate the required contact time and the effects of pH, initial dye concentrations, and temperature. The experimental data were analyzed...

Compositional Variation of Chrome Spinels in the Ore-bearing Zones of the Kraka Ophiolite and the Chromitite Origin

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2017-07-01

Full Text Available The article considers a chemical variation of accessory and ore-forming chrome spinels from the Kraka ultramafic massif at the different scales, from the deposit to the thin section. A correlation analysis of compositional and structural features of ultramafic rocks and ores was performed. The ultramafic rocks and chromitites in the studied massif show the distinct deformation structures and tectonite olivine fabric. A typical chemical gap (i.e. Cr#=Cr/(Cr+Al was observed between peridotite, on the one hand, and dunite and chromitite, on the other hand, on the scale of deposits and ore-bearing zones. The location and size of this gap depend on the type of deposit. The gap becomes wider from the disseminated tabular bodies to the typical podiform ones. It has been found that in the thin initial dunite veinlets in peridotite the chrome spinels chemistry changes gradually and there is no Cr# gap between peridotite and dunite. The dunite venlets show a strong olivine fabric, which is an evidence of their high-temperature plastic flow origin. It has been revealed that new chrome spinel grains previously formed as rods or needles and then coarsened. We explained this observation as the result of impurity segregation, coalescence and spheroidization induced by the plastic deformation of olivine. It is inferred that a solid crystal flow is the main requirement for the dunite and chromitite body formation in the Kraka ophiolite massif. In the solid stream, the mineral phase separation takes place. For example, olivine and orthopyroxene grains of parental peridotite separate from one another, and weaker (more mobile olivine grains form dunite bodies in which chromitite appears as a result of impurity segregation.

Chemical characterization and toxicologic evaluation of airborne mixtures: chemical characterization of combusted inventory red and violet smoke mixes

International Nuclear Information System (INIS)

Rubin, I.B.; Buchanan, M.V.; Moneyhun, J.H.

1982-10-01

Red and violet smoke grenades (Grenade, Hand, Smoke, M18) were combusted within canvas tents and the combustion products were sampled and analyzed. Uncombusted red and violet smoke mixes from the same lots used to fill the combusted grenades were also analyzed. Approximately ten percent of the major dye component of the red smoke mix, methylaminoanthraquinone (MAA) was converted to aminoanthraquinones (1-AA and 2-AA). The violet smoke mix was formulated to contain 1,4-diamino-2,3-dihydroanthraquinone (DAA) and MAA. Upon combustion the DAA was converted almost completely to diaminoanthraquinone (DAA) which was a minor constituent of the uncombusted mix. As in the combusted red smoke mix, it was found that MAA was partially converted to aminoanthraquinones

Characterization of emission factors related to source activity for trichloroethylene degreasing and chrome plating processes.

Science.gov (United States)

Wadden, R A; Hawkins, J L; Scheff, P A; Franke, J E

1991-09-01

A study at an automotive parts fabrication plant evaluated four metal surface treatment processes during production conditions. The evaluation provides examples of how to estimate process emission factors from activity and air concentration data. The processes were open tank and enclosed tank degreasing with trichloroethylene (TCE), chromium conversion coating, and chromium electroplating. Area concentrations of TCE and chromium (Cr) were monitored for 1-hr periods at three distances from each process. Source activities at each process were recorded during each sampling interval. Emission rates were determined by applying appropriate mass balance models to the concentration patterns around each source. The emission factors obtained from regression analysis of the emission rate and activity data were 16.9 g TCE/basket of parts for the open-top degreaser; 1.0 g TCE/1000 parts for the enclosed degreaser; 1.48-1.64 mg Cr/1000 parts processed in the hot CrO3/HNO3 tank for the chrome conversion coating; and 5.35-9.17 mg Cr/rack of parts for chrome electroplating. The factors were also used to determine the efficiency of collection for the local exhaust systems serving each process. Although the number of observations were limited, these factors may be useful for providing initial estimates of emissions from similar processes in other settings.

Adsorption and desorption characteristics of crystal violet in bottom ash column

Directory of Open Access Journals (Sweden)

Puthiya Veetil Nidheesh

2012-06-01

Full Text Available This study described adsorption of Crystal Violet (CV by bottom ash in fixed-bed column mode. Equilibrium of adsorption was studied in batch mode for finding adsorption capacity of bottom ash. In fixed bed column adsorption, the effects of bed height, feed flow rate, and initial concentration were studied by assessing breakthrough curve. The slope of the breakthrough curve decreased with increasing bed height. The breakthrough time and exhaustion time were decreased with increasing influent CV concentration and flow rates. The effect of bed depth, flow rate and CV concentration on the adsorption column design parameters were analyzed. Bed depth service time (BDST model was applied for analysis of crystal violet adsorption in the column. The adsorption capacity of bottom ash was calculated at 10% breakthrough point for different flow rates and concentrations. Desorption studies reveals that recovery of CV from bottom ash was effective by using CH3COOH than H2SO4, NaOH, HCl and NaCl solutions.

ADSORPTION AND DESORPTION CHARACTERISTICS OF CRYSTAL VIOLET IN BOTTOM ASH COLUMN

Directory of Open Access Journals (Sweden)

Puthiya Veetil Nidheesh

2012-01-01

Full Text Available This study described adsorption of Crystal Violet (CV by bottom ash in fixed-bed column mode. Equilibrium of adsorption was studied in batch mode for finding adsorption capacity of bottom ash. In fixed bed column adsorption, the effects of bed height, feed flow rate, and initial concentration were studied by assessing breakthrough curve. The slope of the breakthrough curve decreased with increasing bed height. The breakthrough time and exhaustion time were decreased with increasing influent CV concentration and flow rates. The effect of bed depth, flow rate and CV concentration on the adsorption column design parameters were analyzed. Bed depth service time (BDST model was applied for analysis of crystal violet adsorption in the column. The adsorption capacity of bottom ash was calculated at 10% breakthrough point for different flow rates and concentrations. Desorption studies reveals that recovery of CV from bottom ash was effective by using CH3COOH than H2SO4, NaOH, HCl and NaCl solutions.

Google Chrome OS: Cultural influence on product launch strategy between India and developed countries

OpenAIRE

Santhosh, Arjun

2011-01-01

In recent times product launch has become vital deciding factor in the success of a product. The significance of product launch becomes even higher if the product is radically new and different from existing products in the market. The aim of this dissertation is to look into the possible factors which might influence the product launch of Google Chrome Operating System that has radical concepts and design. The essential variations which might be needed for the successful launch in India as c...

PHOTOCATALYTIC REMOVAL OF TR I- AND HEXA-VALENT CHROMIUM IONS FROM CHROME-ELECTROPL ATING WASTEWATER

OpenAIRE

Puangrat Kajitvichyanukul; Chulaluck Changul

2017-01-01

A novel technique based on photocatalysis was applied to eliminate chromium ions, a toxic hazardous environmental pollutant. The photoreduction of each species of chromium (total, hexavalent, and trivalent chromiums) from chrome-electroplating wastewater was investigated using a titanium dioxide suspension under irradiation by a low-pressure mercury lamp. The initial concentration of total chromium was 300 mg/l. The applied conditions were the direct photocatalytic reduction process at pH 3.6...

Adsorption of violet B by agricultural waste of soft pistachio shells ...

African Journals Online (AJOL)

In this study, inexpensive agricultural waste pistachio sells was used for adsorption of violet B. Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM) were used to characterize the pistachio shells. The morphology of pistachio shell was studied by SEM and it showed the porous structure of ...

Comparison of staining of mitotic figures by haematoxylin and eosin-and crystal violet stains, in oral epithelial dysplasia and squamous cell carcinoma

Directory of Open Access Journals (Sweden)

Ankle Madhuri

2007-01-01

Full Text Available Mitosis of cells gives rise to tissue integrity. Defects during mitosis bring about abnormalities. Excessive proliferation of cells due to increased mitosis is one such outcome, which is the hallmark in precancer and cancer. The localization of proliferating cells or their precursors may not be obvious and easy. Establishing an easy way to distinguish these mitotic cells will help in grading and understanding their biological potential. Although immunohistochemistry is an advanced method in use, the cost and time factor makes it less feasible for many laboratories. Selective histochemical stains like toluidine blue, giemsa and crystal violet have been used in tissues including the developing brain, neural tissue and skin. Aim of the study: 1To compare the staining of mitotic cells in haematoxylin and eosin with that in crystal violet. 2To compare the number of mitotic figures present in normal oral mucosa, epithelial dysplasia and oral squamous cell carcinoma in crystal violet-stained sections with that in H and E-stained sections. Materials and Methods: Ten tissues of normal oral mucosa and 15 tissues each of oral epithelial dysplasia seen in tobacco-associated leukoplakia and squamous cell carcinoma were studied to evaluate the selectivity of 1% crystal violet for mitotic figures. The staining was compared with standard H and E staining. Statistical analysis was done using Man-Whitney U test. Results: A statistically significant increase in the mean mitotic count was observed in crystal violet-stained sections of epithelial dysplasia as compared to the H and E-stained sections ( p = 0.0327. A similar increase in the mitotic counts was noted in crystal violet-stained sections of oral squamous cell carcinoma as compared to the H and E-stained sections.( p = 0.0443. No significant difference was found in the mitotic counts determined in dysplasia or carcinoma by either the crystal violet ( p = 0.4429 or the H and E-staining techniques ( p = 0

NASA and ESA Collaboration on Hexavalent Chrome Alternatives - Pretreatments with Primers Screening Final Test Report

Science.gov (United States)

Rothgeb, Matthew J.; Kessel, Kurt R.

2015-01-01

Hexavalent chromium (hex chrome or Cr(VI)) is a widely used element within applied coating systems because of its self-healing and corrosion-resistant properties. The replacement of hex chrome in the processing of aluminum for aviation and aerospace applications remains a goal of great significance. Aluminum is the major manufacturing material of structures and components in the space flight arena. The National Aeronautics and Space Administration (NASA) and the European Space Agency (ESA) are engaged in a collaborative effort to test and evaluate alternatives to hexavalent chromium containing corrosion coating systems. NASA and ESA share common risks related to material obsolescence associated with hexavalent chromium used in corrosion-resistant coatings. In the United States, Occupational Safety and Health Administration (OSHA) studies have concluded that hexavalent chromium is carcinogenic and poses significant risk to human health. On May 5, 2011, amendments to the Defense Federal Acquisition Regulation Supplement (DFARS) were issued in the Federal Register. Subpart 223.73 prohibits contracts from requiring hexavalent chromium in deliverables unless certain exceptions apply. Subpart 252.223-7008 provides the contract clause prohibiting contractors and subcontractors from using or delivering hexavalent chromium in a concentration greater than 0.1 percent by weight for all new contracts associated with supplies, maintenance and repair services, and construction materials. ESA faces its own increasingly stringent regulations within European directives such as Registration, Evaluation, Authorization and Restriction of Chemical (REACH) substances and the Restriction of Hazardous Substances Directive (RoHS) which have set a mid-2017 sunset date for hexavalent chromium. NASA and ESA continue to search for an alternative to hexavalent chromium in coatings applications that meet their performance requirements in corrosion protection, cost, operability, and health and

Extraction-radiochemical study of the ion-association complex of antimony (V) with tetrazolium violet and its thermal behavior

International Nuclear Information System (INIS)

Kostova, S.G.; Boyanov, B.S.

1995-01-01

The optimum conditions for extraction of ion-associated complexes (IAS) formed from the tetrazolium salt - tetrazolium violet and Sb(V) in hydrochloric acid medium have been studied. An isotope of antimony ( 125 Sb) was used for determination of the recovery factor (R%) and distribution ratio (D S b). The thermal behavior of the antimony complex with tetrazole violet was studied using differential thermal and thermogravimetric analysis. (author) 12 refs.; 3 figs

Photodetector of ultra-violet radiation

International Nuclear Information System (INIS)

Dorogan, V.; Vieru, T.; Coseac, V.; Chirita, F.

1999-01-01

The invention relates to photodetectors on the semiconductors base, in particular, to photodetectors of ultra-violet radiation and can be used in the optoelectronics systems for determining the intensity and dose of ultraviolet radiation emitted by the Sun and other sources. In the structure of the photodetector of ultraviolet radiation with a superficial potential barrier formed of semiconductors A 3 B 5 with the prohibited power width Eg 1 , solid solutions thereof with the prohibited power width Eg 2 and SnO 2 or ITO, in the semiconductors A 3 B 5 at a surface distance less than the absorption length of the visible radiation it is formed an isotype heterojunction between the semiconductors A 3 B 5 and solid solutions thereof with the prohibited power width Eg 2 > Eg 1 . The technical result consists in manufacturing of a photodetector sensitive solely to the ultraviolet radiation

Sterilization of African Violet in the in Vitro Culture Using Synthesized Silver Nanoparticles by Two Plant Extracts

Directory of Open Access Journals (Sweden)

M. Solgi

2015-12-01

Full Text Available One of the major advantages of in vitro culture of African violet (Saintpaulha ionantha is production of new cultivars and propagation of their chimera which might not be propagated by the other methods. In this study, we tested the effects of silver nanoparticles on the sterilization rate (antifungal and antibacterial activity, regeneration and shoot formation of African violet "Pink Amiss" explants. These nanoparticles were synthesized from pomegranate peels and Damask rose petals extracts. We used a completely randomized design test with factorial arrangement to investigate various volumetric ratios of plant extracts to silver nitrate (1:20, 1:10, 1:5 and 1:1 on the culture contaminations. Using silver nanoparticles synthesized by the plant extracts, especially Damask rose petals extract resulted in no fungal and bacterial contamination in the African violet explants after 1 and 3 weeks as compared to the control, and silver nitrate (1mM. All tested concentrations of the silver nanoparticles significantly (P &le 0.05 controlled both bacterial and fungal contaminations. The 1:20 ratio of plant extracts to silver nitrate showed the best control. In addition, the highest regeneration (%52 and shoot regeneration (%38 was observed in this treatment. In conclusion, we suggest using silver nanoparticles synthesized by plant extracts for sterilization of in Vitro Culture for African Violet rather than using other chemicals such as silver nitrate.

Ultra-violet emission in Ho:ZBLAN fiber

International Nuclear Information System (INIS)

Kowalska, M.; Klocek, G.; Piramidowicz, R.; Malinowski, M.

2004-01-01

We report on the short wavelength (green, blue, and ultra-violet (UV)) emission in trivalent holmium doped fluoro-zirconate fiber (Ho 3+ :ZBLAN) under direct and upconversion pumping. Efficient red to UV upconversion has been observed using 647 nm cw pumping by krypton ion laser. A close to cubic UV signal intensity dependence on incident red pump power was determined, confirming the three-photon character of the observed process. The responsible upconversion mechanisms were investigated and shown to be excited state absorption (ESA) via low-lying 5 I 7 and 5 I 6 sates. Dynamics of the involved excited states have been studied under pulsed laser excitation

Application of saponin biosurfactant and its recovery in the MEUF process for removal of methyl violet from wastewater.

Science.gov (United States)

Samal, Kulbhushan; Das, Chandan; Mohanty, Kaustubha

2017-12-01

The potential of saponin, a biosurfactant, in the micellar enhanced ultrafiltration (MEUF) process was tested systematically for removal of methyl violet from wastewater. For this, the aqueous extract of reetha (Sapindus mukorossi) pericarp which contains saponin was used as the biosurfactant. First, the micellar solubilization of methyl violet in saponin micelles was investigated in terms of molar solubilization power (SP) of saponin. It was observed that the adsorption of methyl violet on the agglomerates of saponin micelles was mainly responsible for the enhanced solubilization. The Gibbs free energy of solubilization (calculated as -29.63 kJ mol -1 ) suggested that process was feasible and spontaneous. The MEUF experiments were performed in batch as well as continuous mode using saponin biosurfactant, and the effect of operating parameters on permeate flux and solute retention were evaluated. The removal of methyl violet in MEUF process was >99% achieved with 10 kDa polyethersulfone (PES) membrane for feed dye concentration of 250 mg L -1 at studied conditions. Finally, the saponin in permeate was recovered using n-heptane and n-butanol by solvent extraction process. The solvent n-butanol showed better extraction efficiency as compared to n-heptane for saponin extraction. Copyright © 2017 Elsevier Ltd. All rights reserved.

Detection of low concentration of malachite green and crystal violet in water

Czech Academy of Sciences Publication Activity Database

Šafařík, Ivo; Šafaříková, Miroslava

2002-01-01

Roč. 36, - (2002), s. 196-200 ISSN 0043-1354 R&D Projects: GA ČR GA203/98/1145 Institutional research plan: CEZ:AV0Z6087904 Keywords : magnetic particles * crystal violet Subject RIV: EH - Ecology, Behaviour Impact factor: 1.611, year: 2002

Ultra-violet radiation for the inactivation of microorganisms in hydroponics

International Nuclear Information System (INIS)

Buyanosvsky, G.; Gale, J.; Degani, N.

1981-01-01

The growth of microorganisms in the nutrient solution of a circulating hydroponic system was suppressed by ultra-violet radiation. Applied for three hours daily (572 Jm -2 h -1 ) throughout experiments in which tomato and corn were grown, it was effective in reducing the population of microorganisms from between 500-800 x 10 3 to 10-50 x 10 3 cells per ml. (orig.)

Ultra-violet radiation for the inactivation of microorganisms in hydroponics

Energy Technology Data Exchange (ETDEWEB)

Buyanosvsky, G; Gale, J [Ben-Gurion Univ. of the Negev, Beersheva (Israel). Jacob Blaustein Inst. for Desert Research; Degani, N [Israel Atomic Energy Commission, Beersheba. Nuclear Research Center-Negev

1981-01-01

The growth of microorganisms in the nutrient solution of a circulating hydroponic system was suppressed by ultra-violet radiation. Applied for three hours daily (572 Jm/sup -2/h/sup -1/) throughout experiments in which tomato and corn were grown, it was effective in reducing the population of microorganisms from between 500-800 x 10/sup 3/ to 10-50 x 10/sup 3/ cells per ml.

REMOVAL OF CRYSTAL VIOLET BY BIOSORPTION ONTO DATE STONES

OpenAIRE

NOUREDDINE EL MESSAOUDI; MOHAMMED EL KHOMRI; SAFAE BENTAHAR; ABDELLAH DBIK; ABDELLAH LACHERAI

2016-01-01

The biosorption has the advantage that it can be applied to effluent disposal and thus brings various responses to the regulatory requirements for environmental protection. This study presents the results obtained from the use of date stones (DS) for the elimination of crystal violet (CV) from aqueous medium. Several analysis techniques were used to determine the different characteristics of biosorbent studied (FTIR, TGA-DTA, SEM and pHzpc).The physico-chemical parameters influence of the bio...

Photocatalytic degradation of crystal violet by thiourea-doped TiO2 ...

African Journals Online (AJOL)

In this study, optimisation of the photocatalytic behaviour of crystal violet (CV) by thiourea (Tu)-codoped TiO2 thin film in fixed bed photoreactor was investigated by central composite designs (CCDs). The effective variables were pH, the concentration of CV dye, flow rate and reaction time. The results of the CCD model ...

Interliposomal transfer of crystal violet dye from DPPC liposomes to magnetoliposomes

International Nuclear Information System (INIS)

Koneracka, Martina; Kopcansky, Peter; Sosa, Pavol; Bagelova, Jaroslava; Timko, Milan

2005-01-01

Magnetoliposomes offer new challenges in the field of modern biotechnology and biomedicine. To investigate the important mechanism of interliposomal transfer of encapsulated substances, we investigated in the present work magnetoliposomes and liposomes containing the dye crystal violet. Our study of transmembrane transport showed that the dye transfer from DPPC liposomes to magnetoliposomes was temperature dependent

Violet and visible up-conversion emission in Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses

Energy Technology Data Exchange (ETDEWEB)

Yang Yanmin, E-mail: mihuyym@163.co [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Zhang Meixin [Forensic Science Lab, Hebei University, Baoding 071002 (China); Yang Zhiping [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Fu Zuoling [Key Laboratory of Coherent Light, Atomic and Molecular Spectroscopy, College of physics, Jilin University, Ministry of Education, Changchun 130023 (China)

2010-10-15

The up-conversion emission properties of Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses have been investigated with 980 nm excitation. The violet, blue, green and red emission bands at about 350, 485, 544 and 653 nm can be identified, respectively. Experimental results indicated that the relative intensity ratios of the peaks I{sub Red}/I{sub Green} increased with increasing B{sub 2}O{sub 3} concentration, which led to changing color of up-conversion emission from green at x=0 to yellow at x=40, to red at x=60. The violet emission at 350 nm was first reported in germanium-borate glass host and up-conversion mechanisms of the emissions were discussed. The Yb{sup 3+}-Ho{sup 3+} co-doped germanium-borate glasses could be an alternative for the generation of violet and primary colors for application in solid-state displays.

PLGA nano/microparticles loaded with cresyl violet as a tracer for drug delivery: Characterization and in-situ hyperspectral fluorescence and 2-photon localization

Energy Technology Data Exchange (ETDEWEB)

Lunardi, Claure N., E-mail: clunardi@unb.br [Laboratory of Photochemistry and Nanobiotechnology, University of Brasília, Brasília (Brazil); Department of Biomedical Engineering and Radiology, Laboratory for Functional Optical Imaging, Columbia University, New York, NY (United States); Gomes, Anderson J. [Laboratory of Photochemistry and Nanobiotechnology, University of Brasília, Brasília (Brazil); Department of Biomedical Engineering and Radiology, Laboratory for Functional Optical Imaging, Columbia University, New York, NY (United States); Palepu, Sandeep; Galwaduge, P. Thilanka; Hillman, Elizabeth M.C. [Department of Biomedical Engineering and Radiology, Laboratory for Functional Optical Imaging, Columbia University, New York, NY (United States)

2017-01-01

Here we present the production, characterization and in-vivo assessment of cresyl violet-loaded biodegradable PLGA nano/microparticles (CV-NP and CV-MP). We demonstrate that the beneficial spectral characteristics of cresyl violet make it suitable as a tracer for particle-based drug delivery using both hyperspectral wide field and two-photon excited fluorescence microscopy. Particles were prepared using a cosolvent method, after which the physicochemical properties such as morphology, particle size, drug entrapment efficiency, drug loading and in vitro drug release behavior were measured in addition to spectroscopic properties, such as absorption, fluorescence and infrared spectra. The particles were then tested in an in vivo mouse model to assess their biodistribution characteristics. The location and integrity of particles after injection was determined using both hyperspectral fluorescence and two-photon microscopy within intact organs in situ. Our results show that cresyl violet is efficiently entrapped into PLGA particles, and that the particles are spherical in shape, ranging from 300 to 5070 nm in diameter. Particle biodistribution in the mouse was found to depend on particle size, as expected. Cresyl violet is shown to be an ideal tracer to assess the properties PLGA particle-based drug delivery in combination with our novel multi-scale optical imaging techniques for in-situ particle localization. - Highlights: • Cresyl violet entrapment into polymeric particles • Cresyl violet suitable as a tracer for particle-based drug delivery • Hyperspectral analysis of polymer nano/microparticles • Two-photon microscopy of polymeric nano/microparticles.

Wearable device for monitoring momentary presence of intense x-ray and/or ultra-violet radiations

International Nuclear Information System (INIS)

Shriner, W.

1981-01-01

A credit-card-size clear-plastic-encased device can be worn or carried by a person to warn him of the momentary presence of dangerous intensities of ultra-violet and/or x-ray radiations. A base lamina (e.g. of cardboard) is coated with a material (e.g. zinc-cadmium sulfide or lead-barium sulfate) which fluoresces under such radiations. Numerals, letters, words or symbols are printed over the fluorescent coat with a material inhibitory to said radiations so that a warning message in dark print will appear on a light background when dangerous intensities of said radiations are present. An x-ray-warning area is covered with an ultra-violet absorbing screen so that said area will glow only under x-rays (Which rays will also activate the remaining ultra-violet-responsive area). The colors of the laminas and the coats are so selected that the messages are not visible when dangerous radiations are not present. If desired, only the message can be printed with fluorescent material so as to glow on a darker background. Optionally, step-layer attenuation devices can be added to indicate degrees of radiation; and reflecting surfaces can underlie the fluorescent coat to increase efficiency and/or sensitively

Flash photolysis of carbon dioxide in the far ultra-violet

International Nuclear Information System (INIS)

Barat, F.

1970-01-01

The flash photolysis of CO 2 (3 torr) in the far ultra-violet, down to the transparency limit of lithium fluoride, produces vibrationally excited CO in its Χ 1 Σ electronic ground state and an electronically excited oxygen atom O( 1 D). After photolysis, the changes in the concentration of vibrationally de-excited CO in the 0 to 200 μsec, time range are followed using absorption spectroscopy. These changes can be explained on the basis of three main competing reactions: CO(Χ 1 Σ, ν'' = 0) + O( 1 D) → CO 2 ( 1 Σ g + ), O( 1 D) + CO 2 → O( 3 P) + CO 2 and CO 3 , CO(X 1 Σ, ν'' = 1,2) + CO 2 → CO(Χ 1 Σ, ν'' = 0) + CO 2 . The values of the rate constants for these three reactions are determined by analog calculations. The effect of O( 1 D) scavenging or quenching gases on the oxidation reaction of CO by O( 1 D) is examined. A study of the flash photolysis of O 2 in the presence of CO in the far ultra-violet makes it possible to eliminate the hypothesis that CO 3 is involved in the reaction leading to the disappearance of CO after photolysis. (author) [fr

A comparative analysis of five chrome green pigments based on different spectroscopic techniques

International Nuclear Information System (INIS)

Desnica, V.; Furic, K.; Hochleitner, B.; Mantler, M.

2003-01-01

A detailed study of five chrome-based green pigments belonging to a large pigment collection at the Academy of Fine Arts in Vienna, Austria has been performed. The samples were analyzed and compared using the two X-ray methods--X-ray fluorescence and X-ray diffraction, and the two optical methods--Raman spectroscopy and infrared spectroscopy. The composition differences between the similarly denoted samples of the collection were determined and the significant sensitivity differences of the investigated methods to specific compounds have been established. This relative discrepancy of the obtained results depending on the technique used proved once again the need of a combined use of the investigated methods

Kinetic studies on the degradation of crystal violet by the Fenton oxidation process.

Science.gov (United States)

Wu, H; Fan, M M; Li, C F; Peng, M; Sheng, L J; Pan, Q; Song, G W

2010-01-01

The degradation of dye crystal violet (CV) by Fenton oxidation process was investigated. The UV-Vis spectrogram has shown that CV can be degraded effectively by Fenton oxidation process. Different system variables namely initial H(2)O(2) concentration, initial Fe(2 + ) concentration and reaction temperature, which have effect on the degradation of CV by Fenton oxidation process, have been studied systematically. The degradation kinetics of CV was also elucidated based on the experimental data. The degradation of CV obeys the first-order reaction kinetics. The kinetic model can be described as k=1.5 exp(-(7.5)/(RT))[H(2)O(2)](0)(0.8718)[Fe(2+)](0)(0.5062). According to the IR spectrogram, it is concluded that the benzene ring of crystal violet has been destroyed by Fenton oxidation. The result will be useful in treating dyeing wastewater containing CV by Fenton oxidation process.

Effects of chronic gamma irradiation on adventitious plantlet formation of Saintpaulia ionantha (African violet) detached leaves

International Nuclear Information System (INIS)

Arunee Wongpiyasatid; Peeranuch Jompuk; Katarat Chusreeaeom; Thanya Taychasinpitak

2007-01-01

Formation of adventitious plantlets on unrootedly detached leaves of two African violet (Saintpaulia ionantha) cultivars, pink and violet flowers, chronically gamma-irradiated in gamma room at The Gamma Irradiation Service and Nuclear Technology Research Center, Kasetsart University was compared. Detached leaves were immediately planted after detachment in plastic trays containing peat moss, 18 leaves per treatment with 3 replications. Three dose rates (rad/h) with 3 doses (rad)/dose rate, were applied to the irradiated samples while the controls were placed outside the gamma room. Three months after irradiation, the number of survived leaves, the number of leaves producing adventitious plantlets and the number of plantlets per leaf were recorded. After that, the young plantlets were transferred to the new pots for further observation on plant growth and mutation characters. The results revealed that the number of survived leaves, the number of leaves producing adventitious plantlets and the number of plantlets per leaf varied slightly with radiation doses but were not significantly different at different dose rates. Radiosensitivity was noticed to be higher in pink flower cultivar than the violet one. M 1 V 1 plantlets will be followed up for growth and mutation character observations

Optimization of the Ultrasonic-Assisted Extraction of Phenolic Compounds from Oryza Sativa L. ‘Violet Nori’ and Determination of the Antioxidant Properties of its Caryopses and Leaves

Directory of Open Access Journals (Sweden)

Federica Turrini

2018-04-01

Full Text Available ‘Violet Nori’ is a new spontaneous growing violet rice variety showing a peculiar violet color in its fresh leaves as well. In this paper, the antioxidant properties and the content of total phenols, radical scavengers, and anthocyanins in ‘Violet Nori’ caryopses, flour, and leaves are explored and compared. Ultrasonic-Assisted Extraction (UAE is employed for the extraction of phenolic compounds, improving the extraction conditions by Design of Experiments (DoE. The obtained results show that the Radical Scavenging Activities (RSAs, the Total Phenolic Contents (TPCs, and the anthocyanin amounts (1000–1500 μg/g, expressed as cyanidin-3-glucoside of ‘Violet Nori’ caryopses are higher than those in the other analyzed colored rice samples (300–900 μg/g as cyanidin-3-glucoside, with the exception of the cultivars ‘Artemide’ and ‘Nerone’, which show comparable values of RSAs and TPCs. The study of ‘Violet Nori’ leaves at different plant maturation stages shows that their anthocyanin content is 2–3 times higher than in the caryopses and in the flour, reaching the highest levels at about 60 days from seeding. Thus, the estimated extraction yield of 4 kg anthocyanins/t makes fresh leaves very interesting for the extraction of anthocyanins on an industrial scale, whereas violet caryopses are a very interesting dietetic source of valuable anthocyanins and other antioxidant compounds.

Dosimetric characteristics of aqueous solution of crystal violet for applications in food irradiation

Energy Technology Data Exchange (ETDEWEB)

Khan, H M; Naz, Shagufta; Tabassum, Safia [Peshawar University, Peshawar (Pakistan). Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry

2011-07-15

Aqueous solution of crystal violet has been evaluated spectrophotometrically as a gamma-ray chemical dosimeter. The response of the chemical dosimetric system has also been investigated under different environmental conditions, such as light and temperature. In the present study the response has been measured at two wavelengths; 588 nm ({lambda}{sub max} of the irradiated solution) and 500 nm. The response of the crystal violet dosimeter was linear in the dose range of 50-550 Gy at pH 5.6 when absorption measurements were made at 588 and 500 nm. The response of the crystal violet dosimeter during post-irradiation storage at room temperature in dark showed slight decrease in absorbance at 588 and 510 nm but the response was almost stable at 460 nm. For higher doses, the change in the response was greater as compared to the low doses. Post-irradiation stability during diffused sunlight showed significant decrease in the response for higher dose at 588 and 510 nm and slower decrease in the response for lower dose at the above mentioned wavelengths. However the response was almost stable up to 97 days at 460 nm for higher and lower doses. At 4 deg C, the decrease in the absorbance was slower at 588 and 510 nm while the response was almost constant at 460 nm. At higher temperatures, such as 40 deg C, the decrease in the absorbance was greater at 588 and 510 nm while at 460 nm the absorbance was almost constant for about 3 months. (author)

Dosimetric characteristics of aqueous solution of crystal violet for applications in food irradiation

International Nuclear Information System (INIS)

Khan, H.M.; Shagufta Naz; Safia Tabassum

2011-01-01

Aqueous solution of crystal violet has been evaluated spectrophotometrically as a gamma-ray chemical dosimeter. The response of the chemical dosimetric system has also been investigated under different environmental conditions, such as light and temperature. In the present study the response has been measured at two wavelengths; 588 nm (λ max of the irradiated solution) and 500 nm. The response of the crystal violet dosimeter was linear in the dose range of 50-550 Gy at pH 5.6 when absorption measurements were made at 588 and 500 nm. The response of the crystal violet dosimeter during post-irradiation storage at room temperature in dark showed slight decrease in absorbance at 588 and 510 nm but the response was almost stable at 460 nm. For higher doses, the change in the response was greater as compared to the low doses. Post-irradiation stability during diffused sunlight showed significant decrease in the response for higher dose at 588 and 510 nm and slower decrease in the response for lower dose at the above mentioned wavelengths. However the response was almost stable up to 97 days at 460 nm for higher and lower doses. At 4 deg C, the decrease in the absorbance was slower at 588 and 510 nm while the response was almost constant at 460 nm. At higher temperatures, such as 40 deg C, the decrease in the absorbance was greater at 588 and 510 nm while at 460 nm the absorbance was almost constant for about 3 months. (author)

Determination of hexavalent chromium in exhaled breath condensate and environmental air among chrome plating workers.

Science.gov (United States)

Goldoni, Matteo; Caglieri, Andrea; Poli, Diana; Vettori, Maria Vittoria; Corradi, Massimo; Apostoli, Pietro; Mutti, Antonio

2006-03-15

Chromium speciation has attracted attention because of the different toxicity of Cr(III), which is considered relatively non-toxic, and Cr(VI), which can cross cell membranes mainly as a chromate anion and has been classified as a class I human carcinogen. The aims of the present study were to measure soluble Cr(VI) levels in environmental samples, to develop a simple method of quantifying Cr(VI) in exhaled breath condensate (EBC), and to follow the kinetics of EBC Cr(VI) in chrome plating workers.Personal air samples were collected from 10 chrome platers; EBC was collected from the same workers immediately after the work shift on Tuesday and before the work shift on the following Wednesday. Environmental and EBC Cr(VI) levels were determined by means of colorimetry and electrothermal absorption atomic spectrometry, respectively.The method of detecting Cr(VI) in environmental air was based on the extraction of the Cr(VI)-diphenylcarbazide (Cr(VI)-DPC) complex in 1-butanol, whereas EBC Cr(VI) was determined using a solvent extraction of Cr(VI) as an ion pair with tetrabutylammonium ion, and subsequent direct determination of the complex (Cr(VI)-DPC) in EBC.Kinetic data showed that airborne Cr(VI) was reduced by 50% in airway lining fluid sampled at the end of exposure and that there was a further 50% reduction after about 15 h. The persistence of Cr(VI) in EBC supports the use of EBC in assessing target tissue levels of Cr(VI).

Determination of hexavalent chromium in exhaled breath condensate and environmental air among chrome plating workers

International Nuclear Information System (INIS)

Goldoni, Matteo; Caglieri, Andrea; Poli, Diana; Vettori, Maria Vittoria; Corradi, Massimo; Apostoli, Pietro; Mutti, Antonio

2006-01-01

Chromium speciation has attracted attention because of the different toxicity of Cr(III), which is considered relatively non-toxic, and Cr(VI), which can cross cell membranes mainly as a chromate anion and has been classified as a class I human carcinogen. The aims of the present study were to measure soluble Cr(VI) levels in environmental samples, to develop a simple method of quantifying Cr(VI) in exhaled breath condensate (EBC), and to follow the kinetics of EBC Cr(VI) in chrome plating workers. Personal air samples were collected from 10 chrome platers; EBC was collected from the same workers immediately after the work shift on Tuesday and before the work shift on the following Wednesday. Environmental and EBC Cr(VI) levels were determined by means of colorimetry and electrothermal absorption atomic spectrometry, respectively. The method of detecting Cr(VI) in environmental air was based on the extraction of the Cr(VI)-diphenylcarbazide (Cr(VI)-DPC) complex in 1-butanol, whereas EBC Cr(VI) was determined using a solvent extraction of Cr(VI) as an ion pair with tetrabutylammonium ion, and subsequent direct determination of the complex (Cr(VI)-DPC) in EBC. Kinetic data showed that airborne Cr(VI) was reduced by 50% in airway lining fluid sampled at the end of exposure and that there was a further 50% reduction after about 15 h. The persistence of Cr(VI) in EBC supports the use of EBC in assessing target tissue levels of Cr(VI)

Feasibility of Biological Effective Monitoring of Chrome Electroplaters to Chromium through Analysis of Serum Malondialdehyde.

Science.gov (United States)

Mozafari, P; Rezazadeh Azari, M; Shokoohi, Y; Sayadi, M

2016-10-01

Great concern about occupational exposure to chromium (Cr [VI]) has been reported due to escalated risk of lung cancer in exposed workers. Consequences of occupational exposure to Cr (VI) have been reported as oxidative stress and lung tissue damage. To investigate the feasibility of biological effect monitoring of chrome electroplaters through analysis of serum malondialdehyde (MDA). 90 workers directly involved in chrome electroplating---categorized into three equal groups based on their job as near bath workers, degreaser, and washers---and 30 workers without exposure to Cr (VI), served as the control group, were studied. Personal samples were collected and analyzed according to NIOSH method 7600. Serum MDA level was measured by HPLC using a UV detector. Median Cr (VI) exposure level was 0.38 mg/m(3) in near bath workers, 0.20 mg/m(3) in degreasers, and 0.05 mg/m(3) in washers. The median serum MDA level of three exposed groups (2.76 μmol/L) was significantly (p<0.001) higher than that in the control group (2.00 μmol/L). There was a positive correlation between electroplaters' level of exposure to Cr (VI) and their serum MDA level (Spearman's ρ 0.806, p<0.001). Serum MDA level is a good biomarker for the level of occupational exposure to Cr (VI) in electroplaters.

Determination of hexavalent chromium in exhaled breath condensate and environmental air among chrome plating workers

Energy Technology Data Exchange (ETDEWEB)

Goldoni, Matteo [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy); National Institute of Occupational Safety and Prevention, Research Centre at University of Parma, Parma (Italy); Caglieri, Andrea [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy); Poli, Diana [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy); National Institute of Occupational Safety and Prevention, Research Centre at University of Parma, Parma (Italy); Vettori, Maria Vittoria [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy); National Institute of Occupational Safety and Prevention, Research Centre at University of Parma, Parma (Italy); Corradi, Massimo [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy); National Institute of Occupational Safety and Prevention, Research Centre at University of Parma, Parma (Italy); Apostoli, Pietro [Laboratory of Industrial Hygiene, Department of Experimental and Applied Medicine, University of Brescia (Italy); Mutti, Antonio [Laboratory of Industrial Toxicology, Department of Clinical Medicine, Nephrology and Health Sciences, University of Parma, Via Gramsci 14, 43100 Parma (Italy)]. E-mail: antonio.mutti@unipr.it

2006-03-15

Chromium speciation has attracted attention because of the different toxicity of Cr(III), which is considered relatively non-toxic, and Cr(VI), which can cross cell membranes mainly as a chromate anion and has been classified as a class I human carcinogen. The aims of the present study were to measure soluble Cr(VI) levels in environmental samples, to develop a simple method of quantifying Cr(VI) in exhaled breath condensate (EBC), and to follow the kinetics of EBC Cr(VI) in chrome plating workers. Personal air samples were collected from 10 chrome platers; EBC was collected from the same workers immediately after the work shift on Tuesday and before the work shift on the following Wednesday. Environmental and EBC Cr(VI) levels were determined by means of colorimetry and electrothermal absorption atomic spectrometry, respectively. The method of detecting Cr(VI) in environmental air was based on the extraction of the Cr(VI)-diphenylcarbazide (Cr(VI)-DPC) complex in 1-butanol, whereas EBC Cr(VI) was determined using a solvent extraction of Cr(VI) as an ion pair with tetrabutylammonium ion, and subsequent direct determination of the complex (Cr(VI)-DPC) in EBC. Kinetic data showed that airborne Cr(VI) was reduced by 50% in airway lining fluid sampled at the end of exposure and that there was a further 50% reduction after about 15 h. The persistence of Cr(VI) in EBC supports the use of EBC in assessing target tissue levels of Cr(VI)

Feasibility of Biological Effective Monitoring of Chrome Electroplaters to Chromium through Analysis of Serum Malondialdehyde

Directory of Open Access Journals (Sweden)

P Mozafari

2016-10-01

Full Text Available Background: Great concern about occupational exposure to chromium (Cr [VI] has been reported due to escalated risk of lung cancer in exposed workers. Consequences of occupational exposure to Cr (VI have been reported as oxidative stress and lung tissue damage. Objective: To investigate the feasibility of biological effect monitoring of chrome electroplaters through analysis of serum malondialdehyde (MDA. Methods: 90 workers directly involved in chrome electroplating—categorized into three equal groups based on their job as near bath workers, degreaser, and washers—and 30 workers without exposure to Cr (VI, served as the control group, were studied. Personal samples were collected and analyzed according to NIOSH method 7600. Serum MDA level was measured by HPLC using a UV detector. Results: Median Cr (VI exposure level was 0.38 mg/m3 in near bath workers, 0.20 mg/m3 in degreasers, and 0.05 mg/m3 in washers. The median serum MDA level of three exposed groups (2.76 μmol/L was significantly (p<0.001 higher than that in the control group (2.00 μmol/L. There was a positive correlation between electroplaters' level of exposure to Cr (VI and their serum MDA level (Spearman's ρ 0.806, p<0.001. Conclusion: Serum MDA level is a good biomarker for the level of occupational exposure to Cr (VI in electroplaters.

Toward the Extreme Ultra Violet Four Wave Mixing Experiments: From Table Top Lasers to Fourth Generation Light Sources

Directory of Open Access Journals (Sweden)

Riccardo Cucini

2015-01-01

Full Text Available Three different Transient Grating setups are presented, with pulsed and continuous wave probe at different wavelengths, ranging from infrared to the extreme ultra violet region. Both heterodyne and homodyne detections are considered. Each scheme introduces variations with respect to the previous one, allowing moving from classical table top laser experiments towards a new four wave mixing scheme based on free electron laser radiation. A comparison between the various setups and the first results from extreme ultra violet transient grating experiments is also discussed.

Decolorization of Malachite Green and Crystal Violet by Waterborne Pathogenic Mycobacteria

Science.gov (United States)

Jones, Jefferson J.; Falkinham III, Joseph O.

2003-01-01

Mycobacterium avium, Mycobacterium intracellulare, Mycobacterium scrofulaceum, Mycobacterium marinum, and Mycobacterium chelonae tolerate high concentrations of the dyes malachite green and crystal violet. Cells of strains of those species decolorized (reduced) both malachite green and crystal violet. Because decolorized malachite green lacked antimicrobial activity, the resistance of these mycobacteria could be due, in part, to their ability to decolorize the dyes. Small amounts of malachite green and its reduced, decolorized product were detected in the lipid fraction of M. avium strain A5 cells grown in the presence of malachite green, suggesting that a minor component of resistance could be due to sequestering the dyes in the extensive mycobacterial cell surface lipid. The membrane fraction of M. avium strain A5 had at least a fivefold-higher specific decolorization rate than did the crude extract, suggesting that the decolorization activity is membrane associated. The malachite green-decolorizing activity of the membrane fraction of M. avium strain A5 was abolished by either boiling or proteinase exposure, suggesting that the decolorizing activity was due to a protein. Decolorization activity of membrane fractions was stimulated by ferrous ion and inhibited by dinitrophenol and metyrapone. PMID:12821489

154 Effet du chrome niacinate sur la tolérance au glucose chez le rat ...

African Journals Online (AJOL)

PR BOKO

contribution to the DEX treated groups. CrN supplementation did not correct the elevation of blood glucose ... chrome niacinate (30mg/kg/j, PO) pendant 14 jours, n=10. 2-2-2. Prélèvements. 1mL de sang a été prélevé à partir de la veine caudale sur tube hépariné à j0, j7, j14, j21 et j28. Les prélèvements ont été centrifugés ...

Elevated Frequencies of Micronuclei and other Nuclear Abnormalities of Chrome Plating Workers Occupationally Exposed to Hexavalent Chromium

OpenAIRE

Sudha, S; Kripa, SK; Shibily, P; Shyn, J

2011-01-01

Background Biomonitoring provides a useful tool to estimate the genetic risk from exposure to genotoxic agents. The aim of this study was to assess the potential cytogenetic damage associated with occupational exposure to hexavalent chromium by using micronuclei (MN) as a biomarker. Methods This was a cross-sectional study and all participants were males. Both the exposed and control individuals were selected from Coimbatore, Southern India. Exfoliated buccal cells from 44 chrome plating work...

Spectrophotometric determination of boron by solvent extraction with hydrobenzoin and crystal violet

International Nuclear Information System (INIS)

Sato, Shigeya; Uchikawa, Sumio

1982-01-01

A highly sensitive and simple method for the spectrophotometric determination of boron was developed. Boron was found to react with hydrobenzoin in weak alkaline medium to form a complex anion extractable into benzene with crystal violet, and the measurement of the absorbance of crystal violet in the extract at 600 nm enabled the determination of boron indirectly. The recommended procedure is as follows: Take an aliquot of the boron solution (2.0 x 10 - 4 mol l - 1 ) into a 10-ml test tube. Add 1 ml of carbonate buffer solution (pH 9.4) and 0.25 ml of crystal violet solution (1.0 x 10 - 2 mol l - 1 ), and dilute the mixed solution to 4 ml with deionized water. Shake the solution with 4 ml of benzene solution containing hydrobenzoin (2.0 x 10 - 2 mol l - 1 ) for 2 min. Measure the absorbance of the organic phase at 600 nm using a 10-mm glass cell against benzene. The calibration curve obeyed Beer's law on the concentration range from 2.5 x 10 - 6 mol l - 1 to 2.5 x 10 - 5 mol l - 1 of boron, and the apparent molar absorptivity was 3.0 x 10 4 l mol - 1 cm - 1 at 20 0 C. It was found that many kinds of co-existing ions interfered with the determination. However, this method was applicable to the determination of boron in sea water when chloride ion and cations such as Ca(II) and Mg(II) were previously eliminated by treating the sample solution with Ag 2 O and cation exchanger resin. The proposed method is a very simple and rapid one, because this method does not require apparatus other than common laboratories and the evaporation to dryness of sample or removal of the excess of reagent. (author)

ESR investigations of radiation grafting of methyl methacrylate in aqueous emulsion onto chrome-tanned pig skin

International Nuclear Information System (INIS)

Pietrucha, K.; Pekala, W.; Plonka, A.

1980-01-01

Upon γ-irradiation at 77 K of the aqueous emulsions of methyl methacrylate embedded into chrome-tanned pig skins there are formed only the radicals of collagen and of 2-el-2-methylopropionic acid methyl ester. The presence of water in the system increases markedly the radiation yield of collagen radicals. During gradual heating up the polymerization reactions start and the macro-radical of growing polymer is observed. Chromium does not participate in the processes of initiation and grafting. (author)

Hardening parts by chrome plating in manufacture and repair

Science.gov (United States)

Astanin, V. K.; Pukhov, E. V.; Stekolnikov, Y. A.; Emtsev, V. V.; Golikova, O. A.

2018-03-01

In the engineering industry, galvanic coatings are widely used to prolong the service life of the machines, which contribute to the increase in the strength of the parts and their resistance to environmental influences, temperature and pressure drops, wear and fretting corrosion. Galvanic coatings have been widely applied in engineering, including agriculture, aircraft building, mining, construction, and electronics. The article focuses on the manufacturing methods of new agricultural machinery parts and the repair techniques of worn parts by chrome plating. The main attention is paid to the unstable methods of chromium deposition (in pulsed and reversing modes) in low-concentration electrolytes, which makes it possible to increase the reliability and durability of the hardened parts operation by changing the conditions of electrocrystallization, that is, directed formation of the structure and texture, thickness, roughness and microhardness of chromium plating. The practical recommendations are given on the current and temperature regimes of chromium deposition and composition of baths used for the restoration and hardening of the machine parts. Moreover, the basic methods of machining allowances removal are analysed.

Comparative of the Tribological Performance of Hydraulic Cylinders Coated by the Process of Thermal Spray HVOF and Hard Chrome Plating

Directory of Open Access Journals (Sweden)

R.M. Castro

2014-03-01

Full Text Available Due to the necessity of obtaining a surface that is resistant to wear and oxidation, hydraulic cylinders are typically coated with hard chrome through the process of electroplating process. However, this type of coating shows an increase of the area to support sealing elements, which interferes directly in the lubrication of the rod, causing damage to the seal components and bringing oil leakage. Another disadvantage in using the electroplated hard chromium process is the presence of high level hexavalent chromium Cr+6 which is not only carcinogenic, but also extremely contaminating to the environment. Currently, the alternative process of high-speed thermal spraying (HVOF - High Velocity Oxy-Fuel, uses composite materials (metal-ceramic possessing low wear rates. Research has shown that some mechanical properties are changed positively with the thermal spray process in industrial applications. It is evident that a coating based on WC has upper characteristics as: wear resistance, low friction coefficient, with respect to hard chrome coatings. These characteristics were analyzed by optical microscopy, roughness measurements and wear test.

Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis.

Science.gov (United States)

Bañón, E; Marcilla, A; García, A N; Martínez, P; León, M

2016-02-01

The thermal decomposition of chrome tanned leather before and after a soaking treatment with NaOH was studied using thermogravimetric analysis (TGA). The effect of the solution concentration (0.2M and 0.5M) and the soaking time (5min and 15min) was evaluated. TGA experiments at four heating rates (5, 10, 15 and 20°Cmin(-1)) were run in a nitrogen atmosphere for every treatment condition. A kinetic model was developed considering the effect of the three variables studied, i.e.: the NaOH solution concentration, the soaking time and the heating rate. The proposed model for chrome tanned leather pyrolysis involves a set of four reactions, i.e.: three independent nth order reactions, yielding the corresponding products and one of them undergoing a successive cero order reaction. The model was successfully applied simultaneously to all the experimental data obtained. The evaluation of the kinetic parameters obtained (activation energy, pre-exponential factor and reaction order) allowed a better understanding of the effect of the alkali treatment on these wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Recycling of Chrome Tanned Leather Dust in Acrylonitrile Butadiene Rubber

Science.gov (United States)

El-Sabbagh, Salwa H.; Mohamed, Ola A.

2010-06-01

Concerns on environmental waste problem caused by chrome tanned leather wastes in huge amount have caused an increasing interest in developing this wastes in many composite formation. This leather dust was used as filler in acrylonitrile butadiene rubber (NBR) before treatment and after treatment with ammonia solution and sod. formate. Different formulations of NBR/ leather dust (untreated-treated with ammonia solution—treated with sod. formate) composites are prepared. The formed composite exhibit a considerable improvement in some of their properties such as rheometric characteristics especially with composites loaded with treated leather dust. Tensile strength, modulus at 100% elongation, hardness and youngs modulus were improved then by further loading start to be steady or decrease. Cross linking density in toluene were increased by incorporation of leather dust treated or untreated resulting in decreases in equilibrium swelling. Distinct increase in the ageing coefficient of both treated and untreated leather with drop in NBR vulcanizates without leather dust. Addition of leather dust treated or untreated exhibit better thermal stability.

Preparation of 2-acrylamido-2 methyl propane-1-sulfonic acid/bentonite composite by radiation polymerization for adsorption of basic violet dye from aqueous solution

International Nuclear Information System (INIS)

Sokker, H.H.; Younes, M.M.; Abdel-Kareem, M.; Zohdy, K.

2010-01-01

Water uptake and the sorption properties of composite made by radiation polymerization of 2-acrylamido-2- methyl propane -1-sulfonic acid (AMPS) and a clay such as bentonite were investigated as a function of composition (2,6 and 10% w.t %) of bentonite and radiation dose. The prepared composite was characterized by FTIR and SEM. Swelling experiments were performed in water at 25 degree C. The prepared composite was applied for adsorption of basic violet dye at different ph values and the results showed that the prepared composite of composition (10% wt % of bentonite) showed the highest removal percent of basic violet dye at ph=9 compared with other compositions. Also, the adsorption capacity of basic violet at ph 3,7 and 9 were 3.5, 9 and 50 mg/g, respectively. The adsorption process of basic violet follows both Freundlich and Langmuir models and followed pseudo second order kinetic model

Sensitive detection of malachite green and crystal violet by nonlinear laser wave mixing and capillary electrophoresis.

Science.gov (United States)

Maxwell, Eric J; Tong, William G

2016-05-01

An ultrasensitive label-free antibody-free detection method for malachite green and crystal violet is presented using nonlinear laser wave-mixing spectroscopy and capillary zone electrophoresis. Wave-mixing spectroscopy provides a sensitive absorption-based detection method for trace analytes. This is accomplished by forming dynamic gratings within a sample cell, which diffracts light to create a coherent laser-like signal beam with high optical efficiency and high signal-to-noise ratio. A cubic dependence on laser power and square dependence on analyte concentration make wave mixing sensitive enough to detect molecules in their native form without the use of fluorescent labels for signal enhancement. A 532 nm laser and a 635 nm laser were used for malachite green and crystal violet sample excitation. The use of two lasers of different wavelengths allows the method to simultaneously detect both analytes. Selectivity is obtained through the capillary zone electrophoresis separation, which results in characteristic migration times. Measurement in capillary zone electrophoresis resulted in a limit of detection of 6.9 × 10(-10)M (2.5 × 10(-19) mol) for crystal violet and 8.3 × 10(-11)M (3.0 × 10(-20) mol) for malachite green at S/N of 2. Copyright © 2016. Published by Elsevier B.V.

Synthesis of Cu Doped ZnO Nanostructures for Ultra Violet Sensing

OpenAIRE

Nazar Abbas SHAH; Muhammad ABID; Muhammad AMIN; Rahat AFRIN; Syed Zafar ILYAS

2015-01-01

This paper mainly focused on the synthesis of zinc oxide nanostructures, their characterization and their ultra violet light sensing response at room temperature. Nanowires, nanobelts and nanosheets were synthesized by varying doping material copper by using vapor transport technique governed by the vapor-liquid-solid or vapor-solid mechanisms. The structural, morphological and optical characterization was carried out using X-ray diffraction, scanning electron microscopy, energy dispersive X-...

Intense, stable and excitation wavelength-independent photoluminescence emission in the blue-violet region from phosphorene quantum dots

Science.gov (United States)

Ge, Shuaipeng; Zhang, Lisheng; Wang, Peijie; Fang, Yan

2016-01-01

Nanoscale phosphorene quantum dots (PQDs) with few-layer structures were fabricated by pulsed laser ablation of a bulk black phosphorus target in diethyl ether. An intense and stable photoluminescence (PL) emission of the PQDs in the blue-violet wavelength region is clearly observed for the first time, which is attributed to electronic transitions from the lowest unoccupied molecular orbital (LUMO) to the highest occupied molecular orbital (HOMO) and occupied molecular orbitals below the HOMO (H-1, H-2), respectively. Surprisingly, the PL emission peak positions of the PQDs are not red-shifted with progressively longer excitation wavelengths, which is in contrast to the cases of graphene and molybdenum disulphide quantum dots. This excitation wavelength-independence is derived from the saturated passivation on the periphery and surfaces of the PQDs by large numbers of electron-donating functional groups which cause the electron density on the PQDs to be dramatically increased and the band gap to be insensitive to the quantum size effect in the PQDs. This work suggests that PQDs with intense, stable and excitation wavelength-independent PL emission in the blue-violet region have a potential application as semiconductor-based blue-violet light irradiation sources. PMID:27265198

The influence of activating agents on the performance of rice husk-based carbon for sodium lauryl sulfate and chrome (Cr) metal adsorptions

Science.gov (United States)

Arneli; Safitri, Z. F.; Pangestika, A. W.; Fauziah, F.; Wahyuningrum, V. N.; Astuti, Y.

2017-02-01

This research aims to study the influence of activating agents to produce rice husk based-carbon with high adsorption capacity and efficiency for either hazardous organic molecules or heavy metals which are unfriendly for the environment. Firstly, rice husk was burned by pyrolysis at different temperatures to produce rice husk-based carbon. To improve its ability as an adsorbent, carbon was treated with activating agents, namely, H3PO4 and KOH at room and high temperature (420 °C). The performance of carbon was then tested by contacting it with surfactant (SLS). Finally, the surfactant-modified active carbon was applied for chrome metal removal. The result shows that activation of carbon using phosphate acid (H3PO4) was more effective than potassium hydroxide (KOH) conducted at high temperature to adsorb sodium lauryl sulfate (SLS) and chrome metal with the adsorption capacity 1.50 mgg-1 and 0.375 mgg-1, respectively.

Investigation of new dyes for chromovitrectomy: preclinical biocompatibility of trisodium, orangell and methyl violet.

Science.gov (United States)

Badaro, Emmerson; Souza-Lima, Rodrigo A; Novais, Eduardo A; Maia, Mauricio; Hirai, Flávio; Meyer, Carsten H; Farah, Michel Eid; Rodrigues, Eduardo B

2015-01-01

To investigate the retinal toxicity by electroretinography (ERG), clinical examination and histology after intravitreal injection of biological stains in two concentrations: Trisodium (0.50 g/L and 1.00 g/L), Orangell (0.25 g/L and 1.00 g/L) and Methyl Violet (0.50 g/L and 1.00 g/L). Eighteen New-Zealand albinos rabbits were assigned in six groups (n = 3 in each group). The animals in group 1 received Trisodium in the dose of 0.50 g/L and group 2 received 1.00 g/L; Group 3 received Orangell in the dose of 0.25 g/L and group 4 received 1.00 g/L; Group 5 received Methyl Violet in the dose of 1.00 g/L and group 6 received 0.50 g/L. A volume of 0.05 mL of dye was injected in the right eyes, whereas the left eyes received the same volume of balanced salt solution (BSS) as control. ERG recordings and clinical examination were performed at baseline and seven days after intravitreal injection. The ERG responses at one week after injection were compared with baseline levels. A decrease in the post-injection amplitude of more than 50% was considered remarkable. After the 7-day follow-up, rabbits were euthanized and eye enucleated for light microscopy (LM) histological evaluation. At clinical examination by indirect ophthalmoscopy seven days after dye injection, all eyes were negative for cataract, hemorrhage, retinal detachment, and intraocular opacities. Amplitude analysis of maximum scotopic b-wave showed no significant reduction in either dye injected or control eyes. Neither dye nor BSS caused significant retinal alteration on LM at doses tested. Trisodium, Orangell and Methyl Violet can be applied in future studies in order to prove the capacity to stain preretinal tissues and vitreous without toxicity. The three dyes did not induce significant ERG amplitude reduction or LM alterations in this preliminary experimental research. Trisodium, Orangell and Methyl Violet may be potentially useful vital dyes for ocular surgery, and deserve further

Flash photolysis of carbon dioxide in the far ultra-violet; Photolyse-eclair de l'anhydride carbonique dans l'ultra-violet lointain

Energy Technology Data Exchange (ETDEWEB)

Barat, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1970-07-01

The flash photolysis of CO{sub 2} (3 torr) in the far ultra-violet, down to the transparency limit of lithium fluoride, produces vibrationally excited CO in its {chi}{sup 1}{sigma} electronic ground state and an electronically excited oxygen atom O({sup 1}D). After photolysis, the changes in the concentration of vibrationally de-excited CO in the 0 to 200 {mu}sec, time range are followed using absorption spectroscopy. These changes can be explained on the basis of three main competing reactions: CO({chi}{sup 1}{sigma}, {nu}'' = 0) + O({sup 1}D) {yields} CO{sub 2}({sup 1}{sigma}{sub g}{sup +}), O({sup 1}D) + CO{sub 2} {yields} O({sup 3}P) + CO{sub 2} and CO{sub 3}, CO(X{sup 1}{sigma}, {nu}'' = 1,2) + CO{sub 2} {yields} CO({chi}{sup 1}{sigma}, {nu}'' = 0) + CO{sub 2}. The values of the rate constants for these three reactions are determined by analog calculations. The effect of O({sup 1}D) scavenging or quenching gases on the oxidation reaction of CO by O({sup 1}D) is examined. A study of the flash photolysis of O{sub 2} in the presence of CO in the far ultra-violet makes it possible to eliminate the hypothesis that CO{sub 3} is involved in the reaction leading to the disappearance of CO after photolysis. (author) [French] La photolyse eclair de CO{sub 2} (3 torrs) dans l'ultraviolet lointain, jusqu'a la limite de transparence du fluorure de lithium, produit CO vibrationnellement excite dans son etat electronique fondamental X et un atome d'oxygene electroniquement excite O({sup 1}D). Apres photolyse, on suit par spectroscopie d'absorption l'evolution de la concentration de CO vibrationnellement desexcite dans la gamme de temps s'etendant de 0 a 200 {mu}s. Cette evolution s'explique en admettant trois reactions concurrentes principales: CO({chi}{sup 1}{sigma}, {nu}'' = 0) + O({sup 1}D) {yields} CO{sub 2}({sup 1}{sigma}{sub g}{sup +}), O({sup 1}D) + CO{sub 2} {yields} O({sup 3}P) + CO{sub 2} et CO{sub 3}, CO(X{sup 1}{sigma}, {nu}'' = 1,2) + CO{sub 2} {yields} CO

Recursos de información elaborados por el CRAI. Instalar y Configurar Zotero enlazarlo a Mozilla, Chrome y Word

OpenAIRE

López Lucas, Jesús

2018-01-01

Este tutorial explica los pasos para la instalación del gestor de referencias bibliográficas Zotero en un PC con Sistema Operativo Microsoft Windows. Asimismo, se indican las características del software y la manera de trabajar con él desde Mozilla Firefox, Google Chrome y Microsoft Word. Tutorial sobre instalación y configuración de Zotero para los diferentes navegadores web.

Temperature sensitive molecularly imprinted microspheres for solid-phase dispersion extraction of malachite green, crystal violet and their leuko metabolites

International Nuclear Information System (INIS)

Tan, Lei; Chen, Kuncai; He, Rong; Peng, Rongfei; Huang, Cong

2016-01-01

This article demonstrates the feasibility of an alternative strategy for producing temperature sensitive molecularly imprinted microspheres (MIMs) for solid-phase dispersion extraction of malachite green, crystal violet and their leuko metabolites. Thermo-sensitive MIMs can change their structure following temperature stimulation. This allows capture and release of target molecules to be controlled by temperature. The fabrication technique provides surface molecular imprinting in acetonitrile using vinyl modified silica microspheres as solid supports, methacrylic acid and N-isopropyl acrylamide as the functional monomers, ethyleneglycol dimethacrylate as the cross-linker, and malachite green as the template. After elution of the template, the MIMs can be used for fairly group-selective solid phase dispersion extraction of malachite green, crystal violet, leucomalachite green, and leucocrystal violet from homogenized fish samples at a certain temperature. Following centrifugal separation of the microspheres, the analytes were eluted with a 95:5 mixture of acetonitrile and formic acid, and then quantified by ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) with isotope internal calibration. The detection limits for malachite green, crystal violet and their metabolites typically are 30 ng·kg −1 . Positive samples were identified by UHPLC-MS/MS in the positive ionization mode with multiple reaction monitoring. The method was applied to the determination of the dyes and the respective leuko dyes in fish samples, and accuracy and precision were validated by comparative analysis of the samples by using aluminum neutral columns. (author)

The Swift Ultra-Violet/Optical Telescope

International Nuclear Information System (INIS)

Roming, Peter; Hunsberger, S.D.; Nousek, John; Mason, Keith

2001-01-01

The Ultra-Violet/Optical Telescope (UVOT) provides the Swift Gamma-Ray Burst Explorer with the capability of quickly detecting and characterizing the optical and ultraviolet properties of gamma ray burst counterparts. The UVOT design is based on the design of the Optical Monitor on XMM-Newton. It is a Ritchey-Chretien telescope with microchannel plate intensified charged-coupled devices (MICs) that deliver sub-arcsecond imaging. These MICs are photon-counting devices, capable of detecting low intensity signal levels. When flown above the atmosphere, the UVOT will have the sensitivity of a 4m ground based telescope, attaining a limiting magnitude of 24 for a 1000 second observation in the white light filter. A rotating filter wheel allows sensitive photometry in six bands spanning the UV and visible, which will provide photometric redshifts of objects in the 1-3.5z range. For bright counterparts, such as the 9th magnitude GRB990123, or for fainter objects down to 17th magnitude, two grisms provide low-resolution spectroscopy

Evaluation of dynamics and equilibrium models for the sorption of Basic Violet 3 on activated carbon prepared from Moringa Oleifera fruit shell waste

Directory of Open Access Journals (Sweden)

C. Sumithra

2014-03-01

Full Text Available The feasibility of activated carbon prepared from Moringa oleifera fruit shell waste to remove Basic Violet 3 from aqueous solution was investigated through batch mode contact time studies. The surface chemistry of activated carbon is studied using Boehm titrations and pH of PZC measurements indicates that the surface oxygenated groups are mainly basic in nature. The surface area of the activated carbon is determined using BET method. The kinetics of Basic Violet 3 adsorption are observed to be pH dependent. The experimental data can be explained by Pseudo second order kinetic model. For, Basic Violet 3, the Langmuir model is best suited to stimulate the adsorption isotherms.

A review of the chrome mordant dyeing of wool with special reference to the afterchrome process

CSIR Research Space (South Africa)

Maasdorp, APB

1983-11-01

Full Text Available a -~min*o'- Hydroxyaw Dycs Salicylic Acid Dyes Azo dyes oxidkd to Quinone form when complexed (C.I. Mordant Black 3) e Chrome Fast Brow TV (C.I. Mordant Brow 33) Flavine A (C.I. Mordant Yellow 5) e Solochrome Rcd (C.I. Mordant..., it was decided that they should bedescribed in more detail. In 1858, Peter Greiss, a chemist at a Burton-on-Trent brewery produced the first diizonium salts by treating primary aromatic amines with nitrous acid produced from hydrochloric acid and sodium...

Monitoring the intensity of mechanical vibration during the processing of chrome steel 14109

Directory of Open Access Journals (Sweden)

Š. Salokyová

2017-01-01

Full Text Available Article deals with the examination of the effect of cutting parameters on the occurrence and size of mechanical vibration on three selected measured points during the processing of chrome steel. It also includes execution, experiment evaluation in this field and comparison of measured vibrations acceleration amplitude values according to the standards. The results of the measurement serve for early identification of a defect, which has great effect on the smoothness and efficiency of the machine. The article concludes with the proposed new findings from the measured values evaluation and formulated new recommendations for the operation in production system with lathe turning technology. The measured experimental values of the acceleration amplitude of mechanical vibrations were compared with theoretical values.

75 FR 29719 - Carbazole Violet Pigment 23 From India: Continuation of Countervailing Duty Order

Science.gov (United States)

2010-05-27

..., paste, wet cake) and finished pigment in the form of presscake and dry color. Pigment dispersions in any... DEPARTMENT OF COMMERCE International Trade Administration [C-533-839] Carbazole Violet Pigment 23... Pigment 23 From India, 69 FR 77995 (December 29, 2004). On November 2, 2009, the Department initiated and...

Fluorescence, Decay Time, and Structural Change of Laser Dye Cresyl Violet in Solution due to Microwave Irradiation at GSM 900/1800 Mobile Phone Frequencies

Directory of Open Access Journals (Sweden)

Fuat Bayrakceken

2012-01-01

Full Text Available Microwave irradiation at GSM 900/1800 MHz mobile phone frequencies affects the electronic structure of cresyl violet in solution. These changes are important because laser-dye cresyl violet strongly bonds to DNA- and RNA-rich cell compounds in nerve tissues. The irradiation effects on the electronic structure of cresyl violet and its fluorescence data were all obtained experimentally at room temperature. For most laser dyes, this is not a trivial task because laser dye molecules possess a relatively complex structure. They usually consist of an extended system of conjugated double or aromatic π-bonds with attached auxochromic (electron donating groups shifting the absorption band further towards longer wavelength. Because of the intrinsically high degree of conjugation, the vibrational modes of the molecular units couple strongly with each other. We found that the fluorescence quantum yield was increased from to due to intramolecular energy hopping of cresyl violet in solution which is exposed to microwave irradiation at mobile phone frequencies, and the photonic product cannot be used as a laser dye anymore.

Differential inheritance of pepper (capsicum annum) fruit pigments results in black to violet fruit color

Science.gov (United States)

Color and appearance of fruits and vegetables are critical determinants of product quality and may afford high-value market opportunities. Exploiting the rich genetic diversity in Capsicum, we characterized the inheritance of black and violet immature fruit color and chlorophyll, carotenoid and ant...

Incapacity of β - carotene to protect Escherichia coli J-5 against ultra violet lethal action

International Nuclear Information System (INIS)

Passos Junior, G.A.S.; Zucchi, T.M.A.D.

1982-01-01

The ultra violet light survival of Escherichia coli J-5 cell population was not modified when it was β-carotene treated. It was found that this carotenoid does not confer radioprotection to the u.v. light effects in this bacterial strain. (author) [pt

Selection and application of C18200 chrome copper for the OHTE confinement test helical coil

International Nuclear Information System (INIS)

Puhn, F.A.; Graumann, D.W.

1981-01-01

The selection and qualification of copper for the OHTE confinement test helical coil (H-coil) was a crucial step in the success of this new experiment. Previous problems encountered at General Atomic Company with close tolerance machined parts made from high strength copper were identified. The design criteria included selecting a material with minimal warpage during machining, an electrical conductivity >80% IACS, and a yield strength of at least 241 Mpa (35 ksi). The investigation of candidate materials and testing samples led to selection of a material that fully met all requirements. The C18200 chrome copper forged plates were supplied by the Ampco Metal Division of Ampco-Pittsburgh Corporation

Nucleotide sequence and genetic organization of Hungarian grapevine chrome mosaic nepovirus RNA2.

Science.gov (United States)

Brault, V; Hibrand, L; Candresse, T; Le Gall, O; Dunez, J

1989-10-11

The complete nucleotide sequence of hungarian grapevine chrome mosaic nepovirus (GCMV) RNA2 has been determined. The RNA sequence is 4441 nucleotides in length, excluding the poly(A) tail. A polyprotein of 1324 amino acids with a calculated molecular weight of 146 kDa is encoded in a single long open reading frame extending from nucleotides 218 to 4190. This polyprotein is homologous with the protein encoded by the S strain of tomato black ring virus (TBRV) RNA2, the only other nepovirus sequenced so far. Direct sequencing of the viral coat protein and in vitro translation of transcripts derived from cDNA sequences demonstrate that, as for comoviruses, the coat protein is located at the carboxy terminus of the polyprotein. A model for the expression of GCMV RNA2 is presented.

Isolation and Characterization of Paracoccus sp. GSM2 Capable of Degrading Textile Azo Dye Reactive Violet 5

Directory of Open Access Journals (Sweden)

Mallikarjun C. Bheemaraddi

2014-01-01

Full Text Available A potential bacterial strain GSM2, capable of degrading an azo dye Reactive Violet 5 as a sole source of carbon, was isolated from textile mill effluent from Solapur, India. The 16S rDNA sequence and phenotypic characteristics indicated an isolated organism as Paracoccus sp. GSM2. This strain exhibited complete decolorization of Reactive Violet 5 (100 mg/L within 16 h, while maximally it could decolorize 800 mg/L of dye within 38 h with 73% decolorization under static condition. For color removal, the most suitable pH and temperature were pH 6.0–9.0 and 25–40°C, respectively. The isolate was able to decolorize more than 70% of five structurally different azo dyes within 38 h. The isolate is salt tolerant as it can bring out more than 90% decolorization up to a salt concentration of 2% (w/v. UV-Visible absorption spectra before and after decolorization suggested that decolorization was due to biodegradation and was further confirmed by FT-IR spectroscopy. Overall results indicate the effectiveness of the strain GSM2 explored for the treatment of textile industry effluents containing various azo dyes. To our knowledge, this could be the first report on biodegradation of Reactive Violet 5 by Paracoccus sp. GSM2.

Effects of epigallocatechin gallate on ultra-violet-induced cell death in PC12 cells

International Nuclear Information System (INIS)

Takahashi, Hideo; Seki, Sakiko; Sakamoto, Naotaka; Nakagawa, Shigeki

2002-01-01

We examined the effects of catechin on ultra-violet-induced cell death in PC12 cells. PC12 cells were irradiated by ultra-violet C (254 nm) (UVC). We found that the lactate dehydrogenase (LDH) activities in culture media and lipid peroxide in PC12 cells, which indicate cell death and cell membrane damage, respectively, were increased by UVC irradiation in a time-dependent manner. Cell death was gradually stimulated for 9 hours of cultivation after a UVC irradiation period of 10 or 30 min. Epigallocatechin gallate (EGCG), which is one of the main catechins found in green tea, suppressed the increase in LDH activity in culture medium and also inhibited the formation of lipid peroxide. IκB, a member of the cell death signaling system, was phosphorylated at 1 hour after 10 min of UVC irradiation. Stimulation of phosphorylation of IκB by UVC was suppressed by the addition of EGCG. We concluded that EGCG protects the PC12 cell from cell damage caused by UVC irradiation. (author)

Source of the violet depression in carbon stars (a study of the Balmer decrement in carbon L.P.V.s)

International Nuclear Information System (INIS)

Orlati, M.A.

1985-01-01

In an effort to determine the nature of the agent(s) of the violet depression in N-type stars through the behavior of their Balmer decrement, slit spectrograms of two C, one CS, two S (all reported to have the violet depression) and one M type LPVs were repeatedly taken between May 1983 and November 1984. The observed phase related changes in the Balmer decrement exclude the possibility that the absorbers are circumstellar because the emission region in the best-observed star is seen to rise through the opacity source. The exact nature and number of kinds of absorbers remains to be determined

A novel RE-chrome-boronizing technology assisted by fast multiple rotation rolling treatment at low temperature

Energy Technology Data Exchange (ETDEWEB)

Yuan, Xing-dong [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China); Xu, Bin, E-mail: xubin@sdjzu.edu.cn [School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China); Cai, Yu-cheng [School of Materials Science and Engineering, Shandong Jianzhu University, Jinan 250101 (China)

2015-12-01

Highlights: • A nanostructured layer with grain size of approximately 30 nm was successfully fabricated in the upper-layer of carbon steel. • The penetrating rate was enhanced significantly by the fast multiple rotation rolling (FMRR) treatment at low temperature. • A novel and efficient RE-Chrome-Boronizing technology assisted by fast multiple rotation rolling (FMRR) treatment at low temperature was used to fabricate boride layers on the surface of carbon steel. - Abstract: The boride layer was fabricated on the surface of carbon steel by a novel RE-Chrome-Boronizing technology assisted by fast multiple rotation rolling (FMRR) treatment at low temperature. The microstructure of the boride layer was characterized by using scanning electron microscopy (SEM). The microstructure of the top surface layer of substrate was characterized by transmission electron microscopy (TEM) and high resolution rransmission electron microscopy (HRTEM). Experimental results showed that a nanostructured layer with grain size of approximately 30 nm was obtained; the amorphous phase and high-density dislocations were observed in upper-layer of FMRR samples, which led to the reduction of diffusion activation energy of boron atoms. Boride layers fabricated on the FMRR samples are continuous, dense, uniform, and low in brittleness. The penetrating rate was enhanced significantly when the FMRR samples were Cr-Rare earth-boronized at 650 °C for 6 h. The thickness of the boride layer of FMRR samples on carbon steel was approximately 25 μm when the duration was 60 min, which was approximately 1.5 times higher than the original sample. The boride layer consisted of mainly Fe2B, and adheres well to the metallic substrate.

One electron reduction and absorption characteristics of Cresyl violet in micellar medium

International Nuclear Information System (INIS)

Gawandi, Vijay B.; Guha, S.N.; Hari Mohan

2000-01-01

Effect of surfactant micelles on absorption characteristics of Cresyl violet (CV) and on its redox reactions have been studied. Among the various surfactants investigated anionic surfactants particularly sodium lauryl sulfate (SLS) and sodium dodecyl benzene sulfonate (SDDBS) showed marked effect on these properties. Reactions of hydrated electron in these micellar media were studied using the technique of nanosecond pulse radiolysis. Results of other surfactants, viz.BSS, CTAB and TritonX-100 have also been presented. (author)

Timing of Secondary Hydrothermal Alteration of the Luobusa Chromitites Constrained by Ar/Ar Dating of Chrome Chlorites

Directory of Open Access Journals (Sweden)

Wei Guo

2018-05-01

Full Text Available Chrome chlorites are usually found as secondary phases formed by hydrothermal alteration of chromite deposits and associated mafic/ultramafic rocks. Here, we report the 40Ar/39Ar age of chrome chlorites separated from the Luobusa massive chromitites which have undergone secondary alteration by CO2-rich hydrothermal fluids. The dating results reveal that the intermediate heating steps (from 4 to 10 of sample L7 generate an age plateau of 29.88 ± 0.42 Ma (MSWD = 0.12, plateau 39Ar = 74.6%, and the plateau data points define a concordant inverse isochron age of 30.15 ± 1.05 Ma (MSWD = 0.08, initial 40Ar/36Ar = 295.8 ± 9.7. The Ar release pattern shows no evidence of later degassing or inherited radiogenic component indicated by an atmospheric intercept, thus representing the age of the hydrothermal activity. Based on the agreement of this hydrothermal age with the ~30 Ma adakitic plutons exposed in nearby regions (the Zedong area, tens of kilometers west Luobusa and the extensive late Oligocene plutonism distributed along the southeastern Gangdese magmatic belt, it is suggested that the hydrothermal fluids are likely related to the ~30 Ma magmatism. The hydrothermal fluid circulation could be launched either by remote plutons (such as the Sangri granodiorite, the nearest ~30 Ma pluton west Luobusa or by a similar coeval pluton in the local Luobusa area (inferred, not found or reported so far. Our results provide important clues for when the listwanites in Luobusa were formed.

[Qualitative Determination of Organic Vapour Using Violet and Visible Spectrum].

Science.gov (United States)

Jiang, Bo; Hu, Wen-zhong; Liu, Chang-jian; Zheng, Wei; Qi, Xiao-hui; Jiang, Ai-li; Wang, Yan-ying

2015-12-01

Vapours of organic matters were determined qualitatively employed with ultraviolet-visible absorption spectroscopy. Vapours of organic matters were detected using ultraviolet-visible spectrophotometer employing polyethylene film as medium, the ultraviolet and visible absorption spectra of vegetable oil vapours of soybean oil, sunflower seed oil, peanut oil, rapeseed oil, sesame oil, cotton seed oil, tung tree seed oil, and organic compound vapours of acetone, ethyl acetate, 95% ethanol, glacial acetic acid were obtained. Experimental results showed that spectra of the vegetable oil vapour and the organic compound vapour could be obtained commendably, since ultra violet and visible spectrum of polyethylene film could be deducted by spectrograph zero setting. Different kinds of vegetable oils could been distinguished commendably in the spectra since the λ(max), λ(min), number of absorption peak, position, inflection point in the ultra violet and visible spectra obtained from the vapours of the vegetable oils were all inconsistent, and the vapours of organic compounds were also determined perfectly. The method had a good reproducibility, the ultraviolet and visible absorption spectra of the vapours of sunflower seed oil in 10 times determination were absolutely the same. The experimental result indicated that polyethylene film as a kind of medium could be used for qualitative analysis of ultraviolet and visible absorption spectroscopy. The method for determination of the vapours of the vegetable oils and organic compounds had the peculiarities of fast speed analysis, well reproducibility, accuracy and reliability and low cost, and so on. Ultraviolet and visible absorption spectrum of organic vapour could provide feature information of material vapour and structural information of organic compound, and provide a novel test method for identifying vapour of compound and organic matter.

Ultra violet photoemission studies of CO2 and NO adsorbed on W(100) surface

International Nuclear Information System (INIS)

Bhattacharya, A.K.; Broughton, J.Q.; Perry, D.L.

1978-01-01

In the last few years ultra violet photoelectron spectroscopy (UPS) has been successfully empolyed to determine the nature and bonding of the species formed when gases absorb on metal surfaces. This information is necessary to understand the mechanism of hetergeneous catalysis. The present report deals with UPS investigation of the chemisorption of CO 2 and NO on a W(100) surface. (Auth.)

Ultra-violet radiation is responsible for the differences in global epidemiology of chickenpox and the evolution of varicella-zoster virus as man migrated out of Africa.

Science.gov (United States)

Rice, Philip S

2011-04-23

Of the eight human herpes viruses, varicella-zoster virus, which causes chickenpox and zoster, has a unique epidemiology. Primary infection is much less common in children in the tropics compared with temperate areas. This results in increased adult susceptibility causing outbreaks, for example in health-care workers migrating from tropical to temperate countries. The recent demonstration that there are different genotypes of varicella-zoster virus and their geographic segregation into tropical and temperate areas suggests a distinct, yet previously unconsidered climatic factor may be responsible for both the clinical and molecular epidemiological features of this virus infection. Unlike other human herpes viruses, varicella-zoster virus does not require intimate contact for infection to occur indicating that transmission may be interrupted by a geographically restricted climatic factor. The factor with the largest difference between tropical and temperate zones is ultra-violet radiation. This could reduce the infectiousness of chickenpox cases by inactivating virus in vesicles, before or after rupture. This would explain decreased transmissibility in the tropics and why the peak chickenpox incidence in temperate zones occurs during winter and spring, when ultra-violet radiation is at its lowest. The evolution of geographically restricted genotypes is also explained by ultra-violet radiation driving natural selection of different virus genotypes with varying degrees of resistance to inactivation, tropical genotypes being the most resistant. Consequently, temperate viruses should be more sensitive to its effects. This is supported by the observation that temperate genotypes are found in the tropics only in specific circumstances, namely where ultra-violet radiation has either been excluded or significantly reduced in intensity. The hypothesis is testable by exposing different virus genotypes to ultra-violet radiation and quantifying virus survival by plaque forming

The creation of radiation dominated plasmas using laboratory extreme ultra-violet lasers

Science.gov (United States)

Tallents, G. J.; Wilson, S.; West, A.; Aslanyan, V.; Lolley, J.; Rossall, A. K.

2017-06-01

Ionization in experiments where solid targets are irradiated by high irradiance extreme ultra-violet (EUV) lasers is examined. Free electron degeneracy effects on ionization in the presence of a high EUV flux of radiation is shown to be important. Overlap of the physics of such plasmas with plasma material under compression in indirect inertial fusion is explored. The design of the focusing optics needed to achieve high irradiance (up to 1014 Wcm-2) using an EUV capillary laser is presented.

75 FR 62765 - Carbazole Violet Pigment 23 From India: Final Results of Antidumping Duty Changed-Circumstances...

Science.gov (United States)

2010-10-13

... finished pigment in the form of presscake and dry color. Pigment dispersions in any form (e.g., pigment... DEPARTMENT OF COMMERCE International Trade Administration [A-533-838] Carbazole Violet Pigment 23... Act), that Meghmani Pigments is the successor-in-interest to Alpanil Industries. DATES: Effective Date...

Studies on adsorption of crystal violet dye from aqueous solution onto coniferous pinus bark powder (CPBP)

International Nuclear Information System (INIS)

Ahmad, Rais

2009-01-01

The present study shows that the coniferous pinus bark powder (CPBP) can be used as a potential adsorbent for the removal of crystal violet (basic dye) from aqueous solutions. Experiments were carried out as a function of contact time, concentration, temperature, pH and dosage. The amount of dye uptake was found to vary with increasing initial solution pH and maximum adsorption was observed at pH 8. The equilibrium was attained in 2 h. The amount of dye uptake (mg/g) was found to increase with increase in dye concentration and contact time. The % adsorption was found to decrease with increase in amount of adsorbent. The thermodynamic parameters were also calculated and the positive value of ΔH o indicates the endothermic nature of adsorption. The applicability of the three isotherm's model for the present data follows the order: Langmuir > Temkin > Freundlich. The kinetics of crystal violet on to the adsorbent can be described well by pseudo-second order > Elovich > pseudo-first order equation.

Adsorption of methyl violet from aqueous solution using gum xanthan/Fe3O4 based nanocomposite hydrogel

CSIR Research Space (South Africa)

Mittal, H

2016-08-01

Full Text Available This research paper reports the utilization of gum xanthan-grafted-polyacrylic acid and Fe(sub3)O(sub4) magnetic nanoparticles based nanocomposite hydrogel (NCH) for the highly effective adsorption of methyl violet (MV) from aqueous solution...

Studies on tempering at different temperatures of the beta phase retained by water quenching in uranium-chromium alloys containing from 0,37 to 4 atoms of chromium percent (1963); Etude du revenu a differentes temperatures de la phase beta retenue par trempe a l'eau dans les alliages uranium-chrome contenant de 0,37 a 4 atomes pour cent de chrome (1963)

Energy Technology Data Exchange (ETDEWEB)

Degois, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-15

The author made a systematic study of the annealing of the beta phase retained by water-quenching in uranium-chromium alloys of concentrations between 0.37 and 4 of chromium percent. It is shown that alloys containing less than 1 atom per cent are transformed at temperatures between room temperature and 250 deg. C according to a bainitic process involving activation energies of the order of 14,500 cal/mole. Alloys containing more than 1 at. per cent are transformed at temperature between 400 and 650 deg. C by way of a germination and growth process involving an activation energy of the order of 33,000 cal/mole. The limit of solubility of chromium in beta uranium plays a fundamental part in the transformations of the alloys. The TTT curves of beta {yields} alpha transformation were drawn by the use of a thermo-dilatometer of very low inertia. The transformation law may be expressed 1 x = exp. (kt){sup n}; x represents the degree of progression of the transformation, k a coefficient dependent on the temperature, and n an exponent depending only on the composition of the alloy. A micrographic and crystallographic study confirmed the results found by dilatometry; in particular it was possible to measure the progression rates of the transformation. (author) [French] L'auteur a fait une etude systematique du revenu de la phase beta retenue par trempe a l'eau dans les alliages uranium-chrome de teneurs comprises entre 0,37 et 4 atomes pour cent de chrome. Il a montre que les alliages qui contiennent moins de 1 atome pour cent de chrome se transforment aux temperatures comprises entre la temperature ordinaire et 250 deg. C selon un processus bainitique mettant en jeu des energies d'activatlon de l'ordre de 14500 cal/mole. Les alliages qui renferment plus de 1 atome pour cent de chrome se transforment aux temperatures comprises entre 400 et 650 deg. C suivant un processus de germination et croissance mettant en jeu une energie d'activation de l'ordre de -33000 cal/mole. La

Therapeutic response of West African Dwarf goats infected with Peste des Petits Ruminants whose oral lesions were treated with oxytetracycline long acting and gentian violet topical spray

Directory of Open Access Journals (Sweden)

Iniobong Chukwuebuka Ikenna Ugochukwu

2017-11-01

Full Text Available Objective: To assess the therapeutic response of West African Dwarf (WAD goats infected with Peste des Petits Ruminants (PPR virus treated with Amantidine hydrochloride. Methods: Apart from the presence of the characteristic clinical signs, complement ELISA and haemagglutination inhibition (HI tests were used to confirm PPR infection in the WAD goats. The oral lesions in one group were cleaned with 70% alcohol and treated with oxytetracycline long acting (LA intramuscularly (IM and topically treated with gentian violet spray which also contained oxytetracycline, and in another group WAD goats infected with PPR virus were only treated with oxytetracycline LA intramuscularly. Results: The oral lesions in the group cleaned with 70% alcohol, treated with oxyteteracycline LA intramuscularly and gentian violet spray which also contained oxytetracycline topically healed appreciably within 3 weeks before the termination of the experiment, while the group that was treated with oxyteteracycline LA intramuscularly only healed poorly. The mortality of the WAD goats with PPR whose oral lesions were not treated with gentian violet topical spray was 100%, while the mortality of WAD goats treated with oxytetracycline LA intramuscularly and gentian violet topical spray was 71.42%. Conclusions: The results of this present study suggest that in addition to antiviral therapy, cleaning with 70% alcohol, combination of oxytetracycline LA and topical spraying of the oral lesions with gentian violet spray which also contains oxytetracycline reduced the morbidity and mortality considerably.

Plications of extended ultra-violet circular dichroism spectroscopy in biology and medicine.

Science.gov (United States)

Jones, Gareth R; Clarke, David T

2004-01-01

Deep ultra-violet circular dichroism is fast becoming an important technique in structural biology. The exponential increase in the number of protein structures deposited in the Protein Data Bank together with programs that extract protein secondary structure from atomic coordinates and the advancement of the software to analyse circular dichroic spectra, have revolutionised the technique. In addition, the extended short wavelength data afforded by synchrotron radiation is set to have a major impact on the development of the area. We have selected three diverse areas of research and development in the biomedical sciences to illustrate the ubiquity of the technique for future applications in the area of biomedical research. For example, the high flux of synchrotron radiation has provided a gold standard for the assay of the lipoprotein HDL in serum which has been proven to reverse the effects of coronary heart disease. In a second example, the high flux of synchrotron radiation enables the recording of millisecond data during the conformational changes in proteins over their spectrum, mapping out changes to protein secondary structure and thus providing absolute structural measurements in the millisecond time regime. In the third example, subtle conformational changes are interpreted from the extended CD spectra on protein drug binding, distinguishing between induced binding effects and the conformational changes in the target protein. The strengths and weaknesses of extended ultra-violet circular dichroism using synchrotron radiation are discussed using these examples as a template.

75 FR 36630 - Carbazole Violet Pigment 23 from the People's Republic of China: Final Results of Antidumping...

Science.gov (United States)

2010-06-28

... from the People's Republic of China: Final Results of Antidumping Duty Administrative Review AGENCY... the People's Republic of China (PRC). See Carbazole Violet Pigment 23 From the People's Republic of... (December 29, 2009) (Preliminary Results). This administrative review covers one exporter of the subject...

Parallel between steels alloyed with chrome-nickel and Fe-Mn-Al-C steels, in their response to fracture and wear (Review)

International Nuclear Information System (INIS)

Ramos, J; Perez, G.A

2008-01-01

The big worldwide demand for chrome-nickel alloy steels ('conventional steel') leads to the need for advanced materials for applications in different engineering systems that operate at high temperatures and in aggressive environmental conditions, favoring research and development in alternate alloys. In this technological race in search of these new materials, the FeMnAlC alloys ('new steels') have attracted attention for their excellent mechanical and tribological properties as well as for their good performance in corrosive-oxide environments, which make them similar to conventional steel. There are two important similarities between these two steels. First, an agent that causes the passive film to become stainless appears in both steels: chrome in the conventional steel, and aluminum in the FeMnAl alloy. The second similarity is that a stabilizing agent of the austenitic phase (FCC) appears in both, so that excellent mechanical properties can be obtained: nickel in the conventional steel, and manganese in the FeMnAl alloy. In certain sectors, such as aeronautics, conventional steel is rarely used because it is a very heavy material. This conventional steel is almost three times heavier that aluminum (7.85/2.7). Two advantages that the new FeMnAIC steels have compared to the conventional steels are that they are about 13% lighter in weight and they are less expensive. The FeMnAl also have excellent mechanical properties and good corrosion-oxidation resistance, which generates big expectations for their application in a broad scientific spectrum. This work reports the state of the information currently available about FeMnAlC alloys, comparing the mechanical and tribological behaviors of conventional alloy steels with chrome and nickel alloys, specifying the scopes of their application. A condition that favors the steels' fragility is the high speed of deformation and impact, where the FCC crystalline structure materials do not have a fragile ductile transition

Establishment of Wear Resistant HVOF Coatings for 50CrMo4 Chromium Molybdenum Alloy Steel as an Alternative for Hard Chrome Plating

Science.gov (United States)

Karuppasamy, S.; Sivan, V.; Natarajan, S.; Kumaresh Babu, S. P.; Duraiselvam, M.; Dhanuskodi, R.

2018-05-01

High cost imported components of seamless steel tube manufacturing plants wear frequently and need replacement to ensure the quality of the product. Hard chrome plating, which is time consuming and hazardous, is conventionally used to restore the original dimension of the worn-out surface of the machine components. High Velocity Oxy-Fuel (HVOF) thermal spray coatings with NiCrBSi super alloy powder and Cr3C2 NiCr75/25 alloy powder applied on a 50CrMo4 (DIN-1.7228) chromium molybdenum alloy steel, the material of the wear prone machine component, were evaluated for use as an alternative for hard chrome plating in this present work. The coating characteristics are evaluated using abrasive wear test, sliding wear test and microscopic analysis, hardness test, etc. The study results revealed that the HVOF based NiCrBSi and Cr3C2NiCr75/25 coatings have hardness in the range of 800-900 HV0.3, sliding wear rate in the range of 50-60 µm and surface finish around 5 microns. Cr3C2 NiCr75/25 coating is observed to be a better option out of the two coatings evaluated for the selected application.

HPLC Determination and MS Confirmation of Malachite Green, Gentian Violet, and Their Leuco Metabolites in Catfish Muscle

Science.gov (United States)

Residues of malachite green (MG), gentian violet (GV), and their leuco metabolites in catfish muscle were individually determined by HPLC using visible and fluorescence detectors. This detection scheme obviated a PbO2 column that converts leuco forms to chromatic forms for visible detection, thus el...

Nanoscale investigation of the degradation mechanism of a historical chrome yellow paint by quantitative electron energy loss spectroscopy mapping of chromium species.

Science.gov (United States)

Tan, Haiyan; Tian, He; Verbeeck, Jo; Monico, Letizia; Janssens, Koen; Van Tendeloo, Gustaaf

2013-10-18

Getting the picture: The investigation of 100 year old chrome yellow paint by transmission electron microscopy and spectroscopy has led to the identification of four types of core-shell particles. This nanoscale investigation has allowed a mechanism to be proposed for the darkening of some bright yellow colors in Van Gogh's paintings (e.g. in Falling leaves (Les Alyscamps), 1888). Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The relationship between the violet pigment PP-V production and intracellular ammonium level in Penicillium purpurogenum.

Science.gov (United States)

Kojima, Ryo; Arai, Teppei; Matsufuji, Hiroshi; Kasumi, Takafumi; Watanabe, Taisuke; Ogihara, Jun

2016-12-01

Penicillium purpurogenum is the fungus that produces an azaphilone pigment. However, details about the pigment biosynthesis pathway are unknown. The violet pigment PP-V is the one of the main pigments biosynthesized by this fungus. This pigment contains an amino group in a pyran ring as its core structure. We focused on this pigment and examined the relationship between intracellular ammonium concentration and pigment production using glutamine as a nitrogen source. The intracellular ammonium level decreased about 1.5-fold in conditions favoring PP-V production. Moreover, P. purpurogenum was transferred to medium in which it commonly produces the related pigment PP-O after cultivating it in the presence or absence of glutamine to investigate whether this fungus biosynthesizes PP-V using surplus ammonium in cells. Only mycelia cultured in medium containing 10 mM glutamine produced the violet pigment, and simultaneously intracellular ammonium levels decreased under this condition. From comparisons of the amount of PP-V that was secreted with quantity of surplus intracellular ammonium, it is suggested that P. purpurogenum maintains ammonium homeostasis by excreting waste ammonium as PP-V.

Extreme ultra-violet emission spectroscopy of highly charged gadolinium ions with an electron beam ion trap

International Nuclear Information System (INIS)

Ohashi, Hayato; Nakamura, Nobuyuki; Sakaue, Hiroyuki A

2013-01-01

We present extreme ultra-violet emission spectra of highly charged gadolinium ions obtained with an electron beam ion trap at electron energies of 0.53–1.51 keV. The electron energy dependence of the spectra in the 5.7–11.3 nm range is compared with calculation with the flexible atomic code. (paper)

The adsorption of mercury on tungsten (100) studied by ultra-violet photoelectron spectroscopy

International Nuclear Information System (INIS)

Egelhoff, W.F. Jr.; Perry, D.L.; Linnett, J.W.

1976-01-01

In recent years, photoelectron spectroscopy has been applied to the study of adsorption on several metal surfaces. A popular choice of substrate has been the 100 face of single crystal tungsten, since adsorption on this surface has been well-characterised by a wide variety of experimental techniques. In this letter a study of the adsorption of mercury on W(100) by ultra-violet photoelectron spectroscopy (UPS) is reported. These results, seen in the context of previous UPS studies of chemisorption, show a number of interesting features. (Auth.)

Extreme ultra-violet movie camera for imaging microsecond time scale magnetic reconnection

International Nuclear Information System (INIS)

Chai, Kil-Byoung; Bellan, Paul M.

2013-01-01

An ultra-fast extreme ultra-violet (EUV) movie camera has been developed for imaging magnetic reconnection in the Caltech spheromak/astrophysical jet experiment. The camera consists of a broadband Mo:Si multilayer mirror, a fast decaying YAG:Ce scintillator, a visible light block, and a high-speed visible light CCD camera. The camera can capture EUV images as fast as 3.3 × 10 6 frames per second with 0.5 cm spatial resolution. The spectral range is from 20 eV to 60 eV. EUV images reveal strong, transient, highly localized bursts of EUV radiation when magnetic reconnection occurs

Extreme ultra-violet movie camera for imaging microsecond time scale magnetic reconnection

Energy Technology Data Exchange (ETDEWEB)

Chai, Kil-Byoung; Bellan, Paul M. [Applied Physics, Caltech, 1200 E. California Boulevard, Pasadena, California 91125 (United States)

2013-12-15

An ultra-fast extreme ultra-violet (EUV) movie camera has been developed for imaging magnetic reconnection in the Caltech spheromak/astrophysical jet experiment. The camera consists of a broadband Mo:Si multilayer mirror, a fast decaying YAG:Ce scintillator, a visible light block, and a high-speed visible light CCD camera. The camera can capture EUV images as fast as 3.3 × 10{sup 6} frames per second with 0.5 cm spatial resolution. The spectral range is from 20 eV to 60 eV. EUV images reveal strong, transient, highly localized bursts of EUV radiation when magnetic reconnection occurs.

Towards dating Quaternary sediments using the quartz Violet Stimulated Luminescence (VSL) signal

DEFF Research Database (Denmark)

Ankjærgaard, C.; Jain, Mayank; Wallinga, J.

2013-01-01

Quaternary sediments using the violet (402 nm) stimulated luminescence (VSL) signal of quartz.We develop and test a new post-blue VSL single aliquot regenerative dose dating protocol, and demonstrate that the VSL signal originates from a deep trap at about 1.9 eV with a thermal lifetime of 1011 years at 10......Quartz optically stimulated luminescence (OSL) dating is widely used to determine the time of deposition and burial of Late Quaternary sediments. Application of the method is usually limited to the past 150,000 years due to early saturation of the OSL signal. Here we explore the potential to date...

DETERMINATION OF THE THERMODYNAMICS OF β-LACTOGLOBULIN AGGREGATION USING ULTRA VIOLET LIGHT SCATTERING SPECTROSCOPY

OpenAIRE

Belton, Daniel; Austerberry, James

2018-01-01

The problem of protein aggregation is widely studied across a number of disciplines, where understanding the behaviour of the protein monomer, and its behaviour with co-solutes is imperative in order to devise solutions to the problem. Here we present a method for measuring the kinetics of protein aggregation based on ultra violet light scattering spectroscopy (UVLSS) across a range of NaCl conditions. Through measurement of wavelength dependant scattering and using the model protein β-lactog...

Surface enrichment with chrome and nitriding of IF steel under an abnormal glow discharge; Enriquecimento superficial com cromo e nitretacao do aco IF em descarga eletrica em regime anormal

Energy Technology Data Exchange (ETDEWEB)

Meira, S.R.; Borges, P.C., E-mail: sabrina.r.meira@gmail.com [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Grupo de Materiais; Bernardelli, E.A. [Instituto Federal do Parana (IFPR), Paranagua, PR (Brazil). Laboratorio de Materiais

2014-07-01

The objective of this work is to evaluate the influence of surface enrichment of IF steel with chrome, and nitriding, the formation of the nitrided layer. Thus, IF steel samples were subjected to surface enrichment process, using 409 stainless steel as a target for sputtering, followed by plasma nitriding, both under a dc abnormal glow discharge. The enrichment treatment was operated at 1200 ° C for 3h. The nitriding treatment was operated at 510 ° C for 2 h. The influence of the treatments on the layers formed was studied through optical microscopy (OM), scan electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microindentation. The results show that the enrichment is effective to enrich the IF surface, furthermore, improves the characteristics of nitriding, comparing nitriding samples to nitriding and enriched, was observed needles of nitrides, as well as a higher hardness, which is associated with the nitrides of chrome, on the nitriding and enriched samples. (author)

PHOTOCATALYTIC REMOVAL OF TR I- AND HEXA-VALENT CHROMIUM IONS FROM CHROME-ELECTROPL ATING WASTEWATER

Directory of Open Access Journals (Sweden)

Puangrat Kajitvichyanukul

2017-11-01

Full Text Available A novel technique based on photocatalysis was applied to eliminate chromium ions, a toxic hazardous environmental pollutant. The photoreduction of each species of chromium (total, hexavalent, and trivalent chromiums from chrome-electroplating wastewater was investigated using a titanium dioxide suspension under irradiation by a low-pressure mercury lamp. The initial concentration of total chromium was 300 mg/l. The applied conditions were the direct photocatalytic reduction process at pH 3.65 and the indirect photocatalytic reduction with added hole scavengers at the same solution pH. Results from both processes were comparatively discussed. Result show that chromium was not efficiently removed by direct photoreduction. In contrast, with the adding of hole scavengers, which were formate ions, the photoreduction of chromium was very favorable. Both hexavalent and trivalent chromiums were efficiently removed. The photocatalytic mechanism is purposed in this study.

Bioremoval of Basic Violet 3 and Acid Blue 93 by Pseudomonas putida and its adsorption isotherms and kinetics.

Science.gov (United States)

Arunarani, A; Chandran, Preethy; Ranganathan, B V; Vasanthi, N S; Sudheer Khan, S

2013-02-01

Basic Violet 3 and Acid Blue 93 are the most important group of synthetic colourants extensively used in textile industries for dyeing cotton, wool, silk and nylon. Release of these dye pollutants in to the environment adversely affects the human health and aquatic organisms. The present study we used Pseudomonas putida MTCC 4910 for the adsorptive removal of Basic Violet 3 and Acid Blue 93 from the aqueous solutions. The pH (4-9) and NaCl concentrations (1mM-1M) did not influence the adsorption process. The equilibrium adsorption process fitted well to Freundlich model than Langmuir model. The kinetics of adsorption fitted well by pseudo-second-order. Thus in the present study an attempt has been made to exploit the dye removal capability of P. putida MTCC 4910, and it was found to be an efficient microbe that could be used for bio removal of dyes from textile effluents. Copyright © 2012 Elsevier B.V. All rights reserved.

Development of a Large-Format Science-Grade CMOS Active Pixel Sensor, for Extreme Ultra Violet Spectroscopy and Imaging in Space Science

National Research Council Canada - National Science Library

Waltham, N. R; Prydderch, M; Mapson-Menard, H; Morrissey, Q; Turchetta, R; Pool, P; Harris, A

2005-01-01

We describe our programme to develop a large-format science-grade CMOS active pixel sensor for future space science missions, and in particular an extreme ultra-violet spectrograph for solar physics...

Effect of QW thickness and numbers on performance characteristics of deep violet InGaN MQW lasers

Science.gov (United States)

Alahyarizadeh, Gh.; Amirhoseiny, M.; Hassan, Z.

2015-03-01

The performance characteristics of deep violet indium gallium nitride (InGaN) multiquantum well (MQW) laser diodes (LDs) with an emission wavelength of around 390 nm have been investigated using the integrated system engineering technical computer aided design (ISE-TCAD) software. A comparative study on the effect of quantum well (QW) thickness and number on electrical and optical performance of deep violet In0.082Ga0.918N/GaN MQW LDs have been carried out. The simulation results showed that the highest slope efficiency and external differential quantum efficiency (DQE), as well as the lowest threshold current are obtained when the number of wells is two. The different QW thickness values of 2.2, 2.5, 2.8, 3 and 3.2 nm were compared and the best results were achieved for 2.5 nm QW thickness. The radiative recombination rate decreases with increasing QW thickness because of decreasing electron and hole carrier densities in wells. By increasing QW thickness, output power decreases and threshold current increases.

Nucleotide sequence of the 3' ends of the double-stranded RNAs of grapevine chrome mosaic nepovirus.

Science.gov (United States)

Le Gall, O; Candresse, T; Dunez, J

1988-02-01

Attempts were made to label the termini of dsRNAs corresponding to the two genomic RNAs of grapevine chrome mosaic nepovirus (GCMV). It was not possible to label the 5' ends of the dsRNAs with [gamma-32P]ATP, which suggests that a genome-linked protein blocks their 5' ends. Both dsRNA species were labelled at their 3' ends with pCp. The 3'-terminal sequences were determined by 'wandering spot' or by partial enzymic cleavage analysis. One strand (presumably positive) ended in a poly(A) 30 to 50 nucleotides long whereas the other (presumably negative) ended in 3'-ACCUUUUAAAAAG (RNA1) or 3'-ACCUUUUAAUAAAG (RNA2). The sequences resemble closely those complementary to the 5' ends of the RNAs of tomato black ring virus (strain S), which is distantly related to GCMV.

Emission during the firing of chrome-magnesite products in tunnel kilns

Energy Technology Data Exchange (ETDEWEB)

Krechin, Yu.V.; Telegin, S.V.; Ivanov, N.M.; Kasimov, A.M.; Plichko, E.P.; Sverkov, Yu.M.; Maksimov, B.N.

1986-11-01

When chrome-magnesite products are fired in tunnel furnaces, the concentration in the effluent gas of dust is 110-150; of Cr/sub 7/O/sub 3/, 5-7; NO/sub x/, 20-35; CO, 100-125; SO/sub 2/, 25-40; and SO/sub 3/, 30-70 mg/m/sup 3/. The emission dust is finely dispersed. The average size of the particles of dust is 0.3, the minimum 0.05, and the maximum 1 ..mu..m. There is no hydrogen sulfide, NO/sub 2/, or CrO/sub 3/ in the emission. Dust and nitrogen oxides are formed in the firing zone of the kiln. The formation of dust and NO/sub 2/ depends on the air-consumption coefficient. The use of the pipe-in-pipe type of ports does not provide good gas combustion. To improve the operation of the kiln and the combustion of the natural gas it is recommended that instead of the obsolescent tube-in-tube ports, the ports developed by the Eastern Institute of Refractories be installed since they have given good results in tests. To improve the scattering effect of the removal of dust in the existing equipment it is recommended that the height of the flue stacks be increased to 40-50 m.

Investigation of the interaction of chrome compounds with blue-green microalgae Spirulina platensis

International Nuclear Information System (INIS)

Mosulishvili, L.M.; Belokobyl'skij, A.I.; Kirkesali, E.I.; Frontas'eva, M.V.; Pavlov, S.S.; Aksenova, N.G.

2002-01-01

The interaction of CrIII with the cells of blue-green microalgae Spirulina platensis in course of cultivation in a nutrient medium loaded with corresponding chrome compounds is studied. It is shown that the rate of absorption of CrVI ions by spirulina biomass from the nutrient medium is approximately two orders of magnitude lower as compared to that of CrIII ions. At the same time the presence of CrVI in a nutrient medium is accompanied by a significant decrease in the cell growth rate and by deteriorating the quality of spirulina biomass. It is established that at endogenous insertion of CrIII into the biocomplex of spirulina no change in the valence state of chromium in the nutrient medium is observed and the natural properties of the biomass do not change. On the basis of the obtained concentration dependences, the recommended doses of CrIII in the preparation 'Cr-Spirulina' within the ranges of 30-100 μg/g as a food addition, and 200-250 μg/g for a medical preventive treatment are determined. (author)

A numerical investigation into the influence of the properties of cobalt chrome cellular structures on the load transfer to the periprosthetic femur following total hip arthroplasty.

Science.gov (United States)

Hazlehurst, Kevin Brian; Wang, Chang Jiang; Stanford, Mark

2014-04-01

Stress shielding of the periprosthetic femur following total hip arthroplasty is a problem that can promote the premature loosening of femoral stems. In order to reduce the need for revision surgery it is thought that more flexible implant designs need to be considered. In this work, the mechanical properties of laser melted square pore cobalt chrome molybdenum cellular structures have been incorporated into the design of a traditional monoblock femoral stem. The influence of incorporating the properties of cellular structures on the load transfer to the periprosthetic femur was investigated using a three dimensional finite element model. Eleven different stiffness configurations were investigated by using fully porous and functionally graded approaches. This investigation confirms that the periprosthetic stress values depend on the stiffness configuration of the stem. The numerical results showed that stress shielding is reduced in the periprosthetic Gruen zones when the mechanical properties of cobalt chrome molybdenum cellular structures are used. This work identifies that monoblock femoral stems manufactured using a laser melting process, which are designed for reduced stiffness, have the potential to contribute towards reducing stress shielding. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Responses of macaque ganglion cells to far violet lights

International Nuclear Information System (INIS)

De Monasterio, F.M.; Gouras, P.

1977-01-01

In a sample of 487 colour-opponent ganglion cells recorded in the central retina of the rhesus and cynomolgus monkeys, 9% of these neurones were found to have responses with the same sign at both ends of the visible spectrum mediated by red-sensitive cones and mid-spectral responses of opposite sign mediated by green-sensitive cones. Selective chromatic adaptation showed that the responses to far violet lights (400 to 420 nm) were due to input from red- and not blue-sensitive cones. These responses were enhanced by backgrounds depressing the sensitivity of blue- and green-sensitive cones and they were depressed by backgrounds depressing the sensitivity of red-sensitive cones; the sensitivity of these responses was yoked to that of responses to far red lights. The relative incidence of these ganglion cells was maximal at the foveal region and decreased towards the peripheral retina. The properties of these cells are consistent with some psychophysical observations of human vision at the short wave-lengths. (author)

REMOVAL OF CRYSTAL VIOLET BY BIOSORPTION ONTO DATE STONES

Directory of Open Access Journals (Sweden)

NOUREDDINE EL MESSAOUDI

2016-07-01

Full Text Available The biosorption has the advantage that it can be applied to effluent disposal and thus brings various responses to the regulatory requirements for environmental protection. This study presents the results obtained from the use of date stones (DS for the elimination of crystal violet (CV from aqueous medium. Several analysis techniques were used to determine the different characteristics of biosorbent studied (FTIR, TGA-DTA, SEM and pHzpc.The physico-chemical parameters influence of the biosorption such as biosorbent dosage, contact time, temperature, biosorbent particles size and initial dye pH were investigated under static conditions in order to evaluate the process system. The test results show that a gram of date stones may set a maximum amount adsorbed 90.89 mg·g-1 of CV at 50 °C according to the Langmuir isotherm with pseudo-second-order kinetic. Thermodynamic calculations performed shows also that sorption is spontaneous, endothermic and increased randomness in the solid / solution interface.

Enhancing Surface Finish of Additively Manufactured Titanium and Cobalt Chrome Elements Using Laser Based Finishing

Science.gov (United States)

Gora, Wojciech S.; Tian, Yingtao; Cabo, Aldara Pan; Ardron, Marcus; Maier, Robert R. J.; Prangnell, Philip; Weston, Nicholas J.; Hand, Duncan P.

Additive manufacturing (AM) offers the possibility of creating a complex free form object as a single element, which is not possible using traditional mechanical machining. Unfortunately the typically rough surface finish of additively manufactured parts is unsuitable for many applications. As a result AM parts must be post-processed; typically mechanically machined and/or and polished using either chemical or mechanical techniques (both of which have their limitations). Laser based polishing is based on remelting of a very thin surface layer and it offers potential as a highly repeatable, higher speed process capable of selective area polishing, and without any waste problems (no abrasives or liquids). In this paper an in-depth investigation of CW laser polishing of titanium and cobalt chrome AM elements is presented. The impact of different scanning strategies, laser parameters and initial surface condition on the achieved surface finish is evaluated.

Tunable blue–violet Cr3+:LiCAF + BiBO compact laser

International Nuclear Information System (INIS)

Maestre, H; Torregrosa, A J; Capmany, J

2015-01-01

We present a compact continuous wave (CW) external-cavity tunable Cr 3+ :LiCaAlF 6 (Cr:LiCAF) laser which is intracavity frequency doubled using a BiB 3 O 6 (BiBO) nonlinear crystal to obtain tunable blue–violet radiation. The generated second harmonic (SH) can be tuned by means of either angular or temperature variation of the nonlinear crystal. We have obtained SH radiation between 390–415 nm and a maximum output power of 34 mW at 400 nm. Future improvements on the SH tuning range and output power are addressed in the text. Our results may be applied in the design of compact tunable composite external-cavity solid-state lasers. (paper)

Using violet laser-induced chlorophyll fluorescence emission spectra for crop yield assessment of cowpea (Vigna unguiculata (L) Walp) varieties

Science.gov (United States)

Anderson, Benjamin; Buah-Bassuah, Paul K.; Tetteh, Jonathan P.

2004-07-01

The use of violet laser-induced chlorophyll fluorescence (LICF) emission spectra to monitor the growth of five varieties of cowpea in the University of Cape Coast Botanical Garden is presented. Radiation from a continuous-wave violet laser diode emitting at 396 nm through a fibre is closely incident on in vivo leaves of cowpea to excite chlorophyll fluorescence, which is detected by an integrated spectrometer with CCD readout. The chlorophyll fluorescence spectra with peaks at 683 and 731 nm were used for growth monitoring of the cowpea plants over three weeks and analysed using Gaussian spectral functions with curve fitted parameters to determine the peak positions, area under the spectral curve and the intensity ratio F683/F731. The variation in the intensity ratio of the chlorophyll bands showed sensitive changes indicating the photosynthetic activity of the cowpea varieties. A discussion of the fluorescence result as compared to conventional assessment is presented with regard to discrimination between the cowpea varieties in terms of crop yield performance.

Electronic structure of superconducting Bi2212 crystal by angle resolved ultra violet photoemission

International Nuclear Information System (INIS)

Saini, N.L.; Shrivastava, P.; Garg, K.B.

1993-01-01

The electronic structure of a high quality superconducting Bi 2 Sr 2 CaCu 2 Osub(8+δ) (Bi2212) single crystal is studied by angle resolved ultra violet photoemission (ARUPS) using He I (21.2 eV). Our results appear to show two bands crossing the Fermi level in ΓX direction of the Brillouin zone as reported by Takahashi et al. The bands at higher binding energy do not show any appreciable dispersion. The nature of the states near the Fermi level is discussed and the observed band structure is compared with the band structure calculations. (author)

Adsorption of gentian violet dyes in aqueous solution on microporous AlPOs molecular sieves synthesized by ionothermal method

Science.gov (United States)

Fortas, W.; Djelad, A.; Hasnaoui, M. A.; Sassi, M.; Bengueddach, A.

2018-02-01

In this work, AlPO-34, like-chabazite (CHA) zeolite, was ionothermally prepared using the ionic liquid (IL), 1-ethyl-3-methylimidazolium chloride [EMIMCl], as solvent. The solids obtained were characterized by x-ray powder diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (FTIR), thermal analysis (TG) and nitrogen adsorption/desorption at 77.3 K. The results show that the ionic liquid is occluded in the AlPO-34 framework and consequently it acts also as a structure-directing agent. The variation of chemical composition led to AlPO-34 materials with different crystal sizes and morphologies. The well crystallized AlPO-34 material was used as adsorbent for Crystal Violet (CV) dye removal from aqueous solutions. The effect of adsorption parameters such as pH and initial concentration were investigated. It was found that adsorption dyes is favorable at pH = 6. The adsorption isotherm data follow the Langmuir equation in which parameters are calculated. The selected AlPO-34 sample exhibited a high crystal violet dye removal of 46.08 mg g-1 at pH = 6.

Spectrally-isolated violet to blue wavelength generation by cascaded degenerate four-wave mixing in a photonic crystal fiber.

Science.gov (United States)

Yuan, Jinhui; Kang, Zhe; Li, Feng; Zhang, Xianting; Zhou, Guiyao; Sang, Xinzhu; Wu, Qiang; Yan, Binbin; Zhou, Xian; Wang, Liang; Zhong, Kangping; Wang, Kuiru; Yu, Chongxiu; Tam, Hwa Yaw; Wai, P K A

2016-06-01

Generation of spectrally-isolated wavelengths in the violet to blue region based on cascaded degenerate four-wave mixing (FWM) is experimentally demonstrated for the first time in a tailor-made photonic crystal fiber, which has two adjacent zero dispersion wavelengths (ZDWs) at 696 and 852 nm in the fundamental mode. The influences of the wavelength λp and the input average power Pav of the femtosecond pump pulses on the phase-matched frequency conversion process are studied. When femtosecond pump pulses at λp of 880, 870, and 860 nm and Pav of 500 mW are coupled into the normal dispersion region close to the second ZDW, the first anti-Stokes waves generated near the first ZDW act as a secondary pump for the next FWM process. The conversion efficiency ηas2 of the second anti-Stokes waves, which are generated at the violet to blue wavelengths of 430, 456, and 472 nm, are 4.8, 6.48, and 9.66%, for λp equalling 880, 870, and 860 nm, respectively.

Synthesis of SnO{sub 2}-activated carbon fiber hybrid catalyst for the removal of methyl violet from water

Energy Technology Data Exchange (ETDEWEB)

Li, Jia, E-mail: mse_lij@ujn.edu.cn [School of Material Science and Engineering, University of Jinan, Jinan 250022 (China); Ng, Dickon H.L. [Department of Physics, The Chinese University of Hong Kong, Shatin, Hong Kong (China); Song, Peng; Kong, Chao; Song, Yi [School of Material Science and Engineering, University of Jinan, Jinan 250022 (China)

2015-04-15

Graphical abstract: - Highlights: • A new biomass route for the synthesis of SnO{sub 2}/ACF hybrid catalyst was proposed. • The original fibrous structure of kapok fiber was retained in the SnO{sub 2}/ACF hybrid catalyst. • SnO{sub 2}/ACF hybrid catalyst exhibited high BET surface area (647–897 m{sup 2}/g) and large pore volume (0.36–0.56 cm{sup 3} g{sup −1}). • High microwave-induced catalytic activity for methyl violet degradation was obtained. - Abstract: SnO{sub 2}/activated carbon fiber (ACF) hybrid catalyst was synthesized from kapok precursor via a two-step process involving pore-fabricating and self-assembly of SnO{sub 2} nanoparticles. The morphology and phase structure of the obtained samples were characterized by X-ray diffraction, field emission scanning electron microscope, high resolution transmission electron microscopy and N{sub 2} adsorption-desorption isotherm. These results demonstrated that the synthesized SnO{sub 2}/ACF retained the hollow-fiber structure of kapok fibers. SnO{sub 2} nanoparticles dispersed uniformly over the ACF support. The obtained hybrid catalyst showed porous structure with high surface area (647–897 m{sup 2}/g) and large pore volume (0.36–0.56 cm{sup 3} g{sup −1}). In addition, the catalytic activities of the obtained samples for methyl violet degradation under microwave irradiation were also evaluated. It was found that the SnO{sub 2}/ACF catalyst exhibited high catalytic activity for methyl violet degradation due to the synergistic effect of microwave and SnO{sub 2}/ACF catalyst.

Vacuum ultra-violet and electron energy loss spectroscopy of gaseous and solid organic compounds

International Nuclear Information System (INIS)

Koch, E.E.; Otto, A.

1976-01-01

The experimental arrangements used by the authors for the study of optical vacuum ultra-violet and electron energy loss spectra of organic compounds are described and some theoretical aspects of studies of higher excited states are considered. Results for alkanes, benzene, naphthalene, anthracene and some more complex hydrocarbons are reviewed. Recent results obtained by reflection and electron energy loss spectroscopy for single crystals of anthracene are included and their relevance for gas phase work as well as for the understanding of exciton effects in organic solids is described. (author)

Étude de l’évolution de la teneur en chrome hexavalent dans le cuir, influence des conditions de fabrication et importance des facteurs environnementaux

OpenAIRE

Fontaine , Mathilde

2017-01-01

Currently, 80 to 85% of leather is tanned with chrome. This process allows to obtain excellent physico-mechanical properties with optimum economic conditions. The chromium salts in trivalent form used in the manufacturing of leather are not harmful; however under some conditions and associated with other substances, trivalent chromium can be transformed into hexavalent chromium, highly allergenic and potentially harmful to the health of the consumer. Since 1st May 2015, the presence of hexava...

Colorimetric Nucleic Acid Detection on Paper Microchip Using Loop Mediated Isothermal Amplification and Crystal Violet Dye.

Science.gov (United States)

Roy, Sharmili; Mohd-Naim, Noor Faizah; Safavieh, Mohammadali; Ahmed, Minhaz Uddin

2017-11-22

Nucleic acid detection is of paramount importance in monitoring of microbial pathogens in food safety and infectious disease diagnostic applications. To address these challenges, a rapid, cost-effective label-free technique for nucleic acid detection with minimal instrumentations is highly desired. Here, we present paper microchip to detect and quantify nucleic acid using colorimetric sensing modality. The extracted DNA from food samples of meat as well as microbial pathogens was amplified utilizing loop-mediated isothermal amplification (LAMP). LAMP amplicon was then detected and quantified on a paper microchip fabricated in a cellulose paper and a small wax chamber utilizing crystal violet dye. The affinity of crystal violet dye toward dsDNA and positive signal were identified by changing the color from colorless to purple. Using this method, detection of Sus scrofa (porcine) and Bacillus subtilis (bacteria) DNA was possible at concentrations as low as 1 pg/μL (3.43 × 10 -1 copies/μL) and 10 pg/μL (2.2 × 10 3 copies/μL), respectively. This strategy can be adapted for detection of other DNA samples, with potential for development of a new breed of simple and inexpensive paper microchip at the point-of-need.

Determination of Cr2O3 in chrome-tanned leather by radionuclide-excited X-ray fluorescence analysis

International Nuclear Information System (INIS)

Melich, M.; Palagyi, S.; Kern, M.

1989-01-01

Preliminary results on the determination of Cr 2 O 3 in chrome-tanned leather by measuring the content of Cr by means of radionuclide-excited XRF analysis are reported. For excitation a 3.7 GBq 238 Pu source was used and the characteristic K X-rays of Cr were detected with a planar Si(Li) detector. Both smooth and rough sides of the leather were analyzed directly or with a pair of V/Ti balanced filters. A fairly good correlation was found between Cr Kx counts of the rough side and the Cr 2 O 3 concentrations determined chemically in the range of 3.5 to 6.0% Cr 2 O 3 . The method renders possible a rapid and non-destructive determination of Cr 2 O 3 in various leather samples. (author)

75 FR 12497 - Carbazole Violet Pigment 23 from India and the People's Republic of China: Final Results of the...

Science.gov (United States)

2010-03-16

... Pigment 23 from India and the People's Republic of China: Final Results of the Expedited Sunset Reviews of... antidumping duty orders on carbazole violet pigment 23 (CVP 23) from India and the People's Republic of China... Five-Year (``Sunset'') Review, 74 FR 56593 (November 2, 2009) (Notice of Initiation). The Department...

Second Harmonic Generation of Violet Light in Femtosecond-Laser-Inscribed BiB3O6 Cladding Waveguides

Directory of Open Access Journals (Sweden)

Jia Yuechen

2013-11-01

Full Text Available We report on the second harmonic generation of violet light of a nonlinear cladding waveguide in BiB3O6 crystal produced by femtosecond laser inscription. Under continuous-wave pump laser at 800 nm, the guided second harmonic wave at 400 nm with a conversion efficiency of ~0.32% has been realized through the Type I birefringence phase matching configuration.

The relationship between the violet pigment PP-V production and intracellular ammonium level in Penicillium purpurogenum

OpenAIRE

Kojima, Ryo; Arai, Teppei; Matsufuji, Hiroshi; Kasumi, Takafumi; Watanabe, Taisuke; Ogihara, Jun

2016-01-01

Penicillium purpurogenum is the fungus that produces an azaphilone pigment. However, details about the pigment biosynthesis pathway are unknown. The violet pigment PP-V is the one of the main pigments biosynthesized by this fungus. This pigment contains an amino group in a pyran ring as its core structure. We focused on this pigment and examined the relationship between intracellular ammonium concentration and pigment production using glutamine as a nitrogen source. The intracellular ammonium...

Complementary ion and extreme ultra-violet spectrometer for laser-plasma diagnosis.

Science.gov (United States)

Ter-Avetisyan, S; Ramakrishna, B; Doria, D; Sarri, G; Zepf, M; Borghesi, M; Ehrentraut, L; Stiel, H; Steinke, S; Priebe, G; Schnürer, M; Nickles, P V; Sandner, W

2009-10-01

Simultaneous detection of extreme ultra-violet (XUV) and ion emission along the same line of sight provides comprehensive insight into the evolution of plasmas. This type of combined spectroscopy is applied to diagnose laser interaction with a spray target. The use of a micro-channel-plate detector assures reliable detection of both XUV and ion signals in a single laser shot. The qualitative analysis of the ion emission and XUV spectra allows to gain detailed information about the plasma conditions, and a correlation between the energetic proton emission and the XUV plasma emission can be suggested. The measured XUV emission spectrum from water spray shows efficient deceleration of laser accelerated electrons with energies up to keV in the initially cold background plasma and the collisional heating of the plasma.

Complementary ion and extreme ultra-violet spectrometer for laser-plasma diagnosis

International Nuclear Information System (INIS)

Ter-Avetisyan, S.; Ramakrishna, B.; Doria, D.; Sarri, G.; Zepf, M.; Borghesi, M.; Ehrentraut, L.; Stiel, H.; Steinke, S.; Schnuerer, M.; Nickles, P. V.; Sandner, W.; Priebe, G.

2009-01-01

Simultaneous detection of extreme ultra-violet (XUV) and ion emission along the same line of sight provides comprehensive insight into the evolution of plasmas. This type of combined spectroscopy is applied to diagnose laser interaction with a spray target. The use of a micro-channel-plate detector assures reliable detection of both XUV and ion signals in a single laser shot. The qualitative analysis of the ion emission and XUV spectra allows to gain detailed information about the plasma conditions, and a correlation between the energetic proton emission and the XUV plasma emission can be suggested. The measured XUV emission spectrum from water spray shows efficient deceleration of laser accelerated electrons with energies up to keV in the initially cold background plasma and the collisional heating of the plasma.

Application of Micro-cloud point extraction for spectrophotometric determination of Malachite green, Crystal violet and Rhodamine B in aqueous samples

Science.gov (United States)

Ghasemi, Elham; Kaykhaii, Massoud

2016-07-01

A novel, green, simple and fast method was developed for spectrophotometric determination of Malachite green, Crystal violet, and Rhodamine B in water samples based on Micro-cloud Point extraction (MCPE) at room temperature. This is the first report on the application of MCPE on dyes. In this method, to reach the cloud point at room temperature, the MCPE procedure was carried out in brine using Triton X-114 as a non-ionic surfactant. The factors influencing the extraction efficiency were investigated and optimized. Under the optimized condition, calibration curves were found to be linear in the concentration range of 0.06-0.60 mg/L, 0.10-0.80 mg/L, and 0.03-0.30 mg/L with the enrichment factors of 29.26, 85.47 and 28.36, respectively for Malachite green, Crystal violet, and Rhodamine B. Limit of detections were between 2.2 and 5.1 μg/L.

Development of spectrophotometric determination of beryllium in beryl minerals using chrome Azurol S

Directory of Open Access Journals (Sweden)

Hisham K. Fouad

2016-09-01

Full Text Available A developed, direct, rapid, and sensitive spectrophotometric determination of beryllium in beryl minerals with Chrome Azurol S (CAS as a chromogenic reagent was developed in the present article. The determination was performed without either solvent extraction or ion exchange separation of beryllium from its matrix. The stable 1:1 Be-CAS complex was formed instantly with duration time of at least 24 h with constant absorbance. Different parameters such as wavelengths, pH, EDTA concentration and dye concentration were studied for the optimum determination of beryllium. Interference due to presence of high aluminum concentrations was overcome by adding 5% EDTA disodium salt solution. Maximum absorbance for Be-CAS complex was performed at λmax 568 NM using acetate buffer at pH 4.6. Beer’s law was obeyed in the range from 0.02 to 9 ppm with molar absorptivity ε = 0.22 × 104 mol−1 cm−1 and an average standard deviation of 0.7. The R.S.D for 10 replicate measurements of 1 ppm Be was 1.2%.

Violet-green excitation for NIR luminescence of Yb3+ ions in Bi2O3-B2O3-SiO2-Ga2O3 glasses.

Science.gov (United States)

Li, Weiwei; Cheng, Jimeng; Zhao, Guoying; Chen, Wei; Hu, Lili; Guzik, Malgorzata; Boulon, Georges

2014-04-21

60Bi(2)O(3)-20B(2)O(3)-10SiO(2)-10Ga(2)O(3) glasses doped with 1-9 mol% Yb(2)O(3) were prepared and investigated mainly on their violet-green excitation for the typical NIR emission of Yb(3+), generally excited in the NIR. Two violet excitation bands at 365 nm and 405 nm are related to Yb(2+) and Bi(3+). 465 nm excitation band and 480 nm absorption band in the blue-green are assigned to Bi(0) metal nanoparticles/grains. Yb-content-dependence of the excitation and absorption means that Bi(0) is the reduced product of Bi(3+), but greatly competed by the redox reaction of Yb(2+) ↔ Yb(3+). It is proved that the violet-green excitations result in the NIR emission of Yb(3+). On the energy transfer, the virtual level of Yb(3+)-Yb(3+) as well as Bi(0) dimers probably plays an important role. An effective and controllable way is suggested to achieve nano-optical applications by Bi(0) metal nanoparticles/grains and Yb(3+).

Violet Laser Diode Enables Lighting Communication.

Science.gov (United States)

Chi, Yu-Chieh; Huang, Yu-Fang; Wu, Tsai-Chen; Tsai, Cheng-Ting; Chen, Li-Yin; Kuo, Hao-Chung; Lin, Gong-Ru

2017-09-05

Violet laser diode (VLD) based white-light source with high color rendering index (CRI) for lighting communication is implemented by covering with Y 3 Al 5 O 12 :Ce 3+ (YAG:Ce) or Lu 3 Al 5 O 12 :Ce 3+ /CaAlSiN 3 :Eu 2+ (LuAG:Ce/CASN:Eu) phosphorous diffuser plates. After passing the beam of VLD biased at 70 mA (~2I th ) through the YAG:Ce phosphorous diffuser, a daylight with a correlated color temperature (CCT) of 5068 K and a CRI of 65 is acquired to provide a forward error correction (FEC) certified data rate of 4.4 Gbit/s. By using the VLD biased at 122 mA (~3.5I th ) to excite the LuAG:Ce/CASN:Eu phosphorous diffuser with 0.85-mm thickness, a warm white-light source with a CCT of 2700 K and a CRI of 87.9 is obtained at a cost of decreasing transmission capacity to 2.4 Gbit/s. Thinning the phosphor thickness to 0.75 mm effectively reduces the required bias current by 32 mA to achieve the same CCT for the delivered white light, which offers an enlarged CRI of 89.1 and an increased data rate of 4.4 Gbit/s. Further enlarging the bias current to 105 mA remains the white-light transmission capacity at 4.4 Gbit/s but reveals an increased CCT of 3023 K and an upgraded CRI of 91.5.

Effect of bisquaternary ammonium salts on complexing of metal ions with pyrocatechol violet

International Nuclear Information System (INIS)

Tananajko, M.M.; Kofanova, N.K.

1984-01-01

Conditions for the improvement of contrast and sensitivity of reactions of high-charge ions of metals (Mo, W, La, Cd, Zr, Hf, Th) in the process of their photometric determination with pyrocatechol violet (PV), using bisquaternary ammonium salts (BQAS), have been studied. It is shown that in the systems investigated the BQAS play the role of ''shifting'' reagents, shifting bathochromically the absorption bands of different ligand complexes as compared with absorption bands of the Me-PV binary complexes. The effect of the BQAS on complexing with PV in aqueous and organic phases (chloroform) is studied and potential flotation of the compounds in the phase interface is considered

Exploring the temporally resolved electron density evolution in extreme ultra-violet induced plasmas

International Nuclear Information System (INIS)

Van der Horst, R M; Beckers, J; Nijdam, S; Kroesen, G M W

2014-01-01

We measured the electron density in an extreme ultra-violet (EUV) induced plasma. This is achieved in a low-pressure argon plasma by using a method called microwave cavity resonance spectroscopy. The measured electron density just after the EUV pulse is 2.6 × 10 16  m −3 . This is in good agreement with a theoretical prediction from photo-ionization, which yields a density of 4.5 × 10 16  m −3 . After the EUV pulse the density slightly increases due to electron impact ionization. The plasma (i.e. electron density) decays in tens of microseconds. (fast track communication)

Mask Materials and Designs for Extreme Ultra Violet Lithography

Science.gov (United States)

Kim, Jung Sik; Ahn, Jinho

2018-03-01

Extreme ultra violet lithography (EUVL) is no longer a future technology but is going to be inserted into mass production of semiconductor devices of 7 nm technology node in 2018. EUVL is an extension of optical lithography using extremely short wavelength (13.5 nm). This short wavelength requires major modifications in the optical systems due to the very strong absorption of EUV light by materials. Refractive optics can no longer be used, and reflective optics is the only solution to transfer image from mask to wafer. This is why we need the multilayer (ML) mirror-based mask as well as an oblique incident angle of light. This paper discusses the principal theory on the EUV mask design and its component materials including ML reflector and EUV absorber. Mask shadowing effect (or mask 3D effect) is explained and its technical solutions like phase shift mask is reviewed. Even though not all the technical issues on EUV mask are handled in this review paper, you will be able to understand the principles determining the performance of EUV masks.

Adsorption of Acid Yellow-73 and Direct Violet-51 Dyes from Textile Wastewater by Using Iron Doped Corncob Charcoal

Directory of Open Access Journals (Sweden)

Mujtaba Baqar

2015-06-01

Full Text Available The presence of synthetic dyes in textile industry wastewater lead to deterioration of precious fresh water resources, making the need to remove dyes crucial for environmental protection. Recently, different techniques have been employed to remove these dyes from water resources. Among them, biosorption has gained tremendous popularity due to its eco-friendly nature and inexpensive method. In this study, the removal potential of two acid dyes, i.e. yellow-73 and direct violet-51, was assessed from textile effluent samples using iron modified corncob charcoal. The adsorption efficiency ranged between 93.93 ­ 97.96 % and 92.2 - 95.4 % for acid yellow-73 and direct violet-51, respectively. Furthermore, study highlights optimum parameters for successful adsorption of these dyes, such as stirring time (numbers, pH (numbers, temperature (numbers, and adsorbent dosage (numbers. Keeping in consideration these findings, we recommend the use of Iron Doped Corncob Charcoal (IDCC as a low-cost, efficient alternative for wastewater treatment, primarily minimizing the detrimental effects of hazardous dyes.

Enhanced photocatalytic performance of CeO2-TiO2 nanocomposite for degradation of crystal violet dye and industrial waste effluent

Science.gov (United States)

Zahoor, Mehvish; Arshad, Amara; Khan, Yaqoob; Iqbal, Mazhar; Bajwa, Sadia Zafar; Soomro, Razium Ali; Ahmad, Ishaq; Butt, Faheem K.; Iqbal, M. Zubair; Wu, Aiguo; Khan, Waheed S.

2018-03-01

This study presents the synthesis of CeO2-TiO2 nanocomposite and its potential application for the visible light-driven photocatalytic degradation of model crystal violet dye as well as real industrial waste water. The ceria-titania (CeO2-TiO2) nanocomposite material was synthesised using facile hydrothermal route without the assistance of any template molecule. As-prepared composite was characterised by SEM, TEM, HRTEM, XRD, XPS for surface features, morphological and crystalline characters. The formed nanostructures were determined to possess crystal-like geometrical shape and average size less than 100 nm. The as-synthesised nanocomposite was further investigated for their heterogeneous photocatalytic potential against the oxidative degradation of CV dye taken as model pollutant. The photo-catalytic performance of the as-synthesised material was evaluated both under ultra-violet as well as visible light. Best photocatalytic performance was achieved under visible light with complete degradation (100%) exhibited within 60 min of irradiation time. The kinetics of the photocatalytic process were also considered and the reaction rate constant for CeO2-TiO2 nanocomposite was determined to be 0.0125 and 0.0662 min-1 for ultra-violet and visible region, respectively. In addition, the as-synthesised nanocomposite demonstrated promising results when considered for the photo-catalytic degradation of coloured industrial waste water collected from local textile industry situated in Faisalabad region of Pakistan. Enhanced photo-catalytic performance of CeO2-TiO2 nanocomposite was proposed owing to heterostructure formation leading to reduced electron-hole recombination.

Chrome Tanning Leather of Giant Sea Perch Combined with Seed Extract Areca Nut on the Physical Characteristics

Directory of Open Access Journals (Sweden)

Bustami - Ibrahim

2014-11-01

Full Text Available Tanning is the process of converting raw hide protein to leather, which are stable, not easily decompose, and is suitable for a variety of uses. The use of vegetable based tanning materials in the leather tanning process has not been carried out. Vegetable based materials that were used are betel nuts. This plant contains tannin which is the main agent in the process of leather tanning. The aim of this study was to determine the physical characteristics of snapper leather treated with betel nut extract. Soxhlet extracting method with methanol as a solvent were used to obtain tannin from betel nuts. Tanned Snapper Leather were analyzed for physical quality, elongation strength, tensile strength, tear strength, and sewing strength. The result showed that methanol extracted betel nut with 10% concentration gives the optimum physical characteristics.Keywords: areca nut, chrome, snapper, snapper

Defect-engineered GaN:Mg nanowire arrays for overall water splitting under violet light

International Nuclear Information System (INIS)

Kibria, M. G.; Chowdhury, F. A.; Zhao, S.; Mi, Z.; Trudeau, M. L.; Guo, H.

2015-01-01

We report that by engineering the intra-gap defect related energy states in GaN nanowire arrays using Mg dopants, efficient and stable overall neutral water splitting can be achieved under violet light. Overall neutral water splitting on Rh/Cr 2 O 3 co-catalyst decorated Mg doped GaN nanowires is demonstrated with intra-gap excitation up to 450 nm. Through optimized Mg doping, the absorbed photon conversion efficiency of GaN nanowires reaches ∼43% at 375–450 nm, providing a viable approach to extend the solar absorption of oxide and non-oxide photocatalysts

Photo-oxidation. Of the system chrome hexavalent-4-chlorophenol

International Nuclear Information System (INIS)

Gil Pavas, Edison; Cabrera Limpias, Marianela; Jaramillo Jimenez, Sergio Alejandro

2003-01-01

As a proposal to eliminate highly toxic chemical components derived from industrial waste, the researchers study the behavior of the compound hexavalent chromium / 4-chlorophenol system when subjected to photo degradation in a photo-reactor compound parabolic cylinder (CPC) to scale pilot. The effect is analyzed in order to determine the operation conditions to reach the highest degradation levels possible. The analyzed variables were pH, concentration of catalyst (TiO 2 ), time of recirculation and the relation of initial concentrations among polluting agents. The factor that most influences the levels of removal reached is the pH, which has a different effect for each of the pollutants. This implies that, theoretically, you cannot adopt a unique group of operation parameters to favor the degradation of both however, in the practice; high levels of degradation of both pollutants are obtained in the optimal point of operation of the chrome. It is also observed that the catalyst concentration does not influence the degradation of the polluting agents significantly, at least for the initial concentrations studied. The recirculation time is closely related to the kinetics of degradation of each polluting agent. Elevated degradation levels are reached in a short time for 4-chlorophenol, while more prolonged recirculation times are required for hexavalent chromium. The relation of initial concentrations of the polluting agents also exerts an opposite effect on the degradation levels reached for each polluting agent; the hexavalent chromium reduction is favored with high initial concentrations of 4-chlorophenol, whereas the oxidation of 4-chlorophenol is favored with high initial hexavalent chromium concentrations, which suggests some synergy between the oxidation-reduction reactions of 4-chlorophenol and hexavalent chromium. Finally, a 97% hexavalent chromium reduction and a 94.9% oxidation of 4-chlorophenol were obtained

Chromed Leather Dyeing Peculiarities when Deliming with Peracetic Acid

Directory of Open Access Journals (Sweden)

Kęstutis BELEŠKA

2013-05-01

Full Text Available The research was aimed to investigate the influence of deliming with peracetic acid on leather dyeing kinetics. Hydrophobic C.I. Acid Red 213 and hydrophilic C.I. Acid Red 423 dyes were used. Sorption of dye depends on hydrophobicity/hydrophility of dye and dyeing temperature. Equilibrium of process is reached faster using hydrophobic C.I. Acid Red 213 at 45 ºC. However, both control and experimental leather fibres adsorb more hydrophilic dye C.I. Acid Red 423 and this fact does not depend on temperature. The diffusion coefficient of dye C.I. Acid Red 423 calculated according to Weisz model is higher when dyeing conventional leather. The change of deliming method has influence on chromed leather dyeing but this influence is not significant. The adsorption ability of control leather fibres at 30 ºC and 45 ºC is higher using both dyes as compared to the dyeing the experimental one. The increase of dyeing temperature increases the adsorption ability independently on the sort of leather fibres. Such dependence of the adsorption ability on the temperature shows that hydrophobic action and van der Waals forces prevail between dye and fibres during dyeing process. The Gibbs energy changes show that adsorption of both dyes by leather fibres independently on their sort is a spontaneous process. The affinity of both dyes to conventional leather fibres is higher comparing with experimental one. The change of enthalpy is positive in all cases, and it means that the driving force of the dyeing is the change of entropy.DOI: http://dx.doi.org/10.5755/j01.ms.19.2.4431

Long-time rupture strength and creep behaviour of welded joints on heat-resistant CrMoV steels with 1 and 12% chrome

International Nuclear Information System (INIS)

Maier, G.; Maile, K.; Theofel, H.

1985-01-01

Power plant components in the creep range are damaged frequently in the weld joint zones. The investigation concentrated therefore on the reliability of the information supplied by tests on small- and large-size samples. Creep rupture tests of dissimilar welded joints (1% with 12% chrome) with variations of heat input and weld metal have been conducted. At creep rupture times of about 10 4 h all joints failed in the outside heat affected zone of the weaker base metal. Large-size samples, proved in comparison at same stresses, showed distinctly longer times to rupture. (orig.) [de

Reproductive biology of the violet-chested hummingbird in Venezuela and comparisons with other tropical and temperate hummingbirds

Science.gov (United States)

Fierro-Calderon, Karolina; Martin, T.E.

2007-01-01

We provide details on the breeding biology of the Violet-chested Hummingbird (Sternoclyta cyanopectus) based on 67 nests studied in Yacambu?? National Park, Venezuela, from 2002 through 2006. Clutch size was two white eggs, usually laid every other day. Fresh egg mass (0.95 ?? 0.14 g) was 15% of female mass. Incubation and nestling periods were 20.4 ?? 0.3 and 26.0 ?? 0.4 days, respectively. Nest attentiveness increased from 60% in early incubation to 68% in late incubation. The female spent 50% of her time brooding young nestlings, but ceased brooding by 13 days of age. Only the female fed the young, with a low rate of nest visitation (3.3 trips per hour) that did not increase with age of the young. Growth rate based on nestling mass (K = 0.28) was slow. Daily predation rates decreased across stages and were 0.064 ?? 0.044, 0.033 ?? 0.008, and 0.020 ?? 0.006 during the egg-laying, incubation, and nestling periods, respectively. Most, but not all, life history traits of the Violet-chested Hummingbird were similar to those reported for other tropical and temperate hummingbirds, providing further evidence that this family shows a relatively narrow range of life history variation. ?? The Cooper Ornithological Society 2007.

Disinfection of deionised water inoculated with enterobacter using ultra violet light

International Nuclear Information System (INIS)

Mathrani, M.

2001-01-01

For the first time the enterobacter, not the escherichia coli,was used as a model bacteria to asses the disinfection of microorganisms in water by UV (Ultra Violet) irradiation. The cell density of the liquid culture was followed by optical density of 1.837 at 600 nm on spectrometer. For the disinfection purpose, a laboratory scale batch reactor (10 cm wide, 20 cm long, and 10 cm height), containing 250 ml sterilised deionized water inoculated with enterobacter,was run under supra-band gap light (wavelength < 400 nm, peaking between 340 and 365 nm with a maximum of 350 nm). After carrying out seven batch experiments it is concluded that the complete inactivation of Enterobacter ( approx. equal to x 10/sup 6/ CFU/ml) in the water can be achieved by UV irradiation for 2 hours. (author)

Nonlinear Optical Characteristics of Crystal VioletDye Doped Polystyrene Films by Using Z-Scan Technique

Directory of Open Access Journals (Sweden)

Mahasin F. Hadi

2017-07-01

Full Text Available Z-scan technique was employed to study the nonlinear optical properties (nonlinear refractive index and nonlinear absorption coefficient for crystal violet doped polystyrene films as a function of doping ratio in chloroform solvent. Samples exhibits in closed aperture Z-scan positive nonlinear refraction (self-focusing. While in the open aperture Z-scan gives reverse saturation absorption (RSA (positive absorption for all film with different doping ratio making samples candidates for optical limiting devices for protection of sensors and eyes from energetic laser light pulses under the experimental conditions.

Determination of residues of three triphenylmethane dyes and their metabolites (malachite green, leuco malachite green, crystal violet, leuco crystal violet, and brilliant green) in aquaculture products by LC/MS/MS: first action 2012.25.

Science.gov (United States)

Hurtaud-Pessel, Dominique; Couëdor, Pierrick; Verdon, Eric; Dowell, Dawn

2013-01-01

During the AOAC Annual Meeting held from September 30 to October 3, 2012 in Las Vegas, NV, the Expert Review Panel (ERP) on Veterinary Drug Residues reviewed data for the method for determination of residues of three triphenylmethane dyes and their metabolites (malachite green, leuco malachite green, crystal violet, leuco crystal violet, and brilliant green) in aquaculture products by LC/MS/MS, previously published in the Journal of Chromatography A 1218, 1632-1645 (2006). The method data were reviewed and compared to the standard method performance requirements (SMPRs) found in SMPR 2009.001, published in AOAC's Official Methods of Analysis, 19th Ed. (2012). The ERP determined that the data were acceptable, and the method was approved AOAC Official First Action. The method uses acetonitrile to isolate the analyte from the matrix. Then determination is conducted by LCIMS/MS with positive electrospray ionization. Accuracy ranged from 100.1 to 109.8% for samples fortified at levels of 0.5, 0.75, 1.0, and 2.0 microg/kg. Precision ranged from 2.0 to 10.3% RSD for the intraday samples and 1.9 to 10.6% for the interday samples analyzed over 3 days. The described method is designed to accurately operate in the analytical range from 0.5 to 2 microg/kg, where the minimum required performance limit for laboratories has been fixed in the European Union at 2.0 microg/kg for these banned substances and their metabolites. Upper levels of concentrations (1-100 microg/kg) can be analyzed depending on the different optional calibrations used.

Shock-Assisted Superficial Hexagonal-to-Cubic Phase Transition in GaN/Sapphire Interface Induced by Using Ultra-violet Laser Lift-Of Techniques

International Nuclear Information System (INIS)

Wei-Hua, Chen; Xiao-Dong, Hu; Xiang-Ning, Kang; Xu-Rong, Zhou; Xiao-Min, Zhang; Tong-Jun, Yu; Zhi-Jian, Yang; Ke, Xu; Guo-Yi, Zhang; Xu-Dong, Shan; Li-Ping, You

2009-01-01

Ultra-violet (KrF excimer laser, λ = 248 nm) laser lift-of (LLO) techniques have been operated to the GaN/sapphire structure to separate GaN from the sapphire substrate. Hexagonal to cubic phase transformation induced by the ultra-violet laser lift-of (UV-LLO) has been characterized by micro-Raman spectroscopy, micro-photoluminescence, along with high-resolution transmission electron microscopy (HRTEM). HRTEM indicates that UV-LLO induced phase transition takes place above the LLO interface, without phase transition under the LLO interface. The formed cubic GaN often exists as nanocrystal grains attaching on the bulk hexagonal GaN. The half-loop-cluster-like UV-LLO interface indicates that the LLO-induced shock waves has generated and played an assistant role in the decomposition of the hexagonal GaN and in the formation of cubic GaN grains at the LLO surface

Adsorption of Crystal Violet on Activated Carbon Prepared from Coal Flotation Concentrate

Science.gov (United States)

Aydogmus, Ramazan; Depci, Tolga; Sarikaya, Musa; Riza Kul, Ali; Onal, Yunus

2016-10-01

The objective of this study is firstly to investigate the floatability properties of Zilan- Van coal after microwave irradiation and secondly to produce activated carbon from flotation concentrate in order to remove Crystal Violet (CV) from waste water. The flotation experiments showed that microwave heating at 0.9 kW power level for 60 sec exposure time enhanced the hydrophobicity and increased the flotation yield. The activated carbon with remarkable surface area (696 m2/g) was produced from the flotation concentrate and used to adsorb CV from aqueous solution in a batch reactor at different temperature. The adsorption properties of CV onto the activated carbon are discussed in terms of the adsorption isotherms (Langmuir and Freundlich) and found that the experimental results best fitted by the Langmuir model.

Toward the Extreme Ultra Violet Four Wave Mixing Experiments: From Table Top Lasers to Fourth Generation Light Sources

OpenAIRE

Riccardo Cucini; Andrea Battistoni; Filippo Bencivenga; Alessandro Gessini; Riccardo Mincigrucci; Erika Giangrisostomi; Emiliano Principi; Flavio Capotondi; Emanuele Pedersoli; Michele Manfredda; Maya Kiskinova; Claudio Masciovecchio

2015-01-01

Three different Transient Grating setups are presented, with pulsed and continuous wave probe at different wavelengths, ranging from infrared to the extreme ultra violet region. Both heterodyne and homodyne detections are considered. Each scheme introduces variations with respect to the previous one, allowing moving from classical table top laser experiments towards a new four wave mixing scheme based on free electron laser radiation. A comparison between the various setups and the first resu...

Red/violet contrast reversal on Mars - significance for eolian sediments

International Nuclear Information System (INIS)

Thomas, P.; Veverka, J.

1986-01-01

Viking Orbiter images of Mars are analyzed to define relationships between the observed contrast reversals (CR) and specific surface features. The link between CR phenomena and surface composition was first detected in contrast comparisons between UV and visible wavelength Mariner 9 data. Viking data, taken through red and violet filters, showed that the CRs occurred only with crater splotches and splotch-related streaks and in bright depositional and dark erosional streaks, both being low-albedo markings presumably caused by eolian forces. The splotch phenomena is confined mainly to the Oxia Palus region, although there are other regions where splotches and streaks commingle. Laboratory tests to mimic the CR characteristics showed that CRs are a common phenomena of different size fractions of iron oxides, e.g., goethite, where particles under 5 microns have been removed. The splotches, including dune formations, are therefore believed to indicate the presence of particles in the 100-800 microns diam range. Finer particles ride on the tops of the dust storms, and are continually removed from the surface by saltation. 51 references

arXiv Blue and violet graviton spectra from a dynamical refractive index

CERN Document Server

Giovannini, Massimo

We show that the spectral energy distribution of relic gravitons mildly increases for frequencies smaller than the $\\mu$Hz and then flattens out whenever the refractive index of the tensor modes is dynamical during a quasi-de Sitter stage of expansion. For a conventional thermal history the high-frequency plateau ranges between the mHz and the audio band but it is supplemented by a spike in the GHz region if a stiff post-inflationary phase precedes the standard radiation-dominated epoch. Even though the slope is blue at intermediate frequencies, it may become violet in the MHz window. For a variety of post-inflationary histories, including the conventional one, a dynamical index of refraction leads to a potentially detectable spectral energy density in the kHz and in the mHz regions while all the relevant phenomenological constraints are concurrently satisfied.

Crystal Violet and Methylene Green as Low-Dose Liquid Dosimetry Systems

International Nuclear Information System (INIS)

Ebraheem, S.; Beshir, W.B.; Hassan, H.M.

2008-01-01

The ultimate aim of the present work is studying of the possibility of using some organic solutions for gamma radiation monitors and to evaluate and characterize the dosimetric properties of these compounds. Crystal violet (CV) and methylene green (MG) aqueous solutions with different concentrations have been prepared and irradiated to different absorbed doses. The solutions were readout using absorption spectrophotometry technique at λ m ax 592 nm and 614 nm for CV and MG respectively. The maximum useful dose range was investigated and found to be concentration dependent. It was found that the useful dose range was from 10-160 Gy for CV and from 10-200 Gy for MG. The radiation chemical yield, G-value, was calculated for the studied solutions. The ph effect and the effect of different additives, chloral hydrate and ethanol have been also investigated. The pre- and post- irradiation stabilities of these solutions under different storage conditions were studied and the results showed different significant dependence on the storage condition

A novel electrochemical sensor for the analysis of β-agonists: The poly(acid chrome blue K)/graphene oxide-nafion/glassy carbon electrode

Energy Technology Data Exchange (ETDEWEB)

Lin, Xiaoyun [State Key Laboratory of Food Science and Technology, Nanchang University, Nanchang 330047 (China); Ni, Yongnian, E-mail: ynni@ncu.edu.cn [State Key Laboratory of Food Science and Technology, Nanchang University, Nanchang 330047 (China); Department of Chemistry, Nanchang University, Nanchang 330031 (China); Kokot, Serge, E-mail: s.kokot@qut.edu.au [School of Chemistry, Physics and Mechanical Engineering, Queensland University of Technology, Brisbane 4001 (Australia)

2013-09-15

Graphical abstract: A new modified electrode was constructed by the electro-polymerization of acid chrome blue K (ACBK) at a graphene-nafion modified glassy carbon electrode (GCE). The novel electrode was successfully employed for the analysis of eight β-agonist analytes with high sensitivity. -- Highlights: • Construction of the poly-ACBK/graphene-nafion/GCE. •The modified electrode showed high sensitivity for the analysis of the β-agonists. • A novel method was successfully developed for the analysis of clenbuterol in pork. • Research provided a new method of constructing electrodes for biological analysis. -- Abstract: A novel modified electrode was constructed by the electro-polymerization of 4,5-dihydroxy-3-[(2-hydroxy-5-sulfophenyl)azo]-2,7-naphthalenedisulfonic acid trisodium salt (acid chrome blue K (ACBK)) at a graphene oxide (GO)-nafion modified glassy carbon electrode (GCE). The characterization of an electrochemically synthesized poly-ACBK/GO-nafion film was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), atomic force microscopy (AFM) and scanning electron microscopy (SEM) techniques, and the results were interpreted and compared at each stage of the electrode construction. Electrochemical oxidation of eight β-agonists – clenbuterol, salbutamol, terbutaline, ractopamine, dopamine, dobutamine, adrenaline, and isoprenaline, was investigated by CV at the different electrodes. At the poly-ACBK/GO-nafion/GCE, the linear sweep voltammetry peak currents of the eight β-agonists increased linearly with their concentrations in the range of 1.0–36.0 ng mL{sup −1}, respectively, and their corresponding limits of detection (LODs) were within the 0.58–1.46 ng mL{sup −1} range. This electrode showed satisfactory reproducibility and stability, and was used successfully for the quantitative analysis of clenbuterol in pork samples.

In vitro processing of the RNA-2-encoded polyprotein of two nepoviruses: tomato black ring virus and grapevine chrome mosaic virus.

Science.gov (United States)

Demangeat, G; Hemmer, O; Fritsch, C; Le Gall, O; Candresse, T

1991-02-01

In vitro translation of RNA-2 of each of two closely related nepoviruses, tomato black ring virus (TBRV) and grapevine chrome mosaic virus (GCMV), in a rabbit reticulocyte lysate resulted in the synthesis of single polypeptides of 150K and 146K respectively. Processing of these polyproteins occurred after the addition of translation products of homologous RNA-1. The positions of the cleavage products within the polyproteins were determined. From the N to the C terminus, Mr values for the proteins were 50K, 46K and 59K for TBRV and 44K, 46K and 56K for GCMV. TBRV RNA-1 translation products also cleaved the polyproteins encoded by GCMV RNA-2 which suggests that the cleavage sites in the two polyproteins are similar.

Photoconversion changes bilin chromophore conjugation and protein secondary structure in the violet/orange cyanobacteriochrome NpF2164g3' [corrected].

Science.gov (United States)

Lim, Sunghyuk; Rockwell, Nathan C; Martin, Shelley S; Dallas, Jerry L; Lagarias, J Clark; Ames, James B

2014-06-01

Cyanobacteriochromes (CBCRs) are cyanobacterial photoreceptors distantly related to phytochromes. All CBCRs examined to date utilize a conserved Cys residue to form a covalent thioether linkage to the bilin chromophore. In the insert-Cys CBCR subfamily, a second conserved Cys can covalently link to the bilin C10 methine bridge, allowing detection of near-UV to blue light. The best understood insert-Cys CBCR is the violet/orange CBCR NpF2164g3 from Nostoc punctiforme, which has a stable second linkage in the violet-absorbing dark state. Photoconversion of NpF2164g3 leads to elimination of the second linkage and formation of an orange-absorbing photoproduct. We recently reported NMR chemical shift assignments for the orange-absorbing photoproduct state of NpF2164g3. We here present equivalent information for its violet-absorbing dark state. In both photostates, NpF2164g3 is monomeric in solution and regions containing the two conserved Cys residues essential for photoconversion are structurally disordered. In contrast to blue light receptors such as phototropin, NpF2164g3 is less structurally ordered in the dark state than in the photoproduct. The insert-Cys insertion loop and C-terminal helix exhibit light-dependent structural changes. Moreover, a motif containing an Asp residue also found in other CBCRs and in phytochromes adopts a random-coil structure in the dark state but a stable α-helix structure in the photoproduct. NMR analysis of the chromophore is consistent with a less ordered dark state, with A-ring resonances only resolved in the photoproduct. The C10 atom of the bilin chromophore exhibits a drastic change in chemical shift upon photoconversion, changing from 34.5 ppm (methylene) in the dark state to 115 ppm (methine) in the light-activated state. Our results provide structural insight into the two-Cys photocycle of NpF2164g3 and the structurally diverse mechanisms used for light perception by the larger phytochrome superfamily.

Detection of biological warfare agents using ultra violet-laser induced fluorescence LIDAR.

Science.gov (United States)

Joshi, Deepti; Kumar, Deepak; Maini, Anil K; Sharma, Ramesh C

2013-08-01

This review has been written to highlight the threat of biological warfare agents, their types and detection. Bacterial biological agent Bacillus anthracis (bacteria causing the disease anthrax) which is most likely to be employed in biological warfare is being discussed in detail. Standoff detection of biological warfare agents in aerosol form using Ultra violet-Laser Induced Fluorescence (UV-LIF) spectroscopy method has been studied. Range-resolved detection and identification of biological aerosols by both nano-second and non-linear femto-second LIDAR is also discussed. Calculated received fluorescence signal for a cloud of typical biological agent Bacillus globigii (Simulants of B. anthracis) at a location of ~5.0 km at different concentrations in presence of solar background radiation has been described. Overview of current research efforts in internationally available working UV-LIF LIDAR systems are also mentioned briefly. Copyright © 2013 Elsevier B.V. All rights reserved.

Degradation of Polymers by Ultra-Violet Light

Energy Technology Data Exchange (ETDEWEB)

Turner, D. T. [Camille Dreyfus Laboratory, Research Triangle Institute, Research Triangle Park, NC (United States)

1968-10-15

To reach an understanding of the complex processes which occur when polymers are degraded by ultra-violet light under service conditions it is first judicious to try to elucidate the photochemistry of relatively simple polymer reactions. For this reason, emphasis is given to studies in which purified polymers, in bulk, were exposed to monochromatic radiations in the absence of oxygen. In respect of product analysis, emphasis is given to methods for estimating quantum yields for fractures and crosslinks. Photochemical mechanisms are illustrated by discussion of polystyrene, polytethylene terephthalate) and cellulose. Special emphasis is given to the role of free radicals. Attention is drawn to reports that the course of photolysis may be changed by application of an external pressure of a chemically inert gas, such as nitrogen. The explanation suggested in the literature is that this depends on the ease of escape of hydrogen atoms which, alternatively, might react with trapped polymer radicals. The course of photolysis may also be affected by polymer radicals acting as strongly absorbing chromophores and consequently undergoing further chemical reaction. This is illustrated by reference to the conversion of allyl radicals to alkyl radicals in polyethylene and also by changes observed in the ESR spectrum of polymer radicals trapped in poly (ethylene terephthalate) as a result of exposure to light. It is suggested that this effect is primarily responsible for the evolution of hydrocarbon gases on photolysis of polyethylene or natural rubber. In contrast, radiolysis of these polymers yields almost pure hydrogen because, in this case, energy is absorbed by relatively non-selective processes, i.e. free radicals do not absorb high energy radiation much more strongly than does their polymeric environment. (author)

Tritium decontamination of TFTR carbon tiles employing ultra violet light

International Nuclear Information System (INIS)

Shu, W.M.; Ohira, S.; Gentile, C.A.; Oya, Y.; Nakamura, H.; Hayashi, T.; Iwai, Y.; Kawamura, Y.; Konishi, S.; Nishi, M.F.; Young, K.M.

2001-01-01

Tritium decontamination on the surface of Tokamak Fusion Test Reactor (TFTR) bumper limiter tiles used during the Deuterium-Deuterium (D-D) phase of TFTR operations was investigated employing an ultra violet light source with a mean wavelength of 172 nm and a maximum radiant intensity of 50 mW/cm 2 . The partial pressures of H 2 , HD, C and CO 2 during the UV exposure were enhanced more than twice, compared to the partial pressures before UV exposure. In comparison, the amount of O 2 decreased during the UV exposure and the production of a small amount of O 3 was observed when the UV light was turned on. Unlike the decontamination method of baking in air or oxygen, the UV exposure removed hydrogen isotopes from the tile to vacuum predominantly in forms of gases of hydrogen isotopes. The tritium surface contamination on the tile in the area exposed to the UV light was reduced after the UV exposure. The results show that the UV light with a wavelength of 172 nm can remove hydrogen isotopes from carbon-based tiles at the very surface

Research on the use of Ferro-Chrome slag in civil engineering applications

Directory of Open Access Journals (Sweden)

Al-Jabri Khalifa S.

2018-01-01

Full Text Available Over recent decades there has been rapid increase in the industrial waste materials and by-products yields due to the progressive growth rate of population, development of industry and technology and the growth of consumerism. With the growing environmental pressures to reduce waste and pollution, Intensive research studies have been conducted to explore all suitable reuse methods. Wastes such as construction waste, blast furnace, steel slag, coal fly ash and bottom ash have been approved in many places as alternative materials in bridges, roads, pavements, foundations and building construction. The use of industrial solid waste as a partial replacement of raw materials in construction activities not only saves landfill space but also reduces the demand for extraction of natural raw materials. Ferrochrome slag is a by-product from the production of chrome. There are environmental and economic advantages in seeing slags as a potentially useful resource rather than as waste products. Slag management at ferrochrome producing companies has been influenced by the limited space available and financial cost implications of the slag dumps. Internationally, e.g. South Africa, India, Norway, Turkey, East Europe, China, Sweden and USA, ferrochrome slag is used commercially in the road and construction Industries. This material is being used for road construction, as aggregates in concrete industry, brick manufacturing, and in pavement construction as engineering fill and has recently been tried in cement. This paper presents an overview of the recent advances of the use of ferrochrome slag in various civil engineering applications such as road construction, and cement and concrete industries.

Electronic structure, excitation properties, and chemical transformations of extreme ultra-violet resist materials

Science.gov (United States)

Rangan, Sylvie; Bartynski, Robert A.; Narasimhan, Amrit; Brainard, Robert L.

2017-07-01

The electronic structure of extreme ultra violet resist materials and of their individual components, two polymers and two photoacid generators (PAGs), is studied using a combination of x-ray and UV photoemission spectroscopies, electron energy loss spectroscopy, and ab-initio techniques. It is shown that simple molecular models can be used to understand the electronic structure of each sample and describe the experimental data. Additionally, effects directly relevant to the photochemical processes are observed: low energy loss processes are observed for the phenolic polymer containing samples that should favor thermalization of electrons; PAG segregation is measured at the surface of the resist films that could lead to surface inhomogeneities; both PAGs are found to be stable upon irradiation in the absence of the polymer, contrasting with a high reactivity that can be followed upon x-ray irradiation of the full resist.

Violet Light Exposure Can Be a Preventive Strategy Against Myopia Progression

Directory of Open Access Journals (Sweden)

Hidemasa Torii

2017-02-01

Full Text Available Prevalence of myopia is increasing worldwide. Outdoor activity is one of the most important environmental factors for myopia control. Here we show that violet light (VL, 360–400 nm wavelength suppresses myopia progression. First, we confirmed that VL suppressed the axial length (AL elongation in the chick myopia model. Expression microarray analyses revealed that myopia suppressive gene EGR1 was upregulated by VL exposure. VL exposure induced significantly higher upregulation of EGR1 in chick chorioretinal tissues than blue light under the same conditions. Next, we conducted clinical research retrospectively to compare the AL elongation among myopic children who wore eyeglasses (VL blocked and two types of contact lenses (partially VL blocked and VL transmitting. The data showed the VL transmitting contact lenses suppressed myopia progression most. These results suggest that VL is one of the important outdoor environmental factors for myopia control. Since VL is apt to be excluded from our modern society due to the excessive UV protection, VL exposure can be a preventive strategy against myopia progression.

Highly stable colloidal TiO2 nanocrystals with strong violet-blue emission

International Nuclear Information System (INIS)

Ghamsari, Morteza Sasani; Gaeeni, Mohammad Reza; Han, Wooje; Park, Hyung-Ho

2016-01-01

Improved sol–gel method has been applied to prepare highly stable colloidal TiO 2 nanocrystals. The synthesized titania nanocrystals exhibit strong emission in the violet-blue wavelength region. Very long evolution time was obtained by preventing the sol to gel conversion with reflux process. FTIR, XRD, UV–vis absorption, photoluminescence and high resolution transmission electron microscope (HRTEM) were used to study the optical properties, crystalline phase, morphology, shape and size of prepared TiO 2 colloidal nanocrystals. HRTEM showed that the diameter of TiO 2 colloidal nanocrystals is about 5 nm. Although the PL spectra show similar spectral features upon excitation wavelengths at 280, 300 and 350 nm, but their emission intensities are significantly different from each other. Photoluminescence quantum yield for TiO 2 colloidal nanocrystals is estimated to be 49% with 280 nm excitation wavelength which is in agreement and better than reported before. Obtained results confirm that the prepared colloidal TiO 2 sample has enough potential for optoelectronics applications.

Spectrophotometric Microdetermination of Thorium(IV and Uranium(VI with Chrome Azurol-S in Presence of Cationic Surfactant

Directory of Open Access Journals (Sweden)

A. B. Upase

2011-01-01

Full Text Available Cationic surfactant, cetyldimethylethylammonium bromide (CDMEAB, sensitize the color reactions of Th(IV and U(VI with chrome azurol-S(CRAS. Formation of water soluble deeply colored ternary complexes of metal ions show large bathochromic shift. Same stoichiometric composition of ternary complexes with 1:2:4 molar ratio (M-CRAS-CDMEAB have been observed for both the metal ions and are responsible for enhancement in molar absorptivities and sensitivities at shifted wavelength. The ternary complexes of thorium(IV and uranium(VI exhibit absorption maxima at 640 and 620 nm with molar absorptivities 85500 and 69600 L.mol-1.cm-2 respectively. Beer’s law were obeyed in concentration range 0.12-0.185 ppm for Th(IV and 0.13-0.162 ppm for U(VI in presence of CDMEAB. Conditional formation constants and various analytical parameters have been evaluated and compared the results of binary and ternary complexes. Enhancement in the molar absorptivities in presence of CDMEAB clearly indicated the usefulness of these colored reactions for microdetermination.

A review on management of chrome-tanned leather shavings: a holistic paradigm to combat the environmental issues.

Science.gov (United States)

Pati, Anupama; Chaudhary, Rubina; Subramani, Saravanabhavan

2014-10-01

Raw hide/skins come to the tanners as a by-product of meat industry which is converted into value-added leather as product for fashion market. Leather manufacturing is a chemical process of natural biological matrix. It employs a huge quantity of water and inorganic and organic chemicals for processing and thereby discharges solid and liquid wastes into the environment. One of the potential solid wastes generated from leather industry is chrome-tanned leather shavings (CTLSs), and its disposal is increasingly becoming a huge challenge on disposal to tanners due to presence of heavy metal chromium. Hence, finding a sustainable solution to the CTLS disposal problem is a prime challenge for global tanners and researchers. This paper aims to the deeper review of various disposal methods on CTLS such as protein, chromium, and energy recovery processes and its utilization methodologies. Sustainable technologies have been developed to overcome CTLS solid wastes emanating from leather processing operations. Further, this review paper brings a broader classification of developed methodologies for treatment of CTLSs.

2-Chlorophenol Removal of Aqueous Solution Using Advanced Oxidation Processes Resulting from Iron/ Persulfate and Ultra Violet/ Persulfate

Directory of Open Access Journals (Sweden)

Shokufeh Astereki

2016-06-01

Full Text Available Background: Advanced oxidation processes are used to remove toxic aromatic compounds with low biodegradability, such as 2-chlorophenol. This study investigated the use of sulfate (SO4- and persulfate (S2O82- radicals, as one of the advanced oxidation methods, to remove 2- chlorophenol from aquatic solutions. Methods: This experimental and pilot-scale study was carried out using two chemical batch reactors; one of the reactors equipped with UV lamps and the other was on the hot plate. In iron/ persulfate (Fe/S2O82- and ultra violet/ persulfate (UV/S2O82- processes different parameters were investigated. Results: Iron, UV, the initial pH of the solution, persulfate concentration have considerable effects on the elimination of 2-chlorophenol in both processes. In both processes, the maximum elimination occurred in acidic conditions. The elimination efficiency was increased by increasing the concentration of 2-chlorophenol and UV intensity, and also by decreasing the concentration of persulfate and iron. Accordingly, in iron/ persulfate and ultra violet/ persulfate processes 2-chlorophenol was eliminated with 99.96% and 99.58% efficiencies, respectively. Conclusion: Sulfate radicals produced from activated persulfate ions with hot-Fe ion and UV radiation have significant impact on the removal of 2-chlorophenol. Therefore, the processes of Fe/S2O82- and UV/S2O82- can be regarded as good choices for industrial wastewater treatment plants operators in the future.

UV-vis, IR and 1H NMR spectroscopic studies and characterization of ionic-pair crystal violet-oxytetracycline

Science.gov (United States)

Orellana, Sandra; Soto, César; Toral, M. Inés

2010-01-01

The present study shows the formation and characterization of the ionic-pair between the antibiotic oxytetracycline and the dye crystal violet in ammonia solution pH 9.0 ± 0.2 extracted into chloroform. The characterization was demonstrated using UV-vis spectrophotometry, 1H NMR, measurement of relaxation times T1 and IR spectroscopy, using a comparison between the signals of individual pure compounds with the signals with the mixture CV-OTC in different alkaline media. The formation of ionic-pair was also corroborated by new signals and chemical shifts. (2D) NMR spectroscopy experiments show that the interaction is electrostatic.

MOVPE growth of violet GaN LEDs on β-Ga2O3 substrates

Science.gov (United States)

Li, Ding; Hoffmann, Veit; Richter, Eberhard; Tessaro, Thomas; Galazka, Zbigniew; Weyers, Markus; Tränkle, Günther

2017-11-01

We report that a H2-free atmosphere is essential for the initial stage of metalorganic vapour phase epitaxy (MOVPE) growth of GaN on β-Ga2O3 to prevent the surface from damage. A simple growth method is proposed that can easily transfer established GaN growth recipes from sapphire to β-Ga2O3 with both (-2 0 1) and (1 0 0) orientations. This method features a thin AlN nucleation layer grown below 900 °C in N2 atmosphere to protect the surface of β-Ga2O3 from deterioration during further growth under the H2 atmosphere. Based on this, we demonstrate working violet vertical light emitting diodes (VLEDs) on n-conductive β-Ga2O3 substrates.

Post-column reaction for simultaneous analysis of chromatic and leuco forms of malachite green and crystal violet by high-performance liquid chromatography with photometric detection

Science.gov (United States)

Allen, J.L.; Meinertz, J.R.

1991-01-01

The chromatic and leuco forms of malachite green and crystal violet were readily separated and detected by a sensitive and selective high-performance liquid chromatographic procedure. The chromatic and leuco forms of the dyes were separated within 11 min on a C18 column with a mobile phase of 0.05 M sodium acetate and 0.05 M acetic acid in water (19%) and methanol (81%). A reaction chamber, containing 10% PbO2 in Celite 545, was placed between the column and the spectrophotometric detector to oxidize the leuco forms of the dyes to their chromatic forms. Chromatic and leuco malachite green were quantified by their absorbance at 618 nm; and chromatic and leuco Crystal Violet by their absorbance at 588 nm. Detection limits for chromatic and leuco forms of both dyes ranged from 0.12 to 0.28 ng. A linear range of 1 to 100 ng was established for both forms of the dyes.

Probing surface plasmons in individual Ag nanoparticles in the ultra-violet spectral regime.

Science.gov (United States)

Chu, Ming-Wen; Sharma, Pradeep; Chang, Ching-Pin; Liou, Sz Chian; Tsai, Kun-Tong; Wang, Juen-Kai; Wang, Yuh-Lin; Chen, Cheng Hsuan

2009-06-10

Previous investigations of surface plasmons in Ag largely focused on their excitations in the visible spectral regime. Using scanning transmission electron microscopy with an electron beam of 0.2 nm in conjunction with electron energy-loss spectroscopy, we spectrally and spatially probe the surface plasmons in individual Ag nanoparticles (approximately 30 nm), grown on Si, in the ultra-violet spectral regime. The nanomaterials show respective sharp and broad surface-plasmon resonances at approximately 3.5 eV (approximately 355 nm) and approximately 7.0 eV (approximately 177 nm), and the correlated spectral calculations established their multipolar characteristics. The near-field distributions of the surface plasmons on the nanoparticles were also mapped out, revealing the predominant dipolar nature of the 3.5 eV excitation with obvious near-field enhancements at one end of the nano-object. The unveiled near-field enhancements have potential applications in plasmonics and molecular sensing.

Probing surface plasmons in individual Ag nanoparticles in the ultra-violet spectral regime

International Nuclear Information System (INIS)

Chu, M-W; Chang, C-P; Liou, S C; Wang, J-K; Chen, C H; Sharma, Pradeep; Tsai, K-T; Wang, Y-L

2009-01-01

Previous investigations of surface plasmons in Ag largely focused on their excitations in the visible spectral regime. Using scanning transmission electron microscopy with an electron beam of 0.2 nm in conjunction with electron energy-loss spectroscopy, we spectrally and spatially probe the surface plasmons in individual Ag nanoparticles (∼30 nm), grown on Si, in the ultra-violet spectral regime. The nanomaterials show respective sharp and broad surface-plasmon resonances at ∼3.5 eV (∼355 nm) and ∼7.0 eV (∼177 nm), and the correlated spectral calculations established their multipolar characteristics. The near-field distributions of the surface plasmons on the nanoparticles were also mapped out, revealing the predominant dipolar nature of the 3.5 eV excitation with obvious near-field enhancements at one end of the nano-object. The unveiled near-field enhancements have potential applications in plasmonics and molecular sensing.

Light-Induced Fluorescence Modulation of Quantum Dot-Crystal Violet Conjugates: Stochastic Off-On-Off Cycles for Multicolor Patterning and Super-Resolution.

Science.gov (United States)

Jung, Sungwook; Park, Joonhyuck; Bang, Jiwon; Kim, Jae-Yeol; Kim, Cheolhee; Jeon, Yongmoon; Lee, Seung Hwan; Jin, Ho; Choi, Sukyung; Kim, Bomi; Lee, Woo Jin; Pack, Chan-Gi; Lee, Jong-Bong; Lee, Nam Ki; Kim, Sungjee

2017-06-07

Photoswitching or modulation of quantum dots (QDs) can be promising for many fields that include display, memory, and super-resolution imaging. However, such modulations have mostly relied on photomodulations of conjugated molecules in QD vicinity, which typically require high power of high energy photons at UV. We report a visible light-induced facile modulation route for QD-dye conjugates. QD crystal violets conjugates (QD-CVs) were prepared and the crystal violet (CV) molecules on QD quenched the fluorescence efficiently. The fluorescence of QD-CVs showed a single cycle of emission burst as they go through three stages of (i) initially quenched "off" to (ii) photoactivated "on" as the result of chemical change of CVs induced by photoelectrons from QD and (iii) back to photodarkened "off" by radical-associated reactions. Multicolor on-demand photopatterning was demonstrated using QD-CV solid films. QD-CVs were introduced into cells, and excitation with visible light yielded photomodulation from "off" to "on" and "off" by nearly ten fold. Individual photoluminescence dynamics of QD-CVs was investigated using fluorescence correlation spectroscopy and single QD emission analysis, which revealed temporally stochastic photoactivations and photodarkenings. Exploiting the stochastic fluorescence burst of QD-CVs, simultaneous multicolor super-resolution localizations were demonstrated.

Wood (Bagassa guianensis Aubl) and green coconut mesocarp (cocos nucifera) residues as textile dye removers (Remazol Red and Remazol Brilliant Violet).

Science.gov (United States)

Monteiro, Mônica S; de Farias, Robson F; Chaves, José Alberto Pestana; Santana, Sirlane A; Silva, Hildo A S; Bezerra, Cícero W B

2017-12-15

In this work the efficiency of two lignocellulosic waste materials, wood residues and coconut mesocarp, were investigated as adsorbents towards two representative textile dyes (Remazol Red, RR and Remazol Brilliant Violet, RBV). The moisture, carbohydrate, protein, lipid, ash and fiber contents of both natural matrices were characterized. The materials were also characterized by infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, specific surface area analysis and thermogravimetry. The adsorption of dyes was monitored by using UV-Vis spectrophotometry. It was verified that both, coconut mesocarp (CM) and wood residues can act as effective adsorbents towards the investigated dyes. It is verified that the maximum adsorption capacity Γ M (mg g -1 ) for RBV and RR are 7.28 and 3.97 towards CM and 0.64 and 0.71 towrads SD. Furthermore, it was verified that the adsorption is strongly pH dependent and, as a general behavior, an increase in the pH value is associated with a decrease of the total amount of adsorbed dye. The adsorption of violet dye onto coconut mesocarp is well described by the Langmuir model, while all the remazol red fitted better with the Freundlich equation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Crystal violet: Study of the photo-fading of an early synthetic dye in aqueous solution and on paper with HPLC-PDA, LC-MS and FORS

NARCIS (Netherlands)

Confortin, D.; Neevel, H.; Brustolon, M.; Franco, L.; Kettelarij, A.J.; Williams, R.M.; van Bommel, M.R.

2010-01-01

The photo-fading of crystal violet (CV), one of the earliest synthetic dyes and an ink component, is examined both in solution and on paper. Aqueous solutions of CV were exposed to UV light (365nm) and samples were taken at constant time intervals and analysed with a High Performance Liquid

Utilization of cocoa pod husk waste as potential adsorbents for Remazol Brilliant Violet 5R removal

International Nuclear Information System (INIS)

Tan Tong Siang; Mohd Azmier Ahmad

2010-01-01

Removal of Remazol Brilliant Violet 5R (RBV5R) dye from aqueous solution by adsorption onto activated carbon produced from cocoa pod husk (CPH) waste was investigated. Adsorption isotherms were derived at 30 degree Celsius on the basis of batch analysis. Isotherm data were treated according to Langmuir and Freundlich models. Kinetics of adsorption was followed by in situ UV-spectroscopy and the data were treated according to pseudo-first-order and pseudo-second-order models. The fits of experimental data to these equations were examined. It was found that the adsorption process by RVB5R dye onto activated carbon (AC) follows the Freundlich and pseudo-first-order model. (author)

Application of ionizing radiation on industry waste treatment I. radiolysis of standard reactive dye Cibacron violet

International Nuclear Information System (INIS)

Winarti Andayani; Agustin Sumartono

1999-01-01

The effect of aeration, irradiation dose and pH on radiation degradation of reactive dye cibacron violet 2r in aqueous solution have been studied. Observation was done on the absorption spectrum before and after irradiation at various conditions. The percentage of degraded sample was analyzed by using HPLC with UV detector. The percentage of degradation was higher by aeration during irradiation. It suggest that oxygen is important for degradation of the dye molecule. Irradiation at neutral pH is preferred to obtain maximum degradation, since pH may affect the reactivity of the radicals produced by the radiolysis of water molecules. One of the degradation product that could be detected was oxalic acid. (author)

Exposure to Crystal Violet, Its Toxic, Genotoxic and Carcinogenic Effects on Environment and Its Degradation and Detoxification for Environmental Safety.

Science.gov (United States)

Mani, Sujata; Bharagava, Ram Naresh

2016-01-01

Crystal Violet (CV), a triphenylmethane dye, has been extensively used in human and veterinary medicine as a biological stain, as a textile dye in textile processing industries and also used to provide a deep violet color to paints and printing ink. CV is also used as a mutagenic and bacteriostatic agent in medical solutions and antimicrobial agent to prevent the fungal growth in poultry feed. Inspite of its many uses, CV has been reported as a recalcitrant dye molecule that persists in environment for a long period and pose toxic effects in environment. It acts as a mitotic poison, potent carcinogen and a potent clastogene promoting tumor growth in some species of fish. Thus, CV is regarded as a biohazard substance. Although, there are several physico-chemical methods such as adsorption, coagulation and ion-pair extraction reported for the removal of CV, but these methods are insufficient for the complete removal of CV from industrial wastewaters and also produce large quantity of sludge containing secondary pollutants. However, biological methods are regarded as cost-effective and eco-friendly for the treatment of industrial wastewaters, but these methods also have certain limitations. Therefore, there is an urgent need to develop such eco-friendly and cost-effective biological treatment methods, which can effectively remove the dye from industrial wastewaters for the safety of environment, as well as human and animal health.

Equilibrium and Kinetics Study of Adsorption of Crystal Violet onto the Peel of Cucumis sativa Fruit from Aqueous Solution

Directory of Open Access Journals (Sweden)

T. Smitha

2012-01-01

Full Text Available The use of low-cost, locally available, high efficiency and eco-friendly adsorbents has been investigated as an ideal alternative to the current expensive methods of removing dyes from wastewater. This study investigates the potential use of the peel of Cucumis sativa fruit for the removal of crystal violet (CV dye from simulated wastewater. The effects of different system variables, adsorbent dosage, initial dye concentration, pH and contact time were investigated and optimal experimental conditions were ascertained. The results showed that as the amount of the adsorbent increased, the percentage of dye removal increased accordingly. Optimum pH value for dye adsorption was determined as 7.0. The adsorption of crystal violet followed pseudo-second order rate equation and fit well Langmuir and Freundlich equations. The maximum removal of CV was obtained at pH 7 as 92.15% for adsorbent dose of 0.2 g/50 mL and 25 mg L-1 initial dye concentration at room temperature. The maximum adsorption capacity obtained from Langmuir equation was 34.24 mg g-1. Furthermore, adsorption kinetics of (CV was studied and the rate of adsorption was found to conform to pseudo-second order kinetics with a good correlation (R2 > 0.9739. The peel of Cucumis sativa fruit can be attractive options for dye removal from diluted industrial effluents since test reaction made on simulated dyeing wastewater show better removal percentage of (CV.

Thermal behaviour of chrome shavings and of sludges recovered after digestion of tanned solid wastes with calcium hydroxide

International Nuclear Information System (INIS)

Tahiri, S.; Albizane, A.; Messaoudi, A.; Azzi, M.; Bennazha, J.; Younssi, S. Alami; Bouhria, M.

2007-01-01

The thermal behaviour of chrome shavings and of sludges recovered after digestion of tanned wastes with Ca(OH) 2 was studied. Ashes obtained after incineration of wastes at various temperatures were analysed by X-ray diffraction and EDX method. The main crystallized phases present in the ash obtained at 600 deg. C are Cr 2 O 3 and NaCl. The diffractograms revealed an increase in the intensities of the chromium oxide peaks and a very notable decrease of the amount of sodium chloride at 1100 deg. C. EDX analysis revealed a total disappearance of the chlorine peak at this temperature. Scanning electron micrographs show that the waste lost its fibrous aspect when the temperature increases. Formation of aggregates was noted after 550 deg. C. Combustion of organic matters and decarbonation phenomenon are the main stages observed on GTA and DTA curves of sludges. These phenomena are, respectively, exothermic and endothermic. The diffractogram of sludges recorded at 550 deg. C, in the presence of a constant oxygen surplus, revealed the presence of CaCrO 4 and CaCO 3

Transfer of the 3' non-translated region of grapevine chrome mosaic virus RNA-1 by recombination to tomato black ring virus RNA-2 in pseudorecombinant isolates.

Science.gov (United States)

Le Gall, O; Candresse, T; Dunez, J

1995-05-01

In grapevine chrome mosaic and tomato black ring viruses (GCMV and TBRV), as in many other nepoviruses, the 3' non-translated regions (3'NTR) are identical between the two genomic RNAs. We have investigated the structure of the 3'NTR of two recombinant isolates which contain GCMV RNA-1 and TBRV RNA-2. In these isolates, the 3'NTR of RNA-1 was transferred to RNA-2, thus restoring the 3' identity. The transfer occurred within three passages, and probably contributes to the spread of randomly appearing mutations from one genomic RNA to the other. The site of recombination is near the 3' end of the open reading frame.

Cobalt Chrome Spinal Constructs Trigger Airport Security Screening in 24% of Pediatric Patients.

Science.gov (United States)

Woon, Regina P; Andras, Lindsay M; Barrett, Kody K; Skaggs, David L

2015-03-01

Retrospective study. To determine whether pediatric patients undergo additional airport security screening after posterior spinal fusion. Airport security has expanded to include body scanners as well as traditional metal detectors. Families frequently ask whether spinal implants will trigger airport security, but there is limited information on modern implants and screening methods. The researchers conducted a survey of 50 pediatric patients after posterior spinal fusion from 2004 to 2013. Inclusion criteria were posterior instrumentation, pedicle screws for at least 80% of anchors, and at least 1 trip through an American airport after surgery. Charts and radiographs were reviewed for metal type, number of levels fused, number of anchors, and rod diameter. A total of 16% of patients (8 of 50) were detected by body scan or metal detector and all had cobalt chrome (CoCr) rods. No patients with stainless-steel (SS) rods were detected. The CoCr rods triggered additional screening in 24% of children (8 of 33), compared with none of 17 with SS rods (p = .03). For patients with CoCr rods, the detection rate was 18% (5 of 28) by metal detector and 17% (3 of 18) by body scanner. For patients with CoCr rods, there was no significant difference between detection rates and levels fused (p = .30), number of anchors (p = .15), or rod diameter (p = .17). In this series, CoCr constructs were more likely to incur additional airport security compared with more traditional SS constructs. Copyright © 2015 Scoliosis Research Society. Published by Elsevier Inc. All rights reserved.

Metabolomic Profiling of the White, Violet, and Red Flowers of Rhododendron schlippenbachii Maxim.

Science.gov (United States)

Park, Chang Ha; Yeo, Hyeon Ji; Kim, Nam Su; Park, Ye Eun; Park, Soo-Yun; Kim, Jae Kwang; Park, Sang Un

2018-04-04

Rhododendron schlippenbachii Maxim. is a garden plant that is also used for natural medicines as a consequence of the biological activities of its diverse metabolites. We accordingly profiled two anthocyanins and 40 primary and secondary metabolites in the three different colored flowers. The major anthocyanins found in the flowers were cyanidins. The red flowers exhibited the highest accumulation of anthocyanins (1.02 ± 0.02 mg/g dry weight). Principal component analysis was applied to the GC‒TOFMS data. The levels of key tricarboxylic acid cycle intermediates in red flowers, such as succinic acid, fumaric acid, and malic acid, were found to be highly significantly different ( p < 0.0001) from those in the flowers of other colors. In this study, we aimed to determine metabolite interactions and phenotypic variation among white, violet, and red flowers of R. schlippenbachii by using gas chromatography time-of-flight mass spectrometry (GC‒TOFMS) and high-performance liquid chromatography (HPLC).

The induction of species-specific immunity against Schistosoma japonicum by exposure of rats to ultra-violet attenuated cercariae

International Nuclear Information System (INIS)

Moloney, N.A.; Webbe, G.; Hinchcliffe, P.

1987-01-01

Single percutaneous immunizations of Fischer rats with 1000 ultra-violet attenuated Schistosoma japonicum cercariae induced 52-88% resistance to challenge 4 weeks later. Increasing this to 3 immunizations induced 90% resistance to challenge, and this level of protection remained undiminished for up to 40 weeks after vaccination. Rats vaccinated with gamma-irradiated S. mansoni cercariae were resistant to challenge with S. mansoni but not S. japonicum. Similarly rats vaccinated with u.v.-attenuated S. japonicum cercariae were not resistant to heterologous challenge. Thus irradiated vaccines are species-specific in both permissive and non-permissive hosts. (author)

Enhanced adsorption of methyl violet and congo red by using semi and full IPN of polymethacrylic acid and chitosan.

Science.gov (United States)

Maity, Jayabrata; Ray, Samit Kumar

2014-04-15

Semi and full interpenetrating polymer network (IPN) type hydrogels were prepared by free radical in situ polymerization of methacrylic acid in presence of chitosan using N,N'-methylene-bis-acrylamide (MBA) and glutaraldehyde (for full IPN) as crosslinker. Several semi and full IPN type hydrogels were prepared by varying initiator and crosslinker concentration and also monomer to chitosan mass ratio. These hydrogels were characterized and used for removal of methyl violet and congo red dye from water. Isotherms and kinetics of dye adsorption were also evaluated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Low-cost nanoparticles sorbent from modified rice husk and a copolymer for efficient removal of Pb(II) and crystal violet from water.

Science.gov (United States)

Masoumi, Arameh; Hemmati, Khadijeh; Ghaemy, Mousa

2016-03-01

In this work, preparation of adsorbent nanoparticles based on treated low-value agricultural by-product rice husk (TARH), and poly(methylmethacrylate-co-maleic anhydride), poly(MMA-co-MA), is reported for the removal of Pb(II) ion and Crystal violet dye from water. The prepared adsorbent was characterized by FT-IR, SEM, AFM, DLS, BET and Zeta potential. The metal ion adsorption capability was determined for rice husk (RH), TARH, crosslinked poly(MMA-co-MA) (CNR), and CNR@TARH nanoparticles. Different factors affecting the adsorption of Pb(II) such as pH, contact time, initial metal ion concentration and also temperature were studied to investigate adsorption isotherms, kinetics and thermodynamics. For the four tested adsorption isotherm models, the equilibrium sorption data for CNR@TARH nanoparticles obeyed the Langmuir isotherm equation with maximum sorption capacity of 93.45 mg g(-1). The kinetic adsorption data fitted best the Lagergren pseudo-second order model. Regeneration of adsorbent was easily performed by adsorption/desorption experiments followed for 4 cycles. Finally, the ability of the nanoparticles to remove Crystal violet dye from aqueous solution was also investigated by varying the initial dye concentration, pH and immersion time and the adsorption mechanism followed the second-order kinetic model. Copyright © 2015 Elsevier Ltd. All rights reserved.

Measuring the Photocatalytic Breakdown of Crystal Violet Dye using a Light Emitting Diode Approach

Science.gov (United States)

Ryan, Robert E.; Underwood, Lauren W.; O'Neal, Duane; Pagnutti, Mary; Davis, Bruce A.

2009-01-01

A simple method to estimate the photocatalytic reactivity performance of spray-on titanium dioxide coatings for transmissive glass surfaces was developed. This novel technique provides a standardized method to evaluate the efficiency of photocatalytic material systems over a variety of illumination levels. To date, photocatalysis assessments have generally been conducted using mercury black light lamps. Illumination levels for these types of lamps are difficult to vary, consequently limiting their use for assessing material performance under a diverse range of simulated environmental conditions. This new technique uses an ultraviolet (UV) gallium nitride (GaN) light emitting diode (LED) array instead of a traditional black light to initiate and sustain photocatalytic breakdown. This method was tested with a UV-resistant dye (crystal violet) applied to a titanium dioxide coated glass slide. Experimental control is accomplished by applying crystal violet to both titanium dioxide coated slides and uncoated control slides. A slide is illuminated by the UV LED array, at various light levels representative of outdoor and indoor conditions, from the dye side of the slide. To monitor degradation of the dye over time, a temperature-stabilized white light LED, whose emission spectrum overlaps with the dye absorption spectrum, is used to illuminate the opposite side of the slide. Using a spectrometer, the amount of light from the white light LED transmitted through the slide as the dye degrades is monitored as a function of wavelength and time and is subsequently analyzed. In this way, the rate of degradation for photocatalytically coated versus uncoated slide surfaces can be compared. Results demonstrate that the dye absorption decreased much more rapidly on the photocatalytically coated slides than on the control uncoated slides, and that dye degradation is dependent on illumination level. For photocatalytic activity assessment purposes, this experimental configuration and

Optimization of a new polymeric chromium (III) membrane electrode based on methyl violet by using experimental design.

Science.gov (United States)

Kazemi, Sayed Yahya; Hamidi, Akram sadat; Asanjarani, Neda; Zolgharnein, Javad

2010-06-15

Plackett-Burman and Box-Behnken designs were applied as experimental design strategies to screen and optimize the influence of membrane ingredients on the electrode performance. A new poly(vinyl chloride) membrane sensor for Cr(III) based on methyl violet as an ionophore was planned. The major variables to find a model for achieving the best Nernstian slope as response were: PVC, plasticizers, methyl violet, KpClTPB, pH, conditioning time and internal solution concentration. Plackett-Burman design was used to screen the main factors and Box-Behnken response surface was led to find a model for optimizing the response. The optimized membrane electrode shows a Nernstian slope for chromium (III) ions over a wide linear range from 1.99x10(-6) to 3.16x10(-2)molL(-1) and a slope of 19.5+/-0.1mVdecade(-1) of activity. It would be successfully applied in the pH range from 3.5 to 6.5 with detection limit of 1.77x10(-6)molL(-1) (0.092mgL(-1)). The response time of the sensor is about 8s and the membrane can be used for more than 6 weeks without any deviation. The relative standard deviations (R.S.D.) for six replicate the measurements of 1.0x10(-4) and 1.0x10(-3)molL(-1) of Cr(III) were 3.2 and 3%, respectively. The electrode revealed comparatively good selectivity with respect to many cations including alkali earth, transition and heavy metal ions. The electrode was successfully used as an indicator in the potentiometric titration of Cr(III) with EDTA and was also applied to the direct determination chromium (III) content of spiked water and soil samples.

Ultra violet resonance Raman spectroscopy in lignin analysis: determination of characteristic vibrations of p-hydroxyphenyl, guaiacyl, and syringyl lignin structures.

Science.gov (United States)

Saariaho, Anna-Maija; Jääskeläinen, Anna-Stiina; Nuopponen, Mari; Vuorinen, Tapani

2003-01-01

Raman spectroscopy of wood and lignin samples is preferably carried out in the near-infrared region because lignin produces an intense laser-induced fluorescence background at visible excitation wavelengths. However, excitation of aromatic and conjugated lignin structures with deep ultra violet (UV) light gives resonance-enhanced Raman signals while the overlapping fluorescence is eliminated. In this study, ultra violet resonance Raman (UVRR) spectroscopy was used to define characteristic vibration bands of model compounds of p-hydroxyphenyl, guaiacyl, and syringyl lignin structures at three excitation wavelengths (229, 244, and 257 nm). The intensities of each band, relative to the intensity of the aromatic vibration band at 1600 cm-1, were defined and the most suitable excitation wavelength was suggested for each structure. p-Hydroxyphenyl structures showed intensive characteristic bands at 1217-1214 and 1179-1167 cm-1 with excitation at 244 nm, whereas the bands of guaiacyl structures were more intensive with 257 nm excitation. Most intensive characteristic bands of guaiacyl structures were found at 1289-1279, 1187-1185, 1158-1155, and 791-704 cm-1. Syringyl structures had almost identical spectra with 244 and 257 nm excitations with characteristic bands at 1514-1506, 1333-1330, and 981-962 cm-1. The characteristic bands of the three structural units were also found from the compression wood, softwood, and hardwood samples, indicating that UVRR spectroscopy can be applied for the determination of chemical structures of lignin.

Adsorptive removal of crystal violet dye by a local clay and process optimization by response surface methodology

Science.gov (United States)

Loqman, Amal; El Bali, Brahim; Lützenkirchen, Johannes; Weidler, Peter G.; Kherbeche, Abdelhak

2017-11-01

The current study relates to the removal of a dye [crystal violet (CV)] from aqueous solutions through batch adsorption experiment onto a local clay from Morocco. The clay was characterized by X-ray diffraction, IR spectroscopy, X-ray fluorescence, scanning electron microscope, Brunauer-Emmett-Teller analysis and Fraunhofer diffraction method. The influence of independent variables on the removal efficiency was determined and optimized by response surface methodology using the Box-Behnken surface statistical design. The model predicted maximum adsorption of 81.62% under the optimum conditions of operational parameters (125 mg L-1 initial dye concentration, 2.5 g L-1 adsorbent dose and time of 43 min). Practically, the removal ranges in 27.4-95.3%.

Suburban immigrants to wildlands disrupt honest signaling in ultra-violet plumage

Directory of Open Access Journals (Sweden)

Angela Tringali

2015-06-01

Full Text Available Urbanization changes habitat in a multitude of ways, including altering food availability. Access to human-provided food can change the relationship between body condition and honest advertisements of fitness, which may result in changes to behavior, demography, and metapopulation dynamics. We compared plumage color, its relationship with body condition and feather growth, and use as signal of dominance between a suburban and a wildland population of Florida Scrub-Jay (Aphelocoma coerulescens. Although plumage color was not related to body condition at either site, suburban birds had plumage with a greater proportion of total reflectance in the ultra-violet (UV and peak reflectance at shorter wavelengths. Despite the use of plumage reflectance as a signal of dominance among individuals in the wildlands, we found no evidence of status signaling at the suburban site. However, birds emigrating from the suburban site to the wildland site tended to be more successful at acquiring breeder status but less successful at reproducing than were immigrants from an adjacent wildland site, suggesting that signaled and realized quality differ. These differences in signaling content among populations could have demographic effects at metapopulation scales and may represent an evolutionary trap whereby suburban immigrants are preferred as mates even though their reproductive success relative to effort is lower.

Elimination of root-infecting pathogens in recirculation water from closed cultivation systems by ultra-violet radiation

International Nuclear Information System (INIS)

Runia, W.T.

1994-01-01

The development from growing in border soil to soilless cultures has not resulted in the disappearance of soil-borne diseases. Most root-infecting pathogens also occur in these new cultivation systems. Some pathogens such as Pythium, Phytophthora, cucumber green mottle mosaic virus and tomato mosaic virus are easily transmitted in recirculation water as is Olpidium, the vector of several viruses. To exclude any risk of dispersal of plant pathogens the water has to be sterilised before re-use. Rainwater collected from the glasshouse roof can also be contaminated with pathogens. When this rainwater is used for irrigation water it should be disinfected first. Currently water disinfection by heating or ozonisation is applied on some 450 nurseries. Initially ultra-violet(UV) radiation was not effective against plant pathogens. Only at a low capacity of 18 l h -1 and a high UV-dose of 430 mJ cm -2 could fungal spores be eliminated in nutrient solution. A low capacity however implies a poor turbulence in the water, resulting in varying UV-doses in the different water layers. Two new UV-installations with high capacities were tested for their efficacy against fungal and viral plant pathogens. One installation was equipped with a high-pressure and the other with a low-pressure mercury vapour lamp. In both installations a sandfilter first removed organic particles from the water. A UV-dose from the high-pressure lamp of 28 mJ cm -2 reduced the infectivity of conidia of Fusarium oxysporum f.sp lycopersici by 90 % resulting in a 99.9 % reduction at 84 mJ cm -2 . The low-pressure lamp completely eliminated conidia of Fusarium at a UV-dose of 70 mJ cm -2 . Tomato mosaic virus was reduced by 99 % using a UV-dose of 100 mJ cm -2 in both installations. Ultra-violet radiation can be effective against plant pathogens providing the dose under controlled conditions is sufficient. Numerous growers use UV-radiation for the disinfection of water in closed cultivation systems. (author)

Chemically Modified Polyvinyl Chloride for Removal of Thionine Dye (Lauth’s Violet

Directory of Open Access Journals (Sweden)

Helena Ma A. M. M. S. Ali

2017-11-01

Full Text Available The chemical modification of hydrophobic polymer matrices is an alternative way to elchange their surface properties. The introduction of sulfonic groups in the polymer changes the surface properties such as adhesion, wettability, catalytic ability, and adsorption capacity. This work describes the production and application of chemically modified polyvinyl chloride (PVC as adsorbent for dyes removal. Chemical modification of PVC was evaluated by infrared spectroscopy and elemental analysis, which indicated the presence of sulfonic groups on PVC. The chemically modified PVC (PVCDS showed an ion exchange capacity of 1.03 mmol−1, and efficiently removed the thionine dye (Lauth’s violet from aqueous solutions, reaching equilibrium in 30 min. The adsorption kinetics was better adjusted for a pseudo second order model. This result indicates that the adsorption of thionine onto PVCDS occurs by chemisorption. Among the models for the state of equilibrium, SIPS and Langmuir exhibited the best fit to the experimental results and PVCDS showed high adsorption capacities (370 mg−1. Thus, it is assumed that the system presents homogeneous characteristics to the distribution of active sites. The modification promoted the formation of surface characteristics favorable to the dye adsorption by the polymer.

Ultra-violet resonance Raman spectroscopy for the rapid discrimination of urinary tract infection bacteria.

Science.gov (United States)

Jarvis, Roger M; Goodacre, Royston

2004-03-19

The ability to identify pathogenic organisms rapidly provides significant benefits to clinicians; in particular, with respect to best prescription practices and tracking of recurrent infections. Conventional bioassays require 3-5 days before identification of an organism can be made, thus compromising the effectiveness with which patients can be treated for bacterial infections. We analysed 20 clinical isolates of urinary tract infections (UTI) by ultra-violet resonance Raman (UVRR) spectroscopy, utilising 244 nm excitation delivering approximately 0.1 mW laser power at the sample, with typical spectral collection times of 120 s. UVRR results in resonance-enhanced Raman signals for certain chromophoric segments of macromolecules, intensifying those selected bands above what would otherwise be observed for a normal Raman experiment. Utilising the whole-organism 'fingerprints' obtained by UVRR we were able to discriminate successfully between UTI pathogens using chemometric cluster analyses. This work demonstrates significant improvements in the speed with which spectra can be obtained by Raman spectroscopic techniques for the discrimination of clinical bacterial samples.

Spectroscopic characterizations of individual single-crystalline GaN nanowires in visible/ultra-violet regime.

Science.gov (United States)

Wu, Chien-Ting; Chu, Ming-Wen; Chen, Li-Chyong; Chen, Kuei-Hsien; Chen, Chun-Wei; Chen, Cheng Hsuan

2010-10-01

Spectroscopic investigations of individual single-crystalline GaN nanowires with a lateral dimensions of approximately 30-90nm were performed using the spatially resolved technique of electron energy-loss spectroscopy in conjunction with scanning transmission electron microscope showing a 2-A electron probe. Positioning the electron probe upon transmission impact and at aloof setup with respect to the nanomaterials, we explored two types of surface modes intrinsic to GaN, surface exciton polaritons at approximately 8.3eV (approximately 150nm) and surface guided modes at 3.88eV (approximately 320nm), which are in visible/ultra-violet spectral regime above GaN bandgap of approximately 3.3eV (approximately 375nm) and difficult to access by conventional optical spectroscopies. The explorations of these electromagnetic resonances might expand the current technical interests in GaN nanomaterials from the visible/UV range below approximately 3.5eV to the spectral regime further beyond.

Highly stable colloidal TiO{sub 2} nanocrystals with strong violet-blue emission

Energy Technology Data Exchange (ETDEWEB)

Ghamsari, Morteza Sasani, E-mail: msghamsari@yahoo.com [Laser & Optics Research School, NSTRI, 11155-3486 Tehran (Iran, Islamic Republic of); Gaeeni, Mohammad Reza [Laser & Optics Research School, NSTRI, 11155-3486 Tehran (Iran, Islamic Republic of); Han, Wooje; Park, Hyung-Ho [Department of Materials Science and Engineering, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-749 (Korea, Republic of)

2016-10-15

Improved sol–gel method has been applied to prepare highly stable colloidal TiO{sub 2} nanocrystals. The synthesized titania nanocrystals exhibit strong emission in the violet-blue wavelength region. Very long evolution time was obtained by preventing the sol to gel conversion with reflux process. FTIR, XRD, UV–vis absorption, photoluminescence and high resolution transmission electron microscope (HRTEM) were used to study the optical properties, crystalline phase, morphology, shape and size of prepared TiO{sub 2} colloidal nanocrystals. HRTEM showed that the diameter of TiO{sub 2} colloidal nanocrystals is about 5 nm. Although the PL spectra show similar spectral features upon excitation wavelengths at 280, 300 and 350 nm, but their emission intensities are significantly different from each other. Photoluminescence quantum yield for TiO{sub 2} colloidal nanocrystals is estimated to be 49% with 280 nm excitation wavelength which is in agreement and better than reported before. Obtained results confirm that the prepared colloidal TiO{sub 2} sample has enough potential for optoelectronics applications.

DIAGRAMME TRC ET STRUCTURES DE TREMPE ET DE REVENU D'UN ACIER FAIBLEMENT ALLIE AU MANGANESE-CHROME

Directory of Open Access Journals (Sweden)

Z LAROUK

2008-06-01

Full Text Available Cette étude concerne un acier faiblement allié au manganèse et chrome. L’utilisation principale de cet acier est la fabrication des tubes sans soudure, employés pour le forage ou le transport pétrolier. Les tubes traités thermiquement doivent supporter d’importantes contraintes de tension et de compression, sans risque de rupture. Les tubes trempés à l’eau souffrent d’une hétérogénéité structurale impliquant une diminution de dureté à la surface interne. Le but de cette étude est de déterminer les structures de l’acier après différents types de traitements, au cours de refroidissement continus dans les conditions industrielles de trempe (930°C et de revenu (670°C. Les résultats montrent que la vitesse critique de trempe est de 50°C/sec et, pour éviter la formation de la ferrite, une vitesse plus grande que 12°C/sec est nécessaire. Cet acier a une bonne trempabilité (11mm. La décroissance de la dureté de la martensite revenue est remarquable lorsque la température atteint 600°C.

Aminoquinolone WR6026 as a feasible substitute for gentian violet in Chagas' disease prophylaxis in preserved blood for transfusional purposes

Directory of Open Access Journals (Sweden)

Moraes-Souza Helio

2002-01-01

Full Text Available The search for a colorless, nontoxic and efficient drug to prevent transfusion-associated Chagas' disease (TACD has been underway unsuccessfully since 1953 when gentian violet was preconized and to date is still being used as the only in vitro trypanocidal agent. The recent findings of aminoquinolone "WR6026" as a trypanocidal agent, led the authors to study the metabolism of red cells stored with this compound, the main objective of which was to define its applicability in TACD control. Ten units of human whole blood collected in CPDA-1 were divided into two equal satellite bags. One had "WR6026" (final concentration 62.5µg/mL added and the other was used as a control, both were stored at 4ºC. At baseline, day 7, 14, 21 and 28, samples were taken for the following measurements: adenosine triphosphate (ATP, hemoglobin, electrolytes (sodium and potassium, gases (pO2 and pCO2 and osmotic fragility. The results of tests and control were analyzed through parametric t-student test. The results were similar in both groups throughout the experiment except for the level of ATP on day 14, which presented significantly higher values in the tests when compared with the controls (p = 0.012. It was concluded that WR6026 does not interfere in the preservation and probably the viability of the erythrocytes also until day 28 of storage. Consequently the authors suggest that WR6026 could emerge as a colorless substitute for gentian violet in the control of TACD in endemic areas.

The use of vapour phase ultra-violet spectroscopy for the analysis of arson accelerants in fire scene debris.

Science.gov (United States)

McCurdy, R J; Atwell, T; Cole, M D

2001-12-01

A method has been developed for the analysis of arson accelerants in fire scene debris by vapour phase ultra-violet (UV) spectroscopy. The method is rapid, inexpensive, simple to use and is sufficiently sensitive and discriminating to be of use for the analysis of crime scene samples. Application to casework samples is described. On occasion, the method offers additional information to that which can be obtained by gas chromatography-flame ionisation detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS) and represents a useful adjunct to these techniques. In addition, the method offers advantages where the use of GC-MS analysis of arson accelerants in fire scene debris is not a practical proposition.

An Unusual Dimeric Inhibitor of Acetylcholinesterase: Cooperative Binding of Crystal Violet

Directory of Open Access Journals (Sweden)

Anders Allgardsson

2017-08-01

Full Text Available Acetylcholinesterase (AChE is an essential enzyme that terminates cholinergic transmission by a rapid hydrolysis of the neurotransmitter acetylcholine. AChE is an important target for treatment of various cholinergic deficiencies, including Alzheimer’s disease and myasthenia gravis. In a previous high throughput screening campaign, we identified the dye crystal violet (CV as an inhibitor of AChE. Herein, we show that CV displays a significant cooperativity for binding to AChE, and the molecular basis for this observation has been investigated by X-ray crystallography. Two monomers of CV bind to residues at the entrance of the active site gorge of the enzyme. Notably, the two CV molecules have extensive intermolecular contacts with each other and with AChE. Computational analyses show that the observed CV dimer is not stable in solution, suggesting the sequential binding of two monomers. Guided by the structural analysis, we designed a set of single site substitutions, and investigated their effect on the binding of CV. Only moderate effects on the binding and the cooperativity were observed, suggesting a robustness in the interaction between CV and AChE. Taken together, we propose that the dimeric cooperative binding is due to a rare combination of chemical and structural properties of both CV and the AChE molecule itself.

Small particle reagent based on crystal violet dye for developing latent fingerprints on non-porous wet surfaces

Directory of Open Access Journals (Sweden)

Richa Rohatgi

2015-12-01

Full Text Available Small particle reagent (SPR is a widely used method for developing latent fingerprints on non-porous wet surfaces. SPR based on zinc carbonate hydroxide monohydrate, ZnCo3·2Zn(OH2·H2O – also called basic zinc carbonate – has been formulated. The other ingredients of the formulation are crystal violet dye and a commercial liquid detergent. The composition develops clear, sharp and detailed fingerprints on non-porous items, after these were immersed separately in clean and dirty water for variable periods of time. The ability of the present formulation to detect weak and faint chance prints not only enhances its utility, but also its potentiality in forensic case work investigations. The raw materials used to prepare the SPR are cost-effective and non-hazardous.

A High Power InGaN-Based Blue-Violet Laser Diode Array with a Broad-Area Stripe

International Nuclear Information System (INIS)

Chen Ping; Zhao De-Gang; Feng Mei-Xin; Jiang De-Sheng; Liu Zong-Shun; Yang Hui; Zhang Li-Qun; Li De-Yao; Liu Jian-Ping; Wang Hui; Zhu Jian-Jun; Zhang Shu-Ming; Zhang Bao-Shun

2013-01-01

An array of high power InGaN/GaN multi-quantum-well laser diodes with a broad waveguide is fabricated. The laser diode structure is grown on a GaN substrate by metal-organic chemical vapor deposition. The laser diode array consists of five emitter stripes which share common electrodes on one laser chip. The electrical and optical characteristics of the laser diode array are investigated under the pulse current injection with 10kHz frequency and 100 ns pulse width. The laser diode array emits at the wavelength of 409 nm, which is located in the blue-violet region, and the threshold current is 2.9 A. The maximum output light peak power is measured to be 7.5 W at the wavelength of 411.8 nm under the current of 25 A

Adsorption of crystal violet with diatomite earth&carbon by a modification of hydrothermal carbonization process.

Science.gov (United States)

Zhang, Yanzhuo; Li, Jun; Chen, Guanghui; Bian, Wei; Lu, Yun; Li, Wenjing; Zheng, Zhaoming; Cheng, Xiaojie

2016-01-01

The high colority and difficulty of decolorization are the most important tasks on printing and dyeing wastewater. This study investigates the ability of diatomite earth&carbon (DE&C) as an adsorbent to removal crystal violet (CV) from aqueous solutions. Fourier transform infrared spectroscopy results indicate the importance of functional groups during the adsorption of CV. The obtained N2 adsorption-desorption isotherm values accord with well IUPAC type II. Our calculations determined a surface area of 73.15 m(2) g(-1) for DE&C and an average pore diameter of 10.56 nm. Equilibrium data of the adsorption process fitted very well to the Langmuir model (R(2) > 0.99). The results of kinetics study showed that the pseudo-second-order model fitted to the experimental data well. The thermodynamic parameters were also evaluated. ΔH° 0 and ΔG° < 0 demonstrated that the adsorption process was spontaneous and exothermic for dye. Furthermore the positive value of ΔS° reflected good affinity of the CV dye.

40 CFR 415.341 - Specialized definitions.

Science.gov (United States)

2010-07-01

... AND STANDARDS INORGANIC CHEMICALS MANUFACTURING POINT SOURCE CATEGORY Chrome Pigments Production... shall apply to this subpart. (b) The term chrome pigments means chrome yellow, chrome orange, molybdate... means chrome pigments. ...

Development of electrochemiluminescent inhibition method for determination of gentian violet in aquatic water.

Science.gov (United States)

Wang, Sui; Hao, Tingting; Yu, Xinwei; Gai, Panpan; Guo, Zhiyong

2012-04-01

Gentian violet (GV) was found to quench the electrochemiluminescence (ECL) of the tris(2,2'-bipyridyl)ruthenium(II)/tris-n-propylamine (Ru(bpy)3(2+)-TPA) system at a glass carbon electrode (GCE). Based on the ECL signal changes, a simple and ultrasensitive detection method for GV in aquatic water was established. Under the optimized conditions, the quenched ECL intensity versus the logarithm of the concentration of GV was linear over a concentration range from 1.0×10(-10) to 5.0×10(-7) mol L(-1), and the limit of detection (LOD) was found to be 4.5×10(-12) mol L(-1) (S/N=3). The results obtained by the ECL system were better than other reported methods in literatures in terms of sensitivity or linear response range. The method was successfully applied to determine GV in aquatic water, and the relative standard deviations (RSDs) were found less than 6.3%, and the recoveries were obtained from 98.7 to 111.0%. Moreover, a possible mechanism of the quenching effect was primarily discussed based on UV-visible absorption spectra, cyclic voltammograms and IECL-E curves. Copyright © 2011 Elsevier B.V. All rights reserved.

The compatibility of chromium-aluminium steels with high pressure carbon dioxid at intermediate- temperatures; Compatibilite des aciers au chrome-aluminium avec le gaz carbonique sous pression aux temperatures moyennes

Energy Technology Data Exchange (ETDEWEB)

Leclercq, D; Loriers, H; David, R; Darras, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

With a view to their use in the exchangers of nuclear reactors of the graphite-gas or heavy water-gas types, the behaviour of chromium-aluminium steels containing up to 7 per cent chromium and 1.5 per cent aluminium has been studied in the presence of high-pressure carbon dioxide at temperatures of between 400 and 700 deg. C. The two most interesting grades of steel (2 per cent Cr - 0.35 per cent Al - 0.35 per cent Mo and 7 per cent Cr - 1.5 per cent Al - 0.6 per cent Si) are still compatible with carbon dioxide up to 550 and 600 deg. C respectively. A hot dip aluminised coating considerably increases resistance to oxidation of the first grade and should make possible its use up to temperatures of at least 600 deg. C. (authors) [French] Dans l'optique de leur emploi dans les echangeurs de reacteurs nucleaires des filieres graphite-gaz ou eau lourde-gaz, le comportement en presence de gaz carbonique sous pression d'aciers au chrome-aluminium, contenant jusqu'a 7 pour cent de chrome et 1,5 pour cent d'aluminium a ete etudie entre 400 et 700 deg. C. Les deux nuances les plus interessantes (2 pour cent Cr - 0,35 pour cent Al - 0,35 pour cent Mo et 7 pour cent Cr - 1,5 pour cent Al - 0,6 pour cent Si) restent compatibles avec le gaz carbonique jusqu'a 550 et 600 deg. C respectivement. Un revetement d'aluminium, effectue par immersion dans un bain fondu, ameliore notablement la resistance a l'oxydation de la premiere et doit permettre son empioi jusqu'a 600 deg. C au moins. (auteurs)

ZnO-nanorod-array/p-GaN high-performance ultra-violet light emitting devices prepared by simple solution synthesis

Science.gov (United States)

Jha, Shrawan Kumar; Luan, Chunyan; To, Chap Hang; Kutsay, Oleksandr; Kováč, Jaroslav; Zapien, Juan Antonio; Bello, Igor; Lee, Shuit-Tong

2012-11-01

Pure ultra-violet (UV) (378 nm) electroluminescence (EL) from zinc oxide (ZnO)-nanorod-array/p-gallium nitride (GaN) light emitting devices (LEDs) is demonstrated at low bias-voltages (˜4.3 V). Devices were prepared merely by solution-synthesis, without any involvement of sophisticated material growth techniques or preparation methods. Three different luminescence characterization techniques, i.e., photo-luminescence, cathodo-luminescence, and EL, provided insight into the nature of the UV emission mechanism in solution-synthesized LEDs. Bias dependent EL behaviour revealed blue-shift of EL peaks and increased peak sharpness, with increasing the operating voltage. Accelerated bias stress tests showed very stable and repeatable electrical and EL performance of the solution-synthesized nanorod LEDs.

Strong violet-blue light photoluminescence emission at room temperature in SrZrO3: Joint experimental and theoretical study

International Nuclear Information System (INIS)

Longo, V.M.; Cavalcante, L.S.; Erlo, R.; Mastelaro, V.R.; Figueiredo, A.T. de; Sambrano, J.R.; Lazaro, S. de; Freitas, A.Z.; Gomes, L.; Vieira, N.D.; Varela, J.A.; Longo, Elson

2008-01-01

Ultrafine ordered and disordered SrZrO 3 powders were prepared by the polymeric precursor method. The structural evolution from structural disorder to order was monitored by X-ray diffraction and X-ray absorption near-edge spectroscopy. Complex cluster vacancies [ZrO 5 .V O Z ]and[SrO 11 .V O Z ] (where V O Z =V O X , V O · andV O ·· ) were proposed for disordered powders. The intense violet-blue light photoluminescence emission measured at room temperature in the disordered powders was attributed to complex cluster vacancies. High-level quantum mechanical calculations within the density functional theory framework were used to interpret the experimental results

Effect of Ducks Yolk and Formic Acid in Fat Liquoring Process on the Physical Quality of Broiler Chicken Shank Chrome Tanning

Directory of Open Access Journals (Sweden)

Mustakim Mustakim

2017-07-01

Full Text Available The purpose of this study was to find out the effect of ducks yolk and formic acid in fat liquoring process of the tanned skin.  The materials used in this study were 30 pieces of 7 weeks of broiler chicken shank. The study was carried out using completely randomized design. The variables measured were softness, tensile strength and stretch of the tanned skin. Data were analyzed by analysis of variance and followed by Duncan’s Multiple Range Test. The research results showed that the addition of ducks yolk and formic acid didn’t gave significantly affect on the softness (p>0.05, while gave highly significant affect on tensile strength and stretch (p0.05 on the softness and stretch, and have significantly (p<0.05 on the tensile strength of leather. The conclusion of this research the addition of 11% duck yolk and 1% formic acid in fat liquoring is the best treatment for broiler chicken shank chrome tanning on the skin softness (2,667, tensile strength (135,707 kg/cm2, and stretch (37,34%, respectively.

Insight into biosorption equilibrium, kinetics and thermodynamics of crystal violet onto Ananas comosus (pineapple) leaf powder

Science.gov (United States)

Chakraborty, Sagnik; Chowdhury, Shamik; Saha, Papita Das

2012-06-01

Biosorption performance of pineapple leaf powder (PLP) for removal of crystal violet (CV) from its aqueous solutions was investigated. To this end, the influence of operational parameters such as pH, biosorbent dose, initial dye concentration and temperature were studied employing a batch experimental setup. The biosorption process followed the Langmuir isotherm model with high correlation coefficients ( R 2 > 0.99) at different temperatures. The maximum monolayer biosorption capacity was found to be 78.22 mg g-1 at 293 K. The kinetic data conformed to the pseudo-second-order kinetic model. The activation energy of the system was calculated as 58.96 kJ mol- 1 , indicating chemisorption nature of the ongoing biosorption process. A thermodynamic study showed spontaneous and exothermic nature of the biosorption process. Owing to its low cost and high dye uptake capacity, PLP has potential for application as biosorbent for removal of CV from aqueous solutions.

Quantitative super-resolution localization microscopy of DNA in situ using Vybrant® DyeCycle™ Violet fluorescent probe

Directory of Open Access Journals (Sweden)

Dominika Żurek-Biesiada

2016-06-01

Full Text Available Single Molecule Localization Microscopy (SMLM is a recently emerged optical imaging method that was shown to achieve a resolution in the order of tens of nanometers in intact cells. Novel high resolution imaging methods might be crucial for understanding of how the chromatin, a complex of DNA and proteins, is arranged in the eukaryotic cell nucleus. Such an approach utilizing switching of a fluorescent, DNA-binding dye Vybrant® DyeCycle™ Violet has been previously demonstrated by us (Żurek-Biesiada et al., 2015 [1]. Here we provide quantitative information on the influence of the chemical environment on the behavior of the dye, discuss the variability in the DNA-associated signal density, and demonstrate direct proof of enhanced structural resolution. Furthermore, we compare different visualization approaches. Finally, we describe various opportunities of multicolor DNA/SMLM imaging in eukaryotic cell nuclei.

Study of the quenching and subsequent return to room temperature of uranium-chromium, uranium-iron, and uranium-molybdenum alloys containing only small amounts of the alloying element; Etude de la trempe et du revenu a la temperature ordinaire d'alliages uranium-chrome, uranium-fer et uranium-molybdene, a faible teneur en element d'alliage

Energy Technology Data Exchange (ETDEWEB)

Delaplace, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1960-09-15

/s. He has however observed the formation of several martensitic structures. (author) [French] Grace a un appareillage qui permet d'effectuer les traitements thermiques prealables sous vide, de conduire la trempe dans une atmosphere d'argon tres pur et d'enregistrer a la fois les courbes de refroidissement temperature-temps et la courbe dilatometrique, l'auteur a etudie les transformations que subissent les alliages uranium-chrome, uranium-fer et uranium-molybdene pendant leur trempe et leur revenu ulterieur a la temperature ordinaire. Dans les alliages uranium-chrome et uranium-fer, la temperature de debut de la transformation {gamma} {yields} {beta} varie tres peu avec la vitesse de refroidissement. Dans les alliages uranium-molybdene a 2,8 at. Mo pour cent, elle est abaissee de 120 deg. C pour une vitesse de refroidissement de 500 deg. C/minute. La temperature de debut de la transformation {beta} {yields} {alpha} est abaissee de 170 deg. C pour une vitesse de refroidissement de 500 deg. C/minute dans l'alliage uranium-chrome a 0,37 at. Cr pour cent. Elle est assez peu modifiee dans le cas des alliages uranium-fer. L'addition de chrome ou de fer permet de retenir la forme {beta} a la temperature ordinaire par trempe depuis les domaines {beta} et {gamma}. Particulierement instable, la phase {beta} se transforme en aiguilles {alpha}, des la temperature ordinaire, suivant une loi de transformation autocatalytique analogue a la loi de transformation martensique de l'austenite dans le cas du chrome et a la loi de transformation bainitique de l'austenite dans le cas du fer. La phase {beta} obtenue par trempe depuis le domaine {beta} est plus stable que celle que l'on retient par trempe depuis le domaine {gamma}. Le chrome est un stabilisant de la phase {beta} plus efficace que le fer. Malheureusement il provoque une fissuration importante. La transformation {beta} {yields} {alpha} des alliages uranium-chrome a la temperature ordinaire a ete enregistree par

[Flotation spectrophotometric determination of copper on isochromatic dye ion pair with crystal violet and bromopnenol blue].

Science.gov (United States)

Liu, B; Chen, C; Zuo, B

1999-02-01

Bromophenol blue (BPB) was produced and entered into the aqueous phase when NaOH solution of pH = 10 was added to Cu(biq)2BPB by trichloromethane and isoamyl alcohol (20:1) extractive. And then CV x BPB was floated by crystal violet (CV) with benzene solution. The flotation was dissolved in ethanol and the absorbance of the solution measured at 590 nm. The sensitivity was raised because of the two dyes assistant effect. The molar absorptivity was 1.45 x 10(5) L x mol(-1) x cm(-1). Copper in the sample was separated first by extracting the Cu(biq)2BPB complex with trichloromethane and isoamyl alcohol, thus achieving a high selectivity. Beer's law was obeyd in the range of 0-0. 4 mg/L with a relative standard deviation of 3.6%. For 4.8 x 10(-8) g/mL copper solution, the recoveries were 97.8%-101.7%.

Magnetic property variation in carbon steel and chrome-molybdenum steel as a function of uniaxial stress noncoaxial with the magnetic field (abstract)

International Nuclear Information System (INIS)

Sablik, M.J.; Kaminski, D.A.; Jiles, D.C.; Biner, S.B.

1993-01-01

Magnescope 1 magnetic measurements were made on carbon steel specimens ranging from 0.1--0.8 wt %C and on chrome-molybdenum steel specimens cut from electric power plant pipes previously in service. The carbon steel specimens were heat-treated using three procedures: (1) spheroidization, (2) quenching, and (3) quench and tempering. The specimens were subjected to uniaxial tension up to 40 ksi. The inspection head was aligned so that the magnetic field was oriented at different angles with respect to the stress axis. Magnetic properties (such as coercivity and maximum differential permeability) were extracted from digitized magnetic hysteresis loop measurements. Magnetic properties were studied as a function of stress at each angle of stress-field orientation. To our knowledge, such a comprehensive study of noncoaxial stress and field effects has never been accomplished before for such a wide variety of steel specimens. Results for the various materials are presented for different orientation angles and compared to numerical results from the noncoaxial magnetomechanical hysteresis model of Sablik et al. 2

Simulation and optimization of deep violet InGaN double quantum well laser

Science.gov (United States)

Alahyarizadeh, Gh.; Ghazai, A. J.; Rahmani, R.; Mahmodi, H.; Hassan, Z.

2012-03-01

The performance characteristics of a deep violet InGaN double quantum well laser diode (LD) such as threshold current ( Ith), external differential quantum efficiency (DQE) and output power have been investigated using the Integrated System Engineering Technical Computer Aided Design (ISE-TCAD) software. As well as its operating parameters such as internal quantum efficiency ( ηi), internal loss ( αi) and transparency threshold current density ( J0) have been studied. Since, we are interested to investigate the mentioned characteristics and parameters independent of well and barrier thickness, therefore to reach a desired output wavelength, the indium mole fraction of wells and barriers has been varied consequently. The indium mole fractions of well and barrier layers have been considered 0.08 and 0.0, respectively. Some important parameters such as Al mole fraction of the electronic blocking layer (EBL) and cavity length which affect performance characteristics were also investigated. The optimum values of the Al mole fraction and cavity length in this study are 0.15 and 400 μm, respectively. The lowest threshold current, the highest DQE and output power which obtained at the emission wavelength of 391.5 nm are 43.199 mA, 44.99% and 10.334 mW, respectively.

Maximum material thickness for extreme ultra-violet and X-ray backlighter probing of dense plasma

International Nuclear Information System (INIS)

Huang, H.; Tallents, G.J.

2008-01-01

Extreme ultra-violet (EUV) lasers, X-ray lasers and other backlighter sources can be used to probe high-energy density materials if their brightness can overcome self-emission from the material. We investigate the maximum plasma thickness of aluminum, silicon and iron that can be probed with EUV or X-ray photons of energy 89-1243 eV before self-emission from the plasma overwhelms the backlighter output. For a uniform plasma, backlighter transmission decreases exponentially with increasing thickness of the material following Beer's law at a rate dependent on the plasma opacity. We evaluate the plasma opacity with the Los Alamos TOPS opacity data. The self-emission is assumed to be either that of a black body to arise from a plasma in LTE or to only consist of free-free and free-bound emission. It is shown that at higher plasma temperature (≥40 eV), EUV radiation (e.g. photon energy=89 eV) can probe a greater thickness of plasma than X-ray radiation (e.g. photon energy=1243 eV)

Flow analysis methods for the direct ultra-violet spectrophotometric measurement of nitrate and total nitrogen in freshwaters

Energy Technology Data Exchange (ETDEWEB)

Gentle, Brady S.; Ellis, Peter S.; Grace, Michael R. [Water Studies Centre, School of Chemistry, Monash University, Victoria 3800 (Australia); McKelvie, Ian D., E-mail: iandm@unimelb.edu.au [School of Chemistry, University of Melbourne, Victoria 3010 (Australia); School of Geography, Earth and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

2011-10-17

Highlights: {yields} Second derivative UV spectrophotometry has been used to determine nitrate and total N using flow analysis techniques. {yields} A simple flow system with a single-reflection flow-through cell was used for the UV measurement of nitrate. {yields} Total N was determined after on-line UV photooxidation with alkaline peroxodisulfate. {yields} Analyses carried out using the developed flow systems show a high degree of agreement with comparative analyses. {yields} This method requires no colorimetric reagents and eliminates the requirement for a toxic cadmium reduction column. - Abstract: Second derivative ultra-violet spectrophotometric methods are described for the measurement of nitrate and total nitrogen in freshwaters using flow analysis techniques. A simple flow system consisting of a peristaltic pump and a single-reflection flow-through cell was used for the measurement of nitrate. Quantification of total nitrogen using alkaline peroxodisulfate photo-digestion was achieved by incorporating an ultra-violet photo-reactor, a hollow-fibre filter and a debubbler into the flow system. The nitrate system featured a limit of detection of 0.04 mg N L{sup -1}, 0.4%RSD (1 mg N L{sup -1} as nitrate, n = 10), a coefficient of determination (R{sup 2}) of 0.9995 over the calibration range 0.0-2.0 mg N L{sup -1}, and a data acquisition time of 1.5 s per spectrum. The total nitrogen system featured a limit of detection of 0.05 mg N L{sup -1}, 1%RSD (1 mg N L{sup -1} as ammonium chloride, n = 10), a coefficient of determination of 0.9989 over the calibration range 0.0-2.0 mg N L{sup -1}, and a throughput of 5 sample h{sup -1} measured in triplicate. Digestions of five model nitrogen compounds returned recoveries of >88%. Determinations carried out using the developed systems show a high degree of agreement with data obtained using reference methods. These methods require no colorimetric reagents and eliminate the requirement for a toxic cadmium reduction column

Flow analysis methods for the direct ultra-violet spectrophotometric measurement of nitrate and total nitrogen in freshwaters

International Nuclear Information System (INIS)

Gentle, Brady S.; Ellis, Peter S.; Grace, Michael R.; McKelvie, Ian D.

2011-01-01

Highlights: → Second derivative UV spectrophotometry has been used to determine nitrate and total N using flow analysis techniques. → A simple flow system with a single-reflection flow-through cell was used for the UV measurement of nitrate. → Total N was determined after on-line UV photooxidation with alkaline peroxodisulfate. → Analyses carried out using the developed flow systems show a high degree of agreement with comparative analyses. → This method requires no colorimetric reagents and eliminates the requirement for a toxic cadmium reduction column. - Abstract: Second derivative ultra-violet spectrophotometric methods are described for the measurement of nitrate and total nitrogen in freshwaters using flow analysis techniques. A simple flow system consisting of a peristaltic pump and a single-reflection flow-through cell was used for the measurement of nitrate. Quantification of total nitrogen using alkaline peroxodisulfate photo-digestion was achieved by incorporating an ultra-violet photo-reactor, a hollow-fibre filter and a debubbler into the flow system. The nitrate system featured a limit of detection of 0.04 mg N L -1 , 0.4%RSD (1 mg N L -1 as nitrate, n = 10), a coefficient of determination (R 2 ) of 0.9995 over the calibration range 0.0-2.0 mg N L -1 , and a data acquisition time of 1.5 s per spectrum. The total nitrogen system featured a limit of detection of 0.05 mg N L -1 , 1%RSD (1 mg N L -1 as ammonium chloride, n = 10), a coefficient of determination of 0.9989 over the calibration range 0.0-2.0 mg N L -1 , and a throughput of 5 sample h -1 measured in triplicate. Digestions of five model nitrogen compounds returned recoveries of >88%. Determinations carried out using the developed systems show a high degree of agreement with data obtained using reference methods. These methods require no colorimetric reagents and eliminate the requirement for a toxic cadmium reduction column. The overlap of chloride and nitrate spectra in seawater is

An LED Approach for Measuring the Photocatalytic Breakdown of Crystal Violet Dye

Science.gov (United States)

Ryan, Robert E.; Underwood, Lauren W.; ONeal, Duane; Pagnutti, Mary; Davis, Bruce A.

2009-01-01

A simple technique to assess the reactivity of photocatalytic coatings sprayed onto transmissive glass surfaces was developed. This new method uses ultraviolet (UV) gallium nitride (GaN) light-emitting diodes (LEDs) to drive a photocatalytic reaction (the photocatalytic breakdown of a UV-resistant dye applied to a surface coated with the semiconductor titanium dioxide); and then a combination of a stabilized white light LED and a spectrometer to track the dye degradation as a function of time. Simple, standardized evaluation techniques that assess photocatalytic materials over a variety of environmental conditions, including illumination level, are not generally available and are greatly needed prior to in situ application of photocatalytic technologies. To date, much research pertaining to this aspect of photocatalysis has been limited and has focused primarily on laboratory experiments using mercury lamps. Mercury lamp illumination levels are difficult to control over large ranges and are temporally modulated by line power, limiting their use in helping to understand and predict how photocatalytic materials will behave in natural environmental settings and conditions. The methodology described here, using steady-state LEDs and time series spectroradiometric techniques, is a novel approach to explore the effect of UV light on the photocatalytic degradation of a UV resistant dye (crystal violet). GaN UV LED arrays, centered around 365 nm with an adjustable DC power supply, are used to create a small, spatially uniform light field where the steady state light level can be varied over three to four orders of magnitude. For this study, a set of glass microscope slides was custom coated with a thinly sprayed layer of photocatalytic titanium dioxide. Crystal violet was then applied to these titanium-dioxide coated slides and to uncoated control slides. The slides were then illuminated at various light levels from the dye side of the slide by the UV LED array. To monitor

Study of the quenching and subsequent return to room temperature of uranium-chromium, uranium-iron, and uranium-molybdenum alloys containing only small amounts of the alloying element; Etude de la trempe et du revenu a la temperature ordinaire d'alliages uranium-chrome, uranium-fer et uranium-molybdene, a faible teneur en element d'alliage

Energy Technology Data Exchange (ETDEWEB)

Delaplace, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1960-09-15

/s. He has however observed the formation of several martensitic structures. (author) [French] Grace a un appareillage qui permet d'effectuer les traitements thermiques prealables sous vide, de conduire la trempe dans une atmosphere d'argon tres pur et d'enregistrer a la fois les courbes de refroidissement temperature-temps et la courbe dilatometrique, l'auteur a etudie les transformations que subissent les alliages uranium-chrome, uranium-fer et uranium-molybdene pendant leur trempe et leur revenu ulterieur a la temperature ordinaire. Dans les alliages uranium-chrome et uranium-fer, la temperature de debut de la transformation {gamma} {yields} {beta} varie tres peu avec la vitesse de refroidissement. Dans les alliages uranium-molybdene a 2,8 at. Mo pour cent, elle est abaissee de 120 deg. C pour une vitesse de refroidissement de 500 deg. C/minute. La temperature de debut de la transformation {beta} {yields} {alpha} est abaissee de 170 deg. C pour une vitesse de refroidissement de 500 deg. C/minute dans l'alliage uranium-chrome a 0,37 at. Cr pour cent. Elle est assez peu modifiee dans le cas des alliages uranium-fer. L'addition de chrome ou de fer permet de retenir la forme {beta} a la temperature ordinaire par trempe depuis les domaines {beta} et {gamma}. Particulierement instable, la phase {beta} se transforme en aiguilles {alpha}, des la temperature ordinaire, suivant une loi de transformation autocatalytique analogue a la loi de transformation martensique de l'austenite dans le cas du chrome et a la loi de transformation bainitique de l'austenite dans le cas du fer. La phase {beta} obtenue par trempe depuis le domaine {beta} est plus stable que celle que l'on retient par trempe depuis le domaine {gamma}. Le chrome est un stabilisant de la phase {beta} plus efficace que le fer. Malheureusement il provoque une fissuration importante. La transformation {beta} {yields} {alpha} des alliages uranium-chrome a la temperature

Ultra-violet and visible absorption characterization of explosives by differential reflectometry.

Science.gov (United States)

Dubroca, Thierry; Moyant, Kyle; Hummel, Rolf E

2013-03-15

This study presents some optical properties of TNT (2,4,6-trinitrotoluene), RDX, HMX and tetryl, specifically their absorption spectra as a function of concentration in various solvents in the ultraviolet and visible portion of the electromagnetic spectrum. We utilize a standoff explosives detection method, called differential reflectometry (DR). TNT was diluted in six different solvents (acetone, acetonitrile, ethanol, ethyl acetate, methanol, and toluene), which allowed for a direct comparison of absorption features over a wide range of concentrations. A line-shape analysis was adopted with great accuracy (R(2)>0.99) to model the absorption features of TNT in differential reflectivity spectra. We observed a blue shift in the pertinent absorption band with decreasing TNT concentration for all solvents. Moreover, using this technique, it was found that for all utilized solvents the concentration of TNT as well as of RDX, HMX, and tetryl, measured as a function of the transition wavelength of the ultra-violet absorption edge in differential reflectivity spectra shows three distinct regions. A model is presented to explain this behavior which is based on intermolecular hydrogen bonding of explosives molecules with themselves (or lack thereof) at different concentrations. Other intermolecular forces such as dipole-dipole interactions, London dispersion forces and π-stacking contribute to slight variations in the resulting spectra, which were determined to be rather insignificant in comparison to hydrogen bonding. The results are aimed towards a better understanding of the DR spectra of explosives energetic materials. Copyright © 2012 Elsevier B.V. All rights reserved.

Internal residual strain mapping in carburized chrome molybdenum steel after quenching by neutron strain scanning

International Nuclear Information System (INIS)

Sakaida, Yoshihisa; Serizawa, Takanobu; Manzanka, Michiya

2011-01-01

A hollow circular cylinder specimen with an annular U-notch of chrome molybdenum steel with 0.20 mass% C (SCM420) was carburized in carrier gas and quenched in oil bath. In order to determine the case depth, the specimen was cut off and carbon content and Vickers hardness gradients were measured experimentally near the carburized surface. The residual strain mapping in the interior of carburized cylinder was conducted nondestructively by neutron strain scanning. In this study, the neutron diffraction from Fe-211 plane was used for strain scanning. The neutron wavelength was tuned to 0.1654nm so that diffraction angle became about 90deg. Radial, hoop and axial residual strains were measured by scanning diffracting volume along the axial direction of cylinder specimen. Each residual strain was calculated from lattice spacing change. Unstressed lattice spacing was determined experimentally using reference coupon specimens that were cut from the interior of same carburized cylinder. As a result, the diffraction peak width at half height, FWHM, near the carburized surface was about 3.7 times wider than that of coupon specimens. On the other hand, the most peak widths in the interior equaled to that of coupon specimens. Peak width broadened slightly as the diffracting volume approached the carburized case layer. From the center to the quarter of cylinder specimen, the hoop and axial strains were tensile, and the radial one was compressive in the interior. From the quarter to the edge of the cylinder specimen, the hoop tensile strain increased, radial and axial strains changed to tensile and compressive, respectively. Therefore, the interior of the cylinder specimen was found to be deformed elastically to balance the existence of compressive residual stresses in the carburized case layer. (author)

Rapid Quantitative Analysis of Naringenin in the Fruit Bodies of Inonotus vaninii by Two-phase Acid Hydrolysis Followed by Reversed Phase-high Performance Liquid Chromatography-ultra Violet.

Science.gov (United States)

Guohua, Xia; Pan, Ruirong; Bao, Rui; Ge, Yanru; Zhou, Cunshan; Shen, Yuping

2017-01-01

Sanghuang is one of mystical traditional Chinese medicines recorded earliest 2000 years ago, that included various fungi of Inonotus genus and was well-known for antitumor effect in modern medicine. Inonotus vaninii is grown in natural forest of Northeastern China merely and used as Sanghuang commercially, but it has no quality control specification until now. This study was to establish a rapid method of two-phase acid hydrolysis followed by reversed phase-high performance liquid chromatography-ultra violet (RP-HPLC-UV) to quantify naringenin in the fruit body of I. vaninii . Sample solution was prepared by pretreatment of raw material in two-phase acid hydrolysis and the hydrolysis technology was optimized. After reconstitution, analysis was performed using RP-HPLC-UV. The method validation was investigated and the naringenin content of sample and comparison were determined. The naringenin was obtained by two-phase acid hydrolysis method, namely, 10.0 g of raw material was hydrolyzed in 200 mL of 1% sulfuric acid aqueous solution (v/v) and 400 mL of chloroform in oil bath at 110°C for 2 h. Good linearity ( r = 0.9992) was achieved between concentration of analyte and peak area. The relative standard deviation (RSD) of precision was 2.47% and the RSD of naringenin contents for repeatability was 3.13%. The accuracy was supported with recoveries at 96.37%, 97.30%, and 99.31%. The sample solution prepared using the proposed method contained higher content of naringenin than conventional method and was stable for 8 h. Due to the high efficiency of sample preparation and high reliability of the HPLC method, it is feasible to use this method for routine analysis of naringenin in the fungus. A convenient two-phase acid hydrolysis was employed to produce naringenin from raw material, and then an efficient and reliable reversed phase-high performance liquid chromatography-ultra violet method was established to monitor naringenin in the fruit bodies of Inonotus vaninii

Photostability Characterization of Wood Polymer Composites of Polyvinyl Chloride and Rice Husk to Ultra-Violet Irradiation Exposure

Directory of Open Access Journals (Sweden)

Jais Farhana Hazwanee M.

2016-01-01

Full Text Available In this study, the photostability of wood polymer composites (WPC was assessed by using ultra-violet accelerated weathering test. Meanwhile, the mechanical properties of WPC show strength improvement at prolonged UV irradiation exposure with 43.21 MPa and maximum strain of 4.08 % at 5000 hours and 1000 hours UV irradiation exposure respectively. The colour stability of WPC was improved by addition of Ultraviolet (UV stabilizer during pre-mixing process which shows positive effect on the colour stability and prevented chalking of the composites for external use. Generally, discolourations of WPC during test exposure were caused by degradation of both wood and plastic. Therefore, incorporation with pigments and other additives gives improvement to the photostability of WPC. This is based on the increment of WPCs mechanical property while the morphological fracture surface of dumbbell test specimens revealed the pull out rice husk fiber which contributed to the distribution of load in the WPC samples.

Lung cancer mortality in nickel/chromium platers, 1946-95.

Science.gov (United States)

Sorahan, T; Burges, D C; Hamilton, L; Harrington, J M

1998-04-01

To investigate mortality from lung cancer in nickel/chromium platers. The mortality experience of a cohort of 1762 chrome workers (812 men, 950 women) from a large electroplating and light engineering plant in the Midlands, United Kingdom, was investigated for the period 1946-95. All subjects were first employed in chrome work at the plant during the period 1946-75, and had at least six months employment in jobs associated with exposure to chromic acid mist (hexavalent chromium). Detailed job histories were abstracted from original company personnel records and individual cumulative durations of employment in three types of chrome work were derived as time dependent variables (chrome bath work, other chrome work, any chrome work). Two analytical approaches were used--indirect standardisation and Poisson regression. Based on mortalities for the general population of England and Wales, male workers with some period of chrome bath work had higher lung cancer mortalities (observed deaths 40, expected deaths 25.41, standardised mortality ratio (SMR) 157, 95% confidence interval (95% CI) 113 to 214, p chrome workers (observed 9, expected 13.70, SMR 66, 95% CI 30 to 125). Similar findings were shown for female workers (chrome bath workers: observed 15, expected 8.57, SMR 175, 95% CI 98 to 289, p = 0.06; other chrome workers: observed 1, expected 4.37, SMR 23, 95% CI 1 to 127). Poisson regression was used to investigate risks of lung cancer relative to four categories of cumulative duration of chrome bath work and four categories of cumulative duration of other chrome work (none, or = 5 y). After adjusting for sex, age, calendar period, year of starting chrome work, period from first chrome work, and employment status (still employed v left employment), there was a significant positive trend (p chrome bath work and risks of mortality for lung cancer. Relative to a risk of unity for those chrome workers without any period of chrome bath work, risks were 2.83 (95% CI 1.47 to

Cell-cycle synchronisation of bloodstream forms of Trypanosoma brucei using Vybrant DyeCycle Violet-based sorting.

Science.gov (United States)

Kabani, Sarah; Waterfall, Martin; Matthews, Keith R

2010-01-01

Studies on the cell-cycle of Trypanosoma brucei have revealed several unusual characteristics that differ from the model eukaryotic organisms. However, the inability to isolate homogenous populations of parasites in distinct cell-cycle stages has limited the analysis of trypanosome cell division and complicated the understanding of mutant phenotypes with possible impact on cell-cycle related events. Although hydroxyurea-induced cell-cycle arrest in procyclic and bloodstream forms has been applied recently with success, such block-release protocols can complicate the analysis of cell-cycle regulated events and have the potential to disrupt important cell-cycle checkpoints. An alternative approach based on flow cytometry of parasites stained with Vybrant DyeCycle Orange circumvents this problem, but is restricted to procyclic form parasites. Here, we apply Vybrant Dyecycle Violet staining coupled with flow cytometry to effectively select different cell-cycle stages of bloodstream form trypanosomes. Moreover, the sorted parasites remain viable, although synchrony is rapidly lost. This method enables cell-cycle enrichment of populations of trypanosomes in their mammal infective stage, particularly at the G1 phase.

Adsorption and subsequent partial photodegradation of methyl violet 2B on Cu/Al layered double hydroxides

Energy Technology Data Exchange (ETDEWEB)

Guzmán-Vargas, Ariel, E-mail: aguzmanv@ipn.mx [Instituto Politécnico Nacional, ESIQIE-SEPI-DIQI, Laboratorio de Investigación en Materiales Porosos, Catálisis Ambiental y Química Fina (LiMpCa-QuF), UPALM Edif. 7 P.B. Zacatenco, GAM, México, D.F.07738 (Mexico); Lima, Enrique [Instituto de Investigaciones en Materiales-UNAM, Circuito exterior s/n, Cd. Universitaria, Del. Coyoacán, México, D.F. 04510 (Mexico); Uriostegui-Ortega, Gisselle A. [Instituto Politécnico Nacional, ESIQIE-SEPI-DIQI, Laboratorio de Investigación en Materiales Porosos, Catálisis Ambiental y Química Fina (LiMpCa-QuF), UPALM Edif. 7 P.B. Zacatenco, GAM, México, D.F.07738 (Mexico); Oliver-Tolentino, Miguel A. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Calzada Legaria 694, Col. Irrigación, México, D.F. 11500 (Mexico); Rodríguez, Esaú E. [Departamento de Química, Centro de Investigación y de Estudios Avanzados del Instituto Politécnico Nacional, Av. Instituto Politécnico Nacional 2580, Col. San Pedro Zacatenco, México, D.F. 07360 (Mexico)

2016-02-15

Graphical abstract: - Highlights: • LDH Cu/Al material showed high adsorption capacity. • Adsorption occurs by π–π interactions from the aromatic ring on the surface. • Adsorption mechanism fits to pseudo-second order model. • The photodegradation is due to the ·OH radical formation. - Abstract: Uncalcined Cu/Al LDH was studied as adsorbent and photocatalyst in the adsorption and subsequent photodegradation of methyl violet 2B dye (MV2B). Physicochemical characterization was carried out by XRD, FTIR, UV–vis, including photoactive properties, DSC/TGA and SEM. Kinetic and thermodynamic models showed great affinity and sorption capacity, the maximum adsorption capacity was 361.0 mg g{sup −1} obtained by Langmuir model, in addition, the results showed that the dye was adsorbed on the LDH surface. Photocatalytic activity was evaluated in the MV2B dye photodegradation process, and it was confirmed by the presence ·OH radicals monitored by EPR spin trapping technique, additionally, COD and TOC parameters were measured, {sup 13}C NMR showed differences for the adsorbed and photodegraded samples.

Adsorption and subsequent partial photodegradation of methyl violet 2B on Cu/Al layered double hydroxides

International Nuclear Information System (INIS)

Guzmán-Vargas, Ariel; Lima, Enrique; Uriostegui-Ortega, Gisselle A.; Oliver-Tolentino, Miguel A.; Rodríguez, Esaú E.

2016-01-01

Graphical abstract: - Highlights: • LDH Cu/Al material showed high adsorption capacity. • Adsorption occurs by π–π interactions from the aromatic ring on the surface. • Adsorption mechanism fits to pseudo-second order model. • The photodegradation is due to the ·OH radical formation. - Abstract: Uncalcined Cu/Al LDH was studied as adsorbent and photocatalyst in the adsorption and subsequent photodegradation of methyl violet 2B dye (MV2B). Physicochemical characterization was carried out by XRD, FTIR, UV–vis, including photoactive properties, DSC/TGA and SEM. Kinetic and thermodynamic models showed great affinity and sorption capacity, the maximum adsorption capacity was 361.0 mg g"−"1 obtained by Langmuir model, in addition, the results showed that the dye was adsorbed on the LDH surface. Photocatalytic activity was evaluated in the MV2B dye photodegradation process, and it was confirmed by the presence ·OH radicals monitored by EPR spin trapping technique, additionally, COD and TOC parameters were measured, "1"3C NMR showed differences for the adsorbed and photodegraded samples.

Vacuum ultra-violet damage and damage mitigation for plasma processing of highly porous organosilicate glass dielectrics

Energy Technology Data Exchange (ETDEWEB)

Marneffe, J.-F. de, E-mail: marneffe@imec.be; Lukaszewicz, M.; Porter, S. B.; Vajda, F.; Rutigliani, V.; Verdonck, P.; Baklanov, M. R. [IMEC v.z.w., 3001 Leuven (Belgium); Zhang, L.; Heyne, M.; El Otell, Z.; Krishtab, M. [IMEC v.z.w., 3001 Leuven (Belgium); Department of Chemistry, KULeuven, 3001 Leuven (Belgium); Goodyear, A.; Cooke, M. [Oxford Instruments Plasma Technology, BS49 4AP Bristol (United Kingdom)

2015-10-07

Porous organosilicate glass thin films, with k-value 2.0, were exposed to 147 nm vacuum ultra-violet (VUV) photons emitted in a Xenon capacitive coupled plasma discharge. Strong methyl bond depletion was observed, concomitant with a significant increase of the bulk dielectric constant. This indicates that, besides reactive radical diffusion, photons emitted during plasma processing do impede dielectric properties and therefore need to be tackled appropriately during patterning and integration. The detrimental effect of VUV irradiation can be partly suppressed by stuffing the low-k porous matrix with proper sacrificial polymers showing high VUV absorption together with good thermal and VUV stability. In addition, the choice of an appropriate hard-mask, showing high VUV absorption, can minimize VUV damage. Particular processing conditions allow to minimize the fluence of photons to the substrate and lead to negligible VUV damage. For patterned structures, in order to reduce VUV damage in the bulk and on feature sidewalls, the combination of both pore stuffing/material densification and absorbing hard-mask is recommended, and/or the use of low VUV-emitting plasma discharge.

Articulation of Native Cartilage Against Different Femoral Component Materials. Oxidized Zirconium Damages Cartilage Less Than Cobalt-Chrome.

Science.gov (United States)

Vanlommel, Jan; De Corte, Ronny; Luyckx, Jean Philippe; Anderson, Melissa; Labey, Luc; Bellemans, Johan

2017-01-01

Oxidized zirconium (OxZr) is produced by thermally driven oxidization creating an oxidized surface with the properties of a ceramic at the top of the Zr metal substrate. OxZr is much harder and has a lower coefficient of friction than cobalt-chrome (CoCr), both leading to better wear characteristics. We evaluated and compared damage to the cartilage of porcine patella plugs, articulating against OxZr vs CoCr. Our hypothesis was that, owing to its better wear properties, OxZr would damage cartilage less than CoCr. If this is true, OxZr might be a better material for the femoral component during total knee arthroplasty if the patella is not resurfaced. Twenty-one plugs from porcine patellae were prepared and tested in a reciprocating pin-on-disk machine while lubricated with bovine serum and under a constant load. Three different configurations were tested: cartilage-cartilage as the control group, cartilage-OxZr, and cartilage-CoCr. Macroscopic appearance, cartilage thickness, and the modified Mankin score were evaluated after 400,000 wear cycles. The control group showed statistically significant less damage than plugs articulating against both other materials. Cartilage plugs articulating against OxZr were statistically significantly less damaged than those articulating against CoCr. Although replacing cartilage by an implant always leads to deterioration of the cartilage counterface, OxZr results in less damage than CoCr. The use of OxZr might thus be preferable to CoCr in case of total knee arthroplasty without patella resurfacing. Copyright © 2016 Elsevier Inc. All rights reserved.

Health-friendly high-quality white light using violet-green-red laser and InGaN nanowires-based true yellow nanowires light-emitting diodes

KAUST Repository

Janjua, Bilal

2017-02-16

White light based on blue laser - YAG: Ce phosphor has the advantage of implementing solid-state lighting and optical wireless communications combined-functionalities in a single lamp. However, the blue light was found to disrupt melatonin production, and therefore the human circadian rhythm in general; while the yellow phosphor is susceptible to degradation by laser irradiation and also lack tunability in color rendering index (CRI). In this investigation, by using a violet laser, which has 50% less impact on circadian response, as compared to blue light, and an InGaN-quantum-disks nanowires-based light-emitting diode (NWs-LED), we address both issues simultaneously. The white light is therefore generated using violet-green-red lasers, in conjunction with a yellow NWs-LED realized using molecular beam epitaxy technique, on titanium-coated silicon substrates. Unlike the conventional quantum-well-based LED, the NWs-LED showed efficiency-droop free behavior up to 9.8 A/cm with peak output power of 400 μW. A low turn-on voltage of ∼2.1 V was attributed to the formation of conducting titanium nitride layer at NWs nucleation site and improved fabrication process in the presence of relatively uniform height distribution. The 3D quantum confinement and the reduced band bending improve carriers-wavefunctions overlap, resulting in an IQE of ∼39 %. By changing the relative intensities of the individual color components, CRI of >85 was achieved with tunable correlated color temperature (CCT), thus covering the desired room lighting conditions. Our architecture provides important considerations in designing smart solid-state lighting while addressing the harmful effect of blue light.

Health-friendly high-quality white light using violet-green-red laser and InGaN nanowires-based true yellow nanowires light-emitting diodes

Science.gov (United States)

Janjua, Bilal; Ng, Tien K.; Zhao, Chao; Anjum, Dalaver H.; Prabaswara, Aditya; Consiglio, Giuseppe Bernardo; Shen, Chao; Ooi, Boon S.

2017-02-01

White light based on blue laser - YAG: Ce3+ phosphor has the advantage of implementing solid-state lighting and optical wireless communications combined-functionalities in a single lamp. However, the blue light was found to disrupt melatonin production, and therefore the human circadian rhythm in general; while the yellow phosphor is susceptible to degradation by laser irradiation and also lack tunability in color rendering index (CRI). In this investigation, by using a violet laser, which has 50% less impact on circadian response, as compared to blue light, and an InGaN-quantum-disks nanowires-based light-emitting diode (NWs-LED), we address both issues simultaneously. The white light is therefore generated using violet-green-red lasers, in conjunction with a yellow NWs-LED realized using molecular beam epitaxy technique, on titanium-coated silicon substrates. Unlike the conventional quantum-well-based LED, the NWs-LED showed efficiency-droop free behavior up to 9.8 A/cm2 with peak output power of 400 μW. A low turn-on voltage of 2.1 V was attributed to the formation of conducting titanium nitride layer at NWs nucleation site and improved fabrication process in the presence of relatively uniform height distribution. The 3D quantum confinement and the reduced band bending improve carriers-wavefunctions overlap, resulting in an IQE of 39 %. By changing the relative intensities of the individual color components, CRI of >85 was achieved with tunable correlated color temperature (CCT), thus covering the desired room lighting conditions. Our architecture provides important considerations in designing smart solid-state lighting while addressing the harmful effect of blue light.

Label-free characterization of ultra violet-radiation-induced changes in skin fibroblasts with Raman spectroscopy and quantitative phase microscopy.

Science.gov (United States)

Singh, S P; Kang, Sungsam; Kang, Jeon Woong; So, Peter T C; Dasari, Ramanchandra Rao; Yaqoob, Zahid; Barman, Ishan

2017-09-07

Minimizing morbidities and mortalities associated with skin cancers requires sustained research with the goal of obtaining fresh insights into disease onset and progression under specific stimuli, particularly the influence of ultraviolet rays. In the present study, label-free profiling of skin fibroblasts exposed to time-bound ultra-violet radiation has been performed using quantitative phase imaging and Raman spectroscopy. Statistically significant differences in quantifiable biophysical parameters, such as matter density and cell dry mass, were observed with phase imaging. Accurate estimation of changes in the biochemical constituents, notably nucleic acids and proteins, was demonstrated through a combination of Raman spectroscopy and multivariate analysis of spectral patterns. Overall, the findings of this study demonstrate the promise of these non-perturbative optical modalities in accurately identifying cellular phenotypes and responses to external stimuli by combining molecular and biophysical information.

Effects of as-cast and wrought Cobalt-Chrome-Molybdenum and Titanium-Aluminium-Vanadium alloys on cytokine gene expression and protein secretion in J774A.1 macrophages

DEFF Research Database (Denmark)

Jakobsen, Stig Storgaard; Larsen, Agnete; Stoltenberg, Meredin

2007-01-01

the cell viability. Surface properties of the discs were characterised with a profilometer and with energy dispersive X-ray spectroscopy. We here report, for the first time, that the prosthetic material surface (non-phagocytable) of as-cast high carbon CoCrMo reduces the pro-inflammatory cytokine IL-6......Insertion of metal implants is associated with a possible change in the delicate balance between pro- and anti-inflammatory proteins, probably leading to an unfavourable predominantly pro-inflammatory milieu. The most likely cause is an inappropriate activation of macrophages in close relation...... to the metal implant and wear-products. The aim of the present study was to compare surfaces of as-cast and wrought Cobalt-Chrome-Molybdenum (CoCrMo) alloys and Titanium-Aluminium-Vanadium (TiAlV) alloy when incubated with mouse macrophage J774A.1 cell cultures. Changes in pro- and anti-inflammatory cytokines...

Functional characterization of spectral tuning mechanisms in the great bowerbird short-wavelength sensitive visual pigment (SWS1), and the origins of UV/violet vision in passerines and parrots.

Science.gov (United States)

van Hazel, Ilke; Sabouhanian, Amir; Day, Lainy; Endler, John A; Chang, Belinda S W

2013-11-13

One of the most striking features of avian vision is the variation in spectral sensitivity of the short wavelength sensitive (SWS1) opsins, which can be divided into two sub-types: violet- and UV- sensitive (VS & UVS). In birds, UVS has been found in both passerines and parrots, groups that were recently shown to be sister orders. While all parrots are thought to be UVS, recent evidence suggests some passerine lineages may also be VS. The great bowerbird (Chlamydera nuchalis) is a passerine notable for its courtship behaviours in which males build and decorate elaborate bower structures. The great bowerbird SWS1 sequence possesses an unusual residue combination at known spectral tuning sites that has not been previously investigated in mutagenesis experiments. In this study, the SWS1 opsin of C. nuchalis was expressed along with a series of spectral tuning mutants and ancestral passerine SWS1 pigments, allowing us to investigate spectral tuning mechanisms and explore the evolution of UV/violet sensitivity in early passerines and parrots. The expressed C. nuchalis SWS1 opsin was found to be a VS pigment, with a λmax of 403 nm. Bowerbird SWS1 mutants C86F, S90C, and C86S/S90C all shifted λmax into the UV, whereas C86S had no effect. Experimentally recreated ancestral passerine and parrot/passerine SWS1 pigments were both found to be VS, indicating that UV sensitivity evolved independently in passerines and parrots from a VS ancestor. Our mutagenesis studies indicate that spectral tuning in C. nuchalis is mediated by mechanisms similar to those of other birds. Interestingly, our ancestral sequence reconstructions of SWS1 in landbird evolution suggest multiple transitions from VS to UVS, but no instances of the reverse. Our results not only provide a more precise prediction of where these spectral sensitivity shifts occurred, but also confirm the hypothesis that birds are an unusual exception among vertebrates where some descendants re-evolved UVS from a violet type

Capillary electrophoresis of chitooligosaccharides in acidic solution: simple determination using a quaternary-ammonium-modified column and indirect photometric detection with crystal violet.

Science.gov (United States)

Hattori, Toshiaki; Anraku, Nobuhiro; Kato, Ryo

2010-02-01

Five chitosan oligosaccharides were separated in acidic aqueous solution by capillary electrophoresis (CE) with indirect photometric detection using a positively coated capillary. Electrophoretic mobility of the chitooligosaccharides (COSs) depended on the number of monomer units in acidic aqueous solution, similar to other polyelectrolyte oligomers. The separation was developed in nitric acid aqueous solution at pH 3.0 with 1 mM Crystal Violet, using a capillary positively coated with N-trimethoxypropyl-N,N,N-trimethylammonium chloride. The limit of the detection for chitooligosaccharides with two to six saccharide chains was less than 5 microM. CE determination of an enzymatically hydrolyzed COS agreed with results from HPLC. 2009 Elsevier B.V. All rights reserved.

Pemanfaatan kembali krom limbah shaving untuk penyamakan kulit

Directory of Open Access Journals (Sweden)

Sri Sutyasmi

2014-12-01

Full Text Available This study aims to determine the extent of chrome in shaving waste that can be recovered and reused for tanning the leather and to reduce environmental pollution. Three kg of chrome shaving waste was hydrolyzed with NaOH by variation of 1, 2 and 3 % respectively in 10 liters of water, at temperature of 100oC for 1 hour. The results solution was then filtered to separate the chrome from the collagen protein . The filtered solids chrome was recovery by concentrated using sulfuric acid. The resulting chrome has Cr2O3 about 11 g/kg of chromium with utiluzation of 2 % NaOH. The recovered chrome was used for tanning goat skin with variation of 0, 30, 40, 50, 60, 70, and 100% respectively from total chrome used for tanning leather. Test result showed that the variation of 60 % met the standard of SNI 0253-2009: Upper leather footwear-goat. The use of recovered chrome reduce environmental pollution.

Estimation of environmental mobility of heavy metals using a sequential leaching of particulate material emitted from an opencast chrome mine complex

Energy Technology Data Exchange (ETDEWEB)

Poeykioe, R. [Meri-Lappi Institute, Centre for Environmental Technology, University of Oulu, Kemi (Finland); Peraemaeki, P.; Kuokkanen, T. [University of Oulu, Department of Chemistry, Oulu (Finland); Vaelimaeki, I. [Suomen Ympaeristoepalvelu Oy, Oulu (Finland)

2002-06-01

A four-stage sequential leaching procedure was applied to assess the bioavailability and environmental mobility of heavy metals (Cr, Fe, Cu, Ni and Cd) in total suspended particulate (TSP) material emitted from an opencast chrome mine complex (Kemi, Northern Finland). TSP material was collected on glass fibre filters by a high-volume sampler, and a sequential leaching procedure was used to determine the distribution of heavy metals between the water-soluble fraction (H{sub 2}O), environmentally mobile fraction (CH{sub 3}COONH{sub 4}), the fraction bound to carbonate and oxides (HONH{sub 3}Cl + CH{sub 3}COOH), and the fraction bound to silicates and organic matter, that is the environmentally immobile fraction (HNO{sub 3} + HF + HCl). The sequential leaching procedure was also applied to the certified reference materials VKI (QC Loam Soil A) and PACS-2 (Marine Sediment) to evaluate the accuracy and reproducibility of the leaching procedure. The heavy metals were determined by graphite furnace atomic absorption spectrometry (GFAAS) and flame atomic absorption spectrometry (FAAS). The concentrations of metals in the water-soluble fraction (H{sub 2}O) decreased in the order Fe >Cu >Cr >Ni >Cd, and in the environmentally mobile fraction (CH{sub 3}COONH{sub 4}) in the order Cu >Fe >Ni >Cr >Cd. (orig.)

非クロム羊革を使用したドレス手袋の機能特性

OpenAIRE

角田, 由美子; 岡村, 浩; Yumiko, Tsunoda; Hiroshi, Okamura; 昭和女子大学大学院生活科学研究専攻; 昭和女子大学大学院

2006-01-01

Three types of non-chrome-tanned sheep skin leather processed with different fatliquoring agents and one type of chrome-tanned sheep skin leather as a control were used to make dress gloves for comparison of their functional properties. The results indicated only a slight difference between the non-chrome and chrome-tanned leathers in moisture characteristic, warmth keeping property, temperature within the gloves. The tear strength of the non-chrome leather, however was remarkably lower than ...

Penanganan Limbah Krom Dengan Metode Destruksi Kimia

OpenAIRE

Wiryodiningrat, Suliestiyah; Kismolo, Endro; Prayitno, Prayitno

2007-01-01

The treatment of chrome waste water was conducted by chemical destruction method. Chromium recovery process that at the same time lowering the chrome content is considered the best solution so far. The treatment of chrome The treatment of chrome waste water was done by chemical process using Magnesium Oxide and Lime to produce Sludge of Chromium performed. By the process of chemical destruction method using Sulphuric Acid, Chrome Sulphate or Chromosal powder that can be used as an alternative...

Penanganan limbah krom dengan metode destruksi kimia

OpenAIRE

Suliestiyah Wiryodiningrat; Endro Kismolo; Prayitno Prayitno

2007-01-01

The treatment of chrome waste water was conducted by chemical destruction method. Chromium recovery process that at the same time lowering the chrome content is considered the best solution so far. The treatment of chrome The treatment of chrome waste water was done by chemical process using Magnesium Oxide and Lime to produce Sludge of Chromium performed. By the process of chemical destruction method using Sulphuric Acid, Chrome Sulphate or Chromosal powder that can be used as an alternative...

The effects of welding parameters on ultra-violet light emissions, ozone and CrVI formation in MIG welding.

Science.gov (United States)

Dennis, J H; Mortazavi, S B; French, M J; Hewitt, P J; Redding, C R

1997-01-01

This paper describes the relationships between ultra-violet emission, ozone generation and CrVI production in MIG welding which were measured as a function of shield gas flow rate, welding voltage, electrode stick-out and shield gas composition using an automatic welding rig that permitted MIG welding under reproducible conditions. The experimental results are interpreted in terms of the physico-chemical processes occurring in the micro- and macro-environments of the arc as part of research into process modification to reduce occupational exposure to ozone and CrVI production rates in MIG welding. We believe the techniques described here, and in particular the use of what we have termed u.v.-ozone measurements, will prove useful in further study of ozone generation and CrVI formation and may be applied in the investigation of engineering control of occupational exposure in MIG and other welding process such as Manual Metal Arc (MMA) and Tungsten Inert Gas (TIG).

Ultra-violet absorption induced modifications in bulk and nanoscale electrical transport properties of Al-doped ZnO thin films

Energy Technology Data Exchange (ETDEWEB)

Kumar, Mohit; Basu, Tanmoy; Som, Tapobrata, E-mail: tsom@iopb.res.in [SUNAG Laboratory, Institute of Physics, Sachivalaya Marg, Bhubaneswar 751 005 (India)

2015-08-07

Using conductive atomic force microscopy and Kelvin probe force microscopy, we study local electrical transport properties in aluminum-doped zinc oxide (ZnO:Al or AZO) thin films. Current mapping shows a spatial variation in conductivity which corroborates well with the local mapping of donor concentration (∼10{sup 20 }cm{sup −3}). In addition, a strong enhancement in the local current at grains is observed after exposing the film to ultra-violet (UV) light which is attributed to persistent photocurrent. Further, it is shown that UV absorption gives a smooth conduction in AZO film which in turn gives rise to an improvement in the bulk photoresponsivity of an n-AZO/p-Si heterojunction diode. This finding is in contrast to the belief that UV absorption in an AZO layer leads to an optical loss for the underneath absorbing layer of a heterojunction solar cell.

The Performance of Chrome-Coated Copper as Metallic Catalytic Converter to Reduce Exhaust Gas Emissions from Spark-Ignition Engine

Science.gov (United States)

Warju; Harto, S. P.; Soenarto

2018-01-01

One of the automotive technologies to reduce exhaust gas emissions from the spark-ignition engine (SIE) is by using a catalytic converter. The aims of this research are firstly to conduct a metallic catalytic converter, secondly to find out to what extend chrome-coated copper plate (Cu+Cr) as a catalyst is efficient. To measure the concentration of carbon monoxide (CO) and hydrocarbon (HC) on the frame there are two conditions required. First is when the standard condition, and second is when Cu+Cr metallic catalytic converter is applied using exhaust gas analyzer. Exhaust gas emissions from SIE are measured by using SNI 19-7118.1-2005. The testing of CO and HC emissions were conducted with variable speed to find the trend of exhaust gas emissions from idle speed to high speed. This experiment results in the fact that the use of Cu+Cr metallic catalytic converter can reduce the production of CO and HC of a four-stroke gasoline engine. The reduction of CO and HC emission are 95,35% and 79,28%. Using active metal catalyst in form of metallic catalytic converter, it is gained an optimum effective surface of a catalyst which finally is able to decrease the amount of CO and HC emission significantly in every spinning happened in the engine. Finally, this technology can be applied to the spark ignition engine both car and motorcycle to support blue sky program in Indonesia.

Effects of as-cast and wrought Cobalt-Chrome-Molybdenum and Titanium-Aluminium-Vanadium alloys on cytokine gene expression and protein secretion in J774A.1 macrophages

DEFF Research Database (Denmark)

Jakobsen, Stig Storgaard; Larsen, Agnete; Stoltenberg, Meredin

2007-01-01

to the metal implant and wear-products. The aim of the present study was to compare surfaces of as-cast and wrought Cobalt-Chrome-Molybdenum (CoCrMo) alloys and Titanium-Aluminium-Vanadium (TiAlV) alloy when incubated with mouse macrophage J774A.1 cell cultures. Changes in pro- and anti-inflammatory cytokines...... transcription, the chemokine MCP-1 secretion, and M-CSF secretion by 77%, 36%, and 62%, respectively. Furthermore, we found that reducing surface roughness did not affect this reduction. The results suggest that as-cast CoCrMo alloy is more inert than wrought CoCrMo and wrought TiAlV alloys and could prove...... the cell viability. Surface properties of the discs were characterised with a profilometer and with energy dispersive X-ray spectroscopy. We here report, for the first time, that the prosthetic material surface (non-phagocytable) of as-cast high carbon CoCrMo reduces the pro-inflammatory cytokine IL-6...

Penanganan limbah krom dengan metode destruksi kimia

Directory of Open Access Journals (Sweden)

Suliestiyah Wiryodiningrat

2007-06-01

Full Text Available The treatment of chrome waste water was conducted by chemical destruction method. Chromium recovery process that at the same time lowering the chrome content is considered the best solution so far. The treatment of chrome The treatment of chrome waste water was done by chemical process using Magnesium Oxide and Lime to produce Sludge of Chromium performed. By the process of chemical destruction method using Sulphuric Acid, Chrome Sulphate or Chromosal powder that can be used as an alternative tanning agent can be obtained. It can be concluded from the research that destruction process of Chrome Hydroxide Sludge of Lime Process requires speed of stirring 100 rpm. At this state, the content of soluble Solid Substance in Chromium Sulphate Liquor was 5.125 g/l, and the solubility of chromosal in water was 99.15%, whereas for Sludge of Chrome Hydoxide from Magnesium Oxide process, the best speed of stirring was 150 rpm, with soluble solid substance in the Chrome Sulphate was 4.085 g/l and solubility of Chromosal powder in water was 99.54%.

Room-Temperature Continuous-Wave Operation of InGaN-Based Blue-Violet Laser Diodes with a Lifetime of 15.6 Hours

International Nuclear Information System (INIS)

Zeng Chang; Zhang Shu-Ming; Ji Lian; Zhao De-Gang; Zhu Jian-Jun; Liu Zong-Shun; Jiang De-Sheng; Duan Li-Hong; Wang Hai; Shi Yong-Sheng; Liu Su-Ying; Yang Hui; Wang Huai-Bing; Cao Qing; Chong Ming; Chen Liang-Hui

2010-01-01

We report our recent progress of investigations on InGaN-based blue-violet laser diodes (LDs). The room-temperature (RT) cw operation lifetime of LDs has extended to longer than 15.6 h. The LD structure was grown on a c-plane free-standing (FS) GaN substrate by metal organic chemical vapor deposition (MOCVD). The typical threshold current and voltage of LD under RT cw operation are 78 mA and 6.8 V, respectively. The experimental analysis of degradation of LD performances suggests that after aging treatment, the increase of series resistance and threshold current can be mainly attributed to the deterioration of p-type ohmic contact and the decrease of internal quantum efficiency of multiple quantum well (MQW), respectively. (fundamental areas of phenomenology(including applications))

The relation between radio flux density and ionizing ultra-violet flux for HII regions and supernova remnants in the Large Magellanic cloud

Directory of Open Access Journals (Sweden)

Filipović M.D.

2003-01-01

Full Text Available We present a comparison between the Parkes radio surveys (Filipović et al 1995 and Vacuum Ultra-Violet (VUV surveys (Smith et al. 1987 of the Large Magellanic Clouds (LMC. We have found 72 sources in common in the LMC which are known HII regions (52 and supernova remnants (SNRs (19. Some of these radio sources are associated with two or more UV stellar associations. A comparison of the radio flux densities and ionizing UV flux for HII regions shows a very good correlation, as expected from theory. Many of the Magellanic Clouds (MCs SNRs are embedded in HII regions, so there is also a relation between radio and UV which we attribute to the surrounding HII regions.

Hexavalent Chromium Free Coatings Projects for Aerospace Applications

Science.gov (United States)

2012-08-01

laboratory qualification of a total hexavalent chrome free coating systems for use on magnesium transmission housings. This project will leverage... hexavalent chrome free coating system by utilizing a hexavalent chrome free topcoat, primer, and pretreatment for magnesium parts used on Army...of the hexavalent chrome free conversion coatings. Hexavalent Chromium Free Coating System for Magnesium Housings on Aviation Systems Desert

Determination of the total blood volume of the rat using chromium 51 (1962); Determination du volume sanguin total chez le rat a l'aide du chrome 51 (1962)

Energy Technology Data Exchange (ETDEWEB)

Bernard, Y; Rinaldi, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1962-07-01

In various experiments it is important that the rat's blood volume should be known and it is essential that it could be worked out by simply weighing the animal. Therefore authors decided to work out systematically with chromium 51 blood volume for rats with different weights. Results have shown that blood volume for 100 g is 5.55 ml and that it does not seen to vary with the weight of animals. (authors) [French] La connaissance de la masse sanguine chez le rat est indispensable dans de nombreuses experiences et il est essentiel de pouvoir l'evaluer apres une simple pesee de l'animal. C'est dans ce but que les auteurs ont entrepris la determination systematique de la masse sanguine a l'aide du chrome 51 chez des rats de poids differents. Les resultats obtenus ont montre que la masse sanguine rapportee a 100 grammes d'animal est de 5,53 millilitres, et qu'elle ne parait pas varier avec le poids de l'animal. (auteurs)

Evaluation of marginal/internal fit of chrome-cobalt crowns: Direct laser metal sintering versus computer-aided design and computer-aided manufacturing.

Science.gov (United States)

Gunsoy, S; Ulusoy, M

2016-01-01

The purpose of this study was to evaluate the internal and marginal fit of chrome cobalt (Co-Cr) crowns were fabricated with laser sintering, computer-aided design (CAD) and computer-aided manufacturing, and conventional methods. Polyamide master and working models were designed and fabricated. The models were initially designed with a software application for three-dimensional (3D) CAD (Maya, Autodesk Inc.). All models were fabricated models were produced by a 3D printer (EOSINT P380 SLS, EOS). 128 1-unit Co-Cr fixed dental prostheses were fabricated with four different techniques: Conventional lost wax method, milled wax with lost-wax method (MWLW), direct laser metal sintering (DLMS), and milled Co-Cr (MCo-Cr). The cement film thickness of the marginal and internal gaps was measured by an observer using a stereomicroscope after taking digital photos in ×24. Best fit rates according to mean and standard deviations of all measurements was in DLMS both in premolar (65.84) and molar (58.38) models in μm. A significant difference was found DLMS and the rest of fabrication techniques (P 0.05). DMLS was best fitting fabrication techniques for single crown based on the results.The best fit was found in marginal; the larger gap was found in occlusal.All groups were within the clinically acceptable misfit range.

A study on the utilization of chromic oxide wastes

Energy Technology Data Exchange (ETDEWEB)

Hong, Seung Woong; Kim, Chi Kwon; Hwang, Seon Kook; Kim, Byung Gyu; Son, Jeong Soo; Nam, Chul Woo [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

This study was carried out to develop the optimum process for recovering precious and valuable metals from chrome oxide wastes. The following subjects such as, (1) feasibility on the recovery of precious and valuable metals, (2) recovery rate of precious and valuable metals, (3) purification of extracted precious and valuable metals, and (4) environmental aspects of recovery process, were investigated and the main results are as follows. (1) With Sem analysis of chrome oxide wastes, it was found that combustion process for eliminating oil and water in wastes, was necessary. (2) After leaching chrome oxide wastes with nitric acid and aqua regia, silver and gold were effectively separated and recovered. But a lot of silver and gold were remaining in the leaching residue. It was considered that chrome oxide powder was coated with organic materials during polishing stage and their products were insoluble in acidic solution. (3) The optimum process for separation and recovery of precious metal and production of new chrome oxide is consist of several process such as perchloric acid leaching, recovery of silver chloride, cementation for gold, reduction of chrome ion, and production of pure chrome oxide. (4) For separating chrome compound from the chrome oxide waste occurred in stainless steel polishing process, alkali roasting process was suggested. (author). 18 refs., 29 figs., 11 tabs.

From Serendipity to Rational Design: Tuning the Blue Trigonal Bipyramidal Mn3+ Chromophore to Violet and Purple through Application of Chemical Pressure.

Science.gov (United States)

Li, Jun; Lorger, Simon; Stalick, Judith K; Sleight, Arthur W; Subramanian, M A

2016-10-03

We recently reported that an allowed d-d transition of trigonal bipyramidal (TBP) Mn 3+ is responsible for the bright blue color in the YIn 1-x Mn x O 3 solid solution. The crystal field splitting between a'(d z 2 ) and e'(d x 2 -y 2 , d xy ) energy levels is very sensitive to the apical Mn-O distance. We therefore applied chemical pressure to compress the apical Mn-O distance in YIn 1-x Mn x O 3 , move the allowed d-d transition to higher energy, and thereby tune the color from blue to violet/purple. This was accomplished by substituting smaller cations such as Ti 4+ /Zn 2+ and Al 3+ onto the TBP In/Mn site, which yielded novel violet/purple phases. The general formula is YIn 1-x-2y-z Mn x Ti y Zn y Al z O 3 (x = 0.005-0.2, y = 0.1-0.4, and z ≤ 0.1), where the color darkens with the increasing amount of Mn. Higher y or small additions of Al provide a more reddish hue to the resulting purple colors. Substituting other rare earth cations for Y has little impact on color. Crystal structure analysis by neutron powder diffraction confirms a shorter apical Mn-O distance compared with that in the blue YIn 1-x Mn x O 3 . Magnetic susceptibility measurements verify the 3+ oxidation state for Mn. Diffuse reflection spectra were obtained over the wavelength region 200-2500 nm. All samples show excellent near-infrared reflectance comparable to that of commercial TiO 2 , making them ideal for cool pigment applications such as energy efficient roofs of buildings and cars where reducing solar heat to save energy is desired. In a comparison with commercial purple pigments, such as Co 3 (PO 4 ) 2 , our pigments are much more thermally stable and chemically inert, and are neither toxic nor carcinogenic.

Environmental Projects for Aerospace Applications

Science.gov (United States)

2012-05-23

successful, the end product would be laboratory qualification of a total hexavalent chrome free coating systems for use on magnesium transmission...qualification testing of a completely hexavalent chrome free coating system by utilizing a hexavalent chrome free topcoat, primer, and pretreatment...Evaluate the use of hexavalent chrome free conversion coatings for depot and field applications.  Alodine 5700 and Alodine T 5900 immersion for

Adsorption equilibrium and kinetic studies of crystal violet and naphthol green on torreya-grandis-skin-based activated carbon

International Nuclear Information System (INIS)

Dai, Wei; Yu, Huijing; Ma, Na; Yan, Xiaoyang

2015-01-01

A new type of activated carbon, torreya-grandis-skin-based activated carbon (TAC), has been used to remove the harmful dyes (cationic dye crystal violet (CV) and anionic dye naphthol green (NG)) from contaminated water via batch adsorption. The effects of solution pH, adsorption time and temperature were studied. The Langmuir and Freundlich adsorption models were used to describe the equilibrium isotherm and isotherm constant calculation. It was found that the maximum equilibrium adsorption capacities were 292mg/g and 545mg/g for CV and NG, respectively. Adsorption kinetics was verified by pseudo-first-order, pseudo-second-order and intra-particle diffusion kinetic models. Results indicated that the rate of dye adsorption followed pseudo-second-order kinetic model for the initial dye concentration range studied. Temperature-dependent adsorption behavior of CV and NG shows that the adsorption is spontaneous and endothermic, accompanying an entropy increase. This work indicates that TAC could be employed as a low-cost alternative for the removal of the textile dyes from effluents

Reaction of photochemical resists used in screen printing under the influence of digitally modulated ultra violet light

Science.gov (United States)

Gmuender, T.

2017-02-01

Different chemical photo-reactive emulsions are used in screen printing for stencil production. Depending on the bandwidth, optical power and depth of field from the optical system, the reaction / exposure speed has a diverse value. In this paper, the emulsions get categorized and validated in a first step. After that a mathematical model gets developed and adapted due to heuristic experience to estimate the exposure speed under the influence of digitally modulated ultra violet (UV) light. The main intention is to use the technical specifications (intended wavelength, exposure time, distance to the stencil, electrical power, stencil configuration) in the emulsion data sheet primary written down with an uncertainty factor for the end user operating with large projector arc lamps and photo films. These five parameters are the inputs for a mathematical formula which gives as an output the exposure speed for the Computer to Screen (CTS) machine calculated for each emulsion / stencil setup. The importance of this work relies in the possibility to rate with just a few boundaries the performance and capacity of an exposure system used in screen printing instead of processing a long test series for each emulsion / stencil configuration.

Effect of organic media on growth and development of patiola F1 horned violet (Viola cornuta L.

Directory of Open Access Journals (Sweden)

Dorota Janicka

2013-04-01

Full Text Available The specificity of horticultural production makes it possible to use substrates based on compost from municipal and industrial waste, particularly in the cultivation of ornamental plants. Experiments were conducted in the years 2005–2007. Six horned violet cultivars (Viola cornuta  L. from Patiola F1 group and four substrates were used in them: I – sphagnum peat; II – substrate from peat and compost 1 (1:1 v/v; III – substrate from peat and compost 2 (1:1 v/v; IV – coconut fibre. Compost 1 was prepared using municipal sewage sludge (35%, potato pulp (35% and straw (30%. Compost 2 was prepared using municipal sewage sludge (35%, potato pulp (35% and sawdust (30%. Composts after 10 months of composting were used in the research. The addition of municipal sewage sludge composts did not cause observable adverse changes in plants grown. Composts made from municipal sewage sludge are rich in nutrients. Plants that are grown in substrates with the addition of composts and in a peat substrate grow and develop properly without the necessity of introducing top dressing.

Localization microscopy of DNA in situ using Vybrant{sup ®} DyeCycle™ Violet fluorescent probe: A new approach to study nuclear nanostructure at single molecule resolution

Energy Technology Data Exchange (ETDEWEB)

Żurek-Biesiada, Dominika [Laboratory of Cell Biophysics, Faculty of Biochemistry, Biophysics and Biotechnology, Jagiellonian University, Gronostajowa 7, 30-387 Kraków (Poland); Szczurek, Aleksander T. [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Prakash, Kirti [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Institute for Pharmacy and Molecular Biotechnology (IPMB), University of Heidelberg, Im Neuenheimer Feld 364, D-69120 Heidelberg (Germany); Mohana, Giriram K. [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Lee, Hyun-Keun [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Department of Physics, University of Mainz (JGU), Staudingerweg 7, 55128 Mainz (Germany); Roignant, Jean-Yves [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Birk, Udo J. [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Department of Physics, University of Mainz (JGU), Staudingerweg 7, 55128 Mainz (Germany); Dobrucki, Jurek W., E-mail: jerzy.dobrucki@uj.edu.pl [Laboratory of Cell Biophysics, Faculty of Biochemistry, Biophysics and Biotechnology, Jagiellonian University, Gronostajowa 7, 30-387 Kraków (Poland); Cremer, Christoph, E-mail: c.cremer@imb-mainz.de [Institute of Molecular Biology (IMB), Ackermannweg 4, 55128 Mainz (Germany); Institute for Pharmacy and Molecular Biotechnology (IPMB), University of Heidelberg, Im Neuenheimer Feld 364, D-69120 Heidelberg (Germany); Department of Physics, University of Mainz (JGU), Staudingerweg 7, 55128 Mainz (Germany)

2016-05-01

Higher order chromatin structure is not only required to compact and spatially arrange long chromatids within a nucleus, but have also important functional roles, including control of gene expression and DNA processing. However, studies of chromatin nanostructures cannot be performed using conventional widefield and confocal microscopy because of the limited optical resolution. Various methods of superresolution microscopy have been described to overcome this difficulty, like structured illumination and single molecule localization microscopy. We report here that the standard DNA dye Vybrant{sup ®} DyeCycle™ Violet can be used to provide single molecule localization microscopy (SMLM) images of DNA in nuclei of fixed mammalian cells. This SMLM method enabled optical isolation and localization of large numbers of DNA-bound molecules, usually in excess of 10{sup 6} signals in one cell nucleus. The technique yielded high-quality images of nuclear DNA density, revealing subdiffraction chromatin structures of the size in the order of 100 nm; the interchromatin compartment was visualized at unprecedented optical resolution. The approach offers several advantages over previously described high resolution DNA imaging methods, including high specificity, an ability to record images using a single wavelength excitation, and a higher density of single molecule signals than reported in previous SMLM studies. The method is compatible with DNA/multicolor SMLM imaging which employs simple staining methods suited also for conventional optical microscopy. - Highlights: • Super-resolution imaging of nuclear DNA with Vybrant Violet and blue excitation. • 90nm resolution images of DNA structures in optically thick eukaryotic nuclei. • Enhanced resolution confirms the existence of DNA-free regions inside the nucleus. • Optimized imaging conditions enable multicolor super-resolution imaging.

Determination of polyhexamethylene biguanide hydrochloride using photometric colloidal titration with crystal violet as a color indicator.

Science.gov (United States)

Masadome, Takashi; Miyanishi, Takaaki; Watanabe, Keita; Ueda, Hiroshi; Hattori, Toshiaki

2011-01-01

A solution of polyhexamethylene biguanide hydrochloride (PHMB-HCl) was titrated with a standard solution of potassium poly(vinyl sulfate) (PVSK) using crystal violet (CV) as an photometric indicator cation. The end point was detected by a sharp absorbance change due to an abrupt decrease in the concentration of CV. A linear relationship between the concentration of PHMB-HCl and the end-point volume of the titrant existed in the concentration range from 2 to 10 × 10(-6) eq mol L(-1). Back-titration was based on adding an excess amount of PVSK to a sample solution containing CV, which was titrated with a standard solution of poly(diallyldimethylammonium chloride) (PDADMAC). The calibration curve of the PHMB-HCl concentration to the end point volume of the titrant was also linear in the concentration range from 2 to 8 × 10(-6) eq mol L(-1). Both photometric titrations were applied to the determination of PHMB-HCl in a few contact-lens detergents. Back-titration showed a clear end point, but direct titration showed an unclear end point. The results of the back-titration of PHMB-HCl were compared with the content registered in its labels. 2011 © The Japan Society for Analytical Chemistry

Epigenetic differentiation and relationship to adaptive genetic divergence in discrete populations of the violet Viola cazorlensis.

Science.gov (United States)

Herrera, Carlos M; Bazaga, Pilar

2010-08-01

*In plants, epigenetic variations based on DNA methylation are often heritable and could influence the course of evolution. Before this hypothesis can be assessed, fundamental questions about epigenetic variation remain to be addressed in a real-world context, including its magnitude, structuring within and among natural populations, and autonomy in relation to the genetic context. *Extent and patterns of cytosine methylation, and the relationship to adaptive genetic divergence between populations, were investigated for wild populations of the southern Spanish violet Viola cazorlensis (Violaceae) using the methylation-sensitive amplified polymorphism (MSAP) technique, a modification of the amplified fragment length polymorphism method (AFLP) based on the differential sensitivity of isoschizomeric restriction enzymes to site-specific cytosine methylation. *The genome of V. cazorlensis plants exhibited extensive levels of methylation, and methylation-based epigenetic variation was structured into distinct between- and within- population components. Epigenetic differentiation of populations was correlated with adaptive genetic divergence revealed by a Bayesian population-genomic analysis of AFLP data. Significant associations existed at the individual genome level between adaptive AFLP loci and the methylation state of methylation-susceptible MSAP loci. *Population-specific, divergent patterns of correlated selection on epigenetic and genetic individual variation could account for the coordinated epigenetic-genetic adaptive population differentiation revealed by this study.

Switch-on fluorescent strategy based on crystal violet-functionalized CdTe quantum dots for detecting L-cysteine and glutathione in water and urine.

Science.gov (United States)

Sheng, Zhen; Chen, Ligang

2017-10-01

The concentration of L-cysteine (Cys) and glutathione (GSH) is closely related to the critical risk of various diseases. In our study, a new rapid method for the determination of Cys and GSH in water and urine samples has been developed using a fluorescent probe technique, which was based on crystal violet (CV)-functionalized CdTe quantum dots (QDs). The original QDs emitted fluorescence light, which was turned off upon adding CV. This conjugation of CV and QDs could be attributed to electrostatic interaction between COO - of mercaptopropionic acid (MPA) on the surface of QDs and N + of CV in aqueous solution. In addition, Förster resonance energy transfer (FRET) also occurred between CdTe QDs and CV. After adding Cys or GSH to the solution, Cys or GSH exhibited a stronger binding preference toward Cd 2+ than Cd 2+ -MPA, which disturbed the interaction between MPA and QDs. Thus, most MPA was able to be separated from the surface of QDs because of the participation of Cys or GSH. Then, the fluorescence intensity of the CdTe QDs was enhanced. Good linear relationships were obtained in the range of 0.02-40 μg mL -1 and 0.02-50 μg mL -1 , and the detection limits were calculated as 10.5 ng mL -1 and 8.2 ng mL -1 , for Cys and GSH, respectively. In addition, the concentrations of biological thiols in water and urine samples were determined by the standard addition method using Cys as the standard; the quantitative recoveries were in the range of 97.3-105.8%, and relative standard deviations (RSDs) ranged from 2.5 to 3.7%. The method had several unique properties, such as simplicity, lower cost, high sensitivity, and environmental acceptability. Graphical abstract Crystal violet-functionalized CdTe quantum dots for detecting L-cysteine and glutathione with switch-on fluorescent strategy.

Development of removal and recovery technique for hexavalent chromium eluted from used magnesia-chrome bricks by tannin particles; Maguneshia kuromu renga kara yoshutsusuru rokka kuromu no tanningeru ni yoru bunri kaishu gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakano, Y. [Tokyo Inst. of Tech., Tokyo (Japan); Kawamoto, E. [TYK Corp., Gifu (Japan); Nakamura, Y.; Hamaguchi, K.; Shirato, W.

1999-11-01

Treatment of waste water containing Cr ( 6 ) was investigated, in which tannin gel adsorbent was used, which is prepared by none-solubilization of tannin being capable to adsorb heavy metals. In the batch treatment test, leachate from magnesia-chrome bricks which contains 116 ppm of Cr ( 6 ) and pH 10.4, was treated by adding the adsorbent by 5% and adjusting at pH 3, consequently, Cr ( 6 ) was reduced less than 0.05 ppm. While, in the treatment of the effluent from cooling of brick cutter, which contains 9.7 ppm of Cr ( 6 ) and pH 9.70, it was confirmed that the proper addition of tannin gel is 1.0-1.5 % and the effect appears in less than 30 minuets of agitation. (NEDO)

Final Test Report: Hexavalent Chrome Free Coatings for Electronics Electromagnetic Interference (EMI) Shielding Effectiveness (SE)

Science.gov (United States)

Kessel, Kurt R.

2016-01-01

The test results for Salt Spray Resistance, Static Heat and Humidity and Marine Environment can be found in Sections 3.1.3.3, 3.1.4.3 and 3.1.5.3 respectively. In summary, both the Metalast TCP and SurTec 650 Type 2 conversion coatings perform very similar to the incumbent Type 1 conversion coating against both 6061 and 5052 aluminum under all three test conditions. Significant prior work was performed to select the aluminum and conversion coating included within this test cycle; Reference - NASA GSDO Program Hexavalent Chrome Alternatives Final Pretreatments Test Report Task Order: NNH12AA45D September 01, 2013. As illustrated in the data, the 6061 aluminum panels SLIGHTLY out-performed the 5052 aluminum panels. Individual shielding effectiveness graphs for each panel are included within Appendix C and D. One other notable effect found during review of the data is that the Test Panels exposed to B117 Salt Fog reduced in shielding effectiveness significantly more than the Marine Environment Test Panels. The shielding effectiveness of the Marine Test Panels was approximately 20dB higher than the Test Panels that underwent B117 Salt Fog Exposure. The intent of this evaluation was not to maximize shielding effectiveness values. The same Parker Chomerics Cho-Seal 6503 gasket material was used for all panels with aluminum and conversion coating variants. A typical EMI gasket design for corrosive environments would be done quite differently. The intent was to execute a test that would provide the best possible evaluation of different aluminum materials and conversion coatings in corrosive environments. The test program achieved this intent. The fact that the two aluminums and two Type II conversion coatings performed similar to the incumbent Type 1 conversion coating is a positive outcome. It was desired to have an outcome that further differentiation the performance of two aluminum types and two conversion coating types but this could not be extracted by the test

Site-occupancy, luminescent properties and energy transfer of a violet-to-red color-tunable phosphor Ca{sub 10}Li(PO{sub 4}){sub 7}: Ce{sup 3+}, Mn{sup 2+}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xinguo, E-mail: mpcc1@qq.com [Guangdong Provincial Key Laboratory of New Drug Screening, School of Pharmaceutical Sciences, Southern Medical University, Guangzhou 510515 (China); Xu, Jungu [Guangxi Ministry-Province Jointly-Constructed Cultivation Base for State Key Laboratory of Processing for Nonferrous Metal and Featured Materials, MOE Key Laboratory of New Processing Technology for Nonferrous Metals and Materials, Guangxi Universities Key Laboratory of Non-ferrous Metal Oxide Electronic Functional Materials and Devices, College of Materials Science and Engineering, Guilin University of Technology, Guilin 541004 (China); Gong, Menglian [School of Chemistry, Sun Yat-Sen University, Guangzhou 510275 (China)

2017-03-15

A series of color-tunable phosphors Ca{sub 10}Li(PO{sub 4}){sub 7}: Ce{sup 3+}, Mn{sup 2+} were synthesized by high-temperature solid-state reaction. Site occupancy of Ce{sup 3+} and Mn{sup 2+} in Ca{sub 10}Li(PO{sub 4}){sub 7} and corresponding luminescent properties were systemically studied. Rietveld refinement results indicate that the Ce{sup 3+} ions are preferred to occupy 7-cooridnated M1 and M3 sites, and Mn{sup 2+} ions are mainly occupying distorted octahedral M5 sites, which results in Ce{sup 3+} violet emission at 370 nm and Mn{sup 2+} red emission at 640 nm. The intensity of Mn{sup 2+} red emission is greatly enhanced through efficient Ce{sup 3+}-Mn{sup 2+} energy transfer (η{sub ET}=94%). The critical distance and corresponding mechanism of Ce{sup 3+}-Mn{sup 2+} energy transfer was found to be ~11 Å and dipole-quadrupole interaction, respectively. The emitting colors of Ca{sub 10}Li(PO{sub 4}){sub 7}: Ce{sup 3+}, Mn{sup 2+} phosphors can be tuned from violet through pink to red by adjusting the Ce{sup 3+}/Mn{sup 2+} ratio. The composition-optimized red phosphor Ca{sub 10}Li(PO{sub 4}){sub 7}: 0.05Ce{sup 3+}, 0.09Mn{sup 2+} exhibits excellent thermal stability at high temperature (~100% at 160 °C).

Electron spin ressonance of radicals produced by ultra-violet photolysis of KCL dopped with potassium cyanide and potassium cyanate

International Nuclear Information System (INIS)

Duran, J.E.R.

1975-01-01

The production of radicals by ultra-violet photolysis of KCL dopped with potassium cyanide and potassium cyanate is studied by electron spin resonance. Several new paramagnetic species are detected which are identified as HCNO - , NCN - /NCNO - , CNN - /CNON - and CNOsup(=) all giving isotropic spectra at 77 0 K. The temperature dependence of the CNOsup(=) spectrum is investigated down to 1.6 0 K. It is found that two different recrientation motions ocurr which freeze at different temperatures. The effect of this motion on the line width is analized using Anderson's theory of exchange narrowing. The electronic structure of the CNOsup(=) radical is discussed using the measured the carbon and nitrogen hfs constants. It is found that a bonding scheme similar to that accepted for the isoelectronic molecule NO 2 is applicable, and a one electron molecular orbital scheme is given. Within this scheme a negative contribution to the nitrogen isotropic hfs constant is found which is assumed to originate from the polarization of the fully occupied ls orbitals [pt

Visible-light driven photocatalytic degradation of methylene-violet by rGO/Fe{sub 3}O{sub 4}/ZnO ternary nanohybrid structures

Energy Technology Data Exchange (ETDEWEB)

Thangavel, Srinivas [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Center of Excellence in Advanced Materials and Green Technologies, Department of Chemical Engineering and Material Science, Amrita Vishwa Vidyapeetham, Coimbatore 641 112, Tamil Nadu (India); Thangavel, Sakthivel [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Department of Mechanical Engineering, Jeju National University, Jeju 690-756 (Korea, Republic of); Raghavan, Nivea [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Krishnamoorthy, Karthikeyan [Department of Mechanical Engineering, Jeju National University, Jeju 690-756 (Korea, Republic of); Venugopal, Gunasekaran, E-mail: gunasekaran@karunya.edu [Nanomaterials Research Lab ( NmRL ), Department of Nanoscience and Technology, Karunya University, Coimbatore 641 114, Tamil Nadu (India); Solid State Electronics Lab, Research Institute of Electrical Communication, Tohoku University, Katahira, Sendai 980-8577 (Japan)

2016-04-25

A novel ternary nanohybrid structure was constructed with reduced graphene-oxide/iron-oxide/zinc-oxide (rGO/Fe{sub 3}O{sub 4}/ZnO) via a facile hydrothermal method. The structural, morphological and optical properties were explored using X-ray diffraction, scanning electron microscope (SEM) with energy dispersive spectra and photoluminescence (PL) studies. The functional groups of ternary nanohybrid were characterized by Fourier transform-infrared spectroscopy. SEM images confirm the presence of two-dimensional GO sheets, one dimensional Fe{sub 3}O{sub 4} and ZnO nanorods. The PL spectra showed the quenching effect which has been observed from the reduction of electron–hole recombination in hybrid. Degradation efficiency of this system was evaluated and compared with pure ZnO and Fe{sub 3}O{sub 4}/ZnO. Under visible light condition, the ternary nanohybrid has shown an excellent photocatalytic degradation of methylene-violet dye. The degradation efficiency of rGO/Fe{sub 3}O{sub 4}/ZnO was systematically analyzed by absorption spectra and total organic carbon removal techniques. Our experimental results will show the potential way for the development of futuristic rGO based nanohybrids as an effective photocatalytic materials for waste-water treatment and environmental remedial applications. - Graphical abstract: A new ternary nanohybrid has been constructed with 1D Fe{sub 3}O{sub 4}–ZnO and 2D rGO sheets to utilize as visible-light photocatalyst. Highly active photocatalyst has been prepared by a feasible hydrothermal approach. For the first time, rGO/Fe{sub 3}O{sub 4}/ZnO ternary nanohybrid exhibits a superior photocatalytic activity towards the degradation of methylene-violet (dye) and the same can be used for environmental remediation applications. - Highlights: • Ternary nanohybrid constructed with 1D ZnO, Fe{sub 3}O{sub 4} and 2D rGO. • Aggregation free rGO/Fe{sub 3}O{sub 4}/ZnO nanohybrid exhibits superior photocatalytic activity. • rGO boost up

Use of Standing Gold Nanorods for Detection of Malachite Green and Crystal Violet in Fish by SERS.

Science.gov (United States)

Chen, Xiaowei; Nguyen, Trang H D; Gu, Liqun; Lin, Mengshi

2017-07-01

With growing consumption of aquaculture products, there is increasing demand on rapid and sensitive techniques that can detect prohibited substances in the seafood products. This study aimed to develop a novel surface-enhanced Raman spectroscopy (SERS) method coupled with simplified extraction protocol and novel gold nanorod (AuNR) substrates to detect banned aquaculture substances (malachite green [MG] and crystal violet [CV]) and their mixture (1:1) in aqueous solution and fish samples. Multivariate statistical tools such as principal component analysis (PCA) and partial least squares regression (PLSR) were used in data analysis. PCA results demonstrate that SERS can distinguish MG, CV and their mixture (1:1) in aqueous solution and in fish samples. The detection limit of SERS coupled with standing AuNR substrates is 1 ppb for both MG and CV in fish samples. A good linear relationship between the actual concentration and predicted concentration of analytes based on PLSR models with R 2 values from 0.87 to 0.99 were obtained, indicating satisfactory quantification results of this method. These results demonstrate that the SERS method coupled with AuNR substrates can be used for rapid and accurate detection of MG and CV in fish samples. © 2017 Institute of Food Technologists®.

Eragrostis plana Nees as a novel eco-friendly adsorbent for removal of crystal violet from aqueous solutions.

Science.gov (United States)

Filho, Augusto Cezar D; Mazzocato, Ana C; Dotto, Guilherme L; Thue, Pascal S; Pavan, Flávio A

2017-08-01

Eragrostis plana Nees (EPN) was used as new and eco-friendly adsorbent for the removal of crystal violet dye (CV) from aqueous solution. Specific surface area (BET), scanning electron microscopy (SEM), infrared spectroscopy (ATR-FTIR), point of zero charge (pH PZC ), and modified Boehm titration method were used to characterize the EPN material. The effects of initial pH of solution, adsorbent mass, contact time and initial dye concentration, and temperature were studied in batch adsorption mode. Kinetic data were evaluated by pseudo-first-order and pseudo-second-order models. The result exhibited that pseudo-second-order model well described the adsorption kinetics of CV onto EPN. Langmuir, Freundlich, and Sips isotherm models were used for analysis of the isothermal data. The equilibrium data of adsorption of CV onto EPN was better fitted with the Sips isotherm. Based on the Sips isotherm model, the maximum adsorption capacity was 76.20 ± 1.20 mg g -1 at 333 K. A high desorption of CV from EPN was obtained using 1.00 mol L -1 of CH 3 COOH as eluent. The thermodynamic data indicated that the adsorption was spontaneous, endothermic, and physical process. EPN can be used as alternative adsorbent to remove CV from aqueous solution.

Tritium Decontamination of TFTR D-T Graphite Tiles Employing Ultra Violet Light and a Nd:YAG Laser

International Nuclear Information System (INIS)

Gentile, C.A.; Skinner, C.H.; Young, K.M.; Ciebiera, L.

1999-01-01

The use of an ultra violet (UV) light source (wavelength = 172 nm) and a Nd:YAG Laser for the decontamination of the Tokamak Fusion Test Reactor (TFTR) deuterium-tritium (D-T) tiles will be investigated at the Princeton Plasma Physics Laboratory (PPPL). The development of this form of tritium decontamination may be useful for future D-T burning fusion devices which employ carbon plasma-facing components on the first wall. Carbon tiles retain hydrogen isotopes, and the in-situ tritium decontamination of carbon can be extremely important in maintaining resident in-vessel tritium inventory to a minimum. A test chamber has been designed and fabricated at PPPL. The chamber has the ability to be maintained under vacuum, be baked to 200 *C, and provides sample ports for gas analyses. Tiles from TFTR that have been exposed to D-T plasmas will be placed within the chamber and exposed to either an UV light source or the ND:YAG Laser. The experiment will determine the effectiveness of these two techniques for the removal of tritium. In addition, exposure rates and scan times for the UV light source and/or Nd:YAG Laser will be determined for tritium removal optimization from D-T tiles

Application potential of grapefruit peel as dye sorbent: Kinetics, equilibrium and mechanism of crystal violet adsorption

International Nuclear Information System (INIS)

Saeed, Asma; Sharif, Mehwish; Iqbal, Muhammad

2010-01-01

This study reports the sorption of crystal violet (CV) dye by grapefruit peel (GFP), which has application potential in the remediation of dye-contaminated wastewaters using a solid waste generated by the citrus fruit juice industry. Batch adsorption of CV was conducted to evaluate the effect of initial pH, contact time, temperature, initial dye concentration, GFP adsorbent dose, and removal of the adsorbate CV dye from aqueous solution to understand the mechanism of sorption involved. Sorption equilibrium reached rapidly with 96% CV removal in 60 min. Fit of the sorption experimental data was tested on the pseudo-first and pseudo-second-order kinetics mathematical equations, which was noted to follow the pseudo-second-order kinetics better, with coefficient of correlation ≥0.992. The equilibrium process was well described by the Langmuir isotherm model, with maximum sorption capacity of 254.16 mg g -1 . The GFP was regenerated using 1 M NaOH, with up to 98.25% recovery of CV and could be reused as a dye sorbent in repeated cycles. GFP was also shown to be highly effective in removing CV from aqueous solution in continuous-flow fixed-bed column reactors. The study shows that GFP has the potential of application as an efficient sorbent for the removal of CV from aqueous solutions.

Batch and continuous (fixed-bed column) biosorption of crystal violet by Artocarpus heterophyllus (jackfruit) leaf powder.

Science.gov (United States)

Saha, Papita Das; Chakraborty, Sagnik; Chowdhury, Shamik

2012-04-01

In this study, batch and fixed-bed column experiments were performed to investigate the biosorption potential of Artocarpus heterophyllus (jackfruit) leaf powder (JLP) to remove crystal violet (CV) from aqueous solutions. Batch biosorption studies were carried out as a function of solution pH, contact time, initial dye concentration and temperature. The biosorption equilibrium data showed excellent fit to the Langmuir isotherm model with maximum monolayer biosorption capacity of 43.39 mg g(-1) at pH 7.0, initial dye concentration=50 mg L(-1), temperature=293 K and contact time=120 min. According to Dubinin-Radushkevich (D-R) isotherm model, biosorption of CV by JLP was chemisorption. The biosorption kinetics followed the pseudo-second-order kinetic model. Thermodynamic analysis revealed that biosorption of CV from aqueous solution by JLP was a spontaneous and exothermic process. In order to ascertain the practical applicability of the biosorbent, fixed-bed column studies were also performed. The breakthrough time increased with increasing bed height and decreased with increasing flow rate. The Thomas model as well as the BDST model showed good agreement with the experimental results at all the process parameters studied. It can be concluded that JLP is a promising biosorbent for removal of CV from aqueous solutions. Copyright © 2011 Elsevier B.V. All rights reserved.

Antiviral activity of gliotoxin, gentian violet and brilliant green against Nipah and Hendra virus in vitro

Directory of Open Access Journals (Sweden)

Meyer Adam G

2009-11-01

Full Text Available Abstract Background Using a recently described monolayer assay amenable to high throughput screening format for the identification of potential Nipah virus and Hendra virus antivirals, we have partially screened a low molecular weight compound library (>8,000 compounds directly against live virus infection and identified twenty eight promising lead molecules. Initial single blind screens were conducted with 10 μM compound in triplicate with a minimum efficacy of 90% required for lead selection. Lead compounds were then further characterised to determine the median efficacy (IC50, cytotoxicity (CC50 and the in vitro therapeutic index in live virus and pseudotype assay formats. Results While a number of leads were identified, the current work describes three commercially available compounds: brilliant green, gentian violet and gliotoxin, identified as having potent antiviral activity against Nipah and Hendra virus. Similar efficacy was observed against pseudotyped Nipah and Hendra virus, vesicular stomatitis virus and human parainfluenza virus type 3 while only gliotoxin inhibited an influenza A virus suggesting a non-specific, broad spectrum activity for this compound. Conclusion All three of these compounds have been used previously for various aspects of anti-bacterial and anti-fungal therapy and the current results suggest that while unsuitable for internal administration, they may be amenable to topical antiviral applications, or as disinfectants and provide excellent positive controls for future studies.

Application potential of grapefruit peel as dye sorbent: kinetics, equilibrium and mechanism of crystal violet adsorption.

Science.gov (United States)

Saeed, Asma; Sharif, Mehwish; Iqbal, Muhammad

2010-07-15

This study reports the sorption of crystal violet (CV) dye by grapefruit peel (GFP), which has application potential in the remediation of dye-contaminated wastewaters using a solid waste generated by the citrus fruit juice industry. Batch adsorption of CV was conducted to evaluate the effect of initial pH, contact time, temperature, initial dye concentration, GFP adsorbent dose, and removal of the adsorbate CV dye from aqueous solution to understand the mechanism of sorption involved. Sorption equilibrium reached rapidly with 96% CV removal in 60 min. Fit of the sorption experimental data was tested on the pseudo-first and pseudo-second-order kinetics mathematical equations, which was noted to follow the pseudo-second-order kinetics better, with coefficient of correlation > or = 0.992. The equilibrium process was well described by the Langmuir isotherm model, with maximum sorption capacity of 254.16 mg g(-1). The GFP was regenerated using 1 M NaOH, with up to 98.25% recovery of CV and could be reused as a dye sorbent in repeated cycles. GFP was also shown to be highly effective in removing CV from aqueous solution in continuous-flow fixed-bed column reactors. The study shows that GFP has the potential of application as an efficient sorbent for the removal of CV from aqueous solutions. 2010 Elsevier B.V. All rights reserved.

Application potential of grapefruit peel as dye sorbent: Kinetics, equilibrium and mechanism of crystal violet adsorption

Energy Technology Data Exchange (ETDEWEB)

Saeed, Asma, E-mail: asmadr@wol.net.pk [Environmental Biotechnology Group, Biotechnology and Food Research Centre, PCSIR Laboratories Complex, Ferozepur Road, Lahore 54600 (Pakistan); Sharif, Mehwish [School of Biological Sciences, University of the Punjab, Lahore 54590 (Pakistan); Iqbal, Muhammad [Environmental Biotechnology Group, Biotechnology and Food Research Centre, PCSIR Laboratories Complex, Ferozepur Road, Lahore 54600 (Pakistan)

2010-07-15

This study reports the sorption of crystal violet (CV) dye by grapefruit peel (GFP), which has application potential in the remediation of dye-contaminated wastewaters using a solid waste generated by the citrus fruit juice industry. Batch adsorption of CV was conducted to evaluate the effect of initial pH, contact time, temperature, initial dye concentration, GFP adsorbent dose, and removal of the adsorbate CV dye from aqueous solution to understand the mechanism of sorption involved. Sorption equilibrium reached rapidly with 96% CV removal in 60 min. Fit of the sorption experimental data was tested on the pseudo-first and pseudo-second-order kinetics mathematical equations, which was noted to follow the pseudo-second-order kinetics better, with coefficient of correlation {>=}0.992. The equilibrium process was well described by the Langmuir isotherm model, with maximum sorption capacity of 254.16 mg g{sup -1}. The GFP was regenerated using 1 M NaOH, with up to 98.25% recovery of CV and could be reused as a dye sorbent in repeated cycles. GFP was also shown to be highly effective in removing CV from aqueous solution in continuous-flow fixed-bed column reactors. The study shows that GFP has the potential of application as an efficient sorbent for the removal of CV from aqueous solutions.

Absolute atomic oxygen and nitrogen densities in radio-frequency driven atmospheric pressure cold plasmas: Synchrotron vacuum ultra-violet high-resolution Fourier-transform absorption measurements

International Nuclear Information System (INIS)

Niemi, K.; O'Connell, D.; Gans, T.; Oliveira, N. de; Joyeux, D.; Nahon, L.; Booth, J. P.

2013-01-01

Reactive atomic species play a key role in emerging cold atmospheric pressure plasma applications, in particular, in plasma medicine. Absolute densities of atomic oxygen and atomic nitrogen were measured in a radio-frequency driven non-equilibrium plasma operated at atmospheric pressure using vacuum ultra-violet (VUV) absorption spectroscopy. The experiment was conducted on the DESIRS synchrotron beamline using a unique VUV Fourier-transform spectrometer. Measurements were carried out in plasmas operated in helium with air-like N 2 /O 2 (4:1) admixtures. A maximum in the O-atom concentration of (9.1 ± 0.7)×10 20 m −3 was found at admixtures of 0.35 vol. %, while the N-atom concentration exhibits a maximum of (5.7 ± 0.4)×10 19 m −3 at 0.1 vol. %

Violet Grove CO{sub 2} injection project : monitoring with timelapse VSP surveys

Energy Technology Data Exchange (ETDEWEB)

Coueslan, M.; Lawton, D. [Calgary Univ., Calgary, AB (Canada); Jones, M. [Schlumberger Canada Ltd., Calgary, AB (Canada)

2006-07-01

Several oil and gas fields in western Canada have been depleted through primary production and secondary recovery methods. Injecting carbon dioxide (CO{sub 2}) into a reservoir can enhance oil recovery (EOR) and has the potential benefit of CO{sub 2} sequestration, which reduces greenhouse gas emissions into the atmosphere. It has been estimated that western Canada has a practical CO{sub 2} storage capacity of about 3.3 Gt in its oil and gas reservoirs. In order to claim a reduction in CO{sub 2} emissions, however, the injected CO{sub 2} must be monitored to prove that it is being trapped in these reservoirs. For that reason, the Violet Grove site, near Drayton Valley, Alberta was chosen as a pilot site to study CO{sub 2} injection into a reservoir for enhanced recovery and carbon sequestration purposes. The reservoir is located in the Cardium Formation in the Pembina Field. It was expected that the CO{sub 2} would flow preferentially in the reservoir's dominant fracture orientation, which is northeast-southwest. Simultaneously acquired time-lapse multicomponent surface and borehole seismic surveys were used to monitor changes in the reservoir. Prior to CO{sub 2} injection, a baseline survey was acquired in March 2005. A second survey was acquired 8 months after CO{sub 2} injection. The borehole seismic data displayed higher bandwidth and increased resolution compared to the surface seismic data. The PS-wave borehole seismic data in particular showed much better results. Together, these seismic surveys provide lateral coverage of the area as well as high resolution images near the observation well. Preliminary results from the time-lapse analysis show an increase of 30 to 60 per cent in the reservoir reflectivity amplitudes in the 8 months between the baseline and monitor surveys, suggesting that the CO{sub 2} flood has progressed southwest of the injector, most likely along the dominant fracture trend. 7 refs., 5 figs.

Low Hydrogen Embrittlement (LHE) Zinc-Nickel (Zn-Ni) Qualification Test Result and Process Parameters Development

Science.gov (United States)

2011-02-09

t ~~ Stress Loads (KSI) R= -0.3 Total Shotpeened Coupons 160 180 200 Quantity Bare 5 5 5 15 Cad Plated 5 5 5 15 ~n-Ni Plated Tri Chrome 5 5 5 15...n-Ni Plated Hex Chrome 5 5 5 15 ~Zn·Ni Plated Atotech Tri Chrome 5 5 5 15 ~n-Ni Plated Atotech Hex Chrome 5 5 5 15 Total Fatigue Coupons 90 fk...conversion coating (CC) ( Hexavalent vs. Trivalent) and parameters: ▪ Baking before and after conversion coating • Hexavalent CC: must be applied

Ultra-violet absorption cross sections of isotopically substituted nitrous oxide species: 14N14NO, 15N14NO, 14N15NO and 15N15NO

Directory of Open Access Journals (Sweden)

P. von Hessberg

2004-01-01

Full Text Available The isotopically substituted nitrous oxide species 14N14NO, 15N14NO, 14N15NO and 15N15NO were investigated by ultra-violet (UV absorption spectroscopy. High precision cross sections were obtained for the wavelength range 181 to 218nm at temperatures of 233 and 283K. These data are used to calculate photolytic isotopic fractionation constants as a function of wavelength. The fractionation constants were used in a three-dimensional chemical transport model in order to simulate the actual fractionation of N2O in the stratosphere, and the results were found to be in good agreement with field studies.

Daur ulang bahan penyamak krom

Directory of Open Access Journals (Sweden)

Bambang Oetojo

1994-08-01

Full Text Available Reusing of waste chrome to minimize the pollutant is the purpose of this study. Nevertheless the leather output must be fulfill the standard. For each treatment used, three sides of cow hide with twice replications. The treatment was nine time done. Before the waste chrome liquor was used for tanning it must be adjusted for the quantity of the flood, the pH and the, consenteration. Ther more 7% basic chrome-sulphate base on the pelt weight was added. The leathers out put were visual investigated, and chemically analysed. The waste chrome liquor was chemically analysed. Statistically analyse point out that there is no significance different (P ≤ 0.05 degree of Cr2O3 either in the leather or in the waste chrome liquor due to the treatment. Degree of Cr2O3 of the leather revolve from 3,17 up to 3,82%, whereas degree of, Cr2O3 of the liquor revolve from 7,81%, up to, 13,4 gram per litre. Visual investigation and physical testing point out that the leathers output fulfill the standard. Practical meaning of the study are waste chrome liquor may be reused for tanning by adding 7 % basic chrome sulphate and the leather output fulfill the standard.

Transfer of metallic debris from the metal surface of an acetabular cup to artificial femoral heads by scraping: comparison between alumina and cobalt-chrome heads.

Science.gov (United States)

Chang, Chong Bum; Yoo, Jeong Joon; Song, Won Seok; Kim, Deug Joong; Koo, Kyung-Hoi; Kim, Hee Joong

2008-04-01

We aimed to investigate the transfer of metal to both ceramic (alumina) and metal (cobalt-chrome) heads that were scraped by a titanium alloy surface under different load conditions. The ceramic and metal heads for total hip arthroplasties were scraped by an acetabular metal shell under various loads using a creep tester. Microstructural changes in the scraped area were visualized with a scanning electron microscope, and chemical element changes were assessed using an energy dispersive X-ray spectrometry. Changes in the roughness of the scraped surface were evaluated by a three-dimensional surface profiling system. Metal transfer to the ceramic and metal heads began to be detectable at a 10 kg load, which could be exerted by one-handed force. The surface roughness values significantly increased with increasing test loads in both heads. When the contact force increased, scratching of the head surface occurred in addition to the transfer of metal. The results documented that metallic debris was transferred from the titanium alloy acetabular shell to both ceramic and metal heads by minor scraping. This study suggests that the greatest possible effort should be made to protect femoral heads, regardless of material, from contact with metallic surfaces during total hip arthroplasty.

Kajian penerapan recycle, reuse dan recovery untuk proses produksi kulit web blue pada industri penyamakan kulit

Directory of Open Access Journals (Sweden)

Prayitno Prayitno

2009-06-01

Full Text Available Leather tanning industries are industries that process skin to produce finish leather product by using many stages of process in which for every stage of process will generate a huge amount either liquid or solid waste. If waste are not to be treated properly, it will cause environmental pollution. Implementation of 3R programs i.e. recycle, reuse and recovery will give impact on minimizing of waste problem. In leather tanning industries for producing wet blue leather however, 3R programs have to be implemented in processes of desalting, washing liquor, flesh and fat, chrome liquor and chrome-tanned waste. In implementing 3 R the waste generated can be either reused, recycled or recoveried as follow salt as swelling agent preventing in pickling process; washing liquor waste as washing liquor for dirt washing; flesh and fat as raw material for producing tallow, soap, fertilizer and livestock fodder; chrome liquor waste as chrome agent for chrome tanning and chrome-tanned waste as filler for producing material building or livestock fodder as protein sources.

Ultraviolet (UV)-Curable Coatings for Aerospace Applications

Science.gov (United States)

2012-08-31

implement hexavalent chromium reduction, any new primers introduced would have to be chrome -free. Formulating a chrome -free primer that can provide...5955 All painting was done on panels of 2024-T3 Aluminum (4" x 6" x 0.020") with ¼” hole in center of short side, coated with an Alodine 1200S chrome

The effect of gamma - Radiation on the degradation of a diazo dye (diamine brilliant violet B ) in aqueous solutions

International Nuclear Information System (INIS)

El-Assy, N.B.; Abdel-Fattah, A.A.

1986-01-01

The effect of gamma radiation on the color intensity of aerated o 2-saturated and N 2-saturated aqueous solutions of diamine brilliant violet B (D B V B) was investigated. The studies of the absorption spectra show that the de coloration of the dye is promoted by the presence of oxygen and that the framework of the chromophores is destroyed almost completely at 2.9 KGy for concentration 4.75 x 10-2 g/L in the presence of oxygen. The kinetics of deceleration of solutions of (D B V B) turned out to be of the first order with respect to the dye concentration (from 0.02 to 0.1 g/L). The change of pH through the irradiation process was followed and it was found that,the ph of the solution decreased by increasing the dose, indicating that, the degradation of the dye molecule was accompanied by the formation of some organic acids especially in the presence of oxygen. The Gd-values for different initial concentrations at different doses were tabulated and a scheme for the deceleration process was proposed

Detection of hazardous pollutants in chrome-tanned leather using locally developed laser-induced breakdown spectrometer.

Science.gov (United States)

Nasr, M M; Gondal, Mohammed Asharf; Seddigi, Z S

2011-04-01

Highly toxic contaminants like Cr, As, and Pb were detected in chrome-tanning process of animal skin to produce leather by applying locally developed laser-induced breakdown spectrometer. An Nd-YAG laser with 1,064 nm wavelength was focused on the surface of leather samples (natural and manufactured) to generate a plasma spark and spectrally resolved spectra were used for identification and quantification of contaminants. The leather samples were collected from a tannery located in industrial cities of Riyadh and Jeddah, Saudi Arabia. The study was carried out on fully, half manufactured (wet blue leather), and natural hide (skin). To the best of our knowledge, this is the first attempt where laser-induced breakdown spectroscopy (LIBS) technique has been applied for the analysis of leather before and after tanning process. The maximum concentration of different elements of environmental significance like chromium, lead, arsenic, sulfur, magnesium were 199, 289, 31, 38, and 39 ppm, respectively, in one of the manufactured leather samples. The limit of detection (LOD) of our LIBS system for chromium, lead, arsenic, sulfur, and magnesium were 2, 3, 1.5,7, and 3 ppm, respectively. The safe permissible limit for tanned leather for highly toxic elements like chromium, lead, and arsenic are 1, 0.5, 0.01 ppm, respectively, as prescribed in Environmental Regulation Standards for Saudi Industries set by Royal Commission Jubail, Saudi Arabia. The LIBS technique is superior to other conventional techniques like ICP or atomic absorption that a little or no sample preparation is required, no chemicals are needed, multi-elemental analysis is possible for all kinds of samples (natural and anthropogenic materials), microgram of sample is essential, and LIBS could be applied for remote analysis. It is highly selective and sensitivity higher than ICP, and as no sample and chemicals are required, it is cost effective for multi-sample analysis per unit time as compared with other

Tritium decontamination from co-deposited layer on tungsten substrate by ultra violet lamp and laser

International Nuclear Information System (INIS)

Oya, Yasuhisa; Tadokoro, Takahiro; Shu, Wataru; Hayashi, Takumi; O'hira, Shigeru; Nishi, Masataka

2001-01-01

Tritium decontamination using ultra violet (UV) lamp and laser was performed. Simulated co-deposited layer on tungsten substrate was deposited by C 2 H 2 or C 2 D 2 glow discharge. The co-deposited layer was irradiated to UV lights from a xenon excimer lamp (172 nm) or ArF excimer laser (193 nm) and the in-situ decontamination behavior was evaluated by a mass spectrometer. After the UV irradiation, the hydrogen concentration in the co-deposited layer was evaluated by elastic recoil detection analysis (ERDA) and the depth profile was analyzed by secondary ion mass spectrometry (SIMS). For the co-deposited layer formed by C 2 D 2 glow discharge, it was found that M/e 3 (HD) gas was released mainly during the UV lamp irradiation while both M/e 3 (HD) and M/e 4 (D 2 ) gases were detected during the UV laser irradiation. Though the co-deposited layer was not removed by UV lamp irradiation, almost all the co-deposited layer was removed by UV laser irradiation within 1 min. The ratio of hydrogen against carbon in the co-deposited layer was estimated to be 0.53 by ERDA and the number of photon needed for removing 1 μm thick co-deposited layer was calculated to be 3.7x10 18 cm -2 for the UV laser by SIMS measurement. It is concluded that C-H (C-D) bond on the co-deposited layer were dissociated by irradiation of UV lamp while the co-deposited layer itself was removed by the UV laser irradiation. (author)

Adsorption Properties of PVA/PAA/clay Composite Hydrogel Synthesized by Gamma Radiation and its Application in Removal of Crystal Violet Dye from Its Aqueous Solution

International Nuclear Information System (INIS)

Kamal, H.; El-Sayed, A. Hegazy; Mohamed, M.M.; Sabaa, M.W.; El-Dessouky, M.M.

2014-01-01

Copolymer hydrogels composed of Poly vinyl alcohol (PVA) and Poly acrylic acid (PAA) were prepared by γ-irradiation in the presence of N,N’ methylene bis acrylamide (MBAM) as crosslinking agent or bentonite clay. The copolymers were characterized by FTIR and SEM. The dye adsorption experiments for Crystal Violet dye (CV) were carried out by using bath procedure. UV-visible absorption spectroscopy was used to determine the adsorption behavior. The effect of different copolymer composition, clay concentration, ph, contact time, adsorbent dose, initial dye concentration, and adsorption temperature were investigated to obtain the best experimental conditions. The adsorption equilibrium was attained after about 24h. of contact time. It was found that the adsorption process was correlated with Freundlich isotherm equation. Kinetic and thermodynamic studies of CV dye onto the prepared hydrogels were also evaluated

Effect of low doses of ionizing radiation, azoxystrobin and selected heavy metals on the model organism of species Artemia franciscana; Posobenie nizkych davok ionizujuceho ziarenia, azoxystrobinu a vybranych tazkych kovov na modelovy organizmus druhu Artemia franciscana

Energy Technology Data Exchange (ETDEWEB)

Spalkova, M.; Danova, D. [Univerzita veterinarskeho lekarstva a farmacie, Katedra biologie a genetiky, Ustav biologie, zoologie a radiobiologie, 04181 Kosice (Slovakia); Falis, M. [Univerzita veterinarskeho lekarstva a farmacie, Katedra farmakologie a toxikologie, Ustav toxikologie, 04181 Kosice (Slovakia); Zdarsky, M. [Veterinarni a farmaceuticka univerzita Brno, Ustav biochemie, chemie a biofyziky, 61242 Brno (Czech Republic)

2013-04-16

The aim of our study was to observe the effect of low doses of ionizing radiation, azoxystrobin, zinc and chrome on the lethality of Artemia franciscana. Significant increase of the lethality was observed after 72 and 96 hours of exposure to azoxystrobin and chrome as well as to azoxystrobin, chrome and irradiation. On the other hand, we observed significant decrease of the lethality in the groups exposed to pesticide and chrome or pesticide and zinc in combination with ionizing radiation with the dose of 50 Gy at time interval of 96 hours in comparison to non-irradiated groups. (authors)

Non-Chromate, ZVOC Coatings for Steel Substrates on Army and Navy Aircraft and Ground Vehicles

Science.gov (United States)

2014-12-01

been coated without any corrosion inhibitive pretreatment or conversion coating. The products demonstrated satisfy the hexavalent chrome ...that generates 2.4 million pounds of VOC; 852,000 pounds of HAPs; and 24,000 pounds of hexavalent chrome . Although effective at mitigating corrosion...satisfy the hexavalent chrome prohibition for both vehicles while minimizing environmental impact and promoting worker safety. This demonstration was

[The study of the colorimetric characteristics of the cobalt-chrome alloys abutments covered by four different all-ceramic crowns by using dental spectrophotometer].

Science.gov (United States)

Chen, Yifan; Liu, Hongchun; Meng, Yukun; Chao, Yonglie; Liu, Changhong

2015-06-01

This study aims to evaluate the optical data of the different sites of the cobalt-chrome (Co-Cr) alloy abutments covered by four different all-ceramic crowns and the color difference between the crowns and target tab using a digital dental spectrophotometer. Ten Co-Cr alloy abutments were made and tried in four different groups of all-ceramic crowns, namely, Procera aluminia, Procera zirconia, Lava zirconia (Lava-Zir), and IPS E.max glass-ceramic lithium disilicate-reinforced monolithic. The color data of the cervical, body, and incisal sites of the samples were recorded and analyzed by dental spectrophotometer. The CIE L*, a*, b* values were again measured after veneering. The color difference between the abutments covered by all-ceramic crowns and A2 dentine shade tab was evaluated. The L* and b* values of the abutments can be increased by all of the four groups of all-ceramic copings, but a* values were decreased in most groups. A statistical difference was observed among four groups. After being veneered, the L* values of all the copings declined slightly, and the values of a*, b* increased significantly. When compared with A2 dentine shade tab, the ΔE of the crowns was below 4. Four ceramic copings were demonstrated to promote the lightness and hue of the alloy abutments effecttively. Though the colorimetric baseline of these copings was uneven, veneer porcelain can efficiently decrease the color difference between the samples and thee target.

Is ultra-violet radiation the main force shaping molecular evolution of varicella-zoster virus?

Science.gov (United States)

2011-01-01

Background Varicella (chickenpox) exhibits a characteristic epidemiological pattern which is associated with climate. In general, primary infections in tropical regions are comparatively less frequent among children than in temperate regions. This peculiarity regarding varicella-zoster virus (VZV) infection among certain age groups in tropical regions results in increased susceptibility during adulthood in these regions. Moreover, this disease shows a cyclic behavior in which the number of cases increases significantly during winter and spring. This observation further supports the participation of environmental factors in global epidemiology of chickenpox. However, the underlying mechanisms responsible for this distinctive disease behavior are not understood completely. In a recent publication, Philip S. Rice has put forward an interesting hypothesis suggesting that ultra-violet (UV) radiation is the major environmental factor driving the molecular evolution of VZV. Discussion While we welcomed the attempt to explain the mechanisms controlling VZV transmission and distribution, we argue that Rice's hypothesis takes lightly the circulation of the so called "temperate VZV genotypes" in tropical regions and, to certain degree, overlooks the predominance of such lineages in certain non-temperate areas. Here, we further discuss and present new information about the overwhelming dominance of temperate VZV genotypes in Mexico regardless of geographical location and climate. Summary UV radiation does not satisfactorily explain the distribution of VZV genotypes in different tropical and temperate regions of Mexico. Additionally, the cyclic behavior of varicella does not shown significant differences between regions with different climates in the country. More studies should be conducted to identify the factors directly involved in viral spreading. A better understanding of the modes of transmissions exploited by VZV and their effect on viral fitness is likely to facilitate

Is ultra-violet radiation the main force shaping molecular evolution of varicella-zoster virus?

Directory of Open Access Journals (Sweden)

Escobar-Gutiérrez Alejandro

2011-07-01

Full Text Available Abstract Background Varicella (chickenpox exhibits a characteristic epidemiological pattern which is associated with climate. In general, primary infections in tropical regions are comparatively less frequent among children than in temperate regions. This peculiarity regarding varicella-zoster virus (VZV infection among certain age groups in tropical regions results in increased susceptibility during adulthood in these regions. Moreover, this disease shows a cyclic behavior in which the number of cases increases significantly during winter and spring. This observation further supports the participation of environmental factors in global epidemiology of chickenpox. However, the underlying mechanisms responsible for this distinctive disease behavior are not understood completely. In a recent publication, Philip S. Rice has put forward an interesting hypothesis suggesting that ultra-violet (UV radiation is the major environmental factor driving the molecular evolution of VZV. Discussion While we welcomed the attempt to explain the mechanisms controlling VZV transmission and distribution, we argue that Rice's hypothesis takes lightly the circulation of the so called "temperate VZV genotypes" in tropical regions and, to certain degree, overlooks the predominance of such lineages in certain non-temperate areas. Here, we further discuss and present new information about the overwhelming dominance of temperate VZV genotypes in Mexico regardless of geographical location and climate. Summary UV radiation does not satisfactorily explain the distribution of VZV genotypes in different tropical and temperate regions of Mexico. Additionally, the cyclic behavior of varicella does not shown significant differences between regions with different climates in the country. More studies should be conducted to identify the factors directly involved in viral spreading. A better understanding of the modes of transmissions exploited by VZV and their effect on viral

Boron nitride stamp for ultra-violet nanoimprinting lithography fabricated by focused ion beam lithography

International Nuclear Information System (INIS)

Altun, Ali Ozhan; Jeong, Jun-Ho; Rha, Jong-Joo; Kim, Ki-Don; Lee, Eung-Sug

2007-01-01

Cubic boron nitride (c-BN) is one of the hardest known materials (second after diamond). It has a high level of chemical resistance and high UV transmittance. In this study, a stamp for ultra-violet nanoimprint lithography (UV-NIL) was fabricated using a bi-layered BN film deposited on a quartz substrate. Deposition of the BN was done using RF magnetron sputtering. A hexagonal boron nitride (h-BN) layer was deposited for 30 min before c-BN was deposited for 30 min. The thickness of the film was measured as 160 nm. The phase of the c-BN layer was investigated using Fourier transform infrared (FTIR) spectrometry, and it was found that the c-BN layer has a 40% cubic phase. The deposited film was patterned using focused ion beam (FIB) lithography for use as a UV-NIL stamp. Line patterns were fabricated with the line width and line distance set at 150 and 150 nm, respectively. The patterning process was performed by applying different currents to observe the effect of the current value on the pattern profile. The fabricated patterns were investigated using AFM, and it was found that the pattern fabricated by applying a current value of 50 picoamperes (pA) has a better profile with a 65 nm line depth. The UV transmittance of the 160 nm thick film was measured to be 70-86%. The hardness and modulus of the BN was measured to be 12 and 150 GPa, respectively. The water contact angle of the stamp surface was measured at 75 0 . The stamp was applied to UV-NIL without coating with an anti-adhesion layer. Successful imprinting was proved via scanning electron microscope (SEM) images of the imprinted resin

Synthesis, characterisation of polyaniline-Fe3O4 magnetic nanocomposite and its application for removal of an acid violet 19 dye

Science.gov (United States)

Patil, Manohar R.; Khairnar, Subhash D.; Shrivastava, V. S.

2016-04-01

The present work deals with the development of a new method for the removal of dyes from an aqueous solution using polyaniline (PANI)-Fe3O4 magnetic nanocomposite. It is synthesised in situ through self-polymerisation of monomer aniline. Photocatalytic degradation studies were carried out for cationic acid violet 19 (acid fuchsine) dye using PANI-Fe3O4 nanocomposite in aqueous solution. Different parameters like catalyst dose, contact time and pH have been studied to optimise reaction condition. The optimum conditions for the removal of the dye are initial concentration 20 mg/l, adsorbent dose 6 gm/l, pH 7. The EDS technique gives elemental composition of synthesised PANI-Fe3O4. The SEM and XRD studies were carried for morphological feature characteristics of PANI-Fe3O4 nanocomposite. The VSM (vibrating sample magnetometer) gives magnetic property of PANI-Fe3O4 nanocomposite; also FT-IR analysis gives characteristics frequency of synthesised PANI-Fe3O4. Besides the above studies kinetic study has also been carried out.

Osseointegration and biocompatibility of different metal implants - a comparative experimental investigation in sheep

Science.gov (United States)

2012-01-01

Background In the present study, 4 different metallic implant materials, either partly coated or polished, were tested for their osseointegration and biocompatibility in a pelvic implantation model in sheep. Methods Materials to be evaluated were: Cobalt-Chrome (CC), Cobalt-Chrome/Titanium coating (CCTC), Cobalt-Chrome/Zirconium/Titanium coating (CCZTC), Pure Titanium Standard (PTST), Steel, TAN Standard (TANST) and TAN new finish (TANNEW). Surgery was performed on 7 sheep, with 18 implants per sheep, for a total of 63 implants. After 8 weeks, the specimens were harvested and evaluated macroscopically, radiologically, biomechanically (removal torque), histomorphometrically and histologically. Results Cobalt-Chrome screws showed significantly (p = 0.031) lower removal torque values than pure titanium screws and also a tendency towards lower values compared to the other materials, except for steel. Steel screws showed no significant differences, in comparison to cobalt-chrome and TANST, however also a trend towards lower torque values than the remaining materials. The results of the fluorescence sections agreed with those of the biomechanical test. Histomorphometrically, there were no significant differences of bone area between the groups. The BIC (bone-to-implant-contact), used for the assessment of the osseointegration, was significantly lower for cobalt-chrome, compared to steel (p = 0.001). Steel again showed a lower ratio (p = 0.0001) compared to the other materials. Conclusion This study demonstrated that cobalt-chrome and steel show less osseointegration than the other metals and metal-alloys. However, osseointegration of cobalt-chrome was improved by zirconium and/or titanium based coatings (CCTC, TANST, TAN, TANNEW) being similar as pure titanium in their osseointegrative behavior. PMID:22400715

Alternatives To Cadmium Plated Military Connectors

Science.gov (United States)

2011-08-30

from Feb 2011 Asets Defense conference  Amphenol Aerospace Operations report. 9/21/2011 10 Chromate finish  Hexavalent chrome was targeted by DOD...Fluorocarbon Zinc-Nickel Pure Dense Aluminum  Zinc-Nickel and Aluminum currently contain hexavalent chromate. Nickel-Fluorocarbon requires no...to lack of available drop in replacements, but this will change as alternatives become available.  Trivalent chrome and other non- chrome

Study of Surface Enhanced Raman Scattering of Alizarin and Crystal Violet Dyes

Science.gov (United States)

Gopal, Ram; Swarnkar, Raj Kumar

2010-06-01

Surface enhanced Raman scattering (SERS) plays a vital role in analytical chemistry to characterize ultra trace quantity of organic compounds and biological samples. Two mechanisms have been considered to explain the SERS effect. The main contribution arises from a huge enhancement of the local electromagnetic field close to surface roughness of the metal structures, due to the excitation of a localized surface plasmon, while a further enhancement can be observed for molecules adsorbed onto specific sites when resonant charge transfer occurs. SERS signals have been observed from adsorbates on many metallic surfaces like Ag, Au, Ni, Cu etc. Additionally, metal oxide nanoparticles also show SERS signals It has now been established that SERS of analyte material is highly dependent on the type of substrate involved. Many types of nanostructures like nanofilms, nanorods, nanospheres etc. show highly efficient SERS signals. In particular, there are two routes available for the synthesis of these nanomaterials: the chemical route and the physical route. Chemical route involves many types of reducing agents and capping agents which can interfere in origin and measurement of these signals. The physical route avoids these anomalies and therefore it is suitable for the study of SERS phenomenon. Pulsed laser ablation in liquid medium is an excellent top down technique to produce colloidal solution of nanoparticles with desired shape and size having surface free from chemical contamination, which is essential requirement for surface application of nanoparticles. The present work deals with the study of SERS of Crystal violet dye and Alizarin group dye on Cu@ Cu_2O and Ag colloidal nanoparticles synthesized by pulsed laser ablation. M. Fleishchmann, P. J. Hendra, and A. J. McQuillian Chem. Phys. Lett., 26, 163, 1974. U. Wenning, B. Pettinger, and H. Wetzel Chem. Phys. Lett., 70, 49, 1980. S. C. Singh, R. K. Swarnkar, P. Ankit, M. C. Chattopadhyaya, and R. Gopal AIP Conf. Proc

Violet-to-Blue Gain and Lasing from Colloidal CdS Nanoplatelets: Low-Threshold Stimulated Emission Despite Low Photoluminescence Quantum Yield

Energy Technology Data Exchange (ETDEWEB)

Diroll, Benjamin T.; Talapin, Dmitri V.; Schaller, Richard D.

2017-02-13

Amplified spontaneous emission (ASE) and lasing from solution-processed materials are demonstrated in the challenging violet-to-blue (430–490 nm) spectral region for colloidal nanoplatelets of CdS and newly synthesized core/shell CdS/ZnS nanoplatelets. Despite modest band-edge photoluminescence quantum yields of 2% or less for single excitons, which we show results from hole trapping, the samples exhibit low ASE thresholds. Furthermore, four-monolayer CdS samples show ASE at shorter wavelengths than any reported film of colloidal quantum-confined material. This work underlines that low quantum yields for single excitons do not necessarily lead to a poor gain medium. The low ASE thresholds originate from negligible dispersion in thickness, large absorption cross sections of 2.8 × 10–14 cm–2, and rather slow (150 to 300 ps) biexciton recombination. We show that under higher-fluence excitation, ASE can kinetically outcompete hole trapping. Using nanoplatelets as the gain medium, lasing is observed in a linear optical cavity. This work confirms the fundamental advantages of colloidal quantum well structures as gain media, even in the absence of high photoluminescence efficiency.

Penurunan bahan pencemar dalam air limbah samak krom dengan eceng gondok (Eichornia crassipes Solms

Directory of Open Access Journals (Sweden)

Ignatius Sunaryo

1992-12-01

Full Text Available This research is meant to know the capability of Eichornia crassipes in reducing pollutant in chrome tanning waste water. E. crassipes having the same condition was collected from a pool in Gambiran, Yogyakarta. Then those plants were put down into the media contaning chrome tanning waste water with 0, 5, 10, 15 and 20 ml per litre ground water. The chrome tanning waste water was taken from Leather Tanning Process Labolatory, IRDLAI, Yogyakarta. Based on laboratory research it was found that E. crassipes was able to reduce pollutant in chrome tanning waste water ranging from 2.5 up to 87%. Those values were as follows : COD : 2.5 – 41%; C1 : 14 – 63.5%; S:44-87% total Cr : 55.5 – 77% and total Cr : 55.5 – 77%. E. crassipes which had decrease efficiency of C1, S and Cr effectively were the treatments using chrome tanning waste water with 5, 10 and 15 ml per litre ground water.

A spectroscopic study on the effect of ultra-violet solar radiation in Antarctica on the human skin fibroblast cells

Directory of Open Access Journals (Sweden)

Tatsuyuki Yamamoto

2013-11-01

Full Text Available A study on the effect of the solar ultra-violet radiation on the human skin fibroblast cells revealed that the production of matrix metalloproteinase-2 was inhibited by the radiation. A CO2 incubator connected by optical fibers to a reflector telescope for collecting the solar light was built at Syowa station by the 49th Japanese Antarctica Research Expedition. The direction of the telescope was continuously controlled by a sun-tracker to follow the movement of the Sun automatically. The intensity of the collected light was monitored by a portable spectrophotometer housed inside. The human skin fibroblast cells were incubated in the CO2 chamber to investigate the effect of the solar radiation at Syowa station and were compared with those reference experiments at a laboratory in Japan. The results showed cell damage by strong UV radiation. The production of matrix metalloproteinase-2 was prompted by the moderate UV-B, but was inhibited by the strong UV-B radiation, as studied under laboratory conditions in Japan. The effect of strong solar radiation at Syowa station involving the radiation of UV-B region was estimated to be of the same extent of the radiation caused by an artificial UV-B light with the intensity more than 50 mJ/cm2.

A new rapid colourimetric method for testing Mycobacterium tuberculosis susceptibility to isoniazid and rifampicin: a crystal violet decolourisation assay

Directory of Open Access Journals (Sweden)

Ahmet Yilmaz Coban

2014-04-01

Full Text Available The aim of this study was to investigate the performance of a new and accurate method for the detection of isoniazid (INH and rifampicin (RIF resistance among Mycobacterium tuberculosis isolates using a crystal violet decolourisation assay (CVDA. Fifty-five M. tuberculosis isolates obtained from culture stocks stored at -80ºC were tested. After bacterial inoculation, the samples were incubated at 37ºC for seven days and 100 µL of CV (25 mg/L stock solution was then added to the control and sample tubes. The tubes were incubated for an additional 24-48 h. CV (blue/purple was decolourised in the presence of bacterial growth; thus, if CV lost its colour in a sample containing a drug, the tested isolate was reported as resistant. The sensitivity, specificity, positive predictive value, negative predictive value and agreement for INH were 92.5%, 96.4%, 96.1%, 93.1% and 94.5%, respectively, and 88.8%, 100%, 100%, 94.8% and 96.3%, respectively, for RIF. The results were obtained within eight-nine days. This study shows that CVDA is an effective method to detect M. tuberculosis resistance to INH and RIF in developing countries. This method is rapid, simple and inexpensive. Nonetheless, further studies are necessary before routine laboratory implementation.

40 CFR 415.342 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... SOURCE CATEGORY Chrome Pigments Production Subcategory § 415.342 Effluent limitations guidelines... available (BPT): Subpart AH—Chrome Pigments Pollutant or pollutant property BPT effluent limitations Maximum...

Acquisition Documentation Streamlining, the SEP, and the PESHE

Science.gov (United States)

2012-05-21

identifying any other ESOH requirements (e.g., ban on use of Ozone Depleting Substances or hexavalent chrome )  "Description/Comments:" Use 2-3...limitations on use of hexavalent chrome )  "Description/Comments:" Use 2-3 paragraphs to describe the strategy for integrating ESOH into SE processes...optional tasks) and identifying any other ESOH requirements (e.g., ban on use of Ozone Depleting Substances or hexavalent chrome )  "Description

C-130 Corrosion Prevention and Control Program

Science.gov (United States)

2011-08-01

hexavalent chrome … Warner Robins Air Logistics Center People First…Mission Always SIBR Projects  Back Scatter X-Ray NDI  Detect concealed...Projects Listing Future Projects  Chrome -Free Coating Systems Flight Tests • AkzoNobel (Sep-Oct 2011) – PreKote – Aerodur 2100 magnesium rich...primer (MgRP) – Aerodur 5000 topcoat color #36173 • Deft (June 2012) – Rare earth conversion coating (RECC) 1015/3021 – 02-GN-093 chrome -free

Replacement of Chromium Electroplating on C-2, E-2, P-3 and C-130 Propeller Hub Components Using HVOF Thermal Spray Coatings

National Research Council Canada - National Science Library

Sartwell, Bruce

2004-01-01

.... However, chrome plating utilizes hexavalent chromium, winch is a highly toxic carcinogen, and increasingly stringent environmental and worker-safety regulations are making chrome plating more expensive for the DoD...

Replacement of Chromium Electroplating on Gas Turbine Engine Components Using Thermal Spray Coatings

National Research Council Canada - National Science Library

Sartwell, Bruce D; Legg, Keith O; Schell, Jerry; Bondaruk, Bob; Alford, Charles; Natishan, Paul; Lawrence, Steven; Shubert, Gary; Bretz, Philip; Kaltenhauser, Anne

2005-01-01

.... However, chrome plating utilizes hexavalent chromium, which is a highly toxic carcinogen, and increasingly, stringent environmental and worker-safety regulations are making chrome plating more expensive for the DoD...

Biological and chemical removal of Cr(VI) from waste water: cost and benefit analysis.

Science.gov (United States)

Demir, Aynur; Arisoy, Münevver

2007-08-17

The objective of the present study is cost and benefit analysis of biological and chemical removal of hexavalent chromium [Cr(VI)] ions. Cost and benefit analysis were done with refer to two separate studies on removal of Cr(VI), one of heavy metals with a crucial role concerning increase in environmental pollution and disturbance of ecological balance, through biological adsorption and chemical ion-exchange. Methods of biological and chemical removal were compared with regard to their cost and percentage in chrome removal. According to the result of the comparison, cost per unit in chemical removal was calculated 0.24 euros and the ratio of chrome removal was 99.68%, whereas those of biological removal were 0.14 and 59.3% euros. Therefore, it was seen that cost per unit in chemical removal and chrome removal ratio were higher than those of biological removal method. In the current study where chrome removal is seen as immeasurable benefit in terms of human health and the environment, percentages of chrome removal were taken as measurable benefit and cost per unit of the chemicals as measurable cost.

Investigations on chemical-physical conditioning of ashes from the incineration of sewage sludge to deposit on surface landfill site; Untersuchungen zur Chemisch-Physikalischen Behandlung von Klaerschlammverbrennungsasche zur Ablagerung auf oberirdischen Deponien

Energy Technology Data Exchange (ETDEWEB)

Schneider, O.; Becker, A. [Technische Univ. Kaiserslautern (Germany). Fachgebiet Bodenmechanik und Grundbau; Scherer, G. [TERRAG Service und Vertrieb GmbH, Homburg (Germany)

2007-06-15

Depositing of ashes from the incineration of sewage sludge on landfill is possible after conditioning or within appropriate boxes. The partial high content of chromate- and dichromate- (chrome VI) concentration in the eluate of these slags can cause some difficulties. Presently, disposal of such slags is accomplished in underground spaces. Taking into account the provisions of national laws, possibility is limited. Therefore investigations on deposing of conditioned slags on surface landfills are of growing importance. The binders added to condition the incineration slags were chosen to assess the chemical change of hexavalent chrome (chrome VI) to indissoluble chrome (chrome III). Cement, SAV-residues as well as fly ash were taken as binders. The investigations presented refer to results on mechanical behaviour of conditioned slags. Emphasis is placed on the time-dependent behaviour of strength as well as on water permeability. Several cylindrical samples made by different compounds were tested within a period of about 112 days. Requirements with respect to strength were met within a few days. Demands on the eluate-criteria need additional investigations. (orig.)

Determination of Food Oxalates Using Silica–Titania Xerogel Modified with Eriochrome Cyanine R

Directory of Open Access Journals (Sweden)

Maria A. Morosanova

2018-03-01

Full Text Available The interaction of silica–titania xerogel with triphenylmethane dyes (pyrocatechol violet, chrome azurol S, eriochrome cyanine R has been investigated to create a new sensor material for solid phase spectrophotometric determination of food oxalates. The complex forming reaction between xerogel incorporated titanium(IV and triphenylmethane dyes has been studied; half-reaction periods, complex composition, equilibrium constants, and xerogel sorption capacity have been calculated for each dye. Eriochrome cyanine R (ECR is characterized by the shortest half-reaction period, the smallest equilibrium constant, and the greatest capacity; it has been chosen for the sensor material construction because titanium(IV-ECR complex is formed faster and can be destroyed easier than other studied complexes. The interaction of this sensor material with oxalates has been described: the presence of oxalates causes sensor material discoloration and the absorbance is used as analytical signal. The analytical range is 35–900 mg/L (LOD 10.5 mg/L, n = 7. High concentrations of interfering inorganic anions, organic acids, and sucrose did not affect oxalate determination. Proposed solid phase spectrophotometric procedure has been successfully applied for the determination of oxalates in food samples (sorrel, spinach, parsley, ginger, and black pepper and the results are in good agreement with HPLC oxalate determination.

Thermomechanical and Photophysical Properties of Crystal-Violet-Dye/H2O Based Dissolutions via the Pulsed Laser Photoacoustic Technique

Directory of Open Access Journals (Sweden)

Vicente Torres-Zúñiga

2014-01-01

Full Text Available Different thermoelastic parameters, for example, the acoustic attenuation and the speed of sound, are fundamental for instrumental calibration and quantitative characterization of organic-based dissolutions. In this work, these parameters as functions of the concentration of an organic dye (crystal-violet: CV in distillated water (H2O based dissolutions are investigated. The speed of sound was measured by the pulsed-laser photoacoustic technique (PLPA, which consists in the generation of acoustic-waves by the optical absorption of pulsed light in a given material (in this case a liquid sample. The thermally generated sound-waves traveling through a fluid are detected with two piezoelectric sensors separated by a known distance. An appropriate processing of the photoacoustic signals allows an adequate data analysis of the generated waves within the system, providing an accurate determination of the speed of sound as function of the dye-concentration. The acoustic attenuation was calculated based on the distance of the two PZT-microphones to an acoustic-source point and performing linear-fitting of the experimental data (RMS-amplitudes as function of the dye-concentration. An important advantage of the PLPA-method is that it can be implemented with poor or null optical transmitting materials permitting the characterization of the mechanical and concentration/aggregate properties of dissolved organic compounds.

Chromitites of the Akkarginskiy massif (the Southern Urals

Directory of Open Access Journals (Sweden)

D. E. Saveliev

2018-03-01

Full Text Available We consider the geological features of ultramafic rock and chrome ore deposits. It is shown that all studied deposits are podiform in morphology that is typical for the ophiolite ultramafic rocks. Morphological and chemical features of the accessory and oreforming spinels are described. Accessory chrome spinels from ultramafic rocks are middle-Cr and high-Cr in chemistry (>42% Cr2O3. All studied ore-forming chrome spinels from deposits in the Main Ore Zone are high-Cr (54–63% Cr2O3. Some middle-Cr oreforming spinels were found in deposit of the East Ore Zone (48% Cr2O3. We adduce a proof of the tectonic origin of present-day structure of the Akkarginskiy massif and its chrome ore deposits.

Perilaku Krom Dalam Limbah Cair Penyamakan Kombinasi Krom-Gambir dan Krom-Mimosa Pada Penyamakan Kulit

Directory of Open Access Journals (Sweden)

Ardinal Ardinal

2014-06-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE This study aims to determine the amount of chrome that come out together with tannery waste in a tanned combination process of chrome-gambier and chrome-mimosa. the process research performed by 2 stages. The 1st stage  using chrome with 5 concentration,    they were 2,4,6 and 8 %. Then it followed by the 2nd stage  tanning process by using vegetable tanning, gambier and mimosa, with each 7% and 9% concentration. The results showed that the combination of chrome-gambier tanned at the same concentration disposed chromium waste less than the combination of chrome-mimosa tanned. The lowest total chrome waste on the chrome-gambier tanning combination was 3.9 ppm at  2% chromium and 7% gambier concentration and the highest was 146.6 ppm at 8% chromium and 9% gambier concentrations.  The lowest total chrome waste on the combination of chrome-mimosa tanning was 2.2 ppm at  2% chromium and 7% mimosa concentration and the highest was 170.4 ppm at 8 % chromium and 9% mimosa concentration. The 2ndtanning, was combination tanning process, chrome-gambier able to reduce chromium levels more than the chrome-mimosa tanning.ABSTRAKPenelitian ini bertujuan untuk mengetahui jumlah krom yang ikut terbuang bersama limbah proses penyamakan kulit yang di samak kombinasi krom-gambir dan krom-mimosa. Pelaksanaan penelitian proses penyamakan kulit  dilakukan dengan 2 tahap. Tahap I menggunakan krom dengan 5 variasi  konsentrasi yaitu 2, 4, 6 dan 8%. Setelah penyamakan tahap I kemudian dilanjutkan penyamakan tahap II dengan menggunakan penyamakan nabati, gambir dan mimosa, dengan variasi konsentrasi masing-masing 7 dan 9%. Hasil penelitian menunjukkan bahwa perlakuan penyamakan kombinasi krom-gambir pada konsentrasi yang sama menghasilkan limbah krom yang lebih sedikit dibandingkan dengan samak kombinasi krom-mimosa. Jumlah limbah krom pada penyamak kombinasi krom-gambir terendah adalah 3,9 ppm pada konsentrasi krom

Physicochemical modeling of reactive violet 5 dye adsorption on home-made cocoa shell and commercial activated carbons using the statistical physics theory

Directory of Open Access Journals (Sweden)

Lotfi Sellaoui

Full Text Available Two equilibrium models based on statistical physics, i.e., monolayer model with single energy and multilayer model with saturation, were developed and employed to access the steric and energetic aspects in the adsorption of reactive violet 5 dye (RV-5 on cocoa shell activated carbon (AC and commercial activated carbon (CAC, at different temperatures (from 298 to 323 K. The results showed that the multilayer model with saturation was able to represent the adsorption system. This model assumes that the adsorption occurs by a formation of certain number of layers. The n values ranged from 1.10 to 2.98, indicating that the adsorbate molecules interacted in an inclined position on the adsorbent surface and aggregate in solution. The study of the total number of the formed layers (1 + L2 showed that the steric hindrance is the dominant factor. The description of the adsorbate–adsorbent interactions by calculation of the adsorption energy indicated that the process occurred by physisorption in nature, since the values were lower than 40 kJ mol−1. Keywords: RV-5 dye, Activated carbon, Modeling, Aggregation

40 CFR 425.50 - Applicability; description of the no beamhouse subcategory.

Science.gov (United States)

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY No... cattle hides, sheepskins, or splits (hair previously removed and pickled) into finished leather by chrome or non-chrome tanning, and retan-wet finishing. ...

Blue light induced free radicals from riboflavin in degradation of crystal violet by microbial viability evaluation.

Science.gov (United States)

Liang, Ji-Yuan; Yuann, Jeu-Ming P; Hsie, Zong-Jhe; Huang, Shiuh-Tsuen; Chen, Chiing-Chang

2017-09-01

Crystal violet (CV) is applied in daily use mainly as a commercial dye and antimicrobial agent. Waste water containing CV may affect aquatic ecosystems. Riboflavin, also known as vitamin B 2 , is non-toxic and an essential vitamin required for the functions of the human body. Riboflavin is photosensitive to UV and visible light in terms of generating reactive oxygen species. This study investigated the potential application of blue light on riboflavin, so as to come up with an effective way of degrading CV during its treatment. Photosensitivity of CV leading to degradation in the presence of riboflavin was investigated by light intensity, exposure time, and irradiation dosage. The degradation of CV during riboflavin photolysis treatment was studied by a UV/vis spectrometry and chromatography. The effects of CV degradation on microbial viability are relevant when considering the influences on the ecosystem. This study proved that riboflavin photochemical treatment with blue light degrades CV dye by ROS formation. The riboflavin photolysis-treated CV solution appeared to be transparent during conformational transformations of the CV that was rearranged by free radical species generated from riboflavin photolysis. After riboflavin photolysis, colony-forming units (CFUs) were determined for each CV solution. CFU preservation was 85.2% for the CV dissolved riboflavin solution treated with blue light irradiation at 2.0mW/cm 2 for 120min. Degradation of CV by riboflavin photochemical procedures can greatly reduce antimicrobial ability and serve as an environmental friendly waste water treatment method. Our results presented here concerning riboflavin photolysis in degradation of CV provide a novel technique, and a simple and safe practice for environmental decontamination processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Electrochemical corrosion measurements on noble electrodeposits

DEFF Research Database (Denmark)

Christoffersen, Lasse; Maahn, Ernst Emanuel

1998-01-01

Novel electrodeposits are compared with hard chrome and electroless Ni-P with respect to production, corrosion resistance and hardness.......Novel electrodeposits are compared with hard chrome and electroless Ni-P with respect to production, corrosion resistance and hardness....

Pengaruh penggunaan pankreas sapi dan dua jenis bahan penyamak terhadap kualitas fisik kulit skrotum kambing

Directory of Open Access Journals (Sweden)

Titik Purwati Widowati

2003-06-01

Full Text Available Abstract The pancreas of cow was applied as bating agent for wet-salted scrotum skins of goat. The bated skins were then applied with vetetable tanning, chrome-agent and the combination of both agents. The tanned skins were analyzed their tensile strength and elasticity. The results showed that there were significant differencis on those parameters. The tensile strength and elasticity of chrome tanned, vegetable tanned, and the combination of chrome and vegetable tanned-skins were 107,75 kg/cm2 and 100,5%; 56,83 kg/cm2 and 27,83 %; and 52,28 kg/cm2 and 55,67% respectively. The tensile strength and elasticity of tanned skins indicated a tendency to increase when the concentration of cow pancreas was increased up to 1.5 % and decreased when the concentration reaches 2 % for chrome tanned skins.

Removal of heavy metals from metal-containing effluent by yeast ...

African Journals Online (AJOL)

Removal of heavy metals from metal-containing effluent by yeast biomass. ... Research studies have described this phenomenon of fast initial sorption with a ... chrome and tin from the chrome and tin effluents of a local iron and steel industry.

New technologies to enhance quality and safety of table eggs: ultra-violet treatment and modified atmosphere packaging

Directory of Open Access Journals (Sweden)

Frédérique Pasquali

2014-12-01

Full Text Available In the present study the effect of ultra-violet (UV treatment alone and in combination with 100% CO2 modified atmosphere packaging (MAP was evaluated both on the survival of naturally occurring bacteria, as well as on quality parameters of table eggs during 28 days of storage at 21°C. Table eggs were collected from the conveyor belt after the UV module, and placed on carton trays. A representative number of carton trays were packed in a high barrier multilayer pouch filled with 100% CO2. All eggs were stored at 21°C and analysed at 0, 1, 7, 14, 21 and 28 days of storage. Eggs not treated with UV and not packed were also included. On the eggshells total colony count, total coliforms and faecal coliforms counts, as well as the detection of Salmonella spp. were investigated. Moreover, chemical-functional parameters such as weight loss, albumen pH and Haugh Unit (HU were evaluated. The total colony count on UV treated table eggs was approximately 1 log10 CFU/g lower than untreated eggs (2.27 vs 3.29 log10 CFU/g. During storage, CO2 packed eggs maintained the initial values of HU, whereas the albumen pH decreased up to 1.5-2 points in comparison to unpacked eggs. The UV treatment was effective in reducing the total colony count on the surface of table eggs. MAP showed a great potential in maintaining/enhance the technological properties of egg constituents (higher foam stability of the albumen for meringue preparation without significantly impacting on the microbial load of table eggs.

Physicochemcial characteristic of CdS-anchored porous WS2 hybrid in the photocatalytic degradation of crystal violet under UV and visible light irradiation

Science.gov (United States)

Vattikuti, S. V. Prabhakar; Ngo, Ich-Long; Byon, Chan

2016-11-01

In this work, we report the synthesis of CdS-incorporated porous WS2 by a simple hydrothermal method. The structural, morphological, and optical properties of the samples were examined by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Fourier transform infrared spectroscopy (FTIR), high resolution X-ray photoelectron spectroscopy (XPS) and UV-visible spectrometry. The photocatalytic activities were established for degradation of crystal violet (CV) under UV and visible light irradiation. The CdS-incorporated porous WS2 hybrid demonstrated high photocatalytic activity for degradation of CV pollutant compared to pure CdS nanoparticles and porous WS2 sheets. This result implies that the CdS-incorporated porous WS2 promoted more electron-hole pair transformation under UV and visible light irradiation. This significant enhancement of photocatalytic efficiency of CdS-incorporated porous WS2 photocatalyst under visible light can be ascribed to the presence of CdS nanospheres on the meshed-like WS2 sheets which potentially improves absorption in the visible range enabled by surface plasmon resonance effect of CdS nanospheres. The photostability and reusability of the CdS-porous WS2 were examined through recycling experiments.

Ultraviolet Curable Powder Coatings with Robotic Curing for Aerospace Applications

Science.gov (United States)

2012-05-01

millions of dollars annually on solvent- based coatings  Hexavalent chrome primer use still very widespread  Contains or requires volatile solvent...functionality can be added  Various advanced non- chrome corrosion inhibitors DISTRIBUTION A. Approved for public release; distribution unlimited. Case

40 CFR 415.344 - Pretreatment standards for existing sources (PSES).

Science.gov (United States)

2010-07-01

... Pigments Production Subcategory § 415.344 Pretreatment standards for existing sources (PSES). (a) Existing... chrome pigments process wastewater into a publicly owned treatment works are subject only to the... standards for existing sources (PSES): Subpart AH—Chrome Pigments Pollutant or pollutant property PSES...

Fine and hyperfine structure spectra of the ultra-violet 23S → 53P transition in 4He and 3He with a frequency doubled CW ring laser, detected via associative ionization

International Nuclear Information System (INIS)

Runge, S.; Pesnelle, A.; Perdrix, M.; Sevin, D.; Wolffer, N.; Watel, G.

1982-01-01

High resolution laser spectroscopy coupled to a sensitive method of detection via mass analysis of He + 2 ions produced in He(5 3 P) + He(1 1 S) collisions, is used to obtain the fine and hyperfine spectra of the ultra-violet He 2 3 S → 5 3 P transition. A cw tunable UV radiation around 294.5 nm is generated by intracavity frequency doubling a Rhodamine 6G single mode ring dye laser using an ADA crystal. Both spectra enable fine and hyperfine structures to be determined within a few MHz. The magnetic dipole coupling constant A of the 5 3 P term of 3 He is found to be -4326 +- 9 MHz (-0.1443 +- 0.0003 cm -1 ). (orig.)

Elemental composition of airborne dust in the shale shaker house during an offshore drilling operation

DEFF Research Database (Denmark)

Hansen, A.B.; Larsen, E.; Hansen, L.V.

1991-01-01

chrome lignosulphonate and chrome lignite, was circulated between the borehole and the Shale Shaker House. The concentration of airborne dust in the atmosphere was determined and the elemental composition of the particles analysed by both PIXE (proton-induced X-ray emission) and ICP-MS (inductively...

Using of Hyperbranched Poly(amidoamine as Pretanning Agent for Leather

Directory of Open Access Journals (Sweden)

Amal Amin Ibrahim

2013-01-01

Full Text Available Although chrome is considered as the major tanning agent in the production of all types of hides and leather worldwide, it represents a serious source of environmental pollution. Therefore, polyamidoamine hyperbranched polymer (HPAM was involved in pretanning of the depickled hides to enhance the chromium uptake during the tanning process. The key parameters which affect the exhaustion and fixation of chrome tan including shrinkage temperature of the tanned leather were studied. The results showed a significant improvement in the chrome exhaustion, the shrinkage temperature, and the texture and softness of the leather treated by HPAM.

Fabrication of SnO2-Reduced Graphite Oxide Monolayer-Ordered Porous Film Gas Sensor with Tunable Sensitivity through Ultra-Violet Light Irradiation

Science.gov (United States)

Xu, Shipu; Sun, Fengqiang; Yang, Shumin; Pan, Zizhao; Long, Jinfeng; Gu, Fenglong

2015-01-01

A new graphene-based composite structure, monolayer-ordered macroporous film composed of a layer of orderly arranged macropores, was reported. As an example, SnO2-reduced graphite oxide monolayer-ordered macroporous film was fabricated on a ceramic tube substrate under the irradiation of ultra-violet light (UV), by taking the latex microsphere two-dimensional colloid crystal as a template. Graphite oxide sheets dispersed in SnSO4 aqueous solution exhibited excellent affinity with template microspheres and were in situ incorporated into the pore walls during UV-induced growth of SnO2. The growing and the as-formed SnO2, just like other photocatalytic semiconductor, could be excited to produce electrons and holes under UV irradiation. Electrons reduced GO and holes adsorbed corresponding negative ions, which changed the properties of the composite film. This film was directly used as gas-sensor and was able to display high sensitivity in detecting ethanol gas. More interestingly, on the basis of SnO2-induced photochemical behaviours, this sensor demonstrated tunable sensitivity when UV irradiation time was controlled during the fabrication process and post in water, respectively. This study provides efficient ways of conducting the in situ fabrication of a semiconductor-reduced graphite oxide film device with uniform surface structure and controllable properties. PMID:25758292

Determining the degradation efficiency and mechanisms of ethyl violet using HPLC-PDA-ESI-MS and GC-MS

Directory of Open Access Journals (Sweden)

Chung Wen-Hsin

2012-06-01

Full Text Available Abstract Background The discharge of wastewater that contains high concentrations of reactive dyes is a well-known problem associated with dyestuff activities. In recent years, semiconductor photocatalysis has become more and more attractive and important since it has a great potential to contribute to such environmental problems. One of the most important aspects of environmental photocatalysis is in the selection of semiconductor materials like ZnO and TiO2, which are close to being two of the ideal photocatalysts in several respects. For example, they are relatively inexpensive, and they provide photo-generated holes with high oxidizing power due to their wide band gap energy. In this work, nanostructural ZnO film on the Zn foil of the Alkaline-Manganese Dioxide-Zinc Cell was fabricated to degrade EV dye. The major innovation of this paper is to obtain the degradation mechanism of ethyl violet dyes resulting from the HPLC-PDA-ESI-MS analyses. Results The fabrication of ZnO nanostructures on zinc foils with a simple solution-based corrosion strategy and the synthesis, characterization, application, and implication of Zn would be reported in this study. Other objectives of this research are to identify the reaction intermediates and to understand the detailed degradation mechanism of EV dye, as model compound of triphenylmethane dye, with active Zn metal, by HPLC-ESI-MS and GC-MS. Conclusions ZnO nanostructure/Zn-foils had an excellent potential for future applications on the photocatalytic degradation of the organic dye in the environmental remediation. The intermediates of the degradation process were separated and characterized by the HPLC-PDA-ESI-MS and GC-MS, and twenty-six intermediates were characterized in this study. Based on the variation of the amount of intermediates, possible degradation pathways for the decolorization of dyes are also proposed and discussed.

SERS active Ag encapsulated Fe@SiO2 nanorods in electromagnetic wave absorption and crystal violet detection.

Science.gov (United States)

Senapati, Samarpita; Srivastava, Suneel Kumar; Singh, Shiv Brat; Kulkarni, Ajit R

2014-11-01

The present work is focused on the preparation of Fe nanorods by the chemical reduction of FeCl3 (aq) using NaBH4 in the presence of glycerol as template followed by annealing of the product at 500°C in the presence of H2 gas flow. Subsequently, its surface has been modified by silica followed by silver nanoparticles to form silica coated Fe (Fe@SiO2) and Ag encapsulated Fe@SiO2 nanostructure employing the Stöber method and silver mirror reaction respectively. XRD pattern of the products confirmed the formation of bcc phase of iron and fcc phase of silver, though silica remained amorphous. FESEM images established the growth of iron nanorods from the annealed product and also formation of silica and silver coating on its surface. The appearance of the characteristics bands in FTIR confirmed the presence of SiO2 on the Fe surface. Magnetic measurements at room temperature indicated the ferromagnetic behavior of as prepared iron nanorods, Fe@SiO2 and silver encapsulated Fe@SiO2 nanostructures. All the samples exhibited strong microwave absorption property in the high frequency range (10GHz), though it is superior for Ag encapsulated Fe@SiO2 (-14.7dB) compared with Fe@SiO2 (-9.7dB) nanostructures of the same thickness. The synthesized Ag encapsulated Fe@SiO2 nanostructure also exhibited the SERS phenomena, which is useful in the detection of the carcinogenic dye crystal violet (CV) upto the concentration of 10(-10)M. All these findings clearly demonstrate that the Ag encapsulated Fe@SiO2 nanostructure could efficiently be used in the environmental remediation. Copyright © 2014 Elsevier Inc. All rights reserved.

Preparation of Calcined Zirconia-Carbon Composite from Metal Organic Frameworks and Its Application to Adsorption of Crystal Violet and Salicylic Acid

Directory of Open Access Journals (Sweden)

Zubair Hasan

2016-03-01

Full Text Available Zirconia-carbon (ZC composites were prepared via calcination of Zr-based metal organic frameworks, UiO-66 and amino-functionalized UiO-66, under N2 atmosphere. The prepared composites were characterized using a series of instrumental analyses. The surface area of the ZC composites increased with the increase of calcination temperature, with the formation of a graphite oxide phase observed at 900 °C. The composites were used for adsorptive removal of a dye (crystal violet, CV and a pharmaceutical and personal care product (salicylic acid, SA. The increase of the calcination temperature resulted in enhanced adsorption capability of the composites toward CV. The composite calcined at 900 °C exhibited a maximum uptake of 243 mg·g−1, which was much greater than that by a commercial activated carbon. The composite was also effective in SA adsorption (102 mg·g−1, and N-functionalization of the composite further enhanced its adsorption capability (109 mg·g−1. CV adsorption was weakly influenced by solution pH, but was more dependent on the surface area and pore volume of the ZC composite. Meanwhile, SA adsorption showed strong pH dependence, which implies an active role of electrostatic interactions in the adsorption process. Base-base repulsion and hydrogen bonding are also suggested to influence the adsorption of CV and SA, especially for the N-functionalized composite.

77 FR 60285 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-10-03

... the MLG for chicken- wire cracks, corrosion, and chrome plate distress; repetitive magnetic particle..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65... magnetic particle inspections of the outer diameter chrome on the center axles of the MLG for cracks; and...

Heavy Metal Contamination of Popular Nail Polishes in Iran

Directory of Open Access Journals (Sweden)

Golnaz Karimi

2015-06-01

Full Text Available Background: Toxic and hazardous heavy metals like arsenic, lead, mercury, zinc, chromium and iron are found in a variety of personal care products, e.g. lipstick, whitening toothpaste, eyeliner and nail color. The nails absorb the pigments of nail polishes and vaporized or soluble metals can easily pass it. The goal of this survey was to assess whether the different colors of nail polishes comply with maximum concentrations of heavy metals in the EPA’s guidelines. Methods: 150 samples of different popular brands of nail polishes in 13 colors (yellow, beige, silver, pink, white, violet, brown, golden, green, black, colorless, red and blue were randomly purchased from beauty shops in Tehran City, Iran, in 2014. Microwave digestion EPA method 3051 was used by a microwave oven to determine the amount of 5 heavy metals; Nickel, Chromium, Lead, Arsenic and Cadmium. One-way ANOVA, Two-way ANOVA, hierarchical cluster, and principal component analyses were applied by Statistica 7.0 software. Results: The concentrations of chrome, lead, nickel and arsenic showed significant differences between the colors (p<0.05. In all studied samples, the level of cadmium was beyond the safe maximum permissible limit (MPS, but no significance difference in the cadmium content was identified. Conclusion: Due to the high concentrations of toxic metals in many brands of nail polishes, meticulous quality control is recommended for these beauty products.

7 CFR 1728.202 - RUS Bulletin 1728H-702, RUS Specification for Quality Control and Inspection of Timber Products.

Science.gov (United States)

2010-01-01

... vacuum during each cycle of treatment. They shall also be equipped with indicating thermometers and... shall be determined in accordance with AWPA Standard A3. Chrome Azurol S and Penta-Check shall be used.... Chrome Azurol S and Penta-Check shall be used to determine penetration of copper containing preservatives...

Enhancing the Antibacterial Activity of Light-Activated Surfaces Containing Crystal Violet and ZnO Nanoparticles: Investigation of Nanoparticle Size, Capping Ligand, and Dopants.

Science.gov (United States)

Sehmi, Sandeep K; Noimark, Sacha; Pike, Sebastian D; Bear, Joseph C; Peveler, William J; Williams, Charlotte K; Shaffer, Milo S P; Allan, Elaine; Parkin, Ivan P; MacRobert, Alexander J

2016-09-30

Healthcare-associated infections pose a serious risk for patients, staff, and visitors and are a severe burden on the National Health Service, costing at least £1 billion annually. Antimicrobial surfaces significantly contribute toward reducing the incidence of infections as they prevent bacterial adhesion and cause bacterial cell death. Using a simple, easily upscalable swell-encapsulation-shrink method, novel antimicrobial surfaces have been developed by incorporating metal oxide nanoparticles (NPs) and crystal violet (CV) dye into medical-grade polyurethane sheets. This study compares the bactericidal effects of polyurethane incorporating ZnO, Mg-doped ZnO, and MgO. All metal oxide NPs are well defined, with average diameters ranging from 2 to 18 nm. These materials demonstrate potent bactericidal activity when tested against clinically relevant bacteria such as Escherichia coli and Staphylococcus aureus . Additionally, these composites are tested against an epidemic strain of methicillin-resistant Staphylococcus aureus (MRSA) that is rife in hospitals throughout the UK. Furthermore, we have tested these materials using a low light intensity (∼500 lx), similar to that present in many clinical environments. The highest activity is achieved from polymer composites incorporating CV and ∼3 nm ZnO NPs, and the different performances of the metal oxides have been discussed.

Phytoextraction potential of water fern (Azolla pinnata) in the removal of a hazardous dye, methyl violet 2B: Artificial neural network modelling.

Science.gov (United States)

Kooh, Muhammad Raziq Rahimi; Lim, Linda B L; Lim, Lee-Hoon; Malik, Owais Ahmed

2018-04-16

This study investigated the potential of Azolla pinnata (AP) in the removal of toxic methyl violet 2B (MV) dye wastewater using the phytoextraction approach with the inclusion of an Artificial Neural Network (ANN) modelling. Parameters examined included the effects of dye concentration, pH and plant dosage. The highest removal efficiency was 93% which was achieved at a plant dosage of 0.8 g (dye volume = 200 mL, initial pH = 6.0, initial dye concentration = 10 mg L -1 ). A significant decrease in relative frond number (RFN), a growth rate estimator, observed at a dye concentration of 20 mg L -1 MV indicated some toxicity, which coincided with the plant pigments studies where the chlorophyll a content was lower than the control. There were little differences in the plant pigment contents between the control and those in the presence of dye (5 to 15 mg L -1 ) indicating the tolerance of AP to MV at lower concentrations. A three-layer ANN model was optimized (6 neurons in the hidden layer) and successfully predicted the phytoextraction of MV (R = 0.9989, RMSE = 0.0098). In conclusion, AP proved to be a suitable plant that could be used for the phytoextraction of MV while the ANN modelling has shown to be a reliable method for the modelling of phytoextraction of MV using AP.

Fabrication of CMC-g-PAM superporous polymer monoliths via eco-friendly Pickering-MIPEs for superior adsorption of methyl violet and methylene blue

Science.gov (United States)

Wang, Feng; Zhu, Yongfeng; Wang, Wenbo; Zong, Li; Lu, Taotao; Wang, Aiqin

2017-06-01

A series of superporous carboxymethylcellulose-graft-poly(acrylamide) (CMC-g-PAM) polymer monoliths presenting interconnected pore structure and excellent adsorption properties were prepared by one-step free-radical grafting polymerization reaction of CMC and acrylamide (AM) in the oil-in-water (O/W) Pickering-medium internal phase emulsions (Pickering-MIPEs) composed of non-toxic edible oil as a dispersion phase and natural Pal nanorods as stabilizers. The effects of Pal dosage, AM dosage, and co-surfactant Tween-20 (T-20) on the pore structures of the monoliths were studied. It was revealed that the well-defined pores were formed when the dosages of Pal and T-20 are 9-14% and 3%, respectively. The porous monolith can rapidly adsorb 1585 mg/g of methyl violet (MV) and 1625 mg/g of methylene blue (MB). After the monolith was regenerated by adsorption-desorption process for 5 times, the adsorption capacities still reached 92.1% (for MV) and 93.5% (for MB) of the initial maximum adsorption capacities. The adsorption process was fitted with Langmuir adsorption isotherm model and pseudo-second-order adsorption kinetic model very well, which indicate that mono-layer chemical adsorption mainly contribute to the high-capacity adsorption for dyes. The superporous polymer monolith prepared from eco-friendly Pickering-MIPEs shows good adsorption capacity and fast adsorption rate, which is potential adsorbent for the decontimination of dye-containing wastewater.

Polypyrrole-magnetite dispersive micro-solid-phase extraction combined with ultraviolet-visible spectrophotometry for the determination of rhodamine 6G and crystal violet in textile wastewater.

Science.gov (United States)

Kamaruddin, Amirah Farhan; Sanagi, Mohd Marsin; Wan Ibrahim, Wan Aini; Md Shukri, Dyia S; Abdul Keyon, Aemi S

2017-11-01

Polypyrrole-magnetite dispersive micro-solid-phase extraction method combined with ultraviolet-visible spectrophotometry was developed for the determination of selected cationic dyes in textile wastewater. Polypyrrole-magnetite was used as adsorbent due to its thermal stability, magnetic properties, and ability to adsorb Rhodamine 6G and crystal violet. Dispersive micro-solid-phase extraction parameters were optimized, including sample pH, adsorbent amount, extraction time, and desorption solvent. The optimum polypyrrole-magnetite dispersive micro-solid phase-extraction conditions were sample pH 8, 60 mg polypyrrole-magnetite adsorbent, 5 min of extraction time, and acetonitrile as the desorption solvent. Under the optimized conditions, the polypyrrole-magnetite dispersive micro-solid-phase extraction with ultraviolet-visible method showed good linearity in the range of 0.05-7 mg/L (R 2  > 0.9980). The method also showed a good limit of detection for the dyes (0.05 mg/L) and good analyte recoveries (97.4-111.3%) with relative standard deviations extraction and determination of dyes at trace concentration levels. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cellular attachment and spatial control of cells using micro-patterned ultra-violet/ozone treatment in serum enriched media.

Science.gov (United States)

Mitchell, S A; Poulsson, A H C; Davidson, M R; Emmison, N; Shard, A G; Bradley, R H

2004-08-01

Ultra-violet Ozone (UVO) modified polystyrene (PS) surfaces were analyzed by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), contact angle (CA), optical microscopy (OM) and cell culture experiments. UV/Ozone treatment up to 900 s was used to increase the surface oxygen concentration of PS surfaces from 0% to approximately 35% (unwashed) and 0% to approximately 27% (washed). The observed differences in oxygen concentration, between washed and unwashed surfaces, have been previously attributed to the removal of low molecular weight debris produced in this treatment process. Surface roughness (Rq) is known to affect cellular attachment and proliferation. AFM studies of the UV/Ozone treated PS surfaces show the surface roughness is an order of magnitude less than that expected to cause an effect. UV/Ozone treatment of PS showed a marked change in CA which decreased to approximately 60 degrees after 900 s treatment. The increased attachment and proliferation of Chinese hamster ovarian (CHO) and mouse embryo 3T3-L1 (3T3) cells on the treated surfaces compared to untreated PS were found to correlate strongly with the increase in surface oxygen concentration. Surface chemical oxidation patterns on the PS were produced using a simple masking technique and a short UV/Ozone treatment time, typically 20-45 s. The chemical patterns on PS were visualized by water condensation and the spatially selective attachment of CHO and 3T3-L1 cells cultured with 10% (v/v) serum. This paper describes an easily reproducible, one step technique to produce a well-defined, chemically heterogeneous surface with a cellular resolution using UV/Ozone modification. By using a variety of cell types, that require different media conditions, we have been able to expand the potential applications of this procedure.

76 FR 426 - Airworthiness Directives; The Boeing Company Model 737-300, -400, and -500 Series Airplanes

Science.gov (United States)

2011-01-05

... corrosion damage of the chrome runout on the head side found on all four midspar fuse pins of the nacelle strut. Additionally, a large portion of the chrome plate was missing from the corroded area of the shank... 616 $209,440, per inspection inspections (required by AD inspection cycle. 2008-21-03). cycle. Midspar...

Analysis of Sulfidation Routes for Processing Weathered Ilmenite Concentrates Containing Impurities

Science.gov (United States)

Ahmad, Sazzad; Rhamdhani, M. Akbar; Pownceby, Mark I.; Bruckard, Warren J.

Rutile is the preferred feedstock for producing high-grade TiO2 pigment but due to decreasing resources, alternative materials such as ilmenite is now used to produce a synthetic rutile (SR) feedstock. This requires removal of impurities (e.g. Fe, Mg, Mn) which, for a primary ilmenite is straightforward process. Processing of weathered ilmenite however, is complex, especially when chrome-bearing impurities are present since minor chromium downgrades the SR market value as it imparts color to the final TiO2 pigment, Chrome-bearing spinels are a problem in weathered ilmenites from the Murray Basin, Australia as their physical and chemical properties overlap with ilmenite making separation difficult. In this paper, different sulfidation process routes for weathered ilmenites are analyzed for their applicability to Murray Basin deposits as a mean of remove chrome spinel impurities. Thermodynamic and experimental studies indicated that selective sulfidation of chrome-bearing spinel can be achieved under controlled pO2 and pS2 processing conditions thereby making them amenable to separation.

Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

Directory of Open Access Journals (Sweden)

Jie Zong

2016-01-01

Full Text Available Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The results showed that the percentage of reduction of TOC in the tannery waste chrome liquor by method of Fenton oxidation, acid enzyme, and the flocculant was 71.15%, 65.26%, and 22.05%, respectively. Therefore, the organism content of chrome tanning waste liquid was greatly reduced through the pretreatment. And the application experiment showed that the properties and grain surface and fibers of the tanned leather with commercial chromium powder and chrome tanning agent prepared from the chromium waste liquid treated with Fenton are nearly the same.

Controlled hydrothermal synthesis of BiOxCly/BiOmIn composites exhibiting visible-light photocatalytic degradation of crystal violet

International Nuclear Information System (INIS)

Jiang, Yu-Rou; Lin, Ho-Pan; Chung, Wen-Hsin; Dai, Yong-Ming; Lin, Wan-Yu; Chen, Chiing-Chang

2015-01-01

Highlights: • This is the first report on a series of BiO x Cl y /BiO m I n heterojunctions. • The BiO x Cl y /BiO m I n composition was controlled by adjusting the growth parameters. • The BiO x Cl y /BiO m I n were indirect semiconductors with a 1.78–2.95-eV bandgap. • The new photocatalysts removed CV at a much faster rate than TiO 2 . • Mechanisms were determined by separating the intermediates using HPLC-MS. - Abstract: A series of BiO x Cl y /BiO m I n composites were prepared using autoclave hydrothermal methods. The composition and morphologies of the BiO x Cl y /BiO m I n composites were controlled by adjusting the experimental conditions: the reaction pH value, temperature, and KCl/KI molar ratio. The products were characterized using X-ray diffraction, scanning electron microscopy-electron dispersive X-ray spectroscopy, UV–vis diffuse reflectance spectroscopy, Brunauer–Emmett–Teller specific surface areas, cathodoluminescence, high-resolution transmission electron microscopy, and high-resolution X-ray photoelectron spectroscopy. The photocatalytic efficiencies of composite powder suspensions were evaluated by monitoring the crystal violet (CV) concentrations. In addition, the quenching effects of various scavengers indicated that the reactive O 2 · − played a major role, and OH· or h + played a minor role in CV degradation. The intermediates formed during the decomposition process were isolated, identified, and characterized using high performance liquid chromatography-photodiode array-electrospray ionization-mass spectrometry to elucidate the CV decomposition mechanism

Binary system containing the pulsar PSR 1913 + 16 and ultra-violet and x-radiation from accreting magnetic white dwarfs

International Nuclear Information System (INIS)

Masters, A.R.

1978-01-01

Part I of the thesis deals with the binary system containing the pulsar PSR 1913 + 16. The system has been touted as a laboratory for testing relativistic theories of gravity, and is also a challenge for theories of stellar evolution. However, proposed uses of the system rely on assumptions about the nature of the pulsar's unobserved companion. Ways of determining the nature of the companion from observation of the pulsar are discussed. Geometrical constraints on the size of the pulsar's orbit and the observed slow rate of the orbit's precession require that the companion be a black hole, a neutron star, a white dwarf or a helium main-sequence star. Observable second-order relativistic effects may or may not further restrict the list of candidates. The discussion summarizes Masters and Roberts, 1975 Ap.J. (Letters), 195, L107, and Roberts, Masters and Arnett, 1976, Ap. J., 203, 196. Part II of the thesis treats ultra-violet and X-radiation from accreting magnetic white dwarfs. Matter from a companion star falling onto a white dwarf is shock-heated near the stellar surface and radiatively cooled. The post-shock region is approximated by a uniform, geometrically thin slab and determine the physical conditions behind the shock and the emitted spectrum for a range of stellar masses, magnetic fields and accretion rates. At low magnetic fields and high accretion rates, bremsstrahlung is the dominant cooling mechanism and the post-shock material is a single fluid (the electrons and ions have a common temperature). As the magnetic field increases or the accretion rate decreases, cyclotron emission becomes more important than bremsstrahlung

Vapor pressure and evaporation rate of certain heat-resistant compounds in a vacuum at high temperatures

Science.gov (United States)

Bolgar, A. S.; Verkhoglyadova, T. S.; Samsonov, G. V.

1985-01-01

The vapor pressure and evaporation rate of borides of titanium, zirconium, and chrome; and of strontium and carbides of titanium, zirconium, and chrome, molybdenum silicide; and nitrides of titanium, niobium, and tantalum in a vacuum were studied. It is concluded that all subject compounds evaporate by molecular structures except AlB sub 12' which dissociates, losing the aluminum.

Effects of as-cast and wrought Cobalt-Chrome-Molybdenum and Titanium-Aluminium-Vanadium alloys on cytokine gene expression and protein secretion in J774A.1 macrophages.

Science.gov (United States)

Jakobsen, Stig S; Larsen, A; Stoltenberg, M; Bruun, J M; Soballe, K

2007-09-11

Insertion of metal implants is associated with a possible change in the delicate balance between pro- and anti-inflammatory proteins, probably leading to an unfavourable predominantly pro-inflammatory milieu. The most likely cause is an inappropriate activation of macrophages in close relation to the metal implant and wear-products. The aim of the present study was to compare surfaces of as-cast and wrought Cobalt-Chrome-Molybdenum (CoCrMo) alloys and Titanium-Aluminium-Vanadium (TiAlV) alloy when incubated with mouse macrophage J774A.1 cell cultures. Changes in pro- and anti-inflammatory cytokines (TNF-alpha, IL-6, IL-alpha, IL-1beta, IL-10) and proteins known to induce proliferation (M-CSF), chemotaxis (MCP-1) and osteogenesis (TGF-beta, OPG) were determined by ELISA and Real Time reverse transcriptase - PCR (Real Time rt-PCR). Lactate dehydrogenase (LDH) was measured in the medium to asses the cell viability. Surface properties of the discs were characterised with a profilometer and with energy dispersive X-ray spectroscopy. We here report, for the first time, that the prosthetic material surface (non-phagocytable) of as-cast high carbon CoCrMo reduces the pro-inflammatory cytokine IL-6 transcription, the chemokine MCP-1 secretion, and M-CSF secretion by 77%, 36%, and 62%, respectively. Furthermore, we found that reducing surface roughness did not affect this reduction. The results suggest that as-cast CoCrMo alloy is more inert than wrought CoCrMo and wrought TiAlV alloys and could prove to be a superior implant material generating less inflammation which might result in less osteolysis.

A chemometric-assisted method for the simultaneous determination of malachite green and crystal violet in water based on absorbance-pH data generated by a homemade pH gradient apparatus.

Science.gov (United States)

Yu, Shuling; Yuan, Xuejie; Yang, Jing; Yuan, Jintao; Shi, Jiahua; Wang, Yali; Chen, Yuewen; Gao, Shufang

2015-01-01

An attractive method of generating second-order data was developed by a dropping technique to generate pH gradient simultaneously coupled with diode-array spectrophotometer scanning. A homemade apparatus designed for the pH gradient. The method and the homemade apparatus were used to simultaneously determine malachite green (MG) and crystal violet (CV) in water samples. The absorbance-pH second-order data of MG or CV were obtained from the spectra of MG or CV in a series of pH values of HCl-KCl solution. The second-order data of mixtures containing MG and CV that coexisted with interferents were analyzed using multidimensional partial least-squares with residual bilinearization. The method and homemade apparatus were used to simultaneously determine MG and CV in fish farming water samples and in river ones with satisfactory results. The presented method and the homemade apparatus could serve as an alternative tool to handle some analysis problems. Copyright © 2015 Elsevier B.V. All rights reserved.

The influence of a selenium-chromium-lipid complex obtained from Chlorella vulgaris on the energy metabolism in rats with experimental diabetes

Directory of Open Access Journals (Sweden)

O. Y. Lukashiv

2017-07-01

Full Text Available One of the leading roles in treating diabetes mellitus belongs to chrome ions therapy (III, especially in the complex with selenium (IV. Currently selenium is obtained from unicellular algae, which contain biologically active substances and which are capable of accumulating exogenous microelements. By incubating unicellular algae Chlorella vulgaris Biej. in the conditions of aquaculture with sodium selenite (IV and chromium (III chloride, we obtained a biologically active lipid substance which contains selenium and chromium. The substance was tested for the impact on energy metabolism of animals exposed to experimentally induced diabetes mellitus. The diabetes was caused by modeling obesity of the animals with further injection of streptozotocin in the amount of 65 mg/kg and nicotinamide at the dose of 230 mg/kg. The rats were intragastrically injected with 1 ml of 1% starch solution which contained a selenium-chrome-lipid complex extracted from the Chlorella containing 0.6 µg of selenium, 1.05 µg of chrome and 0.5 mg of lipids for prophylactic, therapeutic and prophylactic-therapeutic purposes; the other group of rats for therapeutic purposes was injected with starch solution with the same composition of microelements in inorganic form – sodium selenite (IV and chromium chloride (III. This paper presents the results of our study of the impact of organic and inorganic compounds of chrome and selenium on the energetic metabolism of rats exposed to experimental diabetes mellitus. The analysis determined that in the rats’ organism, the selenium-chrome-lipid complex from the Chlorella improved the indicators of the energetic metabolism – in the group of rats which received it for therapeutic purposes, we observed an up to 7.5 fold increase in the activity of succinate dehydrogenase compared to the rats which did not receive therapeutic treatment. The increase in the activity of succinate dehydrogenase corresponded to the increase in the

The sequencing of the complete genome of a Tomato black ring virus (TBRV) and of the RNA2 of three Grapevine chrome mosaic virus (GCMV) isolates from grapevine reveals the possible recombinant origin of GCMV.

Science.gov (United States)

Digiaro, M; Yahyaoui, E; Martelli, G P; Elbeaino, T

2015-02-01

The complete genome of a Tomato black ring virus isolate (TBRV-Mirs) (RNA1, 7,366 nt and RNA2, 4,640 nt) and the RNA2 sequences (4,437; 4,445; and 4,442 nts) of three Grapevine chrome mosaic virus isolates (GCMV-H6, -H15, and -H27) were determined. All RNAs contained a single open reading frame encoding polyproteins of 254 kDa (p1) and 149 kDa (p2) for TBRV-Mirs RNA1 and RNA2, respectively, and 146 kDa for GCMV RNA2. p1 of TBRV-Mirs showed the highest identity with TBRV-MJ (94 %), Beet ringspot virus (BRSV, 82 %), and Grapevine Anatolian ringspot virus (GARSV, 66 %), while p2 showed the highest identity with TBRV isolates MJ (89 %) and ED (85 %), followed by BRSV (65 %), GCMV (58 %), and GARSV (57 %). The amino acid identity of RNA2 sequences of four GCMV isolates (three from this study and one from GenBank) ranged from 91 to 98 %, the homing protein being the most variable. The RDP3 program predicted putative intra-species recombination events for GCMV-H6 and recognized GCMV as a putative inter-species recombinant between GARSV and TBRV. In both cases, the recombination events were at the movement protein level.

Low Temperature Powder Coating

Science.gov (United States)

2011-02-09

of volatile organic compounds (VOCs) and hazardous air pollutants (HAPs) • Legacy primers contain hexavalent chrome • Conventional powder coatings...coatings both in laboratory and field service evaluations • LTCPC allows environmental cost reductions through VOC/HAP elimination and hexavalent ... chrome reduction. • The LTCPC process greatly shortens the coating operation (LTCPC cures much more rapidly then conventional wet coatings) resulting in

Environmentally Friendly Zirconium Oxide Pretreatment

Science.gov (United States)

2013-05-01

Society for Testing and Materials AVCRAD Aviation Classification Repair Activity Depot Chrome (VI) Hexavalent Chromium CRS Cold Rolled Steel...are being used commercially in automotive and other industrial operations as replacements to hexavalent chromium-based and zinc phosphate...application over CRS and aluminum with water-borne and solvent-borne Mil-Spec primers gave results in corrosion performance similar to the chrome

Examination of Spray-Applied Oxsilan 9810/2 Steel Pretreatment on a Mine Resistant Ambush Protected (MRAP) Vehicle

Science.gov (United States)

2013-10-01

Coating (CARC) system. The product demonstrated here is Oxsilan 9810/2, manufactured by Chemetall Inc., which satisfies the hexavalent chrome ...system. The product demonstrated here is Oxsilan 9810/2, manufactured by Chemetall Inc., and satisfies the hexavalent chrome prohibition while...2 Omitting this pretreatment/conversion coating step was justified because hexavalent chromium- based pretreatments, such as DOD-P-15328 (8

Synthesis and application of new mordent and disperse azo dyes based on 2,4-dihydroxybenzophenone

Directory of Open Access Journals (Sweden)

BHARAT C. DIXIT

2007-02-01

Full Text Available Novel mordent and disperse azo dyes were prepared by the coupling of various diazo solutions of aromatic amines with 2,4-ihydroxybenzophenone. The resultant dyes were characterized by elemental analyses as well as IR and NMR spectral studies. The UV-visible spectral data have also been iscussed in terms of structural property relationship. The dyeing assessment of all the dyeswas evaluated on wool and polyester textile fibers. The dyeing of chrome treated (i.e., chrome mordented wool and polyesters was also monitored. The results show that a better hue was obtained on mordented fibers. The results of the anti-bacterial properties of the chrome dyes revealed that the toxicity of these dyes against bacteria is fairly good.

Fabrication of CMC-g-PAM Superporous Polymer Monoliths via Eco-Friendly Pickering-MIPEs for Superior Adsorption of Methyl Violet and Methylene Blue.

Science.gov (United States)

Wang, Feng; Zhu, Yongfeng; Wang, Wenbo; Zong, Li; Lu, Taotao; Wang, Aiqin

2017-01-01

A series of superporous carboxymethylcellulose- graft -poly(acrylamide)/palygorskite (CMC- g -PAM/Pal) polymer monoliths presenting interconnected pore structure and excellent adsorption properties were prepared by one-step free-radical grafting polymerization reaction of CMC and acrylamide (AM) in the oil-in-water (O/W) Pickering-medium internal phase emulsions (Pickering-MIPEs) composed of non-toxic edible oil as a dispersion phase and natural Pal nanorods as stabilizers. The effects of Pal dosage, AM dosage, and co-surfactant Tween-20 (T-20) on the pore structures of the monoliths were studied. It was revealed that the well-defined pores were formed when the dosages of Pal and T-20 are 9-14 and 3%, respectively. The porous monolith can rapidly adsorb 1,585 mg/g of methyl violet (MV) and 1,625 mg/g of methylene blue (MB). After the monolith was regenerated by adsorption-desorption process for five times, the adsorption capacities still reached 92.1% (for MV) and 93.5% (for MB) of the initial maximum adsorption capacities. The adsorption process was fitted with Langmuir adsorption isotherm model and pseudo-second-order adsorption kinetic model very well, which indicate that mono-layer chemical adsorption mainly contribute to the high-capacity adsorption for dyes. The superporous polymer monolith prepared from eco-friendly Pickering-MIPEs shows good adsorption capacity and fast adsorption rate, which is potential adsorbent for the decontamination of dye-containing wastewater.

Fabrication of CMC-g-PAM Superporous Polymer Monoliths via Eco-Friendly Pickering-MIPEs for Superior Adsorption of Methyl Violet and Methylene Blue

Directory of Open Access Journals (Sweden)

Feng Wang

2017-06-01

Full Text Available A series of superporous carboxymethylcellulose-graft-poly(acrylamide/palygorskite (CMC-g-PAM/Pal polymer monoliths presenting interconnected pore structure and excellent adsorption properties were prepared by one-step free-radical grafting polymerization reaction of CMC and acrylamide (AM in the oil-in-water (O/W Pickering-medium internal phase emulsions (Pickering-MIPEs composed of non-toxic edible oil as a dispersion phase and natural Pal nanorods as stabilizers. The effects of Pal dosage, AM dosage, and co-surfactant Tween-20 (T-20 on the pore structures of the monoliths were studied. It was revealed that the well-defined pores were formed when the dosages of Pal and T-20 are 9–14 and 3%, respectively. The porous monolith can rapidly adsorb 1,585 mg/g of methyl violet (MV and 1,625 mg/g of methylene blue (MB. After the monolith was regenerated by adsorption-desorption process for five times, the adsorption capacities still reached 92.1% (for MV and 93.5% (for MB of the initial maximum adsorption capacities. The adsorption process was fitted with Langmuir adsorption isotherm model and pseudo-second-order adsorption kinetic model very well, which indicate that mono-layer chemical adsorption mainly contribute to the high-capacity adsorption for dyes. The superporous polymer monolith prepared from eco-friendly Pickering-MIPEs shows good adsorption capacity and fast adsorption rate, which is potential adsorbent for the decontamination of dye-containing wastewater.

Uso do violeta de alizarina N (AVN como reagente espectrofotométrico na determinação de alumínio Use of the alizarine violet N (AVN as a spectrophotometric reagent for aluminium determination

Directory of Open Access Journals (Sweden)

Alailson Falcão Dantas

2000-04-01

Full Text Available The present work proposes the application of the 4-Hidroxy-3-(2-hydroxynaphtylazo-benzenesulphonic acid (C.I. 15670, Alizarine Violet N (AVN, as a reagent for direct aluminium determination using molecular absorption spectrophotometry in the presence of tensoatives. Al(III cation reacts with AVN in pH 9.4, forming a red complex, stable for at least 24 hours, with absorption minimum at 607nm and, against a reagent blank, (epsiloncomplex - epsilonreagent = -2.71x10(4 L.mol-1.cm-1. The reaction occurs in the presence of a Triton-X100 and CTAB tensoatives mixture, in the presence of EDTA. Al(III determination is possible in the linear range of 50 up to 400ng.mL-1, with a detection limit of 41 ng.mL-1.

Synthesis of magnetic mesoporous metal-organic framework-5 for the effective enrichment of malachite green and crystal violet in fish samples.

Science.gov (United States)

Zhou, Zhihui; Fu, Yanqing; Qin, Qian; Lu, Xin; Shi, Xianzhe; Zhao, Chunxia; Xu, Guowang

2018-07-27

A novel, magnetic and mesoporous Fe 3 O 4 @PEI-MOF-5 material was synthesized for the effective enrichment of malachite green (MG) and crystal violet (CV) in fish samples. The Fe 3 O 4 @PEI-MOF-5 material was prepared by a facile two-step solvothermal approach in which Fe 3 O 4 @PEI and MOF-5 were connected through chemical bonds. Characterization of the newly synthesized Fe 3 O 4 @PEI-MOF-5 material was performed by Fourier transform infrared spectroscopy, X-ray diffractometry, vibrating sample magnetometry, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis and X-ray photoelectron spectroscopy. This new material was determined to have high magnetization and chemical stability, a large surface area and a distinctive morphology. An effective enrichment and detection method for MG and CV was subsequently developed by combining the Fe 3 O 4 @PEI-MOF-5 material with ultra-high-performance liquid chromatography-tandem mass spectrometry. The linearity ranges of this approach for MG and CV were 1-500ng/mL and 0.25-500ng/mL, respectively, with correlation coefficients (R 2 ) of 0.999. The limits of detection (LODs) of the method for MG and CV were 0.30ng/mL and 0.08ng/mL, respectively, indicating that the Fe 3 O 4 @PEI-MOF-5 material had good adsorption properties for MG and CV. Fe 3 O 4 @PEI-MOF-5 can be expected to also provide efficient enrichment of MG and CV in other complex matrices. Copyright © 2018 Elsevier B.V. All rights reserved.

About the Design of QUIC Firefox Transport Protocol

Directory of Open Access Journals (Sweden)

Vraj Pandya

2017-07-01

Full Text Available QUIC (Quick UDP Internet Connections Chrome is an experimental transport layer network protocol designed by Jim Roskind at Google, initially implemented in 2012 and announced publicly in 2013. One of the QUIC's goals is to improve performance of connection-oriented web applications that are currently using the Transmission Control Protocol (TCP. To do that, QUIC achieves a reduced latency and a better stream-multiplexing support to avoid network congestion. In 2015, Firefox Mozilla started to work on an equivalent QUIC transport protocol for their browser. This idea was motivated by the differences between Chrome and Firefox. Despite the fact that Mozilla Firefox and Google Chrome are both web browser engines, there are some significant differences between them, such as file hierarchy, open source policies (Firefox is completely, while Chrome is only partial, tabs design, continuous integration, and more. Likewise QUIC Chrome, QUIC Firefox is a new multiplexed and secure transport based on User Datagram Protocol (UDP, designed from the ground up and optimized for Hyper-Text Transfer Protocol 2 (HTTP/2 semantics. While built with HTTP/2 as the primary application protocol, QUIC builds on decades of transport and security experience, and implements mechanisms that make it attractive as a modern general-purpose transport. In addition to describing the main design of QUIC Firefox, this paper will compare Firefox with QUIC Firefox. Our preliminary experimental results support that QUIC Firefox has a faster execution time, less latency time, and a better throughput time than the traditional Firefox.  

New PVD Technologies for New Ordnance Coatings

Science.gov (United States)

2012-04-01

characteristics using a Tantalum and a Chrome target; 4) Deposition of Ta coatings and reactive deposition of CrN; 5) Deposition parameters affecting film...Vapor Deposition (PVD); High Power Impulse Magnetron Sputtering (HIPIMS); Modulated Pulsed Power (MPP); Tantalum; Chrome ; Ta coatings; CrN; coating...The pre-production chemicals and acids are hazardous and hexavalent Cr is a known carcinogen. Significant annual expenditures are necessary to