Science.gov (United States)

An evaluation was made of possible hazardous working conditions at the ASARCO Globe facility, Denver, Colorado. The facility was involved in the recovery of cadmium from baghouse dust, a waste byproduct of nonferrous smelters. A medical study of kidney function was conducted in 45 current or former cadmium production workers; results were compared to those for 35 hospital workers. Kidney abnormalities were more common and more severe in the cadmium workers than in the hospital workers. Abnormalities of proximal tubular function included reduced reabsorption of beta-2-microglobulin, retinol binding protein, calcium and phosphate. Glomerular dysfunction was evidenced as elevated serum creatinine. As length of exposure to cadmium increased, changes became more apparent in workers. No reversal of the ...

CERN Document Server

The development of a replacement to the conventional film based X-ray imaging technique is required for many reasons. One possible route for this is the use of a large area film of a suitable semiconductor overlaid on an amorphous silicon readout array. A suitable semiconductor exists in cadmium telluride and its tertiary alloy cadmium zinc telluride. In this thesis the spectroscopic characteristics of commercially available CZT X- and gamma-radiation detectors are established. The electronic, optical, electro-optic, structural and compositional properties of these detectors are then investigated. The attained data is used to infer a greater understanding for the carrier transport in a CZT radiation detector following the interaction of a high energy photon. Following this a method used to fabricate large area films of CdTe on a commercial scale is described. This is cathodic electrodeposition from an aqueous electrolyte. ...

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

International Nuclear Information System (INIS)

Ten different alloys of zirconium have been tested with regard to the effect of irradiation on their mechanical properties and their sensitivity to environmentally induced failure. Two different environments were used: iodine vapour and liquid cesium with an addition of 2% cadmium. The neutron dose was 10"2"1n/cm"2 (E>1MeV) and the irradiation temperature was about 300 degrees C. All alloy additions increased the irradiation hardening. Especially notable was the large effect of titanium and tin on irradiation hardening. A limited amount of transmission electron microscopy was carried out in order to find an explanation to the effects. The testing in different environments showed that there is no clear correlation between environmental sensitivity and yield stress. For materials of similar yield stress an alloyed material tends to be more sensitive to environmental cracking than a material which only ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The pitting behavior of Alloy 800 was investigated as a function of temperature and prefilming in high temperature water. The pitting behavior was characterized in terms of the pitting potential and the pit density. The pitting potential decreases with increasing temperature and chloride activity. Prefilming of test coupons over a time period between 100 and 5,000 hours in ammoniated water at 300 C has no apparent influence on the pitting potential at room temperature, 180 C and 300 C. However, the number of pits in prefilmed coupons is much higher than in coupons covered with an air passive layer. The effect of prefilming on pit nucleation was investigated in more detail with regard to a model and test methods developed by Bianchi and co-workers. Density of pits in prefilmed coupons is at least one order of magnitude higher than in air passive coupons. Maximum pit density was measured after a prefilming period of 1 00 hours. The effect is ...

Energy Technology Data Exchange (ETDEWEB)

Investigations of cadmium toxicity to microorganisms are now more concerned with the interactions of cadmium with different environmental factors and other metals. The interactions are complex and have not been thoroughly studied yet. Metal interactions may assume the form of synergism characterized by increase in toxicity, but also of antagonism in which one metal reduces the toxicity of another. Apart from cadmium interactions with such toxic metals as mercury and lead, interactions of cadmium with the essential trace elements seem to be very interesting because it has been assumed that algal cells take up cadmium by the system transporting these elements. A previous study showed that cadmium transport into Stichococcus bacillaris cells was inhibited by Mn/sup 2 +/ ions. Thus, it can be supported that there exist some possibilities of using those ions ...

International Nuclear Information System (INIS)

... cadmium sulfides communications electrons performance testing physical

International Science & Technology Center (ISTC)

Elaboration of Electrochemical Solar Energy Converter Incorporating Cadmium Selenide Semiconductor Developed Electrochemically

UK PubMed Central (United Kingdom)

A multispecialty panel of physicians evaluated a case series of 53 composite-materials workers in a large aircraft manufacturing facility who filed workers' compensation claims for illness labeled by...Full Text Available

International Nuclear Information System (INIS)

The thermal-neutron capture cross section (#sigma#_0_,_g) and the resonance integral (I_0_,_g) leading to the ground state of "2"4"2Am were measured by an activation method for neutron capture by "2"4"1Am. A method with gadolinium, which was similar to the cadmium difference method, was used to measure the cross section #sigma#_0_,_g with attention to resonances of "2"4"1Am. Americium chloride samples containing "2"4"1Am radioisotope were irradiated for 68 h in the long-irradiation plug of the Kyoto University Research Reactor, KUR. Wires of Co/Al and Au/Al alloys were used as monitors to determine thermal-neutron fluxes and epithermal Westcott's indexes at the irradiation positions. An #alpha#-ray spectrometer was used to measure the activity ratios of "2"4"2Cm to "2"4"1Am. On the basis of Westcott's convention, the #sigma#_0_,_g and I_0_,_g values were determined as 628#+-#22 b and 3.5#+-#0.3 kb, respectively. (author)

Science.gov (United States)

PMID:21121206

Science.gov (United States)

In 1963, Grover and co-workers at the Los Alamos. Scientific. Laboratory ...... and A. P. Watkins. (1986) "The Computation of Compressible ...

UK PubMed Central (United Kingdom)

Populus yunnanensis was employed as a model species to detect sexual differences in growth, physiological, biochemical, and ultrastructural responses to cadmium (Cd) stress, nitrogen...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundEvidence on human semen quality as it relates to exposure to various metals, both essential (e.g., zinc, copper) and nonessential (e.g., cadmium, lead), is inconsistent....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A solar cell structure is produced by a method comprising baking the solar cell, containing a gridded top layer of cuprous sulfide formed on a base of cadmium sulfide, for 20 minutes to 10 hours, to produce a copper doped cds electrically insulating region in the cadmium sulfide base near the interface of the cuprous sulfide and the cadmium sulfide; removing the cuprous sulfide, and the copper doped cds insulating region not covered by the grid, to provide a bare cadmium sulfide areas; and then forming a cuprous sulfide layer on the exposed areas not covered by the grid.

International Nuclear Information System (INIS)

... bismuth chlorides bismuth 207 cadmium chlorides efficiency evaporation high

International Nuclear Information System (INIS)

The paper reports the recovery of zinc and cadmium following 6.1 MeV alpha particle irradiation at 4.2 K as studied by means of electrical reistivity measurements. Specimens of 10 #mu#m thick have been used in order to obtain a homogeneous defect distribution over the whole thickness of the specimen. The pre-irradiation resistivity ratios were 700 and 750 for cadmium and zinc, respectively. (Auth.).

UK PubMed Central (United Kingdom)

Cadmium (Cd) exposure causes glucosuria (glucose in the urine). Previously, it was shown that Cd exposure of primary cultures of mouse kidney cells (PMKC) decreased mRNA levels of the glucose...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Heavy metals discharged from industries are a major source of pollution which has become a threat to all forms of life. Among the various heavy metals, cadmium is known to be highly toxic even in low concentrations. The harmful effects of cadmium is attributed to its effects on sulfhydryl groups of enzymes, especially dehydrogenases. Various aspects of cadmium pollution on fishes have been extensively reviewed. A survey of the literature reveals that few attempts have been made to study the various aspects of cadmium toxicity in crustaceans and these studies were mainly devoted to marine forms. The freshwater crustaceans, particularly the freshwater field crab, Barytelphusa guerini, has received little attention. The present study reports the influence of cadmium on certain aspects of protein metabolism in the tissues of a freshwater field crab, Barytelphusa guerini, and important ...

Energy Technology Data Exchange (ETDEWEB)

A sample of 30 manganese-exposed foundry workers from two Swedish plants were examined with a partly computerized psychological test battery, comprised of 10 performance tests. Performance of the manganese-exposed workers was compared to that of a matched control group of 60 workers. Matching criteria were age, geographical area, type of work, and the results on a test of verbal comprehension. Performance of the exposed workers was inferior to that of the control group on tests of simple reaction time, digit span, and finger tapping. No correlations were found between performance and the present manganese exposure levels or the number of years employed in manganese work. The results seem to indicate that the present exposure standards for manganese, in Sweden 2.5 mg/m3 and in most other countries 5 mg/m3, are not sufficient to protect workers from negative effects on performance ...

International Nuclear Information System (INIS)

Cadmium is an environmental toxic metal implicated in human diseases. The mechanism of its toxicity is not fully understood. Therefore, the role of cadmium in renal toxicity, and the protective role of selenium against this toxicity were investigated. Forty-five male rats were used through out the study and divided into three groups of 15. The first group received saline solution daily for 10 days. The second group, received cadmium chloride (CdCl_2) (2 mg/kg body weight) intraperitoneally daily for a period of 10 days. The third group, received sodium selenite (1 mg/kg body weight, twice a day) and CdCl_2 (once a day) for a period of 10 days. The results showed that cadmium treatment increased renal lipid peroxidation (measured as malondialdehyde, MDA) which was associated with a significant decrease in the antioxidant systems such as reduced glutathione levels and the activities of glutathione ...

UK PubMed Central (United Kingdom)

Two cases of pulmonary alveolar proteinosis, including one death, occurred in workers at a facility producing indium-tin oxide (ITO), a compound used in recent years to make flat panel displays. Both...Full Text Available

UK PubMed Central (United Kingdom)

The selection due to the "healthy worker effect" was estimated from a random sample of the total Finnish population. The sample of 20 000 people was followed for changes in occupations from 1960 to...Full Text Available

UK PubMed Central (United Kingdom)

Workers from cotton mills were exposed to cotton dust during carding in an experimental cardroom. Cotton from different geographical locations with varying amounts of endotoxin were used. Exposure levels...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVES--This case cohort study examines whether there is an association between exposure to electric and magnetic fields and suicide in a population of 21,744 male electrical utility workers from...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThe relationships between worker health and productivity are becoming clearer. However, few large scale studies have measured the direct and indirect cost...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Cadmium is a toxic, non-essential heavy metal inhibiting numerous enzymes with functional sulfhydryl groups. Among the animals, aquatic organisms are most sensitive to heavy metals. Various aspects of toxic effects of cadmium pollution on fishes have been extensively reviewed. Survey of literature reveals that relatively few attempts have been made on the various aspects of cadmium toxicity in crustaceans and these studies were mainly devoted to marine forms. The freshwater crustaceans, particularly the freshwater field crab, Barytelphusa guerini, received less attention. This crab forms one of the major components of the paddy field ecosystem and has an edible importance among local populations. Apart from this, these crabs are easily available, maintainable in the laboratory and data obtained in this study can be extrapolated to other crustaceans. The present study reports the influence of cadmium on ...

Energy Technology Data Exchange (ETDEWEB)

Taconite tailings and their component asbestiform minerals in Lake Superior water had no demonstrable effect on the chronic toxicity of cadmium to the flagfish, Jordanella floridae. Maximum acceptable toxicant concentrations determined in life cycle tests, where effects on survival, growth, reproduction, and bioconcentration were used as endpoints, were between 3.3 to 7.4, 3.0 to 6.5, and 3.4 to 7.3 micrograms cadmium/liter at 0.004, 0.08, and 0.95 mg/liter taconite tailings concentrations, respectively.

Science.gov (United States)

... Abstract : Cadmium telluride single crystals were subjected to multiple-energy boron ion implants with total doses up to 1.5 x 10 sq cm. ...

International Nuclear Information System (INIS)

Cadmium is a non-essential heavy metal found abundantly in the environment. Children of women exposed to cadmium during pregnancy display lower motor and perceptual abilities. High cadmium body burden in children is also related to impaired intelligence and lowered school achievement. However, little is known about the molecular and cellular basis of developmental neurotoxicity in the sensitive early life stages of animals. In this study, we explore neurological deficits caused by cadmium during early embryonic stages in zebrafish by examining regionalization of the neural tube, pattern formation and cell fate determination, commitment of proneural genes and induction of neurogenesis. We show that cadmium-treated embryos developed a smaller head with unclear boundaries between the brain subdivisions, particularly in the mid-hindbrain region. Embryos display normal anterior to ...

Energy Technology Data Exchange (ETDEWEB)

A new method for the separation and determination of trace amounts of cadmium and zinc in water as their thenoyltrifluoroacetone (TTA) complexes with dibenzo-18-crown-6 (DB18C6) in o-dichlorobenzene has been established by means of synergistic extraction and back-extraction combined with atomic absorption spectrometry. The effect of various factors (synergism with TTA and DB18C6, shaking time, composition of the extracted species, and mutual separation etc.) on the extraction and back-extraction of cadmium and zinc has been in- vestigated. When the mixtures were extracted for 4 min at pH 4.9, only zinc was extracted quantitatively, whereas cadmium remained in the aqueous phase. After the phases were separated, cadmium was again extracted quantitatively at pH 7.5. Then, the two phases were each shaken with 0.05-0.1 mol/l HCl in order to back-extract cadmium and zinc from the organic ...

Energy Technology Data Exchange (ETDEWEB)

Binding of Cd/sup 2 +/ ions in aqueous solutions of statistical copolymers of acrylamide with cadmium acrylate with different content of ionogenic groups in copolymers was investigated by polarography, conductometry, viscometry and dialysis. It is shown that the degree of binding of Cd/sup 2 +/ ions increases with increasing of the content of ionogenic groups in the copolymer and with decreasing of ionic strength of the solution. The values of the degree of binding of Cd/sup 2 +/ ions obtained by polarography and dialysis show satisfactory agreement.

International Nuclear Information System (INIS)

There is extensive evidence that exposure to asbestos causes pulmonary parenchyma fibrosis, pleural disease, and malignant neoplasm in asbestos-exposed workers. However, few data concerning brake-lining workers are available in the literature. In this study, we aimed to assess the long-term effects of chrysotile asbestos exposure on lung function and the risk of asbestos-related diseases in brake-lining workers. Seventy-four asbestos-exposed workers who processed brake-lining products and 12 unexposed office workers were offered pulmonary function tests (spirometry and transfer actor) in 1992 and 1999. In 1999, the mean duration of asbestos exposure was 0.00#+-#4.07 and 11.02#+-#4.81 years (7-31 years) in non smoking and smoking asbestos workers, respectively. Transfer factor (T_L, CO) and transfer coefficient (K_C_O) decline were significant in the 7-year ...

Energy Technology Data Exchange (ETDEWEB)

This document reports the results of the FY 2005 PNNL VPP Program Evaluation, which is a self-assessment of the operational and programmatic performance of the Laboratory related to worker safety and health. The report was compiled by a team of worker representatives and safety professionals who evaluated the Laboratory's worker safety and health programs on the basis of DOE-VPP criteria. The principle elements of DOE's VPP program are: Management Leadership, Employee Involvement, Worksite Analysis, Hazard Prevention and Control, and Safety and Health Training.

International Science & Technology Center (ISTC)

Determination of Special Molybdenum Alloys Optimal Structure Using the Cybernetic Method

International Science & Technology Center (ISTC)

Development of the Corrosion Protection Technology for Special Steels and Alloys

UK PubMed Central (United Kingdom)

A survey was carried out in a steel foundry in Brisbane to evaluate the nature and frequency of respiratory symptoms and to assess ventilatory function. The foundry used many moulding processes including...Full Text Available

Science.gov (United States)

... Problem: At a glass ceramic cooktop plant, workers manually lift uncut plates of glass onto a waist-high conveyor belt, where it is then stacked ...

International Nuclear Information System (INIS)

A method for enrichment of the ppb level of cadmium in water by using the coagulation of soybean protein by adding acids or its complex-forming character with heavy metal ions was investigated. After adding fixed amounts of soybean milk and 2% sodium diethyldithiocarbamate(DDTC) aqueous solution and a suitable amount of delta-gluconic lactone (delta-GL) to a sample solution, the mixture was heated to boiling in order to coagulate the protein. The coagulum(soybean curd) was separated from the suspension by centrifugation and burned to ashes with a low temperature plasma asher. Then the cadmium enriched in it was determined by atomic absorption spectrometry. Various factors such as the pH of the sample solution, the amounts of soybean milk and the collection additives, and the concentration of NaCl in the sample solution on the recovery of cadmium were examined systematically. The best recovery was obtained under the ...

Energy Technology Data Exchange (ETDEWEB)

The feather has been widely used as a indicator tissue of metal exposure in birds. The feathers were collected from Tuskegee University poultry farm (TUPF) and Harrison Poultry farm (HPF) chicken and analyzed by Inductively Coupled Plasma Atomic Emission Spectroscopy for lead, cadmium, cobalt, chromium, and copper contaminations. The mean levels of lead, cadmium, cobalt, chromium, and copper in TUPF chicken were 3.67, 0.13, 12.23, 0.22, and 7.71 ppm, respectively, and in HPF chicken were 5.32, 0.096, 11.03, 0.15, and 8.06 ppm, respectively. The mean levels of these metals did not show any significant difference between TUPF and HPF chicken.

UK PubMed Central (United Kingdom)

BackgroundComplaints of arm, neck and/or shoulders (CANS) affects millions of computer office workers. However its prevalence and associated risk factors in developing countries...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The 1993-1995 period represents a time of significant transition for workers engages in nuclear-related activities. Total nuclear-related employment fell markedly from about 300,000 workers in 1993 to 265, 000 in 1995, a 12% decline. This is the lowest level since the 1970s. In 1995, a third of all nuclear-related employment was in the reactor operation and maintenance segment. 6 figs, 1 table.

Energy Technology Data Exchange (ETDEWEB)

Collective dose equivalent and population dose from occupational exposures in Japan, 1988 were estimated on the basis of a nationwide survey. The survey was conducted on annual collective dose equivalents by sex, age group and type of radiation work for about 0.21 million workers except for the workers in nuclear power stations. The data on the workers in nuclear power stations were obtained from the official report of the Japan Nuclear Safety Commission. The total number of workers including nuclear power stations was estimated to be about 0.26 million. Radiation works were subdivided as follows: medical works including dental; non-atomic energy industry; research and education; atomic energy industry and nuclear power station. For the determination of effective dose equivalent and population dose, organ or tissue doses were measured with a phantom experiment. The resultant doses were compared with the ...

International Nuclear Information System (INIS)

Personal monitoring and dose assessment of all radiation workers is an essential regulatory requirement as per radiation safety procedures of AERB and operating stations. The occupational workers of TAPS 1 and 2 and TAPS 3 and 4 are monitored for internal contamination due to high energy gamma emitters by whole body counting

Science.gov (United States)

Thin film solar cells and solar cell testing - photovoltaic cells, radiation damage to cadmium sulfide solar cells, and airplane testing of solar cells

UK PubMed Central (United Kingdom)

Cell suspension cultures of tomato, Lycopersicon esculentum Mill. cv VFNT-Cherry, produce phytochelatins (poly[γ-glutamylcysteinyl]glycines) when exposed to cadmium. The synthesis...Full Text Available

Science.gov (United States)

Cadmium telluride single crystals were subjected to multiple-energy boron ion implants with total doses up to 1.5 x 10 sq cm. Various diagnostic techniques were used to assess the structural and electronic properties of these crystals in their as-implante...

Energy Technology Data Exchange (ETDEWEB)

Biosorption of the heavy metal ion Cd{sup 2+} by protonated nonliving brown alga Sargassum fluitans biomass was accompanied by the release of hydrogen protons from the biomass. The uptake of cadmium and the release of proton matched each other throughout the biosorption process. The end-point titration methodology was used to maintain the constant pH 4.0 for developing the dynamic sorption rate. The sorption isotherm could be well represented by the Langmuir sorption model. A mass transfer model assuming the intraparticle diffusion in a one-dimensional thin plate as a controlling step was developed to describe the overall biosorption rate of cadmium ions in flat seaweed biomass particles. The overall biosorption mathematical model equations were solved numerically yielding the effective diffusion coefficient D{sub e} about 3.5 {times} 10{sup {minus}6} cm{sup 2}/s. This value matches that obtained for the desorption process and is approximately ...

British Library Electronic Table of Contents (United Kingdom)

Cadmium sulfide particles have been synthesized in the aqueous medium using the amino acid histidine as a stabilizing agent. These particles demonstrate the phenomenon of size quantization effect. The fluorescence of histidine-stabilized CdS was found to be enhanced and quenched by the addition of DNA bases adenine and guanine, respectively. The fluorescence enhancement of CdS in the presence of adenine has been explained on the basis of interaction between the quantum dot stabilizer and the amino group of adenine. Quenching of CdS fluorescence by guanine occurs due to interaction of the substrate with the quantum dot surface.

Science.gov (United States)

Since 1901, ASARCO, Inc. has owned and operated an 89-acre cadmium-refining smelter in the Globeville neighborhood of north Denver, Colorado. According to complaints filed by EPA and local residents, operations at the smelter have allegedly contaminated the air, ground water, surface water, and soil; contamination from arsenic, cadmium, lead, and zinc has occurred both onsite and offsite. EPA proposed to add the site to the National Priorities List (NPL) in May 1993.

Science.gov (United States)

... MOLYBDENUM ALLOY GUN BARREL LINERS o0 in ... NEW POWDER TECHNOLOGIES FOR MOLYBDENUM ALLOY GUN BARREL LINERS ...

International Nuclear Information System (INIS)

... filters molybdenum alloys production sulfuric acid alloys chemical reactions ...

Energy Technology Data Exchange (ETDEWEB)

A cross-sectional medical examination of a copper smelter work force included determination of blood lead (Pb-B), zinc protoporphyrin (ZPP), blood cadmium (Cd-B), urinary cadmium (Cd-U), and urinary arsenic (As-U), since it was known that such metal impurities were present in the copper concentrate. A total of 776 copper smelter employees (680 active and 96 retirees and ex-employees) were examined. Another 144 men, never employed in the smelter, but who had worked in copper mines (and sometimes in gold mines) were also examined. Mean Pb-B, ZPP, Cd-B, and As-U were significantly higher in active copper smelter employees than in retirees or miners, indicating exposure and absorption in the copper smelter. Significant correlations between Pb-B and Cd-B, and Cd-U and As-U were present, confirming the common source of absorption. Although there was evidence for an increased lead absorption, this was very moderate, with practically no Pb-B levels in ...

International Nuclear Information System (INIS)

Results of hot cracking on welds with compositions between alloy 800 and AWS ER NiCr 3. Investigation of the influence of Si, Mn, Ti and Al on the hot cracking suscpetibility of the alloy 800. (orig.).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

Alloys are described which contain nickel, aluminum, boron, iron and in some instances manganese, niobium and titanium.

Energy Technology Data Exchange (ETDEWEB)

Radiation doses to workers at the Manhattan Engineer District (MED) and US Atomic Energy Commission (AEC) sites due to external irradiation during 1940--1960 are reviewed. Categorized radiation dose data were available from AEC annual reports for some years. Annual individual radiation dose data for ten MED/AEC sites for all years were available from the US Department of Energy`s (DOE) Comprehensive Epidemiologic Data Resource (CEDR). These data are combined to produce an estimate of external collective dose equivalent to 172,000 person-rems (1720 person-Sv) for 1940--1960. During this period there were 41 overexposures, 19 criticality incidents, and 3 deaths due to acute radiation syndrome among several hundred thousand workers.

Energy Technology Data Exchange (ETDEWEB)

Due to the well-establish corrosion problems of Alloy 600 as a steam-generator material and the subsequent focus on thermally treated (TT) Alloy 690 and Alloy 800 as alternative materials, a systematic analysis of the corrosion behavior of these two latter alloys is warranted. Corrosion test results for Alloys 690 TT and 800 were collected and organized in the form of corrosion mode diagrams. Selected data for mill annealed (MA) Alloy 600 were also included for reference. The corrosion mode diagrams correlate the modes of corrosion degradation observed in tests as functions of the environment pH and electrochemical potential (ECP). The diagrams confirm that Alloys 690TT shows some susceptibility in caustic environments, and Alloy 800 shows susceptibility in both caustic and highly acidic environments. (authors). 6 figs., ...

UK PubMed Central (United Kingdom)

BackgroundTo investigate the feasibility, the ease of implementation, and the extent to which community health workers with little experience of data collection could be trained...Full Text Available

UK PubMed Central (United Kingdom)

This article reports on an exploratory study of hospice social workers’ assessment and collaborative practices related to pain management; especially caregiver concerns about patient...Full Text Available

UK PubMed Central (United Kingdom)

Two men reported previously with vitiligo after occupational exposure to hydroquinone monomethyl ether (HMME) have been reviewed after eight years. Repigmentation of significant degree was found in...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundSeveral aromatic amines (AA) could cause bladder cancer and are an occupational hygiene problem in the workplace. However, little is known about the percutaneous absorption...Full Text Available

UK PubMed Central (United Kingdom)

Benzidine (4,4'-diaminobiphenyl) is a known human carcinogen; exposure to this substance resulted in an epidemic of bladder cancer among workers in the dye industry in Europe and North America. The...Full Text Available

UK PubMed Central (United Kingdom)

The possible contribution to urinary mutagenicity of occupational exposures in the rubber industry was studied by assaying the urine concentrates of 72 workmen (44 smokers) employed in a tyre plant....Full Text Available

UK PubMed Central (United Kingdom)

Results of the toxicological studies of working conditions, general and professional morbidity, and complex examinations carried out on workers engaged in the production of polyamides, polyacrylonitrile...Full Text Available

UK PubMed Central (United Kingdom)

An assessment has been made of biochemical alterations in renal and hepatic functions of 73 male operators employed for an average of 8.2 years (range 0.5-23 years) in a chemical plant producing chlorinated...Full Text Available

Wastenet

... In recent years workers in this field have focused on nucleation by nano-porous materials . This was in part motivated by a theoretical study by Page and Sear (2006) who proposed a two step model for nucleation in pores which suggest that there is ...

Science.gov (United States)

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose o...

Energy Technology Data Exchange (ETDEWEB)

An analysis of the mortality of workers employed at the Commissariat a l'Energie Atomique (CEA) between 1946 and 1994 is presented. Standardized Mortality Ratios (SMR) are computed with reference to the French national population for the period 1968-1994. 51 286 workers are included in the study. 3 784 deaths occurred between 1968 and 1994. A healthy worker effect is observed for men (SMR=0.53 Cl{sub 90%}=[0.52; 0.55]) and for women (SMR=0.70 Cl{sub 90%}=[0.64; 0.76]). An excess is observed for male pleural cancers (SMR=1.54, Cl{sub 90%}=[1.03; 2.21]). An excess of breast cancer is observed among women, statistically significant for the 1980-1994 period (SMR=1.30, Cl{sub 90%}=[1.04; 1.61]). An excess is observed for malignant melanoma for both sexes (SMR=1.38, Cl{sub 90%}=[0.95; 1.96]), stronger for the 1990-1994 period (SMR=2.11, Cl{sub 90%}=[1.25; 3.34]). It diminishes with age. (orig.)

UK PubMed Central (United Kingdom)

A survey was conducted at 15 textile plants with dyehouses in western Sweden. Employees with a history of work related rhinitis, asthma, or skin symptoms were offered a clinical and immunological investigation...Full Text Available

International Nuclear Information System (INIS)

Glutathione (GSH) depletion sensitizes human lung carcinoma (A549-T27) cells to the cytotoxic effects of Cd++. The effects of GSH depletion on Cd++ accumulation and Cd++-induced metallothionein (MT) content were investigated to determine the possible role of these Cd++ responses in the sensitization process. Cellular GSH was depleted to 20% to 25% of control levels with buthionine sulfoximine (BSO), or diethyl maleate (DEM), respectively. Neither treatment significantly affected Cd++-induced accumulation of exogenous 35s-cysteine into intracellular MT in a dose-dependent fashion. The results indicate that neither enhanced Cd++ accumulation nor reduced MT synthesis plays a primary role in affecting enhanced Cd++ cytotoxicity in A549 cells with reduced GSH levels. Although BSO inhibition of GSH synthesis enhanced MT synthesis, it sensitized the cells to Cd++, which suggests an additive effect of GSH and MT in cadmium cytoprotection. This observation also raises the ...

International Nuclear Information System (INIS)

The low cycle fatigue testing was carried out to provide a basis for comparison of the behavior of the two kinds of Alloy 800 (low carbon Alloy 800 and high carbon Alloy 800H). The testing was done at temperatures of 500"0C and 650"0C either with or without hold. The results obtained were as follows: (1) At 650"0C, the low-cycle fatigue life was essentially the same for the two alloys on the basis of strain amplitude, but Alloy 800H had a longer life on the basis of stress amplitude. (2) At 500"0C, the two alloys exhibited longer lives than at 650"0C, with Alloy 800 exhibiting 2-3 times longer life than Alloy 800H when compared on the basis of plastic strain range. At this temperature the stress range showed the maximum for Alloy 800H. (3) When a creep effect was introduced either by way of a hold ...

International Nuclear Information System (INIS)

The possibilities of using both selective heavy ion induced X-ray emission and secondary ion mass spectroscopy (SIMS), for the identification of impurities present at low concentrations in cadmium telluride are examined. The relative concentrations of the impurities along CdTe crystals have been determined by exciting the X-ray emission of the elements in several slices with Ar and Kr ions and by comparing the relative characteristic X-ray emission yields. As a consequence of the quasimolecular inner shell ionization mechanism in heavy ion-atom collisions, Ar and Kr ions allow a strong excitation of the main impurities seen by SIMS namely Si, Cl and Ge, As, with only a minor contribution of Cd and Te. From the changes of the concentrations of the various impurities along the crystal, informations about segregation coefficients and compensation can be obtained.

Energy Technology Data Exchange (ETDEWEB)

Biosorption behaviour of and toxic effects of heavy metals in submersed and immobilised microorganisms was studied in batches and in continuous processes in an airlift-recycle reactor. Nickel, cadmium, and zinc were used as heavy metals. (orig./VHE) [Deutsch] Am Beispiel einer Naphthalin-2-sulfonsaeure-abbauenden Kultur wurde das Biosorptionsverhalten und die toxische Wirkung von Schwermetallen auf submerse und immobilisierte Mikroorganismen im Batch-Ansatz und im kontinuierlichen Betrieb in einem Airlift-Schlaufenreaktor untersucht. Als Schwermetalle wurden Nickel, Cadmium und Zink eingesetzt. (orig./VHE)

British Library Electronic Table of Contents (United Kingdom)

Purpose Two main pathways of phytoremediation of heavy metal-contaminated soils are phytostabilization and phytoextraction. Some soil amendments can strengthen phytostabilization or phytoextraction through either reducing heavy metal bioavailability in soil or increasing the heavy metal accumulation capacity of the hyperaccumulator (enhancing heavy metal concentration or shoot biomass of the hyperaccumulator). Urea and chicken manure are often used as fertilizers. This research will explore their effects on a newly found hyperaccumulator, Rorippa globosa (Turcz.) Thell., phytoremediating cadmium (Cd). Materials and methods Pot culture experiment was conducted to study the accumulation characteristics of R. globosa at different Cd contamination concentrations under one fertilizer level (1?g...

International Nuclear Information System (INIS)

A method is described for determination of aluminium, cadmium, cobalt, chromium, copper, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, zinc, titanium and vanadium in iron ore. After dissolution, a 1 gram sample of iron ore is applied to a column of AGI-X8 anion exchange resin (chloride form), in 100 ml of 7M HCl. Aluminium, chromium, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, titanium and vanadium are eluted with 7M HCl; iron, copper and cobalt are eluted with 0.5M HCl; cadmium and zinc are eluted with 2M HNO_3. Iron is subsequently removed from copper and cobalt by a solvent extraction with methyl isobutyl ketone. The elements are determined in the eluates by atomic absorption spectrometry, except for titanium and vanadium, which are determined spectrophotometrically.

British Library Electronic Table of Contents (United Kingdom)

To reconstruct the profiles of heavy metal levels in the South Ocean ecosystem of Antarctica, the concentrations of lead (Pb), copper (Cu), arsenic (As), cadmium (Cd), and zinc (Zn) in seal hairs and lake sediments spanning the past 1500?years from Fildes Peninsula of King George Island and in weathering lake sediments from Nelson Island of West Antarctica were determined. The lead contents in the seal hairs and the weathering sediments show a sharp increase since the late 1800s, very likely due to anthropogenic contamination from modern industries. After the 1980s, the Pb content in seal hairs dropped by one-third, apparently due to the reduced usage of leaded gasoline in the Southern Hemisphere. Copper arises mainly from the weathering process, and its level may be substantially affected...

International Nuclear Information System (INIS)

The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep tests at 650{degrees}C and 172 MPa was conducted on the base alloy which contained 40Nb-40-Ti-10Al-10Cr. A second alloy was modified with 0.11 at. % carbon and 0.07 at. % yttrium. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1100{degrees}C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1000{degrees}C, and for the modified alloy at room temperature, 400, 600, 700, and 800{degrees}C. Oxidation ...

International Nuclear Information System (INIS)

Investigated are the characteristics of high-temperature plastic deformation the velocity sensitivity of flow stresses, deformation curves, flow stresses, deformation before rupture - as well as the structure of beryllium alloys containing nickel (0.5-4 %), yttrium (0.5-2 %) and aluminium (38 %). The alloys containing nickel (2%) and yttrium (0.5 %) are superplastic, however, deformation before fracture of the alloys is lower than that of the unalloyed beryllium. The singularities of high-temperature plastic flow of the alloys and the causes of deterioration of their plasticity are determined.

Energy Technology Data Exchange (ETDEWEB)

Since 1991, secondary side cracking has become a major concern in EDF steam generators. At 350 C, IGSCC of Alloy 600 was found in pure NaOH solutions from 4 to 500 g/l, with a maximum at 100 g/l. From the present results and available data, IGSCC of Alloy 690 occurred in pure NaOH solutions from 40 to 500 g/l, but the greatest sensitivity was observed at 100 g/l. TG/IGSCC of Alloy 800 became more severe with increasing NaOH solutions, from 10 to 500 g/l. On the whole, the ranking for SCC-resistance was Alloy 600 < Alloy 800 < Alloy 690. A significant improvement was still obtained with 690TT with intergranular carbides (industrial tubes) and perhaps with Alloy 800 NG (nuclear grade), but both alloys cracked at the highest stresses. IGSCC susceptibility of Alloy 600 MA was higher for the tubes ...

International Nuclear Information System (INIS)

Three model boilers, manufactured to simulate full-size tube sheet crevices, were tested with various secondary side environments. The first was faulted with organics representative of the decomposition of humic acid. The second was faulted with sodium carbonate and sodium hydroxide, while the third was faulted with sodium sulfate and sodium hydroxide. Each model contained seven tubes, which included Alloy 600 in the mill-annealed (MA) and thermally-treated (TT) conditions and Alloy 690 in the thermally-treated condition. Two models contained Alloy 800 tubes in the mill-annealed condition and one had Alloy 800 in the mill-annealed/cold-worked/glass-bead-peened condition. Two different sizes of tubesheet crevices were used in all model boilers. In the organics-faulted boiler, tubes of Alloy 600MA, Alloy 690TT and Alloy 800MA experienced no ...

Energy Technology Data Exchange (ETDEWEB)

AZ31 and experimental ZMA611 alloys were strip cast into 2 mm thick strips. The as-cast AZ31 alloy strip consists of columnar dendrites. On the other hand, as-cast ZMA611 alloy strip shows equiaxed dendritic structure through the thickness of strip. These alloys were subjected to various thermomechanical treatments and their tensile properties were evaluated. Strip cast AZ31 alloy in H24 condition has equivalent yield and tensile strengths with similar ductility compared to commercial ingot cast AZ31-H24 alloy, indicating that strip casting is a viable process for the fabrication of Mg alloy strips. The ZMA611 alloy has a large volume fraction of fine dispersoid particles in the microstructure, resulting from the beneficial effect of strip casting on microstructural refinement. It has been shown that the ZMA611 ...

Energy Technology Data Exchange (ETDEWEB)

Resistance of ALLOY 800 as a PWR/SG tubings to IGC/IGSCC and Ni, Co release into high temperature water was evaluated as compared with ALLOYs 600 and 690. The study to improve the resistance to IGSCC and general corrosion was also made. From the results, ALLOY 800 was evaluated to be the most reliable among the high Ni alloys tested. In addition, the alloy would obtain further reliability in IGSCC and general corrosion resistance by the combined addition of Ti and Nb, and the prior oxidation treatments, respectively. (author).

Science.gov (United States)

... Accession Number : ADD151811. Title : Ultra High Strength Beta Titanium Alloy for Fasteners. Descriptive Note : Journal article,. ...

Science.gov (United States)

... Accession Number : ADD109273. Title : THERMAL STABILITY OF ALPHA-BETA TITANIUM ALLOY Ti-5Al-2Cr-1Fe,. Corporate Author : ...

Science.gov (United States)

... by the boron doping in most of the alloys except for Al66Mn9Zr25 + 50 ppm B alloy; permanent deformation at ultimate compressive strength is not ...

International Nuclear Information System (INIS)

The nickel-rich superalloys Alloy 600 and Alloy 800 have been corroded in mildly alkaline deuterated aqueous conditions typical of secondary coolant circuits in a nuclear power station. The oxide films and substrates of these alloys have been analysed by imaging SIMS depth profiling, which makes it possible to describe elemental distribution in all three dimensions. The measurement of the distribution of the secondary ions NiO"-, FeO"- and CrO"- appears useful for detailing the behaviour of nickel, iron and chromium within oxidized phases. The measurement of D"- distribution outlines the extent of oxide hydration. For Alloy 800, evidence of sodium migration into the grain boundaries of the alloy substrate is found. For Alloy 600, no grain boundary sodium ingress can be identified under comparable corrosion conditions. (author).

Energy Technology Data Exchange (ETDEWEB)

Four low activation alloy classes, two austenitic and two ferritic, have been incorporated into the MOTA-1B experiment in the FFTF reactor to provide an early assessment of the suitability of such alloys for reactor service.

International Nuclear Information System (INIS)

The effect of various hydrogen concentrations on the crystal lattice period and the hardness of titanium alloy was examined, the alloy containing about 16 at.% Mo (27.5 wt. % Mo) and having #beta# structure. The peculiar features of the mechanism of plastic deformation of the alloy were studied after adding hydrogen to it. A dependence of the crystal lattice period on the concentration of hydrogen was obtained for TixMoxH_2 alloy. It has been established that the hardness of the Ti-Mo alloy does not change when hydrogen is added to it. The presence of hydrogen introduces changes into the mechanism of deformation of #beta#-titanium alloy. The configuration of the inverse pole figures after rolling proves that the transverse slip process in an alloy with hydrogen is hampered, and that the coplanar slip process is developing in it.

Science.gov (United States)

... CLOSURE DURING HOT WORKING OF AN ALPHA/BETA TITANIUM ALLOY (PREPRINT) ... HOT WORKING OF AN ALPHA/BETA TITANIUM ALLOY ...

Science.gov (United States)

... Accession Number : ADD336001. Title : Development of a FeCoNb Alloy to be used in Eddy Current Probes for Testing Ferromagnetic Tubes,. ...

Science.gov (United States)

... Title : DUCTILITY RATIO OF AGED BETA TITANIUM ALLOY. Corporate Author : NEW YORK UNIV NY SCHOOL OF ENGINEERING AND SCIENCE. ...

International Nuclear Information System (INIS)

Stemming from their unique combination of elevated strength, low density, and good overall corrosion resistance, beta titanium alloys have become attractive candidate materials for critical, high-stress, components in corrosive services. An overview of the comparative corrosion resistance of beta alloys to conventional alpha and alpha/beta titanium alloys in common industrial and aerospace service environments generally reveals attractive behavior depending on the environment and alloy composition and, in some cases, alloy condition. Expanded performance windows are especially noted for the molybdenum-rich beta alloys, particularly in regard to resisting reducing acids, stress corrosion, and high temperature localized chloride attack, along with hydrogen and oxidation resistance. Where applicable, implications of this enhanced corrosion performance on current ...

UK PubMed Central (United Kingdom)

Materials with high electrical conductivity and optical transparency are needed for future flat panel display, solar energy, and other opto-electronic technologies. In_xCd_1-xO...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The levels of four different heavy metals [cadmium (Cd), lead (Pb), chromium (Cr) and copper (Cu)] were determined in various vegetables [leek (Allium ampeloprasum), sweet basil (Ocimum basilicum), parsley (Petroselium cripsum), gardem cress (lepidium sativum) and tarragon (Artemisia dracuncullus)] cultivated around the Sanandaj city. (Author)

Energy Technology Data Exchange (ETDEWEB)

The results of Sandia National Laboratories' participation in the NASA Planetary Definition and Design Program are summarized. Areas reported include the characterization of large area cadmium zinc telluride spectrometers and the application of simulation techniques to the prediction of device performance. Also investigated was the response of mercuric iodide devices in the region from 1 to 100 KeV. A literature study to determine the status or radiation damage measurements in room temperature semiconductor devices is also reported.

International Nuclear Information System (INIS)

The population doses and risks of stochastic effects from occupational exposures in Japan in 1978 were estimated on the basis of a nation-wide survey. The survey was conducted on annual collective dose equivalents by sex, age group and type of radiation work for about 82,500 workers other than the workers in nuclear power stations. The data on the workers in nuclear power stations were obtained from the offitial publication of the Japan Nuclear Safety Commission. The total number of workers except for nuclear power stations was estimated to be about 170,000 persons. Radiation works were subdivided as follows: medical works including dental; nondestructive inspectional; non-atomic energy industrial; research and educational; atomic energy industrial and nuclear power industrial. The annual collective dose equivalents were estimated to be about 6,000 man rem for medical workers, 450 ...

Energy Technology Data Exchange (ETDEWEB)

Whereas supersaturated aluminum alloys demonstrate enhanced passivity, conventional aluminum alloys spontaneously pit in air-saturated chloride solutions. We have concentrated on three areas: evaluation and characterization of Al-W alloys, which exhibit the best corrosion performance of any alloy system studied to date; characterization of the passive-film structure of Al-Mo alloys; and production and characterization of Al-W and Al-Ta powders, which will be used for compaction into bulk material. Surface analysis of the Al-W passive films formed during polarization show surprising little oxidized solute compared to other alloys. These results indicate that the barrier layer formation and electrostatic repulsion mechanisms used to explain the passivity of other alloys are not involved here. Instead the W may act to stabilize the passive film ...

International Nuclear Information System (INIS)

In-reactor testing of bolt-loaded compact tension specimens was performed in 360 C water to determine the irradiation-assisted stress corrosion cracking (IASCC) behavior of HTH Alloy X-750 and direct-aged Alloy 625. New data confirm previous results showing that high irradiation levels reduce SCC resistance in Alloy X-750. Heat-to-heat variability correlates with boron content, with low boron heats showing improved IASCC properties. Alloy 625 is resistant to IASCC, as no cracking was observed in any Alloy 625 specimens. Microstructural, microchemical and deformation studies were performed to characterize the mechanisms responsible for IASCC in Alloy X-750 and the lack of an effect in Alloy 625. The mechanisms under investigation are: boron transmutation effects, radiation-induced changes in microstructure and deformation characteristics, and ...

International Nuclear Information System (INIS)

To clarify the acidic and alkaline Intergranular Stress Corrosion Cracking (IGSCC) mechanism of thermally treated alloy 690 (alloy 690 TT) and shot peened alloy 800 (alloy 800 SP), C-ring tests were conducted in deaerated HCl solutions and in deaerated NaOH solutions at 350degC, compared with the acidic and the alkaline IGSCC susceptibilities of mill-annealed alloy 600 (alloy 600 MA), full-sensitized one (alloy 600 FS) and thermally treated one (alloy 600 TT). Grain boundary characteristics, such as chromium depleted zone and chromium carbide precipitation, were examined using modified Huey test and Transmission Electron Microscopy. Potential-pH diagram for Ni, Cr, Fe-H_2O system at 350degC was constructed and the solubilities of NiO, Cr_2O_3 and Fe_3O_4 were also calculated to evaluate the stability of oxide films which ...

Science.gov (United States)

Potential exposure of workers to phosphide was examined during an in-depth industrial hygiene survey at the Bunge Corporation, in Kansas City, Kansas, where the gas was used as a grain fumigant. During the study, 14 men were employed at the facility. Tablets of aluminum phosphide were added to the grain mass for fumigation. General dilution ventilation resulted from outside air entering the work areas through ventilation louvers; there was also a local-exhaust ventilation system. Air samples revealed that, when the fumigant dispensers were being filled, workers in the area had significant exposure. At the time of the survey the relative humidity in the facility was high, permitting the reaction to phosphide to occur more readily. The levels of phosphide and respirable dust were reasonably low in the elevators, suggesting that the ventilation system was adequate. The author recommends that workers filling the dispenser with ...

British Library Electronic Table of Contents (United Kingdom)

As the HIV/AIDS epidemic and the spread of sexually transmitted infections (STIs) in China has come to the forefront of public health attention, female sex workers (FSWs) and their clients (CFSWs) are becoming increasingly important to HIV/STI prevention efforts. This secondary analysis uses data abstracted from the Chinese Health and Family Life Survey 1999-2000 to report prevalence rates of two STIs as well as sexual risk behaviors for CFSWs - men who paid for sex with FSWs in the past 12 months - in comparison with men who had not patronized FSWs. Among 1879 Chinese CFSWs who completed anonymous interviews and urine testing, 152 (6.3%, weighted) said they had paid for sex in the past 12 months and 18.8% of CFSWs (weighted) tested positive for gonorrhea. CFSWs were 10 times more likely t...

Science.gov (United States)

The threshold stress itensities for stress corrosion crack propagation in beta titanium alloy 38-6-44, Ti-3Al-8V-6Cr-4Mo-4Zr, has been determined in salt water and methanolic solutions. The alloy was immune to stress corrosion cracking in aqueous sodium c...

Science.gov (United States)

This paper reports Palladium alloy compositions investigated for suitability as a nonreactive material for the processing of ceramic superconductors. Barium-based superconductors were tested on Pd-Au and Pd-Ag alloys for reactivity. Bismuth-based superconductors were tested on a Pd-Ag alloy. The least reactive was found to be 70% Pd-30% Ag for the barium-based high-temperature superconductors (HTSC), whereas 30% Pd-70% Ag was found to be least reactive for bismuth-based HTSC.

Energy Technology Data Exchange (ETDEWEB)

The surface properties of copper-refractory metal (CU-RF) alloy bodies are modified by heat treatments which cause the refractory metal to form a coating on the exterior surfaces of the alloy body. The alloys have a copper matrix with particles or dendrites of the refractory metal dispersed therein, which may be niobium, vanadium, tantalum, chromium, molybdenum, or tungsten. The surface properties of the bodies are changed from those of copper to that of the refractory metal.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

General corrosion behavior of ALLOY 800 in high temperature water was studied in relation to its surface film structure. The surface film formed in water was found to decrease the corrosion rate of ALLOY 800. This film is composed of Ni ferrite, and can be obtained by oxidation in air or steam. Based on these results, air or steam oxidation treatment to inhibit Ni and Co release of ALLOY 800 into high temperature water is proposed. (author).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

This paper describes a process for the direct production of a superconductive niobium-titanium alloy during reduction of niobium pentoxide. It comprises: mixing at least one of titanium metal powder and titanium dioxide powder with niobium pentoxide powder and aluminum powder; heating the resulting mixture to form a niobium-titanium alloy and a slag consisting essentially of aluminum oxide; and separating the alloy and the slag.

Energy Technology Data Exchange (ETDEWEB)

Simulated atmospheric corrosion studies were performed to determine the corrosion protection provided by galvanized zinc coatings on depleted uranium, U-0.75 Ti alloy, and U-6 Nb alloys. The accelerated ASTM tests consisted of exposing the galvanized samples to aqueous and aqueous chloride environments. The test results showed that anodic protection was provided by the electronegative zinc coatings on uranium and uranium alloys. Treating zinc with chromate conversion coatings also provided more protection.

International Nuclear Information System (INIS)

A new high strength titanium alloy has been developed primarily intended for fastener applications. While Ti-6Al-4V is used extensively as a fastener alloy in the aerospace industry, its shear strength allowable is limited to 655 MPa (95 ksi). For higher shear strength requirements, various steels or nickel-based alloys are used (up to 860 MPa (125 ksi)), but with the attendant density penalty. This new alloy is intended to provide the 860 MPa shear strength at roughly a 40% weight savings. After screening various alloy systems, the optimum chemistry has been selected as follows: Ti-6.0V-6.2Mo-5.7Fe-3Al. In light of its 125 ksi shear strength goal, the alloy has been designated TIMETAL reg-sign 125.

International Nuclear Information System (INIS)

In order to substitute expensive cast titanium alloys by powder ones the possibility of introduction of powder additions by mechanical stock mixing is studied. It is shown that microstructure of powder alloys of Ti-Zr(1-9%) system is typical for one-phase cast #alpha#-alloys. The Ti-Mo(1-9%) and Ti-Nb(1-9%) system alloys have microstructure typical for two-phase (#alpha#+#beta#)-alloys. For homogeneous structure to be obtained the high temprature annealing is advisable after hot pressing. Alloying with Mo, Zr and Nb permits to increase considerable the strength of powder titanium products (at 9% Mo more than two times).

Energy Technology Data Exchange (ETDEWEB)

In this book over 250 alloys are organized by AISI number into 10 major sections: Irons, Carbon Steels, Alloy Steels, Low Alloy Constructional Steels, Ultra High Strength Steels, Tool Steels, Maraging Steels, Wrought Stainless Steels, Heat Resistnat Casting Alloys, and Iron Based Rought Superalloys. Each alloy record lists the designation, specifications, UNS number, composition, product forms and a comment on the high-temperature properties and applications. Referenced data is then given for physical properties such as density, specific heat, thermal conductivity, thermal expansion, electrical conductivity, Poisson's ratio, moduli of elasticity and rigidity, etc. Mechanical properties follow, and include tensile properties, shearing and bearing properties, impact properties, creep, stress rupture and stress relaxation and fatigue properties. The last part of the ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys show a high specific strength and are therefore increasingly used for light-weight constructions in transportation industry.{sup [1,2]} To predict the behaviour of the material under the influence of cyclic loading it is vital to understand the fatigue behaviour of magnesium alloys. Only when understood properly, it is possible to fully apply the potential weight reduction by using magnesium alloys. A very important aspect in fatigue of magnesium alloys is the influence of a corrosive media and elevated temperatures, of which both are relevant in automotive applications. These two factors tend to have deleterious effects on magnesium alloys and therefore also have to be considered in investigations on the fatigue behaviour of magnesium alloys. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

International Nuclear Information System (INIS)

Tarapur Atomic Power Station unit-4 is first 540 MWe pressurized heavy water reactor. Heavy water is used as the coolant and moderator. With reactor operation tritium is formed by absorption of neutron by Deuterium atoms. Experience in the 220 MWe indicates that tritium is main contributor to the internal dose of radiation workers. Study on Tritium build up in Primary Heat Transport (PHT) and Moderator (MOD) system was carried out at the initial stage of the operation of the unit-3 and 4. This paper brings out tritium activity buildup in the PHT and MOD systems and its comparison with 220 MWe reactors. This paper helps in estimation of the internal dose contribution to the radiation workers at TAPS 3 and 4. (author)

British Library Electronic Table of Contents (United Kingdom)

Abstract The aim of this paper is to provide an explanation to why the degree of informal employment may vary substantially between different regions within a country. In Brazil, 45% of workers in the urban labor force are employed informally. The degree of informal employment, however, varies substantially across regions, with some cities having 20% and others having 80% or more of their labor force in the informal sector. The hypothesis assessed here is that the quality of local governance-or government effectiveness-affects the decisions of workers and businesses as to whether to participate in the formal or the informal sector. The empirical analysis, based on data from 5500 Brazilian municipalities, shows that informal employment is lower in regions with better governance, higher aver...

CERN Document Server

Standard micro-economics concentrate on the description of markets but is seldom interested in production. Several economists discussed the concept of a firm, as opposed to an open labour market where entrepreneurs would recrute workers on the occasion of each business opportunity. Coase \\cite{Coase} is one of them, who explains the existence of firms as institution because they reduce the transaction costs with respect to an open labour market. Whatever the rationale proposed by economists to account for the existence of firms, their perspective is based on efficiency and cost analysis. Little attention is paid to the dynamics of emergence and evolution of firms. The aim of the present manuscript is to check the global dynamical properties of a very simple model based on bounded rationality and reinforcement learning. Workers and managers are localised on a lattice and they choose collaborators on the basis of the success of previous work ...

International Nuclear Information System (INIS)

The threshold stress intensities for stress corrosion crack propagation in beta titanium alloy 38-6-44, Ti3Al-8V-6Cr-4Mo-4Zr, has been determined in salt water and methanolic solutions. The alloy was immune to stress corrosion cracking (SCC) in aqueous sodium chloride solutions (marine atmosphere). However, in methanolic solutions, the alloy was very susceptible to SCC. This marked susceptibility in methanolic solutions can be mitigated by the addition of an inhibitor: sodium nitrate. Crack extension in the alloy was transgranular and failure occurred by brittle quasi-cleavage in methanolic solutions.

International Nuclear Information System (INIS)

By the methods of microstructural and electron-microscopic analyses by the tension test and impact test studied is the effect of quenching conditions on structure and mechanical properties of the TS6 titanium-#beta# alloy. It is shown that low temperature quenching from 700 deg C, recommended earlier for analogous VT15 titanium alloy, leads to appearence of intercrystalline fracture and to sharp decrease of impact strength of the TS6 alloy. Established are optimum conditions for quenching of half-finished products and articles of the TS6 alloy depending on their subsequent working or operation.

International Nuclear Information System (INIS)

Cr_2O_3 scales are found to form on Alloy 800 and a similar pure ternary alloy in air, and 1 and 50 atm. helium containing oxidizing impurities typical of those in an SGHTR. The strong temperature dependence and neglibible helium overpressure dependence indicate that gas transport through the scales is not rate controlling. Surface oxidation rates are therefore controlled by solid state diffusion and the low oxygen partial pressure dependence of the oxidation rate in Alloy 800 is ascribed to the presence of extrinsic defects in the Cr_3O_3 (due to doping by alloying elements) or to the presence of short circuit diffusion paths. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

The time-temperature-precipitation diagrams and the resulting time-temperature-sensitization diagrams have been established and are presented for today's current nickel-chromium-molybdenum alloys C-4, C-276, 22 and the recently developed alloy 59. Compared to those materials alloy 625 behaves differently due to its high niobium content. In addition, also the precipitation and sensitization of alloy G-3 has been established. Under the materials considered alloy C-276 has the strongest tendency to precipitate the intermetallics Mu and P together with the carbide M{sub 6}C at intermediate temperatures, followed by the alloys 22 and 59. The tendency to sensitization in the sense of the 50{mu}m (2 mils) intercrystalline penetration criterion when exposed to the ASTM G-28, method A test solution is greatest with alloy C-276, and decreases ...

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the role of amorphous SiO{sub 2} particles in corrosion and wear resistance of Ni-based metal matrix composite alloying layer, the amorphous nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer has been prepared by double glow plasma alloying on AISI 316L stainless steel surface, where Ni/amorphous nano-SiO{sub 2} was firstly predeposited by brush plating. The composition and microstructure of the nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer were analyzed by using SEM, TEM and XRD. The results indicated that the composite alloying layer consisted of {gamma}-phase and amorphous nano-SiO{sub 2} particles, and under alloying temperature (1000 deg. C) condition, the nano-SiO{sub 2} particles were uniformly distributed in the alloying layer and still kept the amorphous structure. ...

Energy Technology Data Exchange (ETDEWEB)

In our continued efforts for improving the performance of zinc anodes for a Zn/air battery, we now report the preparation of three alloys and improved performances of anodes made up with these alloys. The alloys contained zinc, nickel, and indium with different weight percentages and were calcined at two different temperatures. Out of the six alloys, the alloy which has a composition of zinc 90%, nickel 7.5% and Indium 2.5% and fired at 500{sup o}C is found to be the best. In the case of the hydrogen evolution reaction, this alloy had its potential shifted to a more negative potential. As far as the cyclic voltammograms were concerned, the difference between the anodic and cathodic part was minimal when compared with other alloys. Surprisingly, this alloy had reversibility even after 100 cycles of the cyclic ...

Energy Technology Data Exchange (ETDEWEB)

A series of cyclic strain controlled tests have been carried out at 600/sup 0/C on three high temperature austenitic iron-based alloys, AISI type 316 stainless steel, Alloy 800 H and Sandvik 253 MA. The tests were carried out under constant total strain control using a constant strain rate of 0.005 s/sup -1/. By considering the changes in modulus throughout the life of each specimen it was found that damage evolution could be successfully predicted as a function of plastic strain range despite the fact that each alloy had been chosen because of a different stress response at 600/sup 0/C. Although each alloy accumulated fatigue damage in a similar manner the longer lives of Sandvik 253 MA and Alloy 800 H at a given total strain range were due to a smaller plastic strain component and a reduced stage I crack propagation rate. In the 253 MA alloy, slip was ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties of Fe-Mn-Al ...

International Nuclear Information System (INIS)

The philosophy of containing tritium and activated products very close to the source and of operating by remote techniques is justified by a comparison with other concepts on protection and availability points of view. Several design options are studied according to the optimization protection methodology of ICRP. Provided that an important technological development is accomplished, the utilization of robotics and the limitation of containment volumes should be generalized.

Energy Technology Data Exchange (ETDEWEB)

The effective half-life based on urine bioassay results of Wolsung NPP's worker was calculated. The effective half-life for tritiated water vapour obtained was 5 {approx} 9 days. In comparison to 10 days reported for ICRP-30, it is lower than the corresponding half-life for Reference Man. Also, the half-life was calculated based on intake amount of daily water. According to this result, the metabolism was reviewed.

Energy Technology Data Exchange (ETDEWEB)

Reports by U.S. workers on geodetic measurements of recent plate motions or crustal deformation published in 1987-1990 are reviewed. The review begins with global plate motions, proceeds through plate boundaries in California, Alaska, and the Pacific Northwest, and finishes with volcanic phenomena, monument stability and longevity, and GPS relative position measurements. 184 refs.

UK PubMed Central (United Kingdom)

BackgroundSouth Africa has a high tuberculosis (TB)-human immunodeficiency virus (HIV) coinfection rate of 73%, yet only 46% of TB patients are tested for HIV. To date, relatively...Full Text Available

International Nuclear Information System (INIS)

This work presents and describes the natural radioactive occurrence in oil facilities. The origins of the detected radioactivity and the reasons of its settlement are discussed. The measurements results carried out in oil facilities in the Neuquina basin (Argentine) are shown in this work. The aim is to describe the actual situation and to evaluate the magnitude of the problem. Finally, recommendations are proposed to protect the health of the workers, especially of those who carry out the cleaning of the equipment, and to guarantee an appropriate final disposal for the generated radioactive residuals. (author)

Science.gov (United States)

Suggests that knowledge work is a useful way of characterizing important changes in the nature of work across a range of different occupational and professional groups. Discusses the implications through a conflict-based analysis that highlights the inherent conflict between "knowing" as part of the work experience and "knowledge" as an economic commodity. (Author/CCM)

UK PubMed Central (United Kingdom)

Summary20 years ago, in 1987, Edelson and co-workers published their first report on the effectiveness of a new procedure, called extracorporeal photochemotherapy (ECP), in patients...Full Text Available

International Nuclear Information System (INIS)

The purpose of the present study was to examine the in vitro effects of low-dose cadmium (Cd) on developing cortical cells. The cortical cells removed from fetuses (embryonic day 15) were treated with 10 nM of Cd for 24 h. The effects of Cd on dendritic and synaptic development were immunocytochemically observed with anti-microtubule associated protein-2 (MAP2) and anti-synapsin I antibodies, respectively. Administration of Cd suppressed dendritic as well as synaptic development at 10 nM. By two-dimensional gel electrophoresis and liquid chromatography-tandem mass spectrometric (LC/MS/MS) analysis, we identified three proteins with different expression after Cd-treatment; dihydropyrimidinase-related protein 2 (DRP-2/CRMP-2), 14-3-3-epsillon and calmodulin (CaM). Though the number of identified proteins was small, these proteins are known to be involved in neuronal development. The present study demonstrated the morphological effects as well as affected proteins in ...

CERN Document Server

Cadmium telluride (CdTe) and cadmium zinc telluride (CdZnTe) have been regarded as promising semiconductor materials for hard X-ray and Gamma-ray detection. The high atomic number of the materials (Z_{Cd} =48, Z_{Te} =52) gives a high quantum efficiency in comparison with Si. The large band-gap energy (Eg ~ 1.5 eV) allows us to operate the detector at room temperature. However, a considerable amount of charge loss in these detectors produces a reduced energy resolution. This problem arises due to the low mobility and short lifetime of holes. Recently, significant improvements have been achieved to improve the spectral properties based on the advances in the production of crystals and in the design of electrodes. In this overview talk, we summarize (1) advantages and disadvantages of CdTe and CdZnTe semiconductor detectors and (2) technique for improving energy resolution and photopeak efficiencies. Applications of these imaging detectors in ...

Energy Technology Data Exchange (ETDEWEB)

The construction and use of a portable, microprocessor controlled anodic stripping voltameter for on-site simultaneous metal analysis of copper, lead and cadmium in tap water is discussed. The instrumental system is comprised of a programmable controller which permits keying in analytical parameters such as sparge time and plating time: a rotating cell for efficient oxygen removal and amalgam formation; and, data handling via a minicomputer or analog pen recorder. Plating and stripping potentials are controlled by a digital potentiostat; stripping is done using a staircase waveform with measurement of the current after a one msec delay. In this way charging current effects are minimized. Results of tap water analysis showed 3 +- 1 ..mu..g/L lead, 22 +- 0.3 ..mu..g/L copper, and less than 0.2 ..mu..g/L cadmium for a Berkeley, California tap water, and 1-1000 ..mu..g/L Cu, 1 -2 ..mu..g/L Pb for ten samples of Seattle, Washington tap water. ...

CERN Document Server

This dissertation describes the evaluation of many-pixel Cadmium-Zinc-Telluride (CdZnTe) hard-X-ray detectors for future use with the High Energy Replicated Optics (HERO) telescope being developed at Marshall Space Flight Center. The detector requirements for the HERO application are good energy resolution (sufficient to resolve cyclotron features and nuclear lines), spatial resolution of ∼200 μm, minimal charge loss of absorbed X rays, and minimal sensitivity to the background environment. This research concentrates on assessing the suitability of these detectors for the focus of HERO, and includes the development of a simulation of the physics involved in an X-ray-detector interaction, a study of the intrinsic material properties, measurements with prototype detectors such as the energy and spatial resolution, charge loss, and X-ray background reduction through 3-dimensional depth sensing. Two types of detectors were available for evaluation. The ...

Energy Technology Data Exchange (ETDEWEB)

To reconstruct the profiles of heavy metal levels in the South Ocean ecosystem of Antarctica, the concentrations of lead (Pb), copper (Cu), arsenic (As), cadmium (Cd), and zinc (Zn) in seal hairs and lake sediments spanning the past 1500 years from Fildes Peninsula of King George Island and in weathering lake sediments from Nelson Island of West Antarctica were determined. The lead contents in the seal hairs and the weathering sediments show a sharp increase since the late 1800s, very likely due to anthropogenic contamination from modern industries. After the 1980s, the Pb content in seal hairs dropped by one-third, apparently due to the reduced usage of leaded gasoline in the Southern Hemisphere. Copper arises mainly from the weathering process, and its level may be substantially affected by climatic conditions. The concentrations of Cd, As, and Zn do not show any clear temporal trends.

International Nuclear Information System (INIS)

Single-crystalline cadmium selenide nanoparticles were obtained using high-temperature solution phase synthesis (HTSPS) synthesis. X-Ray powder diffraction and transmission electron microscopy were used to confirm the crystallinity and morphology of the resulting nanoparticles. To study the action of CdSe on antioxidant activity, we selected two biotechnological important strains of microalgae: cyanobacteria Spirulina platensis and red microalgae Porphyridium cruentum. In the case of Porphyridium cruentum, the obtained results demonstrated an increase in the productivity. For Spirulina platensis, the presence of the compound in the cultivating medium decreased the productivity of cyanobacteria.

International Nuclear Information System (INIS)

A number of herbal drugs are used in the Unani (Greco-Arab) System of Medicine for cardiovascular diseases. The herbs were analyzed by flame AAS and ICP-AES to determine if their therapeutic actions can be associated with the elements present in them. Cadmium, cobalt, chromium, copper, iron, potassium, magnesium, manganese, sodium, nickel, phosphorus, lead and zinc were some of the elements which play various roles in cardiovascular affections. An effort was made to correlate the role of these elements in cardiac diseases. (Auth.). 2 tabs., 32 refs.

British Library Electronic Table of Contents (United Kingdom)

Abstract Introduction - It is estimated that about 70-80% of the world's population relies on non-conventional medicine, mainly of herbal origin. However, owing to the nature and sources of herbal medicines, they are sometimes contaminated with toxic heavy metals such as lead, arsenic, mercury and cadmium, which impose serious health risks to consumers. It is critical to analyse source materials for heavy metals in order to ensure that their concentrations meet the related standards or regulations limiting their concentrations in herbal medicines. In this review, different analytical methods for analysis of heavy metals in herbal medicines are discussed. Objective - To provide a comprehensive review of the current state of the art in analytical methods used to detect heavy metals in herbal...

International Nuclear Information System (INIS)

Titanium base 'alpha'-alloys (Pt-7M, RK-20 and Ti-5Al-2Zr-1.5V) are considered for their behaviour under neutron irradiation. The role of alloying elements in radiation hardening is discussed depending of neutron fluence and irradiation temperature. For PK-20 alloy three stages of change in mechanical properties are revealed which are following: incubation period and weak hardening, intense radiation hardening, radiation hardening attenuation. Irradiation temperature rise results in an increase of incubation period and threshold neutron fluence. A special attention is paid to hydrogen absorption in #alpha#-titanium alloys under irradiation. It is concluded that titanium base 'alpha'-alloys are serviceable as structural materials in nuclear plants with allowance made for peculiar features of their radiation behaviour. 4 refs.; 7 figs.; 1 tab.

International Nuclear Information System (INIS)

In connection with the different cyclical strengths of the two-phase (#alpha# + #beta#) titanium alloy in the case of the acicular and rounded formations of the #alpha#-phase, we have studied, employing the X-ray diffraction method, the phase composition of the alloy and the influence of heat treatment upon it. Using the method of electronic fractography, we examined the fractures in samples destroyed by the asymmetric twisting, in order to find out why the durability of the alloy is dependent upon the #alpha# - phase structure. It has been found that in the BT22 alloy, the decay the #beta#-phase may proceed in two ways; either with the formation of the martensite #alpha#'-phase of the acicular shape or with the separation of the non-martensite round-shaped #alpha#-phase. The character of the phase transformations #beta# - #alpha# or #beta#-#alpha#' is, to a considerable extent, the conseguence of the ...

International Nuclear Information System (INIS)

Modern commercial alloys are not suited for future steam turbines of operating temperatures beyond 700 C. #gamma#'-hardened alloys like Waspaloy have good mechanical characteristics but have defects when large batches are melted. #gamma#'/#gamma#''-hardened alloys like Inconel 706, on the other hand, are easy to produce but have insufficient microstructural long-term stability and insufficient creep strength. Mixed crystal solidified alloys like Inconel 617 have excessive yield stress at forging temperatures. Two new alloys were therefore developed. Results so far show that they have good production characteristics but insufficient mechanical characteristics. The reasons for this are currently under investigation. (orig.)

International Nuclear Information System (INIS)

Nano indentation analysis and transmission electron microscopy observation were performed to investigate a microstructural evolution and its influence on the hardening behavior in Fe-Cr alloys after an irradiation with 8 MeV Fe4+ ions at room temperature. Nano indentation analysis shows that an irradiation induced hardening is generated more considerably in the Fe-15Cr alloy than in the Fe-5Cr alloy by the ion irradiation. TEM observation reveals a significant population of the a0 dislocation loops in the Fe-15Cr alloy and an agglomeration of the 1/2a0 dislocation loops in the Fe-5Cr alloy. The results indicate that the a0 dislocation loops will act as stronger obstacles to a dislocation motion than 1/2a0 dislocation loops.

International Nuclear Information System (INIS)

Resistance of Alloy 800 as a PWR S/G tube material to IGC/IGSCC and Ni, Co release into water was evaluated as compared with Alloys 600 and 690. The study to improve the resistance to IGSCC and general corrosion was also made, including the effects of shot-peening on the distribution of the residual stress of the U-bent tubes and the susceptibility to SCC, the stabilizing elements on IGC/IGSCC, and prior oxidation on general corrosion. From the results, shot-peened Alloy 800 was estimated to be the most reliable S/G tube material among the high nickel alloys tested. In addition, the Alloy 800 tube would obtain further reliability in IGSCC and general corrosion resistance by the combined addition of Ti, and Nb, and the prior oxidation of the inner tube surface, respectively.

Energy Technology Data Exchange (ETDEWEB)

Plastic formability of cast magnesium alloy that were hot rolled after roll strip casting was investigated to ascertain the feasibility of semi-solid strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Pd/Ag alloy hollow spheres have been synthesized in ethylene glycol solution by the solvothermal method and have been characterized extensively. TEM results have revealed the formation of Pd/Ag hollow spheres. Moreover, HRTEM results confirmed the formation of Pd/Ag alloy spheres, where the lattice fringe spacing is 0.229 nm corresponding to the (111) plane of Pd/Ag alloy. SEM, XRD and UV-vis results have further suggested the formation of alloy hollow spheres. The preliminary results showed the reaction time may be an importance factor influencing the formation of Pd/Ag alloy hollow spheres.

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

International Nuclear Information System (INIS)

Formation kinetics and composition of products of interaction of binary and ternary tungsten-molybdenum-rhenium alloys containing 30#+-#3 at.% (27-47 weight %) Re with products of thermal dissociation of ammonia and nitrogen-oxygeneous mixtures are studied. Mo-45% Re-10%W ternary alloy occupies intermediate position between W-27%Re and Mo-47%Re binary alloys, while its corrosion resistance and corrosion nature are close to those of W-Re and mechanical features - to those of Mo-Re alloy. It is explained by the fact, that the variation of W and Mo ration occurs in thin surface layer of ternary alloys in contrast to the initial state and the enrichment of near-the-surface layer with tungsten occurs under hot and cold deformation, at aging in the air, and during oxidation-reduction treatment. 4 refs.; 7 figs.

Energy Technology Data Exchange (ETDEWEB)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

International Nuclear Information System (INIS)

Preliminary observations on the isothermal carbon transfer in low-carbon Alloy-800 exposed in sodium with AISI-304 type of steel at 550_0 are reported. The alloy was found to undergo a carburization comparable or slightly lower than that observed for the AISI-304 stainless steel for carbon activities above 6 x 10 /sup -3/ at 550_0C, but was not found to decarburize below such a carbon activity value. In the examined range the chemical composition of the alloys does not affect the process out of the experimental uncertainty of measure. Conclusions concerning the effective diffusion for carbon in the alloy are formulated. Preliminary relationships were found for an empirical evaluation of the carburization of the Alloy-800 in sodium of known carbon activity.

International Nuclear Information System (INIS)

Recent advances made in the area of amorphous and nanocrystalline alloys exhibiting high saturation inductions are reviewed. A new chemical composition was identified that achieves a saturation induction of 1.64 T in an iron-based amorphous alloy. This alloy, when used in electrical transformers, shows a much improved performance over the existing amorphous alloy. Nanocrystalline FeCoCuNbSiB alloys are found to have saturation induction levels reaching 1.7 T. These materials are suited for use in sensors and inductors carrying large currents. Some of these nanocrystalline alloys show a BH squareness ratio exceeding 90%, which can be utilized in pulse power devices. Recent developments in the applications of these materials are also pointed out.

International Nuclear Information System (INIS)

Novel CdS hollow microspheres have been successfully synthesized via a facile template-free solution-phase reaction from cadmium nitrate and thioacetamide precursors. The morphology of CdS hollow microspheres depends strongly on the ratio between the precursors, cadmium nitrate to thioacetamide ratio. The physical properties of the hollow microspheres have systematically been studied by different characterization methods. The stoichiometry of the hollow microspheres studied by the energy dispersive X-ray diffraction spectroscopy confirmed that the synthesized CdS hollow microspheres are nearly stoichiometric bulk like CdS. The morphology of the hollow microspheres studied by high resolution scanning electron microscopy and transmission electron microscopy observations showed that the CdS hollow microspheres of the size of 2.5 ?m have hollow structure and are constructed by several nanoparticles of the size between 30 and 40 nm. The UV-visible ...

Energy Technology Data Exchange (ETDEWEB)

During the service in nuclear power plants, steam generator (SG) tubing will suffer from a vibration with a frequency from 30-40 Hz. This means that SG tubing will undergo a very high cycle fatigue process during the design life time (25 years=about 3x10{sup 10}cycles). The material degradation and the very high cycle fatigue life of SG tubing materials due to the vibration are therefore of concern. In this investigation, the fatigue properties of Alloy 690 and Alloy 800 SG tubing in the very high cycle fatigue regime (higher than 10{sup 7} cycles) and strain controlled fatigue at temperatures up to 330{sup o}C have been investigated. The fatigue properties of SG tubing of Alloy 690 are comparable to that of wrought material. The strain controlled fatigue properties of Alloy 690 and Alloy 800 are slightly better at 288{sup o}C than at room temperature (RT). At the stress near the ...

International Nuclear Information System (INIS)

The present invention provides a fuel cladding tube having an excellent corrosion resistance and thus a long life, and a suitable manufacturing method therefor. Namely, in the fuel cladding tube, the outer circumference of an inner layer made of a zirconium base alloy is coated with an outer layer made of a metal more corrosion resistant than the zirconium base alloy. Ti or a titanium alloy is suitable for the corrosion resistant metal. In addition, the outer layer can be coated by a method such as vapor deposition or plating, not limited to joining of the inner layer material and the outer layer material. Specifically, a composite material having an inner layer made of a zirconium alloy coated by the outer material made of a titanium alloy is applied with hot fabrication at a temperature within a range of from 500 to 850degC and at a fabrication rate of not less than 5%. The ...

International Nuclear Information System (INIS)

Available data are presented which support the supposition that metals and alloys with a negative low-temperature Hall coefficient are apparently not superconducting. (author).

Energy Technology Data Exchange (ETDEWEB)

The possibility of rapid heat treatment (RHT) application to titanium castings has been studied. It was shown that such treatment provides a significant improvement of intragrain structure and mechanical properties of cast ({alpha}+{beta})-titanium alloys. ((orig.))

Energy Technology Data Exchange (ETDEWEB)

A process for the generation of halogens from halide-containing solutions includes the step of conducting electrolysis of the solutions in an electrolytic cell having a platinum based amorphous metal alloy anode.

Energy Technology Data Exchange (ETDEWEB)

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride <0.05 M containing 30% ethylene glycol solution, they are more corrosive than the blank (30% ethylene glycol-70% water). However, at concentrations <0.05 for chloride or >0.05 M for fluoride containing ethylene ...

International Nuclear Information System (INIS)

The status of development and commercialization of a modified 9 Cr-1 Mo alloy is presented. The alloy is modified by the addition of 0.06 to 0.10% Nb and 0.18 to 0.25% V. The alloy is recommended for use in the normalized and tempered condition (1040"0C for 1 h, air cooled to room temperature; 760"0C for 1 h, air cooled to room temperature). Heat treatment, Charpy impact, tensile, and creep properties of the alloy are described in detail along with a brief description of other properties. The modified alloy has creep strength that exceeds that of standard 9 Cr-1 Mo and 2 1/4 Cr-1 Mo steels for the temperature range from 427 to 704"0C. The total-elongation and reduction-of-area values for all test temperatures and rupture times up to 22,500 h exceed 15 and 70%, respectively. The estimated design allowable stresses for this alloy are higher than those for standard ...

Science.gov (United States)

Quantitative metallography is often used to confirm the proper processing of aerospace metallic materials. A microstructural feature of great importance for titanium alloys processed in the alpha-beta phase field is the volume fraction of primary alpha. S...

Energy Technology Data Exchange (ETDEWEB)

The carbon transfer has been analyzed in the Alloy 800/sodium/stainless steel system by determining the carbon-uptake of Alloy 800 foils, which were exposed in liquid sodium of known carburizing potential. Under equilibrium conditions between 650 and 550/sup 0/C the measured total carbon concentrations in the Alloy 800 tabs were found to be roughly related to the carbon activities of the sodium environment by the equation already stated for the 18 Cr-8/10 Ni stainless steels, extrapolated to the chemical composition of the Ni-rich austenitic alloy. However the Alloy 800 was not found to undergo any decarburization in low-carbon activity environments. The carbon diffusion kinetics was determined as a function of temperature, it was found to be similar to that reported for the AISI-304 type of steel. The effects of sodium exposure on microstructural and mechanical properties of ...

Science.gov (United States)

The authors have presented results of an investigation of wettability of SiC particulates by liquid alloys of the Al-Si-Mg system. The evaluation of wetting has been carried out through the determination of the threshold pressure for infiltration of packed SiC particulates by the liquid alloy. The results indicate that whereas Si and Mg additions do not affect wetting, in the case of the ternary alloys the contact angle decreases in an amount proportional to the content of Mg[sub 2]Si.

International Nuclear Information System (INIS)

A series of ball-on-disc wear and friction measurements were made for surfaces which have a chemical vapour deposition carbon silicon alloy layer on a carbon substrate (fine grain POCO graphite). Nitrogen ion irradiation was used to improve the wear resistance of the carbon alloy surface. For comparison, measurements were also taken for alumina against alumina. It was found that the lowest friction coefficient and lowest wear occurred for ion irradiated coated samples containing 4% Si in the alloy and that the performance was superior to that of alumina. ((orig.)).

Energy Technology Data Exchange (ETDEWEB)

The exposure of heat-resistant alloys to high temperature can significantly change their mechanical properties. This paper presents and analyzes data on the effect of thermal exposure on the tensile and impact behavior of three cast materials -- the HK-40, HP-50, and 21Cr-32Ni-Fe alloys -- and of wrought material -- Alloy 800. The changes in tensile and impact properties caused by high-temperature exposure are reviewed. Reasons for these property changes and needs for considering them in the design, operation, and life assessment of high-temperature equipment are discussed.

Energy Technology Data Exchange (ETDEWEB)

The chemical properties of alloys in a given environment are to a large extent governed by the surface composition. Changes of the surface composition during passivation are important features in this respect. Previous studies of single crystal Ni-Mo alloys surfaces have been reported. The aim of this work was to obtain quantitative data, for the natural oxide and the passive films formed on Ni-6% Mo(100) and (110) alloys, using Rutherford backscattering spectroscopy and nuclear reaction analysis.

International Nuclear Information System (INIS)

Phase transformations occuring during cold deformation in hardened #alpha#+#beta# titanium alloy of the Ti-Al-Mo-Zr-Sn-Si system with 10% summary content of alloying elements are studied by X-ray diffraction analysis. Two stages of trapsformation of metastable #alpha#''-phase are found. A conclusiop is made that ability of the alloy containing #alpha#''-phase to cold deformation is determined by the presence of favourable texture, by high degree of metastability and by volume portion of #alpha#''-phase in the alloy structure.

International Nuclear Information System (INIS)

A computerized corrosion measuring system (EG and G model 350 A) was used to study the influence of Cr, Mo, Ti, Nb and W on the pitting corrosion of nickel base alloys in 3% NaCl at 90"0C. The electrochemical parameters under investigation are the corrosion potential E_c_o_r_r, pitting potential E_p and protection potential E_p_p. The corrosion behaviour of nickel base alloys were studied by using pitting scan and potentiostatic techniques. Values of corrosion potential, pitting potential and protection potential were used for a ranking of alloys for corrosion resistance.

International Nuclear Information System (INIS)

Formation of the soft magnetic nanostructure in amorphous Fe_1_4Ni_4_0Zr_7B_1_2 alloy due to heat treatment is studied by the Moessbauer, differential scanning calorimetry, and X-ray diffraction techniques. Annealing at temperatures 520-580 "oC leads to the formation of extremely soft nanocrystalline alloy as revealed by the rf-Moessbauer measurements. The superparamagnetic behaviour was observed for the alloy annealed at 620-640 "oC. At higher annealing temperatures good soft magnetic properties deteriorate. (author)

Energy Technology Data Exchange (ETDEWEB)

Experiments were conducted which established that the higher passivating capacity of Ni/sub 60/Nb/sub 40/ alloys in the amorphous state and higher efficiency of the anodic process of generation of chlorine (2 N NaCl + HCl to pH = 0) in comparison with the crystalline state are determined by higher homogeneity and density of the passive films formed on the amorphous alloy and by higher electron conduction which depends directly on the difference in the structure of the passive films formed on the alloys in the amorphous and crystalline states.

International Nuclear Information System (INIS)

The methods of optical and transmission electron microscopy were used to study the influence of different programmes of hot deformation on the structure formation of (#alpha#+#beta#) titanium alloy VT9. The #beta# alloy VT-15 was studied at the same time in order to simulate the dislocation structure generated in the process of hot deformation. During the hot deformation of two-phase titanium alloys in both #beta# and (#alpha#+#beta#) ranges there is found to be an optimum range of deformation in which a homogeneous, polygonized structure is formed.

International Nuclear Information System (INIS)

We propose a dissolution-passivation model to account for the electrochemical behavior of Alloy 800 and 316L stainless steel under steam generators operating conditions. This model is similar to the one defined for nickel, considering the known importance of this element on the studied alloys. The comparison of the rates of the elementary steps points out the favorable influence of dissolved oxygen and phosphate ions on the dissolution of Alloy 800, even in the presence of chloride ions. The sensitivity of 316L SS is greater, especially because of the lowest stability of oxide-like intermediate.

Energy Technology Data Exchange (ETDEWEB)

An experimental verification for long-term performance of a Pd-Ag permeation in ITER tritium fusion cleanup units (FCU) is needed. In addition, information is required on the influence of tritium and {sup 3}He decay on the physical and chemical properties of Pd-Ag alloys (V-1). The results of the investigations of alloys (V-1) (mechanical properties and microstructure) after long-term usage exposition in tritium are given in this report. The experimental conditions (temperature, pressure, clearance, {sup 3}He concentrations) and the previous conclusions on the V-1 alloy performance are presented. (orig.).

International Nuclear Information System (INIS)

Formation of basis type texture at rolling of Ti + 6.0% Al + 1.5% V + 1.0% Mo system alloy with initial prismatic texture is investigated by means of X-ray techniques. Variations of mechanical features in titanium alloy sheets depending on temperature-deformation conditions of rolling are investigated. Main conditions for formation of the intensive basis textute in the investigated alloy sheets which provides for isotropic properties in sheet plane and for increased ductility are determined.