Science.gov (United States)

... Both magnesium and aluminium phosphides are therefore potentially more efficient than either calcium or sodium phosphide. ...

UK PubMed Central (United Kingdom)

Improving the anti-demineralizing/remineralizing and mechanical properties of amorphous calcium phosphate (ACP) composites has been the focus of our recent research. In this study, an ethoxylated...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

We have investigated the effect of manganese (Mn) doping on properties of nanosized biphasic calcium phosphate powders and their dense bodies. Manganese levels of 0.6, 1.3, 1.9, 4.3, 7.0 and 11.9at.% were successfully incorporated into biphasic calcium phosphate via a sol-gel route. The prepared powders were calcined at temperatures of 500-1200^oC. The X-ray diffraction analysis revealed that a mix phase comprising of hydroxyapatite and @b-tricalcium phosphate were present, however the content of each phases in the structure was affected by the Mn content. The studies found that the largest portion of @b-tricalcium phosphate was detected at 4.3at.% Mn doping. The incorporation of Mn has also greatly increased the crystallinity of the biphasic calcium phosphate powder due to progressive den...

UK PubMed Central (United Kingdom)

BackgroundCalcium signaling plays an important role in B lymphocyte survival and activation, and is critically dependent on the inositol-1,4,5-tris-phosphate-induced...Full Text Available

UK PubMed Central (United Kingdom)

Brushite (CaHPO₄·2H₂O) was considered to govern the formation of renal calculus of calcium phosphate origin. The degree of saturation of urine with respect to this phase...Full Text Available

UK PubMed Central (United Kingdom)

A novel therapeutic compound was found to induce bladder tumors in male rats. Given the location of the tumors and the increased amounts of calcium- and magnesium-containing solids found in the urine...Full Text Available

UK PubMed Central (United Kingdom)

Transformed Drosophila Kc cell lines, resistant to methotrexate, an inhibitor of de novo purine and pyrimidine synthesis, have been obtained by calcium phosphate transfection of plasmids containing...Full Text Available

Science.gov (United States)

The aim of the current investigation was to study the effects of sevelamer hydrochloride (RenaGel) on serum phosphate, intact parathyroid hormone levels (iPTH), and lipid profiles in stable hemodialysis patients. Hemodialysis patients maintained on calcium containing phosphate binders were enrolled in this study. Following two weeks of washout of the phosphate binders, serum phosphate rose from 6.4 +/- 0.6 to 10.5 +/- 0.7 mg/dl (p <0.001). After 8 weeks of titration with sevelamer hydrochloride, serum phosphate fell by 4.5 +/- 0.3 to 6.3 +/- 0.7 mg/dl (p <0.0001). Serum calcium levels fell during washout (9.8 +/- 0.4 to 8.9 +/- 0.3 mg/dl, p <0.004) and were unaffected by sevelamer hydrochloride. Sevelamer hydrochloride administration was associated with a 23.0 +/- 3.1% fall in total cholesterol, a 35.9 +/- 3.0% fall in LDL ...

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

UK PubMed Central (United Kingdom)

Background: Diet plays a key role in the development of type 2 diabetes (T2D), but little is known about the contributions of specific nutrients in populations in which dietary patterns...Full Text Available

Science.gov (United States)

A laser spectrometer for the ethylenediaminetetra-acetic acid (EDTA) titration of magnesium or calcium ions that is designed around a handheld laser pointer as the source and a photoresistor as the detector is developed. Findings show that the use of the spectrometer reduces the degree of uncertainty and error in one part of the EDTA titrations, however overall standard deviations depend on the skill of the student and their willingness to be careful and precise.

British Library Electronic Table of Contents (United Kingdom)

Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...

Energy Technology Data Exchange (ETDEWEB)

Development was explained of non-phosphate detergent with zeolite (Z) and alpha-olefin sulfonate (AOS). 4A type Z was taken notice of as a builder to replace phosphate. In calcium ion trapping power, conventional sodium tripolyphosphate (STP) and Z are 158mgCaO/g and 150mg/g, respectively. However, because Z by the conventional method is large in crystal diameter, coagulates and adheres to matter to be washed, was newly developed fine Z, 0.9 {mu} m in primary grain diameter, which does not give abrasion nor occlusion to the washing machine, nor precipitate in the river. Because linear alkylbenzene sulfonate, combined with Z, is poorer in washing power than that, done with STP, was developed AOS, new non-phoshate use interfacial active detergent, which is excellent in all washing power, biodegradation speed and physical powder property. Improvement was variously made also in powdery detergent production technology. Though ...

International Nuclear Information System (INIS)

For the treatment of dam waste water containing micro quantities of uranium, the so-called chemical precipitation method is conventionally used, that is, acidic sodium phosphate is added to it and so the uranium (UO_2"2"+) is removed in coprecipitation with the then occurring calcium phosphate (solid). The method, however, has several problems, such as the large space required and large quantities of sludge. For the pupose of eliminating such difficulties and removal and recovery of the uranium, development of the new uranium adsorption method was started. Of the many uranium adsorbents available, excellent ones were selected and then the continuous treatment test was made with small apparatus. Subsequently, the dam waste water uranium recovery facility was completed in 1983. (Mori, K.).

Energy Technology Data Exchange (ETDEWEB)

The use of europium as a local structural probe allows the various phases appearing in the NaCaPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ and NaSrPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ systems to be detected. The broadening of the europium emission lines in going from the calcium to the strontium phases illustrates the ease of displacement of the PO/sub 4/ groups.

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers where feedwater was polluted with sea or river water. Specific effects of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hrs for seawater pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water, denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid, or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high seawater pollution. Soaks cannot stop denting if they are not ...

Science.gov (United States)

INTRODUCTION. We searched for a pathophysiologically based feature of major water electrolytes, which may define water quality better than the water hardness, respecting urinary calculus formation. MATERIALS AND METHODS. Utilizing a multistage stratified sampling, 2310 patients were diagnosed in the imaging centers of the provincial capitals in Iran between 2007 and 2008. These were composed of 1755 patients who were settled residents of 24 provincial capitals. Data on the regional drinking water composition, obtained from an accredited registry, and their relationships with the region's incidence of urinary calculi were evaluated by metaregression models. The stone risk index (defined as the ratio of calcium to magnesium-bicarbonate product in drinking water) was used to assess the risk of calculus formation. RESULTS. No correlation was found between the urinary calculus incidence and the amount of calcium, bicarbonate, or ...

Energy Technology Data Exchange (ETDEWEB)

Pilot plant tests have been conducted to evaluate sodium thiosulfate as an oxidation inhibition additive in five lime/limestone slurry flue gas desulfurization processes. It was found that the oxidation rate of absorbed sulfur dioxide (SO)/sub 2/ was reduced by more than 50 percent in the presence of 100 to 200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvements in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

International Nuclear Information System (INIS)

This study concerns the Souss upstream basin. The objective is to investigate the characteristics of surface water and groundwater, to assess the impact of artificial recharge as reinforcement of the natural replenishment and assess the renewal of groundwater under semi-arid area. Two major water types are observed: (i) surface waters and upstream springs (least mineralized) and (ii) all groundwater samples (prevailing calcium and magnesium bicarbonate water type). Water isotopes show a low evaporation of precipitations during infiltration. Impoverishment in heavy isotopes is the characteristic of mountain rainfalls, or of a climate colder and wetter than present. Carbon-14 activities (34-94 pmc) indicate a long residence time. The artificial recharge is low compared to the reservoir volume, due to which the renewal rate is also low.

British Library Electronic Table of Contents (United Kingdom)

A novel approach using reactive processing is explored that eliminates the labour-intensive separation of post-consumer polyolefin waste from the mixed plastics waste stream. The reactive compatibiliser BMI has been used to form a modified blend of PCPW with 40% improved tensile strength relative to the uncompatibilised control. Addition of 60 wt.-% magnesium hydroxide [Mg(OH)2] during reactive compatibilisation with BMI gave rise to an even more significant enhancement (up to 100%) of the tensile strength. BMI was also able to usefully enhance the properties of a composite based on calcium carbonate and the polyolefin waste.

International Nuclear Information System (INIS)

The study was conducted during 2000 to determine the role of various chemical plant factors viz., total minerals, nitrogen, fat contents, carbohydrate, macro an micro nutrients in the leaves of five genotypes of sugarcane i.e., BF-162, SPSG-26, L-118, CP-43/33 and CP-72/2086 by correlating the infestation of top borer, Scirpophaga Nivella F. at tillering stage. None of the genotype was found completely resistant to the pest. CP-43/33 and BF-162 proved susceptible and resistant varieties, respectively. Total mineral, manganese and copper contents did not show significant correlation with the pest infestation, whereas nitrogen, potassium, calcium, magnesium and ferrous contents played a positive and significant role. Phosphorous, carbohydrates, fats and zinc contents played a significant and negative effect on the pest infestation at tillering stage. (author)

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

In this study, the cytocompatibility of new 'iron-modified/alpha-tricalcium phosphate (IM/alpha-TCP) and calcium sulfate dihydrate (CSD)' bone cement (IM/alpha-TCP/CSD-BC) intended for spinal applications has been approached. The objective was to investigate by direct-contact osteoblast-like cell cultures (from 1 to 14 days) the in vitro cell adhesion, proliferation, morphology and cytoskeleton organization of MG-63 cells seeded onto the new cements. The results were as follows: (a) quantitative MTT-assay and scanning electron microscopy (SEM) showed that cell adhesion, proliferation and viability were not affected with time by the presence of iron in the cements; (b) double immunofluorescent labeling of F-actin and alpha-tubulin showed a dynamic interaction between the cell and its porous substrates sustaining the locomotion phenomenon on the cements' surface, which favored the colonization, and confirming the ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples ...

International Nuclear Information System (INIS)

The difference of NH_4"+-N/NO_3"--N nutrition between hybrid and conventional rice varieties at the late growth stage was studied by using "1"5N-tracer technique. The results showed that the nitrate fertilizer utilization efficiency by the hybrid rice after anthesis was 7.8% higher than that by the ordinary rice variety, and the nitrate fertilizer recovery fraction by the former was 13.2% greater than that by the latter. The varietal difference in NO_3"--N uptake and utilization was almost twice as that in NH_4"+-N. It was also showed that "1"5N distribution in ear of the hybrid rice was about 20% greater than that of the conventional variety, but there were no obvious differences between NO_3"--N and NH_4"+-N. However, "1"5N distribution in the lower node leaves and root was found to be significant higher with NO_3"--N than that with NH_4"+-N in both rice varieties, particularly in the hybrid rice. Compared with NH_4"+-N, NO_3"--N top-dressing before anthesis was observed to have much ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

UK PubMed Central (United Kingdom)

Fasting plasma concentrations of magnesium were measured by neutron activation analysis in 30 non-diabetics and 87 diabetics (55 non-insulin-treated, 32 insulin treated). Plasma concentrations of magnesium...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Gas and plasma nitriding processes were executed in the magnesium with modification by titanium in search for an effective surface treatment method for magnesium alloys. Magnesium-nitrogen system has completely no solid solution or solubility, so that nitride should be only formed by eutectic reaction in the liquid phase. Hence, magnesium is difficult or nearly impossible to have its surface modified by nitriding. Addition of nitride forming element into magnesium enables us to lower the onset temperature of nitriding. Magnesium-titanium alloys with 1 to 5 wt% are yielded by the bulk mechanical alloying and, subjected to gas nitriding for various process conditions. Successful co-formation of Mg{sub 3}N{sub 2} as well as TiN becomes a proof to demonstrate the possibility of gas/plasma nitriding in the solid-state magnesium with aid of ...

International Nuclear Information System (INIS)

The raw materials used in manufacturing of phosphate fertilizer products were derived from rocks. Rocks contain a remarkable of natural radioactivity. Uranium and phosphorous were originally initiated at the same time of the initiated rocks. The purpose of this research is to investigate solubility of uranium phosphate species at the phosphate fertilizer samples, samples including; raw phosphate material, single super phosphates (SSP) granules and powdered, triple super phosphates (TSP) and phosphogypsum samples were obtained from Abu-Zabal factory in Egypt. Solubility of uranium phosphate species was estimated. It was found that, less than half of the uranium phosphate species are soluble in water. The soluble uranium may be enter into the food chains by plant. Therefore, restriction should be done in order to limit ...

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

UK PubMed Central (United Kingdom)

The levels of glucose, sugar phosphates, and adenosine phosphates were determined in primary leaves of intact bean plants during normal senescence and compared to leaves in which senescence was delayed...Full Text Available

UK PubMed Central (United Kingdom)

Ion filtration chromatography on diethylaminoethyl-Sephadex A-25 has been used to separate two isozymes each of triose phosphate isomerase, glyceraldehyde 3-phosphate dehydrogenase, glycerate 3-phosphate...Full Text Available

International Nuclear Information System (INIS)

Studies have shown that CCl_4 administration to rats inhibits endoplasmic reticulum calcium pump activity and reduces the amount of calcium associated with subsequently isolated microsomal subcellular fractions. This report confirms that exposure of isolated hepatocytes to CCl_4 rapidly produces these effects in isolated parenchymal cells and demonstrates that when isolated hepacytes are exposed to CCl_4 calcium is rapidly released from cells. This release can be detected with a calcium ion-selective electrode when cells are incubated in a medium with low extracellular calcium. Calcium released from an intracellular pool(s) may initiate hepatotoxic changes in liver. (author).

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

International Nuclear Information System (INIS)

Quantitative ecological risk assessment (ERA) is a means whereby the risk posed by a toxicant in any system can be evaluated by comparing the distribution of its measured or modelled concentrations (water quality data (WQD)) with available information on the range of concentrations that are known to adversely affect biota within that, or similar, habitats (dose-response data (DRD)). Initially, the WQD are compared with regulatory criteria (e.g. ANZECC and ARMCANZ, 2000). If they fail this test, then, on the assumption that both data sets comprise subsets of the entire range of concentrations, probability density functions are derived assuming a standard distribution form a typically log-normal. In this paper, AQUARISK has been used to estimate the risk posed by copper in effluent from the Rum Jungle mine site, pre- and post-remediation, and the proportion of taxa likely to be affected in the East Branch (EB) of the Finniss River downstream of the mine. In addition, the average ...

International Nuclear Information System (INIS)

The harmful effect of phosphate in yellow cake on the TBP purification process and its removal methods are dealed with. The reason of more uranium loss in residue was analyzed. The harmful effect of phosphate on TBP extraction efficiency and operaton of extraction column was discussed. The limit value of uranium concentration in digestion solution was presented. For TBP purification process, the presence of phosphate in yellow cake does more harm than good. (authors)

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the reaction of zirconium phosphates with carbon tetrachloride in sodium and potassium chloride melt as well as the effect of temperature, gas flow, solubility and weight of the solid phase of the phosphate, and stirring of the melt on the chlorination rate has been studied. The kinetic parameters of the reaction (rate constants, activation energy, etc.) have been calculated.

UK PubMed Central (United Kingdom)

Taste cells use multiple signaling mechanisms to generate appropriate cellular responses to discrete taste stimuli. Some taste stimuli activate G protein coupled receptors (GPCRs) that cause calcium...Full Text Available

UK PubMed Central (United Kingdom)

Background:The cardiac sodium–calcium exchanger (NCX1) is a key sarcolemmal protein for the maintenance of calcium homeostasis in the heart. Since heart failure...Full Text Available

UK PubMed Central (United Kingdom)

Calcium requirements of North American adolescents were set at 1300 mg/day based on data from white girls. Calcium requirements for Asian-American adolescents have not been studied. Using metabolic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Calcium and phosphorus were mainly responsible for reducing the gastrointestinal absorption of lead in human subjects. The effect of calcium was greater than phosphorus, and their combined effect was more than additive. Increasing weights of calcium and phosphorus progressively reduced lead absorption. The relationship between absorption and increasing weights could be described by two negative exponentials. These effects could be explained if lead competed with calcium and phosphorus for common transport mechanisms in the gut. Milk was also found to reduce lead absorption. Adding milk to the diet of people with low dietary calcium intake could reduce the possibility of increased absorption of ingested lead.

Energy Technology Data Exchange (ETDEWEB)

Adsorption of phosphate (PO{sub 4}{sup 3{minus}}) from aqueous solution on activated red mud (ARM) was studied as a function of time, pH, temperature, concentration of adsorbent and adsorbate in acetic acid-sodium acetate buffer medium. The adsorption of phosphate follows Langmuir as well as Freundlich adsorption isotherms. The process efficiency was found to be 80--90% at room temperature. This can be extended to the treatment of industrial effluents containing phosphates like that from phosphatic fertilizer plants.

UK PubMed Central (United Kingdom)

AbstractWe propose a mechanism for the formation of membrane oscillations and traveling waves, which arise due to the coupling between the actin cytoskeleton and the calcium flux through...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Two extruded magnesium alloys, AZ31 and AZ61 were selected to evaluate the influence of process parameters on the material forgeability. The processing parameters considered for forging magnesium alloys were: compression load in the range 55 KN to 60 KN and forging temperature, in the range of ambient temperature to 300 C. Uniaxial compression tests were conducted to establish the strain-temperature relationship. The influences of process parameters on the microstructure were also evaluated. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Measurements of the double-electron-capture process in which a positive ion of iodine becomes a negative ion in a single collision with a magnesium atom are reported between 20 and 90 keV. The cross section is comparable to that for the rare gases and not as large as might be expected from a two-valence-electron atom. This process is probably insignificant in the production of negative ion beams using a magnesium-vapor target.

International Nuclear Information System (INIS)

A new method that allows rapid preconcentration and separation of plutonium and neptunium in water samples was developed for the measurement of "2"3"7Np and Pu isotopes by inductively-coupled plasma mass spectrometry (ICP-MS) and alpha spectrometry. "2"3"8U can interfere with "2"3"9Pu measurement by ICP-MS as "2"3"8UH"+ mass overlap and "2"3"7Np via peak tailing. The method provide enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then moving Pu to DGA resin for additional removal of uranium. The decontamination factor for uranium from Pu is almost 100,000 and the decontamination factor for U from Np is greater than 10,000. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration is performed using a streamlined calcium phosphate precipitation method. Purified solutions are split between ICP-MS and alpha spectrometry so that long and ...

International Nuclear Information System (INIS)

Two different reverse osmosis systems were investigated. The first was a 50-element plant-scale system that is used to treat 2200 m"3 of AECL liquid radwastes annually.It uses thin-film composite (TFC) membranes and operates at an applied pressure of 2760 kPa, with a fixed crossflow of about 40 L/min. The other system uses the same thin-film composite membranes for waste processing but is a two-element pilot-scale system. It is operated at pressures m ranging between 1500 and 7000 kPa, at a fixed crossflow of 55 L/min. The average lifetime of the thin-film composite membranes in the plant-scale processing application at AECL is about 3000 h. After this service life has expired the rejection efficiency declines rapidly from 99.5% to about 95% as the membranes become impaired from chemical cleaning procedures that are required after each 100 m"3 of waste is treated. The permeation flux for the plant-scale system decreases from about 2.2 L/min/element to below 0.5 L/min/element at the end ...

International Nuclear Information System (INIS)

We studied the effect of extracellular Ca"2"+ concentration ([Ca"2"+]_e) on adipocyte differentiation. Preadipocytes exposed to continuous [Ca"2"+]_e higher than 2.5 mmol/l accumulated little or no cytoplasmic lipid compared to controls in 1.8 mmol/l [Ca"2"+]_e. Differentiation was monitored by Oil Red O staining of cytoplasmic lipid and triglyceride assay of accumulated lipid, by RT-PCR analysis of adipogenic markers, and by the activity of glycerol-3-phosphate dehydrogenase (GPDH). Elevated [Ca"2"+]_e inhibited expression of peroxisome proliferator-activated receptor #gamma#, CCAAT/enhancer binding protein #alpha#, and steroid regulatory binding element protein. High [Ca"2"+]_e significantly inhibited differentiation marker expression including adipocyte fatty acid binding protein, and GPDH. The decrease in Pref-1 expression that accompanied differentiation also was prevented by high [Ca"2"+]_e. Treatment of 3T3-L1 cells with high [Ca"2"+]_e did not significantly ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are being increasingly utilized in a variety of fields as an alternative material to organic materials and aluminum alloys, owing to excellent properties. Those include low density, and excellent damping properties. When compared to organic materials, furthermore, Mg alloy excels at recyclability, heat radiation, and electromagnetic-shielding. Though most of magnesium alloy products are manufactured through die-casting and thixo-molding at present, the demand for the expanding of magnesium wrought alloy market is increasing. Taking full advantage of a drawing technique and applying it to the conventional extruded pipe, we have developed a new type of magnesium alloy pipe. The strength of the developed pipe is significantly higher than that of the conventional one, either extruded or die-casting. Some of the excellent properties were obtained from fundamental tests performed with the ...

International Nuclear Information System (INIS)

An experimental approach has been performed to ascertain the effectiveness of semi-solid strip casting using a horizontal twin roll caster. The demand for light-weight products with high strength has grown recently due to the rapid development of automobile and aircraft technology. One key to such development has been utilization of magnesium alloys, which can potentially reduce the total product weight. However, the problems of utilizing magnesium alloys are still mainly related to high manufacturing cost. One of the solutions to this problem is to develop magnesium casting-rolling technology in order to produce magnesium sheet products at competitive cost for commercial applications. In this experiment, magnesium alloy AZ31B was used to ascertain the effectiveness of semi-solid roll strip casting for producing magnesium alloy sheets. The temperature of the ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

PMID:11506019

UK PubMed Central (United Kingdom)

In superior cervical ganglion (SCG) neurons calcium-induced calcium release (CICR), mediated by ryanodine receptors (RyRs), contributes to stimulation-evoked intracellular calcium ([Ca²⁺]_i)...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

To apply the CO{sub 2} absorber at about 1000{sup o}C for integrated coal gasification combined cycle (IGCC) furnace, the reactions of calcium oxide and CO{sub 2} at high temperatures was examined. Calcium carbonate reacts with sodium hydrogen carbonate below 200{sup o}C and forms sodium-calcium complex carbonate. The sodium-calcium complex carbonate melts at 813{sup o}C, and the carbon dioxide absorption and discharge reversible reactions of calcium-oxide takes place via liquid at around 1000{sup o}C. Sintering of calcium oxide at high temperature has been successfully avoided by the addition of sodium.

UK PubMed Central (United Kingdom)

Trypanosoma brucei contains two isoenzymes for glyceraldehyde-phosphate dehydrogenase (GAPDH); one enzyme resides in a microbody-like organelle, the glycosome, the other one is found in the cytosol....Full Text Available

UK PubMed Central (United Kingdom)

The effect of TP (triosephosphates:glyceraldehyde-3 phosphate, GAP, +dihydroxyacetone phosphate, DHAP) on respiration, phosphorylation and matrix ATP/ADP ratios of isolated oat mesophyll mitochondria...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Qualitative and quantitative methods have been developed to relate phosphate/UO{sub 2} interactions and U dissolution, in vitro, in a medium containing 0 or 10 mM phosphate concentrations at pH 5. This was performed by Energy Dispersive X ray Spectrometry (EDS) at 200 kV on entire particles and by fluorimetric measurement. The U dissolution rate was larger in a medium without phosphate than in a medium containing 10 mM phosphate. During the first day, the initial U dissolution involved 80.55% and 91.13% of the powder in media with and without phosphate respectively. From 5 to 15 d after beginning the assay, the dissolution half-times were longer than 92 d and 22 d for media with and without phosphate. EDS analyses have shown a constant P/U X ray intensity ratio for reference U{sub 2}O(PO{sub 4}){sub 2} for the same range of particle diameter. A gradual increase ...

UK PubMed Central (United Kingdom)

Pyrophosphate:fructose-6-phosphate phosphotransferase (PFP) was purified over 500-cold from endosperm of germinating castor bean (Ricinus commiunis L. var. Hale). The kinetic properties...Full Text Available

UK PubMed Central (United Kingdom)

The reaction of iodine with glyceraldehyde 3-phosphate dehydrogenase from Bacillus stearothermophilus was investigated. The active-site thiol group of the cysteine residue homologous with cysteine-149...Full Text Available

UK PubMed Central (United Kingdom)

Glyceraldehyde-3-phosphate dehydrogenase (GAPDH), an evolutionarily conserved glycolytic enzyme, is constitutively expressed in most cell types yet is induced to high levels during the development of...Full Text Available

International Nuclear Information System (INIS)

Zirconium phosphate was one of the earliest inorganic ion-exchange suggested for removing strontium and cesium from aqueous nuclear waste. This paper studied ionic exchange to remove Cs-137 and Sr-90 by using different cationic of zirconium phosphate. In this case the parameters studied were the effect of temperature and ion concentration to percent up take and distribution coefficients. It is also conducted the study on column experiments to determine the breakthrough curves for Cs-137 and Sr-90. The result showed the potential of use of zirconium phosphate in radioactive waste treatment. (author)

Energy Technology Data Exchange (ETDEWEB)

Promoted antimony phosphate oxide complexes are excellent catalysts for the ammoxidation of methanol to HCN especially at high methanol throughputs.

UK PubMed Central (United Kingdom)

The metabolism of pentose-phosphate was investigated in Plasmodium falciparum-infected normal and glucose-6-phosphate dehydrogenase (G6PD)-deficient human red blood cells in vitro. 5'-Phosphoribosyl-1-pyrophosphate...Full Text Available

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium is known to have poor formability at room temperature, mainly attributed to its hexagonal lattice structure. This paper presents the findings generated from development of warm forming to produce thin-walled magnesium components. Finite element analysis was conducted to evaluate the formability of the material and the simulated results were compared to the tensile results and product formability. Tensile tests were used to verify the formability of the sheet metal at difference temperatures. The process parameters considered in the feasibility study were forming temperature, in the range of 28 C to 300 C and magnesium sheet (AZ31B-H24) thickness, in the range of 0.4 mm to 1 mm. Magnesium hand phone covers of a thickness down to 0.4 mm have been successfully produced. The feasible forming temperature was found to be between 200 C and 250 C. Metallographic examination shows evident of ...

Energy Technology Data Exchange (ETDEWEB)

The effects of carbon inoculation by C{sub 2}Cl{sub 6} addition were investigated using commercial AZ31 magnesium alloy. The additions of C{sub 2}Cl{sub 6} to AZ31 magnesium alloy significantly reduce the grain size from 280 {mu}m to about 120 {mu}m and the tensile properties are also increased due to grain refinement. EPMA analysis shows that Al-C-O compounds are formed in the castings which are considered to function as nucleants. (orig.)

Science.gov (United States)

Increasing the Mg(2+) concentration results in a depression of succincoxidase-linked state 3

Energy Technology Data Exchange (ETDEWEB)

A new technique has been developed for improving corrosion resistance on magnesium alloys. Specimens of AZ31 magnesium alloy were dipped into molten salt of NaBF{sub 4} at 723 K for various times, and then cooled, rinsed with water, and dried in air. Corrosion resistance in the surface treated specimens was evaluated by salt immersion test using 1% NaCl solution as a time for occurring filiform corrosion. On an un-treated AZ31 alloy, the time for starting the filiform corrosion was about 1.2 ks, while on the surface treated specimen, the time was prolonged into about 1300 ks. Moreover, the surface treated specimen showed corrosion resistance in low pH solutions, such as 1% HNO{sub 3} and HCl solutions. (orig.)

UK PubMed Central (United Kingdom)

Hypocalcemia in the hypomagnesemic state in man is usually attributed to refractoriness of end-organs to the calcemic action of parathyroid hormone. We studied the responsiveness of end-organs to bovine...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A new interest in magnesium alloys has arisen since light-weight constructions have become more and more attractive. Products that are currently available are mostly cast, forged, and extruded. A cost-effective production of sheet metals will render new perspectives in the design of light-weight constructions. The development of new casting technologies like thin slab casting or strip casting with an in-line rolling process is expected to result in a shorter processing time featuring a high potential of saving energy, time, and cost. Particular attention is paid to the casting process parameters such as casting speed and solidification speed. This article deals with some aspects of a magnesium-adapted single-belt caster. Results of casting experiments and material examination are shown as well as some advices given concerning safety and handling of liquid magnesium. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.

British Library Electronic Table of Contents (United Kingdom)

Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...

Energy Technology Data Exchange (ETDEWEB)

A type of mesoporous ZrO{sub 2} was synthesized and its phosphate removal potential was investigated in this study. The adsorption isotherm, pH effect, ionic strength effect and desorption were examined in batch experiments. The adsorption data fitted well to the Langmuir model with which the maximum P adsorption capacity was estimated to be 29.71 mg P/g. The amount of phosphate adsorbed increased rapidly in the first 5 h and slowly towards the end of the run, suggesting the possible monolayer coverage of phosphate ions on the surface of the adsorbent. The phosphate adsorption tended to increase with a decrease of pH and an increase of ionic strength. A phosphate desorbability of approximately 60% was observed with 0.5 M NaOH, which indicated a relatively strong bonding between the adsorbed PO{sub 4}{sup 3-} and the sorptive sites on the surface of the adsorbent. The immobilization ...

UK PubMed Central (United Kingdom)

Verapamil administered before treatment, but not after treatment, had a beneficial effect on a 90-minute warm ischemia-reperfusion rat liver injury model. The possible activation of proteases converting...Full Text Available

UK PubMed Central (United Kingdom)

The homologous sequences observed for many calcium binding proteins such as parvalbumin, troponin C, the myosin light chains, and calmodulin has lead to the hypothesis that these proteins have homologous...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundCalcium homeostasis is a known target of several environmental toxicants including lead and mercury.ObjectiveOur goal was to determine...Full Text Available

UK PubMed Central (United Kingdom)

Large-conductance voltage- and calcium-activated potassium (BK) channels have been shown to play a role in detrusor overactivity (DO). The goal of this study was to determine whether bladder outlet...Full Text Available

Science.gov (United States)

Names Ca+2; Serum calcium; Ca++ References Wysolmerski JJ, Insogna KL. The parathyroid glands, hypercalcemia, and hypocalcemia. In: Goldman L, Ausiello D, eds. Cecil...

UK PubMed Central (United Kingdom)

T-type calcium channels are responsible for generating low-threshold spikes that facilitate burst firing and neurotransmitter release in neurons. GnRH neurons exhibit burst firing, but the underlying...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This patent describes a preflush fluid for preventing lost circulation during the cementing of a well, the fluid consisting essentially of: (a) water; (b) about 10 to about 30 percent by weight of water (% BWOW) cement; (c) about 5 to about 30% BWOW calcium sulfate selected from the group consisting of calcium sulfate hemihydrate, calcium sulfate dihydrate, and mixtures thereof; and (d) an alkali metal-containing quick-hardening accelerator.

International Nuclear Information System (INIS)

A technique has been developed for joining a large calcium fluoride crystal to a stainless-steel flange by means of a silver transition ring. The process involves both vacuum brazing using a copper-silver alloy and air brazing using silver chloride. This paper describes the procedure used in fabricating a high-vacuum leak-tight calcium fluoride window assembly.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys and composites are potentially highly attractive materials for lightweight design in the automotive industry - if common forming technologies, i.e., deep drawing and cold extrusion, are applicable to them; so far, this is seldom the case. The authors have tested some candidate Mg alloys and discuss the results of their measurements in detail. The Figure shows a typical workpiece part obtained by a deep-drawing technique. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys have replaced resins as a material for the components of electronic products such as cell phone and notebook personal computer mainly, because of their lightness and rigidity. Thin walls, a complicated shape, and high appearance quality are all needed in the external parts. Die-casting and injection molding are the main method of manufacturing magnesium alloy parts. The optimal cast conditions and mold design have been investigated in order that a few defects such as surface cracks and mold cavities in casting parts would be reduced. Instead of cast, plastic forming technologies such as warm drawing and hot forging have been developed to form thinner walls and less defects. Plastic formability of magnesium alloy in hot working is dependent on a grain size of material. The material with fine grains has advantage of being formed at high strain rate. The characteristics of forming processes of ...

Energy Technology Data Exchange (ETDEWEB)

Machines and structures, such as automobiles are usually subjected to biaxial or three-axial stresses instead of uniaxial stress. However, research on a fatigue failure under multi-axial stress has not been fully presented because such experiments are difficult. To solve this problem, we developed the servo biaxial fatigue-testing machine. In this research, we performed the biaxial fatigue tests of a magnesium alloy in order to clarify the effects from different heat treatments. Magnesium alloy is the lightest in weight among metal materials for structural use. The fatigue characteristics of a magnesium alloy are indispensable in order to create the design which ensures the reliability and the safety of the vehicles especially in long-distance run. The main conclusions are summarized as follows; (1) The mechanical property of magnesium alloy AZ31B falls by heat treatment at low temperature. (2) The ...

British Library Electronic Table of Contents (United Kingdom)

The biosorption of phosphate from aqueous solutions using Fe(III)-treated Staphylococus xylosus cells was investigated. Langmuir and Freundlich isotherm models were applied to describe the adsorption equilibrium and found that Langmuir isotherm model fitted the equilibrium data better than Freundlich isotherm model. The biosorption capacity of Fe(III)-treated biomass for phosphate was found to be 70.92mg/g at optimum conditions of pH 3.0, biomass concentration 0.5g/L and equilibrium phosphate-biomass time 60min respectively. The sorption efficiency at initial phosphate concentration of 50mg/L was not influenced upon addition of SO4^2^-, Cl^-, CO3^2^-, NO3^-, Mg^2^+ and Ca^2^+ ions from 0 to 800mg/L, whereas under the same conditions, phosphate sorption was increased with increase in concen...

International Nuclear Information System (INIS)

The phosphate complexation of Np(V) is investigated in the pH range from 6.4 to 10.0 in 0.1 M NaClO_4 at 22#+-#2 C by absorption spectroscopy. The formation of two phosphate complexes is confirmed by spectroscopic speciation: NpO_2HPO"-_4 at 988.8 nm and NpO_2PO"2"-_4 at 993.6 nm with molar extinction coefficients of 251#+-#8 and 201#+-#11 1/mol cm, respectively. The complexation constants are determined to be log #beta# = 2.54#+-#0.02 for NpO_2HPO"-_4 and log #beta# = 6.33#+-#0.08 for NpO_2PO"2"-_4. The competition of the phosphate complexation with the carbonate complexation is demonstrated by speciation calculation under different geochemical conditions. (orig.).

Energy Technology Data Exchange (ETDEWEB)

New phosphates with NaZr{sub 2}(PO{sub 4}){sub 3} structure of the B{sub 0.5}FeTa(PO{sub 4}){sub 3}-type (where B-Ca, Sr, Ba) are synthesized and characterized by X-ray diffraction analysis and IR-spectroscopy. The heating behavior of the phosphates is studied using high-temperature X-ray crystallography in the range 15-625 deg. C. The unit-cell parameters, the coefficients of thermal expansion {alpha}{sub a}, {alpha}{sub c} and their thermal expansion anisotropy |{alpha}{sub c} - {alpha}{sub a}| of the phosphates under study are determined and the dependences of these characteristics on the nature of cations are established and analyzed.

International Nuclear Information System (INIS)

An experimental study on superplastic forming behaviors and microstructure characters of commercial magnesium alloy sheet AZ31B is presented in this paper. The main experimental results show that the commercial magnesium alloy AZ31B sheet has superplastic capability. For the received sheet without any pre-processing, the maximum elongation is 295%. The dynamic recrystallization and grain refinement can be found, In the case of temperature =# 350 deg. C. The superplastic behaviors can be improved by controlling the dynamic recrystallization and grain refinement. Some experimental results of free superplastic bulging are presented in this paper. The results show that influence of temperature on forming capability is much less than the influences of temperature on elongation. In addition, the maximum principle strain.

Energy Technology Data Exchange (ETDEWEB)

Materials and processing designs for advanced magnesium alloys with fine microstructures and superior properties were established by the combination of the repeated plastic working and the Mg{sub 2}Si synthesis in solid-state. The grain size was less than 1 {mu}m via RPW process due to its severe plastic working on raw powder. The hot extruded magnesium alloys produced in industries showed high ultimate tensile strength, e.g. 420{proportional_to}450 MPa, when employing Mg-Zn-Al-Ca-RE (Rare Earth) alloy coarse powder, having 0.5{proportional_to}2 mm diameter, as input materials. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Following the breakthrough for cast magnesium products, interest is now spreading to wrought applications - triggering a variety of technological questions. A major bottleneck in the manufacture of magnesium sections (profiles) by conventional hot extrusion is the low productivity, with extrusion speeds typically five to ten times lower than for comparable aluminium sections. This paper focuses on the use of hydrostatic extrusion as a means to overcome this problem. On the basis of an analytical model, it is clarified why and how process limits are affected by the process mechanics. Experimental work on the hydrostatic extrusion of the alloys M1A, ZM21 and AZ31 confirms that extrusion speed is indeed multiplied, whereas the resulting mechanical properties are similar to or better than those for conventional extrusions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, r-values and their relation to the ...

UK PubMed Central (United Kingdom)

Model phosphate-metal solvation complexes have been studied by ab-initio self-consistent-field techniques. The complexes studied include (RO)2PO2-(R = H or CH3) with Li+, Na+, K+, Be++, Mg++, Ca++,...Full Text Available

UK PubMed Central (United Kingdom)

A soluble enzyme system from suspension cultures of Acer pseudoplatanus L. converts d-glucose 6-phosphate to myoinositol. A Mg²⁺-dependent phosphatase, present in...Full Text Available

International Nuclear Information System (INIS)

Paper estimates the corrosion resistance and studies the character of dissolving of silicon-bearing austenite stainless steels in strongly oxidizing media containing phosphate and fluoride admixtures. Corrosion behaviour of the studied steels is determined to depend essentially on the content of admixture or alloying silicon, as well as, on their phase composition in many respects determined by the thermal treatment condition. Refs. 22, figs. 1, tabs. 2.

Energy Technology Data Exchange (ETDEWEB)

The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to ...

International Nuclear Information System (INIS)

Luminescence and reflection spectra as well as luminescence kinetics of the 1 mol% Sm3+-doped crystalline lanthanum magnesium meta borate (LaMgB5O10) and gadolinium magnesium meta borate (GdMgB5O10) were analyzed. Materials were synthesized by conventional solid state route and showed bright orange-red emission under UV excitation. Emission spectra contain sharp and well resolved Sm3+4G5/2#->#6HJ transitions indicating a strong crystal-field effect. In case of gadolinium compound energy transfer between Gd3+ and Sm3+ was detected. The luminescent kinetics of the Sm3+ in analyzed powders is characterized by single exponential decay and experimental values vary in the range 2.2-2.4 ms. - Research highlights: ? Phosphorescence of samarium-doped lanthanide magnesium meta borates. ? Bright and well resolved orange-red emission of Sm3+ under UV excitation. ? Energy transfer from Gd3+ to Sm3+ in gadolinium ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this study as to determine the mechanisms involved in using ammonium fluoborate as a reducing atmosphere when preheating a high magnesium content aluminium alloy. Rutherford Backscattering (RBS) has been the major technique used in the analysis of samples, it revealed significant reduction in both the diffusion of magnesium to the surface and the calculated oxide thickness in the presence of NH{sub 4}BF{sub 4}. At temperatures above 500 deg C in air, SEM images revealed depressions and voids due to incipient melting at various stages, around the grain boundaries. Grain boundaries effectively acted as pipes aiding the diffusion of magnesium to the surface. These results have been verified through compositional analysis with both RBS and auger electron spectroscopy (AES). Results from NH{sub 4}BF{sub 4} atmosphere preheat conditions showed significant improvements. It was verified experimentally that above 500 deg ...

Science.gov (United States)

The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.

Science.gov (United States)

The biocompatibility and corrosion resistance of various materials for use as sacrificial anodes in in vivo hybrid fuel cells were studied. Aluminium, zinc, and magnesium alloy AZ31B were studied, and the results are discussed.

Energy Technology Data Exchange (ETDEWEB)

The fertilizer contribution to radio uptake by tomato plants was assessed. Tomato and soil samples from four different plantations were analyzed: two using organic fertilizer and two using phosphate fertilizer. The Ra concentrations in eight of the most used tomato fertilizers were determined. The concentration values ranged from 14 to 221 Bq/kg of Ra-226 and from 25 to 176 Bq/kg of Ra-228. Owing to the low Ra concentration and to the used fertilizer quantities, the fertilizers would not increase significantly the Ra soil concentration. However, the highest soil to plant concentration ratios were found in the plantations using phosphate fertilizers. This outcome pointed out the higher Ra availability in the phosphate fertilizer plantations than in the organic fertilizer plantations, showing a possible positive influence of phosphate fertilizers for the tomato Ra uptake. Due to the ...

Energy Technology Data Exchange (ETDEWEB)

Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Optimum conditions for microstructural control in industrial hot working of cast and homogenized AZ31 magnesium alloys are evaluated by using a processing map. The recommended window for bulk metal working of this alloy is the domain in the temperature range 300-450 C and strain rate range 1-10 s{sup -1}, and the optimum processing parameters are 400 C and 10 s{sup -1}, where grain-boundary self diffusion is the rate-controlling mechanism. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The superplastic characteristics and diffusion bonding behaviors were investigated in commercial 7475 aluminum alloy and AZ31 magnesium alloy sheets. In this study, the presently used materials behaved in a superplastic manner at {proportional_to} 773 K (7475Al) and {proportional_to} 523 K (AZ31). Then, by the theoretical relationship between pressure and time, these materials were successfully diffusion bonded at the superplastic temperatures. The bonding strength was more than 65 MPa. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Drosophila melanogaster is a model organism rich in genetic tools to manipulate and identify neural circuits involved in specific behaviors. Here we present a technique for two-photon calcium imaging in the central brain of head-fixed Drosophila walking on an air-supported ball. The ball's motion is tracked at high resolution and can be treated as a proxy for the fly's own movements. We used the genetically encoded calcium sensor, GCaMP3.0, to record from important elements of the motion-processing pathway, the horizontal-system lobula plate tangential cells (LPTCs) in the fly optic lobe. We presented motion stimuli to the tethered fly and found that calcium transients in horizontal-system neurons correlated with robust optomotor behavior during walking. Our technique allows both behavior ...

International Nuclear Information System (INIS)

... calcium 47 combustion dry ashing high temperature labelled compounds lead

British Library Electronic Table of Contents (United Kingdom)

Abstract Although photosynthetic thermotolerance has been investigated extensively in cotton leaves, reports on the biochemical influence of the pistil in promoting fertilization thermostability are limited. To evaluate the effect of temperature, genotype, and exogenous calcium application on fertilization and pistil biochemistry in cotton, thermosensitive (cv. ST4554 B2RF) and thermotolerant (cv. VH260) plants were grown under control (30/20-C) or high-temperature (38/20-C) conditions during flowering, and exogenous CaCl2 was applied to flowers 1-day prior to anthesis. Measured pistil parameters included fertilization efficiency; protein concentration; glutathione reductase, superoxide dismutase (SOD) and NADPH oxidase activities; and ATP and calcium levels. Exogenous calcium had no effec...

International Nuclear Information System (INIS)

... activation analysis aluminium 28 calcium 49 chlorine 38 cotton plants li-drifted

International Nuclear Information System (INIS)

Chinese brake fern (Pteris vittata L.), an arsenic (As) hyperaccumulator, has shown the potential to remediate As-contaminated soils. This study investigated the effects of soil amendments on the leachability of As from soils and As uptake by Chinese brake fern. The ferns were grown for 12 weeks in a chromated-copper-arsenate (CCA) contaminated soil or in As spiked contaminated (ASC) soil. Soils were treated with phosphate rock, municipal solid waste, or biosolid compost. Phosphate amendments significantly enhanced plant As uptake from the two tested soils with frond As concentrations increasing up to 265% relative to the control. After 12 weeks, plants grown in phosphate-amended soil removed >8% of soil As. Replacement of As by P from the soil binding sites was responsible for the enhanced mobility of As and subsequent increased plant uptake. Compost additions facilitated As uptake from the CCA soil, but decreased As ...

Energy Technology Data Exchange (ETDEWEB)

Earlier studies have indicated that xylitol may increase the absorption and urinary excretion of dietary oxalate. It has also been indicated that xylitol increases the absorption of calcium. Intestinal absorption of lead, a divalent contaminant in the diet, is in many respects similar to that of calcium. The purpose of this study was to evaluate the effects of xylitol on the intestinal absorption of lead using two different approaches: the in situ ligated intestinal loop technique in cockerels and gastric gavage in mice.

Energy Technology Data Exchange (ETDEWEB)

The distribution of the alkaline earth elements strontium and barium between the solid phases of phosphates of transition elements of group 4 and chloride melts was studied. The distribution coefficients of strontium and barium were found at T = 700-800/sup 0/C. Phosphates of the type NaM/sub 2//sup (IV)/(PO/sub 4/)/sub 3/, where M/sub (IV)/ represents titanium, zirconium, and hafnium, were used as the solid phases. It was established that there is an enrichment of the precipitates with the distributed components. The distribution coefficient depends on the nature of the solid phase and the temperature. It was suggested that M/sup (II)/ x M/sub 4//sup (IV)/(PO/sub 4/)/sub 6/ is formed in processes of distribution, where M/sup (II)/ represents Sr, Ba.

British Library Electronic Table of Contents (United Kingdom)

Please cite this paper as: Ectopic mineralization of connective tissue in Abcc6-/- mice: effects of dietary modifications and a phosphate binder - a preliminary study. Experimental Dermatology 2008; 17: 203-207. Abstract: Pseudoxanthoma elasticum (PXE), a heritable multisystem disorder, is caused by mutations in the ABCC6 gene. We have developed a murine model for PXE by targeted inactivation of the corresponding mouse gene. A feature of this mouse model is ectopic mineralization of connective tissue capsule surrounding the bulb of vibrissae. This study was designed to investigate the effect of dietary sevelamer hydrochloride (Renagel), a phosphate binder, and specific mineral modifications on ectopic mineralization of connective tissue in Abcc6-/- mice. Three groups were fed a specific di...

Energy Technology Data Exchange (ETDEWEB)

In this, the last of a series of three papers, we discuss a method of forming iron phosphate ceramics by a reduction process. We report the formation of iron oxide ceramics by reducing hematite with iron in a phosphoric acid solution. The reaction results in a rapid-setting ceramic (at room temperature) with a compressive strength of 3700 psi and a density of 1.7 g/cm{sup 3}. Although the exact mineral form of the binder is difficult to determine because it is mostly amorphous and hence is not amenable to X-ray diffraction analyses, this material is expected to consist of iron hydrophosphates. The reduction process is very useful in recycling several industrial wastes that are rich in hematite, including iron mine tailings, red mud (a caustic waste from the alumina industry), and machining swarfs. Formation of ceramics with red mud and swarfs is also discussed.

Energy Technology Data Exchange (ETDEWEB)

The role played by calcium sulfite in the flue gas desulfurization of lime/limestone scrubbers makes it desirable to work out its thermodynamic properties. A thermogravimetric apparatus was used to study the equilibria between calcium sulfite hemihydrate and calcium sulfite anhydrite under different conditions. Efforts were made to analyze the difficulties encountered in the dynamic approach to equilibration after calcium sulfate dihydrate failed in calibration of the apparatus. Finally, the kinetics and thermodynamics for the dissociation of calcium sulfite hemihydrate were examined. The confirmation of Engel-Brewer's correlation between the electronic configuration and crystal structure in metallic systems has long been pursued in this group by studying the Lewis-acid-base interactions. Tantalum-iridium alloys of different compositions were brought into equilibrium with ...

UK PubMed Central (United Kingdom)

The phosphatidylinositol pathway is implicated in the regulation of numerous cellular functions and responses to extracellular signals. An important branching point in the pathway is the phosphorylation...Full Text Available

UK PubMed Central (United Kingdom)

1. Sacs 20 cm long were obtained from the upper half of the small intestine of bile fistula rats (bile duct cannulated 48 hours previously). The sacs were everted, filled with oxygenated phosphate...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Sucrose phosphate synthase (SPS) catalyzes the transfer of a glycosyl group from an activated donor sugar, such as uridine diphosphate glucose (UDP-Glc), to a saccharide acceptor D-fructose 6-phosphate (F6P), resulting in the formation of UDP and D-sucrose-6'-phosphate (S6P). This is a central regulatory process in the production of sucrose in plants, cyanobacteria, and proteobacteria. Here, we report the crystal structure of SPS from the nonphotosynthetic bacterium Halothermothrix orenii and its complexes with the substrate F6P and the product S6P. SPS has two distinct Rossmann-fold domains with a large substrate binding cleft at the interdomain interface. Structures of two complexes show that both the substrate F6P and the product S6P bind to the A-domain of SPS. Based on comparative analysis of the SPS structure with other related enzymes, the donor substrate, nucleotide diphosphate glucose, binds to the ...

UK PubMed Central (United Kingdom)

Phospho-beta-galactosidase (P-beta-gal), the enzyme which catalyzes the first step in the metabolism of intracellular lactose phosphate, occurred at high specific activity in the cytoplasm in 12 of...Full Text Available

UK PubMed Central (United Kingdom)

The effect of different nitrogen compounds on the induction of reduced nicotinamide adenine dinucleotide phosphate-nitrate reductase was examined in Neurospora crassa. Whereas in the wild-type strain...Full Text Available

UK PubMed Central (United Kingdom)

Nutrient transport affinities of nutrient-starved microbial populations were measured as initial slopes of plots of limiting-nutrient transport rates versus extracellular limiting-nutrient concentrations....Full Text Available

UK PubMed Central (United Kingdom)

The formation of the nicotinamide adenine dinucleotide phosphate-dependent formate dehydrogenase in Clostridium thermoaceticum is stimulated by the presence of molybdate and selenite...Full Text Available

International Nuclear Information System (INIS)

High-resolution proton nuclear magnetic resonance spectroscopy has been used to investigate the molecular mechanism of the Bohr effect of human normal adult hemoglobin in the presence of two allosteric effectors, i.e., chloride and inorganic phosphate ions. The individual hydrogen ion equilibria of 22-26 histidyl residues of hemoglobin have been measured in anion-free 0.1 M HEPES buffer and in the presence of 0.18 M chloride or 0.1 M inorganic phosphate ions in both deoxy and carbonmonoxy forms. The results indicate that the #beta#2-histidyl residues are strong binding sites for chloride and inorganic phosphate ions in hemoglobin. The affinity of the #beta#2-histidyl residues for these anions is larger in the deoxy than in the carbonmonoxy form. Nevertheless, the contribution of these histidyl residues to the anion Bohr effect is small due to their low pK value in deoxyhemoglobin in anion-free solvents. The interactions of ...

International Nuclear Information System (INIS)

The effect of pigments on the development of corrosion products between the painting system and metal surface when exposed to marine environments has been discussed. The pigments studied were: red mud zinc chromate, zinc chromate, red oxide zinc phosphate, manganese phosphate barium chromate and basic lead silico chromate. Moessbauer spectroscopy revealed that the upper rust layer in all the cases consisted of #gamma#-Fe_2O_3, #gamma#-FeOOH and #alpha#-FeOOH. The lower rust layer immediately in contact with the metal surface consisted of an asymmetrical doublet due to #gamma#-FeOOH. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Crystal structure of monoclinic telluric acid ammonium phosphate (TAAP) has been studied by an X-ray diffraction method in the paraelectric phase at 333 K and in the ferroelectric phase at room temperature. It is confirmed that the space group in the paraelectric phase is P2/n. Comparison of the results between the two temperatures suggests that the plane which is made by the PO{sub 4} tetrahedron linked by hydrogen bonds has an important role for the ferroelectric phase transition. This plane is almost parallel to the direction of spontaneous polarization.

Energy Technology Data Exchange (ETDEWEB)

Arsenic in soils from the Asarco lead smelter in East Helena, Montana was characterized by X-ray absorption spectroscopy (XAS). Arsenic oxidation state and geochemical speciation were analyzed as a function of depth (two sampling sites) and surface distribution. These results were compared with intensive desorption/dissolution experiments performed in a pH stat reactor for samples from the site with the highest degree of As heterogeneity. The objectives of the study were to investigate the solid-phase geochemical As speciation, assess the speciation of As in solutions equilibrated with the solids under controlled pH (pH=4 or 6) and Eh (using hydrogen or air) environments, observe the effects of phosphate on the release of As into solution, and examine the effects of phosphate on metal mobility in the systems. Arsenic was predominantly found in the As(V) valence state, though there was evidence that As(III) and As(0) were present also. The ...

International Nuclear Information System (INIS)

The mechanism of lead transport is presented, and especially the particular similarities or dissimilarities between lead and calcium in this process. The absorption of these metals was determined cockerels, raised on a commercial diet or on a specified diet, using in vivo ligated loop procedure. The dose administered into the loop contained 0.5 #mu#Ci "2"0"3Pb (and/or 0.1 #mu#Ci "4"7Ca), and 0.01 mM lead acetate (and/or mM CaCl_2) in 0.5 ml 0.15 M NaCl,pH 6.5. It was shown that lead is rapidly taken up by the mucosal tissue, and slowly transferred into the body, whereas less calcium is retained by the tissue and the transfer of calcium is many times as effective as that for lead. They appear to respond in a similar manner to a low calcium intake and vitamin D treatment. Increasing luminal stable lead concentration significantly reduced the percentage of radiolead significantly reduced the percentage of ...

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

The experiment was carried out on a short rotation coppice culture of poplars (POP-EUROFACE, Central Italy), growing in a free air carbon dioxide enriched atmosphere (FACE). The specific objective of this work was to study whether elevated CO{sub 2} and fertilization (two CO{sub 2} treatments, elevated CO{sub 2} and control, two N fertilization treatments, fertilized and unfertilized), as well as the interaction between treatments caused an unbalanced nutritional status of leaves in three poplar species (P. x euramericana, P. nigra and P. alba). Finally, we discuss the ecological implications of a possible change in foliar nutrients concentration. CO{sub 2} enrichment reduced foliar nitrogen and increased the concentration of magnesium; whereas nitrogen fertilization had opposite effects on leaf nitrogen and magnesium concentrations. Moreover, the interaction between elevated CO{sub 2} and N fertilization amplified some element unbalances such ...

International Nuclear Information System (INIS)

A series of #alpha#-sialon (#alpha#') compositions containing mixed stabilising cations were prepared, by introducing additional CaO to a basic Sm #alpha#-sialon compositions. The thermal stability of these Sm-Ca-containing #alpha#-sialon phases was investigated using XRD, SEM and EDXS techniques. It was found that the addition of calcium into the Sm #alpha#-sialon systems greatly improved the stability of the #alpha#-sialon phases. Calcium was found to be incorporated into the #alpha#-sialon structure, coexistent with the samarium, and partitioning of the calcium and samarium was observed between the #alpha#' phase and grain boundary phases. This indicates a technique which may be used to improve the thermal stability of the #alpha#' phase while maintaining good refractory phases at the sialon grain boundaries.

International Nuclear Information System (INIS)

A study was made on extraction of a series of lithium and calcium salts by monopodands L with common formula R-C_6H_4-O-(CH_2CH_2O)_n-C_6H_4-R, where R - CH_2P(O)Ph_2, n 1-3. Extraction-chromatographic separation of lithium and calcium isotopes in systems of metal aquacomplex-solvatocomplex with L in organic phase was conducted. It was established that separation coefficients of "6Li/"7Li isotopes ranged between 1.003 #+-#0.001 and 1.017 #+-#0.002 at the maximal separation degree equal to 1.60. Separation of "4"0Ca/"4"4Ca isotopes was not fixed. 12 refs., 4 figs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

The objective of materials research is the development of economical, safe and efficient synthesis routes that lead to the formation of a photocatalyst which is able to overcome performance problems related to particle size, crystallinity, or low surface area. Here, we report high-quality functional nanoparticles of calcium bismuth mixed oxide with 15nm nominal size corresponding to a specific surface area of 41m^2/g which were produced by single-step flame spray synthesis (FSS). The high temperature of the flame afforded creation of oxygen vacancies which were quantified by near edge X-ray absorption fine structure (NEXAFS) spectra. These two parameters, developed active surface area and created in the flame oxygen vacancies, allowed to enhance the photocatalytic activity of calcium bismu...

Energy Technology Data Exchange (ETDEWEB)

To examine the hormonal regulation of the ATP-dependent Ca{sup 2+} pump in the kidneys, the ATP-dependent Ca{sup 2+} uptake by the basolateral membrane vesicles in the renal cortex was measured using radioactive calcium ({sup 45}Ca{sup 2+}) in rats with vitamin D deficiency or rats undergoing thyroparathyroidectomy. The V{sub max} of the Ca{sup 2+} pump activity was increased not only by administering calcitriol, but also by normalizing the serum calcium level in vitamin D-deficient rats. PTH suppressed the Ca{sup 2+} pump activity in normocalcemic vitamin D-deficient rats. Thyroparathyroidectomy did not affect the Ca{sup 2+} pump activity in the kidneys of normal rats. It was concluded that the ATP-dependent Ca{sup 2+} pump activity was depressed by secondary hyperparathyroidism in vitamin D-deficient rats. (author).

International Nuclear Information System (INIS)

This paper describes stable strontium as composed of four stable isotopes ( Sr 88, Sr 87, Sr 86, and Sr 84), of which Sr 88 contributes more than 82% to its composition. Strontium exists in three crystalline, plymorphic forms; face-centered cubic alpha form, hexagonal beta form and body-centered cubic gamma form. Strontium occupies in many physicochemical aspects an intermediate position between calcium and barium, as does the solubility of strontium salts. As a result of its oxidation potential, strontium readily forms oxides, halides, and sulfide. The author proposes that the slight discrimination against strontium incorporation into bony tissues may be due to the difference in ionic potential (14%) between strontium and calcium. Ionic potential is an indicator of the strength of ionic bonds: strontium has a smaller ratio of ionic charge to ionic radius when compared with calcium.

International Nuclear Information System (INIS)

Research highlights: ? Reports a high protection system for the alloy in corrosive environment. ? Describes an interfacial process with self-healing properties. ? Reports the influence of substrate pre-treatment in the coating performance. - Abstract: In this paper the interface of poly(vinylidene fluoride) coatings prepared by the dip coating method and HF-treated AZ31 magnesium alloy was evaluated. The best performance of this system in corrosion tests compared to ground, as-received and acetic acid cleaned substrates is related to an acid-base interaction at the interface and to interfacial reactions which resulted in a self-healing process. The protectiveness of the samples was investigated using impedance and immersion tests while the coating morphology and interface stability were investigated by scanning electron microscopy, X-ray photoelectron spectroscopy and adhesion tests.

Energy Technology Data Exchange (ETDEWEB)

AZ31 magnesium alloy was friction-welded to AM60 and the microstructures and the friction welding process were studied. The microstructures changed near the weld interface. The AZ31 was refined to a grain size of several {mu}m near the weld interface. The nucleation occurred in the shear bands that were introduced during the welding process. On the other hand, the eutectic structure was deformed and the lamellar structure which was composed of {alpha}-Mg and Mg{sub 17}Al{sub 12} was formed near the weld interface in AM60 alloy. In the friction process, the adhesion and peel off occurred alternately between AZ31 and AM60. Eventually, bonding was completed during upset process. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The development of a twinned microstructure in hexagonal close-packed rolled magnesium compressed in the in-plane direction has been monitored in situ with neutron diffraction. The continuous conversion of the parent to daughter microstructure is tracked through the variation of diffraction peak intensities corresponding to each. Approximately 80% of the parent microstructure twins by 8% compression. Elastic lattice strain measurements indicate that the stress in the newly formed twins (daughters) is relaxed relative to the stress field in the surrounding matrix. However, since the daughters are in a plastically 'hard' deformation orientation, they quickly accumulate elastic strain as surrounding grains deform plastically. Polycrystal modeling of the deformation process provides insight about the crystallographic deformation mechanism involved.

Energy Technology Data Exchange (ETDEWEB)

Grain refinement in AZ31 magnesium alloy has been attempted by hot-rolling and annealing process. Specimens were solution heat treated at 673 K for 36 ks, then hot-rolled at 423-773 K with total reduction of 20-80% by multi pass process. The rolled specimens were annealed at 473-673 K for 3.6 ks. Grain sizes after the solution heat treatment were about 20 to 150 {mu}m. After hot-rolling at 573 K and annealing at 473 K, grain sizes decreased into about 5 to 10 {mu}m. Suppression of grain growth by pinning due to precipitates was observed by transmission electron microscopic observations. (orig.)

UK PubMed Central (United Kingdom)

SUMMARYIn voltage-gated sodium, potassium, and calcium channels the functions of ion conduction and voltage sensing are performed by two distinct structural units: the pore domain...Full Text Available

UK PubMed Central (United Kingdom)

Dominant mutations in sarcomere protein genes cause hypertrophic cardiomyopathy, an inherited human disorder with increased ventricular wall thickness, myocyte hypertrophy, and disarray. To understand...Full Text Available

UK PubMed Central (United Kingdom)

Secondary caries and restoration fracture remain the two most common problems in restorative dentistry. Release of fluoride ions (F) could be a substantial benefit because F could enrich neighboring...Full Text Available

UK PubMed Central (United Kingdom)

The transport of serine into tobacco (Nicotiana tabacum L. var. Xanthi) cells grown in liquid medium was studied. Serine transport was maximal below pH 4.0. A time-dependent stimulation...Full Text Available

UK PubMed Central (United Kingdom)

The H⁺-translocating inorganic pyrophosphatase (H⁺-PPase) associated with vesicles of the vacuolar membrane (tonoplast) isolated from beet (Beta vulgaris L.) is...Full Text Available

UK PubMed Central (United Kingdom)

Feedback controls of estrogen in LHRH-1 neurons play a pivotal role in reproductive function. However, the mechanism of estrogen action in LHRH-1 neurons is still unclear. In the present study, the...Full Text Available

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence analysis was used for the determination of iron, calcium, potassium, copper, manganese and zinc in waste water from the production process of citric acid. (author).

Energy Technology Data Exchange (ETDEWEB)

A process is given for the removal of sulfur oxides from exhaust gases by absorbing with a slurry of red mud containing calcium ion which comprises the steps of: (1) contacting an exhaust gas containing sulfur oxides of not higher than about 100/sup 0/ C with a slurry of red mud containing calcium ion led from the next step (2) to take up sulfur oxides in the gas until ph of the slurry becomes in the range of 4.3 to less than 6 while maintaining the molar fraction of SO/sub 4/-- to total SO/sub 2/ in the slurry within the said pH range at 0.05 to 0.7; and then, (2) contacting the treated gas with a fresh slurry of red mud containing calcium ion to further take up sulfur oxides in the gas while maintaining the concentration of NaHSO/sub 3/ in the slurry at not more than about 8 g/l.

UK PubMed Central (United Kingdom)

Some laboratory experiments have suggested that power-frequency electric and magnetic fields (EMF) may be capable of influencing calcium efflux from cell membranes, pineal function, and circadian rhythms....Full Text Available

UK PubMed Central (United Kingdom)

Epifluorescence images of Ca2+ transients elicited by electrical stimulation of single skeletal muscle fibers were studied with fast imaging techniques that take advantage of the large fluorescence...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Taiheiyo coal deashed using acid treatment and loaded with potassium or calcium was hydro-cracked under gaseous phase to discuss effects of these metals on liquefaction reaction. In addition, the loaded coal was added with red mud catalyst to examine effects of the addition. The loaded potassium has a softening power, and particularly the potassium adsorbed into surface and micropores in the coal decomposes selectively HI-BS and BI-PS and generates gas and HS. On the other hand, potassium deposited on coal surface promotes direct gas production from the coal. Irrespective of its loading modes, calcium has a catalytic nature to produce HI-BS selectively. Calcium also acts to impede decomposition of HI-BS into HS. Adding red mud catalyst to potassium loaded coal increases the inversion rate and the liquefaction yield, and most of the increase is accounted for by HI -BS, and BI-PS. When red mud catalyst is added to ...

UK PubMed Central (United Kingdom)

The amount of phosphorus contained in food as food additives is currently increasing and a high intake of phosphorus can cause various diseases. To determine the effects of a prolonged high phosphorus...Full Text Available

UK PubMed Central (United Kingdom)

Human Factor VIII/von Willebrand factor, purified by calcium citrate-cellulose chromatography and 4% agarose gel filtration was subjected to sodium dodecyl sulfate gel electrophoresis on gels containing...Full Text Available

DEFF Research Database (Denmark)

Citrate is an important naturally occurring inhibitor of calcium stone formation in urine. Urinary citrate excretion was examined in 43 consecutive patients with recurrent idiopathic calcium nephrolithiasis and in 50 normal controls by a specific enzymatic technique. Hypocitraturia (<1.6 mmol/24h) was found in 14 (33%) stone formers compared to 6 (12%) normal controls (p = 0.03). Citrate excretion expressed as citrate-creatinine ratio in 24 hour urine samples was significantly lower in the stone formers than in the healthy controls (p = 0.03), and significantly lower in healthy men, compared to healthy females (p = 0.006). There was a great variability in urinary citrate levels in both groups, and a considerable overlap in the urinary citrate excretion between normal subjects and stone formers. Factors other than urinary citrate excretion must therefore be of importance in the pathophysiology of calcium stone formation. ...

UK PubMed Central (United Kingdom)

Benzodiazepine withdrawal anxiety is associated with potentiation of α-amino-3-hydroxy-5-methyl-4-isoxazolepropionate receptor (AMPAR) currents in hippocampal CA1 pyramidal...Full Text Available

UK PubMed Central (United Kingdom)

Stomatal movements depend on both ion influx and efflux; attainment of steady state apertures reflects modulation of either or both processes. The role of Ca²⁺ in those two processes was...Full Text Available

UK PubMed Central (United Kingdom)

Amyloid proteins constitute a chemically heterogeneous group of proteins, which share some biophysical and biological characteristics, the principal of which are the high propensity to acquire an incorrect...Full Text Available

International Science & Technology Center (ISTC)

Realization of Pharmacological Tests, Development of the Specifications and Technical Documentation and Registration in the Russian Federation of Medical Products as Soluble Tablets of Acetylsalicylic Acid/Calcium Carbonate in Two Dosages Intended for use as Medical Products Smoothing, Febrifugal and Antiaggregation Action and Development of Technology of Tableting the Above-Stated Preparations

DEFF Research Database (Denmark)

The aim of the present study was to test a mathematical model of the biochemical processes in the parathyroid glands responsible for the secretion of parathyroid hormone resulting from extracellular calcium reduction. A double exponential curve described the parathyroid hormone secretion induced by rapid lowering of blood-ionized calcium in humans with normal as well as abnormal parathyroid tissue. Our data show that it was possible to establish a simple mathematical model of the parathyroid hormone response to blood-ionized calcium lowering, sufficient to fit experimental data obtained from patients with abnormal and normal parathyroid tissue. The fitted parameters showed no significant differences between patients with insulin-dependent diabetes mellitus and controls. In primary hyperparathyroidism, the parathyroid hormone production and steady-state transport across the cell membrane were increased, probably due to the ...

Science.gov (United States)

isotherme, dans un courant d'azote ou sous vide entretenu. I t. Comptes Rendus Scientific Academy, Paris, Vol. 265 pyrolyse du carbonate de calcium, ...

Science.gov (United States)

The parathyroid endocrine glands, usually four in number and about the size of a split pea, lie on either side of the posterior aspect of the thyroid gland. Occasionally one or more of these structures are found in an aberrant position in the neck or even in the superior mediastinum. The parathyroid secretion, parathormone, regulates the level of serum calcium within sharply defined limits. Lack of parathormone, with lowering of the serum calcium, results in hyper-irritability of skeletal muscle, the clinical condition known as tetany. This is encountered following inadvertent removal or bruising of the parathyroid glands at thyroidectomy. PMID:21488463

Energy Technology Data Exchange (ETDEWEB)

Calcium sulfate dihydrate in large crystal form is produced by maintaining the circulation of the lime containing scrubbing solution in the desulfurization scrubbing of flue gases from a power plant boiler so that it has a residence time of 5 to 25 hours, preferably 15 hours. The crystals are moved by passing a portion of the recirculation through a thinner in which a sludge containing crystals with a mean particle size of which 90% is in excess of 100 microns is removed. This product can be dewatered and treated with sulfuric acid and steam to convert it to the alpha semihydrate and is free from sulfite.

Energy Technology Data Exchange (ETDEWEB)

A heat storage compostion comprises sodium sulfate decahydrate as main component, a supercooling inhibitor, and a solid-liquid separation inhibitor. The composition is characterized in that hydraulic calcium sulfate and/or calcium sulfate dihydrate is contained as the solid-liquid separation inhibitor in an amount of 2-15 wt% base on the whole weight of the composition, whereby the solid-liquid separation, i.e. the sedimentation of the anhydrous sodium sulfate during the phase transition, is effectively prevented and the long-term stability is improved. The long-term stabilty of the composition can be more improved by addition of a silcia series of thickener.

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and ...

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl solution with a ...

International Nuclear Information System (INIS)

Many hormones elicit effects on target cells by stimulating the enzyme phospholipase-C, which catalyzes the hydrolysis of phosphoinositides to the intracellular second messengers diacylglycerol and inositol phosphates. The present study examined the roles of FSH and guanine nucleotide-binding proteins (G-proteins) in regulating the hydrolysis of phosphoinositides in Sertoli cells. Sertoli cell cultures prepared from 16- to 18-day-old rats were incubated for 24 h with myo-[2-3H] inositol to label endogenous phospholipids. Treatment of cells from 0.5-20 min with preparations of ovine FSH ranging in potency from 1-60 times that of NIH FSH S1 did not affect accumulation of inositol phosphates. Levels of total [3H]inositol phosphates [[3H]inositol mono-, di-, and triphosphates (IP, IP2, and IP3)] in FSH-treated cultures was 75-120% the levels in control cultures over the various time intervals studied. Addition of testosterone ...

Energy Technology Data Exchange (ETDEWEB)

Fungi such as Aspergillus niger and Mucor rouxii are capable of removing heavy metals from aqueous solutions. The role various functional groups play in the cell wall of M. rouxii in metal biosorption of lead, cadmium, nickel and zinc was investigated in this paper. The biomass was chemically treated to modify the functional carboxyl, amino and phosphate groups. These modifications were examined by means of infrared spectroscopy. It was found that an esterification of the carboxyl groups and phosphate and a methylation of the amine groups significantly decreased the biosorption of the heavy metals studied. Thus, the carboxylate, amine and phosphate groups were recognized as important in the biosorption of metal ions by M. rouxii biomass. The role the lipids fraction play was not significant. The study showed that Na, K, Ca and Mg ions were released from the biomass after biosorption of Pb,Cd,Ni and Zn, indicating that ion ...

Energy Technology Data Exchange (ETDEWEB)

A room-temperature process for stabilizing mineral waste streams has been developed, based on acid-base reaction between MgO and H3PO4 or acid phosphate solution. The resulting waste form sets into a hard ceramic in a few hours. In this way, various alumina industry wastes, such as red mud and treated potliner waste, can be solidified into ceramics which can be used as structural materials in waste management and construction industry. Red mud ceramics made by this process were low-porosity materials ({approx}2 vol%) with a compression strength equal to portland cement concrete (4944 psi). Bonding mechanism appears to be result of reactions of boehmite, goethite, and bayerite with the acid solution, and also encapsulation of red mud particles in Mg phosphate matrix. Possible applications include liners for ponds and thickned tailings disposal, dikes for waste ponds, and grouts. Compatability problems arising at the interface of the liner and ...

Energy Technology Data Exchange (ETDEWEB)

Separation of the bulk soluble chemical salts from the insoluble metal hydroxides and radionuclides is central to the strategy of disposing Hanford tank waste. Sludge washing and caustic leaching have been selected as the primary methods for processing the 230 million L (61,000,000 gal) of Hanford tank waste. These processes are very similar to those selected for processing waste at the West Valley Site in New York and the Savannah River Site in South Carolina. The purpose of sludge washing is to dissolve and remove the soluble salts in the waste. Leaching of the insoluble solids with caustic will be used to dissolve aluminum hydroxide and chromium hydroxide, and convert insoluble bismuth phosphate to soluble phosphate. The waste will be separated into a high-level solids fraction and a liquid fraction that can be disposed of as low-level waste after cesium removal. The washing and leaching operations involve batchwise mixing, settling, and ...

Science.gov (United States)

Green crab (Scylla serrata) alkaline phosphatase (EC 3.1.3.1) is a metalloenzyme, which catalyzes the nonspecific hydrolysis of phosphate monoesters. The kinetics of inhibition of the enzyme by sodium (2, 2'-bipyridine) oxodiperoxovanadate, pV(bipy), has been studied. The time course of the hydrolysis of p-nitrophenyl-phosphate catalyzed by the enzyme in the presence of different pV(bipy) concentrations showed that at each pV(bipy) concentration, the rate decreased with increasing time until a straight line was approached, the straight line slopes are the same for all concentrations. The results suggest that the inhibition of the enzyme by pV(bipy) is a slow, reversible reaction with fractional remaining activity. The microscopic rate constants are determined for the reaction of inhibitor with the enzyme. PMID:10691182

Energy Technology Data Exchange (ETDEWEB)

As a new high-voltage cathode candidate for post 4V cathodes, ordered-olivine LiCoPO{sub 4} and fluoride phosphate, Li{sub 2}CoPO{sub 4}F were synthesized by solid-state reaction. Their structures were identified by neutron diffraction. The 5V discharge profiles were demonstrated using coin-type cells. Two important issues for commercial use, metal dissolution and oxygen release at elevated temperatures, were also tested with an atomic absorption spectrophotometer and differential scanning calorimeter, respectively. (author)

Energy Technology Data Exchange (ETDEWEB)

The aims of the present work were to investigate possible compatibility between sodium zirconium phosphate (NZP) and Synroc titanate phases, to prepare NZP-based waste forms by hot-pressing rather than sintering, and to investigate the incorporation in NZP of (a) Cs/Sr as simulated heat-generating nuclides; (b) simulated actinides; and (c) simulated Purex waste. The NZP samples were prepared by methods similar to those used for Synroc. The precursor NZP phase was formed from tetrabutyl zirconate Zr(OC{sub 4}H{sub 9}){sub 4}, sodium nitrate, and 85% orthophosphoric acid. Simulated waste nitrate solutions were then mixed with the liquid precursor. After stir drying of the precursor, calcination was carried out at 700{degree}C to remove nitrates and organics.

Science.gov (United States)

High performance sorbents for flue gas desulfurization can be synthesized by hydration of coal fly ash, calcium sulfate, and calcium oxide. In general, higher desulfurization activity correlates with higher sorbent surface area. Consequently, a major aim in sorbent synthesis is to maximize the sorbent surface area by optimizing the hydration conditions. This work presents an integrated modeling and optimization approach to sorbent synthesis based on statistical experimental design and two artificial intelligence techniques: neural network and genetic algorithm. In the first step of the approach, the main and interactive effects of three hydration variables on sorbent surface area were evaluated using a full factorial design. The hydration variables of interest to this study were hydration time, amount of coal fly ash, and amount of calcium sulfate and the levels investigated were 4-32 h, 5-15 g, and 0-12 g, respectively. In ...

Energy Technology Data Exchange (ETDEWEB)

Red light stimulates germination in the spores of Onoclea sensibilis L. Phytochrome is confirmed to be the photoreceptor pigment in the germination response by demonstrating red-far-red photoreversibility. External Ca/sup 2 +/ is required for this response with a threshold at a submicromolar concentration. Red light stimulates an increase in the total concentration of intracellular calcium in the spores as determined by atomic absorption spectroscopy. Subsequent exposure to far-red light inhibits the red light-induced increase in intracellular calcium. The majority of the increase occurs 5 minutes after the onset of irradiation. The calcium-antagonist, La/sup 3 +/ inhibits both germination and the red light-induced increase in intracellular calcium. Using /sup 31/P-nuclear magnetic resonance spectroscopy, the author tested the hypothesis that a sustained increase in intracellular pH contributes to the ...

UK PubMed Central (United Kingdom)

Brassica napus is an allotetraploid (AACC) formed from the fusion of two diploid progenitors, Brassica rapa (AA) and Brassica oleracea...Full Text Available

Environmental Research Database

DescriptionThis project has two independent aims: (1) to investigate the use of struvite as an alternative to chemical P fertilisers and (2) to develop an oligonucleotide microarray to monitor the P status of the potato crop. The UK horticultural and agricultural industries rely on large inputs of phosphate (P) fertilisers to maintain crop yields and quality. However, the use of non-renewable, chemical P fertilisers is unsustainable, and the alternatives to chemical P-fertilisers must be identified as an [continued...

Energy Technology Data Exchange (ETDEWEB)

Calorimetry testing of Tri-n-butyl phosphate (TBP) saturated with strong nitric acid was performed to determine the relationship between vent size and pressure buildup in the event of a runaway reaction. These experiments show that runaway can occur in an open system, but that even when runaway is induced in the TBP/HN0{sub 3} system, dangerous pressure buildup will be prevented with practical vent size.

Energy Technology Data Exchange (ETDEWEB)

A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with an anion such as a dihydrogen phosphate anion or a dihydrogen phosphite anion and additionally with an ammonium salt other than a salt of an inorganic acid of phosphorus. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.

International Nuclear Information System (INIS)

The annual production of phosphate rock, on the order of about 30-40 million tons yearly, represents several million pounds of uranium. The present invention provides a process of purifying uranium tetrafluoride hydrate to produce a uranium (VI) peroxide product meeting 'yellow cake' standards using a double precipitation procedure. A fluoride complexing agent is used in the precipitation.

UK PubMed Central (United Kingdom)

The bifunctional rat liver enzyme 6-phosphofructo-2-kinase/fructose-2,6-bisphosphatase (ATP:D-fructose-6-phosphate 2-phosphotransferase/D-fructose-2,6-bisphosphate 2-phosphohydrolase, EC 2.7.1.105/EC...Full Text Available