Dosimetry work and calculations in connection with the irradiation of large devices in the high flux materials testing reactor BR2

International Nuclear Information System (INIS)

De Raedt, C.; Leenders, L.; Tourwe, H.; Farrar, H. IV.

1982-01-01

For about fifteen years the high flux reactor BR2 has been involved in the testing of fast reactor fuel pins. In order to simulate the fast reactor neutron environment most devices are irradiated under cadmium screen, cutting off the thermal flux component. Extensive neutronic calculations are performed to help the optimization of the fuel bundle design. The actual experiments are preceded by irradiations of their mock-ups in BR02, the zero power model of BR2. The mock-up irradiations, supported by supplementary calculations, are performed for the determination of the main neutronic characteristics of the irradiation proper in BR2 and for the determination of the corresponding operation data. At the end of the BR2 irradiation, the experimental results, such as burn-ups, neutron fluences, helium production in the fuel pin claddings, etc. are correlated by neutronic calculations in order to examine the consistency of the post-irradiation results and to validate the routine calculation procedure and cross-section data employed. A comparison is made in this paper between neutronic calculation results and some post-irradiation data for MOL 7D, a cadmium screened sodium cooled loop containing a nineteen fuel pin bundle

Application of MCNPX 2.7.D for reactor core management at the research reactor BR2

International Nuclear Information System (INIS)

Kalcheva, Silva; Koonen, Edgar

2011-01-01

The paper discusses application of the Monte Carlo burn up code MCNPX 2.7.D for whole core criticality and depletion analysis of the Material Testing Research Reactor BR2 at SCK-CEN in Mol, Belgium. Two different approaches in the use of MCNPX 2.7.D are presented. The first methodology couples the evolution of fuel depletion, evaluated by MCNPX 2.7.D in an infinite lattice with a steady-state 3-D power distribution in the full core model. The second method represents fully automatic whole core depletion and criticality calculations in the detailed 3-D heterogeneous geometry model of the BR2 reactor. The accuracy of the method and computational time as function of the number of used unique burn up materials in the model are being studied. The depletion capabilities of MCNPX 2.7.D are compared vs. the developed at the BR2 reactor department MCNPX & ORIGEN-S combined method. Testing of MCNPX 2.7.D on the criticality measurements at the BR2 reactor is presented. (author)

BR2 reactor: medical and industrial applications

International Nuclear Information System (INIS)

Ponsard, B.

2005-01-01

The radioisotopes are produced for various applications in the nuclear medicine (diagnostic, therapy, palliation of metastatic bone pain), industry (radiography of welds, ...), agriculture (radiotracers, ...) and basic research. Due to the availability of high neutron fluxes (thermal neutron flux up to 10 15 n/cm 2 .s), the BR2 reactor is considered as a major facility through its contribution for a continuous supply of products such 99 Mo ( 99 mTc), 131 I, 133 Xe, 192 Ir, 186 Re, 153 Sm, 90 Y, 32 P, 188 W ( 188 Re), 203 Hg, 82 Br, 41 Ar, 125 I, 177 Lu, 89 Sr, 60 Co, 169 Yb, 147 Nd, and others. Neutron Transmutation Doped (NTD) silicon is produced for the semiconductor industry in the SIDONIE (Silicon Doping by Neutron Irradiation Experiment) facility, which is designed to continuously rotate and traverse the silicon through the neutron flux. These combined movements produce exceptional dopant homogeneity in batches of silicon measuring 4 and 5-inches in diameter by up to 750 mm in length. The main objectives of work performed were to provide a reliable and qualitative supply of radioisotopes and NTD-silicon to the customers in accordance with a quality system that has been certified to the requirements of the EN ISO 9001: 2000. This new Quality System Certificate has been obtained in November 2003 for the Production of radioisotopes for medical and industrial applications and the Production of Neutron Transmutation Doped (NTD) Silicon in the BR2 reactor

Production of Sn-117m in the BR2 high-flux reactor.

Science.gov (United States)

Ponsard, B; Srivastava, S C; Mausner, L F; Russ Knapp, F F; Garland, M A; Mirzadeh, S

2009-01-01

The BR2 reactor is a 100MW(th) high-flux 'materials testing reactor', which produces a wide range of radioisotopes for various applications in nuclear medicine and industry. Tin-117m ((117m)Sn), a promising radionuclide for therapeutic applications, and its production have been validated in the BR2 reactor. In contrast to therapeutic beta emitters, (117m)Sn decays via isomeric transition with the emission of monoenergetic conversion electrons which are effective for metastatic bone pain palliation and radiosynovectomy with lesser damage to the bone marrow and the healthy tissues. Furthermore, the emitted gamma photons are ideal for imaging and dosimetry.

Loss-of-Flow and Loss-of-Pressure Simulations of the BR2 Research Reactor with HEU and LEU Fuel

Energy Technology Data Exchange (ETDEWEB)

Licht, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Bergeron, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-01-01

Belgian Reactor 2 (BR2) is a research and test reactor located in Mol, Belgium and is primarily used for radioisotope production and materials testing. The Materials Management and Minimization (M3) Reactor Conversion Program of the National Nuclear Security Administration (NNSA) is supporting the conversion of the BR2 reactor from Highly Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. The reactor core of BR2 is located inside a pressure vessel that contains 79 channels in a hyperboloid configuration. The core configuration is highly variable as each channel can contain a fuel assembly, a control or regulating rod, an experimental device, or a beryllium or aluminum plug. Because of this variability, a representative core configuration, based on current reactor use, has been defined for the fuel conversion analyses. The code RELAP5/Mod 3.3 was used to perform the transient thermal-hydraulic safety analyses of the BR2 reactor to support reactor conversion. The input model has been modernized relative to that historically used at BR2 taking into account the best modeling practices developed by Argonne National Laboratory (ANL) and BR2 engineers.

In-pile creep test technique for zirconium alloys examination in BR-10 reactor channels

International Nuclear Information System (INIS)

Pevchikh, Yu.M.; Kruglov, A.S.; Troyanov, V.M.

2002-01-01

The irradiation enhanced creep phenomenon was discovered in stainless steels as a specific physical process accompanying high-intensity neutron flux irradiation in fast reactors. IPPE is also experienced in irradiation creep test activities, studying different types of materials under irradiation in BR-10 fast reactor. Series of in-channel type test facilities were constructed and tested in BR-10 reactor's 'dry' channels in order to carry out full-scale instrumented examination regarded to in-pile creep behaviour of different reactor materials. As a result, a specific test technique, named 'Tensometric method', has been developed and experimentally proved to be power enough in order to investigate irradiation creep of materials right in situ under neutron irradiation. The main peculiarity of test facility, which is constructed to apply the tensometric method, consists in absence of any special deformation-measurement cell at all. The in-pile creep strain measurement technique developed at IPPE is based on the non-direct measurement of specimen's deformation (either linear tensile strain or angular twisting one), which directly affects the loaded draws' tension parameters. Starting from 1993, in-pile creep experiments to investigate in-reactor creep behaviour of E110 and E635 zirconium alloys were carried out in BR-10. Experimental results and data collected during more than 20-year of BR-10 in-reactor creep test experience can be assumed as a strong evidence that the tensometric technique is a powerful instrument, which can give a chance to study different irradiation effects on reactor materials directly under irradiation. (author)

Recent advances in the utilization and the irradiation technology of the refurbished BR2 reactor

International Nuclear Information System (INIS)

Dekeyser, J.; Benoit, P.; Decloedt, C.; Pouleur, Y.; Verwimp, A.; Weber, M.; Vankeerberghen, M.; Ponsard, B.

1999-01-01

Operation and utilization of the materials testing reactor BR2 at the Belgian Nuclear Research Centre (SCK·CEN) has since its start in 1963 always followed closely the needs and developments of nuclear technology. In particular, a multitude of irradiation experiments have been carried out for most types of nuclear power reactors, existing or under design. Since the early 1990s and increased focus was directed towards more specific irradiation testing needs for light water reactor fuels and materials, although other areas of utilization continued as well (e.g. fusion reactor materials, safety research, ...), including also the growing activities of radioisotope production and silicon doping. An important milestone was the decision in 1994 to implement a comprehensive refurbishment programme for the BR2 reactor and plant installations. The scope of this programme comprised very substantial studies and hardware interventions, which have been completed in early 1997 within planning and budget. Directly connected to this strategic decision for reactor refurbishment was the reinforcement of our efforts to requalify and upgrade the existing irradiation facilities and to develop advanced devices in BR2 to support emerging programs in the following fields: - LWR pressure vessel steel, - LWR irradiation assisted stress corrosion cracking (IASCC), - reliability and safety of high-burnup LWR fuel, - fusion reactor materials and blanket components, - fast neutron reactor fuels and actinide burning, - extension and diversification of radioisotope production. The paper highlights these advances in the areas of BR2 utilisation and the ongoing development activities for the required new generation of irradiations devices. (author)

Pathways for the OH + Br2 → HOBr + Br and HOBr + Br → HBr + BrO Reactions.

Science.gov (United States)

Wang, Hongyan; Qiu, Yudong; Schaefer, Henry F

2016-02-11

The OH radical reaction with Br2 and the subsequent reaction HOBr + Br are of exceptional importance to atmospheric chemistry and environmental chemistry. The entrance complex, transition state, and exit complex for both reactions have been determined using the coupled-cluster method with single, double, and perturbative triple excitations CCSD(T) with correlation consistent basis sets up to size cc-pV5Z and cc-pV5Z-PP. Coupled cluster effects with full triples (CCSDT) and full quadruples (CCSDTQ) are explicitly investigated. Scalar relativistic effects, spin-orbit coupling, and zero-point vibrational energy corrections are evaluated. The results from the all-electron basis sets are compared with those from the effective core potential (ECP) pseudopotential (PP) basis sets. The results are consistent. The OH + Br2 reaction is predicted to be exothermic 4.1 ± 0.5 kcal/mol, compared to experiment, 3.9 ± 0.2 kcal/mol. The entrance complex HO···BrBr is bound by 2.2 ± 0.2 kcal/mol. The transition state lies similarly well below the reactants OH + Br2. The exit complex HOBr···Br is bound by 2.7 ± 0.6 kcal/mol relative to separated HOBr + Br. The endothermicity of the reaction HOBr + Br → HBr + BrO is 9.6 ± 0.7 kcal/mol, compared with experiment 8.7 ± 0.3 kcal/mol. For the more important reverse (exothermic) HBr + BrO reaction, the entrance complex BrO···HBr is bound by 1.8 ± 0.6 kcal/mol. The barrier for the HBr + BrO reaction is 6.8 ± 0.9 kcal/mol. The exit complex (Br···HOBr) for the HBr + BrO reaction is bound by 1.9 ± 0.2 kcal/mol with respect to the products HOBr + Br.

Decommissioning of the BR3 pressurized-water reactor

International Nuclear Information System (INIS)

Massaut, V.

1996-01-01

The dismantling and the decommissioning of nuclear installations at the end of their life-cycle is a new challenge to the nuclear industry. Different techniques and procedures for the dismantling of a nuclear power plant on an existing installation, the BR-3 pressurized-water reactor, are described. The scientific programme, objectives, achievements in this research area at the Belgian Nuclear Research Centre SCK-CEN for 1995 are summarized

Spent fuel strategy for the BR2 reactor

International Nuclear Information System (INIS)

Gubel, P.; Collard, G.

1998-01-01

The Belgian MTR reactor is fuelled with HEU UAl x elements and the fuel cycle was normally closed by reprocessing consecutively in Belgium (Eurochemic), France (Marcoule) and finally in the U.S.A. (Idaho Falls and Savannah River). When the acceptance of spent fuel by the U.S. was terminated, the facility was left with a huge backlog of used elements stored under water. After a few years, urgent and mandatory actions were required to maintain the BR2 facility operating. Later the accent was put on the evaluation of an optimum long term solution for the BR2 spent fuel during the projected 15 years life extension after the refurbishment executed between 1995 and 1997. The paper gives an overview of these successive actions taken during the last years as well as the handled various criteria for comparing and evaluating the available long-term alternatives. After commitment to reprocessing in existing facilities operated for aluminum fuels the focus of the BR2 fuel cycle strategy is now moving to the procurement of the necessary HEU fuel for securing the long-term operation of the facility. (author)

Validation of SCALE4.4a for Calculation of Xe-Sm Transients After a Scram of the BR2 Reactor

International Nuclear Information System (INIS)

Kalcheva, S.; Ponsard, B.; Koonen, E.

2007-01-01

The aim of this report is to validate the computational modules system SCALE4.4a for evaluation of reactivity changes, macroscopic absorption cross sections and calculations of the positions of the Control Rods during their motion in Xe-Sm transient after a scram of the BR-2 reactor. The rapid shutting down of the reactor by inserting of negative reactivity by the Control Rods is known as a reactor scram. Following reactor scram, a large xenon and samarium buildup occur in the reactor, which may appreciably affect the multiplication factor of the core due to enormous neutron absorption. The validation of the calculations of Xe-Sm transients by SCALE4.4a has been performed on the measurements of the positions of the Control Rods during their motion in Xe-Sm transients of the BR-2 reactor and on comparison with the calculations by the standard procedure XESM, developed at the BR-2 reactor. A final conclusion is made that the SCALE4.4a modules system can be used for evaluation of Xe-Sm transients of the BR-2 reactor. The utilization of the code is simple, the computational time takes from few seconds.

General outline of the operation and utilization of the BR2 reactor

International Nuclear Information System (INIS)

Baugnet, J.M.; Leonard, F.; Gandolfo, J.M.; Lenders, H.

1978-01-01

The BR2 reactor is a high-flux material testing reactor of the thermal heterogeneous type. The fuel is 93% 235 U enriched uranium in the form of plates clad in aluminium. The moderator consists of beryllium and light water, the water being pressurized (12.5kg/cm 2 )and acting also as coolant. The pressure vessel is of aluminium, and is placed in a pool of demineralized water. One should stress the following main features of the design: the experimental channels are skew, the tube bundle presenting the form of a hyperboloid of revolution (see figure 1)-this gives easy access at the top and bottom reactor covers allowing complex instrumented devices, while maintaining a very high neutron flux at the core; great flexibilty of utilization, due to the fact that it is possible to adapt the core configuration to the experimental loading as the fissile charge can be centred on different experimental channels; although BR2 is a thermal reactor, it is possible to achieve neutron spectra very similar to those obtained in a fast reactor, either by the use of absorbing screens or by the use of fissile material within the experimental device; five 200mm diameter channels are available for loading large experimental irradiation devices, as in-pile sodium, gas or water loops. (author)

Annealing of the BR3 reactor pressure vessel

International Nuclear Information System (INIS)

Fabry, A.; Motte, F.; Stiennon, G.; Debrue, J.; Gubel, P.; Van de Velde, J.; Minsart, G.; Van Asbroeck, P.

1985-01-01

The pressure vessel of the Belgian BR-3 plant, a small (11 MWe) PWR presently used for fuel testing programs and operated since 1962, was annealed during March, 1984. The anneal was performed under wet conditions for 168 hours at 650 0 F with core removal and within plant design margins justification for the anneal, summary of plant characteristics, description of materials sampling, summary of reactor physics and dosimetry, development of embrittlement trend curves, hypothesized pressurized and overcooling thermal shock accidents, and conclusions are provided in detail

Mixed core management: Use of 93% and 72% enriched uranium in the BR2 reactor

International Nuclear Information System (INIS)

Ponsard, B.

2000-01-01

The BR2 reactor, put into operation in 1963 and refurbished from July 1995 till April 1997, is a 100 MW high-flux Materials Testing Reactor, using 93% 235 U enriched uranium as standard fuel, light water as coolant and beryllium as moderator. The present operating regime consists of five irradiation cycles per year at an operating power between 50 and 70 MW; each cycle is characterized by 21 days operation. In the framework of a 'qualification programme', six 72% 235 U fuel elements fabricated with uranium recovered from the reprocessing of BR2 spent fuel at UKAEA-Dounreay have been successfully irradiated in the period 1994-1995 reaching a maximum mean burnup of 48% without the release of fission products. Since 1998, this type of fuel element is irradiated routinely together with standard 93% 235 U fuel elements in order to optimize the utilization of the available HEU inventory. The purpose of this paper is to present the strategy developed in order to optimize the mixed core management of the BR2 reactor. (author)

Steady-State Thermal-Hydraulics Analyses for the Conversion of the BR2 Reactor to LEU

Energy Technology Data Exchange (ETDEWEB)

Licht, J. R. [Argonne National Lab. (ANL), Argonne, IL (United States); Bergeron, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Van den Branden, G. [SCK CEN (Belgium); Kalcheva, S. [SCK CEN (Belgium); Sikik, E. [SCK CEN (Belgium); Koonen, E. [SCK CEN (Belgium)

2015-12-01

BR2 is a research reactor used for radioisotope production and materials testing. It’s a tank-in-pool type reactor cooled by light water and moderated by beryllium and light water (Figure 1). The reactor core consists of a beryllium moderator forming a matrix of 79 hexagonal prisms in a hyperboloid configuration; each having a central bore that can contain a variety of different components such as a fuel assembly, a control or regulating rod, an experimental device, or a beryllium or aluminum plug. Based on a series of tests, the BR2 operation is currently limited to a maximum allowable heat flux of 470 W/cm2 to ensure fuel plate integrity during steady-state operation and after a loss-of-flow/loss-of-pressure accident.

The BR2 materials testing reactor. Past, ongoing and under-study upgradings

Energy Technology Data Exchange (ETDEWEB)

Baugnet, J M; Roedt, Ch de; Gubel, P; Koonen, E [Centre d' Etude de I' Energie Nucleaire, Studiecentrum voor Kernenergie, C.E.N./S.C.K., Mol (Belgium)

1990-05-01

The BR2 reactor (Mol, Belgium) is a high-flux materials testing reactor. The fuel is 93% {sup 235}U enriched uranium. The nominal power ranges from 60 to 100 MW. The main features of the design are the following: 1) maximum neutron flux, thermal: 1.2 x 10{sup 15} n/cm{sup 2} s; fast (E > 0.1 MeV) : 8.4 x 10{sup 14} n /cm{sup 2} s; 2) great flexibility of utilization: the core configuration and operation mode can be adapted to the experimental loading; 3) neutron spectrum tailoring; 4) availability of five 200 mm diameter channels besides the standard channels (84 mm diameter); 5) access to the top and bottom covers of the reactor authorizing the irradiation of loops. The reactor is used to study the behaviour of fuel elements and structural materials intended for future nuclear power stations of several types (fission and fusion). Irradiations are carried out in connection with performance tests up to very high burn-up or neutron fluence as well as for safety experiments, power cycling experiments, and generally speaking, tests under off-normal conditions. Irradiations for nuclear transmutation (production of high specific activity radio-isotopes and transplutonium elements), neutron-radiography, use of beam tubes for physics studies, and gamma irradiations are also carried out. The BR2 is used in support of Belgian programs, at the request of utilities, industry and universities and in the framework of international agreements. The paper reviews the past and ongoing upgrading and enhancement of reactor capabilities as well as those under study or consideration, namely with regard to: reactor equipment, fuel elements, irradiation facilities, reactor operation conditions and long-term strategy. (author)

SoLid: Search for Oscillations with Lithium-6 Detector at the SCK-CEN BR2 reactor

Science.gov (United States)

Ban, G.; Beaumont, W.; Buhour, J. M.; Coupé, B.; Cucoanes, A. S.; D'Hondt, J.; Durand, D.; Fallot, M.; Fresneau, S.; Giot, L.; Guillon, B.; Guilloux, G.; Janssen, X.; Kalcheva, S.; Koonen, E.; Labare, M.; Moortgat, C.; Pronost, G.; Raes, L.; Ryckbosch, D.; Ryder, N.; Shitov, Y.; Vacheret, A.; Van Mulders, P.; Van Remortel, N.; Weber, A.; Yermia, F.

2016-04-01

Sterile neutrinos have been considered as a possible explanation for the recent reactor and Gallium anomalies arising from reanalysis of reactor flux and calibration data of previous neutrino experiments. A way to test this hypothesis is to look for distortions of the anti-neutrino energy caused by oscillation from active to sterile neutrino at close stand-off (˜ 6- 8m) of a compact reactor core. Due to the low rate of anti-neutrino interactions the main challenge in such measurement is to control the high level of gamma rays and neutron background. The SoLid experiment is a proposal to search for active-to-sterile anti-neutrino oscillation at very short baseline of the SCK•CEN BR2 research reactor. This experiment uses a novel approach to detect anti-neutrino with a highly segmented detector based on Lithium-6. With the combination of high granularity, high neutron-gamma discrimination using 6LiF:ZnS(Ag) and precise localization of the Inverse Beta Decay products, a better experimental sensitivity can be achieved compared to other state-of-the-art technology. This compact system requires minimum passive shielding allowing for very close stand off to the reactor. The experimental set up of the SoLid experiment and the BR2 reactor will be presented. The new principle of neutrino detection and the detector design with expected performance will be described. The expected sensitivity to new oscillations of the SoLid detector as well as the first measurements made with the 8 kg prototype detector deployed at the BR2 reactor in 2013-2014 will be reported.

Steady-State Thermal-Hydraulics Analyses for the Conversion of the BR2 Reactor to LEU

Energy Technology Data Exchange (ETDEWEB)

Licht, J. R. [Argonne National Lab. (ANL), Argonne, IL (United States); Bergeron, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Kalcheva, S [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Sikik, E [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-09-01

BR2 is a research reactor used for radioisotope production and materials testing. It’s a tank-in-pool type reactor cooled by light water and moderated by beryllium and light water. The reactor core consists of a beryllium moderator forming a matrix of 79 hexagonal prisms in a hyperboloid configuration; each having a central bore that can contain a variety of different components such as a fuel assembly, a control or regulating rod, an experimental device, or a beryllium or aluminum plug. Based on a series of tests, the BR2 operation is currently limited to a maximum allowable heat flux of 470 W/cm² to ensure fuel plate integrity during steady-state operation and after a loss-of-flow/loss-of-pressure accident. A feasibility study for the conversion of the BR2 reactor from highly-enriched uranium (HEU) to low-enriched uranium (LEU) fuel was previously performed to verify it can operate safely at the same maximum nominal steady-state heat flux. An assessment was also performed to quantify the heat fluxes at which the onset of flow instability and critical heat flux occur for each fuel type. This document updates and expands these results for the current representative core configuration (assuming a fresh beryllium matrix) by evaluating the onset of nucleate boiling (ONB), onset of fully developed nucleate boiling (FDNB), onset of flow instability (OFI) and critical heat flux (CHF).

Monte Carlo modelling of the Belgian materials testing reactor BR2: present status

International Nuclear Information System (INIS)

Verboomen, B.; Aoust, Th.; Raedt, Ch. de; Beeckmans de West-Meerbeeck, A.

2001-01-01

A very detailed 3-D MCNP-4B model of the BR2 reactor was developed to perform all neutron and gamma calculations needed for the design of new experimental irradiation rigs. The Monte Carlo model of BR2 includes the nearly exact geometrical representation of fuel elements (now with their axially varying burn-up), of partially inserted control and regulating rods, of experimental devices and of radioisotope production rigs. The multiple level-geometry possibilities of MCNP-4B are fully exploited to obtain sufficiently flexible tools to cope with the very changing core loading. (orig.)

Aagesta-BR3 Decommissioning Cost. Comparison and Benchmarking Analysis

Energy Technology Data Exchange (ETDEWEB)

Varley, Geoff [NAC International, Henley on Thames (United Kingdom)

2002-11-01

This report presents the results of decommissioning cost analyses focusing on discrete working packages within the decommissioning program of the BR3 reactor in Mol, Belgium and comparison of them with cost estimate data for the Aagesta research reactor in Sweden. The specific BR3 work packages analysed were: Primary coolant piping decontamination; Primary coolant piping dismantling; Vulcain reactor internals dismantling; Westinghouse reactor internals dismantling; Reactor vessel dismantling. The main conclusions to be drawn from the analyses are that: The fixed costs related to decontamination and dismantling activities generally are a very important part of the overall resources needed to execute the work, with the Reactor Pressure Vessel (RPV) seemingly being significantly more demanding than other major components. Cutting activities tend to need something like 150 to 200 labour hours per m{sup 2} of reactor equipment dismantled. Fixed investment costs to set up the equipment needed to cut up major vessels or internals appear to be in the range of MSEK 4 to 8. Consumables costs vary according to the nature of the equipment being dismantled. The thicker the metal being cut, the higher the attrition rate for things such as cutting blades. The range of consumables costs at BR3 have been in the range of MSEK 0.1 to 0.2/m{sup 2} dismantled. The extent of detailed information available in the 1996 Aagesta estimate is not sufficient to enable a full comparison with the BR3 decommissioning results. A global first comparison has been attempted by summing the resources expended on the BR3 work packages described in this report with the combined dismantling data presented in the 1996 Aagesta cost estimate report. Very broadly the cost of decontamination plus dismantling of the main process equipment at Aagesta appears to be in the order of MSEK 70, of which MSEK 4 is labour on preparatory/planning work, MSEK 40 is labour on actual decontamination and dismantling and MSEK

Boiling water reactor modeling capabilities of MMS-02

International Nuclear Information System (INIS)

May, R.S.; Abdollahian, D.A.; Elias, E.; Shak, D.P.

1987-01-01

During the development period for the Modular Modeling System (MMS) library modules, the Boiling Water Reactor (BWR) has been the last major component to be addressed. The BWRX module includes models of the reactor core, reactor vessel, and recirculation loop. A pre-release version was made available for utility use in September 1983. Since that time a number of changes have been incorporated in BWRX to (1) improve running time for most transient events of interest, (2) extend its capability to include certain events of interest in reactor safety analysis, and (3) incorporate a variety of improvements to the module interfaces and user input formats. The purposes of this study were to briefly review the module structure and physical models, to point the differences between the MMS-02 BWRX module and the BWRX version previously available in the TESTREV1 library, to provide guidelines for choosing among the various user options, and to present some representative results

The experience of the fuel waste management of AM and BR-10 reactor facilities at SSC RF IPPE named after A.I. Leipunsky

International Nuclear Information System (INIS)

Kochetkov, L.A.; Mamaev, L.I.; Stuzhnev, Yu.A.

1999-01-01

8 research and experimental reactors have been created at the Institute industrial site. The majority of them have been or are being decommissioned now. During many decades the reactor of the first-in-the-world NPP -AM and the fast neutron reactor BR-5 (BR-10) are the main research reactor bases of the Institute. They have been in operation for 45 and 40 years respectively. At present the preparation work for their decommissioning is being carried out. One of the problems of that process is the fuel waste management which amount is about 13 tons. The possibility of its reprocessing is under consideration. (author)

Aagesta-BR3 Decommissioning Cost. Comparison and Benchmarking Analysis

International Nuclear Information System (INIS)

Varley, Geoff

2002-11-01

This report presents the results of decommissioning cost analyses focusing on discrete working packages within the decommissioning program of the BR3 reactor in Mol, Belgium and comparison of them with cost estimate data for the Aagesta research reactor in Sweden. The specific BR3 work packages analysed were: Primary coolant piping decontamination; Primary coolant piping dismantling; Vulcain reactor internals dismantling; Westinghouse reactor internals dismantling; Reactor vessel dismantling. The main conclusions to be drawn from the analyses are that: The fixed costs related to decontamination and dismantling activities generally are a very important part of the overall resources needed to execute the work, with the Reactor Pressure Vessel (RPV) seemingly being significantly more demanding than other major components. Cutting activities tend to need something like 150 to 200 labour hours per m 2 of reactor equipment dismantled. Fixed investment costs to set up the equipment needed to cut up major vessels or internals appear to be in the range of MSEK 4 to 8. Consumables costs vary according to the nature of the equipment being dismantled. The thicker the metal being cut, the higher the attrition rate for things such as cutting blades. The range of consumables costs at BR3 have been in the range of MSEK 0.1 to 0.2/m 2 dismantled. The extent of detailed information available in the 1996 Aagesta estimate is not sufficient to enable a full comparison with the BR3 decommissioning results. A global first comparison has been attempted by summing the resources expended on the BR3 work packages described in this report with the combined dismantling data presented in the 1996 Aagesta cost estimate report. Very broadly the cost of decontamination plus dismantling of the main process equipment at Aagesta appears to be in the order of MSEK 70, of which MSEK 4 is labour on preparatory/planning work, MSEK 40 is labour on actual decontamination and dismantling and MSEK 25 is

Ongoing refurbishment activities and strategy for the future operation of the BR2 reactor

International Nuclear Information System (INIS)

Koonen, E.; Gubel, P.

1994-01-01

The operation of the BR2 reactor with its second Be-matrix is foreseen up to mid-1995 or mid-1996. A life extension for another 15 years is envisaged considering programmatic, financial and technical aspects. At present, the second phase of the refurbishment programme is being executed. The major activities of this programme can be grouped under two headings: safety reassessment and ageing issues. The expected outcome end '93 is an assessment report defining extent, choosen options, prioritized activities, budget and a tentative planning for the preparation and execution of the refurbishment. These aspects together with the prospects of possible cooperation with other parties for the refurbishment programme and the future operation of BR2 will be evaluated by the CEN/SCK Board who has to take a decision early in 1994. Various scenarios are now being considered and evaluated for the refurbishment and the future BR2 operation regime. (author)

Ongoing refurbishment activities and strategy for the future operation of the BR2 reactor

Energy Technology Data Exchange (ETDEWEB)

Koonen, E; Gubel, P [BR2 Department, Belgian Nuclear Research Center, CEN/SCK, Mol (Belgium)

1993-07-01

The operation of the BR2 reactor with its second Be-matrix is foreseen up to mid-1995 or mid-1996. A life extension for another 15 years is envisaged considering programmatic, financial and technical aspects. At present, the second phase of the refurbishment programme is being executed. The major activities of this programme can be grouped under two headings: safety reassessment and ageing issues. The expected outcome end '93 is an assessment report defining extent, choosen options, prioritized activities, budget and a tentative planning for the preparation and execution of the refurbishment. These aspects together with the prospects of possible cooperation with other parties for the refurbishment programme and the future operation of BR2 will be evaluated by the CEN/SCK Board who has to take a decision early in 1994. Various scenarios are now being considered and evaluated for the refurbishment and the future BR2 operation regime. (author)

Ongoing refurbishment activities and strategy for the future operation of the BR2 reactor

International Nuclear Information System (INIS)

Koonen, E.; Gubel, P.

1993-01-01

The operation of the BR2 reactor with its second Be-matrix is foreseen up to mid-1995 or mid-1996. A life extension for another 15 years is envisaged considering programmatic, financial and technical aspects. At present, the second phase of the refurbishment programme is being executed. The major activities of this programme can be grouped under two headings: safety reassessment and ageing issues. The expected outcome end '93 is an assessment report defining extent, choosen options, prioritized activities, budget and a tentative planning for the preparation and execution of the refurbishment. These aspects together with the prospects of possible cooperation with other parties for the refurbishment programme and the future operation of BR2 will be evaluated by the CEN/SCK Board who has to take a decision early in 1994. Various scenarios are now being considered and evaluated for the refurbishment and the future BR2 operation regime. (author)

Qualification of the on-line power determination of fuel elements in irradiation devices in the BR2 reactor

International Nuclear Information System (INIS)

Vermeeren, L.; Dekeyser, J.; Gouat, P.; Kalcheva, S.; Koonen, E.; Kuzminov, V.; Verwimp, A.; Weber, M.

2005-01-01

Fuel irradiation tests require an on-line monitoring of the fuel power. In the BR2 reactor, this is performed by continuously measuring the enthalpy change in the coolant of the irradiation device and complementing this information with data on power losses, heating of structure parts and spatial power profiles from mock-up test experiments and from calculations. Since a few years Monte Carlo codes (MCNP) are used, describing the BR2 core in great detail for every reactor cycle with its specific core load, yielding not only reliable relative values, but also calculated absolute local power values in agreement with data from PIE analyses. Several methods were conceived to combine the experimental and calculated data for the on-line calculation of the local linear power in the fuel elements; their internal consistency and the consistency with gamma spectroscopy data and data from radiochemical fission product analysis was checked. The data show that fuel irradiations in BR2 can be performed in a well-controlled way, with an accurate and reliable on-line follow-up of the fuel power. (author)

BR2 reactor core steady state transient modeling

International Nuclear Information System (INIS)

Makarenko, A.; Petrova, T.

2000-01-01

A coupled neutronics/hydraulics/heat-conduction model of the BR2 reactor core is under development at SCK-CEN. The neutron transport phenomenon has been implemented as steady state and time dependent nodal diffusion. The non-linear heat conduction equation in-side fuel elements is solved with a time dependent finite element method. To allow coupling between functional modules and to simulate subcooled regimes, a simple single-phase hydraulics has been introduced, while the two-phase hydraulics is under development. Multiple tests, general benchmark cases as well as calculation/experiment comparisons demonstrated a good accuracy of both neutronic and thermal hydraulic models, numerical reliability and full code portability. A refinement methodology has been developed and tested for better neutronic representation in hexagonal geometry. Much effort is still needed to complete the development of an extended cross section library with kinetic data and two-phase flow representation. (author)

Regulating the Emission Spectrum of CsPbBr3 from Green to Blue via Controlling the Temperature and Velocity of Microchannel Reactor

OpenAIRE

Yong Tang; Hanguang Lu; Longshi Rao; Zongtao Li; Xinrui Ding; Caiman Yan; Binhai Yu

2018-01-01

The ability to precisely obtain tunable spectrum of lead halide perovskite quantum dots (QDs) is very important for applications, such as in lighting and display. Herein, we report a microchannel reactor method for synthesis of CsPbBr3 QDs with tunable spectrum. By adjusting the temperature and velocity of the microchannel reactor, the emission peaks of CsPbBr3 QDs ranging from 520 nm to 430 nm were obtained, which is wider than that of QDs obtained in a traditional flask without changing hal...

arXiv Performance of a full scale prototype detector at the BR2 reactor for the SoLid experiment

CERN Document Server

Abreu, Y.; Arnold, L.; Ban, G.; Beaumont, W.; Bongrand, M.; Boursette, D.; Castle, B.C.; Clark, K.; Coupé, B.; Cussans, D.; De Roeck, A.; D'Hondt, J.; Durand, D.; Fallot, M.; Ghys, L.; Giot, L.; Guillon, B.; Ihantola, S.; Janssen, X.; Kalcheva, S.; Kalousis, L.N.; Koonen, E.; Labare, M.; Lehaut, G.; Manzanillas, L.; Mermans, J.; Michiels, I.; Moortgat, C.; Newbold, D.; Park, J.; Pestel, V.; Petridis, K.; Piñera, I.; Pommery, G.; Popescu, L.; Pronost, G.; Rademacker, J.; Ryckbosch, D.; Ryder, N.; Saunders, D.; Schune, M.-H.; Simard, L.; Vacheret, A.; Van Dyck, S.; Van Mulders, P.; van Remortel, N.; Vercaemer, S.; Verstraeten, M.; Weber, A.; Yermia, F.

2018-05-03

The SoLid collaboration has developed a new detector technology to detect electron anti-neutrinos at close proximity to the Belgian BR2 reactor at surface level. A 288 kg prototype detector was deployed in 2015 and collected data during the operational period of the reactor and during reactor shut-down. Dedicated calibration campaigns were also performed with gamma and neutron sources. This paper describes the construction of the prototype detector with a high control on its proton content and the stability of its operation over a period of several months after deployment at the BR2 reactor site. All detector cells provide sufficient light yields to achieve a target energy resolution of better than 20%/√E(MeV). The capability of the detector to track muons is exploited to equalize the light response of a large number of channels to a precision of 3% and to demonstrate the stability of the energy scale over time. Particle identification based on pulse-shape discrimination is demonstrated with calibration so...

Regulating the Emission Spectrum of CsPbBr3 from Green to Blue via Controlling the Temperature and Velocity of Microchannel Reactor

Science.gov (United States)

Tang, Yong; Lu, Hanguang; Rao, Longshi; Ding, Xinrui; Yan, Caiman; Yu, Binhai

2018-01-01

The ability to precisely obtain tunable spectrum of lead halide perovskite quantum dots (QDs) is very important for applications, such as in lighting and display. Herein, we report a microchannel reactor method for synthesis of CsPbBr3 QDs with tunable spectrum. By adjusting the temperature and velocity of the microchannel reactor, the emission peaks of CsPbBr3 QDs ranging from 520 nm to 430 nm were obtained, which is wider than that of QDs obtained in a traditional flask without changing halide component. The mechanism of photoluminescence (PL) spectral shift of CsPbBr3 QDs was investigated, the result shows that the supersaturation control enabled by the superior mass and heat transfer performance in the microchannel is the key to achieve the wide range of PL spectrum, with only a change in the setting of the temperature controller required. The wide spectrum of CsPbBr3 QDs can be applied to light-emitting diodes (LEDs), photoelectric sensors, lasers, etc. PMID:29498710

Monte Carlo simulation of irradiation of MTR fuel plates in the BR2 reactor using a full-scale 3-d model with inclined channels

International Nuclear Information System (INIS)

Kuzminov, V. V; Koonen, E.; Ponsard, B.

2002-01-01

A three-dimensional full-scale Monte Carlo model of the BR2 reactor has been developed for simulation of irradiation conditions of materials and fuel loaded in various irradiation devices. This new reactor model includes a detailed geometrical description of the inclined reactor channels, the irradiation devices loaded in these channels including the materials to be tested/loaded in these devices, the burn-up of the BR2 fuel elements and the poisoning of the beryllium matrix. Recently a benchmark irradiation of new irradiation device for testing and qualification of MTR fuel plates has been performed. For this purpose the detailed irradiation conditions of fuel plates had to be predetermined. Monte Carlo calculations of neutron fluxes and heat load distributions in irradiated MTR fuel plates were performed taking into account the contents of all loaded experimental devices in the reactor channels. A comparison of the calculated and measured values of neutron fluxes and of heat loads in the BR2 reactor is presented in this paper. The comparison is part of the validation process of the new reactor model. It also serves to establish the capability to conduct a fuel plate irradiation program under requested and well- known irradiation conditions. (author)

Qualification of high density aluminide fuels for the BR2 reactor

International Nuclear Information System (INIS)

Beeckmans de West-Meerbeeck, Andre; Gubel, Pol; Ponsard, Bernard; Pin, Thomas; Falgoux, Jean Louis

2005-01-01

The BR2 operation still relies on the use of 90..93% enriched HEU aluminide fuel. The availability of a limited batch of 73% enriched HEU from reprocessed BR2 uranium in Dounreay justified 10 years ago the qualification and use of this material. After some preliminary test irradiations, various batches of fuel elements were fabricated by the UKAEA-Dounreay and successfully irradiated. Due to their lower 235 U content (0.050 g 235 U/cm 2 ), these elements were always irradiated together with standard 90...93% HEU fuel elements. A mixed-core strategy was developed at this occasion for an optimal utilization, and was reported during the 4th RRFM conference (March 19-21, 2000, Colmar, France). The availability of a new batch of fresh 73% HEU material was the occasion, a few years ago, to initiate the development, fabrication and qualification of a new high density fuel element. An order was placed with CERCA to assess the optimal fabrication methods and tooling required to meet as far as possible the existing BR2 standard specifications and 235 U content (0.060 g 235 U/cm 2 ). This development phase has been already reported during the 7th RRFM conference (March 9-12, 2003, Aix-en-Provence, France). Afterwards, six lead test fuel elements were ordered for qualification by irradiation. The neutronic properties of the fuel elements were adjusted and optimized. After a short summary of the main results of the development program, this paper describes the nuclear characteristics of the high density fuel elements and comments on the nuclear follow-up of the lead test fuel elements during their irradiation for five cycles in the BR2 reactor and the return of experience for CERCA. (author)

Use of highly enriched uranium in the material testing reactor BR2

International Nuclear Information System (INIS)

Beeckmans de West-Meerbeeck, A.

1979-05-01

In the material testing reactor BR2, the use of highly enriched uranium is determined by the consideration of the fast, epithermal and thermal neutron flux effectively available for the experimental devices. The choice of the core configuration is defined by combining the localisation of the experimental devices and of fuel elements of various burnup, such as to satisfy the irradiation conditions of the experimental load, compatible with an economic use of the fuel elements and safe operation of the reactor. Taking into account the present manufacturing technology for MTR fuels (37 Wt % uranium density in the fuel meat) the highly enriched uranium cannot be avoided; if higher concentration of uranium could be realised by some new manufacturing technology, the 235 U density of fuel elements at elimination should be kept at the required level and the enrichment could be reduced accordingly

Use of highly enriched uranium in the material testing reactor BR2

International Nuclear Information System (INIS)

Beeckmans de West-Meerbeeck, A.

1979-05-01

In the material testing reactor BR2, the use of highly enriched uranium is determined by the consideration of the fast, epithermal and thermal neutron flux effectively available for the experimental devices. The choice of the core configuration is defined by combining the localisation of the experimental devices and of fuel elements of various burnup, such as to satisfy the irradiation conditions of the experimental load, compatible with an economic use of the fuel elements and safe operation of the reactor. Taking into account the present manufacturing technology for MTR fuels (37 Wt % uranium density in the fuel meat) the highly enriched uranium cannot be avoided: if higher concentration of uranium could be realised by some new manufacturing technology, the 235 U density of fuel elements at elimination should be kept at the required level and the enrichment could be reduced accordingly. (author)

Safety challenges encountered during the operating life of the almost 40 year old research reactor BR2

International Nuclear Information System (INIS)

Koonen, E.; Joppen, F.; Gubel, P.

2001-01-01

The BR2 reactor is one of the major MTR-type research reactors in the world. Its operation started in the early 1960's. Two major refurbishment operations have been carried out since then. Several safety reassessments were carried out over the years in order to keep the safety level in line with modern standards and to enhance operational safety. This paper gives an overview of the safety challenges encountered over the years and how those were met. (author)

The bent crystal diffraction spectrometer at the BR2 reactor in Mol

Science.gov (United States)

Kaerts, E.; Jacobs, L.; Vandenput, G.; Van Assche, P. H. M.

1988-05-01

The DuMond-type bent crystal diffraction spectrometer installed at the BR2 reactor in Mol is presented. The spectrometer is mainly designed to study nuclear γ-transitions following thermal neutron capture. It covers the energy interval 25 ≦ Eγ ≦ 1500 keV. Instead of the traditionally used quartz crystals, a highly perfect silicium crystal is chosen as analysing crystal. Diffraction occurs from the (220) plane. The "quasi-mosaic" width, introduced by bending the crystal, is as small as 0.2″. The integrated reflecting power R of the bent crystal stays constant up to 1.5 MeV in first, 680 keV in second and 300 keV in third diffraction order. For higher photon energies, only an E-1 energy dependence is observed in second and third diffraction order. Consequently, besides improving the energy resolution, the use of these silicium crystals substantially increases the spectrometer efficiency and extends the high energy limit of bent crystal diffraction spectrometers. The diffraction angles are measured with a symmetrical interferometer system which covers an angular range of -6° to +6° with a precision of about 0.01″. Minimum diffraction line widths of 0.9″ have been measured, corresponding to an energy resolution ΔE = 1.35 × 10 -6E2n-1 keV -1. The dominant contribution to the observed line widths arises from the finite extent of the source.

First results of the deployment of a SoLid detector module at the SCK•CEN BR2 reactor

Science.gov (United States)

Ryder, N.

The SoLid experiment aims to resolve the reactor neutrino anomaly by searching for electron-to-sterile anti-neutrino oscillations. The search will be performed between 5.5 and 10 m from the highly enriched uranium core of the BR2 reactor at SCK-CEN. The experiment utilises a novel approach to anti-neutrino detection based on a highly segmented, composite scintillator detector design. High experimental sensitivity can be achieved using a combination of high neutron-gamma discrimination using 6 LiF:ZnS(Ag) and precise localisation of the inverse beta decay products. This compact detector system requires limited passive shielding as it relies on spacial topology to determine the different classes of backgrounds. The first full scale, 288 kg, detector module was deployed at the BR2 reactor in November 2014. A phased three tonne experimental deployment will begin in the second half of 2016, allowing a precise search for oscillations that will resolve the reactor anomaly using a three tonne detector running for three years. In this talk the novel detector design is explained and initial detector performance results from the module level deployment are presented along with an estimation of the physics reach of the next phase.

Regulating the Emission Spectrum of CsPbBr3 from Green to Blue via Controlling the Temperature and Velocity of Microchannel Reactor

Directory of Open Access Journals (Sweden)

Yong Tang

2018-03-01

Full Text Available The ability to precisely obtain tunable spectrum of lead halide perovskite quantum dots (QDs is very important for applications, such as in lighting and display. Herein, we report a microchannel reactor method for synthesis of CsPbBr3 QDs with tunable spectrum. By adjusting the temperature and velocity of the microchannel reactor, the emission peaks of CsPbBr3 QDs ranging from 520 nm to 430 nm were obtained, which is wider than that of QDs obtained in a traditional flask without changing halide component. The mechanism of photoluminescence (PL spectral shift of CsPbBr3 QDs was investigated, the result shows that the supersaturation control enabled by the superior mass and heat transfer performance in the microchannel is the key to achieve the wide range of PL spectrum, with only a change in the setting of the temperature controller required. The wide spectrum of CsPbBr3 QDs can be applied to light-emitting diodes (LEDs, photoelectric sensors, lasers, etc.

Review of the accident source terms for aluminide fuel: Application to the BR2 reactor

International Nuclear Information System (INIS)

Joppen, F.

2005-01-01

A major safety review of the BR2, a material test reactor, is to be conducted for the year 2006. One of the subjects selected for the safety review is the definition of source terms for emergency planning and in particular the development of accident scenarios. For nuclear power plants the behaviour of fuel under accident conditions is a well studied object. In case of non-power reactors this basic knowledge is rather scarce. The usefulness of information from power plant fuels is limited due to the differences in fuel type, power level and thermohydraulical conditions. First investigation indicates that using data from power plant fuel leads to an overestimation of the source terms. Further research on this subject could be very useful for the research reactor community, in order to define more realistic source terms and to improve the emergency preparedness. (author)

Measurements of plume geometry and argon-41 radiation field at the BR1 reactor in Mol, Belgium

International Nuclear Information System (INIS)

Drews, M.; Joergensen, H.; Lauritzen, Bent; Mikkelsen, T.; Aage, H.K.; Korsbech, U.; Bargholz, K.; Rojas-Palma, C.; Ammel, R. van

2002-02-01

An atmospheric dispersion experiment was conducted using a visible tracer along with the routine releases of 41 Ar from the BR1 air-cooled research reactor in Mol. In the experiment, simultaneous measurements of the radiation field from the 41 Ar decay, the meteorology, the 41 Ar source term and plume geometry were performed. The visible tracer was injected into the reactor emission stack, and the plume cross section determined by Lidar scanning of the released aerosols. The data collected in the exercise provide a valuable resource for atmospheric dispersion and dose rate modeling. (au)

New control system for BR2. Preventive approach to process control

International Nuclear Information System (INIS)

Van den Branden, G.; Koonen, E.

2011-01-01

In 1961, the BR2 reactor became critical for the first time. Yet the multi-functional research reactor at SCK-CEN is not out of date, quite the contrary. Regular upgrades and innovations keep the reactor in step with the latest advancements in technology. In 2010, the control system of BR2, a vital part of the reactor, was replaced as a preventive measure.

Experimental Irradiations of Materials and Fuels in the BR2 Reactor: An Overview of Current Programmes

International Nuclear Information System (INIS)

Van Dyck, S.; Koonen, E.; Verwerft, M.; Wéber, M.

2013-01-01

The BR2 material test reactor offers a variety of experimental irradiation possibilities for testing of materials, fuels and instruments. The current paper gives an overview of the recent and ongoing programmes in order to illustrate the experimental potential of the reactor. Three domains of applications are reviewed: Irradiation of materials and fuels for pressurised water reactors (PWR); irradiation of materials for accelerator driven systems (ADS), cooled by liquid lead alloys; and irradiation of fuel for Material Test Reactors (MTR). For PWR relevant tests, a dedicated loop is available, providing a full simulation of the thermo hydraulic conditions of a PWR. ADS related tests require particular control of the irradiation environment and the necessary safety precautions in order to avoid 210 Po contamination. In-core mechanical testing of materials is done in comparison and complimentarily to post-irradiation examinations in order to assess flux related effects on the deformation behaviour of materials. (author)

RETRAN02/MOD02: an outside perspective

International Nuclear Information System (INIS)

Wei, T.Y.C.

1984-03-01

ANL recently participated in a review of the RETRAN02/MOD02 code to determine the range of accuracy, the reliability and the reproducibility of results obtained with the code for Chapter 15 non-LOCA system transients for both pressurized water reactors (PWRs) and boiling water reactors (BWRs). This paper summarizes the technical aspects of that review

Draft genome sequence of Bacillus thuringiensis strain BrMgv02-JM63, a chitinolytic bacterium isolated from oil-contaminated mangrove soil in Brazil

NARCIS (Netherlands)

Marcon, Joelma; Taketani, Rodrigo Gouvêa; Dini-Andreote, Francisco; Mazzero, Giulia Inocêncio; Soares Junior, Fabio Lino; Melo, Itamar Soares; Azevedo, João Lúcio; Andreote, Fernando Dini

2014-01-01

Here, we report the draft genome sequence and the automatic annotation of Bacillus thuringiensis strain BrMgv02-JM63. This genome comprises a set of genes involved in the metabolism of chitin and N-acetylglucosamine utilization, thus suggesting the possible role of this strain in the cycling of

Reactor Physics Programme

Energy Technology Data Exchange (ETDEWEB)

De Raedt, C

2000-07-01

The Reactor Physics and Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis on reactor fuel. This expertise is applied within the Reactor Physics and MYRRHA Research Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments. Progress and achievements in 1999 in the following areas are reported on: (1) investigations on the use of military plutonium in commercial power reactors; (2) neutron and gamma calculations performed for BR-2 and for other reactors; (3) the updating of neutron and gamma cross-section libraries; (4) the implementation of reactor codes; (6) the management of the UNIX workstations; and (6) fuel cycle studies.

Reactor Physics Programme

International Nuclear Information System (INIS)

De Raedt, C.

2000-01-01

The Reactor Physics and Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis on reactor fuel. This expertise is applied within the Reactor Physics and MYRRHA Research Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments. Progress and achievements in 1999 in the following areas are reported on: (1) investigations on the use of military plutonium in commercial power reactors; (2) neutron and gamma calculations performed for BR-2 and for other reactors; (3) the updating of neutron and gamma cross-section libraries; (4) the implementation of reactor codes; (6) the management of the UNIX workstations; and (6) fuel cycle studies

The 235U Prompt Fission Neutron Spectrum in the BR1 Reactor at SCK•CEN

Science.gov (United States)

Wagemans, Jan; Malambu, Edouard; Borms, Luc; Fiorito, Luca

2016-02-01

The BR1 research reactor at SCK•CEN has a spherical cavity in the graphite above the reactor core. In this cavity an accurately characterised Maxwellian thermal neutron field is present. Different converters can be loaded in the cavity in order to obtain other types of neutron (and gamma) irradiation fields. Inside the so-called MARK III converter a fast 235U(n,f) prompt fission neutron field can be obtained. With the support of MCNP calculations, irradiations in MARK III can be directly related to the pure 235U(n,f) prompt fission neutron spectrum. For this purpose MARK III spectrum averaged cross sections for the most relevant fluence dosimetry reactions have been determined. A calibration factor for absolute measurements has been determined applying activation dosimetry following ISO/IEC 17025 standards.

The 235U Prompt Fission Neutron Spectrum in the BR1 Reactor at SCK•CEN

Directory of Open Access Journals (Sweden)

Wagemans Jan

2016-01-01

Full Text Available The BR1 research reactor at SCK•CEN has a spherical cavity in the graphite above the reactor core. In this cavity an accurately characterised Maxwellian thermal neutron field is present. Different converters can be loaded in the cavity in order to obtain other types of neutron (and gamma irradiation fields. Inside the so-called MARK III converter a fast 235U(n,f prompt fission neutron field can be obtained. With the support of MCNP calculations, irradiations in MARK III can be directly related to the pure 235U(n,f prompt fission neutron spectrum. For this purpose MARK III spectrum averaged cross sections for the most relevant fluence dosimetry reactions have been determined. A calibration factor for absolute measurements has been determined applying activation dosimetry following ISO/IEC 17025 standards.

Miniature fission chambers calibration in pulse mode: interlaboratory comparison at the. SCK·CEN BR1 and CEA CALIBAN reactors

International Nuclear Information System (INIS)

Lamirand, V.; Geslot, B.; Gregoire, G.; Garnier, D.; Breaud, S.; Mellier, F.; Di-Salvo, J.; Destouches, C.; Blaise, P.; Wagemans, J.; Borms, L.; Malambu, E.; Casoli, P.; Jacquet, X.; Rousseau, G.; Sauvecane, P.

2013-06-01

Miniature fission chambers are suited tools for instrumenting experimental reactors, allowing online and in-core neutron measurements of quantities such as fission rates or reactor power. A new set of such detectors was produced by CEA to be used during the next experimental program at the EOLE facility starting in 2013. Some of these detectors will be employed in pulse mode for absolute measurements, thus requiring calibration. The calibration factor is expressed in mass units and thus called 'effective mass'. A calibration campaign was conducted in December 2012 at the SCK.CEN BR1 facility within the framework of the scientific cooperation VEP (VENUS-EOLE-PROTEUS) between SCK.CEN, CEA and PSI. Two actions were conducted in order to improve the calibration method. First a new characterisation of the thermal flux cavity and the MARK3 neutron flux conversion device performed by SCK.CEN allowed using calculated effective cross sections for determining detectors effective masses. Dosimetry irradiations were performed in situ in order to determine the neutron flux level and provide link to the metrological standard. Secondly two fission chambers were also calibrated at the CEA CALIBAN reactor (fast neutron spectrum), using the same method so that the results can be compared with the results obtained at the SCK.CEN. In this paper the calibration method and recent improvements on uncertainty reduction are presented. The results and uncertainties obtained in the two reactors CALIBAN and BR1 are compared and discussed. (authors)

Irradiation of novel MTR fuel plates in BR2

International Nuclear Information System (INIS)

Verboomen, B.; Aoust, Th.; Beeckmans De Westmeerbeeck, A.; De Raedt, Ch.

2000-01-01

Since the end of 1999, novel MTR fuel plates with very high-density meat are being irradiated in BR2. The purpose of the irradiation is to investigate the behaviour of these fuel plates under very severe reactor operation conditions. The novel fuel plates are inserted in two standard six-tube BR2 fuel elements in the locations normally occupied by the standard outer fuel plates. The irradiation in BR2 was prepared by carrying out detailed neutron Monte Carlo calculations of the whole BR2 core containing the two experimental fuel elements for various positions in the reactor and for various azimuthal orientations of the fuel elements. Comparing the thus determined fission density levels and azimuthal profiles in the new MTR fuel plates irradiated in the various channels allowed the experimenters to choose the most appropriate BR2 channel and the most appropriate fuel element orientation. (author)

Draft Genome Sequence of Bacillus thuringiensis Strain BrMgv02-JM63, a Chitinolytic Bacterium Isolated from Oil-Contaminated Mangrove Soil in Brazil.

Science.gov (United States)

Marcon, Joelma; Taketani, Rodrigo Gouvêa; Dini-Andreote, Francisco; Mazzero, Giulia Inocêncio; Soares, Fabio Lino; Melo, Itamar Soares; Azevedo, João Lúcio; Andreote, Fernando Dini

2014-01-30

Here, we report the draft genome sequence and the automatic annotation of Bacillus thuringiensis strain BrMgv02-JM63. This genome comprises a set of genes involved in the metabolism of chitin and N-acetylglucosamine utilization, thus suggesting the possible role of this strain in the cycling of organic matter in mangrove soils.

Results of water chemistry control in the in-pile ''Callisto'' loop (an experimental PWR rig installed in the BR2 reactor)

International Nuclear Information System (INIS)

Weber, M.; Benoit, P.; Dekeyser, J.; Verwimp, A.

1994-01-01

Since June 1992, a new experimental facility, called CALLISTO, is being irradiated in the BR2 materials testing reactor at Mol, Belgium. The main objective of the present test campaign is to study the behaviour of advanced fuel to high burn-up rates in a realistic PWR environment. Three in-pile sections, containing each 9 fuel rods, are loaded inside the reactor vessel and are connected to a common out-of-pile pressurized water circulation loop (ref.1). The later is branched-off into a purification circuit (feed-bleed concept) and further equipped with safety and auxiliary systems. To cope with the test programme, the equipments are designed so that the guidelines of a PWR primary water chemistry can be followed (ref.2). Real steady-state conditions cannot be observed because the typical BR2 cycle (3 weeks running/3 weeks shut-down) is much shorter and because the rig is cooled down during each reactor shut-down. The purpose of this poster is to provide results of chemical parameters recorded during the cycling behaviour of the CALLISTO primary water. (authors). 4 figs., 1 tab., 2 refs

248 nm photolysis of CH2Br2 by using cavity ring-down absorption spectroscopy: Br2 molecular elimination at room temperature.

Science.gov (United States)

Wei, Pei-Ying; Chang, Yuan-Ping; Lee, Wei-Bin; Hu, Zhengfa; Huang, Hong-Yi; Lin, King-Chuen; Chen, K T; Chang, A H H

2006-10-07

Following photodissociation of CH2Br2 at 248 nm, Br2 molecular elimination is detected by using a tunable laser beam, as crossed perpendicular to the photolyzing laser beam in a ring-down cell, probing the Br2 fragment in the B 3Piou+ -X 1Sigmag+ transition. The nascent vibrational population is obtained, yielding a population ratio of Br2(v = 1)Br2(v = 0) to be 0.7 +/- 0.2. The quantum yield for the Br2 elimination reaction is determined to be 0.2 +/- 0.1. Nevertheless, when CH2Br2 is prepared in a supersonic molecular beam under cold temperature, photofragmentation gives no Br2 detectable in a time-of-flight mass spectrometer. With the aid of ab initio potential energy calculations, a plausible pathway is proposed. Upon excitation to the 1B1 or 3B1 state, C-Br bond elongation may change the molecular symmetry of Cs and enhance the resultant 1 1,3A'-X 1A' (or 1 1,3B1-X 1A1 as C2v is used) coupling to facilitate the process of internal conversion, followed by asynchronous concerted photodissociation. Temperature dependence measurements lend support to the proposed pathway.

Supplemental Thermal-Hydraulic Transient Analyses of BR2 in Support of Conversion to LEU Fuel

Energy Technology Data Exchange (ETDEWEB)

Licht, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-01-01

Belgian Reactor 2 (BR2) is a research and test reactor located in Mol, Belgium and is primarily used for radioisotope production and materials testing. The Materials Management and Minimization (M3) Reactor Conversion Program of the National Nuclear Security Administration (NNSA) is supporting the conversion of the BR2 reactor from Highly Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. The RELAP5/Mod 3.3 code has been used to perform transient thermal-hydraulic safety analyses of the BR2 reactor to support reactor conversion. A RELAP5 model of BR2 has been validated against select transient BR2 reactor experiments performed in 1963 by showing agreement with measured cladding temperatures. Following the validation, the RELAP5 model was then updated to represent the current use of the reactor; taking into account core configuration, neutronic parameters, trip settings, component changes, etc. Simulations of the 1963 experiments were repeated with this updated model to re-evaluate the boiling risks associated with the currently allowed maximum heat flux limit of 470 W/cm² and temporary heat flux limit of 600 W/cm². This document provides analysis of additional transient simulations that are required as part of a modern BR2 safety analysis report (SAR). The additional simulations included in this report are effect of pool temperature, reduced steady-state flow rate, in-pool loss of coolant accidents, and loss of external cooling. The simulations described in this document have been performed for both an HEU- and LEU-fueled core.

Radiobiological aspects of application of BR-10 reactor neutrons for radiotherapy of malignant tumours

International Nuclear Information System (INIS)

Ul'yanenko, S.E.; Kuznetsova, M.N.; Obaturov, G.M.

1992-01-01

Possibilities to increase the factor of therapeutical gain (FTG) by optimizing irradiation conditions and using hyperglycemia were studied. It is shown that relative biological effectiveness (RBE) of neutrons in fission spectrum of the BR-10 reactor in the dose range from 10 Gy used one time is 4.2-4.5 for tumours and 4.0-4.2 for normal skin; in case of fractionated irradiation by neutrons (1-8 fractions in the range of 6-10 Gy) RBE increases practically 1.5 fold; employment of neutron beam filters and hyperglycemia in conditions of combined gamma-neutron procedures of irradiation permits a considerable increase in FTG. 3 refs

Reactor Physics

International Nuclear Information System (INIS)

Ait Abderrahim, A.

2002-01-01

SCK-CEN's Reactor Physics and MYRRHA Department offers expertise in various areas of reactor physics, in particular in neutron and gamma calculations, reactor dosimetry, reactor operation and control, reactor code benchmarking and reactor safety calculations. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 materials testing reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2001 are summarised

Reactor Physics

Energy Technology Data Exchange (ETDEWEB)

Ait Abderrahim, A

2001-04-01

The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised.

Reactor Physics

International Nuclear Information System (INIS)

Ait Abderrahim, A.

2001-01-01

The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised

Angular correlation for gamma-gamma transitions in 81Br and 83Br nuclei

International Nuclear Information System (INIS)

Matheus, R.

1984-01-01

The directional angular correlation of coincident gamma transitions in 81 Br and 83 Br have been measured following the β - decay of 81 Se(T sub(1/2) = 18.6 min) and 83 Se(T sub(1/2) = 22.6 min) respectively, using Ge(Li) - high purity Ge and Ge(Li)-NaI(Tl) spectrometers. The radioactive sources were prepared by irradiating with neutrons in the IEA-R1 reactor, metallic selenium (natural) to produce 81 Se and samples of metallic selenium enriched (to approx. 90% in 82 Se) to produce 83 Se. Measurements have been carried out for the gamma cascades 260-276 KeV, 290-276 KeV and 552-276 KeV in 81 Br and the gamma cascades 225(510)-356 KeV, 510-356 KeV, 572-(510)-356 KeV, 718-(225)-(510)-356 KeV, 1064-356 KeV, 718-225 KeV, 718-(225)-510 KeV, 836-718 KeV, 718-(225)-866 KeV, 883-718 KeV and 1895-799 KeV in 83 Br. The multipole mixing ratios, σ(E2/M1), were determined for 3 gamma transitions in 81 Br and 11 gamma transitions in 83 Br. In the case of 81 Br present results confirmed some of the earlier results. The spin and parity assignment were made to the majority of levels in 81 Br and 83 Br involved in the present study, some of them confirming the earlier results. A comparison of some of the nuclear properties of the 79 Br, 81 Br and 83 Br is made based on the available experimental data. The experimental results are also discussed qualitatively in terms of some nuclear models applicable for the description of the properties of odd-A bromine isotopes. (Author) [pt

SoLid: An innovative anti-neutrino detector for searching oscillations at the SCK•CEN BR2 reactor

Science.gov (United States)

Abreu, Yamiel; SoLid Collaboration

2017-02-01

The SoLid experiment intends to search for active-to-sterile anti-neutrino oscillations at a very short baseline from the SCK•CEN BR2 research reactor (Mol, Belgium). A novel detector approach to measure reactor anti-neutrinos was developed based on an innovative sandwich of composite polyvinyl-toluene and 6LiF:ZnS(Ag) scintillators. The system is highly segmented and read out by a network of wavelength shifting fibers and SiPM. High experimental sensitivity can be achieved compared to other standard technologies thanks to the combination of high granularity, good neutron-gamma discrimination using 6LiF:ZnS(Ag) scintillator and precise localisation of the Inverse Beta Decay products. This technology can be considered as a new generation of an anti-neutrino detector. This compact system requires limited passive shielding and relies on spatial topology to determine the different classes of backgrounds. We will describe the principle of detection and the detector design. Particular focus on the neutron discrimination will be made, as well as on the capability to use cosmic muons for channel equalisation and energy calibration. The performance of the first 288 kg SoLid module (SM1), based on the data taken at BR2 from February to September 2015, will be presented. We will conclude with the next phase, which will start in 2016, and the future plans of the experiment.

Reactor Physics

Energy Technology Data Exchange (ETDEWEB)

Ait Abderrahim, A

2002-04-01

SCK-CEN's Reactor Physics and MYRRHA Department offers expertise in various areas of reactor physics, in particular in neutron and gamma calculations, reactor dosimetry, reactor operation and control, reactor code benchmarking and reactor safety calculations. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 materials testing reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2001 are summarised.

BR2 mixed core management

International Nuclear Information System (INIS)

Ponsard, B.; Beeckmans, A.

1997-01-01

The BR2 fuel cycle management can be optimized by the fabrication and the irradiation of fuel elements with uranium recovered from the reprocessing of BR2 spent fuel. The VIn E fuel performances could be upgraded by increasing the amount of burnable poisons, the fuel mass, the fuel density, ... in order to obtain a higher reactivity effect at a burnup of about β=12% and a longer cycle duration. The preliminary results of the calculations need however to be confirmed by measurements on effective reactor loads. (author)

A pilot application of the RELAP file to the steady state and transient analysis of a test section inside the BR2 reactor

International Nuclear Information System (INIS)

Ferri, M. G.; D'Auria, F.; Forasassi, G.; Giot, M.

2000-01-01

BR2 is a material test reactor sited in the Belgian Nuclear Research Centre in Mol. The main research programs carried out in BR2 are related to the safety of nuclear reactor structural materials and fuels, in normal and accidental conditions, plant lifetime evaluation and ageing of components. In this framework, a computer program that allows the performance of detailed, steady state analysis of several kinds of in-pile sections with an axisymmetrical geometry has been developed. Furthermore, comparing its results with those of the well known, extensively used, Relap5/Mod 3.2 code on a test problem has validated this program. This was performed in three steps: 1. modalisation development of a subsystem of a typical in-pile section. 2. steady state analysis and comparison with the above-mentioned program. 3. transient simulation of the same system; the considered transient consists of a loss of coolant flow. (author)

The utility of different reactor types for the research

International Nuclear Information System (INIS)

Stiennon, G.

1983-01-01

The report presents a general view of the use of the different belgian research reactor i.e. venus reactor, BR-1 reactor, BR-2 reactor and BR-3 reactor. Particular attention is given to the programmes which is in the interest of international collaboration. In order to reach an efficient utilization of such reactors they require a specialized personnel groups to deal with the irradiation devices and radioactive materials and post irradiation examinations, creating a complete material testing station. (A.J.)

Assessment of the French and US embrittlement trend curves applied to RPV materials irradiated in the BR2 materials test reactor

International Nuclear Information System (INIS)

Chaouadi, R.; Gerard, R.; Boagaerts, A.S.

2011-01-01

The irradiation embrittlement of reactor pressure vessels (RPVs) in monitored through the surveillance programs associated with predictive formulas, the so-called embrittlement trend curves. These formulas are generally empirically derived and contain the major embrittlement-inducing elements such as copper, nickel and phosphorus. There are a number of such trend curves used in various regulatory guides used in the US, France, Germany, Russia and Japan. These trend curves are often supported by surveillance data and regularly assessed in view of updated surveillance databases. With the recent worldwide move towards life extension of existing reactors above their initially-scheduled lifetime of 40 years, adequate and accurate modeling of irradiation embrittlement becomes a concern for long term operation. The aim of this work is to assess the performance of the embrittlement trend curves used in a regulatory perspective. The work presented here is limited to US and French trend curves because the reactor pressure vessels of the Belgian nuclear power plants are either Westinghouse or Framatome design. The chemical composition of the Belgian RPVs being very close to the one of the French 900 MW units, the French trend curve is used except for the Doel 1-2 units for which these curves are not applicable due to the higher copper content of the welds. In this case, the U.S. trend curves are used. The aim of this work is to evaluate the performance of the embrittlement trend curves used in a regulatory perspective to represent the experimental data obtained in the BR2 reactor. In particular, the French (FIM, FIS) and the US (Reg. Guide 1.99 Rev. 2, ASTM E900-02, EWO and EONY) formulas are of prime interest. The results obtained clearly show that the French trend curves tend to over-estimate the actual irradiation hardening while the US curves under-estimate it. Within the long term operation perspective, both over- and under-estimating are undesirable and therefore the

The possibilities of application of experimental Kfk results from BR2 on SNR designs

International Nuclear Information System (INIS)

Karsten, G.; Elbel, K.; Dienst, W.; Schaefer, L.

1978-01-01

A review is given of the relevant results of the technological application for the SNR300 reactor, since the BR2 reactor has been used as a test facility for the material development. Special emphasis has been laid on the fuel pin behavior under the aspect of chemical and mechanical fuel-clad interaction and on the specification of the cladding in terms of high temperature mechanical behavior in the SNR 300 reactor. A systematic analysis of urgent research topics in BR2 test facility reactor is presented. (A.F.)

SoLid: An innovative anti-neutrino detector for searching oscillations at the SCK• CEN BR2 reactor

Energy Technology Data Exchange (ETDEWEB)

Abreu, Yamiel, E-mail: yamiel.abreu@uantwerpen.be

2017-02-11

The SoLid experiment intends to search for active-to-sterile anti-neutrino oscillations at a very short baseline from the SCK• CEN BR2 research reactor (Mol, Belgium). A novel detector approach to measure reactor anti-neutrinos was developed based on an innovative sandwich of composite polyvinyl-toluene and {sup 6}LiF:ZnS(Ag) scintillators. The system is highly segmented and read out by a network of wavelength shifting fibers and SiPM. High experimental sensitivity can be achieved compared to other standard technologies thanks to the combination of high granularity, good neutron–gamma discrimination using {sup 6}LiF:ZnS(Ag) scintillator and precise localisation of the Inverse Beta Decay products. This technology can be considered as a new generation of an anti-neutrino detector. This compact system requires limited passive shielding and relies on spatial topology to determine the different classes of backgrounds. We will describe the principle of detection and the detector design. Particular focus on the neutron discrimination will be made, as well as on the capability to use cosmic muons for channel equalisation and energy calibration. The performance of the first 288 kg SoLid module (SM1), based on the data taken at BR2 from February to September 2015, will be presented. We will conclude with the next phase, which will start in 2016, and the future plans of the experiment.

Reactor Division semestrial progress report January - June 1987

International Nuclear Information System (INIS)

1987-01-01

This report covers the activities of the reactor division at the SCK-CEN during the first semester of 1987. It deals with the BR-2 materials testing reactor, the BR-3 power plant, reactor physics, water cooled reactors, fast neutron reactors, fusion, non nuclear programmes, testing and commissioning, high and medium activities, and informatics. (MCB)

Reactor Division semestrial progress report July - December 1987

International Nuclear Information System (INIS)

1987-01-01

This report covers the activities of the reactor division at the SCK-CEN during the second semester of 1987. It deals with the BR-2 materials testing reactor, the BR-3 power plant, reactor physics, water cooled reactors, fast neutron reactors, fusion, non nuclear programmes, testing and commissioning, high and medium activities, and informatics. (MCB)

Mechanical behaviour of Br0.5Sr0.5Co0.8Fe0.2O3-δ under uniaxial compression

International Nuclear Information System (INIS)

Araki, Wakako; Malzbender, Jürgen

2013-01-01

The present study reports on the mechanical behaviour of Br 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3-δ under uniaxial compression at various temperatures. The stress–strain curve at room temperature shows a small but clear creep deformation, along with a hysteresis and a remnant strain, which could be related to a spin transition of cobalt. The hysteresis as well as Young’s modulus decrease with increasing temperature to 473 K, at which temperature the creep behaviour disappears. The material shows conventional high-temperature creep above 673 K

The post irradiation examination of a sphere-pac (UPu)C fuel pin irradiated in the BR-2 reactor (MFBS 7 experiment)

International Nuclear Information System (INIS)

Smith, L.; Aerne, E.T.; Buergisser, B.; Flueckiger, U.; Hofer, R.; Petrik, F.

1979-09-01

A pin fuelled with Swiss made (UPu)C microspheres has been successfully irradiated to a peak burn-up of 6% fima in the Belgian BR2 Reactor. The pin, rated up to 95 kW/m, was intact after irradiation and exhibited a peak strain of just over 0.5%. The results of the post irradiation examination are reported. (Auth.)

Operation of the BR2 Reactor

International Nuclear Information System (INIS)

Gubel, P.

2006-01-01

The BR2 is still SCK-CEN's most important nuclear facility. After an extensive refurbishment of 22 months to compensate for the ageing of the installations, to enhance the reliability of operation and to comply with modern safety standards, it was restarted in April 1997. The facility is mainly used for the irradiation and testing of fuels and materials and for commercial productions - including radioisotopes for the medical and industrial uses, and NTD-Silicon. The article describes the main achievements and activities in 2005

Operation of the BR2 Reactor

International Nuclear Information System (INIS)

Gubel, P.

2005-01-01

The BR2 is still SCK-CEN's most important nuclear facility. After an extensive refurbishment of 22 months to compensate for the ageing of the installations, to enhance the reliability of operation and to comply with modern safety standards, it was restarted in April 1997. The facility is mainly used for the irradiation and testing of fuels and materials and for commercial productions - including radioisotopes for the medical and industrial uses, and NTD-Silicon. The article describes the main activities and achievements in 2004

Cooperation of nuclear reactor controller ARM-5S and turbine TVER-02

International Nuclear Information System (INIS)

Wagner, K.; Lnenicka, B.; Pokorny, F.; Prochazka, F.

1985-01-01

Turbines of Czechoslovak make provided with controllers TVER-02 are installed in WWER-440 nuclear power plants under construction in Czechoslovakia. Reactor output is controlled using Soviet-made controllers ARM-5S which already comprise turbine controllers. The problems are analyzed of cooperation of both controllers, especially their parameters and transient processes in typical operating situations. The analysis uses the results of measurements performed during the power start-up of Unit 1 of the V-2 nuclear power plant at Jaslovske Bohunice. The results show that two types of control modes can be selected for the operation of the entire unit: the control to constant unit output, and control of unit output varying with turbine load selected on the TVER-02 controller or given by the demand of the power network. (Z.M.)

Scientific activities in support of the BR2 operation and irradiation programmes

International Nuclear Information System (INIS)

Koonen, E.

2006-01-01

One of the major characteristics of the BR2 reactor is the fact that the core configuration is essentially variable. This allows to optimize the irradiation conditions of various experiments and to minimize the fuel consumption. In order to do that, BR2 has its own autonomous reactor physics cell. In order to allow for on-line measurements of the major irradiation parameters, BR2 has extended its own proven data acquisition system to serve this purpose. This system, called BIDASSE (for BR2 Integrated Data Acquisition System for Survey and Experiments), originally designed for the follow-up of all BR2 operational parameters, is since several years extensively used for experiments. The object rives of research at the BR2 are to evaluate and adjust provisional irradiation conditions by adjustments of the environment, axial and azimuthal positioning of the samples, global power level, ... ; to deliver reliable, well defined irradiation condition and fluence data during and after irradiation; to assist the designer of new irradiation devices by simulations and neutronic optimisations of design options and o provide the experimenters with accurate on-line information on the evolution of their ongoing irradiation projects

Refurbishment of BR2 (Phases 4 and 5)

Energy Technology Data Exchange (ETDEWEB)

Gubel, P.; Dekeyser, J.; Van Der Auwera, J

1998-07-01

The BR2 is a materials testing reactor and is SCK-CEN's most important nuclear facility. After an extensive refurbishment to compensate for the ageing of the installation, the reactor was restarted in April 1997. In phase 4 of the refurbishment programme, various activities were performed to allow reactor start-up. In phase 5, remaining refurbishment works were carried out as well as the extra studies and upgradings required by the licensing authorities. Major achievements in 1997 are described and discussed.

Refurbishment of BR2 (Phases 4 and 5)

International Nuclear Information System (INIS)

Gubel, P.; Dekeyser, J.; Van Der Auwera, J.

1998-01-01

The BR2 is a materials testing reactor and is SCK-CEN's most important nuclear facility. After an extensive refurbishment to compensate for the ageing of the installation, the reactor was restarted in April 1997. In phase 4 of the refurbishment programme, various activities were performed to allow reactor start-up. In phase 5, remaining refurbishment works were carried out as well as the extra studies and upgradings required by the licensing authorities. Major achievements in 1997 are described and discussed

Refurbishment of BR2 (Phases 4 and 5)

Energy Technology Data Exchange (ETDEWEB)

Gubel, P; Dekeyser, J; Van Der Auwera, J

1998-07-01

The BR2 is a materials testing reactor and is SCK-CEN's most important nuclear facility. After an extensive refurbishment to compensate for the ageing of the installation, the reactor was restarted in April 1997. In phase 4 of the refurbishment programme, various activities were performed to allow reactor start-up. In phase 5, remaining refurbishment works were carried out as well as the extra studies and upgradings required by the licensing authorities. Major achievements in 1997 are described and discussed.

Life extension of the BR2 aluminium vessel

International Nuclear Information System (INIS)

Koonen, E.; Fabry, A.; Chaouadi, R.; Verwerft, M.; Raedt, C. de; Winckel, S. van; Wacquier, W.; Dadoumont, J.; Verwimp, A.

2000-01-01

The BR2 reactor has recently undergone a major refurbishment comprising the replacement of all vessel internals. The vessel itself however was not replaced. An important requalification programme has been executed to prove that the vessel would remain fit during the contemplated life extension period of BR2. Representative material samples could be obtained from the shroud surrounding the vessel. A comprehensive in-service inspection was carried out and a vessel surveillance programme has been established. (author)

Hydrogen-bonded structure in highly concentrated aqueous LiBr solutions

International Nuclear Information System (INIS)

Imano, Masahiro; Kameda, Yasuo; Usuki, Takeshi; Uemura, Osamu

2001-01-01

Neutron diffraction measurements were carried out for H/D isotopically substituted aqueous 10, 25 and 33 mol% LiBr solutions in order to obtain structural information on the intermolecular hydrogen bonds among water molecules in highly concentrated aqueous solutions. Observed scattering cross sections for D 2 O (99.9 % D), 0 H 2 O(35.9 % D) and 0-2 H 2 O(68.0 % D) solutions were combined to deduce partial structure factors, a HH (Q), a XH (Q) and a XX (Q) (X: O, Br and Li). The least squares fitting analysis was applied to the observed partial structure factors to determine the nearest neighbor interatomic distance, root-mean-square amplitude and coordination number. Intermolecular distances, r OH =1.91(1) A, r HH =2.38(1) A and r OO =3.02(1) A, between the nearest neighbor water molecules, were obtained for the 10 mol% LiBr solution. On the other hand, the intermolecular O···H interaction was found to almost disappear in concentrated 25 and 33 mol% LiBr solutions. The result implies that the hydrogen-bonded network is completely broken in highly concentrated aqueous LiBr solutions. (author)

Pellet bed reactor for nuclear thermal propelled vehicles

International Nuclear Information System (INIS)

El-Genk, M.; Morley, N.J.; Haloulakos, V.E.

1991-01-01

The Pellet Bed Reactor (PeBR) concept is capable of operating at a high power density of up to 3.0 kWt/cu cm and an exit hydrogen gas temperature of 3000 K. The nominal reactor thermal power is 1500 MW and the reactor core is 0.80 m in diameter and 1.3 m high. The nominal PeBR engine generates a thrust of approximately 315 kN at a specific impulse of 1000 s for a mission duration to Mars of 250 days requiring a total firing time of 170 minutes. Because of its low diameter-to-height ratio, PeBR has enough surface area for passive removal of the decay heat from the reactor core. The reactor is equipped with two independent shutdown mechanisms; 8-B4C safety rods and 26 BeO/B4C control drums; each system is capable of operating and scraming the reactor safely. Due to the absence of core internal support structures, the PeBR can be fueled and refueled in orbit using the vacuum of space. These unique features of the PeBR provide for safety during launch, simplicity of handling, deployment, and end-of-life disposal, and vehicle extended lifetime. 11 refs

On-line fast flux measurements in the BR2 reactor

International Nuclear Information System (INIS)

Vermeeren, L.

2009-01-01

Since 2001, CEA-Cadarache and the Belgian Nuclear Research Centre SCK-CEN are collaborating on the development and in-pile qualification of subminiature fission chambers (diameter of 1.5 mm). Initially, efforts concentrated on fission chambers for the in-pile measurement of thermal fluxes (with 235 U as fissile material). Meanwhile successful long-term tests of the prototypes have been performed in various environments: in low temperature (40-100 degress Celsius) BR2 pool water (up to a thermal neutron fluence of 3 1 0 21 n/cm 2 ) and in the CALLISTO PWR loop (300 degrees Celsius, 155 bars). The long-term qualification of derived industrial detectors (Photonis CFUZ53) in CALLISTO is still ongoing. However, for various types of irradiations in research reactors, the knowledge of the evolution of the fast neutron flux is even of more interest than the thermal flux data. Therefore the collaboration program was extended to the development and the in-pile qualification of subminiature or miniature fission chambers (with 3 mm diameter) for fast neutron detection, for which 242 Pu was selected as the optimal fissile material. In order to achieve the on-line in-pile measurement of fast neutron flux, the fission chambers will be operated in the Campbelling mode (based on the mean square fluctuation of the detector current). In this mode the gamma induced contribution to the signal can be efficiently suppressed. Moreover, a data processing software will take into account the evolution of the fissile deposit in order to assess on-line the fast flux sensitivity and to correct for the low energy neutron contributions. The final objective is to qualify a Fast Neutron Detector System (FNDS) able to provide on-line data for local fast neutron fluxes in Material Testing Reactors. The on-line measurement of the fast neutron flux would contribute significantly to the characterization of the irradiation conditions during test experiments with materials and innovative fuel elements

Oxidation mechanisms of CF2Br2 and CH2Br2 induced by air nonthermal plasma.

Science.gov (United States)

Schiorlin, Milko; Marotta, Ester; Dal Molin, Marta; Paradisi, Cristina

2013-01-02

Oxidation mechanisms in air nonthermal plasma (NTP) at room temperature and atmospheric pressure were investigated in a corona reactor energized by +dc, -dc, or +pulsed high voltage.. The two bromomethanes CF(2)Br(2) and CH(2)Br(2) were chosen as model organic pollutants because of their very different reactivities with OH radicals. Thus, they served as useful mechanistic probes: they respond differently to the presence of humidity in the air and give different products. By FT-IR analysis of the postdischarge gas the following products were detected and quantified: CO(2) and CO in the case of CH(2)Br(2), CO(2) and F(2)C ═ O in the case of CF(2)Br(2). F(2)C ═ O is a long-lived oxidation intermediate due to its low reactivity with atmospheric radicals. It is however removed from the NTP processed gas by passage through a water scrubber resulting in hydrolysis to CO(2) and HF. Other noncarbon containing products of the discharge were also monitored by FT-IR analysis, including HNO(3) and N(2)O. Ozone, an important product of air NTP, was never detected in experiments with CF(2)Br(2) and CH(2)Br(2) because of the highly efficient ozone depleting cycles catalyzed by BrOx species formed from the bromomethanes. It is concluded that, regardless of the type of corona applied, CF(2)Br(2) reacts in air NTP via a common intermediate, the CF(2)Br radical. The possible reactions leading to this radical are discussed, including, for -dc activation, charge exchange with O(2)(-), a species detected by APCI mass spectrometry.

Thermodynamic assessment of EuBr2 unary and LiBr-EuBr2 and NaBr-EuBr2 binary systems

International Nuclear Information System (INIS)

Gong, Weiping; Gaune-Escard, Marcelle

2009-01-01

As a basis for the design and development of molten salt mixtures, thermodynamic calculations of the phase diagrams and thermodynamic properties were carried out on the EuBr 2 unary and LiBr-EuBr 2 and NaBr-EuBr 2 binary systems over a wide temperature and composition range, respectively. The Gibbs energy of EuBr 2 was evaluated using an independent polynomial to fit the experimental heat capacity, the thermodynamic parameters for each phase in the LiBr-EuBr 2 and NaBr-EuBr 2 systems were optimized by using available experimental information on phase diagrams. A regular substitutional solution model for the liquid phase and Neumann-Kopp rule for the stoichiometric compound LiEu 2 Br 5 were adopted to reproduce the experimental data with reasonable excess Gibbs energy. Comparisons between the calculated phase diagrams and thermodynamic quantities show that all reliable experimental information is satisfactorily accounted for by the present thermodynamic description. Some thermodynamic properties were predicted to check the suitability of the present calculation.

Determination of nuclear cross-section of 81Br (n,,,) Br82 reaction by ...

African Journals Online (AJOL)

... flux of 4.2 x 1013 n cm-2 s-1. The BaBr2 was chemically processed and measured as Hydrogen Bromide (HBr82). The value of nuclear cross-section was determined to be 2.1 0.2 barns, which falls within the range of values as previously reported elsewhere. (Journal of Applied Science and Technology: 2001 6(1-2): 4-6) ...

Influence of cold work to increase swelling of pure iron irradiated in the BR-10 reactor to ∼6 and ∼25 dpa at ∼400 deg. C

International Nuclear Information System (INIS)

Dvoriashin, A.M.; Porollo, S.I.; Konobeev, Yu.V.; Garner, F.A.

2000-01-01

Irradiation of pure iron in several starting conditions at 400 deg. C has been conducted in the BR-10 fast reactor. Contrary to expectations, cold working appears to significantly accelerate the onset of void swelling. When compared to a similar experiment conducted in this reactor at the same time, it appears that iron experiences a rather long transient duration before the onset of steady-state swelling. The transient appears to be shortened by both cold-working and lower atomic displacement rates

Status of the BR2 refurbishment programme

International Nuclear Information System (INIS)

Koonen, E.

1995-01-01

The operation of the BR2 reactor with its second beryllium matrix is foreseen up to mid-1995. A refurbishment programme has been established in order to allow for future operation during at least ten years. Recently a positive decision to effectively carry out this programme has been taken. The refurbishment action plan follows from a general assessment of the different systems of BR2, with respect to their actual status, the operational experience and the evolution of safety standards and criteria. Ageing considerations were of uppermost importance in those assessments, not only to assure safety of future operation, but also to guarantee future availability and reliability. (orig.)

Reactor gamma spectrometry: status

International Nuclear Information System (INIS)

Gold, R.; Kaiser, B.J.

1979-01-01

Current work is described for Compton Recoil Gamma-Ray Spectrometry including developments in experimental technique as well as recent reactor spectrometry measurements. The current status of the method is described concerning gamma spectromoetry probe design and response characteristics. Emphasis is given to gamma spectrometry work in US LWR and BR programs. Gamma spectrometry in BR environments are outlined by focussing on start-up plans for the Fast Test Reactor (FTR). Gamma spectrometry results are presented for a LWR pressure vessel mockup in the Poolside Critical Assembly (PCA) at Oak Ridge National Laboratory

The probability safety assessment impact on the BR2 refurbishment

International Nuclear Information System (INIS)

Pouleur, Yvan

1995-01-01

The probabilistic safety assessment (PSA) study has proven its worth by establishing a sensitive safety screening of the reactor. It has focused engineering forces to technically improve safety systems and to measure the influence of functional modifications. In the future, the project will be developed in a living way, to reinforce the present structure along with continuous safety monitoring of the reactor and to develop engineers and operators safety skills. This paper presents the PSA impact on the BR2 (Belgian Reactor Two) refurbishment. (author)

Management and storage of nuclear fuel from Belgian research reactors

International Nuclear Information System (INIS)

Gubel, P.

1996-01-01

Experiences and problems with the storage of irradiated fuel at research reactors in Belgium are described. In particular, interim storage problems exist for spent fuel elements at the BR2 and the shut down BR3 reactors in Mol. (author). 1 ref

Louisiana SIP: LAC 33:III Ch 21 Subchap J, 2147--Limiting Volatile Organic Compound (VOC) Emissions from Reactor Processes and Distillation Operations in Synthetic Organic Chemical manufacturing Industry (SOCMI); SIP effective 1998-02-02 (LAc74) to more..

Science.gov (United States)

Louisiana SIP: LAC 33:III Ch 21 Subchap J, 2147--Limiting Volatile Organic Compound (VOC) Emissions from Reactor Processes and Distillation Operations in Synthetic Organic Chemical manufacturing Industry (SOCMI); SIP effective 1998-02-02 (LAc74) more...

Decommissioning of the BR3 PWR

International Nuclear Information System (INIS)

Massaut, V.

1998-01-01

The dismantling and the decommissioning of nuclear installations at the end of their life-cycle is a new challenge to the nuclear industry. Different techniques and procedures for the dismantling of a nuclear power plant on an existing installation, the BR-3 pressurized-water reactor, are described. The scientific program, objectives, achievements in this research area at the Belgian Nuclear Research Centre SCK-CEN for 1997 are summarized

The BR2 refurbishment: from concept to achievements

International Nuclear Information System (INIS)

Gubel, P.

2002-01-01

The BR2 reactor is one of the major research reactors in the world. It's operation started in the early 1960's. Two major refurbishments operation have been carried out since then. The report gives an overview of the methodology and inspections, which resulted in a refurbishment action plan. The main realizations and complementary actions required by the Licensing Authorities are summarized. Finally the operation experience feedback, four years now after start-up, is briefly discussed as well as the main aspects of the present safety reassessment [ru

Electronic structure of Co(III) doped bromo-bridged Ni complexes, [Ni1-xCox(chxn)2Br]Br2.

Science.gov (United States)

Xie, Jimin; Wu, Hashen; Kawakami, Daisuke; Iguchi, Hiroaki; Takaishi, Shinya; Yamashita, Masahiro; Matsuzaki, Hiroyuki; Okamoto, Hiroshi; Tanaka, Hisaaki; Kuroda, Shin-ichi

2008-03-17

This article describes the electronic structure of the Co(III) doped Br bridged Ni(III) complexes, [Ni(1-x)Cox(chxn)2Br]Br2 (x = 0.01, 0.02, 0.05, and 0.11) by using a optical spectroscopy, scanning tunneling microscopy (STM), and electron spin resonance spectroscopy. In the optical reflectivity spectrum, the new band was formed at about 0.5 eV, which is reasonably recognized as the d(z2) band of doped Co(III) ions. In the STM images of [Ni(1-x)Cox(chxn)2Br]Br2, the bright spots attributable to the tunnel current from the Fermi level of the STM tip to the conduction band of the sample were observed. In addition, some brighter spots were also observed. Because the number of the brighter spots is in good agreement with that of doped Co species, the brighter spots can be assigned to doped Co(III) sites. These are reasonably explained by the tunnel current from the Fermi level of the tip to the d(z2) band of Co(III). The Curie spin concentration was gradually increased with increasing Co(III) ions, which is explained by the scissions of the S = 1/2 1D antiferromagnetic chains.

The management routes for materials produced by the dismantling of the BR3-PWR reactor

International Nuclear Information System (INIS)

Klein, M.; Demeulemeester, Y.; Ponnet, M.; Emond, M.; Emond, O.; Dadoumont, J.; Massaut, V.

2000-01-01

The dismantling of the BR3 reactor produces quite large masses of contaminated materials, mainly metals or concrete. The main management routes are: conditioning of the radioactive wastes and disposal, recycling of radioactive materials in the nuclear sector and the recycling of free released materials in the industrial sector or their evacuation as industrial waste. The conditioning of the radioactive wastes is essentially performed in the installations of Belgoprocess and must follow the specifications imposed by the national radwaste management agency ONDRAF/NIRAS. The conditioning of the pieces produced during the cutting of the reactor pressure vessel is given as example. The recycling of radioactive materials in the nuclear sector is possible for metals and for concrete. For metals, SCK.CEN has an agreement with a nuclear foundry which reuses these materials for the fabrication of shieldings. For concrete, an R and D programme is going on with the objective to demonstrate the possible reuse of baryte concrete as raw materials for the production of mortar used in the conditioning of radioactive wastes. The free release of radioactive materials and their reuse or evacuation as radioactive wastes requires the strict respect of procedures and the use of low level measurement techniques. Various decontamination techniques are used at SCK.CEN to reach this objective. For the metals, we use mainly simple washing, abrasive decontamination and hard chemical decontamination. For concrete, we use mainly scabbling or shaving techniques. (authors)

Thermodynamic assessment of NdBr3 unary and LiBr-NdBr3 binary system

International Nuclear Information System (INIS)

Gong Weiping; Gaune-Escard, Marcelle

2006-01-01

Phase diagram and thermodynamic properties calculations were carried out on the NdBr 3 unary and the LiBr-NdBr 3 binary systems over the entire temperature and composition range, respectively. The Gibbs energy of NdBr 3 was evaluated using an independent polynomial to fit the experimental thermodynamic properties. The liquid phase in the LiBr-NdBr 3 system was described by the two sub-lattice ionic solution model (Li + ) P : (Br - , NdBr 6 -3 , NdBr 3 ) Q . Comparisons between the calculated phase diagram and thermodynamic quantities show that all reliable experimental information was satisfactorily accounted for by the present thermodynamic description

A precise investigation of the 76Br decay for PET imaging

Science.gov (United States)

Moran, K.; Lister, C. J.; Chowdhury, P.; McCutchan, E. A.; Sonzogni, A.; Broder, B.; Nickles, R. J.; Ellison, P.; Zhu, S.; Greene, J. P.

2016-09-01

Radioisotopes are used in over 14 million medical imaging and therapy procedures each year. New isotopes are constantly introduced to optimize targeting or decay radiation. The dose of internal radiation is calculated from data which in some cases have not been updated for several decades. A thorough investigation of these isotopes using modern technologies and improved analysis techniques is vital to ensure accurate quantification of dose to patients. In this work, we explore the decay of 76Br, a β+ emitter for PET (positron emission tomography), which is used with 77Br for therapy. A sample containing several isotopes of interest, including 76,77Br, was produced at the University of Wisconsin Medical School, shipped to Argonne National Lab, and assayed for 7 days using the Gammasphere detector array, running both analog and digital data acquisition systems simultaneously. More than 6 terabytes of data were collected from the 1MBq source. Analysis of this data set shows new strength to high-lying levels, and allows a reappraisal of the received dose as well as an investigation of count-rate advantages of digital Gammasphere. Supported by US DOE under Grant DE-FG02-94ER40848 and Contracts No. DE-AC02-06CH11357 and No. DE-AC02-98CH10946.

Development of a BR-UASB-DHS system for natural rubber processing wastewater treatment.

Science.gov (United States)

Watari, Takahiro; Thanh, Nguyen Thi; Tsuruoka, Natsumi; Tanikawa, Daisuke; Kuroda, Kyohei; Huong, Nguyen Lan; Tan, Nguyen Minh; Hai, Huynh Trung; Hatamoto, Masashi; Syutsubo, Kazuaki; Fukuda, Masao; Yamaguchi, Takashi

2015-11-21

Natural rubber processing wastewater contains high concentrations of organic compounds, nitrogen, and other contaminants. In this study, a treatment system composed of a baffled reactor (BR), an upflow anaerobic sludge blanket (UASB) reactor, and a downflow hanging sponge (DHS) reactor was used to treat natural rubber processing wastewater in Vietnam. The BR showed good total suspended solids removal of 47.6%, as well as acidification of wastewater. The UASB reactor achieved a high chemical oxygen demand (COD) removal efficiency of 92.7% ± 2.3% and energy recovery in the form of methane with an organic loading rate of 12.2 ± 6.6 kg-COD·m -3 ·day -1 . The DHS reactor showed a high performance in residual organic matter removal from UASB effluent. In total, the system achieved high-level total COD removal of 98.6% ± 1.2% and total suspended solids removal of 98.0% ± 1.4%. Massive parallel 16S rRNA gene sequencing of the retained sludge in the UASB reactor showed the predominant microbial phyla to be Bacteroidetes, Firmicutes, Proteobacteria, WWE1, and Euryarchaeota. Uncultured bacteria belonging to the phylum Bacteroidetes and Phylum WWE1 were predominant in the UASB reactor. This microbial assemblage utilizes the organic compounds contained in natural rubber processing wastewater. In addition, the methane-producing archaea Methanosaeta sp. and Methanolinea sp. were detected.

Finding the Missing Stratospheric Br(sub y): A Global Modeling Study of CHBr3 and CH2Br2

Science.gov (United States)

Liang, Q.; Stolarski, R. S.; Kawa, S. R.; Nielsen, J. E.; Douglass, A. R.; Rodriguez, J. M.; Blake, D. R.; Atlas, E. L.; Ott, L. E.

2010-01-01

Recent in situ and satellite measurements suggest a contribution of 5 pptv to stratospheric inorganic bromine from short-lived bromocarbons. We conduct a modeling study of the two most important short-lived bromocarbons, bromoform (CHBr3) and dibromomethane (CH2Br2), with the Goddard Earth Observing System Chemistry Climate Model (GEOS CCM) to account for this missing stratospheric bromine. We derive a "top-down" emission estimate of CHBr3 and CH2Br2 using airborne measurements in the Pacific and North American troposphere and lower stratosphere obtained during previous NASA aircraft campaigns. Our emission estimate suggests that to reproduce the observed concentrations in the free troposphere, a global oceanic emission of 425 Gg Br yr(exp -1) for CHBr3 and 57 Gg Br yr(exp -l) for CH2Br2 is needed, with 60% of emissions from open ocean and 40% from coastal regions. Although our simple emission scheme assumes no seasonal variations, the model reproduces the observed seasonal variations of the short-lived bromocarbons with high concentrations in winter and low concentrations in summer. This indicates that the seasonality of short-lived bromocarbons is largely due to seasonality in their chemical loss and transport. The inclusion of CHBr3 and CH2Br2 contributes 5 pptv bromine throughout the stratosphere. Both the source gases and inorganic bromine produced from source gas degradation (BrSLS) in the troposphere are transported into the stratosphere, and are equally important. Inorganic bromine accounts for half (2.5 pptv) of the bromine from the inclusion of CHBr3 and CHzBr2 near the tropical tropopause and its contribution rapidly increases to 100% as altitude increases. More than 85% of the wet scavenging of Br(sub y)(sup VSLS) occurs in large-scale precipitation below 500 hPa. Our sensitivity study with wet scavenging in convective updrafts switched off suggests that Br(sub y)(sup SLS) in the stratosphere is not sensitive to convection. Convective scavenging only

In search of new neutrinos and dark matter. The return of fundamental research to BR2

International Nuclear Information System (INIS)

2015-01-01

A consortium of three French, two British, and four Flemish universities and research institutions, including the Belgian Nuclear Research Center SCK-CEN, started in 2014 on the construction of a neutrino experiment in the BR2 reactor. A reactor such as this is an extremely intense source of neutrinos: elementary particles that are generated as a by-product of nuclear beta decay. BR2 is particularly suitable with regard to carrying out this measurement because of the compact core, the high operating capacity, sufficient space for placing a fairly large detector, and the extremely low background radiation. The article discusses recent developments.

Dimensioning the EVITA semi-open loop at BR2 for qualification of full size JHR fuel elements

International Nuclear Information System (INIS)

Gouat, Philippe

2011-01-01

Research highlights: → Research reactor fuel (LEU) qualification as part of the licensing process of the JHR reactor. → Thermal-hydraulic dimensioning process of fuel irradiation installation. → We compare the predicted pressure profile in the installation with in situ measured values. - Abstract: The Jules Horowitz Reactor (JHR) is the next generation research reactor from CEA and which commissioning is foreseen in 2014. Prior to acquiring the exploitation license, the fuel elements have to be qualified for their intended functioning power. The only facility capable to perform this task is the Belgian research reactor BR2, due to its similar thermal-hydraulic parameters. At the moment, one has already tested the fuel plates separately. The preparation of the JHR safety report still needs the test of full size elements. This JHR fuel element is broader and more powerful than a standard BR2 fuel element, and one cannot perform an irradiation by simply interchanging them. However, BR2 has 200 mm channels at its disposal, which can be adapted to give the correct hydraulic diameter. One also needs an additional pump to deliver the necessary cooling flow rate for the higher power. This paper describes the dimensioning of the EVITA semi-open loop, which has been built at BR2 to irradiate full size JHR fuel elements and qualify them for the foreseen exploitation parameters. One explains here the followed methodology to quantify the required additional head for the booster pump and to determine the pressure profile along the circuit and the safety margin on the fuel. This methodology relies only on a priori calculations without any measurement on full size installation subpart as usual before the assembly in controlled zone. The article also explains how the original JHR thermal hydraulic safety calculation scheme was adapted to the BR2 environment. One also compares the measurement results on the fully built installation with our previsions. Our models compare well

Electronic structure of the CsPbBr3/polytriarylamine (PTAA) system

Science.gov (United States)

Endres, James; Kulbak, Michael; Zhao, Lianfeng; Rand, Barry P.; Cahen, David; Hodes, Gary; Kahn, Antoine

2017-01-01

The inorganic lead halide perovskite CsPbBr3 promises similar solar cell efficiency to its hybrid organic-inorganic counterpart CH3NH3PbBr3 but shows greater stability. Here, we exploit this stability for the study of band alignment between perovskites and carrier selective interlayers. Using ultraviolet, X-ray, and inverse photoemission spectroscopies, we measure the ionization energy and electron affinities of CsPbBr3 and the hole transport polymer polytriarylamine (PTAA). We find that undoped PTAA introduces a barrier to hole extraction of 0.2-0.5 eV, due to band bending in the PTAA and/or a dipole at the interface. p-doping the PTAA eliminates this barrier, raising PTAA's highest occupied molecular orbital to 0.2 eV above the CsPbBr3 valence band maximum and improving hole transport. However, IPES reveals the presence of states below the PTAA lowest unoccupied molecular level. If present at the CsPbBr3/PTAA interface, these states may limit the polymer's efficacy at blocking electrons in solar cells with wide band gap materials like CsPbBr3 and CH3NH3PbBr3.

BR3/Vulcain Nuclear Power Station. Construction and Operational Experience

Energy Technology Data Exchange (ETDEWEB)

Storrer, J. [Belgonucleaire, S.A., Brussels (Belgium)

1968-04-15

A full-scale reactor experiment was set out as the main objective of the Vulcain research and development programme agreed in May 1962 between the UKAEA and BelgoNucleaire, manager of ''Syndicat Vulcain''. Vulcain uses variable moderation as the long-term method to control reactivity: the reactor is cooled and moderated by a mixture of heavy and light water, the D{sub 2}O content being stepwise reduced to permit power operation with all control rods completely out of the core. To carry out the Vulcain power experiment it was decided to modify the BR3 nuclear power plant located at Mol, Belgium, which had operated from 1962 to 1964 as a conventional PWR with outputs of 40.9 MW(th) and 11.45 MW(e). The BR3/Vulcain plant was started in December 1966 and since then is running with a load factor around 90%. It is the first time that such a reactor type has been built and operated and the experience gained by its design, construction, commissioning and operation has proven to be most valuable. D{sub 2}O is being used at a pressure (2000 lb/in{sup 2} abs.) never before achieved in a heavy-water reactor and the leak rate from the HP primary systems to the atmosphere has been kept to a negligible value, around 1 to 2 grams/h. Commissioning of the primary plant had been carried out with light water first without fuel, and thereafter with fuel, at which time the water was poisoned with boric acid. The reactor vessel contains experimental devices such as 65 in-pile instrumentation detectors and four hydraulically operated Zircaloy control rods. They required the interposition of a collar between the vessel and its lid. Refuelling is performed under boronated light water, the interchange between the primary water and the H{sub 2}O being carried out by means of a draining and spraying system. The reactor had been operated for two years before its modifications for Vulcain: many lessons have therefore been learned about working on irradiated systems. The BR3/Vulcain core has a

Bromine-rich Zinc Bromides: Zn6Br12(18-crown-6)2×(Br2)5, Zn4Br8(18-crown-6)2×(Br2)3, and Zn6Br12(18-crown-6)2×(Br2)2.

Science.gov (United States)

Hausmann, David; Feldmann, Claus

2016-06-20

The bromine-rich zinc bromides Zn6Br12(18-crown-6)2×(Br2)5 (1), Zn4Br8(18-crown-6)2×(Br2)3 (2), and Zn6Br12(18-crown-6)2×(Br2)2 (3) are prepared by reaction of ZnBr2, 18-crown-6, and elemental bromine in the ionic liquid [MeBu3N][N(Tf)2] (N(Tf)2 = bis(trifluoromethylsulfonyl)amide). Zn6Br12(18-crown-6)2×(Br2)5 (1) is formed instantaneously by the reaction. Even at room temperature, compound 1 releases bromine, which was confirmed by thermogravimetry (TG) and mass spectrometry (MS). The release of Br2 can also be directly followed by the color and density of the title compounds. With controlled conditions (2 weeks, 25 °C, absence of excess Br2) Zn6Br12(18-crown-6)2×(Br2)5 (1) slowly releases bromine with conconcurrent generation of Zn4Br8(18-crown-6)2×(Br2)3 (2) (in ionic liquid) and Zn6Br12(18-crown-6)2×(Br2)2 (3) (in inert oil). All bromine-rich zinc bromides contain voluminous uncharged (e.g., Zn3Br6(18-crown-6), Zn2Br4(18-crown-6)) or ionic (e.g., [Zn2Br3(18-crown-6)](+), [(Zn2Br6)×(Br2)2](2-)) building units with dibromine molecules between the Zn oligomers and partially interconnecting the Zn-containing building units. Due to the structural similarity, the bromine release is possible via crystal-to-crystal transformation with retention of the crystal shape.

Chemical surveillance of commercial fast breeder reactors

International Nuclear Information System (INIS)

Stamm, H.H.; Stade, K.Ch.

1988-01-01

After BN-600 (USSR) and SUPERPHENIX (France) were started succesfully, the international development of LMFBRs is standing at the doorstep of commercial use. For commercial use of LMFBRs cost reductions for construction and operation are highly desirable and necessary. Several nations developing breeder reactors have joined in a common effort in order to reach this aim by standardization and harmonization. On the base of more than 20 years of operation experience of experimental reactors (EBR-II, FFTF, RAPSODIE, DFR, BR-5/BR-10, BOR-60, JOYO, KNK-II) and demonstration plants (PHENIX, PFR, BN-350), possibilities for standardization in chemical surveillance of commercial breeder reactors without any loss of availability, reliability and reactor safety will be discussed in the following chapters. Loop-type reactors will be considered as well as pool-type reactors, although all commercial plants under consideration so far (SUPERPHENIX II, BN-800, BN-1600, CFBR, SNR-2, EFR) include pool-type reactors only. Table 1 gives a comparison of the Na inventories of test reactors, prototype plants and commercial LMFBRs

Substantiation of physical concepts of fast reactors in Russia: experience and prospects

Energy Technology Data Exchange (ETDEWEB)

Alekseev, P.N. [Russian Research Center ' Kurchatov Institute' (RRC KI), 1, Kurchatov Sq., Moscow, 123182 (Russian Federation); Vasiliev, B.A. [Experimental Design Bureau of Machine Building (OKBM) 15, Burnakovskiy Pr., N. Novgorod, 603074 (Russian Federation); Kormilitsyn, M.V. [State Scientific Center of Russian Federation - Research Institute of Atomic Reactors (NIIAR) Dimitrovgrad-10, Ulianovsk Reg., 433510 (Russian Federation); Lopatkin, A.V. [N.A. Dollezhal Research and Development Institute of Power Engineering (NIKIET) 2/8, M. Krasnoselskaya Str., Moscow, 107140 (Russian Federation); Seleznev, E.F. [All-Russian Research Institute for Nuclear Power Plant Operation (VNIIAES) 25, Ferganskaya, Moscow, 109507 (Russian Federation); Khomyakov, Yu.S.; Tsybulia, A.M. [State Scientific Center of the Russian Federation - A. I. Leypunsky Institute for Physics and Power Engineering (SSC RF- IPPE) 1, Bondarenko Sq., Obninsk, Kaluga Reg., 249033 (Russian Federation); Tocheny, L.V. [International Science and Technology Center (ISTC) 32-34 Krasnoproletarskaya Ulitsa, Moscow, 127473 (Russian Federation)

2008-07-01

The fast reactor concept in Russia has accumulated unique experience, since its advent in the 1950's and up to the present, from the creation of the first experimental installation BR-1, experimental reactors BR-5 and BOR-60, the pilot industrial reactors BN-350 in Kazakhstan and up to the BN-600 at Beloyarsk Atomic Power Station. Investigations on the first experimental installations BR-1 and BR-5/-10 proved the propriety of the idea that it is possible to create nuclear reactors that can produce more nuclear fuel than they consume, i.e. the idea of breeding. The architecture of such reactors was also designed, producing a current leader among fast reactors with sodium coolant and oxide uranium-plutonium fuel. Operational experience of BOR-60, BN-350 and, particularly, BN-600 confirmed the engineering and technical feasibility of the concept of fast reactors, the possibility for its realization both for power production and for certain other purposes as well, such as desalinisation of sea water (BN-350) and for radionuclide production (BN-350, BN-600), and it enabled the development and verification of different models, computer methods and codes. The paper presents a review of experience in the creation of plants with fast reactors, scientific research on these installations, principal results, the current status of experimental data analysis, and prospective directions in the development of fast reactors and the corresponding experimental basis in Russia. (authors)

Decommissioning of the BR3 PWR

International Nuclear Information System (INIS)

Massaut, V.; Klein, M.

1998-01-01

The objectives, programme and main achievements of SCK-CEN's decommissioning programme in 1997 are summarised. Particular emphasis is on the BR3 decommissioning project. In 1997, auxiliary equipment and loops were dismantled; concrete antimissile slabs were decontaminated; the radiology of the primary loop was modelled; the quality assurance procedure for dismantling loops and equipment were implemented; a method for the dismantling of the reactor pressure vessel was selected; and contaminated thermal insulation of the primary loop containing asbestos was removed

Role of irradiation reactor mock-ups

International Nuclear Information System (INIS)

Casali, F.; Cerles, J.M.; Debrue, J.

1977-01-01

A survey is given of the utilization of low power facilities in support to irradiation reactor experiments. The BRO2, ISIS and RB3 facilities are described as neutronic mock-ups of the BR2, OSIRIS and ESSOR reactors respectively

RETRAN-02 one-dimensional kinetics model: a review

International Nuclear Information System (INIS)

Gose, G.C.; McClure, J.A.

1986-01-01

RETRAN-02 is a modular code system that has been designed for one-dimensional, transient thermal-hydraulics analysis. In RETRAN-02, core power behavior may be treated using a one-dimensional reactor kinetics model. This model allows the user to investigate the interaction of time- and space-dependent effects in the reactor core on overall system behavior for specific LWR operational transients. The purpose of this paper is to review the recent analysis and development activities related to the one dimensional kinetics model in RETRAN-02

Production of radioisotopes with BR2 facilities

International Nuclear Information System (INIS)

Fallais, C.J.; Morel de Westfaver, A.; Heeren, L.; Baugnet, J.M.; Gandolfo, J.M.; Boeykens, W.

1978-01-01

After a brief account on the isotopes production evolution in the industrialized countries the irradiation devices and the types of standardized capsules used in the BR2 reactor are described as well as the thermal neutron flux. Production of most important radioisotopes like 131 Iodine, 60 Cobalt, 192 Iridium and 99 Molybdenum and their main utilizations (uses)are described. The mean specific activities and the limit of use for different radioisotopes are reported. (A.F.)

Design of Electrical System for Inhibitor Injection Pump’s Motor PAQ 01/02/03 RSG-GAS

International Nuclear Information System (INIS)

Taufiq, M.; Teguh Sulistyo; Kiswanto; Santosa Pujiarta

2008-01-01

In order to control the water quality related to the growth of scale, corrosion and micro-organism in the PA01 BR01 and PA02 BR 02 piping system of secondary cooling system of RSG-GAS, electrical systems for motor of inhibitor injection pump PAQ 01/02/03, including motor control system circuit for inhibitor injection pump PAQ02 AP01, motor control system circuit for NaOCl injection pump PAQ01 AP01, motor control system circuit for inhibitor injection pump PAQ02 AP02 and control system circuit for stir pump RW02 have been designed. Motor control system circuit for pump PAQ02 AP01 which attached at the inhibitor tank will operate when conductivity control CQ01 indicates blow down condition and pump motor PAQ02 AP02 is not operate when level control CL02 indicates minimum level. This design is expected that, NaOCl injection pump PAQ01 AP 01 will operate continuously and inhibitor injection pump PAQ02 AP02 will operate automatically. (author)

Embrittlement and annealing of reactor pressure vessel steels: comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, T.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rossinski, S.T.; Carter, R.G.

1996-07-01

The sister pressure vessels at the BR3 and Rowe Yankee PWR plants were operated at a lower-than-usual temperature (260 degrees Celsius) and their plates were austenitized at higher-than-usual temperature (970 degrees Celsius). A heat tratemement leading to a coarser microstructure than typical for the fine grain plates that are considered in development of USNRC Regulatory guide 1.99. This material displayed outlier behaviour charackterized by a 41J CVN-shift significantly larger than predicted by Regulatory Guide 1.99. Because lower radiation temperature and nickell alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements enbodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: 1) the accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively, 2) the BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, ANCL was trepanned in early 1995, 3) the accelerated irradiations in the Belgian BR2 test reactor of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is shown that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel anneal was neither necessary nor sufficient. Finally, the sensitivity of embrittlement, annealing and post-annealing reembrittlement to irradiation

Embrittlement and annealing of reactor pressure vessel steels: comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe vessel

Energy Technology Data Exchange (ETDEWEB)

Fabry, A.; Chaouadi, T.; Puzzolante, J.L.; Van de Velde, J. [Centre de l``Etude de l``Energie Nucleaire, Mol (Belgium); Biemiller, E.C. [Yankee Atomic Electric Company, Bolton (United States); Rossinski, S.T.; Carter, R.G. [Electric Power Research Institute, Charlotte (United States)

1996-07-01

The sister pressure vessels at the BR3 and Rowe Yankee PWR plants were operated at a lower-than-usual temperature (260 degrees Celsius) and their plates were austenitized at higher-than-usual temperature (970 degrees Celsius). A heat tratemement leading to a coarser microstructure than typical for the fine grain plates that are considered in development of USNRC Regulatory guide 1.99. This material displayed outlier behaviour charackterized by a 41J CVN-shift significantly larger than predicted by Regulatory Guide 1.99. Because lower radiation temperature and nickell alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements enbodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: 1) the accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively, 2) the BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, ANCL was trepanned in early 1995, 3) the accelerated irradiations in the Belgian BR2 test reactor of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is shown that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel anneal was neither necessary nor sufficient. Finally, the sensitivity of embrittlement, annealing and post-annealing reembrittlement to irradiation

Contributions of BrCl, Br2, BrOCl, Br2O, and HOBr to regiospecific bromination rates of anisole and bromoanisoles in aqueous solution.

Science.gov (United States)

Sivey, John D; Bickley, Mark A; Victor, Daniel A

2015-04-21

When bromide-containing waters are chlorinated, conventional wisdom typically assumes HOBr is the only active brominating agent. Several additional and often-overlooked brominating agents (including BrCl, Br2, BrOCl, Br2O) can form in chlorinated waters, albeit at generally lower concentrations than HOBr. The extent to which these additional brominating agents influence bromination rates of disinfection byproduct precursors is, however, poorly understood. Herein, the influence of BrCl, Br2, BrOCl, Br2O, and HOBr toward rates of sequential bromination of anisole was quantified. Conditions affecting bromine speciation (e.g., pH, concentrations of chloride, bromide, and chlorine) were varied, and regiospecific second-order rate constants were calculated for reactions of each brominating agent with anisole, 2-bromoanisole, and 4-bromoanisole. The regioselectivity of anisole bromination changed with pH, consistent with the participation of more than one brominating agent. Under conditions representative of chlorinated drinking water, contributions to bromination rates decreased as BrCl > BrOCl > HOBr > Br2O (Br2 negligible). The second-order rate constant determined for net bromination of anisole by HOBr is up to 3000-times less than reported in previous studies (which assumed HOBr was the only active brominating agent). Accordingly, models that assume HOBr is the only kinetically relevant brominating agent in solutions of free bromine may be insufficient for reactions involving modestly nucleophilic organic compounds.

Simple radiosensitizing of hypoxic tumor tissues by N2O/Br(-) mixture.

Science.gov (United States)

Billik, P

2015-07-01

The radiosensitization model of hypoxic tumor tissues based on the N2O/Br(-) mixture is described. The well-documented radiolysis of water in the presence of N2O and Br(-) ions at a low concentration supports this model. An aqueous solution saturated with N2O gas during the radiolysis generates OH radicals in a large extent. In N2O/Br- media at pHBr2 is formed. Br2 hydrolyzes in an aqueous solution to form a very reactive hypobromous (HOBr) acid. Such process is described by the following chemical reaction: H2O + Br(-) + N2O + ionizing radiation (IR) --> HOBr + OH(-). In vivo formed HOBr as a long-lived product with a high biological activity induces the hypoxic tumor cell damage via many unique mechanisms. A local application or inhalation of an N2O-O2 mixture before or during the radiotherapy to enhance the saturation of tissues with N2O is a key prerequisite. Since the extracellular concentration of Br(-) ions is very low (0.02-0.05 mM), an oral or local application of NaBr should be used to shift the extracellular concentration of Br(-) ions to the mM region. Copyright © 2015 Elsevier Ltd. All rights reserved.

Reactivity effects due to beryllium poisoning of BR2

International Nuclear Information System (INIS)

Kalcheva, S.; Ponsard, B.; Koonen, E.

2004-01-01

This paper illustrates the impact of the poisoning of the beryllium reflector on reactivity variations of the Belgian MTR BR2 in SCK.CEN. Detailed calculations by MCNP-4C of reactivity effects caused by strong neutron absorbers 3 He and 6 Li during reactor operation history are presented. The importance of beryllium poisoning for the accuracy of reactivity predictions is discussed. (authors)

Temperature dependent absorption spectra of Br(-), Br2(•-), and Br3(-) in aqueous solutions.

Science.gov (United States)

Lin, Mingzhang; Archirel, Pierre; Van-Oanh, Nguyen Thi; Muroya, Yusa; Fu, Haiying; Yan, Yu; Nagaishi, Ryuji; Kumagai, Yuta; Katsumura, Yosuke; Mostafavi, Mehran

2011-05-05

The absorption spectra of Br(2)(•-) and Br(3)(-) in aqueous solutions are investigated by pulse radiolysis techniques from room temperature to 380 and 350 °C, respectively. Br(2)(•-) can be observed even in supercritical conditions, showing that this species could be used as a probe in pulse radiolysis at high temperature and even under supercritical conditions. The weak temperature effect on the absorption spectra of Br(2)(•-) and Br(3)(-) is because, in these two systems, the transition occurs between two valence states; for example, for Br(2)(-) we have (2)Σ(u) → (2)Σ(g) transition. These valence transitions involve no diffuse final state. However, the absorption band of Br(-) undergoes an important red shift to longer wavelengths. We performed classical dynamics of hydrated Br(-) system at 20 and 300 °C under pressure of 25 MPa. The radial distribution functions (rdf's) show that the strong temperature increase (from 20 to 300 °C) does not change the radius of the solvent first shell. On the other hand, it shifts dramatically (by 1 Å) the second maximum of the Br-O rdf and introduces much disorder. This shows that the first water shell is strongly bound to the anion whatever the temperature. The first two water shells form a cavity of a roughly spherical shape around the anion. By TDDFT method, we calculated the absorption spectra of hydrated Br(-) at two temperatures and we compared the results with the experimental data.

Fuel characteristics needed for optimal operation of the BR2 reactor

International Nuclear Information System (INIS)

Koonen, E.; Beeckmans, A.; Gubel, P.

1998-01-01

The standard BR2 fuel element contains 400 g 235 U under the form of UAl x with burnable absorbers homogeneously mixed into the fuel meat. The uranium is highly enriched with a density of ∼1.30 g U/cm 3 . This fuel element was developed in the early seventies to satisfy the irradiation conditions required by many experimental programmes: large reactivity available, cycle length, hard neutron spectrum, limited motion of the control rods during the cycle thereby stabilizing the irradiation conditions. Another benefit is the reduction of the fuel consumption by increasing the burnup at discharge. BR2 has recently been restarted after the completion of an important refurbishment programme. Future utilization will again be concentrated on engineering R and D in the field of nuclear fuels, materials and safety, and on radioisotope production. Therefore the required irradiation conditions and the corresponding fuel characteristics remain essentially the same as in the past. (author)

Refurbishment of BR2 (Phase 4 and 5)

International Nuclear Information System (INIS)

Gubel, P.; Dekeyser, J.; Van der Auwera, J.

1998-01-01

The extensive refurbishment of the BR-2 materials testing reactor should allow another 10 to 15 years of continued operation. The refurbishment programme is required in order to comply with modern safety standards, to enhance the reliability of operation, and to compensate for the ageing of the installations of a facility that has reached about 35 years of intensive service. The main objectives and achievements of phase 4 and 5 are described

Studies on the phase diagram of LiBr-SrBr2 system

International Nuclear Information System (INIS)

Mahendran, K.H.; Sujatha, K.; Sridharan, R.; Gnanasekaran, T.

2003-01-01

Binary LiBr-SrBr 2 system was investigated using differential scanning calorimetry (DSC) and the equilibrium phases at different compositions were identified using X-ray diffraction (XRD). This system has a compound LiSr 2 Br 5 , and exhibits a eutectic reaction between this compound and LiBr at 434 deg. C and the eutectic has a composition of 35 mol% SrBr 2 . The compound LiSr 2 Br 5 undergoes peritectic decomposition at 484 deg. C. From the DSC and XRD results, phase diagram of the LiBr-SrBr 2 system is constructed

Artificial intelligence in nuclear reactor operation

International Nuclear Information System (INIS)

Da Ruan; Benitez-Read, J.S.

2005-01-01

Assessment of four real fuzzy control applications at the MIT research reactor in the US, the FUGEN heavy water reactor in Japan, the BR1 research reactor in Belgium, and a TRIGA Mark III reactor in Mexico will be examined through a SWOT analysis (strengths, weakness, opportunities, and threats). Special attention will be paid to the current cooperation between the Belgian Nuclear Research Centre (SCK·CEN) and the Mexican Nuclear Centre (ININ) on AI-based intelligent control for nuclear reactor operation under the partial support of the National Council for Science and Technology of Mexico (CONACYT). (authors)

Neutron diffraction instruments at the BR2 reactor and their use in the study of crystal and magnetic structures

International Nuclear Information System (INIS)

Legrand, E.

1977-01-01

The study of structural properties of condensed matted is frequently performed by means of methods based on X-ray, electron or neutron scattering. In many particular cases, the latter technique offers definite advantages which are mainly based on the following characteristics of neutron-matter interaction: The large penetration depth for neutrons in matter (with the exception of a few elements), which allow the study of large samples and the use of wavelengths from 0.5 to 5A, and even to 10 A; the absence of an atomic form factor; the irregular dependence of the scattering length for the different elements as a function of their atomic number; the large cross section for magnetic scattering; the energy of thermal neutrons which allows the direct measuremtment of the enrgy exchange between the neutrons and the scatterer. Three of the four neutron diffraction instruments for solid state research, installed at the BR2 reactor, are described in detail. (author)

Acclimatization of anaerobic sludge for UASB-reactor start-up

NARCIS (Netherlands)

Zeeuw, de W.J.

1984-01-01

The Upflow Anaerobic Sludge Bed (UASB) reactor represents a high rate anaerobic wastewater treatment system. The majority of the active biomass in the reactor is present in the form of sludge granules which possess excellent settling properties.<br/>If no acclimatized (granular)

Surfactant-promoted reactions of Cl2 and Br2 with Br- in glycerol.

Science.gov (United States)

Faust, Jennifer A; Dempsey, Logan P; Nathanson, Gilbert M

2013-10-17

Gas-liquid scattering experiments are used to explore reactions of gaseous Cl2 and Br2 with a 0.03 M solution of the surfactant tetrahexylammonium bromide (THABr) dissolved in glycerol. At thermal collision energies, 79 ± 2% of incident Cl2 molecules react with Br(-) to form Cl2Br(-) in the interfacial region. This reaction probability is three times greater than the reactivity of Cl2 with 3 M NaBr-glycerol, even though the interfacial Br(-) concentrations are similar in each solution. We attribute the high 79% uptake to the presence of surface THA(+) ions that stabilize the Cl2Br(-) intermediate as it is formed in the charged, hydrophobic pocket created by the hexyl chains. Cl2Br(-) generates the single exchange product BrCl in a 1% yield close to the surface, while the remaining 99% desorbs as the double exchange product Br2 over >0.1 s after diffusing deeply into the bulk. When NaCl is added to the surfactant solution in a 20:1 Cl(-)/Br(-) ratio, the Cl2 reaction probability drops from 79% to 46 ± 1%, indicating that Cl(-) in the interfacial region only partially blocks reaction with Br(-). In parallel, we observe that gaseous Br2 molecules dissolve in 0.03 M THABr for 10(4) times longer than in 3 M NaBr. We attribute this change to formation of stabilizing interfacial and bulk-phase THA(+)Br3(-) ion pairs, in analogy with the capture of Cl2 and formation of THA(+)Cl2Br(-) pairs. The THA(+) ion appears to be a powerful interfacial catalyst for promoting reaction of Cl2 and Br2 with Br(-) and for ferrying the resultant ions into solution.

A comparative ab initio study of Br2*- and Br2 water clusters.

Science.gov (United States)

Pathak, A K; Mukherjee, T; Maity, D K

2006-01-14

The work presents ab initio results on structure and electronic properties of Br2*-.nH2O(n=1-10) and Br2.nH2O(n=1-8) hydrated clusters to study the effects of an excess electron on the microhydration of the halide dimer. A nonlocal density functional, namely, Becke's half-and-half hybrid exchange-correlation functional is found to perform well on the present systems with a split valence 6-31++G(d,p) basis function. Geometry optimizations for all the clusters are carried out with several initial guess structures and without imposing any symmetry restriction. Br2*-.nH2O clusters prefer to have symmetrical double hydrogen-bonding structures. Results on Br2.nH2O(n>or=2) cluster show that the O atom of one H2O is oriented towards one Br atom and the H atom of another H2O is directed to other Br atom making Br2 to exist as Br+-Br- entity in the cluster. The binding and solvation energies are calculated for the Br2*-.nH2O and Br2.nH2O clusters. Calculations of the vibrational frequencies show that the formation of Br2*- and Br2 water clusters induces significant shifts from the normal modes of isolated water. Excited-state calculations are carried out on Br2*-.nH2O clusters following configuration interaction with single electron excitation procedure and UV-VIS absorption profiles are simulated. There is an excellent agreement between the present theoretical UV-VIS spectra of Br2*-.10H2O cluster and the reported transient optical spectra for Br2*- in aqueous solution.

Review of fast reactor operating experience gained in 1998 in Russia. General trends of future fast reactor development

International Nuclear Information System (INIS)

Poplavski, V.M.; Ashurko, Y.M.; Zverev, K.V.; Sarayev, O.M.; Oshkanov, N.N.; Korol'kov, A.S.

1999-01-01

Review of the general state of nuclear power in Russia as for 1998 is given in brief in the paper. Results of operation of BR-10, BOR-60 and BN-600 fast reactors are presented as well as of scientific and technological escort of the BN-350 reactor. The paper outlines the current status and prospects of South-Urals and Beloyarskaya power unit projects with the BN-800 reactors. The main planned development trends on fast reactors are described concerning both new projects and R and D works. (author)

Morphological evolution of copper nanoparticles: Microemulsion reactor system versus batch reactor system

Science.gov (United States)

Xia, Ming; Tang, Zengmin; Kim, Woo-Sik; Yu, Taekyung; Park, Bum Jun

2017-07-01

In the synthesis of nanoparticles, the reaction rate is important to determine the morphology of nanoparticles. We investigated morphology evolution of Cu nanoparticles in this two different reactors, microemulsion reactor and batch reactor. In comparison with the batch reactor system, the enhanced mass and heat transfers in the emulsion system likely led to the relatively short nucleation time and the highly homogeneous environment in the reaction mixture, resulting in suppressing one or two dimensional growth of the nanoparticles. We believe that this work can offer a good model system to quantitatively understand the crystal growth mechanism that depends strongly on the local monomer concentration, the efficiency of heat transfer, and the relative contribution of the counter ions (Br- and Cl-) as capping agents.

Status of fast reactor activities in Russia

International Nuclear Information System (INIS)

Poplavski, V.M.; Ashurko, Yu.M.; Zverev, K.V.

1998-01-01

This paper outlines state-of-the-art of the Russian nuclear power as of 1997 and its prospects for the nearest future. Results of the BR-10, BOR-60 and BN-600 reactors operation are described, as well as activity of the Russian institutions on scientific and technological support of the BN-350 reactor. Analysis of current status of the BN-800 reactor South-Urals NPP and Beloyarskaya NPP designs is given in brief, as well as prospects of their construction and possible ways of fast reactor technology improvement. Studies on fast reactors now under way in Russia are described. (author)

Die Interhalogenkationen [Br2F5]+ und [Br3F8].

Science.gov (United States)

Ivlev, Sergei; Karttunen, Antti; Buchner, Magnus; Conrad, Matthias; Kraus, Florian

2018-05-02

Wir berichten über die Synthese und Charakterisierung der bislang einzigen Polyhalogenkationen, in denen verbrückende Fluoratome vorliegen. Das [Br2F5]+-Kation enthält eine symmetrische [F2Br-µ-F-BrF2]-Brücke, das [Br3F8]+-Kation enthält unsymmetrische µ-F-Brücken. Die Fluoronium-Ionen wurden in Form ihrer [SbF6]--Salze erhalten und Raman-, und 19F-NMR-spektroskopisch, sowie durch Röntgenbeugung am Einkristall untersucht. Quantenchemische Rechnungen, sowohl für die isolierten Kationen in der Gasphase, als auch für die Festkörper selbst, wurden durchgeführt. Populationsanalysen zeigen, dass die µ-F-Atome die am stärksten negativ partialgeladenen Atome der Kationen sind. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The determination of thermal neutron cross section of 81Br

International Nuclear Information System (INIS)

Kovacs, Luciana; Zamboni, Cibele B.; Dalaqua Junior, Leonardo

2009-01-01

In this investigation several standard materials were used to determine the thermal neutron cross section of 81 Br. This nuclear parameter is an important data to perform several quantitative investigations, mainly in medical area. In other to confirm and to reduce the uncertainty, a new measurement was preformed using thermal neutron at IEA-R1 nuclear reactor of IPEN/CNEN-SP. The result obtained is compatible with the tabulated value and present small uncertainly. (author)

Matrix isolation and computational study of isodifluorodibromomethane (F2CBr-Br): a route to Br2 formation in CF2Br2 photolysis.

Science.gov (United States)

George, Lisa; Kalume, Aimable; El-Khoury, Patrick Z; Tarnovsky, Alexander; Reid, Scott A

2010-02-28

The photolysis products of dibromodifluoromethane (CF(2)Br(2)) were characterized by matrix isolation infrared and UV/Visible spectroscopy, supported by ab initio calculations. Photolysis at wavelengths of 240 and 266 nm of CF(2)Br(2):Ar samples (approximately 1:5000) held at approximately 5 K yielded iso-CF(2)Br(2) (F(2)CBrBr), a weakly bound isomer of CF(2)Br(2), which is characterized here for the first time. The observed infrared and UV/Visible absorptions of iso-CF(2)Br(2) are in excellent agreement with computational predictions at the B3LYP/aug-cc-pVTZ level. Single point energy calculations at the CCSD(T)/aug-cc-pVDZ level on the B3LYP optimized geometries suggest that the isoform is a minimum on the CF(2)Br(2) potential energy surface, lying some 55 kcal/mol above the CF(2)Br(2) ground state. The energies of various stationary points on the CF(2)Br(2) potential energy surface were characterized computationally; taken with our experimental results, these show that iso-CF(2)Br(2) is an intermediate in the Br+CF(2)Br-->CF(2)+Br(2) reaction. The photochemistry of the isoform was also investigated; excitation into the intense 359 nm absorption band resulted in isomerization to CF(2)Br(2). Our results are discussed in view of the rich literature on the gas-phase photochemistry of CF(2)Br(2), particularly with respect to the existence of a roaming atom pathway leading to molecular products.

The decommissioning of the BR3 steam generator

International Nuclear Information System (INIS)

Denissen, L.

2006-01-01

A steam generator is a crucial component in a PWR (Pressurized Water Reactor). It is the crossing between the primary, contaminated, circuit and the secondary water-steam circuit. The heat from the primary reactor coolant loop is transferred to the secondary side in thousands of small tubes. Due to several problems in the material of those tubes, like SCC (Stress Corrosion Cracking), insufficient control in water chemistry, which can be the cause of tube leakage, more and more steam generators are replaced today. Only in Belgium, already 17 of them are replaced. The old 300 ton heavy SGs are stored at the 2 nuclear power plants of Doel and Tihange . While it was foreseen in the BR3 strategy to dismantle the steam generator (only 30 ton), we took the opportunity to search for a complete package in the decommissioning of a steam generator. The complete management consists of a decontamination of the primary side followed by the complete dismantling. The first step, the decontamination with MEDOC (water box + tube bundle) has already been achieved in 2002. It has led to an important DF (Decontamination Factor) between 100 and 1000 and an important dose rate reduction. This hard chemical decontamination process has been described earlier in the scientific report 2002 (The BR3 steam generator decontamination with the MEDOC process - M. Ponnet). The second step, the complete dismantling of the SG has been executed in 2005. With the BR3 SG, the main goal was to dismantle it in a safe way and to free release a maximum of material. We've used two cutting tools to perform the job: A HPWJC (High Pressure Water Jet Cutting) tool in combination with a hydraulic robot and a water cooled diamond cable. The last technique was done in close collaboration with the external company Husqvarna. It was important to have an idea of the performance, the efficiency of the cable and the quantity and the type of secondary waste

Understanding overpressure in the FAA aerosol can test by C3H2F3Br (2-BTP).

Science.gov (United States)

Linteris, Gregory Thomas; Babushok, Valeri Ivan; Pagliaro, John Leonard; Burgess, Donald Raymond; Manion, Jeffrey Alan; Takahashi, Fumiaki; Katta, Viswanath Reddy; Baker, Patrick Thomas

2016-05-01

Thermodynamic equilibrium calculations, as well as perfectly-stirred reactor (PSR) simulations with detailed reaction kinetics, are performed for a potential halon replacement, C 3 H 2 F 3 Br (2-BTP, C 3 H 2 F 3 Br, 2-Bromo-3,3,3-trifluoropropene), to understand the reasons for the unexpected enhanced combustion rather than suppression in a mandated FAA test. The high pressure rise with added agent is shown to depend on the amount of agent, and is well-predicted by an equilibrium model corresponding to stoichiometric reaction of fuel, oxygen, and agent. A kinetic model for the reaction of C 3 H 2 F 3 Br in hydrocarbon-air flames has been applied to understand differences in the chemical suppression behavior of C 3 H 2 F 3 Br vs. CF 3 Br in the FAA test. Stirred-reactor simulations predict that in the conditions of the FAA test, the inhibition effectiveness of C 3 H 2 F 3 Br at high agent loadings is relatively insensitive to the overall stoichiometry (for fuel-lean conditions), and the marginal inhibitory effect of the agent is greatly reduced, so that the mixture remains flammable over a wide range of conditions. Most important, the flammability of the agent-air mixtures themselves (when compressively preheated), can support low-strain flames which are much more difficult to extinguish than the easy-to extinguish, high-strain primary fireball from the impulsively released fuel mixture. Hence, the exothermic reaction of halogenated hydrocarbons in air should be considered in other situations with strong ignition sources and low strain flows, especially at preheated conditions.

Core electron binding energy shifts of AlBr3 and Al2Br6 vapor

International Nuclear Information System (INIS)

Mueller, Astrid M.; Plenge, Juergen; Leone, Stephen R.; Canton, Sophie E.; Rude, Bruce S.; Bozek, John D.

2006-01-01

The Al 2p and Br 3d inner-shell photoelectron spectra of aluminum tribromide monomer and dimer vapor were measured at 90 and 95 eV photon energy, respectively, to determine the core electron binding energies of the atoms in the two molecular species. While AlBr 3 has three identical Br atoms, Al 2 Br 6 exhibits four terminal and two bridging Br atoms. The species are identified by their distinct valence photoelectron spectra. Comparison of the observed Al 2p 1/2 and Al 2p 3/2 electron binding energies of AlBr 3 with those of Al 2 Br 6 shows that there is a chemical shift of (0.15 ± 0.03) eV to lower energy in the dimer. In Al 2 Br 6 , an assignment is proposed in which the Br 3d 3/2 and Br 3d 5/2 binding energies of terminal Br atoms are (1.18 ± 0.03) eV lower than those of bridging Br atoms. This assignment assumes that both types of Br atoms have similar cross-sections for ionization. With this result, the Br 3d 3/2 and Br 3d 5/2 binding energies of Br atoms in AlBr 3 are (0.81 ± 0.03) eV lower than those of bridging Br atoms of the dimer but (0.37 ± 0.03) eV higher than those of terminal Br atoms of the dimer. The obtained chemical shifts are considered in terms of the binding relations and electron density distributions in both molecules. Chemical shifts that are larger than a few hundred millielectron volts, as observed in the Al 2 Br 6 /AlBr 3 system, offer potential to study the dissociation dynamics of the dimer in a femtosecond visible or ultraviolet-pump/XUV-probe experiment

The BR2 refurbishment programme: achievements and two years operation feedback

International Nuclear Information System (INIS)

Gubel, P.; Dekeyser, J.; Koonen, E.; Van der Auwera, J.

1999-01-01

The BR2 reactor was shutdown end of June 1995 for an extensive refurbishment after more than 30 years utilization. The beryllium matrix needed to be replaced and the aluminium vessel inspected for an envisaged 15 year life extension. Other aspects of the refurbishment programme aimed at the reliability and availability of the installations, safety of operation and compliance with modern safety standards. The reactor was started again in' April '97 and operated only for three cycles in 1997. These first irradiation cycles were intended as a demonstration of the safety and reliability of all components and systems after refurbishment. Also during the extended shutdowns non-critical refurbishment tasks were allowed to be continued and finalized. At the request of the Safety Authorities, some modifications and studies are still in progress without perturbation of the reactor operation. (author)

Corrosion of type 316 stainless steel in molten LiF-LiCl-LiBr

International Nuclear Information System (INIS)

Tortorelli, P.F.; DeVan, J.H.; Keiser, J.R.

1981-01-01

The properties of LiF-LiCl-LiBr salt make it attractive as a solvent for extracting tritium from a fusion reactor lithium blanket. Consequently, the corrosion of type 316 stainless steel by flowing (about 15 mm/s) LiF-LiCl-LiBr at a maximum temperature of 535 0 C was studied to determine whether compatibility with the structural material would be limiting in such a system. The corrosion rate was found to be low ( 0 C (approximately that of type 316 stainless steel exposed to lithium flowing at a similar velocity). At the proposed operating temperature (less than or equal to approx. 535 0 C), however, it appears that type 316 stainless steel has acceptable compatibility with the tritium-processing salt LiF-LiCl-LiBr for use with a lithium blanket

Matrix isolation and computational study of isodifluorodibromomethane (F2CBr-Br): A route to Br2 formation in CF2Br2 photolysis

International Nuclear Information System (INIS)

George, Lisa; Kalume, Aimable; Reid, Scott A.; El-Khoury, Patrick Z.; Tarnovsky, Alexander

2010-01-01

The photolysis products of dibromodifluoromethane (CF 2 Br 2 ) were characterized by matrix isolation infrared and UV/Visible spectroscopy, supported by ab initio calculations. Photolysis at wavelengths of 240 and 266 nm of CF 2 Br 2 :Ar samples (∼1:5000) held at ∼5 K yielded iso-CF 2 Br 2 (F 2 CBrBr), a weakly bound isomer of CF 2 Br 2 , which is characterized here for the first time. The observed infrared and UV/Visible absorptions of iso-CF 2 Br 2 are in excellent agreement with computational predictions at the B3LYP/aug-cc-pVTZ level. Single point energy calculations at the CCSD(T)/aug-cc-pVDZ level on the B3LYP optimized geometries suggest that the isoform is a minimum on the CF 2 Br 2 potential energy surface, lying some 55 kcal/mol above the CF 2 Br 2 ground state. The energies of various stationary points on the CF 2 Br 2 potential energy surface were characterized computationally; taken with our experimental results, these show that iso-CF 2 Br 2 is an intermediate in the Br+CF 2 Br→CF 2 +Br 2 reaction. The photochemistry of the isoform was also investigated; excitation into the intense 359 nm absorption band resulted in isomerization to CF 2 Br 2 . Our results are discussed in view of the rich literature on the gas-phase photochemistry of CF 2 Br 2 , particularly with respect to the existence of a roaming atom pathway leading to molecular products.

Computer simulation of the structure of liquid metal halides RbBr, CuCl, CuBr, CuI, and AgBr

International Nuclear Information System (INIS)

Belashchenko, D.K.; Ostrovskij, O.I.

2003-01-01

The computerized models of the RbBr, AgBr, CuCl, CuBr and CuI liquid ion systems of 498 ions dimension are simulated at the temperatures of 753-960 K on the basis of the known diffraction data through the BELION algorithm. Good agreement of diffraction and model partial pair correlation functions (PPCF), excluding the PPCF first peaks heights, is obtained in all the cases. The simulation is carried out by the varied ion charges (the atomization energy values, close to the real ones, are obtained by ion charges ±1.00 for the RbBr, ±1.15 for AgBr, ±1.20 for CuCl, ±1.48 for CuBr and ±1.367 for CuI). The noncoulomb contributions in the interparticle potentials are calculated [ru

Rate constant for the reaction SO + BrO yields SO2 + Br

Science.gov (United States)

Brunning, J.; Stief, L.

1986-01-01

The rate of the radical-radical reaction SO + BrO yields SO2 + Br has been determined at 298 K in a discharge flow system near 1 torr pressure with detection of SO and BrO via collision-free sampling mass spectrometry. The rate constant was determined using two different methods: measuring the decay of SO radicals in the presence of an excess of BrO and measuring the decay of BrO radicals in excess SO. The results from the two methods are in reasonable agreement and the simple mean of the two values gives the recommended rate constant at 298 K, k = (5.7 + or - 2.0) x 10 to the -11th cu cm/s. This represents the first determination of this rate constant and it is consistent with a previously derived lower limit based on SO2 formation. Comparison is made with other radical-radical reactions involving SO or BrO. The reaction SO + BrO yields SO2 + Br is of interest for models of the upper atmosphere of the earth and provides a potential coupling between atmospheric sulfur and bromine chemistry.

Dye adsorbates BrPDI, BrGly, and BrAsp on anatase TiO2(001) for dye-sensitized solar cell applications

Science.gov (United States)

Çakır, D.; Gülseren, O.; Mete, E.; Ellialtıoǧlu, Ş.

2009-07-01

Using the first-principles plane-wave pseudopotential method within density functional theory, we systematically investigated the interaction of perylenediimide (PDI)-based dye compounds (BrPDI, BrGly, and BrAsp) with both unreconstructed (UR) and reconstructed (RC) anatase TiO2(001) surfaces. All dye molecules form strong chemical bonds with surface in the most favorable adsorption structures. In UR-BrGly, RC-BrGly, and RC-BrAsp cases, we have observed that highest occupied molecular orbital and lowest unoccupied molecular orbital levels of molecules appear within band gap and conduction-band region, respectively. Moreover, we have obtained a gap narrowing upon adsorption of BrPDI on the RC surface. Because of the reduction in effective band gap of surface-dye system and possibly achieving the visible-light activity, these results are valuable for photovoltaic and photocatalytic applications. We have also considered the effects of hydration of surface to the binding of BrPDI. It has been found that the binding energy drops significantly for the completely hydrated surfaces.

Photodissociation of C3H5Br and C4H7Br at 234 nm

International Nuclear Information System (INIS)

Kim, Hyun Kook; Paul, Dababrata; Hong, Ki Ryong; Cho, Ha Na; Kim, Tae Kyu; Lee, Kyoung Seok

2012-01-01

The photodissociation dynamics of cyclopropyl bromide (C-3H 5 Br) and cyclobutyl bromide (C 4 H 7 Br) at 234 nm was investigated. A two-dimensional photofragment ion-imaging technique coupled with a [2+1] resonance enhanced multiphoton ionization scheme was utilized to obtain speed and angular distributions of the nascent Br( 2 P 3/2 ) and Br*( 2 P 1/2 ) atoms. The recoil anisotropies for the Br and Br* channels were measured to be βBr = 0.92 ± 0.03 and βBr* = 1.52 ± 0.04 for C 3 H 5 Br and βBr = 1.10 ± 0.03 and βBr* = 1.49 ± 0.05 for C 4 H 7 Br. The relative quantum yield for Br was found to be ΦBr = 0.13 ± 0.03 and for C 3 H 5 Br and C 4 H 7 Br, respectively. The soft radical limit of the impulsive model adequately modeled the related energy partitioning. The nonadiabatic transition probability from the 3A' and 4A' potential energy surfaces was estimated and discussed

The states of 73Se populated by the beta decay of 73Br

International Nuclear Information System (INIS)

Heiguchi, K.; Mitarai, S.; Min, B.J.; Kuroyanagi, T.

1987-01-01

Decay of mass-separated samples of the nuclide 73 Br have been investigated by means of an on-line isotope separator in the Tandem Accelerator Laboratory of Kyushu University. Twenty eight γ-rays were assigned to the decay of 73 Br. The half-life was measured to be 3.4±0.2 min. The decay scheme of 73 Br was constructed on the basis of γ-ray energies, intensities of γ-rays and conversion electrons, and relations of γγ-, βγ- and γ(ce)-coincidences. Spins and parities of the ten levels of 73 Se were assigned or limited according to log ft values, conversion coefficients and branching ratios of the transitions. Systematical trends in the level schemes of N=39 isotones 69 Zn, 71 Ge, 73 Se, 75 Kr and 77 Sr are discussed. (orig.)

Status of fast reactor activities in the USSR

International Nuclear Information System (INIS)

Troyanov, M.F.; Rinejskij, A.A.

1990-01-01

Four fast reactors are in operation in the USSR now: BR-10, BOR-60, BN-350 and BN-600. Load factor of BN-600 reactor was in 1989 about 76%. On the basis of operational experience of running reactors design of more powerful commercial size BN-800 power reactor has been completed recently and construction work has started at two sites. The BN-1600 reactor is considered to be the prototype of future commercial reactors. In 1990, it was decided to extend its design approach with the aim to find some additional solutions to provide higher safety and better economics. (author). Figs and tabs

Understanding overpressure in the FAA aerosol can test by C3H2F3Br (2-BTP)✩

Science.gov (United States)

Linteris, Gregory Thomas; Babushok, Valeri Ivan; Pagliaro, John Leonard; Burgess, Donald Raymond; Manion, Jeffrey Alan; Takahashi, Fumiaki; Katta, Viswanath Reddy; Baker, Patrick Thomas

2018-01-01

Thermodynamic equilibrium calculations, as well as perfectly-stirred reactor (PSR) simulations with detailed reaction kinetics, are performed for a potential halon replacement, C3H2F3Br (2-BTP, C3H2F3Br, 2-Bromo-3,3,3-trifluoropropene), to understand the reasons for the unexpected enhanced combustion rather than suppression in a mandated FAA test. The high pressure rise with added agent is shown to depend on the amount of agent, and is well-predicted by an equilibrium model corresponding to stoichiometric reaction of fuel, oxygen, and agent. A kinetic model for the reaction of C3H2F3Br in hydrocarbon-air flames has been applied to understand differences in the chemical suppression behavior of C3H2F3Br vs. CF3Br in the FAA test. Stirred-reactor simulations predict that in the conditions of the FAA test, the inhibition effectiveness of C3H2F3Br at high agent loadings is relatively insensitive to the overall stoichiometry (for fuel-lean conditions), and the marginal inhibitory effect of the agent is greatly reduced, so that the mixture remains flammable over a wide range of conditions. Most important, the flammability of the agent-air mixtures themselves (when compressively preheated), can support low-strain flames which are much more difficult to extinguish than the easy-to extinguish, high-strain primary fireball from the impulsively released fuel mixture. Hence, the exothermic reaction of halogenated hydrocarbons in air should be considered in other situations with strong ignition sources and low strain flows, especially at preheated conditions. PMID:29628525

CaBr2 hydrolysis for HBr production using a direct sparging contactor

International Nuclear Information System (INIS)

Doctor, R.D.; Yang, J.; Panchal, Ch.B.; Lottes, St.A.; Lyczkowski, R.W.

2010-01-01

We investigated a novel, continuous hybrid cycle for hydrogen production employing both heat and electricity. Calcium bromide (CaBr 2 ) hydrolysis, which is endothermic, generates hydrogen bromide (HBr), and this is electrolysed to produce hydrogen. CaBr 2 hydrolysis at 1050 K is endothermic with a 181.5 KJ/mol heat of reaction and the free energy change is positive at 99.6 kJ/mol. What makes this hydrolysis reaction attractive is both its rate and the fact that well over half the thermodynamic requirements for water-splitting free energy of ΔG T = 285.8 KJ/mol are supplied at this stage using heat rather than electricity. These experiments provide support for a second order hydrolysis reaction in CaBr 2 forming a complex involving CaBr 2 and CaO and the system appears to be: 3CaBr 2 + H 2 O → (CaBr 2 ) 2 .CaO + 2HBr. This reaction is highly endothermic and the complex also includes some water of hydration. COMSOL TM multi-physics modelling of sparging steam into a calcium bromide melt guided the design of an experiment using a mullite tube (ID 70 mm) capable of holding 0.3-0.5 kg (1.5-2.5 10 -3 kmol) CaBr 2 forming a melt with a maximum 0.08 m depth. Half of the experiments employed packings. Sparging steam at a steam rate of 0.02-0.04 mol/mol of CaBr 2 per minute into this molten bath promptly yielded HBr in a stable operation that converted up to 19 mol% of the calcium bromide. The kinetic constant derived from the experimental data was kinetic constant was 2.17 10 -12 kmol s -1 m -2 MPa -1 for the hydrolysis reaction. (authors)

$\\beta$-delayed neutrons from oriented $^{137,139}$I and $^{87,89}$Br nuclei

CERN Multimedia

We propose a world-first measurement of the angular distribution of $\\beta$‐delayed n and $\\gamma$-radiation from oriented $^{137, 139}$I and $^{87,89}$Br nuclei, polarised at low temperature at the NICOLE facility. $\\beta$­-delayed neutron emission is an increasingly important decay mechanism as the drip line is approached and its detailed understanding is essential to phenomena as fundamental as the r‐process and practical as the safe operation of nuclear power reactors. The experiments offer sensitive tests of theoretical input concerning the allowed and first­‐forbidden $\\beta$‐decay strength, the spin-density of neutron emitting states and the partial wave barrier penetration as a function of nuclear deformation. In $^{137}$I and $^{87}$Br the decay feeds predominantly the ground state of the daughters $^{136}$Xe and $^{86}$Kr whereas in $^{139}$I and $^{89}$Br we will explore the use of n-$\\gamma$- coincidence to study neutron transitions to the first and second excited states in the daughters...

Multiple Gamma-Ray Detection Capability of a CeBr3 Detector for Gamma Spectroscopy

Directory of Open Access Journals (Sweden)

A. A. Naqvi

2017-01-01

Full Text Available The newly developed cerium tribromide (CeBr3 detector has reduced intrinsic gamma-ray activity with gamma energy restricted to 1400–2200 keV energy range. This narrower region of background gamma rays allows the CeBr3 detector to detect more than one gamma ray to analyze the gamma-ray spectrum. Use of multiple gamma-ray intensities in elemental analysis instead of a single one improves the accuracy of the estimated results. Multigamma-ray detection capability of a cylindrical 75 mm × 75 mm (diameter × height CeBr3 detector has been tested by analyzing the chlorine concentration in water samples using eight chlorine prompt gamma rays over 517 to 8578 keV energies utilizing a D-D portable neutron generator-based PGNAA setup and measuring the corresponding minimum detection limit (MDC of chlorine. The measured MDC of chlorine for gamma rays with 517–8578 keV energies varies from 0.07 ± 0.02 wt% to 0.80 ± 0.24. The best value of MDC was measured to be 0.07 ± 0.02 wt% for 788 keV gamma rays. The experimental results are in good agreement with Monte Carlo calculations. The study has shown excellent detection capabilities of the CeBr3 detector for eight prompt gamma rays over 517–8578 keV energy range without significant background interference.

$^{80}$Br $^{80}$Br-a new electron-gamma PAC probe

CERN Document Server

Correia, J G; Araújo, J P; Marques, J G; Soares, J C; Melo, A A

2001-01-01

Conversion electron-gamma PAC measurements of the 49-37 keV cascade in /sup 80/Br through the intermediate 2/sup -/ state with T/sub 1/2 /=7.4 ns were performed with a system of two magnetic lens spectrometers and two BaF/sub 2/ scintillation detectors. The parent /sup 80m/Br activity with a halflife of 4.4 hrs was implanted into Ni, Zn and graphite at the ISOLDE separator at CERN. The observed interaction frequency in the nickel matrix is in good agreement with the known value of the hyperfine field for Br in Ni and the magnetic moment of the 2/sup -/ state. From the measured quadrupole interaction in Zn and graphite the electric field gradients at Br were obtained. (7 refs).

Preparation of 80Br or 82Br-biomolecules via excitation labelling methods

International Nuclear Information System (INIS)

Wong, S.; Ache, H.J.

1975-01-01

The direct decay-induced 82 Br (or 80 Br) labelling by exposing the solid substrate molecules, such as deoxyuridine, L-tyrosine, guanosine, deoxycytidine, phenylalanine, and acetic acid, to gaseous CF 3 82 /sup m/Br (or CF 3 80 /sup m/Br) was studied. The radiochemical yields of the brominated products are relatively small and range from 1 percent in the case of bromo deoxyuridine to 11 percent for bromoacetic acid. The modification of this technique by adding Cl 2 gas to the reaction mixture improves the yields in several cases drastically (up to 80 percent for bromo-guanosine and bromo-L-tyrosine). Similar improvement can be achieved by exposing crystalline KBrO 3 for some time to CF 3 82 /sup m/Br (or CF 3 80 /sup m/Br) and dissolving subsequently the KBrO 3 in an acidic solution of the substrate. (auth)

RA reactor reactivity changes before refurbishment - Task 3.08/02; Zadatak 3.08/02 - Promene reaktivnosti reaktora RA do remonta

Energy Technology Data Exchange (ETDEWEB)

Dobrosavljevic, N; Strugar, P; Stamenkovic, S [Institute of Nuclear Sciences Boris Kidric, Reaktor RA, Vinca, Beograd (Serbia and Montenegro)

1963-12-15

From the the end of 1959, when the RA reactor started operation until January 1963 reactor was operated with the initial fuel batch of 56 fuel channels. After 310 MWd 68 fuel channels were added to the reactor core, and after further 357 MWd the core was filled up to the maximum of 88 fuel channels. Basic reactor parameters were systematically measured during two years of operation. This report covers the measurements concerned directly with the reactor operation: calibration of the control rods and their reactivity worths during operation, determining the total built-in reactivity excess and its change during burnup, determination of reactivity dependence on the temperature, xenon effect in the core.

Synthesis and structural characterization of inorganic luminescent materials of Cs2NaErBr6 and Cs2NaHoBr6

International Nuclear Information System (INIS)

Poblete, V.H; Fack, G

2003-01-01

The synthesis and structural characterization is described of two luminescent materials, with technological [1] and spectroscopic [2] interest, whose crystallographic charts have not been published in the literature. The synthesis of both systems: Cs 2 NaErBr 6 and CS 2 NaHoBr 6 , was done using solid state reactions in a controlled environment. The thermal analyses DTA/TGA, applied with a temperature gradient of 10 o C/min., established crystallization ranges of 490,4 o C to 545,4 o C, for the elpasolite CS 2 NaHoBr 6 and 501 o C to 556 o C, for the structure CS 2 NaErBr 6 .. The heat vacuum treatments were carried out at 505 o C and 526 o C respectively, obtaining optimum crystallization. The structural characterization was performed with powdered X-ray diffraction (XRD). The range between 12 o and 80 o (2θ), was analyzed for 3352 points, measured steps of 0.02 o (2θ using the Rietveld profile refining program. The following crystallographic parameters were established: a 0 = 11,279(1), and 11,293(4) Angstroms, for the two structures analyzed, respectively. The relationship R exp wp in both cases is highly accurate for the 32 test lines that were analyzed. The structures present cubic closed packing Cs 1+ 3 Cl 1- , with Ho 3+ and Er 3+ atoms, filling the octahedral holes. The test data obtained will be very useful for completing the mass of experimental data needed to develop the design engineering, with specific applications for luminescent devices (au)

Visible Light Driven Nanosecond Bromide Oxidation by a Ru Complex with Subsequent Br-Br Bond Formation.

Science.gov (United States)

Li, Guocan; Ward, William M; Meyer, Gerald J

2015-07-08

Visible light excitation of [Ru(deeb)(bpz)2](2+) (deeb = 4,4'-diethylester-2,2'-bipyridine; bpz = 2,2'-bipyrazine), in Br(-) acetone solutions, led to the formation of Br-Br bonds in the form of dibromide, Br2(•-). This light reactivity stores ∼1.65 eV of free energy for milliseconds. Combined (1)H NMR, UV-vis and photoluminescence measurements revealed two distinct mechanisms. The first involves diffusional quenching of the excited state by Br(-) with a rate constant of (8.1 ± 0.1) × 10(10) M(-1) s(-1). At high Br(-) concentrations, an inner-sphere pathway is dominant that involves the association of Br(-), most likely with the 3,3'-H atoms of a bpz ligand, before electron transfer from Br(-) to the excited state, ket = (2.5 ± 0.3) × 10(7) s(-1). In both mechanisms, the direct photoproduct Br(•) subsequently reacts with Br(-) to yield dibromide, Br(•) + Br(-) → Br2(•-). Under pseudo-first-order conditions, this occurs with a rate constant of (1.1 ± 0.4) × 10(10) M(-1) s(-1) that was, within experimental error, the same as that measured when Br(•) were generated with ultraviolet light. Application of Marcus theory to the sensitized reaction provided an estimate of the Br(•) formal reduction potential E(Br(•)/Br(-)) = 1.22 V vs SCE in acetone, which is about 460 mV less positive than the accepted value in H2O. The results demonstrate that Br(-) oxidation by molecular excited states can be rapid and useful for solar energy conversion.

RESONANCE CARS IN BR2 MOLECULES AND BR-ATOMS

NARCIS (Netherlands)

Aben, I.; Levelt, P.; Ubachs, W.M.G.; Hogervorst, W.

1991-01-01

Resonance-enhanced CARS processes were studied in molecular bromine. On the basis of the known spectroscopic constants of the two electronic states involved, the features in the spectra could be identified. CARS signals from Br-atoms produced from dissociation of Br2 were obtained by tuning (omega-1

Design of fuel failure detection system for multipurpose reactor GA. Siwabessy

International Nuclear Information System (INIS)

Sujalmo Saiful; Kuntoro Iman; Sato, Mitsugu; Isshiki, Masahiko.

1992-01-01

A fuel failure detection system (FFDS) has been designed for the Reactor GA. Siwabessy. The FFDS is aimed to detect fuel failure by observing delayed neutron released by fission products such as N-17, I-137, Br-87 and Br-88 in the primary cooling system. The delayed neutrons will be detected by using four neutron detectors, type BF-3, which are located inside a Sampling Tank. The detector location has been determined and the location is associated with the transit time from the reactor core outlet to the Sampling Tank, which is approximately 60 seconds. The neutron detection efficiency was calculated by using a computer code named MORSE. The FFDS has the capability to detect as quickly as possible, even a small failure of a fuel element occurring in the reactor core. Therefore the presence of FFDS in a reactor must be considered, in order to prevent further progress if the fuel failure occurs. (author)

Photodissociation of 1,2-dibromoethylene at 248 nm: Br2 molecular elimination probed by cavity ring-down absorption spectroscopy.

Science.gov (United States)

Chang, Yuan-Pin; Lee, Ping-Chen; Lin, King-Chuen; Huang, C H; Sun, B J; Chang, A H H

2008-06-02

The Br2 elimination channel is probed for 1,2-C2H2Br2 in the B(3)Pi(+)ou-X(1)Sigma(+)g transition upon irradiation at 248 nm by using cavity ring-down absorption spectroscopy (CRDS). The nascent vibrational population ratio of Br2(v=1)/Br2(v=0) is obtained to be 0.7+/-0.2, thus indicating that the Br2 fragment is produced in hot vibrational states. The obtained Br2 products are anticipated to result primarily from photodissociation of the ground-state cis isomer via four-center elimination or from cis/trans isomers via three-center elimination, each mechanism involving a transition state that has a Br-Br distance much larger than that of ground state Br2. According to ab initio potential energy calculations, the pathways that lead to Br2 elimination may proceed either through the electronic ground state by internal conversion or through the triplet state by intersystem crossing. Temperature-dependence measurements are examined, thereby supporting the pathway that involves internal conversion--which was excluded previously by using product translational spectroscopy (PTS). The quantum yield for the Br2 elimination reaction is determined to be 0.120.1, being substantially contributed by the ground-state Br2 product. The discrepancy of this value from that (of 0.2) obtained by PTS may rise from the lack of measurements in probing the triplet-state Br2 product.

Molecular elimination of Br2 in photodissociation of CH2BrC(O)Br at 248 nm using cavity ring-down absorption spectroscopy.

Science.gov (United States)

Fan, He; Tsai, Po-Yu; Lin, King-Chuen; Lin, Cheng-Wei; Yan, Chi-Yu; Yang, Shu-Wei; Chang, A H H

2012-12-07

The primary elimination channel of bromine molecule in one-photon dissociation of CH(2)BrC(O)Br at 248 nm is investigated using cavity ring-down absorption spectroscopy. By means of spectral simulation, the ratio of nascent vibrational population in v = 0, 1, and 2 levels is evaluated to be 1:(0.5 ± 0.1):(0.2 ± 0.1), corresponding to a Boltzmann vibrational temperature of 581 ± 45 K. The quantum yield of the ground state Br(2) elimination reaction is determined to be 0.24 ± 0.08. With the aid of ab initio potential energy calculations, the obtained Br(2) fragments are anticipated to dissociate on the electronic ground state, yielding vibrationally hot Br(2) products. The temperature-dependence measurements support the proposed pathway via internal conversion. For comparison, the Br(2) yields are obtained analogously from CH(3)CHBrC(O)Br and (CH(3))(2)CBrC(O)Br to be 0.03 and 0.06, respectively. The trend of Br(2) yields among the three compounds is consistent with the branching ratio evaluation by Rice-Ramsperger-Kassel-Marcus method. However, the latter result for each molecule is smaller by an order of magnitude than the yield findings. A non-statistical pathway so-called roaming process might be an alternative to the Br(2) production, and its contribution might account for the underestimate of the branching ratio calculations.

Hybridization of Single Nanocrystals of Cs4PbBr6 and CsPbBr3.

Science.gov (United States)

Weerd, Chris de; Lin, Junhao; Gomez, Leyre; Fujiwara, Yasufumi; Suenaga, Kazutomo; Gregorkiewicz, Tom

2017-09-07

Nanocrystals of all-inorganic cesium lead halide perovskites (CsPbX 3 , X = Cl, Br, I) feature high absorption and efficient narrow-band emission which renders them promising for future generation of photovoltaic and optoelectronic devices. Colloidal ensembles of these nanocrystals can be conveniently prepared by chemical synthesis. However, in the case of CsPbBr 3 , its synthesis can also yield nanocrystals of Cs 4 PbBr 6 and the properties of the two are easily confused. Here, we investigate in detail the optical characteristics of simultaneously synthesized green-emitting CsPbBr 3 and insulating Cs 4 PbBr 6 nanocrystals. We demonstrate that, in this case, the two materials inevitably hybridize, forming nanoparticles with a spherical shape. The actual amount of these Cs 4 PbBr 6 nanocrystals and nanohybrids increases for synthesis at lower temperatures, i.e., the condition typically used for the development of perovskite CsPbBr 3 nanocrystals with smaller sizes. We use state-of-the-art electron energy loss spectroscopy to characterize nanoparticles at the single object level. This method allows distinguishing between optical characteristics of a pure Cs 4 PbBr 6 and CsPbBr 3 nanocrystal and their nanohybrid. In this way, we resolve some of the recent misconceptions concerning possible visible absorption and emission of Cs 4 PbBr 6 . Our method provides detailed structural characterization, and combined with modeling, we conclusively identify the nanospheres as CsPbBr 3 /Cs 4 PbBr 6 hybrids. We show that the two phases are independent of each other's presence and merge symbiotically. Herein, the optical characteristics of the parent materials are preserved, allowing for an increased absorption in the UV due to Cs 4 PbBr 6 , accompanied by the distinctive efficient green emission resulting from CsPbBr 3 .

Reactor Physics Training

International Nuclear Information System (INIS)

Baeten, P.

2007-01-01

University courses in nuclear reactor physics at the universities consist of a theoretical description of the physics and technology of nuclear reactors. In order to demonstrate the basic concepts in reactor physics, training exercises in nuclear reactor installations are also desirable. Since the number of reactor facilities is however strongly decreasing in Europe, it becomes difficult to offer to students a means for demonstrating the basic concepts in reactor physics by performing training exercises in nuclear installations. Universities do not generally possess the capabilities for performing training exercises. Therefore, SCK-CEN offers universities the possibility to perform (on a commercial basis) training exercises at its infrastructure consisting of two research reactors (BR1 and VENUS). Besides the organisation of training exercises in the framework of university courses, SCK-CEN also organizes theoretical courses in reactor physics for the education and training of nuclear reactor operators. It is indeed a very important subject to guarantee the safe operation of present and future nuclear reactors. In this framework, an understanding of the fundamental principles of nuclear reactor physics is also necessary for reactor operators. Therefore, the organisation of a basic Nuclear reactor physics course at the level of reactor operators in the initial and continuous training of reactor operators has proven to be indispensable. In most countries, such training also results from the direct request from the safety authorities to assure the high level of competence of the staff in nuclear reactors. The objectives this activity are: (1) to provide training and education activities in reactor physics for university students and (2) to organise courses in nuclear reactor physics for reactor operators

BR-100 spent fuel shipping cask development

International Nuclear Information System (INIS)

McGuinn, E.J.; Childress, P.C.

1990-01-01

Continued public acceptance of commercial nuclear power is contingent to a large degree on the US Department of Energy (DOE) establishing an integrated waste management system for spent nuclear fuel. As part of the from-reactor transportation segment of this system, the B ampersand W Fuel Company (BWFC) is under contract to the DOE to develop a spent-fuel cask that is compatible with both rail and barge modes of transportation. Innovative design approaches were the keys to achieving a cask design that maximizes payload capacity and cask performance. The result is the BR-100, a 100-ton rail/barge cask with a capacity of 21 PWR or 52 BWR ten-year cooled, intact fuel assemblies. 3 figs

The TbBr3–LiBr binary system: Experimental thermodynamic investigation and assessment of phase diagram

International Nuclear Information System (INIS)

Rycerz, L.; Gong, W.; Gaune-Escard, M.

2013-01-01

Highlights: ► DSC measurements for the (LiBr + TbBr 3 ) system. ► congruently Li3TbBr 6 and incongruently melting Li5TbBr 8 compounds. ► Thermodynamic description of the liquid phase in the (LiBr + TbBr 3 ) system. ► Assessment with a two-sublattice ionic solution model. - Abstract: DSC was used to study the phase equilibrium in the TbBr 3 –LiBr binary system. The results obtained provided a basis for constructing the phase diagram of this system. It exhibits two compounds: Li 5 TbBr 8 , which decomposes in the solid state at 611 K, and Li 3 TbBr 6 , which melts congruently at 785 K with the related enthalpy 59.1 kJ·mol −1 . The binary LiBr–TbBr 3 system was then optimized using the available experimental information on phase diagram and thermodynamic properties. A two-sub-lattice ionic solution model (Li + ) P :(Br − , TbBr 6 −3 , TbBr 3 ) Q was adopted to describe the liquid phase. The present assessment of the binary LiBr–TbBr 3 system was in good agreement with the corresponding experimental data and confirmed their consistency.

$^{80m}$Br/$^{80}$Br a new electron-$\\gamma$ - PAC Probe

CERN Document Server

Correia, J G; Araújo, J P; Marques, J G; Soares, J C; Melo, A A

2001-01-01

Conversion electron-$\\gamma$ PAC measurements of the 49 keV - 37 keV cascade in $^{80}$Br through the intermediate 2$^{-}$ state with T$_{1/2}$=7.4 ns were performed with a system of two magnetic lens spectrometers and two BaF$_{2}$ scintillation detectors. The parent $^{80m}$Br activity with half-life of 4.4 hrs was implanted into Ni, Zn and graphite at the ISOLDE separator at CERN. The observed interaction frequency in the nickel matrix is in good agreement with the known value of the hyperfine field for Br in Ni and the magnetic moment of the 2$^{-}$ state. From the measured quadrupole interaction in Zn and graphite the electric field gradients at Br were obtained.

Elimination of nonspecific radioactivity from [76Br]bromide in PET study with [76Br]bromodeoxyuridine

International Nuclear Information System (INIS)

Li Lu; Bergstroem, Mats; Fasth, Karl-Johan; Wu Feng; Eriksson, Barbro; Laangstroem, Bengt

1999-01-01

[ 76 Br]Bromodeoxyuridine ([ 76 Br]BrdU) might allow a determination of proliferation in vivo using positron emission tomography (PET), but only with consideration of organ nonspecific radioactivity constituted by [ 76 Br]bromide. A first study assessed the potential of diuretics to eliminate [ 76 Br]bromide. [ 76 Br]Bromide was injected in the vein of rats and different diuretic combinations were given. Urine was collected and radioactivity measured. Torasemide plus sodium chloride gave better 76 Br elimination than the other diuretics. In a second experiment, rats were given [ 76 Br]BrdU. After the radioactivity injection, the rats of the treatment group were given torasemide plus NaCl. At 44 h after the radioactivity injection, the radioactivity concentration and the fraction incorporated into DNA were measured in different organs. Using diuretics, the elimination of [ 76 Br]bromide was increased. The radioactivity decreased 30-50% in most of the organs but the highest radioactivity uptake was found in the organs with more active DNA synthesis. This method may facilitate the use of [ 76 Br]BrdU as a tracer for DNA synthesis using PET

Direct Vapor Growth of Perovskite CsPbBr3 Nanoplate Electroluminescence Devices.

Science.gov (United States)

Hu, Xuelu; Zhou, Hong; Jiang, Zhenyu; Wang, Xiao; Yuan, Shuangping; Lan, Jianyue; Fu, Yongping; Zhang, Xuehong; Zheng, Weihao; Wang, Xiaoxia; Zhu, Xiaoli; Liao, Lei; Xu, Gengzhao; Jin, Song; Pan, Anlian

2017-10-24

Metal halide perovskite nanostructures hold great promises as nanoscale light sources for integrated photonics due to their excellent optoelectronic properties. However, it remains a great challenge to fabricate halide perovskite nanodevices using traditional lithographic methods because the halide perovskites can be dissolved in polar solvents that are required in the traditional device fabrication process. Herein, we report single CsPbBr 3 nanoplate electroluminescence (EL) devices fabricated by directly growing CsPbBr 3 nanoplates on prepatterned indium tin oxide (ITO) electrodes via a vapor-phase deposition. Bright EL occurs in the region near the negatively biased contact, with a turn-on voltage of ∼3 V, a narrow full width at half-maximum of 22 nm, and an external quantum efficiency of ∼0.2%. Moreover, through scanning photocurrent microscopy and surface electrostatic potential measurements, we found that the formation of ITO/p-type CsPbBr 3 Schottky barriers with highly efficient carrier injection is essential in realizing the EL. The formation of the ITO/p-type CsPbBr 3 Schottky diode is also confirmed by the corresponding transistor characteristics. The achievement of EL nanodevices enabled by directly grown perovskite nanostructures could find applications in on-chip integrated photonics circuits and systems.

Fast reactors in Russia: State of the art and trends of development

International Nuclear Information System (INIS)

Poplavsky, V.M.; Ashurko, Yu.M.; Zverev, K.V.; Oshkanov, N.N.; Korol'kov, A.S.; Filin, A.I.

2002-01-01

This status report contains the following: facts on nuclear power in Russia from 2001-2002; plans for further development of nuclear power; state of the art on operation of fast reactors in 2002, namely BN-600, experimental reactors BOR-60 and BR-10; construction of NPP BN-800; participation in activities on BN-350 reactor decommissioning; description of trends of design studies in the field of fast reactors and accelerator driven systems

Improved production of Br atoms near zero speed by photodissociating laser aligned Br2 molecules.

Science.gov (United States)

Deng, L Z; Yin, J P

2014-10-28

We theoretically investigated the improvement on the production rate of the decelerated bromine (Br) atoms near zero speed by photodissociating laser aligned Br2 precursors. Adiabatic alignment of Br2 precursors exposed to long laser pulses with duration on the order of nanoseconds was investigated by solving the time-dependent Schrödinger equation. The dynamical fragmentation of adiabatically aligned Br2 precursors was simulated and velocity distribution of the Br atoms produced was analyzed. Our study shows that the larger the degree of the precursor alignment, ⟨cos(2) θ⟩, the higher the production rate of the decelerated Br atoms near zero speed. For Br2 molecules with an initial rotational temperature of ~1 K, a ⟨cos(2) θ⟩ value of ~0.88 can result in an improvement factor of over ~20 on the production rate of the decelerated Br atoms near zero speed, requiring a laser intensity of only ~1 × 10(12) W/cm(2) for alignment.

$\\beta$-delayed neutrons from oriented $^{137,139}$I and $^{87,89}$Br nuclei

CERN Document Server

Grzywacz, Robert; Stone, Nicholas; Köster, Ulli; Singh, Barlaj; Bingham, Carrol; Gaulard, S; Kolos, Karolina; Madurga, Miguel; Nikolov, J; Otsubo, T; Roccia, S; Veskovic, Miroslav; Walker, Phil; Walters, William

2013-01-01

We propose a world-­‐first measurement of the angular distribution of $\\beta$-­‐delayed n and $\\gamma$- radiation from oriented $^{137, 139}$I and $^{87,89}$Br nuclei, polarised at low temperature at the NICOLE facility. $\\beta$-­‐delayed neutron emission is an increasingly important decay mechanism as the drip line is approached and its detailed understanding is essential to phenomena as fundamental as the r‐process and practical as the safe operation of nuclear power reactors. The experiments offer sensitive tests of theoretical input concerning the allowed and first-­‐forbidden $\\beta$‐decay strength, the spin-­‐density of neutron emitting states and the partial wave barrier penetration as a function of nuclear deformation. In $^{137}$I and $^{87}$Br the decay feeds predominantly the ground state of the daughters $^{136}$Xe and $^{86}$Kr whereas in $^{139}$I and $^{89}$Br we will explore the use of n-$\\gamma$- coincidence to study neutron transitions to the first and second excited state...

MTR fuel testing in BR2

International Nuclear Information System (INIS)

Jacquet, P.; Verwimp, A.; Wirix, S.

2000-01-01

New fuel design for MTR 's requires to be qualified under representative conditions, that is geometry, neutron spectrum, heat flux and thermo hydraulic conditions. An irradiation device for fuel plates has been designed to derive the maximum benefit from the BR2 irradiation capacities. The fuel plates can be easily extracted from their support during a shutdown to undergo additional tests. One of these tests is the measurement of the thickness changes along the fuel plate. To that purpose, a facility in the reactor water pool has been designed to measure the fuel swelling with an accuracy of 5 μm using inductive probes. At SCK-CEN, the full range of destructive and non-destructive PIE can be performed, including γ-scanning, wet sipping, surface examination and other methods. (author)

Multi-physics design and analyses of long life reactors for lunar outposts

Science.gov (United States)

Schriener, Timothy M.

event of a launch abort accident. Increasing the amount of fuel in the reactor core, and hence its operational life, would be possible by launching the reactor unfueled and fueling it on the Moon. Such a reactor would, thus, not be subject to launch criticality safety requirements. However, loading the reactor with fuel on the Moon presents a challenge, requiring special designs of the core and the fuel elements, which lend themselves to fueling on the lunar surface. This research investigates examples of both a solid core reactor that would be fueled at launch as well as an advanced concept which could be fueled on the Moon. Increasing the operational life of a reactor fueled at launch is exercised for the NaK-78 cooled Sectored Compact Reactor (SCoRe). A multi-physics design and analyses methodology is developed which iteratively couples together detailed Monte Carlo neutronics simulations with 3-D Computational Fluid Dynamics (CFD) and thermal-hydraulics analyses. Using this methodology the operational life of this compact, fast spectrum reactor is increased by reconfiguring the core geometry to reduce neutron leakage and parasitic absorption, for the same amount of HEU in the core, and meeting launch safety requirements. The multi-physics analyses determine the impacts of the various design changes on the reactor's neutronics and thermal-hydraulics performance. The option of increasing the operational life of a reactor by loading it on the Moon is exercised for the Pellet Bed Reactor (PeBR). The PeBR uses spherical fuel pellets and is cooled by He-Xe gas, allowing the reactor core to be loaded with fuel pellets and charged with working fluid on the lunar surface. The performed neutronics analyses ensure the PeBR design achieves a long operational life, and develops safe launch canister designs to transport the spherical fuel pellets to the lunar surface. The research also investigates loading the PeBR core with fuel pellets on the Moon using a transient Discrete

Synthesis and structural characterization of luminescent inorganic materials of the type CS2NaErBr6 and CS2NaHoBr6

International Nuclear Information System (INIS)

Poblete, V.H.; Fack, G.

2001-01-01

The synthesis and structural characterization is described of two luminescent materials, with technological [1] and spectroscopic [2] interest, whose crystallographic charts have not been published in the literature. The synthesis of both systems: Cs 2 NaErBr 6 and CS 2 NaHoBr 6 , was done using solid state reactions in a controlled environment. The thermal analyses DTA/TGA, applied with a temperature gradient of 10 o C/min., established crystallization ranges of 490,4 o C to 545,4 o C, for the elpasolite CS 2 NaHoBr 6 and 501 o C to 556 o C, for the structure CS 2 NaErBr 6 .. The heat vacuum treatments were carried out at 505 o C and 526 o C respectively, obtaining optimum crystallization. The structural characterization was performed with powdered X-ray diffraction (XRD). The range between 12 o and 80 o (2θ), was analyzed for 3352 points, measured steps of 0.02 o (2θ using the Rietveld profile refining program. The following crystallographic parameters were established: a 0 = 11,279(1), and 11,293(4) Angstroms, for the two structures analyzed, respectively. The relationship R exp wp in both cases is highly accurate for the 32 test lines that were analyzed. The structures present cubic closed packing Cs 1+ 3 Cl 1- , with Ho 3+ and Er 3+ atoms, filling the octahedral holes. The test data obtained will be very useful for completing the mass of experimental data needed to develop the design engineering, with specific applications for luminescent devices

A Study of Inverted-Type Perovskite Solar Cells with Various Composition Ratios of (FAPbI31−x(MAPbBr3x

Directory of Open Access Journals (Sweden)

Lung-Chien Chen

2016-10-01

Full Text Available This work presents mixed (FAPbI31−x(MAPbBr3x perovskite films with various composition ratios, x (x = 0–1, which are formed using the spin coating method. The structural, optical, and electronic behaviors of the mixed (FAPbI31−x(MAPbBr3x perovskite films are discussed. A device with structure glass/indium tin oxide (ITO/poly(3,4-ethylenedioxythiophene polystyrene sulfonate (PEDOT:PSS/mixed perovskite/C60/BCP/Ag was fabricated. The mixed perovskite film was an active light-harvesting layer. PEDOT:PSS was a hole transporting layer between the ITO and perovskite. Both C60 and bathocuproine (BCP were electron transporting layers. MAPbBr3 was added to FAPbI3 with a composition ratio of x = 0.2, stabilizing the perovskite phase, which exhibited a uniform and dense morphology. The optimal device exhibited band matching with C60, resulting in a low series resistance (Rsh and a high fill factor (FF. Therefore, the device with composition (FAPbI31−x(MAPbBr3x and x = 0.2 exhibited outstanding performance.

All-Ambient Processed Binary CsPbBr3-CsPb2Br5 Perovskites with Synergistic Enhancement for High-Efficiency Cs-Pb-Br-Based Solar Cells.

Science.gov (United States)

Zhang, Xisheng; Jin, Zhiwen; Zhang, Jingru; Bai, Dongliang; Bian, Hui; Wang, Kang; Sun, Jie; Wang, Qian; Liu, Shengzhong Frank

2018-02-28

All-inorganic CsPbBr 3 perovskite solar cells display outstanding stability toward moisture, light soaking, and thermal stressing, demonstrating great potential in tandem solar cells and toward commercialization. Unfortunately, it is still challenging to prepare high-performance CsPbBr 3 films at moderate temperatures. Herein, a uniform, compact CsPbBr 3 film was fabricated using its quantum dot (QD)-based ink precursor. The film was then treated using thiocyanate ethyl acetate (EA) solution in all-ambient conditions to produce a superior CsPbBr 3 -CsPb 2 Br 5 composite film with a larger grain size and minimal defects. The achievement was attributed to the surface dissolution and recrystallization of the existing SCN - and EA. More specifically, the SCN - ions were first absorbed on the Pb atoms, leading to the dissolution and stripping of Cs + and Br - ions from the CsPbBr 3 QDs. On the other hand, the EA solution enhances the diffusion dynamics of surface atoms and the surfactant species. It is found that a small amount of CsPb 2 Br 5 in the composite film gives the best surface passivation, while the Br-rich surface decreases Br vacancies (V Br ) for a prolonged carrier lifetime. As a result, the fabricated device gives a higher solar cell efficiency of 6.81% with an outstanding long-term stability.

New measurement of BR(D→ρμν)BR(D→Kμν) branching ratio

Science.gov (United States)

FOCUS Collaboration; Link, J. M.; Yager, P. M.; Anjos, J. C.; Bediaga, I.; Castromonte, C.; Machado, A. A.; Magnin, J.; Massafferri, A.; de Miranda, J. M.; Pepe, I. M.; Polycarpo, E.; Dos Reis, A. C.; Carrillo, S.; Casimiro, E.; Cuautle, E.; Sánchez-Hernández, A.; Uribe, C.; Vá, F.; Agostino, L.; Cinquini, L.; Cumalat, J. P.; O'Reilly, B.; Segoni, I.; Stenson, K.; Butler, J. N.; Cheung, H. W. K.; Chiodini, G.; Gaines, I.; Garbincius, P. H.; Garren, L. A.; Gottschalk, E.; Kasper, P. H.; Kreymer, A. E.; Kutschke, R.; Wang, M.; Benussi, L.; Bertani, M.; Bianco, S.; Fabbri, F. L.; Pacetti, S.; Zallo, A.; Reyes, M.; Cawlfield, C.; Kim, D. Y.; Rahimi, A.; Wiss, J.; Gardner, R.; Kryemadhi, A.; Chung, Y. S.; Kang, J. S.; Ko, B. R.; Kwak, J. W.; Lee, K. B.; Cho, K.; Park, H.; Alimonti, G.; Barberis, S.; Boschini, M.; Cerutti, A.; D'Angelo, P.; Dicorato, M.; Dini, P.; Edera, L.; Erba, S.; Inzani, P.; Leveraro, F.; Malvezzi, S.; Menasce, D.; Mezzadri, M.; Moroni, L.; Pedrini, D.; Pontoglio, C.; Prelz, F.; Rovere, M.; Sala, S.; Davenport, T. F.; Arena, V.; Boca, G.; Bonomi, G.; Gianini, G.; Liguori, G.; Lopes Pegna, D.; Merlo, M. M.; Pantea, D.; Ratti, S. P.; Riccardi, C.; Vitulo, P.; Gö, C.; Otalora, J.; Hernandez, H.; Lopez, A. M.; Mendez, H.; Paris, A.; Quinones, J.; Ramirez, J. E.; Zhang, Y.; Wilson, J. R.; Handler, T.; Mitchell, R.; Engh, D.; Hosack, M.; Johns, W. E.; Luiggi, E.; Moore, J. E.; Nehring, M.; Sheldon, P. D.; Vaandering, E. W.; Webster, M.; Sheaff, M.

2006-06-01

Using data collected by the FOCUS experiment at Fermilab, we present a new measurement of the charm semileptonic branching ratio BR(D→ρμν)BR(D→Kμν). From a sample of 320±44 and 11372±161D→ρμν and D→Kπμν events respectively, we find BR(D→ρμν)BR(D→Kμν)=0.041±0.006 (stat)±0.004 (syst).

Exploring Polaronic, Excitonic Structures and Luminescence in Cs4PbBr6/CsPbBr3.

Science.gov (United States)

Kang, Byungkyun; Biswas, Koushik

2018-02-15

Among the important family of halide perovskites, one particular case of all-inorganic, 0-D Cs 4 PbBr 6 and 3-D CsPbBr 3 -based nanostructures and thin films is witnessing intense activity due to ultrafast luminescence with high quantum yield. To understand their emissive behavior, we use hybrid density functional calculations to first compare the ground-state electronic structure of the two prospective compounds. The dispersive band edges of CsPbBr 3 do not support self-trapped carriers, which agrees with reports of weak exciton binding energy and high photocurrent. The larger gap 0-D material Cs 4 PbBr 6 , however, reveals polaronic and excitonic features. We show that those lattice-coupled carriers are likely responsible for observed ultraviolet emission around ∼375 nm, reported in bulk Cs 4 PbBr 6 and Cs 4 PbBr 6 /CsPbBr 3 composites. Ionization potential calculations and estimates of type-I band alignment support the notion of quantum confinement leading to fast, green emission from CsPbBr 3 nanostructures embedded in Cs 4 PbBr 6 .

Yrityksen brändin uudistaminen

OpenAIRE

Saarimaa, Petri

2015-01-01

Brändin rakentaminen on tänä päivänä tärkeä osa yrityksen näkyvyyden ja kilpailukyvyn edistämisessä. Huolellisesti rakennetulla brändillä ja hyvällä markkinoinnilla yritys voi erottua kilpailijoistaan positiivisesti. Tie menestyvään brändiin on kuitenkin pitkä prosessi. Toimeksiantajana opinnäytetyössä toimi rakennusyritys Rakennus Vuoriot Oy. Opinnäytetyön tavoitteena oli toteuttaa yritykselle brändin uudistaminen luomalla kokonaan uusi perusta ja rakennusosat olemassa olevalle brändille...

Qualification program for JHR fuel elements: Irradiation of the first JHR test assembly in the BR2-Evita loop

International Nuclear Information System (INIS)

Anselmet, M.-C.; Lemoine, P.; Koonen, E.; Benoit, P.; Gouat, P.; Claes, W.; Geens, F.; Miras, G.; Brisson, S.

2010-01-01

An experimental program has been designed by CEA to qualify the behaviour of the JHR fuel under conditions representative of the reactor operating ones. This program uses the SCK.CEN facilities, irradiating JHR lead test elements in the BR2 reactor, inside its central channel which has been particularly arranged for this objective (Evita loop). As a first step in the program, a two cycle irradiation (4 weeks by cycle) started mid-July 2009 and ended mid-November (EVITA-1). After a cooling phase, this first JHR lead test element will be submitted to post-irradiation examination. The second JHR test element began its irradiation in the first quarter of 2010; its unloading is planned before the end of 2010, after 5 cycles in the BR2 reactor. The results of these two experiments are expected as input information for the Safety Authority Report. This paper presents the qualification program with the objectives assigned to each phase (irradiation, examination). A first interpretation of the irradiation data for the first element is presented, so as the information available on the progress of the following phases of the programme. (author)

Radiation induced currents in mineral-insulated cables and in pick-up coils: model calculations and experimental verification in the BR1 reactor

Science.gov (United States)

Vermeeren, Ludo; Leysen, Willem; Brichard, Benoit

2018-01-01

Mineral-insulated (MI) cables and Low-Temperature Co-fired Ceramic (LTCC) magnetic pick-up coils are intended to be installed in various position in ITER. The severe ITER nuclear radiation field is expected to lead to induced currents that could perturb diagnostic measurements. In order to assess this problem and to find mitigation strategies models were developed for the calculation of neutron-and gamma-induced currents in MI cables and in LTCC coils. The models are based on calculations with the MCNPX code, combined with a dedicated model for the drift of electrons stopped in the insulator. The gamma induced currents can be easily calculated with a single coupled photon-electron MCNPX calculation. The prompt neutron induced currents requires only a single coupled neutron-photon-electron MCNPX run. The various delayed neutron contributions require a careful analysis of all possibly relevant neutron-induced reaction paths and a combination of different types of MCNPX calculations. The models were applied for a specific twin-core copper MI cable, for one quad-core copper cable and for silver conductor LTCC coils (one with silver ground plates in order to reduce the currents and one without such silver ground plates). Calculations were performed for irradiation conditions (neutron and gamma spectra and fluxes) in relevant positions in ITER and in the Y3 irradiation channel of the BR1 reactor at SCK•CEN, in which an irradiation test of these four test devices was carried out afterwards. We will present the basic elements of the models and show the results of all relevant partial currents (gamma and neutron induced, prompt and various delayed currents) in BR1-Y3 conditions. Experimental data will be shown and analysed in terms of the respective contributions. The tests were performed at reactor powers of 350 kW and 1 MW, leading to thermal neutron fluxes of 1E11 n/cm2s and 3E11 n/cm2s, respectively. The corresponding total radiation induced currents are ranging from

Chanel-brändin nuorentaminen Suomessa

OpenAIRE

Auvinen, Elina

2017-01-01

Tämän opinnäytetyön tavoitteena oli kartoittaa Chanel-kosmetiikkabrändin imagoa ja asiakaskuntaa Suomessa sekä luoda saatujen tulosten pohjalta kehitysehdotuksia Chanel-brändin markkinointiin Suomessa brändin nuorentamisen näkökulmasta. Työn toimeksiantaja oli Chanel-brändin jakelija Oy Transmeri Ab. Teoriataustassa käsiteltiin laajasti erilaisia brändin nuorentamiseen liittyviä aihepiirejä; bränditeoriaa, brändien uudistamista, luksusbrändien erityispiirteitä sekä niiden asiakkaita, digitaal...

Validation of MCNP and ORIGEN-S 3-D computational model for reactivity predictions during BR2 operation

International Nuclear Information System (INIS)

Kalcheva, S.; Koonen, E.; Ponsard, B.

2005-01-01

The Belgian Material Test Reactor (MTR) BR2 is strongly heterogeneous high flux engineering test reactor at SCK-CEN (Centre d'Etude de l'energie Nucleaire) in Mol at a thermal power 60 to 100 MW. It deploys highly enriched uranium, water cooled concentric plate fuel elements, positioned inside a beryllium reflector with complex hyperboloid arrangement of test holes. The objective of this paper is the validation of a MCNP and ORIGEN-S 3D model for reactivity predictions of the entire BR2 core during reactor operation. We employ the Monte Carlo code MCNP-4C for evaluating the effective multiplication factor k eff and 3D space dependent specific power distribution. The 1D code ORIGEN-S is used for calculation of isotopic fuel depletion versus burn up and preparation of a database (DB) with depleted fuel compositions. The approach taken is to evaluate the 3D power distribution at each time step and along with DB to evaluate the 3D isotopic fuel depletion at the next step and to deduce the corresponding shim rods positions of the reactor operation. The capabilities of the both codes are fully exploited without constraints on the number of involved isotope depletion chains or increase of the computational time. The reactor has a complex operation, with important shutdowns between cycles, and its reactivity is strongly influenced by poisons, mainly 3 He and 6 Li from the beryllium reflector, and burnable absorbers 149 Sm and 10 B in the fresh UAlx fuel. Our computational predictions for the shim rods position at various restarts are within 0.5$ (β eff =0.0072). (author)

Photoresponse of CsPbBr3 and Cs4PbBr6 Perovskite Single Crystals.

Science.gov (United States)

Cha, Ji-Hyun; Han, Jae Hoon; Yin, Wenping; Park, Cheolwoo; Park, Yongmin; Ahn, Tae Kyu; Cho, Jeong Ho; Jung, Duk-Young

2017-02-02

High-quality and millimeter-sized perovskite single crystals of CsPbBr 3 and Cs 4 PbBr 6 were prepared in organic solvents and studied for correlation between photocurrent generation and photoluminescence (PL) emission. The CsPbBr 3 crystals, which have a 3D perovskite structure, showed a highly sensitive photoresponse and poor PL signal. In contrast, Cs 4 PbBr 6 crystals, which have a 0D perovskite structure, exhibited more than 1 order of magnitude higher PL intensity than CsPbBr 3 , which generated an ultralow photoresponse under illumination. Their contrasting optoelectrical characteristics were attributed to different exciton binding energies, induced by coordination geometry of the [PbBr 6 ] 4- octahedron sublattices. This work correlated the local structures of lead in the primitive perovskite and its derivatives to PL spectra as well as photoconductivity.

In situ Spectroscopy of Solid-State Chemical Reaction in PbBr2-Deposited CsBr Crystals

Science.gov (United States)

Kondo, Shin-ichi; Matsunaga, Toshihiro; Saito, Tadaaki; Asada, Hiroshi

2003-09-01

It is possible to measure the fundamental optical absorption spectra of CsPbBr3 and Cs4PbBr6, whose stability is predicted by the study of phase diagram in the binary system CsBr-PbBr2, by means of in situ optical absorption and reflection spectroscopy of thermally induced solid-state chemical reaction in PbBr2-deposited CsBr crystals. On heavy annealing of the crystals, the Pb2+ ions are uniformly dispersed in the crystal matrix. The present experiment provides a novel method for measuring intrinsic optical absorption of ternary metal halides and also for in situ monitoring of doping metal halide crystal with impurities (metal ions or halogen ions).

Electric Energy Consumption of Multi Purpose Reactor GA. Siwabessy During Reactor Operation

International Nuclear Information System (INIS)

Koes Indrakoesoema

2012-01-01

Electrical power supply of Reactor Center Multi Purpose obtained from PT PLN to 3030 kVA power contracts. Distribution to existing loads in PRSG divided into 3 (three) lines, each of which is supplied through a transformer BHT01, BHT02 and BHT03, each transformer have capacity of 1600 kVA. During reactor operation, only 2 lines that serve loads, each line serve 2 primary pump motor and 2 secondary pump motor. Electrical power for 24 hours for measurement BHT01, the average is 288 kW, for BHT02 is 641 kW and BHT03 is 466 kW. The energy absorbed by each transformer for 24 hours of measurement, for BHT01 is 6.44 MWh, BHT02 absorb 14.8 MWh and BHT03 absorb 10.9 MWh. (author)

Status of fast reactor activities in the Russian Federation

Energy Technology Data Exchange (ETDEWEB)

Troyanov, M F; Rinejsjij, A A [Institute of Physics and Power Engineering, Obninsk (Russian Federation)

1992-07-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication.

Status of fast reactor activities in the Russian Federation

International Nuclear Information System (INIS)

Troyanov, M.F.; Rinejsjij, A.A.

1992-01-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication

Final report on in-reactor creep-fatigue deformation behaviour of a CuCrZr alloy: COFAT 1

DEFF Research Database (Denmark)

Singh, Bachu Narain; Tähtinen, S.; Moilanen, P.

CrZr(HT1) alloy exposed concurrently to flux of neutrons and creep-fatigue cyclic loading directly in a fission reactor. Special experimental facilities were designed and fabricated for this purpose. A number of in-reactor creep-fatigue experiments were successfully carried out in the BR-2 reactor at Mol...

Tunable CsPbBr3/Cs4PbBr6 phase transformation and their optical spectroscopic properties.

Science.gov (United States)

Chen, Xiao; Chen, Daqin; Li, Junni; Fang, Gaoliang; Sheng, Hongchao; Zhong, Jiasong

2018-04-24

As a novel type of promising materials, metal halide perovskites are a rising star in the field of optoelectronics. On this basis, a new frontier of zero-dimensional perovskite-related Cs4PbBr6 with bright green emission and high stability has attracted an enormous amount of attention, even though its photoluminescence still requires to clarification. Herein, the controllable phase transformation between three-dimensional CsPbBr3 and zero-dimensional Cs4PbBr6 is easily achieved in a facile ligand-assisted supersaturated recrystallization synthesis procedure via tuning the amount of surfactants, and their unique optical properties are investigated and compared in detail. Both Cs4PbBr6 and CsPbBr3 produce remarkably intense green luminescence with quantum yields up to 45% and 80%, respectively; however, significantly different emitting behaviors are observed. The fluorescence lifetime of Cs4PbBr6 is much longer than that of CsPbBr3, and photo-blinking is easily detected in the Cs4PbBr6 product, proving that the zero-dimensional Cs4PbBr6 is indeed a highly luminescent perovskite-related material. Additionally, for the first time, tunable emissions over the visible-light spectral region are demonstrated to be achievable via halogen composition modulations in the Cs4PbX6 (X = Cl, Br, I) samples. Our study brings a simple method for the phase control of CsPbBr3/Cs4PbBr6 and demonstrates the intrinsic luminescence nature of the zero-dimensional perovskite-related Cs4PbX6 products.

Estimating BrAC from transdermal alcohol concentration data using the BrAC estimator software program.

Science.gov (United States)

Luczak, Susan E; Rosen, I Gary

2014-08-01

Transdermal alcohol sensor (TAS) devices have the potential to allow researchers and clinicians to unobtrusively collect naturalistic drinking data for weeks at a time, but the transdermal alcohol concentration (TAC) data these devices produce do not consistently correspond with breath alcohol concentration (BrAC) data. We present and test the BrAC Estimator software, a program designed to produce individualized estimates of BrAC from TAC data by fitting mathematical models to a specific person wearing a specific TAS device. Two TAS devices were worn simultaneously by 1 participant for 18 days. The trial began with a laboratory alcohol session to calibrate the model and was followed by a field trial with 10 drinking episodes. Model parameter estimates and fit indices were compared across drinking episodes to examine the calibration phase of the software. Software-generated estimates of peak BrAC, time of peak BrAC, and area under the BrAC curve were compared with breath analyzer data to examine the estimation phase of the software. In this single-subject design with breath analyzer peak BrAC scores ranging from 0.013 to 0.057, the software created consistent models for the 2 TAS devices, despite differences in raw TAC data, and was able to compensate for the attenuation of peak BrAC and latency of the time of peak BrAC that are typically observed in TAC data. This software program represents an important initial step for making it possible for non mathematician researchers and clinicians to obtain estimates of BrAC from TAC data in naturalistic drinking environments. Future research with more participants and greater variation in alcohol consumption levels and patterns, as well as examination of gain scheduling calibration procedures and nonlinear models of diffusion, will help to determine how precise these software models can become. Copyright © 2014 by the Research Society on Alcoholism.

Licensed operating reactors: Status summary report, data as of 02-28-89

International Nuclear Information System (INIS)

1989-03-01

The US Nuclear Regulatory Commission's monthly Licensed Operating Reactor Status Summary Report provides data on the operation of nuclear units as timely and accurately as possible. This report is divided into three sections: the first contains monthly highlights and statistics for commercial operating units, and errata from previously reported data; the second is a compilation of detailed information on each unit, provided by NRC Regional Offices, IE Headquarters and the Utilities; and the third section is an appendix for miscellaneous information such as spent fuel storage capability, reactor years of experience and non-power reactors in the United States

Re-determination and re-evaluation of the f and α parameters in channels Y4 and S84 of the BR1 reactor, for use in k 0-NAA at DSM Research

International Nuclear Information System (INIS)

Wispelaere, A. de; Corte, F. de; Bossus, D.A.W.; Swagten, J.J.M.G.; Vermaercke, P.

2006-01-01

Since the introduction of k 0 -based NAA as an analytical tool in 1989, all irradiations by DSM Research are done in channels Y4 and S84 of the BR1 reactor in Mol (Belgium). The last determination of f and α-values for these channels was performed in 1993. Although the configuration of the reactor did not change over all these years and therefore no change in f and α was to be expected, DSM Research decided to re-determine both parameters in both channels. Having much experience in this field, the INW k 0 -group was asked by DSM Research to perform this re-determination, in co-operation with the SCK, Mol. As the flux in channel Y4 is not constant during the start up and the scramming of the reactor, a numerical integration method was applied. This is a new approach in comparison with all previous reported data from DSM Research, where this change in flux was not taken into account. For the work presented here, use was made of the most recent nuclear data available in the literature

Characterization of LWR fuel rod irradiations with power transients in the BR2 reflector

International Nuclear Information System (INIS)

Ponsard, B.; Bodart, S.; Meer, K. van der; Raedt, C. de

1996-01-01

Fuel rod irradiations in reflector positions of the materials testing reactor BR2 are becoming increasingly important. A typical example is that of irradiation devices containing single LWR fuel rods, to be tested in the framework of a new international fuel investigation and development programme. Some of the irradiations will comprise power transients with central fuel melting (at 2800 deg. C), the power increase being obtained by decreasing the pressure in a He-3 neutron absorbing screen and/or by varying the BR2 reactor operating power. A total power variation by a factor of at least 2.5 in the fuel rod irradiated could thus be achieved. In some of the rods, central temperature measurements (up to 2000 deg. C) will be carried out. Both fresh and pre-irradiated fuel rods are concerned in the programme. For these irradiations, the accurate knowledge of the neutron-induced fission heating and of the gamma heating is required, as one of the purposes of the programme consists in establishing the correlation among the thermal conductivity, the burn-up and the irradiation temperature. Calibration work among various measuring methods and between measurements and one- and two-dimensional calculations is being pursued. (author). 10 refs, 15 figs, 3 tabs

Br2 elimination in 248-nm photolysis of CF2Br2 probed by using cavity ring-down absorption spectroscopy.

Science.gov (United States)

Hsu, Ching-Yi; Huang, Hong-Yi; Lin, King-Chuen

2005-10-01

By using cavity ring-down absorption spectroscopy technique, we have observed the channel of Br2 molecular elimination following photodissociation of CF2Br2 at 248 nm. A tunable laser beam, which is crossed perpendicular to the photolyzing laser beam in a ring-down cell, is used to probe the Br2 fragment in the B 3Piou+-X1Sigmag+ transition. The vibrational population is obtained in a nascent state, despite ring-down time as long as 500-1000 ns. The population ratio of Br2(v=1)/Br2(v=0) is determined to be 0.4+/-0.2, slightly larger than the value of 0.22 evaluated by Boltzmann distribution at room temperature. The quantum yield of the Br2 elimination reaction is also measured to be 0.04+/-0.01. This work provides direct evidence to support molecular elimination occurring in the CF2Br2 photodissociation and proposes a plausible pathway with the aid of ab initio potential-energy calculations. CF2Br2 is excited probably to the 1B1 and 3B2 states at 248 nm. As the C-Br bond is elongated upon excitation, the coupling of the 1A'(1B1) state to the high vibrational levels of the ground state X 1A'(1A1) may be enhanced to facilitate the process of internal conversion. After transition, the highly vibrationally excited CF2Br2 feasibly surpasses a transition barrier prior to decomposition. According to the ab initio calculations, the transition state structure tends to correlate with the intermediate state CF2Br+Br(CF2Br...Br) and the products CF2+Br2. A sequential photodissociation pathway is thus favored. That is, a single C-Br bond breaks, and then the free-Br atom moves to form a Br-Br bond, followed by the Br2 elimination. The formed Br-Br bond distance in the transition state tends to approach equilibrium such that the Br2 fragment may be populated in cold vibrational distribution. Observation of a small vibrational population ratio of Br2(v=1)Br2(v=0) agrees with the proposed mechanism.

Elimination mechanisms of Br2+ and Br+ in photodissociation of 1,1- and 1,2-dibromoethylenes using velocity imaging technique

International Nuclear Information System (INIS)

Hua Linqiang; Zhang Bing; Lee, Wei-Bin; Chao, Meng-Hsuan; Lin, King-Chuen

2011-01-01

Elimination pathways of the Br 2 + and Br + ionic fragments in photodissociation of 1,2- and 1,1-dibromoethylenes (C 2 H 2 Br 2 ) at 233 nm are investigated using time-of-flight mass spectrometer equipped with velocity ion imaging. The Br 2 + fragments are verified not to stem from ionization of neutral Br 2 , that is a dissociation channel of dibromoethylenes reported previously. Instead, they are produced from dissociative ionization of dibromoethylene isomers. That is, C 2 H 2 Br 2 is first ionized by absorbing two photons, followed by the dissociation scheme, C 2 H 2 Br 2 + + hv→Br 2 + + C 2 H 2 . 1,2-C 2 H 2 Br 2 gives rise to a bright Br 2 + image with anisotropy parameter of -0.5 ± 0.1; the fragment may recoil at an angle of ∼66 deg. with respect to the C = C bond axis. However, this channel is relatively slow in 1,1-C 2 H 2 Br 2 such that a weak Br 2 + image is acquired with anisotropy parameter equal to zero, indicative of an isotropic recoil fragment distribution. It is more complicated to understand the formation mechanisms of Br + . Three routes are proposed for dissociation of 1,2-C 2 H 2 Br 2 , including (a) ionization of Br that is eliminated from C 2 H 2 Br 2 by absorbing one photon, (b) dissociation from C 2 H 2 Br 2 + by absorbing two more photons, and (c) dissociation of Br 2 + . Each pathway requires four photons to release one Br + , in contrast to the Br 2 + formation that involves a three-photon process. As for 1,1-C 2 H 2 Br 2 , the first two pathways are the same, but the third one is too weak to be detected.

Photodissociation of C{sub 3}H{sub 5}Br and C{sub 4}H{sub 7}Br at 234 nm

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyun Kook; Paul, Dababrata; Hong, Ki Ryong; Cho, Ha Na; Kim, Tae Kyu [Pusan National University, Busan (Korea, Republic of); Lee, Kyoung Seok [Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

2012-01-15

The photodissociation dynamics of cyclopropyl bromide (C-3H{sub 5}Br) and cyclobutyl bromide (C{sub 4}H{sub 7}Br) at 234 nm was investigated. A two-dimensional photofragment ion-imaging technique coupled with a [2+1] resonance enhanced multiphoton ionization scheme was utilized to obtain speed and angular distributions of the nascent Br({sup 2}P{sub 3/2}) and Br*({sup 2}P{sub 1/2}) atoms. The recoil anisotropies for the Br and Br* channels were measured to be βBr = 0.92 ± 0.03 and βBr* = 1.52 ± 0.04 for C{sub 3}H{sub 5}Br and βBr = 1.10 ± 0.03 and βBr* = 1.49 ± 0.05 for C{sub 4}H{sub 7}Br. The relative quantum yield for Br was found to be ΦBr = 0.13 ± 0.03 and for C{sub 3}H{sub 5}Br and C{sub 4}H{sub 7}Br, respectively. The soft radical limit of the impulsive model adequately modeled the related energy partitioning. The nonadiabatic transition probability from the 3A' and 4A' potential energy surfaces was estimated and discussed.

Austin: austenitic steel irradiation E 145-02 Irradiation Report

International Nuclear Information System (INIS)

Genet, F.; Konrad, J.

1987-01-01

Safety measures for nuclear reactors require that the energy which might be liberated in a reactor core during an accident should be contained within the reactor pressure vessel, even after very long irradiation periods. Hence the need to know the mechanical properties at high deformation velocity of structure materials that have received irradiation damage due to their utilization. The stainless steels used in the structures of reactors undergo damage by both thermal and fast neutrons, causing important changes in the mechanical properties of these materials. Various austenitic steels available as structural materials were irradiated or are under irradiation in various reactors in order to study the evolution of the mechanical properties at high deformation velocity as a function of the irradiation damage rate. The experiment called AUSTIN (AUstenitic STeel IrradiatioN) 02 was performed by the JRC Petten Establishment on behalf of Ispra in support of the reactor safety programme

XeBr exciplex laser

International Nuclear Information System (INIS)

Searles, S.K.

1976-01-01

Laser emission from the recently discovered XeBr exciplex laser was investigated as a function of the partial pressures of Xe and Br 2 . An optical loss process appears to limit high-pressure operation

Elimination of nonspecific radioactivity from [{sup 76}Br]bromide in PET study with [{sup 76}Br]bromodeoxyuridine

Energy Technology Data Exchange (ETDEWEB)

Li Lu; Bergstroem, Mats E-mail: Mats.Bergstroem@pet.uu.se; Fasth, Karl-Johan; Wu Feng; Eriksson, Barbro; Laangstroem, Bengt

1999-10-01

[{sup 76}Br]Bromodeoxyuridine ([{sup 76}Br]BrdU) might allow a determination of proliferation in vivo using positron emission tomography (PET), but only with consideration of organ nonspecific radioactivity constituted by [{sup 76}Br]bromide. A first study assessed the potential of diuretics to eliminate [{sup 76}Br]bromide. [{sup 76}Br]Bromide was injected in the vein of rats and different diuretic combinations were given. Urine was collected and radioactivity measured. Torasemide plus sodium chloride gave better {sup 76}Br elimination than the other diuretics. In a second experiment, rats were given [{sup 76}Br]BrdU. After the radioactivity injection, the rats of the treatment group were given torasemide plus NaCl. At 44 h after the radioactivity injection, the radioactivity concentration and the fraction incorporated into DNA were measured in different organs. Using diuretics, the elimination of [{sup 76}Br]bromide was increased. The radioactivity decreased 30-50% in most of the organs but the highest radioactivity uptake was found in the organs with more active DNA synthesis. This method may facilitate the use of [{sup 76}Br]BrdU as a tracer for DNA synthesis using PET.

Partial structures in molten AgBr

Energy Technology Data Exchange (ETDEWEB)

Ueno, Hiroki [Department of Condensed Matter Chemistry and Physics, Faculty of Sciences, Kyushu University, 4-2-1 Ropponmatsu, Chuo-ku, Fukuoka 810-8560 (Japan)], E-mail: ueno@gemini.rc.kyushu-u.ac.jp; Tahara, Shuta [Faculty of Pharmacy, Niigata University of Pharmacy and Applied Life Science, Higashijima, Akiha-ku, Niigata 956-8603 (Japan); Kawakita, Yukinobu [Department of Physics, Faculty of Sciences, Kyushu University, 4-2-1 Ropponmatsu, Chuo-ku, Fukuoka 810-8560 (Japan); Kohara, Shinji [Research and Utilization Division, Japan Synchrotron Radiation Research Institute (JASRI, SPring-8), 1-1-1 Koto, Sayo-cho, Sayo-gun, Hyogo 679-5198 (Japan); Takeda, Shin' ichi [Department of Physics, Faculty of Sciences, Kyushu University, 4-2-1 Ropponmatsu, Chuo-ku, Fukuoka 810-8560 (Japan)

2009-02-21

The structure of molten AgBr has been studied by means of neutron and X-ray diffractions with the aid of structural modeling. It is confirmed that the Ag-Ag correlation has a small but well-defined first peak in the partial pair distribution function whose tail penetrates into the Ag-Br nearest neighbor distribution. This feature on the Ag-Ag correlation is intermediate between that of molten AgCl (non-superionic melt) and that of molten AgI (superionic melt). The analysis of Br-Ag-Br bond angle reveals that molten AgBr preserves a rocksalt type local ordering in the solid phase, suggesting that molten AgBr is clarified as non-superionic melt like molten AgCl.

Investigations on the system Te/O/Br

International Nuclear Information System (INIS)

Oppermann, H.; Kunze, G.; Wolf, E.; Titov, V.A.; Kokovin, G.A.

1978-01-01

The melting point diagram of the system TeBr 4 -TeO 2 was obtained by total pressure measurements and DTA measurements. A congruent melting composition Te 6 O 11 Br 2 exists, the melting point is 570 0 C. The enthalpy of formation and the standard entropy of the species TeOBr 2 ,g was derived from measurements of the total pressure over Te 6 O 11 Br 2 /TeBr 4 and from the transport behaviour of the TeO 2 with Br 2 . From the decomposition-pressure measurements over Te 6 O 11 Br 2 /TeO 2 follow the partial pressures. The enthalpy of formation ΔH 0 (Te 6 O 11 Br 2 ,f,298) -453.5 kcal/Mol was obtained from the enthalpy of solution. The transport-behaviour of TeO 2 with HBr, TeBr 4 and Br 2 and that of Te 6 O 11 Br 2 is clear with the thermodynamic data of TeOBr 2 . (author)

Polymeric anionic networks using dibromine as a crosslinker; the preparation and crystal structure of [(C4H9)4N]2[Pt2Br10].(Br2)7 and [(C4H9)4N]2[PtBr4Cl2].(Br2)6.

Science.gov (United States)

Berkei, Michael; Bickley, Jamie F; Heaton, Brian T; Steiner, Alexander

2002-09-21

The reaction of M[PtX3(CO)] (M+ = [(C4H9)4N]+, X = Br, Cl) with an excess of Br2 gives the new platinum(IV) salts, [(C4H9)4N]2[Pt2Br10].(Br2)7, 1, and [(C4H9)4N]2[PtBr4Cl2].(Br2)6, 2, which, in the solid state, contain strong Br Br interactions resulting in the formation of polymeric networks; they could provide useful solid storage reservoirs for elemental bromine.

Addition reaction of adamantylideneadamantane with Br2 and 2Br2: a computational study.

Science.gov (United States)

Islam, Shahidul M; Poirier, Raymond A

2008-01-10

Ab initio calculations were carried out for the reaction of adamantylideneadamantane (Ad=Ad) with Br2 and 2Br2. Geometries of the reactants, transition states, intermediates, and products were optimized at HF and B3LYP levels of theory using the 6-31G(d) basis set. Energies were also obtained using single point calculations at the MP2/6-31G(d)//HF/6-31G(d), MP2/6-31G(d)//B3LYP/6-31G(d), and B3LYP/6-31+G(d)//B3LYP/6-31G(d) levels of theory. Intrinsic reaction coordinate (IRC) calculations were performed to characterize the transition states on the potential energy surface. Only one pathway was found for the reaction of Ad=Ad with one Br2 producing a bromonium/bromide ion pair. Three mechanisms for the reaction of Ad=Ad with 2Br2 were found, leading to three different structural forms of the bromonium/Br3- ion pair. Activation energies, free energies, and enthalpies of activation along with the relative stability of products for each reaction pathway were calculated. The reaction of Ad=Ad with 2Br2 was strongly favored over the reaction with only one Br2. According to B3LYP/6-31G(d) and single point calculations at MP2, the most stable bromonium/Br3- ion pair would form spontaneously. The most stable of the three bromonium/Br3- ion pairs has a structure very similar to the observed X-ray structure. Free energies of activation and relative stabilities of reactants and products in CCl4 and CH2ClCH2Cl were also calculated with PCM using the united atom (UA0) cavity model and, in general, results similar to the gas phase were obtained. An optimized structure for the trans-1,2-dibromo product was also found at all levels of theory both in gas phase and in solution, but no transition state leading to the trans-1,2-dibromo product was obtained.

Computations on the primary photoreaction of Br2 with CO2: stepwise vs concerted addition of Br atoms.

Science.gov (United States)

Xu, Kewei; Korter, Timothy M; Braiman, Mark S

2015-04-09

It was proposed previously that Br2-sensitized photolysis of liquid CO2 proceeds through a metastable primary photoproduct, CO2Br2. Possible mechanisms for such a photoreaction are explored here computationally. First, it is shown that the CO2Br radical is not stable in any geometry. This rules out a free-radical mechanism, for example, photochemical splitting of Br2 followed by stepwise addition of Br atoms to CO2-which in turn accounts for the lack of previously observed Br2+CO2 photochemistry in gas phases. A possible alternative mechanism in liquid phase is formation of a weakly bound CO2:Br2 complex, followed by concerted photoaddition of Br2. This hypothesis is suggested by the previously published spectroscopic detection of a binary CO2:Br2 complex in the supersonically cooled gas phase. We compute a global binding-energy minimum of -6.2 kJ mol(-1) for such complexes, in a linear geometry. Two additional local minima were computed for perpendicular (C2v) and nearly parallel asymmetric planar geometries, both with binding energies near -5.4 kJ mol(-1). In these two latter geometries, C-Br and O-Br bond distances are simultaneously in the range of 3.5-3.8 Å, that is, perhaps suitable for a concerted photoaddition under the temperature and pressure conditions where Br2 + CO2 photochemistry has been observed.

Overview of the fast reactors fuels program

International Nuclear Information System (INIS)

Evans, E.A.; Cox, C.M.; Hayward, B.R.; Rice, L.H.; Yoshikawa, H.H.

1980-04-01

Each nation involved in LMFBR development has its unique energy strategies which consider energy growth projections, uranium resources, capital costs, and plant operational requirements. Common to all of these strategies is a history of fast reactor experience which dates back to the days of the Manhatten Project and includes the CLEMENTINE Reactor, which generated a few watts, LAMPRE, EBR-I, EBR-II, FERMI, SEFOR, FFTF, BR-1, -2, -5, -10, BOR-60, BN-350, BN-600, JOYO, RAPSODIE, Phenix, KNK-II, DFR, and PFR. Fast reactors under design or construction include PEC, CRBR, SuperPhenix, SNR-300, MONJU, and Madras (India). The parallel fuels and materials evolution has fully supported this reactor development. It has involved cermets, molten plutonium alloy, plutonium oxide, uranium metal or alloy, uranium oxide, and mixed uranium-plutonium oxides and carbides

Predecommissioning radiological survey of BR3 infrastructures

International Nuclear Information System (INIS)

Cantrel, E.

2006-01-01

The decommissioning of the BR3 (Belgian Reactor 3) approaches its final phase, in which the buildings infrastructures are being decontaminated targeting either the reuse or the conventional demolition after denuclearisation. In a PWR with a significant operation lifetime, such as the BR3, maintenance operations, failure and/or leakages, incidents occurring in the different circuits of the plant result in the contamination of the buildings infrastructures at various activity levels with contaminants penetrating/migrating up to several cm inside the material bulk structure. Moreover, the BR3 bioshield has been exposed to rather high neutron leakage fluxes during the reactor operation and is therefore activated. The different radiological situations faced require the implementation of different characterization methodologies based on the use of an adequate combination of measurement devices and/or sampling devices. The non-destructive assay of activation depth using the ISOCS (In Situ Object Counting System) and a specific spectra analysis protocol has been tested in 2004. The first results obtained were encouraging and the qualification program for activated material is running. We are now investigating the possibilities to extend the methodology to building materials contaminated in-depth with 137 Cs. The overall process of dismantling/denuclearization of the BR3 building infrastructure consists of: (1) a preliminary characterization and determination of the contamination or activation depth; (2) the determination of the decontamination method; (3) the effective decontamination and clean up; (4) a possible intermediate characterization followed by an additional decontamination step; and (5) the characterization for clearance. The more accurate the preliminary survey is performed the less additional control/decontamination cycles are needed to reach clearance levels. The pre-decommissioning characterization process includes a preliminary categorisation (see picture

Density Functional Study of Structures and Electron Affinities of BrO4F/BrO4F-

Directory of Open Access Journals (Sweden)

Wei Li

2009-07-01

Full Text Available The structures, electron affinities and bond dissociation energies of BrO4F/BrO4F− species have been investigated with five density functional theory (DFT methods with DZP++ basis sets. The planar F-Br…O2…O2 complexes possess 3A' electronic state for neutral molecule and 4A' state for the corresponding anion. Three types of the neutral-anion energy separations are the adiabatic electron affinity (EAad, the vertical electron affinity (EAvert, and the vertical detachment energy (VDE. The EAad value predicted by B3LYP method is 4.52 eV. The bond dissociation energies De (BrO4F → BrO4-mF + Om (m = 1-4 and De- (BrO4F- → BrO4-mF- + Om and BrO4F- → BrO4-mF + Om- are predicted. The adiabatic electron affinities (EAad were predicted to be 4.52 eV for F-Br…O2…O2 (3A'← 4A' (B3LYP method.

RETRAN-02 installation and verification for the CRAY computer

International Nuclear Information System (INIS)

1990-03-01

The RETRAN-02 transient thermal-hydraulic analysis program developed by the Electric Power Research Institute (EPRI) has been selected as a tool for use in assessing the operation and safety of the SP-100 space reactor system being developed at Los Alamos National Laboratory (LANL). The released versions of RETRAN-02 are not operational on CRAY computer systems which are the primary mainframes in use at LANL requiring that the code be converted to the CRAY system. This document describes the code conversion, installation, and validation of the RETRAN-02/MOD004 code on the LANL CRAY computer system

Annealing Effect on (FAPbI31−x(MAPbBr3x Perovskite Films in Inverted-Type Perovskite Solar Cells

Directory of Open Access Journals (Sweden)

Lung-Chien Chen

2016-09-01

Full Text Available This study determines the effects of annealing treatment on the structure and the optical and electronic behaviors of the mixed (FAPbI31−x(MAPbBr3x perovskite system. The experimental results reveal that (FAPbI31−x(MAPbBr3x (x ~ 0.2 is an effective light-absorbing material for use in inverted planar perovskite solar cells owing to its large absorbance and tunable band gap. Therefore, good band-matching between the (FAPbI31−x(MAPbBr3x and C60 in photovoltaic devices can be controlled by annealing at various temperatures. Accordingly, an inverted mixed perovskite solar cell with a record efficiency of 12.0% under AM1.5G irradiation is realized.

Postsynthesis Transformation of Insulating Cs4PbBr6 Nanocrystals into Bright Perovskite CsPbBr3 through Physical and Chemical Extraction of CsBr.

Science.gov (United States)

Palazon, Francisco; Urso, Carmine; De Trizio, Luca; Akkerman, Quinten; Marras, Sergio; Locardi, Federico; Nelli, Ilaria; Ferretti, Maurizio; Prato, Mirko; Manna, Liberato

2017-10-13

Perovskite-related Cs 4 PbBr 6 nanocrystals present a "zero-dimensional" crystalline structure where adjacent [PbBr 6 ] 4- octahedra do not share any corners. We show in this work that these nanocrystals can be converted into "three-dimensional" CsPbBr 3 perovskites by extraction of CsBr. This conversion drastically changes the optoelectronic properties of the nanocrystals that become highly photoluminescent. The extraction of CsBr can be achieved either by thermal annealing (physical approach) or by chemical reaction with Prussian Blue (chemical approach). The former approach can be simply carried out on a dried film without addition of any chemicals but does not yield a full transformation. Instead, reaction with Prussian Blue in solution achieves a full transformation into the perovskite phase. This transformation was also verified on the iodide counterpart (Cs 4 PbI 6 ).

Dicty_cDB: FC-BR23 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available FC (Link to library) FC-BR23 (Link to dictyBase) - - - Contig-U15008-1 FC-BR23Z (Li...nk to Original site) - - FC-BR23Z 641 - - - - Show FC-BR23 Library FC (Link to library) Clone ID FC-BR23 (Li.../dictycdb.biol.tsukuba.ac.jp/CSM/FC/FC-BR/FC-BR23Q.Seq.d/ Representative seq. ID FC-BR2...3Z (Link to Original site) Representative DNA sequence >FC-BR23 (FC-BR23Q) /CSM/FC/FC-BR/FC-BR23Q.Seq....9 0.0 SLA211 (SLA211Q) /CSM/SL/SLA2-A/SLA211Q.Seq.d/ 1029 0.0 FC-BR23 (FC-BR23Q) /CSM/FC/FC-BR/FC-BR2

Balloon-borne stratospheric BrO measurements: comparison with Envisat/SCIAMACHY BrO limb profiles

Directory of Open Access Journals (Sweden)

M. Dorf

2006-01-01

Full Text Available For the first time, results of four stratospheric BrO profiling instruments, are presented and compared with reference to the SLIMCAT 3-dimensional chemical transport model (3-D CTM. Model calculations are used to infer a BrO profile validation set, measured by 3 different balloon sensors, for the new Envisat/SCIAMACHY (ENVIronment SATellite/SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY satellite instrument. The balloon observations include (a balloon-borne in situ resonance fluorescence detection of BrO (Triple, (b balloon-borne solar occultation DOAS measurements (Differential Optical Absorption Spectroscopy of BrO in the UV, and (c BrO profiling from the solar occultation SAOZ (Systeme d'Analyse par Observation Zenithale balloon instrument. Since stratospheric BrO is subject to considerable diurnal variation and none of the measurements are performed close enough in time and space for a direct comparison, all balloon observations are considered with reference to outputs from the 3-D CTM. The referencing is performed by forward and backward air mass trajectory calculations to match the balloon with the satellite observations. The diurnal variation of BrO is considered by 1-D photochemical model calculation along the trajectories. The 1-D photochemical model is initialised with output data of the 3-D model with additional constraints on the vertical transport, the total amount and photochemistry of stratospheric bromine as given by the various balloon observations. Total [Bry]=(20.1±2.5 pptv obtained from DOAS BrO observations at mid-latitudes in 2003, serves as an upper limit of the comparison. Most of the balloon observations agree with the photochemical model predictions within their given error estimates. First retrieval exercises of BrO limb profiling from the SCIAMACHY satellite instrument on average agree to around 20% with the photochemically-corrected balloon observations of the remote sensing instruments (SAOZ

Energikravene i BR15

DEFF Research Database (Denmark)

Kragh, Jesper; Aggerholm, Søren

2015-01-01

Bygningsreglement 2015 – BR15 – gælder fra 1. januar 2016 med en overgangsfase frem til 1. juli 2016. Det bygger videre på BR10 og de tidligere udmeldte krav til nybyggeriet frem mod 2020. I denne kvikguide får du hurtigt overblik over, hvordan du sikrer, at de bygninger, du er med til at opføre...... eller renovere, lever op til BR15’s energikrav. Disse krav findes primært i reglementets kapitel 7 om energiforbrug og i kapitel 8 om installationer samt i kapitel 6 om indeklima....

Evaluation of responses to IE Bulletin 82-02: degradation of threaded fasteners in reactor coolant pressure boundary of pressurized-water-reactor plants

International Nuclear Information System (INIS)

Anderson, W.; Sterner, P.

1985-05-01

IE Bulletin 82-02 was issued by the NRC on June 2, 1982, to notify licensees about incidents of severe degradation of threaded fasteners. The bulletin required appropriate action including submittal of information from pressurized water reactors having an operating license. Responses from 41 licensees included their recent experience with degradation of threaded fasteners in primary system components. Data from recent regular inspections of reactor coolant pressure boundary component connections of 6-in. size and larger are compiled for technical evaluation. Statistical analysis is used to determine significant factors related to frequency of leakage incidents in connections, occurrence of degradation of bolts and studs, and the need for bolt replacement. Factors examined include the age of the plant, types of components, use of lubricants and sealants, and differences between plants. The compiled data indicate that, on the average, 10% of the bolted connections show evidence of leaking during an 18-month period. Also, 80% of the connections that show evidence of leakage undergo some degradation of the bolting. Results of the analysis show a significant decrease in the occurrence of bolting degradation events as the age of the plant increases. The data also show that valves are less subject to bolting corrosion. A group of 5 of the 41 plants accounted for about one-half of the reported leakage and corrosion events. The common characteristic found for four of these five plants was the lubricant used. The use of nickel-graphite based lubricants appears to offer a significantly reduced incidence of leakage and corrosion, based on late corrections to the reported data. The data also permit the conclusion that the use of molybdenum-disulfide-based lubricants and graphite-based lubricants results in a significantly increased incidence of leakage and corrosion. Reporting of data on lubricants was of poor quality and detracted from the value of the bulletin responses

Solvation dynamics through Raman spectroscopy: hydration of Br2 and Br3(-), and solvation of Br2 in liquid bromine.

Science.gov (United States)

Branigan, Edward T; Halberstadt, N; Apkarian, V A

2011-05-07

Raman spectroscopy of bromine in the liquid phase and in water illustrates uncommon principles and yields insights regarding hydration. In liquid Br(2), resonant excitation over the B((3)Π(0u)(+)) ← X((1)Σ(g)(+)) valence transition at 532 nm produces a weak resonant Raman (RR) progression accompanied by a five-fold stronger non-resonant (NR) scattering. The latter is assigned to pre-resonance with the C-state, which in turn must be strongly mixed with inter-molecular charge transfer states. Despite the electronic resonance, RR of Br(2) in water is quenched. At 532 nm, the homogeneously broadened fundamental is observed, as in the NR case at 785 nm. The implications of the quenching of RR scattering are analyzed in a simple, semi-quantitative model, to conclude that the inertial evolution of the Raman packet in aqueous Br(2) occurs along multiple equivalent water-Br(2) coordinates. In distinct contrast with hydrophilic hydration in small clusters and hydrophobic hydration in clathrates, it is concluded that the hydration shell of bromine in water consists of dynamically equivalent fluxional water molecules. At 405 nm, the RR progression of Br(3)(-) is observed, accompanied by difference transitions between the breathing of the hydration shell and the symmetric stretch of the ion. The RR scattering process in this case can be regarded as the coherent photo-induced electron transfer to the solvent and its radiative back-transfer.

Measurement of the ratio of branching ratios BR(B+ → J/ψK+)/BR(B0 → J/φK0) and BR(B+ → J/ψK+)/BR(B+ → J/ψK*+)

International Nuclear Information System (INIS)

Atavales, J. B. G.

1995-01-01

A preliminary measurement of the ratio of branching ratios BR(B + → J/ψK + )/BR(B 0 → J/ψK 0 ) and BR(B + → J/ψK + )/BR(B + → J/ψK *+ ) is made by fully reconstructing each mode, where J/ψ → μ + μ - , K *+ → K 0 s π + and K 0 s → π + π - . The data were taken with the CDF detector during the 1993 run. The total integrated luminosity is ∼ 20pb -1 resulting in a sample of about 170 J/ψK ± , 50 J/ψK 0 S and 25 J/ψK *± candidate events. The results will be reported

Mercury adsorption characteristics of HBr-modified fly ash in an entrained-flow reactor.

Science.gov (United States)

Zhang, Yongsheng; Zhao, Lilin; Guo, Ruitao; Song, Na; Wang, Jiawei; Cao, Yan; Orndorff, William; Pan, Wei-ping

2015-07-01

In this study, the mercury adsorption characteristics of HBr-modified fly ash in an entrained-flow reactor were investigated through thermal decomposition methods. The results show that the mercury adsorption performance of the HBr-modified fly ash was enhanced significantly. The mercury species adsorbed by unmodified fly ash were HgCl2, HgS and HgO. The mercury adsorbed by HBr-modified fly ash, in the entrained-flow reactor, existed in two forms, HgBr2 and HgO, and the HBr was the dominant factor promoting oxidation of elemental mercury in the entrained-flow reactor. In the current study, the concentration of HgBr2 and HgO in ash from the fine ash vessel was 4.6 times greater than for ash from the coarse ash vessel. The fine ash had better mercury adsorption performance than coarse ash, which is most likely due to the higher specific surface area and longer residence time. Copyright © 2015. Published by Elsevier B.V.

Reactivity of BrCl, Br₂, BrOCl, Br₂O, and HOBr toward dimethenamid in solutions of bromide + aqueous free chlorine.

Science.gov (United States)

Sivey, John D; Arey, J Samuel; Tentscher, Peter R; Roberts, A Lynn

2013-02-05

HOBr, formed via oxidation of bromide by free available chlorine (FAC), is frequently assumed to be the sole species responsible for generating brominated disinfection byproducts (DBPs). Our studies reveal that BrCl, Br(2), BrOCl, and Br(2)O can also serve as brominating agents of the herbicide dimethenamid in solutions of bromide to which FAC was added. Conditions affecting bromine speciation (pH, total free bromine concentration ([HOBr](T)), [Cl(-)], and [FAC](o)) were systematically varied, and rates of dimethenamid bromination were measured. Reaction orders in [HOBr](T) ranged from 1.09 (±0.17) to 1.67 (±0.16), reaching a maximum near the pK(a) of HOBr. This complex dependence on [HOBr](T) implicates Br(2)O as an active brominating agent. That bromination rates increased with increasing [Cl(-)], [FAC](o) (at constant [HOBr](T)), and excess bromide (where [Br(-)](o)>[FAC](o)) implicate BrCl, BrOCl, and Br(2), respectively, as brominating agents. As equilibrium constants for the formation of Br(2)O and BrOCl (aq) have not been previously reported, we have calculated these values (and their gas-phase analogues) using benchmark-quality quantum chemical methods [CCSD(T) up to CCSDTQ calculations plus solvation effects]. The results allow us to compute bromine speciation and hence second-order rate constants. Intrinsic brominating reactivity increased in the order: HOBr ≪ Br(2)O Br(2) < BrCl. Our results indicate that species other than HOBr can influence bromination rates under conditions typical of drinking water and wastewater chlorination.

Overview of the fast reactors fuels program. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Evans, E.A.; Cox, C.M.; Hayward, B.R.; Rice, L.H.; Yoshikawa, H.H.

1980-04-01

Each nation involved in LMFBR development has its unique energy strategies which consider energy growth projections, uranium resources, capital costs, and plant operational requirements. Common to all of these strategies is a history of fast reactor experience which dates back to the days of the Manhatten Project and includes the CLEMENTINE Reactor, which generated a few watts, LAMPRE, EBR-I, EBR-II, FERMI, SEFOR, FFTF, BR-1, -2, -5, -10, BOR-60, BN-350, BN-600, JOYO, RAPSODIE, Phenix, KNK-II, DFR, and PFR. Fast reactors under design or construction include PEC, CRBR, SuperPhenix, SNR-300, MONJU, and Madras (India). The parallel fuels and materials evolution has fully supported this reactor development. It has involved cermets, molten plutonium alloy, plutonium oxide, uranium metal or alloy, uranium oxide, and mixed uranium-plutonium oxides and carbides.

The BR eigenvalue algorithm

Energy Technology Data Exchange (ETDEWEB)

Geist, G.A. [Oak Ridge National Lab., TN (United States). Computer Science and Mathematics Div.; Howell, G.W. [Florida Inst. of Tech., Melbourne, FL (United States). Dept. of Applied Mathematics; Watkins, D.S. [Washington State Univ., Pullman, WA (United States). Dept. of Pure and Applied Mathematics

1997-11-01

The BR algorithm, a new method for calculating the eigenvalues of an upper Hessenberg matrix, is introduced. It is a bulge-chasing algorithm like the QR algorithm, but, unlike the QR algorithm, it is well adapted to computing the eigenvalues of the narrowband, nearly tridiagonal matrices generated by the look-ahead Lanczos process. This paper describes the BR algorithm and gives numerical evidence that it works well in conjunction with the Lanczos process. On the biggest problems run so far, the BR algorithm beats the QR algorithm by a factor of 30--60 in computing time and a factor of over 100 in matrix storage space.

Ultrafast Interfacial Electron and Hole Transfer from CsPbBr3 Perovskite Quantum Dots.

Science.gov (United States)

Wu, Kaifeng; Liang, Guijie; Shang, Qiongyi; Ren, Yueping; Kong, Degui; Lian, Tianquan

2015-10-14

Recently reported colloidal lead halide perovskite quantum dots (QDs) with tunable photoluminescence (PL) wavelengths covering the whole visible spectrum and exceptionally high PL quantum yields (QYs, 50-90%) constitute a new family of functional materials with potential applications in light-harvesting and -emitting devices. By transient absorption spectroscopy, we show that the high PL QYs (∼79%) can be attributed to negligible electron or hole trapping pathways in CsPbBr3 QDs: ∼94% of lowest excitonic states decayed with a single-exponential time constant of 4.5 ± 0.2 ns. Furthermore, excitons in CsPbBr3 QDs can be efficiently dissociated in the presence of electron or hole acceptors. The half-lives of electron transfer (ET) to benzoquinone and subsequent charge recombination are 65 ± 5 ps and 2.6 ± 0.4 ns, respectively. The half-lives for hole transfer (HT) to phenothiazine and the subsequent charge recombination are 49 ± 6 ps and 1.0 ± 0.2 ns, respectively. The lack of electron and hole traps and fast interfacial ET and HT rates are key properties that may enable the development of efficient lead halide perovskite QDs-based light-harvesting and -emitting devices.

Natural production of Tuber aestivum in central Spain: Pinus spp. versus Quercus spp. brûlés

Directory of Open Access Journals (Sweden)

Luis G. Garcia-Montero

2014-08-01

Full Text Available Aim of study: Tuber aestivum is the most widespread edible truffle, with increasing commercial interest. This species can produce carpophores with conifer hosts, in contrast with the inability of Pinus spp. to induce fruiting in other truffle species such as Tuber melanosporum. Therefore the objective is to compare the characteristics and carpophore production of T. aestivum brûlés associated with Pinus spp. versus Quercus spp.Area of study: We studied the natural habitats of T. aestivum in the Alto Tajo Nature Reserve in central Spain.Material and methods: During 5 years, we monitored the production of carpophores and brûlé size of 145 T. aestivum brûlés associated with Pinus nigra subsp. salzmanni and P. sylvestris and Quercus ilex subsp. ballota and Q. faginea hosts. Statistical treatment was performed using the Statistica Program v. 6.Main Results: The size of brûlés associated with Pinus was significantly smaller than that of brûlés associated with Quercus. However, carpophore production per brûlé, and especially for brûlés of similar size, was greater when the host plant was a pine. After accounting for brûlé size, the production of brûlés associated with Pinus spp. was 2.23 (95% CI, between 1.35 and 3.69 and 1.61 (95% CI, between 1.02 and 2.54 times greater than the production of brûlés associated with Quercus faginea and Q. ilex subsp. ballota, respectively.Research highlights: The considerable ability of Pinus nigra subsp. salzmanni and P. sylvestris to form effective brûlés and to produce carpophores of Tuber aestivum in natural conditions was clearly demonstrated, and suggest that those species can be of use in the culture of T. aestivum.Key words: Summer truffle; Tuber aestivum; truffle culture; truffle ecology; Pinus spp.; Quercus spp.

Immobilised native plant cysteine proteases: packed-bed reactor for white wine protein stabilisation

OpenAIRE

Benucci, Ilaria; Lombardelli, Claudio; Liburdi, Katia; Acciaro, Giuseppe; Zappino, Matteo; Esti, Marco

2015-01-01

This research presents a feasibility study of using a continuous packed-bed reactor (PBR), containing immobilised native plant cysteine proteases, as a specific and mild alternative technique relative to the usual bentonite fining for white wine protein stabilisation. The operational parameters for a PBR containing immobilised bromelain (PBR-br) or immobilised papain (PBR-pa) were optimised using model wine fortified with synthetic substrate (Bz-Phe-Val-Arg-pNA). The effectiveness of PBR-br, ...

IGORR 2: Proceedings of the 2. meeting of the International Group On Research Reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-07-01

The International group on Research Reactors was formed to facilitate the sharing of knowledge and experience among those institutions and individuals who are actively working to design, build, and promote new research reactors or to make significant upgrades to existing facilities. Sessions during this second meeting were devoted to research reactor reports (GRENOBLE reactor, FRM-II, HIFAR, PIK, reactors at JAERI, MAPLE, ANS, NIST, MURR, TRIGA, BR-2, SIRIUS 2); other neutron sources; and two workshops were dealing with research and development results and needs and reports on progress in needed of R and D areas identified at IGORR 1.

IGORR 2: Proceedings of the 2. meeting of the International Group On Research Reactors

International Nuclear Information System (INIS)

1992-01-01

The International group on Research Reactors was formed to facilitate the sharing of knowledge and experience among those institutions and individuals who are actively working to design, build, and promote new research reactors or to make significant upgrades to existing facilities. Sessions during this second meeting were devoted to research reactor reports (GRENOBLE reactor, FRM-II, HIFAR, PIK, reactors at JAERI, MAPLE, ANS, NIST, MURR, TRIGA, BR-2, SIRIUS 2); other neutron sources; and two workshops were dealing with research and development results and needs and reports on progress in needed of R and D areas identified at IGORR 1

Dicty_cDB: FC-BR21 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available FC (Link to library) FC-BR21 (Link to dictyBase) - - - Contig-U15384-1 | Contig-U16443-1 FC-BR2...1P (Link to Original site) FC-BR21F 551 FC-BR21Z 122 FC-BR21P 673 - - Show FC-BR21 Library FC (L...ink to library) Clone ID FC-BR21 (Link to dictyBase) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Cont...ig-U15384-1 | Contig-U16443-1 Original site URL http://dictycdb.biol.tsukuba.ac.jp/CSM/FC/FC-BR/FC-BR2...1Q.Seq.d/ Representative seq. ID FC-BR21P (Link to Original site) Representative DNA sequence >FC-BR21 (FC-BR2

Reactor kinetics calculated in the summation method and key delayed-neutron data

International Nuclear Information System (INIS)

Oyamatsu, Kazuhiro

2001-01-01

The point-reactor kinetics after a step reactivity insertion to a critical condition is solved directly form fission-product (FP) data (fission yields and decay data) for the first time. Numerical calculations are performed with the FP data in ENDF/B-VI. The inhour equation obtained directly from the FP data shows a different behavior at long periods from the one obtained from Tuttle's six-group parameter sets. The behavior is quite similar to the one obtained from the six-group parameter sets in ENDF/B-VI, that were obtained from FP data in a preliminary version of ENDF/B-VI. To identify the erroneous FP data, we examine the asymptotic form of the inhour equation at an infinitely long period. It is found that the most important precursors for long reactor periods are found 137 I, 88 Br and 87 Br. They cover more than 60% of the reactivity. It is remarkable that 137 I alone covers 30-50% depending on the fissioning system. In addition to the three precursors, 136 Te is found a candidate precursor for the peculiarity from the time dependence of the delayed neutron activity. It is recommended that the precision of their Pn values should be improved experimentally. For 137 I, 88 Br, and 87 Br, the relative uncertainty, dPn/Pn, should be decreased down to 2% and for 136 Te to 5%. (author)

Estimation of steady-state and transcient power distributions for the RELAP analyses of the 1963 loss-of-flow and loss-of-pressure tests at BR2

International Nuclear Information System (INIS)

Dionne, B.; Tzanos, C.P.

2011-01-01

To support the safety analyses required for the conversion of the Belgian Reactor 2 (BR2) from highly-enriched uranium (HEU) to low-enriched uranium (LEU) fuel, the simulation of a number of loss-of-flow tests, with or without loss of pressure, has been undertaken. These tests were performed at BR2 in 1963 and used instrumented fuel assemblies (FAs) with thermocouples (TC) imbedded in the cladding as well as probes to measure the FAs power on the basis of their coolant temperature rise. The availability of experimental data for these tests offers an opportunity to better establish the credibility of the RELAP5-3D model and methodology used in the conversion analysis. In order to support the HEU to LEU conversion safety analyses of the BR2 reactor, RELAP simulations of a number of loss-of-flow/loss-of-pressure tests have been undertaken. Preliminary analyses showed that the conservative power distributions used historically in the BR2 RELAP model resulted in a significant overestimation of the peak cladding temperature during the transient. Therefore, it was concluded that better estimates of the steady-state and decay power distributions were needed to accurately predict the cladding temperatures measured during the tests and establish the credibility of the RELAP model and methodology. The new approach ('best estimate' methodology) uses the MCNP5, ORIGEN-2 and BERYL codes to obtain steady-state and decay power distributions for the BR2 core during the tests A/400/1, C/600/3 and F/400/1. This methodology can be easily extended to simulate any BR2 core configuration. Comparisons with measured peak cladding temperatures showed a much better agreement when power distributions obtained with the new methodology are used.

Hybridization of Single Nanocrystals of Cs4PbBr6 and CsPbBr3

OpenAIRE

Weerd, Chris de; Lin, Junhao; Gomez, Leyre; Fujiwara, Yasufumi; Suenaga, Kazutomo; Gregorkiewicz, Tom

2017-01-01

Nanocrystals of all-inorganic cesium lead halide perovskites (CsPbX3, X = Cl, Br, I) feature high absorption and efficient narrow-band emission which renders them promising for future generation of photovoltaic and optoelectronic devices. Colloidal ensembles of these nanocrystals can be conveniently prepared by chemical synthesis. However, in the case of CsPbBr3, its synthesis can also yield nanocrystals of Cs4PbBr6 and the properties of the two are easily confused. Here, we investigate in de...

OECD-FIRE PR02. OECD-FIRE database record structure

International Nuclear Information System (INIS)

Kolar, L.

2005-12-01

In the coding guidelines, the scope, format, and details of any record required to input a real fire event at a nuclear reactor unit to the international OECD-FIRE database are described in detail. The database was set up in the OECD-FIRE-PR02 code

Development of refined MCNPX-PARET multi-channel model for transient analysis in research reactors

Energy Technology Data Exchange (ETDEWEB)

Kalcheva, S.; Koonen, E. [SCK-CEN, BR2 Reactor Dept., Boeretang 200, 2400 Mol (Belgium); Olson, A. P. [RERTR Program, Nuclear Engineering Div., Argonne National Laboratory, Cass Avenue, Argonne, IL 60439 (United States)

2012-07-01

Reactivity insertion transients are often analyzed (RELAP, PARET) using a two-channel model, representing the hot assembly with specified power distribution and an average assembly representing the remainder of the core. For the analysis of protected by the reactor safety system transients and zero reactivity feedback coefficients this approximation proves to give adequate results. However, a more refined multi-channel model representing the various assemblies, coupled through the reactivity feedback effects to the whole reactor core is needed for the analysis of unprotected transients with excluded over power and period trips. In the present paper a detailed multi-channel PARET model has been developed which describes the reactor core in different clusters representing typical BR2 fuel assemblies. The distribution of power and reactivity feedback in each cluster of the reactor core is obtained from a best-estimate MCNPX calculation using the whole core geometry model of the BR2 reactor. The sensitivity of the reactor response to power, temperature and energy distributions is studied for protected and unprotected reactivity insertion transients, with zero and non-zero reactivity feedback coefficients. The detailed multi-channel model is compared vs. simplified fewer-channel models. The sensitivities of transient characteristics derived from the different models are tested on a few reactivity insertion transients with reactivity feedback from coolant temperature and density change. (authors)

Cd4As2Br3

Directory of Open Access Journals (Sweden)

Mohammed Kars

2014-03-01

Full Text Available Single crystals of Cd4As2Br3 (tetracadmium biarsenide tribromide were grown by a chemical transport reaction. The structure is isotypic with the members of the cadmium and mercury pnictidohalides family with general formula M4A2X3 (M = Cd, Hg; A = P, As, Sb; X = Cl, Br, I and contains two independent As atoms on special positions with site symmetry -3 and two independent Cd atoms, of which one is on a special position with site symmetry -3. The Cd4As2Br3 structure consists of AsCd4 tetrahedra sharing vertices with isolated As2Cd6 octahedra that contain As–As dumbbells in the centre of the octahedron. The Br atoms are located in the voids of this three-dimensional arrangement and bridge the different polyhedra through Cd...Br contacts.

Hybrid Plasma Reactor/Filter for Transportable Collective Protection Systems

Energy Technology Data Exchange (ETDEWEB)

Josephson, Gary B.; Tonkyn, Russell G.; Frye, J. G.; Riley, Brian J.; Rappe, Kenneth G.

2011-04-06

Pacific Northwest National Laboratory (PNNL) has performed an assessment of a Hybrid Plasma/Filter system as an alternative to conventional methods for collective protection. The key premise of the hybrid system is to couple a nonthermal plasma (NTP) reactor with reactive adsorption to provide a broader envelope of protection than can be provided through a single-solution approach. The first step uses highly reactive species (e.g. oxygen radicals, hydroxyl radicals, etc.) created in a nonthermal plasma (NTP) reactor to destroy the majority (~75% - 90%) of an incoming threat. Following the NTP reactor an O3 reactor/filter uses the O3 created in the NTP reactor to further destroy the remaining organic materials. This report summarizes the laboratory development of the Hybrid Plasma Reactor/Filter to protect against a ‘worst-case’ simulant, methyl bromide (CH3Br), and presents a preliminary engineering assessment of the technology to Joint Expeditionary Collective Protection performance specifications for chemical vapor air purification technologies.

pH-oscillations in the bromate-sulfite reaction in semibatch and in gel-fed batch reactors

Science.gov (United States)

Poros, Eszter; Kurin-Csörgei, Krisztina; Szalai, István; Rábai, Gyula; Orbán, Miklós

2015-06-01

The simplest bromate oxidation based pH-oscillator, the two component BrO3--SO32- flow system was transformed to operate under semibatch and closed arrangements. The experimental preconditions of the pH-oscillations in semibatch configuration were predicted by model calculations. Using this information as guideline large amplitude (ΔpH˜3), long lasting (11-24 h) pH-oscillations accompanied with only a 20% increase of the volume in the reactor were measured when a mixture of Na2SO3 and H2SO4 was pumped into the solution of BrO3- with a very low rate. Batch-like pH-oscillations, similar in amplitude and period time appeared when the sulfite supply was substituted by its dissolution from a gel layer prepared previously in the reactor in presence of high concentration of Na2SO3. The dissolution vs time curve and the pH-oscillations in the semibatch and closed systems were successfully simulated. Due to the simplicity in composition and in experimental technique, the semibatch and batch-like BrO3--SO32- pH-oscillators may become superior to their CSTR (continuous flow stirred tank reactor) version in some present and future applications.

Electric Multipole Moments and (HyperPolarizability of X–C≡C–X, X = F, Cl, Br and I

Directory of Open Access Journals (Sweden)

Demetrios Xenides

2003-04-01

Full Text Available Abstract: We have calculated self-consistent field (SCF and second-order Møller-Plesset perturbation theory (MP2 for the dihaloethynes X–C≡C–X, X = F, Cl, Br and I. All calculations have been performed with carefully optimized, flexible basis sets of gaussiantype functions. Our best values for the quadrupole moment (Θ/ea02 are -0.6524 (FCCF, 3.6612 (ClCCCl, 5.8143 (BrCCBr and 8.3774 (ICCI. The dipole polarizability is strongly anisotropic. For the mean (α /e2a02Eh-1 and the anisotropy (Δα/e2a02Eh-1 we obtain 23.58 and 15.09 (FCCF, 51.75 and 48.30 (ClCCCl, 66.53 and 60.04 (BrCCBr, 93.79 and 78.91 (ICCI. The mean dipole hyperpolarizability (γ /e4a04Eh-3 increases rapidly as 2932 (FCCF, 9924 (ClCCCl, 17409 (BrCCBr and 35193 (ICCI. The transversal component of the hyperpolarizability is larger than the longitudinal one for FCCF, γxxxx > γzzzz but this is reversed for the other molecules in the series. Difluoroethyne is less (hyperpolarizable than ethyne.

Brændeovnes bidrag til luftforurening

DEFF Research Database (Denmark)

Pedersen, Jens Christian

2010-01-01

Brændeovnenes bidrag til luftforurening er blevet kortlagt med en hidtil uset detaljeringsgrad. Det er forskere fra Danmarks Miljøundersøgelser (DMU) på Aarhus Universitet som står bag kortlægningen. En omfattende målekampagne i Slagslunde viser at brændeovnene bidrager væsentligt til partikelfor......Brændeovnenes bidrag til luftforurening er blevet kortlagt med en hidtil uset detaljeringsgrad. Det er forskere fra Danmarks Miljøundersøgelser (DMU) på Aarhus Universitet som står bag kortlægningen. En omfattende målekampagne i Slagslunde viser at brændeovnene bidrager væsentligt til...

Emission characteristics of Xe-RbBr plasma

Science.gov (United States)

Heneral, A. A.; Avtaeva, S. V.

2017-12-01

The luminescence spectra of the longitudinal pulsed-periodic discharge in Xe-RbBr gas-vapour mixtures at low pressures are experimentally studied. Conditions for obtaining strong UV radiation of XeBr* exiplex molecules in the spectral range of 200-425 nm are found. The greatest output of the XeBr* UV radiation is provided at temperature of the gas-discharge tube walls of ~1000 K. The maximum UV emission power of the whole plasma volume is 4.8 W. Formation of XeBr* exciplex molecules in the pulsed-periodic discharge in Xe-RbBr gas-vapour mixtures at low pressures is discussed.

Free-tropospheric BrO investigations based on GOME

Science.gov (United States)

Post, P.; van Roozendael, M.; Backman, L.; Damski, J.; Thölix, L.; Fayt, C.; Taalas, P.

2003-04-01

Bromine compounds contribute significantly to the stratospheric ozone depletion. However measurements of most bromine compounds are sparse or non-existent, and experimental studies essentially rely on BrO observations. The differences between balloon and ground based measurements of stratospheric BrO columns and satellite total column measurements are too large to be explained by measurement uncertainties. Therefore, it has been assumed that there is a concentration of BrO in the free troposphere of about 1-3 ppt. In a previous work, we have calculated the tropospheric BrO abundance as the difference between total BrO and stratospheric BrO columns. The total vertical column densities of BrO are extracted from GOME measurements using IASB-BIRA algorithms. The stratospheric amount has been calculated using chemical transport models (CTM). Results from SLIMCAT and FinROSE simulations are used for this purpose. SLIMCAT is a widely used 3D CTM that has been tested against balloon measurements. FinROSE is a 3D CTM developed at FMI. We have tried several different tropospheric BrO profiles. Our results show that a profile with high BrO concentrations in the boundary layer usually gives unrealistically high tropospheric column values over areas of low albedo (like oceans). This suggests that the tropospheric BrO would be predominantly distributed in the free troposphere. In this work, attempts are made to identify the signature of a free tropospheric BrO content when comparing cloudy and non-cloudy scenes. The possible impact of orography on measured BrO columns is also investigated.

Measurement of the relative branching ratio BR(Ξc+-- >p+K- π+)/BR(Ξc+-->Ξ- π+π+)

Science.gov (United States)

FOCUS Collaboration; Link, J. M.; Reyes, M.; Yager, P. M.; Anjos, J. C.; Bediaga, I.; Göbel, C.; Magnin, J.; Massafferri, A.; de Miranda, J. M.; Pepe, I. M.; dos Reis, A. C.; Sima~o, F. R. A.; Carrillo, S.; Casimiro, E.; Sánchez-Hernández, A.; Uribe, C.; Vázquez, F.; Cinquini, L.; Cumalat, J. P.; O'Reilly, B.; Ramirez, J. E.; Vaandering, E. W.; Butler, J. N.; Cheung, H. W. K.; Gaines, I.; Garbincius, P. H.; Garren, L. A.; Gottschalk, E.; Kasper, P. H.; Kreymer, A. E.; Kutschke, R.; Bianco, S.; Fabbri, F. L.; Sarwar, S.; Zallo, A.; Cawlfield, C.; Kim, D. Y.; Rahimi, A.; Wiss, J.; Gardner, R.; Chung, Y. S.; Kang, J. S.; Ko, B. R.; Kwak, J. W.; Lee, K. B.; Park, H.; Alimonti, G.; Boschini, M.; Caccianiga, B.; D'Angelo, P.; DiCorato, M.; Dini, P.; Giammarchi, M.; Inzani, P.; Leveraro, F.; Malvezzi, S.; Menasce, D.; Mezzadri, M.; Milazzo, L.; Moroni, L.; Pedrini, D.; Pontoglio, C.; Prelz, F.; Rovere, M.; Sala, A.; Sala, S.; Davenport, T. F., III; Agostino, L.; Arena, V.; Boca, G.; Bonomi, G.; Gianini, G.; Liguori, G.; Merlo, M. M.; Pantea, D.; Ratti, S. P.; Riccardi, C.; Segoni, I.; Viola, L.; Vitulo, P.; Hernandez, H.; Lopez, A. M.; Mendez, H.; Mendez, L.; Mirles, A.; Montiel, E.; Olaya, D.; Paris, A.; Quinones, J.; Rivera, C.; Xiong, W.; Zhang, Y.; Wilson, J. R.; Cho, K.; Handler, T.; Engh, D.; Hosack, M.; Johns, W. E.; Nehring, M.; Sheldon, P. D.; Stenson, K.; Webster, M.; Sheaff, M.

2001-07-01

We report the observation of the Cabibbo suppressed decay Ξc+-->pK-π+ using data collected with the FOCUS spectrometer during the 1996-1997 Fermilab fixed target run. We find a Ξc+ signal peak of /202+/-35 events. We have measured the relative branching ratios BR(Ξ+c-->pK- π+)/BR(Ξ+c-->Ξ- π+π+)=0.234+/-0.047+/-0.022 and BR(Ξ+c-- >pK¯*(892)0)/BR(Ξ+c-->pK-π+)=0.54+/-0.09+/-0.05.

Refurbishment of BR2 (Phase 4 and 5)[1997 Scientific Report of the Belgian Nuclear Research Centre

Energy Technology Data Exchange (ETDEWEB)

Gubel, P.; Dekeyser, J.; Van der Auwera, J.

1998-07-01

The extensive refurbishment of the BR-2 materials testing reactor should allow another 10 to 15years of continued operation. The refurbishment programme is required in order to comply with modern safety standards, to enhance the reliability of operation, and to compensate for the ageing of the installations of a facility that has reached about 35 years of intensive service. The main objectives and achievements of phase 4 and 5 are described.

The genus Actiniceps Berk. & Br

NARCIS (Netherlands)

Boedijn, K.B.

1959-01-01

The genus Actiniceps Berk. & Br. is shown to be a Basidiomycete. Wiesnerina Höhn. and Dimorphocystis Corner are regarded synonymous. The type species A. thwaitesii Berk. & Br. is redescribed with D. capitatus Corner as synonym. The following new combinations are proposed: A. horrida (Höhn.) Boedijn,

Final report on in-reactor creep-fatigue deformation behaviour of a CuCrZr alloy: COFAT 2

DEFF Research Database (Denmark)

Singh, Bachu Narain; Johansen, Bjørn Sejr; Tähtinen, S.

facilities for this purpose, in-reactor creep-fatigue tests have been performed at strain amplitudes of 0.25 and 0.35 % with a holdtime of 10s in the BR-2 reactor at Mol (Belgium). These tests were performed at the ambient temperatures of 326K and 323K. For comparison purposes corresponding out...

Brûlure chez l’épileptique: brûlure pas comme les autres

Science.gov (United States)

Boukind, S.; Elatiqi, O.K.; Dlimi, M.; Elamrani, D.; Benchamkha, Y.; Ettalbi, S.

2015-01-01

Summary L’association brûlure et épilepsie est une constatation fréquente au Maroc. Ces brûlures, souvent itératives, touchent le plus souvent des femmes jeunes de milieu rural. L’accident survient habituellement au domicile, le plus souvent dans la cuisine à la suite d’une chute sur un moyen de cuisson posé au sol. Elles peuvent être inaugurales de la maladie mais surviennent plus souvent chez des patients connus mais au traitement mal suivi. Les conséquences de ces brûlures, toujours profondes, sont souvent dramatiques en termes de séquelles, chez des patients ayant déjà une insertion sociale rendue difficile par l’épilepsie. La prise en charge doit être multidisciplinaire et concerner à la fois la brûlures et l’épilepsie. Des mesures de prévention simples, visant à équilibrer l’épilepsie et éviter au patient de se trouver seul à proximité d’une source de chaleur, doivent être mises en place. PMID:27252613

In-Pile Sub-Miniature Fission Chambers Testing in BR2

Science.gov (United States)

Vermeeren, L.; Wéber, M.; Blandin, Ch.; Breaud, S.

2003-06-01

Three innovative sub-miniature fission chambers (SMFC), designed and manufactured at the Nuclear Measurement Systems Laboratory (LSMN) of CEA/Cadarache, were extensively tested in the BR2 research reactor at SCK•CEN, Mol. We present the experimental results for the (thermal) neutron sensitivity, the gamma-induced signal, the signal due to activation, the current picked up by the signal cable, the global current/voltage characteristics and the long term behaviour up to a thermal neutron fluence of 2.7·1021 n/cm2. We also compare the data with results from calculations with our FCD computer code. The onset of the saturation domain is well predicted by FCD; the neutron sensitivities can be accounted for perfectly after a refinement of the FCD model.

Reactions of N2O5 with Salty and Surfactant-Coated Glycerol: Interfacial Conversion of Br- to Br2 Mediated by Alkylammonium Cations.

Science.gov (United States)

Shaloski, Michael A; Gord, Joseph R; Staudt, Sean; Quinn, Sarah L; Bertram, Timothy H; Nathanson, Gilbert M

2017-05-18

Gas-liquid scattering and product-yield experiments are used to investigate reactions of N 2 O 5 with glycerol containing Br - and surfactant ions. N 2 O 5 oxidizes Br - to Br 2 for every solution tested: 2.7 M NaBr, 0.03 M tetrahexylammonium bromide (THABr), 0.03 M THABr + 0.5 M NaBr, 0.03 M THABr + 0.5 M NaCl, 0.03 M THABr + 0.01 M sodium dodecyl sulfate (SDS), and 0.01 M cetyltrimethylammonium bromide (CTABr). N 2 O 5 also reacts with glycerol itself to produce mono- and dinitroglycerin. Surface tension measurements indicate that 0.03 M THABr and 2.7 M NaBr have similar interfacial Br - concentrations, though their bulk Br - concentrations differ by 90-fold. We find that twice as much Br 2 is produced in the presence of THA + , implying that the conversion of Br - to Br 2 is initiated at the interface, perhaps mediated by the charged, hydrophobic pocket within the surface THA + cation. The addition of 0.5 M NaBr, 0.5 M NaCl, or 0.01 M SDS to 0.03 M THABr lowers the Br 2 production rate by 23%, 63%, and 67% of the THABr value, respectively. When CTA + is substituted for THA + , Br 2 production drops to 12% of the THABr value. The generation of Br 2 under such different conditions implies that trace amounts of surface-active alkylammonium ions can catalyze interfacial N 2 O 5 reactions, even when salts and other surfactants are present.

Size- and Wavelength-Dependent Two-Photon Absorption Cross-Section of CsPbBr3 Perovskite Quantum Dots.

Science.gov (United States)

Chen, Junsheng; Žídek, Karel; Chábera, Pavel; Liu, Dongzhou; Cheng, Pengfei; Nuuttila, Lauri; Al-Marri, Mohammed J; Lehtivuori, Heli; Messing, Maria E; Han, Keli; Zheng, Kaibo; Pullerits, Tõnu

2017-05-18

All-inorganic colloidal perovskite quantum dots (QDs) based on cesium, lead, and halide have recently emerged as promising light emitting materials. CsPbBr 3 QDs have also been demonstrated as stable two-photon-pumped lasing medium. However, the reported two photon absorption (TPA) cross sections for these QDs differ by an order of magnitude. Here we present an in-depth study of the TPA properties of CsPbBr 3 QDs with mean size ranging from 4.6 to 11.4 nm. By using femtosecond transient absorption (TA) spectroscopy we found that TPA cross section is proportional to the linear one photon absorption. The TPA cross section follows a power law dependence on QDs size with exponent 3.3 ± 0.2. The empirically obtained power-law dependence suggests that the TPA process through a virtual state populates exciton band states. The revealed power-law dependence and the understanding of TPA process are important for developing high performance nonlinear optical devices based on CsPbBr 3 nanocrystals.

Preparation and characterization of (R,S)-[76Br]BrQNB: an analogue of QNB for PET

International Nuclear Information System (INIS)

Strijckmans, V.; Loc'h, C.; Ottaviani, M.; Maziere, B.; Lee, K.S.; Zeeberg, B.R.

1997-01-01

(R,S)-[ 76 Br]BrQNB was prepared for imaging mAChR by PET . (R,S)QNB was labelled with bromine-76 by electrophilic substitution of the tributylstannyl precursor using peracetic acid as oxidizing agent. The exchange between bromine-76 and the leaving group occurred in 20 min at room temperature. A chemically and radiochemically pure product was obtained with a final radiolabelling yield of 30%. Preliminary evaluation of pharmacological properties was performed in rats. In brain, biodistribution and autoradiography studies showed that the preferential localization of (R,S)-[ 76 Br]BrQNB was m-AChR rich structures. 6 h p.i. the radioactivity uptake in the posterior cortex was 1% ID/g and the striatum to cerebellum radioactivity ratio was 13.5. Metabolite study revealed that the radiotracer remains unchanged in brain for at least 3 h. (Author)

Z-(-,-)-[76Br]BrQNP: a high affinity PET radiotracer for central and cardiac muscarinic receptors

International Nuclear Information System (INIS)

Strijckmans, V.; Coulon, C.; Loc'h, C.; Maziere, B.; Luo, H.; McPherson, D.W.; Knapp, F.F.

1996-01-01

Racemic E-1-azabicyclo[2.2.2]oct-3-yl α-(1-bromo-1-1-propen-3-yl)-α -hydroxy-α-phenylacetate (BrQNP) was prepared and evaluated in vivo as a potential candidate for imaging muscarinic acetylcholinergic receptors by Positron Emission Tomography. Initial in vivo blocking studies utilizing Z-(-,-)-[ 125 I]IQNP as a radiolabelled muscarinic probe demonstrated that a preinjection of cold E-BrQNP effectively blocks the uptake of the radiolabelled probe in the brain and heart, by 71% and 86% respectively. Z-(-,-)-[ 76 Br]BrQNP was prepared by electrophilic substitution from a tributylstannyl precursor. Peracetic acid and chloramine T was evaluated as oxidizing agents. After purification by SPE and RP-HPLC, radiolabelling yields of 85% and 95% were obtained with peracetic acid and chloramine T, respectively. The final radiochemical yield was 70% for both oxidizing agents. (author)

SV-BR-1-GM, a Clinically Effective GM-CSF-Secreting Breast Cancer Cell Line, Expresses an Immune Signature and Directly Activates CD4+ T Lymphocytes

Directory of Open Access Journals (Sweden)

Markus D. Lacher

2018-05-01

Full Text Available Targeted cancer immunotherapy with irradiated, granulocyte–macrophage colony-stimulating factor (GM-CSF-secreting, allogeneic cancer cell lines has been an effective approach to reduce tumor burden in several patients. It is generally assumed that to be effective, these cell lines need to express immunogenic antigens coexpressed in patient tumor cells, and antigen-presenting cells need to take up such antigens then present them to patient T cells. We have previously reported that, in a phase I pilot study (ClinicalTrials.gov NCT00095862, a subject with stage IV breast cancer experienced substantial regression of breast, lung, and brain lesions following inoculation with clinical formulations of SV-BR-1-GM, a GM-CSF-secreting breast tumor cell line. To identify diagnostic features permitting the prospective identification of patients likely to benefit from SV-BR-1-GM, we conducted a molecular analysis of the SV-BR-1-GM cell line and of patient-derived blood, as well as a tumor specimen. Compared to normal human breast cells, SV-BR-1-GM cells overexpress genes encoding tumor-associated antigens (TAAs such as PRAME, a cancer/testis antigen. Curiously, despite its presumptive breast epithelial origin, the cell line expresses major histocompatibility complex (MHC class II genes (HLA-DRA, HLA-DRB3, HLA-DMA, HLA-DMB, in addition to several other factors known to play immunostimulatory roles. These factors include MHC class I components (B2M, HLA-A, HLA-B, ADA (encoding adenosine deaminase, ADGRE5 (CD97, CD58 (LFA3, CD74 (encoding invariant chain and CLIP, CD83, CXCL8 (IL8, CXCL16, HLA-F, IL6, IL18, and KITLG. Moreover, both SV-BR-1-GM cells and the responding study subject carried an HLA-DRB3*02:02 allele, raising the question of whether SV-BR-1-GM cells can directly present endogenous antigens to T cells, thereby inducing a tumor-directed immune response. In support of this, SV-BR-1-GM cells (which also carry the HLA-DRB3*01:01 allele treated with

New results for the formation of a muoniated radical in the Mu + Br2 system: a van der Waals complex or evidence for vibrational bonding in Br-Mu-Br?

Science.gov (United States)

Fleming, Donald G; Cottrell, Stephen P; McKenzie, Iain; Macrae, Roderick M

2012-08-21

New evidence is presented for the observation of a muoniated radical in the Mu + Br(2) system, from μSR longitudinal field (LF) repolarisation studies in the gas phase, at Br(2) concentrations of 0.1 bar in a Br(2)/N(2) mixture at 300 K and at 10 bar total pressure. The LF repolarisation curve, up to a field of 4.5 kG, reveals two paramagnetic components, one for the Mu atom, formed promptly during the slowing-down process of the positive muon, with a known Mu hyperfine coupling constant (hfcc) of 4463 MHz, and one for a muoniated radical formed by fast Mu addition. From model fits to the Br(2)/N(2) data, the radical component is found to have an unusually high muon hfcc, assessed to be ∼3300 MHz with an overall error due to systematics expected to exceed 10%. This high muon hfcc is taken as evidence for the observation of either the Br-Mu-Br radical, and hence of vibrational bonding in this H[combining low line]-L[combining low line]-H[combining low line] system, or of a MuBr(2) van der Waals complex formed in the entrance channel. Preliminary ab initio electronic structure calculations suggest the latter is more likely but fully rigorous calculations of the effect of dynamics on the hfcc for either system have yet to be carried out.

Genomic identification and characterization of the elite strains Bradyrhizobium yuanmingense BR 3267 and Bradyrhizobium pachyrhizi BR 3262 recommended for cowpea inoculation in Brazil.

Science.gov (United States)

Leite, Jakson; Passos, Samuel Ribeiro; Simões-Araújo, Jean Luiz; Rumjanek, Norma Gouvêa; Xavier, Gustavo Ribeiro; Zilli, Jerri Édson

2017-03-31

The leguminous inoculation with nodule-inducing bacteria that perform biological nitrogen fixation is a good example of an "eco-friendly agricultural practice". Bradyrhizobium strains BR 3267 and BR 3262 are recommended for cowpea (Vigna unguiculata) inoculation in Brazil and showed remarkable responses; nevertheless neither strain was characterized at species level, which is our goal in the present work using a polyphasic approach. The strains presented the typical phenotype of Bradyrhizobium with a slow growth and a white colony on yeast extract-mannitol medium. Strain BR 3267 was more versatile in its use of carbon sources compared to BR 3262. The fatty acid composition of BR 3267 was similar to the type strain of Bradyrhizobium yuanmingense; while BR 3262 was similar to Bradyrhizobium elkanii and Bradyrhizobium pachyrhizi. Phylogenetic analyses based on 16S rRNA and three housekeeping genes placed both strains within the genus Bradyrhizobium: strain BR 3267 was closest to B. yuanmingense and BR 3262 to B. pachyrhizi. Genome average nucleotide identity and DNA-DNA reassociation confirmed the genomic identification of B. yuanmingense BR 3267 and B. pachyrhizi BR 3262. The nodC and nifH gene analyses showed that strains BR 3267 and BR 3262 hold divergent symbiotic genes. In summary, the results indicate that cowpea can establish effective symbiosis with divergent bradyrhizobia isolated from Brazilian soils. Published by Elsevier Editora Ltda.

Stig Brøgger's Artists' Books

DEFF Research Database (Denmark)

Ørum, Tania; Hvis Kromann, Thomas

Introduction and presentation of the many artist's books made by the Danish artist Stig Brøgger......Introduction and presentation of the many artist's books made by the Danish artist Stig Brøgger...

UV-Induced Anisotropy In CdBr2-CdBr2: Cu Nanostructures

Directory of Open Access Journals (Sweden)

El-Naggar A. M.

2015-09-01

Full Text Available We have found an occurrence of anisotropy in the nanostructure CdBr2-CdBr2: Cu nanocrystalline films. The film thickness was varied from 4 nm up to 80 nm. The films were prepared by successive deposition of the novel layers onto the basic nanocrystals. The detection of anisotropy was performed by occurrence of anisotropy in the polarized light at 633 nm He-Ne laser wavelength. The occurrence of anisotropy was substantially dependent on the film thickness and the photoinduced power density. Possible mechanisms of the observed phenomena are discussed.

RA Reactor applications, Annex A

International Nuclear Information System (INIS)

Martinc, R.; Cupac, S.; Stanic, A.

1990-01-01

RA reactor was not operated during the past five years due to the renewal and reconstruction of the reactor systems, which in underway. In the period from 1986-1990, reactor was operated only 144 MWh in 1986, for the need of testing the reactor systems and possibility of irradiating 125 I. Reactor will not be operated in 1991 because of the exchange of complete instrumentation which is planned to be finished by the end of 1991. It is expected to start operation in May 1992. That is why this annex includes the plan of reactor operation for period of nine months starting from from the moment of start-up. It is planned to operate the reactor at 0.02 MW power first three months, to increase the power gradually and reach 3.5 MW after 8 months of operation. It is foreseen to operate the reactor at 4.7 MW from the tenth month on [sr

pH-oscillations in the bromate–sulfite reaction in semibatch and in gel-fed batch reactors

Energy Technology Data Exchange (ETDEWEB)

Poros, Eszter; Kurin-Csörgei, Krisztina; Szalai, István; Orbán, Miklós, E-mail: orbanm@chem.elte.hu [Department of Analytical Chemistry, Institute of Chemistry, L. Eötvös University, P.O. Box 32, H-1518 Budapest 112 (Hungary); Rábai, Gyula [Institute of Physical Chemistry, University of Debrecen, P.O. Box 7, H-4010 Debrecen (Hungary)

2015-06-15

The simplest bromate oxidation based pH-oscillator, the two component BrO{sub 3}{sup −}–SO{sub 3}{sup 2–} flow system was transformed to operate under semibatch and closed arrangements. The experimental preconditions of the pH-oscillations in semibatch configuration were predicted by model calculations. Using this information as guideline large amplitude (ΔpH∼3), long lasting (11–24 h) pH-oscillations accompanied with only a 20% increase of the volume in the reactor were measured when a mixture of Na{sub 2}SO{sub 3} and H{sub 2}SO{sub 4} was pumped into the solution of BrO{sub 3}{sup −} with a very low rate. Batch-like pH-oscillations, similar in amplitude and period time appeared when the sulfite supply was substituted by its dissolution from a gel layer prepared previously in the reactor in presence of high concentration of Na{sub 2}SO{sub 3}. The dissolution vs time curve and the pH-oscillations in the semibatch and closed systems were successfully simulated. Due to the simplicity in composition and in experimental technique, the semibatch and batch-like BrO{sub 3}{sup −}–SO{sub 3}{sup 2–} pH-oscillators may become superior to their CSTR (continuous flow stirred tank reactor) version in some present and future applications.

Ductile austenitic steel for fuel cans and core components of sodium cooled reactors

International Nuclear Information System (INIS)

Schaefer, L.

1995-01-01

Two austenitic steel melts of a new composition have been studied after irradiation in the PFR fast neutron flux, in the BR2 reactor, and in the Harwell V.E. Cyclotron. The investigations were focussed on helium embrittlement and irradiation induced swelling. (orig.)

Imbedded Nanocrystals of CsPbBr3 in Cs4 PbBr6 : Kinetics, Enhanced Oscillator Strength, and Application in Light-Emitting Diodes.

Science.gov (United States)

Xu, Junwei; Huang, Wenxiao; Li, Peiyun; Onken, Drew R; Dun, Chaochao; Guo, Yang; Ucer, Kamil B; Lu, Chang; Wang, Hongzhi; Geyer, Scott M; Williams, Richard T; Carroll, David L

2017-11-01

Solution-grown films of CsPbBr 3 nanocrystals imbedded in Cs 4 PbBr 6 are incorporated as the recombination layer in light-emitting diode (LED) structures. The kinetics at high carrier density of pure (extended) CsPbBr 3 and the nanoinclusion composite are measured and analyzed, indicating second-order kinetics in extended and mainly first-order kinetics in the confined CsPbBr 3 , respectively. Analysis of absorption strength of this all-perovskite, all-inorganic imbedded nanocrystal composite relative to pure CsPbBr 3 indicates enhanced oscillator strength consistent with earlier published attribution of the sub-nanosecond exciton radiative lifetime in nanoprecipitates of CsPbBr 3 in melt-grown CsBr host crystals and CsPbBr 3 evaporated films. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High energy XeBr electric discharge laser

Science.gov (United States)

Sze, Robert C.; Scott, Peter B.

1981-01-01

A high energy XeBr laser for producing coherent radiation at 282 nm. The XeBr laser utilizes an electric discharge as the excitation source to minimize formation of molecular ions thereby minimizing absorption of laser radiation by the active medium. Additionally, HBr is used as the halogen donor which undergoes harpooning reactions with Xe.sub.M * to form XeBr*.

BrO measurements over the Eastern North-Atlantic

Directory of Open Access Journals (Sweden)

U. Platt

2009-12-01

Full Text Available The aim of the work presented here was to detect BrO in the marine boundary layer over the Eastern North-Atlantic by Multi AXis-Differential Optical Absorption Spectroscopy (MAX-DOAS of scattered sunlight. With this technique, information about the concentration and the vertical profile of trace gases in the atmosphere can be gained. BrO can be formed in the marine atmosphere by degradation of biogenic organohalogens or by oxidation of bromide in sea salt aerosol. BrO influences the chemistry in marine air in many ways, e.g. since it catalytically destroys ozone, changes the NO₂/NO-ratio as well as the OH/HO₂-ratio and oxidises DMS. However, the abundance and the significance of BrO in the marine atmosphere is not yet fully understood. <br>> We report on data collected during a ship cruise, which took place along the West African Coast in February 2007, within the framework of the Surface Ocean PRocesses in the ANthropocene project (SOPRAN. Tropospheric BrO could be detected during this cruise at peak mixing ratios of (10.2±3.7 ppt at an assumed layer height of 1 km on 18 February 2007. Furthermore, it was found that the mean BrO concentrations increased when cruising close to the African Coast suggesting that at least part of the BrO might have originated from there.

The dynamics of the Hg + Br2 reaction: elucidation of the reaction mechanism for the Br exchange reaction.

Science.gov (United States)

Jambrina, P G; Menéndez, M; Aoiz, F J

2017-06-28

In spite of its importance in the Hg atmospheric chemistry, the dynamics of the Hg + Br 2 → HgBr + Br reaction is poorly understood. In this article, we have carried out a comprehensive study of the reaction mechanism of this reaction by means of quasiclassical trajectories (QCTs) on an existing ab initio potential energy surface (PES). The reaction has a non trivial dynamics, as a consequence of its large endothermicity, the presence of a deep potential well, and the competition between the Br exchange and the collision induced dissociation processes. Our calculations demonstrate that insertion is only relevant at energies just above the reaction threshold and that, at energies above 2.3 eV, HgBr formation typically takes place via a sort of frustrated dissociation. In order to compare directly with the results obtained in extensive cross molecular beam experiments for the homologous reaction with I 2 , angular distributions in the laboratory frame for Hg + Br 2 have been simulated under similar experimental conditions. The lack of agreement at the highest energies considered suggests that either the two reactions have substantially different mechanisms or that calculations on a single PES cannot account for the dynamics at those energies.

Rashba split surface states in BiTeBr

International Nuclear Information System (INIS)

Eremeev, S V; Rusinov, I P; Nechaev, I A; Chulkov, E V

2013-01-01

Within density functional theory, we study the bulk band structure and surface states of BiTeBr. We consider both ordered and disordered phases, which differ in atomic order in the Te–Br sublattice. On the basis of relativistic ab initio calculations, we show that the ordered BiTeBr is energetically preferable as compared with the disordered one. We demonstrate that both Te- and Br-terminated surfaces of the ordered BiTeBr hold surface states with a giant spin–orbit splitting. The Te-terminated surface-state spin splitting has Rashba-type behavior with the coupling parameter α R ∼ 2 eVÅ. (paper)

Nuclear reactor control with fuzzy logic approaches - strengths, weakness, opportunities, and threats

International Nuclear Information System (INIS)

Ruan, Da

2004-01-01

As part of the special track on 'Lessons learned from computational intelligence in nuclear applications' at the forthcoming FLINS 2004 conference on Applied Computational Intelligence (Blankenberge, Belgium, September 1-3, 2004), research experiences on fuzzy logic techniques in applications of nuclear reactor control operation are critically reviewed in this presentation. Assessment of four real fuzzy control applications at the MIT research reactor in the US, the FUGEN heavy water reactor in Japan, the BR1 research reactor in Belgium, and a TRIGA Mark III reactor in Mexico will be examined thought a SWOT analysis (strengths, weakness, opportunities, and threats). Special attention will be paid to the current cooperation between the Belgian Nuclear Research Centre (SCK-CEN) and the Mexican Nuclear Centre (ININ) on the fuzzy logic control for nuclear reactor control project under the partial support of the National Council for Science and Technology of Mexico (CONACYT). (Author)

Brominated methanes as photoresponsive molecular storage of elemental Br2.

Science.gov (United States)

Kawakami, Kazumitsu; Tsuda, Akihiko

2012-10-01

The photochemical generation of elemental Br(2) from brominated methanes is reported. Br(2) was generated by the vaporization of carbon oxides and HBr through oxidative photodecomposition of brominated methanes under a 20 W low-pressure mercury lamp, wherein the amount and situations of Br(2) generation were photochemically controllable. Liquid CH(2)Br(2) can be used not only as an organic solvent but also for the photoresponsive molecular storage of Br(2), which is of great technical benefit in a variety of organic syntheses and in materials science. By taking advantage of the in situ generation of Br(2) from the organic solvent itself, many organobromine compounds were synthesized in high practical yields with or without the addition of a catalyst. Herein, Br(2) that was generated by the photodecomposition of CH(2)Br(2) retained its reactivity in solution to undergo essentially the same reactions as those that were carried out with solutions of Br(2) dissolved in CH(2)Br(2) that were prepared without photoirradiation. Furthermore, HBr, which was generated during the course of the photodecomposition of CH(2)Br(2), was also available for the substitution of the OH group for the Br group and for the preparation of the HBr salts of amines. Furthermore, the photochemical generation of Br(2) from CH(2)Br(2) was available for the area-selective photochemical bleaching of natural colored plants, such as red rose petals, wherein Br(2) that was generated photochemically from CH(2)Br(2) was painted onto the petal to cause radical oxidations of the chromophoric anthocyanin molecules. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Zn2(TeO3Br2

Directory of Open Access Journals (Sweden)

Mats Johnsson

2008-05-01

Full Text Available Single crystals of dizinc tellurium dibromide trioxide, Zn2(TeO3Br2, were synthesized via a transport reaction in sealed evacuated silica tubes. The compound has a layered crystal structure in which the building units are [ZnO4Br] distorted square pyramids, [ZnO2Br2] distorted tetrahedra, and [TeO3E] tetrahedra (E being the 5s2 lone pair of Te4+ joined through sharing of edges and corners to form layers of no net charge. Bromine atoms and tellurium lone pairs protrude from the surfaces of each layer towards adjacent layers. This new compound Zn2(TeO3Br2 is isostructural with the synthetic compounds Zn2(TeO3Cl2, CuZn(TeO32, Co2(TeO3Br2 and the mineral sophiite, Zn2(SeO3Cl2.

On the electrodeposition of /sup 80m/Br, /sup 80/Br and /sup 82/Br species from (eta, gamma) activated dibromoethane - N,N-dimethyl aniline mixture

International Nuclear Information System (INIS)

Zaman, M.R.

1997-01-01

Thermal neutron activation have been carried out in dibromomethane (DBM)-n,n-dimethyl aniline (N,N-DMA) system and the /sup 80m/Br, /sup 82/Br species have been electrodeposited on Ag/AgBr electrodes under a constant electric field of 175 volts cm/sup -1/. With the addition of N,N-DMA, anodic deposition has been severely decreased for all the radiobromines and cathode plate shows zero activities. Results are critically discussed by explaining the chemical reactivity of the amine. Electrode deposition pattern and the chemical stabilization mode of the nucleogenic bromine species in this system are deduced to some extents. (author)

Analysis of cofrentes abnormal plant transients with RETRAN-02 and RETRAN-03

International Nuclear Information System (INIS)

Mata, P.; Sedano, P.G.; Serra, J.

1992-01-01

In this paper the applicability and usefulness of a complete and well-qualified plant transient code and model to support in-depth evaluation of anomalous plant transients are described. The qualified best-estimate RETRAN-02 model for the Cofrentes nuclear power plant (a boiling water reactor with an uprated power of 2952 MW) has been updated for RETRAN-03 using algebraic slip and one-dimensional kinetics. This model has been used in the analysis of recent abnormal plant transients at Cofrentes, including a partial control rod insertion at 92% power, a turbine trip at 67% power with reactor vessel overfill, and reactor instabilities during startup

Solution-Grown CsPbBr3 /Cs4 PbBr6 Perovskite Nanocomposites: Toward Temperature-Insensitive Optical Gain.

Science.gov (United States)

Wang, Yue; Yu, Dejian; Wang, Zeng; Li, Xiaoming; Chen, Xiaoxuan; Nalla, Venkatram; Zeng, Haibo; Sun, Handong

2017-09-01

With regards to developing miniaturized coherent light sources, the temperature-insensitivity in gain spectrum and threshold is highly desirable. Quantum dots (QDs) are predicted to possess a temperature-insensitive threshold by virtue of the separated electronic states; however, it is never observed in colloidal QDs due to the poor thermal stability. Besides, for the classical II-VI QDs, the gain profile generally redshifts with increasing temperature, plaguing the device chromaticity. Herein, this paper addresses the above two issues simultaneously by embedding ligands-free CsPbBr 3 nanocrystals in a wider band gap Cs 4 PbBr 6 matrix by solution-phase synthesis. The unique electronic structures of CsPbBr 3 nanocrystals enable temperature-insensitive gain spectrum while the lack of ligands and protection from Cs 4 PbBr 6 matrix ensure the thermal stability and high temperature operation. Specifically, a color drift-free stimulated emission irrespective of temperature change (20-150 °C) upon two-photon pumping is presented and the characteristic temperature is determined to be as high as ≈260 K. The superior gain properties of the CsPbBr 3 /Cs 4 PbBr 6 perovskite nanocomposites are directly validated by a vertical cavity surface emitting laser operating at temperature as high as 100 °C. The results shed light on manipulating optical gain from the advantageous CsPbBr 3 nanocrystals and represent a significant step toward the temperature-insensitive frequency-upconverted lasers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Irradiation data analysis and thermal analysis of the 02M-02K capsule for material irradiation test

International Nuclear Information System (INIS)

Choi, Myoung Hwan; Choo, K. N.; Kang, Y. H.; Kim, B. G.; Cho, M. S.; Sohn, J. M.; Shin, Y. T.; Park, S. J.; Kim, Y. J.

2004-11-01

In order to evaluate the fracture toughness of RPV materials, the material irradiation test using the instrumented capsule (02M-02K) were carried out in the HANARO in August 2003. Based on the user's requirements the thermal design analysis of the capsule 02M-02K was performed, and the specimens were suitably arranged in each step of the capsule main body. In this report, both the temperature data of specimens measured during irradiation test and the calculated data from the thermal analysis are compared and evaluated. Also, the temperature profile in each step with the HANARO reactor power and helium pressure is reviewed and evaluated. The effects of the gap size such as theoretically calculated from thermal expansion during irradiation test and measured one in the manufacturing of the capsule on the specimen temperature were reviewed. The thermal analysis was performed by using a Finite Element (FE) analysis program, ANSYS. Two-dimensional model for the 1/4 section of the capsule is generated, and the γ-heating rate of the materials used in the capsule at the control rod position of 430 mm is used as input data. The thermal analysis using a 3-dimensional model, which is quite similar to the actual shape of the capsule, is also conducted to obtain the temperature distribution in the axial direction. The analysis results show that the temperature difference between the top and bottom positions of a specimen is found to be smaller than 13.2 .deg. C. The maximum measured and calculated temperature in the step 3 of the capsule is 256 .deg. C and 264 .deg. C, respectively. The measured temperature data are obtained at the reactor power of 24 MW, the heater power of 0 W and the helium pressure of 760 torr. Generally, the temperature data obtained by the FE analysis are slightly lower than those of the measured except the step 1 of the capsule. However, the temperature difference between the measured and the calculated shows a good agreement within 9 percent. It is

Performance of LiAlloy/Ag(2)CrO(4) Couples in Molten CsBr-LiBr-KBr Eutectic

International Nuclear Information System (INIS)

GUIDOTTI, RONALD A.; REINHARDT, FREDERICK W.

1999-01-01

The performance of Li-alloy/CsBr-LiBr-KBr/Ag(sub 2)CrO(sub 4) systems was studied over a temperature range of 250 C to 300 C, for possible use as a power source for geothermal borehole applications. Single cells were discharged at current densities of 15.8 and 32.6 mA/cm(sup 2) using Li-Si and Li-Al anodes. When tested in 5-cell batteries, the Li-Si/CsBr-LiBr-KBr/Ag(sub 2)CrO(sub 4) system exhibited thermal runaway. Thermal analytical tests showed that the Ag(sub 2)CrO(sub 4) cathode reacted exothermically with the electrolyte on activation. Consequently, this system would not be practical for the envisioned geothermal borehole applications

Structure and luminescence of α and β ThBr4: optical properties of U4+ in α ThBr4

International Nuclear Information System (INIS)

Simoni, E.

1988-05-01

The aim of this work is to understand the comparative structural and intrinsic luminescence properties of the pure matrices α and β - ThBr 4 , and to study the electronic structure by optical spectroscopy of the U 4+ ion in the α-ThBr 4 matrix. 1)Under U.V. excitation, βThBr 4 is intensively fluorescent in the blue-purple and α-ThBr 4 is fluorescent in the red. The main results concerning β-ThBr 4 are the following: -the optical absorption in the U.V. is under the form of a sudden absorption front and for a same temperature, its threshold energy has the same value as the threshold energy of the excitation function and of the photocurrent peak; -the intensity and the life time of the emission decrease when the temperature increases from 300 K until 400 K ( extinction temperature). All the obtained results have been explained either with the molecular orbitals levels of the ThBr 8 4- cluster or with the valence and conduction bands of the pure matrix. 2)The absorption and emission spectra of U 4+ in α-ThBr 4 (in which U 4+ has a point symmetry S 4 ) obtained between 300 K and 4.2 K have allowed to index 30 levels. The calculation of the spectroscopic parameters F k , ξ and B k q has been carried out in symmetry D 2d and S 4 . The comparison of these parameters with those calculated for U 4+ in β-ThBr 4 and β-ThCl 4 show that the global force of the crystalline field is practically the same in the three matrices, but that the structure transformation β→α occurs more on the values of these B k q than on the change of the ligands Br - →Cl - . On the other hand, it has been possible with the α-ThBr 4 matrix, or the β-ThBr 4 and the β-ThCl 4 , to observe the fluorescence spectra of the U 4+ ion (particularly weak phonons energies). (O.M.)

Chemical consequences of radioactive decay. 1. Study of 249Cf ingrowth into crystalline 249BkBr3: a new crystalline phase of CfBr3

International Nuclear Information System (INIS)

Young, J.P.; Haire, R.G.; Peterson, J.R.; Ensor, D.D.; Fellows, R.L.

1980-01-01

Spectrophotometric and x-ray powder diffraction methods have been applied to a study of the ingrowth of californium-249 by β - decay of berkelium-249 in crystalline 249 BkBr 3 . It was found that the Cf daughter grows in with the same oxidation state and crystal structure as the parent. Thus, six-coordinate BkBr 3 (AlCl 3 -type monoclinic structure) generates six-coordinate CfBr 3 , and eight-coordinate BkBr 3 (PuBr 3 -type orthorhombic structure) generates eight-coordinate CfBr 3 , a previously unknown form of CfBr 3 . It was also found that the daughter Cf(III) in the BkBr 3 parent compound can be reduced to Cf(II) by treatment with H 2 , as it can in pure CfBr 3 . 5 figures

Zn2(TeO3)Br2

Science.gov (United States)

Zhang, Dong; Johnsson, Mats

2008-01-01

Single crystals of dizinc tellurium dibromide trioxide, Zn2(TeO3)Br2, were synthesized via a transport reaction in sealed evacuated silica tubes. The compound has a layered crystal structure in which the building units are [ZnO4Br] distorted square pyramids, [ZnO2Br2] distorted tetra­hedra, and [TeO3 E] tetra­hedra (E being the 5s 2 lone pair of Te4+) joined through sharing of edges and corners to form layers of no net charge. Bromine atoms and tellurium lone pairs protrude from the surfaces of each layer towards adjacent layers. This new compound Zn2(TeO3)Br2 is isostructural with the synthetic compounds Zn2(TeO3)Cl2, CuZn(TeO3)2, Co2(TeO3)Br2 and the mineral sophiite, Zn2(SeO3)Cl2. PMID:21202162

Synthesis and Biological Evaluation of (S)-Amino-2-methyl-4-[(76)Br]bromo-3-(E)-butenoic Acid (BrVAIB) for Brain Tumor Imaging.

Science.gov (United States)

Burkemper, Jennifer L; Huang, Chaofeng; Li, Aixiao; Yuan, Liya; Rich, Keith; McConathy, Jonathan; Lapi, Suzanne E

2015-11-12

The novel compound, (S)-amino-2-methyl-4-[(76)Br]bromo-3-(E)-butenoic acid (BrVAIB, [(76)Br]5), was characterized against the known system A tracer, IVAIB ([(123)I]8). [(76)Br]5 was prepared in a 51% ± 19% radiochemical yield with high radiochemical purity (≥98%). The biological properties of [(76)Br]5 were compared with those of [(123)I]8. Results showed that [(76)Br]5 undergoes mixed amino acid transport by system A and system L transport, while [(123)I]8 had less uptake by system L. [(76)Br]5 demonstrated higher uptake than [(123)I]8 in DBT tumors 1 h after injection (3.7 ± 0.4% ID/g vs 1.5 ± 0.3% ID/g) and also showed higher uptake vs [(123)I]8 in normal brain. Small animal PET studies with [(76)Br]5 demonstrated good tumor visualization of intracranial DBTs up to 24 h with clearance from normal tissues. These results indicate that [(76)Br]5 is a promising PET tracer for brain tumor imaging and lead compound for a mixed system A and system L transport substrate.

Synthesis and structure of [(NH2)2CSSC(NH2)2]2[OsBr6]Br2 . 3H2O

International Nuclear Information System (INIS)

Rudnitskaya, O. V.; Kultyshkina, E. K.; Stash, A. I.; Glukhova, A. A.; Venskovskii, N. U.

2008-01-01

The complex [(NH 2 ) 2 CSSC(NH 2 ) 2 ] 2 [OsBr 6 ]Br 2 . 3H 2 O is synthesized by the reaction of K 2 OsBr 6 with thiocarbamide in concentrated HBr and characterized using electronic absorption and IR absorption spectroscopy. Its crystal structure is determined by X-ray diffraction. The crystals are orthorhombic, a = 11.730(2) A, b = 14.052(3) A, c = 16.994(3) A, space group Cmcm, and Z = 4. The [OsBr 6 ] 2- anionic complex has an octahedral structure. The Os-Br distances fall in the range 2.483-2.490 A. The α,α'-dithiobisformamidinium cation is a product of the oxidation of thiocarbamide. The S-S and C-S distances are 2.016 and 1.784 A, respectively. The H 2 O molecules, Br - ions, and NH 2 groups of the cation are linked by hydrogen bonds.

Decision, Annex 3[Organizational structure of the Division for reactor maintenance]; Prilog br. 3, Odluka

Energy Technology Data Exchange (ETDEWEB)

Pavicevic, M [Reaktor RA, Odelenje odrzavanja, Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1965-12-15

The objective of the decision about the change in the organizational scheme of the Division for RA reactor maintenance is to achieve efficiency. The tasks are precisely defined as to divide the maintenance and repair tasks from special ones related to improvement of reactor operation its applicability. [Serbo-Croat] U cilju poboljsanja organizacije rada Odelenja odrzavanja reaktora RA, kao i efikasnijeg koriscenja raspolozivog kadra izvrsice se razgranicenje poslova odrzavanja i remonta od posebnih zadataka koji se odnose na poboljsanje rada reaktora i povecanje njegovih mogucnosti.

Molecular characterization of BrMYB28 and BrMYB29 paralogous transcription factors involved in the regulation of aliphatic glucosinolate profiles in Brassica rapa ssp. pekinensis.

Science.gov (United States)

Baskar, Venkidasamy; Park, Se Won

2015-07-01

Glucosinolates (GSL) are one of the major secondary metabolites of the Brassicaceae family. In the present study, we aim at characterizing the multiple paralogs of aliphatic GSL regulators, such as BrMYB28 and BrMYB29 genes in Brassica rapa ssp. pekinensis, by quantitative real-time PCR (qRT-PCR) analysis in different tissues and at various developmental stages. An overlapping gene expression pattern between the BrMYBs as well as their downstream genes (DSGs) was found at different developmental stages. Among the BrMYB28 and BrMYB29 paralogous genes, the BrMYB28.3 and BrMYB29.1 genes were dominantly expressed in most of the developmental stages, compared to the other paralogs of the BrMYB genes. Furthermore, the differential expression pattern of the BrMYBs was observed under various stress treatments. Interestingly, BrMYB28.2 showed the least expression in most developmental stages, while its expression was remarkably high in different stress conditions. More specifically, the BrMYB28.2, BrMYB28.3, and BrMYB29.1 genes were highly responsive to various abiotic and biotic stresses, further indicating their possible role in stress tolerance. Moreover, the in silico cis motif analysis in the upstream regulatory regions of BrMYBs showed the presence of various putative stress-specific motifs, which further indicated their responsiveness to biotic and abiotic stresses. These observations suggest that the dominantly expressed BrMYBs, both in different developmental stages and under various stress treatments (BrMYB28.3 and BrMYB29.1), may be potential candidate genes for altering the GSL level through genetic modification studies in B. rapa ssp. pekinensis. Copyright © 2015. Published by Elsevier SAS.

Theoretical study and rate constant calculation for the reactions of SH (SD) with Cl2, Br2, and BrCl.

Science.gov (United States)

Wang, Li; Liu, Jing-Yao; Li, Ze-Sheng; Sun, Chia-Chung

2005-01-30

The mechanisms of the SH (SD) radicals with Cl2 (R1), Br2 (R2), and BrCl (R3) are investigated theoretically, and the rate constants are calculated using a dual-level direct dynamics method. The optimized geometries and frequencies of the stationary points are calculated at the MP2/6-311G(d,p) and MPW1K/6-311G(d,p) levels. Higher-level energies are obtained at the approximate QCISD(T)/6-311++G(3df, 2pd) level using the MP2 geometries as well as by the multicoefficient correlation method based on QCISD (MC-QCISD) using the MPW1K geometries. Complexes with energies less than those of the reactants or products are located at the entrance or the exit channels of these reactions, which indicate that the reactions may proceed via an indirect mechanism. The enthalpies of formation for the species XSH/XSD (X = Cl and Br) are evaluated using hydrogenation working reactions method. By canonical variational transition-state theory (CVT), the rate constants of SH and SD radicals with Cl2, Br2, and BrCl are calculated over a wide temperature range of 200-2000 K at the a-QCISD(T)/6-311++G(3df, 2pd)//MP2/6-311G(d, p) level. Good agreement between the calculated and experimental rate constants is obtained in the measured temperature range. Our calculations show that for SH (SD) + BrCl reaction bromine abstraction (R3a or R3a') leading to the formation of BrSH (BrSD) + Cl in a barrierless process dominants the reaction with the branching ratios for channels 3a and 3a' of 99% at 298 K, which is quite different from the experimental result of k3a'/k3' = 54 +/- 10%. Negative activation energies are found at the higher level for the SH + Br2 and SH + BrCl (Br-abstraction) reactions; as a result, the rate constants show a slightly negative temperature dependence, which is consistent with the determination in the literature. The kinetic isotope effects for the three reactions are "inverse". The values of kH/kD are 0.88, 0.91, and 0.69 at room temperature, respectively, and they increase

Ab Initio Potential Energy Surfaces for Both the Ground (X̃1A′ and Excited (A∼1A′′ Electronic States of HSiBr and the Absorption and Emission Spectra of HSiBr/DSiBr

Directory of Open Access Journals (Sweden)

Anyang Li

2012-01-01

Full Text Available Ab initio potential energy surfaces for the ground (X̃1A′ and excited (A˜A′′1 electronic states of HSiBr were obtained by using the single and double excitation coupled-cluster theory with a noniterative perturbation treatment of triple excitations and the multireference configuration interaction with Davidson correction, respectively, employing an augmented correlation-consistent polarized valence quadruple zeta basis set. The calculated vibrational energy levels of HSiBr and DSiBr of the ground and excited electronic states are in excellent agreement with the available experimental band origins. In addition, the absorption and emission spectra of HSiBr and DSiBr were calculated using an efficient single Lanczos propagation method and are in good agreement with the available experimental observations.

Experimental Conditions: SE3_S02_M02_D02 [Metabolonote[Archive

Lifescience Database Archive (English)

Full Text Available SE3_S02_M02_D02 SE3 Comparison of fruit metabolites among tomato varieties 1 SE3_S0...2 Solanum lycopersicum House Momotaro fruit SE3_S02_M02 6.7 mg [MassBase ID] MDLC1_25530 SE3_MS1 LC-FT-ICR-M

The first university research reactor in India

International Nuclear Information System (INIS)

Murthy, G.S.

1999-01-01

At low power research reactor is being set up in Andhra University to cater to the needs of researchers and isotope users by the Department of Atomic Energy in collaboration with Andhra University. This reactor is expected to be commissioned by 2001-02. Departments like Chemistry, Earth Sciences, Physics, Life Sciences, Pharmacy, Medicine and Engineering would be the beneficiaries of the availability of this reactor. In this paper, details of the envisaged research programme and training activities are discussed. (author)

Light-emitting diodes based on two-dimensional PA2(CsPbBr3)n-1PbBr4 layered perovskites%基于PA2(CsPbBr3)n-1PbBr4二维层状钙钛矿的电致发光二极管

Institute of Scientific and Technical Information of China (English)

孟妍; 牛连斌; 许龙; 林春燕; 熊自阳; 熊祖洪; 陈平

2018-01-01

进一步提高全无机卤铅钙钛矿材料CsPbBr3的发光效率,对制备高效率、高稳定性的电致发光二极管(PeLED)具有重要意义.制备纳米级的钙钛矿量子点,一方面有助于提高激子的束缚能和钙钛矿晶体的荧光效率,另一方面也有利于形成连续、致密的二维层状钙钛矿薄膜.本文采用“原位生长”的策略,将一种具有长链结构的丙基溴化胺(CH3CH2CH2NH3Br,PABr)作为添加剂,与CsPbBr3的前驱体溶液进行共混,得到PA2(CsPbBr3)n-1PbBr4钙钛矿量子点.形成的二维层状钙钛矿薄膜均匀致密,在光致发光条件下,呈现出明亮的蓝绿光发射(发光峰位于506 nm).在电致发光方面,基于PA2(CsPbBr3)n-1PbBr4的PeLED启亮电压为～4.2 V,最大亮度为～2370 cd/m2,最高电流效率为～1.06 cd/A,最高EQE为～0.57％.相较于传统方法,本工作在制作工艺、成膜质量以及PeLED的发光效率有了显著的提升,为将来进一步探索低成本、高效率的蓝光PeLEDs提供了一种可行的思路.%Solution-processed organometal halide perovskites (formulated as ABX3,where A is the methylammonium (CH3NH3+)(MA) or metal cesium cation (Cs+),B is the lead cation (Pb2+) and X is the halide anion (Br-,I-,Cl-)) are promising candidates for next generation light-emitting materials owing to their unique optoelectronic properties.These properties mainly include extremely high photoluminescence quantum yield (PLQY),easily tunable band gap and narrow emission characteristics.During the past two years,impressive progresses have been made in perovskite light-emitting diodes (PeLED) with hybrid organic-inorganic perovskite materials (i.e.,CH3NH3PbBr3).So far,the best external quantum efficiency (EQE) of CH3NH3PbBr3-based PeLED was reaching up to ～8.53％ which was close to the results of organic light-emitting diodes (OLED).Despite the remarkable performance of the devices demonstrated,the stability of organic-inorganic hybrid perovskites

Results of K_oo measurements of HTGR lattice by oscillated zero reactivity technique using the AGIP-NUCLEARE RB-2 reactor

Energy Technology Data Exchange (ETDEWEB)

Benedetti, F; Brighenti, G.; Chiodi, P. L.; Ghilardotti, G.; Giuliani, C.

1974-10-15

This paper describes k-infinity measurements conducted using an assembly of loose HTGR coated particles in the BR-2 reactor by means of null reactivity oscillating method comparing the effect of poisoned and unpoisoned lattices like tests performed in the Physical Constants Test Reactor (PCTR) at Hanford. The RB-2 reactor was the property of the Italian firm AGIP NUCLEARE and operated at the Montecuccolino Center in Bologna.

Comparative study of α and β-ThBr4: structure and luminescence. Spectroscopy of U4+ in α-ThBr4

International Nuclear Information System (INIS)

Simoni, E.

1988-05-01

UV absorption of β-ThBr 4 : presents a plain absorption front and for the same temperature the threshold energy has the same value than the threshold energy of excitation function and photocurrent peak. Emission intensity and lifetime decrease when temperature increases from 300 K to 400K (extinction temperature). Results are interpreted either by molecular orbital levels of the ThBr 8 4- cluster or either by conduction and valence bands of the matrix above. Absorption and emission spectra of U 4+ in α-ThBr 4 (where U 4+ has a S 4 symmetry) between 300 K and 4.2 K allow indexation of 30 levels. Spectroscopic parameters are calculated in D 2d and S 4 symmetry. Comparison of these parameters with those of U 4+ in β-ThBr 4 and β-ThCl 4 shows that crystal field force is practically the same in the three matrices but the structure transformation from β to α has more influence on B q k than ligand change from Br - to Cl - . Owing to very low phonon energy, fluorescence spectra of U 4+ is easy to observe in α-ThBr 4 as it is in β-ThBr 4 and ThCl 4 [fr

Possible physics modifications to CIRUS reactor core for improved reactor utilization

International Nuclear Information System (INIS)

John, Benjamin; Khosla, S.K.; Narain, Rajendra.

1976-01-01

Two fuelling schemes for uprating the neutron flux in CIRUS reactor at Trombay, are studied. One scheme employs enriched uranium-aluminium alloy boosters, the second envisages employing thorium oxide enriched with 0.2% plutonium oxide. It is seen that the second scheme has the potential of in-situ thorium utilization. (M.G.B.)

Corrosion effect of fast reactor fuel claddings on their mechanical properties

International Nuclear Information System (INIS)

Davydov, E.F.; Krykov, F.N.; Shamardin, V.K.

1985-01-01

Fast reactor fuel cladding corrosion effect on its mechanical properties was investigated. UO 2 fuel elements were irradiated in the BOP-60 reactor at the linear heat rate of 42 kw/m. Fuel cladding is made of stainless steel OKh16N15M3BR. Calculated maximum cladding temperature is 920 K. Neutron fluence in the central part of fuel elements is 6.3x10 26 m+H- 2 . To investigate the strength changes temperature dependence of corrossion depth, cladding strength reduction factors was determined. Samples plasticity reduction with corrosion layer increase is considered to be a characteristic feature

NY-BR-1 Antigen Expression and anti-NY-BR-1 IgG in Egyptian Breast Cancer Patients: Clinicopathological and Prognostic Significance.

Science.gov (United States)

Abu El-Nazar, Salma Y; Ghazy, Amany A; Ghoneim, Hossam E; Zoheir, Malak; Ahmed, Ahmed S; Sorour, Sally S; Abouelella, Amira M

2015-01-01

Breast cancer is the most common gynecological malignancy in the world. In Egypt, it ranks the first among female malignancies with incidence of 37.7%. Over the last decades, the integration of prognostic and predictive markers in treatment decisions has led to more individualized and optimized therapy. NY-BR-1 antigen has been shown to be frequently expressed in breast cancers. The study aimed to assess the tissue expression of NY-BR-1 antigen and serum IgG antibody to this antigen in Egyptian breast cancer females. The study was conducted on 60 females (10 healthy, 10 having benign breast lesions, 40 with malignant breast cancer). NY-BR-1 Ag expression was evaluated by immunohistochemistry and anti-NY-BR-1 IgG was assessed by ELISA. Results revealed a significant difference in NY-BR-1 Ag expression between benign and malignant breast cancer patients. There was a significant correlation between NY-BR-1 antigen expression and estrogen receptor's status (P = 0.019), stage of the disease (P = 0.008), menopausal status (P = 0.008), lymph node involvement (P = 0.022) and anti-NY-BR-1 IgG (P = 0.032) among the studied individuals. In addition, there was a statistically significant increase in anti-NY-BR-1 IgG O.D. results among malignant breast cancer group. It is correlated with tumor type (P < 0.001) and progesterone receptor status (P = 0.038). In conclusion, our work may represent a step towards identification of a new prognostic marker specific for breast cancer.

Renewable energy in focus: In5Se5Br, a solid material with promising thermoelectric properties for industrial applications

International Nuclear Information System (INIS)

Xhaxhiu, Kledi; Kvarnström, Carita; Damlin, Pia; Bente, Klaus

2014-01-01

Highlights: • In 5 Se 5 Br contains indium simultaneously in three different oxidation states. • Bulk sample of In 5 Se 5 Br shows n-type conductivity. • The Seebeck voltage increases linearly with the temperature difference increase. • In bulk In 5 Se 5 Br the resistivity oscillates between 2.6 MΩ and 23 MΩ. • DTA and HT-powder XRD data show incongruent melting of the compound. - Abstract: We obtained via solid state synthesis needle-shaped crystals of In 5 Se 5 Br crystallizing in the space group Pmn2 1 and containing indium simultaneously in three different oxidation states: In + , formal In 2+ and In 3+ . Bulk sample of In 5 Se 5 Br shows n-type conductivity and linear increase of Seebeck voltage with the temperature difference increase. Seebeck voltage of approx. 720 mV is recorded at a temperature difference of 80 K, corresponding to a Seebeck coefficient −8900 μV/K. A voltage increase up to 250 mV is recorded within 10 min upon application of a 27 K temperature difference between the contacts. On-off switching of the heating source unveils repeatable results. Linear I–U behavior with a resistivity of 2.32 × 10 11 Ω is observable for individual needles of In 5 Se 5 Br. In bulk In 5 Se 5 Br the resistivity oscillates between 2.6 MΩ and 23 MΩ. DTA and HT-powder XRD data show incongruent melting to InBr, InSe and In 2 Se 3 at 805 K. The ternary compound expands 1.02% along [0 1 0] showing a coefficient of thermal expansion α b = 2.3(4) × 10 −5 K −1 . Lower expansions of 0.6% and 0.16% along a and c axes corresponding to mean coefficients of thermal expansion of α a ¯ = 1.3(1) × 10 −5 K −1 , α c ¯ = 4.4(5) × 10 −6 K −1 are observed. Thin layer growing of In 5 Se 5 Br on glass substrate with targeted doping/substitutions can improve the sample conductivity, increase the Seebeck coefficient and lower the thermal conductivity making In 5 Se 5 Br a good alternative material for industrial thermoelectric applications

Digital control system of advanced reactor

International Nuclear Information System (INIS)

Peng Huaqing; Zhang Rui; Liu Lixin

2001-01-01

This article produced the Digital Control System For Advanced Reactor made by NPIC. This system uses Siemens SIMATIC PCS 7 process control system and includes five control system: reactor power control system, pressurizer level control system, pressurizer pressure control system, steam generator water level control system and dump control system. This system uses three automatic station to realize the function of five control system. Because the safety requisition of reactor is very strict, the system is redundant. The system configuration uses CFC and SCL. the human-machine interface is configured by Wincc. Finally the system passed the test of simulation by using RETRAN 02 to simulate the control object. The research solved the key technology of digital control system of reactor and will be very helpful for the nationalization of digital reactor control system

The development of the gas cooled fast breeder reactor

International Nuclear Information System (INIS)

Dalle Donne, M.; Kernforschungszentrum Karlsruhe

1975-01-01

A survey of the present technological state is given on the basis of the developments made so far. Some milestones of development - e.g. the German gas breeder memorandum, the Gas Breeder Reactor Association the results of the BR-2 radiation experiments and of GfK-KWU design and safety studies - are described. The problems connected with a large store of plutonium are also discussed. (UA/AK) [de

Identification and in vitro pharmacological characterization of a novel and selective α7 nicotinic acetylcholine receptor agonist, Br-IQ17B.

Science.gov (United States)

Tang, Jing-shu; Xie, Bing-xue; Bian, Xi-ling; Xue, Yu; Wei, Ning-ning; Zhou, Jing-heng; Hao, Yu-chen; Li, Gang; Zhang, Liang-ren; Wang, Ke-wei

2015-07-01

Alpha7-nicotinic acetylcholine receptor (α7 nAChR) is a ligand-gated Ca(2+)-permeable ion channel implicated in cognition and neuropsychiatric disorders. Activation of α7 nAChR improves learning, memory, and sensory gating in animal models. To identify novel α7 nAChR agonists, we synthesized a series of small molecules and characterized a representative compound, Br-IQ17B, N-[(3R)-1-azabicyclo[2,2,2]oct-3-yl]-5-bromoindolizine-2-carboxamide, which specifically activates α7 nAChR. Two-electrode voltage clamp (TEVC) recordings were primarily used for screening in Xenopus oocytes expressing human α7 nAChR. Assays, including radioisotope ligand binding, Western blots, whole-cell recordings of hippocampal culture neurons, and spontaneous IPSC recordings of brain slices, were also utilized to evaluate and confirm the specific activation of α7 nAChR by Br-IQ17B. Br-IQ17B potently activates α7 nAChR with an EC50 of 1.8±0.2 μmol/L. Br-IQ17B is selective over other subtypes such as α4β2 and α3β4, but it blocks 5-HT3A receptors. Br-IQ17B displaced binding of the α7 blocker [(3)H]-MLA to hippocampal crude membranes with a Ki of 14.9±3.2 nmol/L. In hippocampal neurons, Br-IQ17B evoked α7-like currents that were inhibited by MLA and enhanced in the presence of the α7 PAM PNU-120596. In brain slice recordings, Br-IQ17B enhanced GABAergic synaptic transmission in CA1 neurons. Mechanistically, Br-IQ17B increased ERK1/2 phosphorylation that was MLA-sensitive. We identified the novel, potent, and selective α7 agonist Br-IQ17B, which enhances synaptic transmission. Br-IQ17B may be a helpful tool to understand new aspects of α7 nAChR function, and it also has potential for being developed as therapy for schizophrenia and cognitive deficits.

Design of Rh/Ce0.2Zr0.8O2-Al2O3 nanocomposite for ethanol steam reforming

International Nuclear Information System (INIS)

De Rogatis, Loredana; Montini, Tiziano; Casula, Maria F.; Fornasiero, Paolo

2008-01-01

Rh(1 wt.%)/Ce 0.2 Zr 0.8 O 2 (10 wt.%)-Al 2 O 3 nanocomposite has been investigated as active and thermally stable catalyst for ethanol steam reforming. Rh nanoparticles were synthesised by surfactant assisted route, using N-hexadecyl-N-(2-hydroxyethyl)-N,N-dimethyl ammonium bromide (HEAC16Br). Metal particles with average diameter of 2.1 nm were obtained at 0.53 Rh/HEAC16Br molar ratio, while increasing the amount of surfactant lead to formation of larger particles. The preformed Rh nanoparticles have been effectively embedded into a porous layer of nanocomposite oxides. Low temperature H 2 chemisorption experiments and activity data confirm that most of the Rh atoms are accessible to the reaction mixture. The Ce 0.2 Zr 0.8 O 2 mixed oxide inhibits the dehydration of ethanol to ethylene and favours the water gas shift reaction. The alumina ensures good thermal stability and high surface area of the catalyst. No significant deactivation is observed after repeated run-up and run-down experiments

Three new chalcohalides, Ba4Ge2PbS8Br2, Ba4Ge2PbSe8Br2 and Ba4Ge2SnS8Br2: Syntheses, crystal structures, band gaps, and electronic structures

International Nuclear Information System (INIS)

Lin, Zuohong; Feng, Kai; Tu, Heng; Kang, Lei; Lin, Zheshuai; Yao, Jiyong; Wu, Yicheng

2014-01-01

Highlights: • Three new chalcohalides: Ba 4 Ge 2 PbS 8 Br 2 , Ba 4 Ge 2 PbSe 8 Br 2 and Ba 4 Ge 2 SnS 8 Br 2 have been synthesized. • The MQ 5 Br octahedra and GeQ 4 tetrahedra form a three-dimensional framework with Ba 2+ in the channels. • Band Gaps and electronic structures of the three compounds were studied. - Abstract: Single crystals of three new chalcohalides: Ba 4 Ge 2 PbS 8 Br 2 , Ba 4 Ge 2 PbSe 8 Br 2 and Ba 4 Ge 2 SnS 8 Br 2 have been synthesized for the first time. These isostructural compounds crystallize in the orthorhombic space group Pnma. In the structure, the tetra-valent Ge atom is tetrahedrally coordinated with four Q (Q = S, Se) atoms, while the bi-valent M atom (M = Pb, Sn) is coordinated with an obviously distorted octahedron of five Q (Q = S, Se) atoms and one Br atom, showing the stereochemical activity of the ns 2 lone pair electron. The MQ 5 Br (M = Sn, Pb; Q = S, Se) distorted octahedra and the GeQ 4 (Q = S, Se) tetrahedra are connected to each other to form a three-dimensional framework with channels occupied by Ba 2+ cations. Based on UV–vis–NIR spectroscopy measurements and the electronic structure calculations, Ba 4 Ge 2 PbS 8 Br 2 , Ba 4 Ge 2 PbSe 8 Br 2 and Ba 4 Ge 2 SnS 8 Br 2 have indirect band gaps of 2.054, 1.952, and 2.066 eV respectively, which are mainly determined by the orbitals from the Ge, M and Q atoms (M = Pb, Sn; Q = S, Se)

X-ray and NQR studies of bromoindate(III) complexes. [C2H5NH3]4InBr7, [C(NH2)3]3InBr6, and [H3NCH2C(CH3)2CH2NH3]InBr5

International Nuclear Information System (INIS)

Iwakiri, Takeharu; Ishihara, Hideta; Terao, Hiromitsu; Lork, Enno; Gesing, Thorsten M.

2017-01-01

The crystal structures of [C 2 H 5 NH 3 ] 4 InBr 7 (1), [C(NH 2 ) 3 ] 3 InBr 6 (2), and [H 3 NCH 2 C(CH 3 ) 2 CH 2 NH 3 ]InBr 5 (3) were determined at 100(2) K: monoclinic, P2 1 /n, a=1061.94(3), b=1186.40(4), c=2007.88(7) pm, β= 104.575(1) , Z=4 for 1; monoclinic, C2/c, a=3128.81(12), b=878.42(3), c=2816.50(10) pm, β=92.1320(10) , Z=16 for 2; orthorhombic, P2 1 2 1 2 1 , a=1250.33(5), b=1391.46(6), c=2503.22(9) pm, Z=4 for 3. The structure of 1 contains an isolated octahedral [InBr 6 ] 3- ion and a Br - ion. The structure of 2 contains three different isolated octahedral [InBr 6 ] 3- ions. The structure of 3 has a corner-shared double-octahedral [In 2 Br 11 ] 5- ion and an isolated tetrahedral [InBr 4 ] - ion. The 81 Br nuclear quadrupole resonance (NQR) lines of the terminal Br atoms of the compounds are widely spread in frequency, and some of them show unusual positive temperature dependence. These observations manifest the N-H..Br-In hydrogen bond networks developed between the cations and anions to stabilize the crystal structures. The 81 Br NQR and differential thermal analysis (DTA) measurements have revealed the occurrence of unique phase transitions in 1 and 3. When the bond angles were estimated from the electric field gradient (EFG) directions calculated by the molecular orbital (MO) methods, accurate values were obtained for [InBr 6 ] 3- of 1 and for [In 2 Br 11 ] 5- and [InBr 4 ] - of 3, except for several exceptions in those for the latter two ions. On the other hand, the calculations of 81 Br NQR frequencies have produced up to 1.4 times higher values than the observed ones.

Technical meeting on decommissioning of fast reactors after sodium draining. Working material

International Nuclear Information System (INIS)

2005-01-01

The objective of the technical meeting was to provide a forum for in-depth scientific and technical exchange on topics related to the decommissioning experience with fast reactors, in particular with regard to the decommissioning of components after sodium draining. Accordingly, the scope of the meeting covers the review and analyses of the experience gained from the decommissioning of both active sodium loops and sodium cooled fast reactors (e.g., KNK II, Superphenix, RAPSODIE, EBR-II, FERMI, BN-350, BR-10). It is expected that the outcome of the meeting will contribute to the Agency initiative to preserve fast reactor data and knowledge. The main focus of the technical meeting was given on the decommissioning of both active loop and reactor components (e.g., the primary vessel of a sodium-cooled reactor) that have been drained of sodium, but that still conserve some residual amounts of sodium (e.g., films covering the entire surface of the component, or particular sodium heels that cannot be drained)

"Brücke dreht sich um!". A Deconstructionist Reading of Kafka's "Die Brücke"

Directory of Open Access Journals (Sweden)

Eva Hoffmann

2014-12-01

Full Text Available Franz Kafka's (1883-1924 "Die Brücke" is one of the less well-known texts by one of the most prolific authors of literary modernity. However, this short prose text embodies prevalent questions of literary modernity and philosophy as it reflects the crisis of language in regard of identity, communication, and literary production. Placed in the context of fin-de-siècle's discourse of language crisis, this article provides a dialogue between Kafka's "Die Brücke" and Hannah Arendt's (1906-1975 philosophy of thinking and speaking in The Life of the Mind. Contrary to Arendt's understanding of the metaphor as "a carrying over" between the mental activities of the solitude thinker and a reconciliation with the pluralistic world shared with others, this article argues for a deconstructionist reading of "Die Brücke" as a tool to reevaluate Arendt's notion of a shared human experience ensured through language and illustrates the advantages of poetic texts within philosophical discourses.

Revised and extended analysis of the fifth spectrum of bromine: Br V

International Nuclear Information System (INIS)

Tauheed, A; Joshi, Y N

2009-01-01

The spectrum of four-times ionized bromine (Br V) has been investigated in the 350-1850 A wavelength region, which was recorded on a 3-m normal incidence spectrograph at the Antigonish laboratory using a triggered spark light source and on a 6.65-m grazing incidence spectrograph at the Zeeman laboratory in Amsterdam using a sliding spark source. We have studied the 4s 2 (4p+5p+6p+4f)+4p 3 +4s4p4d+4s4p5s configurations in the odd parity system and the 4s4p 2 , 4s 2 (4d+5d+5s+6s+7s) configurations in the even parity system. Relativistic Hartree-Fock (HFR) and least squares fitted (LSF) parametric calculations were carried out to interpret the observed spectrum. Fifty-eight Br V levels have now been established, out of which 48 are new levels. Two hundred and sixteen spectral lines have been classified in this spectrum, out of which 202 are newly classified lines. A revised value of the ionization potential has been determined to be 480 670±200 cm -1 (59.60±0.02 eV).

The n-butyl amine TPD measurement of Brönsted acidity for solid catalysts by simultaneous TG/DTG-DTA

Science.gov (United States)

Sasca, V.; Avram, Livia; Verdes, Orsina; Popa, A.

2010-06-01

The method for Brönsted acidity measurement based on TPD of alkyl amines desorption by gas-chromatography or thermogravimetry was adapted for simultaneous TG/DTG-DTA analysis. The acidity measurements were focused on the 12-tungstophosphoric acid (H 3PW 12O 40) and its salts, especially with Cesium since these posses the highest Brönsted acidity and they are among the most interesting catalysts. The n-butyl amine (NBA) desorption takes place in three steps for Cs xH 3- xPW 12O 40, x = 0-2, and four steps for the Cs 2.5H 0.5PW 12O 40. The steps of desorption correspond to the release of NBA molecules in stages, as NBA or butene molecules resulted from the Hofmann elimination reaction and NH 3 + H 2O formed by decomposition of ammonium salt. The quantities of desorption products, C 4H 8 and NH 3 + H 2O, corresponding to the stages with the maximum desorption rates at 400-420 °C, respectively 560-600 °C, are in the stoichiometric ratio with the Brönsted acidity.

Radiative forcing calculations for CH3Br

International Nuclear Information System (INIS)

Grossman, A.S.; Blass, W.E.; Wuebbles, D.J.

1995-06-01

Methyl Bromide, CH 3 Br, is the major organobromine species in the lower atmosphere and is a primary source of bromine in the stratosphere. It has a lifetime of 1.3 years. The IR methyl bromide spectra in the atmospheric window region, 7--13μ, was determined using a well tested Coriolis resonance and ell-doubling (and ell-resonance) computational system. A radiative forcing value of 0.00493 W/m 2 /ppbv was obtained for CH 3 Br and is approximately linear in the background abundance. This value is about 2 percent of the forcing of CFC-11 and about 278 times the forcing of C0 2 , on a per molecule basis. The radiative forcing calculation is used to estimate the global warming potential (GWP) of CH 3 Br. The results give GWPs for CH 3 Br of the order of 13 for an integration period of 20 years and 4 for an integration period of 100 years (assuming C0 2 = 1, following IPCC [1994]). While CH 3 Br has a GWP which is approximately 25 percent of the GWP of CH 4 , the current emission rates are too low to cause serious atmospheric greenhouse heating effects at this time

Brüssel Euroopa pealinnaks? / Ülar Mark

Index Scriptorium Estoniae

Mark, Ülar, 1968-

2009-01-01

Brüsseli Euroopa kvartali planeerimisvõistlusest, mille peakorraldaja oli Brüsseli pealinna piirkond koos Brüsseli linna ja Euroopa Komisjoniga. Eestist osales žüriis arhitekt Ülar Mark. Meeskonna Atelier Christian de Portzamparc võidutööst ja teiste teise vooru pääsenud nelja meeskonna (JDS / Julien De Smedt Architects, OMA / Office for Metropolitan Architecture, Xaveer De Geyter Architect, Fletcher Priest Architects) töödest

Palveluprosessi toimivaksi, Case: BR-Lelut

OpenAIRE

Korpela, Jenni

2014-01-01

Tämä opinnäytetyö on tehty toimeksiantona TOP-TOY A/S –konserniin kuluvalle lelumyymäläketju BR-Leluille Suomessa. Opinnäyte on toteutettu produktiluontoisena ja sen tuloksena on syntynyt Asiakaspalvelun ja myynnin käsikirja BR-Lelujen myymälähenkilökunnalle. Ajatus opinnäytetyölle ja eritoten käsikirjalle syntyi, kun kirjoittaja työskenteli kyseisen myymäläketjun myymälässä ja samanaikaisesti opiskeli erilaisia myyntitekniikoita ammattikorkeakoulussa. Kirjoittaja huomasi, että myyntihen...

Flg22-Triggered Immunity Negatively Regulates Key BR Biosynthetic Genes.

Science.gov (United States)

Jiménez-Góngora, Tamara; Kim, Seong-Ki; Lozano-Durán, Rosa; Zipfel, Cyril

2015-01-01

In plants, activation of growth and activation of immunity are opposing processes that define a trade-off. In the past few years, the growth-promoting hormones brassinosteroids (BR) have emerged as negative regulators of pathogen-associated molecular pattern (PAMP)-triggered immunity (PTI), promoting growth at the expense of defense. The crosstalk between BR and PTI signaling was described as negative and unidirectional, since activation of PTI does not affect several analyzed steps in the BR signaling pathway. In this work, we describe that activation of PTI by the bacterial PAMP flg22 results in the reduced expression of BR biosynthetic genes. This effect does not require BR perception or signaling, and occurs within 15 min of flg22 treatment. Since the described PTI-induced repression of gene expression may result in a reduction in BR biosynthesis, the crosstalk between PTI and BR could actually be negative and bidirectional, a possibility that should be taken into account when considering the interaction between these two pathways.

Room-temperature synthesis of pure perovskite-related Cs4PbBr6 nanocrystals and their ligand-mediated evolution into highly luminescent CsPbBr3 nanosheets

Science.gov (United States)

Yang, Liu; Li, Dongmei; Wang, Cong; Yao, Wei; Wang, Hao; Huang, Kaixiang

2017-07-01

Currently, all-inorganic cesium lead-halide perovskite nanocrystals have attracted enormous attentions owing to their excellent optical performances. While great efforts have been devoted to CsPbBr3 nanocrystals, the perovskite-related Cs4PbBr6 nanocrystals, which were newly reported, still remained poorly understood. Here, we reported a novel room-temperature reaction strategy to synthesize pure perovskite-related Cs4PbBr6 nanocrystals. Size of the products could be adjusted through altering the amount of ligands, simply. A mixture of two good solvents with different polarity was innovatively used as precursor solvent, being one key to the high-yield Cs4PbBr6 nanocrystals synthesis. Other two keys were Cs+ precursor concentration and surface ligands. Ingenious experiments were designed to reveal the underlying reaction mechanism. No excitonic emission was observed from the prepared Cs4PbBr6 nanocrystals in our work. We considered the green emission which was observed in other reports originated from the avoidless transformation of Cs4PbBr6 into CsPbBr3 nanocrystals. Indeed, the new-prepared Cs4PbBr6 nanocrystals could transform into CsPbBr3 nanosheets with surface ligands mediated. The new-transformed two-dimensional CsPbBr3 nanosheets could evolve into large-size nanosheets. The influences of surface ligand density on the fluorescent intensity and stability of transformed CsPbBr3 nanosheets were also explained. Notably, the photoluminescence quantum yield of the as-transformed CsPbBr3 nanosheets could reach as high as 61.6% in the form of thin film. The fast large-scale synthesis of Cs4PbBr6 nanocrystals and their ligand-mediated transformation into high-fluorescent CsPbBr3 nanosheets will be beneficial to the future optoelectronic applications. Our work provides new approaches to understand the structural evolution and light-emitting principle of perovskite nanocrystals. [Figure not available: see fulltext.

Kuluttaja-asiakkaiden mielikuva Concept.10-brändistä

OpenAIRE

Väisänen, Janna-Mari

2011-01-01

Tutkimuksen tavoitteena on selvittää, millainen käsitys Concept.10:n kuluttaja-asiakkailla on brändin eri osa-alueista ja millaisia mielleyhtymiä brändin mainonta, nimi, tunnus ja slogan herättävät. Näillä tekijöillä on vaikutusta kokonaismielikuvan syntymiseen brändistä. Tutkimusongelmana on, millainen mielikuva kuluttaja-asiakkailla on Concept.10-brändistä. Concept.10 toimii yhteisenä markkinointinimenä Mikkelin Puhelin Oyj:n omistamille yhtiöille ja niiden palveluille. Teoreettisessa v...

Non-enzymatic antioxidant accumulations in BR-deficient and BR-insensitive barley mutants under control and drought conditions.

Science.gov (United States)

Gruszka, Damian; Janeczko, Anna; Dziurka, Michal; Pociecha, Ewa; Fodor, Jozsef

2017-12-07

Drought is one of the most adverse stresses that affect plant growth and yield. Disturbances in metabolic activity resulting from drought cause overproduction of reactive oxygen species. It is postulated that brassinosteroids (BRs) regulate plant tolerance to the stress conditions, but the underlying mechanisms remain largely unknown. An involvement of endogenous BRs in regulation of the antioxidant homeostasis is not fully clarified either. Therefore, the aim of this study was to elucidate the role of endogenous BRs in regulation of non-enzymatic antioxidants in barley (Hordeum vulgare) under control and drought conditions. The plant material included the 'Bowman' cultivar and a group of semi-dwarf near-isogenic lines (NILs), representing mutants deficient in BR biosynthesis or signaling. In general, accumulations of 11 compounds representing various types of non-enzymatic antioxidants were analyzed under both conditions. The analyses of accumulations of reduced and oxidized forms of ascorbate indicated that the BR mutants contain significantly higher contents of dehydroascorbic acid under drought conditions when compared with the 'Bowman' cultivar. The analysis of glutathione accumulation indicated that under the control conditions the BR-insensitive NILs contained significantly lower concentrations of this antioxidant when compared with the rest of genotypes. Therefore, we postulate that BR sensitivity is required for normal accumulation of glutathione. A complete accumulation profile of various tocopherols indicated that functional BR biosynthesis and signaling are required for their normal accumulation under both conditions. Results of this study provided an insight into the role of endogenous BRs in regulation of the non-enzymatic antioxidant homeostasis. © 2017 Scandinavian Plant Physiology Society.

KBr-Li Br and KBr-LiBr doped with Ti mixed single crystal by Czochralski method and glow curve studies

International Nuclear Information System (INIS)

Faripour, H.; Faripour, N.

2003-01-01

Mixed-single Crystals: pure KBr-LiBr and KBr-LiBr with Ti dopant were grown by Czochralski method. Because of difference between lattice parameters of KBr and LiBr, the growth speed of crystals were relatively low, and they were annealed in a special temperature condition providing some cleavages. They were exposed by β radiation and the glow curve was analysed for each crystal. Analysing of glow curve, showed that Ti impurity has been the curves of main peak curve appearance temperature decreasing

Hurtigste versus mest brændstoføkonomiske ruter

DEFF Research Database (Denmark)

Andersen, Ove; Krogh, Benjamin Bjerre; Lahrmann, Harry

2013-01-01

Der er stort fokus på at forbedre brændstoføkonomien i transportbranchen generelt. I denne artikel anvendes brændstoftallene fra Controller Area Network Bus (CANBus) kombineret med GPS data til at skabe et digitalt vejkort, hvor det er muligt at sammenligne de hurtigste ruter med de mest brændsto...

IGORR 1: Proceedings of the 1. meeting of the International Group On Research Reactors

Energy Technology Data Exchange (ETDEWEB)

West, C D [comp.

1990-05-01

Descriptions of the ongoing projects presented at this Meeting were concerned with: New Research Reactor FRM-II at Munich; MITR-II reactor; The Advanced. Neutron Source (ANS) Project; The high Flux Reactor Petten, Status and Prospects; The High Flux Beam Reactor Instrumentation Upgrade; BER-II Upgrade; The BR2 Materials Testing Reactor Past, Ongoing and Under-Study Upgrades; The ORPHEE, Reactor Current Status and Proposed Enhancement of Experimental Variabilities; Construction of the Upgraded JRR-3; Status of the University of Missouri-Columbia Research Reactor Upgrade; the Reactor and Cold Neutron Facility at NIST; Upgrade of Materials Irradiation Facilities in HFIR; Backfitting of the FRG Reactors; University Research Reactors in the United States; and Organization of the ITER Project - Sharing of Informational Procurements. Topics of interest were: Thermal-hydraulic tests and correlations, Corrosion tests and analytical models , Multidimensional kinetic analysis for small cores, Fuel plates fabrication, Fuel plates stability, Fuel irradiation, Burnable poison irradiation, Structural materials irradiation, Neutron guides irradiation, Cold Source materials irradiation, Cold Source LN{sub 2} test, Source LH2-H{sub 2}O reaction (H or D), Instrumentation upgrading and digital control system, Man-machine interface.

IGORR 1: Proceedings of the 1. meeting of the International Group On Research Reactors

International Nuclear Information System (INIS)

West, C.D.

1990-05-01

Descriptions of the ongoing projects presented at this Meeting were concerned with: New Research Reactor FRM-II at Munich; MITR-II reactor; The Advanced. Neutron Source (ANS) Project; The high Flux Reactor Petten, Status and Prospects; The High Flux Beam Reactor Instrumentation Upgrade; BER-II Upgrade; The BR2 Materials Testing Reactor Past, Ongoing and Under-Study Upgrades; The ORPHEE, Reactor Current Status and Proposed Enhancement of Experimental Variabilities; Construction of the Upgraded JRR-3; Status of the University of Missouri-Columbia Research Reactor Upgrade; the Reactor and Cold Neutron Facility at NIST; Upgrade of Materials Irradiation Facilities in HFIR; Backfitting of the FRG Reactors; University Research Reactors in the United States; and Organization of the ITER Project - Sharing of Informational Procurements. Topics of interest were: Thermal-hydraulic tests and correlations, Corrosion tests and analytical models , Multidimensional kinetic analysis for small cores, Fuel plates fabrication, Fuel plates stability, Fuel irradiation, Burnable poison irradiation, Structural materials irradiation, Neutron guides irradiation, Cold Source materials irradiation, Cold Source LN 2 test, Source LH2-H 2 O reaction (H or D), Instrumentation upgrading and digital control system, Man-machine interface

CsPb2Br5 Single Crystals: Synthesis and Characterization

KAUST Repository

Dursun, Ibrahim

2017-08-02

CsPb2Br5 is a ternary halogen-plumbate material with close characteristics to well-reported halide perovskites. Due to its unconventional two-dimensional structure, CsPb2Br5 is being looked at broadly for potential applications in optoelectronics. CsPb2Br5 investigations are currently limited to nanostructures and powder forms of the material, which present unclear and conflicting optical properties. In this study, we present the synthesis and characterization of CsPb2Br5 bulk single crystals, which enabled us to finally clarify the material\\'s optical features. Our CsPb2Br5 crystal has a two-dimensional structure with Pb2Br5- layers spaced by Cs+ cations, and exhibits a ~3.1 eV indirect bandgap with no emission in the visible spectrum.

Longpath DOAS observations of surface BrO at Summit, Greenland

Directory of Open Access Journals (Sweden)

J. Stutz

2011-09-01

Full Text Available Reactive halogens, and in particular bromine oxide (BrO, have frequently been observed in regions with large halide reservoirs, for example during bromine catalyzed coastal polar ozone depletion events. Much less is known about the presence and impact of reactive halogens in areas without obvious halide reservoirs, such as the polar ice sheets or continental snow. <br>> We report the first LP-DOAS measurements of BrO at Summit research station in the center of the Greenland ice sheet at an altitude of 3200 m. BrO mixing ratios in May 2007 and June 2008 were typically between 1–3 pmol mol⁻¹, with maxima of up to 5 pmol mol⁻¹. These measurements unequivocally show that halogen chemistry is occurring in the remote Arctic, far from known bromine reservoirs, such as the ocean. During periods when FLEXPART retroplumes show that airmasses resided on the Greenland ice sheet for 3 or more days, BrO exhibits a clear diurnal variation, with peak mixing ratios of up to 3 pmol mol⁻¹ in the morning and at night. The diurnal cycle of BrO can be explained by a changing boundary layer height combined with photochemical formation of reactive bromine driven by solar radiation at the snow surface. The shallow stable boundary layer in the morning and night leads to an accumulation of BrO at the surface, leading to elevated BrO despite the expected smaller release from the snowpack during these times of low solar radiation. During the day when photolytic formation of reactive bromine is expected to be highest, efficient mixing into a deeper neutral boundary layer leads to lower BrO mixing ratios than during mornings and nights. <br>> The extended period of contact with the Greenland snowpack combined with the diurnal profile of BrO, modulated by boundary layer height, suggests that photochemistry in the snow is a significant source of BrO measured at Summit during the 2008 experiment. In addition, a rapid transport event

Elamusturundus: riigi brändimine ja Eesti bränd / Siiri Same

Index Scriptorium Estoniae

Same, Siiri

2015-01-01

Artikli autor oma 2015. a. Tallinna Tehnikaülikoolis kaitstud doktoritööst "Conceptualization of experience marketing and country branding from a marketing management perspective" ("Elamusturunduse ja riigi brändimise kontseptualiseerimine turunduse juhtimise vaatenurgast")

Evaluation of the levels of Br, Cl, K, Mg, Mn and V in Perna perna Mussels (Linnaeus, 1758: Mollusca, Bivalvia) collected in coast of Sao Paulo, Brazil

International Nuclear Information System (INIS)

Seo, Daniele; Vasconcellos, Marina B.A.; Saiki, Mitiki; Catharino, Marilia G.M.; Moreira, Edson G.; Sousa, Eduinetty C.P.M. de

2013-01-01

In this study the content of Br, Cl, K, Mg, Mn and V was evaluated in samples of Perna perna mussels collected in coastal regions of Sao Paulo (Ponta de Itaipu and Palmas Island, in Santos) subjected to anthropogenic contamination, to compare these values with those of mussels from reference site of Cocanha Beach (in Caraguatatuba). The mussels were collected seasonally from September 2008 to July 2009. They were cleaned, ground, homogenized, lyophilized and then analyzed by Instrumental Neutron Activation Analysis (INAA). The INAA procedure consisted in the irradiation of the samples and synthetic elemental standards for 8 and 10 s, under a thermal neutron flux of 6.6 x 10 12 n cm -2 s -1 in the IEA-R1 nuclear research reactor. For quality control of analytical results, certified reference materials NIST 1566b Oyster Tissue and NIST 2876 Mussel Tissue were analyzed and their results indicated good accuracy. The ranges of concentrations (dry basis) of the elements obtained in mussels collected for the four seasons of the year were: 173.80 to 358.99 mg kg -1 for Br; 45658 ± 1811 to 109166 ± 824 mg kg -1 for Cl; 7043 ± 856 to 12506 ± 675 mg kg -1 for K; 2774 ± 211 to 5691 ± 717 mg kg -1 for Mg; 7.01 ± 0.30 to 29.74 ± 3.32 mg kg -1 for Mn and 0.77 ± 0.02 to 3.43 ± 0.28 mg kg -1 for V. The seasonal and spatial variations of these element concentrations were in this study. (author)

Evaluation of the levels of Br, Cl, K, Mg, Mn and V in Perna perna Mussels (Linnaeus, 1758: Mollusca, Bivalvia) collected in coast of Sao Paulo, Brazil

Energy Technology Data Exchange (ETDEWEB)

Seo, Daniele; Vasconcellos, Marina B.A.; Saiki, Mitiki; Catharino, Marilia G.M.; Moreira, Edson G., E-mail: danyseo@uol.com.br, E-mail: mbvascon@ipen.br, E-mail: mitiko@ipen.br, E-mail: mgcatharino@uol.com.br, E-mail: emoreira@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Sousa, Eduinetty C.P.M. de, E-mail: edvinett@usp.br [Universidade de Sao Paulo (IO/USP), Sao Paulo, SP (Brazil). Instituto Oceanografico. Laboratorio de Ecotoxicologia Marinha e Microfitobentos

2013-07-01

In this study the content of Br, Cl, K, Mg, Mn and V was evaluated in samples of Perna perna mussels collected in coastal regions of Sao Paulo (Ponta de Itaipu and Palmas Island, in Santos) subjected to anthropogenic contamination, to compare these values with those of mussels from reference site of Cocanha Beach (in Caraguatatuba). The mussels were collected seasonally from September 2008 to July 2009. They were cleaned, ground, homogenized, lyophilized and then analyzed by Instrumental Neutron Activation Analysis (INAA). The INAA procedure consisted in the irradiation of the samples and synthetic elemental standards for 8 and 10 s, under a thermal neutron flux of 6.6 x 10{sup 12} n cm{sup -2} s{sup -1} in the IEA-R1 nuclear research reactor. For quality control of analytical results, certified reference materials NIST 1566b Oyster Tissue and NIST 2876 Mussel Tissue were analyzed and their results indicated good accuracy. The ranges of concentrations (dry basis) of the elements obtained in mussels collected for the four seasons of the year were: 173.80 to 358.99 mg kg{sup -1} for Br; 45658 ± 1811 to 109166 ± 824 mg kg{sup -1} for Cl; 7043 ± 856 to 12506 ± 675 mg kg{sup -1} for K; 2774 ± 211 to 5691 ± 717 mg kg{sup -1} for Mg; 7.01 ± 0.30 to 29.74 ± 3.32 mg kg{sup -1} for Mn and 0.77 ± 0.02 to 3.43 ± 0.28 mg kg{sup -1} for V. The seasonal and spatial variations of these element concentrations were in this study. (author)

Dynamic study of an anaerobic reactor in pilot plant scale using radioactive tracer

International Nuclear Information System (INIS)

Pinto, A.M.F.; Moreira, R.M.; Chernicharo, C.A.L.

1995-01-01

The use of flow traces is a common practice in hydrodynamic studies. However chemical tracers have some shortcomings, such as the need of sampling, analysis and possible interferences with the delicate biological processes taking place within the reactor. Thus a radiotracer, Br 82 has been chosen for this purpose. The advantages of this radioisotope are its energetic gamma emission which can be easily detected outside the reactor walls, its solubility and lack of adsorption, besides having a convenient half-life and being easily produced is small nuclear reactors. The tracer responses to instantaneous injections at the reactor entrance were used to determine the resistance time and the mixing patterns of the reactors. The normalized residence time distributions were fitted to mathematical models by a least-squares subroutine. The axial dispersion model and the tanks-in-series model have been used, thus allowing the determination of the dispersion coefficient and the Peclet Number. (author). 5 refs, 4 figs, 1 tab

Participation of IRD/CNEN-Br in International Intercomparison of Criticality Accident Dosimetry Systems at Silene reactor, France

International Nuclear Information System (INIS)

Mauricio, Claudia Lucia P.; Fonseca, Evaldo S. da

1996-01-01

IRD has participated in an International Intercomparison of Criticality Accident Dosimetry Systems at the SILENE reactor, France on June 1993. The dosemeters were irradiated on phantoms and free in air, in bare and lead shield reactor pulses, simulating different irradiation fields that can be found in criticality accidents. Comparing with the reference measurements, the calculated mean neutron kerma found by IRD was only 2% greater for lead shield and 14% greater for bare reactor. For gamma absorbed dose, the differences were, respectively + 22% and -9% for the dosemeters free in air and -19% and -9% for dosemeters on phantoms. IRD results are closer to the real values than the mean values measured by the participants. IRD results show a good performance if its simple criticality accident system. (author)

Improved Growth Methods for LaBr3 Scintillation Radiation Detectors

International Nuclear Information System (INIS)

McGregor, Douglas S.

2011-01-01

The objective is to develop advanced materials for deployment as high-resolution gamma ray detectors. Both LaBr3 and CeBr3 are advanced scintillation materials, and will be studied in this research. Prototype devices, in collaboration Sandia National Laboratories, will be demonstrated along with recommendations for mass production and deployment. It is anticipated that improved methods of crystal growth will yield larger single crystals of LaBr3 for deployable room-temperature operated gamma radiation spectrometers. The growth methods will be characterized. The LaBr3 and CeBr3 scintillation crystals will be characterized for light yield, spectral resolution, and for hardness.

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

Energy Technology Data Exchange (ETDEWEB)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 Surveillance and Vessel Plates to the Surrogate Plates Representative of the Yankee Rowe PWR Vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1998-07-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ( 260 degrees Celsius) and their plates were austenitized a higher-than-usual temperature (970 degrees Celsius) - a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behaviour characterized by a 41 J Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rate plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares free complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63 % (A533-B) and YA9, 0.19 (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program: this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and

Comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe PWR vessel

International Nuclear Information System (INIS)

Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

1999-01-01

The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature (∼260 C) and their plates were austenitized at higher-than-usual temperature (∼970 C) -- a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behavior characterized by a 41J. Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program; this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the BR3 vessel

Seismic stability analyses of various reactor buildings on quaternary deposit

International Nuclear Information System (INIS)

Takeuchi, Y.; Tsutagawa, M.; Asakura, S.; Katoh, T.; Tomura, H.; Uchiyama, S.; Koyama, M.; Oguro, E.; Akino, K.; Iizuka, S.; Hayashi, M.

1993-01-01

Many nuclear power plants have been built on Quaternary deposits in Europe and U.S.A., however, Japanese basic policy is to construct the reactor building and other auxiliary buildings on a bed rock which are important to safety, because large earthquakes are postulated to occur. Being limited bed rock sites in Japan, it has become necessary to increase possible place for nuclear power plant in order to cope with the middle and long term siting problems. For the purpose of establishing the draft of guideline on seismic design of reactor building on the Quaternary sand and gravel deposit in Japan, foundation soil stability and seismic resistance of the reactor building and plant equipment have been investigated and studied from 1983 to 1998. The studies have shown the following: 1) The response rotation angles of both common light weight basement (CL) and step basement (ES) plants during the earthquake reduce to 1/2 of the BR plant value, and the bearing pressure between the basement and the soil of improved plant are reduced as well; (2) every structure built on quaternary sand and gravel deposit, having 400m/s shear velocity, maintains enough seismic resistance, because the shear stress caused in the wall is small. The maximum shear strain of soil below the basemat of BR-BWR, which suffers the largest bearing pressure, is 1.1x10 -9 , but it can be said that the soil has enough stability according to the past soil tests for the Quaternary sand and gravel deposit that had been done by authors

Efficiency factor of a chemical nuclear reactor with gamma sources

International Nuclear Information System (INIS)

Anguis T, C.

1975-01-01

A chemonuclear reactor is simulated in order to calculate the efficiency factor of molecular species in chemical reactions induced by gamma radiation, with the purpose to obtain information for its design and consider the electromagnetic energy as a possible solution to the present problem of energy. The research is based on a mathematical model of succesive Compton processes applied to spherical and cylindrical geometry and corroborated through the absorbed dose and the experimental date of the increase factor, for the radioisotopic sources Co-60 and Cs-137 relating the quantity of energy deposited into various cylinders with the G value, the relation radius/height of the reactor is optimized according to the molecular production. This is illustrated with the radiolysis of a solution of CH 3 OH/H 2 O which forms H 2 and with the obtainment of C 2 H 5 Br that represents and industrial process induced radioactively. The results show a greater energy deposition with Cs-137 but a larger production of H 2 /hr with Co-60, and besides we can find high production values of C 2 H 5 Br. The cylinder with more advantages is that whose relation R/H is of 0.5. It can be concluded that the final selection of the reactor should be made after a more intense study of the used isotope and the source activity. The efficiency factor of H 2 can be increased selecting the appropriate type and concentration of solute of the irradiated aqueous solutions

An analysis of postulated accident for 49-2 Swimming Pool Reactor

International Nuclear Information System (INIS)

Wang Yongqing; Cu Shaochu; Wang Liugui; Zhang Zengqing

1990-01-01

The thermal hydrodynamic code RETRAN-02 is used for safety analysis of Swimming Pool Reactor. Accident of partial-loss of flow, loss of offsite electric power and unexpected reactivity insertion are analysed and discussed. These results will be helpful for operation safety of the reactor

La Alpaca -vaatemerkin brändäys

OpenAIRE

Lehtinen, Laura

2013-01-01

Tämä opinnäytetyö käsittelee brändin vahvistamista ja brändiohjeiston luomista vaa-tealan yritykselle La Alpacalle. La Alpaca on suomalainen vaatemerkki, joka suunnit-telee, tuottaa ja myy alpakanvillasta valmistettuja tuotteita. Materiaalin ainutlaatuisuus ja hienous ovat olleet osa yrityksen identiteettiä alusta asti. Brändin lisäksi työssä on tutkittu kaupankäynnin rakenteellista muuttumista perinteisestä myymälätoiminnasta verkkomyyntiin. Työn tavoitteena on ollut luoda materiaalin tun...

Materials specific work at Forschungszentrum Karlsruhe and in cooperation with the industrial partners ALKEM and Interatom for the development of nuclear oxide fuels for fission reactors

International Nuclear Information System (INIS)

Kleykamp, H.; Muehling, G.

2005-09-01

The fabrication of uranium-plutonium oxide fuel started in Forschungszentrum Karlsruhe and at ALKEM company to begin for the criticality experiments in the SNEAK reactor and subsequently for stationary fuel pin irradiations in the FR2, BR2, DFR, Rapsodie, Phenix and KNK II reactors. The production methods comprised first the mechanical blending of UO2 and PuO2 followed by direct pressing and sintering of the pellets, later the advanced methods such as optimized comilling and ammonium uranyl plutonyl coprecititation. The fabrication of pellets was described in the main, further the alternative fuel pin manufacturing processes by vibrational compaction and hot-impact densification were discussed. The first capsule and pin irradiations in the FR2 and BR2 reactors contributed to the assessment of the maximum operation parameters within the fuel pin development such as linear heat rating, cladding temperature and burnup. Subsequently, small-bundle and largebundle irradiations were made in fast reactors in cooperation with Interatom company in order to verify the specifications for the commercial fast reactor SNR 300. Milestones were the maximum burnup of 175 GWd/t metal, corresponding 18.6 % of the heavy atoms, obtained in one of the KNK II fuel pin assemblies, and the displacement rates in the cladding materials of 140 dpa NRT attained in the Phenix reactor. Higher implications gained later the stationary irradiations of defected mixed-oxide pins, the mild fuel pin transient operations, the local blockage experiments and the severe hypothetic accidents in the respective Siloe, HFR, BR2 and CABRI reactors. These experiments were made solely in international partnership. Further activities were the chemical analyses of solid residues and coprecipitations of irradiated mixed-oxide fuels in the head-end of the reprocessing. All these actions were coordinated in the then fast breeder project. Furthermore, irradiated fuels and fuel pins of other reactor types were

Photoelectron Emission Studies in CsBr at 257 nm

International Nuclear Information System (INIS)

Maldonado, Juan R.; Liu, Zhi; Sun, Yun; Pianetta, Piero A.; Pease, Fabian W.

2006-01-01

CsBr/Cr photocathodes were found [1,2] to meet the requirements of a multi-electron beam lithography system operating with a light energy of 4.8 eV (257nm). The fact that photoemission was observed with a light energy below the reported 7.3 eV band gap for CsBr was not understood. This paper presents experimental results on the presence of intra-band gap absorption sites (IBAS) in CsBr thin film photo electron emitters, and presents a model based on IBAS to explain the observed photoelectron emission behavior at energies below band gap. A fluorescence band centered at 330 nm with a FWHM of about 0.34 eV was observed in CsBr/Cr samples under 257 nm laser illumination which can be attributed to IBAS and agrees well with previously obtained synchrotron photoelectron spectra[1] from the valence band of CsBr films

Elastic properties of Cs2HgBr4 and Cs2CdBr4 crystals

International Nuclear Information System (INIS)

Kityk, A.V.; Zadorozhna, A.V.; Shchur, Y.I.; Martynyuk-Lototska, Y.I.; Burak, Y.; Vlokh, O.G.

1998-01-01

Using ultrasonic velocity measurements, all components of the elastic constant matrix C ij , elastic compliances matrix S ij , and linear compressibility constants matrix K ij of orthorhombic Cs 2 HgBr 4 and Cs 2 CdBr 4 crystals have been determined over a wide temperature range, including the region of the phase transition from the normal to the incommensurate phase. Results obtained are considered within the framework of the phenomenological theory. Preliminary analysis of the acoustical properties at room temperature clearly indicates that both crystals are relatively important materials for acousto-optical applications. Copyright (1998) CSIRO Australia

Br...Br and van der Waals interactions along a homologous series: crystal packing of 1,2-dibromo-4,5-dialkoxybenzenes.

Science.gov (United States)

Suarez, Sebastián A; Muller, Federico; Gutiérrez Suburu, Matías E; Fonrouge, Ana; Baggio, Ricardo F; Cukiernik, Fabio D

2016-10-01

The crystalline structures of four homologues of the 1,2-dibromo-4,5-dialkoxybenzene series [Br 2 C 6 H 2 (OC n H 2n + 1 ) 2 for n = 2, 12, 14 and 18] have been solved by means of single-crystal crystallography. Comparison along the series, including the previously reported n = 10 and n = 16 derivatives, shows a clear metric trend (b and c essentially fixed along the series and a growing linearly with n), in spite of some subtle differences in space groups and/or packing modes. A uniform packing pattern for the aliphatic chains has been found for the n = 12 to 18 homologues, which slightly differs from that of the n = 10 derivative. The crystalline structures of all the higher homologues (n = 10-18) seem to arise from van der Waals interchain interactions and, to a lesser extent, type II Br...Br interactions. The dominant role of interchain interactions provides direct structural support for the usual interpretation of melting point trends like that found along this series. Atoms in Molecules (AIM) analysis allows a comparison of the relative magnitude of the interchain and Br...Br interactions, an analysis validated by the measured melting enthalpies.

Performance evaluation of LaBr3: Ce scintillator

International Nuclear Information System (INIS)

Xie Ming; Lin Li; Liu Shihao; Xiao Peng; Xie Qingguo

2012-01-01

The cerium doped lanthanum bromide crystal (LaBr 3 : Ce) is a new kind of scintillator with many advantages such as good energy resolution, high light output, short decay time, good proportionality response. These properties make the LaBr 3 : Ce attractive substantial interest to use in the radiation detection. The energy resolution were investigated with Φ25 × 25 mm LaBr 3 : Ce coupled to a Hamamatsu R8900 photomultiplier tube. Energy resolution of 3.6% (FWHM) have been achieved for 511 keV photons ( 18 F source) at room temperature. Decay time constant of 20 ns have been acquired with a Hamamatsu fast-time-response R9800 photomultiplier tube. The results approve the excellent characterizations of LaBr 3 : Ce and imply its enormous potentiality in the radiation detectors of gamma-ray spectroscopy and PET. (authors)

Synthesis and crystal structure determination of Br2SeIBr ...

Indian Academy of Sciences (India)

Unknown

termined by single crystal X-ray diffraction method. This compound was ... company and SeBr4 was prepared from the reaction of Se powder (0⋅1 g) with Br2 ... angles of Br2SeIBr and table 4 shows anisotropic displace- ment parameters.

ARIES tokamak reactor study

International Nuclear Information System (INIS)

Steiner, D.; Embrechts, M.

1990-07-01

This is a status report on technical progress relative to the tasks identified for the fifth year of Grant No. FG02-85-ER52118. The ARIES tokamak reactor study is a multi-institutional effort to develop several visions of the tokamak as an attractive fusion reactor with enhanced economic, safety, and environmental features. The ARIES study is being coordinated by UCLA and involves a number of institutions, including RPI. The RPI group has been pursuing the following areas of research in the context of the ARIES-I design effort: MHD equilibrium and stability analyses; plasma-edge modeling and blanket materials issues. Progress in these areas is summarized herein

Water-resistant, monodispersed and stably luminescent CsPbBr3/CsPb2Br5 core-shell-like structure lead halide perovskite nanocrystals

Science.gov (United States)

Qiao, Bo; Song, Pengjie; Cao, Jingyue; Zhao, Suling; Shen, Zhaohui; Gao, Di; Liang, Zhiqin; Xu, Zheng; Song, Dandan; Xu, Xurong

2017-11-01

Lead halide perovskite materials are thriving in optoelectronic applications due to their excellent properties, while their instability due to the fact that they are easily hydrolyzed is still a bottleneck for their potential application. In this work, water-resistant, monodispersed and stably luminescent cesium lead bromine perovskite nanocrystals coated with CsPb2Br5 were obtained using a modified non-stoichiometric solution-phase method. CsPb2Br5 2D layers were coated on the surface of CsPbBr3 nanocrystals and formed a core-shell-like structure in the synthetic processes. The stability of the luminescence of the CsPbBr3 nanocrystals in water and ethanol atmosphere was greatly enhanced by the photoluminescence-inactive CsPb2Br5 coating with a wide bandgap. The water-stable enhanced nanocrystals are suitable for long-term stable optoelectronic applications in the atmosphere.

Shape and phase evolution from CsPbBr3 perovskite nanocubes to tetragonal CsPb2Br5 nanosheets with an indirect bandgap.

Science.gov (United States)

Li, Guopeng; Wang, Hui; Zhu, Zhifeng; Chang, Yajing; Zhang, Ting; Song, Zihang; Jiang, Yang

2016-09-13

Tetragonal CsPb 2 Br 5 nanosheets were obtained by an oriented attachment of orthorhombic CsPbBr 3 nanocubes, involving a lateral shape evolution from octagonal to square. Meanwhile, the experimental results, together with DFT simulation results, indicated that the tetragonal CsPb 2 Br 5 is an indirect bandgap semiconductor that is PL-inactive with a bandgap of 2.979 eV.

Breeding capability and void reactivity analysis of heavy-water-cooled thorium reactor

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2008-01-01

The fuel breeding and void reactivity coefficient of thorium reactors have been investigated using heavy water as coolant for several parametric surveys on moderator-to-fuel ratio (MFR) and burnup. The equilibrium fuel cycle burnup calculation has been performed, which is coupled with the cell calculation for this evaluation. The η of 233 U shows its superiority over other fissile nuclides in the surveyed MFR ranges and always stays higher than 2.1, which indicates that the reactor has a breeding condition for a wide range of MFR. A breeding condition with a burnup comparable to that of a standard PWR or higher can be achieved by adopting a larger pin gap (1-6 mm), and a pin gap of about 2 mm can be used to achieve a breeding ratio (BR) of 1.1. A feasible design region of the reactors, which fulfills the breeding condition and negative void reactivity coefficient, has been found. A heavy-water-cooled PWR-type Th- 233 U fuel reactor can be designed as a breeder reactor with negative void coefficient. (author)

Reversible light-mediated compositional and structural transitions between CsPbBr3 and CsPb2Br5 nanosheets.

Science.gov (United States)

Shen, Wei; Ruan, Longfei; Shen, Zhitao; Deng, Zhengtao

2018-03-13

This communication describes a new method to achieve reversible light-induced chemical composition and phase structural transitions from polyvinylpyrrolidone-capped orthorhombic CsPbBr 3 to tetragonal CsPb 2 Br 5 nanosheets or vice versa. This work will deepen our understanding of the controlled synthesis, post-processing, and decomposition pathway of cesium lead halide perovskite nanocrystals.

New fuels for proliferation-safe research reactors. SCK-CEN a kingpin in international research

International Nuclear Information System (INIS)

Van den Berghe, S.

2011-01-01

A number of research reactors in the world, including BR2, are still working on highly enriched proliferation sensitive nuclear fuel. Extremely high-density fuel is required to make possible the switch to low-enriched fuel without loss of effectiveness. In the past few years, SCK-CEN has developed into the global test station for new, low-enriched fuels.

Paysans du Brésil

Directory of Open Access Journals (Sweden)

Dominique Temple

2007-01-01

Full Text Available Eric Sabourin, « Paysans du Brésil : Entre échange marchand et réciprocité » Paris, Editions Quae, 241p, 30 euros, (préface de Maxime Haubert, 2007Dans la présentation du livre, Maxime Haubert dit :«Cet ouvrage propose une analyse socio-anthropologique et agronomique des sociétés rurales et paysannes du Brésil et des transformations qu'elles ont connues ces dernières décennies, en particulier face aux interventions de l'Etat et à l'expansion du marché capitaliste (.... «Le livre pose d'abor...

Preliminary design report: Babcock and Wilcox BR-100 100-ton rail/barge spent fuel shipping cask

International Nuclear Information System (INIS)

1990-02-01

The purpose of this document is to provide information on burnup credit as applied to the preliminary design of the BR-100 shipping cask. There is a brief description of the preliminary basket design and the features used to maintain a critically safe system. Following the basket description is a discussion of various criticality analyses used to evaluate burnup credit. The results from these analyses are then reviewed in the perspective of fuel burnups expected to be shipped to either the final repository or a Monitored Retrievable Storage (MRS) facility. The hurdles to employing burnup credit in the certification of any cask are then outlines and reviewed. the last section gives conclusions reached as to burnup credit for the BR-100 cask, based on our analyses and experience. All information in this study refers to the cask configured to transport PWR fuel. Boiling Water Reactor (BWR) fuel satisfies the criticality requirements so that burnup credit is not needed. All calculations generated in the preparation of this report were based upon the preliminary design which will be optimized during the final design. 8 refs., 19 figs., 16 tabs

Design and implementation of tutorials for PLC B&R Automation

OpenAIRE

Sýkora, Daniel

2014-01-01

Tato bakalářská práce se zabývá návrhem a realizací úloh pro PLC B&R a podrobným návodem práce v Automation Studio. Obsahuje také informace o firmě B&R Automation Ges. m. b. H. a jejích produktech. Návrh úloh probíhal ve vývojovém prostředí B&R Automation Studio. Praktická úloha na regulaci teploty byla řešena a odzkoušena na B&R PLC X20. This bachelor’s thesis deals with the design and the implementation tutorials for PLC B&R as well as the detailed instructions of work in the Automation ...

Final report. U.S. Department of Energy University Reactor Sharing Program

Energy Technology Data Exchange (ETDEWEB)

Bernard, John A

2003-01-21

Activities supported at the MIT Nuclear Reactor Laboratory under the U.S. DOE University Reactor Sharing Program are reported for Grant DE FG02-95NE38121 (September 16, 1995 through May 31, 2002). These activities fell under four subcategories: support for research at thesis and post-doctoral levels, support for college-level laboratory exercises, support for reactor tours/lectures on nuclear energy, and support for science fair participants.

Production of 77 Br for medical application

International Nuclear Information System (INIS)

Bastos, M.A.V.

1982-01-01

Bromine-77 is produced with the variable energy cyclotron (CV-28) at the Instituto de Engenharia Nuclear, via the 75 As. (α, 2 n) 77 Br reaction, by bombarding arsenic trioxide with 28 MeV alpha-particles. The thick target yield is 0.3 mCi/μAh. The target is dissolved in concentrated N H 4 OH and 77 Br, separated from arsenic, by an anionic exchange resin, is obtained carrier-free with a separation yield greater than 90%. All the process is remotely controlled using electric and pneumatic systems, manipulators and tongs. The quality control is made by atomic absorption and gamma-ray spectroscopy. The present production rate of Br-77 is 2.3 mCi per irradiation. (author)

Characterization of the LiSi/CsBr-LiBr-KBr/FeS(2) System for Potential Use as a Geothermal Borehole Power Source

International Nuclear Information System (INIS)

GUIDOTTI, RONALD A.; REINHARDT, FREDERICK W.

1999-01-01

We are continuing to study the suitability of modified thermal-battery technology as a potential power source for geothermal borehole applications. Previous work focused on the LiSi/FeS(sub 2) couple over a temperature range of 350 C to 400 C with the LiBr-KBr-LiF eutectic, which melts at 324.5 C. In this work, the discharge processes that take place in LiSi/CsBr-LiBr-KBr eutectic/FeS(sub 2) thermal cells were studied at temperatures between 250 C and 400 C using pelletized cells with immobilized electrolyte. The CsBr-LiBr-KBr eutectic was selected because of its lower melting point (228.5 C). Incorporation of a quasi-reference electrode allowed the determination of the relative contribution of each electrode to the overall cell polarization. The results of single-cell tests and limited battery tests are presented, along with preliminary data for battery stacks tested in a simulated geothermal borehole environment

Is the 'Bromine Explosion' generated from the reaction BrO HO2 alone?

Science.gov (United States)

Behnke, Wolfgang; Zetzsch, Cornelius

2010-05-01

We observed bromine explosions (a fast production of atomic Br and Cl under tropospheric conditions) in various smog chamber experiments in Teflon bags at room temperature at a relative humidity of about 80% in the presence of NaCl/NaBr-aerosol, simulated sunlight and ozone (200 - 400 ppb). Time profiles of ozone and hydrocarbons (HCs: n-butane, 2,2-dimethylbutane, tetramethylbutane and toluene, initially about 2 ppb each) were monitored to determine concentrations and source strengths of OH radicals, atomic Cl and Br and the corresponding time profiles of BrCl and Br2 as their photolytic precursors. The number and size of aerosols are measured as well as their chemical composition (Br-, Cl- and oxalic acid). Full records of raw data from the smog chamber runs are available at www.eurochamp.org for potential users. Chemical box model calculations deliver concentrations of various intermediates, such as aldehydes, HO2 and RO2 radicals and the inorganic halogen compounds ClO, BrO, HOCl and HOBr, where HOBr from O3 + Br- => BrO- + O2 in the aqueous/adsorbed phase induces the following gas-phase/ heterogeneous chain reaction Br + O3 => BrO + O2(1) BrO + HO2 => HOBr + O2(2a) HOBr + (Aerosol) => HOBrad(3) Surface-adsorbed HOBr reacts with Br- or Cl- to produce Br2 or BrCl, both of which are released and photolysed. Formation of Br2 should prevail up to Cl-/Br- -ratios of about 104 (Fickert, S., J.W. Adams, J.N. Crowley, J. Geophys. Res., D104, 23719-23727, 1999). A maximum of this ratio is reached about 30 minutes after the beginning and decreases during the next hours - probably by reaction of Br2 with oxalate and absorption of HBr, formed from the reaction of Br with aldehydes. Parallel to chain reaction (1)-(3) a chain reaction replacing Br by Cl seems possible but can not be realized, since the main sink of atomic Cl is its reaction with hydrocarbons - leading to chain termination - in contrast to atomic Br (ratio of rates: kCl[O3]/kCl[HC] ~ 0.1; kBr[O3]/kBr

Facile synthesis of CsPbBr3/PbSe composite clusters.

Science.gov (United States)

Nguyen, Thang Phan; Ozturk, Abdullah; Park, Jongee; Sohn, Woonbae; Lee, Tae Hyung; Jang, Ho Won; Kim, Soo Young

2018-01-01

In this work, CsPbBr 3 and PbSe nanocomposites were synthesized to protect perovskite material from self-enlargement during reaction. UV absorption and photoluminescence (PL) spectra indicate that the addition of Se into CsPbBr 3 quantum dots modified the electronic structure of CsPbBr 3 , increasing the band gap from 2.38 to 2.48 eV as the Cs:Se ratio increased to 1:3. Thus, the emission color of CsPbBr 3 perovskite quantum dots was modified from green to blue by increasing the Se ratio in composites. According to X-ray diffraction patterns, the structure of CsPbBr 3 quantum dots changed from cubic to orthorhombic due to the introduction of PbSe at the surface. Transmission electron microscopy and X-ray photoemission spectroscopy confirmed that the atomic distribution in CsPbBr 3 /PbSe composite clusters is uniform and the composite materials were well formed. The PL intensity of a CsPbBr 3 /PbSe sample with a 1:1 Cs:Se ratio maintained 50% of its initial intensity after keeping the sample for 81 h in air, while the PL intensity of CsPbBr 3 reduced to 20% of its initial intensity. Therefore, it is considered that low amounts of Se could improve the stability of CsPbBr 3 quantum dots.

A comparative study of LaBr3(Ce(3+)) and CeBr3 based gamma-ray spectrometers for planetary remote sensing applications.

Science.gov (United States)

Kozyrev, A; Mitrofanov, I; Owens, A; Quarati, F; Benkhoff, J; Bakhtin, B; Fedosov, F; Golovin, D; Litvak, M; Malakhov, A; Mokrousov, M; Nuzhdin, I; Sanin, A; Tretyakov, V; Vostrukhin, A; Timoshenko, G; Shvetsov, V; Granja, C; Slavicek, T; Pospisil, S

2016-08-01

The recent availability of large volume cerium bromide crystals raises the possibility of substantially improving gamma-ray spectrometer limiting flux sensitivities over current systems based on the lanthanum tri-halides, e.g., lanthanum bromide and lanthanum chloride, especially for remote sensing, low-level counting applications or any type of measurement characterized by poor signal to noise ratios. The Russian Space Research Institute has developed and manufactured a highly sensitive gamma-ray spectrometer for remote sensing observations of the planet Mercury from the Mercury Polar Orbiter (MPO), which forms part of ESA's BepiColombo mission. The Flight Model (FM) gamma-ray spectrometer is based on a 3-in. single crystal of LaBr3(Ce(3+)) produced in a separate crystal development programme specifically for this mission. During the spectrometers development, manufacturing, and qualification phases, large crystals of CeBr3 became available in a subsequent phase of the same crystal development programme. Consequently, the Flight Spare Model (FSM) gamma-ray spectrometer was retrofitted with a 3-in. CeBr3 crystal and qualified for space. Except for the crystals, the two systems are essentially identical. In this paper, we report on a comparative assessment of the two systems, in terms of their respective spectral properties, as well as their suitability for use in planetary mission with respect to radiation tolerance and their propensity for activation. We also contrast their performance with a Ge detector representative of that flown on MESSENGER and show that: (a) both LaBr3(Ce(3+)) and CeBr3 provide superior detection systems over HPGe in the context of minimally resourced spacecraft and (b) CeBr3 is a more attractive system than LaBr3(Ce(3+)) in terms of sensitivities at lower gamma fluxes. Based on the tests, the FM has now been replaced by the FSM on the BepiColombo spacecraft. Thus, CeBr3 now forms the central gamma-ray detection element on the MPO spacecraft.

Dissociative multiple photoionization of SiBr4 and GeBr4 in the VUV and X-ray regions: a comparative study of inner-shell processes involving Si(2p, 2s), Ge(3d, 3p, 3s), and Br(3d, 3p, 3s)

International Nuclear Information System (INIS)

Boo, Bong Hyun; Saito, Norio

2003-01-01

Dissociative multiple photoionization of MBr 4 (M=Si, Ge) in the Si(2p, 2s), Ge(3d, 3s, 3p), and Br(3d, 3p, 3s) inner-shell regions has been studied by using time-of-flight (TOF) mass spectrometry coupled to synchrotron radiation in the ranges of 50∼944 eV for SiBr 4 and 50∼467 eV for GeBr 4 . Total photoion and photoion-photoion coincidence (PIPICO) yields have been measured as functions of the photon energy. Here, giant shape resonances have been observed beyond the thresholds of the 3d shells owing to the Br(3d 10 )→Br(3d 9 -f) excitation, showing the similar patterns for both of the systems. The ranges and the intensities of the shape resonances are found to be tremendously broad and enhanced, respectively, by the tetrahedral arrangement of the bromine ligands. In addition to the giant resonances, we have observed discrete features corresponding to the Br(3d), Si(2p), and Si(2s) in SiBr 4 and to the Br(3d), Ge(3p), and Ge(3s) in GeBr 4 . The dissociation processes of multiply charged parent ions have also been evaluated from the variations of photoelectron-photoion coincidence (PEPICO) and PIPICO yields with the photon energy. Over the entire energies examined, most efficient PIPICO channels involve Br + -Br + , Br + -MBr + , and M + -Br + (M=Si, Ge), the formation of which indicates that the total destruction of the molecules is a dominant process in the dissociative photoionization of the molecules

Pyrolysis studies of PP/PE/PS/PVC/HIPS-Br plastics mixed with PET and dehalogenation (Br, Cl) of the liquid products

Energy Technology Data Exchange (ETDEWEB)

Bhaskar, Thallada; Kaneko, Jun; Muto, Akinori; Sakata, Yusaku [Department of Applied Chemistry, Faculty of Engineering, Okayama University, 3-1-1 Tsushima Naka, 700-8530 Okayama (Japan); Jakab, Emma [Research Laboratory of Materials and Environmental Chemistry, Chemical Research Center, Hungarian Academy of Sciences, P.O. Box 17, H-1525 Budapest (Hungary); Matsui, Toshiki [Toda Kogyo Co. Ltd., Hiroshima 739-0652 (Japan); Uddin, Md. Azhar [Process Safety and Environment Protection Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia)

2004-08-01

Pyrolysis of polypropylene (PP)/polyethylene (PE)/polystyrene (PS)/poly(vinyl chloride) (PVC)/high impact polystyrene with brominated flame retardant (HIPS-Br) plastics mixed with poly(ethylene terephthalate) (PET) was performed at 430C under atmospheric pressure using a semi-batch operation. The presence of PET in the pyrolysis mixture of PP/PE/PS/PVC/HIPS-Br affected significantly the formation of decomposition products and the decomposition behavior of the plastic mixture. We observed the following effects of PET on the pyrolysis of PP/PE/PS/PVC/HIPS-Br mixed plastics: (1) the yield of liquid product decreased and the formation of gaseous products increased; (2) a waxy residue was formed in addition to the solid carbon residue; (3) the formation of SbBr{sub 3} was not detected in liquid products; (4) the yield of chlorinated branched alkanes increased as well as vinyl bromide and ethyl bromide were formed. The use of calcium carbonate carbon composite (Ca-C) completely removed the chlorine and bromine content from the liquid products during PP/PE/PS/PVC/HIPS-Br pyrolysis, however in the presence of PET, the catalytic experiment (Ca-C, 8g) yielded liquid products containing 310ppm of Br and 20ppm of Cl. In addition, the Ca-C increased the yield of liquid products about 3-6wt.%, as well as enhanced the gaseous product evolution and decreased the yield of residue. The halogen free liquid hydrocarbons can be used as a feedstock in a refinery or as a fuel.

Synthesis and characterization of silver nanoparticle composite with poly(p-Br-phenylsilane).

Science.gov (United States)

Kim, Myoung-Hee; Lee, Jun; Mo, Soo-Yong; Woo, Hee-Gweon; Yang, Kap Seung; Kim, Bo-Hye; Lee, Byeong-Gweon; Sohn, Honglae

2012-05-01

The one-pot synthesis and characterization of silver nanoparticle-poly(p-Br-phenylsilane) composites have been carried out. The conversion of silver(+1) salt to stable silver(0) nanoparticles is promoted by poly(p-Br-phenylsilane), Br-PPS possessing both possible reactive Si-H bonds in the polymer backbone and C-Br bonds in the substituents. The composites were characterized using XRD, TEM, FE-SEM, and solid-state UV-vis analytical techniques. TEM and FE-SEM data show the formation of the composites where large number of silver nanoparticles (less than 30 nm of size) are well dispersed throughout the Br-PPS matrix. XRD patterns are consistent with that for fcc-typed silver. The elemental analysis for Br atom and the polymer solubility confirm that the cleavage of C-Br bond and the Si-Br dative bonding were not occurred appreciably at ambient temperature. Nonetheless, TGA data suggest that some sort of cross-linking was occurred at high temperature. The size and processability of such nanoparticles depend on the ratio of metal to Br-PPS. In the absence of Br-PPS, most of the silver particles undergo macroscopic aggregation, which indicates that the polysilane is necessary for stabilizing the silver nanoparticles.

Revised and extended analysis of Br IV

International Nuclear Information System (INIS)

Riyaz, A.; Rahimullah, K.; Tauheed, A.

2014-01-01

The spectrum of three-times ionized bromine Br IV has been studied in the 319–2350 Å wavelength region. The spectrum was recorded on a 3-m normal incidence vacuum spectrograph at the St. Francis Xavier University, Antigonish (Canada) and 6.65-m grazing incidence spectrograph at the Zeeman laboratory (Amsterdam). The light sources used were a triggered spark and sliding spark, respectively. The ground configuration of Br IV 3d 10 4s 2 4p 2 , the excited configurations 3d 10 4s4p 3 +3d 10 4s 2 4p (4d+5d+6d+5s+6s+7s) in the odd parity system and 3d 10 4s 2 4p (5p+4f+5f)+3d 10 4s4p 2 (4d+5s)+3d 10 4p 4 in the even parity system have been studied. Relativistic Hartree–Fock (HFR) and least squares fitted (LSF) parametric calculations were used to interpret the observed spectrum. 120 Levels of Br IV have now been established, 58 being new. Among 424 spectral lines, 277 are newly classified. The levels 4s4p 35 S 2 , 4s 2 4p4d 3 F 4 and 4p5p ( 3 P 0,1 , 3 D 1,2 , 3 S 1 ) are revised. We estimate the accuracy of our measured wavelength for sharp and unblended lines to be ±0.005 Å. The ionization limit is determined as 385,390±100 cm −1 (47.782±0.012 eV). -- Highlights: • The spectrum of Br was recorded on a 3-m spectrograph with triggered spark source. • Atomic transitions for Br IV were identified to established new energy levels. • CI calculations with relativistic corrections were made for theoretical predictions. • Weighted oscillator strength (gf) and transition probabilities (gA) were calculated. • Ionization potential of Br IV was determined experimentally

Formation of new halogenothiocarbonylsulfenyl halides, XC(S)SY, through photochemical matrix reactions starting from CS2 and a dihalogen molecule XY (XY=Cl2, Br2, or BrCl).

Science.gov (United States)

Tobón, Yeny A; Romano, Rosana M; Védova, Carlos O Della; Downs, Anthony J

2007-05-28

Isolation of a dihalogen molecule XY (XY=Cl2, Br2, or BrCl) with CS2 in a solid Ar matrix at about 15 K leads, by broad-band UV-vis photolysis (200BrC(S)Cl, BrCCl3, and :CBrCl, the following new molecules have also been identified as products of the various photoreactions: syn-ClC(S)SCl, anti-ClC(S)SCl, syn-BrC(S)SBr, anti-BrC(S)SBr, syn-ClC(S)SBr, anti-ClC(S)SBr, syn-BrC(S)SCl, anti-BrC(S)SCl, ClC(S)S*, BrCS*, and Br*...SCS. The IR spectra of these hitherto unknown species have been interpreted with reference to the predictions of ab initio (HF and MP2) and density functional theory (DFT) calculations. The results are analyzed in relation to the reaction pathways accessed by matrix photolysis.

High Defect Tolerance in Lead Halide Perovskite CsPbBr3.

Science.gov (United States)

Kang, Jun; Wang, Lin-Wang

2017-01-19

The formation energies and charge-transition levels of intrinsic point defects in lead halide perovskite CsPbBr 3 are studied from first-principles calculations. It is shown that the formation energy of dominant defect under Br-rich growth condition is much lower than that under moderate or Br-poor conditions. Thus avoiding the Br-rich condition can help to reduce the defect concentration. Interestingly, CsPbBr 3 is found to be highly defect-tolerant in terms of its electronic structure. Most of the intrinsic defects induce shallow transition levels. Only a few defects with high formation energies can create deep transition levels. Therefore, CsPbBr 3 can maintain its good electronic quality despite the presence of defects. Such defect tolerance feature can be attributed to the lacking of bonding-antibonding interaction between the conduction bands and valence bands.

Brändin nykytila ja kehityskohtien identifiointi : case: Yritys X

OpenAIRE

Leinonen, Joonas

2017-01-01

Tämän opinnäytetyön tavoitteena on selvittää Yritys X:n brändin nykytila sekä identifioida eli tunnistaa sen heikkoudet sekä ryhmät, joiden keskuudessa brändimielikuva on heikompi. Tarkoituksena on käytännössä tarjota yritykselle osuus brändistrategiasuunnitelmasta, jonka avulla se pystyy keskittämään brändinehostustoimenpiteensä tiettyihin asioihin ja ryhmiin. Opinnäytetyön tutkimus suoritettiin määrällisenä tutkimuksena, sillä tavoitteena oli saada selville suuren yleisön käsitys Yrity...

Single crystal growth and surface chemical stability of KPb2Br5

Science.gov (United States)

Atuchin, V. V.; Isaenko, L. I.; Kesler, V. G.; Tarasova, A. Yu.

2011-03-01

Single crystal of KPb2Br5 has been grown using the Bridgman technique. Initially the synthesis of stoichiometric KPb2Br5 compound was performed from high purity bromide salts. Electronic structure of KPb2Br5 has been determined with X-ray photoelectron spectroscopy for powdered sample fabricated by grinding in air. Drastic chemical interaction of KPb2Br5 with atmosphere has not been detected. Chemical bonding in potassium- and lead-containing bromides is considered using binding energy differences ΔK=(BE K 2p3/2-BE Br 3d) and ΔPb=(BE Pb 4f7/2-BE Br 3d), respectively, as representative parameters.

PbBr3 Perovskite Crystals

KAUST Repository

Wei, Tzu-Chiao

2018-01-31

Researchers have recently revealed that hybrid lead halide perovskites exhibit ferroelectricity, which is often associated with other physical characteristics, such as a large nonlinear optical response. In this work, the nonlinear optical properties of single crystal inorganic–organic hybrid perovskite CH3NH3PbBr3 are studied. By exciting the material with a 1044 nm laser, strong two-photon absorption-induced photoluminescence in the green spectral region is observed. Using the transmission open-aperture Z-scan technique, the values of the two-photon absorption coefficient are observed to be 8.5 cm GW−1, which is much higher than that of standard two-photon absorbing materials that are industrially used in nonlinear optical applications, such as lithium niobate (LiNbO3), LiTaO3, KTiOPO4, and KH2PO4. Such a strong two-photon absorption effect in CH3NH3PbBr3 can be used to modulate the spectral and spatial profiles of laser pulses, as well as to reduce noise, and can be used to strongly control the intensity of incident light. In this study, the superior optical limiting, pulse reshaping, and stabilization properties of CH3NH3PbBr3 are demonstrated, opening new applications for perovskites in nonlinear optics.

Measurement of BR(Bu to phi K)/BR(Bu to J/psi K) at the collider detector at Fermilab

Energy Technology Data Exchange (ETDEWEB)

Napora, Robert A. [Johns Hopkins Univ., Baltimore, MD (United States)

2004-01-01

This thesis presents evidence for the decay mode B^± → ΦK^± in p$\\bar{p}$ collisions at √s = 1.96 TeV using (120 ± 7)pb^-1 of data collected by the Collider Detector at Fermilab (CDF). This signal is then used to measure the branching ratio relative to the decay mode B^± → J/ΨK^±. The measurement starts from reconstructing the two decay modes: B^± → ΦK^±, where Φ → K⁺K^- and B^± → J/ΨK^±, where J/Ψ → μ⁺μ^-. The measurement yielded 23 ± 7 B^± → ΦK^± events, and 406 ± 26 B^± → J/ΨK^± events. The fraction of B^± → J/ΨK^± events where the J/Ψ subsequently decayed to two muons (as opposed to two electrons) was found to be f_μμ = 0.839 ± 0.066. The relative branching ratio of the two decays is then calculated based on the equation: BR(B^± → ΦK^±)/BR(B^± → J/ΨK^±) = N _ΦK/N_ΨK • f_μμ BR(J/Ψ → μ⁺μ^-)/BR(Φ → K⁺K^-) ϵ_μμK/ϵKKK R(ϵ_iso). The measurement finds BR(B^± → ΦK^±)/BR(B^± → J/ΨK^±) = 0.0068 ± 0.0021(stat.) ± 0.0007(syst.). The B^± → ΦK^± branching ratio is then found to be BR(B^± → ΦK^±) = [6.9 ± 2.1(stat.) ± 0.8(syst.)] x 10^-6. This value is consistent with similar measurements reported by the e⁺e^- collider experiments BaBar[1], Belle[2], and CLEO[3].

thermal, electrical and structural characterization of fast ion conducting glasses (Ag Br)x(AgPO)1-x

International Nuclear Information System (INIS)

Kartini, E.; Yufus, S.; Priyanto, T; Indayaningsih, N; Collins, M F

2001-01-01

Fast ion conducting glasses are of considerable technological interest because of their possible application in batteries, sensors, and displays. One of the main scientific challenges is to explain how the disordered structure of the glass is related to the high ionic conductivity that can be achieved at ambient temperature. Fast ion conducting glasses (AgBr) x (AgPO3) 1- x with x=0.0; 0.2; 0.3; 0.4; 0.5; 0.7; and 0.85 were prepared by rapid quenching. The studies of structure, thermal property and electrical conductivity have been made. The X-ray diffraction patterns of this system show that the sample are glasses for x 0.5. The neutron diffraction data shows that all AgBr doped glasses exhibit a strong and relatively sharp diffraction peak at anomalously low momentum transfer value, Q∼ 0.7 Α - 1. The low Q-peak is not observed in AgPO 3 glass, and in the X-ray data. The results of electrical conductivity show that the conduction is essentially ionic and due to silver ions alone. The logarithm of the ionic conductivity increases with increasing AgBr mole fraction, and reaches maximum for x = 0.5. The thermal property results measured by differential scanning calorimetric show that the temperatures of the glass transition, the crystallization and the melt reach minimum for the glass with composition x 0.5. We conclude that there appears to be a relation between higher conductivity at ambient temperature, and the low Q-peak. Based on this investigation a better fast ion conducting glass proposed is (AgBr) 0 .5(AgPO 3 ) 0 .5 with the conductivity of 8 x 10 - 5 S/cm

Inhibition of hydrogen oxidation by HBr and Br₂

DEFF Research Database (Denmark)

Dixon-Lewis, Graham; Marshall, Paul; Ruscic, Branko

2012-01-01

O. Ab initio calculations were used to obtain rate coefficients for selected reactions of HBr and HOBr, and the hydrogen/bromine/oxygen reaction mechanism was updated. The resulting model was validated against selected experimental data from the literature and used to analyze the effect of HBr and Br2......The high-temperature bromine chemistry was updated and the inhibition mechanisms involving HBr and Br2 were re-examined. The thermochemistry of the bromine species was obtained using the Active Thermochemical Tables (ATcT) approach, resulting in improved data for, among others, Br, HBr, HOBr and Br...... on laminar, premixed hydrogen flames. Our work shows that hydrogen bromide and molecular bromine act differently as inhibitors in flames. For HBr, the reaction HBr+H⇌H2+Br (R2) is rapidly equilibrated, depleting HBr in favor of atomic Br, which is the major bromine species throughout the reaction zone...

Neutron diffraction study of structural changes in ammonium halides ND4Br and ND4Cl under high pressure

International Nuclear Information System (INIS)

Balagurov, A.M.; Kozlenko, D.P.; Savenko, B.N.; Glazkov, V.P.; Somenkov, V.A.

1997-01-01

Structural changes in ammonium halides ND 4 Br and ND 4 Cl at pressures up to 45 kbar and up to 35 kbar, respectively, have been studied with the DN-12 diffractometer at the IBR-2 pulsed reactor. For both systems, the equation of state and the position parameter of deuterium atoms as functions of pressure were obtained. The obtained equations of state are nearly the same as the ones for the nondeuterated systems NH 4 Br and NH 4 Cl obtained by the piston displacement technique. It was found that the order - disorder phase transition from the phase in which the ammonium tetrahedra are randomly oriented (CsCl-type cubic structure, space group Pm3m) into the phase in which the ammonium tetrahedra are oriented in parallel (CsCl-type cubic structure, space group P4 bar 3m), occurs at equal critical value of the position parameter u=0.153 ± 0.002 in both systems. It appears to be valid for all of the ammonium halides, and, possibly, for other similar compounds. (author)

Safety aspects of using gadolinium as burnable poison in pressurized water reactors

International Nuclear Information System (INIS)

Vandenberg, C.; Bonet, H.; Charlier, A.; Motte, F.

1979-01-01

Within the framework of an experimental program on the behavior of gadolinium in light water reactors (LWRs), the BR3 power plant, a small 11-MW(electric) pressurized water reactor, was operated successfully with a core containing 5% Gd 2 O 3 -UO 2 rods. The core reached an average burnup increase of 22,000 MWd/tM, corresponding to 500 effective full-power days in a single cycle. These results were used to extrapolate the consequences on safety of extending such a control policy to large LWRs. In this context, the following factors were investigated: impact on the design, reactivity control and core behavior operated with lower and more constant boric acid concentration, environmental impact, fuel handling, etc

Overview of gamma-ray energy deposition and spectra in fast reactor environments

International Nuclear Information System (INIS)

Gold, R.

1977-01-01

Efforts to define gamma-ray heating in Breeder Reactor (BR) environments are reviewed. This critique is restricted to programmatic activities in the United States, as best exemplified by current practice for the Experimental Breeder Reactor II (EBR-II). Future needs are also addressed in terms of requirements for the Fast Flux Test Facility (FFTF). Experimental efforts and theoretical analyses are surveyed for both high and low power environments. Special emphasis is placed on experimental techniques for calorimetry, temperature measurement, dosimetry and spectrometry. The relation between neutron and gamma-ray calculations is stressed with particular attention given to contrasting analytical techniques and basic nuclear data requirements. Wherever possible comparisons between theory and experiment are cited

Picosecond Water Radiolysis at High Temperature. Br- Oxidation - Experiments and MC-Simulations

International Nuclear Information System (INIS)

Baldacchino, G.; Saffre, D.; Jeunesse, J.P.; Schmidhammer, U.; Larbre, J.P.; Mostafavi, M.; Beuve, M.; Gervais, B.

2012-09-01

Acidic solutions of bromhydric acid have been irradiated by picosecond pulses of 7 MeV-electrons provided by ELYSE accelerator (LCP Orsay). At elevated temperatures up to 350 deg. C, salts like NaBr or KBr usually precipitate and organic compound are decomposed. Another choice of OH-scavenger may be acidic halogenates like HBr or HCl. In this situation, the processes involving H + and Br - must be considerate: while hydrated electrons are scavenged by H + , . OH reacts with Br - . Then the formations of BrOH . and Br 2 .- have been investigated by using a devoted picosecond pump-probe setup. A dedicated small-size high temperature optical flow cell has been developed for fitting the picosecond duration of the electron pulses. This cell replaces the one used also with nanosecond resolution. The picosecond time resolution remains roughly not affected by the material crossed by electrons (0.4 mm of Inconel 718) and by the white light continuum (20 mm of Sapphire windows and 6 mm of liquid solution). Depending on the concentration of HBr, the growing up of the signal can be attributed to mainly BrOH . or Br2 .- . Actually with a relatively low scavenging power ([HBr] = 25 mM), Br 2 .- is formed with a reaction between Br . and Br - which delays of around 4 ns the apparition of Br2 .- . In this particular case we then assume the absorbance is due to BrOH . . With higher and higher temperature, from 100 deg. C to 300 deg. C, the rate constant of this formation is lightly less and less. This observation must be associated to the fact that the formation of BrOH . is actually equilibrium with a lower and lower equilibrium constant value when temperature is increased. This presentation tries to explain this fact in detail by also considering Monte Carlo simulations. This will allows following all transient species from ps to μs. (authors)

The First Benchmarking of ITER BR Nb3Sn Strand of CNDA

International Nuclear Information System (INIS)

Long Feng; Liu Fang; Wu Yu; Ni Zhipeng

2012-01-01

According to the International Thermonuclear Experimental Reactor (ITER) Procurement Arrangement (PA) of Cable-In-Conduit Conductor (CICC) unit lengths for the Toroidal Field (TF) and Poloidal Field (PF) magnet systems of ITER, at the start of process qualification, the Domestic Agency (DA) shall be required to conduct a benchmarking of the room and low temperature acceptance tests carried out at the Strand Suppliers and/or at its Reference Laboratories designated by the ITER Organization (IO). The first benchmarking was carried out successfully in 2009. Nineteen participants from six DAs (China, European Union, Japan, South Korea, Russia, and the United States) participated in the first benchmarking. Bronze-route (BR) Nb 3 Sn strand and samples prepared by the ITER reference lab (CERN) were sent out to each participant by CERN. In this paper, the test facility and test results of the first benchmarking by the Chinese DA (CNDA) are presented.

Br2 induced oxidative pore modification of a porous coordination network.

Science.gov (United States)

Ohtsu, Hiroyoshi; Kawano, Masaki

2016-01-14

Iodinated pores of a Zn-based coordination network were modified by Br2 oxidation to produce brominated pores in a polycrystalline-to-polycrystalline manner while maintaining the same network topology. Ab initio X-ray powder diffraction analysis and Raman spectroscopy revealed that the brominated pore can trap Br2 or I2 by strong σ/π-type interactions. A kinetic study in solution revealed that the pore modification by Br2 oxidation is much faster than the Br2 encapsulation process.

Polymorphism in 2-X-adamantane derivatives (X = Cl, Br).

Science.gov (United States)

Negrier, Philippe; Barrio, María; Tamarit, Josep Ll; Mondieig, Denise

2014-08-14

The polymorphism of two 2-X-adamantane derivatives, X = Cl, X = Br, has been studied by X-ray powder diffraction and normal- and high-pressure (up to 300 MPa) differential scanning calorimetry. 2-Br-adamantane displays a low-temperature orthorhombic phase (space group P212121, Z = 4) and a high-temperature plastic phase (Fm3̅m, Z = 4) from 277.9 ± 1.0 K to the melting point at 413.4 ± 1.0 K. 2-Cl-adamantane presents a richer polymorphic behavior through the temperature range studied. At low temperature it displays a triclinic phase (P1̅, Z = 2), which transforms to a monoclinic phase (C2/c, Z = 8) at 224.4 ± 1.0 K, both phases being ordered. Two high-temperature orientationally disordered are found for this compound, one hexagonal (P63/mcm, Z = 6) at ca. 241 K and the highest one, cubic (Fm3̅m, Z = 4), being stable from 244 ± 1.0 K up to the melting point at 467.5 ± 1.0 K. No additional phase appears due to the increase in pressure within the studied range. The intermolecular interactions are found to be weak, especially for the 2-Br-adamantane compound for which the Br···Br as well as C-Br···H distances are larger than the addition of the van der Waals radii, thus confirming the availability of this compound for building up diamondoid blocks.

CeBr3 as a room-temperature, high-resolution gamma-ray detector

International Nuclear Information System (INIS)

Guss, Paul; Reed, Michael; Yuan Ding; Reed, Alexis; Mukhopadhyay, Sanjoy

2009-01-01

Cerium bromide (CeBr 3 ) has become a material of interest in the race for high-resolution gamma-ray spectroscopy at room temperature. This investigation quantified the potential of CeBr 3 as a room-temperature, high-resolution gamma-ray detector. The performance of CeBr 3 crystals was compared to other scintillation crystals of similar dimensions and detection environments. Comparison of self-activity of CeBr 3 to cerium-doped lanthanum tribromide (LaBr 3 :Ce) was performed. Energy resolution and relative intrinsic efficiency were measured and are presented.

Identification of Yellow Pigmentation Genes in Brassica rapa ssp. pekinensis Using Br300 Microarray

Directory of Open Access Journals (Sweden)

Hee-Jeong Jung

2014-01-01

Full Text Available The yellow color of inner leaves in Chinese cabbage depends on its lutein and carotene content. To identify responsible genes for yellow pigmentation in leaves, the transcriptome profiles of white (Kenshin and yellow leaves (Wheessen were examined using the Br300K oligomeric chip in Chinese cabbage. In yellow leaves, genes involved in carotene synthesis (BrPSY, BrPDS, BrCRTISO, and BrLCYE, lutein, and zeaxanthin synthesis (BrCYP97A3 and BrHYDB were upregulated, while those associated with carotene degradation (BrNCED3, BrNCED4, and BrNCED6 were downregulated. These expression patterns might support that the content of both lutein and total carotenoid was much higher in the yellow leaves than that in the white leaves. These results indicate that the yellow leaves accumulate high levels of both lutein and β-carotene due to stimulation of synthesis and that the degradation rate is inhibited. A large number of responsible genes as novel genes were specifically expressed in yellow inner leaves, suggesting the possible involvement in pigment synthesis. Finally, we identified three transcription factors (BrA20/AN1-like, BrBIM1, and BrZFP8 that are specifically expressed and confirmed their relatedness in carotenoid synthesis from Arabidopsis plants.

Structure and bonding of transition metal-boryl compounds. Theoretical study of [(PH3)2(CO)ClOs-BR2] and [(PH3)2(CO)2ClOs-BR2] (BR2 = BH2, BF2, B(OH)2, B(OCH=CHO), Bcat).

Science.gov (United States)

Giju, K T; Bickelhaupt, F M; Frenking, G

2000-10-16

Quantum chemical DFT calculations using the B3LYP functionals have been carried out for the electronically unsaturated 16 VE five-coordinate osmium boryl-complexes [(PH3)2(CO)ClOs-BR2] and the 18 VE six-coordinate complexes [(PH3)2(CO)2ClOs-BR2] with BR2 = BH2, BF2, B(OH)2, B(OHC=CHO), and Bcat (cat = catecholate O2C6H4). The bonding situation of the Os-BR2 bond was analyzed with the help of the NBO partitioning scheme. The Os-B bond dissociation energies of the 16 VE complexes are very high, and they do not change very much for the different boryl ligands. The 18 VE complexes have only slightly lower bond energies than the 16 VE species. The Os-B bond in both classes of compounds is provided by a covalent sigma-bond which is polarized toward osmium and by strong charge attraction. Os-->B pi-donation is not important for the Os-B binding interactions, except for the Os-BH2 complexes. The stability of the boryl complexes [Os]-BR2 comes mainly from BB pi-donation. The intraligand charge distribution of the BR2 group changes little when the Os-B bond is formed, except for BH2. The CO ligand in [(PH3)2(CO)2ClOs-BR2] which is trans to BR2 has a relatively weak bond to the osmium atom.

Magnetic diagnostic plasma position in the TCA/BR tokamak

International Nuclear Information System (INIS)

Galvao, R.M.O.; Kuznetsov, Yu.K.; Nascimento, I.C.

1996-01-01

The cross-section of the plasma column is TCA/BR has a nearly circular plasma shape. This allows implementation of simplified methods of magnetic diagnostics. Although these methods were in may tokamaks and are well described, their accuracies are not clearly defined because the very simplified theoretical model of plasma equilibrium on which they are based differs from the real conditions in tokamaks like TCA/BR. In this paper we present the methods of plasma position diagnostics in TCA/BR from external magnetic measurements with an error analysis. (author). 4 refs., 3 figs

Measuring temperature coefficient of TRIGA MARK I reactor by noise analysis

International Nuclear Information System (INIS)

Soares, P.A.

1975-01-01

The transfer function of TRIGA MARK I Reactor is measured at power zero (5w) and power 118Kw, in the frequency range of 0.02 to 0.5 rd/s. The method of intercorrelation between a pseudostochasticbinary signal is used. A simple dynamic model of the reactor is developed and the coefficient of temperature is estimated [pt

Retrieval of stratospheric and tropospheric BrO profiles and columns using ground-based zenith-sky DOAS observations at Harestua, 60° N

Directory of Open Access Journals (Sweden)

J. A. Pyle

2007-09-01

Full Text Available A profiling algorithm based on the optimal estimation method is applied to ground-based zenith-sky UV-visible measurements from Harestua, Southern Norway (60° N, 11° E in order to retrieve BrO vertical profiles. The sensitivity of the zenith-sky observations to the tropospheric BrO detection is increased by using for the spectral analysis a fixed reference spectrum corresponding to clear-sky noon summer conditions. The information content and retrieval errors are characterized and it is shown that the retrieved stratospheric profiles and total columns are consistent with correlative balloon and satellite observations, respectively. Tropospheric BrO columns are derived from profiles retrieved at 80° solar zenith angle during sunrise and sunset for the 2000–2006 period. They show a marked seasonality with mean column value ranging from 1.52±0.62×1013 molec/cm² in late winter/early spring to 0.92±0.38×1013 molec/cm² in summer, which corresponds to 1.0±0.4 and 0.6±0.2 pptv, respectively, if we assume that BrO is uniformly mixed in the troposphere. These column values are also consistent with previous estimates made from balloon, satellite, and other ground-based observations. Daytime (10:30 LT tropospheric BrO columns are compared to the p-TOMCAT 3-D tropospheric chemical transport model (CTM for the 2002–2003 period. p-TOMCAT shows a good agreement with the retrieved columns except in late winter/early spring where an underestimation by the model is obtained. This finding could be explained by the non-inclusion of sea-ice bromine sources in the current version of p-TOMCAT. Therefore the model cannot reproduce the possible transport of air-masses with enhanced BrO concentration due to bromine explosion events from the polar region to Harestua. The daytime stratospheric BrO columns are compared to the SLIMCAT stratospheric 3-D-CTM. The model run used in this study, which assumes 21.2 pptv for the Bry loading (15 pptv for long

Global observations of tropospheric BrO columns using GOME-2 satellite data

Science.gov (United States)

Theys, N.; van Roozendael, M.; Hendrick, F.; Yang, X.; de Smedt, I.; Richter, A.; Begoin, M.; Errera, Q.; Johnston, P. V.; Kreher, K.; de Mazière, M.

2011-02-01

Measurements from the GOME-2 satellite instrument have been analyzed for tropospheric BrO using a residual technique that combines measured BrO columns and estimates of the stratospheric BrO content from a climatological approach driven by O3 and NO2 observations. Comparisons between the GOME-2 results and BrO vertical columns derived from correlative ground-based and SCIAMACHY nadir observations, present a good level of consistency. We show that the adopted technique enables separation of stratospheric and tropospheric fractions of the measured total BrO columns and allows quantitative study of the BrO plumes in polar regions. While some satellite observed plumes of enhanced BrO can be explained by stratospheric descending air, we show that most BrO hotspots are of tropospheric origin, although they are often associated to regions with low tropopause heights as well. Elaborating on simulations using the p-TOMCAT tropospheric chemical transport model, this result is found to be consistent with the mechanism of bromine release through sea salt aerosols production during blowing snow events. No definitive conclusion can be drawn however on the importance of blowing snow sources in comparison to other bromine release mechanisms. Outside polar regions, evidence is provided for a global tropospheric BrO background with column of 1-3 × 1013 molec cm-2, consistent with previous estimates.

Physical adsorption and charge transfer of molecular Br2 on graphene.

Science.gov (United States)

Chen, Zheyuan; Darancet, Pierre; Wang, Lei; Crowther, Andrew C; Gao, Yuanda; Dean, Cory R; Taniguchi, Takashi; Watanabe, Kenji; Hone, James; Marianetti, Chris A; Brus, Louis E

2014-03-25

We present a detailed study of gaseous Br2 adsorption and charge transfer on graphene, combining in situ Raman spectroscopy and density functional theory (DFT). When graphene is encapsulated by hexagonal boron nitride (h-BN) layers on both sides, in a h-BN/graphene/h-BN sandwich structure, it is protected from doping by strongly oxidizing Br2. Graphene supported on only one side by h-BN shows strong hole doping by adsorbed Br2. Using Raman spectroscopy, we determine the graphene charge density as a function of pressure. DFT calculations reveal the variation in charge transfer per adsorbed molecule as a function of coverage. The molecular adsorption isotherm (coverage versus pressure) is obtained by combining Raman spectra with DFT calculations. The Fowler-Guggenheim isotherm fits better than the Langmuir isotherm. The fitting yields the adsorption equilibrium constant (∼0.31 Torr(-1)) and repulsive lateral interaction (∼20 meV) between adsorbed Br2 molecules. The Br2 molecule binding energy is ∼0.35 eV. We estimate that at monolayer coverage each Br2 molecule accepts 0.09 e- from single-layer graphene. If graphene is supported on SiO2 instead of h-BN, a threshold pressure is observed for diffusion of Br2 along the (somewhat rough) SiO2/graphene interface. At high pressure, graphene supported on SiO2 is doped by adsorbed Br2 on both sides.

Study on the transient behaviours of MNSR reactor for control rod withdrawal

International Nuclear Information System (INIS)

Yang Shunhai

1995-10-01

The transient behaviours of Miniature Neutron Source Reactor MNSR are analyzed and calculated with the reactor thermohydraulics RETRAN-02 program and the reactor physics MARIA program. The obtained event sequence and consequence from the calculation are compared with the experiments. The effective resonance integral for study on Doppler effect is taken into account. The reactivity temperature coefficient weighting factors are computed. The transient parameters related to reactor power peaking, coolant inlet temperatures, outlet temperatures and coolant mass flow, etc. are computed and compared with the experimental results. (6 refs., 2 figs., 5 tabs.)

Pulse radiolysis of LiBr-KBr melts. Optical transient absorption spectra

International Nuclear Information System (INIS)

Sawamura, S.; Gebicki, J.L.; Mayer, J.; Kroh, J.

1990-01-01

Absorption spectra of the irradiated melts of LiBr and LiBr-KBr mixtures were investigated in the temperature range 673-873 K by nanosecond pulse radiolysis. The visible band ascribed to e s - shows the apparent shift towards longer wavelengths with increasing temperature and increasing content of KBr in the mixture. The UV transient absorption was attributed to superimposed Br 2 - and Br 3 - bands. The relation between the transition energy of visible band and the inverse mean ion distance is given for alkali bromide and chloride systems. (author)

Global observations of BrO in the troposphere using GOME-2 satellite data

Science.gov (United States)

Theys, N.; van Roozendael, M.; Hendrick, F.; Xin, Y.; Isabelle, D.; Richter, A.; Mathias, B.; Quentin, E.; Johnston, P. V.; Kreher, K.; Martine, D.

2010-12-01

Measurements from the GOME-2 satellite instrument have been analyzed for tropospheric BrO using a residual technique that combines measured BrO columns and estimates of the stratospheric BrO content from a climatological approach driven by O3 and NO2 observations. Comparisons between the GOME-2 results and correlative data including ground-based BrO vertical columns and total BrO columns derived from SCIAMACHY nadir observations, present a good level of consistency. We show that the adopted technique enables to separate the stratospheric and tropospheric fractions of the measured total BrO columns and allows studying the BrO plumes in polar region in more detail. While several satellite BrO plumes can largely be explained by an influence of stratospheric descending air, we show that numerous tropospheric BrO hotspots are associated to regions with low tropopause heights as well. Elaborating on simulations using the p-TOMCAT tropospheric chemical transport model, this finding is found to be consistent with the mechanism of bromine release through sea salt aerosols production during blowing snow events. Outside the polar region, evidences are provided for a global tropospheric BrO background with columns of 1-3 x 1013 molec/cm2.

Structure determination of K2ZnBr4 at 291 and 144 K

International Nuclear Information System (INIS)

Fabry, J.; Breczewski, T.; Zuniga, F.J.; Arnaiz, A.R.

1993-01-01

The room-temperature phase of K 2 ZnBr 4 is isomorphous with Sr 2 GeS 4 (P2 1 /m) while the low-temperature structure (P2 1 ) is slightly distorted [the phase transition occurs at 155 K]. Both structures contain highly deformed tetrahedral [ZnBr 4 ] 2- molecules with Br(3)-Zn-Br(3') angles of 103.06(5) and 102.49(9) at 291 and 144 K, respectively. This distortion is caused by the repulsion of Br atoms whose distance 3.712(1) and 3.661(2) A at 291 and 144 K, respectively, is below the Br-Br van der Waals distance (3.9 A). The phase transition is accompanied by minor shifts of cations and [ZnBr 4 ] 2- tetrahedra which are simultaneously rotated about a small angle. Below the phase transition point an inversion twin develops whose twin-fraction parameter was refined to 0.459(65). (orig.)

Kan lignin omdannes til flydende brændstof?

DEFF Research Database (Denmark)

Nielsen, Joachim Bachmann; Jensen, Anders; Felby, Claus

2015-01-01

Ved en solvolytisk omdannelse af plantematerialet lignin til et flydende brændstof behandles det ved høj temperatur og højt tryk i et passende opløsningsmiddel. En sådan proces kan gennemføres ikke-katalytisk og være med til at skabe flydende brændsler baseret på vedvarende energikilder. Her...

Propiconazole is a specific and accessible brassinosteroid (BR) biosynthesis inhibitor for Arabidopsis and maize.

Science.gov (United States)

Hartwig, Thomas; Corvalan, Claudia; Best, Norman B; Budka, Joshua S; Zhu, Jia-Ying; Choe, Sunghwa; Schulz, Burkhard

2012-01-01

Brassinosteroids (BRs) are steroidal hormones that play pivotal roles during plant development. In addition to the characterization of BR deficient mutants, specific BR biosynthesis inhibitors played an essential role in the elucidation of BR function in plants. However, high costs and limited availability of common BR biosynthetic inhibitors constrain their key advantage as a species-independent tool to investigate BR function. We studied propiconazole (Pcz) as an alternative to the BR inhibitor brassinazole (Brz). Arabidopsis seedlings treated with Pcz phenocopied BR biosynthetic mutants. The steady state mRNA levels of BR, but not gibberellic acid (GA), regulated genes increased proportional to the concentrations of Pcz. Moreover, root inhibition and Pcz-induced expression of BR biosynthetic genes were rescued by 24epi-brassinolide, but not by GA(3) co-applications. Maize seedlings treated with Pcz showed impaired mesocotyl, coleoptile, and true leaf elongation. Interestingly, the genetic background strongly impacted the tissue specific sensitivity towards Pcz. Based on these findings we conclude that Pcz is a potent and specific inhibitor of BR biosynthesis and an alternative to Brz. The reduced cost and increased availability of Pcz, compared to Brz, opens new possibilities to study BR function in larger crop species.

Facile synthesis and characterization of CsPbBr3 and CsPb2Br5 ...

Indian Academy of Sciences (India)

2018-03-23

Mar 23, 2018 ... All-inorganic caesium lead-halide perovskite CsPbBr3 and ... optoelectronic materials owing to their stabilities and highly efficient photoluminescence (PL). ... chemical tenability [2], hybrid organic–inorganic lead halide-.

Global observations of tropospheric BrO columns using GOME-2 satellite data

Directory of Open Access Journals (Sweden)

N. Theys

2011-02-01

Full Text Available Measurements from the GOME-2 satellite instrument have been analyzed for tropospheric BrO using a residual technique that combines measured BrO columns and estimates of the stratospheric BrO content from a climatological approach driven by O₃ and NO₂ observations. Comparisons between the GOME-2 results and BrO vertical columns derived from correlative ground-based and SCIAMACHY nadir observations, present a good level of consistency. We show that the adopted technique enables separation of stratospheric and tropospheric fractions of the measured total BrO columns and allows quantitative study of the BrO plumes in polar regions. While some satellite observed plumes of enhanced BrO can be explained by stratospheric descending air, we show that most BrO hotspots are of tropospheric origin, although they are often associated to regions with low tropopause heights as well. Elaborating on simulations using the p-TOMCAT tropospheric chemical transport model, this result is found to be consistent with the mechanism of bromine release through sea salt aerosols production during blowing snow events. No definitive conclusion can be drawn however on the importance of blowing snow sources in comparison to other bromine release mechanisms. Outside polar regions, evidence is provided for a global tropospheric BrO background with column of 1–3 × 10¹³ molec cm⁻², consistent with previous estimates.

Bromide (Br)--Based Synthesis of Ag Nanocubes with High-Yield.

Science.gov (United States)

Wu, Fan; Wang, Wenhui; Xu, Zhongfeng; Li, Fuli

2015-06-09

The geometry of metal nanoparticles greatly affects the properties of the localized surface plasmon resonance and surface-enhanced Raman scattering. The synthesis of metal nanoparticles with controllable geometry has thus attracted extensive attentions. In this work, we report a modified polyol synthesis approach of silver (Ag) nanocubes through tuning the concentration of bromide ions (Br(-) ions). We have systematically investigated the effect of Br(-) ions in the polyol process, and find that higher concentration of Br(-) ions can enhance oxidative etching effect, which is the dominative factor in determining nanostructure geometry. Therefore, one can realize control over nanostructure geometry by manipulating the concentration of Br(-) ions. Our work provides an effective approach to control the shape of metallic nanostructures for potential applications.

Steering dissociation of Br2 molecules with two femtosecond pulses via wave packet interference.

Science.gov (United States)

Han, Yong-Chang; Yuan, Kai-Jun; Hu, Wen-Hui; Yan, Tian-Min; Cong, Shu-Lin

2008-04-07

The dissociation dynamics of Br2 molecules induced by two femtosecond pump pulses are studied based on the calculation of time-dependent quantum wave packet. Perpendicular transition from X 1Sigma g+ to A 3Pi 1u+ and 1Pi 1u+ and parallel transition from X 1Sigma g+ to B 3Pi 0u+, involving two product channels Br (2P3/2)+Br (2P3/2) and Br (2P3/2)+Br* (2P1/2), respectively, are taken into account. Two pump pulses create dissociating wave packets interfering with each other. By varying laser parameters, the interference of dissociating wave packets can be controlled, and the dissociation probabilities of Br2 molecules on the three excited states can be changed to different degrees. The branching ratio of Br*/(Br+Br*) is calculated as a function of pulse delay time and phase difference.

Self-Powered Neutron Detector Qualification for Absolute On-Line In-Pile Neutron Flux Measurements in BR2

Science.gov (United States)

Vermeeren, L.; Wéber, M.

2003-06-01

A set of ten Self-Powered Neutron Detectors with Co, Rh and Ag emitters has been irradiated in several channels of the BR2 research reactor at SCK•CEN aiming at a comparison of their performance as thermal neutron flux detectors under various conditions. To allow for a correct interpretation of their signals, all detector sensitivity contributions (prompt and delayed) were calculated using a dedicated Monte Carlo model. The various contributions were also measured separately; the agreement between calculated and experimental data, including data from activation dosimetry, was excellent. Detailed neutron flux profiles were obtained from the SPND data, after correction for the finite detector lengths and for the slow response of delayed SPNDs.

From high enriched to low enriched uranium fuel in research reactors

Energy Technology Data Exchange (ETDEWEB)

Van Den Berghe, S.; Leenaers, A.; Koonen, E.; Moons, F.; Sannen, L. [Nuclear Materials Science Institute, SCK.CEN, Boeretang 200, B-2400 Mol (Belgium)

2010-07-01

Since the 1970's, global efforts have been going on to replace the high-enriched (>90% {sup 235}U), low-density UAlx research reactor fuel with high-density, low enriched (<20% {sup 235}U) replacements. This search is driven by the attempt to reduce the civil use of high-enriched material because of proliferation risks and terrorist threats. American initiatives, such as the Global Threat Reduction Initiative (GTRI) and the Reduced Enrichment for Research and Test Reactors (RERTR) program have triggered the development of reliable low-enriched fuel types for these reactors, which can replace the high enriched ones without loss of performance. Most success has presently been obtained with U{sub 3}Si{sub 2} dispersion fuel, which is currently used in many research reactors in the world. However, efforts to search for a replacement with even higher density, which will also allow the conversion of some high flux research reactors that currently cannot change to U{sub 3}Si{sub 2} (eg. BR2 in Belgium), have continued and are for the moment mainly directed towards the U(Mo) alloy fuel (7-10 w% Mo). This paper provides an overview of the past efforts and presents the current status of the U(Mo) development. (authors)

From high enriched to low enriched uranium fuel in research reactors

International Nuclear Information System (INIS)

Van Den Berghe, S.; Leenaers, A.; Koonen, E.; Moons, F.; Sannen, L.

2010-01-01

Since the 1970's, global efforts have been going on to replace the high-enriched (>90% 235 U), low-density UAlx research reactor fuel with high-density, low enriched ( 235 U) replacements. This search is driven by the attempt to reduce the civil use of high-enriched material because of proliferation risks and terrorist threats. American initiatives, such as the Global Threat Reduction Initiative (GTRI) and the Reduced Enrichment for Research and Test Reactors (RERTR) program have triggered the development of reliable low-enriched fuel types for these reactors, which can replace the high enriched ones without loss of performance. Most success has presently been obtained with U 3 Si 2 dispersion fuel, which is currently used in many research reactors in the world. However, efforts to search for a replacement with even higher density, which will also allow the conversion of some high flux research reactors that currently cannot change to U 3 Si 2 (eg. BR2 in Belgium), have continued and are for the moment mainly directed towards the U(Mo) alloy fuel (7-10 w% Mo). This paper provides an overview of the past efforts and presents the current status of the U(Mo) development. (authors)

Ma and LLFP transmutation in MTPs and ADSs: the typical SCK.CEN case of transmutations in BR2 and Myrrha. Position with respect to the global needs

International Nuclear Information System (INIS)

Raedt, Ch. de; Verboomen, B.; Aoust, Th.; Malambu, E.; Beeckmans de West-Meerbeeck, A.; Kupschus, P.; Benoit, Ph.; Ait Abderrahim, H.; Baetsle, L.H.

2001-01-01

The proposed paper indicates the performances, in the domain of the transmutation of MAs and LLFPs, of the high flux materials testing reactor BR2 located at SCK-CEN, and compares them with those of the multipurpose ADS MYRRHA, the pre-design of which is at the present time being finalized at SCK-CEN. With thermal neutron fluxes reaching 9.10 14 n/cm 2 s in thermal positions and 4.10 14 n/cm 2 s in the reactor core and, in the latter position, a fast flux (E>0.1 MeV) of 7.10 14 n/cm 2 s, BR2 has a transmutation throughput of the order of 1.5 kg Np+Am per 200 EFPD. This capacity can be used for investigating at the technological scale the transmutation of MAs and LLFPs in a thermal neutron spectrum with a high contribution of epithermal and fast neutrons. The metallurgical behaviour of the targets can hence be studied. In MYRRHA, higher fast fluxes are expected to be attained in irradiation positions near the spallation source, viz fast fluxes (E>0.75 MeV) up to 10. 15 n/cm 2 s. One of the purposes of MYRRHA is therefore its utilisation for the investigation of actinide transmutation feasibility with ADSs. (author)

Facile synthesis of CsPbBr3/PbSe composite clusters

OpenAIRE

Nguyen, Thang Phan; Ozturk, Abdullah; Park, Jongee; Sohn, Woonbae; Lee, Tae Hyung; Jang, Ho Won; Kim, Soo Young

2017-01-01

Abstract In this work, CsPbBr3 and PbSe nanocomposites were synthesized to protect perovskite material from self-enlargement during reaction. UV absorption and photoluminescence (PL) spectra indicate that the addition of Se into CsPbBr3 quantum dots modified the electronic structure of CsPbBr3, increasing the band gap from 2.38 to 2.48 eV as the Cs:Se ratio increased to 1:3. Thus, the emission color of CsPbBr3 perovskite quantum dots was modified from green to blue by increasing the Se ratio ...

Influence of LiBr on photoluminescence properties of porous silicon

Energy Technology Data Exchange (ETDEWEB)

Dimassi, W., E-mail: dimassi_inrst@yahoo.f [Laboratoire de Photovoltaique, Centre de Recherches et des Technologies de l' Energie, Technopole de Borj-Cedria, BP 95 Hammam-Lif 2050 (Tunisia); Haddadi, I.; Bousbih, R.; Slama, S.; Ali Kanzari, M.; Bouaicha, M.; Ezzaouia, H. [Laboratoire de Photovoltaique, Centre de Recherches et des Technologies de l' Energie, Technopole de Borj-Cedria, BP 95 Hammam-Lif 2050 (Tunisia)

2011-05-15

A new method has been developed to improve the photoluminescence intensity of porous silicon (PS), which is first time that LiBr is used for passivation of PS. Immersion of the PS in a LiBr solution, followed by a thermal treatment at 100 {sup o}C for 30 min under nitrogen, leads to a nine fold increase in the intensity of the photoluminescence. The atomic force microscope (AFM) shows an increase of the nanoparticle dimension compared to the initial dimension of the PS nanostructure. The LiBr covers the nanoparticles of silicon without changing the wavelength distribution of the optical excitation and emission spectra. Moreover, a significant decrease of reflectivity was observed for the wavelength in the range of 350-500 nm. - Research highlights: {yields} A new method based on the use of LiBr was developed to enhance nine times the photoluminescence of porous silicon. {yields} The LiBr covers the silicon nanoparticles without changing in the optical excitation and emission spectra. {yields} We observed a significant decrease of the reflectivity in the 350-500 nm spectral range.

Influence of LiBr on photoluminescence properties of porous silicon

International Nuclear Information System (INIS)

Dimassi, W.; Haddadi, I.; Bousbih, R.; Slama, S.; Ali Kanzari, M.; Bouaicha, M.; Ezzaouia, H.

2011-01-01

A new method has been developed to improve the photoluminescence intensity of porous silicon (PS), which is first time that LiBr is used for passivation of PS. Immersion of the PS in a LiBr solution, followed by a thermal treatment at 100 o C for 30 min under nitrogen, leads to a nine fold increase in the intensity of the photoluminescence. The atomic force microscope (AFM) shows an increase of the nanoparticle dimension compared to the initial dimension of the PS nanostructure. The LiBr covers the nanoparticles of silicon without changing the wavelength distribution of the optical excitation and emission spectra. Moreover, a significant decrease of reflectivity was observed for the wavelength in the range of 350-500 nm. - Research highlights: → A new method based on the use of LiBr was developed to enhance nine times the photoluminescence of porous silicon. → The LiBr covers the silicon nanoparticles without changing in the optical excitation and emission spectra. → We observed a significant decrease of the reflectivity in the 350-500 nm spectral range.

XeBr excilamp based on a non-toxic component mixture

Energy Technology Data Exchange (ETDEWEB)

Kelman, V A; Shpenik, Yu O; Zhmenyak, Yu V, E-mail: mironkle@rambler.ru [Institute of Electron Physics, National Academy of Sciences of Ukraine, Universitetska 21, 88017 Uzhgorod (Ukraine)

2011-06-29

This paper presents the results of experimental studies on obtaining UV luminescence of XeBr* molecules at the excitation of a non-toxic Xe-CsBr gas-vapour mixture by a longitudinal pulse-periodic discharge. Effective UV emission yield of the exciplex XeBr* molecules (spectral maximum at 282 nm) is observed within a wide range of excitation conditions. The spectral distribution in the UV emission under the optimal excitation conditions does not differ essentially from that in other XeBr excilamps based on toxic components. The emission of the B {yields} X band of the XeBr* molecules provides the main contribution to the total power of the discharge UV emission. The determined average power of the UV emission for the experimental discharge tube is 12 W at an efficiency of 1%. Spectral, power-related and time-dependent parameters of the laboratory excilamp are presented for a wide range of excitation parameters. A new mechanism of exciplex molecule formation at the excitation of a rare gas/alkali halide vapour mixture is discussed.

XeBr excilamp based on a non-toxic component mixture

International Nuclear Information System (INIS)

Kelman, V A; Shpenik, Yu O; Zhmenyak, Yu V

2011-01-01

This paper presents the results of experimental studies on obtaining UV luminescence of XeBr* molecules at the excitation of a non-toxic Xe-CsBr gas-vapour mixture by a longitudinal pulse-periodic discharge. Effective UV emission yield of the exciplex XeBr* molecules (spectral maximum at 282 nm) is observed within a wide range of excitation conditions. The spectral distribution in the UV emission under the optimal excitation conditions does not differ essentially from that in other XeBr excilamps based on toxic components. The emission of the B → X band of the XeBr* molecules provides the main contribution to the total power of the discharge UV emission. The determined average power of the UV emission for the experimental discharge tube is 12 W at an efficiency of 1%. Spectral, power-related and time-dependent parameters of the laboratory excilamp are presented for a wide range of excitation parameters. A new mechanism of exciplex molecule formation at the excitation of a rare gas/alkali halide vapour mixture is discussed.

Comparison of aggregation behaviors between ionic liquid-type imidazolium gemini surfactant [C12-4-C12im]Br2 and its monomer [C12mim]Br on silicon wafer.

Science.gov (United States)

Ao, Mingqi; Xu, Guiying; Pang, Jinyu; Zhao, Taotao

2009-09-01

The aggregation of ionic liquid-type imidazolium gemini surfactant [C(12)-4-C(12)im]Br(2) on silicon wafer, which is compared with its monomer [C(12)mim]Br, have been studied. AFM morphology images and contact angle measurements suggest that the aggregations of [C(12)-4-C(12)im]Br(2) and [C(12)mim]Br on silicon wafer follow different mechanisms. Below the critical surface aggregation concentrations (CSAC), both surfactant molecules are adsorbed with their hydrophobic tails facing the air. But above the CSAC, [C(12)-4-C(12)im]Br(2) molecules finally form a bilayer structure with hydrophilic head groups facing the air, whereas [C(12)mim]Br molecules form a multilayer structure, and with increasing its concentration, the layer numbers increase with the hydrophobic chains and hydrophilic head groups facing the air by turns. Besides, the watery wettability of [C(12)-4-C(12)im]Br(2)-treated silica surface is lower than that of [C(12)mim]Br at the concentration of 5.0 cmc, and the infrared spectroscopy suggests that the poorer watery wettability of [C(12)-4-C(12)im]Br(2) may be relative to the less-ordered packing of methylene chains inside the aggregate. These different aggregation behaviors for the two surfactants ascribe to the different molecular structures and electrostatic interactions. This work would have certain theoretical guidance meaning on the modification of solid surface.

Effect of NaCl on thermophilic (55°C) methanol degradation in sulfate reducing granular sludge reactors

NARCIS (Netherlands)

Vallero, M.V.G.; Hulshoff Pol, L.W.; Lettinga, G.; Lens, P.N.L.

2003-01-01

The effect of NaCl on thermophilic (55degreesC) methanol conversion in the presence of excess of sulfate (COD/SO42-=0.5) was investigated in two 6.5L lab-scale upflow anaerobic sludge bed reactors inoculated with granular sludge previously not adapted to NaCl<br/>The effect of NaCl on thermophilic

Photodissociation of dibromoethanes at 248 nm: an ignored channel of Br2 elimination.

Science.gov (United States)

Lee, Hsin-Lung; Lee, Ping-Chen; Tsai, Po-Yu; Lin, King-Chuen; Kuo, H H; Chen, P H; Chang, A H H

2009-05-14

Br(2) molecular elimination is probed in the photodissociation of 1,1- and 1,2-C(2)H(4)Br(2) isomeric forms at 248 nm by using cavity ring-down absorption spectroscopy. Their photodissociation processes differ markedly from each other. The quantum yield of the Br(2) fragment in 1,2-dibromoethane is 0.36+/-0.18, in contrast to a value of 0.05+/-0.03 in 1,1-dibromoethane. The vibrational population ratios of Br(2)(v=1)/Br(2)(v=0) are 0.8+/-0.1 and 0.5+/-0.2 for 1,2- and 1,1-dibromoethanes, respectively. The Br(2) yield densities are found to increase by a factor of 35% and 190% for 1,2- and 1,1-dibromoethanes within the same temperature increment. In the ab initio potential energy calculations, the transition state (TS) along the adiabatic ground state surface may correlate to the Br(2) products. The TS energy for 1,2-dibromoethane is well below the excitation energy at 483 kJ/mol, whereas that for 1,1-dibromoethane is slightly above. Such a small TS energy barrier impedes the photodissociation of the ground state 1,1-dibromoethane such that the production yield of Br(2) may become relatively low, but rise rapidly with the temperature. The TS structure shows a larger bond distance of Br-Br in 1,2-dibromoethane than that in 1,1-dibromoethane. That explains why the former isomer may result in hotter vibrational population of the Br(2) fragments.

Kinetics of the Br2-CH3CHO Photochemical Chain Reaction

Science.gov (United States)

Nicovich, J. M.; Shackelford, C. J.; Wine, P. H.

1997-01-01

Time-resolved resonance fluorescence spectroscopy was employed in conjunction with laser flash photolysis of Br2 to study the kinetics of the two elementary steps in the photochemical chain reaction nBr2 + nCH3CHO + hv yields nCH3CBrO + nHBr. In the temperature range 255-400 K, the rate coefficient for the reaction Br((sup 2)P(sub 3/2)) + CH3CHO yields CH3CO + HBr is given by the Arrhenius expression k(sub 6)(T) = (1.51 +/- 0.20) x 10(exp -11) exp(-(364 +/- 41)/T)cu cm/(molecule.s). At 298 K, the reaction CH3CO + Br2 yields CH3CBrO + Br proceeds at a near gas kinetic rate, k(sub 7)(298 K) = (1.08 +/- 0.38) x 10(exp -10)cu cm/(molecule.s).

A Personal Computer-Based Simulator for Nuclear-Heating Reactors

International Nuclear Information System (INIS)

Liu Jie; Zhang Zuoyi; Lu Dongsen; Shi Zhengang; Chen Xiaoming; Dong Yujie

2000-01-01

A personal computer (PC)-based simulator for nuclear-heating reactors (NHRs), PC-NHR, has been developed to provide an educational tool for understanding the design and operational characteristics of an NHR system. A general description of the reactor system as well as the technical basis for the design and operation of the heating reactor is provided. The basic models and equations for the NHR simulation are then given, which include models of the reactor core, the reactor coolant system, the containment, and the control system. The graphical user interface is described in detail to provide a manual for the user to operate the simulator properly. Steady state and several transients have been simulated. The results of PC-NHR are in good agreement with design data and the results of RETRAN-02. The real-time capability is also confirmed

Ductile austenitic steel for fuel cans and core components of sodium cooled reactors; Ein duktiler austenitischer Stahl fuer Huellrohre und Kernkomponenten natriumgekuehlter Brueter

Energy Technology Data Exchange (ETDEWEB)

Schaefer, L.

1995-08-01

Two austenitic steel melts of a new composition have been studied after irradiation in the PFR fast neutron flux, in the BR2 reactor, and in the Harwell V.E. Cyclotron. The investigations were focussed on helium embrittlement and irradiation induced swelling. (orig.)

Update on the direct n-n scattering experiment at the reactor YAGUAR

Science.gov (United States)

Stephenson, S. L.; Crawford, B. E.; Furman, W. I.; Lychagin, E. V.; Muzichka, A. Yu.; Nekhaev, G. V.; Sharapov, E. I.; Shvetsov, V. N.; Strelkov, A. V.; Levakov, B. G.; Lyzhin, A. E.; Chernukhin, Yu. I.; Howell, C. R.; Mitchell, G. E.; Tornow, W.; Showalter-Bucher, R. A.

2013-10-01

The first direct measurement of the 1S0 neutron-neutron scattering experiment using the YAGUAR aperiodic reactor at the Russian Federal Nuclear Center - All Russian Research Institute of Technical Physics has preliminary results. Thermal neutrons are scattered from a thermal neutron ``gas'' within the scattering chamber of the reactor and measured via time-of-flight. These initial results show an unexpectedly large thermal neutron background now understood to be from radiation-induced desorption within the scattering chamber. Analysis of the neutron time-of-flight spectra suggests neutron scattering from H2 and possibly H2O molecules. An experimental value for the desorption yield ηγ of 0.02 molecules/gamma agrees with modeled results. Techniques to reduce the effect of the nonthermal desorption will be presented. This work was supported in part by ISTC project No. 2286, Russia Found. Grant 01-02-17181, the US DOE grants Nos. DE-FG02-97-ER41042 and DE-FG02-97-ER41033, and by the US NSF through Award Nos. 0107263 and 0555652.

Phase formation in systems Re-Se-Br-MBr (M=Li, Na, K, Rb, Cs

International Nuclear Information System (INIS)

Yarovoj, S.S.; Mironov, Yu.V.; Tkachev, S.V.; Fedorov, V.E.

2009-01-01

Phase formation in the systems Re-Se-Br-MBr (M=K, Rb, Cs) has been studied by NMR-spectroscopy and X-ray phase analysis. Polymer complexes Re 6 Se 8 Br 2 and M 2 Re 6 Se 8 Br 4 (M=Cs, Rb), and salts containing cluster anions [Re 6 Se 6 Br 8 ] 2- and [Re 6 Se 7 Br 7 ] 3- are the main products of reactions occurring in molten alkali metal halides in the number of cluster anions [{Re 6 Se 8-n Br n }Br 6 ] (4-n)- (0≤n≤4). Effect of alkali metal cation on the composition and ratios of formed products is established

A comparative study of LaBr{sub 3}(Ce{sup 3+}) and CeBr{sub 3} based gamma-ray spectrometers for planetary remote sensing applications

Energy Technology Data Exchange (ETDEWEB)

Kozyrev, A., E-mail: kozyrev@mx.iki.rssi.ru; Mitrofanov, I.; Bakhtin, B.; Fedosov, F.; Golovin, D.; Litvak, M.; Malakhov, A.; Mokrousov, M.; Nuzhdin, I.; Sanin, A.; Tretyakov, V.; Vostrukhin, A. [Space Research Institute of the Russian Academy of Sciences (IKI), 84/32 Profsoyuznaya St., Moscow 117997 (Russian Federation); Owens, A.; Benkhoff, J. [European Space Agency, ESTEC, Keplerlaan, 2200 AG Noordwijk (Netherlands); Quarati, F. [AP, RST, FAME, Delft University of Technology, Mekelweg 15, 2629 JB Delft (Netherlands); Gonitec BV, J. Bildersstraat 60, 2596 EJ Den Haag (Netherlands); Timoshenko, G.; Shvetsov, V. [Joint Institute for Nuclear Research, Joliot-Curie 6, Dubna, Moscow Region 141980 (Russian Federation); Granja, C.; Slavicek, T.; Pospisil, S. [Institute of Experimental and Applied Physics, Czech Technical University in Prague, Horska 3a/22, 12800 Prague 2 (Czech Republic)

2016-08-15

The recent availability of large volume cerium bromide crystals raises the possibility of substantially improving gamma-ray spectrometer limiting flux sensitivities over current systems based on the lanthanum tri-halides, e.g., lanthanum bromide and lanthanum chloride, especially for remote sensing, low-level counting applications or any type of measurement characterized by poor signal to noise ratios. The Russian Space Research Institute has developed and manufactured a highly sensitive gamma-ray spectrometer for remote sensing observations of the planet Mercury from the Mercury Polar Orbiter (MPO), which forms part of ESA’s BepiColombo mission. The Flight Model (FM) gamma-ray spectrometer is based on a 3-in. single crystal of LaBr{sub 3}(Ce{sup 3+}) produced in a separate crystal development programme specifically for this mission. During the spectrometers development, manufacturing, and qualification phases, large crystals of CeBr{sub 3} became available in a subsequent phase of the same crystal development programme. Consequently, the Flight Spare Model (FSM) gamma-ray spectrometer was retrofitted with a 3-in. CeBr{sub 3} crystal and qualified for space. Except for the crystals, the two systems are essentially identical. In this paper, we report on a comparative assessment of the two systems, in terms of their respective spectral properties, as well as their suitability for use in planetary mission with respect to radiation tolerance and their propensity for activation. We also contrast their performance with a Ge detector representative of that flown on MESSENGER and show that: (a) both LaBr{sub 3}(Ce{sup 3+}) and CeBr{sub 3} provide superior detection systems over HPGe in the context of minimally resourced spacecraft and (b) CeBr{sub 3} is a more attractive system than LaBr{sub 3}(Ce{sup 3+}) in terms of sensitivities at lower gamma fluxes. Based on the tests, the FM has now been replaced by the FSM on the BepiColombo spacecraft. Thus, CeBr{sub 3} now forms

Transcription regulator TRIP-Br2 mediates ER stress-induced brown adipocytes dysfunction.

Science.gov (United States)

Qiang, Guifen; Whang Kong, Hyerim; Gil, Victoria; Liew, Chong Wee

2017-01-09

In contrast to white adipose tissue, brown adipose tissue (BAT) is known to play critical roles for both basal and inducible energy expenditure. Obesity is associated with reduction of BAT function; however, it is not well understood how obesity promotes BAT dysfunction, especially at the molecular level. Here we show that the transcription regulator TRIP-Br2 mediates ER stress-induced inhibition of lipolysis and thermogenesis in BAT. Using in vitro, ex vivo, and in vivo approaches, we demonstrate that obesity-induced inflammation upregulates brown adipocytes TRIP-Br2 expression via the ER stress pathway and amelioration of ER stress in mice completely abolishes high fat diet-induced upregulation of TRIP-Br2 in BAT. We find that increased TRIP-Br2 significantly inhibits brown adipocytes thermogenesis. Finally, we show that ablation of TRIP-Br2 ameliorates ER stress-induced inhibition on lipolysis, fatty acid oxidation, oxidative metabolism, and thermogenesis in brown adipocytes. Taken together, our current study demonstrates a role for TRIP-Br2 in ER stress-induced BAT dysfunction, and inhibiting TRIP-Br2 could be a potential approach for counteracting obesity-induced BAT dysfunction.

Pure Cs4PbBr6: Highly Luminescent Zero-Dimensional Perovskite Solids

KAUST Repository

Saidaminov, Makhsud I.

2016-09-26

So-called zero-dimensional perovskites, such as Cs4PbBr6, promise outstanding emissive properties. However, Cs4PbBr6 is mostly prepared by melting of precursors that usually leads to a coformation of undesired phases. Here, we report a simple low-temperature solution-processed synthesis of pure Cs4PbBr6 with remarkable emission properties. We found that pure Cs4PbBr6 in solid form exhibits a 45% photoluminescence quantum yield (PLQY), in contrast to its three-dimensional counterpart, CsPbBr3, which exhibits more than 2 orders of magnitude lower PLQY. Such a PLQY of Cs4PbBr6 is significantly higher than that of other solid forms of lower-dimensional metal halide perovskite derivatives and perovskite nanocrystals. We attribute this dramatic increase in PL to the high exciton binding energy, which we estimate to be ∼353 meV, likely induced by the unique Bergerhoff–Schmitz–Dumont-type crystal structure of Cs4PbBr6, in which metal-halide-comprised octahedra are spatially confined. Our findings bring this class of perovskite derivatives to the forefront of color-converting and light-emitting applications.

RETRAN-02: a program for transient thermal-hydraulic analysis of complex fluid-flow systems. Volume 4. Applications

International Nuclear Information System (INIS)

Peterson, C.E.; Gose, G.C.; McFadden, J.H.

1983-01-01

RETRAN-02 represents a significant achievement in the development of a versatile and reliable computer program for use in best estimate transient thermal-hydraulic analysis of light water reactor systems. The RETRAN-02 computer program is an extension of the RETRAN-01 program designed to provide analysis capabilities for 1) BWR and PWR transients, 2) small break loss of coolant accidents, 3) balance of plant modeling, and 4) anticipated transients without scram, while maintaining the analysis capabilities of the predecessor code. The RETRAN-02 computer code is constructed in a semimodular and dynamic dimensioned form where additions to the code can be easily carried out as new and improved models are developed. This report (the fourth of a five volume computer code manual) describes the verification and validation of RETRAN-02

Modulation of electronic and optical properties in mixed halide perovskites CsPbCl3xBr3(1-x) and CsPbBr3xI3(1-x)

Science.gov (United States)

Zhou, Ziqi; Cui, Yu; Deng, Hui-Xiong; Huang, Le; Wei, Zhongming; Li, Jingbo

2017-03-01

The recent discovery of lead halide perovskites with band gaps in the visible presents important potential in the design of high efficient solar cells. CsPbCl3, CsPbBr3 and CsPbI3 are stable compounds within this new family of semiconductors. By performing the first-principles calculation, we explore the structural, electronic and optical properties of CsPbCl3xBr3(1-x) and CsPbBr3xI3(1-x) with various compositions of halide atoms. Structural stability is demonstrated with halide atoms distributing randomly at the halide atomic sites. CsPbCl3xBr3(1-x) and CsPbBr3xI3(1-x) exhibit the modulation of their band gaps by varying the halide composition. Our results also indicate that CsPbCl3xBr3(1-x) and CsPbBr3xI3(1-x) with different halide compositions are suitable to application to solar cells for the general features are well preserved. Good absorption to lights of different wavelengths has been obtained in these mixed halide perovskites.