WorldWideScience
2

Thermoluminescence studies in cerium doped NaCl crystals  

International Nuclear Information System (INIS)

Cerium is known to enter substitutionally in trivalent state when doped in alkali halides. Cerium doped NaCl crystals exhibit greatly enhanced thermoluminescence output upon X-irradiation at RT, the intensity of emission being about 10 times that in undoped crystals for similar dosage of irradiation. The cerium doped crystals give upon X-irradiation a very intense glow peak at 145degC with shoulders at 120degC and 210degC. Upon partially bleaching the crystal with F-light, the peak at 120degC becomes prominent probably due to faster bleaching of the glow at 145degC. From further optical bleaching studies, it is concluded that the glow peak at around 120degC is due to cerium centres in the irradiated crystal and the 145degC peak due to F centres. This F centre emission occurs at lower temperature, compared to that in the undoped crystals ...

3

Effects of manganese doping on properties of sol-gel derived biphasic calcium phosphate ceramics  

British Library Electronic Table of Contents (United Kingdom)

We have investigated the effect of manganese (Mn) doping on properties of nanosized biphasic calcium phosphate powders and their dense bodies. Manganese levels of 0.6, 1.3, 1.9, 4.3, 7.0 and 11.9at.% were successfully incorporated into biphasic calcium phosphate via a sol-gel route. The prepared powders were calcined at temperatures of 500-1200^oC. The X-ray diffraction analysis revealed that a mix phase comprising of hydroxyapatite and @b-tricalcium phosphate were present, however the content of each phases in the structure was affected by the Mn content. The studies found that the largest portion of @b-tricalcium phosphate was detected at 4.3at.% Mn doping. The incorporation of Mn has also greatly increased the crystallinity of the biphasic calcium phosphate powder due to progressive den...

2011-01-01

4

Phase diagrams  

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

5

Session 6: Redox Behavior of Cerium-Zirconium-Bismuth Mixed Oxides  

Energy Technology Data Exchange (ETDEWEB)

The CeO{sub 2}-ZrO{sub 2}-Bi{sub 2}O{sub 3} samples with different bismuth content were prepared in this study. By the doping of Bi{sub 2}O{sub 3} into the lattice, TPR profiles of the CeO{sub 2}-ZrO{sub 2} shifted to lower temperatures and oxygen storage capacity increased remarkably. It is concluded that the reason for such a behavior is probably due to both the formation of oxygen vacancies which enhance the oxygen mobility and the simultaneous reduction of Ce{sup 4+} and Bi{sup 3+} in the mixed oxides. (authors)

2004-07-01

6

Structure of Ce-doped Bi/sub 2/(MoO/sub 4/)/sub 3/ as determined by neutron profile refinement  

Energy Technology Data Exchange (ETDEWEB)

The structure of Bi/sub 1.8/Ce/sub 0.2/(MoO/sub 4/)/sub 3/ has been refined with powder neutron diffraction data by the Rietveld method. The structure can be derived by severely distorting the scheelite structure (AMO/sub 4/) and is perhaps better written A/sub (2/3)/phi/sub (1/3)/MO/sub 4/, where phi = cation vacancy. Of the two bismuth atom sites, cerium preferentially occupies the more symmetric of the two (Bi(2) in the structure) with some cerium found in the scheelite subcell vacancies also. This site preference is understood by examining the symmetries of the two Bi sites. Crystal data: monoclinic, space group P2/sub 1//c, Z = 4, a = 7.697(2), b = 11.535(3), c = 11.944(3), ..beta.. = 115.19.

1984-05-01

7

Nanocrystalline doped cerium oxide as a catalyst for SO{sub 2} reduction by CO  

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline processing by inert gas condensation has the inherent advantages of generating: (1) high surface area nanoclusters, (2) non-stoichiometric oxides, and (3) high dispersions of dopants. This approach is exploited in the synthesis of fluorite-structured catalysts for SO{sub 2} reduction by CO. Nanocrystalline CeO{sub 2{minus}x}, La-doped CeO{sub 2{minus}x}, and Cu-doped CeO{sub 2{minus}x} were produced by magnetron sputtering from a pure or mixed metal target, followed by controlled oxidation of the metallic clusters. The as-prepared doped and undoped nanocrystalline CeO{sub 2{minus}x} materials were found to be excellent catalysts for complete SO{sub 2} conversion to elemental sulfur. Undoped nanocrystalline CeO{sub 2{minus}x} enabled light-off at 460 C, a temperature {approximately} 120 C lower than that over polycrystalline CeO{sub 2}, which is a novel effective catalyst itself. The high catalytic activity ...

1994-12-31

8

Jump in the air gasification rate of potassium-doped cellulosic chars  

Energy Technology Data Exchange (ETDEWEB)

Chars prepared from potassium-exchanged carboxy methyl cellulose at several heat treatment temperatures (HTTs) were gasified in air isothermally at selected gasification temperatures (GTs) in the range 633-893 K to investigate the catalytic effectiveness of potassium species. The chars displayed a noticeable jump in gasification rate at a particular gasification temperature (called jump temperature, T{sub j}). The magnitude of jump was much less than that reported for copper and nickel catalysis, but comparable with that for calcium catalysis. Increase in HTT caused a decrease in the jump temperature of chars in contrast with the increase observed in copper, nickel and calcium catalysis; also the magnitude of jump did not decrease, but remained unaltered, on increasing HTT. The different behavior of potassium catalysis is correlated to a change in the chemical state of potassium at higher HTT. The results reveal the dependence of jump ...

2010-12-15

9

Trace metal characterization of the U-Al matrix by atomic spectroscopy  

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples ...

10

Study on pyrolysing behavior of NiO-SDC composite particles prepared by spray pyrolysis technique  

Energy Technology Data Exchange (ETDEWEB)

The NiO-samaria doped ceria (SDC) composite powders were prepared by spray pyrolysis technique at temperatures between 400 and 1000 C. The variation of the particle structure was investigated by X-ray diffraction (XRD), X-ray absorption fine structure (XAFS), scanning electron microscope (SEM), and transmission electron microscope (TEM)-energy-dispersive X-ray spectroscopy (EDS). The thermal analysis of raw materials was also carried out. The following facts became clear in this study. Ceria and nickel have been already separated at 400 C. Samaria is amorphous phase below 600 C, and is dissolved in ceria at 600 C or higher. Samaria is distributed uniformly inside the particles before dissolving in ceria. The thermal decomposition temperatures of metal nitrate are: cerium < nickel < samarium. The results of these analyses were explained without contradiction. It was found that it is important to optimize the state of liquid drop ...

2007-03-15

11

Decontamination agent for chemically dissolving radioactive crud and its method  

International Nuclear Information System (INIS)

Purpose: To dissolve iron and nickel as well as chromium simultaneously at one step for cruds partially containing chromium, and obtain high decontaminating factor (decontamination factor). Method: Radioactive cruds formed as corrosion products in nuclear reactor primary coolant circuits are subjected to dissolving treatment by using a decontaminating agent composed of cerium sulfate type solution as the dissolving solution. When the treatment is substantially completed, a reducing agent is added to reduce the residual 4-valent cerium into 3-valent cerium. Those having potential lower than the redox potential of cerium are used as the reducing agent so that cerium is not deposited. This can provide high decontaminating factor while preventing the deposition of cerium. (Takahashi, M.).

1986-05-07

12

Difference in the effects produced by non-radioactive and radioactive calcium  

International Nuclear Information System (INIS)

... aluminum calcium calcium 45 cations citric acid corrosion inhibition radiation

13

Zeolite-supported catalysts. Report for August 1986-November 1987  

Energy Technology Data Exchange (ETDEWEB)

The present paper is a comparative study of the cerium-containing nickel catalysts supported on x- and y-zeolites. In general, the addition of cerium ions caused an increase in the catalytic activity for CO hydrogenation and shifted the product selectivity to high molecular weight hydrocarbons. The degree of the effect of cerium additive depends on the ratio of cerium to nickel contents, the reduction temperature, and the nature of the supporting materials. Catalyst characterization, including volumetric hydrogen chemisorption, temperature programmed reduction/desorption, x-ray diffraction, surface area measurements, in-situ infrared spectroscopy and x-ray photoelectron spectroscopy, was performed in order to interpret the phenomena due to the effects of cerium additives and the support effect on Ni/zeolite catalysts.

1988-01-01

17

Spin-density-wave transition and #mu#SR in the heavy-fermion Ce(Ru, T)_2Si_2, T = Rh, Pd  

International Nuclear Information System (INIS)

... 900526-11-8 277 p. MATERIALS SCIENCE antiferromagnetic materials cerium

1999-02-28

18

Selective radiochemical separation for indium determination at ppb levels in ion-implanted semiconductor-grade silicon  

Energy Technology Data Exchange (ETDEWEB)

A specific radiochemical procedure for indium determination in semiconductor-grade silicon, using an inorganic ion exchanger (cerium oxalate) is proposed.

1982-12-23

20

Augmented behavioral response and enhanced synaptosomal calcium transport induced by repeated cocaine administration are decreased by calcium channel blockers  

UK PubMed Central (United Kingdom)

Recent studies suggest that calcium influx via L-type calcium channels is necessary for psychostimulant-induced behavioral sensitization. In addition, chronic amphetamine upregulates subtype...Full Text Available

2007-07-26

21

Cerium moment collapse in ternary silicides CePd[sub 2[minus][ital x  

Energy Technology Data Exchange (ETDEWEB)

Cerium [ital L][sub 3] XANES (x-ray-absorption near-edge-structure) spectra were analyzed to separate Ce moment contributions and mixed valence (MV) in complex magnetic silicides CePd[sub 2[minus][ital x

1994-05-01

22

Rare Earth Doped Yttrium Aluminum Garnet (YAG ... - GLTRS - NASA  

Science.gov (United States)

films and cylinders of rare earth doped yttrium aluminum garnets. ... We knew that yttrium aluminum garnet (YAG) could be doped with ...

23

Selective excitation study of Yb{sup 3+} in GdCa{sub 4}O(BO{sub 3}){sub 3} and YCa{sub 4}O(BO{sub 3}){sub 3}  

Energy Technology Data Exchange (ETDEWEB)

The Yb{sup 3+}-doped non-linear rare-earth calcium oxoborate crystals GdCa{sub 4}O (BO{sub 3}){sub 3} (GdCOB) and YCa{sub 4}O(BO{sub 3}){sub 3} (YCOB) were investigated by low-temperature absorption and selective excitation spectroscopy. The selective excitation and emission spectra revealed the spectral features of the main Yb{sup 3+} centre and the principal minority one in both crystals. The energy level schemes for these centres in both hosts, as well as structural assignments, were proposed. It was established that the minority centre, which represents about 10% of the total intensity and was assigned to Yb{sup 3+} in a Ca{sup 2+} site, is not a trap but an energy donor for the main centre. Common features of and differences between the vibronic structure of the two centres in GdCOB and YCOB are discussed. The existence of additional features in YCOB:Yb spectra is pointed out. (author)

2002-02-11

24

Selective excitation study of Yb"3"+ in GdCa_4O(BO_3)_3 and YCa_4O(BO_3)_3  

International Nuclear Information System (INIS)

The Yb"3"+-doped non-linear rare-earth calcium oxoborate crystals GdCa_4O (BO_3)_3 (GdCOB) and YCa_4O(BO_3)_3 (YCOB) were investigated by low-temperature absorption and selective excitation spectroscopy. The selective excitation and emission spectra revealed the spectral features of the main Yb"3"+ centre and the principal minority one in both crystals. The energy level schemes for these centres in both hosts, as well as structural assignments, were proposed. It was established that the minority centre, which represents about 10% of the total intensity and was assigned to Yb"3"+ in a Ca"2"+ site, is not a trap but an energy donor for the main centre. Common features of and differences between the vibronic structure of the two centres in GdCOB and YCOB are discussed. The existence of additional features in YCOB:Yb spectra is pointed out. (author)

2002-02-11

25

Semi-empirical simulation of thermoluminescent response under different filter geometries; Simulacao semi-empirica da resposta termoluminescente sob diferentes geometrias de filtro  

Energy Technology Data Exchange (ETDEWEB)

Many thermoluminescent materials has been developed and used for photon personal dosimetry but no one has all desired characteristics alone. These characteristics include robustness, high sensitivity, energy photon independence, large range of photon energy detection, good reproducibility, small fading and simple glow curve with peaks above 150 deg C. Calcium Sulfate Dysprosium doped (CaSO{sub 4}:Dy) phosphor Thermoluminescent Dosimeter (TLD) has been used by many laboratories, mainly in Brazil and India. Another interesting phosphor is Calcium Fluoride (CaF{sub 2}). These phosphor advantages begin to be more required and its disadvantages have became more apparent, in a global market more and more competitive. These phosphors are used in environmental and area monitoring, once they present more sensibility than other phosphors, like LiF:Mg. Theirs mainly disadvantage is a strong energetic dependence response, which must be ...

2006-07-01

26

Carbon tetrachloride-induced release of calcium from isolated hepatocytes  

International Nuclear Information System (INIS)

Studies have shown that CCl_4 administration to rats inhibits endoplasmic reticulum calcium pump activity and reduces the amount of calcium associated with subsequently isolated microsomal subcellular fractions. This report confirms that exposure of isolated hepatocytes to CCl_4 rapidly produces these effects in isolated parenchymal cells and demonstrates that when isolated hepacytes are exposed to CCl_4 calcium is rapidly released from cells. This release can be detected with a calcium ion-selective electrode when cells are incubated in a medium with low extracellular calcium. Calcium released from an intracellular pool(s) may initiate hepatotoxic changes in liver. (author).

27

Microstructure and emission properties of nanometer Ce-W material  

International Nuclear Information System (INIS)

Nanometer Ce-W composite materials have been prepared by the method of freeze-drying. Microstructure and surface properties of materials were investigated by SEM and 'in situ' AES and emission characteristics have been determined. It is found that the nanometer materials have relatively small crystal particles with average dimensions in the order of 50 nm. Due to the results of matrix analysis, the cerium in the materials is uniformly distributed on submicron scale, which proves that the diffusion ability of cerium has been increased. Under high temperature, the active layer on the surface thickens simultaneously with the increase of cerium and oxygen. As a result, nanometer Ce-W materials exhibit excellent emission characteristics compared with those of micron-sized Ce-W materials.

2007-07-12

28

Catalyst and method for reduction of nitrogen oxides  

Energy Technology Data Exchange (ETDEWEB)

A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).

2008-08-19

29

Catalyst and method for reduction of nitrogen oxides  

Energy Technology Data Exchange (ETDEWEB)

A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).

2008-05-27

30

Tin doping in spray pyrolysed indium sulfide thin films for solar cell applications  

British Library Electronic Table of Contents (United Kingdom)

This paper presents studies carried out on tin-doped indium sulfide films prepared using Chemical Spray Pyrolysis (CSP) technique. Effect of both in-situ and ex-situ doping were analyzed. Ex-situ doping was done by thermal diffusion, which was realized by annealing Sn/In2S3 bilayer films. In-situ doping was accomplished by introducing Sn into the spray solution by using SnCl45H2O. Interestingly, it was noted that by ex-situ doping, conductivity of the sample enhanced considerably without affecting any of the physical properties such as crystallinity or band gap. Analysis also showed that higher percentage of doping resulted in samples with low crystallinity and negative photosensitivity. In-situ doping resulted in amorphous films. In contrast to ex-situ doping, `in- situ doping' resulted i...

2010-01-01

31

Spatiotemporal intracellular calcium dynamics during cardiac alternans  

UK PubMed Central (United Kingdom)

Cellular calcium transient alternans are beat-to-beat alternations in the peak cytosolic calcium concentration exhibited by cardiac cells during rapid electrical stimulation or under pathological conditions....Full Text Available

2009-09-01

32

Sodium/Calcium Exchangers Selectively Regulate Calcium Signaling in Mouse Taste Receptor Cells  

UK PubMed Central (United Kingdom)

Taste cells use multiple signaling mechanisms to generate appropriate cellular responses to discrete taste stimuli. Some taste stimuli activate G protein coupled receptors (GPCRs) that cause calcium...Full Text Available

2010-07-01

33

Role of plasma membrane calcium ATPase 2 in spinal cord pathology  

UK PubMed Central (United Kingdom)

A number of studies have indicated that plasma membrane calcium ATPases (PMCAs) are expressed in the brain and spinal cord and could play important roles not only in the maintenance of cellular calcium...Full Text Available

2010-05-26

34

Hypertrophy and Heart Failure in Mice Overexpressing the Cardiac Sodium-Calcium Exchanger  

UK PubMed Central (United Kingdom)

Background:The cardiac sodium–calcium exchanger (NCX1) is a key sarcolemmal protein for the maintenance of calcium homeostasis in the heart. Since heart failure...Full Text Available

2007-05-01

35

Demographic, Dietary, and Urinary Factors and 24-h Urinary Calcium Excretion  

UK PubMed Central (United Kingdom)

Background and objectives: Higher urinary calcium is a risk factor for nephrolithiasis. This study delineated associations between demographic, dietary, and urinary factors and 24-h urinary calcium.Design,...Full Text Available

2009-12-01

36

Calcium Requirements and Metabolism in Chinese-American Boys and Girls  

UK PubMed Central (United Kingdom)

Calcium requirements of North American adolescents were set at 1300 mg/day based on data from white girls. Calcium requirements for Asian-American adolescents have not been studied. Using metabolic...Full Text Available

2010-08-01

37

Effect of calcium and phosphorus on the gastrointestinal absorption of /sup 203/Pb in man  

Energy Technology Data Exchange (ETDEWEB)

Calcium and phosphorus were mainly responsible for reducing the gastrointestinal absorption of lead in human subjects. The effect of calcium was greater than phosphorus, and their combined effect was more than additive. Increasing weights of calcium and phosphorus progressively reduced lead absorption. The relationship between absorption and increasing weights could be described by two negative exponentials. These effects could be explained if lead competed with calcium and phosphorus for common transport mechanisms in the gut. Milk was also found to reduce lead absorption. Adding milk to the diet of people with low dietary calcium intake could reduce the possibility of increased absorption of ingested lead.

1983-02-01

38

Refilling Intracellular Calcium Stores  

UK PubMed Central (United Kingdom)

Within the cardiac cell, the movements of calcium ions are tightly regulated by a number of regulatory proteins including pumps, and channels. The sarcoplasmic reticulum (SR) is in large part...Full Text Available

2010-01-01

39

Calcium-Actin Waves and Oscillations of Cellular Membranes  

UK PubMed Central (United Kingdom)

AbstractWe propose a mechanism for the formation of membrane oscillations and traveling waves, which arise due to the coupling between the actin cytoskeleton and the calcium flux through...Full Text Available

2009-09-16

41

Structure and Mechanical Properties of Boron-Doped Cubic ...  

Science.gov (United States)

... by the boron doping in most of the alloys except for Al66Mn9Zr25 + 50 ppm B alloy; permanent deformation at ultimate compressive strength is not ...

52

Advancing Age Alters the Contribution of Calcium Release From Smooth Endoplasmic Reticulum Stores in Superior Cervical Ganglion Cells  

UK PubMed Central (United Kingdom)

In superior cervical ganglion (SCG) neurons calcium-induced calcium release (CICR), mediated by ryanodine receptors (RyRs), contributes to stimulation-evoked intracellular calcium ([Ca2+]i)...Full Text Available

2009-01-01

53

Carbon dioxide absorption mechanisms of sodium added to calcium oxide at high temperatures  

Energy Technology Data Exchange (ETDEWEB)

To apply the CO{sub 2} absorber at about 1000{sup o}C for integrated coal gasification combined cycle (IGCC) furnace, the reactions of calcium oxide and CO{sub 2} at high temperatures was examined. Calcium carbonate reacts with sodium hydrogen carbonate below 200{sup o}C and forms sodium-calcium complex carbonate. The sodium-calcium complex carbonate melts at 813{sup o}C, and the carbon dioxide absorption and discharge reversible reactions of calcium-oxide takes place via liquid at around 1000{sup o}C. Sintering of calcium oxide at high temperature has been successfully avoided by the addition of sodium.

2004-07-01

58

Influence of Dopants on Characteristics of X-Ray Detectors Fabricated from Indium-, Gallium-, and Chlorine-Doped Cadmium Telluride Single Crystals  

Science.gov (United States)

Counting characteristics of X-ray detectors fabricated from indium-doped, gallium-doped, and chlorine-doped CdTe have been investigated. The detectors fabricated from indium-doped and gallium-doped crystals showed radiation-induced polarization, namely, a progressive decrease of count rate with an increase of photon fluence in the high-photon-fluence region, while the detectors fabricated from chlorine-doped crystals did not. Results from current-voltage characteristics of the detectors indicated that the different counting characteristics of these detectors originated from the difference in internal electric fields in each detector.

1995-08-01

59

Heat capacity and magnetic ordering of two cerium sulfides, CeS/sub 1. 393/ and CeS/sub 1. 457/  

Energy Technology Data Exchange (ETDEWEB)

Heat-capacity (0.5--20 K) and magnetic-susceptibility (4--300 K) measurements have been made on two cerium sulfide samples having compositions as CeS/sub 1.393/ and CeS/sub 1.457/. These materials follow the Curie-Weiss law above 100 K, and become ferromagnetically ordered near 6 and 3 K, respectively. Shift of the ordering to higher temperatures under applied magnetic fields is also observed in CeS/sub 1.457/. The estimated effective magnetic moment and entropy associated with the ordering are consistent with the paramagnetic nature of Ce/sup 3 +/ (4f/sup 1/) in a crystalline environment.

1982-08-01

60

Cerium moment collapse in ternary silicides CePd_2_-_xMn_xSi_2 (0#<=#x#<=#2)  

International Nuclear Information System (INIS)

Cerium L_3 XANES (x-ray-absorption near-edge-structure) spectra were analyzed to separate Ce moment contributions and mixed valence (MV) in complex magnetic silicides CePd_2_-_xMn_xSi_2 (0#<=#x#<=#2). The Ce valence mixing does not vary linearly with x, but increases rapidly for x#>=#1.5. The associated moment collapse correlates with pronounced deviations of the unit-cell volume from Vegard law and the onset of structural instability. Reorientation of [001] Mn 3d antiferromagnetic order for x<2 appears to rapidly suppress the weak Ce valence mixing coexisting with antiferromagnetic order in CeMn_2Si_2.

61

The role of calcium ions and calcium channel entry blockers in experimental ischemia-reperfusion-induced liver injury.  

UK PubMed Central (United Kingdom)

Verapamil administered before treatment, but not after treatment, had a beneficial effect on a 90-minute warm ischemia-reperfusion rat liver injury model. The possible activation of proteases converting...Full Text Available

1991-02-01

62

The Functional Role of Calcineurin in Hypertrophy, Regeneration, and Disorders of Skeletal Muscle  

UK PubMed Central (United Kingdom)

Skeletal muscle uses calcium as a second messenger to respond and adapt to environmental stimuli. Elevations in intracellular calcium levels activate calcineurin, a serine/threonine phosphatase, resulting...Full Text Available

2010-01-01

63

Strategies for the uses of lanthanide NMR shift probes in the determination of protein structure in solutio. Application to the EF calcium binding site of carp parvalbumin.  

UK PubMed Central (United Kingdom)

The homologous sequences observed for many calcium binding proteins such as parvalbumin, troponin C, the myosin light chains, and calmodulin has lead to the hypothesis that these proteins have homologous...Full Text Available

1980-10-01

64

Modulation of B-cell endoplasmic reticulum calcium homeostasis by Epstein-Barr virus Latent Membrane Protein-1  

UK PubMed Central (United Kingdom)

BackgroundCalcium signaling plays an important role in B lymphocyte survival and activation, and is critically dependent on the inositol-1,4,5-tris-phosphate-induced...Full Text Available

65

Mapping the Spatiotemporal Dynamics of Calcium Signaling in Cellular Neural Networks Using Optical Flow  

UK PubMed Central (United Kingdom)

An optical flow gradient algorithm was applied to spontaneously forming networks of neurons and glia in culture imaged by fluorescence optical microscopy in order to map functional calcium signaling...Full Text Available

2010-08-01

66

Hair Mercury Negatively Correlates with Calcium Pump Activity in Human Term Newborns and Their Mothers at Delivery  

UK PubMed Central (United Kingdom)

BackgroundCalcium homeostasis is a known target of several environmental toxicants including lead and mercury.ObjectiveOur goal was to determine...Full Text Available

2008-02-01

67

Ethoxylated Bisphenol Dimethacrylate-based Amorphous Calcium Phosphate Composites  

UK PubMed Central (United Kingdom)

Improving the anti-demineralizing/remineralizing and mechanical properties of amorphous calcium phosphate (ACP) composites has been the focus of our recent research. In this study, an ethoxylated...Full Text Available

2006-01-01

68

Effects of calcium supplementation on bone density in healthy children: meta-analysis of randomised controlled trials  

UK PubMed Central (United Kingdom)

Objectives To assess the effectiveness of calcium supplementation for improving bone mineral density in healthy children and to determine if any effect is modified by other factors and...Full Text Available

2006-10-14

69

Detrusor overactivity is associated with downregulation of large-conductance calcium- and voltage-activated potassium channel protein  

UK PubMed Central (United Kingdom)

Large-conductance voltage- and calcium-activated potassium (BK) channels have been shown to play a role in detrusor overactivity (DO). The goal of this study was to determine whether bladder outlet...Full Text Available

2010-06-01

70

Calcium, Vitamin D, VDR Genotypes, and Epigenetic and Genetic Changes in Rectal Tumors  

UK PubMed Central (United Kingdom)

Calcium, vitamin D, exposure to sunshine, and vitamin D receptor (VDR) genotypes have been associated rectal cancer. We used data from 750 rectal tumors and 1,205 population-based...Full Text Available

2010-05-01

71

Calcium - blood test: MedlinePlus Medical Encyclopedia  

Science.gov (United States)

Names Ca+2; Serum calcium; Ca++ References Wysolmerski JJ, Insogna KL. The parathyroid glands, hypercalcemia, and hypocalcemia. In: Goldman L, Ausiello D, eds. Cecil...

2011-08-30

72

A Comparison between Quin-2 and Aequorin as Indicators of Cytoplasmic Calcium Levels in Higher Plant Cell Protoplasts 1  

UK PubMed Central (United Kingdom)

Assessment of the regulation of plant metabolism by the calcium ion requires a knowledge of its intracellular levels and dynamics. Technical problems have prevented direct measurement of the concentration...Full Text Available

1989-06-01

73

17?-estradiol regulation of T-type calcium channels in gonadotropin-releasing hormone neurons  

UK PubMed Central (United Kingdom)

T-type calcium channels are responsible for generating low-threshold spikes that facilitate burst firing and neurotransmitter release in neurons. GnRH neurons exhibit burst firing, but the underlying...Full Text Available

2009-08-26

74

Transfer of chemical elements to breast milk  

International Nuclear Information System (INIS)

The project is intended to yield information on the transfer factors describing the transfer of ingested radionuclides to breast milk for the following elements: antimony, cerium, chromium, cobalt, gallium, lanthanum, molybdenum, niobium, radium, ruthenium, silver, thorium, titanium, and uranium. Those yet unknown or poorly known transfer factors are required in order to be able to develop a reliable model for description and assessment of the transfer of the radionuclides and the possibly resulting hazardous doses to infants, and for subsequent formulation of recommendations for radiological protection of the population. (orig./CB)

1999-08-01

76

Smoke Compositions Based on Phosphorus  

Science.gov (United States)

... Both magnesium and aluminium phosphides are therefore potentially more efficient than either calcium or sodium phosphide. ...

1958-03-01

77

Proceedings of ARO Workshop Biostructures as Composite ...  

Science.gov (United States)

... interactive surfaces and interfaces, and 3) the more complex a ... carbonate or calcium phosphate with a thin interface ... diameter) for nerve prosthesis. ...

1990-03-01

79

Well preflush fluid  

Energy Technology Data Exchange (ETDEWEB)

This patent describes a preflush fluid for preventing lost circulation during the cementing of a well, the fluid consisting essentially of: (a) water; (b) about 10 to about 30 percent by weight of water (% BWOW) cement; (c) about 5 to about 30% BWOW calcium sulfate selected from the group consisting of calcium sulfate hemihydrate, calcium sulfate dihydrate, and mixtures thereof; and (d) an alkali metal-containing quick-hardening accelerator.

1992-01-21

80

Removal of noxious contaminants from gas  

Science.gov (United States)

Gas contaminated with at least one noxious component, such as SO/sub 2/, HF or NOx, is scrubbed with a clear, calcium-containing, initially-basic washing liquid which also comprises the anion of a strong inorganic acid, that of a polybasic carboxylic acid and, optionally, that of a monobasic carboxylic acid. Apparatus is provided for scrubbing the gas, oxidizing produced calcium bisulfite to calcium sulfate, separating out and removing solids, and recirculating clarified liquid for scrubbing contaminated gas.

1980-09-16

81

Calcium fluoride window mounting  

International Nuclear Information System (INIS)

A technique has been developed for joining a large calcium fluoride crystal to a stainless-steel flange by means of a silver transition ring. The process involves both vacuum brazing using a copper-silver alloy and air brazing using silver chloride. This paper describes the procedure used in fabricating a high-vacuum leak-tight calcium fluoride window assembly.

82

Characterization of the product of the thiosulfate process for desulfurization of flue gases  

Energy Technology Data Exchange (ETDEWEB)

X-ray diffraction, infrared spectroscopy, thermal analysis, scanning electron microscopy, and particle size analysis were used to characterize the product of the thiosulfate process. It was found to consist of a mixture of a solid solution of calcium sulfate in calcium sulfite hemihydrate, calcium sulfate dihydrate, and calcium carbonate. Reactions taking place on heating the byproduct were identified in oxidizing and reducing atmospheres. Pure calcium sulfite hemihydrate as well as solid solutions of CaSO[sub 4] in CaSO[sub 3] [center dot] (1/2)H[sub 2]O with different sulfate concentrations were synthesized in the laboratory. Thermal analyses of pure solid solutions proved that the higher the sulfate content, the higher is the dehydration temperature. Accordingly, taking SO[sub 4][sup 2[minus

1994-05-01

83

Strongly enhanced critical current density in MgB{sub 2}/Fe tapes by stearic acid and stearate doping  

Energy Technology Data Exchange (ETDEWEB)

Fe-sheathed MgB{sub 2} tapes with cheap stearic acid, Mg stearate and Zn stearate doping were prepared through the in situ powder-in-tube method. It is found that J{sub c}, H{sub irr} and H{sub c2} were significantly enhanced by doping. Compared to the pure tapes, J{sub c} for all the doped samples was improved by more than an order of magnitude in a high-field regime. At 4.2 K, the transport J{sub c} reached 2.02 x 10{sup 4} A cm{sup -2} at 10 T for the Zn stearate doped tapes and 3.72 x 10{sup 3} A cm{sup -2} at 14 T for the stearic acid doped samples, respectively. Moreover, at 20 K, H{sub irr} for the Zn stearate doped tape achieved 10 T, which is comparable to that of the commercial NbTi at 4.2 K. The improvement of J{sub c}-H properties in doped samples can be attributed to the increase of H{sub c2} resulting from the incorporation of ...

2007-05-15

84

Valence transition and magnetic ordering in Sn doped EuPd/sub 2/Si/sub 2/  

Energy Technology Data Exchange (ETDEWEB)

The sharp, temperature induced, continuous valence transition in EuPd/sub 2/Si/sub 2/ is drastically changed by doping with Sn at the Si site up to 5 at.%. Only a first order valence transition occurs for a 3% Sn doped sample and the 2/sup +/ component which survives the valence transition orders magnetically at 4.2 K. No valence transition at all occurs for a 5% Sn doped sample right up to 1.9 K and magnetic ordering sets in around 30 K.

1983-12-01

86

Structural, optical, photocatalytic and antibacterial activity of zinc oxide and manganese doped zinc oxide nanoparticles  

British Library Electronic Table of Contents (United Kingdom)

Polycrystalline ZnO doped with Mn (5 and 10at%) was prepared by the co-precipitation method. The effect of Mn doping on the photocatalytic, antibacterial activities and the influence of doping concentration on structural, optical properties of nanoparticles were studied. Structural and optical properties of the particles elucidated that the Mn2+ ions have substituted the Zn2+ ions without changing the Wurtzite structure of ZnO. The optical spectra showed a blue shift in the absorbance spectrum with increasing dopant concentration. The photocatalytic activities of ZnO powders were evaluated by measuring the degradation of methylene blue (MB) in water under the UV region. It was found that undoped ZnO bleaches MB much faster than manganese doped ZnO upon its exposure to the U...

2010-01-01

87

Materials design for semiconductor spintronics by ab initio electronic-structure calculation  

International Nuclear Information System (INIS)

A systematic study for the materials design of III-V and II-VI compound-based ferromagnetic diluted magnetic semiconductors is given based on ab initio calculations within the local spin density approximation. The electronic structures of 3d-transition-metal-atom-doped GaN and Mn-doped InN, InP, InAs, InSb, GaN, GaP, GaAs, GaSb, AlN, AlP, AlAs and AlSb were calculated by the Korringa-Kohn-Rostoker method combined with the coherent potential approximation. It is found that the ferromagnetic ground states are readily achievable in V-, Cr- or Mn-doped GaN without any additional carrier doping treatments, and that InN is the most promising candidate for high-T_C ferromagnet. A simple explanation of the systematic behavior of the magnetic states in III-V and II-VI compound-based diluted magnetic semiconductors is also given. It is also shown that V or Cr-doped ZnS, ZnSe, and ZnTe are ...

2003-04-01

88

Preparation, characterization and properties of thermochromic tungsten-doped vanadium dioxide by thermal reduction and annealing  

International Nuclear Information System (INIS)

Thermochromic tungsten-doped vanadium dioxide (VO2) powders were successfully synthesized by thermal reduction using V2O5 as a vanadium precursor. The products were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The results indicated that W was successfully doped into the crystal lattice of VO2 matrix, and prepared tungsten-doped VO2 had a rod-like morphology. The effects of reducing temperature and annealing temperature on the crystallographic structures were also discussed. The phase transition temperature (Tt) of VO2 could be simply tuned by changing the doping concentration of tungsten. When the doping concentration was 1.58 mol%, the Tt could be reduced to 37.8 oC from initial 69.5 oC, suggesting that tungsten-doped VO2 possesses prominent ...

2010-08-20

89

Influence of vanadium doping on the electrochemical behaviour of MnO{sub 2} rutile; Influence du dopage par le vanadium sur le comportement electrochimique de MnO{sub 2} rutile  

Energy Technology Data Exchange (ETDEWEB)

Vanadium doped manganese bi-oxide has been obtained from a solution containing both cations. The X-ray diffraction of this material indicates a rutile-type phase but the enlargement of some lines supports the existence of several lattice defects. Also the particle size of the doped material is significantly smaller than the one of the non-doped material obtained in the same conditions. The presence of pentavalent vanadium inside the lattice leads to a small amount of trivalent manganese. Electron microscopy shows the existence of defects which have a tendency of becoming well-ordered and to stabilize a sur-structure. At ambient temperature, the electrochemical behaviour of doped manganese bi-oxide is greatly improved when compared to the non-doped phase. This behaviour is due to the presence of numerous lattice defects and to the smaller size of crystallites. In polymer batteries, ...

1996-12-31

90

Magnetic ordering in CeM_2Si_2 (M = Ag,Au,Pd,Rh) compounds as studied by neutron diffraction  

International Nuclear Information System (INIS)

We report the results of neutron-diffraction experiments on CeM_2Si_2 (M = Ag,Au,Pd,Rh) which were performed to explore the role of valence fluctuations and 4f hybridization in the magnetic ordering of cerium compounds. All four order antiferromagnetically, the first three exhibiting structures consisting of ferromagnetic layers with moments perpendicular to the layers, which are believed to be characteristic of 4f-4f interactions mediated through hybridization with conduction electrons. CePd_2Si_2 has an anomalously small moment (0.62#mu#/sub B/) in the ordered state. CeAg_2Si_2 exhibits an incommensurate longitudinal, static magnetization wave with moment and propagation direction along the a axis. The fourth compound, CeRh_2Si_2, has the highest known transition temperature (39 K) reported for cerium ordering; it exhibits another second-order transition at 27 K to a complex commensurate structure with modulated moments. The results are ...

91

Magnetic ordering in CeM/sub 2/Si/sub 2/ (M = Ag,Au,Pd,Rh) compounds as studied by neutron diffraction  

Energy Technology Data Exchange (ETDEWEB)

We report the results of neutron-diffraction experiments on CeM/sub 2/Si/sub 2/ (M = Ag,Au,Pd,Rh) which were performed to explore the role of valence fluctuations and 4f hybridization in the magnetic ordering of cerium compounds. All four order antiferromagnetically, the first three exhibiting structures consisting of ferromagnetic layers with moments perpendicular to the layers, which are believed to be characteristic of 4f-4f interactions mediated through hybridization with conduction electrons. CePd/sub 2/Si/sub 2/ has an anomalously small moment (0.62..mu../sub B/) in the ordered state. CeAg/sub 2/Si/sub 2/ exhibits an incommensurate longitudinal, static magnetization wave with moment and propagation direction along the a axis. The fourth compound, CeRh/sub 2/Si/sub 2/, has the highest known transition temperature (39 K) reported for cerium ordering; it exhibits another second-order transition at 27 K to a complex commensurate structure ...

1984-03-01

92

Effect of cerium addition to Ni-Cr anode electrode for molten carbonate fuel cells: Surface fractal dimensions, wettability and cell performance  

Energy Technology Data Exchange (ETDEWEB)

The geometrical and chemical effects of cerium (Ce) addition to Ni-Cr anode electrode in molten carbonate fuel cells (MCFCs) were investigated by measuring the fractal dimensions and wettability of four types of anode electrode with Ce added up to 5 wt.%. In addition, their cell performances were investigated through a single cell operation test and their results were explained based on the wettability of the anode electrodes. The addition of Ce to the anode electrode increased the fractal dimensions and wettabilities of the electrodes. Despite the even larger electrical resistivity of Ce compared to that of Ni and Cr, the electrical resistances of the Ce-added anode electrodes were slightly increased with increasing level of Ce addition. This might be ascribed to the greater wettability of the Ce-added anode electrode that enhanced the cell performance. Therefore, the greater wettability of the Ce-added anode electrode might compensate for its relatively larger ...

2007-02-15

93

Cobalt, titanium or cerium oxide protective coatings for the nickel cathode of the molten carbonate fuel cells; Revetements protecteurs a base d'oxyde de cobalt, de titane ou de cerium pour la cathode de nickel des piles a combustible a carbonates fondus  

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to combine the MCFC cathode Li{sub x}Ni{sub 1-x}O properties to those of the protective coatings of LiCoO{sub 2}, Li{sub 2}TiO{sub 3} or of CeO{sub 2}, less soluble in the molten carbonates. In the cases of LiCoO{sub 2}, have been carried out by controlled potential coulometry in aqueous solution, a deposition of Co{sub 3}O{sub 4} on dense Ni. The cobalt oxide reacts rapidly in the Li{sub 2}CO{sub 3}-Na{sub 2}CO{sub 3} medium at 650 C to give LiCoO{sub 2}, a spinel cubic phase revealed by Raman spectroscopy. (O.M.)

2003-10-15

94

Recovery of rare earths from red mud  

International Nuclear Information System (INIS)

The prospect for the recovery of rare earths from red mud, the bauxite tailings from the production of alumina is examined. The Jamaican red mud by far has the higher trace concentrations of lanthanum, cerium, neodymium, and yttrium. Scandium is also present. The dissolution of the rare earth is a major extraction problem because of the large volume of other materials. The recovery processes that have been proposed include the production of co-products such as iron, alumina, and titanium concentrates, with the rare earths going with the titanium. In this paper a critical examination of the possible processes are presented with the recommended research projects to be carried out.

1992-03-01

95

Development of time-resolved laser fluorescence spectrometry for on-line uranium checking in solutions of the Purex reprocessing process; Developpement de la spectrofluorimetrie laser a resolution temporelle pour le controle en ligne de l`uranium dans les solutions du procede de retraitement purex  

Energy Technology Data Exchange (ETDEWEB)

The Purex process and the fluorescence spectrometry are first recalled, then uranyl fluorescence is studied in a pure nitric medium without other elements to establish a theoretical model, allowing the description of uranium fluorescence signal with a general equation. The influence of different parameters (temperature, inhibitors, dynamic quenching of iron and cerium) is investigated to develop the model. A quantitative analysis method without addition of reagents is proposed to validate the model.

1992-02-25

96

Process development for production of coal/sorbent agglomerates. Final technical report, September 1, 1990--August 31, 1991  

Energy Technology Data Exchange (ETDEWEB)

The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to ...

1991-12-31

97

Method of treating final products from flue gas desulfurization  

Science.gov (United States)

A method of treating final products from a flue gas desulfurization. The flue gas desulfurization is carried out by the absorption of sulfur oxide in a spray dryer with a suspension which contains lime, or in a reactor with a dry, fine-grained, absorbent which contains lime. Prior to desulfurization, the fly ash carried along by the flue gas which is to be desulfurized is separated entirely, partially, or not at all from the flue gas, and the final products from the flue gas desulfurization, prior to any further treatment thereof, amount to 1-99% by weight, preferably 1-70% by weight, of fly ash, and 1-99% by weight, preferably 30-99% by weight, of the sum of the desulfurization products, preferably calcium sulfite hemihydrate, and/or calcium sulfite, and/or calcium sulfate dyhydrate, and/or calcium sulfate hemihydrate, and/or calcium sulfate, as well as residue of the absorbent. ...

1984-10-23

98

A structural and thermodynamic basis for the catalytic behavior of single phase and multiphase bismuth cerium molybdate ammoxidation catalysts  

Energy Technology Data Exchange (ETDEWEB)

The vast majority of fundamental studies of metal oxide selective oxidation catalysts have been performed with single phase systems. These investigations established the basic tenents of the redox mechanism of selective oxidation and ammoxidation catalysis. By comparison, structural and kinetic investigations of multiphase oxide catalysts are less numerous because of the inherent difficulties in understanding the relative contributions of separate phases to the catalytic behavior of the composite catalyst. Some attempts have been made in the past to understand the complex chemistry of multiphase catalysts and additional important insights have been realized more recently. However, a clear understanding of the most significant catalytic interactions between individual phases of a multiphase multicomponent redox catalyst is still lacking. In an effort to provide an understanding and a physical basis for the observed synergism in multiphase oxide catalysts, the structural and chemical ...

1983-09-01

99

Wet limestone FGD solids analysis by thermogravimetry  

Energy Technology Data Exchange (ETDEWEB)

Wet limestone scrubbing is once again becoming a popular technology for removal of sulfur dioxide (SO{sub 2}) from power plant emissions. Critical to the operation of wet limestone flue gas desulfurization (FGD) systems is accurate chemical analysis of scrubber solids. The analytical technique of thermogravimetry is ideal for this application, as the instrument can give precise readings of the principal scrubber solids components, calcium sulfite/sulfate hemihydrate, calcium sulfate dihydrate (gypsum), and unused calcium carbonate. The data provides plant chemists, engineers, and operators with information needed to fine-tune scrubber operation and detect process upsets. (orig.)

2004-07-01

100

Vitamin D and respiratory health  

UK PubMed Central (United Kingdom)

Vitamin D is now known to be of physiological importance outside of bone health and calcium homeostasis, and there is mounting evidence that it plays a beneficial role in the prevention and/or treatment...Full Text Available

2009-10-01

101

Two-photon calcium imaging from head-fixed Drosophila during optomotor walking behavior  

British Library Electronic Table of Contents (United Kingdom)

Drosophila melanogaster is a model organism rich in genetic tools to manipulate and identify neural circuits involved in specific behaviors. Here we present a technique for two-photon calcium imaging in the central brain of head-fixed Drosophila walking on an air-supported ball. The ball's motion is tracked at high resolution and can be treated as a proxy for the fly's own movements. We used the genetically encoded calcium sensor, GCaMP3.0, to record from important elements of the motion-processing pathway, the horizontal-system lobula plate tangential cells (LPTCs) in the fly optic lobe. We presented motion stimuli to the tethered fly and found that calcium transients in horizontal-system neurons correlated with robust optomotor behavior during walking. Our technique allows both behavior ...

2010-01-01

102

Transformation of Verapamil by Cunninghamella blakesleeana  

UK PubMed Central (United Kingdom)

A filamentous fungus, Cunninghamella blakesleeana AS 3.153, was used as a microbial model of mammalian metabolism to transform verapamil, a calcium channel antagonist. The metabolites...Full Text Available

2004-05-01

104

Role of temperature in the spontaneous precipitation of calcium sulfate dihydrate  

Energy Technology Data Exchange (ETDEWEB)

The spontaneous precipitation of calcium sulfate in supersaturated solutions over the temperature range between 25.0 and 80.0 C was investigated by monitoring the solution specific conductivity during desupersaturation. From measurements of the induction times preceding the onset of precipitation the surface energy of the forming solid, identified as gypsum, was found between ca. 12 and 25 mJ/m{sup 2} for the temperature range between 80.0 and 25.0 C, respectively. Kinetics analysis showed that over 50 C it is possible that anhydrous calcium sulfate is forming as a transient phase converting into the more stable calcium sulfate dihydrate. The linear dependence of the rates of precipitation on the relative solution supersaturation suggested a mechanism according to which the growth units are integrated into the active sites of the supercritical nuclei by surface diffusion. According to the morphological examination of the ...

1999-02-16

105

Mechanisms of Reproductive Thermotolerance in Gossypium hirsutum: The Effect of Genotype and Exogenous Calcium Application  

British Library Electronic Table of Contents (United Kingdom)

Abstract Although photosynthetic thermotolerance has been investigated extensively in cotton leaves, reports on the biochemical influence of the pistil in promoting fertilization thermostability are limited. To evaluate the effect of temperature, genotype, and exogenous calcium application on fertilization and pistil biochemistry in cotton, thermosensitive (cv. ST4554 B2RF) and thermotolerant (cv. VH260) plants were grown under control (30/20-C) or high-temperature (38/20-C) conditions during flowering, and exogenous CaCl2 was applied to flowers 1-day prior to anthesis. Measured pistil parameters included fertilization efficiency; protein concentration; glutathione reductase, superoxide dismutase (SOD) and NADPH oxidase activities; and ATP and calcium levels. Exogenous calcium had no effec...

2011-01-01

106

Loss of Skeletal Calcium by Patients on Maintenance Dialysis  

UK PubMed Central (United Kingdom)

Direct radiological measurements of the mineral content of femoral bone were performed in 13 patients on maintenance dialysis. They were found to be sufficiently sensitive to be used for monitoring,...Full Text Available

1970-08-29

107

Instrumental-activation analysis of Mo, Al, Ca, Mn, Cl, Na, and K in soil-plant samples  

International Nuclear Information System (INIS)

... activation analysis aluminium 28 calcium 49 chlorine 38 cotton plants li-drifted

108

Selective emitter using porous silicon for crystalline silicon solar cells  

Energy Technology Data Exchange (ETDEWEB)

This study is devoted to the formation of high-low-level-doped selective emitter for crystalline silicon solar cells for photovoltaic application. We report here the formation of porous silicon under chemical reaction condition. The chemical mixture containing hydrofluoric and nitric acid, with de-ionized water, was used to make porous on the half of the silicon surface of size 125 x 125 cm. Porous and non-porous areas each share half of the whole silicon surface. H{sub 3}PO{sub 4}:methanol gives the best deposited layer with acceptable adherence and uniformity on the non-porous and porous areas of the silicon surface to get high- and low-level-doped regions. The volume concentration of H{sub 3}PO{sub 4} does not exceed 10% of the total volume emulsion. Phosphoric acid was used as an n-type doping source to make emitter for silicon solar cells. The measured emitter sheet resistances at the high- and ...

2009-06-15

109

Neutron Transmutation Doping of Initially p-type Silicon for Production of Uniformly Doped n-type Silicon  

Energy Technology Data Exchange (ETDEWEB)

Neutron transmutation doping(NTD) for producing ntype silicon semiconductor is based on the conversion of the Si-30 isotope into phosphorus atom by neutron absorption reaction. By using this method, silicon semiconductors with extremely uniform n-type dopant distributions can be produced, and this is the dominant advantage of NTD compared with the conventional chemical doping. HANARO has two vertical holes for NTD, and the commercial NTD service for 5 and 6 inch silicon ingots has been going on at the NTD2 hole. Generally, NTD method is applied to the initially n-type silicon material. But, an initially p-type silicon material can also be used for the production of uniformly doped n-type silicon by using NTD method. Therefore, in this work, we investigated the relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material. Thereafter, we established the methodology ...

2007-10-15

110

Neutron Transmutation Doping of Initially p-type Silicon for Production of Uniformly Doped n-type Silicon  

International Nuclear Information System (INIS)

Neutron transmutation doping(NTD) for producing ntype silicon semiconductor is based on the conversion of the Si-30 isotope into phosphorus atom by neutron absorption reaction. By using this method, silicon semiconductors with extremely uniform n-type dopant distributions can be produced, and this is the dominant advantage of NTD compared with the conventional chemical doping. HANARO has two vertical holes for NTD, and the commercial NTD service for 5 and 6 inch silicon ingots has been going on at the NTD2 hole. Generally, NTD method is applied to the initially n-type silicon material. But, an initially p-type silicon material can also be used for the production of uniformly doped n-type silicon by using NTD method. Therefore, in this work, we investigated the relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material. Thereafter, we established the methodology ...

2007-10-01

111

The effects of a calcium deficient diet on the mechanical properties and morphology of goose bone.  

Science.gov (United States)

A control group of geese (Anser anser) on a normal calcium diet for egg laying poultry was compared to egg laying geese on a calcium deficient diet. The ultimate compressive strength and modulus of elasticity of femoral cortical bone from each group were determined by compressing right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The bending strength and bending modulus of elasticity of tibial cortical bone were determined by three point bend tests on rectangular prisms which were approximately 25 mm by 0.8 mm by 0.8 mm. Bone calcium content and eggshell calcium content were determined by atomic absorption spectrophotometry. Blood samples were analyzed for free calcium ion concentration. Histological observations included studies of cross-sectional microradiographs, examinations of cross sections stained by a modified Masson's technique, and a determination ...

1986-01-01

112

Thulium-doped vanadate crystals: Growth, spectroscopy and laser performance  

British Library Electronic Table of Contents (United Kingdom)

This work is concentrated on growth, spectroscopy and laser performance of thulium-doped vanadate crystals. At the beginning the growth techniques are analyzed and then the matrix of vanadates crystal, its structure and physicochemical properties are explained together with the rare earth activators influence. Detailed spectroscopy of the thulium-doped vanadate crystals then follows. On the background of this theoretical analysis and state of the art of the subject the description of thulium vanadate lasers (especially Tm:YVO"4, Tm:GdVO"4, and Tm:LuVO"4) together with their generated output radiation characteristics are presented.

2011-01-01

113

Temperature Dependences of Leakage Currents of ZnO Varistors Doped with Rare-Earth Oxides  

British Library Electronic Table of Contents (United Kingdom)

Rare-earth oxides are doped into ZnO varistors as grain growth inhibitors for increasing the varistors' voltage gradients. However, their leakage currents become large and their nonlinear coefficients decrease at the same time. The reasonable explanation for such a phenomenon has not yet been available. In this paper, the temperature dependences of varistor samples' leakage currents are investigated, which reveal that the increased leakage currents of ZnO varistors with Y2O3 doping are mainly due to the bypass paths through the intergranular materials at grain corners.

2010-01-01

114

Surface doping of conjugated polymers by graphene oxide and its application for organic electronic devices  

Energy Technology Data Exchange (ETDEWEB)

Surface doping of conjugated polymers is realized by depositing a thin layer of graphene oxide (GO) on top of the polymers. The high proton density and the unique 2D structure of GO facilitate the protonic surface doping of conjugated polymers to achieve high conductivities. This finding represents a new strategy for improving charge transport across the metal/conjugated polymer interface to achieve much improved performance in organic solar cells. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

2011-04-26

115

Impedance spectroscopy study with H-doped ammonium uranylphosphate self supported membranes  

International Nuclear Information System (INIS)

Equivalent circuit and electrical parameters for H-doped NH_4UO_2PO_4.3H_2O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).

116

Electron paramagnetic resonance of nitroxide-doped magnetic fluids  

Energy Technology Data Exchange (ETDEWEB)

Electron paramagnetic resonance was used to investigate surface-coated magnetite-based magnetic fluids doped with TEMPOL. Two magnetic fluid samples, having magnetite nanoparticles with average diameter of 94 A and coated with different coating layers (lauric acid plus ethoxylated polyalcohol in one case and oleoylsarcosine in the other case), were doped with TEMPOL (6 mM and pH 7.4) and investigated as a function of the nanoparticle concentration. The resonance field and the resonance linewidth both scale linearly with the nanoparticle concentration.

2002-11-01

118

The Effect of Boron on the Mechanical Behavior of Copper ...  

Science.gov (United States)

... 500 ppm, boron increases the 0.2% offset strength; results show that boron doping does not appreciably affect ultimate compressive strength; for 0 ...

119

Nitrogen doping into titanium dioxide by the sol?gel method using nitric acid  

British Library Electronic Table of Contents (United Kingdom)

N-doped TiO2 has been prepared by use of sol?gel systems containing titanium alkoxide, with nitric acid as the nitrogen source. The time needed for gelation of the systems was drastically reduced by ultrasonic irradiation. The peaks assigned to the nitrate and nitrous ions were observed by FT-IR measurement during the sol?gel reaction. The N-doping was confirmed by the observation of N?O peaks in the XPS spectrum of the sample heated at 400??C. The nitrate ion acted as an oxidizer of the ethanol solvent and titanium species. The TiO2 became doped with nitrogen oxide species as a result of reduction of nitrate ion incorporated into the dried gel samples. These results indicated that the added nitric acid was reduced during the sol?gel transition and heating process, and the resulting NO spe...

2011-01-01

120

Microstructure and properties of ultrafine WC-10Co composites with chemically doped VC  

British Library Electronic Table of Contents (United Kingdom)

Vanadium carbide is the most effective grain growth inhibitor for ultrafine WC-Co composites due to its high solubility and mobility in the cobalt phase at relatively low temperatures; however, there are still some debates over the best way to introduce it into the WC-Co formulation. In this paper, the differences between admixed and chemically doped grain growth inhibitors on the microstructural development and properties of an ultrafine WC-10Co composite are discussed. The densification rate of chemically doped samples is slower in the early stage of sintering and the WC grain sizes of the sintered alloys are finer than those of admixed samples, leading to the increase of hardness and transverse rupture strength of the sintered alloys. The effectiveness of the chemically doped inhibitor ...

2011-01-01

121

Microscopic Origin of the Phenomenological Equilibrium ''Doping Limit Rule'' in n -Type III-V Semiconductors  

International Nuclear Information System (INIS)

The highest equilibrium free-carrier doping concentration possible in a given material is limited by the ''pinning energy'' which shows a remarkable universal alignment in each class of semiconductors. Our first-principles total energy calculations reveal that equilibrium n -type doping is ultimately limited by the spontaneous formation of close-shell acceptor defects: the 3- -charged cation vacancy in AlN, GaN, InP, and GaAs and the 1- -charged DX center in AlAs, AlP, and GaP. This explains the alignment of the pinning energies and predicts the maximum equilibrium doping levels in different materials. (c) 2000 The American Physical Society

2000-02-07

122

Large Magnetic Moments of Arsenic-Doped Mn Clusters and their Relevance to Mn-Doped III-V Semiconductor Ferromagnetism  

CERN Document Server

We report electronic and magnetic structure of arsenic-doped manganese clusters from density-functional theory using generalized gradient approximation for the exchange-correlation energy. We find that arsenic stabilizes manganese clusters, though the ferromagnetic coupling between Mn atoms are found only in Mn$_2$As and Mn$_4$As clusters with magnetic moments 9 $\\mu_B$ and 17 $\\mu_B$, respectively. For all other sizes, $x=$ 3, 5-10, Mn$_x$As clusters show ferrimagnetic coupling. It is suggested that, if grown during the low temperature MBE, the giant magnetic moments due to ferromagnetic coupling in Mn$_2$As and Mn$_4$As clusters could play a role on the ferromagnetism and on the variation observed in the Curie temperature of Mn-doped III-V semiconductors.

2005-01-01

123

Experimental and analytical study of saturation current density of laser-doped phosphorus emitters for silicon solar cells  

British Library Electronic Table of Contents (United Kingdom)

Heavily doped emitters with low saturation current density are of particular interest for selective emitter solar cells. These emitters can be obtained by laser doping through the phosphosilicate glass layer formed after thermal diffusion from POCl3 gas. The experimental results show that in contrast to purely POCl3 furnace-diffused emitters, the saturation current density of laser-doped emitters does not increase linearly as sheet resistance decreases, but rather features two distinct regimes. In one of these regimes, the saturation current density is found to decrease as the sheet resistance decreases, reaching values lower than those of furnace emitters. This peculiar behaviour was explained by both qualitative analysis and numerical simulations.

2011-01-01

125

Effects of lithium iodide doping on devolatilization characteristics of brown coals; Yoka lithium no tenka ga kattan no kanetsu henka katei ni oyobosu eikyo  

Energy Technology Data Exchange (ETDEWEB)

In order to discuss effects of lithium iodide (LiI) doping on condensation structure of brown coals during heating, spectral changes were measured by using an in-situ FT-IR. It was found that the LiI doping accelerates weight reduction due to heating, and the doping effect is affected by coal structure. Both of Loy Yang (LY) coal and its LiI doped coal (DLY) had absorption intensity of the FT-IR spectra decreased with rising temperature, and the absorption center belonging to an OH group shows different shifts between the LY and DLY coals. This indicates that the LiI doping has affected the change in hydrogen bonding patterns associated with heating. Both of South Banko (SB) and LY coals had the absorption spectral intensity in the OH group decreased as the weight reduction (conversion) rate increased. Reduction in the OH groups associated with heating is caused by volatilization ...

1996-10-28

126

Double perovskite catalysts for oxidative coupling  

Energy Technology Data Exchange (ETDEWEB)

Alkali metal doped double perovskites containing manganese and at least one of cobalt, iron and nickel are useful in the oxidative coupling of alkane to higher hydrocarbons.

1991-01-01

127

Boron transient enhanced diffusion in heavily phosphorus doped silicon  

International Nuclear Information System (INIS)

A study has been made of B transient enhanced diffusion (TED) in heavily P-doped Si using secondary ion mass spectroscopy (SIMS) and positron annihilation spectroscopy (PAS). The P-doped silicon was implanted with boron ions of 40 keV energy to a dose of 3 x 10"1"4 cm"-"2, and then annealed at temperatures ranging from 700--1,000 C in a N_2 ambient for varying durations. As P doping concentration increased from 3 x 10"1"9 to 1 x 10"2"0 cm"-"3, boron diffusivity and the immobile boron fraction decreased. The experimental results are inconsistent with the predictions of the Fermi-level model and suggest that the clustering between B atoms and Si interstitials should be invoked in order to explain the immobile portion of the B peak during TED.

1996-12-02

128

A novel single-step synthesis of N-doped TiO"2 via a sonochemical method  

British Library Electronic Table of Contents (United Kingdom)

A novel single-step synthetic method for the preparation of anatase N-doped TiO"2 nanocrystalline at low temperature has been devoleped. The N-doped anatase TiO"2 nanoparticles were synthesized by sonication of the solution of tetraisopropyl titanium and urea in water and isopropyl alcohol at 80^oC for 150min. The as-prepared sample was characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and UV-vis absorption spectrum. The product structure depends on the reaction temperature and reaction time. The photocatalytic activity of the as-prepared photocatalyst was evaluated via the photodegradation of an azo dye direct sky blue 5B. The results show that the N-doped TiO"2 nanocrystalline prepared via sonication exhibit an excellent photocatalytic...

2011-01-01

129

A first principles study on optical transparency mechanism in Dy doped #alpha#-SiAlON ceramics  

International Nuclear Information System (INIS)

Dy doped #alpha#-SiAlON ceramics prepared by the hot-pressing method show a high optical transmittance value, >70%, in the infrared region of 1.5-4.5 #mu#m. First principles calculations have been carried out to reveal the underlying transparency mechanism. It is found that the valence shell of doped Dy atoms interacts strongly with the doping states of #alpha#-SiAlON, resulting in the increase in the optical gap from 0.4 to 1.1 eV, which suppresses the photoabsorption in the wavelength region longer than 1.0 #mu#m and leads to the good transparency property. The calculated optical transmission spectra are in good agreement with the corresponding experiments.

2009-11-01

130

Selective Expression in Carotid Body Type I Cells of a Single Splice Variant of the Large Conductance Calcium- and Voltage-activated Potassium Channel Confers Regulation by AMP-activated Protein Kinase*  

UK PubMed Central (United Kingdom)

Inhibition of large conductance calcium-activated potassium (BKCa) channels mediates, in part, oxygen sensing by carotid body type I cells. However, BKCa channels remain active...Full Text Available

2011-04-08

131

Physicochemical basis for formation of renal stones of calcium phosphate origin: calculation of the degree of saturation of urine with respect to brushite  

UK PubMed Central (United Kingdom)

Brushite (CaHPO4·2H2O) was considered to govern the formation of renal calculus of calcium phosphate origin. The degree of saturation of urine with respect to this phase...Full Text Available

1969-10-01

132

Effects of xylitol on the absorption of /sup 203/Pb in mice and cockerels  

Energy Technology Data Exchange (ETDEWEB)

Earlier studies have indicated that xylitol may increase the absorption and urinary excretion of dietary oxalate. It has also been indicated that xylitol increases the absorption of calcium. Intestinal absorption of lead, a divalent contaminant in the diet, is in many respects similar to that of calcium. The purpose of this study was to evaluate the effects of xylitol on the intestinal absorption of lead using two different approaches: the in situ ligated intestinal loop technique in cockerels and gastric gavage in mice.

1986-07-01

133

Solid-gas equilibria in CaSO/sub 3/-H/sub 2/O/sub (g)/ system and Lewis-acid-base alloys  

Energy Technology Data Exchange (ETDEWEB)

The role played by calcium sulfite in the flue gas desulfurization of lime/limestone scrubbers makes it desirable to work out its thermodynamic properties. A thermogravimetric apparatus was used to study the equilibria between calcium sulfite hemihydrate and calcium sulfite anhydrite under different conditions. Efforts were made to analyze the difficulties encountered in the dynamic approach to equilibration after calcium sulfate dihydrate failed in calibration of the apparatus. Finally, the kinetics and thermodynamics for the dissociation of calcium sulfite hemihydrate were examined. The confirmation of Engel-Brewer's correlation between the electronic configuration and crystal structure in metallic systems has long been pursued in this group by studying the Lewis-acid-base interactions. Tantalum-iridium alloys of different compositions were brought into equilibrium with ...

1981-10-01

134

Human complement protein C99 is a calcium binding protein  

International Nuclear Information System (INIS)

Human complement protein C9 is shown to be a metalloprotein that binds 1 mol of Ca"2"+/mol of C9 with a dissociation constant of 3 #mu#m as measured by equilibrium dialysis. Incubation with EDTA removes the bound calcium, resulting in a apoprotein with decreased thermal stability. This loss in stability leads to aggregation and, therefore, to loss of hemolytic activity upon heating to a few degrees above the physiological temperature. Heat-induced aggregation of apoC9 can be prevented by salts that stabilize proteins according to the Hofmeister series of lyotropic ions, suggesting that the ion in native C9 may ligand with more than one structural element of domain of the protein. Ligand blotting indicates that the calcium binding site is located in the amino-terminal half of the protein. Removal of calcium by inclusion of EDTA in assay mixtures has no effect on the hemolytic activity of C9, and its capacity to bind to C8 in ...

135

Optical in situ size determination of single lanthanide-ion doped oxide nanoparticles  

Science.gov (United States)

We show that the size of a lanthanide-ion doped nanoparticle can be accurately determined from its luminosity. The optically determined size distribution is in very good agreement with the distribution obtained from transmission electron microscopy. These data confirm that single nanoparticles are visualized in microscopy experiments. Nanoparticles as small as 13 nm are detectable with integration times of 500 ms.

2006-12-01

136

Morphology-controlled synthesis and novel microwave electromagnetic properties of hollow urchin-like chain Fe-doped MnO2 under 10 T high magnetic field  

International Nuclear Information System (INIS)

Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized under a high magnetic field of 10 T. The formation mechanism was investigated and discussed in detail. The synthesized samples were characterized by XRD, SEM, TEM, EMPA, and vector network analysis. By doping MnO2 with Fe, the relative complex permittivity of MnO2 and its corresponding loss tangent clearly decreases, but its relative complex permeability and its corresponding loss tangent markedly increases. Moreover, the theoretically calculated values of reflection loss show that with increasing the Fe content, the as-prepared Fe-doped MnO2 exhibits good microwave absorption capability. -- Graphical Abstract: Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized in a high magnetic field of 10 T via a simple chemical process. Display Omitted Highlights: ? Fe-doped MnO2 ...

2011-05-01

137

Molecules with polymerizable ligands as precursors to porous doped materials  

Energy Technology Data Exchange (ETDEWEB)

Titanium and aluminum alkoxide derivatives with polymerizable ligands such as 2-(methacryloyloxy)ethylacetoacetate (HAAEMA), oleic acid and geraniol (HOGE) have been obtained. The various compounds have been characterized by FT-IR and NMR {sup 1}H. Copolymerization with styrene and divinylbenzene affords porous doped organic materials which have been characterized by scanning electron microscopy (SEM), elemental analysis, density measurements.

1996-12-31

138

Ferromagnetism in Mn-doped GaAs layers: Effects of laser annealing  

Energy Technology Data Exchange (ETDEWEB)

The properties of Mn-doped GaAs layers grown by laser deposition were investigated with measurements of Hall effect and magneto-optical Kerr effect (MOKE). The electrical and magnetic parameters of the layers were defined by growth temperature and quantity of sputtered Mn. It was shown that room-temperature ferromagnetism is revealed by MOKE and, after ruby laser 25 ns pulse annealing, by Hall effect measurements.

2006-05-15

139

Conductivity of doped N-carbazolyl-substituted polysilanes  

Energy Technology Data Exchange (ETDEWEB)

A series of N-carbazolyl-substituted silane homo- and copolymers has been prepared by Wurtz coupling. Doping with iodine on these copolymer films increases the electrical conductivity to the range 10{sup -6}-10{sup -3} S cm{sup -1}. The conductivity depends strongly on the composition of the copolymer; it reaches the maximum value for N-carbazolyl-substituted silane homopolymer. The effects of carbazolyl group on conductivity and charge transport mechanisms in the polymer are discussed. (orig.)

1995-08-01

140

A real time neutron diffraction study on the reaction of AsF_5 with deuterated polyparaphenylene  

International Nuclear Information System (INIS)

The doping of deuterated polyparaphenylene [C_6D_4]sub(n) with AsF_5 has been investigated by real time neutron diffractometry at 100, 400 and 820 mbar AsF_5 pressure. The reaction appears to be diffusion controlled. Evidence for one doped phase with partial crystalline order was obtained. Structural considerations suggest two polymer chains plus one dopant ''string'' as the repetitive unit. (Auth.).

1982-01-01

141

Theoretical study on the effects of oxygen doping on the lithium ion conductive perovskite-type manganese fluoride of KxBa(1-x)/2MnF3  

British Library Electronic Table of Contents (United Kingdom)

Previously, we demonstrated that the lithium ion conduction in the perovskite-type manganese fluoride is attributed to counter cation-site vacancy mechanism. The divalent counter cation-doped KxBa(1-x)/2MnF3 was theoretically predicted as the lithium ion conductor in the perovskite-type manganese fluoride. In this study, we considered the oxygen doping for KxBa(1-x)/2MnF3 to realize the higher lithium ion conductivity. It is because lithium ion forms the stronger ionic bond with the doped oxygen anion. The hybrid-DFT calculations were performed to investigate the lithium ion conduction in the oxygen-doped KxBa(1-x)/2MnF3. The calculation results were discussed from the viewpoints of the potential energy curve, electron densities, and charge and spin densities. The effect of the lithium ion...

2009-01-01

142

Synthesis of (Bi0.5Na0.5)TiO3 (BNT) and Pr doped BNT using the soft combustion technique and its properties  

British Library Electronic Table of Contents (United Kingdom)

In this work, bismuth sodium titanate (Bi0.5Na0.5)TiO3 (BNT) and praseodymium (Pr)-doped BNT were successfully produced using the soft combustion technique. The effects of Pr doping on stoichiometry, microstructure, density and dielectric properties were studied. Pure Pr-doped BNT was obtained in all samples containing 5, 10 and 20mol% Pr after calcination at 800^oC for 3h. The produced powders were then pressed into pellets and sintered at 1100^oC for 3h. The very similar ionic radii of Pr^3^+ with Bi^3^+ and Na^+ made it possible to substitute both Bi and Na. The crystallite size and grain size decreased with increasing Pr amount because Pr acted as grain growth inhibitor, both for calcined powders and for sintered pellets. Maximum density was obtained in 5mol% Pr-doped BNT, beyond which...

2011-01-01

143

Evaluation of paramagnetic species in coals with iodine doping technique; Yoso tenkaho wo mochiita sekitanchu no jojiseishu no hyoka  

Energy Technology Data Exchange (ETDEWEB)

Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability ...

1996-10-28

144

Comparison of the performance of photonic band-edge liquid crystal lasers using different dyes as the gain medium  

Science.gov (United States)

The primary concern of this work is to study the emission characteristics of a series of chiral nematic liquid crystal lasers doped with different laser dyes (DCM, pyrromethene 580, and pyrromethene 597) at varying concentrations by weight (0.5-2 wt %) when optically pumped at 532 nm. Long-wavelength photonic band-edge laser emission is characterized in terms of threshold energy and slope efficiency. At every dye concentration investigated, the pyrromethene 597-doped lasers exhibit the highest slope efficiency (ranging from 15% to 32%) and the DCM-doped lasers the lowest (ranging from 5% to 13%). Similarly, the threshold was found to be, in general, higher for the DCM-doped laser samples in comparison to the pyrromethene-doped laser samples. These results are then compared with the spectral properties, quantum efficiencies and, where possible, fluorescence lifetimes of the dyes ...

2010-02-01

145

Aging and compatbility of TNF-doped mylar  

Energy Technology Data Exchange (ETDEWEB)

TNF-doped Mylar is a new radiation-hard dielectric that has recently been qualified as a viable substitute for Mylar in capacitors. The advantage of TNF-doped Mylar is that it satisfies both the nuclear safety and radiation hardness requirements of weapons. Mylar is not radiation-hard. Aging and compatibility studies were carried out to insure that (1) TNF does not diffuse from the film during fabrication of the capacitor or during storage; and (2) there are no compatibility problems with aluminum foil (the conductor) or Fluorinert (the secondary dielectric). Losses of TNF were barely detectable during the vacuum bakes used in fabricating capacitors or during accelerated aging tests carried out below T{sub g} (70C) over a two year period in air. In other accelerated tests, no compatibility problems were detected with aluminum or Fluorinert. TNF-doped Mylar is now being used in the MC-4109 capacitor that was called out for ...

1990-01-01

146

Small-molecule screen identifies inhibitors of a human intestinal calcium-activated chloride channel.  

Science.gov (United States)

Calcium-activated chloride channels (CaCCs) are widely expressed in mammalian tissues, including intestinal epithelia, where they facilitate fluid secretion. Potent, selective CaCC inhibitors have not been available. We established a high-throughput screen for identification of inhibitors of a human intestinal CaCC based on inhibition of ATP/carbachol-stimulated iodide influx in HT-29 cells after lentiviral infection with the yellow fluorescent halide-sensing protein YFP-H148Q/I152L. Screening of 50,000 diverse, drug-like compounds yielded six classes of putative CaCC inhibitors, two of which, 3-acyl-2-aminothiophenes and 5-aryl-2-aminothiazoles, inhibited by >95% iodide influx in HT-29 cells in response to multiple calcium-elevating agonists, including thapsigargin, without inhibition of calcium elevation, calcium-calmodulin kinase II activation, or cystic fibrosis transmembrane conductance ...

2007-12-14

147

Molecular mechanisms of the epithelial transport of toxic metal ions, particularly mercury, cadmium, lead, arsenic, zinc, and copper. Progress report, January 1, 1979-December 31, 1979  

International Nuclear Information System (INIS)

The mechanism of lead transport is presented, and especially the particular similarities or dissimilarities between lead and calcium in this process. The absorption of these metals was determined cockerels, raised on a commercial diet or on a specified diet, using in vivo ligated loop procedure. The dose administered into the loop contained 0.5 #mu#Ci "2"0"3Pb (and/or 0.1 #mu#Ci "4"7Ca), and 0.01 mM lead acetate (and/or mM CaCl_2) in 0.5 ml 0.15 M NaCl,pH 6.5. It was shown that lead is rapidly taken up by the mucosal tissue, and slowly transferred into the body, whereas less calcium is retained by the tissue and the transfer of calcium is many times as effective as that for lead. They appear to respond in a similar manner to a low calcium intake and vitamin D treatment. Increasing luminal stable lead concentration significantly reduced the percentage of radiolead significantly reduced the percentage of ...

148

The ternary system cerium-palladium-silicon  

International Nuclear Information System (INIS)

Phase relations in the ternary system Ce-Pd-Si have been established for the isothermal section at 800 deg. C based on X-ray powder diffraction and EMPA techniques on about 130 alloys, which were prepared by arc-melting under argon or powder reaction sintering. Eighteen ternary compounds have been observed to participate in the phase equilibria at 800 deg. C. Atom order was determined by direct methods from X-ray single-crystal counter data for the crystal structures of #tau#_8-Ce_3Pd_4Si_4 (U_3Ni_4Si_4-type, Immm; a=0.41618(1), b=0.42640(1), c=2.45744(7) nm), #tau#_1_6-Ce_2Pd_1_4Si (own structure type, P4/nmm; a=0.88832(2), c=0.69600(2) nm) and also for #tau#_1_8-CePd_1_-_xSi_x (x=0.07; FeB-type, Pnma; a=0.74422(5), b=0.45548(3), c=0.58569(4) nm). Rietveld refinements established the atom arrangement in the structures of #tau#_5-Ce_3PdSi_3 (Ba_3Al_2Ge_2-type, Immm; a=0.41207(1), b=0.43026(1), c=1.84069(4) nm) and #tau#_1_3-Ce_3_-_xPd_2_0_+_xSi_6 (0#<=#x#<=#1, Co_2_0Al_3B_6-type, ...

2009-09-01

149

Study of the light yield of LuAP:Ce scintillating crystals  

Energy Technology Data Exchange (ETDEWEB)

We have obtained optically clear samples of LuAP:Ce from the Institute of Physical Research, Ashtarak, Armenia, measuring up to 5x5x40 mm{sup 3}. The photo electron yield for a number of theses samples was measured with a Philips XP2020Q photomultiplier tube, and 556 photo electrons per MeV was obtained for the best samples. This is comparable to what is obtained from BGO crystals under the same condition, but a factor of 5 less than what is obtained with an LSO sample of similar dimensions. The light in LuAP:Ce increases with cerium concentration between 0.13 and 0.47%.

1996-12-31

150

Magnetic susceptibility and electrical properties of Ln/sub 2/3+x/TiO/sub 3+y/ (Ln = Ce, Nd) at 77-450/sup 0/K  

Energy Technology Data Exchange (ETDEWEB)

The magnetic susceptibility and electrical resistivity in cerium and neodymium titanate bronzes in Ln/sub 2/3+x/TiO/sub 3+y/ of the perovskite structure were investigated in the temperature range 77-450/sup 0/K. The deviation of the 1/x = f(T) dependence from the Curie-Weiss law, found for a majority of the compositions, was interpreted from the crystal-field effect based on the state of the Ce/sup 3 +/ and Nd/sup 3 +/ cations. For a number of the phases, a transition from metallic conductivity at high temperatures to semiconducting conductivity was detected at temperatures below 200-250/sup 0/K, which agrees well with the conclusion about the temperature dependence of x, related to the subsystem of Ti/sup 3 +/ cations.

1987-01-01

151

Investigation and analytical use of rare earth ionic associates with benzilic acid and rhodamine B  

International Nuclear Information System (INIS)

Ions of rare earth elements (r.e.e.) have been found to form with benzilic acid and rhodamine B precipitates hardly soluble in water and extractable by toluene. The conditions of La and Pr determination by extraction-spectrophotometry method are studied. Relative square deviation does not exceed 0.027 and 0.034 respectively. The method can be used for determination of other cerium sub-group r.e.e. in their salts and cannot be employed for determination of lighter r.e.e. in the presence of heavier r.e.e., because the latter form low soluble precipitates capturing the r.e.e. situated in the beginninq of the r.e.e. series.

1977-01-01

152

Thermal stability of mixed-cation #alpha#-sialon ceramics  

International Nuclear Information System (INIS)

A series of #alpha#-sialon (#alpha#') compositions containing mixed stabilising cations were prepared, by introducing additional CaO to a basic Sm #alpha#-sialon compositions. The thermal stability of these Sm-Ca-containing #alpha#-sialon phases was investigated using XRD, SEM and EDXS techniques. It was found that the addition of calcium into the Sm #alpha#-sialon systems greatly improved the stability of the #alpha#-sialon phases. Calcium was found to be incorporated into the #alpha#-sialon structure, coexistent with the samarium, and partitioning of the calcium and samarium was observed between the #alpha#' phase and grain boundary phases. This indicates a technique which may be used to improve the thermal stability of the #alpha#' phase while maintaining good refractory phases at the sialon grain boundaries.

2003-01-02

153

Spermatozoa of Sharpsnout sea bream (Diplodus puntazzo) and European sea bass (Dicentrarchus labrax) express opioid receptors  

British Library Electronic Table of Contents (United Kingdom)

Endogenous opioid peptides (EOP) are molecules affecting many biological functions influencing productive and reproductive performance. They increase in stress conditions and interact with specific opioidergic receptors (OR): delta, kappa and mu. Several studies in other animal species suggest that they can also affect sperm cell motility. In fish the ionic external environment modulates the increase of intracellular calcium ion that is required to activate sperm motility after spawning. In mammals OR are functionally associated to calcium channels and in fishes calcium is highly required for fish sperm activation. In this study the presence of OR on spermatozoa of two Perciform fish, the sharpsnout seabream (Diplodus puntazzo, family Sparidae) and the European sea bass (Dicentrarchus labr...

2010-01-01

154

Separation of lithium and calcium isotopes during chemical isotopic exchange in extraction systems with phosphoryl-containing podands  

International Nuclear Information System (INIS)

A study was made on extraction of a series of lithium and calcium salts by monopodands L with common formula R-C_6H_4-O-(CH_2CH_2O)_n-C_6H_4-R, where R - CH_2P(O)Ph_2, n 1-3. Extraction-chromatographic separation of lithium and calcium isotopes in systems of metal aquacomplex-solvatocomplex with L in organic phase was conducted. It was established that separation coefficients of "6Li/"7Li isotopes ranged between 1.003 #+-#0.001 and 1.017 #+-#0.002 at the maximal separation degree equal to 1.60. Separation of "4"0Ca/"4"4Ca isotopes was not fixed. 12 refs., 4 figs., 1 tab.

155

Process for producing calcium sulfate dihydrate during desulfurization of stack gases from power station boilers. Verfahren zur Herstellung von Calciumsulfat-Dihydrat im Zuge der Entschwefelung von Rauchgasen aus Kraftwerkskesselfeuerungen  

Energy Technology Data Exchange (ETDEWEB)

This is a process for producing calcium sulfate dihydrate during desulfurization of stack gases from power station boilers, where the stack gases are introduced into a washing tower and are treated with a washing water suspension containing lime in the washing tower, where oxygen in the form of air or of air enriched in oxygen is also blown into the washing tower, and where the washing water suspension drawn off from the washing tower is fed back to the washing tower at a temperature of 45 to 50/sup 0/C in the circuit and at least part of the flow goes via a thickener and where calcium sulfate dihydrate slurry is drawn off from the thickener.

1986-06-12

156

Nanoscale calcium bismuth mixed oxide with enhanced photocatalytic performance under visible light  

British Library Electronic Table of Contents (United Kingdom)

The objective of materials research is the development of economical, safe and efficient synthesis routes that lead to the formation of a photocatalyst which is able to overcome performance problems related to particle size, crystallinity, or low surface area. Here, we report high-quality functional nanoparticles of calcium bismuth mixed oxide with 15nm nominal size corresponding to a specific surface area of 41m^2/g which were produced by single-step flame spray synthesis (FSS). The high temperature of the flame afforded creation of oxygen vacancies which were quantified by near edge X-ray absorption fine structure (NEXAFS) spectra. These two parameters, developed active surface area and created in the flame oxygen vacancies, allowed to enhance the photocatalytic activity of calcium bismu...

2010-01-01

157

Mineral carbonation accelerated by dicarboxylic acids as a disposal process of carbon dioxide  

British Library Electronic Table of Contents (United Kingdom)

Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...

2011-01-01

158

Luminescence properties of thallium crystal phosphors and their use in determining microgram quantities of thallium  

Energy Technology Data Exchange (ETDEWEB)

The preparation and luminescence properties of crystal phosphors based on alkali metal iodide and calcium oxide substrates were studied. The highest luminescence intensities were achieved with iodide substrates at 200/sup 0/ and with the calcium oxide substrate at 800/sup 0/. The calibration graphs were linear in the thallium concentration ranges 0.03-5.0 and 0.1-2.0 mu g using sodium and potassium oxides, respectively, and in the range 0.05-5 mu g using cesium iodide and calcium oxide. A method is proposed for the determination of down to 3 x 10/sup -4/% thallium in rocks, using a crystal phosphor with sodium iodide substrate.

1986-02-01

159

Depression of calcium pump activity in renal cortex of vitamin D-deficient rats with secondary hyperparathyroidism  

Energy Technology Data Exchange (ETDEWEB)

To examine the hormonal regulation of the ATP-dependent Ca{sup 2+} pump in the kidneys, the ATP-dependent Ca{sup 2+} uptake by the basolateral membrane vesicles in the renal cortex was measured using radioactive calcium ({sup 45}Ca{sup 2+}) in rats with vitamin D deficiency or rats undergoing thyroparathyroidectomy. The V{sub max} of the Ca{sup 2+} pump activity was increased not only by administering calcitriol, but also by normalizing the serum calcium level in vitamin D-deficient rats. PTH suppressed the Ca{sup 2+} pump activity in normocalcemic vitamin D-deficient rats. Thyroparathyroidectomy did not affect the Ca{sup 2+} pump activity in the kidneys of normal rats. It was concluded that the ATP-dependent Ca{sup 2+} pump activity was depressed by secondary hyperparathyroidism in vitamin D-deficient rats. (author).

1990-01-01

160

Depression of calcium pump activity in renal cortex of vitamin D-deficient rats with secondary hyperparathyroidism  

International Nuclear Information System (INIS)

To examine the hormonal regulation of the ATP-dependent Ca"2"+ pump in the kidneys, the ATP-dependent Ca"2"+ uptake by the basolateral membrane vesicles in the renal cortex was measured using radioactive calcium ("4"5Ca"2"+) in rats with vitamin D deficiency or rats undergoing thyroparathyroidectomy. The V_m_a_x of the Ca"2"+ pump activity was increased not only by administering calcitriol, but also by normalizing the serum calcium level in vitamin D-deficient rats. PTH suppressed the Ca"2"+ pump activity in normocalcemic vitamin D-deficient rats. Thyroparathyroidectomy did not affect the Ca"2"+ pump activity in the kidneys of normal rats. It was concluded that the ATP-dependent Ca"2"+ pump activity was depressed by secondary hyperparathyroidism in vitamin D-deficient rats. (author).

161

Chemistry of strontium  

International Nuclear Information System (INIS)

This paper describes stable strontium as composed of four stable isotopes ( Sr 88, Sr 87, Sr 86, and Sr 84), of which Sr 88 contributes more than 82% to its composition. Strontium exists in three crystalline, plymorphic forms; face-centered cubic alpha form, hexagonal beta form and body-centered cubic gamma form. Strontium occupies in many physicochemical aspects an intermediate position between calcium and barium, as does the solubility of strontium salts. As a result of its oxidation potential, strontium readily forms oxides, halides, and sulfide. The author proposes that the slight discrimination against strontium incorporation into bony tissues may be due to the difference in ionic potential (14%) between strontium and calcium. Ionic potential is an indicator of the strength of ionic bonds: strontium has a smaller ratio of ionic charge to ionic radius when compared with calcium.

162

Study of ytterbium doping effects on structural, mechanical and opto-thermal properties of sprayed ZnO thin films using the Boubaker Polynomials Expansion Scheme (BPES)  

Energy Technology Data Exchange (ETDEWEB)

In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C{sub 3}H{sub 8}O), water (H{sub 2}O) and zinc acetate (Z{sub n}(CH{sub 3}CO{sub 2}){sub 2}) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(lambda) and ...

2009-10-19

163

Study of ytterbium doping effects on structural, mechanical and opto-thermal properties of sprayed ZnO thin films using the Boubaker Polynomials Expansion Scheme (BPES)  

International Nuclear Information System (INIS)

In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C3H8O), water (H2O) and zinc acetate (Zn(CH3CO2)2) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(?) and reflectance R(?) spectra. Conjoint optical and thermal ...

2009-10-19

164

Investigation of lauric acid dopant as a novel carbon source in MgB{sub 2} wire  

Energy Technology Data Exchange (ETDEWEB)

We fabricated lauric acid (LA) doped MgB{sub 2} wires and investigated the effects of the LA doping. For the fabrication of the LA-doped MgB{sub 2} wires, B powder was mixed with LA at 0-5 wt.% of the total amount of MgB{sub 2} using an organic solvent, dried, and then the LA-treated B and Mg powders were mixed stoichiometrically. The powder mixture was loaded into an Fe tube and the assemblage was drawn and sintered at 900 deg. C for 3 h under an argon atmosphere. We observed that the LA doping induced the substitution of C for the B sites in MgB{sub 2} and that the actual content of C increased monotonically with increasing LA doping level. The LA-doped MgB{sub 2} wires exhibited a lower critical temperature (T{sub c}), but better critical current density (J{sub c}) behavior in a high magnetic field: the 5 wt.% LA-doped sample had a J{sub ...

2010-11-01

165

Effects of initial microstructure and helium production on radiation hardening in F82H Steels  

International Nuclear Information System (INIS)

Full text of publication follows: Fission neutron irradiation to steels doped with isotope boron-10 is frequently conducted to study effects of the helium production on mechanical properties. The intrinsic mechanical properties of F82H steels could have been changed due to the boron doping. Recently, we reported that co-doping with boron and nitrogen to F82H (F82H+B+N) improved the mechanical properties of F82H doped only with boron. The mechanical properties of F82H+B+N are successfully comparable with the non-doped F82H before irradiation. In order to evaluate the effects of initial microstructure and helium production on radiation hardening, F82H and F82H+B+N were irradiate d Specimens used in this study were standard F82H martensitic steels, F82H steels doped with 60 mass ppm 10B and 200 ppm N (F82H+10B+N) and F82H steels doped with 60 ...

2007-12-10

166

Dielectric dispersion study of Mn-doped PLZT (8/65/35)  

International Nuclear Information System (INIS)

Mn-modified Pb0.92La0.08(Zr0.65Ti0.35)O3 (PLZT) was prepared chemically by a coprecipitate method using their respective nitrate salts and isopropoxides. Differential thermal analysis (DTA) and X-ray analysis clearly show the formation of PLZT single rhombohedral phase for samples calcined beyond 750 C. Uniform grain distribution was observed from scanning electron microscopic (SEM) studies and grain size was found to increase with Mn doping up to x=0.08 and then decreased. Dielectric measurement shows the decrease in peak transition temperature (TC) with Mn doping up to x=0.12 and then increase along with a sharp rise in dielectric maxima. A diffuse dielectric dispersion is observed in all the compositions. A detailed dispersion study was carried out using the Vogel-Fulcher empirical relation, a universal relaxation law and the Havriliak-Negami function. The Vogel-Fulcher relation fitting parameters of activation energy and freezing ...

2009-07-01

167

Zinc release from thapsigargin/IP3-sensitive stores in cultured cortical neurons  

UK PubMed Central (United Kingdom)

BackgroundChanges in ionic concentration have a fundamental effect on numerous physiological processes. For example, IP3-gated thapsigargin sensitive intracellular calcium...Full Text Available

168

Vectors containing a prokaryotic dihydrofolate reductase gene transform Drosophila cells to methotrexate-resistance.  

UK PubMed Central (United Kingdom)

Transformed Drosophila Kc cell lines, resistant to methotrexate, an inhibitor of de novo purine and pyrimidine synthesis, have been obtained by calcium phosphate transfection of plasmids containing...Full Text Available

1983-01-01

169

The opening of the two pores of the Hv1 voltage-gated proton channel is tuned by cooperativity  

UK PubMed Central (United Kingdom)

SUMMARYIn voltage-gated sodium, potassium, and calcium channels the functions of ion conduction and voltage sensing are performed by two distinct structural units: the pore domain...Full Text Available

2010-01-01

170

The nucleation kinetics of calcium sulfate dihydrate in NaCl solutions up to 6 m and 90 C  

Energy Technology Data Exchange (ETDEWEB)

The crystallization of calcium sulfate from aqueous solutions with NaCl is both geological and industrial interest because NaCl is the dominant solute in natural brines and many industrial fluids. Induction periods for the nucleation of calcium sulfate dihydrate were experimentally determined as a function of supersaturation in NaCl solutions from 0 to 6 m at 25 C and in 3.0-m NaCl solutions at temperatures from 25 to 90 C. Using classic nucleation theory, the interfacial tension between gypsum and 3.0-m NaCl solution was estimated to be about 39 mJ/m[sup 2] at 25 C and increases with increasing temperature (to 63 mJ/m[sup 2] at 90 C). It was observed that the induction period decreases with increasing NaCl concentrations up to 3 m and then starts to increase slightly at a given temperature and saturation state. The electrolyte effect on nucleation was proportional to the enhanced solubility of calcium sulfate dihydrate in ...

1994-02-01

171

The L-type calcium channel inhibitor diltiazem prevents cardiomyopathy in a mouse model  

UK PubMed Central (United Kingdom)

Dominant mutations in sarcomere protein genes cause hypertrophic cardiomyopathy, an inherited human disorder with increased ventricular wall thickness, myocyte hypertrophy, and disarray. To understand...Full Text Available

2002-04-15

172

Studies on Inhibition of Intestinal Absorption of Radioactive Strontium  

UK PubMed Central (United Kingdom)

A method is reported which permits selective suppression of absorption of radioactive strontium from ingested food material, permitting the calcium to be available to the body. Studies were carried...Full Text Available

1964-08-08

173

Strength and fluoride release characteristics of a calcium fluoride based dental nanocomposite  

UK PubMed Central (United Kingdom)

Secondary caries and restoration fracture remain the two most common problems in restorative dentistry. Release of fluoride ions (F) could be a substantial benefit because F could enrich neighboring...Full Text Available

2008-11-01

174

Severe Hypocalcemia due to Vitamin D Deficiency after Extended Roux-en-Y Gastric Bypass  

UK PubMed Central (United Kingdom)

Vitamin D deficiency is a well-known comorbidity of obesity that can be exacerbated after bariatric surgery and can predispose the patient for hypocalcemia. Vitamin D and calcium doses to prevent and...Full Text Available

2011-01-01

175

Role of Calcium in Serine Transport into Tobacco Cells  

UK PubMed Central (United Kingdom)

The transport of serine into tobacco (Nicotiana tabacum L. var. Xanthi) cells grown in liquid medium was studied. Serine transport was maximal below pH 4.0. A time-dependent stimulation...Full Text Available

1978-12-01

176

Resistance of Bacillus subtilis var. niger Spores Occluded in Water-insoluble Crystals to Three Sterilization Agents  

UK PubMed Central (United Kingdom)

The resistance to destruction of spores of Bacillus subtilis var. niger occluded in crystals of calcium carbonate and exposed to ethylene oxide and moist and dry heat...Full Text Available

1967-07-01

177

Regulation of Vacuolar H+-Pyrophosphatase by Free Calcium 1  

UK PubMed Central (United Kingdom)

The H+-translocating inorganic pyrophosphatase (H+-PPase) associated with vesicles of the vacuolar membrane (tonoplast) isolated from beet (Beta vulgaris L.) is...Full Text Available

1992-12-01

178

Regulation of Calcium Influx in Chara1  

UK PubMed Central (United Kingdom)

Measurements were made of 45Ca influx into isolated internodal cells of Chara corallina and also into internodal cells of intact plants. 45Ca influx was closely...Full Text Available

1992-10-01

179

Rapid Action of Estrogens on Intracellular Calcium Oscillations in Primate Luteinizing Hormone-Releasing Hormone-1 Neurons  

UK PubMed Central (United Kingdom)

Feedback controls of estrogen in LHRH-1 neurons play a pivotal role in reproductive function. However, the mechanism of estrogen action in LHRH-1 neurons is still unclear. In the present study, the...Full Text Available

2008-03-01

180

Radionuclide X-ray fluorescence analysis of waste water from the production of citric acid  

Energy Technology Data Exchange (ETDEWEB)

Radionuclide X-ray fluorescence analysis was used for the determination of iron, calcium, potassium, copper, manganese and zinc in waste water from the production process of citric acid.

1982-02-18

181

Radionuclide X-ray fluorescence analysis of waste water from the production of citric acid  

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence analysis was used for the determination of iron, calcium, potassium, copper, manganese and zinc in waste water from the production process of citric acid. (author).

1982-02-01

182

Propagation of an alkaline wave with a short contact time through an argilite sample from the Meuse-Haute Marne underground laboratory; Propagation d'une onde alcaline a temps de contact court a travers un echantillon d'argilite de l'est  

Energy Technology Data Exchange (ETDEWEB)

In the framework of the feasibility study of radioactive waste disposal in deep geologic formations, a clay formation (named 'argilite de l'Est') has been selected in the Meuse-Haute Marne region (France) for the construction of an underground laboratory. The percolation of alkaline solutions through the argilite has been studied using column experiments with short residence times (30 min). These experiments simulate the leaching of a cement which could be used in the building materials of the laboratory. The alkaline solutions used are mono-cationic solutions of calcium, sodium and strontium. The behaviour of calcium is differentiated from the other cations. For all alkaline solutions (NaOH, Ca(OH){sub 2} or Sr(OH){sub 2}) chemical reactions consuming both hydroxide ions and their associated cations have been evidenced. These reactions are heterogenous reactions of surface adsorption by site ionization. The ...

2001-07-01

183

Process for the removal of sulfur oxides from exhaust gases using slurry of red mud containing calcium ion  

Energy Technology Data Exchange (ETDEWEB)

A process is given for the removal of sulfur oxides from exhaust gases by absorbing with a slurry of red mud containing calcium ion which comprises the steps of: (1) contacting an exhaust gas containing sulfur oxides of not higher than about 100/sup 0/ C with a slurry of red mud containing calcium ion led from the next step (2) to take up sulfur oxides in the gas until ph of the slurry becomes in the range of 4.3 to less than 6 while maintaining the molar fraction of SO/sub 4/-- to total SO/sub 2/ in the slurry within the said pH range at 0.05 to 0.7; and then, (2) contacting the treated gas with a fresh slurry of red mud containing calcium ion to further take up sulfur oxides in the gas while maintaining the concentration of NaHSO/sub 3/ in the slurry at not more than about 8 g/l.

1980-09-16

184

Physiological calcium concentrations regulate calmodulin binding and catalysis of adenylyl cyclase exotoxins  

UK PubMed Central (United Kingdom)

Edema factor (EF) and CyaA are calmodulin (CaM)-activated adenylyl cyclase exotoxins involved in the pathogenesis of anthrax and whooping cough, respectively. Using spectroscopic, enzyme kinetic and...Full Text Available

2002-12-16

185

Neurobehavioral effects of power-frequency electromagnetic fields.  

UK PubMed Central (United Kingdom)

Some laboratory experiments have suggested that power-frequency electric and magnetic fields (EMF) may be capable of influencing calcium efflux from cell membranes, pineal function, and circadian rhythms....Full Text Available

1993-12-01

186

Intra- and extracellular calcium modulates stereocilia stiffness on chick cochlear hair cells.  

UK PubMed Central (United Kingdom)

Segments of the chick basilar papilla were isolated and maintained in culture medium. The sensory hair bundle of individual hair cells was observed with light microscopy and stimulated with a water...Full Text Available

1994-02-01

187

Imaging of calcium transients in skeletal muscle fibers.  

UK PubMed Central (United Kingdom)

Epifluorescence images of Ca2+ transients elicited by electrical stimulation of single skeletal muscle fibers were studied with fast imaging techniques that take advantage of the large fluorescence...Full Text Available

1991-01-01

188

Hysteretic Behavior of Proprotein Convertase 1/3 (PC1/3)  

UK PubMed Central (United Kingdom)

The proprotein convertases (PCs) are calcium-dependent proteases responsible for processing precursor proteins into their active forms in eukariotes. The PC1/3 is a pivotal enzyme of this family that...Full Text Available

189

Hydrogenolysis reaction of deashed coal loaded K and Ca. K to Ca wo tanjishita dakkai sekitan no suisoka bunkai tokusei  

Energy Technology Data Exchange (ETDEWEB)

Taiheiyo coal deashed using acid treatment and loaded with potassium or calcium was hydro-cracked under gaseous phase to discuss effects of these metals on liquefaction reaction. In addition, the loaded coal was added with red mud catalyst to examine effects of the addition. The loaded potassium has a softening power, and particularly the potassium adsorbed into surface and micropores in the coal decomposes selectively HI-BS and BI-PS and generates gas and HS. On the other hand, potassium deposited on coal surface promotes direct gas production from the coal. Irrespective of its loading modes, calcium has a catalytic nature to produce HI-BS selectively. Calcium also acts to impede decomposition of HI-BS into HS. Adding red mud catalyst to potassium loaded coal increases the inversion rate and the liquefaction yield, and most of the increase is accounted for by HI -BS, and BI-PS. When red mud catalyst is added to ...

1992-11-05

190

Gynura procumbens Merr. decreases blood pressure in rats by vasodilatation via inhibition of calcium channels  

UK PubMed Central (United Kingdom)

INTRODUCTION:Gynura procumbens has been shown to decrease blood pressure via inhibition of the angiotensin‐converting enzyme. However, other mechanisms that...Full Text Available

2011-01-01

191

Effects of Prolonged High Phosphorus Diet on Phosphorus and Calcium Balance in Rats  

UK PubMed Central (United Kingdom)

The amount of phosphorus contained in food as food additives is currently increasing and a high intake of phosphorus can cause various diseases. To determine the effects of a prolonged high phosphorus...Full Text Available

2007-05-01

192

Effect of Anionic Salt and Highly Fermentable Carbohydrate Supplementations on Urine pH and on Experimentally Induced Hypocalcaemia in Cows  

UK PubMed Central (United Kingdom)

The objective of this experiment was to determine the effect of dietary grain on calcium homeostasis. Six rumen-fistulated dairy cows with 3 or more previous lactations and no history of parturient...Full Text Available

2004-01-01

193

Disulfide Bonds and the Quaternary Structure of Factor VIII/von Willebrand Factor  

UK PubMed Central (United Kingdom)

Human Factor VIII/von Willebrand factor, purified by calcium citrate-cellulose chromatography and 4% agarose gel filtration was subjected to sodium dodecyl sulfate gel electrophoresis on gels containing...Full Text Available

1978-09-01

194

Dietary Ammonium Chloride for the Acidification of Mouse Urine  

UK PubMed Central (United Kingdom)

A novel therapeutic compound was found to induce bladder tumors in male rats. Given the location of the tumors and the increased amounts of calcium- and magnesium-containing solids found in the urine...Full Text Available

2009-03-01

195

Cytoplasmic Calcium Increases in Response to Changes in the Gravity Vector in Hypocotyls and Petioles of Arabidopsis Seedlings1  

UK PubMed Central (United Kingdom)

Plants respond to a large variety of environmental signals, including changes in the gravity vector (gravistimulation). In Arabidopsis (Arabidopsis thaliana) seedlings, gravistimulation...Full Text Available

2008-02-01

196

Citrat og nyresten  

DEFF Research Database (Denmark)

Citrate is an important naturally occurring inhibitor of calcium stone formation in urine. Urinary citrate excretion was examined in 43 consecutive patients with recurrent idiopathic calcium nephrolithiasis and in 50 normal controls by a specific enzymatic technique. Hypocitraturia (<1.6 mmol/24h) was found in 14 (33%) stone formers compared to 6 (12%) normal controls (p = 0.03). Citrate excretion expressed as citrate-creatinine ratio in 24 hour urine samples was significantly lower in the stone formers than in the healthy controls (p = 0.03), and significantly lower in healthy men, compared to healthy females (p = 0.006). There was a great variability in urinary citrate levels in both groups, and a considerable overlap in the urinary citrate excretion between normal subjects and stone formers. Factors other than urinary citrate excretion must therefore be of importance in the pathophysiology of calcium stone formation. ...

1993-01-01

197

Chemical neutralization to control denting in nuclear steam generators  

International Nuclear Information System (INIS)

Laboratory testing at Combustion Engineering has indicated promise in controlling simulated steam generator tube denting through chemical neutralization. Testing was limited to on-line treatment, and two neutralizers have been evaluated: calcium hydroxide and boric acid. On-line treatment with calcium hydroxide successfully halted active denting whenever the bulk calcium concentration (in ppm) equaled or exceeded the bulk chloride concentration (in ppm). Calcium hydroxide also was effective as an alternative to ammonia as a pH controlling agent in two tests conducted without ingress of chloride. On-line treatment with boric acid consisted of a four-day soak at simulated low (approximately 30 percent) power with 50 ppm B followed by one month full-power operation with 10 ppm B. This treatment also halted denting. Nondestructive and destructive examination of test boilers gave no indication of adverse ...

198

Case series of maxillary sinus augmentation with biphasic calcium phosphate: a clinical and radiographic study  

UK PubMed Central (United Kingdom)

PurposeThe aim of this study was to evaluate 3.5 years-cumulative survival rate of implants placed on augmented sinus using Osteon, a bone graft material, and to assess the height...Full Text Available

2011-04-01

199

Calcium/Calmodulin-Dependent Protein Kinase II Mediates Hippocampal Glutamatergic Plasticity During Benzodiazepine Withdrawal  

UK PubMed Central (United Kingdom)

Benzodiazepine withdrawal anxiety is associated with potentiation of α-amino-3-hydroxy-5-methyl-4-isoxazolepropionate receptor (AMPAR) currents in hippocampal CA1 pyramidal...Full Text Available

2010-08-01

200

Calcium gradients and buffers in bovine chromaffin cells.  

UK PubMed Central (United Kingdom)

1. Digital imaging and photometry were used in conjunction with the fluorescent Ca2+ indicator, Fura-2, to examine intracellular Ca2+ signals produced by depolarization of single adrenal chromaffin...Full Text Available

1992-05-01

201

Calcium Effects on Stomatal Movement in Commelina communis L. 1  

UK PubMed Central (United Kingdom)

Stomatal movements depend on both ion influx and efflux; attainment of steady state apertures reflects modulation of either or both processes. The role of Ca2+ in those two processes was...Full Text Available

1988-07-01

202

Cadherin Mechanics and Complexation: The Importance of Calcium Binding  

UK PubMed Central (United Kingdom)

E-cadherins belong to a family of membrane-bound, cellular adhesion proteins. Their adhesive properties mainly involve the two N-terminal extracellular domains (EC1 and EC2). The junctions between these...Full Text Available

2005-12-01

203

Amyloid Oligomer Neurotoxicity, Calcium Dysregulation, and Lipid Rafts  

UK PubMed Central (United Kingdom)

Amyloid proteins constitute a chemically heterogeneous group of proteins, which share some biophysical and biological characteristics, the principal of which are the high propensity to acquire an incorrect...Full Text Available

204

Age-dependent changes in Ca2+ homeostasis in peripheral neurones: implications for changes in function  

UK PubMed Central (United Kingdom)

Calcium ions represent universal second messengers within neuronal cells integrating multiple cellular functions, such as release of neurotransmitters, gene expression, proliferation, excitability,...Full Text Available

2007-06-01

205

Acetylsalicylic acid as soluble tablets  

International Science & Technology Center (ISTC)

Realization of Pharmacological Tests, Development of the Specifications and Technical Documentation and Registration in the Russian Federation of Medical Products as Soluble Tablets of Acetylsalicylic Acid/Calcium Carbonate in Two Dosages Intended for use as Medical Products Smoothing, Febrifugal and Antiaggregation Action and Development of Technology of Tableting the Above-Stated Preparations

206

A new method to measure necrotic core and calcium content in coronary plaques using intravascular ultrasound radiofrequency-based analysis  

UK PubMed Central (United Kingdom)

Although previous intravascular ultrasound (IVUS) radiofrequency-based analysis data showed acceptable reproducibility for plaque composition, measurements are not easily obtained, particularly that...Full Text Available

2010-04-01

207

A mathematical/physiological model of parathyroid hormone secretion in response to blood-ionized calcium lowering in vivo.  

DEFF Research Database (Denmark)

The aim of the present study was to test a mathematical model of the biochemical processes in the parathyroid glands responsible for the secretion of parathyroid hormone resulting from extracellular calcium reduction. A double exponential curve described the parathyroid hormone secretion induced by rapid lowering of blood-ionized calcium in humans with normal as well as abnormal parathyroid tissue. Our data show that it was possible to establish a simple mathematical model of the parathyroid hormone response to blood-ionized calcium lowering, sufficient to fit experimental data obtained from patients with abnormal and normal parathyroid tissue. The fitted parameters showed no significant differences between patients with insulin-dependent diabetes mellitus and controls. In primary hyperparathyroidism, the parathyroid hormone production and steady-state transport across the cell membrane were increased, probably due to the ...

1997-01-01

208

A Kinetic Model of Dopamine- and Calcium-Dependent Striatal Synaptic Plasticity  

UK PubMed Central (United Kingdom)

Corticostriatal synapse plasticity of medium spiny neurons is regulated by glutamate input from the cortex and dopamine input from the substantia nigra. While cortical stimulation alone results in long-term...Full Text Available

2010-02-01

209

* NASA TECHNICAL TRANSLATION NASA TT F-11435 INFLUENCE OF ...  

Science.gov (United States)

isotherme, dans un courant d'azote ou sous vide entretenu. I t. Comptes Rendus Scientific Academy, Paris, Vol. 265 pyrolyse du carbonate de calcium, ...

210

Magnetic susceptibility of Cesub(x)Lasub(1-x)B_6, Cesub(x)Eusub(1-x)B_6, Smsub(x)Lasub(1-x)B_6, and Smsub(x)Cesub(1-x)B_6 solid solutions  

International Nuclear Information System (INIS)

The magnetic susceptibility chi of Cesub(x)Lasub(1-x)B_6, Cesub(x)Eusub(1-x)B_6, Smsub(x)Lasub(1-x)B_6, and Smsub(x)Cesub(1-x)B_6 is investigated for temperatures of 80 to 1000 K. chi of Cesub(x)Lasub(1-x)B_6 and Cesub(x)Eusub(1-x)B_6 obeys the Curie-Weiss law. The composition dependence of effectiv magnetic moment #mu#sub(eff) exhibits an unusual behaviour. The value of #mu#sub(eff) per cerium ion abruptly decreases on substituting the cerium ions in CeB_6 by lanthanium ions. The values of the Weiss constants agree with the conclusions of the RKKY theory of indirect exchange by conduction electrons. The temperature dependence of chi of Smsub(x)Lasub(1-x)B_6 and Smsub(x)Cesub(1-x)B_6 do not obey the Curie-Weiss law. Both magnetic and X-ray data show that in Smsub(x)Lasub(1-x)B_6 and Smsub(x)Cesub(1-x)B_6 solid solutions the relative concentration of Sm"2"+ and Sm"3"+ ions changes with the change of composition. (author).

1980-11-01

211

Formation and reaction activity of CeO{sub 2} nanoparticles of cubic structure and various shaped CeO{sub 2}-TiO{sub 2} composite nanostructures  

Energy Technology Data Exchange (ETDEWEB)

Mono-dispersed cubic CeO{sub 2} nanoparticles have been synthesized using a surfactant-assisted method with laurylamine hydrochloride and cerium alkoxide modified with acetylacetone in an aqueous solution system. The prepared cubic CeO{sub 2} nanoparticles had a highly crystallized structure at 353 K and formed rod-like structures by calcination at 673 K after freeze-drying the CeO{sub 2} gel. We discovered a clear potential to make 1D, 2D or 3D CeO{sub 2}-materials with a well-controlled characteristic length and shape by assembling cubic-shaped CeO{sub 2} nanoparticle building blocks. CeO{sub 2}-TiO{sub 2} composite nanostructures have also been synthesized by changing the mole ratio of cerium alkoxide/titanium alkoxides. By utilizing the redox characteristic of CeO{sub 2}, CeO{sub 2} nanoparticles and CeO{sub 2}-TiO{sub 2} composite nanostructures after calcination, showed reaction activity toward the oxidization of I{sup -} to I{sub 2}, due ...

2007-07-15

212

Enhanced oxygen storage capacity of cerium oxides in CeO sub 2 /La sub 2 O sub 3 /Al sub 2 O sub 3 containing precious metals  

Energy Technology Data Exchange (ETDEWEB)

Effects of the addition of precious metals (PM; Pt, Rh) on CeO{sub 2}/Al{sub 2}O{sub 3} and CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} were confirmed to enhance the oxygen storage capacities (OSC). Increments in the OSC of the added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} catalysts were much greater than those in the OSC of the PM added CeO{sub 2}/Al{sub 2}O{sub 3}. The enhanced OSC is ascribed to the interaction between PM and a CeO{sub 2}-La{sub 2}O{sub 3} solid solution formed during the catalyst preparation. No enhancements in the OSC were observed on physical mixing of CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} and Pt-Rh/Al{sub 2}O{sub 3}, although the composition ratio of PM:CeO{sub 2}:La{sub 2}O{sub 3} is the same as that in the PM added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3}. This indicates that the intimate contacts between the precious metals and CeO{sub 2} particles dispersed on Al{sub 2}O{sub 3} are essential for the enhanced OSC of ...

1990-08-09

213

Yttrium Calcium Oxyborate for high average power frequency doubling and OPCPA  

Science.gov (United States)

Significant progress has been achieved recently in the growth of Yttrium Calcium Oxyborate (YCOB) crystals. Boules have been grown capable of producing large aperture nonlinear crystal plates suitable for high average power frequency conversion or optical parametric chirped pulse amplification (OPCPA). With a large aperture (5.5 cm x 8.5 cm) YCOB crystal we have demonstrated a record 227 W of 523.5nm light (22.7 J/pulse, 10 Hz, 14 ns). We have also demonstrated the applicability of YCOB for 1053 nm OPCPA.

2006-06-20

214

The early days of parathyroid surgery.  

Science.gov (United States)

The parathyroid endocrine glands, usually four in number and about the size of a split pea, lie on either side of the posterior aspect of the thyroid gland. Occasionally one or more of these structures are found in an aberrant position in the neck or even in the superior mediastinum. The parathyroid secretion, parathormone, regulates the level of serum calcium within sharply defined limits. Lack of parathormone, with lowering of the serum calcium, results in hyper-irritability of skeletal muscle, the clinical condition known as tetany. This is encountered following inadvertent removal or bruising of the parathyroid glands at thyroidectomy. PMID:21488463

2011-03-01

215

Stabilisation of #alpha#-Sialons using multiple additives  

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

1998-09-28

216

Physical aspects of FGD by-products  

Energy Technology Data Exchange (ETDEWEB)

Air pollution constraints continue to intensify, resulting in solid waste volume increases. An example of this is coal burning power plant flue gas desulfurization by scrubbing. The aqueous suspensions of calcium sulfate hemihydrate or calcium sulfate dihydrate will exceed 200 million tons annually by the year 2000. Disposal of these wastes can have massive environmental effects, due to physical instability and leaching to groundwater. One alternate disposal technique is sulfopozzolanic fixation, converting the FGD waste by addition of fine coal ash and an alkaline earth additive, into a monolithic mass. 6 refs., 17 figs., 3 tabs.

1992-01-01

217

New coumarin-based sensor molecule for magnesium and calcium ions  

British Library Electronic Table of Contents (United Kingdom)

A new coumarin-based sensor molecule (L1) has been synthesized and this was found to bind calcium and magnesium ions more effectively as compared to other alkali/alkaline earth/lanthanide and certain transition metal ions. A significant enhancement in fluorescence intensity was observed on binding to Ca2+ and Mg2+ ions; while a minor quenching was observed for weakly bound Hg2+, Ni2+, Fe3+, and Co2+ ions. PET process, coupled with the ICT process, is proposed to explain the observed spectral response.

2009-01-01

218

Method of producing calcium sulfate semihydrate in conjunction with the desulfurization of flue gases  

Energy Technology Data Exchange (ETDEWEB)

Calcium sulfate dihydrate in large crystal form is produced by maintaining the circulation of the lime containing scrubbing solution in the desulfurization scrubbing of flue gases from a power plant boiler so that it has a residence time of 5 to 25 hours, preferably 15 hours. The crystals are moved by passing a portion of the recirculation through a thinner in which a sludge containing crystals with a mean particle size of which 90% is in excess of 100 microns is removed. This product can be dewatered and treated with sulfuric acid and steam to convert it to the alpha semihydrate and is free from sulfite.

1985-03-05

219

Influence of microalloying on the corrosion resistance of steel in saturated calcium hydroxide  

International Nuclear Information System (INIS)

The influence of microalloying vanadium or titanium on improving the corrosion resistance of mild steel in saturated calcium hydroxide solution was investigated. Potential-time, potentiodynamic polarization, and impedance measurement techniques were employed. The corrosion products have been examined by infrared and X-ray diffraction analysis and by scanning electron microscopy. It has been shown that the grain refining, due to microalloying, plays an important role in enhancing the corrosion resistance of steel. Scales of calcite and iron oxides on top of a protective oxide are formed on the investigated steels.

220

Heat storage composition  

Energy Technology Data Exchange (ETDEWEB)

A heat storage compostion comprises sodium sulfate decahydrate as main component, a supercooling inhibitor, and a solid-liquid separation inhibitor. The composition is characterized in that hydraulic calcium sulfate and/or calcium sulfate dihydrate is contained as the solid-liquid separation inhibitor in an amount of 2-15 wt% base on the whole weight of the composition, whereby the solid-liquid separation, i.e. the sedimentation of the anhydrous sodium sulfate during the phase transition, is effectively prevented and the long-term stability is improved. The long-term stabilty of the composition can be more improved by addition of a silcia series of thickener.

1987-05-05

221

Exact solution to NO/sub 2/ absorption  

Energy Technology Data Exchange (ETDEWEB)

This paper describes an exact solution to the problem of absorbing nitrogen dioxide into aqueous solution, in which case the nitrogen dioxide concentration is allowed to vary over a wide range. The authors have worked on the rate of calcium sulfate dihydrate scale formation on the reverse osmosis membrane and find this phenomena can be treated by the crystallization theory. The authors performed long-term experiments using calcium sulfate dihydrate solution with addition of sodium hexametaphosphate (SHMP) and commercially available organophosphates and investigated the mechanism of the inhibitor's action quantitatively.

1984-04-01

222

Visible light photocatalytic activity and Photoelectrochemical property of Fe-doped TiO2 hollow spheres by sol?gel method  

British Library Electronic Table of Contents (United Kingdom)

Fe-doped TiO2 hollow spheres (Fe-THs) were synthesized by sol?gel process using carbon spheres as templates. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV?vis diffuse reflectance spectrum (DRS), N2 adsorption?desorption isotherms, Electron paramagnetic resonance (EPR) spectroscopy and Photoluminescence emission spectroscopy (PL). UV?vis spectra showed that Fe3+ doping could extend the absorption edge to the visible region. EPR spectra showed that Fe3+ was incorporated into the crystal lattice of TiO2, which could inhibit the recombination of photo-induced electron?hole pairs and improve the photocatalytic activity. The photocatalytic activities of the prepared samples were evaluated for the degradation of dye Reactive Brillia...

2011-01-01

223

Thermoluminescence studies in lead doped KCl and KBr crystals  

International Nuclear Information System (INIS)

Lead is known to enter substitutionally in divalent state when doped in alkali halides. When irradiated at room temperature these lead centers (Pb"+"+) act as traps for electrons knocked off from the halogen ions and become Pb"+ and Pb"0 (for large doses of irradiation). These changes could be followed in the optical absorption studies. These lead-doped crystals after X-ray irradiation yield a thermoluminescence output smaller than that observed in 'pure' crystals. However, two new glow peaks are observed in additions to those due to F-centers. In KCl : Pb and Kbr : Pb crystals part of the F-center glow preceds the new glow peaks. The new peaks are attributed to the Pb"+ and Pb"0 centers. The glow peak temperatures and trap depths for these peaks an obtained by total-curve fitting method are reported. (author).

1975-02-12

224

Synthesis and characterization of undoped and TM (Co, Mn) doped ZnO nanoparticles  

British Library Electronic Table of Contents (United Kingdom)

Antibacterial activity of Transition metals (Mn, Co) doped ZnO nanopowders prepared by a DC thermal plasma method against Escherichia coli and Staphylococcus aureus are investigated. The phase and morphology studies have been carried out by X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) respectively. All the samples of the present investigation are found to have hexagonal wurtzite structure and crystallite sizes are found to vary from 25nm to 30nm. Our bacteriological study showed the enhanced antibacterial activity of transition metals doped ZnO nanoparticles than undoped ZnO indicating the great potential of ZnO nanoparticles in relevant clinical and biomedical applications.

2011-01-01

225

Silicon oxide conductivity of hydrogen ion implanted polysilicon thin film transistors  

Energy Technology Data Exchange (ETDEWEB)

The influence of hydrogen ion implantation into the channel polysilicon of polysilicon thin film transistors on gate oxide conductivity has been investigated. Data for effective tunnelling barriers at the gate oxide/channel polysilicon interface are presented. A value of 1.2eV for samples with boron doped channel polysilicon is calculated. For hydrogenated boron doped samples tunnelling barriers higher than 2.1 eV are obtained. The tunnelling barriers for phosphorus doped samples are impurity concentration dependent and decrease with increasing phosphorus concentration in the range 3 x 10{sup 17} to 3 x 10{sup 19} cm{sup -3}. (Author).

1996-10-01

226

Silicon oxide conductivity of hydrogen ion implanted polysilicon thin film transistors  

International Nuclear Information System (INIS)

The influence of hydrogen ion implantation into the channel polysilicon of polysilicon thin film transistors on gate oxide conductivity has been investigated. Data for effective tunnelling barriers at the gate oxide/channel polysilicon interface are presented. A value of 1.2eV for samples with boron doped channel polysilicon is calculated. For hydrogenated boron doped samples tunnelling barriers higher than 2.1 eV are obtained. The tunnelling barriers for phosphorus doped samples are impurity concentration dependent and decrease with increasing phosphorus concentration in the range 3 x 10"1"7 to 3 x 10"1"9 cm"-"3. (Author).

227

Screen-printed Emitter-Wrap-Through solar cell with single step side selective emitter with 18.8% efficiency  

British Library Electronic Table of Contents (United Kingdom)

Abstract A fabrication process for Emitter-Wrap-Through solar cells on monocrystalline material with high quality gap passivation by wet thermal silicon dioxide is investigated. Masking and structuring steps are performed by screen-printing technology. Via-holes are created by an industrially applicable high-speed laser drilling process. The cell structure features a selective emitter structure fabricated in a single high temperature step: a highly doped emitter at the via-holes and the rear side, allowing for a low via-hole resistivity as well as a low resistivity contact to screen-printed pastes, and a moderately doped front side emitter exhibiting high quantum efficiency in the low wavelength range. Therefore a novel approach is applied depositing either doped or undoped PECVD silicon d...

2011-01-01

228

Luminescence spectroscopy of Er3+-doped and Er3+, Yb3+-codoped LaPO4 single crystals  

International Nuclear Information System (INIS)

LaPO4 single crystals lightly doped with Er3+, and codoped with Er3+ and Yb3+ have been grown by spontaneous nucleation in a lead phosphate flux. Absorption and luminescence spectra have been measured in the visible and near-IR regions and the excited state dynamics has been studied upon pulsed laser excitation. The obtained results have allowed the evaluation of the effective emission cross-sections around 1.5 ?m, that have been found to be similar to important oxide laser crystals doped with Er3+. Efficient visible upconversion has been observed upon excitation at 980 nm in the codoped crystals. This behaviour is attributed to Yb3+-Er3+ energy transfer processes.

2009-05-01

229

Influence of laser power on the properties of laser doped solar cells  

British Library Electronic Table of Contents (United Kingdom)

In recent years, increased attention has been focused on the use of lasers in different fabrication steps of solar cells, in particular laser doping to form emitter and/or selective emitter. In this method the laser energy is used to melt silicon, allowing the diffusion of dopant atoms to occur in the liquid phase. The main advantage of this method is the localised nature of the laser beam, which melts and diffuses a limited area without heating the bulk, therefore reducing the possible degradation associated with high temperature processes. At the University of New South Wales a novel laser doping method was developed, which combines the formation of the selective emitter with a self-aligned metallisation pattern. Despite achieving high efficiencies, concerns arose regarding the adhesion ...

2011-01-01

230

Impedance spectroscopy study with H-doped ammonium uranylphosphate self supported membranes  

Energy Technology Data Exchange (ETDEWEB)

Equivalent circuit and electrical parameters for H-doped NH{sub 4}UO{sub 2}PO{sub 4}.3H{sub 2}O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).

1995-01-01

231

Application of neutron transmutation doping method to initially p-type silicon material  

Energy Technology Data Exchange (ETDEWEB)

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x10{sup 19} n {omega} cm{sup -1}. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual {sup 32}P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially p-type silicon ingot was established.

2009-07-15

232

Application of neutron transmutation doping method to initially p-type silicon material  

International Nuclear Information System (INIS)

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x1019 n ? cm-1. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual 32P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially p-type silicon ingot was established.

2008-05-12

233

A novel electrogenerated chemiluminescence sensor for pyrogallol with core-shell luminol-doped silica nanoparticles modified electrode by the self-assembled technique  

British Library Electronic Table of Contents (United Kingdom)

The core-shell luminol-doped SiO2 nanoparticles were synthesized and immobilized on the surface of chitosan film coating graphite electrode by the self-assembled technique. Then, a novel electrogenerated chemiluminescence (ECL) sensor for pyrogallol was developed based on its ECL enhancing effect for the core-shell luminol-doped silica nanoparticles. The ECL analytical performances and the sensing mechanism of this ECL sensor for pyrogallol were investigated in detail. The corresponding results showed that: compared with the conventional ECL reaction procedures by luminol ECL reaction system, the electrochemical (EC) reaction of pyrogallol and its subsequent chemiluminescence (CL) reaction occurred in the different spatial region whilst offering a high efficiency to couple the EC with the ...

2006-01-01

234

Stable p-channel polysilicon thin film transistors fabricated by laser doping technique  

Energy Technology Data Exchange (ETDEWEB)

In this work we present the electrical characterization of non self-aligned p-channel thin film transistors fabricated by using laser doping technique for source/drain contact formation and gate oxide deposited at room temperature by Electron Cyclotron Resonance Plasma Enhanced Chemical Vapour Deposition. These techniques are suitable for a very low temperature process for TFT fabrication. The output characteristics show a current increase at high drain voltage ('kink' effect) rather moderate, if compared to self aligned polysilicon TFTs, probably due to the gradual doping profile induced by laser doping process. After bias stress at low gate voltage and high drain voltage condition a strong reduction of kink current has been observed in the output characteristics at high drain voltage, whereas minor changes has been observed in the transfer characteristics. This behaviour is similar to what observed in ...

2005-09-01

235

Stable p-channel polysilicon thin film transistors fabricated by laser doping technique  

International Nuclear Information System (INIS)

In this work we present the electrical characterization of non self-aligned p-channel thin film transistors fabricated by using laser doping technique for source/drain contact formation and gate oxide deposited at room temperature by Electron Cyclotron Resonance Plasma Enhanced Chemical Vapour Deposition. These techniques are suitable for a very low temperature process for TFT fabrication. The output characteristics show a current increase at high drain voltage ('kink' effect) rather moderate, if compared to self aligned polysilicon TFTs, probably due to the gradual doping profile induced by laser doping process. After bias stress at low gate voltage and high drain voltage condition a strong reduction of kink current has been observed in the output characteristics at high drain voltage, whereas minor changes has been observed in the transfer characteristics. This behaviour is similar to what observed in n-channel Gate ...

2005-09-01

236

Solid state and materials research: metal-semiconductor interactions  

International Nuclear Information System (INIS)

This section of the report is concerned with the study of the metallisation, oxidation and doping of materials which are of importance to the micro-electronics industry. The Van de Graaff accelerator and radioactive tracers are used for studying surface and sub-surface behaviour of these materials.

237

Self-organization of nickel atoms in silicon  

British Library Electronic Table of Contents (United Kingdom)

We present experimental evidence for self-organization of nickel microparticles in silicon under certain thermodynamic conditions of nickel diffusion doping. The concentration and distribution of the microparticles in silicon are very uniform. Additional anneals lead to self-ordering of the impurity microparticles.

2011-01-01

238

Preparation of nanostructure Ni doped CdO thin films by sol gel spin coating method  

British Library Electronic Table of Contents (United Kingdom)

The nanostructure Ni-doped CdO films have been prepared by sol gel spin coating method. Atomic force microscopy results indicate that the CdO films are formed from the nanoparticles and the grain size is changed with nickel content. X-ray diffraction patterns of the films indicate that the undoped and Ni-doped CdO films have polycrystalline structure with a cubic sodium chloride structure, showing two main characteristic peaks assigned to the (111) and (200) planes. The optical band gap values of undoped and Ni-doped CdO films were determined by optical absorption method. The Eg values of the CdO films were found to be in the range of 2.26?2.60?eV. The Eg values of the CdO films increase with the content of Ni dopant (up to 6% Ni). It is evaluated that the optical band gap and grain size o...

2011-01-01

239

Preparation and characterization of Co-doped BaTiO{sub 3} nanosized powders and ceramics  

Energy Technology Data Exchange (ETDEWEB)

The Co-doped BaTiO{sub 3} nanosized powders and ceramics were prepared via the sol-gel process. The powders and ceramics were characterized by methods of XRD, SEM and TEM. The dielectric properties of the ceramics were also determined by these methods. The influence of sintering temperature, sintering time and Co concentration on the microstructure and dielectric properties was discussed. The results revealed that the powders were in nanometer scale (30-50 nm) and were mainly composed of cubic BaTiO{sub 3} phase and small amount of BaCO{sub 3}. After sintering, both the cubic BaTiO{sub 3} and BaCO{sub 3} were transformed into tetrahedron BaTiO{sub 3}. The sintering temperatures of the Co-doped BaTiO{sub 3} ceramics decreased (about 100 deg. C) and the Curie temperatures of the ceramics were then moved to lower temperature. In addition, the dielectric constant of the ceramics doping with Co was higher than that of the pure ...

2006-08-25

240

Effect of dysprosium doping on the optical properties of SrS:Dy,Cl phosphor  

International Nuclear Information System (INIS)

The fundamental optical properties of dysprosium (Dy) doped strontium sulfide bulk samples for various dopant concentrations from 0.1 to 1.0 at.% were investigated by X-ray diffraction (XRD), electron paramagnetic resonance spectroscopy (EPR), room temperature photoluminescence (PL), photoluminescence excitation (PLE) and diffuse reflectance spectroscopy (DRS). Investigations by electron paramagnetic resonance yielded the state of Dy in the sample as Dy3+. An additional ESR line due to F+ center was observed. The PL emission spectrum consisted of several intense lines and a number of weaker ones which were identified as transitions between energy levels of Dy3+. The optimum doping concentration for maximum intensity was found to be 0.25 at.%. Blue shift of the absorption edge energy and red shift of the PLE spectrum were observed with increasing doping concentration. The former is due to Burstein-Moss (BM) effect and the ...

2010-08-13

241

Effect of boron doping in the carbon support on platinum nanoparticles and carbon corrosion  

Energy Technology Data Exchange (ETDEWEB)

Carbon supported catalysts can lose their activity over a period of time due to the sintering of the nanometer-sized catalyst particles. The sintering of metal clusters on carbon supports can occur due to the weak interaction between the metal and the support and also due to the corrosion of carbon, especially in fuel cell electrocatalysts. The sintering may be reduced by increasing the interaction between the metal and the support and also by increasing the corrosion resistance of carbon supports. In an effort to mitigate the growth of the nanoparticles, carbon-substituted boron defects were introduced in the carbon lattice. The interaction between the Pt nanoparticles on the pure and boron-doped carbon supports was examined using X-ray photoelectron spectroscopy (XPS). The results indicate that the interaction between the Pt nanoparticles and the boron-doped carbon support was slightly stronger than the interaction between the Pt ...

2009-07-15

242

Effect of Li-Al co-doping on the energy gaps of MgB2  

International Nuclear Information System (INIS)

We studied the effects of co-doping with Li and Al on the energy gaps of MgB2 by performing point-contact Andreev-reflection spectroscopy (PCAR) in polycrystalline Mg1-x(Al?Li1-?)xB2 samples with x?0.4. Even though the lattice parameters and the critical temperature of the compound simply scale with the effective Al content ?x, irrespective of the Li concentration, the energy gaps do not. In particular, for a given effective Al content, the comparison with Mg1-y(Al)yB2 with y = ?x shows that the ? bandgap is practically the same while the ? bandgap is higher. A clear gap merging is observed in the most doped sample (x = 0.4) when Tc<20 K. The results are discussed within the two-band Eliashberg theory and compared to the outcomes of first-principles calculations of the effects of Li and Al co-doping on the electronic structure of magnesium diboride.

2009-02-01

243

Boron transient enhanced diffusion in heavily phosphorus doped silicon  

Energy Technology Data Exchange (ETDEWEB)

A study has been made of B transient enhanced diffusion (TED) in heavily P-doped Si using secondary ion mass spectroscopy (SIMS) and positron annihilation spectroscopy (PAS). The P-doped silicon was implanted with boron ions of 40 keV energy to a dose of 3 {times} 10{sup 14} cm{sup {minus}2}, and then annealed at temperatures ranging from 700--1,000 C in a N{sub 2} ambient for varying durations. As P doping concentration increased from 3 {times} 10{sup 19} to 1 {times} 10{sup 20} cm{sup {minus}3}, boron diffusivity and the immobile boron fraction decreased. The experimental results are inconsistent with the predictions of the Fermi-level model and suggest that the clustering between B atoms and Si interstitials should be invoked in order to explain the immobile portion of the B peak during TED.

1997-11-01

244

Unitizations of double-ring structure and Erbium-doped waveguide amplifier for stable and tunable fiber laser  

British Library Electronic Table of Contents (United Kingdom)

We propose and demonstrate experimentally a singlelongitudinal-mode (SLM) fiber double-ring laser using an Erbium-doped waveguide amplifier (EDWA), polarization controller (PC), and a fiber Fabry-Perot tunable filter (FFP-TF) into the ring cavity. In addition, the output power, side-mode suppression ratio (SMSR), and the stabilities of power and wavelength of the laser also are investigated. (Copyright 2007 by Astro Ltd., Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA)

2007-01-01

245

Ultrashallow P{sup +}/N junction formation by plasma ion implantation  

Energy Technology Data Exchange (ETDEWEB)

We investigated the electrical characteristics and the junction depth of ultra-shallow junctions formed by using the plasma-doping method. Compared with ultra-low energy boron-ion implantation at 500 eV, the junctions formed with the plasma-doping process exhibited shallow junction depths and low sheet resistances. The junction depths of the plasma-doped samples were 150 A and 330 A after annealing for 10 s at 900 .deg. C and 950 .deg. C, respectively. For the same junction depth, the sheet resistance of the B{sub 2}H{sub 6} plasma-doped sample was an order of magnitude less than that of the 500-eV B-ion implanted sample. Cross-sectional transmission electron microscopy and deep level transient spectroscopy showed that the defects formed by the B{sub 2}H{sub 6} plasma-doping process could be removed by annealing at 950 .deg. C for 10 s. The scaling of metal-oxide-semiconductor ...

2000-12-01

246

Ultrashallow P"+/N junction formation by plasma ion implantation  

International Nuclear Information System (INIS)

We investigated the electrical characteristics and the junction depth of ultra-shallow junctions formed by using the plasma-doping method. Compared with ultra-low energy boron-ion implantation at 500 eV, the junctions formed with the plasma-doping process exhibited shallow junction depths and low sheet resistances. The junction depths of the plasma-doped samples were 150 A and 330 A after annealing for 10 s at 900 .deg. C and 950 .deg. C, respectively. For the same junction depth, the sheet resistance of the B_2H_6 plasma-doped sample was an order of magnitude less than that of the 500-eV B-ion implanted sample. Cross-sectional transmission electron microscopy and deep level transient spectroscopy showed that the defects formed by the B_2H_6 plasma-doping process could be removed by annealing at 950 .deg. C for 10 s. The scaling of metal-oxide-semiconductor field-effect-transistor ...

2000-12-01

247

Real time neutron diffraction study on the reaction of AsF/sub 5/ with deuterated polyparaphenylene  

Energy Technology Data Exchange (ETDEWEB)

The doping of deuterated polyparaphenylene (C/sub 6/D/sub 4/)sub(n) with AsF/sub 5/ has been investigated by real time neutron diffractometry at 100, 400 and 820 mbar AsF/sub 5/ pressure. The reaction appears to be diffusion controlled. Evidence for one doped phase with partial crystalline order was obtained. Structural considerations suggest two polymer chains plus one dopant ''string'' as the repetitive unit.

1982-07-01

248

Method of forming solar cells by grid contact isolation  

Energy Technology Data Exchange (ETDEWEB)

A solar cell structure is produced by a method comprising baking the solar cell, containing a gridded top layer of cuprous sulfide formed on a base of cadmium sulfide, for 20 minutes to 10 hours, to produce a copper doped cds electrically insulating region in the cadmium sulfide base near the interface of the cuprous sulfide and the cadmium sulfide; removing the cuprous sulfide, and the copper doped cds insulating region not covered by the grid, to provide a bare cadmium sulfide areas; and then forming a cuprous sulfide layer on the exposed areas not covered by the grid.

1982-03-16

249

Luminescent lanthanide-ion doped nanoparticles as single-biomolecule labels and oxidant sensors  

Science.gov (United States)

We report on the single-particle properties of lanthanide-ion doped oxide nanoparticles. We have demonstrated that their size can be accurately determined from their luminosity. The optically determined size distribution is in very good agreement with the distribution obtained from transmission electron microscopy (TEM). We also showed that the photobleaching of these nanoparticles is related to a reduction process and that we can use it to sense in a concentration-dependent manner the presence of an oxidant like H2O2. Finally, we propose a way to perform nanoparticle-protein coupling and to determine the protein-nanoparticle ratio at the single-particle level.

2007-02-01

250

Investigation of new materials for SOFC applications; Untersuchungen zum Einsatz neuer Werkstoffe fuer SOFC-Anwendungen  

Energy Technology Data Exchange (ETDEWEB)

Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The ...

2007-05-04

251

Helium atom doping of molybdenum and its influence on the radiation hardenings  

International Nuclear Information System (INIS)

Experimental results on study of helium concentration influence on degree of molybdenum radiation hardening for various method of cyclotron doping differing in degree and damage character are presented. It is established that accumulation of helium atoms in molybdenum for simultaneous formation of radiation defects caused by low energetic primary-knocked atoms leads to higher degree of hardening than for high energetic ion irradiation. It is shown that with increase of helium atom concentration the degree of radiation hardening for the same level of damage increases. 4 refs.; 3 figs. (author).

1990-05-22

252

Fluorescence resonance energy transfer using lanthanide-ion doped oxide nanoparticles as donors  

Science.gov (United States)

We have demonstrated fluorescence resonance energy transfer (FRET) between lanthanide-ion doped oxide nanoparticles acting as donors and organic acceptor molecules (Cy5). Due to the long nanoparticle lifetime and the large Stokes shift between nanoparticle absorption and emission, unambiguous and precise FRET measurements can be performed despite the presence of large free acceptor oncentrations. We determined FRET efficiencies as a function of Cy5 concentration which are in very good agreement with a multiple acceptor-multiple donor calculation.

2006-03-01

253

Optimizing the specific surface area of fly ash-based sorbents for flue gas desulfurization.  

Science.gov (United States)

High performance sorbents for flue gas desulfurization can be synthesized by hydration of coal fly ash, calcium sulfate, and calcium oxide. In general, higher desulfurization activity correlates with higher sorbent surface area. Consequently, a major aim in sorbent synthesis is to maximize the sorbent surface area by optimizing the hydration conditions. This work presents an integrated modeling and optimization approach to sorbent synthesis based on statistical experimental design and two artificial intelligence techniques: neural network and genetic algorithm. In the first step of the approach, the main and interactive effects of three hydration variables on sorbent surface area were evaluated using a full factorial design. The hydration variables of interest to this study were hydration time, amount of coal fly ash, and amount of calcium sulfate and the levels investigated were 4-32 h, 5-15 g, and 0-12 g, respectively. In ...

2005-07-05

254

Gastrointestinal absorption of lead (/sup 203/Pb) in chicks: influence of lead, calcium, and age  

Energy Technology Data Exchange (ETDEWEB)

The present study was designed to investigate, in more detail, the mechanism of lead transport by the gastrointestinal tract and particularly the similarities or dissimilarities between lead and calcium in this process. The absorption of these metals was determined in 3-week-old white Leghorn cockerels, raised on a commercial diet or special diets, using an in vivo ligated loop procedure. The dose administered into the loop usually contained 0.5 ..mu..Ci /sup 203/Pb (and/or 0.1 ..mu..Ci /sup 47/Ca), 0.01 mM lead acetate (and/or 1 mM CaCl/sub 2/) in 0.5 ml of 0.15 M NaCl, pH 6.5. It was shown that lead is rapidly taken up by the intestinal tissue, and only slowly transferred into the circulation whereas calcium, also accumulated rapidly by the tissue, is rapidly released from the tissue in the serosal direction. The absorption processes of these cations show similar responses to various experimental conditions (low calcium ...

1981-10-01

255

Contribution of calcium ions and hydrogen ions to the signal transduction chain in phytochrome-mediated spore germination. [Onoclea sensibilis L  

Energy Technology Data Exchange (ETDEWEB)

Red light stimulates germination in the spores of Onoclea sensibilis L. Phytochrome is confirmed to be the photoreceptor pigment in the germination response by demonstrating red-far-red photoreversibility. External Ca/sup 2 +/ is required for this response with a threshold at a submicromolar concentration. Red light stimulates an increase in the total concentration of intracellular calcium in the spores as determined by atomic absorption spectroscopy. Subsequent exposure to far-red light inhibits the red light-induced increase in intracellular calcium. The majority of the increase occurs 5 minutes after the onset of irradiation. The calcium-antagonist, La/sup 3 +/ inhibits both germination and the red light-induced increase in intracellular calcium. Using /sup 31/P-nuclear magnetic resonance spectroscopy, the author tested the hypothesis that a sustained increase in intracellular pH contributes to the ...

1985-01-01

256

Transfer of chemical elements to breast milk; Transfer von Elementen in die Muttermilch  

Energy Technology Data Exchange (ETDEWEB)

The project is intended to yield information on the transfer factors describing the transfer of ingested radionuclides to breast milk for the following elements: antimony, cerium, chromium, cobalt, gallium, lanthanum, molybdenum, niobium, radium, ruthenium, silver, thorium, titanium, and uranium. Those yet unknown or poorly known transfer factors are required in order to be able to develop a reliable model for description and assessment of the transfer of the radionuclides and the possibly resulting hazardous doses to infants, and for subsequent formulation of recommendations for radiological protection of the population. (orig./CB) [German] Ziel des Projektes ist die Ermittlung von Transferfaktoren fuer den Uebergang von Radionukliden aus der Nahrung der Muetter in die Muttermilch fuer die Elemente Antimon, Cer, Chrom, Cobalt, Gallium, Lanthan, Molybdaen, Niob, Radium, Ruthenium, Silber, Thorium, Titan und Uran. Um die Exposition und damit die moegliche Gefaehrung ...

1999-08-01

257

The ternary system cerium-palladium-silicon  

Science.gov (United States)

Phase relations in the ternary system Ce-Pd-Si have been established for the isothermal section at 800 deg. C based on X-ray powder diffraction and EMPA techniques on about 130 alloys, which were prepared by arc-melting under argon or powder reaction sintering. Eighteen ternary compounds have been observed to participate in the phase equilibria at 800 deg. C. Atom order was determined by direct methods from X-ray single-crystal counter data for the crystal structures of tau{sub 8}-Ce{sub 3}Pd{sub 4}Si{sub 4} (U{sub 3}Ni{sub 4}Si{sub 4}-type, Immm; a=0.41618(1), b=0.42640(1), c=2.45744(7) nm), tau{sub 16}-Ce{sub 2}Pd{sub 14}Si (own structure type, P4/nmm; a=0.88832(2), c=0.69600(2) nm) and also for tau{sub 18}-CePd{sub 1-x}Si{sub x} (x=0.07; FeB-type, Pnma; a=0.74422(5), b=0.45548(3), c=0.58569(4) nm). Rietveld refinements established the atom arrangement in the structures of tau{sub 5}-Ce{sub 3}PdSi{sub 3} (Ba{sub 3}Al{sub 2}Ge{sub 2}-type, Immm; a=0.41207(1), b=0.43026(1), ...

2009-09-15

258

The ternary system cerium-palladium-silicon  

British Library Electronic Table of Contents (United Kingdom)

Phase relations in the ternary system Ce-Pd-Si have been established for the isothermal section at 800degreeC based on X-ray powder diffraction and EMPA techniques on about 130 alloys, which were prepared by arc-melting under argon or powder reaction sintering. Eighteen ternary compounds have been observed to participate in the phase equilibria at 800degreeC. Atom order was determined by direct methods from X-ray single-crystal counter data for the crystal structures of t8-Ce3Pd4Si4 (U3Ni4Si4-type, Immm; a=0.41618(1), b=0.42640(1), c=2.45744(7)nm), t16-Ce2Pd14Si (own structure type, P4/nmm; a=0.88832(2), c=0.69600(2)nm) and also for t18-CePd1-xSix (x=0.07; FeB-type, Pnma; a=0.74422(5), b=0.45548(3), c=0.58569(4)nm). Rietveld refinements established the atom arrangement in the structures of...

2009-01-01

259

The influence of the nature of the metal on the performance of cerium oxide supported catalysts in the partial oxidation of ethanol  

Energy Technology Data Exchange (ETDEWEB)

This work studied the effect of the nature of the metal on the performance of Co/CeO{sub 2}, Pd/CeO{sub 2} and Pt/CeO{sub 2} catalysts in the partial oxidation of ethanol. Infrared spectroscopy of adsorbed ethanol and temperature programmed desorption of ethanol were performed in order to establish the reaction mechanism. Catalytic experiments revealed that the product distribution is strongly affected by the nature of the metal. Acetaldehyde was practically the only product formed on a Co/CeO{sub 2} catalyst while methane was also produced on Pt/CeO{sub 2} and Pd/CeO{sub 2} catalysts. These results were explained through a reaction mechanism proposed by the characterization techniques. Co/CeO{sub 2} and Pt/CeO{sub 2} catalysts show mainly ethoxy species at room temperature whereas acetate species is mainly formed on the Pd/CeO{sub 2} catalyst. The ethoxy species can undergo further dehydrogenation and desorb as acetaldehyde. This effect is more significant with the Co/CeO{sub 2} ...

2005-12-01

260

Microwave dissolution of plant tissue and the subsequent determination of trace lanthanide and actinide elements by inductively coupled plasma-mass spectrometry  

Energy Technology Data Exchange (ETDEWEB)

Recently there has been much concern with the ability of plants to uptake heavy metals from their surroundings. With the development of instrumental techniques with low detection limits such as inductively coupled plasma-mass spectrometry (ICP-MS), attention is shifting toward achieving faster and more elegant ways of oxidizing the organic material inherent in environmental samples. Closed-vessel microwave dissolution was compared with conventional methods for the determination of concentrations of cerium, samarium, europium, terbium, uranium and thorium in a series of samples from the National Institute of Standards and Technology and from fields in Idaho. The ICP-MS technique exhibited detection limits in parts-per-trillion and linear calibration plots over three orders of magnitude for the elements under study. The results obtained by using nitric acid and hydrogen peroxide in a microwave digestion system for the analysis of reference materials showed close ...

1997-08-01

261

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio programme  

Energy Technology Data Exchange (ETDEWEB)

We provide a detailed overview of an on-going, multinational test programme that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolised materials plus volatilised fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy/density device. The programme participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research programme. Sandia National Laboratories has the lead role for conducting this research programme; test programme support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. We provide a summary of the overall, multiphase test design and a description of all explosive containment and aerosol collection ...

2004-07-01

262

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio programme  

International Nuclear Information System (INIS)

We provide a detailed overview of an on-going, multinational test programme that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolised materials plus volatilised fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy/density device. The programme participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research programme. Sandia National Laboratories has the lead role for conducting this research programme; test programme support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. We provide a summary of the overall, multiphase test design and a description of all explosive containment and aerosol collection ...

263

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio program.  

Energy Technology Data Exchange (ETDEWEB)

The authors provide a detailed overview of an on-going, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy-density device. The program participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research program. Sandia National Laboratories has the lead role for conducting this research program; test program support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. The authors provide a summary of the overall, multiphase test design and a description of all explosive containment and aerosol ...

2004-08-01

264

Initiation of depleted uranium oxide and spent fuel testing for the spent fuel sabotage aerosol ratio program  

International Nuclear Information System (INIS)

The authors provide a detailed overview of an on-going, multinational test program that is developing aerosol data for some spent fuel sabotage scenarios on spent fuel transport and storage casks. Experiments are being performed to quantify the aerosolized materials plus volatilized fission products generated from actual spent fuel and surrogate material test rods, due to impact by a high-energy-density device. The program participants in the United States plus Germany, France and the United Kingdom, part of the international Working Group for Sabotage Concerns of Transport and Storage Casks (WGSTSC) have strongly supported and coordinated this research program. Sandia National Laboratories has the lead role for conducting this research program; test program support is provided by both the US Department of Energy and the US Nuclear Regulatory Commission. The authors provide a summary of the overall, multiphase test design and a description of all explosive containment and aerosol ...

265

Crystal electric field excitations in the cerium compound CeRh{sub 3}B{sub 2} studied by inelastic neutron scattering  

Energy Technology Data Exchange (ETDEWEB)

We have performed inelastic neutron scattering (INS) experiments on CeRh{sub 3}B{sub 2} at various temperatures to obtain direct information on the crystal electric field (CEF) in this compound, which exhibits some very peculiar magnetic properties for a Ce system: it is ferromagnetic with an unusually high Curie temperature (115 K), which contrasts with a strongly reduced and anisotropic magnetization (0.4 {mu}{sub B}/fu within the c-plane of the hexagonal structure). Measurements with high incident energies show only one well defined magnetic excitation around 150 meV, its exact position varying with the temperature. These results, combined with our previous data of magnetization and magnetic form factor, have permitted us to determine the CEF energy level scheme taking into account the two J multiplets of the Ce{sup 3+} ion. Information on the ground state (quasielastic contribution and ground state moment) has also been obtained by experiments at low incident energies in the ...

2007-12-19

266

Crystal electric field excitations in the cerium compound CeRh_3B_2 studied by inelastic neutron scattering  

International Nuclear Information System (INIS)

We have performed inelastic neutron scattering (INS) experiments on CeRh_3B_2 at various temperatures to obtain direct information on the crystal electric field (CEF) in this compound, which exhibits some very peculiar magnetic properties for a Ce system: it is ferromagnetic with an unusually high Curie temperature (115 K), which contrasts with a strongly reduced and anisotropic magnetization (0.4 #mu#_B/fu within the c-plane of the hexagonal structure). Measurements with high incident energies show only one well defined magnetic excitation around 150 meV, its exact position varying with the temperature. These results, combined with our previous data of magnetization and magnetic form factor, have permitted us to determine the CEF energy level scheme taking into account the two J multiplets of the Ce"3"+ ion. Information on the ground state (quasielastic contribution and ground state moment) has also been obtained by experiments at low incident energies in the paramagnetic state.

2007-12-19

267

ESR study of X-ray irradiated rare earth (Ln) ion-doped glaserite and Ln ion-doped langbeinite  

Energy Technology Data Exchange (ETDEWEB)

X-ray irradiation-induced paramagnetic radicals in rare earth (Ln) ion-doped glaserite and Ln ion-doped langbeinite were studied by means of ESR technique, aiming at developing the highly sensitive sensor for an ESR dosimetry. The samples were prepared by two kinds of procedures as follows. In one process, the glaserite (K{sub 3}Na(SO{sub 4}){sub 2}) matrix or the langbeinite (K{sub 2}Mg{sub 2}(SO{sub 4}){sub 3}) matrix were synthesized by heating the mixture of K{sub 2}SO{sub 4} and Na{sub 2}SO{sub 4} or the mixture of K{sub 2}SO{sub 4} and MgSO{sub 4} at 1023 K for 1 hour in He flow. The matrices obtained were mixed well with a fixed amount of Ln{sub 2}(SO{sub 4}){sub 3} (Ln=La, Eu, Gd, Lu) powder and heated at 1023 K for 1 hour in He flow. In the other process, the homogeneous mixture of a fixed amount of K{sub 2}SO{sub 4}, Na{sub 2}SO{sub 4} and Ln{sub 2}(SO{sub 4}){sub 3} powders or a fixed amount of K{sub 2}SO{sub 4}, MgSO{sub 4} and ...

1992-06-01

268

The seeded growth of calcium sulfate dihydrate crystals in NaCl solutions up to 6 m and 90 C  

Energy Technology Data Exchange (ETDEWEB)

The kinetics of calcium sulfate crystal growth is of importance in various fields, such as geochemistry, desalination technology, petroleum industry, and water and wastewater treatment. The seeded crystal growth rate of calcium sulfate dihydrate was measured as a function of supersaturation in NaCl electrolyte solutions from 0 to 6 m at temperatures of 25, 50, 70, and 90 C. The growth followed a second-order parabolic rate law with activation energies greater than 53 kJ/mol which suggested the surface reaction as the rate-limiting step. It was observed that the rate constant and the activation energy are solution composition dependent. The rate constant increases with NaCl concentration up to 3 molal and then begins to fall slightly. The activation energy dropped from 61 kJ/mol in the pure Ca-SO[sub 4]H[sub 2]O system to 53 kJ/mol in 3.0 m NaCl solutions. The electrolyte effect was similar to the crystal solubility behavior in aqueous ...

1994-03-15

269

Role of HCl in adsorption of elemental mercury vapor by calcium-based sorbents. Report for September 1998--May 1999  

Energy Technology Data Exchange (ETDEWEB)

The paper gives results of a study to identify active sites and surface functional groups that may contribute to the absorption of elemental mercury (Hg) by relatively inexpensive calcium (Ca)-based sorbents. The study investigated the formation of chlorine (Cl) sites in CA-based sorbents as well as their role and reactivity in the absorption of Hg. HCl-exposed calcium sulfate dihydrate (gypsum) exhibited a superior Hg sorption capability. Crystalline water molecules on the surface of the gypsum were confirmed to contribute indirectly to Hg uptake. These surface molecules may have absorbed HC1 through hydrogen bond formation between an oxygen atom of a crystalline water molecule and a hydrogen atom of an HCl molecule. Two adjacent, physically absorbed HCl molecules could then trap an Hg molecule through formation of a mercuric-chloride-like molecule. Significant correlations between Cl and Hg uptake by gypsum were noted.

1999-11-01

270

Role of HCl in adsorption of elemental mercury vapor by calcium-based sorbents. Report for September 1998--May 1999  

Energy Technology Data Exchange (ETDEWEB)

The paper gives results of a study to identify active sites and surface functional groups that may contribute to the absorption of elemental mercury (Hg) by relatively inexpensive calcium (Ca)-based sorbents. The study investigated the formation of chlorine (Cl) sites in CA-based sorbents as well as their role and reactivity in the absorption of Hg. HCl-exposed calcium sulfate dihydrate (gypsum) exhibited a superior Hg sorption capability. Crystalline water molecules on the surface of the gypsum were confirmed to contribute indirectly to Hg uptake. These surface molecules may have absorbed HC1 through hydrogen bond formation between an oxygen atom of a crystalline water molecule and a hydrogen atom of an HCl molecule. Two adjacent, physically absorbed HCl molecules could then trap an Hg molecule through formation of a mercuric-chloride-like molecule. Significant correlations between Cl and Hg uptake by gypsum were noted.

1999-01-01

271

Inhibition of calmodulin - regulated calcium pump activity in rat brain by toxaphene  

Energy Technology Data Exchange (ETDEWEB)

In vivo effects of toxaphene on calcium pump activity in rat brain synaptosomes was studied. Male Sprague-Dawley rats were dosed with toxaphene at 0,25,50, and 100 mg/kg/day for 3 days and sacrificed 24 h after last dose. Ca/sup 2 +/-ATPase activity and /sup 45/Ca uptake were determined in brain P/sub 2/ fraction. Toxaphene inhibited both Ca/sup 2 +/-ATPase activity and /sup 45/Ca/sup 2 +/ uptake and the inhibition was dose dependent. Both substrate and Ca/sup 2 +/ activation kinetics of Ca/sup 2 +/-ATPase indicated non-competitive type of inhibition as evidenced by decreased catalytic velocity but not enzyme-substrate affinity. The inhibited Ca/sup 2 +/-ATPase activity and Ca/sup 2 +/ uptake were restored to normal level by exogenously added calmodulin which increased both velocity and affinity. The inhibition of Ca/sup 2 +/-ATPase activity and Ca/sup 2 +/ uptake and restoration by calmodulin suggests that toxaphene may impair active calcium ...

1986-03-05

272

Inhibition of calmodulin - regulated calcium pump activity in rat brain by toxaphene  

International Nuclear Information System (INIS)

In vivo effects of toxaphene on calcium pump activity in rat brain synaptosomes was studied. Male Sprague-Dawley rats were dosed with toxaphene at 0,25,50, and 100 mg/kg/day for 3 days and sacrificed 24 h after last dose. Ca"2"+-ATPase activity and "4"5Ca uptake were determined in brain P_2 fraction. Toxaphene inhibited both Ca"2"+-ATPase activity and "4"5Ca"2"+ uptake and the inhibition was dose dependent. Both substrate and Ca"2"+ activation kinetics of Ca"2"+-ATPase indicated non-competitive type of inhibition as evidenced by decreased catalytic velocity but not enzyme-substrate affinity. The inhibited Ca"2"+-ATPase activity and Ca"2"+ uptake were restored to normal level by exogenously added calmodulin which increased both velocity and affinity. The inhibition of Ca"2"+-ATPase activity and Ca"2"+ uptake and restoration by calmodulin suggests that toxaphene may impair active calcium transport mechanisms by decreasing regulator protein ...

1986-04-13

273

Experimental investigation on denting in PWR steam generators: causes and corrective actions  

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers where feedwater was polluted with sea or river water. Specific effects of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hrs for seawater pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water, denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid, or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high seawater pollution. Soaks cannot stop denting if they are not followed by an on-line ...

274

Experimental investigation on denting in PWR steam generators, causes and corrective actions  

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon-steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers, feedwater being polluted with sea or river water. Specific effect of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hours for sea-water pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high sea-water pollution. Soaks cannot stop denting if they are not followed by an on-line ...

1985-03-01

275

Crystallization fouling of calcium sulfate dihydrate on heat-transfer surfaces  

Energy Technology Data Exchange (ETDEWEB)

The present paper deals with the fouling process of calcium sulfate dehydrate on heat-transfer surfaces. The crystallization of calcium sulfate showed typical asymptotic fouling curves, the asymptotic value of which was greatly influenced by the surface temperature and fluid velocity. The fouling mechanism was discussed with a generalized fouling model and proved to be surface process controlled, where the activation energy was 6.2 {times} 10{sup 4} J/mol. The availability of mechanical cleaning against the formed scale was quantitatively evaluated by applying the particle abrasion method. The removal test verified that the removing rate per unit particle concentration decreased in an inverse proportion to the overall particle load, to the power of 0.8, and that it was affected by the fluid velocity. The observed final residual fouling resistance decreased asymptotically with an increase in particle concentration. The suitable concentration of ...

1996-02-01

276

Clear liquor scrubbing with anhydrite production. Fourth quarter 1996 technical progress report  

Energy Technology Data Exchange (ETDEWEB)

This project is part of PETC`s Advanced Power Systems Program, whose mission is to accelerate the commercialization of affordable, high- efficiency, low emission, coal-fueled electric generating technologies. A process concept - Clear Liquor Scrubbing with Anhydrite Production - was proposed and accepted by PETC as a Phase I project in its Mega-PRDA program. the project integrated three process operations - chloride control upstream of the flue gas desulfurization (FGD) system, a clear liquor process for enhanced SO{sub 2} removal performance, and production of anhydrite (anhydrous calcium sulfate) rather than calcium sulfite or gypsum (calcium sulfate dihydrate). The first step in the project was to perform batch and flow-through experiments in the laboratory to confirm theoretical calculations and preliminary laboratory results concerning anhydrite formation, these laboratory experiments were designed to prove that ...

1997-02-03

277

Calcium sulfate crystallization along citrus root channels in a Florida soil exhibiting acid sulfate properties  

Energy Technology Data Exchange (ETDEWEB)

The authors observed euhedral crystals in Manatee soil in a citrus grove in St. Lucie County, Florida. The material was identified as gypsum (CaSO/sub 4/ /times/ 2H/sub 2/O) using x-ray diffraction and infrared spectra. Photomicrography and scanning electron microscopy revealed that gypsum accumulated both in old root channels and within citrus root tissue of the Btg horizon. The subsurface horizons had elevated sulfate levels, a low initial pH, a drop (0.5 unit) in pH upon air-drying. Electrical conductivity paralleled the concentration of water-soluble sulfate. High levels of calcium and sulfate occurred for horizons above the water table. This accumulation is attributed to groundwater bearing these ions and subsequently discharging them to the overlying soil. Dead citrus roots appear to act as wicks to aid water transfer from lower to higher horizons. The roots and their empty channels provide spaces in which the gypsum can precipitate if the concentrations of ...

1988-02-01

278

An indicator, high speed method for determining the water and aqueous phase content in a hydrocarbon fuel  

Energy Technology Data Exchange (ETDEWEB)

A method and an instrument for determining the total water content in a hydrocarbon fuel using an indicator composition, which includes calcium hydride and phenolphthaleyn, are developed. The essence of the method is fixing the presence of water with its interaction with the calcium hydride and subsequent indication of the formed Ca(OH)2 using the phenolphthallen. To make the indicator composition, a hygroscopic cotton, prewashed by rectified alcohol and dried for 30 minutes at 105 degrees, is impregnated by a 1 percent alcohol solution of phenolphthaleyn and is dried in the same conditions. Then the cotton is processed by a powder form calcium hydride (a layer thickness of 0.1 to 0.2 millimeters, and a granule size of less than or equal to 80 micromters). The indicator composition is placed in a glass tube (a diameter of 4 to 7 millimeters and a length of 80 to 100 millimeters), whose ends are sealed or filled with ...

1983-01-01

279

Alternative calcium-sulfate-bearing materials as cement retarders: Part II. FGD gypsum  

Energy Technology Data Exchange (ETDEWEB)

The aim of this paper is to investigate the possible displacement of natural gypsum (CaSO{sub 4}2H{sub 2}O) in cement with an alternative setting retarder, such as the industrial by-product derived from flue gas desulfurization process called FGD gypsum. These calcium-sulfate-bearing materials (CSBM), alone or in mixtures, were ground with clinker both in laboratory and industrial scale to examine their influence on the physical and mechanical properties of cement, as well as on the industrial production line of cement. From the present work, it is extracted that the use of mixtures of sulfate-bearing materials with gypsum seems to be advantageous for the actual control of setting time. The addition of FGD gypsum increases setting time without affecting compressive strength profile. During the industrial trial, the formation of hemihydrate form of calcium sulfate dihydrate has a profound regulatory effect on the setting and strength performance ...

2004-11-01

280

Activation of fat cell adenylate cyclase by protein kinase C  

Energy Technology Data Exchange (ETDEWEB)

Purified protein kinase C (C-kinase) from guinea pig pancreas and rat brain stimulated adenylate cyclase activity in purified rat adipocyte membranes. Cyclase stimulation occurred over 100 to 1000 mU/ml of C-kinase activity, required greater than 10 ..mu..M calcium, proceeded without a lag, was not readily reversible, and required no exogenous phospholipid. Moreover, C-kinase inhibitors, such as chlorpromazine and palmitoyl carnitine, inhibited selectively adenylate cyclase which was activated by C-kinase and calcium. Depending on assay conditions, 10 nM 12-0-tetradecanoylphorbol-13-acetate (TPA) either enhanced or was required for kinase action on cyclase. Also, TPA plus calcium promoted the quantitative association of C-kinase with membranes. Adenylate cyclase activation by C-kinase was seen both in the presence and absence of exogenous GTP, indicating that the kinase effect does not result from an action on the ...

1986-05-01

281

Technical-economic aspects of the utilization of geothermal waters  

International Nuclear Information System (INIS)

A brief description is given of the physico-chemical parameters characterized a hot water geothermal reservoir and of its exploitation by means of single or coupled (doublet) wells. The technical aspects of geothermal heat to the users is then discussed, beginning with corrosion of materials caused by seven main agents: oxygen, hydrogen sulphide, carbon dioxide, ammonia, hydrogen, sulphates and chlorides. A brief mention is made of scaling due to calcium carbonate, silica and calcium sulphates. The basic components of a geothermal plant for non-electric uses are then discussed: production pumps, surface pipelines, heat exchangers, heat pumps and reinjection pumps. The advantages and disadvantages of the different equipment and materials used in the geothermal sector are also presented. A list is also given of the criteria used in the energy and economic balance of a geothermal operation. (author). 24 refs, 13 figs, 2 tabs.

282

Studies on the chemical composition and possible mechanisms underlying the antispasmodic and bronchodilatory activities of the essential oil of Artemisia maritima L.  

British Library Electronic Table of Contents (United Kingdom)

This study describes the chemical composition of the essential oil of Artemisia maritima (Am.Oil) and the pharmacological basis for its medicinal use in gut and airways disorders. Twenty five compounds, composing 93.7% of the oil, were identified; among these, chrysanthenyl propionate and elixene were identified for the first time from any Artemisia species. The Am.Oil (0.3?1.0 mg/mL) suppressed spontaneous and high K+ (80 mM)-induced contractions in isolated rabbit jejunum, suggestive of an antispasmodic effect mediated possibly through calcium channel blockade. The calcium channel blockade activity was confirmed when pre-treatment of the tissue with Am.Oil (0.01?0.03 mg/mL) shifted the Ca++ concentration-response curves to the right, similar to verapamil and papaverine. In isolated trach...

2011-01-01

283

Sterilization of male stray dogs with a single intratesticular injection of calcium chloride: a dose-dependent study  

British Library Electronic Table of Contents (United Kingdom)

ObjectiveTo study a method of chemical sterilization and its efficacy in adult male stray dogs.MethodsSterilization was performed 45 days after a single bilateral intratesticular injection of calcium chloride (CaCl2) at the doses of 5, 10, 15 or 20 mg per testis per kg body weight.ResultsHistomorphological measures of testes showed total necrosis of testicular tissue at 45 days after an injection of either 10 or 15 or 20 mg CaCl2 along with fibrosis and hyalinization in seminiferous tubules and interstitial spaces. Infiltration of leucocytes was also observed with the 10- or 15-mg dose. Disintegration of germ cell arrangement in seminiferous tubules and washing out of germ cells from the tubules were noted with the 5-mg dose. Relative organ weight, epididymal sperm count, plasma and intrat...

2007-01-01

284

Scale prevention with special reference to threshold treatment  

Energy Technology Data Exchange (ETDEWEB)

Various chemical, physical, and mechanical methods to prevent unwanted deposition of mineral scale are described. The suitability of the different methods, which largely depends on the specific features and requirements of the system involved, is discussed. Special emphasis is placed upon the threshold treatment, where the growth process is retarded by the addition of trace amounts of growth inhibitors. Growth experiments have been performed on barium sulfate and calcium sulfate dihydrate seed crystals, suspended in a supersaturated solution with and without organic bisphosphonates as inhibitors. Two methods are selected for the analysis of the growth data. A degree of inhibition is defined to obtain a quantitative description of the influence of a growth inhibitor on the growth rate of the crystals. In addition the influence of the molecular structure of various bisphosphonates with different substituents is shown. The effect of a bisphosphonate on the geometry of ...

1983-01-01

285

NEW SLAG-BASED CONCRETES  

Environmental Research Database

ObjectivesTo determine the reaction rate of slag during curing and factors affecting reactivity.~%~~%~To measure the rates of chloride ingress into concrete and the extent of chloride binding.~%~~%~To determine conditions for pitting corrosion and the nature of corrosion products.~%~~%~To characterise the reactions in slag-calcium alumina cement hydration and the nature of the products.~%~DescriptionBlast-furnace slag has latent hydraulic properties, giving considerable potential for commercial use in addition to its widespread use as a partial replacement for Portland cement, notably in alkali-activated slag (AAS) and slag-calcium alumina cement (CAC) concretes. Use of AAS concretes is already well-established in China and the former USSR, but their further application is hindered by lack of research into setting, hydration and durability, Slag/CAC blends are new materials whose chemistr ...

1999-01-09

286

Intermediate-conductance calcium-activated potassium channels participate in neurovascular coupling  

British Library Electronic Table of Contents (United Kingdom)

BACKGROUND AND PURPOSE Controlling vascular tone involves K+ efflux through endothelial cell small- and intermediate-conductance calcium-activated potassium channels (KCa2.3 and KCa3.1, respectively). We investigated the expression of these channels in astrocytes and the possibility that, by a similar mechanism, they might contribute to neurovascular coupling. EXPERIMENTAL APPROACH Transgenic mice expressing enhanced green fluorescent protein (eGFP) in astrocytes were used to assess KCa2.3 and KCa3.1 expression by immunohistochemistry and RT-PCR. KCa currents in eGFP-positive astrocytes were determined in situ using whole-cell patch clamp electrophysiology. The contribution of KCa3.1 to neurovascular coupling was investigated in pharmacological experiments using electrical field stimulatio...

2011-01-01

287

Interaction studies between Crofer-22APU alloy and P2O5 containing barium calcium alumino-borosilicate (BCABS) sealant glass-ceramics  

International Nuclear Information System (INIS)

We present the effect of P2O5 addition on barium calcium aluminum borosilicate BCABS glasses of composition (mol %) 35BaO-15CaO-5Al2O3-(37-x)SiO2-8B2O3-xP2O5 (0?x?5). The incorporation of P2O5 increased network polymerization and crystallization tendency. However, addition of P2O5 leads to the formation of Cr2O3 at the interface, saturating it in the ions of the metal. This improves glass-to-metal bonding. (author)

2010-09-01

288

Determination of some minor and trace elements in iron ores by ion exchange chromatography, spectrophotometry and atomic absorption spectrometry  

International Nuclear Information System (INIS)

A method is described for determination of aluminium, cadmium, cobalt, chromium, copper, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, zinc, titanium and vanadium in iron ore. After dissolution, a 1 gram sample of iron ore is applied to a column of AGI-X8 anion exchange resin (chloride form), in 100 ml of 7M HCl. Aluminium, chromium, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, titanium and vanadium are eluted with 7M HCl; iron, copper and cobalt are eluted with 0.5M HCl; cadmium and zinc are eluted with 2M HNO_3. Iron is subsequently removed from copper and cobalt by a solvent extraction with methyl isobutyl ketone. The elements are determined in the eluates by atomic absorption spectrometry, except for titanium and vanadium, which are determined spectrophotometrically.

289

Calcium phosphate glass-ceramics for bioactive coating on a #beta#-titanium alloy  

International Nuclear Information System (INIS)

The formation of a porous coating is the decisive feature for the bio-compatibility of silica-free calcium phosphate glass ceramics on alloy surfaces like the #beta#-Ti structured Ti-29Nb-13Ta-4.6Zr used in this work. The ceramic composition is highly important: 50CaO-40P_2O_5-7Na_2O-3TiO_2 glass powder produces a pore-free coating unable to bind hydroxyapatite, whereas 60CaO-30P_2O_5-7Na_2O-3TiO_2 glass incorporates pores from which a crystalline hydroxyapatite phase can grow over the surface from simulated body fluid (see Figure). (Abstract Copyright [2003], Wiley Periodicals, Inc.)

2003-07-01

290

Acid-site distribution on Faujasite-type zeolites determined by n-butylamine titration--1. Comparison of the use of hammett and arylmethanol indicators on zeolites X  

Energy Technology Data Exchange (ETDEWEB)

The combined Lewis and Broensted acidities were measured of 13X (sodium) zeolite and of its 84.2% calcium-exchanged, 86.0% lanthanum-exchanged, and 69.2% protonated forms, calcined at 400/sup 0/C. The butylamine titrations were performed to visible color changes of Hammett indicators. The H/sub 0/ acidities were 0 for the sodium X zeolite, and 0.2, 0.98, and 0.75 for the calcium, lanthanum, and hydrogen zeolites, respectively. These acidities compared well with trends reported in literature for zeolites pretreated under different conditions. Titration of Broensted sites with arylmethanol indicators did not give satisfactory visible endpoints.

1980-05-29

291

A prospective randomised open label study to evaluate the potential of a new silver alginate/carboxymethylcellulose antimicrobial wound dressing to promote wound healing  

British Library Electronic Table of Contents (United Kingdom)

The aim of this study was to observe both the clinical signs and symptoms of wounds at risk of infection, that is critically colonised (biofilm infected) and antimicrobial-performance of an ionic silver alginate/carboxymethylcellulose (SACMC) dressing, in comparison with a non silver calcium alginate fibre (AF) dressing, on chronic venous leg and pressure ulcers. Thirty-six patients with venous or pressure ulcers, considered clinically to be critically colonised (biofilm infected), were randomly chosen to receive either an SACMC dressing or a non silver calcium AF dressing. The efficacy of each wound dressing was evaluated over a 4-week period. The primary study endpoints were prevention of infection and progression to wound healing. The SACMC group showed a statistically significant (P = ...

2010-01-01

292

Point-contact Andreev-reflection spectroscopy in MgB{sub 2}: The role of substitutions  

Energy Technology Data Exchange (ETDEWEB)

We summarize the results of point-contact Andreev-reflection (PCAR) spectroscopy in MgB{sub 2} doped by chemical substitutions, either magnetic (Mn) or non-magnetic (Al,C), obtained by us and by other groups in the last four years. Despite the variety of samples used (crystals and polycrystals of various origin) and some minor differences in the experimental techniques, these measurements have directly provided a complete and consistent picture of the effects of chemical substitutions on the gaps of MgB{sub 2} shedding light on other relevant parameters (scattering rates, DOSs) affected by doping. In Al-doped crystals and polycrystals, the gap amplitudes {delta}{sub {sigma}} and {delta}{sub {pi}} - obtained through a two-band Blonder-Tinkham-Klapwijk (BTK) fit of the Andreev-reflection conductance curves - decrease on increasing the Al content x (i.e. on decreasing the critical temperature of the contacts T{sub c}{sup A}), ...

2007-06-01

293

Nonaqueous synthesis of metal oxide nanoparticles: Short review and doped titanium dioxide as case study for the preparation of transition metal-doped oxide nanoparticles  

Science.gov (United States)

The liquid-phase synthesis of metal oxide nanoparticles in organic solvents under exclusion of water is nowadays a well-established alternative to aqueous sol-gel chemistry. In this article, we highlight some of the advantages of these routes based on selected examples. The first part reviews some recent developments in the synthesis of ternary metal oxide nanoparticles by surfactant-free nonaqueous sol-gel routes, followed by the discussion of the morphology-controlled synthesis of lanthanum hydroxide nanoparticles, and the presentation of structural peculiarities of manganese oxide nanoparticles with an ordered Mn vacancy superstructure. These examples show that nonaqueous systems, on the one hand, allow the preparation of compositionally complex oxides, and, on the other hand, make use of the organic components (initially present or formed in situ) in the reaction mixture to tailor the morphology. Furthermore, obviously even the crystal structure can differ from the corresponding ...

2008-07-15

294

Magnetic and transport properties of Ba_2Co_9O_1_4 and Ba_1_._9A_0_._1Co_9O_1_4 (A=La or Na)  

International Nuclear Information System (INIS)

The valence and spin-state distributions of Co ions and the complex structure of antiferromagnetic Ba_2Co_9O_1_4 have led to the suggestion that doped Ba_2Co_9O_1_4 compounds may be good thermoelectric materials. We have checked this suggestion by measuring the magnetic properties as well as the transport properties of nominal Ba_1_._9A_0_._1Co_9O_1_4 (A=La or Na). We show that although all compounds are indicated to be single phase by powder X-ray diffraction analysis, they are all p-type polaronic conductors with low mobile-hole concentrations. Magnetic-susceptibility data of the parent and La-doped compounds give evidence of a second magnetic phase with ferromagnetic order setting in below 215 K; but this second phase is not seen in the Na-doped sample. We conclude that the structure is stabilized by oxidation and that cation exolution from the Ba_2Co_9O_1_4 structure creates cation vacancies that oxidize the high-spin ...

2010-11-01

295

Electronic properties of doped CuPc layers  

Energy Technology Data Exchange (ETDEWEB)

Doping of molecular organic materials is important for the functionality of organic electronic devices as e.g solar cells. We investigated the doping behaviour of the acceptor molecules Cl{sub 2}-DCNQI and F{sub 16}CuPc incorporated into a CuPc matrix. In-situ XPS/UPS measurements were performed on coevaporated films. Doping by Cl{sub 2}-DCNQI was not successful. The molecule lost its chlorine atoms during thermal evaporation. For pristine F{sub 16}CuPc layers we observe a strong broadening of the photoemission features with increasing deposition rate indicating different domains probably of different molecular structure of differing electric interface potential. F{sub 16}CuPc incorporated into CuPc shows sharp photoemission features. With increasing F{sub 16}CuPc content Fermi level shifts are observed in both phases. In CuPc the maximum shift is about 0.45 eV towards the HOMO level indicating ...

2009-07-01

296

White luminescence of Tm-Dy ions co-doped aluminoborosilicate glasses under UV light excitation  

International Nuclear Information System (INIS)

Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses were prepared in this study. The luminescence properties of the glasses were analyzed. A combination of blue, green, yellow, and red emission bands was shown for these glasses, and white light emission could be observed under UV light excitation. White light luminescence color could be changed by varying the excitation wavelength. Concentration quenching effect was investigated in this paper. Furthermore, the dependence of luminescence properties on glass compositions was studied. Results showed that the luminescence intensity changed with different network modifier oxides, while the white color luminescence was not affected significantly. - Graphical abstract: Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses, which emit white light under UV light excitation, were prepared. The dependence of luminescence properties on glass compositions was studied, and results showed that the white ...

2008-10-01

297

Transient enhanced diffusion of boron in silicon: The interstitial flux  

Energy Technology Data Exchange (ETDEWEB)

Delta-doped boron marker layers in silicon have been used to test further the relationship between B transient enhanced diffusion (TED) and the flux of silicon interstitials released during the annealing stage following self implantation. The authors present new data which address a number of questions raised by the present models. They show that in the experiments bulk trapping of interstitials is significant only for low implant fluences ({approximately}10{sup 12} cm{sup {minus}2}). The origin of the observed diffusion-like profiles for the interstitial flux is instead found to lie in local trapping within the {delta}-doped layers themselves. Boron trapped in immobile clusters may be associated with Si interstitials in approximately a 1:1 ratio; nevertheless this trapping contribution alone may not entirely account for the observed gradient. They suggest that some part of the observed TED response with depth is attributable to local trapping ...

1997-11-01

298

Transient enhanced diffusion of boron in silicon: The interstitial flux  

International Nuclear Information System (INIS)

Delta-doped boron marker layers in silicon have been used to test further the relationship between B transient enhanced diffusion (TED) and the flux of silicon interstitials released during the annealing stage following self implantation. The authors present new data which address a number of questions raised by the present models. They show that in the experiments bulk trapping of interstitials is significant only for low implant fluences (#approx#10"1"2 cm"-"2). The origin of the observed diffusion-like profiles for the interstitial flux is instead found to lie in local trapping within the #delta#-doped layers themselves. Boron trapped in immobile clusters may be associated with Si interstitials in approximately a 1:1 ratio; nevertheless this trapping contribution alone may not entirely account for the observed gradient. They suggest that some part of the observed TED response with depth is attributable to local trapping of silicon ...

1996-12-02

299

Synthesis and photoluminescence properties of Sm3+-doped LaMgB5O10 and GdMgB5O10  

International Nuclear Information System (INIS)

Luminescence and reflection spectra as well as luminescence kinetics of the 1 mol% Sm3+-doped crystalline lanthanum magnesium meta borate (LaMgB5O10) and gadolinium magnesium meta borate (GdMgB5O10) were analyzed. Materials were synthesized by conventional solid state route and showed bright orange-red emission under UV excitation. Emission spectra contain sharp and well resolved Sm3+4G5/2#->#6HJ transitions indicating a strong crystal-field effect. In case of gadolinium compound energy transfer between Gd3+ and Sm3+ was detected. The luminescent kinetics of the Sm3+ in analyzed powders is characterized by single exponential decay and experimental values vary in the range 2.2-2.4 ms. - Research highlights: ? Phosphorescence of samarium-doped lanthanide magnesium meta borates. ? Bright and well resolved orange-red emission of Sm3+ under UV excitation. ? Energy transfer from Gd3+ to Sm3+ in gadolinium magnesium meta borate is observed. ? The ...

2011-07-01

300

Surface Fermi level engineering: Or there's more to Schottky barriers than just making diodes and field effect transistor gates  

Science.gov (United States)

Surface scientists argue about the fundamental nature of Schottky barriers, or more precisely what determines the location of the Fermi level at semiconductor surfaces and interfaces. Electrical and materials engineers worry about how to make Schottky barrier diodes and gates to field effect transistors and the control of barrier heights. There is some interesting middle ground in which the location of the surface and interface Fermi level can, for example, determine semiconductor doping characteristics during crystal growth. The authors will discuss several interesting and well known examples of doping characteristics which are still somewhat mysterious. Specifically, they address the following question: (1) why is Ge doped GaAs p type when grown from Ga melts but n type when grown from Au melts (2) why is low resistivity p type ZnSe, AlAs, and AlGaInP hard to make, and more importantly, how can the problem be fixed. In ...

301

Structural and morphology studies of praseodymium-doped bismuth titanate prepared using a wet chemical route  

Energy Technology Data Exchange (ETDEWEB)

Praseodymium-doped Bi{sub 4}Ti{sub 3}O{sub 12} (BIT) with various compositions of dopant, Pr (x = 0.5, 0.6, 0.7, 0.8) in Bi{sub 4-x}Pr{sub x}Ti{sub 3}O{sub 12} (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800 deg. C exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x = 0.5) resulted in dramatically reduced of grain size from 2 {mu}m to less than 50 nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1 {mu}m was observed for x = 0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the addition of x = 0.50, and increasing with further addition of Pr. Dissipation factor (tan {delta}) ...

2009-05-05

302

Structural and morphology studies of praseodymium-doped bismuth titanate prepared using a wet chemical route  

International Nuclear Information System (INIS)

Praseodymium-doped Bi_4Ti_3O_1_2 (BIT) with various compositions of dopant, Pr (x = 0.5, 0.6, 0.7, 0.8) in Bi_4_-_xPr_xTi_3O_1_2 (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800 deg. C exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x = 0.5) resulted in dramatically reduced of grain size from 2 #mu#m to less than 50 nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1 #mu#m was observed for x = 0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the addition of x = 0.50, and increasing with further addition of Pr. Dissipation factor (tan #delta#) followed the same trend as ...

2009-05-05

303

Structural and morphology studies of praseodymium-doped bismuth titanate prepared using a wet chemical route  

British Library Electronic Table of Contents (United Kingdom)

Praseodymium-doped Bi4Ti3O12 (BIT) with various compositions of dopant, Pr (x=0.5, 0.6, 0.7, 0.8) in Bi4-xPrxTi3O12 (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800degreeC exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x=0.5) resulted in dramatically reduced of grain size from 2mm to less than 50nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1mm was observed for x=0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the ad...

2009-01-01

304

Single-crystal microwires based on doped Bi for anisotropic thermoelectric devices  

International Nuclear Information System (INIS)

We have investigated the possibility to use a microwire of BiSn to design an anisotropic thermoelectric generator. The glass-coated microwire of pure and Sn-doped bismuth was obtained by the Ulitovsky method; it was a cylindrical single-crystal with orientation (1011) along the wire axis; the C3 axis was inclined at an angle of 70 degrees to the microwire axis. It is found that doping of bismuth wires with tin increases the thermopower anisotropy in comparison with Bi by a factor of 2 - 3 in the temperature range of 200-300 K. For a Bi microwire with a core diameter of 10 ?m with a glass coating with outer diameter of 35 ?m, the transverse thermopower is ? 150 ?V/(K*cm); for BiSn, 300 ?V/(K*cm). The design of an anisotropic thermogenerator based on BiSn microwire is proposed. The miniature thermogenerator will be efficient for power supply of devices with low useful current. In addition to the considerable thermopower anisotropy of BiSn wires ...

2011-07-07

305

Quality Management for Neutron Transmutation Doping of Silicon Ingot in HANARO  

Energy Technology Data Exchange (ETDEWEB)

By using this doping method, silicon semiconductors with extremely uniform dopant distributions can be produced, and this is the dominant advantage of NTD compared with a conventional chemical doping. Good uniformity of a dopant concentration is usually required for high power applications such as thyristor (SCR), IGBT, IGCT and GTO and for special sensors. Achieving an accurate neutron fluence corresponding to a target resistivity as well as a uniform irradiation is the prime target of a neutron irradiation for NTD. Generally, in order to reach an accurate neutron fluence, a real time neutron flux is monitored by a neutron detector such as a Self-powered Neutron Detector(SPND). And, after an irradiation, the total irradiation fluence is confirmed by measuring the absolute activity of a neutron activation sample that has been irradiated with a silicon ingot, and thus the SPND can be properly calibrated. Excellent irradiation uniformity and a ...

2007-10-15

306

Preparation of Eu-doped #beta#- and 15R-SiAlONs by ammonia nitridation of the precursor obtained using aluminum glycine gel  

International Nuclear Information System (INIS)

Synthesis of Eu-doped #beta#- and 15R-SiAlONs was studied by the ammonia nitridation of precursors derived from an #alpha#-Si_3N_4 fine powder dispersed in aluminum glycine gel with various Si/Al ratio and post-annealing in a nitrogen pressure furnace. The largest amount of #beta#-SiAlON was observed in the product at 1750 deg. C for Si/Al = 1/1 with small amounts of both #alpha#- and 15R-SiAlON impurities. The product showed two emissions at around 420 nm and 560 nm. The emission intensities decreased with increasing amount of #beta#-SiAlON. The former and latter emissions were assigned to Eu"2"+ in the 15R- and #alpha#-SiAlONs impurities. A mixture of Eu-doped 15R-SiAlON with #alpha#-Al_2O_3 impurity was obtained for Si/Al = 1/6, using AlN together with Al(NO_3)_3.9H_2O in a 2/1 atomic ratio as the aluminum source. It showed a bluish-white emission at 450 nm under 254 nm radiation.

2009-11-13

307

Lithium intercalation in porous carbon electrodes  

Energy Technology Data Exchange (ETDEWEB)

Carbons derived from the phase separation of polyacrylonitrile/solvent mixtures were investigated as lithium intercalation anodes for rechargeable lithium-ion batteries. The carbon electrodes have a bulk density of 0.35-0.5 g/cm{sup 3}, relatively low surface areas (< 10 m{sup 2}/g), and micron-size cells. Pyrolysis temperature influences the reversible lithium intercalation and the irreversible capacity (associated with the formation of the passivating layer). Carbon electrodes pyrolyzed at 600{degrees}C have first-cycle capacity as high as 550 mAh/g as well as large irreversible capacity, 440 mAh/g. Electrodes prepared at 1050{degrees}C have reversible capacities around 270 mAh/g with relatively lower capacity losses (120 mAh/g). Doping the organic precursors with phosphoric acid, prior to pyrolysis at 1050{degrees}C, leads to carbon electrodes with reversible capacities as high as 450 mAh/g. The capacity of doped carbon increased with ...

1995-04-01

308

Carbon nanotube coating silicon doped with Cr as a high capacity anode  

Energy Technology Data Exchange (ETDEWEB)

Effects of dopant and coating carbon nanotube on anodic performance of Si were studied for metallic anode Li ion rechargeable battery with large capacity. Although the large Li intercalation capacity higher than 1500mAhg{sup -1} is exhibited on pure Si, it decreased drastically with increasing cycle number. Increasing the electrical conductivity by doping Cr or B is effective for increasing the initial capacity and the cycle stability of Si for Li intercalation. Coating semiconductive Si with the carbon nanotube by decomposition of hydrocarbon is effective for increasing the cycle stability, though the initial Li intercalation capacity slightly decreased. Conducting binder is also important for increasing the cycle stability and it was found that Li intercalation capacity higher than 1500mAhg{sup -1} can be sustained by using poly vinyliden fruolide. Consequently, reversible Li intercalation capacity of 1500mAhg{sup -1} was successfully sustained after 10th cycles ...

2005-08-26

309

Al[sub 0. 3]Ga[sub 0. 7]As/GaAs heterojunction tunnel diode for tandem solar cell applications  

Energy Technology Data Exchange (ETDEWEB)

A p[sup +]-Al[sub 0.3]Ga[sub 0.7]As/n[sup +]-GaAs heterojunction tunnel diode was fabricated using Atomic Layer Epitaxy (ALE) growth technique. Background carbon doping of [similar to]10[sup 20] cm[sup [minus]3] was achieved in the p-side of the diode by optimizing growth conditions such as V/III ratio, exposure times to reactant gases, and growth temperature. In the n-side of the diode GaAs was doped with silane and doping concentrations as high as 7[times]10[sup 18] cm[sup [minus]3] were also achieved. The dopants are chosen to satisfy the high levels and low diffusion requirements. The diode can be used to interconnect the high and low band-gap cells in the AlGaAs/GaAs cascade solar cell structure. The reactor used in this investigation is a commercial MOCVD system which has been specially modified for dual operation of ALE and MOCVD growth modes.

1994-06-30

310

VC- and Cr{sub 3}C{sub 2}-doped WC-NbC-Co hardmetals  

Energy Technology Data Exchange (ETDEWEB)

This study compares the microstructure and mechanical properties of plain and 0.9 or 3.6 wt% VC- or Cr{sub 3}C{sub 2}-doped WC-12 wt% Co hardmetals with 40 wt% NbC, prepared by pulsed electric current sintering (PECS) in the solid state for 4 min at 1240 deg. C and conventional pressureless liquid phase sintering (CS) for 1 h at 1420 deg. C. The addition of VC or Cr{sub 3}C{sub 2} was found to inhibit grain growth of the residual WC grains, whereas the size of the solid solution (Nb,W,V/Cr)C grains was hardly influenced. The type of grain growth inhibitor and densification temperature however, strongly influenced the composition of the NbC solid solution formed, which was thermodynamically and experimentally assessed.

2008-09-22

311

Up-conversion luminescence saturation under pulsed excitation of erbium-doped, SiO_2-TiO_2 sol-gel powders  

International Nuclear Information System (INIS)

The intensity of erbium up-conversion luminescence could be limited by a saturation effect due to increased pump power. We studied the luminescence saturation of the 550 nm emission on erbium-doped, SiO_2-TiO_2 sol-gel powders under pulsed excitation at 979 and 1532 nm. From the latter, the up-converted luminescence intensity decreased with increasing excitation power, whereas no saturation was observed at 979 nm excitation. We proposed that the saturation effect is determined by the pump power, the erbium content and the lifetime of the corresponding first excited states at different pumping schemes.

2010-12-01

312

Tunable erbium-doped fiber ring laser for applications of infrared absorption spectroscopy  

British Library Electronic Table of Contents (United Kingdom)

We fabricate a low noise erbium-doped fiber ring laser that can be continuously tuned over 102nm by insertion of the fiber Fabry-Perot tunable filter (FFP-TF) in the ring cavity with a novel cavity structure and the optimal gain medium length. As an application of this fiber ring laser, we performed the absorption spectroscopy of acetylene (13C2H2) and hydrogen cyanide (H13C14N) and measure the absorption spectra of more than 50 transition lines of these gases with an excellent signal to noise ratio (SNR). The pressure broadening coefficients of four acetylene transition lines are obtained using this fiber ring laser and an external cavity laser diode.

2007-01-01

313

Towards atomic scale engineering of rare-earth-doped SiAlON ceramics through aberration-corrected scanning transmission electron microscopy  

British Library Electronic Table of Contents (United Kingdom)

Direct visualization of rare earths in @a- and @b-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of @b-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in @a-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in @b-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.

2011-01-01

314

Thermoluminescence of irradiated RbCl and RbCl:Sn crystals  

International Nuclear Information System (INIS)

The thermoluminescence (TL) and emission of coloured RbCl and RbCl:Sn crystals are studied in the temperature range 300 to 560 K. The glow peaks responsible for F centres and tin centres in different valence states are identified using optical bleaching studies. The glow peaks are analysed using total curve fitting method and the kinetic parameters are determined. In moderately #gamma#-irradiated tin-doped RbCl crystals, the TL emission bands observed at 4.0, 3.6, and 2.2 eV are attributed to Sn"0, Sn"+, and Sn"- centers, respectively. A comprehensive energy level diagram depicting the various TL processes in these undoped and tin-doped RbCl crystals is proposed. (author).

315

Thermo-transferred thermoluminescence (TTTl) in potassium-yttrium double fluoride doped with terbium  

International Nuclear Information System (INIS)

This paper presents results of studying the thermo-transferred thermoluminescence (TTTl) phenomenon in potassium-yttrium double fluoride doped with terbium (K_2YF_5_:Tb) at different impurity concentrations (0.8%, 0.95% and 0.99%). Previously to study the TTTl phenomenon, structural characterization and chemical composition of the materials were determined. The structural studies were conducted using a scanning electron microscope; meanwhile, chemical composition was analyzed using energy dispersive X-ray spectroscopy. Thermoluminescence kinetics was studied irradiating the samples with "1"3"7Cs gamma rays as well as with "9"0Sr/"9"0Y beta rays, analyzing the glow curves by the deconvolution method for obtaining the kinetic parameters. (Author)

2011-02-01

316

The influence of Cl[sub 2] on Si[sub 1-x]Ge[sub x] selective epitaxial growth and B-doping properties by UHV-CVD  

Energy Technology Data Exchange (ETDEWEB)

We report the influence of a small quantity of Cl[sub 2], which enhanced the selectivity of silicon-selective epitaxial growth (Si-SEG) in UHV-CVD using Si[sub 2]H[sub 6], on both the epitaxial growth rate and the B-doping properties for each Si and Si[sub 1-x]Ge[sub x] film. The small quantity of Cl[sub 2] inhibited the Si, Ge and B incorporation, while the selectivity was enhanced. However, it was found, in the case of Si[sub 1-x]Ge[sub x]-SEG using Cl[sub 2], that the reduction ratio of both the growth rate and the B incorporation were smaller than those of Si-SEG with the selectivity still more enhanced. (orig.)

1993-02-01

317

The Effect of Contacts on the Counting Characteristics of Heavily Doped Normal-Type Cadmium-Telluride  

Science.gov (United States)

Cadmium telluride single crystals were grown heavily doped with chloride by the THM method. The resulting crystals were n-type with free carrier concentrations of the order of 10('12)/cm at room temperature. Hall effect studies revealed room temperature mobilities between 30 and 350 cm('2)/v-sec and resistivites between 2 x 10('3) and 10('4) ohm-cm. Studies were made of the gamma and alpha counting characteristics of these crystals with metal, metal-semiconductor, and metal-insulator electrodes. It was found that the MIS and MSS structures resulted in significant improvement over the MS structures in counting, signal-to-noise and energy resolution.

1985-01-01

318

Superconductivity in cage doped fullerenes. Final report  

Energy Technology Data Exchange (ETDEWEB)

Motivated by the discovery of superconductivity in alkali and alkaline earth fullerides, this program was undertaken both to understand the nature of and expand the range of materials demonstrating superconductivity. The first approach involved attempts to modify the fullerene cage by incorporating heteroatoms in the structure and the preparation and photophysical properties of nitrogen and sulfur doped fullerenes were studied in detail. The second approach involved examining the stoichiometry and effect of preparative conditions on the behavior of alkali, alkaline earth, lanthanide and mixed ion fullerides. In particular, the authors have elaborated on a technique for making such salts using liquid ammonia or aliphatic amines as solvents. Thirdly, modeling studies were undertaken to predict the properties of heterohedral fullerines and metal - C60 complexes, and theoretical guidelines were developed for understanding the reactivity of the fullerene cage to common ...

1996-08-26

319

Study of point defect detectors in Si  

International Nuclear Information System (INIS)

The importance of point defects in semiconductor and function materials has been studied in detail, but effective means for detecting point defects has not been available for a long time. The end of range defects in Si, produced by 140 keV Ge"+ implantation, were investigated as detectors for measuring the interstitial concentration created by 42 keV B"+ implantation. The concentration of interstitial resulting from the B"+ implantation and the behavior of the interstitial flux under different annealing condition were given. The enhanced diffusion in the boron doped EPI marker, resulting from mobile non-equilibrium interstitials was demonstrated to be transient. Interstitial fluxes arising from processing can be detected by transient enhanced diffusion (TED) of doped marker layers as well

1999-05-01

320

Study of phase composition and mechanical properties of Al-Mg alloys doped with Ce and Y after various conditions of heat treatment  

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

321

Spectroscopy of gadolinium gallium garnet crystals doped with Y b3+ revisited  

International Nuclear Information System (INIS)

The optical spectroscopy measurements of gadolinium gallium garnet (GGG) crystals doped with Yb show evidence of the presence of non-equivalent optical centers with very similar radiative decay rates. The energy level schemes of those centers have been determined on the basis of optical absorption, luminescence and Raman experiments. Crystal field fitting resulted in two sets of slightly different crystal field parameters for two non-equivalent Yb centers. Both sets of parameters describe perfectly the experimentally detected Y b3+ energy levels. Correlation between systematic trends in the experimental energy level schemes and crystal field parameters is discussed.

2010-06-30

322

Spectroscopic properties of Pr"3"+ doped LaWO_4Cl and La_3WO_6Cl_3  

International Nuclear Information System (INIS)

The spectroscopic properties of Pr"3"+ doping two lanthanum chlorotungstate hosts: the orthorhombic LaWO4Cl (1-1) and the hexagonal La3WO4Cl6 (3-1), as well as those of PrWO4Cl and Pr3wO613 have been investigated. The simulations of the energy level schemes are carried out within the crystal field theory frame. Each simulation involves 7 free ion parameters and 14 non-zero crystal field parameters (cfps), corresponding to the C_s point symmetry of the site occupied by the rare earth, in both structures.

1992-01-01

323

Spectroscopic properties of Pr sup 3+ doped LaWO sub 4 Cl and La sub 3 WO sub 6 Cl sub 3  

Energy Technology Data Exchange (ETDEWEB)

The spectroscopic properties of Pr{sup 3+} doping two lanthanum chlorotungstate hosts: the orthorhombic LaWO4Cl (1-1) and the hexagonal La3WO4Cl6 (3-1), as well as those of PrWO4Cl and Pr3wO613 have been investigated. The simulations of the energy level schemes are carried out within the crystal field theory frame. Each simulation involves 7 free ion parameters and 14 non-zero crystal field parameters (cfps), corresponding to the C{sub s} point symmetry of the site occupied by the rare earth, in both structures.

1992-01-01

324

SI/SIGE NANOWIRE ARRAYS FOR THERMOELECTRICITY  

Environmental Research Database

ObjectivesFor thermoelectricity both low thermal conductivity and high electrical conductivity are required. High electrical conductivity should be established via a high carriers concentration and a high mobility.~%~The aim of this feasibility study is to investigate a method of modulation doping of Si nanowires in order to generate high carrier concentrations without the need for impurity doping, thus retaining high mobilities.~%~~%~The objectives are (in chronological order):~%~- reduction of the wire [continued...]DescriptionIn recent years, the increasing dependence of society on fossil fuels for socio-economical development has become a cause of great concern. The possibility of a reduced availability of fossil fuels, and the effect of these fuels on climate change, have encouraged research into alternative energy sources. Many of these alternatives are old ideas, implemented using modern techniques. This proposal plans ...

2008-01-30

325

Radiation tolerant GaAs MESFET with a highly-doped thin active layer grown by OMVPE  

International Nuclear Information System (INIS)

A new structure of GaAs MESFET with high radiation tolerance is proposed. Changes in electrical parameters of a GaAs MESFET as a function of total #gamma#-ray dose have been found to be caused mainly by a decrease in the effective carrier concentration in an active layer. The authors have designed a new structure from a simulation based on an empirical relationship between the changes of the effective carrier concentration and the total #gamma#-ray dose. It has been successfully demonstrated by utilizing a highly-doped thin active layer (4 x 10"1"8 cm"-"3, 100 Angstrom) grown by OMVPE. This MESFET can withstand a dose ten times higher [1 x 10"9 rads(GaAs)] than a conventional one can.

1990-07-16

326

Properties of transition metal-doped zinc chalcogenide crystals for tunable IR laser radiation  

Energy Technology Data Exchange (ETDEWEB)

The spectroscopic properties of Cr{sup 2+}, Co{sup 2+}, and Ni{sup 2+}-doped single crystals of ZnS, ZnSe, and ZnTe have been investigated to understand their potential application as mid-IR tunable solid-state laser media. The spectroscopy indicated divalent Cr was the most favorable candidate for efficient room temperature lasing, and accordingly, a laser-pumped laser demonstration of Cr:ZnS and Cr:ZnSe has been performed. The lasers` output were peaked at {approximately} 2.35 {mu}m and the highest measured slope efficiencies were {approximately} 20% in both cases.

1995-03-17

327

Progress on polarized target materials with pure carbon background  

Science.gov (United States)

A previous note reviewed methods for the paramagnetic doping of materials for spin-polarized solid targets and some of the history of attempts to apply those methods to hydrocarbons. Since the earlier work on hydrocarbons had yielded, at best, rather mediocre results, that note also speculated on some ways to extend and, possibly, to improve upon the earlier work. The sharpest focus was on the light (number of carbons less than six) alkanes, since these are the hydrocarbons that have the highest hydrogen contents ([approx gt] 17wt %) and therefore require the least degree of polarization to be interesting. This present note summarizes the subsequent work done, to date, exploring some of the issues related to the chemical doping method. The main areas of progress have been in the literature search, experimental results on glass formation by alkanes, and a polarizing test of a prototype'' hydrocarbon.

1993-03-24

328

Progress on polarized target materials with pure carbon background  

Energy Technology Data Exchange (ETDEWEB)

A previous note reviewed methods for the paramagnetic doping of materials for spin-polarized solid targets and some of the history of attempts to apply those methods to hydrocarbons. Since the earlier work on hydrocarbons had yielded, at best, rather mediocre results, that note also speculated on some ways to extend and, possibly, to improve upon the earlier work. The sharpest focus was on the light (number of carbons less than six) alkanes, since these are the hydrocarbons that have the highest hydrogen contents ([approx gt] 17wt %) and therefore require the least degree of polarization to be interesting. This present note summarizes the subsequent work done, to date, exploring some of the issues related to the chemical doping method. The main areas of progress have been in the literature search, experimental results on glass formation by alkanes, and a polarizing test of a prototype'' hydrocarbon.

1993-03-24

329

Progress on polarized target materials with pure carbon background  

Energy Technology Data Exchange (ETDEWEB)

A previous note reviewed methods for the paramagnetic doping of materials for spin-polarized solid targets and some of the history of attempts to apply those methods to hydrocarbons. Since the earlier work on hydrocarbons had yielded, at best, rather mediocre results, that note also speculated on some ways to extend and, possibly, to improve upon the earlier work. The sharpest focus was on the light (number of carbons less than six) alkanes, since these are the hydrocarbons that have the highest hydrogen contents ({approx_gt} 17wt %) and therefore require the least degree of polarization to be interesting. This present note summarizes the subsequent work done, to date, exploring some of the issues related to the chemical doping method. The main areas of progress have been in the literature search, experimental results on glass formation by alkanes, and a polarizing test of a ``prototype`` hydrocarbon.

1993-03-24

330

Preparation and photocatalytic property of pyrochlore Bi2Ti2O7 and (Bi, La) 2Ti2O7 films  

British Library Electronic Table of Contents (United Kingdom)

Dopant-free Bi2Ti2O7 thin films with pyrochlore structure and La-doped bismuth titanate thin films have been fabricated by means of chemical solution decomposition, and characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy and UV?Vis spectrophotometry in this study. Their photocatalytic activities have been evaluated by photodegrading methyl orange solution, and the optimum processing parameters for the highest photocatalytic activity have been found. Moreover, the effects of La-doping on the phase transformation and the photocalalytic activity have been studied. It has been deduced from the experiment result that substituted La3+ ions can act as a stabilizer of Aurivillus phase BLT and a grain?growth inhibitor in BLT thin films.

2008-01-01

331

Performance improvement of quantum dot infrared photodetectors through modeling  

British Library Electronic Table of Contents (United Kingdom)

This paper presents a method to evaluate and improve the performance of quantum dot infrared photodetectors (QDIPs). We proposed a device model for QDIPs. The developed model accounts for the self-consistent potential distribution, features of the electron capture and transport in realistic QDIPs in dark and illumination conditions. This model taking the effect of donor charges on the spatial distribution of the electric potential in the QDIP active region. The model is used for the calculation of the dark current, photocurrent and detectivity as a function of the structural parameters such as applied voltage, doping QD density, QD layers, and temperature. It explains strong sensitivity of dark current to the density of QDs and the doping level of the active region. In order to confirm our...

2010-01-01

332

Optical properties and up-conversion of Pr"3"+ doped CdS nanoparticles in sol-gel glasses  

International Nuclear Information System (INIS)

Silica glasses containing Pr"3"+ with and without CdS nanoparticles were prepared by sol-gel technique. The influence of CdS nanoparticles on Pr"3"+ doped glass was studied by absorption, photoluminescence and up-conversion. From the measured intensities of various absorption bands of these glasses, the Judd-Ofelt parameters ?_2, ?_4 and ?_6 have been evaluated. The radiative transition probability (A), radiative lifetime (?_R), branching ratio (?_R) and integrated emission cross-section (?_P) were calculated from excited states of "3P_1 and "3P_0 levels. The up-conversion emissions were found in the green, orange and red regions under 800 nm excitation with peaks 559, 612 and 688 nm respectively. On excitation with 370 nm also leads to similar green, orange and red regions.

2010-10-01

333

On character of organic additives effect on pitting corrosion rate of steel-Kh25T at various potentials  

International Nuclear Information System (INIS)

The dependence of the inhibiting action of some surface active organic substances (SAOS) on the pitting- formation potential epsilonsub(p) has been investigated for the steel Kh25T. The study has been performed by potentiostatic method using the H_2SO_4 0.1-n-solution doped by NaCl, Na_2SO_4, in the presence of SAOS of different classes. As epsilonsub(p) shifts in positive direction from +0.6 to +1.1 V, the inhibiting action of the SAOS series (o-oxyquinoline) increases gradually till some critical potential above which SAOS favour pitting destruction of steel. This phenomenon should be considered in anodic protection in SAOS-doped solutions.

334

Occurence of active layer optical properties on some Lasing characteristics dye-doped Ch LC  

CERN Document Server

Effect of a planar texture quality and its thickness on lasing spectrums and thresholds in dye-doped cholesteric liquid crystal (CLC) of steroid type is explored. Transition from the qualitative planar texture to the poor texture quality is accompanied by change of characteristic mode structures and by shift of barycentre in the long-wave side and the considerable growth of the lasing threshold. It is found that in the CLC texture created by substrates with perpendicular directions of orientation the stable single-mode lasing takes place. The nature of oscillated modes in such texture is caused by phase jump. The gained results show that in steroid CLC, unlike induced one, lasing spectrums is possible to feature with the coupled wave model. Key words: steroidal cholesteric liquid crystal, distributed feedback lasing, oscillation thresholds, phase defect of periodical structure, transmission and lasing spectra

2010-01-01

335

Mechanical Properties and Thermal Shock Resistance of Refractory Self-Reinforced -SiAlONs Using Barium Aluminosilicate as an Additive  

British Library Electronic Table of Contents (United Kingdom)

Yb-, Y-, Yb/Y-, and Yb/Nd-doped -SiAlON ceramics with 5-wt% barium aluminosilicate (BAS) were synthesized by hot pressing. Typical self-reinforced microstructures were obtained in all investigated -SiAlONs in spite of the type of doped cations. This is attributed to the incorporation of BAS, which could supply suitable liquid phase to promote the anisotropic growth of the -SiAlON grains. All the composites exhibited excellent high-temperature mechanical properties and thermal shock resistance due to the formation of a self-reinforced microstructure and the complete crystallization of BAS additive.

2011-01-01

336

Materials aspects of multijunction solar cells  

Energy Technology Data Exchange (ETDEWEB)

Atomic layer epitaxy (ALE) was used to grow several components of the cascade solar cell structure in the AlGaAs/GaAs system. An ALE reactor was constructed for multiwafer growth with a growth rate of 0.6 {mu}m h{sup -1}. Device quality GaAs and Al{sub x}Ga{sub 1-x}As films were grown with p-type background carbon doping in the ranges 10{sup 16}-10{sup 19} cm{sup -3} and 10{sup 16}-10{sup 20} cm{sup -3} respectively. N-type films were achieved by SiH{sub 4} doping, producing carrier concentrations in the range 10{sup 16}-10{sup 18} cm{sup -3}. In addition, the potential applications of the ALE technique in the photovoltaic field are discussed. (orig.).

1991-05-01

337

Layer-by-layer assembly of functional silica and Au nanoparticles for fabricating electrogenerated chemiluminescence sensor  

Energy Technology Data Exchange (ETDEWEB)

We described the use of silica nanoparticles as building blocks for the immobilization of electrogenerated chemiluminescence (ECL) reagent Ru(bpy){sub 3}{sup 2+} and the fabrication of layer-by-layer assembly film by alternating the deposition of the Ru(bpy){sub 3}{sup 2+}-doped silica nanoparticles and Au nanoparticles. UV-vis absorption spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry and ECL were used to characterize the uniform growth of the multilayer film. Since Ru(bpy){sub 3}{sup 2+} could still maintain its ECL property when doped into the silica nanoparticles, the as-prepared multilayer film could be used as an effective ECL sensor, and the sensor showed high sensitivity and good stability.

2008-09-20

338

Layer-by-layer assembly of functional silica and Au nanoparticles for fabricating electrogenerated chemiluminescence sensor  

International Nuclear Information System (INIS)

We described the use of silica nanoparticles as building blocks for the immobilization of electrogenerated chemiluminescence (ECL) reagent Ru(bpy)_3"2"+ and the fabrication of layer-by-layer assembly film by alternating the deposition of the Ru(bpy)_3"2"+-doped silica nanoparticles and Au nanoparticles. UV-vis absorption spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry and ECL were used to characterize the uniform growth of the multilayer film. Since Ru(bpy)_3"2"+ could still maintain its ECL property when doped into the silica nanoparticles, the as-prepared multilayer film could be used as an effective ECL sensor, and the sensor showed high sensitivity and good stability.

2008-09-20

339

Layer-by-layer assembly of functional silica and Au nanoparticles for fabricating electrogenerated chemiluminescence sensor  

British Library Electronic Table of Contents (United Kingdom)

We described the use of silica nanoparticles as building blocks for the immobilization of electrogenerated chemiluminescence (ECL) reagent Ru(bpy)32+ and the fabrication of layer-by-layer assembly film by alternating the deposition of the Ru(bpy)32+-doped silica nanoparticles and Au nanoparticles. UV-vis absorption spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry and ECL were used to characterize the uniform growth of the multilayer film. Since Ru(bpy)32+ could still maintain its ECL property when doped into the silica nanoparticles, the as-prepared multilayer film could be used as an effective ECL sensor, and the sensor showed high sensitivity and good stability.

2008-01-01

340

Investigation into #beta##reversible##omega#-transformation in pseudo -#beta# -titanium VT30 alloy, doped with hydrogen  

International Nuclear Information System (INIS)

To study #beta# #reversible# #omega#-transformation in pseudo-#beta#-titanium alloy VT30, doped by hydrogen, methods of X-ray diffraction and thermodifferential analyses are used. It is established that in the process of heating of the hardened alloy from 0.004-0.1% H first formation and then dissolution of #omega# phase take place. An increase in hydrogen content to 0.1% decreases thermal effect of the processes and does not affect the temperature of #beta# #reversible# #omega#-transformation. Introduction of hydrogen in the concentration of 0.2% and higher suppresses completely #beta# #reversible# #omega# - transformation. A decrease in heating rate displaces #beta# #reversible# #omega#-transformation to lower temperatures.

341

Internal friction of amorphous Pd/sub 80/ Si/sub 20/ metal doped with hydrogen isotopes  

Energy Technology Data Exchange (ETDEWEB)

Internal friction of amorphous Pd/sub 80/Si/sub 20/ metal doped with hydrogen or deuterium was measured with a specially designed apparatus using amorphous metal sheet as a part of the electric oscillating circuit. Two peaks in Q/sup -1/ curve are observed. Applying the peak shift method to the first Snoek-like peak, we can determine the relaxation time from which the microdiffusion coefficient can be calculated. The obtained microdiffusion coefficient is about 10/sup -14/ m/sup 2//s at 200 K, being comparable with the macrodiffusion coefficient obtained from the releasing method. It can, however, not elucidate the hydrogen isotopic effect on the peak temperature of Q/sup -1/ curve, the activation energy for relaxation and the relaxation time from the present work because of the broadness of obtained Q/sup -1/ curve.

1983-02-01

342

Injection control and thermally stimulated current in ionic polarized polymer based light emitting diode  

International Nuclear Information System (INIS)

An effective method of enhancing charge injection and electroluminescence efficiency of polymer-based light emitting diode is introduced. Spin-coated films of poly (N-vinylcarbazole) blended with electron-transport material (Bu-PBD), laser dye (Coumarin6), and the typical supporting electrolyte (tetraethylammonium perchlorate; TEAP) were examined and it was found that the injection current and luminance of the light emitting diode doped with TEAP were enhanced dramatically after heat-treatment at 80 deg. C and appropriate biasing in an external electric field of 1.5x10"8 V/m at this temperature. The thermally stimulated current (TSC) was also measured to investigate the relaxation process of ionic space charges in the films. The relaxation times of ionic polarization were found to be related to the cation size of the electrolyte. And the relaxation time becomes long enough by the use of TEAP doping.

2003-08-22

343

Influence of self-doped poly(aniline-co-4-amino-3-hydroxy-naphthalene-1-sulfonic acid) on corrosion inhibition behaviour of iron in acidic medium  

British Library Electronic Table of Contents (United Kingdom)

This paper presents the corrosion inhibition performance of soluble self-doped copolymers of aniline and 4-amino-3-hydroxy-naphthalene-1-sulfonic acid synthesized by chemical oxidative polymerization method. The corrosion inhibition behaviour of the copolymers in 1.0M HCl has been evaluated using Tafel Extrapolation method and electrochemical impedance spectroscopy (EIS) which was also used to propose the mechanism besides surface morphology. The results showed that the copolymer film exhibited the significant shifting in the corrosion potential and greater charge transfer resistance. The corrosion inhibition efficiency was found to increase from 50% to 90% by increasing the concentration of copolymer from 10 to 70mg/l in HCl medium. Moreover, the copolymer showed the larger degree of surf...

2011-01-01

344

I. Evaluation of thin Pd, Pt and Ni silicides Schottky barriers for silicon solar cells. II. Large-area uniform growth of Si layer by solid-phase epitaxy. Final report  

Energy Technology Data Exchange (ETDEWEB)

Stability and decomposition of PtSi, NiSi, and PdSi in contact with single crystal or amorphous Si is examined. PtSi, PdSi and NiSi are thermally stable both with Si, but are unstable in contact with metal film. It is shown that epitaxial Si layers can be obtained using both Pd and Al as metal film and layers can be electrically doped by the addition of a doping layer to the thin film structure prior to the heat treatment or by inclusion of Al atoms so that n/sup +/ and p/sup +/ conductivity can be achieved in the grown epilayer. The effects of impurities, substrate orientation on the growth kinetics are also discussed. (LEW)

1981-01-01

345

Flexible, all-organic ammonia sensor based on dodecylbenzene sulfonic acid-doped polyaniline films  

International Nuclear Information System (INIS)

A stable chlorobenzene dispersion of conducting polyaniline (PANI) has been obtained by doping emeraldine base with dodecylbenzene sulfonic acid (DBSA) and studied by spectrophotometric measurements in the UV-vis-IR range. The electrical properties of PANI: DBSA films obtained from the above dispersion have been investigated under different temperature and relative humidity conditions. All-organic chemoresistive devices have been developed by spin-coating the PANI: DBSA dispersion on flexible substrates, and then by depositing electrodes on the top, from a carbon nanotube conducting ink. Sensing tests performed under exposition to calibrated amounts of ammonia reveal that these simple and inexpensive sensors are able to detect ammonia at room temperature in a reliable way, with a sensitivity linearly related to concentration in the range between 5 ppm and 70 ppm.

2010-09-30

346

Enhancement in transition temperature and upper critical field of CeO0.8F0.2FeAs by yttrium doping  

Science.gov (United States)

We report significant enhancement in superconducting properties of yttrium substituted Ce1-xYxOFFeAs superconductors. The polycrystalline samples were prepared by two step solid state reaction technique. X-ray diffraction confirmed tetragonal ZrCuSiAs structure with decrease in both a and c lattice parameters on increasing yttrium substitution (with fixed F content). With smaller ion Y in place of Ce, the transition temperature increased by 6 K. Yttrium doping also lead to higher critical fields as well as broader magnetization loops, particularly at elevated temperature.

2009-12-01

347

Electrogenerated chemiluminescence sensor for itopride with Ru(bpy)32+-doped silica nanoparticles/chitosan composite films modified electrode  

British Library Electronic Table of Contents (United Kingdom)

A electrogenerated chemiluminescence (ECL) sensor for itopride was developed based on tris(2,2-bipyridyl)ruthenium(II) (Ru(bpy)32+)-doped silica (RuDS) nanoparticles/biopolymer chitosan composites membrane modified glassy carbon electrode (GCE). The RuDS nanoparticles (52+-5nm) were prepared by a modified Stber synthesis method and were characterized by electrochemical, fluorometric and transmission electron microscopy technology. The Ru(bpy)32+ encapsulation interior of the silica nanoparticle maintains its electrochemical activities and also reduces Ru(bpy)32+ leaching from the silica matrix when immersed in water due to the electrostatic interaction. The ECL analytical performances of this ECL sensor for itopride based on its enhancement ECL emission of Ru(bpy)32+ were investigated in d...

2008-01-01

348

Electrical properties of antimony doped PLZT ceramics prepared by mixed-oxide route  

International Nuclear Information System (INIS)

Ferroelectric [Pb_0_._9_2(La_1_-_zSb _z)_0_._0_8][Zr_0_._6_0Ti_0_._4_0]O_3 for z = 0.0, 0.3, 0.6, 0.9 and 1 were prepared from their constituent oxides by a solid state reaction technique. The powders were calcined in the temperature range of 1000 deg. C for 6 h. Phase formation, crystal structure and lattice parameter were investigated by X-ray diffraction (XRD) technique. The compacts were sintered at 1250 deg. C for 2 h and their dielectric, ferroelectric and conductive properties were measured. The ferroelectric behavior of the doped samples was studied from their hysteresis loop.

2006-12-21

349

Collection of athermal phonons into doped Ge thermistors using quasiparticle trapping  

Energy Technology Data Exchange (ETDEWEB)

We have developed a low-temperature particle detector that uses a novel quasiparticle trapping mechanism to funnel athermal phonon energy from an 80 mg Ge absorber into a 1.6 mg doped Ge thermistor via a superconducting Al film. We report on pulse height spectra obtained at 320 mK by scanning a {sup 241}Am alpha source along the device, and show that up to 20% of the energy deposited in the Ge absorber by a 5.5 MeV alpha particle interaction can be collected into a thermistor via quasiparticle trapping. We show that this device is sensitive to the position of an alpha particle interaction in the Ge absorber for interaction distances of up to 5 mm from a quasiparticle trap.

1995-05-15

350

Application of neutron transmutation doping method to initially p-type silicon material  

British Library Electronic Table of Contents (United Kingdom)

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x1019ncm-1. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual 32P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neut...

2009-01-01

351

/sup 109/Ag NMR spectra of aqueous silver ions coordinated with nitroxide radical. Silver-TANOL complex and TANOL as a doping agent  

Energy Technology Data Exchange (ETDEWEB)

The effects of TANOL radical have been examined on chemical shifts and relaxation rates of /sup 109/Ag NMR in aqueous solution of silver salts. The silver ion in aqueous solution is found to coordinate with TANOL radical. A small amount of TANOL is added as a doping agent(0.020M), since /sup 109/Ag signals are obtained for (1.0M) silver ion within 30 minutes. The /sup 109/Ag chemical shifts of silver salt in aqueous solutions were found within the range of 0 to -1000 ppm relative to that of 1.0M AgNo/sub 3/.

1982-09-01

352

Use of Eu"3"+ as an oxygen environment probe in alkali-alkaline earth-lanthanide phosphates with the #beta#-K_2SO_4 structure  

International Nuclear Information System (INIS)

The use of europium as a local structural probe allows the various phases appearing in the NaCaPO_4-Na_3Eu(PO_4)_2 and NaSrPO_4-Na_3Eu(PO_4)_2 systems to be detected. The broadening of the europium emission lines in going from the calcium to the strontium phases illustrates the ease of displacement of the PO_4 groups. (Auth.).

1983-09-01

353

The separation and determination of trace elements in iron ore  

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

2008-05-01

354

The relation between net calcium, alkali cation and chloride movements in red cells exposed to salicylate.  

UK PubMed Central (United Kingdom)

1. From a 150 mM-NH4 salicylate medium salicylate enters human red cells with a rate constant of 1.9 min-1 at 0 degrees C. 2. Salicylate increases the red cell permeability for Ca2+ (and Mg2+). There...Full Text Available

1979-02-01

355

Simultaneous lowering of serum phosphate and LDL-cholesterol by sevelamer hydrochloride (RenaGel) in dialysis patients.  

Science.gov (United States)

The aim of the current investigation was to study the effects of sevelamer hydrochloride (RenaGel) on serum phosphate, intact parathyroid hormone levels (iPTH), and lipid profiles in stable hemodialysis patients. Hemodialysis patients maintained on calcium containing phosphate binders were enrolled in this study. Following two weeks of washout of the phosphate binders, serum phosphate rose from 6.4 +/- 0.6 to 10.5 +/- 0.7 mg/dl (p <0.001). After 8 weeks of titration with sevelamer hydrochloride, serum phosphate fell by 4.5 +/- 0.3 to 6.3 +/- 0.7 mg/dl (p <0.0001). Serum calcium levels fell during washout (9.8 +/- 0.4 to 8.9 +/- 0.3 mg/dl, p <0.004) and were unaffected by sevelamer hydrochloride. Sevelamer hydrochloride administration was associated with a 23.0 +/- 3.1% fall in total cholesterol, a 35.9 +/- 3.0% fall in LDL cholesterol, and a 35.2 +/- 5.3% fall in the LDL:HDL cholesterol ratio (p <0.001). There was no change in HDL ...

1998-12-01

356

Roles of mitochondria and temperature in the control of intracellular calcium in adult rat sensory neurons  

UK PubMed Central (United Kingdom)

SUMMARYWe recorded Ca2+ current and intracellular Ca2+ ([Ca2+]i) in isolated adult rat dorsal root ganglion (DRG) neurons at 20 and...Full Text Available

2008-04-01

357

Research on the liquefaction of lignite by hydrogenation  

Energy Technology Data Exchange (ETDEWEB)

The investigations of lignite hydroliquefaction were aimed at improving reaction control in order to minimize residue and gas portion and hence increase the oil yield. To reach this goal, the process parameters were optimized and various catalysts tested for use in sump phase hydrogenation. Detailed investigations were also carried out on the problem of calcium carbonate agglomeration and the maceral decomposition behaviour of different lignite samples under hydrogenation conditions.

1985-01-01

358

Radioactive lead studies in the human  

International Nuclear Information System (INIS)

The differing susceptibility of individuals to the toxic effects of chronic lead exposure has never been fully understood. As the major intake of lead in the human is from food and beverages, any variation between individuals of the quantity of lead absorbed from the gut, and of the distribution and excretion of this lead, may account for the differences in individual susceptibility. The food and beverages themselves may have an influence, and to investigate their effects on absorption, distribution and excretion of lead, experiments were performed on normal subjects using a short lived radionuclide of lead, "2"0"3Pb, and instruments generally available in Nuclear Medicine. Lead absorption between different individuals showed a wide variation when "2"0"3Pb was taken as a single dose between meals. Minerals were found to be mainly responsible for affecting absorption when one subject ingested "2"0"3Pb in control meals from which one dietary constituent at a time was omitted. ...

359

Photolysis of the novel inotropes EMD 57033 and EMD 57439: evidence that Ca2+ sensitization and phosphodiesterase inhibition depend upon the same enantiomeric site.  

UK PubMed Central (United Kingdom)

1. We studied the effects of flash photolysis on the novel enantiomeric cardiac inotropes EMD 57033 (a calcium sensitizer) and EMD 57439 (a phosphodiesterase III inhibitor) in rat isolated ventricular...Full Text Available

1996-08-01

360

Perlinhibin, a Cysteine-, Histidine-, and Arginine-Rich Miniprotein from Abalone (Haliotis laevigata) Nacre, Inhibits In Vitro Calcium Carbonate Crystallization  

UK PubMed Central (United Kingdom)

We have isolated a 4.785 Da protein from the nacreous layer of the sea snail Haliotis laevigata (greenlip abalone) shell after demineralization with acetic acid. The sequence of 41...Full Text Available

2007-08-15

361

Pathophysiology of incomplete renal tubular acidosis in recurrent renal stone formers: evidence of disturbed calcium, bone and citrate metabolism  

DEFF Research Database (Denmark)

Urinary acidification, bone metabolism and urinary excretion of calcium and citrate were evaluated in 10 recurrent stone formers with incomplete renal tubular acidosis (iRTA), 10 recurrent stone formers with normal urinary acidification (NUA) and 10 normal controls (NC). Patients with iRTA had lower plasma standard bicarbonate after fasting (P <0.01) and lower urinary excretion of titratable acid (P <0.05) and citrate (P <0.01) compared with NUA patients and NC, and higher urinary excretion of ammonia (P <0.05) compared with NC (P <0.05). Hypercalciuria was found in 6 of 10 patients with iRTA compared with 3 of 10 with NUA, and 0 of 10 NC. The citrate/calcium ratio in urine was significantly reduced in iRTA compared with the value in NUA (P <0.01), and in NUA compared with NC (P <0.05). Biochemical markers of bone formation (serum osteocalcin) and bone resorption (urinary hydroxyproline) were significantly increased in iRTA ...

1993-01-01

362

Magnesium Sensitizes Slow Vacuolar Channels to Physiological Cytosolic Calcium and Inhibits Fast Vacuolar Channels in Fava Bean Guard Cell Vacuoles1  

UK PubMed Central (United Kingdom)

Vacuolar ion channels in guard cells play important roles during stomatal movement and are regulated by many factors including Ca2+, calmodulin, protein kinases, and phosphatases....Full Text Available

1999-11-01

363

Involvement of protein kinase C in the mechanism of action of Escherichia coli heat-stable enterotoxin (STa) in a human colonic carcinoma cell line, COLO-205  

International Nuclear Information System (INIS)

The present study was undertaken to determine the involvement of calcium-protein kinase C pathway in the mechanism of action of Escherichia coli heat stable enterotoxin (STa) apart from STa-induced activation of guanylate cyclase in human colonic carcinoma cell line COLO-205, which was used as a model cultured cell line to study the mechanism of action of E. coli STa. In response to E. coli STa, protein kinase C (PKC) activity was increased in a time-dependent manner with its physical translocation from cytosol to membrane. Inhibition of the PKC activity in membrane fraction and inhibition of its physical translocation in response to IP_3-mediated calcium release inhibitor dantrolene suggested the involvement of intracellular store depletion in the regulation of PKC activity. Among different PKC isoforms, predominant involvement of calcium-dependent protein kinase C (PKC#alpha#) was specified using isotype-specific ...

2005-08-01

364

Inactivating calcium-sensing receptor mutations in patients with primary hyperparathyroidism.  

Science.gov (United States)

Objective:? Primary hyperparathyroidism (HPT) is characterised by autonomous secretion of PTH from enlarged parathyroid glands leading, in most patients, to asymptomatic hypercalcaemia. Familial hypocalciuric hypercalcaemia (FHH) is an autosomal dominant disorder caused by inactivating mutations in the calcium sensing receptor (CaSR) gene; it is characterised by lifelong and usually asymptomatic hypercalcaemia. Establishing the correct diagnosis is important because surgery can be curative in HPT, but ineffective in FHH. There is overlap in the diagnostic criteria for the two disorders and some patients carrying inactivating mutations in the CaSR gene, which is suggestive of FHH, also have HPT with hyperplastic parathyroid glands or adenomas. Design and Patients:? CaSR gene mutations were analyzed and clinical and biochemical parameters evaluated in 139 consecutive out-patients presenting with hypercalcaemia and suspected of having HPT. Results:? Six different ...

2011-03-29

365

Gastrointestinal absorption of lead in chicks: involvement of the cholecalciferol endocrine system  

Energy Technology Data Exchange (ETDEWEB)

The role of dietary calcium and phosphorus in modifying the intestinal absorption of lead and also the effect of lead ingestion on the metabolism of cholecalciferol were studied in chicks. The efficiency of absorption of /sup 203/Pb and /sup 47/Ca was increased when the animals were fed a low calcium diet and treated with cholecalciferol. The synthesis of the vitamin D-induced calcium-binding protein (CaBP) was correspondingly increased. When the chicks were depleted of vitamin D and repleted with 1,25-dihydroxycholecalciferol (1,25(OH)/sub 2/D/sub 3/) as their only source of the vitamin, the absorption of both /sup 47/Ca and /sup 203/Pb was unaffected by dietary calcium levels, and no change in CaBP levels occurred. Low dietary intake of phosphorus resulted in an increase in /sup 47/Ca and /sup 203/Pb absorption and in CaBP synthesis when the animals were treated with cholecalciferol. However, when the ...

1984-04-01

366

Gastrointestinal absorption of lead in chicks: involvement of the cholecalciferol endocrine system  

International Nuclear Information System (INIS)

The role of dietary calcium and phosphorus in modifying the intestinal absorption of lead and also the effect of lead ingestion on the metabolism of cholecalciferol were studied in chicks. The efficiency of absorption of "2"0"3Pb and "4"7Ca was increased when the animals were fed a low calcium diet and treated with cholecalciferol. The synthesis of the vitamin D-induced calcium-binding protein (CaBP) was correspondingly increased. When the chicks were depleted of vitamin D and repleted with 1,25-dihydroxycholecalciferol [1,25(OH)_2D_3] as their only source of the vitamin, the absorption of both "4"7Ca and "2"0"3Pb was unaffected by dietary calcium levels, and no change in CaBP levels occurred. Low dietary intake of phosphorus resulted in an increase in "4"7Ca and "2"0"3Pb absorption and in CaBP synthesis when the animals were treated with cholecalciferol. However, when the birds were repleted with ...

367

Gamma interferon induces rapid and coordinate activation of mitogen-activated protein kinase (extracellular signal-regulated kinase) and calcium-independent protein kinase C in human monocytes.  

UK PubMed Central (United Kingdom)

Gamma interferon plays an important role in regulating the functional properties of mononuclear phagocytes. In the present study, the role of activated protein kinases in the mechanism of action of...Full Text Available

1994-07-01

368

Effect of secondary fuels and combustor temperature on mercury speciation in pulverized fuel co-combustion: part 1  

Energy Technology Data Exchange (ETDEWEB)

The present work mainly involves bench scale studies to investigate partitioning of mercury in pulverized fuel co-combustion at 1000 and 1300{sup o}C. High volatile bituminous coal is used as a reference case and chicken manure, olive residue, and B quality (demolition) wood are used as secondary fuels with 10 and 20% thermal shares. The combustion experiments are carried out in an entrained flow reactor with a fuel input of 7-8 kWth. Elemental and total gaseous mercury concentrations in the flue gas of the reactor are measured on-line, and ash is analyzed for particulate mercury along with other elemental and surface properties. Animal waste like chicken manure behaves very differently from plant waste. The higher chlorine contents of chicken manure cause higher ionic mercury concentrations whereas even with high unburnt carbon, particulate mercury reduces with increase in the chicken manure share. This might be a problem due to coarse fuel particles, low surface area, and iron ...

2007-08-15

369

Differential Roles for STIM1 and STIM2 in Store-Operated Calcium Entry in Rat Neurons  

UK PubMed Central (United Kingdom)

The interaction between Ca2+ sensors STIM1 and STIM2 and Ca2+ channel-forming protein ORAI1 is a crucial element of ...Full Text Available

370

Dietary calcium and magnesium intakes and the risk of type 2 diabetes: the Shanghai Women's Health Study123  

UK PubMed Central (United Kingdom)

Background: Diet plays a key role in the development of type 2 diabetes (T2D), but little is known about the contributions of specific nutrients in populations in which dietary patterns...Full Text Available

2009-04-01

371

Autocrine regulation of T-cell activation by ATP release and P2X7 receptors  

UK PubMed Central (United Kingdom)

T-cell activation requires the influx of extracellular calcium, although mechanistic details regarding such activation are not fully defined. Here, we show that P2X7 receptors play a key...Full Text Available

2009-06-01

372

A progress for the health of south countries. The solar refrigerator; Un progres pour la sante dans les pays du Sud. Le refrigerateur solaire  

Energy Technology Data Exchange (ETDEWEB)

In order to conserve vaccines in hot countries a solar refrigerator has been made by a French university. It is a photothermal refrigerator without batteries. It uses two gases: ammonia and calcium chloride. The refrigerator is autonomous and can work eleven days without sun. (N.C.)

1998-05-01

373

A comparison of nutrient dynamics in forest ecosystems along with the Warmth Index Gradient  

Energy Technology Data Exchange (ETDEWEB)

Nutrient elements contained in litter fall flux, that of uptake flux and turnover rate had generally tended to increase with the increase in the Warmth Index, while the amount of nutrient in the A[sub 0] horizon and nutrient use efficiency did not. However, it is suggested that topographic and climatic aridity, and the amount of available and exchangeable phosphorus, calcium and magnesium greatly affect the nutrient dynamics in a each forest ecosystem as the Warmth Index increases. (J.P.N.).

1993-01-01

374

A Laser-Pointer-Based Spectrometer for Endpoint Detection of EDTA Titrations  

Science.gov (United States)

A laser spectrometer for the ethylenediaminetetra-acetic acid (EDTA) titration of magnesium or calcium ions that is designed around a handheld laser pointer as the source and a photoresistor as the detector is developed. Findings show that the use of the spectrometer reduces the degree of uncertainty and error in one part of the EDTA titrations, however overall standard deviations depend on the skill of the student and their willingness to be careful and precise.

2004-12-01

375

Agonist-directed trafficking of signalling at serotonin 5-HT2A, 5-HT2B and 5-HT2C-VSV receptors mediated Gq/11 activation and calcium mobilisation in CHO cells.  

Science.gov (United States)

Several examples of agonist-directed trafficking of receptor signalling at 5-HT2A and 5-HT2C receptors have been reported that involve independent downstream transduction pathways. We now report the functional selectivity of a series of chemically diverse agonists at human (h)5-HT2A, h5-HT2B and h5-HT2C-VSV by examining two related responses, the upstream activation of Gq/11 proteins in comparison with its associated cascade of calcium mobilisation. At the h5-HT2A receptor, d-lysergic acid diethylamide (LSD) and the antiparkinsonian agents lisuride, bromocriptine and pergolide exhibit a higher potency for Gq/11 activation than calcium release in contrast with all the other tested ligands such as 5-HT, mCPP and BW723C86, that show an opposite preference of signalling pathway. Comparable observations are made at h5-HT2B and h5-HT2C-VSV receptors, suggesting a similar mechanism of functional selectivity for the three serotonin receptors. ...

2008-07-30

376

The rare earth antimonates: spectroscopic properties, crystal field and paramagnetic susceptibility simulations  

International Nuclear Information System (INIS)

The rare earth antimonates RE_3Sb_5O_1_2 constitute an isostructural series, where the rare earth site symmetry is S_4. The spectroscopic properties of pure or doped compounds of this family are studied in order to derive their energy level schemes and to simulate them through the crystal field theory, by using the approximated D_2_d potential. The paramagnetic susceptibilities are calculated with the derived wavefunctions and compared to experiment.

1990-09-01

377

The effects of helium on the embrittlement and hardening of boron doped EUROFER97 steels  

International Nuclear Information System (INIS)

The role of helium in a process of embrittlement and hardening of RAFM steels was investigated in EUROFER97 based experimental heats, ADS2, ADS3 and ADS4, that were doped with different contents of natural B and the separated 10B-isotope (0.008-0.112 wt.%). The neutron irradiation of the boron doped and the reference RAFM steels was performed in the Petten High Flux Reactor up to 16.3 dpa at different temperatures between 250 and 450 deg. C. The embrittlement behaviour and hardening was investigated by instrumented Charpy-V tests with subsize specimens. Irradiation lead to generation of 84, 432 and 5580 appm He in ADS2, ADS3 and ADS4 steels, respectively. At irradiation temperatures Tirr ? 350 deg. C the boron doped steals show progressive embrittlement and reduction of toughness with increasing helium amount. The analysis of the hardening vs. embrittlement behaviour at Tirr ? 350 deg. C reveals hardening nature of ...

2008-12-01

378

Suppression of afterglow in CsI:Tl by co doping with Eu"2"+-II: Theoretical model  

International Nuclear Information System (INIS)

The mechanism for afterglow suppression in codoped CsI:Tl,Eu reported in the preceding paper was investigated by combined radioluminescence and thermoluminescence experiments. Model rate equations informed by these experiments were employed to simulate afterglow. It was found that codoping with europium introduces deep electron traps, with room-temperature glow peaks, that effectively scavenge the electrons from shallow traps associated with thallium, thus suppressing afterglow in the time domain of tens of milliseconds.

2006-03-15

379

Spin fluctuation changes in Ge doped YbPd_2Si_2  

International Nuclear Information System (INIS)

In YbPd_2Si_2, the valence of Yb is very close to 3+. Ge substitution of Si induces a negative pressure effect and the valence of Yb decreases. For the low Ge concentrations studied, the spin fluctuation temperature T_s_f increases and #chi#4f, the Yb derived 4f susceptibility, obeys the scaling law #chi#4f(T)=F(T/T_s_f). (orig.).

380

Spectral analysis of Pr3+-, Sm3+- and Dy3+-doped transparent GeO2-BaO-TiO2 glass ceramics  

British Library Electronic Table of Contents (United Kingdom)

In this paper, we present the photoluminescence properties of Pr3+-, Sm3+- and Dy3+-doped germanate glasses and glass ceramics. From the X-ray diffraction measurement, the host glass structure was determined. These glasses have shown strong absorption bands in the near-infrared (NIR) region. Compared to Pr3+-, Sm3+- and Dy3+-doped glasses, their respective glass ceramics have shown stronger emissions due to the Ba2TiGe2O8 crystalline phase. For Pr3+-doped glass and glass ceramic, emission bands centered at 530nm (3P03H5), 614nm (3P03H6), 647nm (3P03F2) and 686nm (3P03F3) have been observed with 485nm (3H43P0) excitation wavelength. Of them, 647nm (3P03F2) has shown bright red emission. Emission bands of 4G5/26H5/2 (565nm), 4G5/26H7/2 (602nm) and 4G5/26H9/2 (648nm) for the Sm3+:glass and gl...

2009-01-01

381

Simulation of arsenic diffusion during rapid thermal annealing of silicon layers doped with low-energy high-dose ion implantation  

International Nuclear Information System (INIS)

The model of transient enhanced diffusion of ion-implanted As is formulated and the finite-difference method for numerical solution of the system of equations obtained is developed. The nonuniform distribution of point defects near the interface and more accurate description of arsenic clustering are simultaneously taken into account. Simulation of As diffusion during rapid annealing gives a reasonable agreement with the experimental data. (authors)

2005-09-01

382

Simulation aided hardening of N-channel power MOSFETs to prevent single event burnout  

International Nuclear Information System (INIS)

2D MEDICI simulator is used to investigate hardening solutions to single-event burnout (SEB). SEB parametric dependencies such as carrier lifetime reduction, base enlargement, and emitter doping decrease have been verified and a p"+ plug modification approach for SEB hardening of power MOSFETs is validated with simulations on actual device structures.

1995-07-17

383

STM studies of CDWs in pure and doped transition metal chalcogenides  

Energy Technology Data Exchange (ETDEWEB)

The effects of dilute impurity doping on charge-density wave (CDW) structures and gaps in NbSe{sub 3} 1T-TaS{sub 2} and 2H-NbSe{sub 2} have been studied by using a scanning tunneling microscope (STM) operating at 4.2 K. In Fe doped samples of NbSe{sub 3} the STM spectroscopy measurements indicate that the added impurities can significantly shift the CDW energy gaps. In NbSe{sub 3}, Fe reduces both CDW gaps by 25-30%, and produces changes in the conductance structure relative to the pure material. The images of Fe{sub 0.01}NbSe{sub 3} show that all three surface chains in the unit cell still carry a strong CDW modulation with no evident disorder. However, a change in the relative amplitudes of the high and low temperature CDWs is detected. The effects of Co and Ni impurities on the gaps in NbSe{sub 3} have also been studied. While Co increases both by 25-30%, Ni increases only the high temperature gap with the low temperature gap remaining ...

1992-12-01

384

Residual #alpha#-Si_3N_4 in O' crystals in CeO_2-doped O' + #beta#' SiAlON ceramics  

International Nuclear Information System (INIS)

The microstructure of a pressureless sintered (1,605 C, 90 min) O' + #beta#' SiAlON ceramic with CeO_2 doping has been investigated. It is duplex in nature, consisting of very large, slablike elongated O' grains (20--30 #mu#m long), and a continuous matrix of small rodlike #beta#' grains (< 1.0 #mu#m in length). Many #alpha#-Si_3N_4 inclusions (0.1--0.5 #mu#m in size) were found in the large O' grains. CeO_2-doping and its high doping level as well as the high Al_2O_3 concentration were thought to be the main reasons for accelerating the reaction between the #alpha#-Si_3N_4 and the Si-Al-O-N liquid to precipitate O'-SiAlON. This caused the supergrowth of O' grains. The rapid growth of O' crystals isolated the remnant #alpha#-Si_3N_4 from the reacting liquid, resulting in a delay in the #alpha# #-># #beta#-Si_3N_4 transformation. The large O' grains and the #alpha#-Si_3N_4 inclusions have a pronounced effect on the ...

385

Radiation hardening of optical fiber links by photobleaching with light of shorter wavelength  

International Nuclear Information System (INIS)

The influence of additionally injected short-wavelength photobleaching light on the radiation hardness of Ge-doped graded index fibers working at 1,300 nm wavelength is investigated. Predictions are complicated by the fact that more efficient shortwave bleaching light experiences higher radiation-induced loss. Promising results are found for low fiber temperatures (approx-lt -50 C) and bleaching light of about 835 nm wavelength.

1995-09-18

386

Photooxidation of different organic dyes (RB, MO, TB, and BG) using Fe(III)-doped TiO{sub 2} nanophotocatalyst prepared by novel chemical method  

Energy Technology Data Exchange (ETDEWEB)

The nano-structured Fe(III)-doped TiO{sub 2} photocatalysts with anatase phase have been developed for the oxidation of non-biodegradable different organic dyes like methyl orange (MO), rhodamine B (RB), thymol blue (TB) and bromocresol green (BG) using UV-Hg-lamp. The different compositions of Fe{sub x}Ti{sub 1-x}O{sub 2} (x = 0.005, 0.01, 0.05, and 0.1) nanocatalysts synthesized by chemical method (CM), have been characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra, specific surface area (BET), transmission electronic microscopy (TEM) analysis, XPS, ESR and zeta potential. From XRD analysis, the results indicate that all the compositions of Fe(III) doped in TiO{sub 2} catalysts gives only anatase phase not rutile phase. For complete degradation of all the solutions of the dyes (MO, RB, TB, and BG), the composition with x = 0.005 is more photoactive compared all other compositions of Fe{sub x}Ti{sub 1-x}O{sub 2}, and ...

2008-09-15

387

Peculiarities of #beta#-solid solution decomposition in (#alpha#+#beta#) titanium alloy at low temperature  

International Nuclear Information System (INIS)

The physical methods were used to study the decomposition of a metastable #beta#-solid solution in the VT22 two-phase titanium alloy. It is shown that the martensitic #beta# #-># #alpha#'' transformation in doped-element depleted microvolumes of the #beta#-solid solution are dominanted and the long-time multistage decomposition through a number of intermediate states in others.

388

Nonformity of the electron density in amorphous silicon films  

Energy Technology Data Exchange (ETDEWEB)

The authors study the nonuniformity of a-Si:H films obtained by the method of vacuum condensation, with the help of x-ray small-angle scattering (SLS) and transmission electron microscopy. Films of hydrogenated amorphous silicon are greatest interest, because the electronic properties of this material can be controlled by doping. As a result of the compensation of the ruptured bonds, and possibly, effects of melting, the properties of such films are analogous to those of singlecrystalline silicon. XLS enables a quantitative determination of the prameters of the regions of low electron density (RLD) in such objects.

1985-12-01

389

New crystals for dual-readout calorimetry  

CERN Document Server

Lead tungstate crystals doped with small fractions of praesodynium or molybdenum have been tested in beams of high-energy electrons. The goal of these tests was to study the effects of such dopants on the capability to separate the signal components deriving from the Cherenkov and scintillation light generated by the beam particles. These studies were carried out in view of the possible application of such crystals in dual-readout calorimeters.

2009-01-01

390

Intrinsic and extrinsic crossluminescence in ionic crystals  

Energy Technology Data Exchange (ETDEWEB)

Intrinsic crossluminescence (CRL) of CsBr, CsCl, and of BaF{sub 2} was investigated with electron-beam and synchrotron radiation excitation. From the CRL spectra, the excitation spectra and the reflectivity, energy level schemes were deduced. Extrinsic CRL was observed changing either the initial (CsCl:Br{sup -}) or the final (RbCl:Cs{sup +}; KCl:Cs{sup +}) state of CRL by doping. (author).

1991-01-01

391

Intrinsic and extrinsic crossluminescence in ionic crystals  

International Nuclear Information System (INIS)

Intrinsic crossluminescence (CRL) of CsBr, CsCl, and of BaF_2 was investigated with electron-beam and synchrotron radiation excitation. From the CRL spectra, the excitation spectra and the reflectivity, energy level schemes were deduced. Extrinsic CRL was observed changing either the initial (CsCl:Br"-) or the final (RbCl:Cs"+; KCl:Cs"+) state of CRL by doping. (author).

1990-09-03

392

Hydrogen effect or texture and deformation mechanism in #beta#-titanium alloy cold rolling  

International Nuclear Information System (INIS)

The relationships of hydrogen alloyed #beta#-titanium alloy deformation behaviour to its microstructure and texture are investigated. It is shown that plasticity increases and strain induced texture changes at low hydrogen contents (0.1-0.2 mass %). Possible mechanisms responsible for specific features of #beta#-Ti alloy deformation are discussed. The study is made using alloy VT35 doped with hydrogen

1999-09-01

393

High-temperature ferromagnetism in laser-deposited layers of silicon and germanium doped with manganese or iron impurities  

Energy Technology Data Exchange (ETDEWEB)

The paper reports on the results of a study of the synthesis conditions effects on magnetic and transport properties of nanosized layers of high-T{sub c} diluted magnetic semiconductors (DMS), such as Ge:Mn, Si:Mn and Si:Fe, fabricated by laser-plasma deposition over a wide range of the growth temperature, T{sub g}=(20-550) deg. C on single-crystal GaAs or Al{sub 2}O{sub 3} substrates. Ferromagnetism of the layers was detected by measurement data of the magneto-optical Kerr effect, anomalous Hall effect, negative magnetoresistance and ferromagnetic resonance (FMR) at 5-500 K. The optimum growth temperature, T{sub g}, for Si:Mn/GaAs layers with T{sub c}{approx}400 K is shown to be about 400 deg. C. The Si:Mn/Al{sub 2}O{sub 3} layers with 35% of Mn have the metal-type of conductivity with manifestation of magnetization up to room temperature. Different types of uniformly doped structures and digital alloys have been investigated. In contrast to GaSb:Mn films, ...

2009-04-15

394

Facile synthesis and the sensitized luminescence of europium ions-doped titanate nanowires  

International Nuclear Information System (INIS)

Europium (Eu) ions-doped titanate nanowires were synthesized via a sol-gel-hydrothermal chemistry and they were found to be roll multilayered trititanate-type nanowires intercalated with Eu3+ and alkali ions. The average diameter was about 20 nm for nanowires synthesized in NaOH solution and about 10 nm for nanowires synthesized in KOH solution. Under ultraviolet excitation the nanowires showed bright red emission corresponding to 5D0-7Fj of Eu3+ ions at room temperature, which was attributed to the non-radiative energy transfer from the surrounding Ti-O octahedral nanosheets to the central Eu3+ ions in interlayer. The luminescent properties of nanowires were influenced by the type of co-intercalated alkali ions, doping degree, hydrothermal and annealing temperatures. The intensity ratio of 5D0-7F2 to 5D0-7F1 of titanate nanowires intercalated with Eu3+ and Na+ ions was higher than that of titanate nanowires intercalated with Eu3+ and K+ ions. ...

2009-04-15

395

Analysis of TL glow curves in differently doped LiF:Mg,Ti  

International Nuclear Information System (INIS)

A computerised curve-fitting method was developed to calculate the trapping parameters in LiF TLD-100 and LiF:Mg, Ti. After irradiation in a "6"0Co field and with X rays emitted at different voltages the TL process is best described by first-order kinetics. A dependence of the trapping parameters on both the concentration of Mg and Ti and photon energy was detected. (author).

396

{sup 3}H-tetracycline as a proxy for {sup 41}Ca for measuring dietary perturbations of bone resorption  

Energy Technology Data Exchange (ETDEWEB)

Our group is interested in evaluating early effects of dietary interventions on bone loss. Postmenopausal women lose bone following reduction in estrogen which leads to increased risk of fracture. Traditional means of monitoring bone loss and effectiveness of treatments include changes in bone density, which takes 6 months to years to observe effects, and changes in biochemical markers of bone turnover, which are highly variable and lack specificity. Prelabeling bone with {sup 41}Ca and measuring urinary {sup 41}Ca excretion with accelerator mass spectrometry provides a sensitive, specific, and rapid approach to evaluating effectiveness of treatment. To better understand {sup 41}Ca technology as a tool for measuring effective treatments on reducing bone resorption, we perturbed bone resorption by manipulating dietary calcium in rats. We used {sup 3}H-tetracycline ({sup 3}H-TC) as a proxy for {sup 41}Ca and found that a single dose is feasible to study bone ...

2007-06-15

397

The use of calcium silicate bricks for retrospective dosimetry  

International Nuclear Information System (INIS)

The suitability of calcium silicate bricks (CSBs) for the retrospective measurement of gamma dose using luminescence techniques has been investigated. Bricks of this type are distinguished from fired clay bricks by containing negligible clay and requiring comparatively low temperature treatment during manufacture. They have been used widely in the construction f buildings in the Former Soviet Union since the 1970s but hitherto have not been used for retrospective dosimetry measurements. A procedure based on the se of the 210 deg. C thermoluminescence (TL) peak of quartz was tested with granular quartz extracted from three types of CSB, one of which had been taken from a settlement downwind of Chernobyl. The degree to which the residual geological TL signal within the temperature range of the 210 deg. C L peak had been reduced during manufacture varied with brick type; the levels of residual TL corresponded, in the samples tested, to absorbed doses n the range ...

2004-02-01

398

Production of hydrogen by radiolysis  

Energy Technology Data Exchange (ETDEWEB)

The possibility of obtaining high yields of hydrogen through the exposure of calcium hydroxide to natural uranium fission fragments is confirmed experimentally. The amounts of hydrogen obtained in some experiments were determined not only from the mass-spectrometry data, but also with the use of standard chemical analysis methods. The radiolytic hydrogen yield averaged over six independent experiments comprises 20.41 hydrogen molecules per 100 eV of absorbed fission fragment energy. The corresponding energy efficiency makes up to 60.62. Since on interaction with water or water vapor calcium hydroxide enters into the exothermal reaction to liberate 15.6 kcal/mole, it can easily be regenerated; this was attested to by one of irradiation experiments. Therefore, in the long run, we are dealing with a radiolytic decomposition of water at low temperatures or at temperatures readily available with modern reactor engineering techniques. Comparison of ...

1998-07-01

399

Macroscopic consequences of calcium signaling in microdomains: A first passage time approach  

CERN Document Server

Calcium (Ca) plays an important role in regulating various cellular processes. In a variety of cell types, Ca signaling occurs within microdomains where channels deliver localized pulses of Ca which activate a nearby collection of Ca-sensitive receptors. The small number of channels involved ensures that the signaling process is stochastic. The aggregate response of several thousand of these microdomains yields a whole-cell response which dictates the cell behavior. Here, we study analytically the statistical properties of a population of these microdomains in response to a trigger signal. We apply these results to understand the relationship between Ca influx and Ca release in cardiac cells. In this context, we use a first passage time approach to show analytically how Ca release in the whole cell depends on the single channel kinetics of Ca channels and the properties of microdomains. Using these results, we explain the underlying mechanism for the graded ...

2007-01-01

400

Lead and calcium distributions in blood, plasma, and milk of the lactating mouse  

Energy Technology Data Exchange (ETDEWEB)

Although it has been established that lead is transferred in milk from mother to suckling offspring, the physiological processes and parameters involved are not well understood. Single i.v. doses (0.2 mg/kg) or p.o. doses (2 mg/kg) of radiolabeled lead were administered to lactating and nonlactating female mice, and lead concentrations in blood, plasma, and milk were determined during a 21-day period. Large differences in lead elimination were observed between lactating and nonlactation mice. A significant fraction (25%) of the initial maternal dose (absorbed dose) was transferred to the suckling pups. The ratio of lead concentration in milk to lead concentration in plasma was found to be nearly constant over time. However, the milk-to-blood concentration ratios decreased during the same period. Furthermore, the concentration of lead in milk exceeded the plasma concentration by a factor of approximately 25, indicating that there is a physiological process(es) which establishes a large ...

1980-01-01

401

Human tooth enamel dissolution in citric acid as a function of degree of saturation and pH  

CERN Document Server

There is increasing concern among the dental community regarding the damage caused to teeth by the acids in soft drinks. Enamel dissolution in acidic solution can be reduced by addition of calcium and/or phosphate salts to increase the degree of saturation with respect to hydroxyapatite (DS sub H sub A), or by an increase in pH. In soft drinks, however, both of these approaches are associated with a reduced taste quality. The separate effects of each parameter are not known. In the work presented here, enamel dissolution was studied in citric acid solutions with compositions typical of soft drinks. Nanoindentation and atomic force microscopy (AFM) were used to investigate very early stages of enamel dissolution, with typical exposure times of 30-600 s. Preliminary investigations of the application of SIMS, ESEM and XPS to enamel dissolution studies are also reported. The individual effects of DS sub H sub A , pH and calcium and phosphate ...

2002-01-01

402

Development and performance of a miniature, high-voltage thermal battery  

Science.gov (United States)

A miniature, high-voltage, thermally activated battery has been developed. This battery weighs 41 grams, occupies a volume of 16.4 cu cm, and contains two separate 500-v channels, each designed to charge a 5.25 microfarad capacitor within 300 milli-seconds and remain operational under a 640-kohm load for a minimum of 28 seconds over the temperature range from +16 to +71 C. The electrochemical system utilizes a calcium anode, LiCl-KCl molten salt electrolyte, a CaCrO4-K2CrO4 mixture as the depolarizer or active cathode material, and an iron cathode. The depolarizer and electrolyte, along with a silica binder, are formed into homogeneous pellets, and these pellets are stacked alternately with calcium-iron bimetal disks in beryllium oxide tubes to form cell stacks. The cells are activated by an iron-potassium perchlorate pyrotechnic heat source external to the BeO tubes.

1974-01-01

403

Comparison of intrinsic and extrinsic tracer methods for estimating calcium bioavailability to rats from dairy foods  

International Nuclear Information System (INIS)

Dairy products doubly labeled with 45Ca and 47Ca were used to evaluate an extrinsic labeling procedure for calcium bioavailability determination. Nonfat milk, yogurt, and fresh cheese curd were prepared from caprine milk that was intrinsically labeled with 45Ca. The products were then labeled extrinsically with 47Ca and administered to rats by gavage. The 47Ca to 45Ca ratio in bone and teeth averaged about 1.00 with either milk, yogurt, or CaCl2, but the ratio was about 1.04 when dosed with cheese curd. Ca absorption, determined by whole-body counting of 47Ca, was lower (P less than 0.05) in cheese curd (59%) than in either milk (69%), yogurt (72%), or CaCl2 (72%). Expressed as percent of dose, the absorption of 47Ca was highly correlated with bone 47Ca (r = 0.973) and with bone 45Ca (r = 0.946). Correlation between tibia 47Ca and tibia 45Ca was r = 0.923. For the dairy products tested, our results indicated that extrinsic 47Ca was absorbed similarly to intrinsic ...

404

Analysis of lagoon sludge characteristics for choice of treatment process  

Energy Technology Data Exchange (ETDEWEB)

The Korea Atomic Energy Research Institute has launched a decommissioning program of uranium conversion plant. One of the important tasks in the decommissioning program is the treatment of the sludge, which was generated during operation and stored in the two ponds of the lagoon. The treatment requires the volume reduction of lagoon sludges for the low cost of the program and the conversion of the chemical forms, including uranium, for the acceptance at the final disposal site. The physical properties, such as densities, were measured and chemical compositions and radiological properties were analyzed. The denitration was a candidate process which would satisfy the requirements for sludge treatment, and the characteristics of thermal decomposition and dissolution with water were analyzed. The main compounds of the sludge were ammonium and sodium nitrate from conversion plant and calcium nitrate, calcium carbonate from Ca precipitation and ...

2002-04-01

405

A prospective randomised open label study to evaluate the potential of a new silver alginate/carboxymethylcellulose antimicrobial wound dressing to promote wound healing.  

Science.gov (United States)

The aim of this study was to observe both the clinical signs and symptoms of wounds at risk of infection, that is critically colonised (biofilm infected) and antimicrobial-performance of an ionic silver alginate/carboxymethylcellulose (SACMC) dressing, in comparison with a non silver calcium alginate fibre (AF) dressing, on chronic venous leg and pressure ulcers. Thirty-six patients with venous or pressure ulcers, considered clinically to be critically colonised (biofilm infected), were randomly chosen to receive either an SACMC dressing or a non silver calcium AF dressing. The efficacy of each wound dressing was evaluated over a 4-week period. The primary study endpoints were prevention of infection and progression to wound healing. The SACMC group showed a statistically significant (P = 0.017) improvement to healing as indicated by a reduction in the surface area of the wound, over the 4-week study period, compared with AF controls. In ...

2010-05-31

406

Ternary stannides RE_3Ru_4Sn_1_3 (RE = La, Ce, Pr, Nd). Structure, magnetic properties, and "1"1"9Sn Moessbauer spectroscopy  

International Nuclear Information System (INIS)

The ternary stannides RE_3Ru_4Sn_1_3 (RE = La, Ce, Pr, Nd) were obtained by arc-melting of the elements. The polycrystalline samples were characterized by powder X-ray diffraction. The structures of three compounds were refined from single-crystal diffractometer data: Yb_3Rh_4Sn_1_3 type, Pm anti 3n, a = 977.74(3) pm, wR2 = 0.0379, 280 F"2 values for La_3Ru_4Sn_1_3, a = 971.34(9) pm, wR2 = 0.0333, 274 F"2 values for Ce_3Ru_4Sn_1_3, a = 970.68(8) pm, wR2 = 0.0262, 272 F"2 values for Nd_3Ru_4Sn_1_3 with 13 variables per refinement. The structures consist of three-dimensional networks of condensed RuSn_6_/_2 trigonal prisms with the RE (CN 16) and Sn2 (CN 12) atoms in two different types of cavities of the networks. The two crystallographically independent tin sites have been resolved by "1"1"9Sn Moessbauer spectroscopy. Temperature-dependent magnetic susceptibility measurements of Ce_3Ru_4Sn_1_3 gave a reduced magnetic moment of 2.32 ?_B per Ce atom, indicating intermediate ...

2011-07-01

407

Spent fuel sabotage aerosol ratio program : FY 2004 test and data summary  

International Nuclear Information System (INIS)

This multinational, multi-phase spent fuel sabotage test program is quantifying the aerosol particles produced when the products of a high energy density device (HEDD) interact with and explosively particulate test rodlets that contain pellets of either surrogate materials or actual spent fuel. This program has been underway for several years. This program provides data that are relevant to some sabotage scenarios in relation to spent fuel transport and storage casks, and associated risk assessments. The program also provides significant technical and political benefits in international cooperation. We are quantifying the Spent Fuel Ratio (SFR), the ratio of the aerosol particles released from HEDD-impacted actual spent fuel to the aerosol particles produced from surrogate materials, measured under closely matched test conditions, in a contained test chamber. In addition, we are measuring the amounts, nuclide content, size distribution of the released aerosol materials, and enhanced ...

408

Local-density-functional approach to the isostructural #gamma#-#alpha# transition in cerium using the self-consistent linearized-augmented-plane-wave method  

International Nuclear Information System (INIS)

The isostructural #gamma#-#alpha# phase transition of Ce which occurs at 8 kbar has been studied by means of fully self-consistent (non-muffin-tin potential) linearized-augmented-plane-wave energy band calculations carried out for five different values of the lattice constant. In contradiction to the 4f electron promotional model of the transition, the results yield essentially one 4f electron to be occupied in each phase but with the 4f wave function somewhat less localized, and therefore more bandlike, in the ''collapsed'' #alpha# phase. A singly occupied 4f state is shown to be consistent with the available experimental data. These results strongly support the picture of a 4f localized bold-arrow-left-right itinerant transition at the #gamma#-#alpha# transition and conflict with the promotional model in which some fraction of 4f electrons are transferred to the sd conduction bands. The weaker bonding of the 4f electrons, compared to that of the 6s-5d valence electrons, accounts for ...

409

K/sub. beta. //K/sub. cap alpha. / transition probability ratios from the measurement of fluorescent X-ray intensities of some lanthanide compounds  

Energy Technology Data Exchange (ETDEWEB)

The effect that different chemical and physical atomic environments can have on the relative intensities of radiative electron transitions from the filling of K shell vacancies was investigated. The method used involved the detection of photoionization induced X-ray fluorescence. An experimental system based on a hyper pure germanium detector (HPGE) was used to measure the relative K-L and K-M X-ray yields from the photofluorescence of a series of lanthanide elements and compounds. A background subtraction and peak integration strategy was employed which accounted for scattering in the samples and scattering of the flux from the radioisotope photoionization sources. Analysis of the data resulted in a tabulation of relative K/sub ..beta..//K/sub ..cap alpha../ X-ray intensity ratios. The measured relative K/sub ..beta..//K/sub ..cap alpha../ X-ray intensity ratios were compared to the calculated values predicted by the theoretical development of Scofield and the average of previous ...

1987-01-01

410

K/sub #beta#//K/sub #alpha#/ transition probability ratios from the measurement of fluorescent X-ray intensities of some lanthanide compounds  

International Nuclear Information System (INIS)

The effect that different chemical and physical atomic environments can have on the relative intensities of radiative electron transitions from the filling of K shell vacancies was investigated. The method used involved the detection of photoionization induced X-ray fluorescence. An experimental system based on a hyper pure germanium detector (HPGE) was used to measure the relative K-L and K-M X-ray yields from the photofluorescence of a series of lanthanide elements and compounds. A background subtraction and peak integration strategy was employed which accounted for scattering in the samples and scattering of the flux from the radioisotope photoionization sources. Analysis of the data resulted in a tabulation of relative K/sub #beta#//K/sub #alpha#/ X-ray intensity ratios. The measured relative K/sub #beta#//K/sub #alpha#/ X-ray intensity ratios were compared to the calculated values predicted by the theoretical development of Scofield and the average of previous experimental values ...

1987-01-01

411

Extraction-spectrophotometric determination of terbium in its mixture with lanthanum  

International Nuclear Information System (INIS)

A spectrophotometric study of the extraction with isobutanol of rare-earth elements in the form of complexes with quinoilizarin and N-benzene-N-phenylhydroxylamine has been made. The purpose of the study is to find out whether this reaction can be used in determining the concentration of elements in the presence of other rare-earth elements. In determining the relationship between the pH and light absorption the pH of the solution is measured after the extraction. The extraction of complexes begins at pH approximately 4 and reaches a maximum at pH7-8 (for La) and pH6-9 (for Er). The complexes underge decomposition when pH of the solution increased. The composition of complex compounds is determined by spectrophotometric methods for isomolar series, molar ratios and from the slope of logarithmic plots. Under optimal conditions (pH7.5) aAd at the measured ratio of the component for each ion of rare-earth elements, the molar extinction coefficients are determined for complexes in ...

1975-01-01

412

Use of X-ray fluorescence analysis in the study of archeological samples  

International Nuclear Information System (INIS)

Radionuclide X-ray fluorescence analysis (XFA) was used in the determination of the contents of metal residues in dosing plates for coin minting. XFA was also used for the determination of the strontium/calcium ratio in bone samples of different animals with the aim to obtain information on the food composition of these animals. It was found that bones of different animals can be distinguished based on the Sr/Ca ratio. No significant differences in the Sr/Ca ratio were observed in human bones of individuals from different social groups. (author). 1 fig., 5 tabs., 4 refs.

1988-09-26

413

Use of Eu/sup 3 +/ as an oxygen environment probe in alkali-alkaline earth-lanthanide phosphates with the. beta. -K/sub 2/SO/sub 4/ structure  

Energy Technology Data Exchange (ETDEWEB)

The use of europium as a local structural probe allows the various phases appearing in the NaCaPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ and NaSrPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ systems to be detected. The broadening of the europium emission lines in going from the calcium to the strontium phases illustrates the ease of displacement of the PO/sub 4/ groups.

1983-09-15

414

The influence of amino acids on the biomineralization of hydroxyapatite in gelatin.  

Science.gov (United States)

The effects of pH on the calcium phosphate phase, of Tris and of amino acids, such as aspartic acid, glutamic acid, and serine on hydroxyapatite formation and morphology, were studied in double diffusion experiments. In this system, hydroxyapatite was only formed when the pH was around 7.4 or higher for the duration of the reaction. A decrease in pH resulted in the transformation of hydroxyapatite to octacalcium phosphate. Amino acids and Tris or the buffering capacity of Tris have an effect on the morphology of the synthetic hydroxyapatite. The presence of the additive results in spheres consisting of needles, blades or plates depending on the reaction system. PMID:12175941

2002-08-30

415

Selective detection of hexachromium ions by localized surface plasmon resonance measurements using gold nanoparticles/chitosan composite interfaces.  

Science.gov (United States)

Selective removal of hexavalent chromium ions from aqueous solutions using a chitosan/gold nanoparticles composite film was demonstrated. Localized surface plasmon resonance (LSPR) was used to measure the interface stability and detect the incorporation of chromium ions over time. The effects of pH, ethylenediaminetetraacetic acid (EDTA), and various foreign ions such as trivalent chromium, sodium, calcium, phosphate, sulfate and chloride on the adsorption of hexavalent chromium were investigated. PMID:19381379

2009-03-04

416

Radiostrontium in milk and tap water. Appendix D  

International Nuclear Information System (INIS)

Results of monitoring milk and tap water in New York City are presented. The New York City sample is a monthly composite of pasteurized milk purchased daily at retail stores. The monthly "9"0Sr to calcium ratios for New York City since the inception of the sampling program in 1954 are presented. Samples of New York City tap water are taken daily, so that by the end of the month, approximately 100 liters have been collected. The available cesium-137 data expressed as the "1"3"7Cs to "9"0Sr ratio are also given.

1980-01-01

417

Pitting corrosion of steel pipeline in oil-water-gas multiphase flow system  

Energy Technology Data Exchange (ETDEWEB)

Severe pitting corrosion occurred in a horizontal steel pipeline used to transport multiphase fluid, including water, oil, and natural gas, after 2 months of service. The pitting corrosion rate was up to 42 mm/year. Chemical analysis, X-ray diffractometry, and EDAX showed that the corrosion products mainly consisted of Fe9S8, FeCO3, and NaCl. Calcium containing inclusions were also found in the matrix of the steel, which may accelerate corrosion. The early failure was attributed to the high proportion of water, the slow flow velocity, and the use of unqualified material. (Author)

2000-07-01

418

New materials for SRS lasers  

International Nuclear Information System (INIS)

The problem of search for new materials for spectrally positioned laser sources, which is central for modern photonics, is discussed. The use of the stimulated Raman scattering effect in crystals offers a highly efficient way to the design of such sources. The recent results of investigations into this effect for a large number of various types of crystalline materials are presented. The most promising compounds, as regards the realisation of different laser operation modes, are considered, including calcium, strontium, barium and lead molybdates and tungstates. Several examples of functioning efficient lasers based on novel materials exhibiting the stimulated Raman light scattering effect are given.

2006-10-31

419

Models of cardiac electromechanics based on individual hearts imaging data  

British Library Electronic Table of Contents (United Kingdom)

Current multi-scale computational models of ventricular electromechanics describe the full process of cardiac contraction on both the micro- and macro- scales including: the depolarization of cardiac cells, the release of calcium from intracellular stores, tension generation by cardiac myofilaments, and mechanical contraction of the whole heart. Such models are used to reveal basic mechanisms of cardiac contraction as well as the mechanisms of cardiac dysfunction in disease conditions. In this paper, we present a methodology to construct finite element electromechanical models of ventricular contraction with anatomically accurate ventricular geometry based on magnetic resonance and diffusion tensor magnetic resonance imaging of the heart. The electromechanical model couples detailed repres...

2011-01-01

420

Mineral analysis in experimental corneal scars. An EDAX study  

Energy Technology Data Exchange (ETDEWEB)

Central penetrating excisional wounds were made in the corneas of 12 rabbits and 10 trout. The scar tissue and the surrounding cornea were compared using a new method for assessing inorganic elements in the cornea: the scanning electron microscopy and energy dispersive analysis of x-ray (EDAX). Semiquantitative determination of inorganic elements within the range of atomic numbers 9-93 in the periodic system was performed, comparing the relative concentration of those elements in the scar tissue to the surrounding cornea. Results showed that calcium was the only element higher in the healing wound than in the surrounding cornea.

1988-01-01

421

Mechanical Properties of Carbon Nanotubes / Hydroxyapatite Composites Prepared by Spark Plasma Sintering  

International Nuclear Information System (INIS)

In this study, Multi-Walled Carbon Nanotubes (MWCNTs) / Hydroxylapatite (HAp) composites were made to improve mechanical properties by using Spark Plasma Sintering (SPS) method. Slurry 6 mol of CaHPO4#centre dot#2H2O (DCPD), 4 mol calcium hydroxide and MWCNTs were mixed and sintered by using SPS at 5-120 MPa pressure, 1200-1250 deg. C and in vacuum or N2 atmosphere. The fracture toughness of sintered MWCNTs/HAp composites was increased.

2006-05-05

422

Fundamental investigation of duct/ESP phenomena. Final report  

Energy Technology Data Exchange (ETDEWEB)

Radian Corporation was contracted to investigate duct injection and ESP phenomena in a 1.7 MW pilot plant constructed for this test program. This study was an attempt to resolve problems found in previous studies and answer remaining questions for the technology using an approach which concentrates on the fundamental mechanisms of the process. The goal of the study was to obtain a better understanding of the basic physical and chemical phenomena that control: (1) the desulfurization of flue gas by calcium-based reagent, and (2) the coupling of an existing ESP particulate collection device to the duct injection process. Process economics are being studied by others. (VC)

1991-10-21

423

Fundamental investigation of duct/ESP phenomena  

Energy Technology Data Exchange (ETDEWEB)

Radian Corporation was contracted to investigate duct injection and ESP phenomena in a 1.7 MW pilot plant constructed for this test program. This study was an attempt to resolve problems found in previous studies and answer remaining questions for the technology using an approach which concentrates on the fundamental mechanisms of the process. The goal of the study was to obtain a better understanding of the basic physical and chemical phenomena that control: (1) the desulfurization of flue gas by calcium-based reagent, and (2) the coupling of an existing ESP particulate collection device to the duct injection process. Process economics are being studied by others. (VC)

1991-10-21

424

Elemental concentration analysis in some plant samples by EDXRF at Trabzon  

International Nuclear Information System (INIS)

The elemental analysis of some plant samples have been carried out in Trabzon region (Turkey) using energy-dispersive X-ray fluorescence (EDXRF) spectrometry. We have analyzed plant samples for nine stations using 1.85 GBq 55Fe radioactive sources. We have found that potassium and calcium within 0.3-1.4% and 0.3-2.8% were present in concentration in plants for every station, respectively. The concentration of Cl and Ti generally changed according to the plant species and the sampling station.

2006-12-01

425

CaSnO3:. a high capacity anode material for Li-ion batteries  

Science.gov (United States)

Calcium stannate (CaSnO3) powders with the distorted perovskite structure have been synthesized by solid state and the sol-gel methods and their electrochemical performance was compared. The sol-gel CaSnO3 shows stable cycling performance with a reversible capacity of 430-440 mAh/g (0.005-1.0 V; 60 mA/g) up to 50 cycles. The role of preparatory conditions, morphology and cycling conditions (current density and potential window) on the anodic performance of the compounds are addressed.

2002-12-01

426

Two Functional S100A4 Monomers Are Necessary for Regulating Nonmuscle Myosin-IIA and HCT116 Cell Invasion.  

Science.gov (United States)

S100A4, a member of the Ca(2+)-activated S100 protein family, regulates the motility and invasiveness of cancer cells. Moreover, high S100A4 expression levels correlate with poor patient survival in several cancers. Although biochemical, biophysical, and structural data indicate that S100A4 is a noncovalent dimer, it is unknown if two functional S100A4 monomers are required for the productive recognition of protein targets and the promotion of cell invasion. To address this question, we created covalently linked S100A4 dimers using a glycine rich flexible linker. The single-chain S100A4 (sc-S100A4) proteins exhibited wild-type affinities for calcium and nonmuscle myosin-IIA, retained the ability to regulate nonmuscle myosin-IIA assembly, and promoted tumor cell invasion when expressed in S100A4-deficient colon carcinoma cells. Mutation of the two calcium-binding EF-hands in one monomer, while leaving the other monomer intact, caused a ...

2011-07-13

427

Evaluation of calcification in pulmonary nodules using bone images obtained with single exposure energy subtraction  

Energy Technology Data Exchange (ETDEWEB)

Bone images obtained by single exposure dual energy subtraction with computed radiography, a new image processing method, were evaluated for the detectability of calcification in lung nodules in both phantom and clinical studies. In the phantom study, five simulated nodules containing known and uniformly distributed amounts of calcium hydroxide were placed in a human chest phantom and images were obtained the following five techniques: (1) conventional radiography (CXR), (2) low kV conventional radiography (Low), (3) Fuji computed radiography (FCR), (4) bone images with conventional singles exposure energy subtraction (ES) and (5) bone image with fine single exposure energy subtraction (FES). The detectability of calcification in the simulated nodules was evaluated by six radiologists using ROC analysis and two-way analysis of variance. In the clinical study, images of 42 lung nodules (21 calcified lung nodules and 21 non-calcified nodules), in which calcification ...

1995-08-01

428

Evaluation of calcification in pulmonary nodules using bone images obtained with single exposure energy subtraction  

International Nuclear Information System (INIS)

Bone images obtained by single exposure dual energy subtraction with computed radiography, a new image processing method, were evaluated for the detectability of calcification in lung nodules in both phantom and clinical studies. In the phantom study, five simulated nodules containing known and uniformly distributed amounts of calcium hydroxide were placed in a human chest phantom and images were obtained the following five techniques: 1) conventional radiography (CXR), 2) low kV conventional radiography (Low), 3) Fuji computed radiography (FCR), 4) bone images with conventional singles exposure energy subtraction (ES) and 5) bone image with fine single exposure energy subtraction (FES). The detectability of calcification in the simulated nodules was evaluated by six radiologists using ROC analysis and two-way analysis of variance. In the clinical study, images of 42 lung nodules (21 calcified lung nodules and 21 non-calcified nodules), in which calcification was ...

1995-01-01

429

Crystallographic data for new phases in the CaSO/sub 3/-H/sub 2/O system  

Energy Technology Data Exchange (ETDEWEB)

Among the three modifications of calcium sulfite hemihydrate, two of them, hexagonal ..beta..-CaSO/sub 3/.1/2H/sub 2/O with a rhombohedral lattice and ..gamma..-CaSO/sub 3/.1/2H/sub 2/O with a simple triangular hexagonal lattice, were found in the authors' recent work. By heating ..cap alpha..- and/or ..gamma..-hemihydrate at 330-360/sup 0/C in a nitrogen atmosphere, the orthorhombic anhydrate ..cap alpha..-CaSO/sub 3/ was formed, with lattice constants of 6.472, 15.93, and 23.44 angstrom for a, b, and c respectively, while the body-centered tetragonal anhydrate ..beta..-CaSO/sub 3/, with lattice constants of 15.68 and 19.44 angstrom for a and c respectively, was formed by heating the ..beta..-hemihydrate. The dehydration of three hemihydrates and the hydration of two anhydrates were discussed. Calcium sulfite hemihydrate (CaSO/sub 3/.1/2H/sub 2/O) is useful as an architectural material since it has a high thermal stability and a low ...

1982-03-01

430

Biological effects of exogenous adenosine 5 prime -triphosphate on cultured mammalian cells: Evidence for a receptor mechanism and its regulation by desensitization  

Energy Technology Data Exchange (ETDEWEB)

Exogenous adenosine 5{prime}-triphosphate (ATP) mobilized intracellular calcium in human carcinoma A43l cells and in Swiss 3T3 and 3T6 mouse fibroblasts by increasing inositol trisphosphate similar to well down growth factors (platelet-derived growth factor (PDGF), epidermal growth factor (EGF), bradykinin (BK), serum). Calcium mobilization was examined by video imaging of fura-2 fluorescence is single cells, following the radioactive isotope {sup 45}Ca, and monitoring the decrease in fluorescence of cells loaded with chlortetracycline. Uridine 5{prime}-triphosphate, but not other nucleotides, mimicked ATP. Single-cell analysis revealed synchronous responses in 10 sec to ATP, BK or serum, while PDGF (3T3) and EGF (A431) produced slower signals with significant cell-to-cell variation. PDGF desensitized 3T3 cells to ATP and BK added 100 sec later but ATP or BK did not desensitized to PDGF. Homologous desensitization was seen with all agonists. ...

1989-01-01

431

Stabilization of high-temperature antimony oxide with molybdenum incorporation. Structure of Mo-doped Sb/sub 2/O/sub 4/ by powder neutron diffraction and extended X-ray absorption fine structure spectroscopy  

Energy Technology Data Exchange (ETDEWEB)

It has been discovered that the presence of MoO/sub 3/ lowers the ..cap alpha..-..beta.. transition in Sb/sub 2/O/sub 4/ from 935 to 850/sup 0/C with concurrent dissolution of Mo in the high-temperature (..beta..) form. The structure of Mo-doped ..beta..-Sb/sub 2/O/sub 4/ has been investigated by powder neutron diffraction, extended X-ray absorption fine structure (EXAFS) and Raman spectroscopies, and scanning-electron microscopy (SEM). Cell parameters: a = 12.0571 (12) A, b = 4.8335 (1) A, c = 5.3838 (6) A, ..beta.. = 105.579 (5)/sup 0/, monoclinic, space group C2/c, Z = 4. Combining the results of these techniques leads to the hypothesis that Mo is located interstitially within channels of electron density in the Sb/sub 2/O/sub 4/ structure with concurrent vacancy of two Sb/sup III/ atoms. There is no apparent oxygen deficiency in the resulting structure. 25 references, 6 figures, 3 tables.

1985-10-09

432

Radiation damage studies on CrO_4"2"- doped alums  

International Nuclear Information System (INIS)

Radiation damage studies have been carried out on undoped and CrO_4"2"- doped potassium and ammonium alums. The optical absorption bands observed around 27100 and 36500 cm"-"1 before irradiation have been attributed to the transitions t_1 #-># e and t_1 #-># t_2, on the basis of Ball-hausen and Liehr scheme. On prolonged X-irradiation, these bands disappear in both the alums and three new bands seem to grow in ammonium alum while only two new bands could be seen in potassium alum. EPR studies at RT reveal that there are two lines at g = 2.004 and g = 2.010 in ammonium alum and only one line at g = 2.004 in potassium alum. Besides these two nearly isotropic lines, there is a set of lines around g = 1.95 in both the alums. Correlating the optical and EPR studies it is concluded that SO_3"- and O_3"- centres have formed on X-irradiation in ammonium alum while only SO_3"- seems to have formed in potassium alum. The most important feature is the formation of a new ...

433

Preparation of a high-J sub c YBCO bulk superconductor by the platinum doped melt growth method  

Energy Technology Data Exchange (ETDEWEB)

Recently we have found a highly effective additive for the melt growth processings attaining high critical currents in YBCO superconductor. It is platinum and it behaves as an effective grain growth inhibitor for the Y{sub 2}BaCuO{sub 5} phase. Even with less than 1 wt.% doping, Y{sub 2}BaCuO{sub 5} particles becomes less than one micron in size and distribute themselves to become homogeneously embedded in the large grown YBa{sub 2}Cu{sub 3}O{sub y} grains. The sample shows large magnetic hysteresis and a typical J{sub c} value estimated by using Bean's model critical state model is 18000 A/cm{sup 2} at 77 K and 1 T. We found that rhodium has a similar remarkable effect. (orig.).

1991-06-15

434

Preparation and photocatalytic property of pyrochlore Bi{sub 2}Ti{sub 2}O{sub 7} and (Bi, La) {sub 2}Ti{sub 2}O{sub 7} films  

Energy Technology Data Exchange (ETDEWEB)

Dopant-free Bi{sub 2}Ti{sub 2}O{sub 7} thin films with pyrochlore structure and La-doped bismuth titanate thin films have been fabricated by means of chemical solution decomposition, and characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy and UV-Vis spectrophotometry in this study. Their photocatalytic activities have been evaluated by photodegrading methyl orange solution, and the optimum processing parameters for the highest photocatalytic activity have been found. Moreover, the effects of La-doping on the phase transformation and the photocalalytic activity have been studied. It has been deduced from the experiment result that substituted La{sup 3+} ions can act as a stabilizer of Aurivillus phase BLT and a grain-growth inhibitor in BLT thin films.

2008-11-28

435

Polysilicon thin film transistors fabricated on low temperature plastic substrates  

Energy Technology Data Exchange (ETDEWEB)

We present device results from polysilicon thin film transistors (TFTs) fabricated at a maximum temperature of 100&hthinsp;{degree}C on polyester substrates. Critical to our success has been the development of a processing cluster tool containing chambers dedicated to laser crystallization, dopant deposition, and gate oxidation. Our TFT fabrication process integrates multiple steps in this tool, and uses the laser to crystallize deposited amorphous silicon as well as create heavily doped TFT source/drain regions. By combining laser crystallization and doping, a plasma enhanced chemical vapor deposition SiO{sub 2} layer for the gate dielectric, and postfabrication annealing at 150&hthinsp;{degree}C, we have succeeded in fabricating TFTs with I{sub ON}/I{sub OFF} ratios {gt}5{times}10{sup 5} and electron mobilities {gt}40 cm{sup 2}/V&hthinsp;s on polyester substrates. {copyright} {ital 1999 American Vacuum Society.}

1999-07-01

436

Photoluminescence of europium doped LiInO2 powder  

British Library Electronic Table of Contents (United Kingdom)

Abstract Lithium-indium oxide is one of the candidate materials as solid-state scintillators for solar neutrinos due to an inverse --decay of 115In to 115Sn. On the other hand, when doped with rare-earth ions such as Eu3+ or Sm3+, it becomes a promising phosphor material. In this report we present a simple solid-state procedure for preparation of LiInO2:Eu3+ powders. X-ray diffraction confirmed prod-uct in tetragonal structural form (space group: I41/amd) and no impurity phases were detected. Then, high resolution photoluminescence emission measurements were performed at room and low temperatures to find 5D0 - 7FJ. Emission kinetics from 5D0 level exhibited pure single exponential behavior with lifetime of about 1.5 ms. Maximum energy splitting of 7F1 manifold is recorded as a function of ...

2011-01-01

437

Modeling of the relaxation kinetics of metastable tensile strained Si:C alloys  

Energy Technology Data Exchange (ETDEWEB)

In order to enhance the performance of CMOS transistors, embedded epitaxial layers of Si:C can be used. In the present work, Si:C layers with Carbon contents up to 1.9 at-% and in-situ Phosphorus doping up to 4 x 10{sup 20}At/cm{sup 3} have been investigated. Due to the low solubility of Carbon in Silicon (0.0004 at.-% at the melting point), all layers considered in this work are metastable and tend to relax. Since it is crucial to the application to retain the strain of those layers, the responsible mechanisms must be understood. The relaxation during thermal treatment was studied by high resolution X-ray diffraction and was found to behave differently, depending on Carbon content and Phosphorus doping concentration. In this work, we propose a relaxation mechanism based on a kick-out reaction of substitutional Carbon which is accelerated by Phosphorus content through transient enhanced diffusion. We simulate the time evolution of layer ...

2010-07-01

438

Lanthanum gallate and ceria composite as electrolyte for solid oxide fuel cells  

International Nuclear Information System (INIS)

The composite of doped lanthanum gallate (La_0_._9Sr_0_._1Ga_0_._8Mg_0_._2O_2_._8_5, LSGM) and doped ceria (Ce_0_._8Sm_0_._2O_1_._9, CSO) was investigated as an electrolyte for solid oxide fuel cell (SOFC). The LSGM-CSO composite was examined by X-ray diffraction (XRD) and impedance spectroscopy. It was found that the sintered LSGM-CSO composite contains mainly fluorite CeO_2 phase and a minority impurity phase, Sm_3Ga_5O_1_2. The LSGM-CSO composite electrolyte shows a small grain boundary response in the impedance spectroscopy as compared to LSGM and CSO pellets. The composite electrolyte exhibits the highest conductivity in the temperature range of 250-600 "oC, compared to LSGM and CSO. The LSGM-CSO composite can be expected to be an attractive intermediate temperature electrolyte material for solid oxide fuel cells.

2010-03-04

439

Inverse spinel materials. A new class of high voltage cathode materials for Li-ion batteries  

Energy Technology Data Exchange (ETDEWEB)

The influence of Cr on the structure and electrochemical properties of LiCoVO{sub 4} was studied using X-Ray diffraction, scanning electron microscopy, Raman Spectroscopy and cycle tests. Doping levels up to 10 mol% were achieved, which improved the electrochemical stability of the structure of LiCoVO{sub 4}, resulting in a significant increase in the initial charge and discharge capacity. The Raman spectroscopy data for the Cr-doped LiCoVO{sub 4} is similar as for LiCoVO{sub 4}. The replacement of a dopant for the Co-ion in the inverse spinel structure causes several Raman shifts. The X-ray diffraction patterns show no new phases and combined with the Raman spectroscopy data it is concluded that the Cr dopant will be located at the octahedral site (16d) where they create an electronic pathway that enhances the electronic conductivity. However, the capacity dropped significantly after prolonged cycling, which is due to the diffusion of V{sup ...

2003-07-01

440

Influence of high energy electron irradiation on the characteristics of polysilicon thin film transistors  

Energy Technology Data Exchange (ETDEWEB)

The influence of high energy electron (23 MeV) irradiation on the electrical characteristics of p-channel polysilicon thin film transistors (PSTFTs) was studied. The channel 220 nm thick LPCVD (low pressure chemical vapor deposition) deposited polysilicon layer was phosphorus doped by ion implantation. A 45 nm thick, thermally grown, SiO{sub 2} layer served as gate dielectric. A self-alignment technology for boron doping of the source and drain regions was used. 200 nm thick polysilicon film was deposited as a gate electrode. The obtained p-channel PSTFTs were irradiated with different high energy electron doses. Leakage currents through the gate oxide and transfer characteristics of the transistors were measured. A software model describing the field enhancement and the non-uniform current distribution at textured polysilicon/oxide interface was developed. In order to assess the irradiation-stimulated changes of gate oxide parameters the gate ...

2006-08-15

441

Influence of high energy electron irradiation on the characteristics of polysilicon thin film transistors  

International Nuclear Information System (INIS)

The influence of high energy electron (23 MeV) irradiation on the electrical characteristics of p-channel polysilicon thin film transistors (PSTFTs) was studied. The channel 220 nm thick LPCVD (low pressure chemical vapor deposition) deposited polysilicon layer was phosphorus doped by ion implantation. A 45 nm thick, thermally grown, SiO_2 layer served as gate dielectric. A self-alignment technology for boron doping of the source and drain regions was used. 200 nm thick polysilicon film was deposited as a gate electrode. The obtained p-channel PSTFTs were irradiated with different high energy electron doses. Leakage currents through the gate oxide and transfer characteristics of the transistors were measured. A software model describing the field enhancement and the non-uniform current distribution at textured polysilicon/oxide interface was developed. In order to assess the irradiation-stimulated changes of gate oxide parameters the gate oxide ...

2006-08-01

442

Hydrothermal synthesis of semiconductive PZT solid solutions and electromechancal properties of sintered bodies. Suinetsuho ni yoru handosei PZT koyotai no gosei to shoketsutai no denki kikaiteki seishitsu  

Energy Technology Data Exchange (ETDEWEB)

Semiconductive crystalline PZT powders doped with Bi and K were synthesized by hydrothermal reaction at 200{degree}C for 48 hours. The synthesis of the crystalline powders became difficult with an increase in doped amount of Bi and K, and in Zr/(Ti+Zr) ratio. Since substantial amounts of Pb remained in solution after hydrothermal reaction, the addition of Pb in excess of 25% was necessary to obtain the stoichiometric composition of the PZT solid solution. Bi contents in the powders were identical to those in starting materials, while K contents were less than expected ones. The electromechanical properties of the sintered bodies could be precisely measured by an admittance-curve-fitting method. The electromechanical coupling factor and piezoelectric coefficient of the sintered bodies varied with the Bi content like those of specimens prepared by solid state reaction, and showed the maximum values at a given Bi content. However, the change in ...

1989-10-01

443

High-performance thin-film transistors fabricated using excimer laser processing and grain engineering  

Energy Technology Data Exchange (ETDEWEB)

High-performance polysilicon thin-film transistors (TFT`s) are fabricated using an excimer laser to recrystallize the undoped channel and dope the source-drain regions. Using a technique the authors call grain engineering they are able to control grain microstructure using laser parameters. Resulting polysilicon films are obtained with average grain sizes of {approximately}4--9 {micro}m in sub-100 nm thick polysilicon films without substrate heating during the laser recrystallization process. Using a simple four-mask self-aligned aluminum top-gate structure, they fabricate TFT`s in these films. By combining the grain-engineered channel polysilicon regions with laser-doped source-drain regions, TFT`s are fabricated with electron mobilities up to 260 cm{sup 2}/Vs and on/off current ratios greater than 10{sup 7} To their knowledge, these devices represent the highest performance laser-processed TFT`s reported to date fabricated without substrate ...

1998-04-01

444

High field ESR of P-doped Si for Quantum Computing Application  

Energy Technology Data Exchange (ETDEWEB)

We measured ESR of phosphorous-doped silicon with a low concentration of P, n, at high magnetic fields and low temperatures to investigate the states of nuclear spin. A sample with n = 6.52 x 10{sup 16} /cm{sup 3} was studied at 2.85 T (80 GHz) from 30 K to 2.3 K by field-modulating cw-ESR for a fixed 0 dB power. As the temperature was lowered, the out-of-phase signal appeared around 18 K, reached at a maximum intensity at 13 K, and disappeared around 6 K. The out-of-phase signal is referred to the field modulation. The in-phase signal started to change from the derivative of absorption spectrum at high temperatures to absorption-like shape around 15 K and asymmetry of intensity for two peaks of hyperfine-separated signals increased as temperatures was lowered. Below 10 K, the saturation of the in-phase signal started to appear. We speculate that the asymmetry is caused by saturation effect and dynamic nuclear polarization of {sup 31}P nuclear spin due to drastic ...

2009-02-01

445

GaAs Blocked-Impurity-Band Detectors for Far-Infrared Astronomy  

Energy Technology Data Exchange (ETDEWEB)

High-purity and doped GaAs films have been grown by Liquid-phase epitaxy (LPE) for development of a blocked impurity band (BIB) detector for far-infrared radiation. The film growth process developed has resulted in the capability to grow GaAs with a net active impurity concentration below 1 x 10{sup 13} cm{sup -3}, ideal for the blocking layer of the BIB detector. The growth of n-type LPE GaAs films with donor concentrations below the metal-insulator transition, as required for the absorbing layer of a BIB detector, has been achieved. The control of the donor concentration, however, was found to be insufficient for detector production. The growth by LPE of a high-purity film onto a commercially grown vapor-phase epitaxial (VPE) n-type GaAs doped absorbing layer resulted in a BIB device that showed a significant reduction in the low-temperature dark current compared to the absorbing layer only. Extended optical response was not detected, most ...

2004-12-21

446

Electron spin resonance investigation of Mn^{2+} ions and their dynamics in manganese doped SrTiO_3  

CERN Document Server

Using electron spin resonance, lattice position and dynamic properties of Mn2+ ions were studied in 0.5 and 2 % manganese doped SrTiO3 ceramics prepared by conventional mixed oxide method. The measurements showed that Mn2+ ions substitute preferably up to 97 % for Sr if the ceramics is prepared with a deficit of Sr ions. Motional narrowing of the Mn2+ ESR spectrum was observed when temperature increases from 120 K to 240-250 K that was explained as a manifestation of off-center position of this ion at the Sr site. From the analysis of the ESR spectra the activation energy Ea = 86 mV and frequency factor 1/?0 ? (2-10)x10^(-14) 1/s for jumping of the impurity between symmetrical off-center positions were determined. Both values are in agreement with those derived previously from dielectric relaxation. This proves the origin of dielectric anomalies in SrTiO3:Mn as those produced by the reorientation dynamics of Mn2+ dipoles.

2007-01-01

447

Electrogenerated chemiluminescence sensor for metoclopramide determination based on Ru(bpy)32+-doped silica nanoparticles dispersed in Nafion on glassy carbon electrode  

British Library Electronic Table of Contents (United Kingdom)

A novel method for the determination of metoclopramide (MCP) using electrogenerated chemiluminescence (ECL) is presented. A tris(2,2prime-bipyridyl)dichlororuthenium(II) (Ru(bpy)32+)-doped silica (RuDS) nanoparticle/perfluoinated ion-exchange resin (Nafion) with nanocomposite membrane modified glassy carbon electrode (GCE) is used. The Ru(bpy)32+ encapsulation interior of the silica nanoparticle maintains its electrochemical activities and also reduces Ru(bpy)32+ leaching from the silica matrix when immersed in water due to the electrostatic interaction. The analytical performance of this ECL sensor for MCP is shown in detail. Under optimal experimental conditions, it has good linearity in the concentration range from 2x10-8mol/L to 1x10-5mol/L (R=0.9989) with a detection limit of 7x10-9mo...

2008-01-01

448

Doping of silicon carbide by ion implantation  

Energy Technology Data Exchange (ETDEWEB)

A brief survey is given of some recent results on doping of 4H- and 6H-SiC by ion implantation. The doses and energies used are between 10{sup 9} and 10{sup 15} cm{sup -2} and 100 keV and 5 MeV, respectively, and B and Al ions (p-type dopants) are predominantly studied. After low dose implantation ({<=}10{sup 10} cm{sup -2}) a strong compensation is observed in n-type samples and this holds irrespective of implantation temperature up to 600 C. However, at higher doses (10{sup 14}-10{sup 15} Al/cm{sup 2}) the rate of defect recombination (annihilation) increases substantially during hot implants ({>=}200 C), and in these samples one type of structural defect dominates after post-implant annealing at 1700-2000 C. The defect is identified as a dislocation loop composed of clustered interstitial atoms inserted on the basal plane in the hexagonal crystal structure. Finally, transient enhanced diffusion (TED) of ion-implanted boron in 4H-samples is ...

2001-07-01

449

Alkaline doped TiO2 sol-gel catalysts: Effect of sintering on catalyst activity and selectivity for acetone condensation  

British Library Electronic Table of Contents (United Kingdom)

In this paper, we prepared by the sol-gel method alkaline titania catalysts, doped by gelling titanium alkoxide with aqueous solutions containing potassium, rubidium or cesium chlorides. XRD patterns showed that samples annealed at 400 and 600degreeC contained a single crystalline phase, anastase. Specific surface areas were higher in samples annealed at 400degreeC (>100m2/g) than in those annealed at 600degreeC (25m2/g). The weight density of basic sites determined by CO2-TPD drastically diminished in samples treated at 600degreeC. Catalysts were tested for the self-condensation of acetone at 300degreeC; main reaction products were isomesityl oxide, mesityl oxide and mesitylene. Samples annealed at 600degreeC showed lower acetone conversion rate and low formation of mesitylene than that o...

2006-01-01

450

Visible semiconductor lasers with the AlGaInP materials system  

International Nuclear Information System (INIS)

The AlGaInP materials system has recently supported the development of a variety of visible diode laser devices at wavelengths ranging from yellow to red. Presently, the majority of published results are with materials prepared by organometallic vapor phase epitaxy (OMVPE). Many issues with such materials exist, including impurity doping, the role of crystal ordering, defect formation during epitaxial growth, and the proper quantum well heterostructure design required for best device results. This paper addresses these topics and reviews the present state of the art, and projects the anticipated results when the materials' problems have been solved.

1988-11-02

451

The rare earth antimonates: spectroscopic properties, crystal field and paramagnetic susceptibility simulations  

Energy Technology Data Exchange (ETDEWEB)

The rare earth antimonates RE{sub 3}Sb{sub 5}O{sub 12} constitute an isostructural series, where the rare earth site symmetry is S{sub 4}. The spectroscopic properties of pure or doped compounds of this family are studied in order to derive their energy level schemes and to simulate them through the crystal field theory, by using the approximated D{sub 2d} potential. The paramagnetic susceptibilities are calculated with the derived wavefunctions and compared to experiment.

1991-01-01

452

The hunt for ?13 at the Daya Bay nuclear power plant  

International Nuclear Information System (INIS)

The Daya Bay reactor neutrino experiment is located at the Daya Bay nuclear power plant in Shenzhen, China. The experiment deploys eight 'identical' antineutrino detectors to measure antineutrino fluxes from six 2.9 GWth reactor cores in three underground experimental halls at different distances. The target zone of the Daya Bay detector is filled with 20 t 0.1% Gd doped LAB liquid scintillator. The baseline uncorrelated detector uncertainty is ?0.38% using current experimental techniques. Daya Bay can reach a sensitivity of sin22?13<0.01 with baseline uncertainties after 3 years of data taking.

2010-03-30

453

The effect of temperature on the radiative performance of Ho-YAG thin film selective emitters  

Energy Technology Data Exchange (ETDEWEB)

The authors present the emitter efficiency results for the thin film 25 percent Ho YAG (Yttrium Aluminum Garnet, Y3Al5O12) selective emitter from 1000 to 1700 K with a platinum substrate. Spectral emittance and emissive power measurements were made (1.2 less than lambda less than 3.2 microns) and used to calculate the radiative efficiency. The radiative efficiency and power density of rare earth doped selective emitters are strongly dependent on temperature and experimental results indicate an optimum temperature (1650 K for Ho YAG) for thermophotovoltaic (TPV) applications.

1995-01-01

454

Synthesis and scintillation properties of GdCl_3:Ce"3"+ (Gd_1_-_xCe_xCl_3_,x = 0.005-0.08)  

International Nuclear Information System (INIS)

Single crystals of GdCl_3 doped with different concentrations of Ce"3"+ have been grown using the Bridgman-Stockbarger technique and their luminescence and scintillation properties were investigated. The luminescence spectrum of GdCl_3:Ce"3"+ is complex and consists of two bands with maxima at 350 nm and 370 nm. The maximal light yield in GdCl_3:Ce"3"+ was observed at #approx#1 mol% of Ce"3"+ (more than 38 000 ph/MeV).

2009-07-08

455

Simple integral screenprinting process for selective emitter polycrystalline silicon solar cells  

Energy Technology Data Exchange (ETDEWEB)

This letter describes a new simple fabrication process, developed recently for blue response'' improvement in low-cost polycrystalline silicon solar cells. A selective emitter is created by heavily doping the emitter, followed by a wet etching-back of the cell area between the fingers. An improvement up to 17 mV in {ital V}{sub oc}, 1.5 mA/cm{sup 2} in {ital J}{sub sc}, and 1% (absolute value) in {eta} is obtained. Effective phosphorus gettering, self-alignment, and application in a low-cost full screenprinting technology are the main advantages of the proposed process.

1991-09-23

456

Relations between structural and superconducting properties of bulk and thin film high-T_c materials  

International Nuclear Information System (INIS)

The structural ordering of oxygen deficient and Co-doped YBCO (YBa_2Cu_3_-_yCo_yO_6_+_x) have been studied experimentally, and by computer simulations of the oxygen ordering in the basal plane of the structure. The calculations are based on the two-dimensional ASYNNNI model and its modifications. Good agreement is established between the ASYNNNI calculations and the experimentally observed structural properties of the double cell ortho-II structure and the oxygen disordering process from Co-doping into the basal plane. A model that relates the superconducting transition temperature T_c(x) of undoped YBCO and T_c(y) of Co-doped YBCO to the formation of specific domains of the two orthorhombic ordered oxygen phases, ortho-I and ortho-II, shows a close agreement with experimental T_c(x) and T_c(y) data of samples prepared under equilibrium conditions. The structural changes as a result of metal ion substitutions and ...

1984-02-13

457

Polysilicon TFT fabrication on plastic substrates  

Energy Technology Data Exchange (ETDEWEB)

Processing techniques utilizing low temperature depositions and pulsed lasers allow the fabrication of polysilicon thin film transistors (TFT`s) on plastic substrates. By limiting the silicon, SiO2, and aluminum deposition temperatures to 100(degrees)C, and by using pulsed laser crystallization and doping of the silicon, we have demonstrated functioning polysilicon TFT`s fabricated on polyester substrates with channel mobilities of up to 7.5 cm2/V-sec and Ion/Ioff current ratios of up to 1x10(to the 6th power).

1997-08-06

458

Plasma immersion ion implantation. (Latest citations from the EI Compendex*plus database). Published Search  

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning plasma immersion ion implantation (PIII) and equipment. PIII is a new technique to implant plasma ions into materials for surface modification and treatment. Topics include plasma nitriding, semiconductor doping, ion energy distribution, ion dose, pulsed plasma, metal plasma, and defect passivation. References also review applications in semiconductor device and integrated circuit manufacture, silicon material fabrication, aerospace bearings, carbon coatings on metals, and ceramic coatings. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

1998-01-01

459

Phytic acid doped nanoparticles for green anticorrosion coatings  

British Library Electronic Table of Contents (United Kingdom)

In this paper, an environmentally friendly metal corrosion inhibitor, phytic acid, was assembled into the walls of silica nanoparticles via layer-by-layer self-assembly technique (LbL) with poly(allylamine hydrochloride). Such functionalized nanoparticles were uniformly distributed into sol-gel films for metal anticorrosion. The films showed very pronounced and lasting protective efficiency in concentrated salt aqueous solutions as indicated by electrochemical impedance spectroscopy (EIS) measurement. These results may provide a new route for the preparation of environment-friendly anticorrosion coatings.

2010-01-01

460

Photoluminescence of manganese- and copper-doped CdS nanowires  

Energy Technology Data Exchange (ETDEWEB)

Arrays of CdS:Mn{sup 2+}:Cu{sup +} micro- and nanowires grown in polycarbonate ion-track templates exhibit photoluminescence in the spectral domain ranging from 500 to 800 nm at room temperature. A comparison with similar CdS and CdS:Mn{sup 2+} wire arrays is presented. The individual contributions to the emission spectra of Cu{sup +} and Mn{sup 2+} ions in the CdS matrix are explained using their energy level schemes. Also SEM, EDX and EPR data are given for these wires. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

2005-02-01

461

Photoluminescence of manganese- and copper-doped CdS nanowires  

International Nuclear Information System (INIS)

Arrays of CdS:Mn"2"+:Cu"+ micro- and nanowires grown in polycarbonate ion-track templates exhibit photoluminescence in the spectral domain ranging from 500 to 800 nm at room temperature. A comparison with similar CdS and CdS:Mn"2"+ wire arrays is presented. The individual contributions to the emission spectra of Cu"+ and Mn"2"+ ions in the CdS matrix are explained using their energy level schemes. Also SEM, EDX and EPR data are given for these wires. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

2005-02-01

462

Phase formation in gas-phase combustion and pyrolysis reactions under spark and radio-frequency discharge conditions  

British Library Electronic Table of Contents (United Kingdom)

Doped ultrafine silicon dioxide powder with a narrow particle size distribution was obtained by RF discharge-stimulated dichlorosilane (SiH2C) oxidation at a low pressure using isobutylene as the combustion inhibitor and chromium hexacarbonyl (Cr(CO)6) as the dopant. The formation and morphology of the ultrafine particles are governed by the parameters of the RF discharge and by the chemical mechanism of the combustion reaction yielding the aerosol. Submicron-sized filamentous carbon structures can be obtained by isobutylene decomposition under spark discharge conditions in the presence of a molybdenum metal catalyst.

2009-01-01

463

Nuclear borehole logging using lithium detector assemblies  

International Nuclear Information System (INIS)

A method and apparatus for nuclear borehole logging, and in particular, neutron porosity logging, uses a neutron source, and a pair of spaced lithium detectors, preferably Li"6I crystal or Li"6 doped glass, to detect neutrons emitted from a borehole formation being logged. The spectrum developed by the lithium detectors is processed to remove the gamma ray background radiation and the hydrogen absorption peak, thus allowing a more accurate neutron count. A Gaussian curve is fitted to the neutron peak of the spectrum, the curve eliminating the hydrogen absorption peak. The area under this Gaussian curve represents the neutron count. (author).

1991-11-01

464

Mechanisms of Alloy 800 corrosion in helium  

International Nuclear Information System (INIS)

Cr_2O_3 scales are found to form on Alloy 800 and a similar pure ternary alloy in air, and 1 and 50 atm. helium containing oxidizing impurities typical of those in an SGHTR. The strong temperature dependence and neglibible helium overpressure dependence indicate that gas transport through the scales is not rate controlling. Surface oxidation rates are therefore controlled by solid state diffusion and the low oxygen partial pressure dependence of the oxidation rate in Alloy 800 is ascribed to the presence of extrinsic defects in the Cr_3O_3 (due to doping by alloying elements) or to the presence of short circuit diffusion paths. (Auth.).

465

Magnetic structure of Ce(Ru_0_._9_6Pd_0_._0_4)_2Si_2  

International Nuclear Information System (INIS)

The magnetic structure of a tetragonal Ce(Ru_0_._9_6Pd_0_._0_4)_2Si_2 single crystal, determined by neutron diffraction measurements, is similar to that observed in Rh doped alloys. The magnetic moments are oriented and modulated along the c-axis. Here the wave vector is incommensurate: k=(0,0,0.38). At 1.5 K, the moment is estimated to about 0.3 #mu#_B. Magnetization, magnetoresistance and Hall effect measurements performed on this alloy are also reported. (orig.).

466

Interstitial injection in silicon after high-dose, low-energy arsenic implantation and annealing  

International Nuclear Information System (INIS)

In this work, we investigate the interstitial injection into the silicon lattice due to high-dose, low-energy arsenic implantation. The approach consists in monitoring the diffusion of the arsenic profile as well as of the boron profile in buried #delta#-doped layers, when amounts of the as-implanted arsenic profile are removed by low-temperature wet silicon etching. The experimental results indicate that the contribution of the implantation damage to the transient enhanced diffusion of boron, and thus the interstitial injection, is not the main one. On the contrary, interstitial generation due to arsenic clustering seems to be more important for the present conditions.

2005-11-14

467

Infrared spectroscopy analysis of MgO-doped silicon nitride  

Energy Technology Data Exchange (ETDEWEB)

Silicon nitride hybrid ball bearings used in high temperature applications undergo mechanical and environmental degradation. To study the surface chemistry of silicon nitride, a CAChe{trademark} Worksystem* has been used to generate the clusters and corresponding transmission vibrational spectra of silicon nitride. In the present study, the effect of surface conditions on the surface chemistry and wear degradation of silicon nitride was evaluated. Infrared reflection spectroscopy (IRRS) used to determine molecular orientations shows a difference in reflectance spectra for fractured and as-received.

1997-12-31

468

High emittance coverglass  

International Nuclear Information System (INIS)

The authors describe measurements of emittance made on samples of solar cell coverglasses incorporating new coatings both on C-7940 fused silica and on CMX ceria doped microsheet. Samples of a conventional, MgF_2 coating on the same two types of coverglass substrates were included in the measurements as controls. Measurements were made by the calorimetric method of total hemispherical emittance within a cooled chamber as well as by the more common infrared reflectance method. Emittance enhancements from 1 to 4% were measured for the new coatings.

1988-09-26

469

Functionalized luminescent oxide nanoparticles for sodium channel imaging at the single molecule level  

Science.gov (United States)

Lanthanide-ion doped oxide nanoparticles were functionalized for use as fluorescent biological labels. These nanoparticles are synthesized directly in water which facilitates their functionalization, and are very photostable without emission intermittency. Nanoparticles functionalized with guanidinium groups act as artificial toxins and specifically target sodium channels. They are individually detectable in cardiac myocytes, revealing a heterogeneous distribution of sodium channels. Functionalized oxide nanoparticles appear as a novel tool particularly well adapted to long-term single-molecule tracking.

2005-04-01

470

Emittance theory for thin film selective emitter  

Energy Technology Data Exchange (ETDEWEB)

Thin films of high temperature garnet materials such as yttrium aluminum garnet (YAG) doped with rare earths are currently being investigated as selective emitters. This paper presents a radiative transfer analysis of the thin film emitter. From this analysis the emitter efficiency and power density are calculated. Results based on measured extinction coefficients for erbium-YAG and holmium-YAG are presented. These results indicated that emitter efficiencies of 50 percent and power densities of several watts/sq cm are attainable at moderate temperatures (less than 1750 K).

1994-08-01

471

Effect of temperature gradient on thick film selective emitter emittance  

Energy Technology Data Exchange (ETDEWEB)

A temperature gradient across a thick ({ge}.1mm) film selective emitter will produce a significant reduction in the spectral emittance from the no temperature gradient case. Thick film selective emitters of rare earth doped host materials such as yttrium-aluminum-garnet (YAG) are examples where temperature gradient effects are important. In this paper a model is developed for the spectral emittance assuming a linear temperature gradient across the film. Results of the model indicate that temperature gradients will result in reductions the order of 20{percent} or more in the spectral emittance. {copyright} {ital 1997 American Institute of Physics.}

1997-03-01

472

Effect of porosity on the superplasticity of an alumina  

Energy Technology Data Exchange (ETDEWEB)

To evaluate the effect of porosity on superplasticity behavior, it is essential to use materials of similar initial grain sizes. This can be achieved by HIPing, which provides an effective way of reducing initial porosity while avoiding appreciable grain growth; various levels of porosity can be achieved for similar grain sizes. This note is concerned with the influence of porosity on superplasticity tensile deformation of a fine grained high-purity alumina doped with copper oxide and containing a grain growth inhibitor. Specimens were prepared by slip casting to net-shape and sintering; some presintered specimens were HIPed to reduce porosity. The subsequent superplasticity behavior is related to porosity in the material.

1994-02-01

473

Direct dark matter identification with a hybrid detection technique  

CERN Document Server

In the quest to understand the ultimate nature of WIMPs, we propose the use of a hybrid detection technique: cylinders filled with liquefied noble gasses, acting as targets, are immersed inside a tank of Gd-doped ultra-pure water that provides an active and efficient veto against neutrons. The evaluation of the background rejection capabilities and physics potential of this instrument have been carried out through a full GEANT4 simulation, assuming the detector will be located at the Canfranc underground laboratory (in the Spanish Pyrenees). Our results compare very favourably with existing or planned experiments in the field. This technique is scalable and will allow to reach target masses of few tonnes in the next future.

2008-01-01

474

Combining laser chemical processing and aerosol jet printing: a laboratory scale feasibility study  

British Library Electronic Table of Contents (United Kingdom)

Abstract First results showing the viability of combining laser chemical processing (LCP) and aerosol jet printing (AJP) technologies to produce a high-efficiency front side for silicon solar cells are presented. LCP simultaneously opens the anti-reflection coating (ARC) and highly dopes the underlying silicon to create a selective emitter, while AJP is the first in a two-step fine-line contact formation procedure. The electrical properties as well as the morphology of the resulting structures are presented. Performance similar to that achieved with evaporated TiPdAg metallization is demonstrated. Copyright 2010 John Wiley & Sons, Ltd.

2011-01-01

475

Collective charge excitation of Sr_1_4_-_xCa_xCu_2_4O_4_1. A fingerprint of novel charge ordered state?  

International Nuclear Information System (INIS)

We review recent progress on experimental studies of collective charge excitations in hole-doped spin ladder system Sr_1_4_-_xCa_xCu_2_4O_4_1, focusing on anomalous features of phase excitation. We also discuss possible candidates for related charge ordered state, together with a controversial issue of the hole density transferred from spin chain layers to spin ladder layers. (author)

2007-04-01

476

Adsorption of ammonia and pyridine on copper(II)-doped magnesium-exchanged smectite clays studied by electron spin resonance  

Science.gov (United States)

The interaction between N-donor adsorbates such as ammonia and pyridine with Cu(II)-exchanged montmorillonite, beidellite, flourohectorite into smectite clays has been studied by electron spin resonance. Cu(II) cations exchanged into smectites coordinate five ammonia or pyridine molecules in beidellite, four ammonia of pyridine molecules in hydroxyhectorite. Thus, the Cu(II) cations bound to the interior surfaces of these smectite clays constitute strong Lewis acid sites. 26 refs., 7 figs., 1 tab.

1993-01-14

477

A new type active personal dosemeter with a solid state detector  

International Nuclear Information System (INIS)

We have developed a new type personal dosemeter by using a B-10 doped silicon p-n junction detector with a polyethylene radiator and a polyethylene moderator. The purpose of this study was to develop a real time neutron dosemeter with a nearly flat response in the energy range from thermal to 15 MeV and low angular dependence to the incident neutron direction. The neutron response of the dosemeter was obtained with the Monte Carlo calculation and the monoenergetic neutron experiment in a free air field and also under a condition attached on a phantom.

1988-04-01

478

Synthesis, crystal structures and luminescence properties of the Eu3+-doped yttrium oxotellurates(IV) Y2Te4O11 and Y2Te5O13  

International Nuclear Information System (INIS)

Y2Te4O11:Eu3+ and Y2Te5O13:Eu3+ single crystals in sub-millimeter scale were synthesized from the binary oxides (Y2O3, Eu2O3 and TeO2) using CsCl as fluxing agent. Crystallographic structures of the undoped yttrium oxotellurates(IV) Y2Te4O11 and Y2Te5O13 have been determined and refined from single-crystal X-ray diffraction data. In Y2Te4O11, a layered structure is present where the reticulated sheets consisting of edge-sharing [YO8]13- polyhedra are interconnected by the oxotellurate(IV) units, whereas in Y2Te5O13 only double chains of condensed yttrium-oxygen polyhedra with coordination numbers of 7 and 8 are left, now linked in two crystallographic directions by the oxotellurate(IV) entities. The Eu3+ luminescence spectra and the decay time from different energy levels of the doped compounds were investigated and all detected emission levels were identified. Luminescence properties of the Eu3+ cations have been interpreted in consideration of the now accessible ...

2008-10-01

479

Self-aligned selective-emitter plasma-etchback and passivation process for screen-printed silicon solar cells  

Energy Technology Data Exchange (ETDEWEB)

We studied whether plasma-etching techniques can use standard screen-printed gridlines as etch masks to form self-aligned, patterned-emitter profiles on multicrystalline-silicon (mc-Si) cells from Solarex. We conducted an investigation of plasma deposition and etching processes on full-size mc-Si cells processed in commercial production lines, so that any improvements obtained would be immediately relevant to the PV industry. This investigation determined that reactive ion etching (RIE) is compatible with using standard, commercial, screen-printed gridlines as etch masks to form self-aligned, selectively doped emitter profiles. This process results in reduced gridline contact resistance when followed by plasma-enhanced chemical vapor deposition (PECVD) treatments, an undamaged emitter surface easily passivated by plasma-nitride, and a less heavily doped emitter between gridlines for reduced emitter recombination. This allows for heavier ...

1997-10-14

480

Nonstoichiometry and diffusion in ceria and ceria solid solutions  

Energy Technology Data Exchange (ETDEWEB)

Some of the results of property measurements of CeO{sub 2} and its solid solutions were reviewed. The deviation from stoichiometry of undoped and doped CeO{sub 2} was presented in several figures, which suggested that CeO{sub 2} fired at high temperatures in air might be nonstoichiometric in some degree. At low temperatures, the deviation from stoichiometry in doped CeO{sub 2} is higher than undoped CeO{sub 2}. As another interesting property, CeO{sub 2} shows high solubility to trivalent cations such as rare earth elements. A possible reason behind this high solubility was presented. The nonstoichiometric defect in undoped CeO{sub 2} and the trivalent cation in solid solution with CeO{sub 2} have to be compensated by other defects. The possible defect structures in this solid solution were reviewed and the most probable structure was chosen based on density measurement and impurity dependence of oxygen diffusion coefficient. Finally the oxygen ...

2003-07-01

481

New materials synthesis: characterization of some metal-doped antimony oxides  

Energy Technology Data Exchange (ETDEWEB)

In order to understand the chemistry of altermetal dopants in antimony oxide, the detailed structural characterization of two ..beta..-Sb/sub 2/O/sub 4/ compounds is reported, Mo-doped ..beta..-Sb/sub 2/O/sub 4/ (1.5 metal%) and V-doped ..beta..-Sb/sub 2/O/sub 4/ (5 metal%). The methods used to characterize these materials are X-ray and neutron diffraction, scanning electron microscopy, Mo K-edge extended X-ray absorption fine structure spectroscopy, and elemental analysis. The atomic position of each of these dopants in Sb/sub 2/O/sub 4/ is radically different as is the overall effect on the host structure. Molybdenum does not substitute for Sb atoms, rather the Mo atoms are found in channels of electron density formed by Sb/sup 3 +/ lone pairs. The two nearest Sb/sup 3 +/ are absent and the oxygen stoichiometry is preserved. The formula is Sb/sub 1.97/Mo/sub 0.015/O/sub 4/. Vanadium incorporates substitutionally for the Sb/sup 3 +/ atoms and ...

1986-10-01

482

Luminescence studies of Nd3+- and Yb3+-doped ?-Y(IO3)3 and ?-Y(IO3)3, transparent host matrix in the mid- and beginning of the far-infrared  

International Nuclear Information System (INIS)

?-Y(IO3)3 and ?-Y(IO3)3 are transparent until 12.8 and 13.4 ?m, respectively; thus they are interesting as a potential laser matrix in the mid- and beginning of the far-infrared. So, in order to investigate the properties of lanthanides- doped anhydrous yttrium iodate, polycrystalline samples of ?-Y1-xNdx(IO3)3 (0.01?x?0.05), ?-Y1-xNdx(IO3)3 (0.001?x?0.1), ?-Y1-xYbx(IO3)3 (0.01?x?0.33) and ?-Y1-xYbx(IO3)3 (0.01?x?0.25) were synthesized. For Nd3+ ions, fluorescent emissions from the 4F3/2 multiplet were observed at 300 K under pulsed laser excitations at 750 nm and for Yb3+, fluorescent emissions from the 2F5/2 multiplet were observed at 300 K under pulsed laser excitations at 980 nm. The decays of all these emissions were measured. They are exponential and the fluorescence lifetimes are in the range 0.093-0.193 ms for Nd3+ and 0.370-0.541 ms for Yb3+, depending on the nature of the host and the concentration of doping.

2009-03-01

483

Intrinsic magnetism in Fe doped SnO2 nanoparticles  

International Nuclear Information System (INIS)

Iron doped semiconducting nanoparticles Sn1-xFexO2 with x=0, 0.001, 0.002, 0.003, 0.004, 0.01 and 0.03 were prepared by a sol-gel method. The X-ray diffraction, Transmission Electron Microscopy measurements confirm the rutile structure with no impurity phase. The three characteristic lines of electron spin resonance (ESR) are observed in the doped samples for all compositions, which is a clear evidence for rhombic Fe3+ in rutile phase. The line width of ESR increases with increase in Fe concentration due to induced disorder. The spin-pumping effect is observed at temperatures below 250 K for the samples with x=0.01 and 0.03. However, based on the Curie-Weiss susceptibility, iron is in paramagnetic state and is subject to weak antiferromagnetic interaction. Blue shift in the optical band gap is observed with increase in the Fe content. -- Graphical abstract: The ESR spectra reveal that the nature of Fe in Sn1-xFexO2 samples is isolated rhombic ...

2011-01-01

484

Electric-field-dependent electroreflectance spectra of visible-band-gap (InAlGa)P quantum-well structures  

Science.gov (United States)

We present results from the first studies of electric-field effects on optical transitions in visible-band-gap InGaP/InAlGaP multiple-quantum-well (MQW) structures. These structures, grown at 775 [degree]C by metalorganic vapor phase epitaxy on (100) GaAs substrates misoriented 6[degree] towards P(111)[r angle][l angle]111[r angle]A, consist of nominally undoped MQWs surrounded by doped In[sub 0.49]Al[sub 0.51]P cladding layers to form [ital p]-[ital i]-[ital n] diodes. The Stark shifts of various allowed and forbidden quantum-well transitions were observed in bias-dependent electroreflectance spectra of In[sub 0.49]Ga[sub 0.51]P/In[sub 0.49](Al[sub 0.5]Ga[sub 0.5])[sub 0.51]P MQW samples with 10-nm-thick layers. We find the magnitude of these shifts to depend on the details of the Mg doping profile, confirming the importance of Mg diffusion and unintentional background doping in these materials. Our results show that ...

1994-04-04

485

Electric-field-dependent electroreflectance spectra of visible-band-gap (InAlGa)P quantum-well structures  

International Nuclear Information System (INIS)

We present results from the first studies of electric-field effects on optical transitions in visible-band-gap InGaP/InAlGaP multiple-quantum-well (MQW) structures. These structures, grown at 775 degree C by metalorganic vapor phase epitaxy on (100) GaAs substrates misoriented 6 degree towards P(111)right-angle left-angle 111 right-angle A, consist of nominally undoped MQWs surrounded by doped In_0_._4_9Al_0_._5_1P cladding layers to form p-i-n diodes. The Stark shifts of various allowed and forbidden quantum-well transitions were observed in bias-dependent electroreflectance spectra of In_0_._4_9Ga_0_._5_1P/In_0_._4_9(Al_0_._5Ga_0_._5)_0_._5_1P MQW samples with 10-nm-thick layers. We find the magnitude of these shifts to depend on the details of the Mg doping profile, confirming the importance of Mg diffusion and unintentional background doping in these materials. Our results show that (InAlGa)P materials are promising for ...

486

Effects of helium/DPA ratio, alloy composition and cold work on microstructural evolution and hardening of "5"9Ni-doped Fe-Cr-Ni alloys neutron-irradiated at 465 C  

International Nuclear Information System (INIS)

Three ternary austenitic alloys (Fe-15Cr-25Ni, Fe-15Cr-25Ni-0.04P, Fe-15Cr-45Ni in both annealed and cold worked conditions) were irradiated at 465 C to 0.15, 0.28, and 0.42 dpa at above core position in the Fast Flux Test Facility utilizing the Materials Open Test Assembly to study the separate and synergistic effects of He/dpa ratio, phosphorus addition, nickel content and cold work level on microstructural evolution and hardening. The helium/dpa ratio was varied by isotopic doping with "5"9Ni to enhance the production rate of helium. The helium production rate was evaluated to be 62 appm He/dpa in the "5"9Ni-doped specimens and 0.26 appm He/dpa in the undoped specimens. Transmission electron microscopic examinations revealed that alloy composition affected significantly the evolution of microstructure during irradiation. Phosphorus addition prevented the formation of Frank loops through the precipitation of phosphide. Nickel content ...

1994-06-20

487

Transfer of elements into mother's milk; Transfer von Elementen in die Muttermilch  

Energy Technology Data Exchange (ETDEWEB)

This research project aimed to determine the factors for the transfer of the elements silver (Ag), cerium (Ce), cobalt (Co), chrome (Cr), gallium (Ga), lanthanum (La), molybdenum (Mo), niobium (Nb), radium (Ra), ruthenium (Ru), antimony (sb), thorium (Th), titanium (Ti) and uranium (U) from food into the mother's milk. This factors will be used as a basic to check and derive activity values for the contamination of food and for radiation protection at working places of suckling women. For this purpose 19 mothers collected samples daily (2-8 weeks), using the duplicate method, of all the food they consumed as well as of their milk. After microwave-assisted digestion the element contents were analysed by mass-spectroscopy with inductive coupled plasma (ICP-MS). The results of the mothers who participate for more than 5 weeks were used to make a time lapse between the intake and transfer of the elements in the mothers milk visible. (orig.) [German] Ziel ...

2000-08-01

488

Direct Comparison of the X-Ray Emission and Absorption of Cerium Oxide  

Energy Technology Data Exchange (ETDEWEB)

Bremstrahlung Isochromat Spectroscopy (BIS). The XES spectra were collected using a Specs electron gun for the excitation and the XES 350 grating monochromator and channel plate system from Scienta as the photon detection. Spectra were collected in 'normal mode,' where the electron gun kinetic energy (KE) and the energy position of the center of the channel plate were both fixed and the energy distribution in the photon (hv) spectrum was derived from the intensities distributed across the channel plate detector in the energy dispersal direction. The polycrystalline Ce sample was oxidized by exposure to air at ambient pressures. After introduction to the ultra-high vacuum system, the oxidized sample was bombarded with Ar, to clean the topmost surface region and stabilize the surface and near surface regions. Although CeO{sub 2} would be the thermodynamically preferred composition in an oxygen rich environment, the combination of a vacuum environment and ion etching may ...

2010-11-24

489

Radiostrontium in milk and tap water  

International Nuclear Information System (INIS)

Analysis of Sr-90 in milk and tap water has been conducted in New York City since 1954. The milk sample analyzed is a monthly composite of pasteurized milk purchased daily at retail stores. The monthly Sr-90 to calcium ratios for New York City since the inception of the sampling progam in 1954 through 1981 are tabulated. Samples of New York City tap water are taken daily so that by the end of the month, approximately 100 liters have been collected. Data on Sr-90 since the inception of the program are presented. The available Cs-137 data expressed as the Cs-137 to Sr-90 ratio are given. A graphical presentation of the New York City Sr-90 data is also shown.

1982-05-01

490

Process to remove the residue of the waste gas scrubbing from firings, particularly bituminous coal power plants. Verfahren zur Beseitigung des Rueckstandes der Abgaswaesche von Feuerungen, insbesondere von Steinkohlenkraftwerken  

Energy Technology Data Exchange (ETDEWEB)

Calcium sulfate dihydrate which is co-produced in the scrubbing of waste gases from bituminous coal power plants is employed in the underground road securing after recrystallization. Beta-sulfate semi hydrate is obtained from the dihydrate by recrystallisation and it is used as such or as a stiff mixture with additives as a stowing material. Particularly fly ash from coal combustion units, washery refuses and development rocks from coal mining or slags from the metallurgical industry can be used as additives. The compressive and the bending tensile strength of the stowing material can be adjusted by the water content in case beta sulfate semihydrate is used as such.

1980-08-28

491

Pilot testing of sodium thiosulfate for oxidation/scaling inhibition in lime/limestone flue gas desulfurization systems  

Energy Technology Data Exchange (ETDEWEB)

Pilot plant tests have been conducted to evaluate sodium thiosulfate as an oxidation inhibition additive in five lime/limestone slurry flue gas desulfurization processes. It was found that the oxidation rate of absorbed sulfur dioxide (SO/sub 2/) was reduced by more than 50 percent in the presence of 100 to 200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes.

1985-01-01

492

Pilot testing of sodium thiosulfate  

Energy Technology Data Exchange (ETDEWEB)

Pilot plant tests have been conducted to evaluate sodium thiosulfate as an oxidation inhibition additive in five lime/limestone slurry flue gas desulfurization processes. It was found that the oxidation rate of absorbed sulfur dioxide (SO)/sub 2/ was reduced by more than 50 percent in the presence of 100 to 200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

1986-11-01

493

Pilot testing of sodium thiosulfate  

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

1986-01-01

494

Pilot testing of sodium thiosulfate  

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvements in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

1986-11-01

495

Phase change characteristic study of spherical PCMs in solar energy storage  

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the phase change behavior of 65 mol% capric acid and 35 mol% lauric acid, calcium chloride hexahydrate, n-octadecane, n-hexadecane, and n-eicosane inside spherical enclosures to identify a suitable heat storage material. Analytical models are developed for solidification and melting of sphere with conduction, natural convection, and heat generation. Both the models are validated with previous experimental studies. Good agreement was found between the analytical predictions and experimental study and the deviations were lesser than 20%. Heat flux release at the wall, cumulative energy release to the external fluid, are revealed for the best PCM. The influence of the size of encapsulation, initial temperature of the PCM, the external fluid temperature on solidified and molten mass fraction, and the total phase change time are also investigated. (author)

2009-08-15

496

Nomographs for the rapid prediction of salt quality and influent water quality impacts on hardness leakage in steamflood water  

Energy Technology Data Exchange (ETDEWEB)

Counter-current regeneration of 2-stage sodium zeolite softeners has been employed in reducing hardness leakage level of steamflooding water to less than 1 ppm when raw water contains as much as 5,000 ppm of the total dissolved solids. Hardness leakage is caused by sodium displacement of calcium and magnesium from the bottom of the exchanger bed. This study presents nomographs providing for rapid calculations to be made, for which a convenient operational mode does not already exist. The nomographs relate the hardness leakage as a function of salt quality and influent water quality and present solutions for predicting the leakage level, salt quality requirement or the treatability of raw water required for steamflooding projects.

1982-08-01

497

Isotopes and groundwater management strategies under semi-arid area: Case of the Souss upstream basin (Morocco)  

International Nuclear Information System (INIS)

This study concerns the Souss upstream basin. The objective is to investigate the characteristics of surface water and groundwater, to assess the impact of artificial recharge as reinforcement of the natural replenishment and assess the renewal of groundwater under semi-arid area. Two major water types are observed: (i) surface waters and upstream springs (least mineralized) and (ii) all groundwater samples (prevailing calcium and magnesium bicarbonate water type). Water isotopes show a low evaporation of precipitations during infiltration. Impoverishment in heavy isotopes is the characteristic of mountain rainfalls, or of a climate colder and wetter than present. Carbon-14 activities (34-94 pmc) indicate a long residence time. The artificial recharge is low compared to the reservoir volume, due to which the renewal rate is also low.

2011-07-01

498

Inhibition of barium sulfate deposition by polycarboxylates of various molecular structures  

Energy Technology Data Exchange (ETDEWEB)

To establish a relationship between the molecular structure of polycarboxylates and their growth-retarding influence on barium sulfate, seeded-suspension-growth experiments were performed at various inhibitor concentrations and pH values. Two types of polycarboxylates with a molecular structure based on their polyacrylic or maleic acid were studied. The molecular structure of these compounds were varied by particle substitution with monomers containing hydroxyl, amide, and sulfonic acid, as well as hydrophobic groups. Hydrophobic groups are detrimental to good inhibitor performance, whereas the introduction of OH, NH {sub 2}, or SO {sub 3} H groups presents opportunities to enhance the inhibitor effectiveness. The sequence in performance of the compounds on barium sulfate was compared with the sequence formerly obtained for calcium sulfate dihydrate.

1990-02-01

499

Biomechanical properties of the femoral neck relative to osteosynthesis methods and bone mineral content assessed by computed tomography  

International Nuclear Information System (INIS)

Bone mineral content as determined by computerized tomography (CT) and mechanical strength on axial loading were compared in 36 cadaveric femur specimens. Based on the CT measurements of density and area, the mass of a transverse slice of the femur was estimated. Highly significant correlations were demonstrated between strength and cancellous bone density. Even higher correlations were revealed when the bone masses of the proximal and distal femoral areas were calculated. Based on these findings, an equal distribution of the effective mass of the femur was postulated. This hypothesis was confirmed in an experimental rotational model. The CT attenuation values were also correlated to direct measurements of bone mineral content, i.e. calcium. Moreover, the strength of different metal implants, commonly used in femoral neck fractures, were assessed in cadaver specimens. 134 refs., 13 figs., 12 tabs.