Thermal- and radiation-induced interactions of water on U02 surfaces.
Energy Technology Data Exchange (ETDEWEB)
Most plans for the disposition of surplus nuclear materials involve storage in sealed containers where the evolution of gases from reactions of adsorbed water could present both pressure and flammability hazards[l] . Despite efforts such as calcining the material to minimize the water content prior to packaging, both residual moisture and readsorbed water may be present in the final containers . Given the anticipated temperature excursions during transportation and storage, this water may thermally desorb, increasing the pressure, and/or thermally dissociate to produce H2 gas, increasing flammability hazards . In addition, the radiation from the nuclear material may induce radiolysis of the water with the likely products being water vapor, H2, 02 and H2O2. In order to better understand the relative importance of the thermal- and radiationinduced chemistry, we have studied the interactions of water on single crystals of uranium dioxide .
2003-01-01
British Library Electronic Table of Contents (United Kingdom)
This study assessed the impact of the results of genetic testing for hereditary cancer from a multifactorial health psychology perspective, considering that emotional expression plays a key role in psychological adjustment. Measures of dispositional and transactional coping strategies, anxiety and alexithymia were filled out by 77 participants in a longitudinal study design. Statistical analyses were performed using general linear models and partial least squares path modelling, low-constraint methods that are particularly useful in the behavioural sciences. While anxiety levels prior to the result announcement were predictive of the distress experienced by noncarriers, considerable variability was observed for mutation carriers. Some subjects who had lower anxiety levels before the test d...
2011-01-01
Dissolution Kinetics of Zirconia Calcine
International Nuclear Information System (INIS)
Liquid radioactive raffinates from nuclear fuel reprocessing at the Idaho National Engineering and Environmental Laboratory were solidified, or calcines, in a fluidized bed reactor at approximately 500 C to form a dry granular material. This calcine has been provisionally stored near-surface in concrete-encased stainless steel bins at the Idaho Nuclear Technology Engineering Center. Research addressing the permanent immobilization of radioactive waste has been ongoing. One option is to separate the radioactive constituents from the calcine, thereby reducing the radioactive waste volume to be ultimately stored at a national nuclear waste repository. Nitric acid dissolution of the calcine is a key front-end unit operation in the separations option. In order to design calcine dissolution equipment, quantification of dissolution reaction rate parameters is required. A ...
FMDP Reactor Alternative Summary Report: Volume 2 - CANDU heavy water reactor alternative
Energy Technology Data Exchange (ETDEWEB)
The Department of Energy Office of Fissile Materials Disposition (DOE/MD) initiated a detailed analysis activity to evaluate each of ten plutonium disposition alternatives that survived an initial screening process. This document, Volume 2 of a four volume report, summarizes the results of these analyses for the CANDU reactor based plutonium disposition alternative.
1996-09-01
Computational Analysis of the SRS Phase III Salt Disposition Alternatives
Energy Technology Data Exchange (ETDEWEB)
Completion of the Phase III evaluation and comparison of salt disposition alternatives was supported with enhanced computer models and analysis for each case on the ''short list'' of four options. SPEEDUP(TM) models and special purpose models describing mass and energy balances and flow rates were developed and used to predict performance and production characteristics for each of the options. Results from the computational analysis were a key part of the input used to select a primary and an alternate salt disposition alternative.
1999-10-07
Vehicle-Dependent Disposition Kinetics of Fluoranthene in Fisher-344 Rats
UK PubMed Central (United Kingdom)
The objective of this study was to evaluate how the vehicles of choice affect the pharmacokinetics of orally administered Fluoranthene [FLA] in rats. Fluoranthene is a member of the family of...Full Text Available
2008-03-01
Energy Technology Data Exchange (ETDEWEB)
This document provides information on the supply and disposition of natural gas to a wide audience. The 1996 data are presented in a sequence that follows natural gas from it`s production to it`s end use.
1997-09-01
Feynman-Wiener path integral representation for scalar advected diffusion
Energy Technology Data Exchange (ETDEWEB)
We write a path-integral expression for the Green function of a advected scalar on a fluid flux. (author)
2000-07-01
DOE Plutonium Disposition Study: Pu consumption in ALWRs. Volume 1, Final report
Energy Technology Data Exchange (ETDEWEB)
The Department of Energy (DOE) has contracted with Asea Brown Boveri-Combustion Engineering (ABB-CE) to provide information on the capability of ABB-CE`s System 80 + Advanced Light Water Reactor (ALWR) to transform, through reactor burnup, 100 metric tonnes (MT) of weapons grade plutonium (Pu) into a form which is not readily useable in weapons. This information is being developed as part of DOE`s Plutonium Disposition Study, initiated by DOE in response to Congressional action. This document, Volume 1, presents a technical description of the various elements of the System 80 + Standard Plant Design upon which the Plutonium Disposition Study was based. The System 80 + Standard Design is fully developed and directly suited to meeting the mission objectives for plutonium disposal. The bass U0{sub 2} plant design is discussed here.
1993-05-15
NRC regualtory agenda. Semiannual report, July 1997--December 1997
Energy Technology Data Exchange (ETDEWEB)
The Regulatory Agenda is a semiannual compilation of all rules on which the NRC has recently completed action, or has proposed action, or is considering action, and of all petitions for rulemaking that the NRC has received that are pending disposition.
1998-02-01
Laser-assisted solar-cell metallization processing
Energy Technology Data Exchange (ETDEWEB)
Laser assisted solar cell metallization processing which is a one step process is examined. The potential advantages of laser disposition techniques for photovoltaic systems are: a high resolution, no photolithography, clean and contamination free, in-situ sintering, and low contact resistance.
1984-03-01
UK PubMed Central (United Kingdom)
BackgroundTrichloroethylene (TCE) is a suspected human carcinogen and a common ground-water contaminant. Chloral hydrate (CH) is the major metabolite of TCE formed in the liver by...Full Text Available
2006-08-01
Effect of calcination and physico-chemical properties of red mud
Energy Technology Data Exchange (ETDEWEB)
Physico-chemical studies were carried out on a sample of red mud collected from NALCO, Orissa, after calcination up to 1,200 C at an interval of 100 C. The observed change in properties like surface area, particle size, bulk density and mineral phases etc., can be profitably used while finding an appropriate application of this polluting waste from alumina plants.
1996-10-01
Corrosion issues in the long term storage of aluminum-clad spent nuclear fuels
International Nuclear Information System (INIS)
Approximately 8% of the spent nuclear fuel owned by the US Department of Energy is clad with aluminum alloys. The spent fuel must be either reprocessed or temporarily stored in wet or dry storage systems until a decision is made on final disposition in a repository. There are corrosion issues associated with the aluminum cladding regardless of the disposition pathway selected. This paper discusses those issues and provides data and analysis to demonstrate that control of corrosion induced degradation in aluminum clad spent fuels can be achieved through relatively simple engineering practices.
1996-03-24
A path model of factors influencing morbidity and mortality in Ontario feedlot calves.
UK PubMed Central (United Kingdom)
The principles of path analysis and causal modelling are discussed. Path analysis was applied to three data sets to assess the relationship between group characteristics (number per group and "mixing"...Full Text Available
1986-01-01
Numerical integration of the Feynman Path Integral for radiative transport
International Nuclear Information System (INIS)
The radiative transport problem is cast in integral form using a transport kernel. The transport kernel has an explicit representation in terms of a Feynman Path Integral over all paths between selected points in a volume. This representation is setup in detail. Numerical evaluation of this Path Integral is formulated with a Frenet-Serret based procedure for generating valid random paths, and with a numerical evaluation of the weight for each valid path. Very early sanity checks of a numerical implementation are reported. Approaches to optimization are identified. (authors)
2009-05-03
The Successive Approximation Approach for Multi-path Utility Maximization Problem
The network utility maximization (NUM) problem for multi-path is a problem which is non-strictly convex and non-separable. Using Jensen's inequality, we approximate the NUM to a strictly convex and separable problem which can be solved efficiently by the dual decomposition method. After a series of approximations, the result of the approximation problem converges to the globally optimal solution of the original NUM. Moreover, because of the separable and dual-based natures of the proposed algorithm, we utilize the reverse engineering frameworks of the current TCPs to develop a series of multi-path TCPs which are totally compatible with current TCPs. The multi-path users using our protocols can run simultaneously with the single-path users using the current TCPs. The simulations of our Multi-path Reno on ns-2 show the compatibility and the fairness among ...
2011-01-01
Feynman path integral representations for wave scattering by anisotropic perturbations
Energy Technology Data Exchange (ETDEWEB)
We write a space-time Feynman Path Integral representation for scattered wave fields from a weakly/compact supported anisotropic non-homogeneity. (author)
2007-07-01
JPF is an explicit state software model checker for Java bytecode. Today, JPF is a swiss army knife
2005-01-01
Pyridostigmine bromide modulates the dermal disposition of [14C]permethrin.
The cause of the Gulf War Syndrome may be related to soldiers being exposed to insecticides (e.g., permethrin (P)), insect repellents (e.g., N,N-diethyl-m-toluamide (DEET)), an organophosphate nerve agent simulant (e.g., diisopropyl fluorpohosphate (DFP)), and/or prophylactic treatment (e.g., pyridostigmine bromide (PB)) against potential nerve gas attacks. The purpose of this study was to assess the dermal disposition of [14C]permethrin in ethanol or ethanol:water (3:2) in the isolated perfused porcine skin flap (IPPSF) model with simultaneous dermal exposure to DEET or DFP. These IPPSFs were also simultaneously perfused arterially with or without PB, DFP, or DFP + PB. The results indicated that DFP + PB significantly increased [14C]permethrin absorption compared to controls (1.06% dose vs 0.14% dose). PB significantly increased [14C]permethrin disposition in the stratum corneum (SC) in aqueous mixtures only (9.40 vs 3.35% dose), while topical ...
2002-06-15
Accelerating the disposition of transuranic waste from LANL - 9495
Energy Technology Data Exchange (ETDEWEB)
Los Alamos National Laboratory (LANL) was established during World War II with a single mission -- to design and build an atomic bomb. In the 65 years since, nuclear weapons physics, design and engineering have been the Laboratory's primary and sustaining mission. Experimental and process operations -- and associated cleanout and upgrade activities -- have generated a significant inventory of transuranic (TRU) waste that is stored at LANL's Technical Area 54, Material Disposal Area G (MDA G). When the Waste Isolation Pilot Plant (WIPP) opened its doors in 1999, LANL's TRU inventory totaled about 10,200 m{sup 3}, with a plutonium 239-equivalent curie (PE Ci) content of approximately 250,000 curies. By December 2008, a total of about 2,300 m3 (61,000 PE Ci) had been shipped to WIPP from LANL. This has resulted in a net reduction of about 1,000 m{sup 3} of TRU inventory over that time frame. This paper presents progress in dispositioning ...
2009-01-01
The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.
1997-07-01
Connecting section and associated systems concept for the spray calciner/in-can melter process
Energy Technology Data Exchange (ETDEWEB)
For a number of years, researchers at the Pacific Northwest Laboratory have been developing processes and equipment for converting high-level liquid wastes to solid forms. One of these processes is the Spray Calciner/In-Can Melter system. To immobilize high-level liquid wastes, this system must be operated remotely, and the calcine must be reliably conveyed from the calciner to the melting furnace. A concept for such a remote conveyance system was developed at the Pacific Northwest Laboratory, and equipment was tested under full-scale, nonradioactive conditions. This concept and the design of demonstration equipment are described, and the results of equipment operation during experimental runs of 7 d are presented. The design includes a connecting section and its associated systems - a canister sypport and alignment concept and a weight-monitoring system for the melting furnace. Overall, the runs demonstrated that the ...
1981-06-01
Calcination of Fluorinel-sodium waste blends using sugar as a feed additive (formerly WINCO-11879)
Energy Technology Data Exchange (ETDEWEB)
Methods were studied for using sugar as a feed additive for converting the sodium-bearing wastes stored at the Idaho Chemical Processing Plant into granular, free flowing solids by fluidized-bed calcination at 500{degrees}C. All methods studied blended sodium-bearing wastes with Fluorinel wastes but differed in the types of sugar (sucrose or dextrose) that were added to the blend. The most promising sugar additive was determined to be sucrose, since it is converted more completely to inorganic carbon than is dextrose. The effect of the feed aluminum-to-alkali metal mole ratio on calcination of these blends with sugar was also investigated. Increasing the aluminum-to-alkali metal ratio from 0.6 to 1.0 decreased the calcine product-to-fines ratio from 3.0 to 1.0 and the attrition index from 80 to 15%. Further increasing the ratio to 1.25 had no effect.
1992-06-01
Production of a potassium silicate fertilizer from fly ash and red mud
Energy Technology Data Exchange (ETDEWEB)
A study is reported of the use of three types of fly ash as a raw material in the production of a potassium silicate fertilizer. The results of high-temperature X-ray diffraction, calcination tests and chemical analyses indicate that a potassium silicate fertilizer conforming with fertilizer specifications can be produced by appropriate regulation of calcining temperature and the amounts of Fe/sub 2/0/sub 3/, Al/sub 2/O/sub 3/, MgO and CaO added. The results of tests of fertilizers incorporating red mud are also reported.
1985-01-01
Computer processing of Moessbauer spectrum data
International Nuclear Information System (INIS)
Computer processing was adopted to pick up significant signals from the undefined Moessbauer spectra. A program, by which smoothing and curve fitting was made possible, was devised and applied to the analysis of the Moessbauer spectra of "5"7Fe enriched iron and other specimens. Although this processing sometimes distorted the absorption peaks, it was quite effective for elimination of noise and finding of exact positions of absorption peaks. Availability of the processing was demonstrated by several examples obtained for "5"7Fe enriched iron, natural iron, calcined ferric oxyhydroxides, red mud residue and its calcined product. (auth.).
Energy Technology Data Exchange (ETDEWEB)
With the end of the cold war the United States, Russia, and other countries have excess plutonium and other materials from the reductions in inventories of nuclear weapons. The United States Academy of Sciences (NAS) has recommended that these surplus fissile materials (SFMs) be processed so they are no more accessible than plutonium in spent nuclear fuel (SNF). This spent fuel standard, if adopted worldwide, would prevent rapid recovery of SFMs for the manufacture of nuclear weapons. The NAS recommended investigation of three sets of options for disposition of SFMs while meeting the spent fuel standard: (1) incorporate SFMs with highly radioactive materials and dispose of as waste, (2) partly burn the SFMs in reactors with conversion of the SFMs to SNF for disposal, and (3) dispose of the SFMs in deep boreholes. The US Government is investigating these options for SFM disposition. A new method for the disposition of SFMs ...
1995-01-31
UK PubMed Central (United Kingdom)
Path analysis was used to determine the interrelationships between postpartum administration of gonadotrophin releasing hormone and cloprostenol and the occurrence of reproductive disease and reproductive...Full Text Available
1985-07-01
UK PubMed Central (United Kingdom)
Path analysis was used to determine the interrelationships between ambient temperature, age at calving, postpartum reproductive events and reproductive performance in dairy cows. The data used in the...Full Text Available
1985-07-01
Interim Safety Basis for Fuel Supply Shutdown Facility
Energy Technology Data Exchange (ETDEWEB)
This ISB, in conjunction with the IOSR, provides the required basis for interim operation or restrictions on interim operations and administrative controls for the facility until a SAR is prepared in accordance with the new requirements or the facility is shut down. It is concluded that the risks associated with tha current and anticipated mode of the facility, uranium disposition, clean up, and transition activities required for permanent closure, are within risk guidelines.
2000-09-07
Estimating demolition cost of plutonium buildings for dummies
Energy Technology Data Exchange (ETDEWEB)
The primary purpose of the Rocky Flats Field Office of the US Department of Energy is to decommission the entire plant. In an effort to improve the basis and the accuracy of the future decommissioning cost, Rocky Flats has developed a powerful but easy-to-use tool to determine budget cost estimates to characterize, decontaminate, and demolish all its buildings. The parametric cost-estimating tool is called the Facilities Disposition Cost Model (FDCM).
2000-07-01
Early disposition of inhaled uranyl nitrate ("2"3"2U and "2"3"3U) in rats
International Nuclear Information System (INIS)
Uranyl nitrate ("2"3"3U) was retained mainly in lung, skeleton, pelt and kidney 60 days after inhalation exposure. The concentration in lung exceeded that in other tissues. Preliminary results with "2"3"2U indicate retention in lung similar to that of "2"3"3U, at total deposited mass levels of 0.1 #mu#g or less.
1977-05-01
Disposition of "8"5Kr in gravid rats
International Nuclear Information System (INIS)
Pregnant rats were exposed to "8"5Kr for 4-6 hr and sacrificed immediately thereafter. The "8"5Kr concentration in the fetoplacental unit (FPU) was approximately the same at all gestation stages for intact FPU, isolated fetuses or fetal segments, as well as placentas and associated membranes. Maternal tissue concentrations varied over a wide range and only liver and intestine concentrations were relatively similar in both 20-day-gestation (dg) fetuses and adults.
1977-05-01
Energy Technology Data Exchange (ETDEWEB)
This report summarizes activities of the Amarillo National Resource Center for Plutonium during the quarter. The report describes the Electronic Resource Library; DOE support activities; current and future environmental health and safety programs; pollution prevention and pollution avoidance; communication, education, training, and community involvement programs; and nuclear and other material studies, including plutonium storage and disposition studies.
1997-12-31
Model Checking Real Time Java Using Java PathFinder
The Real Time Specification for Java (RTSJ) is an augmentation of Java for real time applications of
2005-01-01
Broadcast Analysis for Large Cooperative Wireless Networks
The capability of nodes to broadcast their message to the entire wireless network when nodes employ cooperation is considered. We employ an asymptotic analysis using an extended random network setting and show that the broadcast performance strongly depends on the path loss exponent of the medium. In particular, as the size of the random network grows, the probability of broadcast in a one-dimensional network goes to zero for path loss exponents larger than one, and goes to a nonzero value for path loss exponents less than one. In two-dimensional networks, the same behavior is observed for path loss exponents above and below two, respectively.
2011-01-01
British Library Electronic Table of Contents (United Kingdom)
Sulfated zirconia (SO4-ZrO2) catalysts, prepared with three different sulfur loading contents (0.75%, 1.8% and 2.5%) at two calcination temperatures (500degreeC and 700degreeC), were tested for use in the transesterification of purified palm oil (PPO) and the esterification of palm fatty acid (PFA) in near-critical and super-critical methanol. Techniques including BET, XRD, NH3- and CO2-TPD revealed that the sulfur content and calcination temperature strongly affects the catalyst base-acid site, specific surface area, average pore size, phase structure, and thus the catalytic reactivity. The most suitable sulfur loading content was found to be 1.8% and the optimum calcination temperature 500degreeC. The results show that the use of SO4-ZrO2 reduces esterification reaction times, the amount...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
This lectures aim at giving graduate students an introduction to a working knowledge of path integral methods in a wide variety of fields in physics. Consequently, the the lecture notes are organized in three main parts dealing with non-relativistic quantum mechanics, many-body physics and field theory. In the first part the basic concepts of path integrals are developed in the usual heuristic, non-mathematical way followed by the standard examples of quadratic Lagrangians for which the path integrals can be solved exactly. Applications include semi-classical expansions, scattering problems and the representation of Green functions as path integrals. In the last chapter of this part it is shown how (euclidean) path integrals can be treated numerically by Monte-Carlo methods with a program for the anharmonic oscillator as an explicit example. The second part deals with the ...
1997-12-01
International Nuclear Information System (INIS)
A path integral evaluation of the Green's function for the hydrogen atom initiated by Duru and Kleinert is studied by recognizing it as a special case of the general treatment of the separable Hamiltonian of Liouville type. The basic dynamical principle involved is identified as Jacobi's principle of least action for given energy which is reparametrization invariant, and thus the appearance of a gauge freedom is naturally understood. The separation of variables in the operator formalism corresponds to a choice of gauge in the path integral, and the Green's function is shown to be gauge independent if the operator ordering is properly taken into account. Unlike the conventional Feynman path integral, which deals with a space-time picture of particle motion, the path integral on the basis of Jacobi's principle sums over orbits in space. We illustrate these properties by evaluating an exact ...
Acousto-optic multiplexing and demultiplexing
Energy Technology Data Exchange (ETDEWEB)
A system is claimed for multiplexing or demultiplexing pulsed laser radiation having an acousto-optical device which is electrically controlled to switch a common path of high pulse rate laser radiation between a plurality of spatially distinct paths for relatively lower pulse rate laser radiation at which the pulses are sequenced according to a predetermined time pattern. The acousto-optical element typically includes a Bragg cell which is electrically driven by a set of distinct frequencies, causing deflection of radiation passing therethrough at a predetermined set of angles whereby pulsed radiation on a single path may be distributed onto the plural separate paths or radiation on plural separate paths of time-sequenced pulses of radiation can be combined into a single path of augmented pulse rate. The control of the acousto-optical element may be provided by ...
1980-06-03
Quantitative determination of Broensted acid site concentrations in calcined H-mordenite and H-ZSM-5 by means of conductometric titration and infrared spectroscopy reveals that the concentration of Broensted acid sites present is lower than would be expected on the basis of the aluminum content. This discrepancy is attributed to dealumination and dehydroxylation processes occurring during calcination. A model is proposed according to which the degree of these processes strongly depends on the concentration of vicinal aluminum T sites in the zeolite: Broensted acid sites associated with these T sites are lost, and the remaining Broensted acidity is related to the concentration of the (remaining) isolated aluminum T sites. This model quantitatively correlates the experimentally determined concentration of Broensted acid sites with the concentration of isolated aluminum T sites. 33 refs., 4 figs., 2 tabs.
1993-01-14
Particulate composites in the TiC-TiYTZP system
International Nuclear Information System (INIS)
Twelve powders of TiO_2-Y_2O_3-ZrO_2 solid solution of the methodically changed composition were prepared by a coprecipitation-calcination technique. After mixing with phenol-formaldehyde resin, the powders were calcinated for 2 hours at 1200"oC in vacuum. The resultant composite powders contained TiC and non-reacted carbon. Green compacts were sintered in vacuum at 1500"oC for 2 hours. A temperature increase was stopped at 1200"oC to react remains of carbon. There were two carbides in the composites TiC and ZrC. TiC non-stoichiometry depended on carbon content in the system. Phase composition of the depended on of titania and yttria in zirconia solid solution. The majority of the samples showed two tetragonal zirconia phases differing in lattice parameter and tetragonality. (author)
2004-09-12
Moessbauer spectroscopic determination of chemical state of iron in bauxite
International Nuclear Information System (INIS)
The chemical state of iron contained in several kinds of bauxite, which are utilized as a raw material in the aluminum industry in Japan, were investigated by Moessbauer spectroscopy. The main compounds of iron were identified from the results, which showed variations of the Moessbauer absorption spectra with calcination and measuring temperature. Although the absorption intensities of the spectra differed significantly, major species identified were paramagnetic or superparamagnetic #alpha#-Fe_2O_3 in all of these bauxite samples. The superparamagnetic #alpha#-Fe_2O_3 was found mainly in the gibbsite-type bauxite, but not in the boehmite/gibbsite-type or the boehmite-type bauxite. The Moessbauer absorption spectra of red mud and its calcined products were also given. (author).
Development of a pozzolanic pigment from red mud
Energy Technology Data Exchange (ETDEWEB)
Red mud is a waste generated by the aluminum industry, and its disposal is a major problem for this industry. Very rich in iron, it can be used as cheap pigment for colored concrete. The red coloration can be enhanced by calcination in the range of 600 to 800 C. Such operation also transforms the aluminum hydroxides (goethite and boehmite) and clays minerals into pozzolanic admixtures that are able to consume the calcium hydroxide produced by cement hydration. Thus, it is possible to develop a new admixture for concrete: a pozzolanic pigment. The pozzolanic properties of calcined red mud were investigated by monitoring lime consumption of different mixtures of OPC and red mud. The main products of hydration were C-S-H and mono-carboaluminate (C{sub 4}A{bar C}H{sub 11}). A uniform and durable colored concrete was obtained using white cement interground with 11% of burnt red mud.
1997-10-01
Energy Technology Data Exchange (ETDEWEB)
This report describes the physical characteristics of a ceramic-lined, joule-heated glass melter that is directly connected to the discharge of a spray calciner and is currently being used to study the vitrification of simulated nuclear-waste slurries. Melter performance characteristics and subsequent design improvements are described. The melter contains 0.24 m/sup 3/ of glass with a glass surface area of 0.76 m/sup 2/, and is heated by the flow of an alternating current (ranging from 600 to 1200 amps) between two Inconel-690 slab-type electrodes immersed in the glass at either end of the melter tank. The melter was maintained at operating temperature (900 to 1260/sup 0/C) for 15 months, and produced 62,000 kg of glass. The maximum sustained operating period was 122 h, during which glass was produced at the rate of 70 kg/h.
1980-11-01
Catalyst and method for reduction of nitrogen oxides
Energy Technology Data Exchange (ETDEWEB)
A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).
2008-08-19
Catalyst and method for reduction of nitrogen oxides
Energy Technology Data Exchange (ETDEWEB)
A Selective Catalytic Reduction (SCR) catalyst was prepared by slurry coating ZSM-5 zeolite onto a cordierite monolith, then subliming an iron salt onto the zeolite, calcining the monolith, and then dipping the monolith either into an aqueous solution of manganese nitrate and cerium nitrate and then calcining, or by similar treatment with separate solutions of manganese nitrate and cerium nitrate. The supported catalyst containing iron, manganese, and cerium showed 80 percent conversion at 113 degrees Celsius of a feed gas containing nitrogen oxides having 4 parts NO to one part NO.sub.2, about one equivalent ammonia, and excess oxygen; conversion improved to 94 percent at 147 degrees Celsius. N.sub.2O was not detected (detection limit: 0.6 percent N.sub.2O).
2008-05-27
Energy Technology Data Exchange (ETDEWEB)
This report describes the 5 tasks to be covered under this project and compiles budget information. Task 1 is to establish a Plutonium Information Resource, which has been established in Amarillo, Texas. Task 2, Advisory Functions, coordinates studies and activities relating to the disposition of excess weapons-grade plutonium. Task 3, Environmental, Public Health, and Safety, supports soil remediation activities. Task 4, Education and Outreach, is supporting four programs: K--12 education improvement in science and math courses; Academic intervention to identify and encourage high ability high school and middle school students with potential to become scientists and engineers; Graduate education evaluation; and Public outreach programs. Task 5, Plutonium and other Materials Studies, is currently funding two projects for the disposition of high explosives: a feasibility study of burning a mixture of high explosives and other materials in a ...
1995-06-29
The influence of compound admixtures on the properties of high-content slag cement
Energy Technology Data Exchange (ETDEWEB)
Based on the activation theory of alkali and sulfate, the influence of compound admixtures on the properties of high-content slag cement was studied by testing the strength, pore structure, hydrates, and microstructure, Test results show that compound admixtures can obviously improve the properties of high-content slag cement. The emphasis of the present research is two-fold: substituting gypsum with anhydrite and calcining gypsum. These both can improve early and later performance.
2000-01-01
Phosphorus-containing catalyst and catalytic cracking process utilizing the same
Energy Technology Data Exchange (ETDEWEB)
A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with a dihydrogen phosphate anion or a dihydrogen phosphite anion. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.
1985-02-12
Phosphorus-containing catalyst and catalytic cracking process utilizing the same
Energy Technology Data Exchange (ETDEWEB)
A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with an anion such as a dihydrogen phosphate anion or a dihydrogen phosphite anion and additionally with an ammonium salt other than a salt of an inorganic acid of phosphorus. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.
1985-03-12
Energy Technology Data Exchange (ETDEWEB)
The production of hydrogen from the two-stage pyrolysis-gasification of polypropylene using a Ni/CeO{sub 2}/ZSM-5 catalyst has been investigated. Experiments were conducted on CeO{sub 2} loading, calcination temperature and Ni loading of the Ni/CeO{sub 2}/ZSM-5 catalyst in relation to hydrogen production. The results indicated that with increasing CeO{sub 2} loading from 5 to 30 wt.% for the 10 wt.% Ni/CeO{sub 2}/ZSM-5 catalyst calcined at 750 C, hydrogen concentration in the gas product and the theoretical potential hydrogen production were decreased from 63.0 to 49.8 vol.% and 50.4 to 21.6 wt.%, respectively. In addition, the amount of coke deposited on the catalyst was reduced from 9.5 to 6.2 wt.%. The calcination temperature had little influence on hydrogen production for the catalyst containing 5 wt.% of CeO{sub 2}. However, for the 10 wt.% Ni/CeO{sub 2}/ZSM-5 catalyst with a CeO{sub 2} content of 10 or 30 wt.%, the ...
2009-08-15
Investigation of corrosion experienced in a spray calciner/ceramic melter vitrification system
Energy Technology Data Exchange (ETDEWEB)
After periodic testing of a large-scale spray calciner/ceramic melter vitrification system over a 2-yr period, sufficient corrosion was noted on various parts of the vitrification system to warrant its disassembly and inspection. A majority of the 316 SS sintered metal filters on the spray calciner were damaged by chemical corrosion and/or high temperature oxidation. Inconel-601 portions of the melter lid were attacked by chlorides and sulfates which volatilized from the molten glass. The refractory blocks, making up the walls of the melter, were attacked by the waste glass. This attack was occurring when operating temperatures were >1200/sup 0/C. The melter floor was protected by a sludge layer and showed no corrosion. Corrosion to the Inconel-690 electrodes was minimal, and no corrosion was noted in the offgas treatment system downstream of the sintered metal filters. It is believed that most of the melter corrosion occurred during one ...
1980-08-01
Desulphurization of hot reducing gases in the entrained bed reactor
Energy Technology Data Exchange (ETDEWEB)
Using an experimental pilot plant, designed and built for the tests, the influence of the following parameters was determined: desulphurization of the test gas, temperature, residence time in the reactor tube, concentration of the hydrogen sulphide and desulphurization agent, size of the particles which comprise the agent and composition of the gas. Allowance was made for the effect of calcination and carbonisation. Desulphurization was carried out with limestone on a gaseous mixture of CO and H/sub 2/. A mathematical description of the test findings and yield is presented. 8 refs.
1986-08-01
Catalysis over activated zeolites
A process is provided for conducting organic compound conversion over a catalyst composition comprising a supported crystalline zeolite having a high initial silica-to-alumina mole ratio, said supported zeolite being prepared by compositing said crystalline zeolite with alumina, reacting the composite with a particular hydrogen fluoride solution in a specified way, drying the hydrogen fluoride reacted composite, treating the dried composite by hydrolysis, ammonolysis and/or by contact with an ammonium salt solution, and calcining the resulting material.
1985-02-19
International Nuclear Information System (INIS)
A non-linear mathematical model of dynamics of horizontal steam generator for nuclear power unit with WWER type reactor is presented. To realize this model the GEMMA-120 simulation language for computer Odra-1204 has been used. Necessity of taking into account disposited thermal storage capacities along tubulation of a primary cycle is demonstrated. A number of lumped elements of reactor division against a required static accuracy of calculations has been determined. (author).
1977-01-01
Lithium isotopes: differential effects in animals
Energy Technology Data Exchange (ETDEWEB)
Differences in the biological disposition and in the effects of the stable lithium isotopes, Li-6 and Li-7, in animals were characterized. A somewhat higher toxicity was associated with WLiCl compared to XLiCl with NLiCl intermediate. All lithium treatments increased water intake and resulted in weight gain. Peak plasma concentration was slightly high for 6Li than 7LiCl suppressed action potential amplitudes during tetanic stimulation more than NaCl when added to Renger solution bathing ganglia.
1984-04-01
ICDF Complex Operations Waste Management Plan
This Waste Management Plan functions as a management and planning tool for managing waste streams generated as a result of operations at the Idaho CERCLA Disposal Facility (ICDF) Complex. The waste management activities described in this plan support the selected remedy presented in the Waste Area Group 3, Operable Unit 3-13 Final Record of Decision for the operation of the Idaho CERCLA Disposal Facility Complex. This plan identifies the types of waste that are anticipated during operations at the Idaho CERCLA Disposal Facility Complex. In addition, this plan presents management strategies and disposition for these anticipated waste streams.
2006-12-01
International Nuclear Information System (INIS)
In the heat exchangers of power plants, scale deposition may occur, especially at the leading edge of contraction. The growth of scale can lead to an increase in pressure and cause oscillation of the water level. In our previous study, the dependence of flow on contraction geometry was analyzed numerically and empirically. It was shown that the contraction ratio of hydraulic diameter of the flow path contributed greatly to the difference in pressure drop and turbulent kinetic energy at the leading edge of the flow path. In this study, the effect of contraction geometry and flow rate on scale adhesion was studied in AVT chemistry at 270degC using a high-velocity scale-adhesion test loop. The differential pressure and the amount of scale deposited due to scale adhesion at the leading edge of the flow path increased more in a quatrefoil-type flow path than in drill-type flow path. The ...
1999-05-01
Solar thermal production of zinc: Program strategy
Energy Technology Data Exchange (ETDEWEB)
The solar thermal production of zinc is considered for the conversion of solar energy into storable and transportable chemical fuels. The ultimate objective is to develop a technically and economically viable technology that can produce solar zinc. The program strategy for achieving such a goal involves research on two paths: a direct path via the solar thermal splitting of ZnO in the absence of fossil fuels, and an indirect path via the solar carbothermal/CH{sub 4}-thermal reduction of Zn O, with fossil fuels (coke or natural gas) as chemical reducing agents. Both paths make use of concentrated solar energy for high-temperature process heat. The direct path brings us to the complete substitution of fossil fuels with solar fuels for a sustainable energy supply system. The indirect path creates a link between today`s fossil-fuel-based technology and tomorrow`s ...
1999-08-01
Open test assembly (OTA) shear demonstration testing work/test plan
Energy Technology Data Exchange (ETDEWEB)
This document describes the development testing phase associated with the OTA Shear activity and defines the controls to be in place throughout the testing. The purpose of the OTA Shear Program was to provide equipment that is needed for the processing of 40 foot long, sodium wetted, irradiated core components previously used in the FFTF reactor to monitor fuel and materials tests. There are currently 15 of these OTA test stalks located in the Test Assembly Conditioning Station (TACS) inerted vault. These need to be dispositioned for a shutdown mission to eliminate this highly activated, high dose inventory prior to turnover to the ERC since they must be handled by remote operations. These would also need to be dispositioned for a restart mission to free up the vault they currently reside in. The waste handling and cleaning equipment in the J33M Cell was designed and built for the handling of reactor components up to the standard 12 foot ...
1998-07-16
Gravitational Waves and the Sagnac Effect
We consider light waves propagating clockwise and other light waves propagating counterclockwise around a closed path in a plane (theoretically with the help of stationary mirrors). The time difference between the two light propagating path orientations constitutes the Sagnac effect. The general relativistic expression for the Sagnac effect is discussed. It is shown that a gravitational wave incident to the light beams at an arbitrary angle will not induce a Sagnac effect so long as the wave length of the weak gravitational wave is long on the length scale of the closed light beam paths. The gravitational wave induced Sagnac effect is thereby null.
2003-01-01
International Nuclear Information System (INIS)
Portuguese 1984. p. 146. Brazil Czepielewski, MA Kater, CE Biglieri, EG Escola
1984-10-27
Range-resolved gas concentration measurements using tunable semiconductor lasers
British Library Electronic Table of Contents (United Kingdom)
A method for range-resolved gas sensing using path-integrated optical systems is presented. The method involves dividing an absorption path into several measurement segments and extracting the gas concentration in each segment from two path-integrated measurements. We implemented the method with tunable lasers (a 1389-nm VCSEL and a 10.9-?m pulsed quantum cascade laser) and a group of retro reflectors (RRs) distributed along absorption paths. Using a rotating mirror with the VCSEL configuration, we could scan a group of seven tape RRs spaced by 10?cm in ??9?ms to extract an H2O concentration profile. Reduced H2O concentrations were recorded in the segments purged with dry air. Hollow corner cube RRs were used in the quantum cascade laser configuration at distances up to 1.1?km from the las...
2008-01-01
Limiting factors and landscape connectivity: the American marten in the Rocky Mountains
British Library Electronic Table of Contents (United Kingdom)
In mobile animals, movement behavior can maximize fitness by optimizing access to critical resources and minimizing risk of predation. We sought to evaluate several hypotheses regarding the effects of landscape structure on American marten foraging path selection in a landscape experiencing forest perforation by patchcut logging. We hypothesized that in the uncut pre-treatment landscape marten would choose foraging paths to maximize access to cover types that support the highest density of prey. In contrast, in the post-treatment landscapes we hypothesized marten would choose paths primarily to avoid crossing openings, and that this would limit their ability to optimally select paths to maximize foraging success. Our limiting factor analysis shows that different resistant models may be sup...
2011-01-01
Checks are performed on the alignment of the magnets in the LHC tunnel. It is vital that each magnet is placed exactly where it has been designed so that the path of the beam is precisely controlled.
2007-01-01
Effect of Stress and Strain Path on Cavity Closure During Hot ...
... CLOSURE DURING HOT WORKING OF AN ALPHA/BETA TITANIUM ALLOY (PREPRINT) ... HOT WORKING OF AN ALPHA/BETA TITANIUM ALLOY ...
2007-07-01
International Nuclear Information System (INIS)
The second-order spatial subwavelength interference pattern is observed in a modified Michelson interferometer with single-mode continuous-wave laser beams. By analyzing our subwavelength interference experiment based on Feynman's path integral theory, a unified interpretation for all the second-order subwavelength interference is suggested.
2010-07-01
Learning Online Social Support: An Investigation of Network Information Technology Based on UTAUT
British Library Electronic Table of Contents (United Kingdom)
ABSTRACT Extending the unified theory of acceptance and use of technology (UTAUT) model, this study postulates a model of online social support. The model is empirically tested using data from undergraduates in Taiwan regarding their usage of instant messaging (IM). The test results indicate that all model paths are significant, except that the path between online social support and facilitating conditions is insignificant. This study offers limitations and implications.
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
The important amount of hydration water in the ulexite (NaCaN{sub 5}O{sub 9}.8H{sub 2}O), allows using calcination methods to increase its B{sub 2}O{sub 3} content. This paper analyses the thermal decomposition reaction of a preconcentrated ulexite through weight loss measurements, which occur during the heating of samples until 1000 degree centigree, Determinations of heat content at each temperature were made using an isoperibol calorimeter. The mean specific heat was calculated from these values, and its dependence on temperature was determined. The maximum weight loss was about 32.5% and the specific heat obtained was 1,13 kJ/kg 0 C for solid samples and 1,38 kJ/kg''0 C for fluid samples. The results are useful for the design of the industrial process, in order to determine the thermal requirements for heating calcined ulexite, and to obtain smelted ulexite. (Author) 19 refs.
2006-07-01
Synthesis of yttrium iron garnet powder by homogeneous precipitation and its crystallization
Energy Technology Data Exchange (ETDEWEB)
YIG precursor powder was obtained by homogeneous precipitation in chloride salt solution by thermal decomposition of urea. It was found that ferric ions precipitated prior to yttrium ions. The precipitate was minute and spherical in shape. The precipitate formed consisted of the mixture of amorphous and ferric oxyhydroxide. Crystallization of YIG was proceeded by solid state reaction of intermediate YFeO{sub 3} and Fe{sub 2}O{sub 3} in the temperature range of 850 deg. C to 1400 deg. C. Single phase of YIG was obtained by heat-treatment of the powder at 1400 deg. C for 6 hrs in air. The powder calcined was molded into pellets and sintered in air. The maximum density of 4.92 g/cm{sup 3} (95.1% of theoretical density) was obtainable for the pellet sintered at 1450 deg. C using the powder calcined at 900 deg. C. (author) 20 refs., 8 figs., 1 tab.
1996-06-01
British Library Electronic Table of Contents (United Kingdom)
In this work, bismuth sodium titanate (Bi0.5Na0.5)TiO3 (BNT) and praseodymium (Pr)-doped BNT were successfully produced using the soft combustion technique. The effects of Pr doping on stoichiometry, microstructure, density and dielectric properties were studied. Pure Pr-doped BNT was obtained in all samples containing 5, 10 and 20mol% Pr after calcination at 800^oC for 3h. The produced powders were then pressed into pellets and sintered at 1100^oC for 3h. The very similar ionic radii of Pr^3^+ with Bi^3^+ and Na^+ made it possible to substitute both Bi and Na. The crystallite size and grain size decreased with increasing Pr amount because Pr acted as grain growth inhibitor, both for calcined powders and for sintered pellets. Maximum density was obtained in 5mol% Pr-doped BNT, beyond which...
2011-01-01
Volume reduction: a short-term answer to the mounting radwaste problem
International Nuclear Information System (INIS)
Various volume-reduction methods are discussed and their capabilities evaluated. The following volume-reduction methods have the greatest potential at this time: forced-circulation evaporator/crystallizer; incinerator (conventional type); compactor; fluidized-bed calciner/incinerator; fluidized-bed dryer/incinerator; thin-film evaporator; extruder/evaporator; drum mixer; ribbon blender; inert-carrier evaporative process; molten-glass incinerator. The first eight system types listed above have been improved to the point of commercial viability.
1980-01-01
Energy Technology Data Exchange (ETDEWEB)
Application to carbon fiber started in this Year. In this paper, a spinning and calcination process are explained. Fiber was obtained by wet spinning of the PAN solution. Ten solvents were tested and the results proved that dimethyl sulfoxide (DMSO) was the best solvent. Glycerine was used as a coagulating bath. The thin fiber (10 to 50 denier) was produced under the conditions of about 20wt% concentration at about 110degC. Heat-treat temperature was about 270 to 275degC. The viscosity-tacticity relationship and T{sub sol} vs. inverse tacticity were shown in the paper. (S.Y.)
1998-01-01
International Nuclear Information System (INIS)
Lithium orthosilicate (Li_4SiO_4) powder was synthesized by the solid-state reaction of lithium oxide with amorphous silica, and the effects of fabrication parameters on the structural characteristics of the product were investigated. Processing considerations such as milling media, drying technique, calcination time and temperature, pressing behavior, sintering time and temperatures, and impurity concentration were addressed. The initial powder particle size was observed to be important in achieving high sintered density, with densities as high as 98% TD achieved with a particle size of approximately 1 #mu#m. 9 refs., 6 figs.
1988-04-10
Production of blast furnace coke via novel briquetting system
A method of making high strength coke briquettes suitable for use as blast furnace coke comprising, (A) providing coal, (B) heating the coal at a temperature at or above the softening point of the coal to form partially carbonized char, (C) cooling the partially carbonized char below the softening point of the coal, (D) mixing the cooled partially carbonized char and tar to form a mixture of tar and partially carbonized char, (E) briquetting the mixture of tar and partially carbonized char to form briquettes of tar and partially carbonized char, (F) calcinating the briquettes to form high strength briquettes.
1982-12-07
Energy Technology Data Exchange (ETDEWEB)
The aim of this work is to simulate the reduction by hydrogen of the tri-uranium octo-oxide U{sub 3}O{sub 8} (obtained by uranium trioxide calcination) into uranium dioxide. The kinetics curves have been obtained by thermal gravimetric analysis, the hydrogen and steam pressures being defined. The geometrical modeling which has allowed to explain the trend of the kinetics curves and of the velocity curves is an anisotropic germination-growth modeling. The powder is supposed to be formed of spherical grains with the same radius. The germs of the new UO{sub 2} phase appear at the surface of the U{sub 3}O{sub 8} grains with a specific germination frequency. The growth reactivity is anisotropic and is very large in the tangential direction to the grains surface. Then, the uranium dioxide growths inside the grain and the limiting step is the grain surface. The variations of the growth reactivity and of the germination specific frequency in terms of the gases partial ...
1997-12-04
Removal of H2S and SO2 by CaCO3-Based Sorbents at High Pressure
Energy Technology Data Exchange (ETDEWEB)
The theoretical and experimental investigation of the mechanism of SO2 and H2S removal by CaCO3 -based sorbents (limestones and dolomites) in pressurized uidized-bed coal combustors (PFBC) and high pressure gasiers, respectively, is the main objective of this study. It is planned to carry out reactivity evolution experiments under simulated high pressure conditions or in high pressure thermogravimetric and, if needed, uidized- bed reactor (high pressure) arrangements. The pore structure of fresh, heat-treated, and half-calcined solids (dolomites) will be analyzed using a variety of methods. Our work will focus on limestones and dolomites whose reaction with SO2 or H2S under atmospheric conditions has been studied by us or other research groups in past studies. Several theoret- ical tools will be employed to analyze the obtained experimental data including a variable diusivity shrinking-core model and models for diusion, reaction, and structure evolution in ...
1998-02-01
Energy Technology Data Exchange (ETDEWEB)
Mono-dispersed cubic CeO{sub 2} nanoparticles have been synthesized using a surfactant-assisted method with laurylamine hydrochloride and cerium alkoxide modified with acetylacetone in an aqueous solution system. The prepared cubic CeO{sub 2} nanoparticles had a highly crystallized structure at 353 K and formed rod-like structures by calcination at 673 K after freeze-drying the CeO{sub 2} gel. We discovered a clear potential to make 1D, 2D or 3D CeO{sub 2}-materials with a well-controlled characteristic length and shape by assembling cubic-shaped CeO{sub 2} nanoparticle building blocks. CeO{sub 2}-TiO{sub 2} composite nanostructures have also been synthesized by changing the mole ratio of cerium alkoxide/titanium alkoxides. By utilizing the redox characteristic of CeO{sub 2}, CeO{sub 2} nanoparticles and CeO{sub 2}-TiO{sub 2} composite nanostructures after calcination, showed reaction activity toward the oxidization of I{sup -} to I{sub 2}, due ...
2007-07-15
Energy Technology Data Exchange (ETDEWEB)
The fixed bed pilot plant, the catalyst testing procedure, and the calculations for conversion and selectivities were previously described in the technical progress report covering the period of 3/16/88 to 6/16/88 for Contract DE-AC22-87PC79812. Conversions and hydrocarbon selectivities were calculated using data from an on-line gas chromatography (GC) analyzer. Alcohol selectivities were calculated using data from an on-line boiling point GC analyzer which analyzed the liquid product. The catalysts were prepared via the steps of impregnation, calcination, and reduction on a special Y-zeolite-derived support. The impregnation step consisted of evaporation of metal salts on to the support from an aqueous solution. For one catalyst (No. 6531-188) the metal salts were evaporated on to the support from a reverse micelle solution containing the metal salts. All the catalysts were calcined for four hours at 450{degree}C. The ...
1992-12-31
Use plan for demonstration radioactive-waste incinerator
Energy Technology Data Exchange (ETDEWEB)
The University of Maryland at Baltimore was awarded a grant from the Department of Energy to test a specially modified incinerator to burn biomedical radioactive waste. In preparation for the incinerator, the Radiation Safety Office devised a comprehensive plan for its safe and effective use. The incinerator plan includes a discussion of regulations regarding on-site incineration of radioactive waste, plans for optimum use in burning four principal waste forms, controlled air incineration technology, and standard health physics safety practices; a use plan, including waste categorization and segregation, processing, and ash disposition; safety procedures, including personnel and area monitoring; and methods to evaluate the incinerator's effectiveness by estimating its volume reduction factors, mass and activity balances, and by determining the cost effectiveness of incineration versus commercial shallow land burial.
1982-04-01
Sensitivity analysis: Interaction of DOE SNF and packaging materials
International Nuclear Information System (INIS)
A sensitivity analysis was conducted to evaluate the technical issues pertaining to possible destructive interactions between spent nuclear fuels (SNFs) and the stainless steel canisters. When issues are identified through such an analysis, they provide the technical basis for answering what if questions and, if needed, for conducting additional analyses, testing, or other efforts to resolve them in order to base the licensing on solid technical grounds. The analysis reported herein systematically assessed the chemical and physical properties and the potential interactions of the materials that comprise typical US Department of Energy (DOE) SNFs and the stainless steel canisters in which they will be stored, transported, and placed in a geologic repository for final disposition. The primary focus in each step of the analysis was to identify any possible phenomena that could potentially compromise the structural integrity of the canisters and to assess their ...
1999-06-06
Energy Technology Data Exchange (ETDEWEB)
This Waste Management Plan describes waste management and waste minimization activities for Group 3, Other Surface Soils Remediation Sets 4-6 (Phase II) at the Idaho Nuclear Technology and Engineering Center located within the Idaho National Laboratory. The waste management activities described in this plan support the selected response action presented in the Final Record of Decision for Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13. This plan identifies the waste streams that will be generated during implementation of the remedial action and presents plans for waste minimization, waste management strategies, and waste disposition.
2006-07-01
Dynamic characteristics of mixtures of plutonium, Nevada tuff, and water
Energy Technology Data Exchange (ETDEWEB)
One of the technical options being considered for long term disposition of weapons grade plutonium is geologic storage at Yucca Mountain. Multikilogram quantities of plutonium are to be vitrified, placed within a heavy steel container, and buried in the material know as Nevada tuff. It has been postulated that after ten thousand years, geologic and chemical processes would have disintegrated the steel container and created the possibility for plutonium to form mixtures with Nevada tuff and water that could lead to a nuclear explosion in the range of kilotons. A survey and description of critical homogeneous mixtures of plutonium, silicon dioxide, Nevada tuff, and water which also identified the mixture regimes where autocatalytic dynamic behavior is possible was completed. This study is a follow up of this survey and the major objective is to examine the dynamic behavior of the worst case critical and supercritical configurations of plutonium, water and Nevada ...
1996-02-01
Spin injection in quantum wells with spatially dependent rashba interaction
Energy Technology Data Exchange (ETDEWEB)
We consider Rashba spin-orbit effects on spin transport driven by an electric field in semiconductor quantum wells. We derive spin diffusion equations that are valid when the mean free path and the Rashba spin-orbit interaction vary on length scales larger than the mean free path in the weak spin-orbit coupling limit. From these general diffusion equations, we derive boundary conditions between regions of different spin-orbit couplings. We show that spin injection is feasible when the electric field is perpendicular to the boundary between two regions. When the electric field is parallel to the boundary, spin injection only occurs when the mean free path changes within the boundary, in agreement with the recent work by Tserkovnyak et al (Preprint cond-mat/0610190)
2007-09-15
Physical Basis for the Lg/P Discriminant: General Properties and Preliminary Modeling.
A critical problem for reliable implementation of regional discrimination is incomplete understanding of how regional seismic signals depend on physical characteristics of the source and propagation path to the recording station. This research is directed...
1997-01-01
Numerical simulations of quantized Bianchi type IX cosmological models
International Nuclear Information System (INIS)
This paper reports on Monte Carlo path integral simulations of a Bianchi Type IX cosmology which yield a wave function which reflects the known chaotic dynamics of the classical system and predicts a significant probability for a correlation between large universe volume and large anisotropy.
1988-08-08
Energy Technology Data Exchange (ETDEWEB)
With regard to a fracture system in the Hijiori hot dry rock artificial reservoir, an attempt was made on an interpretation which integrates different data. Major factors that characterize development and performance of an artificial reservoir are composed of a fracture system in rocks, which acts as circulating water paths, a heat exchange face and a reservoir space. The system relates not only with crack density distribution, but also with cracks activated by water pressure fracturing, cracks generating acoustic emission (AE), and cracks working as major flow paths, all of which are characterized by having respective behaviors and roles. Characteristics are shown on AE cluster distribution, crack distribution, production zone and estimated stress fields. Mutual relationship among these elements was discussed based on the Coulomb`s theory. The most important paths are characterized by distribution of slippery cracks. ...
1997-05-27
UK PubMed Central (United Kingdom)
Objectives: The purpose of the study was to discover how women found out about uterine fibroid embolization (UFE) for the treatment of symptomatic uterine fibroids.Methods:...Full Text Available
2007-04-01
Heat Transfer Augmentation in a Compact Heat Exchange Pedestal Array.
A compact heat exchanger pedestal array for augmenting heat transfer in a machine is disclosed. The compact heat exchanger pedestal array includes a wall having first and second surfaces. The first surface faces a heated flow path and the second surface p...
2004-01-01
ELECTRONIC COMPONENT COOLING ALTERNATIVES: COMPRESSED AIR AND LIQUID NITROGEN
The goal of this study was to evaluate topics used to troubleshoot circuit boards with known or suspected thermally intermittent components. Failure modes for thermally intermittent components are typically mechanical defects, such as cracks in solder paths or joints, or broken b...
Dissociation dynamics of methylal
Energy Technology Data Exchange (ETDEWEB)
The dissociation of methylal is investigated using mass spectrometry, combined with a pyrolytic radical source and femtosecond pump probe experiments. Based on preliminary results two reaction paths of methylal dissociation are proposed and discussed. (author) 4 fig., 3 refs.
1999-08-01
International Nuclear Information System (INIS)
An earlier representation of the radial distribution of dose about the path of a heavy ion in liquid water is modified and extended to include silicon, lithium fluoride, and sodium iodide. 6 refs., 5 figs., 1 tab.
1989-09-01
Activity-Local Symbolic State Graph Generation for High-Level ...
... ie on all paths from the root to a terminal node we ... (A) A stochastic Petri net ... Tandem Queueing Network [HMKS99] 63 26 19 173 2.297e4 7.148e ...
2005-09-01
A Research Agenda for Malaria Eradication: Drugs
UK PubMed Central (United Kingdom)
Antimalarial drugs will be essential tools at all stages of malaria elimination along the path towards eradication, including the early control or “attack” phase to drive down transmission...Full Text Available
2011-01-01
Interaction between high levels of applied heavy metals and indigenous soil manganese
Energy Technology Data Exchange (ETDEWEB)
The importance of indigenous soil Mn level on plant Mn uptake from metal salt or sewage sludge amended soils was investigated. Twelve soil materials, six surface and six subsurface, were amended with either varying rates of a composite of Cd, Cu, Ni, and Zn sulfate salts, equivalent to the total of these metals present in a digested sewage sludge (Washington, DC) at rates of 0 to 896 dry metric tons/ha or with the sludge itself, at 224 dry metric tons/ha. Corn (Zea mays L.) was grown in the greenhouse for 30 days, 1 year after amendment application. Two pH levels of about 5.5 and 6.5 were maintained during the experiment on the metal salt amended soil materials. Plant tissue Mn levels increased with the application of Cd, Cu, Ni, and Zn (in combination) as metal salts or as sewage sludge over the range of soil materials used. The amount of increase with a given increase in applied metals was greater for the unlimed than for the limed metal salt treatments. Elevated tissue Mn ...
1981-01-01
Quantum Computation with Nonlinear Optics
International Nuclear Information System (INIS)
We propose a scheme of quantum computation with nonlinear quantum optics. Polarization states of photons are used for qubits. Photons with different frequencies represent different qubits. Single qubit rotation operation is implemented through optical elements like the Faraday polarization rotator. Photons are separated into different optical paths, or merged into a single optical path using dichromatic mirrors. The controlled-NOT gate between two qubits is implemented by the proper combination of parametric up and down conversions. This scheme has the following features: (1) No auxiliary qubits are required in the controlled-NOT gate operation; (2) No measurement is required in the course of the computation; (3) It is resource efficient and conceptually simple.
2008-01-15
Off-shell amplitudes for open bosonic strings
Energy Technology Data Exchange (ETDEWEB)
An extension of the Polyakov path-integral formulation to compute off-shell amplitudes for open bosonic strings is derived. Boundary conditions require evaluating the path integral on open surfaces with corners on the boundaries. The contribution to the topological term in the action from the corners is exactly that required for unitarity. The presence of corners introduces a Weyl anomaly in the Polyakov measure. This requires a gauge-fixing procedure for the off-shell amplitudes. Consistent factorization of amplitudes with one or two off-shell strings and any number of on-shell tachyons is established.
1988-02-15
Neutron resonances in /sup 100/Mo and valence neutron capture
Neutron resonance interactions with /sup 100/Mo were studied at a time-of-flight facility. The transmission of two oxide samples (97.4% /sup 100/Mo) was measured at a 78.20 m flight path and the neutron capture cross section was measured at 40.12 m. Resonance analyses yielded parameters of 124 resonances. Capture ..gamma..-ray spectra from 11 resolved resonances were measured with a Ge(Li) detector at a 10.45 m flight path. In contrast to neighboring nuclei, partial radiation widths of strong p-wave resonances are not in agreement with valence model predictions.
1979-07-01
International Nuclear Information System (INIS)
Modelling the behaviour of fission product (FP) in a nuclear reactor coolant system (RCS) undergoing a hypothetical severe accident is an important step in the evaluation of radioactive release outside a nuclear power plant. This paper scrutinize Small Break LOCA sequence for WWER1000 reactor in order to investigate the possible paths for release of FP from fuel pallets to the reactor containment. Contemporaneous computer code for simulation of RCS will be use for the analysis. The results from analysis of fuel damage and release of FP trough the break of cold leg are present. (author)
2006-04-01
British Library Electronic Table of Contents (United Kingdom)
In this work, a new sol-gel auto-combustion method has been performed to synthesize single phase nickel ferrite nanocrystalline powders by using n-cetyltrimethylammonium bromide, as a cationic surfactant. The gels were prepared from ferric and nickel nitrates and citric acid. Ammonia was used as pH adjusting agent as well. The effects of the surfactant on the after combustion calcination process and the reduction of the resulting powder crystallite size which affects the magnetic properties of the material were investigated by XRD and DTA/TGA techniques. The results showed that the ignition of the gels in air have a self-propagating behavior. Addition of surfactant to the starting solution affected the crystallite size of the synthesized powders and their phase constitution. The crystallit...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
An inorganic particulate adsorbent of a titania-alumina is described for treating a superheated water containing radioactive materials such as cobalt ions, which is free from release of corrosive impruities, and which has a high adsorption capacity of radioactive materials and a high mechanical strength is prepared by hydrolyzing a titanium alkoxide and an aluminum alkoxide, thereby forming a hydrous titanium oxide and a hydrous aluminum oxide, respectively; precalcining the hydrous titanium oxide and aluminum oxide, mixing and molding the resulting titania and alumina into a particulate mixture thereof having a titania mole fraction of 0.2 to 0.9, and calcining the particulate mixture at 500/sup 0/-700/sup 0/C. This absorbent is effectively used in treat boiling water-type nuclear reactor core-circulating water to remove radioactive substances therefrom.
1981-08-04
Electrospun porous SnO2 nanotubes as high capacity anode materials for lithium ion batteries
British Library Electronic Table of Contents (United Kingdom)
Porous SnO2 nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807mAhg^-^1 after 50cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO2 nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated t...
2010-01-01
Electrical properties of antimony doped PLZT ceramics prepared by mixed-oxide route
International Nuclear Information System (INIS)
Ferroelectric [Pb_0_._9_2(La_1_-_zSb _z)_0_._0_8][Zr_0_._6_0Ti_0_._4_0]O_3 for z = 0.0, 0.3, 0.6, 0.9 and 1 were prepared from their constituent oxides by a solid state reaction technique. The powders were calcined in the temperature range of 1000 deg. C for 6 h. Phase formation, crystal structure and lattice parameter were investigated by X-ray diffraction (XRD) technique. The compacts were sintered at 1250 deg. C for 2 h and their dielectric, ferroelectric and conductive properties were measured. The ferroelectric behavior of the doped samples was studied from their hysteresis loop.
2006-12-21
Effects of manganese doping on properties of sol-gel derived biphasic calcium phosphate ceramics
British Library Electronic Table of Contents (United Kingdom)
We have investigated the effect of manganese (Mn) doping on properties of nanosized biphasic calcium phosphate powders and their dense bodies. Manganese levels of 0.6, 1.3, 1.9, 4.3, 7.0 and 11.9at.% were successfully incorporated into biphasic calcium phosphate via a sol-gel route. The prepared powders were calcined at temperatures of 500-1200^oC. The X-ray diffraction analysis revealed that a mix phase comprising of hydroxyapatite and @b-tricalcium phosphate were present, however the content of each phases in the structure was affected by the Mn content. The studies found that the largest portion of @b-tricalcium phosphate was detected at 4.3at.% Mn doping. The incorporation of Mn has also greatly increased the crystallinity of the biphasic calcium phosphate powder due to progressive den...
2011-01-01
Development of a pelleted waste form for high-level alumina wastes
Energy Technology Data Exchange (ETDEWEB)
A formulation to pelletize simulated high-level ICPP alumina waste calcine was developed. The pellets are formed on a 41-cm-diameter disc pelletizer using 5% bentonite, 2% metakaolin, and 5 wt % calcium hydroxide as a solid binder and a solution of 7M phosphoric acid and 4M nitric acid as a liquid binder. After drying and heat treatment at 800/sup 0/C for 2 hours, the average crush strength of the pellets is 3.9 MPa and the pellets have a leach resistance of 10/sup -3/ g/cm/sup 2//day, based on Soxhlet leaching for 48 h at 95/sup 0/C with distilled water.
1980-09-01
Desulphurisation of fumes as a potential source of prime materials
Energy Technology Data Exchange (ETDEWEB)
A survey is given by the authors of methods of removing the sulphur dioxide content of fumes which can be linked together with producing useful final products. From these technologies those suppling well utilizable gypsum, the Walther process, producing ammonium sulphate, the Wellman-Lord and Bergbau-Forschung processes, respectively adapted to produce sulphuric acid or sulphur, may be of interest. Also in the method of fumes desulphurisation by catalysis by manganese, developed in KBFI, utilizable final products are given. Background of the work of developing this method. Detailed description of the manganese catalytic method based on the use of a red mud desulphurizing agent. By this process, in addition to desulphurizing fumes, enriched red mud with reduced Na/sub 2/O content is produced, which as an iron carrier, is to be reckoned with, or to be used in the cement industry for replacing imported calcined pyrites.
1986-01-01
Comparison of sodium zirconium phosphate and Synroc matrices for immobilization of high-level waste
Energy Technology Data Exchange (ETDEWEB)
The aims of the present work were to investigate possible compatibility between sodium zirconium phosphate (NZP) and Synroc titanate phases, to prepare NZP-based waste forms by hot-pressing rather than sintering, and to investigate the incorporation in NZP of (a) Cs/Sr as simulated heat-generating nuclides; (b) simulated actinides; and (c) simulated Purex waste. The NZP samples were prepared by methods similar to those used for Synroc. The precursor NZP phase was formed from tetrabutyl zirconate Zr(OC{sub 4}H{sub 9}){sub 4}, sodium nitrate, and 85% orthophosphoric acid. Simulated waste nitrate solutions were then mixed with the liquid precursor. After stir drying of the precursor, calcination was carried out at 700{degree}C to remove nitrates and organics.
1996-12-31
Catalytic tar removal from biomass producer gas with secondary air
Energy Technology Data Exchange (ETDEWEB)
The effect of air addition on biomass tar conversion in catalytic packed bed crackers was studied using both an isothermal micro reactor and a fluidised bed bench scale biomass gasification set up with down stream tar crackers. The micro reactor was applied for experiments with artificial biomass producer gas containing naphthalene as a model tar compound. Experiments were carried out with inert silica and catalytically active calcined dolomite bed material both with and without air addition. Experimental results with real tar from the fluidised bed bench scale gasification set up were in qualitative agreement with results from the micro reactor experiments. (author)
1997-12-31
Catalytic desulfurization of organic sulfur compounds over zeolite catalysts
Energy Technology Data Exchange (ETDEWEB)
In the dehydrodesulfurization of ethanethiol at 400/sup 0/C, the activities of sodium X, Y, and A zeolites decreased in the order given as did the activities of nickel, cobalt, zinc, cadmium, copper, silver, lead, manganese, barium, calcium, sodium, and iron Y zeolite catalysts. A volcano-shape order was observed between the catalytic activity and the electronegativity of the metal ions. The changes in the activity of hydrogen Y zeolite catalyst in ethanethiol dehydrodesulfurization and cumene dealkylation by calcination agreed with the decrease in the Broensted acidity but were independent of Lewis acidity. For hydrodesulfurization of thiophene, the activities of nickel, cobalt, copper, and silver Y zeolite catalysts decreased in the order given and were greater than for a commercial hydrodesulfurization catalyst; reduced and presulfided catalysts showed selective hydrodesulfurization activity. Addition of 5% of nickel or molybdenum oxides to cobalt or nickel Y ...
1980-01-01
CHEMICAL TECHNOLOGY DIVISION. UNIT OPERATIONS SECTION MONTHLY PROGRESS REPORT, FEBRURARY 1963
Development of a shear and leach complex for UO/sub 2/-SS clad fuel was continued with major emphasis on the operation of a rotary drum leacher. Flooding data for nozzle plate pulse columns at high A/O ratios are reported. Engineering tests of dissolution of Zr--6% U alloy with HF in molten salt demonstrated a dissolution rate of 0.8 to 1.5 mg/cm/sup 2//min. Subsequent fluorination with 100% F/sub 2/ proceeded at half times of 40 to 135 min. The results of a high level waste calcination (run R-72) made with formaldehyde treated simulated Purex waste are reported. (auth)
1963-10-01
Anion capture with calcium, aluminium and iron containing layered double hydroxides
British Library Electronic Table of Contents (United Kingdom)
The competitive adsorption of nitrate, chloride and carbonate in layered double hydroxides (LHD) with the general formula Formula Not Shown was investigated. Both normal ion exchange by exposure to a solution containing different anions, as well as addition of calcined material to solution thereby exploiting the memory effect of LDHs was studied. Changes in the interlayer anion changed the interlayer spacing of the LDH. The order of preference of intercalation was Formula Not Shown . When multiple anions were present in the exchange solution, LDHs with several distinct interlayer spacing were produced indicating that LDHs with different anions in the interlayer existed at the same time. However for extended exchange times (14days) where high concentrations of carbonate anion were present, ...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
The combined Lewis and Broensted acidities were measured of 13X (sodium) zeolite and of its 84.2% calcium-exchanged, 86.0% lanthanum-exchanged, and 69.2% protonated forms, calcined at 400/sup 0/C. The butylamine titrations were performed to visible color changes of Hammett indicators. The H/sub 0/ acidities were 0 for the sodium X zeolite, and 0.2, 0.98, and 0.75 for the calcium, lanthanum, and hydrogen zeolites, respectively. These acidities compared well with trends reported in literature for zeolites pretreated under different conditions. Titration of Broensted sites with arylmethanol indicators did not give satisfactory visible endpoints.
1980-05-29
Spent fuel management: Current status and prospects 1993
International Nuclear Information System (INIS)
Spent fuel management has always been one of the most important stages in the nuclear fuel cycle and it is still one of the most vital problems common to all countries with nuclear reactors. It begins with the discharge of spent fuel from a power or a research reactor and ends with its ultimate disposition, either by direct disposal or by reprocessing of the spent fuel. Two options exist at present - an open, once-through cycle with direct disposal of the spent fuel and a closed cycle with reprocessing of the spent fuel and recycling of plutonium and uranium in new mixed oxide fuels. The selection of a spent fuel strategy is a complex procedure in which many factors have to be weighed, including political, economic and safeguards issues as well as protection of the environment. Continuous attention is being given by the IAEA to the collection, analysis and exchange of information on spent fuel management. Its role in this area is to provide a forum for the exchange ...
Short-term energy outlook, Quarterly projections. Third quarter 1993
Energy Technology Data Exchange (ETDEWEB)
The Energy Information Administration (EIA) prepares quarterly, short-term energy supply, demand, and price projections for publication in February, May, August, and November in the Short-Term Energy Outlook (Outlook). An annual supplement analyzes the performance of previous forecasts, compares recent cases with those of other forecasting services, and discusses current topics related to the short-term energy markets. (See Short-Term Energy Outlook Annual Supplement, DOE/EIA-0202.) The forecast period for this issue of the Outlook extends from the third quarter of 1993 through the fourth quarter of 1994. Values for the second quarter of 1993, however, are preliminary EIA estimates (for example, some monthly values for petroleum supply and disposition are derived in part from weekly data reported in the Weekly Petroleum Status Report) or are calculated from model simulations using the latest exogenous information available (for example, electricity sales and ...
1993-08-04
NRC regulatory agenda: Semiannual report, January--June 1997. Volume 16, Number 1
Energy Technology Data Exchange (ETDEWEB)
The Regulatory Agenda is a semiannual compilation of all rules on which the NRC has recently completed action, or has proposed action, or is considering action, and of all petitions for rulemaking that the NRC has received that are pending disposition. The agenda consists of two sections that have been updated through June 30, 1997. Section 1, ``Rules,`` includes (A) rules on which final action has been taken since December 31, 1996, the closing date of the last NRC Regulatory Agenda; (B) rules published previously as proposed rules on which the Commission has not taken final action; (C) rules published as advance notices of proposed rulemaking for which neither a proposed nor final rule has been issued; and (D) unpublished rules on which the NRC expects to take action. Section 2, ``Petitions for Rulemaking,`` includes (A) petitions denied or incorporated into final rules since December 31, 1996; (B) petitions incorporated into proposed rules; and (C) petitions ...
1997-08-01
Methodology for designing air-quality-monitoring networks. 1. Theoretical aspects
Energy Technology Data Exchange (ETDEWEB)
An objective methodology is presented for determining the number and disposition of ambient air-quality stations in a monitoring network for the primary purpose of compliance with air-quality standards. The methodology utilizes a data base with real or simulated data from an air quality dispersion model for application with a two-step process for ascertaining the optimal monitoring network. In the first step, the air-quality patterns in the data base are collapsed into a single composite pattern through a figure-of-merit (FOM) concept. The most-desirable locations are ranked and identified using the resultant FOM fields. In the second step the network configuration is determined on the basis of the concept of spheres of influence (SOI) developed from cutoff values of spatial-correlation coefficients between potential monitoring sites and adjacent locations. The minimum number of required stations is then determined by deletion of lower-ranked stations whose ...
1986-01-01
British Library Electronic Table of Contents (United Kingdom)
Eribulin is a new anticancer agent currently in Phase III clinical trials for the treatment of metastatic breast cancer. In the current studies, we have investigated the effects of P-glycoprotein (P-gp) on the in vivo disposition of eribulin using CF-1 abcb1a-deficient mice, and the influence of eribulin on P-gp-mediated efflux of digoxin in Caco-2 cells. Eribulin was administered intravenously and orally in both CF-1 wild-type and CF-1 abcb1a-deficient mice. P-gp-mediated efflux of digoxin in Caco-2 cell monolayers was measured in the presence of eribulin. The plasma exposure to eribulin was higher in CF-1 abcb1a-deficient mice than that in CF-1 wild-type mice after intravenous (IV) and oral (PO) administrations. The oral bioavailability of eribulin was 62.3% in CF-1 abcb1a-deficient mice...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
In accordance with the Department of Energy`s National Environmental Policy Act implementing procedures in Volume 10 of the Code of Federal Regulations, Section 1021,312, the Environmental Restoration and Waste Management Programmatic Environmental Impact Statement Implementation Plan has two primary purposes: to provide guidance for the preparation of the Programmatic Environmental Impact Statement and to record the issues resulting from the scoping and the extended public participation process. The Implementation Plan identifies and discusses the following: background of Environmental Restoration and Waste Management activities, the purpose of the Programmatic Environmental Impact Statement, and the relationship of the Programmatic Environmental Impact Statement to other Departmental initiatives (Chapter 1); need and purposes for action (Chapter 2); scoping process and results of the public participation program in defining the scope of the Programmatic Environmental Impact ...
1994-01-01
Hanford facility dangerous waste permit application, general information portion
Energy Technology Data Exchange (ETDEWEB)
The `Hanford Facility Dangerous Waste Permit Application` is considered to be a single application organized into a General Information Portion (this document, DOE/RL-91-28) and a Unit- Specific Portion. The scope of the General Information Portion includes information that could be used to discuss operating units, units undergoing closure, or units being dispositioned through other options. Documentation included in the General Information Portion is broader in nature and could be used by multiple treatment, storage, and/or disposal units. A checklist indicating where information is contained in the General Information Portion, in relation to the Washington State Department of Ecology guidance documentation, is located in the Contents Section. The intent of the General Information Portion is: (1) to provide an overview of the Hanford Facility; and (2) to assist in streamlining efforts associated with treatment, storage, and/or disposal unit-specific Part B permit ...
1996-07-29
FY 1987 current fiscal year work plan
Energy Technology Data Exchange (ETDEWEB)
This Current Year Work Plan presents a detailed description of the activities to be performed by the Joint Integration Office during FY87. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance, task monitoring, information gathering and task reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of program status reports for DOE. Program Analysis is ...
1986-12-01
Evaluation of light-water-moderated, mixed-oxide, hexagonal pitch lattices
International Nuclear Information System (INIS)
The use of previously measured mixed-oxide (MOX) fuel systems as benchmarks can be valuable tool in computational analysis and quality assurance efforts. The Fissile Materials Disposition Program (FMDP) has identified these experiments as potential benchmarks, or standards, for VVER's employing MOX fuel. Standards for the analysis of these benchmark experiments were based on those used in the recent compilation International Handbook of Evaluated Criticality Safety Benchmark Experiments begun in 1992 by the U.S. Department of Energy. The Los Alamos National Laboratory's archives were explored for log-book records of these experiments without success. These experiments were the first to use MOX fuel in light water. Three approach-to-critical experiments were performed using fuel rods at various pitches and different plutonium-oxide concentrations. A parallel program verified the prediction of critical condition as similar materials and geometries were actually ...
1997-11-16
Estimation of vapour pressure over MOX fuel
International Nuclear Information System (INIS)
Use of high plutonia MOX as fuel is contemplated from the point of view of rapid disposition of plutonium and economic power generation. The fuel pellets are subjected to steep thermal gradients #approx# 1700 K drop across a radius of #approx# 2.5mm. This leads to evaporation-condensation of the fuel constituents to cooler regions. Vaporization depends on fuel compositions such as Pu fraction, Oxygen-to-Metal (O/M) ratio and local temperature. Knowledge of vapour chemistry is essential in understanding the fuel behavior. The vaporization behaviour of MOX was analyzed in this work using thermochemical methods. The vapour phase consisted of nine species; O, O_2, Pu, PuO, PuO_2, U, UO, UO_2 and UO_3. Oxygen formed part of the vapour phase along with other species and oxygen potential was not controlled independently. The vapour pressures were estimated at 2000 K as a function of (O/M) for several Pu-fraction. Results for MOX-28%PuO_2 is shown in the study. The results ...
2010-12-01
Biocatalytic desulfurization of petroleum and middle distillates
Energy Technology Data Exchange (ETDEWEB)
Biocatalytic Desulfurization (BDS) represents an alternative approach to the reduction of sulfur in fossil fuels. The objective is to use bacteria to selectively remove sulfur from petroleum and middle distillate fractions, without the concomitant release of carbon. Recently, bacteria have been developed which have the ability to desulfurize dibenzothiophene (DBT) and other organosulfur molecules. These bacteria are being developed for use in a biocatalyst-based desulfurization process. Analysis of preliminary conceptual engineering designs has shown that this process has the potential to complement conventional technology as a method to temper the sulfur levels in crude oil, or remove the recalcitrant sulfur in middle distillates to achieve the deep desulfurization mandated by State and Federal regulations. This paper describes the results of initial feasibility studies, sensitivity analyses and conceptual design work. Feasibility studies with various crude oils and middle distillates ...
1993-02-01
Energy Technology Data Exchange (ETDEWEB)
An economic analysis of the potential advantages of alternatives for recycling and reusing equipment now stored in Building 865 at the Rocky Flats Plant (RFP) in Colorado has been conducted. The inventory considered in this analysis consists primarily of metallurgical and process equipment used before January 1992, during development and production of nuclear weapons components at the site. The economic analysis consists of a thorough building inventory and cost comparisons for four equipment dispositions alternatives. The first is a baseline option of disposal at a Low Level Waste (LLW) landfill. The three alternatives investigated are metal recycling, reuse with the government sector, and release for unrestricted use. This report provides item-by-item estimates of value, disposal cost, and decontamination cost. The economic evaluation methods documented here, the simple cost comparisons presented, and the data provided as a supplement, should provide a foundation ...
1993-08-01
Review of high-level waste form properties. [146 bibliographies
Energy Technology Data Exchange (ETDEWEB)
This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum properties over the entire range of characteristics investigated. A long-term effort has been applied to the development of glass and calcine waste forms. Several ...
1980-12-01
Lubricating composition for processing of flushing fluids
Energy Technology Data Exchange (ETDEWEB)
Proposed is a lubricating composition for processing flushing fluids, which contains synthetic fatty acids of the fraction carbon 11-20, oxidized petrolatum, mineral oil, and additives. In order to increase the antiwear, anticorrosion, and antiscratching properties of the composition under conditions of polymineral corrosion with simultaneous decrease in the water loss of the flushing fluids as additives the composition contains stearic acid, polyoxyethylated methyl phenol, naptha soap, 1,5-dibenzoylnapthaline-4', 4''-dicarboxylic acid, calcined soda, secondary nonsaponifiables, obtained in the production of synthetic fatty acids by oxidation of paraffin, and polyfunctional oxygen-bearing compounds, obtained by oxidation of secondary nonsaponifiables by atmospheric oxygen, with the following ratio of components, wt%: 17.2-19.2% synthetic fatty acids of the carbon 17-20 fraction, 5.2-5.8% oxidized petrolatum, 3.5-3.7% polyoxyethylated ...
1981-03-15
Vulnerability Analysis of Physical Protection System at Wolsung Nuclear Power Plant
Energy Technology Data Exchange (ETDEWEB)
The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of an existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several methods are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsung NPP using SAVI code. First, the site-specific Adversary Sequence Diagrams(ASDs) of the PPS is constructed. It helps to understand the functions of the existing PPS composed of physical areas and Protection Elements(PEs) at Wolsung NPP. Then, the most ...
2006-07-01
Vulnerability Analysis of Physical Protection System at Wolsung Nuclear Power Plant
International Nuclear Information System (INIS)
The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of an existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several methods are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsung NPP using SAVI code. First, the site-specific Adversary Sequence Diagrams(ASDs) of the PPS is constructed. It helps to understand the functions of the existing PPS composed of physical areas and Protection Elements(PEs) at Wolsung NPP. Then, the most ...
2006-05-25
Performance Assessment of Physical Protection System at Wolsong Nuclear Power Plant using SAVI code
Energy Technology Data Exchange (ETDEWEB)
The 9/11 event in the U.S.A has increased international terror possibilities against nuclear facilities including nuclear power plants(NPPs). It is necessary to assess the performance of existing physical protection system(PPS) at nuclear facilities based on such malevolent acts. A PPS is a complex configuration of detection, delay, and response elements. Several techniques are available to analyze a PPS and evaluate its effectiveness. Sandia National Laboratory(SNL) in the USA was developed a System Analysis of Vulnerability to Intrusion (SAVI) computer code for this purpose. It is powerful software for evaluating the effectiveness of PPS against outsider threats. This study presents the performance assessment of the PPS at Wolsong NPP using SAVI code. The first is that the SAVI constructs the site-specific Adversary Sequence Diagram (ASD) of the PPS. This provides a methods of graphically representing the PPS composed of physical areas and Protection Elements(PEs) at Wolsung NPP. The ...
2005-07-01
Nearly metastable rhombohedral phases of bcc metals
International Nuclear Information System (INIS)
The energy E(c/a) for a bcc element stretched along its [001] axis (the Bain path) has a minimum at c/a=1, a maximum at c/a=#sq root#(2), and an elastically unstable local minimum at c/a>#sq root#(2). An alternative path connecting the bcc and fcc structures is the rhombohedral lattice. The primitive lattice has R3m symmetry, with the angle #alpha# changing from 109.4 deg. (bcc), to 90 deg. (simple cubic), to 60 deg. (fcc). We study this path for the non-magnetic bcc transition metals (V, Nb, Mo, Ta, and W) using both all-electron linearized augmented plane wave and projector augmented wave VASP codes. Except for Ta, the energy E(#alpha#) has a local maximum at #alpha#=60 deg., with local minima near 55 deg. and 70 deg., the latter having lower energy, suggesting the possibility of a metastable rhombohedral state for these materials. We first examine the elastic stability of the 70 deg. minimum structure, and determine ...
2008-02-01
Topological Analysis of Large-scale Biomedical Terminology Structures
British Library Electronic Table of Contents (United Kingdom)
ObjectiveTo characterize global structural features of large-scale biomedical terminologies using currently emerging statistical approaches.DesignGiven rapid growth of terminologies, this research was designed to address scalability. We selected 16 terminologies covering a variety of domains from the UMLS Metathesaurus, a collection of terminological systems. Each was modeled as a network in which nodes were atomic concepts and links were relationships asserted by the source vocabulary. For comparison against each terminology we created three random networks of equivalent size and density.MeasurementsAverage node degree, node degree distribution, clustering coefficient, average path length.ResultsEight of 16 terminologies exhibited the small-world characteristics of a short average path le...
2007-01-01
The Meaning of Cause and Prevent: The Role of Causal Mechanism
British Library Electronic Table of Contents (United Kingdom)
How do people understand questions about cause and prevent? Some theories propose that people affirm that A causes B if A's occurrence makes a difference to B's occurrence in one way or another. Other theories propose that A causes B if some quantity or symbol gets passed in some way from A to B. The aim of our studies is to compare these theories' ability to explain judgements of causation and prevention. We describe six experiments that compare judgements for causal paths that involve a mechanism, i.e. a continuous process of transmission or exchange from cause to effect, against paths that involve no mechanism yet a change in the cause nevertheless brings about a change in the effect. Our results show that people prefer to attribute cause when a mechanism links cause to effect. In contr...
2011-01-01
Particle Swarm Optimization for Realizing Intelligent Routing in Networks with Quality Grading
Significant research has been carried out in the recent years for generating systems exhibiting intelligence for realizing optimized routing in networks. In this paper, a grade based twolevel based node selection method along with Particle Swarm Optimization (PSO) technique is proposed. It assumes that the nodes are intelligent and there exist a knowledge base about the environment in their local memory. There are two levels for approaching the effective route selection process through grading. At the first level, grade based selection is applied and at the second level, the optimum path is explored using PSO. The simulation has been carried out on different topological structures and it is observed that a graded network produces a significant reduction in number of iteration to arrive at the optimal path selection.
2011-01-01
British Library Electronic Table of Contents (United Kingdom)
This study presents new software, called Google Earth-based Optimal HAulage RouTing System (GEOHARTS), to improve the functionality of Google Earth for optimal haulage routing of off-road dump trucks in construction and mining sites. A modified least-cost path algorithm, which is applicable to working areas with both paved and unpaved temporary roads and can consider the effects of terrain relief and curves along a route on the route planning, was proposed and utilized for the software development. GEOHARTS can determine optimal haulage routes between loaders and dumps that ensure the least travel time or fuel consumption of off-road dump trucks and can visualize the results using an embedded 3D render window of Google Earth. The application to the Pasir open-pit coal mine in Indonesia dem...
2011-01-01
Neutron resonances in "1"0"0Mo and valence neutron capture
International Nuclear Information System (INIS)
Neutron resonance interactions with "1"0"0Mo were studied at a time-of-flight facility. The transmission of two oxide samples (97.4% "1"0"0Mo) was measured at a 78.20 m flight path and the neutron capture cross section was measured at 40.12 m. Resonance analyses yielded parameters of 124 resonances. Capture #gamma#-ray spectra from 11 resolved resonances were measured with a Ge(Li) detector at a 10.45 m flight path. In contrast to neighboring nuclei, partial radiation widths of strong p-wave resonances are not in agreement with valence model predictions.
Low-cycle fatigue behaviour and microstructure of copper and alpha-brass under biaxial load paths
Energy Technology Data Exchange (ETDEWEB)
The low-cycle fatigue behaviour of copper and a-brass CuZn30 was investigated in uniaxial and biaxial tests. Planar biaxial fatigue tests were carried out using cruciform samples with proportional stain paths with and without phase shift between the two axes. Microcharacterisation was performed by electron microscopy as well as by high-resolution X-ray line profile analysis. The biaxial cyclic stress-strain curves show good agreement with the uniaxial ones using the von Mises equivalent strain hypothesis. The dislocation densities and microhardness values of the biaxial case, however, show significantly lower values compared to the uniaxial case at equivalent von Mises stresses.
2010-07-01
Linac Coherent Light Source Experiments Commence
British Library Electronic Table of Contents (United Kingdom)
The Linac Coherent Light Source [1] (LCLS) at SLAC National Accelerator Laboratory is preparing for the arrival of its first scientific users in the fall of 2009. LCLS is the world's first free-electron in the spectral range 800-8,000 eV, producing intense, sub-picosecond pulses of Xrays with very high spatial coherence. The accelerator facility has been commissioned in stages, beginning in April 2007 [2] with the injector linac and culminating in December 2008 [3] with the first transport of electrons through the complete beam path. On April 10, 2009, the LCLS Project team was rewarded for years of planning, design, construction, and checkout with a dream-come-true: as undulators were placed on the beam path one-by-one, the laser simply turned on without drama in the course of one hour [4...
2009-01-01
High channel density wavelength division multiplexer with defined diffracting means positioning
Energy Technology Data Exchange (ETDEWEB)
A wavelength division multiplexer/demultiplexer having optical path lengths between a fiber array and a Fourier transform lens, and between a dispersion grating and the lens equal to the focal length of the lens. The optical path lengths reduce losses due to angular acceptance mismatch in the multiplexer. Close orientation of the fiber array about the optical axis and the use of a holographic dispersion grating reduces other losses in the system. Multi-exposure holographic dispersion gratings enable the multiplexer/demultiplexer for extremely broad-band simultaneous transmission and reflection operation. Individual Bragg plane sets recorded in the grating are dedicated to and operate efficiently on discrete wavelength ranges.
1990-01-01
Exact Simulation of Bessel Diffusions
We consider the exact path sampling of the squared Bessel process and some other continuous-time Markov processes, such as the CIR model, constant elasticity of variance diffusion model, and hypergeometric diffusions, which can all be obtained from a squared Bessel process by using a change of variable, time and scale transformation, and/or change of measure. All these diffusions are broadly used in mathematical finance for modelling asset prices, market indices, and interest rates. We show how the probability distributions of a squared Bessel bridge and a squared Bessel process with or without absorption at zero are reduced to randomized gamma distributions. Moreover, for absorbing stochastic processes, we develop a new bridge sampling technique based on conditioning on the first hitting time at zero. Such an approach allows us to simplify simulation schemes. New methods are illustrated with pricing path-dependent options.
2009-01-01
Epitaxial bain path in transition metals
Energy Technology Data Exchange (ETDEWEB)
Epitaxial films grown pseudomorphically on substrates provide a way to stabilise non-equilibrium structures of materials. Obviously, there always is a certain lattice misfit between substrate and film material in its bulk equilibrium structure. In the pseudomorphic regime, this misfit can either lead to the growth of films in a strained bulk structure or even yield structures that are not stable in the bulk. Large misfits do not necessarily imply large lateral stress. Theory can help to predict e.g. geometry, stress and magnetic properties of pseusomorphically grown metal films. In this work, we considered the fcc-bcc epitaxial Bain path of 3d, 4d, and 5d transition metals, which provides a reasonable description of tetragonally distorted films on substrates. We carried out density functional calculations in the implementation of the full potential local orbital program package FPLO. Emphasis is put on similarities among the transition metals.
2010-07-01
British Library Electronic Table of Contents (United Kingdom)
Changing water demands induced through climate change and a growing biofuel energy sector throughout the western States are expected to increase pressures on the present allocation mechanisms for an increasingly scarce resource, raising uncertainty about the sustainability of irrigated agriculture in the West. In this paper, we first present the policy motivation for examining continued producer adoption of water conserving irrigation production systems as a foundation for providing a sustainable future for western irrigated agriculture. Second, we summarize the historical transitions that help to define the adjustment path to increased sustainability for the sector. While western irrigated agriculture is on a path toward greater sustainability, evidence suggests that the sustainability go...
2010-01-01
We introduce a new formulation of asset trading games in continuous time in the framework of the game-theoretic probability established by Shafer and Vovk (2001). In our formulation, the market moves continuously but an investor trades in discrete times, which can depend on the past path of the market. We prove that an investor can essentially force that the asset price path behaves with the variation exponent exactly equal to two. Our proof is based on embedding high-frequency discrete time games into the continuous time game and the use of the Bayesian strategy of Kumon, Takemura and Takeuchi (2007b) for discrete time coin-tossing games. We also clarify that the main growth part of the investor's capital processes is lucidly described by the information quantities, which are derived from the Kullback-Leibler information with respect to the empirical fluctuation of the asset price.
2007-01-01
Watching Systems in graphs: an extension of Identifying Codes
We introduce the notion of watching systems in graphs, which is a generalization of that of identifying codes. We give some basic properties of watching systems, an upper bound on the minimum size of a watching system, and results on the graphs which achieve this bound; we also study the cases of the paths and cycles, and give complexity results.
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
The study concerns 1984-1991. The wind park consists of 18 three-bladed 300 kW horizontal axis wind turbines of 35 meters height, and a rotor diameter of 30 meters, seven meteorological towers, and three cluster and control buildings. Aspects studied included disturbance of breeding, resting or feeding, and migrating birds, behavior of birds approaching the wind turbines during the day and night, and bird victims due to collision with the wind turbines and the meteorological towers. The flight behavior of birds approaching the wind park system during daylight is also dealt with. For at least a fifth of the observations it was noted whether the birds passing within 100 meters distance of a turbine showed a reaction or not. The proportion of the reactions was related to the wind park in operation or not in operation, and to the distance between the wind turbines, species, flight height, the passing distance, wind direction and wind force. Secondly the flight path of ...
1992-01-01
International Nuclear Information System (INIS)
Energy policy is discussed, with particular reference to Scotland. The plans for nuclear power are analyzed in comparison with developments in coal mining, use of oil and gas and other possible energy sources such as wind and wave power. Arguments against the development of nuclear power are raised on grounds of economics, employment potential, and problems of waste disposal. (U.K.).
1979-03-01
New concept in transmission line reclosure using high-frequency fault transients
Energy Technology Data Exchange (ETDEWEB)
The authors present a new concept: 'adaptive optimal reclosure' under transmission line faults by integrating the adaptive and optimal reclosure techniques. Simulation studies prove that the proposed technique is able to first detect the persistence time of fault path arc and then capture the optimal reclosure time, thereby enhancing system stability. (author)
1997-07-01
Influence of rotation on the initial state of the Universe
Energy Technology Data Exchange (ETDEWEB)
We apply Hawking's proposal for the initial state of the Universe to a rotating Bianchi type-IX minisuperspace model in order to examine the problem of rotation in a closed cosmology. Using the Feynman path-integral techniques instead of the Wheeler-DeWitt equation, we are able to say that for a small angular velocity the closed Friedmann-Robertson-Walker model is indeed the most probable initial state for the Universe.
1989-12-15
Influence of rotation on the initial state of the Universe
International Nuclear Information System (INIS)
We apply Hawking's proposal for the initial state of the Universe to a rotating Bianchi type-IX minisuperspace model in order to examine the problem of rotation in a closed cosmology. Using the Feynman path-integral techniques instead of the Wheeler-DeWitt equation, we are able to say that for a small angular velocity the closed Friedmann-Robertson-Walker model is indeed the most probable initial state for the Universe.
International Nuclear Information System (INIS)
Hydrology and hydrogeochemical are auxiliary techniques to valid conceptual hydrogeology an recharge models. Stable isotopes from water trace sources and path flow and Tritium indicates age. This paper is about the use of D 18, D2H y 3H to study the aquifer system on Bajo Cauca antioqueno.
Halflives of rp-Process Waiting Point Nuclei
Energy Technology Data Exchange (ETDEWEB)
The fragment separator at GSI, Darmstadt, has been used to produce and separate very proton rich nuclei in the {sup 100}Sn region. By fragmentation of a {sup 112}Sn beam at 1 A{center_dot}GeV we produced nuclei along the rp-process path between {sup 77}Y and {sup 98}In. By implanting these ions into a silicon detector stack we were able to determine their halflives. Preliminary data are presented.
1999-12-31
Solids are separated from a liquid in a gravity settler provided with inclined solid intercepting surfaces to intercept the solid settling path to coalesce the solids and increase the settling rate. The intercepting surfaces are inverted V-shaped plates, each formed from first and second downwardly inclined upwardly curved intersecting conical sections having their apices at the vessel wall.
1979-01-01
Energy Technology Data Exchange (ETDEWEB)
A fuel injector comprises first and second housing parts, the first housing part being located within a bore or recess formed in the second housing part, the housing parts defining therebetween an inlet chamber, a delivery chamber axially spaced from the inlet chamber, and a filtration flow path interconnecting the inlet and delivery chambers to remove particulate contaminants from the flow of fuel therebetween.
2001-02-27
Fuel ignition by high voltage capacitive discharges
Energy Technology Data Exchange (ETDEWEB)
The study examined the possibility for fuel ignition by spark discharge caused by induction effects under high voltage transmission lines. Theoretical background information on capacitive spark discharges and fuel ignition processes is given. Laboratory experiments were conducted to test the dependence of fuel ignition on three parameters: impedance in discharge path, multiple discharges, and larger electrode shapes. The results of these tests are discussed in terms of fuel ignition possibilities under high voltage transmission lines.
1983-03-01
Feynman rules for gauge fields in the presence of a dielectric medium
Energy Technology Data Exchange (ETDEWEB)
T. D. Lee's method for developing the Feynman rules for gauge fields in a cavity is reformulated in terms of path integral. His work is then extended by deriving these rules, in the Feynman gauge, for a spherical cavity. In any gauge only the gauge particle propagator is altered, while all the Feynman rules for gauge field couplings are left unaltered by the presence of a dielectric medium.
1983-10-15
Experimental and evaluated nuclear plus interference cross sections for light charged particles
Energy Technology Data Exchange (ETDEWEB)
Experimental and evaluated integral parameters derived from nuclear plus interference differential elastic scattering cross sections are presented for all projectile/target combinations of the particles p, d, t, /sup 3/He, and ..cap alpha... The data include reaction rates, average fractional energy losses per collision and per unit path length, and average laboratory scattering cosines. The resulting parameters are of potential use in analysis of charged-particle transport.
1980-07-04
Device for marking and searching for information on a magnetic carrier
A device for marking and searching for information on a magnetic carrier is described. In order to increase the noise immunity and reliability of the data recording and reading paths, the recording head is included between the amplifier of the clock pulses for the master oscillator and through the amplifier of the code pulses for the logical element unit. The reproduction head is connected through the code pulse shaper-amplifier with a switch which is connected with the display unit, and through another analogous clock pulse amplifier with a multivibrator.
1984-03-01
CLIC High-Gradient Test Results
The CLIC (Compact Linear Collider) high-gradient RF structure testing program has been carried out in order to gain insight into the physical processes involved in RF breakdown, determine the mechanisms that limit gradient and produce damage so that technical concepts can be developed which allow higher accelerating gradients. Two main paths towards higher gradients have emerged from this program, and the performances of two new structures which incorporate them are presented.
2002-01-01
Adiabatic theory of Wannier threshold laws and ionization cross sections
Energy Technology Data Exchange (ETDEWEB)
The Wannier threshold law for three-particle fragmentation is reviewed. By integrating the Schroedinger equation along a path where the reaction coordinate R is complex, anharmonic corrections to the simple power law are obtained. These corrections are found to be non-analytic in the energy E, in contrast to the expected analytic dependence upon E.
1994-12-31
A New DC Breaker Used as Metallic Return Transfer Breaker.
Energy Technology Data Exchange (ETDEWEB)
When a bipolar HVDC transmission system is operating monopolar using the earth as a return path, it is often desired to divert the return current from the earth to the line from the unused pole. To do so requires either that the system be shut down temporarily or that a dc circuit breaker be used. This paper describes the development of such a new dc circuit breaker, and its application on the Pacific Intertie as a Metallic Return Transfer Breaker (MRTB).
1982-10-01
Synthesis of nanocrystalline YSZ (ZrO_2-8Y_2O_3) powder by polymerized complex method
International Nuclear Information System (INIS)
In this study nanocrystalline powders of yttria-stabilized zirconia (ZrO_2-8Y_2O_3) have been synthesized through 'polymerized complex method'. Zirconium chloride, yttrium nitrate, citric acid and ethylene glycol were polymerized at 80 "oC to produce a gel-like mass in which metallic ions were uniformly distributed. During the thermal treatment of dried gel, nanocrystalline powder was formed at 450 "oC and 650 "oC for 2 h. Thermal reactions and crystalline phase formation of the dried gel were investigated through thermal analysis and X-ray diffraction analysis, respectively. The results of thermal analysis and XRD showed the formation of nanocrystalline powder at less than 600 "oC. Chemical bonding of the dried gel was investigated by Fourier transform infrared spectroscopy analysis. Morphology of powder calcined at 650 "oC was analyzed by scanning electron microscope. Yttria-stabilized zirconia powders with the mean crystallite size of 6 nm were prepared ...
2010-02-18
Synthesis of ?-Al2O3 nanowires through a boehmite precursor route
British Library Electronic Table of Contents (United Kingdom)
Crystalline ?-Al2O3 nanowires with diameter, 20?40?nm, length above 600?nm and aspect ratio above 30 have been successfully synthesized by thermal decomposition of boehmite (?-AlOOH) precursors obtained via hydrothermal route by using AlCl3, NaOH and NH3 as starting materials. Thermogravimetric analysis (TG), differential thermal analysis (DTA), X-ray diffraction (XRD), transmission electron microscope (TEM), selected area electron diffraction (SAED) and high resolution transmission electron microscope (HRTEM) were used to characterize the features of the as-made ?-Al2O3 nanowires and their ?-AlOOH precursors. The pH value of the solution and the mixed precipitant play important roles in the formation of ?-AlOOH nanowires. After calcination at 500?C for 2?h, the orthorhombic ?-AlOOH transf...
2011-01-01
Synthesis and electrochemical performance of carbon nanofiber-cobalt oxide composites
Energy Technology Data Exchange (ETDEWEB)
Carbon nanofiber (CNF) supported cobalt oxide composites as high-capacity anode materials were prepared through a facile, effective method for potential use in rechargeable lithium-ion batteries. The effects of the calcining temperature on the crystallinity, grain size, specific surface area of Co{sub 3}O{sub 4} and phase transformation from Co{sub 3}O{sub 4} to CoO were studied in detail. Both the specific surface area and CNF content in CNF-cobalt oxide composites strongly affect the electrochemical performance of these series composites. The CNF-Co{sub 3}O{sub 4} composite with 24.3% CNF pyrolyzed at 500 deg. C in Ar shows an excellent cycling performance, retaining a specific capacity of 881 mAh g{sup -1} beyond 100 cycles. Homogeneous deposition and distribution of nanosized Co{sub 3}O{sub 4} particles on the surface of CNF can stabilize the electronic and ionic conductivity as well as the morphology of Co{sub 3}O{sub 4} phase, which may be the main reason for ...
2008-10-15
Synthesis and electrochemical performance of carbon nanofiber-cobalt oxide composites
Energy Technology Data Exchange (ETDEWEB)
Carbon nanofiber (CNF) supported cobalt oxide composites as high-capacity anode materials were prepared through a facile, effective method for potential use in rechargeable lithium-ion batteries. The effects of the calcining temperature on the crystallinity, grain size, specific surface area of Co{sub 3}O{sub 4} and phase transformation from Co{sub 3}O{sub 4} to CoO were studied in detail. Both the specific surface area and CNF content in CNF-cobalt oxide composites strongly affect the electrochemical performance of these series composites. The CNF-Co{sub 3}O{sub 4} composite with 24.3% CNF pyrolyzed at 500{sup o}C in Ar shows an excellent cycling performance, retaining a specific capacity of 881 mAh g{sup -1} beyond 100 cycles. Homogeneous deposition and distribution of nanosized Co{sub 3}O{sub 4} particles on the surface of CNF can stabilize the electronic and ionic conductivity as well as the morphology of Co{sub 3}O{sub 4} phase, which may be the main reason ...
2008-10-15
Energy Technology Data Exchange (ETDEWEB)
Praseodymium-doped Bi{sub 4}Ti{sub 3}O{sub 12} (BIT) with various compositions of dopant, Pr (x = 0.5, 0.6, 0.7, 0.8) in Bi{sub 4-x}Pr{sub x}Ti{sub 3}O{sub 12} (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800 deg. C exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x = 0.5) resulted in dramatically reduced of grain size from 2 {mu}m to less than 50 nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1 {mu}m was observed for x = 0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the addition of x = 0.50, and increasing with further addition of Pr. Dissipation factor (tan {delta}) followed the same trend ...
2009-05-05
International Nuclear Information System (INIS)
Praseodymium-doped Bi_4Ti_3O_1_2 (BIT) with various compositions of dopant, Pr (x = 0.5, 0.6, 0.7, 0.8) in Bi_4_-_xPr_xTi_3O_1_2 (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800 deg. C exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x = 0.5) resulted in dramatically reduced of grain size from 2 #mu#m to less than 50 nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1 #mu#m was observed for x = 0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the addition of x = 0.50, and increasing with further addition of Pr. Dissipation factor (tan #delta#) followed the same trend as dielectric constant that was ...
2009-05-05
British Library Electronic Table of Contents (United Kingdom)
Praseodymium-doped Bi4Ti3O12 (BIT) with various compositions of dopant, Pr (x=0.5, 0.6, 0.7, 0.8) in Bi4-xPrxTi3O12 (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800degreeC exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x=0.5) resulted in dramatically reduced of grain size from 2mm to less than 50nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1mm was observed for x=0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the ad...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
Stearic acid gel is employed to study the phase evolution of MgTiO{sub 3} nanoparticles by thermal gravimetric analysis, X-ray diffraction, and Fourier transform infrared. During the preparation of stearic acid gel, tetrabutyl titanate easily absorbed moisture to hydrolyze into Ti(OH){sub 4} firstly, and then reacts with stearic acid and magnesium stearate to form magnesium-titanium oxide network polymer gel, meanwhile n-butanol is generated. When stearic acid gel is calcined in air, a series of oxidation and combustion reactions occur, meanwhile apparent heat is given off. The results show that a metastable intermediate phase Mg{sub 2}TiO{sub 4} is generated at 450 {sup o}C and nearly disappeared at 550 {sup o}C. Simultaneously, a new solid phase of MgTiO{sub 3} appears. The metastable intermediate phase Mg{sub 2}TiO{sub 4} is successfully identified in the current work.
2010-03-04
Silylated Co/SBA-15 catalysts for Fischer-Tropsch synthesis
International Nuclear Information System (INIS)
A series of silylated Co/SBA-15 catalysts were prepared via the reaction of surface Si-OH of SBA-15 with hexamethyldisilazane (HMDS) under anhydrous, vapor-phase conditions, and then characterized by FT-IR, N2 physisorption, TG, XRD, and TPR-MS. The results showed that organic modification led to a silylated SBA-15 surface composed of stable hydrophobic Si-(CH3)3 species even after calcinations and H2 reduction at 673 K. Furthermore, the hydrophobic surface strongly influenced both metal dispersion and reducibility. Compared with non-silylated Co/SBA, Co/S-SBA (impregnation after silylation) showed a high activity, due to the better cobalt reducibility on the hydrophobic support. However, S-Co/SBA (silylation after impregnation) had the lowest FT activity among all the catalysts, due to the lower cobalt reducibility along with the steric hindrance of grafted -Si(CH3)3 for the re-adsorption of ?-olefins. -- Graphical abstract: The silylation of an SBA-15 before ...
2011-03-01
Energy Technology Data Exchange (ETDEWEB)
Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the oxidation of volatile organic compounds. The study showed that red mud can be used as a catalyst for the oxidation of toluene. ...
2005-08-01
Novel alloys to improve the electrochemical behavior of zinc anodes for zinc/air battery
Energy Technology Data Exchange (ETDEWEB)
In our continued efforts for improving the performance of zinc anodes for a Zn/air battery, we now report the preparation of three alloys and improved performances of anodes made up with these alloys. The alloys contained zinc, nickel, and indium with different weight percentages and were calcined at two different temperatures. Out of the six alloys, the alloy which has a composition of zinc 90%, nickel 7.5% and Indium 2.5% and fired at 500{sup o}C is found to be the best. In the case of the hydrogen evolution reaction, this alloy had its potential shifted to a more negative potential. As far as the cyclic voltammograms were concerned, the difference between the anodic and cathodic part was minimal when compared with other alloys. Surprisingly, this alloy had reversibility even after 100 cycles of the cyclic voltammogram. This is a clear indication that dendrite formation was reduced to a considerable extent. Images taken with a scanning electron microscope also ...
2006-10-06
Neutron shielding and constructional characteristics of a new type concrete and from borated clinker
International Nuclear Information System (INIS)
A boron containing cement, which can be used as nuclear shielding material, is produced at pilot plant scale applying two different methods. In the first method, the raw mixture of a normal portland cement is mixed with pre-calcined colemanite, a calcium borate mineral, and clinkerized in a rotary kiln (borated-clinker). In the second method, the colemanite is mixed with an admixture, which contains mainly limestone and marl, and burnt in the rotary kiln to obtain a borated-lime composite. The borated-lime composite is then added to the normal portland cement clinker up to 2% B_2O_3 content for shielding purpose. The results have shown that the borated-clinker contained untolerable amount of free lime resulting in a decrease in compressive strength. The addition of the borated-lime composite to the normal portland cement clinker up to 1% B_2O_3 content did not alter the setting time and the volume expansion properties. The reduction in the compressive strength was ...
1994-11-07
High pressure thermogravimetric analysis of the direct sulfation of Spanish calcium-based sorbents
Energy Technology Data Exchange (ETDEWEB)
Under typical conditions found in Pressurized Fluidized Bed Combustion (PFBC), the calcination reaction of limestones is thermodynamically inhibited, and the sorbent reacts with SO{sub 2} by a direct mechanism. Direct sulfation reactivity of different Spanish sorbents was studied by high-pressure thermogravimetric analysis. It was found that the physical structure of the surface of the particles influence the sulfation behaviour of the sorbents. Total pore volume and pore surface area correlated well with the reactivity of the sorbents. Temperatures between 800 and 925{degree}C, and pressure between 12 and 25 bar, promoted an increase in reactivity, while the gas composition had no effect when changed from 15% CO{sub 2}, 3% O{sub 2}, 0.5% SO{sub 2}, balance N{sub 2} to 12% CO{sub 2}, 7% O{sub 2}, 0.5% SO{sub 2}, balance N{sub 2}. It was found that the unreacted shrinking core model could not satisfactorily describe the sulfation reaction under the conditions ...
1999-02-01
Energy Technology Data Exchange (ETDEWEB)
Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial replacement of cement, as new ...
2010-07-01
Evaluation of red mud as pozzolanic material in replacement of cement for production of mortars
International Nuclear Information System (INIS)
Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial replacement of cement, as new ...
2010-11-21
Electrospun porous SnO{sub 2} nanotubes as high capacity anode materials for lithium ion batteries
Energy Technology Data Exchange (ETDEWEB)
Porous SnO{sub 2} nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807 mAh g{sup -1} after 50 cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO{sub 2} nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated that this simple method could be extended for the synthesis of porous metal oxide nanotubes with high performances in the applications of lithium ion batteries ...
2010-10-15
Energy Technology Data Exchange (ETDEWEB)
The overall objective of this research work was to prepare hydrocracking catalysts using amorphous silica-alumina (ASA) supports in combination with USY and {beta}-zeolites. Three supports: namely silica-alumina, USY and {beta}-zeolites were selected to prepare the extrudates using AP-1 as a binder, while two metal pairs: namely Ni-W and Ni-Mo were loaded on the extrudates through co-impregnation using incipient wetness technique. The catalysts were then calcined at 550C for 2h. The catalysts were tested in a fixed-bed flow reaction system for their activity, using desulfurized vacuum gas oil (DS-VGO) as a feedstock. The catalytic evaluation results of the catalysts showed that {beta}-zeolite alone and in combination with the ASA used in this study, has a potential as a support for developing heavy oil hydrocracking catalysts. A balance of weak and strong acidities of {beta}-zeolite provides control cracking, while high surface area and bigger pores of ...
2002-07-10
Composites in the TiC-TiYTZP system
International Nuclear Information System (INIS)
Ceramic matrix composites in the TiC-Ti, Y-TZP system can be synthesized by the reaction between carbon and the TiO_2-Y_2O_3-ZrO_2 solid solution nanopowder. This method results in the more homogeneous powders than those prepared by the physical mixing of TiC and zirconia s.s. powders. Twelve TiO_2-Y_2O_3-ZrO_2 solid solution nanopowders differing in the proportions of the constituent oxides were prepared by the coprecipitation- calcination route. They were reacted with the pyrolytic carbon evenly distributed within the system. Carbon was introduced by the thermal decomposition of the phenol-formaldehyde resin dissolved in ethyl alcohol and mixed with the zirconia s.s. nanopowder. Reaction was performed in vacuum. Compacts of the composite powders sintered in vacuum give dense materials of evenly distributed TiC inclusions of sizes not surpassing 400 nm. Hardness of such materials was dependent on their chemical and phase composition but was generally higher than ...
2003-09-25
Combustion for high temperature heating process
Energy Technology Data Exchange (ETDEWEB)
This paper describes the high-temperature (1500/sup 0/C or higher) heating technology by combusting natural gas. The theoretical adiabatic flame temperature is 1957/sup 0/C at the theoretical air ratio and 2801/sup 0/C at the theoretical oxygen ratio. The flame temperature is increased by 40/sup 0/C every 1%-increase of oxygen up to 25% of the concentration of oxygen and by 28/sup 0/C to 30% of it. The flame temperature is increased by 37 to 38/sup 0/C every 100/sup 0/C-increase of the temperature of preheated air. The practical temperatures are significantly lower than the theoretical ones. The ceramic calciner is provided with a two-stage burner for 1600 to 1800/sup 0/C which can use also the oxygen-riched air. The glass melting furnace is operated at 1500/sup 0/C and the flat flame burner is used for a single kiln. A stabilizing burner is used for reducing the multing time for the steel making electric arc furnace. A high-temperature (1700/sup 0/C) radiant ...
1987-12-05
Characterization of nanosized Tb-MCM-41 synthesized by the sol-gel-assisted self-assembly method
International Nuclear Information System (INIS)
The nanosized luminescent Tb-MCM-41 (1:10) is synthesized by means of sol-gel-assisted self-assembly under basic conditions at room temperature. The results of "2"9Si-MAS NMR and XRD prove that Tb"3"+ doped Si-O framework. The HRTEM image shows that the regular uniform particles with a diameter of 10 nm possess ultralarge pore with diameter 2.0 nm, which is consistent with the result of N_2 adsorption. The BET surface area and porosity of Tb-MCM-41 (1:10) are 1127 m"2/g and 0.84 cm"3/g, respectively. The patterns of selected-area electron diffraction and XRD of Tb-MCM-41 (1:10) show an Fm3m space group in the cubic. FT-IR results show that the peaks near 970 cm"-"1 are assigned to the deformation vibration of silanol group. The as-products are calcined at 800 deg. C and the mesoporous materials possess enormous specific areas and large porosity, it shows that the mesoporous materials are ultrastable.
2003-10-06
Aqueous waste management for minor actinides and lanthanides separation process
Energy Technology Data Exchange (ETDEWEB)
The French strategy of high level radioactive aqueous waste management is an incorporation in glassy fission products containers. Therefore, nitric acid soluble organic reagents needed for minor actinides and lanthanides selective separation from fission product solutions have to be sufficiently removed to reach carbon concentrations compatible with calcinator working. Thus, the ability of reagents to be oxidized under concentration conditions with or without denitration becomes a criteria of selection and have been studied. Further, if not working, other operations like hot hydrogen peroxide oxidation, catalyzed or not, are investigated. Reagents involved in this work are mainly complexing products (N-(2-Hydroxyethyl) Ethylene-diamine-tri-acetic Acid), pH keeping reagents (carboxylic acids like citric, glycolic, tartaric and lactic acid) and alkaline species (Tetramethylammonium hydroxide). Behaviour of acetic acid, which is often the main degradation product, has ...
2004-07-01
British Library Electronic Table of Contents (United Kingdom)
Monodisperse europium-activated titania hollow phosphors had been synthesized by a facile one-pot hydrothermal method using carbon spheres as hard templates. Samples were characterized by X-ray powder diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, energy dispersive spectrometer and photoluminescence spectrum. The strongest emission intensity was observed with TiO2:Eu0.2 hollow spheres and TiO2:Eu0.2 hollow spheres calcining at 550^oC. Moreover, the strongest excitation of TiO2:Eu0.2 hollow spheres transferred from 400 to 500^oC and the effective nonradiative energy transfer from the TiO2 hollow spheres host matrix to Eu^3^+ ions crystal field states was realized due to changes of crystalline field in the environment around Eu^3^+ ions occupying Ti^4^+ site...
2010-01-01
Zeolite-supported Ni and Mo catalysts for hydrotreatments. 2. HRTEM observations
Energy Technology Data Exchange (ETDEWEB)
Calcined and sulfided Ni-Mo catalysts supported on ultrastable Y zeolite (USY), NaY zeolite, mordenite, and ZSM-5 were studied by high-resolution electron transmission microscopy (HRTEM) with selected-area electron diffraction (SAED) and energy-dispersive spectroscopy (EDS). Ni and Mo oxide aggregates were rarely observed in the USY-supported Ni-Mo catalyst, indicating that most of Ni and Mo may be incorporated into USY, e.g., supercavities and possibly sodalite cages. However, there were a large number of {alpha}-NiMoO{sub 4} aggregates of different particle sizes in NaY-, mordenite-, and ZSM-5-supported catalysts, and the mordenite-supported catalyst also contained MoO{sub 3} crystals. The {alpha}-NiMoO{sub 4} may be attached to the surface of substrates as individual particles or needle aggregates, it may be disseminated into mordenite particles, or it may even form an isolated sphere (in Ni-Mo/NaY) or a needle (in Ni-Mo/ZSM-5) aggregates. Thus, most of Ni and ...
2000-01-25
Self-Interacting Dark Matter Halos and the Gravothermal Catastrophe
We study the evolution of an isolated, spherical halo of self-interacting dark matter (SIDM) in the gravothermal fluid formalism. We show that the thermal relaxation time, $t_r$, of a SIDM halo with a central density and velocity dispersion of a typical dwarf galaxy is significantly shorter than its age. We find a self-similar solution for the evolution of a SIDM halo in the limit where the mean free path between collisions, $\\lambda$, is everywhere longer than the gravitational scale height, $H$. Typical halos formed in this long mean free path regime relax to a quasistationary gravothermal density profile characterized by a nearly homogeneous core and a power-law halo where $\\rho \\propto r^{-2.19}$. We solve the more general time-dependent problem and show that the contracting core evolves to sufficiently high density that $\\lambda$ inevitably becomes smaller than $H$ in the innermost region. The core undergoes secular collapse to a ...
2002-01-01
Energy Technology Data Exchange (ETDEWEB)
Proactive qualification is today an integral part of the development process for steam turbines used in steam and combined cycle power plants. By providing experimentally based `random` variables, such as the steam path efficiency and blading reliability, it makes a valuable contribution to the economic `random` variables of the power plant, e.g. the rate of return, as viewed by the customer. One of the areas in which proactive product and process qualification plays an important role is the development of LP steam paths. (orig.) [Deutsch] Die proaktive Qualifikation ist heute fester Bestandteil des Entwicklungsprozesses bei Dampfturbinen, die fuer den Einsatz in Dampf- und Kombikraftwerken bestimmt sind. Sie leistet mit Hilfe experimentell ermittelter `Zufalls`-Variablen, wie z.B. Wirkungsgrad der Fluten und Zuverlaessigkeit der Beschaufelungen, einen wertvollen Beitrag zu den fuer die Kunden wichtigen wirtschaftlichen `Zufalls`-Variablen des ...
1998-10-01
Market-based pricing of wholesale electric services
Energy Technology Data Exchange (ETDEWEB)
Traditionally, the Federal Energy Regulatory Commission has implemented its statutory requirement that wholesale electric rates be just and reasonable by comparing a seller's proposed rates to its own cost of service. In the last four years, 40 requests for market-based prices have opened up an alternate path for just and reasonable rates. The common characteristic of these 40 requests is that the price is not tied directly to the seller's own costs but rather to market conditions. To date, the Commission has approved 28 of these requests and rejected eight. Four are pending. In this paper the authors assess what has happened, and describe the common standards that have been developed on a case-by-case basis in the last four years. In particular, they examine how these standards have been applied in cases involving affiliates of traditional utilities. Finally, they discuss some of the unresolved issues and possible implications of the new ...
1991-12-01
In Internet Routing, the static shortest path (SP) problem has been addressed using well known intelligent optimization techniques like artificial neural networks, genetic algorithms (GAs) and particle swarm optimization. Advancement in wireless communication lead more and more mobile wireless networks, such as mobile networks [mobile ad hoc networks (MANETs)] and wireless sensor networks. Dynamic nature of the network is the main characteristic of MANET. Therefore, the SP routing problem in MANET turns into dynamic optimization problem (DOP). Here the nodes ae made aware of the environmental condition, thereby making it intelligent, which goes as the input for GA. The implementation then uses GAs with immigrants and memory schemes to solve the dynamic SP routing problem (DSPRP) in MANETS. In our paper, once the network topology changes, the optimal solutions in the new environment can be searched using the new immigrants or the useful information stored in the ...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
After a short review of the classical simplified expressions able to evaluate the seepage path in the core of a river levee, this paper first discusses the results obtained assuming the Dupuit approximation. Dimensionless nomographs are then showed, obtained by means of numerical integration of the seepage equations, These nomographs allow a quick levee design to be developed, after the definition of flood hydrography, seepage and embankment characteristics. [Italian] Dopo un sintetico richiamo di alcune classiche formulazioni semplificate per la determinazione dell'andamento della linea di infiltrazioner in un rilevato arginale, nell'articolo vengono presentati e discussi i risultati conseguiti prima assumendo la sola ipotesi di Dupuit e, successivamente, risolvendo l'equazione completa del moto di filtrazione. In particolare, vengono forniti abachi adimensionali che consentono, una volta fissate le caratteristiche ...
1999-10-01
Concrete as secondary containment for interior wall embedded waste lines
International Nuclear Information System (INIS)
Throughout the DOE complex there are numerous facilities that handle hazardous and radioactive waste solutions. Due to the hazardous constituents of the mixed waste, secondary containment of tank systems and their ancillary piping, in accordance with Resource Conservation and Recovery Act, is a concern for such existing facilities. The Idaho Division of Environmental Quality was petitioned in 1990 for an Equivalent Device determination regarding secondary containment of waste lines embedded in interior concrete walls. The petition was granted; however, it expires in 1996. To address the secondary containment issue, additional studies were undertaken. One study verified the hypothesis that an interior wall pipe leak would follow the path of least resistance through the naturally occurring void found below a rigidly supported pipe and pass into an adjacent room where detection could occur, before any significant deterioration of the concrete takes place. Other tests ...
1993-08-17
Calculating electron dose using a convolution/superposition method. 120
International Nuclear Information System (INIS)
The calculation of electronn beam dose using an algorithms similar to convolution/superposition methods for photon beams [1,2,3,4] is explored. The distribution of dose deposited by a number of monoenergetic, point-monodirectional electron pencil beams is first determined using the Monte Carlo method [5,6]. These elementary distributions are combined to model distributions that would result from the spectrum of incident energies and angles [6,7] present in a clinical beam. These modified distributions are then stored for use as kernels in the dose calculation. In the case of a homogeneous phantom, the relative fluence distribution is convolved with the stored kernels to obtain thhe dose distributions in 3 dimensions. Since the kernels cannot be assumed to be spatially invariant in a heterogeneous water-like phantom, the dose deposited on paths from the interaction site to all the dose deposition sites is approximated by scaling the kernels to reflect the average ...
Bern-Kosower rule for scalar QED
International Nuclear Information System (INIS)
We derive a full Bern-Kosower-type rule for scalar QED starting from quantum field theory: we derive a set of rules for calculating S-matrix elements for any processes at any order of the coupling constant. A gauge-invariant set of diagrams in general is first written in the world line path-integral expression. Then we integrate over x(#tau#), and the resulting expression is given in terms of a correlation function on the world line left-angle x(#tau#)x(#tau#"')right-angle. Simple rules to decompose the correlation function into basic elements are obtained. A gauge transformation known as the integration by parts technique can be used to reduce the number of independent terms before integration over proper-time variables. The surface terms can be omitted provided the external scalars are on shell. Also, we clarify correspondence to the conventional Feynman rule, which enabled us to avoid any ambiguity coming from the infinite dimensionality of the ...
Assessment of oil shale technologies
Energy Technology Data Exchange (ETDEWEB)
For many decades, the oil shale resources of the western United States have been considered possible contributors to the Nation's liquid fuel supply. This volume reviews several paths to development of these resources and the likely consequences of following these paths. A chapter providing background information about the nature of oil shale is followed by an evaluation of technologies for recovery of shale oil. The economics and finances of establishing an industry of various sizes are analyzed. The fact that much of the best shale is located on Federal land is examined in light of the desire to increase use of the resources. The consequences of shale development in terms of impact on the physical and social environments, and a discussion of the availability of water complete the report. Policy options addressing barriers that could hinder the establishment of the industry are presented. These options, designed primarily for ...
1980-06-01
Uranium-233 waste definition: Disposal options, safeguards, criticality control, and arms control
Energy Technology Data Exchange (ETDEWEB)
The US investigated the use of {sup 233}U for weapons, reactors, and other purposes from the 1950s into the 1970s. Based on the results of these investigations, it was decided not to use {sup 233}U on a large scale. Most of the {sup 233}U-containing materials were placed in long-term storage. At the end of the cold war, the US initiated, as part of its arms control policies, a disposition program for excess fissile materials. Other programs were accelerated for disposal of radioactive wastes placed in storage during the cold war. Last, potential safety issues were identified related to the storage of some {sup 233}U-containing materials. Because of these changes, significant activities associated with {sup 233}U-containing materials are expected. This report is one of a series of reports to provide the technical bases for future decisions on how to manage this material. A basis for defining when {sup 233}U-containing materials can be managed as waste and when they ...
1998-07-07
Thermal models are constructed and analyses are performed of aluminum-based spent nuclear fuel (Al-SNF) in interim dry storage and geologic disposal configurations. Two models are developed, referred to as the interim storage model and the codisposal waste package (WP) model. Time-dependent source terms of Al-SNF forms and the defense high-level waste (DHLW) canisters are also developed for thermal performance analysis of the geologic codisposal WP.The interim storage model is a three-dimensional conduction-convection conjugate model to investigate the natural convection cooling of a sealed dry storage canister with vertical orientation in a dry storage vault. The analysis is made for various decay heat sources (equivalent to 25 to 35 kW/m{sup 3}) using various boundary conditions around the canister wall and with backfilled nitrogen or helium gas. Based on the data obtained from the Savannah River Site experimental work and available from the literature, an improved dimensionless ...
2000-07-15
The Universal Basic Education Programme and Female Trafficking in South-South, Nigeria
The study investigated the impact of the Universal Basic Education (UBE) programme on the phenomenon of female trafficking in South-South Nigeria. To this end, six research questions were raised. These revolved around: (i) resource situation and adequacy of training provided for repatriated trafficked victims in the service provider centre; (ii) efforts in the formal education sector of the UBE to curb female trafficking; and (iii) parents and female students' disposition toward female trafficking. The design of the study was descriptive survey. The sample was 420 female students and their parents as well as 100 teachers in the formal segment of the UBE programme and 130 repatriated trafficked victims in a service provider centre. Four sets of instruments were utilised to generate data for the study. The first was quantitative designed to elicit information on the resource situation of the service provider centre and the adequacy of the training given to the ...
2007-11-01
Metabolic fate of chlorinated paraffins
Energy Technology Data Exchange (ETDEWEB)
The disposition of three (1-/sup 14/C)-chlorododecanes (MCDD, PCDD I and PCDD II; 17.4%, 55.9%, and 68.5% chlorination) was studied in C57Bl mice. (1-/sup 14/C)-lauric acid (LA) was studied as reference compound. Fifty-two percent (MCDD), 32% (PCDD I), and 8% (PCDD II) of the radioactive doses were exhaled as /sup 14/CO/sub 2/ during 12 h after i.v. injection. Similar results were obtained after p.o. administration. In addition to a marked labelling of the liver and fat, the distribution patterns observed at 24 h after administration revealed an uptake of radioactivity in tissues with high cell turnover/high metabolic activity, e.g., intestinal mucosa, bone marrow, salivary glands and thymus. The concentration of radioactivity in these sites and the exhalation of /sup 14/CO/sub 2/, which were inverse to the degree of chlorination, indicate that the chloroalkanes are degraded to metabolites which can be utilized in the intermediary metabolism. A similar, although ...
1982-09-01
Energy Technology Data Exchange (ETDEWEB)
The detailed sequence stratigraphic analysis of the siliciclastic-dominated Late Cretaceous sediments (Aren Sandstone and Garumnian red beds, south central Pyrenees, Spain) reveals the repeating disposition of critical elements and controlling mechanisms of cycles and sequences. Our approach integrates (a) hierarchy of unconformity-bounded units, (b) physical expression of boundaries traceable from the continent to the basin, (c) featuring facies and depositional systems, (d) well log and seismic expression, and (e) driving basing-filling mechanisms. A comparison to other active basins is suggested in order to prove the validity beyond the regional scale. Four basin-wide transgressive facies cycles were identified and interpreted as third-order units. The transgressive phase of each cycle is represented by mixed shelf deposits, while regressive periods consists of complex delta systems. The cycles are composed within their regressive phase of fourth-order ...
1993-09-01
Energy Technology Data Exchange (ETDEWEB)
The Materials & Fuel Complex (MFC) facilities 799 Sodium Processing Facility (a single building consisting of two areas: the Sodium Process Area (SPA) and the Carbonate Process Area (CPA), 799A Caustic Storage Area, and 770C Nuclear Calibration Laboratory have been declared excess to future Department of Energy mission requirements. Transfer of these facilities from Nuclear Energy to Environmental Management, and an associated schedule for doing so, have been agreed upon by the two offices. The prerequisites for this transfer to occur are the removal of nonexcess materials and chemical inventory, deinventory of the calibration source in MFC-770C, and the rerouting and/or isolation of utility and service systems. This report provides a description of the current physical condition and any hazards (material, chemical, nuclear or occupational) that may be associated with past operations of these facilities. This information will document conditions at time of transfer of the ...
2009-11-01
Fabrication of zircon for disposition of weapons plutonium
International Nuclear Information System (INIS)
This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). In an effort to address the problems of long term storage and nuclear waste minimization, zircon has been proposed as a host medium for plutonium and other actinides recovered from dismantled nuclear weapons. The objective of this work is to investigate the feasibility of large scale fabrication of Pu-bearing zircon. Since PuO_2 is thermodynamically less stable than ZrO_2, it is expected that the process parameters determined for synthesizing ZrSiO_4 (zircon) would be applicable to those for PuSiO_4 (Pu-zircon). Furthermore, since the foremost concern in plutonium processing is the potential for contamination release, this work emphasizes the development of process parameters, using zircon first, to anticipate potential material problems in the containment system for reaction mixtures during processing. Stoichiometric mixtures of ZrO_2 and ...
FY 1986 current fiscal year work plan
Energy Technology Data Exchange (ETDEWEB)
This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office/RI during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing ...
1985-11-01
Defense Waste and Environmental Restoration Program Plan: Defense Waste Management Division
Energy Technology Data Exchange (ETDEWEB)
The DEFENSE WASTE MANAGEMENT PROGRAM has been chartered by the Department of Energy (DOE) to receive, reduce, store, and maintain all radioactive defense waste generated by Hanford and received from offsite DOE contractors in a safe condition and in accordance with DOE and Westinghouse Hanford Company (WHC) standards. These activities are accomplished through the use of TRU retrievable storage sites, solid waste burial grounds, liquid waste storage tanks, capsule storage pools, and other low-level waste disposal methods. Continuous and/or periodic surveillance is maintained. Through the use of improved packaging methods, evaporator-crystallization and capsule production waste has been and continues to be put in a safe and economic storage condition pending future reprocessing or final disposition. For this Program Plan, the scope of Defense Waste Management programmatic activities has been organized into three general categories. A summary outline of the work ...
1988-09-01
Energy Technology Data Exchange (ETDEWEB)
This additional protocol to the agreement between France, EURATOM and the IAEA aims at reinforcing the nuclear weapons non-proliferation regime. This protocol widens the field of competences of the IAEA with the supply of new information relative to: the civil nuclear cooperation between France and countries having no nuclear weapons in the domain of fuel cycle; the regular inspection of French nuclear facilities; the trade (import and export) of medium- or high-level radioactive wastes containing plutonium, highly enriched uranium or {sup 233}U, and the trade of some non-nuclear equipments or materials with countries having no nuclear weapons. The protocol defines also some practical dispositions relative to the delays and periodicity of controls, to the transmission of data, to the appointment of IAEA inspectors and their access to the facilities and sites considered. The list of the activities and equipments covered by the protocol are given in appendixes. ...
2002-07-01
Energy Technology Data Exchange (ETDEWEB)
At Los Alamos National Laboratory (LANL), a recent effort in waste minimization has focused on scrap metal from radiological controlled areas (RCAs). In particular, scrap metal from RCAs needs to be dispositioned in a reasonable and cost effective manner. Recycling of DOE scrap metals from RCAs is currently under a self-imposed moratorium. Since recycling is not available and reuse is difficult, often metal waste from RCAs, which could otherwise be recycled, is disposed of as low-level waste. Estimates at LANL put the cost of low-level waste disposal at $550 to $4000 per cubic meter, depending on the type of waste and the disposal site. If the waste is mixed, the cost for treatment and disposal can be as high as $50,000 per cubic meter. Disposal of scrap metal as low-level waste uses up valuable space in the low-level waste disposal areas and requires transportation to the disposal site under Department of Transportation (DOT) regulations for low-level waste. In ...
2002-01-01
Vegetation re-establishment on a hardwood forest site denuded by brine
Energy Technology Data Exchange (ETDEWEB)
Brine from active oil wells seeped through the soil of a forested site in north-western Pennsylvania and killed all vegetation in its path, leaving the affected area unproductive and unsightly. After the brine source was eliminated, herbaceous plants, shrubs and forest tree seedlings became established and developed rapidly. Establishment began in the first year and by Year 4 the site had developed into a healthy young forest. Results show that Allegheny hardwood forest sites damaged by brine water will rapidly revegetate once the brine water discharge is stopped if there is a seed supply and if the area is fenced to exclude deer. 3 figs., 12 refs.
1989-04-01
Tissue banking for research: connecting the disconnected
British Library Electronic Table of Contents (United Kingdom)
Delivering the promise of personalised medicine is the challenge that the current generation of scientists face. The variations in human physiology and disease are considerable, and designing appropriate strategies to deliver what has been promised will require access to tissue from a large number of volunteers. The NHS provides an ideal infrastructure for sample acquisition, but requires two things to make this available?public consent and support for extra manpower and administration. There is a disconnection between the NHS and tissue based research that needs to be addressed on a number of levels to provide a translational platform. This should enable the path to be beaten to provide the ideal tailored treatment for future patients; one that preserves quality of life by curing the dise...
2011-01-01
Three-frame Algorithm of Car Path Reconstruction from Airborne Traffic Data
The airborne traffic monitoring system forms a novel technology of detecting vehicle motion. An optical digital camera located on an airborne platform produces a series of images which then are processed to recognized the fixed vehicles. In this way the video data are converted into the time sequence of frames containing the vehicle coordinates. In the present work a three-frame algorithm is developed to identify the succeeding vehicle positions. It is based on finding the neighboring points in the frame sequence characterized by minimal acceleration. To verify and optimize the developed algorithm a ``Virtual Road'' simulator was created. Finally available empirical data are analyzed using the created algorithm.
2007-01-01
Temperature Dependences of Leakage Currents of ZnO Varistors Doped with Rare-Earth Oxides
British Library Electronic Table of Contents (United Kingdom)
Rare-earth oxides are doped into ZnO varistors as grain growth inhibitors for increasing the varistors' voltage gradients. However, their leakage currents become large and their nonlinear coefficients decrease at the same time. The reasonable explanation for such a phenomenon has not yet been available. In this paper, the temperature dependences of varistor samples' leakage currents are investigated, which reveal that the increased leakage currents of ZnO varistors with Y2O3 doping are mainly due to the bypass paths through the intergranular materials at grain corners.
2010-01-01
Spinodal decomposition and giant magnetoresistance
International Nuclear Information System (INIS)
We explore the relation of nanostructures with the appearance of giant magnetoresistance (GMR) in melt-spun CuCo ribbons. We find by energy-filtered transmission electron microscopy that the ribbons are composed of a periodic distribution of Co within the Cu, as in spinodal decomposition. The lamellar structure should thus be associated with GMR, as only a small percentage of the Co is present in the form of grains. This is counterintuitive, for no clear interfaces are present as required by standard models, and the period of the composition oscillation (43-52 nm) is an order of magnitude larger than the mean free paths for electrons. Upon annealing, a secondary spinodal decomposition appears following the same direction as the original.
2006-10-01
Simple model for characterizing the electrical resistivity in A-15 superconductors
A discussion of some of the difficulties with previous analyses of the resistivity of A-15 compounds is given. Precise high-temperature data on ..cap alpha..-particle- and electron-damaged Nb/sub 3/Ge and Nb/sub 3/Sn samples with different defect concentrations are presented here and analyzed in a simple way with use of a phenomenological model based on the idea that the ideal resistivity must approach some limiting value in the regime where the mean free path becomes comparable to the interatomic spacing.
1977-04-04
Sharp regularity for certain nilpotent group actions on the interval
According to the classical Plante-Thurston Theorem, all nilpotent groups of $C^2$-diffeomorphisms of the closed interval are Abelian. Using techniques coming from the works of Denjoy and Pixton, Farb and Franks constructed a faithful action by $C^1$-diffeomorphisms of $[0,1]$ for every finitely-generated, torsion-free, non-Abelian nilpotent group. In this work, we give a version of this construction that is sharp in what concerns the H\\"older regularity of the derivatives. Half of the proof relies on results on random paths on Heisenberg-like groups that are interesting by themselves.
2011-01-01
Selected topics in transient response of aerial lines to high-altitude electromagnetic pulse
International Nuclear Information System (INIS)
Aerial lines or cables, as one mainly energy transport path of electronic system when illuminated by HEMP, has been often modeled by field-to-transmission line model. However, in many cases, authors too often encounter some confusing statements to the lines effects during experimental procedure. The aim of this paper is to present and discuss these cases, such as the electromagnetic environment above the ground plane, the contribution of the different electromagnetic field component to the induced current and voltage, variations of the load current for different line heights and ground conductivities etc. (authors)
2005-11-01
Energy Technology Data Exchange (ETDEWEB)
A rocket borne experiment to measure the temperature structure of the inner solar corona via the doppler broadening of the resonance hydrogen Lyman-..cap alpha.. (lambda1216A) radiation scattered by ambient neutral hydrogen atoms was attempted during the 16 Feb 1980 solar eclipse. Two Nike-Black Brant V sounding rockets carrying instrumented payloads were launched into the path of the advancing eclipse umbra from the San Marco satellite launch platform 3 miles off the east coast of Kenya.
1981-01-01
Energy Technology Data Exchange (ETDEWEB)
Over the last year, the energy industry firmly established itself as the premier borrowing sector in the international financial markets. While Europe and North America's major energy companies continue to access the loan market as their main source of financing, with a steady flow of new international borrowings, their peers from other areas of the world, such as Latin America and the Middle East, are in the process of positioning themselves in the market as regular borrowers and have become an important new source of fee income for industry's bankers. (Author).
1992-06-01
Protective oxides in coal-fired combined cycle power systems
Energy Technology Data Exchange (ETDEWEB)
In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.
1995-12-31
Principle, classification and functions of geochemical modeling codes
International Nuclear Information System (INIS)
Geochemical model is a kind of concept model which describes geochemical processes by means of chemical reaction equations and mathematical formula, and the software based on the concept model are called geochemical modeling code. Geochemical modeling codes can be divided into three categories: mass equilibrium, mass transfer and mass transport code. The major functions of geochemical codes include the calculation of forms of occurrence of elements, the prediction of direction of various geochemical reaction, the dissolution and precipitation of elements, the pH and Eh value, the rate and path of geochemical reaction in aqueous solution.
Power systems for space exploration
Energy Technology Data Exchange (ETDEWEB)
The Outreach Program was designed to solicit creative ideas from academia, research institutions, private enterprises, and the general public and is intended to be helpful in defining promising technical areas and program paths for more detailed study. To the Outreach Program, a number of power system concepts were proposed. In conclusion, there are a number of advanced concepts for space power and propulsion sources that deserve study if we want to expand our ability to not only explore space, but to utilize it. Advanced nuclear concepts and power beaming concepts are two areas worthy of detailed assessments.
1992-01-01
Oman: current status, upstream and export developments, investment opportunities
Energy Technology Data Exchange (ETDEWEB)
Oman is an attractive and welcoming country, well-ordered and unpretentious. It has benefited from remarkable achievements of economic and social development since 1970. It now has a resource base that should be sufficient to keep it on continuing path of further development. However, the second 20-years of modern Oman will inevitable contain some testing challenges. These are centred in two main areas - the economic, where expenditure has already outstripped revenue and where firm controls are needed to maintain a reasonable balance; and the social, where the pressures from an increasingly literate and numerous population will demand changes to the autocratic traditional system of government. (author)
1995-11-01
Non-Abelian duality, parafermions, and supersymmetry
Energy Technology Data Exchange (ETDEWEB)
Non-Abelian duality in relation to supersymmetry is examined. When the action of the isometry group on the complex structures is nontrivial, extended supersymmetry is realized nonlocally after duality, using path-ordered Wilson lines. Prototype examples considered in detail are, hyper-Kahler metrics with SO(3) isometry and supersymmetric WZW models. For the latter, the natural objects in the nonlocal realizations of supersymmetry arising after duality are the classical non-Abelian parafermions. The canonical equivalence of WZW models and their non-Abelian duals with respect to a vector subgroup is also established. {copyright} {ital 1996 The American Physical Society.}
1996-07-01
Multigrid Particle-in-cell Simulations of Plasma Microturbulence
Energy Technology Data Exchange (ETDEWEB)
A new scheme to accurately retain kinetic electron effects in particle-in-cell (PIC) simulations for the case of electrostatic drift waves is presented. The splitting scheme, which is based on exact separation between adiabatic and on adiabatic electron responses, is shown to yield more accurate linear growth rates than the standard df scheme. The linear and nonlinear elliptic problems that arise in the splitting scheme are solved using a multi-grid solver. The multi-grid particle-in-cell approach offers an attractive path, both from the physics and numerical points of view, to simulate kinetic electron dynamics in global toroidal plasmas.
2003-06-17
Medium carbon vanadium micro alloyed steels for drop forging
International Nuclear Information System (INIS)
Growing competitiveness of alternative manufacturing routes requires cost minimization in the production of drop forged components. The authors analyse the potential of medium carbon, vanadium microalloyed steels for drop forging. Laboratory and industrial experiments have been carried out emphasizing deformation and temperature cycles, strain rates and dwell times showing a typical processing path, associated mechanical properties and corresponding microstructures. The steels the required levels of mechanical properties on cooling after forging, eliminating subsequent heat treatment. The machinability of V-microalloyed steels is also improved when compared with plain medium carbon steels. (author)
Mechanisms of Alloy 800 corrosion in helium
International Nuclear Information System (INIS)
Cr_2O_3 scales are found to form on Alloy 800 and a similar pure ternary alloy in air, and 1 and 50 atm. helium containing oxidizing impurities typical of those in an SGHTR. The strong temperature dependence and neglibible helium overpressure dependence indicate that gas transport through the scales is not rate controlling. Surface oxidation rates are therefore controlled by solid state diffusion and the low oxygen partial pressure dependence of the oxidation rate in Alloy 800 is ascribed to the presence of extrinsic defects in the Cr_3O_3 (due to doping by alloying elements) or to the presence of short circuit diffusion paths. (Auth.).
Interferometry and refraction measurements in plasmas of elliptical cross-section
Energy Technology Data Exchange (ETDEWEB)
The measurement of electron densities using interferometry and refraction measurements in plasmas with cross-sections where the electron density contours are concentric ellipses is examined. Transforms are found for both interferometrically deduced optical path-length differences and refraction angle data obtained from elliptical cross-section plasmas. The transformed data can be inverted to give electron densities using standard techniques developed for circular cross-section plasmas. Refraction of light in elliptical cross-section plasmas is examined using numerical ray tracing.
1984-04-14
Hot-air turbine plant at Voelklingen model power plant
Energy Technology Data Exchange (ETDEWEB)
The integration of a gas turbine into a new type of coal-fired combined cycle power plant necessitates a multiplicity of far-reaching changes compared with a normal design. The extremely high pre-heating temperature of the air emanating from the heat exchanger of the fluidized bed for the gas turbine combustion chamber has necessitated extensive development work and associated combustion trials. It was possible for these results to influence the design of the burners whereas the manufacture of other components which was on the critical path was already far advanced.
1984-06-01
Home shrines in Britain and associated spiritual values
British Library Electronic Table of Contents (United Kingdom)
In a quantitative survey of religious attitudes and practices in a multi-religious sample of 369 school pupils aged between 13 and 15 in London, the presence of a home shrine was found widespread in 11% of adolescents spanning several religious affiliations and ethnicities - especially Buddhists, Hindus and those of Indian, Chinese and 'Other Asian' ethnicity. Having a home shrine correlated significantly with spiritual attitudes such as agreement with filial piety, the Eightfold Path, subjectivity of happiness, meditation, Sikh festivals, reincarnation and opening Gurdwaras to all. It is suggested that teachers and the social services should be aware of the importance of shrines to many religious communities and recognise their potential as a spiritual asset and manifestation of religion ...
2010-01-01
Gamma-gamma collider based on Compton back-scattering
International Nuclear Information System (INIS)
A #gamma##gamma# collider would extend and complement the physics capability of a linear collider; e.g. it would be suitable for direct measurement of the partial decay width of a Higgs boson into two gamma quanta. This paper discusses choice of laser parameters, luminosity optimization, electron and laser parameters for a gamma- gamma collider as a second interaction region for the Next Linear Collider, laser path, and the lasers. It is concluded that a gamma- gamma collider is technically feasible; however it will require a significant investment in preparatory R ampersand D.
1996-08-25
Energy Technology Data Exchange (ETDEWEB)
This article outlines the use of gasifiers during World War II and how, with soaring fuel prices, producer gas may provide an alternate energy path for agribusiness and farms today. In the last few years, the University of California has become a focus of producer gas research in the US. Biomass fuels used include crushed walnut shells, fruit pits, cereal straw and corn cobs. Particle size, moisture content and slagging create problems and the right kind of gas producer must be used to obtain reliable conversion to producer gas.
1980-09-08
Feynman integral treatment of the Bargmann potential
International Nuclear Information System (INIS)
A method based on path integral formulation is given for obtaining exact solution of the s states for the Bargmann potentialV(r)=1ka"2#beta#(#beta#-1)e"-"2"r"/"a1-e"-"r"/"a"2-Ae"-"r"/"a1-e"-"r"/"a,where #beta# and k are parameters. The exact energy spectrum and the normalised s-state eigenfunctions are obtained from the poles of the Green function and their residues, respectively. The results are compared with their of Schrodinger formalism, special cases are also discussed.
2005-06-01
Failure analysis on a ruptured petrochemical pipe
Energy Technology Data Exchange (ETDEWEB)
The failure took place on a welded elbow pipe which exhibited a catastrophic transverse rupture. The failure was located on the welding HAZ region, parallel to the welding path. Branching cracks were detected at the edge of the rupture area. Deposits of corrosion products were also spotted. The optical microscope analysis showed the presence of transgranular failures which were related to the stress corrosion cracking (SCC) and were predominantly caused by the welding residual stress. The significant difference in hardness between the welded area and the pipe confirmed the findings. Moreover, the failure was also caused by the low Mo content in the stainless steel pipe which was detected by means of spark emission spectrometer. (orig.)
2010-08-15
Electromagnetic characterization of superconducting radio-frequency cavities for gw detection
International Nuclear Information System (INIS)
The electromagnetic properties of a prototype gravitational wave detector, based on two coupled superconducting microwave cavities, were tested. The radio-frequency (rf) detection system was carefully analysed. With the use of piezoelectric crystals small harmonic displacements of the cavity walls were induced and the parametric conversion of the electromagnetic field inside the cavities explored. Experimental results of bandwidth and sensitivity of the parametric converter versus stored energy and voltage applied to the piezoelectric crystal are reported. A rf control loop, developed to stabilize phase changes on signal paths, gave a 125 dBc rejection of the drive mode on a time scale of 1 h.
2004-03-07
Different paths: gender, immigration and political participation.
"Building on arguments made by Grasmuck and Pessar (1991), Hardy-Fanta (1993), and Hondagneu-Sotelo (1994), among others, this article makes the case for a gendered understanding of immigrant political socialization. Looking at recent Latin American immigrants to New York City, the article argues that immigrant Latino men are more likely to favor continuity in patterns of socialization and organization, and immigrant Latinas are more likely to favor change. This finding helps bridge theoretical and empirical literatures in immigration studies, applying the logic of gender-differentiated decisionmaking to the area of immigrant political socialization and behavior." PMID:12293595
1998-01-01
CyberKnife SRS: new technologies that enhance the treatment of cancer
International Nuclear Information System (INIS)
The CyberKnife Robotic Radiosurgery System (Accuracy Incorporated, Sunnyvale, CA, USA) is used worldwide to treat tumors and neurological disorders anywhere in the body with sub-millimetre beam delivery accuracy. Accuracy has developed a number of new technologies in recent years to enhance the treatment of cancer patients. Such new technologies include a fast Monte Carlo Dose Calculation algorithm, Sequential Optimization dose planning, the IrisTM Variable Aperture Collimator, an 800 MU/min Linear Accelerator, and Optimized Path Traversal. These technologies enable physicists and physicians to plan treatments quickly and easily and deliver them with unrivalled accuracy and precision
2008-11-26
Energy Technology Data Exchange (ETDEWEB)
This paper describes a novel Fourier transform infrared (FTIR) spectroscopic method that can be used to rapidly screen soil samples from potentially hazardous waste sites. Samples are heated in a thermal desorption unit and the resultant vapors are collected and analyzed in a long-path gas cell mounted in a FTIR. Laboratory analysis of a soil sample by FTIR takes approximately 10 minutes. This method has been developed to identify and quantify microgram concentrations of explosives in soil samples and is directly applicable to the detection of selected volatile organics, semivolatile organics, and pesticides.
1995-06-01
Grid-Search Location Methods for Ground-Truth Collection from Local and Regional Seismic Networks
Energy Technology Data Exchange (ETDEWEB)
The objective of this project is to develop improved seismic event location techniques that can be used to generate more and better quality reference events using data from local and regional seismic networks. Their approach is to extend existing methods of multiple-event location with more general models of the errors affecting seismic arrival time data, including picking errors and errors in model-based travel-times (path corrections). Toward this end, they are integrating a grid-search based algorithm for multiple-event location (GMEL) with a new parameterization of travel-time corrections and new kriging method for estimating the correction parameters from observed travel-time residuals. Like several other multiple-event location algorithms, GMEL currently assumes event-independent path corrections and is thus restricted to small event clusters. The new parameterization assumes that travel-time corrections are a function of both the event ...
2003-07-24
Diverter/bop system and method for a bottom supported offshore drilling rig
Energy Technology Data Exchange (ETDEWEB)
A system is described adapted for alternative use as a diverter or a blowout preventer for a bottom supported drilling rig and adapted for connection to a permanent housing attached to rig structural members beneath a drilling rig rotary table, the permanent housing having an outlet connectable to a rig fluid system flow line. The system consists of: a fluid flow controller having a controller housing with a lower cylindrical opening and an upper cylindrical opening and a vertical path therebetween and a first outlet passage and a second outlet passage provided in its wall, a packing element disposed within the controller housing, and annular piston means adapted for moving from a first position to a second position, whereby in the first position the piston means wall prevents interior fluid from communicating with the outlet passages in the controller housing wall and in the second position the piston means wall allows fluid communication of interior fluid with ...
1986-07-01
Analysis of log rate noise in Ontario's CANDU reactors
Energy Technology Data Exchange (ETDEWEB)
In the fall of 2003, the operators noticed that in the recently-refurbished Bruce A Shutdown System no. 1 (SDS1) the noise level in Log Rate signals were much larger than before. At the request of the Canadian Nuclear Safety Commission (CNSC), all Canadian CANDU reactors took action to characterize their Log Rate noise. Staff of the Inspection and Maintenance Services division of Ontario Power Generation (OPG) has collected high-speed high-accuracy noise data from nearly all 16 Ontario reactors, either as part of routine measurements before planned outages or as a dedicated noise recording. This paper gives the results of examining a suitable subset of this data, with respect to the characteristics and possible causes of Log Rate noise. The reactor and instrumentation design is different at each station: the locations of the moderator injection nozzles, the location of the ion chambers for each system, and the design of the Log Rate amplifiers. It was found that the Log noise (source ...
2007-07-01
Fate of Mercury in Synthetic Gypsum Used for Wallboard Production
Energy Technology Data Exchange (ETDEWEB)
This report presents and discusses results from Task 5 of the study ''Fate of Mercury in Synthetic Gypsum Used for Wallboard Production,'' performed at a full-scale commercial wallboard plant. Synthetic gypsum produced by wet flue gas desulfurization (FGD) systems on coal-fired power plants is commonly used in the manufacture of wallboard. The FGD process is used to control the sulfur dioxide emissions which would result in acid rain if not controlled. This practice has long benefited the environment by recycling the FGD gypsum byproduct, which is becoming available in increasing quantities, decreasing the need to landfill this material, and increasing the sustainable design of the wallboard product. However, new concerns have arisen as recent mercury control strategies developed for power plants involve the capture of mercury in FGD systems. The objective of this study is to determine whether any mercury is released into the atmosphere when the ...
2006-06-01
Energy Technology Data Exchange (ETDEWEB)
Aqueous solutions of Al/sub 2/(SO/sub 4/)/sub 3/ (1.05 g/100 ml), AlCl/sub 3/ (0.82 g/100 ml) and Ca(OH)/sub 2/ slurry (0.94 g/50 ml) were mixed in various volume ratios and passed through a filter. White cakes left on the filter consisted mainly of ettringite (6CaO.Al/sub 2/O/sub 3/.3SO/sub 3/.32H/sub 2/O). The cakes were then calcined at various temperatures of 300/sup 0/ -- 1000/sup 0/C for 30 and 60 min and pulverized to 80 -- 200 mesh powders. The adsorption capacity of the powders for U(VI) ions dissolved in aqueous solutions was determined by immersing 0.100 g of their powders in 50 ml of the aqueous solution containing 100 ppm of U(VI) ions mainly in the form of (UO/sub 2/(CO/sub 3/)/sub 3/)/sup 4 -/ for 2 hours. The results obtained were summarized as follows. 1) Among the powders prepared, those of the oxide compositions, 2.9CaO.Al/sub 2/O/sub 3/.1.4SO/sub 3/ and 2.5CaO.Al/sub 2/O/sub 3/.1.2SO/sub 3/, all fired at 500/sup 0/C or 600/sup 0/C showed high ...
1981-11-01
Energy Technology Data Exchange (ETDEWEB)
Nano-particles of CeO{sub 2} with the smallest average particle size (18.7 nm) and spherical morphology were obtained from a mixture solution of Ce(NO{sub 3}){sub 3}{center_dot}6H{sub 2}O, citric acid, polyvinyl alcohol by an auto-combustion process exploiting sol-gel as precursors. The course of size control and shape control by polyvinyl alcohol was examined in detail. A transmission electron microscopy (TEM) and an atomic force microscopy (AFM) were employed to characterize the particle-size and morphology of CeO{sub 2} particles. In addition, a sort of nano-metric solid acid SO{sub 4}{sup 2-}/CeO{sub 2} based on CeO{sub 2} nano-particles was prepared by macerating, filtering, drying and calcining processes. The particle-size of SO{sub 4}{sup 2-}/CeO{sub 2} was also assessed by TEM. The composition of SO{sub 4}{sup 2-}/CeO{sub 2} was analyzed by X-ray diffraction (XRD) and infrared spectra (IR). The influencing factors in the formation of SO{sub 4}{sup ...
2003-12-20
Preparation of vanadium III oxidic compounds, and dehydrogenation of paraffins
Energy Technology Data Exchange (ETDEWEB)
A process is described for making a compound selected from a crystalline spinel of the formula A/sup II/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/ formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/ formula (2) from a pentavalent vanadium compound, where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is one ore more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to <2, and y is zero to<1. The process comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup III/ state by heating at 100/sup 0/C. or less an aqueous medium slurry or solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium either before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in solution in the ratio called for by the selected formula, (3) removing ...
1988-04-12
Preparation of vanadium III oxidic compounds and dehydrogenation of paraffins
Energy Technology Data Exchange (ETDEWEB)
This patent describes the vapor phase catalytic dehydrogenation of a C/sub 2/-C/sub 4/ paraffin by contacting the paraffin with a spinel of the formula A/sup III/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/, formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/, formula (2) where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is oone of more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to < 1.9, and y is zero to < 0.9, which spinel or perovskite is made by a process which comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup 111/ state by heating at 100/sup 0/C or less an aqueous medium slurry of solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium ether before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in ...
1988-08-09
How does sorbent particle structure influence sulfur capture under PFBC conditions?
Energy Technology Data Exchange (ETDEWEB)
The physical structure of a limestone or dolomite to be used in in-bed sulfur capture in fluidized bed boilers has great impact on the efficiency of sulfur capture and sorbent use. Therefore in process optimization and model calculations parameters describing the pore structure of these sorbents must be included. In this study an unreacted shrinking core model with variable effective diffusivity is applied to sulfation test data from a pressurized thermogravimetric apparatus (P-TGA) for various limestone and dolomite samples. The particle size was 250--300 {micro}m for all sorbents. The tests were done under typical conditions for a pressurized fluidized bed combustor, i.e. 850 C or 950 C, 15 bar, and were reported earlier at the 12th International Conference on Fluidized Bed Combustion. At these conditions the limestone remains uncalcined, while the dolomite is half-calcined. The sorbents were characterized by chemical composition analysis, particle density ...
1995-12-31
Final report on process modeling of cupola furnaces
This report describes the first phase of the AFS/DOE program on mathematical modeling of cupola behavior, covering the period May 19, 1989 to July 19, 1990. The objective of the program is to develop a comprehensive mathematical model of the cupola furnace for on-line and off-line process control and optimization. The work is being carried out by five organizations: Massachusetts Institute of Technology with responsibility for heat transfer and fluid flow modeling, and incorporation of the chemical models being developed by the University of Michigan team. Modern Equipment Company has the responsibility of compiling information on needed sensors for monitoring operation and providing materials data to be used for cupola input. General Motors, Central Foundry Division, is investigating the potential to augment the mathematical models with artificial intelligence programs. Lastly, General Motors Research laboratories are charged with providing accurate cupola operational data to test the ...
1990-07-01
Dielectric dispersion study of Mn-doped PLZT (8/65/35)
International Nuclear Information System (INIS)
Mn-modified Pb0.92La0.08(Zr0.65Ti0.35)O3 (PLZT) was prepared chemically by a coprecipitate method using their respective nitrate salts and isopropoxides. Differential thermal analysis (DTA) and X-ray analysis clearly show the formation of PLZT single rhombohedral phase for samples calcined beyond 750 C. Uniform grain distribution was observed from scanning electron microscopic (SEM) studies and grain size was found to increase with Mn doping up to x=0.08 and then decreased. Dielectric measurement shows the decrease in peak transition temperature (TC) with Mn doping up to x=0.12 and then increase along with a sharp rise in dielectric maxima. A diffuse dielectric dispersion is observed in all the compositions. A detailed dispersion study was carried out using the Vogel-Fulcher empirical relation, a universal relaxation law and the Havriliak-Negami function. The Vogel-Fulcher relation fitting parameters of activation energy and freezing temperature were found to ...
2009-07-01
CHEMICAL TECHNOLOGY DIVISION, UNIT OPERATIONS SECTION MONTHLY PROGRESS REPORT, JULY 1960
A critical review of the literature revealed no experiments on uranyl ion transfer from an aqueous to a tributyl phosphate phase which positively measured the kinetics of the chemical reaction at the interphase. Drawing isorhythmic lines on a three component diagram gives a complex correlation for the compaction of three sizes of glass beads. Neither the use of thoria sols nor high feed solution concentrations of thorium nitrate gave any significant increase in mean particle diameters over those obtained from nitrate solutions of lower concentrations in flame denitration. A hydraulic film resistance has been detected in the anion exchange of uranyl sulfate into Dowex 2lK, and chloride elution was found to give a higher apparent uranium diffusion coefficient than nitrate elution. The rate of dissolution of mixed thorium-uranium oxides was determined as a function of the per cent of mixed oxides dissolved. Mixing in tanks packed with boron glass Raschig rings ...
1960-10-27
CERAMIC MEMBRANES FOR HYDROGEN PRODUCTION FROM COAL
Energy Technology Data Exchange (ETDEWEB)
The preparation and performance of membranes for application to hydrogen separation from coal-derived gas is described. The membrane material investigated was dense amorphous silica deposited on a suitable support by chemical vapor deposition (CVD). Two types of support materials were pursued. One type consisted of a two-layer composite, zeolite silicalite/{alpha}-Al{sub 2}O{sub 3}, in the form of tubes approximately 0.7 cm in diameter. The other type was porous glass tubes of diameter below 0.2 cm. The first type of support was prepared starting from {alpha}-Al{sub 2}O{sub 3} tubes of 1{micro}m mean pore diameter and growing by hydrothermal reaction a zeolite silicalite layer inside the pores of the alumina at the OD side. After calcination to remove the organic template used in the hydrothermal reaction, CVD was carried out to deposit the final silica layer. CVD was carried out by alternating exposure of the surface with silicon tetrachloride and water vapor. SEM ...
2004-04-01
Energy Technology Data Exchange (ETDEWEB)
The integrity of the RPV head and reactor internals was assessed by means of fluid-structural analyses using a coupled method to evaluate the water hammer phenomenon arising from high burnup fuel failure under RIA conditions. The fluid viscosity effect on the water column burst as well as the complex three-dimensional flow paths caused by a core shroud and standpipes were considered in this study. The three analysis scenarios were designed to investigate the above mentioned influential factors separately. In the first scenario, a two-dimensional axisymmetric reactor vessel model without any reactor internals was modeled to assess the influence of the fluid dynamics in the NSC RIA regulatory evaluation. This model has an actual RPV geometry and can be simply separated from other influential factors in order to concentrate only on investigation of the fluid viscosity effect. In the second scenario, a two-dimensional axisymmetric reactor vessel model with major ...
2003-07-01
British Library Electronic Table of Contents (United Kingdom)
The transport of liquid water and gaseous reactants through a gas diffusion layer (GDL) is one of the most important water management issues in a proton exchange membrane fuel cell (PEMFC). In this work, the liquid water breakthrough dynamics, characterized by the capillary pressure and water saturation, across GDLs with and without a microporous layer (MPL) are studied in an ex-situ setup which closely simulates a real fuel cell configuration and operating conditions. The results reveal that recurrent breakthroughs are observed for all of the GDL samples tested, indicating the presence of an intermittent water drainage mechanism in the GDL. This is accounted for by the breakdown and redevelopment of the continuous water paths during water drainage as demonstrated by Haines jumps. For GDL ...
2010-01-01
Third generation nuclear new builds: Opportunities and challenges
International Nuclear Information System (INIS)
Full text: The nuclear renaissance, anticipated by AREVA in the beginning of the century is now happening in several countries around the world. The fundamentals being the increasing demand of energy, the volatility of fossil fuel prices, the awareness of climate change threat connected with the extensive use of fossil fuels. The EPRTM reactor present significant improvements compared to previous generation reactors enabling to reach an outstanding safety level (redundancy of safety systems, airplane crash resistance), to improve the economics (extended plant lifetime, flexibility and availability during operation and, increased efficiency and fuel utilization) while limiting the impact on workers and the environment. Several countries have been implementing the transition to third generation reactors. The presentation will analyze different examples in order to draw the lessons learned from this first wave and to set-up the criteria for a successful transition ...
2009-10-12
Thermal control of electric vehicle batteries
Energy Technology Data Exchange (ETDEWEB)
The need to operate electric vehicles in warm, summer conditions and also provide for long periods of standby in cold climates is a challenging problem for any battery system. All advanced batteries of high specific energy require active cooling systems because adiabatic heating will raise the temperature to a level that is deleterious to cycle life. This cooling requires efficient paths for escape of heat to cooled surfaces; cooling the exterior of modules is insufficient. If a battery is heated by its own energy, and insulated to withstand exposure to a cold climate, only vacuum insulation will afford an appreciable reduction (>10{degrees}C) in the ambient temperature that can be tolerated. Standard insulations are of little use for this purpose because the heat loss rate causes too high a drain on the battery energy even for near-ambient temperature batteries.
1995-07-01
Theory of oiligopoly: Cournot equilibrium in exhaustible resource markets with fixed supplies
Energy Technology Data Exchange (ETDEWEB)
Assuming Cournot behavior in open loop strategies by the several sellers, an imperfectly competitive market for an exhaustible resource is studied. An equilibrium develops with the following properties: industry production declines over time, as does the present value of market price net of unit extraction cost. The degree of concentration in supply increases over time, tending toward monopoly. Larger firms earn a lower rate of return on their endowment, and perceive a smaller increment to profits from the acquisition of new stocks. Industry prices and supply paths are insensitive to a local redistribution of endowments. The relative deadweight burden of oiligopoly is small for plausible values of market parameters. 14 references.
1983-01-01
Energy Technology Data Exchange (ETDEWEB)
The isothermal flow field for the axial cyclone has been experimentally determined. The velocity fields are used for determination particle paths (particle removal and suspended state), and inter alia of heat and mass transfer processes in the axial cyclone combustion chamber. The results are extremely significant as input value approximations for mathematical modelling, since experimentally obtained results are indispensable for complex flows and geometries. (orig.) [Deutsch] Es ist fuer den Axialzyklon experimentell das isotherme Stroemungsfeld ermittelt. Die Geschwindigkeitsfelder dienen zur Ermittlung der Partikelbahnen (Partikelabscheidung, Schwebebedingung), der Waerme- und Stoffuebertragungsprozesse u.a. in der Axialzyklonbrennkammer. Die Ergebnisse sind als Startwertnaeherung bei einer mathematischen Modellierung sehr wichtig, da bei komplexen Stroemungen und Geometrien versuchstechnische Ergebnisse unumgaenglich sind. (orig.)
1994-12-31
The optimal path of piston motion for Otto cycle with linear phenomenological heat transfer law
British Library Electronic Table of Contents (United Kingdom)
An Otto cycle engine with internal and external irreversibilities of friction and heat leakage, in which the heat transfer between the working fluid and the environment obeys linear phenomenological heat transfer law [q ?? ?(T ?1)], is studied in this paper. The optimal piston motion trajectory for maximizing the work output per cycle is derived for the fixed total cycle time and fuel consumed per cycle. Optimal control theory is applied to determine the optimal piston trajectories for the cases of with and without piston acceleration constraint on each stroke and the optimal distribution of the total cycle time among the strokes. The optimal piston motion with acceleration constraint for each stroke consists of three segments, including initial maximum acceleration and final maximum decel...
2009-01-01
The Xygra gun simulation tool.
Energy Technology Data Exchange (ETDEWEB)
Inductive electromagnetic launchers, or coilguns, use discrete solenoidal coils to accelerate a coaxial conductive armature. To date, Sandia has been using an internally developed code, SLINGSHOT, as a point-mass lumped circuit element simulation tool for modeling coilgun behavior for design and verification purposes. This code has shortcomings in terms of accurately modeling gun performance under stressful electromagnetic propulsion environments. To correct for these limitations, it was decided to attempt to closely couple two Sandia simulation codes, Xyce and ALEGRA, to develop a more rigorous simulation capability for demanding launch applications. This report summarizes the modifications made to each respective code and the path forward to completing interfacing between them.
2008-12-01
The Path to Metallicity: Synthesis of CNO Elements inStandard BBN
Energy Technology Data Exchange (ETDEWEB)
We perform an analysis of the production of elements with mass number A {ge} 12 in a standard Big Bang Nucleosynthesis scenario. The goal is to provide a more accurate estimate of the very low and yet poorly explored abundance of such elements, relevant for the pristine Population III stars. We examine the synthesis channels for these elements in a critically revised and updated version of the Wagoner-Kawano code, as well as in a further enlarged version including four additional nuclides and a significantly extended nuclear network. Our results show no major discrepancies with the ones obtained using a smaller nuclear network. The robustness of the standard predictions--the early generation of star developed in a metal-free environment--is confirmed.
2007-02-12
The Environmental Kuznets Curve. An empirical analysis for OECD countries
Energy Technology Data Exchange (ETDEWEB)
This paper tests the Environmental Kuznets Curve hypothesis for four local (SOx, NOx, CO, VOC) and two global (CO2, GHG) air pollutants. Using a new panel data set of thirty OECD countries, the paper finds that the postulated inverted U-shaped relationship between income and pollution does not hold for all gases. A meaningful Environmental Kuznets Curve exists only for CO, VOC and NOx, where for CO2 the curve is monotonically increasing. For GHG there is indication of an inverted U-shaped relationship between income and pollution, but still most countries are on the increasing path of the curve and hence the future development of the curve is uncertain. For SOx it was found that emissions follow an U-shaped curve. Based on the empirical results, the paper concludes that the Environmental Kuznets Curve does not hold for all gases, it is rather an empirical artefact than a regularity.
2008-09-15
The Environmental Kuznets Curve. An empirical analysis for OECD countries
International Nuclear Information System (INIS)
This paper tests the Environmental Kuznets Curve hypothesis for four local (SOx, NOx, CO, VOC) and two global (CO2, GHG) air pollutants. Using a new panel data set of thirty OECD countries, the paper finds that the postulated inverted U-shaped relationship between income and pollution does not hold for all gases. A meaningful Environmental Kuznets Curve exists only for CO, VOC and NOx, where for CO2 the curve is monotonically increasing. For GHG there is indication of an inverted U-shaped relationship between income and pollution, but still most countries are on the increasing path of the curve and hence the future development of the curve is uncertain. For SOx it was found that emissions follow an U-shaped curve. Based on the empirical results, the paper concludes that the Environmental Kuznets Curve does not hold for all gases, it is rather an empirical artefact than a regularity.
2008-01-01
Study of Zircaloy-2 corrosion in high temperature water using ion beam methods
Energy Technology Data Exchange (ETDEWEB)
Experiments have been carried out in water at 355 C to study transport of oxygen and hydrogen (as deuterium) in growing corrosion films. Composition of the films was also examined in 2.9 Mev and 3.9 Mev /alpha/-particle backscattering experiments. Corrosion occurs predominantly by oxygen diffusion through the film via grain boundary or similar short circuit diffusion paths, to form fresh oxide at the oxide metal interface. Increasing grain size within thick pre-breakaway films contributes to a decrease in diffusivity. The rate transition results from the generation of new diffusion pathways in previously protective oxide. Unexpectedly high concentrations of deuterium were observed. 26 refs.
1981-10-01
International Nuclear Information System (INIS)
Low energy (<100 eV) Ar"+ ion bombardment of the growing film during the deposition of amorphous GaSb+Ge mixtures was found to affect both the transformation rate kinetics as well as the reaction path during subsequent annealing. Ion bombardment induced collisional cascades resulted in more random mixing in the growing films thus retarding the rate of the amorphous to equilibrium state phase transformation during annealing and allowing the formation of homogeneous metastable randomly oriented single phase (GaSb)/sub 1-x/Ge/sub x/ alloys. The films were approx.1.5 #mu#m thick and the average grain size in the metastable state was approx.300 A.
6180-01-01
International Nuclear Information System (INIS)
Monolithic SiAlON ceramics are hard and brittle with little possibility for property design, but multi-phase SiAlON ceramics offer great scope for controlling microstructural development and desired properties. The ceramics can also be reinforced by separate additions of other hard, refractory compounds. The toughness in all these SiAlON composites can be increased by several mechanisms, and the best effect is reached if they are combined. When glassy phase is present, crack paths are affected by the strains caused by different thermal expansion of the glassy phase and the crystals and also by the interface properties. The crystal shape influence toughness, especially pronounced is the effect of the elongated #beta#- grains. Different toughening mechanisms are achieved by separately added reinforcement phases. The hardness is raised by the presence of #alpha# SiAlON and other hard constituents, such as SiC. (orig.).
1993-10-04
Throughout much of the 1980s, deforestation in Brazil eliminated more than 15,000 square kilometers (9000 square miles) of forest per year. Data gathered by several satellites in the Landsat series of spacecraft shows enormous tracts of forest disappearing in Rondonia, Brazil from 1975 through 2001. The human phenomenon of deforestation starts, especially in the dense tropical forests of Brazil, when systematic cutting of a road opens new territory to potential deforestation by penetrating into new areas. Clearing of vegetation along the sides of those roads then tends to fan out to create a pattern akin to a fish skeleton. As new paths appear in the woods, more areas become vulnerable. Finally, the spaces between the skeletal bones fall to defoliation.
2005-02-17
Real-time monitoring of moisture levels in wound dressings in vitro: An experimental study
British Library Electronic Table of Contents (United Kingdom)
Retaining an appropriate level of moisture at the interface between a healing wound and an applied dressing is considered to be critical for effective wound healing. Failure to control exudate at this interface can result in maceration or drying out of the wound surface. The ability to control moisture balance at the wound interface is therefore a key aspect of wound dressing performance. To date it has not been possible to monitor in any effective manner the distribution of moisture within dressings or how this varies with time.A new measurement system is presented based on sensors placed at the wound/dressing interface which are capable of monitoring moisture levels in real time. The system comprises a model wound bed and sensor array complete with fluid injection path to mimic exudate f...
2007-01-01
Radiation Protection Aspects of the Linac Coherent Light Source Front End
Energy Technology Data Exchange (ETDEWEB)
The Front End Enclosure (FEE) of the Linac Coherent Light Source (LCLS) is a shielding housing located between the electron dump area and the first experimental hutch. The upstream part of the FEE hosts the commissioning diagnostics for the FEL beam. In the downstream part of the FEE, two sets of grazing incidence mirror and several collimators are used to direct the beam to one of the experimental stations and reduce the bremsstrahlung background and the hard component of the spontaneous radiation spectrum. This paper addresses the beam loss assumptions and radiation sources entering the FEE used for the design of the FEE shielding using the Monte-Carlo code FLUKA. The beam containment system prevents abnormal levels of radiations inside the FEE and ensures that the beam remains in its intended path is also described.
2010-08-26
Quick. How much material in that pile
Energy Technology Data Exchange (ETDEWEB)
Presented are nomographs for calculating volume of bulk materials (e.g. coal, ores, sand, limestone) in conical or oblong piles formed by means of throwers and other mechanical transporting devices. The author explains that when a thrower is stationary, the pile formed resembles a cone and its projection on the ground is roughly circular. If thrower is moving, in general along a straight path, the final shape is more oblong, resulting from overlapping of separately formed cones. Slope of piles depends on the angle of repose which material makes with the horizontal when piled. This angle depends on such factors as internal friction of material stored, the throwing impact, fineness of grains, and moisture content. Volume is determined from the angle of repose and geometrical data on the area occupied by the pile.
1982-10-01
Quantum coherence in ion channels: resonances, transport and verification
Energy Technology Data Exchange (ETDEWEB)
Recently it was demonstrated that long-lived quantum coherence exists during excitation energy transport in photosynthesis. It is a valid question up to which length, time and mass scales quantum coherence may extend, how one may detect this coherence and what, if any, role it plays in the dynamics of the system. Here we suggest that the selectivity filter of ion channels may exhibit quantum coherence, which might be relevant for the process of ion selectivity and conduction. We show that quantum resonances could provide an alternative approach to ultrafast two-dimensional (2D) spectroscopy to probe these quantum coherences. We demonstrate that the emergence of resonances in the conduction of ion channels that are modulated periodically by time-dependent external electric fields can serve as signatures of quantum coherence in such a system. Assessments of experimental feasibility and specific paths towards the experimental realization of such experiments are ...
2010-08-15
Point-splitting regularization of composite operators and anomalies
The point-splitting regularization technique for composite operators is discussed in connection with anomaly calculation. We present a pedagogical and self-contained review of the topic with an emphasis on the technical details. We also develop simple algebraic tools to handle the path ordered exponential insertions used within the covariant and non-covariant version of the point-splitting method. The method is then applied to the calculation of the chiral, vector, trace, translation and Lorentz anomalies within diverse versions of the point-splitting regularization and a connection between the results is described. As an alternative to the standard approach we use the idea of deformed point-split transformation and corresponding Ward-Takahashi identities rather than an application of the equation of motion, which seems to save the complexity of the calculations.
2000-01-01
British Library Electronic Table of Contents (United Kingdom)
This study aimed to explore the impact of perceived service quality and self-concept on consumer attitude and purchase process using channel type (physical and Internet) as a segmentation variable. From the perspective of consumer behaviour, this study attempted to estimate a relational model and perform an empirical validation using female cosmetics and skincare products as an example. It was discovered that the influence of perceived service quality and self-concept on consumer attitude, purchase intention and behaviour, satisfaction, and loyalty varied with channel type. The analysis result revealed that physical stores presented higher levels of agreement with all research perspectives than Internet stores. However, only two relational paths have a higher influencing effect in physical...
2011-01-01
Partial wave expansion of ion-atom elastic scattering in solids
International Nuclear Information System (INIS)
Elastic scattering cross sections of keV protons in solids (Z=3-82) are calculated using the partial wave expansion technique and the ''muffin-tin'' bound-atom potential. The differential cross sections for small scattering angles of less than 10deg are smaller than those with the Ziegler-Biersack-Littmark potential at all energies and for all solids, although, for larger angles, the two cross sections agree with each other. The mean free paths of the protons in the solids, obtained from the total cross sections, decrease very slowly with decreasing energy. Furthermore, at low energies they approach half the nearest-neighbor distance, which is taken as the radius of the augmented plane wave sphere in the muffin-tin model of crystalline solids. (orig.).
PROSPECTS AND STATUS OF LOW-ASPECT-RATIO TOKAMAKS
Energy Technology Data Exchange (ETDEWEB)
The prospects for the low-aspect-ratio (A) tokamak to fulfill the requirements of viable fusion power plants are considered relative to the present status in data and modeling. Desirable physics and design features for an attractive Blanket Test Facility and power reactors are estimated for low-A tokamaks based on calculations improved with the latest data from small pioneering experiments. While these experiments have confirmed some of the recent predictions for low-A, they also identify the remaining issues that require verification before reliable projections can be made for these deuterium-tritium applications. The results show that the low-A regime of small size, modest field, and high current offers a path complementary to the standard and high A tokamaks in developing the full potential of fusion power.
1995-01-01
Nuclear fission with mean-field instantons
We present a description of nuclear spontaneous fission, and generally of quantum tunneling, in terms of instantons - periodic imaginary-time solutions to time-dependent mean-field equations - that allows for a comparison with more familiar and used generator coordinate (GCM) and adiabatic time-dependent Hartree-Fock (ATDHF) methods. It is shown that the action functional whose value for the instanton is the quasiclassical estimate of the decay exponent fulfils the minimum principle when additional constraints are imposed on trial fission paths. In analogy with mechanics, these are conditions of energy conservation and the velocity-momentum relations. In the adiabatic limit the instanton method reduces to the time-odd ATDHF equation, with collective mass including the time-odd Thouless-Valatin term, while the GCM mass completely ignores velocity-momentum relations. This implies that GCM inertia generally overestimates instanton-related decay rate. The very ...
2007-01-01
Network evolution and QOS provisioning for integrated femtocell/macrocell networks
Integrated femtocell/macrocell networks, comprising a conventional cellular network overlaid with femtocells, offer an economically appealing way to improve coverage, quality of service, and access network capacity. The key element to successful femtocells/macrocell integration lies in its self-organizing capability. Provisioning of quality of service is the main technical challenge of the femtocell/macrocell integrated networks, while the main administrative challenge is the choice of the proper evolutionary path from the existing macrocellular networks to the integrated network. In this article, we introduce three integrated network architectures which, while increasing the access capacity, they also reduce the deployment and operational costs. Then, we discuss a number of technical issues, which are key to making such integration a reality, and we offer possible approaches to their solution. These issues include efficient frequency and interference management, ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
We consider the dynamics towards the initial singularity of Bianchi type IX vacuum and orthogonal perfect fluid models with a linear equation of state. Surprisingly few facts are known about the 'Mixmaster' dynamics of these models, while at the same time most of the commonly held beliefs are rather vague. In this paper, we use Mixmaster facts as a base to build an infrastructure that makes it possible to sharpen the main Mixmaster beliefs. We formulate explicit conjectures concerning (i) the past asymptotic states of type IX solutions and (ii) the relevance of the Mixmaster/Kasner map for generic past asymptotic dynamics. The evidence for the conjectures is based on a study of the stochastic properties of this map in conjunction with dynamical systems techniques. We use a dynamical systems formulation, since this approach has so far been the only successful path to obtain theorems, but we also make comparisons with the 'metric' ...
2009-04-07
Minimum work requirement for water production in humidification?dehumidification desalination cycle
British Library Electronic Table of Contents (United Kingdom)
This paper presents a theoretical analysis based on the second law of thermodynamics for estimating the minimum work required for air dehumidification process to produce potable water in a humidification-dehumidification (HD) desalination cycle. The general air dehumidification process is analyzed through an equivalent path consisting of an isothermal dehumidification followed by a sensible cooling Dehumidification is treated as separation process of an ideal mixture consisting of two components, namely air and water vapor. The present analysis assumes the dead state to be the dry ambient and the final state for complete dehumidification to be saturated air at 0.01?C. Contours of the minimum work are plotted on psychrometric chart and presented as a handy engineering tool to estimate the p...
2007-01-01
Mechanisms of obesity-induced male infertility
British Library Electronic Table of Contents (United Kingdom)
Male infertility, characterized by hypogonadism, decreased semen quality or ejaculatory dysfunction, accounts for approximately 20% of infertility cases. Obesity and metabolic dysfunction have been identified, among other causal factors, to contribute to male infertility. In the context of the Western world's `obesity epidemic', this article discusses three main biological mechanisms linking obesity to impaired male reproductive function: hypogonadism, testicular heat stress/hypoxia-induced apoptosis and endocrine disruption by `obesogens'. Among these, obesity-induced hypogonadism is undoubtedly the most clinically significant and is easily assessed. Rapidly expanding areas of research in this area include leptin modulation of kisspeptins and hypothalamic-pituitary-testicular hormone path...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
In this work, a three-dimensional multiphase non-isothermal model incorporated with a capillary-extended sub-model in gas channels is used to investigate the coupled phenomena of water and thermal transport in proton exchange membrane fuel cells. Distributions of water and temperature along the flow path in the channel are highlighted and the pros and cons of various operating temperatures are elaborated. In addition, this work also sheds light on the impacts of temperature variations of bipolar plates induced by non-uniform cooling conditions, which have been overlooked by most previous works. An important phenomenon of water distribution, dry-out at inlets and flooding at outlets (DIFO), is observed and this non-uniform distribution is revealed to be greatly influenced by the operating t...
2011-01-01
Long Range Correlation in Granular Shear Flow II: Theoretical Implications
Numerical simulations are used to test the kinetic theory constitutive relations of inertial granular shear flow. These predictions are shown to be accurate in the dilute regime, where only binary collisions are relevant, but underestimate the measured value in the dense regime, where force networks of size $\\xi$ are present. The discrepancy in the dense regime is due to non-collisional forces that we measure directly in our simulations and arise from elastic deformations of the force networks. We model the non-collisional stress by summing over all paths that elastic waves travel through force networks. This results in an analytical theory that successfully predicts the stress tensor over the entire inertial regime without any adjustable parameters.
2006-01-01
Energy Technology Data Exchange (ETDEWEB)
The costs of greenhouse gas emission-reductions vary among countries depending on emission levels, technologies used, past emission-reduction achievements, path of economic development, fuel mix, and initial endowment of hydrocarbon resources. The criterion of cost-effectiveness therefore suggests that the ways should be found to encourage emission reductions in the countries where the required costs of reduction of additional unit of emissions are the lowest. These countries usually face crucial capital constraints and have other development priorities than investing in reduction of greenhouse gas emissions. Developed countries could invest their resources in the former Soviet Union and the east European countries to achieve the same level of reduction of greenhouse gases with lower costs than they could in their own countries.
1996-12-31
Interinstitutional Variations in Planning for Stereotactic Body Radiation Therapy for Lung Cancer
British Library Electronic Table of Contents (United Kingdom)
Purpose: The aim of this study was to assess interinstitutional variations in planning for stereotactic body radiation therapy (SBRT) for lung cancer before the start of the Japan Clinical Oncology Group (JCOG) 0403 trial.Methods and Materials: Eleven institutions created virtual plans for four cases of solitary lung cancer. The created plans should satisfy the target definitions and the dose constraints for the JCOG 0403 protocol.Results: FOCUS/XiO (CMS) was used in six institutions, Eclipse (Varian) in 3, Cadplan (Varian) in one, and Pinnacle3 (Philips/ADAC) in one. Dose calculation algorithms of Clarkson with effective path length correction and superposition were used in FOCUS/XiO; pencil beam convolution with Batho power law correction was used in Eclipse and Cadplan; and collapsed co...
2007-01-01
Influence of annealing on the microstructure of commercial Mg alloy AZ31 after mechanical forming
International Nuclear Information System (INIS)
The microstructure of commercial rolled magnesium alloy AZ31B (nominal composition Mg-3Al-0.9Zn-0.15Mn in wt.%) was investigated with the help of light microscopy, electron backscatter diffraction (EBSD) and X-ray diffraction technique after annealing in the temperature range from room temperature (RT) to 400 deg. C. Tensile tests at RT were performed to show the influence of the microstructure on mechanical properties. Static recrystallization (SRX) was observed during annealing of as-received alloy at and above 150 deg. C. Twins play an important role during SRX and serve as nucleation sites and preferred paths for growth of grains. The strong basal texture caused by rolling was weakened by SRX. Significant differences in the stress strain curves were observed for as-received and annealed specimens.
2006-09-25
Energy Technology Data Exchange (ETDEWEB)
The paper describes the latest developments in STRASSY (Strategy Assistance System), the strategy assistance system for the inspection of nuclear materials. The user can now select the fuel cycle he wishes to investigate from an initial range of 19 facilities. An inspection interface has been developed to enable the details and dates of inspections to be modified. One of the special features of the application of STRASSY in international safeguards is the taking into account of timeliness of detection; certain aspects of the time manager algorithms are presented and analysed, including the guaranteed existence of a solution. The results of a study of diversion paths in a simplified cycle consisting of our facilities are presented. Finally, the modifications necessary to enable STRASSY to be used for a posterior analysis of inspection results are discussed. (authors). 7 refs., 3 figs.
1994-12-31
Incorporation of organizational failures in PSA
International Nuclear Information System (INIS)
A large portion of the work performed at nuclear power plants follows standardized flow paths. For example, although components on which the maintenance crew works differ from one assignment to the next, all assignments basically follow the same process: requesting, reviewing, planning, scheduling, executing, testing, and documenting the work. In general, the term open-quotes work processclose quotes is used to refer to a standardized sequence of tasks designed within the operational environment of an organization to achieve a specific goal. The predictable nature of work processes suggests that a systematic analysis can be conducted to identify the desirable design of the process and to develop performance measures with respect to the strengths and weaknesses in the process. Furthermore, because of the close relationship of the work process to plant performance and plant safety, it is believed that such an analysis will facilitate the inclusion of organizational ...
1993-06-20
Improving Dynamic Load and Generator Response PerformanceTools
Energy Technology Data Exchange (ETDEWEB)
This report is a scoping study to examine research opportunities to improve the accuracy of the system dynamic load and generator models, data and performance assessment tools used by CAISO operations engineers and planning engineers, as well as those used by their counterparts at the California utilities, to establish safe operating margins. Model-based simulations are commonly used to assess the impact of credible contingencies in order to determine system operating limits (path ratings, etc.) to ensure compliance with NERC and WECC reliability requirements. Improved models and a better understanding of the impact of uncertainties in these models will increase the reliability of grid operations by allowing operators to more accurately study system voltage problems and the dynamic stability response of the system to disturbances.
2005-11-01
International Nuclear Information System (INIS)
This article describes the project for the installation of an additional emergency diesel generator in both Asco and Vandellos NPPs. The basic objectives of this project are to improve the availability of the emergency generation system, in order to provide greater ability to address potential contingencies, and also to increase the flexibility of the preventive periodic maintenance of the emergency diesel generators. This maintenance, that is currently a milestone of the critical path of the refueling outage, will be performed on-line. The new diesel generator will be sized to support all the loads considered in the safety case and also the consumption of its own auxiliary systems, and will be tested for operability assessment on the same periodical basis than the existing ones. The solution adopted will also permit that the N diesel generator may be connected to any bus bar class 1E in a station black-out scenario. (Author)
International Nuclear Information System (INIS)
Gravitational waves are propagating fluctuations of gravitational fields, that is, '' ripples '' in space-time, generated mainly by moving massive bodies. These distortions of space-time travel with the speed of light. Every body in the path of such a wave feels a tidal gravitational force that acts perpendicular to the wave's direction of propagation; these forces change the distance between points, and the size of the changes is proportional to the distance between these points thus gravitational waves can be detected by devices which measure the induced length changes. The frequencies and the amplitudes of the waves are related to the motion of the masses involved. Thus, the analysis of gravitational waveforms allows us to learn about their source and, if there are more than two detectors involved in observation, to estimate the distance and position of their source on the sky. (author)
2007-12-01
Energy Technology Data Exchange (ETDEWEB)
In parking areas of large extent, the removal of engine exhaust gases, especially of their CO gas components with ventilation plant is mainly done by transverse ventilation over short paths. By their presence, the ventilation ducts required for this purpose often reduce the value of the parking space by restrictions with a consequent reduction of their acceptance by the users. Longitudinal ventilation without ducts can be a remedy in such cases. Depending on the required room air quality in the zones of highest loading, the volume flows with longitudinal removal are no greater than with conventional transverse ventilation. This article is concerned with the different methods of operation of the two systems. (orig./BWI)
1994-04-01
Energy Technology Data Exchange (ETDEWEB)
To gain in efficiency, lightness and volume, the hybrid and electric-powered cars will certainly follow the cellular phone path. The key of success of todays hybrid cars is the Ni-MH battery developed by Matsushita (87.5% of the market in 2004). The lithium-ion batteries will be the next step and would allow to supply 80 to 100% of the energy of the vehicle, the thermal engine becoming just an auxiliary system for additional power, autonomy and air-conditioning. Prototypes can reach today 200 to 450 km of autonomy and 130 km/h speeds with batteries of about 200 kg. If most of the safety problems linked with the Li technology have been solved, the main drawback remains the cost of the Li-ion technology. Short paper. (J.S.)
2005-09-28
Exploring the potential energy surface for proton transfer in acetylacetone
Energy Technology Data Exchange (ETDEWEB)
The portion of the potential energy surface (PES) of acetylacetone relevant for the intramolecular proton transfer reaction is studied using ab initio and DFT methods. The best estimate of the barrier governing proton transfer was found to be 3.4 kcal mol{sup -1} at the MP4(FC)/6-311 + G(2d,2p)//MP2(FC)/6-311 + G(2d,2p) level of theory. Six stationary points on the PES were characterized as well as the reaction paths connecting these points. Special attention paid to the pathway of intramolecular proton transfer reveals that the internal rotation of the methyl group adjacent to the carbonyl group and the proton transfer reaction are consecutive processes.
2004-11-15
Equipment hardening and hardness assurance
International Nuclear Information System (INIS)
The introduction of tolerance to radiation (''radiation-hardness'') into large electronic systems is one of the major tasks to which this Handbook will be put. The practices recommended here for inculcating radiation-tolerance in equipment require advanced physical modeling techniques, precise engineering procedures, and firm assurance procedures. The degree to which these procedures should be used in an equipment project can be measured by the severity of the raw radiation environment, the desired reliability of the system, and the requirement of that project for radiation-sensitive technologies. The balance of device/circuit design versus shielding will depend on whether the radiation is highly penetrating -- as in isotope handling or military environments -- or readily attenuated, as in space. In this chapter the authors have attempted to summarize the essential features of the radiation hardening of large assemblies of equipment and how effective control of radiation effects, that ...
Energy efficient wireless unicast routing alternatives for machine-to-machine networks
British Library Electronic Table of Contents (United Kingdom)
Machine-to-machine (M2M) communications is a new and rapidly developing technology for large-scale networking of devices without dependence on human interaction. Energy efficiency is one of the important design objectives for machine-to-machine network architectures that often contain multi-hop wireless subnetworks. Constructing energy-efficient routes for sending data through such networks is important not only for the longevity of the nodes which typically depend on battery energy, but also for achieving an environmentally friendly system design overall, which will be imperative as M2M networks scale in number of nodes as projected. The objective of this survey is to provide a comprehensive look into shortest-path based energy-efficient routing alternatives to provide a reference for sys...
2011-01-01
Effect of decrease of molybdenum radiation hardening at high energy proton irradiation
International Nuclear Information System (INIS)
By method of transmission electron microscopy and measuring of microhardness the peculiarities of influence of radiation defect clusters on molybdenum radiation hardening along range path of protons with 30 MeV initial energy are studied. Decrease effect of hardening growth value and even its absence depending on irradiation dose in the range of 10-20 MeV proton energies in presence of high density of radiation defect dispersed clusters is revealed. It is shown experimentally that this effect is connected with accumulation of hydrogen up to not very high concentrations (not more than 5x10"-"4 at.%) at the expense of elastic and inelastic proton scattering. 5 refs.; 5 figs.
1990-05-22
British Library Electronic Table of Contents (United Kingdom)
The homogeneity of a helium dielectric barrier discharge, working at atmospheric pressure and containing oxygen as contaminant, is assessed by mapping the spatial distribution of oxygen metastable atoms in relation to the uniformity of surface properties. Tunable diode laser absorption spectroscopy is used to monitor the time evolution of the absorption coefficient corresponding to the oxygen metastable atoms on the 35S2 level, as a function of the laser absorbing path, whereas bi-dimensional Abel transform is used to obtain local information on the space distribution of the metastable atoms in the discharge. The radial distribution of the surface properties is investigated using atomic force microscopy, contact angle measurement and X-ray photoelectron spectroscopy. The results show that ...
2011-01-01
Corruption and the environmental Kuznets Curve: Empirical evidence for sulfur
British Library Electronic Table of Contents (United Kingdom)
We investigate how corruption influences the income level at the turning point of the relationship between sulfur emissions and income, using a wide cross-national panel of countries, at different levels of development and with different degrees of corruption. Our results support the Environmental Kuznets Curve hypothesis for sulfur. We find evidence that the higher the country's degree of corruption, the higher the per capita income at the turning point, suggesting different income-pollution paths across countries due to corruption. We build upon a new specification for the EKC developed by Bradford et al. (2005) that avoids using nonlinear transformations of potentially nonstationary regressors in panel estimation. Also, we account for the indirect impact of corruption on emissions throu...
2010-01-01
Correlation effects in partially ionized mass asymmetric electron-hole plasmas
The effects of strong Coulomb correlations in dense three-dimensional electron-hole plasmas are studied by means of unbiased direct path integral Monte Carlo simulations. The formation and dissociation of bound states, such as excitons and bi-excitons is analyzed and the density-temperature region of their appearance is identified. At high density, the Mott transition to the fully ionized metallic state (electron-hole liquid) is detected. Particular attention is paid to the influence of the hole to electron mass ratio $M$ on the properties of the plasma. Above a critical value of about M=80 formation of a hole Coulomb crystal was recently verified [Phys. Rev. Lett. {\\bf 95}, 235006 (2005)] which is supported by additional results. Results are related to the excitonic phase diagram of intermediate valent Tm[Se,Te], where large values of $M$ have been observed experimentally.
2007-01-01
Energy Technology Data Exchange (ETDEWEB)
In a turbine rotor, a thermal mismatch between various component parts of the rotor occurs particularly during transient operations such as shutdown and startup. A thermal medium flows past and heats or cools one part of the turbine which may have a deleterious thermal mismatch with another part. By passively controlling the flow of cooling medium past the one part in response to relative movement of thermally responsive parts of the turbine, the flow of thermal medium along the flow path can be regulated to increase or reduce the flow, thereby to regulate the temperature of the one part to maintain the thermal mismatch within predetermined limits.
2000-01-01
International Nuclear Information System (INIS)
This paper describes the study of particles' dispersion in an isotropic turbulent flow. The particle's motion and the turbulent flow characteristics are calculated independently. While the particles' displacement is computed by the author's code, the flow is simulated with a commercial code : PowerFLOW. The particles and the flow are coupled through the relative velocity component of the aerodynamic force. When the simulated flow is turbulent, a turbulence regeneration model is used in order to get the flow instantaneous velocity. Validation of the method is done by comparing the particles' dispersion obtained with experimental results from literature and with the results calculated by FLUENT. Good accordance is found between numerical studies and experimental results. However, comparison between results of PowerFLOW coupled to the author's code and results from FLUENT shows differences when the particle's path goes through the turbulent boundary layer. (author)
2004-05-09
Comparative planetology, climatology and biology of Venus, Earth and Mars
British Library Electronic Table of Contents (United Kingdom)
Spacecraft studies of the three terrestrial planets with atmospheres have made it possible to make meaningful comparisons that shed light on their common origin and divergent evolutionary paths. Early in their histories, all three apparently had oceans and extensive volcanism; Mars and Earth, at least, had magnetic fields, and Earth, at least, had life. All three currently have climates determined by energy balance relationships involving carbon dioxide, water and aerosols, regulated by solar energy deposition, atmospheric and ocean circulation, composition, and cloud physics and chemistry. This paper addresses the extent to which current knowledge allows us to explain the observed state of each planet, its planetology, climatology and biology, within a common framework. Areas of ignorance...
2011-01-01
Biaxial Bianchi type 9 quantum cosmology
Energy Technology Data Exchange (ETDEWEB)
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no semiclassical components which would correspond to Lorentzian universes. For the case with a cosmological constant the Hartle-Hawking boundary conditions formally constrain one of the parameters in the Lorentzian solutions to be purely imaginary. Possible interpretations of this imaginary parameter are discussed. 27 refs.
1990-04-01
Biaxial Bianchi type 9 quantum cosmology
International Nuclear Information System (INIS)
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no semiclassical components which would correspond to Lorentzian universes. For the case with a cosmological constant the Hartle-Hawking boundary conditions formally constrain one of the parameters in the Lorentzian solutions to be purely imaginary. Possible interpretations of this imaginary parameter are discussed. 27 refs.
A fundamental Doppler-like but asymmetric wave effect that shifts received signals in frequency in proportion to their respective source distances, was recently described as means for a whole new generation of communication technology using angle and distance, potentially replacing TDM, FDM or CDMA, for multiplexing. It is equivalent to wave packet compression by scaling of time at the receiver, converting path-dependent phase into distance-dependent shifts, and can multiply the capacity of physical channels. The effect was hitherto unsuspected in physics, appears to be responsible for both the cosmological acceleration and the Pioneer 10/11 anomaly, and is exhibited in audio data. This paper discusses how it may be exploited for instant, passive ranging of signal sources, for verification, rescue and navigation; incoherent aperture synthesis for smaller, yet more accurate radars; universal immunity to jamming or interference; and precision frequency scaling of ...
2008-01-01
A study of methyl formate in astrochemical environments
Several complex organic molecules are routinely detected in high abundances towards hot cores and hot corinos. For many of them, their paths of formation in space are uncertain, as gas phase reactions alone seem to be insufficient. In this paper, we investigate a possible solid-phase route of formation for methyl formate (HCOOCH3). We use a chemical model updated with recent results from an experiment where simulated grain surfaces were irradiated with 200 keV protons at 16 K, to simulate the effects of cosmic ray irradiation on grain surfaces. We find that this model may be sufficient to reproduce the observed methyl formate in dark clouds, but not that found in hot cores and corinos.
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
This month, the Cofrentes Nuclear Power Plant celebrates its 18th year of operation, this path is supported rom source by excellent operating results and is cause for the professional pride of those who throughout the years, have been involved on a day to-day basis is its evolution. This article describes the Plant's most significant milestones from the time of its construction up to the present. The different sections cover everything from the most relevant performance indicators to such specific aspects as optimization of refueling times. (Author)
2002-07-01
British Library Electronic Table of Contents (United Kingdom)
This paper presents results from a research case study that examined the distribution of travel time of origin-destination (OD) pairs on a transportation network under incident conditions. Using a transportation simulation dynamic traffic assignment (DTA) model, incident on a transportation network is executed under normal conditions, incident conditions without traveler information availability, and incident conditions assuming that users had perfect knowledge of the incident conditions and could select paths to avoid the incident location. The results suggest that incidents have a different impact on different OD pairs. The results confirm that an effective traveler information system has the potential to ease the impacts of incident conditions network wide. Yet it is also important to n...
2011-01-01
A Network Coding Approach to Loss Tomography
Network tomography aims at inferring internal network characteristics based on measurements at the edge of the network. In loss tomography, in particular, the characteristic of interest is the loss rate of individual links. There is a significant body of work dedicated to this problem using multicast and/or unicast end-to-end probes. Independently, recent advances in network coding have shown that there are several advantages from allowing intermediate nodes to process and combine, in addition to just forward, packets. In this paper, we pose the problem of loss tomography in networks that have network coding capabilities. We design a framework for estimating link loss rates, which leverages network coding capabilities and we show that it improves several aspects of tomography, including the identifiability of links, the tradeoff between estimation accuracy and bandwidth efficiency, and the complexity of probe path selection. We discuss the cases of inferring: the ...
2010-01-01
A Detailed Investigation on Human-Related Unplanned Reactor Trip Events in Korea
International Nuclear Information System (INIS)
Human errors have been reported as one of the most significant causes of major events in nuclear power plants (NPPs). For example, Kim and Park found that about 23% of the major events that occurred at NPPs in Republic of Korea from 1986 to 2006 were caused by human errors. For this reason, a detailed analysis on human errors is an important task for increasing the safety of NPPs. Kim and Choi?2 analyzed 100 human-related unplanned reactor trip events in the Republic of Korea from 1986 to 2006 to consider the type of human errors based on the simple path model for human-induced unplanned reactor trips developed by Kim and Park. In this paper, we will investigate and perform a detailed analysis of the data to identify human-related unplanned reactor trip trends
2010-10-01
Trajectory generation for car-like robots
Energy Technology Data Exchange (ETDEWEB)
Autonomous robots or remotely operated vehicles have raised high hopes in the military and industrial communities because of the potential safety improvement and gain of productivity they may provide. Waste management on nuclear sites, pallet manipulation in factories, interventions on battle-fields, etc., are actively studied. A lot of these applications require powerful four-wheel vehicles, the kinematics of which is similar to that of a car. Such vehicles have three degrees of freedom: the (x,y) positions in a plane and the orientation of the vehicle. Path planning is often understood as only changing the position of the vehicle, whereas the tasks performed by this kind of robot requires a perfect orientation of the vehicle: forklifting a pallet or docking at a loading or unloading station requires accuracy in the orientation of the vehicle. It is this requirement and the kinematic constraints of the motion mode which have led to the ...
1990-01-01
Synopsis of some preliminary computational studies related to unsaturated zone transport at Area G
Energy Technology Data Exchange (ETDEWEB)
Computational transport models are described with applications in three problem areas related to unsaturated zone moisture movement beneath Area G. These studies may be used to support the ongoing maintenance of the site Performance Assessment. The three areas include: a 1-D transient analysis with average tuff hydraulic properties in the near surface region with computed results compared to field data; the influence on near surface transient moisture percolation due to realistic distributions in hydraulic properties derived statistically from the observed variance in the field data; and the west to east moisture flow in a 2-D steady geometry approximation of the Pajarito Plateau. Results indicate that a simple transient model for transport of moisture volume fraction fits field data well compared to a moisture pulse observed in the active disposal unit, pit 37. Using realistic infiltration boundary conditions for summer showers and for spring snow melt conditions, the computed ...
1998-03-01
Surface excitation correction of the inelastic mean free path in selected conducting polymers
International Nuclear Information System (INIS)
In earlier works, the inelastic mean free path (IMFP) of electrons was determined by elastic peak electron spectroscopy (EPES) using Ni and Ag reference standard samples, but fully neglecting surface excitation. Surface excitation that is characterized by the surface excitation parameter (SEP), and may affect considerably the elastic peak for the sample and the reference material. The SEP parameters of selected conducting polymers (polythiophenes, polyaniline and polyethylene) were determined by EPES using Si and Ge reference samples. Experiments were made with a hemispherical analyzer of energy resolution 100-200 meV in the E = 0.2-2.0 keV energy range. The composition of the sample surfaces was determined by in situ XPS, their surface roughness by AFM. The experimental SEP parameter data of eight polymer samples were determined by our new procedure, using the formulae of Chen and Werner et al. in the E = 0.2-2.0 keV energy range. The trial and error procedure is ...
2006-05-15
International Nuclear Information System (INIS)
A fast and accurate segmentation of organs at risk, such as the healthy colon, would be of benefit for planning of radiotherapy, in particular in an adaptive scenario. For the treatment of pelvic tumours, a great challenge is the segmentation of the most adjacent and sensitive parts of the gastrointestinal tract, the sigmoid and descending colon. We propose a semi-automated method to segment these bowel parts using the fast marching (FM) method. Standard 3D computed tomography (CT) image data obtained from routine radiotherapy planning were used. Our pre-processing steps distinguish the intestine, muscles and air from connective tissue. The core part of our method separates the sigmoid and descending colon from the muscles and other segments of the intestine. This is done by utilizing the ability of the FM method to compute a specified minimal energy functional integrated along a path, and thereby extracting the colon centre line between user-defined control points ...
2010-09-21
Energy Technology Data Exchange (ETDEWEB)
The current specifications of the LLNL fusion-fission hybrid proposal, namely LIFE, impose severe constraints on materials, and in particular on the nuclear fissile or fertile nuclear fuel and its immediate environment. This constitutes the focus of the present report with special emphasis on phase formation and phase transformations of the transmutation fuel and their consequences on particle and pebble thermal, chemical and mechanical integrities. We first review the work that has been done in recent years to improve materials properties under the Gen-IV project, and with in particular applications to HTGR and MSR, and also under GNEP and AFCI in the USA. Our goal is to assess the nuclear fuel options that currently exist together with their issues. Among the options, it is worth mentioning TRISO, IMF, and molten salts. The later option will not be discussed in details since an entire report is dedicated to it. Then, in a second part, with the specific LIFE specifications in mind, ...
2008-11-10
Molar excess volumes of liquid hydrogen and neon mixtures from path integral simulation
Energy Technology Data Exchange (ETDEWEB)
Volumetric properties of liquid mixtures of neon and hydrogen have been calculated using path integral hybrid Monte Carlo simulations. Realistic potentials have been used for the three interactions involved. Molar volumes and excess volumes of these mixtures have been evaluated for various compositions at 29 and 31.14 K, and 30 atm. Significant quantum effects are observed in molar volumes. Quantum simulations agree well with experimental molar volumes. Calculated excess volumes agree qualitatively with experimental values. However, contrary to the existing understanding that large positive deviations from ideal mixtures are caused due to quantum effects in Ne{endash}H{sub 2} mixtures, both classical as well as quantum simulations predict the large positive deviations from ideal mixtures. Further investigations using two other Ne{endash}H{sub 2} potentials of Lennard{endash}Jones (LJ) type show that excess volumes are very sensitive to the cross-interaction ...
1999-07-01
Molar excess volumes of liquid hydrogen and neon mixtures from path integral simulation
International Nuclear Information System (INIS)
Volumetric properties of liquid mixtures of neon and hydrogen have been calculated using path integral hybrid Monte Carlo simulations. Realistic potentials have been used for the three interactions involved. Molar volumes and excess volumes of these mixtures have been evaluated for various compositions at 29 and 31.14 K, and 30 atm. Significant quantum effects are observed in molar volumes. Quantum simulations agree well with experimental molar volumes. Calculated excess volumes agree qualitatively with experimental values. However, contrary to the existing understanding that large positive deviations from ideal mixtures are caused due to quantum effects in Ne - H_2 mixtures, both classical as well as quantum simulations predict the large positive deviations from ideal mixtures. Further investigations using two other Ne - H_2 potentials of Lennard - Jones (LJ) type show that excess volumes are very sensitive to the cross-interaction potential. We conclude that the ...
1999-07-01
Make Markets Work for Climate. Background Document
Energy Technology Data Exchange (ETDEWEB)
Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies in rapidly-growing economies in the developing world will be an essential component of global efforts to alter the ...
2006-07-01
Energy Technology Data Exchange (ETDEWEB)
The current specifications of the LLNL fusion-fission hybrid proposal, namely LIFE, impose severe constraints on materials, and in particular on the nuclear fissile or fertile nuclear fuel and its immediate environment. This constitutes the focus of the present report with special emphasis on phase formation and phase transformations of the transmutation fuel and their consequences on particle and pebble thermal, chemical, and mechanical integrities. We first review the work that has been done in recent years to improve materials properties under the Gen-IV project, and with in particular applications to HTGR and MSR, and also under GNEP and AFCI in the USA. Our goal is to assess the nuclear fuel options that currently exist together with their issues. Among the options, it is worth mentioning TRISO, IMF, and molten salts. The later option will not be discussed in details since an entire report (Volume 8 - Molten-salt Fuels) is dedicated to it. Then, in a second part, with the specific ...
2008-12-19
Initial results of the CD-1 reliable multicast experiment
Energy Technology Data Exchange (ETDEWEB)
During the past year, an experiment has been underway to test use of reliable multicast capabilities for transmission of continuous data in the Global Communication Infrastructure. For the experiment a version of the CD-1 protocol was multicast enabled. The experiment has demonstrated the feasibility of transmitting data in a multicast mode over the GCI. In the case of the Comprehensive Nuclear Test-Ban Treaty the sender could be the station and the receivers the International Data Center (IDC) and one or more National Data Centers (NDC). The potential advantages of multicasting include (a) the timely receipt of the data by the IDC and the host NDC and (b) the simultaneous availability of the raw station data at, at least, two locations. The latter, by introducing redundant data paths, decreases the probability of loss of station data due to a potential failure of a single data receiver. This experiment is only one element of a needed more thorough assessment of ...
2000-09-29
Grid-Search Location Methods for Ground-Truth Collection From Local and Regional Seismic Networks
Energy Technology Data Exchange (ETDEWEB)
This project investigated new techniques for improving seismic event locations derived from regional and local networks. The technqiues include a new approach to empirical travel-time calibration that simultaneously fits data from multiple stations and events, using a generalization of the kriging method, and predicts travel-time corrections for arbitrary event-station paths. We combined this calibration approach with grid-search event location to produce a prototype new multiple-event location method that allows the use of spatially well-distributed events and takes into account correlations between the travel-time corrections from proximate event-station paths. Preliminary tests with a high quality data set from Nevada Test Site explosions indicated that our new calibration/location method offers improvement over the conventional multiple-event location methods now in common use, and is applicable to more general event-station geometries than ...
2005-05-13
Energy Technology Data Exchange (ETDEWEB)
Since the integrity of the containment penetrations was confirmed under accident management (AM) conditions in the former test, failure criteria tests and aerosol trapping tests were carried out using low-voltage modules and flange gaskets of an actual plant under severe accident (SA) conditions, without AM. The safety margin for failure temperature of the penetrations and the credit for fission product (FP) aerosol trapping effect along the leakage paths of the degraded penetrations were evaluated in the present tests. Failure temperature of the penetrations ranged from 270 to 300degC for low-voltage modules and 300 to 350degC for flange gaskets under 0.4 to 1.0 MPa conditions. Pressure dependency on failure temperature was small. This means that the safety margin of failure temperature under AM condition is more than 70degC. By introducing a equivalent leak area for the damaged test pieces, total leak area was estimated which was smaller than the value used in ...
1999-07-01
Estimation of source term release during SGTR sequences at Wolsong plants
International Nuclear Information System (INIS)
Source term release characteristics are analyzed for the severe SGTR (Steam Generator Tube Rupture) sequences beyond the design basis accidents in Wolsong 2/3/4 plants which are of CANDU6 type reactor. In PWRs, SGTR sequences have long been recognized to be important and are distinctly different from the non-bypass sequences since there is a direct fission product release path from the primary system to the environment bypassing the containment gas volume. Meanwhile, a SGTR in a CANDU reactor is analyzed not to provide a complete and direct path into the environment for the source term resulting from a severe accident. This is because the majority of the fission product released arises from heatup and interactions of the disassembled fuel channel segments and debris in the calandria tank rather than from fuel heatup in the fuel channel. These fission products are released from the calandria tank into the containment atmosphere through the four ...
1998-10-21
International Nuclear Information System (INIS)
We measured neutron time-of-flight spectra from 90 MeV protons and 140 MeV alpha particles bombarding thin targets of Al, Ni, Zr, and Bi at laboratory angles between 20_0 and 135_0. The low-energy (5 to 45 MeV) portions of the spectra were measured with 5 cm diameter by 5 cm deep NE-213 counters at 1 m flight paths with n-#betta# pulse-shape discrimination. The high-energy (35 to 150 MeV) portions of the spectra were measured with 12.7 cm diameter by 10.2 cm deep NE-102 counters at flight paths of 2.0 to 5.0 m. The proton-induced measured neutron spectra reveal three distinct energy regions: a low-energy evaporation region, a high-energy region dominated by the quasifree scattering process, and an intermediate-energy region dominated by multistep, preequilibrium processes. In the latter two regions, the spectra show strong angular dependence. The alpha-particle induced neutron spectra show these same distinct energy regions plus an exponential ...
AIRBORNE, OPTICAL REMOTE SENSING OF METHANE AND ETHANE FOR NATURAL GAS PIPELINE LEAK DETECTION
Energy Technology Data Exchange (ETDEWEB)
Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. This second six-month technical report summarizes the progress made towards defining, designing, and developing the hardware and software segments of the airborne, optical remote methane and ethane sensor. The most challenging task to date has been to identify a vendor capable of designing and developing a light source with the appropriate output wavelength and power. This report will document the work that has been done to identify design requirements, and potential vendors for the light source. Significant progress has also been made in characterizing the amount of light return available from a remote target at various distances from the light source. A great deal of time has been spent ...
2003-11-12
Production and Purification of UO_3 from rock phosphate deposits and its characterization
International Nuclear Information System (INIS)
This study was carried out mainly to produce uranium trioxide (UO_3), matching standard commercial specification from rock phosphate deposits in Uro and Kurun at eastern part of the Nuba Mountains. A simplified hydrometallurgical procedure has been adopted for production of yellow cake from the ore. The powdered ore sample was leached with concentrated H_2SO_4 acid with and without addition of KCIO_3 as an oxidant. The crude yellow cake was precipitated from the resulting green solution of phosphoric acid as Na_2U_2O_7 and (NH_4)_2U_2O_7 and subsequently purified by TBP extraction (tributylphosphate) and hydrogen peroxide as UO_4.2H_2O. TBP purified product was dried and calcined to UO_3 whereas UO_4.2H-2O was dried and reduced to UO_3 by Na_2S_2O_3. Prior to precipitation of crude yellow cake, Fe in the phosphoric acid solution was precipitated using magnesia. Elemental analysis has shown that the ore is rich in Ca and deficient in elements of potential interest ...
2005-03-01
Energy Technology Data Exchange (ETDEWEB)
Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The optimum calcining ...
2007-05-04
Energy Technology Data Exchange (ETDEWEB)
Three phosphate based ceramics were studied for the immobilization of tri- and tetravalent actinides: britholites Ca{sub 9}Nd{sub 1-x}An{sub x} {sup IV}(PO{sub 4}){sub 5-x}(SiO{sub 4}){sub 1+x}F{sub 2}, monazites/brabantites Ln{sub 1-2x}{sup III}Ca{sub x}An{sub x}{sup IV}PO{sub 4} and Thorium Phosphate Diphosphate (TPD) Th{sub 4-x}An{sub x}{sup IV}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}. For each material, the incorporation of Th, U(IV), or Ce(IV) in the structure was examined. This work was the early beginning of the incorporation of {sup 239}Pu and/or {sup 238}Pu in order to evaluate the effects of {alpha} -decay on these three crystallographic structures. The syntheses were carried out using dry chemistry methods, involving mechanical grinding then heating treatment (1100 deg C {<=} {theta} {<=} 1400 deg C). For britholites, we showed that the incorporation of thorium was complete for weight loading lower than 20 wt.% through the (Nd{sup 3+}, PO{sub 4}{sup 3-}) ...
2004-07-01
International Nuclear Information System (INIS)
Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and cleaner method which has different heat transfer mechanism and temperature profile ...
2010-11-24
Energy Technology Data Exchange (ETDEWEB)
Er{sub 3}NbO{sub 7} phosphor was synthesized by sintering a mixture of Er{sub 2}O{sub 3} and Nb{sub 2}O{sub 5} powder in a molar ratio of 3:1 at 1600 deg. C over 55 h. Optical absorption and emission characteristics of Er{sup 3+} ions in the calcined Er{sub 3}NbO{sub 7} powder were investigated and discussed compared with ErNbO{sub 4} phosphor and a Z-cut congruent Er (2 mol%):LiNbO{sub 3} single crystal. The absorption and emission studies show that, due to different crystal structures, the spectroscopic properties of these niobates have some differences in spectral shape, peak position, and relative intensity, especially at 1.5 {mu}m. The most obvious spectral feature of the Er{sub 3}NbO{sub 7} is that the spectral structure of band instead of peak is observed in its absorption or emission spectrum due to the existence of local structural disorder and multiple Er{sup 3+} sites. The Er{sub 3}NbO{sub 4} shows stronger upconversion emission than the single crystal ...
2007-12-15
A.C.R.O. activity report 2002; A.C.R.O. rapport d'activite 2002
Energy Technology Data Exchange (ETDEWEB)
A.C.R.O. (Association pour le Controle de la Radioactivite dans l Ouest) is a French non governmental organisation that operates a laboratory for radioactivity analysis. It was created in 1986 as a response to people demands for information and reliable, independent testing. The organisation mainly carries out missions of information and training for its correspondents and more generally for a wide audience, particularly for people who worry about problems of environment, health, management of radioactive waste and emissions. Thanks to its structure, it enables citizens to involve themselves together with scientists so as to gain access to information that was hither to reserved to specialists. The organisation can vouchsafe its independence from the diversity of its members and volunteers, as well as from the diversity of its money resources. Besides its headquarters situated on the city of Caen area (Normandy), three branches situated in North Normandy, in Touraine and North Cotentin ...
2002-07-01
The Path to Fusion Energy for Concepts Currently at the Concept Exploration Level
Energy Technology Data Exchange (ETDEWEB)
Concept Exploration (CE) experiments within the Innovative Confinement Concept Program have a unique role which impacts their contributions to the development of fusion energy. As stated in the FESAC ''Report on Alternate Concepts:'' These [CE] programs are aimed at innovation and basic understanding of relevant scientific phenomena. The emphasis on innovation motivates their application to the search for a better fusion reactor configuration. In addition, because of their unique character the CE experiments offer excellent opportunities to couple fusion-plasma physics to other sciences. A recent example of coupling is the fusion self-organized plasmas to reconnection physics and extra-terrestrial plasmas. Perhaps of even greater importance is the education of the future scientists needed for developing fusion energy. The CE experiments, both at universities and national labs, are of a size students can ''get their hands ...
2003-01-09
[Computed tomography in gunshot trauma. I. Ballistics elements and the mechanisms of the lesions].
The knowledge of wound ballistics and of wounding mechanisms is mandatory for the radiologist to interpret the CT findings of gunshot wounds. The severity of a bullet wound depends on the characteristics of the tissue it goes through, i.e., tissue elasticity, density, thickness of the wounded body part, the type of tissue, its specific gravity, internal cohesiveness and anatomical relationships, as well as on missile characteristics, i.e., mass, shape, fragmentation and deformation. Bullet velocity is certainly a major factor in wounding, but it is only one factor. Two major wounding mechanisms exist the crushing of the bullet-struck tissue (forming the permanent cavity) and radial stretching (forming a temporary cavity). Bullet "yaw" is defined as the angle between the long axis of the bullet and its flight path. The yaw is directly proportional to tissue crushing and stretching: the wider the yaw, the most severe tissue crushing and stretching and, therefore, the ...
1995-04-01
Water management studies in PEM fuel cells, Part I: Fuel cell design and in situ water distributions
Energy Technology Data Exchange (ETDEWEB)
A proton exchange membrane fuel cell (PEMFC) must maintain a balance between the hydration level required for efficient proton transfer and excess liquid water that can impede the flow of gases to the electrodes where the reactions take place. Therefore, it is critically important to understand the two-phase flow of liquid water combined with either the hydrogen (anode) or air (cathode) streams. In this paper, we describe the design of an in situ test apparatus that enables investigation of two-phase channel flow within PEMFCs, including the flow of water from the porous gas diffusion layer (GDL) into the channel gas flows; the flow of water within the bipolar plate channels themselves; and the dynamics of flow through multiple channels connected to common manifolds which maintain a uniform pressure differential across all possible flow paths. These two-phase flow effects have been studied at relatively low operating temperatures under steady-state conditions and ...
2009-05-15
International Nuclear Information System (INIS)
The VE (ventilation) test carried out at the Mont Terri underground laboratory in Switzerland intended to evaluate in situ the behaviour of a consolidated clay formation when subjected to alternate periods of flow of wet and dry air during several months. For that, a 10-m gallery was excavated in the Opalinus Clay formation and carefully instrumented. Before and after a second ventilation phase boreholes were drilled. Samples were taken from the drill cores and were analysed from mineralogical and geochemical points of view. Also, the retention curves of these samples were determined in the laboratory following drying paths performed under free volume conditions at 20 degree centigrade, what is the content of this report. Although there are not large differences in the WRC of samples taken from different boreholes, at different distances from the gallery wall or before or after ventilation, those samples taken near the gallery wall and after ventilation tend to ...
2010-11-01
Visualization study on the static flow field around a straight-bladed vertical axis wind turbine
Visual experiments based on the smoke wire way were carried out on a small model of Straight-blade Vertical Axis Wind Turbine (SB-VAWT) to invest the relationship between the static flow field characteristics and the rotor azimuth angle. The test rotor had 3 blades with NACA0018 aerofoil. The rotor diameter and blade chord were 0.3m and 0.07m, respectively. Visual photos of the static flow path lines in and around the rotor were obtained at every 5 degrees of the azimuth angle. Further, numerical computations of the static flow filed were also carried out for comparison with the same situation as the visual tests and the static torques at different azimuth angles were calculated. According to the results of visual tests and computations, the dependence of the starting performance on the azimuth angle was discussed. The solidity is an important factor affecting the starting performance of the SB-VAWT.
2009-12-01
Van Der Pol model of a Cerenkov maser
Energy Technology Data Exchange (ETDEWEB)
A non-linear analysis of a Cerenkov maser is presented. The system consists of a ring configuration of a cylindrical waveguide filled with a dielectric material. A single transverse-magnetic mode is assumed to propagate in the system. A low-density pencil electron beam travels in part of the ring, confined by a strong axial magnetic field. Using the single-particle description for the beam and the wave equation for the field, we obtain a set of two coupled non-linear differential equations describing the slowly varying amplitude and phase of the electromagnetic mode. The gain per path is assumed to be small and the spatial growth of the field is neglected. The resulting time dependent amplitude includes the exponential gain of the linear stage and the saturation to its maximum value. The time dependent frequency is also calculated. The two equations are combined to a single Van Der Pol equation with a non-linear restoring force. This description demonstrates the ...
1995-12-31
Uplink Capacity and Interference Avoidance for Two-Tier Cellular Networks
This paper presents an uplink capacity analysis and interference avoidance technique for a femtocell based two-tier DS-CDMA network using shared spectrum. Assuming randomly distributed macrocell users and femtocell base stations (BS), we evaluate a network-wide area spectral efficiency metric called the operating contour (OC) defined as the feasible combinations of the average macrocell users and femtocell BS per cell-site that meet a target outage constraint $\\epsilon$. A contribution of this work is an accurate characterization of the uplink outage probability taking cross-tier power control, path-loss and shadowing effects into account. We show that a time-hopped CDMA physical layer coupled with sectorized receive antennas shows dramatic performance improvements in both light and heavily loaded two-tier networks, relative to a split spectrum two-tier network with omnidirectional femtocell antennas. These results provide insights into design of robust shared ...
2007-01-01
Unsaturated zone flow modeling for GWTT-95
Energy Technology Data Exchange (ETDEWEB)
In accordance with the Nuclear Regulatory Commission regulation regarding groundwater travel times at geologic repositories, various models of unsaturated flow in fractured tuff have been developed and implemented to assess groundwater travel times at the potential repository at Yucca Mountain, Nevada. Kaplan used one-dimensional models to describe the uncertainty and sensitivity of travel times to various processes at Yucca Mountain. Robey and Arnold et al. used a two-dimensional equivalent continuum model (ECM) with inter- and intra-unit heterogeneity in an attempt to assess fast-flow paths through the unsaturated, fractured tuff at Yucca Mountain (GWTT-94). However, significant flow through the fractures in previous models was not simulated due to the characteristics of the ECM, which requires the matrix to be nearly saturated before flow through the fractures is initiated. In the current study (GWTT-95), four two-dimensional cross-sections at Yucca Mountain are ...
1995-12-31
Undoing forgetfulness: Chiasmus of Poetical Mind - a Cultural Paradigm of Archetypal Imagination
DEFF Research Database (Denmark)
Abstract This paper tries to investigate the problem of memory through one of its most intriguing patterns - chiasmus - reflected in old poetry, sacred texts, philosophy and theology, visual arts, as well as biology. It aims to search for some provisory explanation of why man was able once to acquire such excellence in memorizing internally thousands of lines of poetry, whereas now memory is expelled outside the human body and mind in a mere digital file. Contrasting the so-called "wish-dream for immortality" of the contemporary post-human body, this paper takes another path and looks into some old cosmologies and visions in which chiasmus constantly emerged as an enduring cultural paradigm with ontological relevance. Spanning from Plato to Christian theology, up to the contemporary Neo-Platonism of archetypal psychology, this paper hopes to put forth, if not a theory, at least a vision about man and cosmos, cosmos and man, a chiastic epiphany in which the body and ...
2005-01-01
Ultrasonic Phased Array Implementation of the Inside Diameter Creeping Wave Sizing Method
Energy Technology Data Exchange (ETDEWEB)
This paper describes a technique for implementing the ultrasonic inside diameter (ID) creeping wave technique for detection and sizing ID connected defects using a phased array ultrasonic system. The technique uses multiple focal laws to produce the examination modes. The first focal law is designed to create a shear wave nominally at the critical angle for mode conversion to a longitudinal wave at the ID of a part, thus creating a creeping wave. This focal law is focused at the ID to improve sensitivity. The rest of the laws are designed to create tandem sound paths that progress up a vertical surface directly above the focal point of the creeping wave generation point. When a defect on the inner surface is detected with the creeping wave, the height of the defect can be measured from the response of a set of tandem laws without readjusting the position of the probe. Results from standard one-inch long notches of varying depths are presented.
2006-05-01
Type Ia supernova science 2010-2020
In the next decade Type Ia supernovae (SNe Ia) will be used to test theories predicting changes in the Dark Energy equation of state with time. Ultimately this requires a dedicated space mission like JDEM. SNe Ia are mature cosmological probes --- their limitations are well characterized, and a path to improvement is clear. Dominant systematic errors include photometric calibration, selection effects, reddening, and population-dependent differences. Building on past lessons, well-controlled new surveys are poised to make strides in these areas: the Palomar Transient Factory, Skymapper, La Silla QUEST, Pan-STARRS, the Dark Energy Survey, LSST, and JDEM. They will obviate historical calibrations and selection biases, and allow comparisons via large subsamples. Some systematics follow from our ignorance of SN Ia progenitors, which there is hope of determining with SN Ia rate studies from 0 2009-01-01
Turbocharger for micro-cars; Keijidoshayo turbocharger
Energy Technology Data Exchange (ETDEWEB)
This paper explains technologies for turbo chargers used in light cars. Light car engine turbo chargers have been given various improvements responding to needs of the market. Since ball bearings have less mechanical loss than sliding bearings, and enhances greatly the turbo efficiency, they are used in some high performance engines of light cars. While the conventional ball bearing has used high hardness bearing steel, the new standard cars started using ceramic ball. The currently used light car gasoline engines are divided into two kinds, serial three-cylinder type and serial four-cylinder type, either having merits and demerits. The new twin entry turbo developed by IHI arranges divided exhaust gas ports above and below to simplify the manifold shape, and realizes smooth flow by twisting the exhaust gas flow path inside the turbine housing. This makes the dynamic pressure of the exhaust gas more effectively utilized, enhancing the boost pressure and torque. ...
2000-05-20
Triaxial determination of shear strength of tire chips
Energy Technology Data Exchange (ETDEWEB)
Triaxial compression tests following stress paths of constant {sigma}{sub 1} were conducted to determine the shear strength of five processed scrap tire products having different gradations and particle shapes. The interparticle frictional component was separated from the total shear strength according to the energy correction concept proposed by researchers. The experimental results show that all five tire chip products have ultimate internal friction angles of 45{degree} to over 60{degree}. The interparticle frictional component of the strength was fully mobilized and nearly reached a constant value after approximately 5% axial strain. The experimental results confirmed that the strength parameter obtained with constant {sigma}{sub 1} was more reasonable. This finding is supported by field observation in which the tire chips have an angle of repose ranging from 37{degree} to 43{degree} (loosely stock piled) and up to 85{degree} (compacted). The engineering ...
1997-05-01
Energy Technology Data Exchange (ETDEWEB)
Time contour expression of limited range phenomena on stack chart is examined for further improvement on the result of the ultimate interpretation in the seismic reflection survey. The policy is made clear from the beginning that local phenomena are to be discussed, and data prior CMP stacking is interpreted in detail. For this purpose, it is effective to make use of the time contour expression in the midpoint-offset plane simultaneously with the CMP and COP panels. For the review of data prior to CMP stacking, it is convenient to use the CMP (CDP) stacking chart in which the data is arranged methodically. In this chart, all the channels which are crude data prior to stacking are plotted on midpoint-offset coordinates, which plane is called the MOD (Midpoint Offset Domain) panel. Various panels can be chosen unrestrictedly, and their mutual relations can be easily grasped. When data points are given a time axis, they can be expressed in a time contour. Studies are conducted about the ...
1997-05-27
Thomson Scattering at FLASH - Status Report
Energy Technology Data Exchange (ETDEWEB)
The basic idea is to implement Thomson scattering with free electron laser (FEL) radiation at near-solid density plasmas as a diagnostic method which allows the determination of plasma temperatures and densities in the warm dense matter (WDM) regime (free electron density of n{sub e} = 10{sup 21}-10{sup 26} cm{sup -3} with temperatures of several eV). The WDM regime [1] at near-solid density (n{sub e} = 10{sup 21}-10{sup 22} cm{sup -3}) is of special interest because, it is where the transition from an ideal plasma to a degenerate, strongly coupled plasma occurs. A systematic understanding of this largely unknown WDM domain is crucial for the modeling and understanding of contemporary plasma experiments, like laser shock-wave or Z-pinch experiments as well as for inertial confinement fusion (ICF) experiments as the plasma evolution follows its path through this domain.
2007-11-28
The path to the future: The role of science and technology at Argonne National Laboratory
Energy Technology Data Exchange (ETDEWEB)
Today some scientists are concerned that present budget considerations in Washington will make it impossible for the US to maintain its preeminence in important areas of science and technology. In the private sector there has been a demise of substantive R & D efforts through most of the major industries. For DOE a lack of future support for science and technology would be an important issue because this could impact DOE`s abilities to solve problems in its major areas of concern, national security, energy, environment. In fact some scientists maintain that were the present trend to continue unabated it could lead to a national security issue. Preeminence in science and technology plays a critical role in our nation`s position as the leader of world democracy. In contrast with this point of view of gloom and doom, however, in this presentation I hope to bring to you what I see as an exciting message of good news. Today I will list the important opportunities and challenges for the ...
1996-04-30
The emergence of Special and Doubly Special Relativity
In a previous paper [Phys.Rev.D82, 085016(2010)] we introduced a method for obtaining the exact Feynman propagator of a relativistic particle (for both Klein-Gordon and Dirac case) from a superstatistical average over non-relativistic single-particle paths. We suggested that this method could offer new insights into the currently much debated issue of emergent relativity. In this paper we proceed further, showing that a Brownian motion on a short scale originates a relativistic motion on scales larger than particle's Compton wavelength. Viewed in this way, special relativity is not a primitive concept, but rather it statistically emerges when a coarse graining average over distances of order, or longer than the Compton wavelength is taken. We also present the modifications necessary to accommodate in our scheme the doubly special relativistic dynamics. In this way, an unsuspected, common statistical origin of the two frameworks is brought to light. Salient issues ...
2011-01-01
International Nuclear Information System (INIS)
Samples from 314 broiler chickens at 2 months age were analyzed for blood serum level of lysozyme and 311 of them were analyzed also for activity of alternative path-way of complement activity (APCA). Chickens were hatched from eggs, irradiated immediately before incubation with different doses of gamma-rays using Rocus M device - group 1 - control (non irradiated), and groups 2, 3 and 4 - irradiated with doses of 0.15, 0.30 and 0.60 Gy, respectively. Lysozyme concentration was highest for the control group, and for the experimental ones it was lower (p<0.001) which is an indication of the strongly negative effect of gamma-rays on this indicator. For APCA the oppsite relationship was observed - increasing of its activity with increasing of irradiation dose (from p<0.05 to p<0.001) which gave reason to suggest that this phenomenon is due to the irradiation. 12 refs., 2 tabs. (author).
The distribution of Lyman-limit absorption systems during and after reionization
Lyman-limit absorption systems can play many important roles during and after cosmological reionization. Unfortunately, due to the prohibitively large dynamic range required, it is impossible to self-consistently include these systems in cosmological simulations. Using fast and versatile semi-numeric simulations, we systematically explore the spatial distribution of absorption systems during and following reionization. We self-calibrate the resulting number of absorbers to the mean free path (mfp) of the ionizing ultraviolet background (UVB), and present results at a given mfp and neutral hydrogen fraction. We use a simple optical depth criterion to identify the locations of absorbers. Our approach is fairly robust to uncertainties such as missing subgrid structure. Unlike at lower redshifts where the UVB is relatively uniform, at higher redshifts the fluctuations in the UVB and the HII morphology of reionization can drive the large-scale distribution of absorption ...
2010-01-01
The Hunt for New Physics at the Large Hadron Collider
The Large Hadron Collider presents an unprecedented opportunity to probe the realm of new physics in the TeV region and shed light on some of the core unresolved issues of particle physics. These include the nature of electroweak symmetry breaking, the origin of mass, the possible constituent of cold dark matter, new sources of CP violation needed to explain the baryon excess in the universe, the possible existence of extra gauge groups and extra matter, and importantly the path Nature chooses to resolve the hierarchy problem - is it supersymmetry or extra dimensions. Many models of new physics beyond the standard model contain a hidden sector which can be probed at the LHC. Additionally, the LHC will be a top factory and accurate measurements of the properties of the top and its rare decays will provide a window to new physics. Further, the LHC could shed light on the origin of neutralino masses if the new physics associated with their generation lies in the TeV ...
2010-01-01
The Holst Spin Foam Model via Cubulations
Spin Foam Models (SFM) are an attempt at a covariant or path integral formulation of canonical Loop Quantum Gravity (LQG). Traditionally, SFM rely on 1. the Plebanski formulation of GR as a constrained BF Theory. 2. simplicial triangulations as a UV regulator and 3. a sum over all triangulations via group field techniques (GFT) in order to get rid off triangulation dependence. Subtle tasks for current SFM are to establish 1. the correct quantum implementation of Plebanski's constraints. 2. the existence of a semiclassical sector implementing additional Regge constraints arising from simplicial triangulations and 3. the physical inner product of LQG via GFT. We propose a new approach which deals with these issues as follows: 1. The simplicity constraints are correctly implemented by starting directly from the Holst action which is also a proper starting point for canonical LQG. 2. Cubulations are chosen rather than triangulations as a regulator. 3. We give a direct ...
2008-01-01
Test Bed for Superconducting Materials
Energy Technology Data Exchange (ETDEWEB)
Superconducting rf cavities are increasingly used in accelerators. Gradient is a parameter of particular importance for the ILC. Much progress in gradient has been made over the past decade, overcoming problems of multipacting, field emission, and breakdown triggered by surface impurities. However, the quenching limit of the surface magnetic field for niobium remains a hard limitation on cavity fields sustainable with this technology. Further exploration of materials and preparation may offer a path to surpassing the current limit. For this purpose, we have designed a resonant test cavity. One wall of the cavity is formed by a flat sample of superconducting material; the rest of the cavity is copper or niobium. The H field on the sample wall is 75% higher than on any other surface. Multipacting is avoided by use of a mode with no surface electric field. The cavity will be resonated through a coupling iris with high-power rf at superconducting temperature until the ...
2006-01-30
Technical Key Figures for Photo-biological Hydrogen Production by Micro-algae
International Nuclear Information System (INIS)
One regenerative path to produce hydrogen is the photo-biological hydrogen production by the green micro-alga Chlamydomonas reinhardtii. This process can be divided into three phases: a growth phase, a phase in which the algae adapt from oxygen production and CO2-fixation to fermentative H2 production, and a phase in which H2 is produced. In a research project carried out at Ruhr-Universitat Bochum, a new developed flat panel bioreactor was investigated. A system analysis was conducted and energetic and environmental key figures were determined. The intention of this assessment on a very early technological stage was to collect first technical data in order to classify the current technological status of the photo-biological H2 production to identify future potentials and to uncover weaknesses. For this reason the key figures were evaluated for the status quo and for two scenarios which allow an outlook on the mid and the long term. The results were compared with ...
2006-06-13
Systems Analysis of Safeguards Effectiveness in a Uranium Conversion Facility
Energy Technology Data Exchange (ETDEWEB)
The U.S. Department of Energy (DOE) is interested in developing tools and methods for potential U.S. use in designing and evaluating safeguards systems. For this goal several DOE National Laboratories are defining the characteristics of typical facilities of several size scales, and the safeguards measures and instrumentation that could be applied. Lawrence Livermore National Laboratory is providing systems modeling and analysis of facility and safeguards operations, diversion path generation, and safeguards system effectiveness. The constituent elements of diversion scenarios are structured using directed graphs (digraphs) and fault trees. Safeguards indicator probabilities are based on sampling statistics and/or measurement accuracies. Scenarios are ranked based on value and quantity of material removed and the estimated probability of non-detection. Significant scenarios, especially those involving timeliness or randomly varying order of events, are transferred ...
2004-06-16
System suitable for use in neutron radiography
Energy Technology Data Exchange (ETDEWEB)
A system for real-time neutron radiography of moving objects is described. It comprise a source adapted to generate a continuous uninterrupted series of neutron pulses. Each pulse has a predetermined peak power and duration compatible with the framing times of a real-time video imaging system. A transporter moves an object to be examined to bring sequentially position selected portions of the object in the path of the pulses. Where the object itself has moving components, pulses are sequentially incident on the object. According to any dissimilarities, the object will alter the intensity of the neutrons passing therethrough. In order to record separately the changes in the neutron intensity, for each pulse, an imager is positioned to receive the neutron beam pulses which have been altered by their passage through the object and produce images indicating intensity alterations. A refrigerated beryllium filter can be used to effectively eliminate thermal neutrons from ...
1990-02-07
System suitable for use in neutron radiography
International Nuclear Information System (INIS)
A system for real-time neutron radiography of moving objects is described. It comprise a source adapted to generate a continuous uninterrupted series of neutron pulses. Each pulse has a predetermined peak power and duration compatible with the framing times of a real-time video imaging system. A transporter moves an object to be examined to bring sequentially position selected portions of the object in the path of the pulses. Where the object itself has moving components, pulses are sequentially incident on the object. According to any dissimilarities, the object will alter the intensity of the neutrons passing therethrough. In order to record separately the changes in the neutron intensity, for each pulse, an imager is positioned to receive the neutron beam pulses which have been altered by their passage through the object and produce images indicating intensity alterations. A refrigerated beryllium filter can be used to effectively eliminate thermal neutrons from ...
1988-07-20
System Analysis for Decay Heat Removal in Lead-Bismuth Cooled Natural Circulated Reactors
Decay heat removal analyses for lead-bismuth cooled natural circulation reactors are described in this paper. A combined multi-dimensional plant dynamics code (MSG-COPD) has been developed to conduct the system analysis for the natural circulation reactors. For the preliminary study, transient analysis has been performed for a 100 MWe lead-bismuth-cooled reactor designed by Argonne National Laboratory (ANL). In addition, decay heat removal characteristics of a 400 MWe lead-bismuth-cooled natural circulation reactor designed by Japan Nuclear Cycle Development Institute (JNC) has been evaluated by using MSG-COPD. PRACS (Primary Reactor Auxiliary Cooling System) is prepared for the JNC's concept to get sufficient heat removal capacity. During 2000 sec after the transient, the outlet temperature shows increasing tendency up to the maximum temperature of 430 Centigrade, because the buoyancy force in a primary circulation path is temporary reduced. However, the ...
2002-07-01
Study of the Photon Strength Functions for Gadolinium Isotopes with the DANCE Array
The gadolinium isotopes are interesting for reactor applications as well as for medicine and astrophysics. The gadolinium isotopes have some of the largest neutron capture cross sections. As a consequence they are used in the control rod in reactor fuel assembly. From the basic science point of view, there are seven stable isotopes of gadolinium with varying degrees of deformation. Therefore they provide a good testing ground for the study of deformation dependent structure such as the scissors mode. Decay gamma rays following neutron capture on Gd isotopes are detected by the DANCE array, which is located at flight path 14 at the Lujan Neutron Scattering Center at Los Alamos National Laboratory. The high segmentation and close packing of the detector array enable gamma-ray multiplicity measurements. The calorimetric properties of the DANCE array coupled with the neutron time-of-flight technique enables one to gate on a specific resonance of a specific isotope in ...
2009-03-10
International Nuclear Information System (INIS)
Active oxygens produced by low-dose irradiation can induce the synthesis of proteins involved in the active oxygen reduction path and can activate the chemical self-defense mechanisms in vivo, which can alleviate the injuries caused by active oxygens themselves. The following findings suggests that it is not only by low-dose irradiation that can induce the responses described above but also by any physical and/or chemical stresses which can produce small amount of active oxygens in vivo. 1. X-irradiation with 0.5 Gy and/or water immersion and restraint induced heat shock protein (HSP)70 in rat stomach cells. HSP70 was also induced in adrenal cells by paraquat administration. 2. The SOD activity in pancreas of rat significantly increased by #gamma#-irradiation with 0.5 Gy. 0.5 Gy irradiation preceeding the alloxan administration significantly suppressed the increase in pancreatic lipid peroxides and in blood glucose levels, degranulation in #beta# cells, and ...
Spherically bent crystal spectroscopy in laser-produced plasma
International Nuclear Information System (INIS)
A curved crystal X-ray spectrographs of reflection type spherical geometry was required based on the Johann scheme. Due to their high efficiency and resolution, X-ray spectrographs of focusing spectrograph spatial resolution are suitable for detecting weak X-ray spectra in spectrometers for laser fusion research. Spherically bent mica crystal with a radius of curvature of 380 mm was used in the spectrometer. The Bragg angle of the crystal analyzer was 51 degree. The image plate was employed to obtain high spatial resolution and a narrow spectral band width, with an effective area of 30 mm x 80 mm. The designed optical path of the X-ray spectrometer beam was 980 mm long from the source to the crystal and the detector. The first experiment was carried out at the 20 J energy laser facility of Research Center of Laser Fusion, China Academy of Engineering Physics. X-ray spectra in an absolute intensity scale were obtained from Al laser-produced plasmas created by laser ...
2008-02-01
Solid oxide fuel cells (Part 2)
Energy Technology Data Exchange (ETDEWEB)
The project has been developing Yttria Stabilized Zirconia (YSZ)-Alumina Composites as an electrolyte of a self-support type planar Solid Oxide Fuel Cell (SOFC) from the following points of view: a path of alumina particles with high thermal conductivity can be designed as an electrolyte sheet; there are some possibilities that the electrolyte can be enhanced in mechanical strength. As previously reported, these composite materials have higher mechanical strength and better thermal shock resistance than those of YSZ. These composites containing 0-30 wt% of Al[sub 2]O[sub 3] were measured by AC impedance method at temperatures of 250-1,000[degree]C. Electrical conductivities of 8YSZ without Al[sub 2]O[sub 3] and a composite consisting of 80 wt% YSZ and 20 wt%Al[sub 2]O[sub 3] as sintered samples were 1.2 x 10[sup -1]S/cm and 1.0 x 10[sup -1]S/cm respectively at 1,000[degree]C. The composite containing 20 wt% of Al[sub 2]O[sub 3] is the most promising candidate ...
1993-01-01
Shielding analysis of TAPP-3,4 end-shield
International Nuclear Information System (INIS)
This paper consists of shielding analysis of steel balls and water filled end shields of Indian Pressurized Heavy Water Reactors (PHWRs). The material composition inside lattice tube is entirely different neutronically as compared with the composition of end-shield. Due to variation of material composition in radial and axial directions and complex geometry, it is necessary to carry out 3-D analysis for reasonable prediction of neutron flux and gamma dose rates. In the present paper, shielding analysis of end-shield for 540 MWe PHWR has been carried out during reactor operating and shutdown conditions using Monte-Carlo code MCNP. Furthermore materials on the periphery and central portion of end shield are different. Therefore the analysis was carried out separately for annular portion and central portion of end shield. The dominating streaming paths through end shields were studied. Predictions compare well with the measurements at TAPS-4 reactor. (author)
2006-11-13
Sensitivity Study for CFD Analysis on Debris Transport to ECCS Sump for CANDU Type Plant in Korea
International Nuclear Information System (INIS)
Once containment recirculation pumps are activated and emergency core cooling (ECC) flow is supplied from the recirculation sump during loss of coolant accident (LOCA), various insulations and coatings on a pipe, equipments and structures damaged by LOCA break jet as well as additional debris sources are transported to recirculation sump screen by the break flow and containment spray flow drainage. This debris may result in loss of net pressure suction head (NPSH) of the recirculation pumps, and have a threat to long term cooling and containment heat removal capacity. In this case, flow patterns of containment pool are important to confirm behaviors of debris transport for predicting various flow paths to the recirculation sump screen. In this paper, models using commercial computational fluid dynamics (CFD) software CFX are developed for containment pool simulation during recirculation mode. The specific plant used for this analysis is CANDU type plant, in Korea
2010-10-01
Energy Technology Data Exchange (ETDEWEB)
The effect of neutralizing cations on the secondary reactions of the primary products from CO hydrogenation over ion-exchanged zeolite-supported Ru catalysts was investigated using zeolites with different alkali cations (Li/sup +/, Na/sup +/, K/sup +/, Rb/sup +/, Cs/sup +/). The transformation of olefins (propylene and butene) on the zeolites without the metal, under conditions similar to those used for CO hydrogenation, was also studied in order to understand the effect of the various constituents of the support, i.e., the Broensted acid sites generated during catalyst preparation and the alkali cations, on possible secondary reactions of the primary olefinic products. It was established that secondary acid-catalyzed reactions of these primary products can play a major role in shaping product selectivity during CO hydrogenation over zeolite-supported catalysts. Depending on the concentration and the strength of the acid sites, various competitive reaction paths ...
1987-10-01
Scaling Laws and Design Principles for Multi-Cellular Wireless OFDMA Systems
In this paper, we consider the downlink of large-scale multi-cellular OFDMA-based networks and study performance bounds of the system as a function of the number of users $K$, the number of base-stations $B$, and the number of resource-blocks $N$. Here, a resource block is a collection of subcarriers such that all such collections, that are disjoint have associated independently fading channels. We derive novel upper and lower bounds on the sum-utility for a general spatial geometry of base stations, a truncated path loss model, and a variety of fading models (Rayleigh, Nakagami-$m$, Weibull, and LogNormal). We also establish the associated scaling laws and show that, in the special case of fixed number of resource blocks, a grid-based network of base stations, and Rayleigh-fading channels, the sum information capacity of the system scales as $\\Theta(B \\log\\log K/B)$ for extended networks, and as $O(B \\log\\log K)$ and $\\Omega(\\log \\log K)$ for dense ...
2011-01-01
Review of the study and application on nuclear forensic analysis
International Nuclear Information System (INIS)
For the interests of national security, many scientists who work in the field of nuclear forensic analysis have carried out extensive work in the past on the detection of radioactive material and attributions study, developed a series of scientific and technical means to trace and detect illicit circulation of nuclear materials used to weapons and other radioactive materials which impair public security. All these questions relate to physical, chemical, biological attribution of materials. The nuclear forensic analysis has already become a special, up-to-date sphere of learning. The goal of the study of nuclear forensics is to prevent terrorists from acquiring not only nuclear weapons but also mate- rials that can be used to make such weapons, including radioactive materials for nuclear power plants, and medical radioisotope to and provide us as many clues of environmental links as possible that could help us trace the smuggling path, to answer the following ...
2009-12-01
International Nuclear Information System (INIS)
The relationship between the current density distribution and the electron density profile during the flat-top phase of Ohmic discharges in TEXTOR has been investigated by means of far-infrared interferometry and polarimetry. It is found that neither gradual nor rapid changes of the electron density distribution (induced by continuous gas feed or pellet injection) alter the current profile significantly. The conclusion is drawn from the temporal evolution of the measured Faraday rotation signals #alpha#_e_x_p(x,t) which are proportional to the line integrals of n_c times the poloidal magnetic field component B_p_c along the probing beam paths (x is the distance of a chord from the plasma centre). By taking into account the known variation of the density profile but keeping the current distribution fixed, theoretical signals #alpha#_s_i_m(x,t) can be calculated which match the observed waveforms very well without any need to readjust the poloidal field. Under ...
Recent neutron scattering work at the University of Lowell
International Nuclear Information System (INIS)
Neutron elastic and inelastic scattering cross sections of _2_3_8U and _2_3_2Th have been measured at the University of Lowell for states below 1.8 MeV. A time-of-flight (TOF) spectrometer was used. The disc-shaped scatterer was oriented to optimize energy resolutions for 200-to-500-keV neutrons. Neutrons were obtained via the _7Li(p,n)_7Be reaction. Targets were prepared by in-situ evaporation of Li onto a Ta backing. During the evaporation, the target thickness was monitored using a 5-m-flight-path TOF spectrometer; a typical target had a neutron thickness from 8 to 10 keV for Esub(p) = 2.25.MeV. Spectra were analyzed using the unfolding code TINA; standard peak shapes were obtained from codes LAGUE and LAPA. Results obtained will be presented.
1981-11-23
Energy Technology Data Exchange (ETDEWEB)
One aspect of the research program SFB 570 'Distortion engineering' is the in situ X-Ray diffraction analysis of phases and residual stresses during complete heat treatment cycles. These investigations result in experimental evidence available for the extensive computations. The optimisation of the instrumentation will be reported. A surface decarburisation of samples made from the ball bearing steel 100Cr6 could be avoided for a temperature range from 800 to 900 C and a holding time of one hour by a combination of evacuate the furnace and using a certain nitrogen flow as protective gas. At lower temperatures small amounts of ferrite caused by an increased diffusion rate of carbon lead again to a surface decarburisation up to a depth of 2 {mu}m. It was proved that with an evacuation of the X-Ray beam path at constant power of the X-Ray source the intensity of diffraction lines could be increased by more than a factor of 4. The use of nitrogen as ...
2007-07-01
Quantum query complexity of minor-closed graph properties
We study the quantum query complexity of minor-closed graph properties, which include such problems as determining whether a graph is planar, is a forest, or does not contain a path of a given length. We show that most minor-closed properties---those that cannot be characterized by a finite set of forbidden subgraphs---have quantum query complexity \\Theta(n^{3/2}). To establish this, we prove an adversary lower bound using a detailed analysis of the structure of minor-closed properties with respect to forbidden topological minors and forbidden subgraphs. On the other hand, we show that minor-closed properties (and more generally, sparse graph properties) that can be characterized by finitely many forbidden subgraphs can be solved strictly faster, in o(n^{3/2}) queries. Our algorithms are a novel application of the quantum walk search framework and give improved upper bounds for several subgraph-finding problems.
2010-01-01
Quantum Transition State Theory for proton transfer reactions in enzymes
We consider the role of quantum effects in the transfer of hyrogen-like species in enzyme-catalysed reactions. This study is stimulated by claims that the observed magnitude and temperature dependence of kinetic isotope effects imply that quantum tunneling below the energy barrier associated with the transition state significantly enhances the reaction rate in many enzymes. We use a path integral approach which provides a general framework to understand tunneling in a quantum system which interacts with an environment at non-zero temperature. Here the quantum system is the active site of the enzyme and the environment is the surrounding protein and water. Tunneling well below the barrier only occurs for temperatures less than a temperature $T_0$ which is determined by the curvature of potential energy surface near the top of the barrier. We argue that for most enzymes this temperature is less than room temperature. For physically reasonable parameters quantum ...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
This paper describes inorganic solid electrolytes from a viewpoint of electrolytes for lithium batteries. Lithium ion conductive inorganic solid electrolytes are largely divided into crystalline and amorphous substances. Crystalline substances are known as LiI and Li3N, and also oxygen acid salt. However, when considering application to a battery, its large grain boundary resistance and electrochemical instability would be a problem. Lithium ion conductive amorphous solid electrolytes are divided into an oxide system and a sulfide system. Since most of them do not contain transition metal elements, they are stable against electrochemical reduction, and ions move isotropically in electrolyte. Therefore, ion conduction paths across the grain boundaries may be connected more easily, forming an electrolyte with low grain boundary resistance. As a result of the efforts of the authors in searching new additives substituting LiI, it was found that addition of Li3PO4 ...
1997-11-05
International Nuclear Information System (INIS)
The leakage behavior of containments beyond design conditions and knowledge of failure modes is required for evaluation of mitigation strategies for severe accidents, risk studies, emergency preparedness planning, and siting. These studies are directed towards assessing the risk and consequences of severe accidents. An accident sequence analysis conducted on a Boiling Water Reactor (BWR), Mark I (MK I), indicated very high temperatures in the dry-well region, which is the location of the majority of electrical penetration assemblies. Because of the high temperatures, it was postulated in the ORNL study that the sealants would fail and all the electrical penetration assemblies would leak before structural failure would occur. Since other containments had similar electrical penetration assemblies, it was concluded that all containments would experience the same type of failure. The results of this study, however, show that this conclusion does not hold for PWRs because in the worst ...
Performance of bentonite/crushed rock borehole plugs
International Nuclear Information System (INIS)
A mixture of crushed rock and bentonite is being considered as backfill and sealant for high-level nuclear waste repositories. Many variables affect the hydraulic conductivity of such a mixture, including the size and shape of the rock particles, method of mixing, water content and density of the clay, and the weight ratio of rock to clay. Mixtures of crushed basalt and bentonite have been tested to determine the relative effects of these variables. Two types of permeameters are used, 20 cm diameter stainless steel permeameters and 10 cm diameter clear PVC permeameters. Plugs are installed as a single lift or in many lifts; the water content of the clay ranged from air-dry (in most cases) to as high as 200%. Preliminary results show that a mixture of 75% crushed basalt and 25% bentonite has a hydraulic conductivity between 1 x 10/sup -9/ cm/s and 2.5 x 10/sup -8/ cm/s. In some cases, preferential flow paths have developed (possibly as a result of the ...
Parametric Resonance Ionization Cooling and Reverse Emittance Exchange for Muon Collider
Energy Technology Data Exchange (ETDEWEB)
Two methods to cool muon beams deeply below the limit conventionally established for the ionization cooling are proposed. In Phase Ionization Cooling (PIC), the beam is focused at wedge absorber plates each half of particle oscillation period by imposing a weak parametric resonance along the beam path. The resonance growth of particle amplitude is surmounted by the ionization cooling. At optimum, such arrangement results in reduction of each of two transverse emittances by an order of value in addition to the preceding 6D ionization cooling. Next, resonance focusing and transverse cooling can be continued in the regime of a fast Reverse Emittance Exchange (REMEX). Here, the sign of the absorber wedge is opposite to PIC while the dispersion increased. REMEX to be accompanied by the bunch lengthening and acceleration in order to maintain the relative energy spread at an appropriate level. The limitations due to energy straggling in absorber will be evaluated, and ...
2005-09-18
Packet Drop Avoidance for High-speed network transmission protocol
Energy Technology Data Exchange (ETDEWEB)
As network bandwidth continues to grow and longer paths are used to exchange large scientific data between storage systems and GRID computation, it has become increasingly obvious that there is a need to deploy a packet drop avoidance mechanism into network transmission protocols. Current end-to-end congestion avoidance mechanisms used in Transmission Control Protocol (TCP) have worked well on low bandwidth delay product networks, but with newer high-bandwidth delay networks they have shown to be inefficient and prone to unstable. This is largely due to increased network bandwidth coupled with changes in internet traffic patterns. These changes come from a variety of new network applications that are being developed to take advantage of the increased network bandwidth. This paper will examine the end-to-end congestion avoidance mechanism and perform a step-by-step analysis of its theory. In addition we will propose an alternative approach developed as part of a new ...
2004-05-01
PICTURE: an interactive tool for creating visual aids. Reference manual, version 2. 0
Energy Technology Data Exchange (ETDEWEB)
The PICTURE utility generates user defined pictures with black-and-white or color output, suitable for viewgraphs, slides, report diagrams - in general, any application requiring visual aids. The interactive menu-driven system allows a user to create a picture consisting of text, straight lines, graphs, and assortment of markers, splines and drawings, all in a variety of colors. Commands for manipulating the picture include moving, scaling, rotating, deleting, copying and changing the color of objects. Text strings may be aligned left, right, or centered, and have a vertical or horizontal path. Markers, circles and the large bold font may be filled or unfilled. The user may add or delete one of two overlay grids for help in positioning items. The final product may be saved in a text file for later retrieval. PICTURE currently runs on a VAX 11/780 with the DI-3000 commercial graphics package. Supported graphics devices include Ramtek 9400 and Metheus 440 frame ...
1984-01-20
International Nuclear Information System (INIS)
The natural circulation experiments were conducted to confirm the cooling capability and the flow characteristics of the natural convection in the HANARO (Hi-flux Advanced Neutron Application Reactor). The tests were done at the power levels of 2%, 3% and 4% (1.2MW_t_h) of full power. The flow rates and temperatures at various locations of the primary and secondary cooling loops were measured at each power level. The temperature distributions in the chimney and the pool were also obtained. Through tests, the flow paths of the natural circulation and the cooling capability of the reactor were confirmed as designed. In addition, the simulation for the natural circulation tests was made by using RELAP5/KMRR, which was modified from RELAP5/MOD2 for applying to the HANARO conditions. The simulation results show that RELAP5/KMRR gives reasonable predictions for the flow rate and the coolant temperature during natural circulation condition in the HANARO. (author)
OECD/NEA international Stripa project 1980-1992. Overview volume 3
International Nuclear Information System (INIS)
The broad objective of the engineered barriers studies was to demonstrate and qualify the use of different materials and techniques for sealing water flow paths in the Stripa granite, the mine excavations and the excavation disturbed zones. As may be anticipated from the application of the observational method that forms the basis for design of geotechnical structures, the programme evolved with the finding being made at Stripa and other underground laboratories. During phase 1, the engineered barriers investigations focussed on the heat affected zone of the repository. Specifically, the response of clay buffers and the interactions between waste containers, clay buffer materials and the rock were studied. The phase 2 investigations examined the feasibility of sealing boreholes shafts and tunnels with clay sealants. The phase 3, studies of the ability to grout and seal fractured granite including the excavation disturbed zone were effected and specific studies into ...
Numerical analysis of erosion of the rotor labyrinth seal in a geothermal turbine
Energy Technology Data Exchange (ETDEWEB)
Excessive erosion of the labyrinth seal of a 100 MW geothermal turbine has been investigated. This study used computational fluid dynamics (CFD) and aims to identify one cause of erosion and a possible solution for substantially reducing it. The predictions were based upon a numerical calculation using a CFD model of the labyrinth seal with a water/steam flow containing hard solid particles and solved with a commercial CFD code: Fluent V5.0. The results confirmed the existence of flow conditions that play a major role in the rotor labyrinth seal erosion. Afterwards, the flow path was simulated with changes of rotor labyrinth seal geometry, which are indeed feasible of being implemented. The results confirmed that it is possible to reduce the erosion process by approximately 80% by incorporating a steam flow deflector in the fourth stage diaphragm, which changes the steam flow direction in the inlet zone to the rotor labyrinth seal channel, resulting in a reduction ...
2002-10-01
New horizons of zeolite supported catalysts
International Nuclear Information System (INIS)
This paper reports on the superiority of zeolites over amorphous solids which is well documented for solid acid catalysts of industrial use. Crystalline supports, likewise, open attractive perspectives for catalysis by metals, alloys, and ligated metal clusters. Size and location of clusters can be controlled by careful design of the preparation conditions. Pore dimensions control the access of reactants to active sites and escape paths for products. Cage dimensions determine which transition states can be attained; window apertures are functional in isolating metal clusters from each other, thus preventing ther coalescence and growth. The ship-in-a-bottle method permits deisgn of fairly large active complexes entrapped in zeolite cages. Orientation of non-spherical molecules in a zeolite proe helps to direct their collision with a metal particle to the head on mode; however, isolated Pt atoms hidden in niches of the pore walls can attack passing molecules at their ...
1992-04-05
Multipass laser mass spectrometer with extreme jet-cooled pulsed gas
International Nuclear Information System (INIS)
We have developed a photon accumulated laser mass spectrometer that enables us to identify isomers of polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran. This system is comprised of a high temperature (230 deg. C) pulsed gas injector (PGI), multimirror multipath system (MMS), and the conventional time-of-flight mass spectrometer. The PGI induces the formation of a choked supersonic jet gas pulse that cools down to a temperature to restrain fragmentation and reduces vibrational and rotational thermal noises. The results suggest that the excited lifetime numbers and fragment dynamics of these species change completely with jet cooling of molecules. The MMS enhances the soft ionization efficiency (by a factor of 1000 over a single path system) through photon accumulation by extending the irradiation duration (to about 40 ns) and volume, and it further minimizes fragmentation by carefully controlling the laser intensity distribution within the ionization ...
2006-09-01
International Nuclear Information System (INIS)
We investigate some aspects of the radiation damage mechanisms in biomolecules, focusing on the modelling of resonant fragmentation caused by the attachment of low-energy electrons (LEEs) initially ejected by biological tissues when exposed to ionizing radiation. Scattering equations are formulated within a symmetry-adapted, single-center expansion of both continuum and bound electrons, and the interaction forces are obtained from a combination of ab initio calculations and a nonempirical model of exchange and correlation effects developed in our group. We present total elastic scattering cross-sections and resonance features obtained for the equilibrium geometries of glycine, alanine, proline and valine. Our results at those geometries of the target molecules are briefly shown to qualitatively explain some of the fragmentation patterns obtained in experiments. We further carry out a one-dimensional (1D) modeling for the dynamics of intramolecular energy transfers mediated by the ...
2010-10-01
Measurement of the antiproton/proton ratio at few-TeV energies with the ARGO-YBJ experiment
Cosmic ray antiprotons provide an important probe for the study of cosmic-ray propagation in the interstellar space and to investigate the existence of Galactic dark matter. Cosmic rays are hampered by the Moon, therefore a deficit of cosmic rays in its direction is expected (the so-called "Moon shadow"). The Earth-Moon system acts as a magnetic spectrometer. In fact, due to the geomagnetic field the center of the Moon shifts westward by an amount depending on the primary cosmic ray energy. Paths of primary antiprotons are therefore deflected in an opposite sense in their way to the Earth. This effect allows, in principle, the search of antiparticles in the opposite direction of the observed Moon shadow. The ARGO-YBJ experiment, in stable data taking since November 2007 with an energy threshold of a few hundreds of GeV, is observing the Moon shadow with high statistical significance. Using about 1 year data, an upper limit of the antip/p flux ratio in the few-TeV ...
2009-01-01
Measurement of the /SUP 242m/ Am neutron fission cross section
Energy Technology Data Exchange (ETDEWEB)
The fission cross section of /SUP 242m/ Am has been measured from 0.005 eV to 20 MeV using time-of-flight techniques at the Oak Ridge Electron Linear Accelerator. A hemispherical plate fission ionization chamber with five pairs of plates contained three deposits totaling 507 ..mu..g of /SUP 242m/ Am, one deposit of 168 ..mu..g /sup 235/U, and a ''weightless'' deposit of /sup 252/Cf, which served as a monitor of chamber performance. The fission of /sup 235/U, served as the cross-section standard for energies above 101 keV while /sup 6/Li(n,..cap alpha..), normalized to /sup 235/U fission in the 7.8- to 11.0-eV interval, served as a shape standard below 101 keV. Approximately 360 h of data were obtained at a flight path distance of 9.1 m, primarily with 40-ns bursts. Particular attention was paid to correction of backgrounds, especially inscattered-neutron-induced events. The fission resonance integral was found to be 1800 + or - ...
1983-05-01
Measurement of the /SUP 242m/ Am neutron fission cross section
International Nuclear Information System (INIS)
The fission cross section of /SUP 242m/ Am has been measured from 0.005 eV to 20 MeV using time-of-flight techniques at the Oak Ridge Electron Linear Accelerator. A hemispherical plate fission ionization chamber with five pairs of plates contained three deposits totaling 507 #mu#g of /SUP 242m/ Am, one deposit of 168 #mu#g "2"3"5U, and a ''weightless'' deposit of "2"5"2Cf, which served as a monitor of chamber performance. The fission of "2"3"5U, served as the cross-section standard for energies above 101 keV while "6Li(n,#alpha#), normalized to "2"3"5U fission in the 7.8- to 11.0-eV interval, served as a shape standard below 101 keV. Approximately 360 h of data were obtained at a flight path distance of 9.1 m, primarily with 40-ns bursts. Particular attention was paid to correction of backgrounds, especially inscattered-neutron-induced events. The fission resonance integral was found to be 1800 + or - 65 b.
Lyman-alpha emitters as tracers of the transitioning Universe
Of the many ways of detecting high redshift galaxies, the selection of objects due to their redshifted Ly-alpha emission has become one of the most successful. But what types of galaxies are selected in this way? Until recently, Ly-alpha emitters were understood to be small star-forming galaxies, possible building-blocks of larger galaxies. But with increased number of observations of Ly-alpha emitters at lower redshifts, a new picture emerges. Ly-alpha emitters display strong evolution in their properties from higher to lower redshift. It has previously been shown that the fraction of ultra-luminous infrared galaxies (ULIRGs) among the Ly-alpha emitters increases dramatically between redshift three and two. Here, the fraction of AGN among the LAEs is shown to follow a similar evolutionary path. We argue that Ly-alpha emitters are not a homogeneous class of objects, and that the objects selected with this method reflect the general star forming and active galaxy ...
2011-01-01
Keynote address. Division 1. Energy and economic development
Energy Technology Data Exchange (ETDEWEB)
This paper was presented at the opening plenary session. As the end of the century approaches, environmental protection is one of the most significant global issues which will shape our energy path and economic development pattern. In face of environmental challenges, we will have to take into account environmental factors in the economic development process itself. This requires the pursuit of sustainable economic development, a process which may involve strengthened energy conservation, improved efficiency and switching to less carbon intensive energy sources. Energy inefficiency, technological scarcity and financial vulnerability in developing countries may best be resolved by changing their economic and market structures to facilitate relevant investments. However, effective reform of the energy industry in developing economies and economies in transition will also require international cooperation in terms of transfer of technology, capital, know-how and ...
1995-12-31
Insertion Loss of Personal Protective Clothing
Energy Technology Data Exchange (ETDEWEB)
'The use of personal protective clothing that covers the head is a common practice in many industries. Such personal protective clothing will impact the sound pressure level and the frequency content of sounds to which the wearer will be exposed. The use of such clothing, then, may impact speech and alarm audibility. A measure of the impact of such clothing is its insertion loss. Insertion loss measurements were performed on four types of personal protective clothing in use by Westinghouse Savannah River Company personnel which utilize cloth and plastic hood configurations to protect the head. All clothing configurations tested at least partially cover the ears. The measurements revealed that insertion loss of the items tested was notable at frequencies above 1000 Hz only and was a function of material stiffness and acoustic flanking paths to the ear. Further, an estimate of the clothing''s noise reduction rating reveals poor performance ...
1999-05-13
In situ remediation of uranium contaminated groundwater
Energy Technology Data Exchange (ETDEWEB)
In an effort to develop cost-efficient techniques for remediating uranium contaminated groundwater at DOE Uranium Mill Tailing Remedial Action (UMTRA) sites nationwide, Sandia National Laboratories (SNL) deployed a pilot scale research project at an UMTRA site in Durango, CO. Implementation included design, construction, and subsequent monitoring of an in situ passive reactive barrier to remove Uranium from the tailings pile effluent. A reactive subsurface barrier is produced by emplacing a reactant material (in this experiment various forms of metallic iron) in the flow path of the contaminated groundwater. Conceptually the iron media reduces and/or adsorbs uranium in situ to acceptable regulatory levels. In addition, other metals such as Se, Mo, and As have been removed by the reductive/adsorptive process. The primary objective of the experiment was to eliminate the need for surface treatment of tailing pile effluent. Experimental design, and laboratory and field ...
1997-02-01
Energy Technology Data Exchange (ETDEWEB)
Westinghouse is currently conducting the pre-application licensing of the International Reactor Innovative and Secure (IRIS). One of the key aspects of the IRIS design is its safety-by-designTM philosophy and within this framework the PRA is being used as an integral part of the design process. The most ambitious risk-related goal for IRIS is to reduce the Emergency Planning Zone (EPZ) to within the exclusion area by demonstrating that the off-site doses are consistent with the US Protective Action Guidelines (PAGs) for initiation of emergency response so that the required protective actions would be limited to the exclusion area. As a first step, a model has been developed to provide a first order approximation of the Large Early Release Frequency (LERF) as a surrogate predictor of the off-site doses. A key-aspect of the LERF model development is the characterization of the possible paths of release. Four main categories have been historically pointed out: (1) ...
2004-10-06
Heavy water reactor facility large-scale containment cooling test program
The Heavy Water Reactor Facility (HWRF), as part of the defense-in-depth philosophy to mitigate the effect of design-basis and severe accidents, is equipped with a passive containment cooling system (PCCS). The function of the PCCS is to provide a safety-grade path to the ultimate heat sink for the removal of the reactor coolant system sensible heat and core decay heat. Ambient air enters an annular space between the steel containment shell and the surrounding concrete shield building through inlets in the shield building wall, is heated via natural convection, rises, and exits the building through a chimney located above the containment dome. A test program is in place to access parameters important to the effective operation of the PCCS. This paper focuses on the large-scale tests (LSTs). The objectives of these tests are as follows: (1) demonstrate natural circulation cooling with more prototypic cylinder and dome surface area ratios than were available in the ...
1992-01-01
Heavy water reactor facility large-scale containment cooling test program
International Nuclear Information System (INIS)
The Heavy Water Reactor Facility (HWRF), as part of the defense-in-depth philosophy to mitigate the effect of design-basis and severe accidents, is equipped with a passive containment cooling system (PCCS). The function of the PCCS is to provide a safety-grade path to the ultimate heat sink for the removal of the reactor coolant system sensible heat and core decay heat. Ambient air enters an annular space between the steel containment shell and the surrounding concrete shield building through inlets in the shield building wall, is heated via natural convection, rises, and exits the building through a chimney located above the containment dome. A test program is in place to access parameters important to the effective operation of the PCCS. This paper focuses on the large-scale tests (LSTs). The objectives of these tests are as follows: (1) demonstrate natural circulation cooling with more prototypic cylinder and dome surface area ratios than were available in the ...
1992-11-15
Graphite Technology Development Plan
Energy Technology Data Exchange (ETDEWEB)
This technology development plan is designed to provide a clear understanding of the research and development direction necessary for the qualification of nuclear grade graphite for use within the Next Generation Nuclear Plant (NGNP) reactor. The NGNP will be a helium gas cooled Very High Temperature Reactor (VHTR) with a large graphite core. Graphite physically contains the fuel and comprises the majority of the core volume. Considerable effort will be required to ensure that the graphite performance is not compromised during operation. Based upon the perceived requirements the major data needs are outlined and justified from the perspective of reactor design, reatcor performance, or the reactor safety case. The path forward for technology development can then be easily determined for each data need. How the data will be obtained and the inter-relationships between the experimental and modeling activities will define the technology development for graphite ...
2007-09-01
Global interrupt and barrier networks
Energy Technology Data Exchange (ETDEWEB)
A system and method for generating global asynchronous signals in a computing structure. Particularly, a global interrupt and barrier network is implemented that implements logic for generating global interrupt and barrier signals for controlling global asynchronous operations performed by processing elements at selected processing nodes of a computing structure in accordance with a processing algorithm; and includes the physical interconnecting of the processing nodes for communicating the global interrupt and barrier signals to the elements via low-latency paths. The global asynchronous signals respectively initiate interrupt and barrier operations at the processing nodes at times selected for optimizing performance of the processing algorithms. In one embodiment, the global interrupt and barrier network is implemented in a scalable, massively parallel supercomputing device structure comprising a plurality of processing nodes interconnected by multiple ...
2008-10-28
Energy Technology Data Exchange (ETDEWEB)
A gas-fired boiler plant comprises a burner bed extending over a flat surface and heat exchanger pipes arranged above the burner bed, parallel to the said surface. The heat exchanger tubes comprise pipes equipped with a pluraltiy of flat ribs which extend substantially radially from the said pipes and which are provided in space arrangement over the length of the said heat exchanger pipes. The ribs are provided with bent-off portions. The hot flue gases rising from the burner bed flow through the gaps formed between the said ribs and pipes. In order to improve both the convective heat transmission and the utilization of the radiant heat, the bent-over edges are inclined, at least partly, relative to the surface of said burner bed, the arrangement being selected in a manner to ensure that bent-over portions point towards the burner bed and the rising flue gased are guided around the pipes along a roughly semi-circular path.
1989-10-10
GENERAL REQUIREMENTS FOR SIMULATION MODELS IN WASTE MANAGEMENT
Most waste management activities are decided upon and carried out in a public or semi-public arena, typically involving the waste management organization, one or more regulators, and often other stakeholders and members of the public. In these environments, simulation modeling can be a powerful tool in reaching a consensus on the best path forward, but only if the models that are developed are understood and accepted by all of the parties involved. These requirements for understanding and acceptance of the models constrain the appropriate software and model development procedures that are employed. This paper discusses requirements for both simulation software and for the models that are developed using the software. Requirements for the software include transparency, accessibility, flexibility, extensibility, quality assurance, ability to do discrete and/or continuous simulation, and efficiency. Requirements for the models that are developed include traceability, ...
2003-02-27
Focused ion beam techniques for fabricating geometrically-complex components and devices.
Energy Technology Data Exchange (ETDEWEB)
We have researched several new focused ion beam (FIB) micro-fabrication techniques that offer control of feature shape and the ability to accurately define features onto nonplanar substrates. These FIB-based processes are considered useful for prototyping, reverse engineering, and small-lot manufacturing. Ion beam-based techniques have been developed for defining features in miniature, nonplanar substrates. We demonstrate helices in cylindrical substrates having diameters from 100 {micro}m to 3 mm. Ion beam lathe processes sputter-define 10-{micro}m wide features in cylindrical substrates and tubes. For larger substrates, we combine focused ion beam milling with ultra-precision lathe turning techniques to accurately define 25-100 {micro}m features over many meters of path length. In several cases, we combine the feature defining capability of focused ion beam bombardment with additive techniques such as evaporation, sputter deposition and electroplating in order to ...
2004-03-01
First direct mass measurement of the proton rich nuclides {sup 85,86,87}Mo and {sup 87}Tc
Energy Technology Data Exchange (ETDEWEB)
The masses of proton rich nuclides in the vicinity of N=Z=43 were measured with the Penning trap mass spectrometer SHIPTRAP at GSI. These nuclei were produced in the fusion-evaporation reaction {sup 36}Ar+{sup 54}Fe at energies of 5.0 and 5.9 MeV/u and separated at the velocity filter SHIP. The data are of astrophysical interest since these nuclei are believed to be a part of the rp and {nu}p process paths. The masses of {sup 85}Mo and {sup 87}Tc were measured for the first time. The masses of another two nuclides, {sup 86,87}Mo, were determined for the first time in a direct mass measurement. For these nuclides the mass excess deviates from values of the 2003 Atomic Mass Evaluation by up to 1.5 MeV, indicating a systematic shift of the mass surface in this region of the nuclear chart. Additionally, the masses of {sup 86}Zr and {sup 85}Nb were measured and found to be in agreement with the values obtained at JYFLTRAP. The experiment as well as preliminary data on ...
2009-07-01
First direct mass measurement of the proton rich nuclides "8"5","8"6","8"7Mo and "8"7Tc
International Nuclear Information System (INIS)
The masses of proton rich nuclides in the vicinity of N=Z=43 were measured with the Penning trap mass spectrometer SHIPTRAP at GSI. These nuclei were produced in the fusion-evaporation reaction "3"6Ar+"5"4Fe at energies of 5.0 and 5.9 MeV/u and separated at the velocity filter SHIP. The data are of astrophysical interest since these nuclei are believed to be a part of the rp and #nu#p process paths. The masses of "8"5Mo and "8"7Tc were measured for the first time. The masses of another two nuclides, "8"6","8"7Mo, were determined for the first time in a direct mass measurement. For these nuclides the mass excess deviates from values of the 2003 Atomic Mass Evaluation by up to 1.5 MeV, indicating a systematic shift of the mass surface in this region of the nuclear chart. Additionally, the masses of "8"6Zr and "8"5Nb were measured and found to be in agreement with the values obtained at JYFLTRAP. The experiment as well as preliminary data on mass values, separation ...
2009-03-16
First RAVEN flight set for September
Energy Technology Data Exchange (ETDEWEB)
An unmanned aerial vehicle called RAVEN, said to be capable of remote tracking of onshore and offshore oil and gas facilities, has been developed by a group of graduate students from Memorial University of Newfoundland. RAVEN is claimed to be capable of performing a number of tasks under its own control without the need for human intervention, including checking onshore pipelines for damage, or scouting the path of hazardous icebergs offshore. The RAVEN was created to meet the need for real time iceberg tracking and early hazard detection, supplementing or replacing the present method of RADARSAT images and tracking by manned aircraft. The RAVEN can be launched from any platform; it can fly under conditions that would be too dangerous for a manned aircraft. Currently in the prototype stage, the first trial flight for the RAVEN is expected to take place in September 2002. The first flight will consist of five GPS waypoints set relatively close together in a pattern ...
2002-08-01
Energy Technology Data Exchange (ETDEWEB)
Perforated thermoplastic masks are used to provide patients immobilization. This procedure inserts a material in the path of the radiation beam, that attenuates and modifies the beam fluence and flatness. The present study evaluates the increase in skin dose as a result of using thermoplastic masks. Relative doses were measured on the surface of a solid water phantom, in the presence and absence of masks. These masks were stretched according to deformation patterns observed in clinical routine. The measurements were obtained with a plane-parallel chamber (Markus type 23343) and radiochromic film (EBT Gafchromic) for 6MV X-rays from a linear accelerator, and for a radiation beam from a cobalt therapy unit. The results showed that thermoplastic masks, whose thickness varied between 2 and 3 mm, increased the dose on the surface by a factor of 3. Due to the variations in the skin dose distribution, clinical procedures were suggested to minimize radiobiological damages ...
2010-07-01
Evaluation of the increase of superficial dose due to thermoplastic immobilizing in radiotherapy
International Nuclear Information System (INIS)
Perforated thermoplastic masks are used to provide patients immobilization. This procedure inserts a material in the path of the radiation beam, that attenuates and modifies the beam fluence and flatness. The present study evaluates the increase in skin dose as a result of using thermoplastic masks. Relative doses were measured on the surface of a solid water phantom, in the presence and absence of masks. These masks were stretched according to deformation patterns observed in clinical routine. The measurements were obtained with a plane-parallel chamber (Markus type 23343) and radiochromic film (EBT Gafchromic) for 6MV X-rays from a linear accelerator, and for a radiation beam from a cobalt therapy unit. The results showed that thermoplastic masks, whose thickness varied between 2 and 3 mm, increased the dose on the surface by a factor of 3. Due to the variations in the skin dose distribution, clinical procedures were suggested to minimize radiobiological damages ...
2010-08-18
Energy-resolved electron particle and energy fluxes in positive column plasmas
Energy Technology Data Exchange (ETDEWEB)
This paper deals with electron flux densities and electron energy flux densities in positive column discharges. Recent kinetic calculations by Uhrlandt and Winkler have revealed the interesting physical phenomenon of radially inward directed energy flux densities in positive column plasmas. We have used a self-consistent positive column model, based on an accurate and highly detailed Monte Carlo code, to study this effect in more depth. The results of this study show a rather complex physical picture of electron particle and energy flux densities. Electrons with low energies usually exhibit radially outward directed particle and energy flux densities. At energies above the threshold for electronic excitation particle and energy flux densities are usually inward directed. Only close to the wall, at total energies above the wall potential energy, do these flux densities point towards the wall. The thickness of this 'wall loss region' scales with the electron ...
1999-11-07
Electromagnetic levitation system: an experiment approach
International Nuclear Information System (INIS)
In this paper, we propose a simple method for controlling an electromagnetic levitation (Mag lev) system. The model of the Mag lev system under consideration in this paper is third order, inherently nonlinear and unstable. For designing a controller to obtain a good disturbance rejection and being insensitive to parameter variations, we use an inner-loop and an outer-loop configuration. The configuration is the key to solve this problem. By using a nonlinear state transformation in the feedback path, a cascaded PI controller and a redefined input in the inner loop, we obtain a linear second order system. Furthermore, to achieve a stable system with a good disturbance rejection, we design a Pid controller cascaded with the inner loop system in the negative unity feedback configuration in the outer loop. We show that the closed-loop system is robustly stabilized against the mass variation. Simulation results show that despite actuator saturation limits, the ...
1999-05-17
Effect of velocity variation on secondary-ion-emission probability: Quantum stationary approach
Energy Technology Data Exchange (ETDEWEB)
The ion-velocity dependence of the ionization probability for an atom ejected from a surface is examined by using a quantum approach in which the coupled motion between electrons and the outgoing nucleus is followed along the whole trajectory by solving the stationary Schroedinger equation. We choose a very-small-cluster-model system in which the motion of the atom is restricted to one dimension, and with energy potential curves corresponding to the involved channels varying appreciably with the atom position. We found an exponential dependence on the inverse of the asymptotic ion velocity for high emission energies, and a smoother behavior with slight oscillations at low energies. These results are compared with those obtained within a dynamical-trajectory approximation using either a constant velocity equal to the asymptotic ionic value, or expressions for the velocity derived from the eikonal approximation and from the classical limit of the current vector. Both approaches give ...
1989-11-01
Energy Technology Data Exchange (ETDEWEB)
The leakage current behaviors of PLZT capacitors with top electrodes of Pt, Ir, and IrO{sub 2} are investigated before and after hydrogen forming gas anneal. The P-E hysteresis and fatigue properties of Pt/PLZT/Pt capacitors are almost recovered after recovery anneal in O{sub 2} ambient. The leakage current mechanisms of PLZT capacitors with Pt and IrO{sub 2} top electrodes are consistent with space-charge influenced injection model showing the strong time dependence irrespective of annealing conditions. On the other hand, the leakage current behavior of Ir/PLZT/Pt capacitor shows steady state independent of time because IrPb, conducting phase, formed at interface between Ir top and PLZT is a high conduction path. Teh leakage current mechanism of Ir/PLZT/Pt capacitor is consistent with Schottky barrier model. (author). 15 refs., 6 figs.
2001-02-01
ELECTROMAGNETIC CALORIMETER (ECAL)
ECAL Barrel (EB) As already mentioned in June, the Barrel ECAL is fully commissioned and routinely used during CRUZET runs. Good progress has been made in the last months to ensure a stable and fully reliable operation, in particular for the Trigger path. More details can be found in the DPG report in this bulletin. ECAL Endcaps (EE) In the June CMS bulletin, it had been announced that the Dee’s mechanical assembly had been finished end of May. However the electronics integration was still going on for the first Dee. The Summer has seen a spectacular breakthrough of the Endcap project. The electronics integration of Dee1 was completed early July, and this first Dee was transported to point 5 on July 8th. The completion of the three other Dees followed at a pace of one per week. In all cases the quality of the detector as measured in the assembly center was excellent, with all channels active and the expected ...
Diverter/bop system and method for a bottom supported offshore drilling rig
Energy Technology Data Exchange (ETDEWEB)
This patent describes a system adapted for alternative use as a diverter or a blowout preventer for a bottom supported drilling rig and adapted for positioning beneath a rotary table of the drilling rig, the system comprising: a fluid flow controller having a controller housing with a lower opening and an upper opening and a vertical flow path therebetween and an outlet passage provided in its housing wall, and at least two bases. A method is described for installing a system adapted for alternative connection as a diverter or a blowout preventer for a bottom supported drilling rig positioned beneath a rotary table of the drilling rig after structural casing has been set in a borehole. The method comprises: positioning a first telescoping spool having a lower end and an upper end below the rotary table, the first spool having a first base disposed at its upper end, the first base having a port disposed in its wall; aligning a fluid flow controller having a ...
1987-03-03
Energy Technology Data Exchange (ETDEWEB)
The usual method of introducing engineers to the concept of dislocations and their role in plastic flow is to compare an estimate of the theoretical strength of solid (of order {micro}/30 where {micro} is the shear modulus) and the observed strength of either single crystals ({mu}/10{sup 4}) or practical engineering material such as structural steels where the yield stress in shear is of order {mu}/10{sup 3}. However, if one considers the problem in reverse, one can consider the accumulation of dislocations as an important mechanism by which one can produce engineering materials in which the strength level approaches the theoretical strength. If one assumes that the flow stress can be expressed in terms of te mean free path between stored dislocations or as the square root of the global dislocation density, then one can see the influence of dislocation density in a diagrammatic form. It is clear that the strengthening by dislocation accumulation due to large ...
1999-04-01
Energy Technology Data Exchange (ETDEWEB)
This report describes a study to evaluate methods for locating leaks of dielectric fluid from buried high-voltage cable systems. Two primary types of leak location systems were investigated: (1) systems that will rapidly isolate the leak within a manhole section, typically 1000-m long on a feeder that might be 30-km long; and (2) systems that will then pinpoint the location of the leak. Rapid leak isolation was accomplished by developing an enhanced conductivity oil probe which allows the injection of a small quantity of conductive oil and which indicates the path of the oil as it drifts downstream in the direction of the leak. Two methods for pinpointing the leak were proven. The more successful method was the use of trained leak location dogs which were found to have far better sensitivity than instruments and which could detect cable oil alone without the need for additives. A tracer gas injection and detection scheme was developed for use in areas where the ...
1982-10-01
We study the emission zone in a single-layer polymer light-emitting diode. The emission zone is found by studying the angular distribution of the electroluminescence. The emission is modeled by accounting for optical interference. We account for birefringence of the anode layer in our model. The active polymer was, however, found to be isotropic. The anode consists of a single-layer of the conducting polymer complex poly(3,4-ethylenedioxythiophene) and poly(styrene sulfonate) (PEDOT-PSS), with enhanced conductivity. As a cathode we use plain aluminum. By using only PEDOT-PSS we avoid having a thin metal layer or indium-tin-oxide as the anode in the path of the escaping light. The active material is a substituted polythiophene with excellent film forming properties. A comparison between the experimental and calculated angular distribution of light emission from a single-layered polymer light-emitting diode was shown to be in good agreement for the spectral region ...
2001-06-01
DOE/NORA/BNL oil heat research agenda development
Energy Technology Data Exchange (ETDEWEB)
The National Oilheat Research Alliance (NORA) has been formed and is currently working to establish a Congressionally approved oilheat check-off program to provide funding for research, education, training, safety, and marketing to benefit the US oilheat industry. NORA will be presenting this program to the Congress for its consideration and approval in the coming year. It will follow the same path as the National Propane Gas Association which is currently working on obtaining Congressional approval of a propane check off program that has already attracted over 120 cosponsors in the House of representatives. An effort to define the basis of a joint US Department of Energy (DOE) and Oilheat industry (marketers) program for future oilheat equipment research and development will be conducted during FY-1996. At the request of NORA representatives BNL will coordinate the development of a research agenda addressing three categories of activities, research appropriate for ...
1996-07-01
Cybercars Past, Present and Future of the Technology
Automobile has become the dominant transport mode in the world in the last century. In order to meet a continuously growing demand for transport, one solution is to change the control approach for vehicle to full driving automation, which removes the driver from the control loop to improve efficiency and reduce accidents. Recent work shows that there are several realistic paths towards this deployment : driving assistance on passenger cars, automated commercial vehicles on dedicated infrastructures, and new forms of urban transport (car-sharing and cybercars). Cybercars have already been put into operation in Europe, and it seems that this approach could lead the way towards full automation on most urban, and later interurban infrastructures. The European project CyberCars has brought many improvements in the technology needed to operate cybercars over the last three years. A new, larger European project is now being prepared to carry this work further in order to ...
2005-01-01
Crushed Salt Constitutive Model
Energy Technology Data Exchange (ETDEWEB)
The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the model -- one for the shear consolidation tests and one for a combination of the shear and hydrostatic consolidation tests. ...
1999-02-01
Computing Good Nash Equilibria in Graphical Games
This paper addresses the problem of fair equilibrium selection in graphical games. Our approach is based on the data structure called the {\\em best response policy}, which was proposed by Kearns et al. \\cite{kls} as a way to represent all Nash equilibria of a graphical game. In \\cite{egg}, it was shown that the best response policy has polynomial size as long as the underlying graph is a path. In this paper, we show that if the underlying graph is a bounded-degree tree and the best response policy has polynomial size then there is an efficient algorithm which constructs a Nash equilibrium that guarantees certain payoffs to all participants. Another attractive solution concept is a Nash equilibrium that maximizes the social welfare. We show that, while exactly computing the latter is infeasible (we prove that solving this problem may involve algebraic numbers of an arbitrarily high degree), there exists an FPTAS for finding such an equilibrium as long as the best ...
2007-01-01
Combining anatomy and function: the path to true image fusion
Energy Technology Data Exchange (ETDEWEB)
Modern imaging technologies visualize different aspects of disease in a non-invasive way. Considerable progress has been made in the fusion of images from different imaging modalities using software approaches. One goal of fusion software is to align anatomical and functional images and allow improved spatial localization of abnormalities. The resulting correlation of the anatomical and functional images may clarify the nature of the abnormality and help diagnose or stage the underlying disease. Whereas successful image fusion software has been developed for the brain, only limited success has been achieved for image alignment in other parts of the body. The development and current status of alternative approaches are presented. Dual-modality imaging is described with devices where two modalities are combined and mounted in a single gantry. The use of existing scanner technology ensures that no compromises are made in the clinical efficacy of either the anatomical or functional imaging ...
2001-10-01
Energy Technology Data Exchange (ETDEWEB)
The Bureau of Mines recently completed peliminary studies to demonstrate the feasibility of using Ground-Penetrating Radar (GPR) for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using transillumination. Data were gathered on multiple travel paths, and a back-projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomogrpahic technique, and the results were compared with those of the actual data. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take.
1987-01-01
Energy Technology Data Exchange (ETDEWEB)
Radiotherapy with high-energy carbon ion beams can be more advantageous compared to photons because of better physical dose distribution and higher biological efficiency in tumour cell sterilization. Despite enhanced normal tissue sparing, damage incurred by normal cells at the beam entrance is unavoidable and may affect the progeny of surviving cells in the form of inheritable cytogenetic alterations. Furthermore, the quality of the beam along the Bragg curve is modified by nuclear fragmentation of projectile and target nuclei in the body. We present an experimental approach based on the use of a polymethylmethacrylate (PMMA) phantom that allows the simultaneous exposure to a particle beam of several biological samples positioned at various depths along the beam path. The device was used to measure the biological effectiveness of a 60 MeV/amu carbon-ion beam at inducing chromosomal aberrations in G{sub 0}-human peripheral blood lymphocytes. Chromosome spreads were ...
2007-06-15
China's conception of energy security : sources and international impacts
International Nuclear Information System (INIS)
The unique challenges and opportunities associated with China's rapid economic growth were discussed with reference to the potential risk of political disruption or destabilizing international markets. The author notes that two common mistakes are typically made when assessing the evolution of China's energy policy. The first is that China's future path is assimilated with that of developed countries, thereby dismissing evidence that might point toward a different relationship with energy. Second, analysts tend to focus on the external expression of China's energy needs, its oil imports, while overlooking other energy-related issues such as insufficient electricity supplies or environmental degradation. The author argues that Chinese leadership is redefining its understanding of what constitutes energy security for the country. This report assesses the international impacts of such a redefinition along with the international aspects of a business-as-usual scenario ...
Challenges in fabrication of 180deg magnet chamber
International Nuclear Information System (INIS)
180 deg magnet chamber is used in Folded Tandem Ion Accelerator for passage and 180 deg bending of ion beam. The chamber is placed between 180 deg terminal magnet (Electro-magnet), which is used for bending, and analysing the beams. Magnet with a particular magnetic field strength bends ions of only specified mass energy product through a precise path. There is also a space limitation in the direction of magnetic field. Both of them require the magnet chamber to be of a close tolerance. Accuracy of center distance between inlet and outlet port of the magnet chamber has to be at par with the concentricity of high energy and low energy beam line. To achieve this we started the fabrication of magnet chamber by following two methods: a) Circular rolling and bending of rectangular tube for 180 deg sector of magnet chamber b) Machining 180 deg sector in two half and welding. By first method we could not achieve the desired result although the method is very promising. ...
2006-11-01
Cars and fuels for tomorrow: A comparative assessment
International Nuclear Information System (INIS)
Light duty vehicles, i.e. passenger cars and light trucks, account for approximately half of global transportation energy demand and, thus, a major share of carbon dioxide and other emissions from the transport sector. Energy consumption in the transport sector is expected to grow in the future, especially in developing countries. Cars with alternative powertrains to internal combustion engines (notably battery, hybrid and fuel-cell powertrains), in combination with potentially low carbon electricity or alternative fuels (notably hydrogen and methanol), can reduce energy demand by at least 50%, and carbon dioxide and regulated emissions much further. This article presents a comparative technical and economic assessment of promising future fuel/vehicle combinations. There are several promising technologies but no obvious winners. However, the electric drivetrain is a common denominator in the alternative powertrains and continued cost reductions are important for widespread deployment ...
2001-05-01
Can magnetospheric electron temperature be inferred from whistler dispersion measurements
International Nuclear Information System (INIS)
An approximate expression for whistler-mode group velocity is obtained, taking into account the effects of electron temperature and anisotropy, density and ion effects, effects of oblique propagation and a non-dipolarity of the dayside magnetospheric magnetic field. This expression is applied to the propagation of whistlers between one hemisphere and the other. It is pointed out that at frequencies close to the upper cut-off of whistler spectra, perturbations to whistler group delay times due to temperature effects can be of the same order of magnitude as, or even higher than, the corresponding perturbations due to finite electron density and ion effects. A method of magnetospheric electron temperature diagnostics is proposed and applied to two whistlers recorded at Halley (L = 4.3). It is pointed out that the values of temperature obtained from the analysis of whistler spectra depend on the choice of model of electron density and temperature distribution in the magnetosphere and on ...
Calculation of groundwater travel time
Energy Technology Data Exchange (ETDEWEB)
Pre-waste-emplacement groundwater travel time is one indicator of the isolation capability of the geologic system surrounding a repository. Two distinct modeling approaches exist for prediction of groundwater flow paths and travel times from the repository location to the designated accessible environment boundary. These two approaches are: (1) the deterministic approach which calculates a single value prediction of groundwater travel time based on average values for input parameters and (2) the stochastic approach which yields a distribution of possible groundwater travel times as a function of the nature and magnitude of uncertainties in the model inputs. The purposes of this report are to (1) document the theoretical (i.e., mathematical) basis used to calculate groundwater pathlines and travel times in a basalt system, (2) outline limitations and ranges of applicability of the deterministic modeling approach, and (3) explain the motivation for the use of the ...
1984-12-01
Biaxial Bianchi type IX quantum cosmology
Energy Technology Data Exchange (ETDEWEB)
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no rapidly oscillating semiclassical components in the wave function, and hence do not recover lorentzian space-time as a prediction of the no-boundary proposal. For the case with a cosmological constant the wave function does contain rapidly oscillating components and thus predicts approximately lorentzian space-times; ...
1991-03-11
Biaxial Bianchi type IX quantum cosmology
International Nuclear Information System (INIS)
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no rapidly oscillating semiclassical components in the wave function, and hence do not recover lorentzian space-time as a prediction of the no-boundary proposal. For the case with a cosmological constant the wave function does contain rapidly oscillating components and thus predicts approximately lorentzian space-times; ...
BWR containment vessel drywell head bolt de-tensioning during noble metal chemical application
Energy Technology Data Exchange (ETDEWEB)
Implementation of Noble Metal Chemical Application (NMCA) in a Boiling Water Reactor (BWR) requires injection of a noble metal compound while the reactor is idle at hot shutdown conditions. In order to minimize outage time, utilities are very pro-actively finding ways to reduce the number of critical path tasks. One of these tasks is to remove some containment vessel drywell head bolts during the NMCA idle time. This, thereby, saves the utilities outage time, or they can perform other tasks as desired. Using design basis conditions and state-of-the-art analytical techniques, detailed finite element stress analyses of the closure region are performed. Two acceptance criteria are evaluated. The first is that contained within Section III of the ASME Code for allowable stresses. The second relates to leak tightness, i.e., with bolt removal the joint must still remain leak tight. This paper describes the activities performed to justify bolt removal during the noble ...
2001-07-01
Atomic beam spectrometer using a LiF analyzer crystal
International Nuclear Information System (INIS)
An energy analyzer has been constructed and operated in UHV for the purpose of analyzing the energy of neutral atoms scattered from solid surfaces. The analyzer consists of a LiF single crystal located at an angle close to the normal to the sample crystal so that the diffraction pattern obtained by scanning the LiF crystal yields the energy of the scattered atoms. Two designs which have been used are described. The temperature of both sample and analyzer crystal is near 20 K and once cleaned they can be maintained in the state of initial preparation for many weeks. The sample was a (001) Cu surface in this case. Such an energy analyzer can only be used, in most cases, for He atom scattering although Ne atoms could be used if the scattered intensities were adequate. The detector developed in this study is able to detect about 2 x 10"5 atoms/s. The resolution of the spectrometer depends on the incident energy of the atom and is about 1 meV at an incident energy of 23 meV. This resolution ...
1978-01-01
Application of hydraulic network analysis to motor operated butterfly valves in nuclear power plants
International Nuclear Information System (INIS)
This paper presents the application of hydraulic network analysis to evaluate the performance of butterfly valves in nuclear power plant applications. Required actuation torque for butterfly valves in high-flow applications is often dictated by peak dynamic torque. The peak dynamic torque, which occurs at some intermediate disc position, requires accurate evaluation of valve flow rate and pressure drop throughout the valve stroke. Valve flow rate and pressure drop are significantly affected by the valve flow characteristics and the hydraulic system characteristics, such as pumping capability, piping resistances, single and parallel flow paths, system hydrostatic pressure, and the location of the motor-operated valve (MOV) within the system. A hydraulic network analysis methodology that addresses the effect of these parameters on the MOV performance is presented. The methodology is based on well-established engineering principles. The application of this methodology ...
1992-07-01
An Optimized Lifetime Enhancement Scheme for Data Gathering in Wireless Sensor Networks
Design of energy efficient schemes for data gathering is an important concern for lifetime enhancement of wireless sensor networks. Variation in the distances of nodes from the Base Station and differences in inter-nodal distances are primary factors causing unequal energy dissipation among the nodes. Thus energy difference between the various nodes increases with time resulting in degraded network performance. The LEACH and PEGASIS schemes which provided elegant solutions to the problem suffer basic drawbacks due to randomization of cluster heads and greedy chain formation respectively. In this paper, we propose an Optimized Lifetime Enhancement (OLE) Scheme which shows enhanced performance over these schemes. OLE increases the network performance by ensuring a sub-optimal energy dissipation of the individual nodes despite their random deployment. It employs modern heuristics like particle swarm optimization instead of the greedy algorithm as in PEGASIS to construct energy efficient ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
Ex situ and in situ fuel cell degradation of a sPAEK membrane were investigated. Post-mortem analyses of the aged membrane and of the degradation products eluted in water were carried out by NMR, IR, SEC and EDX. Ex situ agings were performed in a low concentration H{sub 2}O{sub 2} solution (0.07%) without any metallic catalyst. We exemplify that ex situ accelerated aging tests in such hydrogen peroxide solution are relevant to the chemical degradation in fuel cell. We have shown that a 500 h fuel cell test at moderate temperature (60 C) induces significant modifications on the macromolecules such as a 40% molecular weight reduction. Degradation appears heterogeneous and limited to the cathode side. The model compound approach developed in the previous article (Perrot et al.) has allowed the identification of the aging path in fuel cell. Phenolic and carboxylic acid chain ends have been identified as the main products resulting from polymer chain scissions. The ex ...
2010-01-15
Acid soil infertility effects on peanut yields and yield components
Energy Technology Data Exchange (ETDEWEB)
The interpretation of soil amelioration experiments with peanuts is made difficult by the unpredictibility of the crop and by the many factors altered when ameliorating acid soils. The present study was conducted to investigate the effects of lime and gypsum applications on peanut kernel yield via the three first order yield components, pods per ha, kernels per pod, and kernel mass. On an acid medium sandy loam soil (typic Plinthustult), liming resulted in a highly significant kernel yield increase of 117% whereas gypsum applications were of no significant benefit. As indicated by path coefficient analysis, an increase in the number of pods per ha was markedly more important in increasing yield than an increase in either the number of kernels per pod or kernel mass. Furthermore, exch. Al was found to be particularly detrimental to pod number. It was postulated that poor peanut yields resulting from acid soil infertility were mainly due to the depressive effect of ...
1983-01-01
International Nuclear Information System (INIS)
A personal computer based single specimen unloading technique has been demonstrated using a nuclear grade pressure vessel material, A533B Class I steel, and an #alpha#-#beta# titanium alloy, CORONA-5. Experimental parameters investigated in the case of steel include the effect of test temperature, loading rate and neutron irradiation. Results revealed the effect of dynamic strain aging (DSA) as a drop in the critical crack initiation fracture toughness (Jsub(q)); the minimum in Jsub(q) shifts to higher temperatures at higher test speeds as predicted from DSA models. In CORONA-5, the effects of microstructure and heat treatment for two different sizes of equiaxed #alpha# morphology in a #beta#-matrix heat treated to different yield strengths were investigated. It is found that the observed higher values of Jsub(q) and tearing modulus result from a greater tortuosity of the crack path and ease of crack blunting. The largest increase in Jsub(q) occurred in fine ...
In Graph Theory a number of results were devoted to studying the computational complexity of the number modulo 2 of a graph's edge set decompositions of various kinds, first of all including its Hamiltonian decompositions, as well as the number modulo 2 of, say, Hamiltonian cycles/paths etc. While the problems of finding a Hamiltonian decomposition and Hamiltonian cycle are NP-complete, counting these objects modulo 2 in polynomial time is yet possible for certain types of regular undirected graphs. Some of the most known examples are the theorems about the existence of an even number of Hamiltonian decompositions in a 4-regular graph and an even number of such decompositions where two given edges e and g belong to different cycles (Thomason, 1978), as well as an even number of Hamiltonian cycles passing through any given edge in a regular odd-degreed graph (Smith's theorem). The present article introduces a new algebraic technique which generalizes the notion of ...
2010-01-01
A dynamic approach to selectivity in heterogeneous partial oxidation
Energy Technology Data Exchange (ETDEWEB)
Despite the rapid development of literature pertaining to fundamental (1-4) studies of oxidation catalysis, a general theory of heterogeneous selective oxidation catalysis explaining the selectivity behavior of different metal oxide systems has not yet been developed. Redox mechanisms have been widely invoked in the kinetic and mechanistic descriptions of selective oxidation reactions, suggesting a dynamic behavior of hydrocarbon and oxygen interactions with the catalyst surface. Nevertheless, most of the recent theoretical approaches of this subject matter (5-7) are essentially static in nature. Correlations are made with surface structure on the basis of crystallographic considerations with selectivity being related to the nature, number, bond-strength and nearness of oxygen atoms in the neighborhood of adsorption centers. The effect of the reaction medium on the configuration of the catalyst surface, and thus its influence on the reaction path, are generally not ...
1987-08-01
A Novel VLSI Architecture of Fixed-complexity Sphere Decoder
Fixed-complexity Sphere Decoder (FSD) is a recently proposed technique for Multiple-Input Multiple-Output (MIMO) detection. It has several outstanding features such as constant throughput and large potential parallelism, which makes it suitable for efficient VLSI implementation. However, to our best knowledge, no VLSI implementation of FSD has been reported in the literature, although some FPGA prototypes of FSD with pipeline architecture have been developed. These solutions achieve very high throughput but at very high cost of hardware resources, making them impractical in real applications. In this paper, we present a novel four-nodes-per-cycle parallel architecture of FSD, with a breadth-first processing that allows for short critical path. The implementation achieves a throughput of 213.3 Mbps at 400 MHz clock frequency, at a cost of 0.18 mm2 Silicon area on 0.13{\\mu}m CMOS technology. The proposed solution is much more economical compared with the existing ...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
For heavy-ion beam driven inertial fusion ''liquid-protected'' reactor designs such as HYLIFE-II, a mixture of molten salts made of F{sup 10}, Li{sup -6}, Li{sup 7} and Be{sup 9} (called flibe) allows small chambers and final-focus magnets closer to the target with superconducting coils suffering higher radiation damage, though they can stand only a certain amount of energy deposited before quenching. This work has been primarily focusing on verifying that total energy deposited by fusion neutrons and induced gamma rays remain under such limit values and the final purpose is the optimization of the shielding of the magnetic lens system from the points of view of the geometrical configuration and of the physical nature of the materials adopted. The system is analyzed in terms of six geometrical models going from simplified up to much more realistic representations of a system of 192 beam lines, each focused by six magnets. A 3-D transport calculation ...
2002-07-01
WASTE TREATMENT AND DISPOSAL PROGRESS REPORT FOR JUNE AND JULY 1962
9 9 simulated Purex waste oxides was investigated as a function of Na/sub 2/O, CaO and P/sub 2/O/sub 5/ content. All compositions lost some sulfate at 50 to 100 deg C above the softening point. In generai the volatility decreased with increase of either Na/ sub 2/O or CaO relative to P/sub 2/O/sub 5/, but no simple correlation Was indicated. Softening temperatures were lowered by inc ease in Na/sub 2/O vs CaO. Ceramic solids were obtained but no true glasses. Attempts to produce glasses by addition of varying combinations of Al/sub 2/O/sub 3/, PbO, BaO, and B/sub 2/O/ sub 3/ to simulated Pure x waste plus phosphite were unsuccessful. The use of 0.005 M Na/sub 2/C/O/sub 3/ to precipitate calcium from wastes containing up to 3 ppm of phosphate was demonstrated in four pilot plant runs and produced a decrease in the hardness of the waste leaving the clarifier. An inadvertent Sr/ sup 90/ and Cs/sup 137/ breakthrough occurred during one run which was caused ...
1962-12-19
Energy Technology Data Exchange (ETDEWEB)
The most relevant aspects of research and service experience with environmentally-assisted cracking (EAC) of carbon (C) and low-alloy steels (LAS) in high-temperature (HT) water are reviewed, with special emphasis on the primary pressure boundary components of boiling water reactors (BWRs). The main factors controlling the susceptibility to EAC under light water reactor (LWR) conditions are discussed with respect to crack initiation and crack growth. The adequacy and conservatism of the current BWRVIP-60 stress corrosion cracking (SCC) disposition lines (DLs), ASME III fatigue design curves, and ASME XI reference fatigue crack growth curves, as well as of the GE EAC crack growth model are evaluated in the context of recent research results. The operating experience is summarized and compared to the experimental/mechanistic background knowledge. Finally, open questions and possible topics for further research are identified. Laboratory investigations revealed ...
2005-11-15
Energy Technology Data Exchange (ETDEWEB)
{gamma}-ray excitation functions have been measured for the interaction of fast neutrons with {sup 48}Ti (neutron energy from 1 MeV to 250 MeV). The Los Alamos National Laboratory spallation neutron source, at the LANSCE/WNR facility, provided a ''white'' neutron beam which is produced by bombarding a natural W target with a pulsed proton beam. The prompt-reaction {gamma} rays were measured with the large-scale Compton-suppressed Ge spectrometer, GEANIE. Neutron energies were determined by the time-of-flight technique. Excitation functions were converted to partial {gamma}-ray cross sections, taking into account the dead-time correction, the target thickness, the detector efficiency, and neutron flux (monitored with an in-line fission chamber). The data analysis is presented here for neutron energies between 1 to 20 MeV. Partial {gamma}-ray cross sections for transitions in {sup 47,48}Ti, {sup 48}Sc, and {sup 45}Ca have been determined. These results ...
2005-01-06
DEFF Research Database (Denmark)
The evolution of "humanized" (i.e., free of animal sourced reagents) and ultimately chemically defined culture systems for human embryo stem cell (hESC) isolation and culture is of importance to improving their efficacy and safety in research and therapeutic applications. This can be achieved by integration of a multitude of individual approaches to replace or eliminate specific animal sourced reagents into a single comprehensive protocol. In the present study our objective was to integrate strategies obviating reliance on some of the most poorly defined and path-critical factors associated with hESC derivation, namely the use of animal immune compliment to isolate embryo inner cell mass, and animal sourced serum products and feeder cells to sustain hESC growth and attachment. As a result we report the derivation of six new hESC lines isolated by outgrowth from whole blastocysts on an extracellular matrix substrate of purified human laminin (Ln) with transitional ...
2006-01-01
Trends in robotics: A summary of the Department of Energy`s critical technology roadmap
Energy Technology Data Exchange (ETDEWEB)
Technology roadmaps serve as pathways to the future. They call attention to future needs for research and development; provide a structure for organizing technology forecasts and programs; and help communicate technological needs and expectations among end users and the research and development (R and D) community. Critical Technology roadmaps, of which the Robotics and Intelligent Machines (RIM) Roadmap is one example, focus on enabling or cross-cutting technologies that address the needs of multiple US Department of Energy (DOE) offices. Critical Technology roadmaps must be responsive to mission needs of the offices; must clearly indicate how the science and technology can improve DOE capabilities; and must describe an aggressive vision for the future of the technology itself. The RIM Roadmap defines a DOE research and development path for the period beginning today, and continuing through the year 2020. Its purpose is to identify, select and develop objectives ...
1998-08-10
The thorny path linking cellular senescence to organismalaging
Energy Technology Data Exchange (ETDEWEB)
Half a century is fast approaching since Hayflick and colleagues formally described the limited ability of normal human cells to proliferate in culture (Hayflick and Moorhead, 1961). This finding--that normal somatic cells, in contrast to cancer cells, cannot divide indefinitely--challenged the prevailing idea that cells from mortal multicellular organisms were intrinsically ''immortal'' (Carrell, 1912). It also spawned two hypotheses, essential elements of which persist today. The first held that the restricted proliferation of normal cells, now termed cellular senescence, suppresses cancer (Hayflick, 1965; Sager, 1991; Campisi, 2001). The second hypothesis, as explained in the article by Lorenzini et al., suggested that the limited proliferation of cells in culture recapitulated aspects of organismal aging (Hayflick, 1965; Martin, 1993). How well have these hypotheses weathered the ensuing decades? Before answering this question, we first consider ...
2005-08-09
The life span of the biosphere revisited
Energy Technology Data Exchange (ETDEWEB)
A decade ago, Lovelock and Whitfield raised the question of how much longer the biosphere can survive on Earth. They pointed out that, despite the current fossil-fuel induced increase in the atmospheric CO[sub 2] concentration, the long-term trend should be in the opposite direction: as increased solar luminosity warms the Earth, silicate rocks should weather more readily, causing atmospheric CO[sub 2] to decrease. In their model, atmospheric CO[sub 2] falls below the critical level for C3 photosynthesis, 150 parts per million (p.p.m.), in only 100 Myr, and this is assumed to mark the demise of the biosphere as a whole. Here, this problem is re-examined using a more elaborate model that includes a more accurate treatment of the greenhouse effect of CO[sub 2] a biologically mediated weathering parameterization, and the realization that C4 photosynthesis can persist to much lower concentrations of atmospheric CO[sub 2] ([lt]10 p.p.m.). It was found that a C4-plant-based biosphere could ...
1992-12-24
Energy Technology Data Exchange (ETDEWEB)
The primary coolant oxidises the surfaces of construction materials in nuclear power plants. The properties of the oxide films influence significantly the extent of incorporation of actuated corrosion products into the primary circuit surfaces, which may cause additional occupational doses for the maintenance personnel. The physical and chemical properties of the oxide films play also an important role in different forms of corrosion observed in power plants. This report gives a short overview of the factors influencing activity build-up and corrosion phenomena in nuclear power plants. Furthermore, the most recent modifications in the water chemistry to decrease these risks are discussed. A special focus is put on zinc water chemistry, and a preliminary discussion on the mechanism via which zinc influences activity build-up is presented. Even though the exact mechanisms by which zinc acts are not yet known, it is assumed that Zn may block the diffusion paths within ...
1999-03-01
International Nuclear Information System (INIS)
According to the data of drill cores, outcrops and well logging, two orders base-level cycles are recognized from Zhiluo Formation in Dongsheng area, which consist of 8-14 short-term base-level cycles and 3 mid-term base-level cycles, and their structural types and stacking patterns are discussed by using principles and methods of high-resolution sequence stratigraphic theory. Based on the correlation of mid-term base-level cycles, the control of the A/S (Accommodation/Sediment supply) ratio in mid-term base-level cycles on the scale of sand bodies and physical properties of reservoir is analysed. Studies show that the sand bodies of braided stream in MSC1 of Zhiluo Formation are favourable to uranium mineralization, however, the sand bodies of meandering river in MSC2 and MSC3 are not favourable to uranium mineralization. The change of the A/S results in the difference in characters of sand body, such as physical properties, continuity and so on, which control the fluid flowing ...
2007-01-01
THE EVOLUTION OF LYMAN LIMIT ABSORPTION SYSTEMS TO REDSHIFT SIX
International Nuclear Information System (INIS)
We have measured the redshift evolution of the density of Lyman limit systems (LLSs) in the intergalactic medium over the redshift range 0 < z < 6. We have used two new quasar samples to (1) improve coverage at z #approx# 1, with GALEX grism spectrograph observations of 50 quasars with 0.8 < z_e_m < 1.3, and (2) extend coverage to z #approx# 6, with Keck ESI spectra of 25 quasars with 4.17 < z_e_m < 5.99. Using these samples together with published data, we find that the number density of LLS per unit redshift, n(z), can be well fit by a simple evolution of the form n(z) = n_3_._5[(1 + z)/4.5]"#gamma# with n_3_._5 = 2.80 #+-# 0.33 and #gamma# = 1.94"+"0"."3"6_-_0_._3_2 for the entire range 0 < z < 6. We have also reanalyzed the evolution of damped Ly#alpha# systems (DLAs) in the redshift range 4 < z < 5 using our high-redshift quasar sample. We find a total of 17 DLAs and sub-DLAs, which we have analyzed in combination with published data. The DLAs with ...
2010-10-01
Energy Technology Data Exchange (ETDEWEB)
This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), loading collapse (LC) and saturation ...
2007-12-15
Study on thermal-hydraulics during a PWR reflood phase
International Nuclear Information System (INIS)
In-core thermal-hydraulics during a PWR reflood phase following a large-break LOCA are quite unique in comparison with two-phase flow which has been studied widely in previous researches, because the geometry of the flow path is complicated (bundle geometry) and water is at extremely low superficial velocity and almost under stagnant condition. Hence, some phenomena realized during a PWR reflood phase are not understood enough and appropriate analytical models have not been developed, although they are important in a viewpoint of reactor safety evaluation. Therefore, author investigated some phenomena specified as important issues for quantitative prediction, i.e. (1) void fraction in a bundle during a PWR reflood phase, (2) effect of radial core power profile on reflood behavior, (3) effect of combined emergency core coolant injection on reflood behavior, and (4) the core separation into two thermal-hydraulically different regions and the in-core flow circulation ...
1983-12-13
Simulation of dopant diffusion and activation during flash lamp annealing
International Nuclear Information System (INIS)
A set of advanced models implemented into the simulator Sentaurus Process was applied to simulate ultra shallow junction formation by flash lamp annealing (FLA). The full path transient enhanced diffusion model includes equations for small interstitial clusters (I_2, I_3, I_4), #left brace#3 1 1#right brace# defects and dislocation loops. A dopant-point defect clustering model is used for dopant activation simulation. Several cluster types are considered: B_2, B_2I, B_2I_2, B_3I, B_3I_2, B_3I_3 for boron and As_2, As_2V, As_3, As_3V, As_4, As_4V for arsenic. Different point defect and dopant-point defect pair charge states are taken into account to obtain accurate results in the high doping level region. The flux expressions in the three-phase segregation model include a dependence on the doping level and point defect supersaturation. The FLA process was performed at various peak temperatures in a Mattson Millios"T"M fRTP"T"M system. The measured wafer temperature ...
2008-12-05
Energy Technology Data Exchange (ETDEWEB)
After the transcription of the electricity directive in national legislations, the European electricity market appears to be a vast set of juxtaposed markets which are weakly connected at the level of their wholesale contracts compartment. Referring to the technological peculiarities of electricity as a commodity, the paper identifies the direct conditions of regional integration of the electricity markets, those which would favour cross-border trade and allow to be near the normal functioning of a regional commodity market. The infrastructure network dependence and the need of a stringent technical coordination necessitate to unify the operation of the different systems and the rules of access, or at the least to come near this unification by strong coordination. A second major condition, which is not fully debated, is the increasing connexion of short-term markets, via daily physical trade and emergence of a European financial market, which could trade various standardised contracts ...
2000-11-01
Reflection tomography using finite element method ray tracing
Energy Technology Data Exchange (ETDEWEB)
The seismic reflection exploration technique which is one of the geophysical methods for oil exploration became effectively to image the subsurface structure with rapid development of computer. As a tool to perform seismic inversion, seismic forward modeling program using ray tracing should be developed. In this study, we have developed the algorithm that is to calculate the travel time of the complex geological structure using ray tracing by subdividing the geologic model into triangular element (finite element) having the constant velocity. We can analytically calculate Jacobian with some information by this current ray tracing. With this Jacobian, we will develop new algorithm which is to obtain geological properties and to image the subsurface. After subdividing subsurface into triangular element we shoot off the ray into subsurface by the Snell`s law. And then after taking the ray path which is similar to proper assumption we can calculate travel time. With ...
1996-12-01
International Nuclear Information System (INIS)
Radio frequency (RF) sheaths are suspected of limiting the performance of present-day ion cyclotron range of frequencies (ICRFs) antennas over long pulses and should be minimized in future fusion devices. Within the simplest models, RF-sheath effects are quantified by the integral VRF = ? E|| ? dl where the parallel RF field E|| is linked with the slow wave. On 'long open field lines' with large toroidal extension on both sides of the antenna it was shown that VRF is excited by parallel RF currents j|| flowing on the antenna structure. In this paper, the validity of this simple sheath theory is tested experimentally on the Tore Supra (TS) ITER-like antenna prototype (ILP), together with antenna simulation and post-processing codes developed to compute VRF. The predicted poloidal localization of high-|VRF| zones is confronted to that inferred from experimental data analysis. Surface temperature distribution on ILP front face, as well as ILP-induced modifications of RF coupling and hot ...
2010-02-01
Energy Technology Data Exchange (ETDEWEB)
The regenerator of Stirling cycle machines has an relatively unknown potential for thermal shorting, because the thermal flow path within the solid of a randomly stacked wire mesh, which is defined by its 'connectivity', is unknown. Earlier publications have shown two principles of experimental techniques to quantify connectivity. One quantifies connectivity as a function of axial pressure using the electric current analogy, the other measures connectivity via the temperature gradients along a regenerator and a series-connected reference body of known conductivity. Both papers offer preliminary results of reduced usefulness related to the testing method or setup. This contribution describes a new setup and its technique, which results from the practical knowledge and experience of the first two attempts, and aims for an improved determination of connectivity of the original representative Stirling regenerators with and without housing. Please ...
2000-07-01
Energy Technology Data Exchange (ETDEWEB)
Airbag pressure vessels for the north-American market mainly are made by forging and by the use of steel alloys. In Europe aluminum alloys are common and the manufacturing process is extrusion of circular blanks - made from cold rolled plates - in a form applying a 100 t press at room temperature. Then by heat treatment the strength/hardness of the material is properly adjusted and after that the pressure vessel parts have to be continuously inspected with an inspection and handling cycle time of 3 s. Inspection of the axis-symmetric parts is asked for surface breaking extrusion defects as well as for surface parallel delaminations in the bulk volume. Furthermore, the material strength is a quality characteristic that has to be nondestructively registered and documented. The inspection is performed by eddy current probes and an EMAT, of which the eddy current impedance measurements are used for surface breaking extrusion defect detection and sizing (single frequency technique with ...
1999-07-01
Power Tower Technology Roadmap and cost reduction plan.
Energy Technology Data Exchange (ETDEWEB)
Concentrating solar power (CSP) technologies continue to mature and are being deployed worldwide. Power towers will likely play an essential role in the future development of CSP due to their potential to provide dispatchable solar electricity at a low cost. This Power Tower Technology Roadmap has been developed by the U.S. Department of Energy (DOE) to describe the current technology, the improvement opportunities that exist for the technology, and the specific activities needed to reach the DOE programmatic target of providing competitively-priced electricity in the intermediate and baseload power markets by 2020. As a first step in developing this roadmap, a Power Tower Roadmap Workshop that included the tower industry, national laboratories, and DOE was held in March 2010. A number of technology improvement opportunities (TIOs) were identified at this workshop and separated into four categories associated with power tower subsystems: solar collector field, solar receiver, thermal ...
2011-04-01
Planning and management of change
Energy Technology Data Exchange (ETDEWEB)
The 1990s promise to be a decade of change. In business, the focus will be on restructuring for purposes of improved productivity and efficiency. The Department of Energy (DOE) has recognized that change is on the horizon. The Yucca Mountain Project, carried out under the Office of Civilian Radioactive Waste Management (OCRWM) within the DOE is under new leadership. This new leadership is restructuring its operations to provide better focus, greater efficiency, meaningful products demonstrating progress and a more open operational environment. Criticisms of past operations have been reviewed and evaluated such that the new management organization derives benefit from the past. In recognition that management concerns may be manifested in other areas, Yucca Mountain Project management believes that reorganization is necessary to maximize efficiency. In designing the new organization, a high priority has been placed upon making changes which enable the federal leadership to exercise ...
1994-12-31
PNC`s proposal on the Advanced Fuel Recycle concept
Energy Technology Data Exchange (ETDEWEB)
MOX fuel for FBR is allowed to contain impurities within several thousand ppm, which means less than 1000 of decontamination factor (DF) in reprocessing is enough for Pu and U recycle use. The Advanced Fuel Recycle proposed by PNC is on this basis. The concept consists of innovations on both MOX fuel fabrication and aqueous reprocessing technologies based on the Purex process and it is believed that successful optimization of fuel cycle interface condition is the key issue to realize the concept. The lower DF such as 1000 can be easily obtained by the simplified Purex flowsheet which has no purification steps. However, new subject arises in MOX fuel fabrication, that is, fabrication is conducted in the shielding cell using equipment which is maintained remotely. A simplified fabrication technology becomes essential to establish the remote maintenance system and is one of the critical path for achieving the Advanced Fuel Recycle. The PNC`s proposal on the advanced ...
1998-03-01
Energy Technology Data Exchange (ETDEWEB)
In coke-oven operations flue-gas valves are used to switch the regenerator function from rich gas firing to lean gas firing. Compared with the simple geometry of the other parts of the flow path, which comprise flues and regenerators, the narrow and winding passages of the flue-gas valves give rise to relatively high losses in pressure. Without the construction of high (and therefore expensive) chimneys, this means that operating problems may well arise due the inadequate suction capacity. The project focused on the theoretical and experimental analysis of a coke-oven flue-gas valve. The primary aim was to reduce the pressure drop through the valve without modifying its external geomerty. The internal flow characteristics created by different valve geometries under a variety of operating conditions were simulated using the commercial CFD code Fluent/UNS, which provided velocity and pressure distributions. A half-scale model valve was constructed in order to ...
1999-06-01
On the Gravito-Electromagnetic Analogy
International Nuclear Information System (INIS)
Earlier research by Zel'manov and by Hoenl and Dehnen has shown how the geodesic equation for a charged test particle can be written as a Lorentz force law in which the four-velocity u"i of an observer in the physical three-space #gamma#_#alpha#_#beta# = -g_#alpha#_#beta# + g_0_#alpha# g_0_#beta# / g_0_0 is regarded as a gravitational vector potential. Analysing this analogy further, we write the four ("i_0) components of the Einstein equations in a form resembling a non-linear Maxwell system, which, for a stationary field, is most clearly understood from the Kaluza-Klein perspective, the projection being from four dimensions to three, rather than from five dimensions to four. For the vacuum theory defined by vanishing energy-momentum tensor, T_i_j = 0, these equations exhibit the structure of a non-linear sigma model, found by Ernst, and investigated by Gibbons and Hawking and by Sanchez, the scalar potentials of which we here relate to the gravito-electromagnetic fields. The ...
2011-08-01
On foundation of the generalized Nambu mechanics
International Nuclear Information System (INIS)
We outline basic principles of a canonical formalism for the Nambu mechanics - a generalization of Hamiltonian mechanics proposed by Yoichiro Nambu in 1973. It is based on the notion of a Nambu bracket, which generalizes the Poisson bracket - a 'binary'' operation on classical observables on the phase space - to the 'multiple' operation of higher order n#>=#3. Nambu dynamics is described by the phase flow given by Nambu-Hamilton equations of motion - a system of ODE's which involves n-1 'Hamiltonians'. We introduce the fundamental identity for the Nambu bracket - a generalization of the Jacobi identity - as a consistency condition for the dynamics. We show that Nambu bracket structure defines a hierarchy of infinite families of 'subordinated' structures of lower order, including Poisson bracket structure, which satisfy certain matching conditions. The notion of Nambu bracket enables us to define Nambu-Poisson manifolds - phase spaces for the Nambu mechanics, which turn out to be ...
Oleuropein aglycon prevents cytotoxic amyloid aggregation of human amylin.
Pancreatic amyloid deposits of amylin are a hallmark of Type II diabetes and considerable evidence indicates that amylin oligomers are cytotoxic to beta-cells. Many efforts are presently spent to find out naturally occurring molecules, or to design synthetic ones, able to hinder amylin aggregation or to protect cells against aggregate cytotoxicity. In this context, a protective effect of some polyphenols against amyloid cytotoxicity was reported. Actually dietary polyphenols are endowed with multiple health benefits, and extra virgin olive oil is attracting increasing interest as a source of these substances. Here, we investigated the effects on amylin aggregation and cytotoxicity of the secoiridoid oleuropein aglycon, the main phenolic component of extra virgin olive oil. We found that oleuropein, when present during the aggregation of amylin, consistently prevented its cytotoxicity to RIN-5F pancreatic beta-cells, as determined by the 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl ...
2009-07-18
Numerical ray tracing of electrons in different 3D fringing fields of spherical deflectors
This paper presents the results of numerical investigations on electron trajectories in different 3D fringing fields of spherical defectors. We start with a chosen set of geometrical values for the electrodes such as radius of curvature, electrode gap, angle between entrance and exit face. We do a first numerical calculation of the spatial potential distribution using a 3D electron optics program based on the finite difference method (FDM). Ray tracing through this potential distribution is then performed using another program, which also gives the potential and the electric field strength along the curved beam path. In the next step we estimate the position and the geometry of the field clamp using Herzog's formulae assuming the entrance of a parallel plate condenser to be a good approximation for the entrance of the spherical deflector in first order. For the consecutive numerical recalculations of the real potential distribution of the spherical deflector with ...
1999-11-01
Neural node network and model, and method of teaching same
Energy Technology Data Exchange (ETDEWEB)
The present invention is a fully connected feed forward network that includes at least one hidden layer 16. The hidden layer 16 includes nodes 20 in which the output of the node is fed back to that node as an input with a unit delay produced by a delay device 24 occurring in the feedback path 22 (local feedback). Each node within each layer also receives a delayed output (crosstalk) produced by a delay unit 36 from all the other nodes within the same layer 16. The node performs a transfer function operation based on the inputs from the previous layer and the delayed outputs. The network can be implemented as analog or digital or within a general purpose processor. Two teaching methods can be used: (1) back propagation of weight calculation that includes the local feedback and the crosstalk or (2) more preferably a feed forward gradient decent which immediately follows the output computations and which also includes the local feedback and the crosstalk. Subsequent ...
1995-01-01
Multiscale modeling of transdermal drug delivery
This study addresses the modeling of transdermal diffusion of drugs, to better understand the permeation of molecules through the skin, and especially the stratum corneum, which forms the main permeation barrier of the skin. In transdermal delivery of systemic drugs, the drugs diffuse from a patch placed on the skin through the epidermis to the underlying blood vessels. The epidermis is the outermost layer of the skin and can be further divided into the stratum corneum (SC) and the viable epidermis layers. The SC consists of keratinous cells (corneocytes) embedded in the lipid multi-bilayers of the intercellular space. It is widely accepted that the barrier properties of the skin mostly arises from the ordered structure of the lipid bilayers. The diffusion path, at least for lipophilic molecules, seems to be mainly through the lipid bilayers. Despite the advantages of transdermal drug delivery compared to other drug delivery routes such as oral dosing and ...
2006-01-01
Long-term modulation of cosmic rays in interplanetary magnetic turbulence
Energy Technology Data Exchange (ETDEWEB)
Long-term modulation of galactic cosmic rays in interplanetary magnetic field (IMF) turbulence is a fundamental subject for understanding the connection between cosmic ray transport and solar activity. The discovery of a new cosmic ray modulation phenomenon is reported. Analysis of neutron monitor data has revealed that the difference in amplitude of the cosmic ray diurnal anisotropy for IMF sectors directed toward and away from the Sun displays a solar cycle variation. Neutron monitor data recorded at Climax, Deep River, Hyancayo, Kiel, Mt. Washington, and Swarthmore/Newark over the period 1957 to 1988 show that the amplitude difference varied between approximately 0.1 to -0.1 percent, with peaks in 1960, 1972, and 1982. A theoretical expression for this difference was derived from a three-dimensional model. Analysis also showed that the latitudinal density gradient of cosmic rays changed between 1.6 and -1.6 percent/AU with a solar cycle variation, which may produce the variation of ...
1989-01-01
Justification Of The Use Of Boreholes For Disposal Of Sealed Radiological Sources
Energy Technology Data Exchange (ETDEWEB)
Soon there will be only 14 states in two compacts that are able to dispose of Low Level Waste (LLW): the Northwest and Rocky Mountain compact with disposal options in Richland, Washington, and the Atlantic compact with disposal options in Barnwell, South Carolina. How do states not in one of the two compacts dispose of their LLW? The Off-Site Source Recovery Project can take possession and dispose of some of the unwanted transuranic sources at the Waste Isolation Pilot Plant (WIPP). However, there will be no path forward for states outside of the two compacts for disposal of their non-transuranic LLW. A solution that has been much discussed, debated and researched, but has not been put into wide scale practice, is the borehole disposal concept. It is the author's position that companies that drill and explore for oil have been disposing of sources in borehole-like structures for years. It should be noted that these companies are not purposely disposing of ...
2008-01-01
Energy Technology Data Exchange (ETDEWEB)
According to ICRP 60 and European-Directive 96/29, Naturally Occurring Radioactive Materials (NORM) and Technical Enriched Naturally Occurring Radioactive Materials (TENORM) have to take the radiation protection of the general population as well as of workers into account. The German radiation protection regulations stress that particularly. In connection with these regulations, various measurement programs have been and still are performed to investigate the relevant exposure paths. One of these programs is the determination of the intake of natural occurring radionuclides of the uranium decay series in individuals of the public, in exposed regions and houses and also at NORM workplaces by excretion analysis. Excretion analysis surveillance is one of the common tools for internal dosimetry. Sources of primordial radionuclides could be the ingestion of foodstuff and water and the incorporation of (mostly airborne) pollution on work places. The main focus in this ...
2006-07-01
Interinstitutional Variations in Planning for Stereotactic Body Radiation Therapy for Lung Cancer
International Nuclear Information System (INIS)
Purpose: The aim of this study was to assess interinstitutional variations in planning for stereotactic body radiation therapy (SBRT) for lung cancer before the start of the Japan Clinical Oncology Group (JCOG) 0403 trial. Methods and Materials: Eleven institutions created virtual plans for four cases of solitary lung cancer. The created plans should satisfy the target definitions and the dose constraints for the JCOG 0403 protocol. Results: FOCUS/XiO (CMS) was used in six institutions, Eclipse (Varian) in 3, Cadplan (Varian) in one, and Pinnacle3 (Philips/ADAC) in one. Dose calculation algorithms of Clarkson with effective path length correction and superposition were used in FOCUS/XiO; pencil beam convolution with Batho power law correction was used in Eclipse and Cadplan; and collapsed cone convolution superposition was used in Pinnacle3. For the target volumes, the overall coefficient of variation was 16.6%, and the interinstitutional variations were not ...
2007-06-01
Energy Technology Data Exchange (ETDEWEB)
A feasibility study test and 3 field trials were performed at Darlington NGS in 1996, 1999 and 2000 on ABB LP turbines. The scope of these trials was to commission in-situ automatic phased array systems capable to inspect blade roots and rotor steeples of L-0 and L-1 rows. GE disk-blade rim attachments were inspected at Bruce B nuclear station, in fall of 1999. The automated ultrasonic phased array technology is capable of high-speed rate and reliable detection and sizing. The capability demonstration was performed on mock-ups and reference blocks, using EDM notches. A custom built UT simulation software: Imagine 3D interfaces with SimScan to generates the spreadsheets/charts with target and probe coordinates and ultrasonic path and angles (refracted and skew) to hit the reference target. Examination of L-0 blade and rotor steeple grooves was performed with 2 phased array systems under networking. Data analysis was done in near-real time. Manual and automatic ...
2000-07-01
Improved oil recovery using bacteria isolated from North Sea petroleum reservoirs
Energy Technology Data Exchange (ETDEWEB)
During secondary oil recovery, water is injected into the formation to sweep out the residual oil. The injected water, however, follows the path of least resistance through the high-permeability zones, leaving oil in the low-permeability zones. Selective plugging of these their zones would divert the waterflood to the residual oil and thus increase the life of the well. Bacteria have been suggested as an alternative plugging agent to the current method of polymer injection. Starved bacteria can penetrate deeply into rock formations where they attach to the rock surfaces, and given the right nutrients can grow and produce exo-polymer, reducing the permeability of these zones. The application of microbial enhanced oil recovery has only been applied to shallow, cool, onshore fields to date. This study has focused on the ability of bacteria to enhance oil recovery offshore in the North Sea, where the environment can be considered extreme. A screen of produced water ...
1995-12-31
Energy Technology Data Exchange (ETDEWEB)
This project, conducted under The United States Department of Energy (DOE) Cooperative Agreement DE-FC36-94GO10002/A002, was part of a multiple-phase effort to develop technologies that improve the energy efficiency and economics of chemical process recovery in the pulp and paper industry. The approach taken was to consider two major alternatives in two phases. Phase I, conducted previously, considered means to improve pulp mill recovery boilers using high-solids advanced combustion of black liquor; while this project, Phase la, considered means to recover kraft pulping mill process chemicals by low-temperature black liquor gasification. The principal steps previously proposed in this program were: (1) Evaluate these two technologies, high-solids advanced combustion and gasification, and then select a path forward using the more promising of these two options for future work. (2) Design and construct a pilot-scale unit based on the selected technology, and using ...
1997-06-01
Genomic analysis of the symbiotic marine crenarchaeon, Cenarchaeumsymbiosum
Energy Technology Data Exchange (ETDEWEB)
Crenarchaea are ubiquitous and abundant microbial constituents of soils, sediments, lakes and ocean waters, yet relatively little is known about their fundamental evolutionary, ecological, and physiological properties. To better describe the ubiquitous nonthermophilic Crenarchaea, we analyzed the genome sequence of one representative, the uncultivated sponge symbiont, Cenarchaeum symbiosum. C. symbiosum genotypes coinhabiting the same host partitioned into two dominant populations, corresponding to previously described a- and b-type ribosomal RNA variants. Although synthetic, overlapping a- and b-type ribotypes harbored significant genetic variability. A single tiling path comprising the dominant a-type genotype was assembled, and used to explore the biological properties of C. symbiosum and its planktonic relatives. Out of a total of 2,066 predicted open reading frames, 36% were more highly conserved with other Archaea. The remainder partitioned between bacteria ...
2006-06-24
Flow regime transfer conditions for two-phase flow in a fracture
Energy Technology Data Exchange (ETDEWEB)
Between 25 and 30 percent of total known petroleum reserves are contained within oil-laden fractured reservoirs where the dominant flow path is through the fractures. Economic oil recoveries from fractured reservoirs depend on a better understanding of the flow in fractures and networks of fractures. However, the flow of heavy oil and water, and particularly the flow regime map for two-phase immiscible flow has received less attention in contrast with gas-liquid flow in fractures. This paper discussed the use of flow pattern observations in a Hele-Shaw cell to generate two-phase flow regime maps. The paper investigated the effect of fracture gap and fluid viscosities on flow regimes. A correlation based on different flow and fracture properties was developed to define flow transition conditions between flow regimes. The paper presented the experiments, with particular reference to the experimental apparatus and the liquid-liquid system used in the experiments. ...
2010-07-01
Effects of strong and electromagnetic correlations on neutrino interactions in dense matter
Energy Technology Data Exchange (ETDEWEB)
An extensive study of the effects of correlations on both charged and neutral current weak interaction rates in dense matter is performed. Both strong and electromagnetic correlations are considered. The propagation of particle-hole interactions in the medium plays an important role in determining the neutrino mean free paths. The effects due to Pauli blocking and density, spin, and isospin correlations in the medium significantly reduce the neutrino cross sections. As a result of the lack of experimental information at high density, these correlations are necessarily model dependent. For example, spin correlations in nonrelativistic models are found to lead to larger suppressions of neutrino cross sections compared to those of relativistic models. This is due to the tendency of the nonrelativistic models to develop spin instabilities. Notwithstanding the above caveats, and the differences between nonrelativistic and relativistic approaches such as the spin- and ...
1999-05-01
Effect of vitamin D on the intestinal absorption of 203Pb and 47Ca in chicks
Energy Technology Data Exchange (ETDEWEB)
The transfer of 203Pb and/or 47Ca across the intestinal epithelium of the chick was investigated, with emphasis given to the functional role of cholecalciferol (vitamin D-3). 203Pb, after introduction in the intestinal lumen, is rapidly accumulated by the intestinal tissue, and only a fraction of 203Pb is translocated parenterally (absorbed). Cholecalciferol did not significantly affect the accumulation of 203Pb by intestinal tissue but did accelerate 203Pb movement across the basal-lateral membrane. In contrast, cholecalciferol both decreased 47Ca tissue levels and increased 47Ca absorption. In rachitic chicks, the rate of absorption of 203Pb was greater in the distal than in the proximal segments of the intestine; after cholecalciferol repletion, the degree of absorption in al segments was similar, indicting the order of cholecalciferol effectiveness as duodenum greater than or equal to jejunum greater than ileum. An acute dose of 1,25(OH)2D3 to rachitic chicks also enhanced both ...
1982-03-01
Effect of vitamin D on the intestinal absorption of /sup 203/Pb and /sup 47/Ca in chicks
Energy Technology Data Exchange (ETDEWEB)
The transfer of /sup 203/Pb and/or /sup 47/Ca across the intestinal epithelium of the chick was investigated, with emphasis given to the functional role of cholecalciferol (vitamin D-3). /sup 203/Pb, after introduction in the intestinal lumen, is rapidly accumulated by the intestinal tissue, and only a fraction of /sup 203/ Pb is translocated parenterally (absorbed). Cholecalciferol did not significantly affect the accumulation of /sup 203/Pb by intestinal tissue but did accelerate /sup 203/Pb movement across the basal-lateral membrane. In contrast, cholecalciferol both decreased /sup 47/Ca tissue levels and increased /sup 47/Ca absorption. In rachitic chicks, the rate of absorption of /sup 203/Pb was greater in the distal than in the proximal segments of the intestine; after cholecalciferol repletion, the degree of absorption in all segments was similar, indicating the order of cholecalciferol effectiveness as duodenum greater than or equal to jejunum > ileum. An acute dose of ...
1982-03-01
Effect of earthquakes on ambient noise cross-correlation function
Surface wave tomography method based on analysis of ambient noise is widely used during the last decade. It is assumed that correlated component of noise is composed of surface waves generated by sources distributed over the Earth's surface more or less uniformly. In such a case the cross-correlation function (CCF) at two stations may be considered as the Green's function of surface wave. This function should be symmetric relatively to zero time. However analysis of CCF at the stations located at the East-European Platform shows that as a rule CCF is characterized with a strong asymmetry. Since "purered noise cannot be extracted from seismic records due to superposition of earthquake signals, the method for calculation of CCF includes amplitude normalization for suppression of earthquakes that reduces signals from earthquakes to a noise level. The parts of records containing waves from earthquakes are neglected because of their short duration. Present study shows that this contribution ...
2011-09-01
Direct coal-fired gas turbines for combined cycle plants
Energy Technology Data Exchange (ETDEWEB)
The combustion/emissions control island of the CFTCC plant produces cleaned coal combustion gases for expansion in the gas turbine. The gases are cleaned to protect the turbine from flow-path degeneration due to coal contaminants and to reduce environmental emissions to comparable or lower levels than alternate clean coal power plant tedmologies. An advantage of the CFTCC system over other clean coal technologies using gas turbines results from the CFTCC system having been designed as an adaptation to coal of a natural gas-fired combined cycle plant. Gas turbines are built for compactness and simplicity. The RQL combustor is designed using gas turbine combustion technology rather than process plant reactor technology used in other pressurized coal systems. The result is simpler and more compact combustion equipment than for alternate technologies. The natural effect is lower cost and improved reliability. In addition to new power generation plants, CFTCC technology ...
1993-11-01
Deformation change in light iridium nuclei from laser spectroscopy
International Nuclear Information System (INIS)
Laser spectroscopy measurements have been performed on neutron-deficient and stable Ir isotopes using the COMPLIS experimental setup installed at ISOLDE-CERN. The radioactive Ir atoms were obtained from successive decays of a mass-separated Hg beam deposited onto a carbon substrate after deceleration to 1kV and subsequently laser desorbed. A three-color, two-step resonant scheme was used to selectively ionize the desorbed Ir atoms. The hyperfine structure (HFS) and isotope shift (IS) of the first transition of the ionization path 5d"76s"2"4F_9_/_2#->#5d"76s6p"6F_1_1_/_2 at 351.5nm were measured for "1"8"2"-"1"8"9Ir, "1"8"6Ir"m and the stable "1"9"1","1"9"3Ir. The nuclear magnetic moments #mu#_I and the spectroscopic quadrupole moments Q_s were obtained from the HFS spectra and the change of the mean square charge radii from the IS measurements. The sign of #mu#_I was experimentally determined for the first time for the masses 182#=#+0.2 for the lighter group ...
2006-12-01
Deforestation of Rondonia, Brazil, from 1975 to 2001
Throughout much of the 1980s, deforestation in Brazil eliminated more than 15,000 square kilometers (9000 square miles) per year. That pace has only increased through the 90s and into the 21st century. Brazil is also home to more than a quarter of Earths tropical forests. Considering that the band of lush green that circles the globe through many equatorial nations is fundamental to the overall health of the whole planets environment, careful monitoring of forest health in the tropics is essential. Tropical forests act as major carbon sinks, places where ambient carbon dioxide in the atmosphere can be absorbed by growing things and sequestered for years. Definitive evidence shows that excess carbon dioxide can contribute to the greenhouse effect and speed global warming. Similarly, tropical forests also act as a primary producer of oxygen. In the respiration process that absorbs gaseous carbon dioxide, trees and other plants give off oxygen. It is for these and a host of other reasons ...
2001-04-19
Crack growth in welded turbine materials at elevated temperatures
International Nuclear Information System (INIS)
Due to thermal gradients and load changes steam-turbine casings suffer combined creep-fatigue loading. Creep and fatigue portions depend on service conditions. Special interest is focused on the behaviour of creep-fatigue cracks, originated from potential defects due to construction and manufacturing weldments, on residual lifetime assessment. The project deals with the crack-growth behaviour at 530deg C and r.t. of welded and unwelded heat-resistant cast steels: 1% CrMoV-cast (GS-17 CrMoV 5 11, two melts: low and high V-content) and 12% CrMoV-cast (G-X 22 CrMoV 12 1). The crack planes of CT-specimens investigated, taken from manual arc-welded plates, were situated in the heat-affected zone (HAZ). The fatigue, creep and combined creep-fatigue crack-growth behaviour was investigated by means of low-frequency (0.5 and 0.05 Hz) tests, holding-time (20 min) tests and constant load tests up to about 5 000 h. Metallographic investigations show that in the case of both 1% and 12% CrMoV-cast ...
1989-12-01
Energy Technology Data Exchange (ETDEWEB)
Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging caused by the build up of carbonaceous or ...
1981-09-01
Calibration of cylindrical detectors using a simplified theoretical approach
Energy Technology Data Exchange (ETDEWEB)
The calibration of cylindrical detectors using different types of radioactive sources is a matter of routine. The most accurate method, that of experiment, is limited by several factors when the energy interval is broad, requiring a relatively large number of primary standards, implying considerable investment of money and time. Several other techniques can be used instead, including Monte Carlo simulations and semi-empirical methods. Calculations based on the first technique require good definition of the geometry and materials, including the dead layer and window thickness together with an accurate set of cross-sections. The second technique requires two different types of experimental input, the first being from use of sources emitting cascade {gamma} rays and the second from use of sources emitting isolated {gamma} rays in order to cover the wide energy range and provide coincidence-summing corrections, respectively. Here, we introduce a new theoretical approach based on the Direct ...
2006-09-15
CWTC business plan; Wind turbine component centre
Energy Technology Data Exchange (ETDEWEB)
This report presents the Business Plan for the establishment of the Wind Turbine Component Centre (CWTC) to meet the objectives of performing theoretical research and experimental testing. The core idea of a CWTC is to support the Danish wind energy industry and research activities at the component level improving the competitive advantage of that industry. The CWTC will in itself operate its activities, including access to test and experimental facilities, on a semi commercial basis. The business model for the CWTC presented is based on revenues coming from component manufacturers as well as research grants, and will include membership fees as well as hourly payment and larger projects where payment is a limited project sum. The presented roadmap model clarifies the development path towards a fully developed CWTC, which will cover test of all important components along the drive-train as well as offering a comprehensive systematic understanding of the entire ...
2011-04-15
Energy Technology Data Exchange (ETDEWEB)
Spectroscopic constants and absolute intensities from more than 2150 transitions belonging to 52 bands of 7 isotopic species of carbon dioxide have been determined using a multispectrum nonlinear least-squares fitting technique. The spectral data (0.01 cm{sup -1} resolution) were obtained at room temperature and low pressure (<10 Torr) using the McMath-Pierce Fourier transform spectrometer of the National Solar Observatory on Kitt Peak, Arizona. A natural sample of carbon dioxide with absorption path lengths between 24 and 385m were used in recording the spectra. The first measurements have been made of the theoretically predicted 2v{sub 2}{sup 2} 2+v{sub 3} {open_quotes}forbidden{close_quotes} band of {sup 12}CO{sub 2}. Two bands which have not been predicted so far, one belonging to {sup 13}CO{sub 2} and the other to {sup 13}C{sup 16}O{sup 18}O, have been identified. The measured line intensities obtained for each band have been analyzed to determine the ...
1995-12-31
Bound states in the quantum scalar electrodynamics
International Nuclear Information System (INIS)
The next relativistic correction to #alpha# to for bound state mass of two charged scalar particles is calculated in the quantum scalar electrodynamics by the functional integral method. Contribution of the ''nonphysical'' time variable turned out to be important and leads to nonanalytic dependence of the bound state mass on #alpha#. In conclusion, one can say that the functional approach is the best mathematical representation to preserve the gauge invariance. The lowest approximation of this functional representation is the pure nonrelativistic Feynman path integral representation of the nonrelativistic Schroedinger equation. The functional integral representation shows that any regular series for next corrections to #alpha# does not exist and these corrections cannot be reduced to some terms of the nonrelativistic potential in the Schroedinger picture. In other words, the ''nonphysical'' time coordinate is important and leads to corrections which are not ...
Energy Technology Data Exchange (ETDEWEB)
This thesis is devoted to studies which prepared the construction of an atom Mach-Zehnder interferometer. In such an interferometer, the propagating waves are spatially separated, and the internal state of the atom is not modified. The beam-splitters are diffraction gratings, consisting of standing optical waves near-resonant with an atomic transition. We use the Bloch functions to define the atom wave inside the standing wave grating and thus explain the diffraction process in different cases. We developed a nearly all-analytical model for the propagation of an atom wave inside a Mach-Zehnder interferometer. The contrast of the signal is studied for many cases: phase or amplitude gratings, effects of extra paths, effects of the main mismatches, monochromatic or lightly polychromatic sources. Finally, we discuss three interferometric measurements we think very interesting. The first, the index of refraction of gas for atomic waves, is studied in detail, with ...
1999-12-01
Energy Technology Data Exchange (ETDEWEB)
The 1977 version of the Simpson-Puls-Dutton model appears to be the most amenable with respect to utilizing known or readily estimated quantities. The Pardee-Paton model requires extensive calculations involving estimated quantities. Recent observations by Koike and Suzuki on vanadium support the general assumption that crack growth in hydride forming metals is determined by the rate of hydride formation, and their hydrogen atmosphere-displacive transformation model is of potential interest in explaining hydrogen embrittlement in ferrous alloys as well as hydride formers. The discontinuous nature of cracking due to hydrogen embrittlement appears to depend very strongly on localized stress intensities, thereby pointing to the role of microstructure in influencing crack initiation, fracture mode and crack path. The initiation of hydrogen induced failures over relatively short periods of time can be characterized with fair reliability using measurements of the ...
1982-04-01
An environmentally sustainable transport system in Sweden. A scenario study
Energy Technology Data Exchange (ETDEWEB)
This is a short version of a scenario study concerning the possibilities to reach an Environmentally Sustainable Transport system in Sweden in a perspective of 30 years. The aim of the scenario study has been to describe one of several possible paths from today`s transport system to an environmentally adopted one. However, this does not imply that the task is to predict how such a transformation can be accomplished. The aim is rather to illustrate what such transformation require in the form of political decisions. The transformation of the transport system in to an environmentally adopted one, is primarily treated as a political problem, and a political perspective has accordingly been chosen for the study. In this English version of the scenario, the carbon dioxide problem is used to illuminate the many conflicts in goals and other problem that will attend an environmental adoption of the Swedish transport system, and to highlight the analytical points of ...
1997-02-01
Advanced Lighting Program Development (BG9702800) Final Report
Energy Technology Data Exchange (ETDEWEB)
The report presents a long-range plan for a broad-based, coordinated research, development and market transformation program for reducing the lighting energy intensities in commercial and residential buildings in California without compromising lighting quality. An effective program to advance lighting energy efficiency in California must be based on an understanding that lighting is a mature field and the lighting industry has developed many specialized products that meet a wide variety of light needs for different building types. Above all else, the lighting field is diverse and there are applications for a wide range of lighting products, systems, and strategies. Given the range of existing lighting solutions, an effective energy efficient lighting research portfolio must be broad-based and diverse to match the diversity of the lighting market itself. The belief that there is one solution--a magic bullet, such as a better lamp, for example--that will propel lighting efficiency ...
1998-02-01
One of the biggest fears and challenges a parent of a child with special needs faces is navigating the post-22 landscape. When a child hits the age of 22, the Department of Elementary and Secondary Education (DESE) is no longer required to provide daily services and support. Whatever the abilities, or disabilities, of a child, every parent has the same concerns about how their child will productively fill their days and live as independently as possible without the safety net of the DESE. One of the transition paths most frequented is entering the workforce. Public and private schools alike work to teach their students the basic skills they need to work. In fact, the national Individuals with Disabilities Education Act (IDEA) states that students must have a transition plan in formulation by the age of 16. This article describes the vocational program developed by the League School of Greater Boston which specifically addresses the challenges students, their ...
2010-10-01
A phenomenological finite element model of stereolithography processing
Energy Technology Data Exchange (ETDEWEB)
In the stereolithography process, three dimensional parts are built layer by layer using a laser to selectively cure slices of a photocurable resin, one on top of another. As the laser spot passes over the surface of the resin, the ensuing chemical reaction causes the resin to shrink and stiffen during solidification. When laser paths cross or when new layers are cured on top of existing layers, residual stresses are generated as the cure shrinkage of the freshly gelled resin is constrained by the adjoining previously-cured material. These internal stresses can cause curling in the compliant material. A capability for performing finite element analyses of the stereolithography process has been developed. Although no attempt has been made to incorporate all the physics of the process, a numerical platform suitable for such development has been established. A methodology and code architecture have been structured to allow finite elements to be birthed (activated) ...
1996-03-01
A model for the calculation of vent clearing transients in pressure suppression systems
International Nuclear Information System (INIS)
For the layout of a pressure suppression system of a light water cooled reactor (boiling water reactor) it is important to know the time dependent behavior of the vent clearing transient after a loss-of-coolant accident for two main reasons: time of the end of the vent clearing transient influences strongly the pressure and temperature maxima in the drywell and wetwell. Time-dependent behavior of the vent clearing transient influences pressure loads in the condensation pool of the wetwell and therefore pressure induced stresses to the structure. The time-dependent behavior of the water masses in the vent pipes and wetwell are described by the basic equations for a nonstationary incompressible friction flow: momentum equation, continuity equation and a correlation for the variation of the state of the gas volume in the wetwell above the water level. After many algebraic operations and integrations along the flow path, a single ordinary nonlinear differential ...
1975-09-01
"Eztrack": A single-vehicle deterministic tracking algorithm
Energy Technology Data Exchange (ETDEWEB)
A variety of surveillance operations require the ability to track vehicles over a long period of time using sequences of images taken from a camera mounted on an airborne or similar platform. In order to be able to see and track a vehicle for any length of time, either a persistent surveillance imager is needed that can image wide fields of view over a long time-span or a highly maneuverable smaller field-of-view imager is needed that can follow the vehicle of interest. The algorithm described here was designed for the persistence surveillance case. In turns out that most vehicle tracking algorithms described in the literature[1,2,3,4] are designed for higher frame rates (> 5 FPS) and relatively short ground sampling distances (GSD) and resolutions ({approx} few cm to a couple tens of cm). But for our datasets, we are restricted to lower resolutions and GSD's ({ge}0.5 m) and limited frame-rates ({le}2.0 Hz). As a consequence, we designed our own simple approach in IDL ...
2007-12-20
Paul Scherrer Institut Scientific Report 2001. Volume V: General Energy
Energy Technology Data Exchange (ETDEWEB)
Major advances in 'Energy and Materials Cycles' have been achieved in the removal of heavy metals from the solid residues of municipal waste incineration. It has been conclusively shown that the oxidation/reduction conditions established during the thermal treatment of filter ash have a decisive influence on the evaporation of groups of heavy metals. With respect to biomass gasification, studies have been carried out with respect to the best way of extracting pure hydrogen from the low calorific value gas that is typically obtained from a biomass gasifier. The overarching goal of the laboratory 'High Temperature Solar Technology' is the use of solar energy for the production of solar fuels, or for the reduction of CO{sub 2} emissions in large scale industrial processes that are conventionally carried out with the use of fossil fuels. In a short-term project targeted at the solar production of lime, highly encouraging results (98% degree of ...
2002-03-01
Energy Technology Data Exchange (ETDEWEB)
SKB is currently performing site investigations at two potential sites for a final repository for spent nuclear fuel. This report presents results of water flow and solute transport modelling of the Forsmark site. The modelling reported in this document focused on the near-surface groundwater, i.e. groundwater in Quaternary deposits and shallow rock, and surface water systems, and was performed using the MIKE SHE tool. The most recent site data used in the modelling were delivered in the Forsmark 2.3 dataset, which had its 'data freeze' on March 31, 2007. The present modelling is performed in support of the final version of the Forsmark site description that is produced during the site investigation phase. In this work, the hydrological modelling system MIKE SHE has been used to describe near-surface groundwater flow and the contact between groundwater and surface water at the Forsmark site. The surface water system at Forsmark is described with the one-dimensional ...
2008-09-15
Contaminant transport in fracture networks with heterogeneous rock matrices. The Picnic code
Energy Technology Data Exchange (ETDEWEB)
In the context of safety assessment of radioactive waste repositories, complex radionuclide transport models covering key safety-relevant processes play a major role. In recent Swiss safety assessments, such as Kristallin-I, an important drawback was the limitation in geosphere modelling capability to account for geosphere heterogeneities. In marked contrast to this limitation in modelling capabilities, great effort has been put into investigating the heterogeneity of the geosphere as it impacts on hydrology. Structural geological methods have been used to look at the geometry of the flow paths on a small scale and the diffusion and sorption properties of different rock materials have been investigated. This huge amount of information could however be only partially applied in geosphere transport modelling. To make use of these investigations the 'PICNIC project' was established as a joint cooperation of PSI/Nagra and QuantiSci to provide a new ...
2001-02-01
Energy Technology Data Exchange (ETDEWEB)
Within the Annual Conference 2009 of the VGB PowerTech e.V. (Essen, Federal Republic of Germany) from 23rd to 25th May, 2009, in Lyon (France) the following lectures were held: (1) Electricity demand, consequences of the financial and economic crisis - Current overview 2020 for the EU-27 (Hans ten Berge); (2) Status and perspectives of the electricity generation mix in France (Bernard Dupraz); (3) European electricity grid - status and perspective (Dominique Maillard); (4) Technologies and acceptance in the European energy market (Gordon MacKerran); (5) EPR construction in Finland, China, France, (Claude Jaouen); (6) EPR Flamanville 3: A project on the path towards nuclear revival (Jacques Alary); (7) Worldwide nuclear Revival and acceptance (Luc Geraets); (8) An overview on the status of final disposal of radioactive wastes worldwide (Piet Zuidema); (9) Who needs pumped storage plants? PSP are partner to grid stability and renewable energies (Hans-Christoph ...
2009-07-01
International Nuclear Information System (INIS)
Within the Annual Conference 2009 of the VGB PowerTech e.V. (Essen, Federal Republic of Germany) from 23rd to 25th May, 2009, in Lyon (France) the following lectures were held: (1) Electricity demand, consequences of the financial and economic crisis - Current overview 2020 for the EU-27 (Hans ten Berge); (2) Status and perspectives of the electricity generation mix in France (Bernard Dupraz); (3) European electricity grid - status and perspective (Dominique Maillard); (4) Technologies and acceptance in the European energy market (Gordon MacKerran); (5) EPR construction in Finland, China, France, (Claude Jaouen); (6) EPR Flamanville 3: A project on the path towards nuclear revival (Jacques Alary); (7) Worldwide nuclear Revival and acceptance (Luc Geraets); (8) An overview on the status of final disposal of radioactive wastes worldwide (Piet Zuidema); (9) Who needs pumped storage plants? PSP are partner to grid stability and renewable energies (Hans-Christoph ...
2009-09-23
CFD investigation of balcony spill plumes in atria
Energy Technology Data Exchange (ETDEWEB)
Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production rate of the buoyant fire plume. One design issue is the smoke production rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes are based on a combination of one-tenth scale test data and theoretical analysis. Questions have arisen over the suitability of these correlations for real-scale designs. A combined program of full-scale experimentation and CFD modeling is being conducted to analyze the accuracy of these correlations. A full-scale experimental facility was constructed with a 5 m by 5 m by 15 m fire compartment connected to a four-story atrium. Propane fires in the compartment produce balcony ...
2004-07-01
CFD investigation of balcony spill plumes in atria
International Nuclear Information System (INIS)
Smoke management in buildings during fire events often uses mechanical ventilation systems to maintain smoke layer elevation above a safe evacuation path. Design of these systems requires accurate correlations for the smoke production rate of the buoyant fire plume. One design issue is the smoke production rate of fire plumes which spill out from a fire compartment, under a balcony and up through an atrium or other large volume. Current engineering correlations for these balcony spill plumes are based on a combination of one-tenth scale test data and theoretical analysis. Questions have arisen over the suitability of these correlations for real-scale designs. A combined program of full-scale experimentation and CFD modeling is being conducted to analyze the accuracy of these correlations. A full-scale experimental facility was constructed with a 5 m by 5 m by 15 m fire compartment connected to a four-story atrium. Propane fires in the compartment produce balcony ...
2004-05-09
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
