Status of fast reactor activities in the USSR

International Nuclear Information System (INIS)

Troyanov, M.F.; Rinejskij, A.A.

1990-01-01

Four fast reactors are in operation in the USSR now: BR-10, BOR-60, BN-350 and BN-600. Load factor of BN-600 reactor was in 1989 about 76%. On the basis of operational experience of running reactors design of more powerful commercial size BN-800 power reactor has been completed recently and construction work has started at two sites. The BN-1600 reactor is considered to be the prototype of future commercial reactors. In 1990, it was decided to extend its design approach with the aim to find some additional solutions to provide higher safety and better economics. (author). Figs and tabs

IRRADIATION CREEP AND MECHANICAL PROPERTIES OF TWO FERRITIC-MARTENSITIC STEELS IRRADIATED IN THE BN-350 FAST REACTOR

International Nuclear Information System (INIS)

Porollo, S. I.; Konobeev, Yu V.; Dvoriashin, A. M.; Budylkin, N. I.; Mironova, E. G.; Leontyeva-Smirnova, M. V.; Loltukhovsky, A. G.; Bochvar, A. A.; Garner, Francis A.

2002-01-01

Russian ferritic/martensitic steels EP-450 and EP-823 were irradiated to 20-60 dpa in the BN-350 fast reactor in the form of pressurized creep tubes and small rings used for mechanical property tests. Data derived from these steels serves to enhance our understanding of the general behavior of this class of steels. It appears that these steels exhibit behavior that is very consistent with that of Western steels. Swelling is relatively low at high neutron exposure and confined to temperatures less then 420 degrees C, but may be camouflaged somewhat by precipitation-related densification. The irradiation creep studies confirm that the creep compliance of F/M steels is about one-half that of austenitic steels, and that the loss of strength at test temperatures above 500 degrees C is a problem generic to all F/M steels. This conclusion is supported by post-irradiation measurement of short-term mechanical properties. At temperatures below 500 degrees C both steels retain their high strength (yield stress 0.2=550-600 MPa), but at higher test temperatures a sharp decrease of strength properties occurs. However, the irradiated steels still retain high post-irradiation ductility at test temperatures in the range of 20-700 degrees C.

Fast reactors in Russia: State of the art and trends of development

International Nuclear Information System (INIS)

Poplavsky, V.M.; Ashurko, Yu.M.; Zverev, K.V.; Oshkanov, N.N.; Korol'kov, A.S.; Filin, A.I.

2002-01-01

This status report contains the following: facts on nuclear power in Russia from 2001-2002; plans for further development of nuclear power; state of the art on operation of fast reactors in 2002, namely BN-600, experimental reactors BOR-60 and BR-10; construction of NPP BN-800; participation in activities on BN-350 reactor decommissioning; description of trends of design studies in the field of fast reactors and accelerator driven systems

BN-800 as a new stage in development of fast neutron sodium cooled reactors

International Nuclear Information System (INIS)

Poplavskij, V.M.; Chebeskov, A.N.; Matveev, V.I.

2004-01-01

The role of fast reactors in the strategy of evolution of the nuclear power of Russia is discussed, BN-800 under construction, where unique technical and construction decisions are used, is viewed. Economical estimations of expenses with regard for all life cycle demonstrate that fast reactors may be no higher-priced than the most popular in the world water moderated reactors. Closing of nuclear fuel cycle of BN-800 makes possible decision of the problem of plutonium and actinide utilization, that makes the fast reactor more safety for the environment [ru

Criticality safety issues in the disposition of BN-350 spent fuel

International Nuclear Information System (INIS)

Schaefer, R. W.; Klann, R. T.; Koltyshev, S. M.; Krechetov, S.

2000-01-01

A criticality safety analysis has been performed as part of the BN-350 spent fuel disposition project being conducted jointly by the DOE and Kazakhstan. The Kazakhstan regulations are reasonably consistent with those of the DOE. The high enrichment and severe undermoderation of this fast reactor fuel has significant criticality safety consequences. A detailed modeling approach was used that showed some configurations to be safe that otherwise would be rejected. Reasonable requirements for design and operations were needed, and with them, all operations were found to be safe

Irradiation Creep and Swelling of Russian Ferritic-Martensitic Steels Irradiated to Very High Exposures in the BN-350 Fast Reactor at 305-335 degrees C

International Nuclear Information System (INIS)

Konobeev, Yury V.; Dvoriashin, Alexander M.; Porollo, S.I.; Shulepin, S.V.; Budylkin, N.I.; Mironova, Elena G.; Garner, Francis A.

2003-01-01

Russian ferritic/martensitic (F/M) steels EP-450, EP-852 and EP-823 were irradiated in the BN-350 fast reactor in the form of gas-pressurized creep tubes. The first steel is used in Russia for hexagonal wrappers in fast reactors. The other steels were developed for compatibility with Pb-Bi coolants and serve to enhance our understanding of the general behavior of this class of steels. In an earlier paper we published data on irradiation creep of EP-450 and EP-823 at temperatures between 390 and 520C, with dpa levels ranging from 20 to 60 dpa. In the current paper new data on the irradiation creep and swelling of EP-450 and EP-852 at temperatures between 305 and 335C and doses ranging from 61 to 89 dpa are presented. Where comparisons are possible, it appears that these steels exhibit behavior that is very consistent with that of Western steels. Swelling is relatively low at high neutron exposure and confined to temperatures <420C, but may be camouflaged somewhat by precipitation-related densification. These irradiation creep studies confirm that the creep compliance of F/M steels is about one-half that of austenitic steels.

Experience and results of material science research conducted on spent fuel assemblies from the BN-350 fast reactor

Energy Technology Data Exchange (ETDEWEB)

Maksimkin, O.; Gusev, M.; Turubarova, L.G.; Tsai, K.V.; Yarovchuk, A.V. [Institute of Nuclear Physics, Almaty (Kazakhstan)

2007-07-01

Full text of publication follows: The BN-350 fast reactor was commissioned in 1973, ran successfully for many years and is now in the decommission stage. Its unique operational parameters (low temperature of sodium at the input, wide range of damage rates, etc. ) allowed the investigation of a number of new radiation effects on both austenitic and ferritic-martensitic steels. The latter class of steel was extensively employed as wrappers for fuel assemblies. Much of the accumulated experience in BN-350 is relevant to development of fusion devices. Results are presented on post-operational research of steels 12Cr18Ni10Ti, 08Cr16Ni11Mo3, and 12Cr13Mo2BFR, all serving as hexagonal shrouds of fuel assemblies. Structural materials in the active core zone operated at temperatures of 280-430 deg. C, and were irradiated the range of 0.25-83 dpa with damage rates of 10{sup -9} - 10{sup -6} dpa/s). Investigations of irradiated hexagonal shroud materials were performed with using traditional techniques of transmission and scanning electron microscopy, metallography, mechanical tests, hydrostatic weighing, magnetometry, etc. Additionally, new techniques have been developed and employed with great success on these highly irradiated materials, such as optical computer extensometry, and magnetization cartography. Typical results to be covered in this presentation are: a) In 12Cr18Ni10Ti steel irradiated at a low dose rate of 0.12 x 10{sup -8} dpa/s voids were found at 281 deg. C after only 0.65 dpa, demonstrating once again the acceleration of swelling at low dpa rates observed in other steels. b) Data on helium release during annealing of highly irradiated sample are presented. c) Differences in deformation-induced hardening between the shroud's corners and faces leads to post-irradiation differences in swelling and mechanical properties. d) During room temperature mechanical tests of 12Cr18Ni10Ti steel at {approx}56 dpa at 350 deg. C it was found that ductility lost at

Status of fast reactor activities in the Russian Federation

Energy Technology Data Exchange (ETDEWEB)

Troyanov, M F; Rinejsjij, A A [Institute of Physics and Power Engineering, Obninsk (Russian Federation)

1992-07-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication.

Status of fast reactor activities in the Russian Federation

International Nuclear Information System (INIS)

Troyanov, M.F.; Rinejsjij, A.A.

1992-01-01

The power production program was developed before the disintegration of the USSR and CIS. This report covers therefore the current status of power production and consumption in in republics of the former USSR with a separate chapter on the status of nuclear power. It covers some general results concerned with fast reactors operational experience and BN-600 power plant operational experience. This includes radiological conditions at the BN-600 and reactor core operating experience. Separate chapters are devoted to BN-350, BOR-60, BR-10 and BN-800 reactors. Work devoted to large-size reactor design are described including research and development and fabrication

Overview of the fast reactors fuels program

International Nuclear Information System (INIS)

Evans, E.A.; Cox, C.M.; Hayward, B.R.; Rice, L.H.; Yoshikawa, H.H.

1980-04-01

Each nation involved in LMFBR development has its unique energy strategies which consider energy growth projections, uranium resources, capital costs, and plant operational requirements. Common to all of these strategies is a history of fast reactor experience which dates back to the days of the Manhatten Project and includes the CLEMENTINE Reactor, which generated a few watts, LAMPRE, EBR-I, EBR-II, FERMI, SEFOR, FFTF, BR-1, -2, -5, -10, BOR-60, BN-350, BN-600, JOYO, RAPSODIE, Phenix, KNK-II, DFR, and PFR. Fast reactors under design or construction include PEC, CRBR, SuperPhenix, SNR-300, MONJU, and Madras (India). The parallel fuels and materials evolution has fully supported this reactor development. It has involved cermets, molten plutonium alloy, plutonium oxide, uranium metal or alloy, uranium oxide, and mixed uranium-plutonium oxides and carbides

Overview of the fast reactors fuels program. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Evans, E.A.; Cox, C.M.; Hayward, B.R.; Rice, L.H.; Yoshikawa, H.H.

1980-04-01

Each nation involved in LMFBR development has its unique energy strategies which consider energy growth projections, uranium resources, capital costs, and plant operational requirements. Common to all of these strategies is a history of fast reactor experience which dates back to the days of the Manhatten Project and includes the CLEMENTINE Reactor, which generated a few watts, LAMPRE, EBR-I, EBR-II, FERMI, SEFOR, FFTF, BR-1, -2, -5, -10, BOR-60, BN-350, BN-600, JOYO, RAPSODIE, Phenix, KNK-II, DFR, and PFR. Fast reactors under design or construction include PEC, CRBR, SuperPhenix, SNR-300, MONJU, and Madras (India). The parallel fuels and materials evolution has fully supported this reactor development. It has involved cermets, molten plutonium alloy, plutonium oxide, uranium metal or alloy, uranium oxide, and mixed uranium-plutonium oxides and carbides.

Characterizing and packaging BN-350 spent fuel for long-term dry storage

International Nuclear Information System (INIS)

Lambert, J. D. B.; Bolshinsky, I.; Haues, S.L.; Allen, K.J.; Howden, E.A.; Hill, R.N.; Planchon, H.P.; Staples, P.; Karaulov, V.N.; Blynskij, A.P.; Yakovlev, I.K.; Maev, V.; Dumchev, I. A.

2000-01-01

The Republic of Kazakhstan is being assisted by the U.S. Department of Energy in preparing spent fuel from the BN-350 fast reactor for long term dry storage. Argonne National Laboratory was assigned responsibility for the physical and nuclear characterization of the spent fuel, for the design and safety analysis of 6-pac and 4-pac canisters used to contain spent fuel assemblies for storage, and for the design, testing and installation of a closure station at the reactor in which the canisters of fuel are dried, filled with inert gas and welded shut. This paper briefly describes the specialized components and equipment used, the process followed, and experience gained in packaging the spent fuel. Olsen et al and Schaefer separately discuss overall safety and criticality considerations of the packaging process in parallel papers to this conference

BN-1200 Reactor Power Unit Design Development

International Nuclear Information System (INIS)

Vasilyev, B.A.; Shepelev, S.F.; Ashirmetov, M.R.; Poplavsky, V.M.

2013-01-01

Main goals of BN-1200 design: • Develop a reliable new generation reactor plant for the commercial power unit with fast reactor to implement the first-priority objectives in changing over to closed nuclear fuel cycle; • Improve technical and economic indices of BN reactor power unit to the level of those of Russian VVER of equal power; • Enhance the safety up to the level of the requirements for the 4th generation RP

Testing of the dual slab verification detector for attended measurements of the BN-350 dry storage casks

Energy Technology Data Exchange (ETDEWEB)

Santi, Peter A [Los Alamos National Laboratory; Browne, Michael C [Los Alamos National Laboratory; Williams, Richard B [Los Alamos National Laboratory; Parker, Robert F [Los Alamos National Laboratory

2009-01-01

The Dual Slab Verification Detector (DSVD) has been developed and built by Los Alamos National Laboratory in cooperation with the International Atomic Energy Agency (IAEA) as part of the dry storage safeguards system for the spent fuel from the BN-350 fast reactor. The detector consists of two rows of {sup 3}He tubes embedded in a slab of polyethylene which has been designed to be placed on the outer surface of the dry storage cask. The DSVD will be used to perform measurements of the neutron flux emanating from inside the dry storage cask at several locations around each cask to establish a neutron 'fingerprint' that is sensitive to the contents of the cask. The sensitivity of the fingerprinting technique to the removal of specific amount of nuclear material from the cask is determined by the characteristics of the detector that is used to perform the measurements, the characteristics of the spent fuel being measured, and systematic uncertainties that are associated with the dry storage scenario. MCNPX calculations of the BN-350 dry storage asks and layout have shown that the neutron fingerprint verification technique using measurements from the DSVD would be sensitive to both the amount and location of material that is present within an individual cask. To confirm the performance of the neutron fingerprint technique in verifying the presence of BN-350 spent fuel in dry storage, an initial series of measurements have been performed to test the performance and characteristics of the DSVD. Results of these measurements will be presented and compared with MCNPX results.

Irradiation creep and stress-enhanced swelling of Fe-16Cr-15Ni-Nb austenitic stainless steel in BN-350

Energy Technology Data Exchange (ETDEWEB)

Vorobjev, A.N.; Porollo, S.I.; Konobeev, Yu.V. [Institute of Physics and Power Engineering, Obninsk (Russian Federation)] [and others

1997-04-01

Irradiation creep and void swelling will be important damage processes for stainless steels when subjected to fusion neutron irradiation at elevated temperatures. The absence of an irradiation device with fusion-relevant neutron spectra requires that data on these processes be collected in surrogate devices such as fast reactors. This paper presents the response of an annealed austenitic steel when exposed to 60 dpa at 480{degrees}C and to 20 dpa at 520{degrees}C. This material was irradiated as thin-walled argon-pressurized tubes in the BN-350 reactor located in Kazakhstan. These tubes were irradiated at hoop stresses ranging from 0 to 200 MPa. After irradiation both destructive and non-destructive examination was conducted.

Joint European contribution to phase 5 of the BN600 hybrid reactor benchmark core analysis (European ERANOS formulaire for fast reactor core analysis)

International Nuclear Information System (INIS)

Rimpault, G.

2004-01-01

Hybrid UOX/MOX fueled core of the BN-600 reactor was endorsed as an international benchmark. BFS-2 critical facility was designed for full size simulation of core and shielding of large fast reactors (up tp 3000 MWe). Wide experimental programme including measurements of criticality, fission rates, rod worths, and SVRE was established. Four BFS-62 critical assemblies have been designed to study changes in BN-600 reactor physics-when moving to a hybrid MOX core. BFS-62-3A assembly is a full scale model of the BN-600 reactor hybrid core. it consists of three regions of UO 2 fuel, axial and radial fertile blankets, MOX fuel added in a ring between MC and OC zones, 120 deg sector of stainless steel reflector included within radial blanket. Joint European contribution to the Phase 5 benchmark analysis was performed by Serco Assurance Winfrith (UK) and CEA Cadarache (France). Analysis was carried out using Version 1.2 of the ERANOS code; and data system for advanced and fast reactor core applications. Nuclear data is based on the JEF2.2 nuclear data evaluation (including sodium). Results for Phase 5 of the BN-600 benchmark have been determined for criticality and SVRE in both diffusion and transport theory. Full details of the results are presented in a paper posted on the IAEA Business Collaborator website nad a brief summary is provided in this paper

Correlation of yield stress and microhardness in 08Cr16Ni11Mo3 stainless steel irradiated to high dose in the BN-350 fast reactor

International Nuclear Information System (INIS)

Gusev, M.N.; Maksimkin, O.P.; Tivanova, O.V.; Silnaygina, N.S.; Garner, F.A.

2006-01-01

The relationship between the microhardness and the engineering yield stress in 08Cr16Ni11Mo3 steel after irradiation in the BN-350 reactor has been experimentally derived and agrees with a previously published correlation developed by Toloczko for unirradiated 316 in a variety of cold-work conditions. Even more importantly, when the correlation is derived in the K Δ format where the correlation involves changes in the two properties, excellent agreement is found with a universal K Δ correlation developed by Busby and coworkers. Additionally, this report points out that microhardness measurements must take into account that sodium exposure at high temperature and neutron fluence alters the metal surface to produce ferrite, and therefore the altered layers should be removed prior to testing

Assessing reactor physics codes capabilities to simulate fast reactors on the example of the BN-600 benchmark

Energy Technology Data Exchange (ETDEWEB)

Ivanov, Vladimir [Scientific and Engineering Centre for Nuclear and Radiation Safety (SES NRS), Moscow (Russian Federation); Bousquet, Jeremy [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Garching (Germany)

2016-11-15

This work aims to assess the capabilities of reactor physics codes (initially validated for thermal reactors) to simulate fast sodium cooled reactors. The BFS-62-3A critical experiment from the BN-600 Hybrid Core Benchmark Analyses was chosen for the investigation. Monte-Carlo codes (KENO from SCALE and SERPENT 2.1.23) and the deterministic diffusion code DYN3D-MG are applied to calculate the neutronic parameters. It was found that the multiplication factor and reactivity effects calculated by KENO and SERPENT using the ENDF/B-VII.0 continuous energy library are in a good agreement with each other and with the measured benchmark values. Few-groups macroscopic cross sections, required for DYN3D-MG, were prepared in applying different methods implemented in SCALE and SERPENT. The DYN3D-MG results of a simplified benchmark show reasonable agreement with results from Monte-Carlo calculations and measured values. The former results are used to justify DYN3D-MG implementation for sodium cooled fast reactors coupled deterministic analysis.

Study of short-time mechanical properties changes for BN-350 reactor spent fuel assemblies jacket material from vacancy swelling

International Nuclear Information System (INIS)

Karaulov, V.N.; Blynskij, A.P.; Yakovlev, I.L.; Golovin, S.V.; Lambert, D.

1999-01-01

Variations of mechanical properties (ultimate strength and limit of plasticity) for irradiated stainless steels, materials of BN-350 reactor cased fuel assemblies tubes, namely: 12X18H10T MTO, 08X16H11M3 MTO, 10X17H13M2T, 12X13M2BRF from vacancy swelling and neutron damaging doze have been studied. Flat samples cut out from hexagonal fuel assemblies casing were tested. The data on casing profilometry, and also the results from hydrostatic weighing of steel samples, were used to evaluate swelling. All measurements and testing were made at temperature 25 degrees C

Main results of BN-600 reactor stress-strain state investigations

International Nuclear Information System (INIS)

Panov, V.A.

1983-01-01

The development of BN-600 fast reactor plant needed the solution of a series of complex engineering problems including ones for confirming integrity of the most vital structural components. The particular attention was given to the main vessel since reactor availability end safe operation of the plant as a whole depend on vessel strength end integrity. The present report deals with the main results of theoretical and experimental investigations of the stress-strain state of BN-600 reactor vessel carried out during design, start-up and initial bringing the reactor to power

Chemical surveillance of commercial fast breeder reactors

International Nuclear Information System (INIS)

Stamm, H.H.; Stade, K.Ch.

1988-01-01

After BN-600 (USSR) and SUPERPHENIX (France) were started succesfully, the international development of LMFBRs is standing at the doorstep of commercial use. For commercial use of LMFBRs cost reductions for construction and operation are highly desirable and necessary. Several nations developing breeder reactors have joined in a common effort in order to reach this aim by standardization and harmonization. On the base of more than 20 years of operation experience of experimental reactors (EBR-II, FFTF, RAPSODIE, DFR, BR-5/BR-10, BOR-60, JOYO, KNK-II) and demonstration plants (PHENIX, PFR, BN-350), possibilities for standardization in chemical surveillance of commercial breeder reactors without any loss of availability, reliability and reactor safety will be discussed in the following chapters. Loop-type reactors will be considered as well as pool-type reactors, although all commercial plants under consideration so far (SUPERPHENIX II, BN-800, BN-1600, CFBR, SNR-2, EFR) include pool-type reactors only. Table 1 gives a comparison of the Na inventories of test reactors, prototype plants and commercial LMFBRs

Evolution of the technical concept of fast reactors. The concept of BREST

International Nuclear Information System (INIS)

Orlov, V.V.

2001-01-01

Having understood that conventional power was limited by available fuel resources, as well as the environmental concern, and willing to use the advantages of defense nuclear power achievements, the development of civil nuclear power was initiated. Scarce supply of uranium has been a matter of concern from the very beginning of nuclear power development, but plutonium produced in the thermal reactors was supposed to be used as fuel for the fast reactors which would not be limited by fuel resources. In order to attain high breeding ratio and high power density, the first generation of fast reactors were designed with sodium coolant, uranium blanket to make up for a decrease in breeding ratio if uranium oxides were used as fuel. Development of nuclear power in the sixties and seventies was followed by stagnation. Lessons learned from a 50-year experience and new conditions set for power industry demand a new concept of fast reactor which would meet a variety of cost-efficiency and safety requirements in their present understanding. Development of fast breeders in Russia began after commissioning of BN-350 and completion of BN-600 design. According to present demands BREST reactors should be designed so as to implement consistently the principles of natural safety without deviation from materials and technology which was proven in defense and civil nuclear power facilities

Microstructural investigations of fast reactor irradiated austenitic and ferritic-martensitic stainless steel fuel cladding

International Nuclear Information System (INIS)

Agueev, V.S.; Medvedeva, E.A.; Mitrofanova, N.M.; Romanueev, V.V.; Tselishev, A.V.

1992-01-01

Electron microscopy has been used to characterize the microstructural changes induced in advanced fast reactor fuel claddings fabricated from Cr16Ni15Mo3NbB and Cr16Ni15Mo2Mn2TiVB austenitic stainless steels in the cold worked condition and Cr13Mo2NbVB ferritic -martensitic steel following irradiation in the BOR-60, BN-350 and BN-600 fast reactors. The data are compared with the results obtained from a typical austenitic commercial cladding material, Cr16Ni15Mo3Nb, in the cold worked condition. The results reveal a beneficial effect of boron and other alloying elements in reducing void swelling in 16Cr-15Ni type austenitic steels. The high resistance of ferritic-martensitic steels to void swelling has been confirmed in the Cr13Mo2NbVB steel. (author)

Technical meeting on decommissioning of fast reactors after sodium draining. Working material

International Nuclear Information System (INIS)

2005-01-01

The objective of the technical meeting was to provide a forum for in-depth scientific and technical exchange on topics related to the decommissioning experience with fast reactors, in particular with regard to the decommissioning of components after sodium draining. Accordingly, the scope of the meeting covers the review and analyses of the experience gained from the decommissioning of both active sodium loops and sodium cooled fast reactors (e.g., KNK II, Superphenix, RAPSODIE, EBR-II, FERMI, BN-350, BR-10). It is expected that the outcome of the meeting will contribute to the Agency initiative to preserve fast reactor data and knowledge. The main focus of the technical meeting was given on the decommissioning of both active loop and reactor components (e.g., the primary vessel of a sodium-cooled reactor) that have been drained of sodium, but that still conserve some residual amounts of sodium (e.g., films covering the entire surface of the component, or particular sodium heels that cannot be drained)

Validation of BN Reactor Plant Long-Term Operation

International Nuclear Information System (INIS)

Vilensky, O.; Vasilyev, B.; Kaidalov, V.

2013-01-01

The BN RP operation life time is mainly determined by resource of non-replaceable equipment. The new standard (RD) “Procedure of strength analysis for main components of sodium cooled fast neutron reactor plants” was developed to validate structure strength in view of radiation effects and degradation of material properties within the time period up to 300000 hours and under irradiation, as well as development of postulated crack-like defects. Using this RD, the extension of operation life of BN-600 reactor non-replaceable components from 30 to 45 years, as well as strength and durability of the most loaded non-replaceable components of BN-800 RP under construction were validated for the specified 45-year operation life. Wider application of steel 16Cr-11Ni-3Mo refers to new decisions in BN-1200 RP design that allow increasing of operation life of the most loaded non-replaceable components up to 60 years. High-chromium steel 12Cr-Ni-Mo-V-Nb is a new material, which was proposed for SG design to increase the operation life up to 30 years. In addition, the austenitic steels 18Cr-9Ni and 16Cr-11Ni-3Mo are now under upgrading for future application of them in commercial BN-1200 RP. To provide additional long-term reliable and safe operation of BN-1200 RP equipment and pipelines, it is planned to develop and implement the lifetime operational monitoring system

The use of waveguide acoustic probes for void fraction measurement in the evaporator of BN-350-Type reactor

Energy Technology Data Exchange (ETDEWEB)

Melnikov, V.I.; Nigmatulin, B.I.

1995-09-01

The present paper deals with some results of the experimental studies which have been carried out to investigate the steam generation dynamics in the Field tubes of sodium-water evaporators used in the BN-350 reactors. The void fraction measurements have been taken with the aid of waveguide acoustic transducers manufactured in accordance with a specially designed technology (waveguide acoustic transducers-WAT technology). Presented in this paper also the transducer design and calibration methods, as well as the diagram showing transducers arrengment in the evaporator. The transducers under test featured a waveguide of about 4 m in length and a 200-mm long sensitive element (probe). Besides, this paper specifies the void fraction data obtained through measurements in diverse points of the evaporator. The studies revealed that the period of observed fluctuations in the void fraction amounted to few seconds and was largely dependent on the level of water in the evaporator.

Development of physical conceptions of fast reactors

International Nuclear Information System (INIS)

Khomyakov, Yu.S.; Matveev, V.I.; Moiseev, A.V.

2013-01-01

• Russian experience in developing fast reactors has proved clearly scientific justification of conceptual physical principles and their technical feasibility. • However, the potential of fast reactors caused by their physical features has not been fully realized. • In order to assure the real possibility of transition to the nuclear power with fast reactors by about 2030 it is necessary to consistently update fast reactor designs for solving the following key problems: - increasing of self-protection level of reactor core; - improvement of technical and economical characteristics; - solution of the problems related to the fuel supply of nuclear power and assimilation of closed nuclear fuel cycle; - disposal of long lived radioactive waste and transmutation of minor actinides. • Russian program (2010-2020) on the development of basic concepts of the new generation reactors implies successive solution of the above problems. • New technical decisions will be demonstrated by development and assimilation of the new reactors: - BN-800 – development of the fuel cycle infrastructure and mastering of the new types of fuel; - BN-1200 reactor – demonstration economical efficiency of fast reactor and new level of safety; - BREST development and demonstration new heavy liquid metal coolant technology and alternative design concept

Current status of work on preservation of accumulated knowledge on fast reactors in Russia and plan of top-priority measures

International Nuclear Information System (INIS)

Kotchetkov, L.A.; Poplavsky, V.M.; Tsiboulya, A.M.; Ashurko, Yu.M.

2005-01-01

The future of nuclear power is associated with mastering of fast reactor technology. Experience gained in Russia by now in the development of sodium cooled fast reactors (FR) and reactor plants of various applications is one of the most extensive and successful all over the world. Since the late 1940-ies up to now, well-directed, rather intensive work has been carried out in the USSR (later in Russia) on all aspects of fast reactors. Institute for Physics and Power Engineering has been always leading organization in the USSR and in Russia in the area of fast reactors. Work on fast reactors in Russia was carried out by many institutions, namely: IPPE, VNIINM, OKBM, VNIPIET, OKB Gidropress, RIAR, SPbAEP, TsNII Prometey and teams of the BN-350 and the BN-600 plants working in close and fruitful cooperation. Successful operation of the power unit of Beloyarskaya NPP with the BN-600 fast reactor during 25 years is one of the good results of this vast expensive efforts. In view of delay in wide-scale deployment of fast neutron reactors and change of generations of specialists in the area of FR, a necessity has arisen in the preservation of knowledge and experience on FR gained in many countries including Russia. Certain measures in this area have been planned by the Russian organizations. However, the necessity has become imminent in a purposeful systematized approach to the preservation of knowledge in fast reactor area, which can be realized only within the framework of development of appropriate special work program. The basic work trends within the framework of this program have been stated. In view of urgency of some part of this work, it is necessary to prioritize the work contents. IAEA assistance (methodological, organizational and financial) in the implementation of some sections of the program would facilitate successful implementation of the work program on preservation of knowledge on FR in Russia. (author)

New stainless steels of ferrite-martensite grade and perspectives of their application in thermonuclear facilities and fast reactors

International Nuclear Information System (INIS)

Ajtkhozhin, Eh.S.; Maksimkin, O.P.

2007-01-01

Review of scientific literature for last 5 years in which results on study of radiation effect on ferrite-martensite steels - construction materials of fast reactors and most probable candidates for first wall and blanket of the thermonuclear facilities ITER and Demo - are presented. Alongside with this a prior experimental data on study of microstructure changing and physical- mechanical properties of ferrite-martensite steel EhP-450 - the material of hexahedral case of spent assembly of BN-350 fast reactor- are cited. Principal attention was paid to considering of radiation effects of structural components content changing and ferrite-martensite steel swelling irradiated at comparatively low values of radiation damage climb rate

Correlation of Yield Stress And Microhardness in 08cr16ni11mo3 Irradiated To High Dose In The Bn-350 Fast Reactor

International Nuclear Information System (INIS)

Maksimkin, O.P.; Gusev, M.N.; Tivanova, O.S.; Silnaygina, N.S.; Garner, Francis A.

2006-01-01

The relationship between values of the microhardness and the engineering yield stress in steel 08Cr16Ni11Mo3 (Russian analog of AISI 316) heavily irradiated in the BN-350 reactor has been experimentally derived. It agrees very well with the previously published correlation developed by Toloczko for unirradiated 316 in a variety of cold-work conditions. Even more importantly, when the correlation is derived in the K δ format where the correlation involves changes in the two properties, we find excellent agreement with a universal K δ correlation developed by Busby and coworkers. With this K δ correlation, one can predict the value of yield stress in irradiated material based on measured values of microhardness. The technique is particularly suitable when the material of interest is in an inconvenient location or configuration, or when significant gradients in mechanical properties are anticipated over small dimensions. This approach makes it possible to reduce the labor input and risk when conducting such work. It appears that the derived correlation is equally applicable to both Russian and Western austenitic steel, and also in both irradiated and unirradiated conditions. Additionally, this report points out that microhardness measurements must take into account that high temperature sodium exposure alters the metal surface to produce ferrite, and therefore the altered layers should be removed prior to testing

Steam water cycle chemistry of liquid metal cooled innovative nuclear power reactors

International Nuclear Information System (INIS)

Yurmanov, Victor; Lemekhov, Vadim; Smykov, Vladimir

2012-09-01

The Federal Target Program (FTP) of Russian Federation 'Nuclear Energy Technologies of the New Generation for 2010-2015 and for Perspective up to 2020' is aimed at development of advanced nuclear energy technologies on the basis of closed fuel cycle with fast reactors. There are advanced fast reactor technologies of the 4. generation with liquid metal cooled reactors. Development stages of maturity of fast sodium cooled reactor technology in Russia includes experimental reactors BR-5/10 (1958-2002) and BOR-60 (since 1969), nuclear power plants (NPPs) with BN-350 (1972-1999), BN-600 (since 1980), BN-800 (under construction), BN-1200 (under development). Further stage of development of fast sodium cooled reactor technology in Russia is commercialization. Lead-bismuth eutectic fast reactor technology has been proven at industrial scale for nuclear submarines in former Soviet Union. Lead based technology is currently under development and need for experimental justification. Current status and prospects of State Corporation 'Rosatom' participation in GIF activities was clarified at the 31. Meeting of Policy Group of the International Forum 'Generation-IV', Moscow, May 12-13, 2011. In June, 2010, 'Rosatom' joined the Sodium Fast Reactor Arrangement as an authorized representative of the Russian Government. It was also announced the intention of 'Rosatom' to sign the Memorandum on Lead Fast Reactor based on Russia's experience with lead-bismuth and lead cooled fast reactors. In accordance with the above FTP some innovative liquid metal cooled reactors of different design are under development in Russia. Gidropress, well known as WER designer, develops innovative lead-bismuth eutectic cooled reactor SVBR-100. NIKIET develops innovative lead cooled reactor BRESTOD-300. Some other nuclear scientific centres are also involved in this activity, e.g. Research and Development Institute for Power Engineering (RDIPE). Optimum

Method for calculating the forces and deformations in the fast reactor fuel assembly accounting for the effects of reactor control system elements and shutdown

International Nuclear Information System (INIS)

Likhachev, Yu.I.; Vashlyaev, Yu.N.; Kravchenko, I.N.

1980-01-01

Methods for calculating deformations and interaction forces of heat-generating assemblies (HGA) of fast reactor core with account for the effect of control and protection system (CPS) elements at the reactor operation and change of interaction efforts between HGA at the reactor shutdown, are described. The results of testing the suggested methods on example of estimate of HGA behaviour of the BN-350 reactor are presented. For estimating the effect of CPS elements on HGA bending the sector model has been used. It is assumed that HGA deformation inside each sector is independent of HGA deformation of other sectors. A higher calculation accuracy is attained by means of laying out of sectors into regions of preferable influence of emergency protection elements and compensating packets. When determining deformation and interaction efforts between HGA caused by temperature change in the course of shutdown it is supposed that the HGA deformation is purely elastic. The methods described are realized in the form of ABRI-CPS and ABRI-HOL programs written in FORTRAN for the BESM-6 computer. The results of HGA calculations of the BN-350 reactor core show that CPS elements decrease contact efforts in the middle of the central packet, increase contact efforts in the peak of the central packet, increase contact efforts in the peaks of packets from the eight row to the periphery and increase contact efforts in the middles of packets from the 5th to 9th row [ru

Code HEX-Z-DMG for support of accounting for and control of nuclear material software system as part of international safeguards system at BN-350 site

International Nuclear Information System (INIS)

Bushmakin, A.G.; Schaefer, B.

1999-01-01

A code for the computation of the global neutron distribution in the three-dimensional hexagonal-z geometry and multi-group diffusion approximation was developed at BN-350 as the main part of the BN-350 accounting for and control of nuclear material software system. This software system includes: the model for stationary distributions of neutrons; the model to calculate isotope compositions changing; the model of refueling operations; To develop this system next two principal problems were solved: to make a micro cross sections library for all nuclides for the BN-350 reactor core; to develop the code for the computation of the global neutron distribution. To solve first task the twenty-six-energy-groups micro cross sections library for more than seventy nuclides was produced. To solve second task the three-dimensional hexagonal-z geometry and multi-group diffusion approximation code was developed. This code (HEX-Z-DMG) was based on the solution of the multi groups diffusion equation using the standard net approach. The series of calculations was performed in the twenty-six-energy-groups representation using this code. We compared eigenvalues (k eff ), a worth added during refueling operations, spatial and energy-group-dependent neutron flux distributions with results of calculation using other code (DIF3D). After the series of these calculations we can say that the HEX-Z-DMG code is well established to use as the part of the BN-350 accounting for and control of nuclear material software system. (author)

An analysis of main processes at small water-into-sodium leaks in the BN-350 and BN-600 NPP steam generators

International Nuclear Information System (INIS)

Poplavsky, V.M.

1990-01-01

The paper presents the main characteristics of emergency processes at small water-into-sodium leaks that took place during the BN-350 and BN-600 NPP steam generators operation. Leak characteristics are presented, the relationship between such parameters as leak rate and duration, its location in a tube bundle, mass of water ingress into sodium, and the character and size of a failure in the interaction zone is analyzed. (author). 5 refs, 3 figs, 2 tabs

[Radiation ecological environment in the Republic of Kazakhstan in the vicinity of the reactors and on the territory of the Semipalatinsk Test Site].

Science.gov (United States)

Kim, D S

2012-01-01

The results of research into the environmental conditions in the regions of location of the pressurized water reactor WWR-K, fast neutron breeder BN-350 and on the territory of the Semipalatinsk Test Site are represented. The effects of the exposure to aerosol emissions from WWR-K and BN-350 reactors on the environment are summarized. We present some arguments in favor of the safe operation of fission reactors in compliance with the rules and norms of nuclear and radiation protection and the efficient disposal of radioactive waste on the territory of the Republic.

Fast reactor operating experience gained in Russia: Analysis of anomalies and abnormal operation cases

International Nuclear Information System (INIS)

Ashurko, Y.M.; Baklushin, R.P.; Zagorulko, Y.I.; Ivanenko, V.N.; Matveyev, V.P.; Vasilyev, B.A.

2000-01-01

Review of various anomalous events and abnormal operation experience gained in the process of Russian fast reactors operation is given in the paper. The main information refers to the BN-600 demonstration reactor operation. Statistical data on sodium leaks and steam generator failures are presented, and sources of these events and countermeasures taken to avoid their appearance on the operating reactors as well as related changes made in the BN-800 reactor design are considered. In the paper, some features of impurities behaviour are considered in various modes of the BN-600 reactor operation. Information is given on the impurities ingress into the circuits, on abnormal situation emerged in the process of the BN-600 reactor operation and its probable cause. Information is presented on the event related to the increased torque of the BN-600 reactor central rotating column and repair works performed. (author)

Operating experience with Beloyarsk fast reactor BN600 NPP

International Nuclear Information System (INIS)

Saraev, O.M.

2000-01-01

The main results of the seventeen-year operation of the BN600 Nuclear Power Plant are considered. The principal backfittings of the main BN600 Power Plant equipment are presented and summarised. (author)

BN600 reactivity definition

International Nuclear Information System (INIS)

Zheltyshev, V.; Ivanov, A.

2000-01-01

Since 1980, the fast BN600 reactor with sodium coolant has been operated at Beloyarsk Nuclear Power Plant. The periodic monitoring of the reactivity modifications should be implemented in compliance with the standards and regulations applied in nuclear power engineering. The reactivity measurements are carried out in order to confirm the basic neutronic features of a BN600 reactor. The reactivity measurements are aimed to justify that nuclear safety is provided in course of the in-reactor installation of the experimental core components. Two reactivity meters are to be used on BN600 operation: 1. Digital on-line reactivity calculated under stationary reactor operation on power (approximation of the point-wise kinetics is applied). 2. Second reactivity meter used to define the reactor control rod operating components efficiency under reactor startup and take account of the changing efficiency of the sensor, however, this is more time-consumptive than the on-line reactivity meter. The application of two reactivity meters allows for the monitoring of the reactor reactivity under every operating mode. (authors)

Back-to-back technical meetings (TMs): 'TM on the coordinated project (CRP) analyses of and lessons learned from the operational experience with fast reactor equipment and systems' and 'TM to coordinate the Agency's fast reactor knowledge preservation international project in Russia'. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

Since the early 1960's, several countries have undertaken important fast breeder reactor development programs. Fast test reactors were constructed and successfully operated in a number of countries, including Rapsodie (France), KNK-II (Germany), FBTR (India), JOYO (Japan), DFR (UK), BR-10, BOR-60 (Russia), and EBR-II, Fermi, FFTF (USA). This was followed by commercial size prototypes (Phenix, Superphenix (France), SNR-300 (Germany), MONJU (Japan), PFR (UK), BN-350 (Kazakhstan), BN-600 (Russia)], either just under construction, coming on line, or experiencing long term operation. However, from the 1980s onward, and mostly for economical and political reasons, fast reactor development in general began to decline. By 1994, in the USA, the Clinch River Breeder Reactor (CRBR) had been cancelled, and the two fast reactor test facilities, FFTF and EBR-II had been shutdown - EBRII permanently, and FFTF, until recently, in standby condition, but now also facing permanent closure. Thus, in the U.S., effort essentially disappeared for fast breeder reactor development. Similarly, programs in other nations were terminated or substantially reduced. In France, Superphenix was shut down at the end of 1998; SNR-300 in Germany was completed but not taken into operation, and KNK-II was permanently shut down in 1991 (after 17 years of operation) and is scheduled to be dismantled by 2004. In the UK, PFR was shut down in 1994, and in Kazakhstan, BN-350 was shut down in 1998. As the interest and activity in the fast breeder reactor diminished, the retirement of many of the developers and acknowledged experts of this technology reached its peak, between 1990 and 2000. The effort and investment required to replace these skills also diminished in parallel. In addition, the facilities (e.g., hot cells, fuel fabrication and inspection lines, seismic test rigs) required to develop and maintain the fast reactor program are drifting into a degraded state or are being shut down. This leads to the

Water-chemical regime of a fast reactor ower complex

International Nuclear Information System (INIS)

Musikhin, R.N.; Piskunov, E.M.; Samarkin, A.A.; Yurchenko, D.S.

1983-01-01

Some peculiarities of water-chemical regime of a power compleX in Shevchenko are considered. The complex comprises a desalination unit, a gas-masout heating-and-power plant and the BN-350 reactor. The compleX is used for the production of electric and thermal energy and fresh water. The power complex peculiarity is the utilization of disalinated seawater in a technological cycle along with highly mineralized seawater with a total salt content of 13.5 g/l (for cooling) in heat exchanges. A regime of ammoniacal correction of feed water was used as a basic water-chemical regime in the initial period of the BN-350 steam generator operation. Deposits composed mainly of iron oxide slime were observed on steam generator surfaces during the operation under these conditions. A conclusion is made that the regime with chelating agent providing steam generator safe operation without chemical cleaning is the most expedient one

Sodium fires at fast reactors: RF status report

International Nuclear Information System (INIS)

Bagdasarov, Yu.E.; Buksha, Yu.K.; Drobyshev, A.V.; Zybin, V.A.; Ivanenko, V.N.; Kardash, D.Yu.; Kulikov, E.V.; Yagodkin, I.V.

1996-01-01

Scientific and engineering studies carried out in Russian Federation since 1992 up to 1996 in the sodium fire area and their main results are described. A review of activities on modification of the computer codes BOX and AERO developed at IPPE for calculating sodium fire consequences is given. Results of analysis of possible accidental situations at currently designed BN-800 reactor NPP with the use of these codes are presented. Sodium leaks occurring at our domestic fast reactors are briefly analyzed. Experimental work performed are described. Results of comparative analysis of common-cause and sodium fire hazards for fast reactor NPP are presented. (author)

BN-600 power unit 15-year operating experience

International Nuclear Information System (INIS)

Saraev, O.M.; Oshkanov, N.N.; Vylomov, V.V.

1996-01-01

Comprehensive experience has been gained with the operating fast reactor BN-600 with a power out of 600 MWe. This paper includes important performance results and gives also an overview of the experience gained from BN-600 NPP commercial operation during 15 years. (author). 2 figs, 1 tab

Primary Damage Characteristics in Metals Under Irradiation in the Cores of Thermal and Fast Reactors

International Nuclear Information System (INIS)

Pechenkin, V.A.

2012-01-01

For an analysis and forecasting of radiation-induced phenomena in structural materials of WWERs, PWRs and BN reactors the fast neutron fluence is usually used (for structural materials of the reactor cores and internals the fluence of neutrons with energy > 0.1 MeV, for WWER and PWRs vessel steels the fluence of neutrons with energy > 0.5 MeV in Russia and East Europe, and with energy > 1.0 MeV in USA and France). Displacements per atom (dpa) seem to be a more appropriate correlation parameter, because it allows comparing the results of materials irradiation in different neutron energy spectra or with different types of particles (neutrons, ions, fast electrons). Energy spectra of primary knocked atoms (PKA) and 'effective' dpa, which are introduced to take into account the point defect recombination during the relaxation stage of a displacement cascade, can be still better representation of the effect of irradiation on material properties. In this work the results of calculating dose rates (dpa/s, NRT-model), PKA energy spectra and PKA mean energies in metals under irradiation in the cores of Russian reactors WWER-440, WWER-1000 (both power thermal reactors) and BN-600 (power fast reactor) and BR-10 (test fast reactor) are presented. In all the reactors Fe and Zr are considered, with addition of Ti and W in BN-600. 'Effective' dose rates in these metals are calculated. Limitations and uncertainties in the standard dpa formulation (the NRT-dpa) are discussed. IPPE activities in the fields related to the TM subject are considered

Concept of the plant for the BN-800 fast reactor fuel recycling with application of pyro-process and vibro-packing technology

International Nuclear Information System (INIS)

Bychkov, A.V.; Skiba, O.V.; Mayorshin, A.A.; Demidova, L.S.; Kormilitzyna, L.A.; Ishunin, V.S.

2000-01-01

The conception of Plant was developed for MOX-fuel recycle at two BN-800 type fast reactors by pyrochemical reprocessing of irradiated nuclear fuel (INF) and production of vibro-pac fuel pins and SA. INF production process and stages of pyrochemical reprocessing were analyzed. Starting materials were chosen. Characteristics of irradiated SA and requirements for finished products were defined. Volumes of production were estimated. Procedure of waste management was defined. The following description was made: (1) general flow sheet of fuel recycling and partial schemes of single reprocessing; (2) composition of production process equipment; (3) arrangement of production process equipment; (4) lay out of Plant building and engineering communications. Principle economical assessments were made for production under design. (authors)

Safety Design Criteria and Approaches to Safety Substantiation of the BN-1200

International Nuclear Information System (INIS)

Ashurko, I.

2013-01-01

Russian experience in SFR area: Activities on development of safety design criteria for SFRs of the 4th generation is carried out within the GIF framework. Although this reactor technology is considered as innovative that is relevant to the 4th generation, however, it has already a certain history. In this relation, it seems to be useful to analyze the corresponding experience that is available in various countries. 4 SFRs have been successfully operated in the USSR and in the Russian Federation: • Experimental reactor BR-5/10; • Research reactor BOR-60; • Prototype BN-350 power reactor; • Commercial BN-600 power unit at the Beloyarsk NPP. Thus, Russia gained a considerable experience of design, construction and operation of SFRs. In particular, a certain experience has been acquired on safety substantiation of reactors of this type and their licensing. Now BOR-60 and BN-600 continue their operation, BN-800 power unit is under construction, development of the commercial BN-1200 power unit, that is considered as the 4th generation reactor, has been started. Due to limited number of operating SFRs in the world, successful Russian experience in this area should be taken into account for further development and improvement of SFR SDC developed by the GIF Task Force. In particular, participation of SFR designers in this activities would be fruitful and useful

Joint European contribution to phases 1 and 2 of the BN600 hybrid reactor benchmark core analysis

International Nuclear Information System (INIS)

Rimpault, Gerald; Newton, Tim; Smith, Peter

2000-01-01

This paper describes the ERANOS code developed within the European cooperation on fast reactors. Reference scheme and ERANOS code validation are included. The method for BN-600 reactor core analysis and the results of phases 1 and two are presented. They include effective multiplication factors, fuel Doppler constants; steel Doppler constants; sodium density coefficient; steel density coefficients; fuel density coefficient; absorber density coefficient; axial and radial expansion coefficients; dynamic parameters; power distribution; beta and neutron life time; reaction rate distribution

System of Modelling and Calculation Analysis of Neutron- Physical Experiments at Fast Reactors

International Nuclear Information System (INIS)

Moiseyev, A.V.

2008-01-01

There is an actual task on storage, processing and analysis of the unique experimental data received on power fast reactors for their subsequent use in projects of fast reactors of new (4.) generation. For modeling and carrying out analysis of experiments the integrated computing system MODEXSYS has been developed. In this system the mechanism for consecutive calculation of a fast reactor states with the detailed description of its components is created. The system includes the database describing fast reactor states, results of neutron-physical characteristics measurements at fast reactor, calculation and benchmark models of experiments and calculation results. In system convenient search means and the special graphics shell are provided. It has Interfaces for processing of calculation results and their analysis. MODEXSYS system has been applied for analysis of three types of experiments at fast reactor: k eff , control rod worth and energy release distribution. The most important results of this analysis are described. Application of MODEXSYS system will raise accuracy and reliability of forecasting of fast reactors neutron-physical characteristics; for BN-600 reactor recommended level of accuracy is resulted. (authors)

System of Modelling and Calculation Analysis of Neutron- Physical Experiments at Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

Moiseyev, A.V. [SSC RF - IPPE, 1 Bondarenko Square, Obninsk, Kaluga Region 249033 (Russian Federation)

2008-07-01

There is an actual task on storage, processing and analysis of the unique experimental data received on power fast reactors for their subsequent use in projects of fast reactors of new (4.) generation. For modeling and carrying out analysis of experiments the integrated computing system MODEXSYS has been developed. In this system the mechanism for consecutive calculation of a fast reactor states with the detailed description of its components is created. The system includes the database describing fast reactor states, results of neutron-physical characteristics measurements at fast reactor, calculation and benchmark models of experiments and calculation results. In system convenient search means and the special graphics shell are provided. It has Interfaces for processing of calculation results and their analysis. MODEXSYS system has been applied for analysis of three types of experiments at fast reactor: k{sub eff}, control rod worth and energy release distribution. The most important results of this analysis are described. Application of MODEXSYS system will raise accuracy and reliability of forecasting of fast reactors neutron-physical characteristics; for BN-600 reactor recommended level of accuracy is resulted. (authors)

Experience on Russian military origin plutonium conversion into fast reactor nuclear fuel

International Nuclear Information System (INIS)

Grachev, A.F.; Skiba, O.V.; Bychkov, A.V.; Mayorshin, A.A.; Kisly, V.A.; Bobrov, D.A.; Osipenko, A.G.; Babikov, L.G.; Mishinev, V.B.

2001-01-01

According to the Concept of Russian Minatom on military plutonium excess utilization, the State Scientific Center of Russian Federation ''Research Institute of Atomic Reactors'' (Dimitrovgrad) has begun study on possibility of technological processing of the metal military plutonium into MOX fuel. The Program and the stages of its realization are submitted in the paper. During 1998-2000 the first stage of the Program was fulfilled and 50 kg of military origin metallic plutonium was converted to MOX fuel for the BOR-60 and BN-600 reactor. The plutonium conversion into MOX fuel is carried out under the original technology developed by SSC RIAR. It includes pyro-electrochemical process for production of fuel on the domestic equipment with the subsequent fuel pins manufacturing for the fast reactors by the vibro-packing method. The produced MOX fuel is purified from alloy additives (Ga) and corresponds to the vibro-packed fuel standard for fast reactors. The fuel pins manufacturing for BOR-60 and BN-600 reactors are carried out by the vibro-packing method on a standard procedure, which is used in SSC RIAR more than 20 years. (author)

Fast reactor database. 2006 update

International Nuclear Information System (INIS)

2006-12-01

plants. The recurring themes are the selection and summary of the data associated with the choice of coolant, fuel and structural materials, reduction of the steel weight, simplification of the plant design/layout, other important fast reactor design issues, and how to solve these problems. In the field of fast reactor design and operational data, the last reference document published by the IAEA was the 1996 Fast Reactor Database (IAEA-TECDOC-866). Since its publication, quite a lot has happened: the construction of two new reactors has been launched, and conceptual/design studies were initiated for various fast reactors, e.g. the Japanese JSFR-1500 and the Russian BN-1800 (both cooled by sodium), as well as for a wholly new line of LMFR concepts - modular reactors cooled by sodium and by lead-bismuth alloy, and prototype and demonstration commercial size fast reactors cooled by lead. The data were produced by the IAEA's Technical Working Group on Fast Reactors (TWG-FR). For many of the TWG-FR Member States there is a significant history of fast reactor development, often extending over a period of 40+ years. The new and updated information on LMFR, which are in operation, under construction or development, has been prepared with contributions from China, India, Japan, Republic of Korea and the Russian Federation. The information contained in IAEA-TECDOC-866, produced by France, Germany, Italy, the UK and the USA, was included in the present report with some modification taking into account last events

Turning into carbonate the residual sodium left in BN-350 circuits may alleviate concerns over their long term safe confinement

International Nuclear Information System (INIS)

Rahmani, L

2000-01-01

After the coolant is drained from the reactor vessel and from the primary and secondary circuits of the BN-350 nuclear power plant, what sodium is left in ponds and films may amount to hundreds of kilograms. For the long term safe storage period which is to follow, preliminary safety analyses (e.g. derived from those made for French sodium cooled reactors) might show that the risks incurred through loss of leaktightness are significant. The ingress of moisture into the circuits would generate, by reaction with the sodium, two undesirable products : sodium hydroxide and hydrogene. Even when considering that water would enter the circuits progressively, so that the heat of the reaction does not give rise to over-pressure, some main risk factors remain. The most promising solution to this challenge appears to be the carbonation of the sodium residues, by progressive diffusion of an appropriate association of carbon dioxyde and water vapour through the inert gaseous medium which fills the circuits. The desired product is porous sodium hydrogenocarbonate

Thermal stratification of sodium in the BN 600 reactor

International Nuclear Information System (INIS)

Obmelukhin, J.A.; Obukhov, P.I.; Rinejskij, A.A.; Sobolev, V.A.; Sherbakov, S.I.

1983-01-01

The signs of thermal stratification of sodium in the BN 600 reactor upper plenum revealed by the analysis of standard temperature sensors' readings are defined. The initial conditions for existence of different temperature sodium layers are given. Two approaches for realizing on a computer of equations describing sodium motion in the upper plenum of the reactor are presented. (author)

Organization and processes of the BN-600 reactor mounting

International Nuclear Information System (INIS)

Dubrovin, E.Z.; Karpenko, V.N.; Takhtaulov, V.M.

1982-01-01

Structural peculiarities of the BN-600 reactor plant are considered. Experience of metal structure mounting inside the reactor vessel has been analysed. Recommendations on the improvements on the organization of the thermal mechanical equipment mounting are given. It is concluded that the consideration of these recommendations will permit to reduce expenditures of labour by 10-40% for the mounting

Neutron-physical simulation of fast nuclear reactor cores. Investigation of new and emerging nuclear reactor systems

International Nuclear Information System (INIS)

Friess, Friederike Renate

2017-01-01

According to a many publications and discussions, fast reactors hold promises to improve safety, non-proliferation, economic aspects, and reduce the nuclear waste problems. Consequently, several reactor designs advocated by the Generation IV Forum are fast reactors. In reality, however, after decades of research and development and billions of dollars investment worldwide, there are only two fast breeders currently operational on a commercial basis: the Russian reactors BN-600 and BN-800. Energy generation alone is apparently not a sufficient selling point for fast breeder reactors. Therefore, other possible applications for fast nuclear reactors are advocated. Three relevant examples are investigated in this thesis. The first one is the disposition of excess weapon-grade plutonium. Unlike for high enriched uranium that can be downblended for use in light water reactors, there exists no scientifically accepted solution for the disposition of weapon-grade plutonium. One option is the use in fast reactors that are operated for energy production. In the course of burn-up, the plutonium is irradiated which intends to fulfill two objectives: the resulting isotopic composition of the plutonium is less suitable for nuclear weapons, while at the same time the build-up of fission products results in a radiation barrier. Appropriate reprocessing technology is in order to extract the plutonium from the spent fuel. The second application is the use as so-called nuclear batteries, a special type of small modular reactors (SMRs). Nuclear batteries offer very long core lifetimes and have a very small energy output of sometimes only 10 MWe. They can supposedly be placed (almost) everywhere and supply energy without the need for refueling or shuffling of fuel elements for long periods. Since their cores remain sealed for several decades, nuclear batteries are claimed to have a higher proliferation resistance. The small output and the reduced maintenance and operating requirements

Neutron-physical simulation of fast nuclear reactor cores. Investigation of new and emerging nuclear reactor systems

Energy Technology Data Exchange (ETDEWEB)

Friess, Friederike Renate

2017-07-12

According to a many publications and discussions, fast reactors hold promises to improve safety, non-proliferation, economic aspects, and reduce the nuclear waste problems. Consequently, several reactor designs advocated by the Generation IV Forum are fast reactors. In reality, however, after decades of research and development and billions of dollars investment worldwide, there are only two fast breeders currently operational on a commercial basis: the Russian reactors BN-600 and BN-800. Energy generation alone is apparently not a sufficient selling point for fast breeder reactors. Therefore, other possible applications for fast nuclear reactors are advocated. Three relevant examples are investigated in this thesis. The first one is the disposition of excess weapon-grade plutonium. Unlike for high enriched uranium that can be downblended for use in light water reactors, there exists no scientifically accepted solution for the disposition of weapon-grade plutonium. One option is the use in fast reactors that are operated for energy production. In the course of burn-up, the plutonium is irradiated which intends to fulfill two objectives: the resulting isotopic composition of the plutonium is less suitable for nuclear weapons, while at the same time the build-up of fission products results in a radiation barrier. Appropriate reprocessing technology is in order to extract the plutonium from the spent fuel. The second application is the use as so-called nuclear batteries, a special type of small modular reactors (SMRs). Nuclear batteries offer very long core lifetimes and have a very small energy output of sometimes only 10 MWe. They can supposedly be placed (almost) everywhere and supply energy without the need for refueling or shuffling of fuel elements for long periods. Since their cores remain sealed for several decades, nuclear batteries are claimed to have a higher proliferation resistance. The small output and the reduced maintenance and operating requirements

Assessment of the dry process fuel sodium-cooled fast reactors

Energy Technology Data Exchange (ETDEWEB)

Roh, Gyu Hong; Choi, Hang Bok

2004-04-01

The feasibility of using dry-processed oxide fuel in a Sodium-cooled Fast Reactor (SFR) was analyzed for the equilibrium fuel cycle of two reference cores: Hybrid BN-600 benchmark core with a enlarged lattice pitch and modified BN-600 core. The dry process technology assumed in this study based on the molten-salt process, which was developed by Russian scientists for recycling oxide fuels. The core calculation was performed by the REBUS-3 code and the reactor characteristics such as the transuranic enrichment, breeding ratio, peak linear power, burnup reactivity swing, etc. were calculated for the equilibrium core under a fixed fuel management scheme. The results showed that a self-sustainable breakeven core was achievable without blanket fuels when the fuel volume fraction was {approx}50% and most of the fission products were removed.

Assessment of the dry process fuel sodium-cooled fast reactors

International Nuclear Information System (INIS)

Roh, Gyu Hong; Choi, Hang Bok

2004-04-01

The feasibility of using dry-processed oxide fuel in a Sodium-cooled Fast Reactor (SFR) was analyzed for the equilibrium fuel cycle of two reference cores: Hybrid BN-600 benchmark core with a enlarged lattice pitch and modified BN-600 core. The dry process technology assumed in this study based on the molten-salt process, which was developed by Russian scientists for recycling oxide fuels. The core calculation was performed by the REBUS-3 code and the reactor characteristics such as the transuranic enrichment, breeding ratio, peak linear power, burnup reactivity swing, etc. were calculated for the equilibrium core under a fixed fuel management scheme. The results showed that a self-sustainable breakeven core was achievable without blanket fuels when the fuel volume fraction was ∼50% and most of the fission products were removed

Characteristics of fast reactor core designs and closed fuel cycle

International Nuclear Information System (INIS)

Poplavsky, V.M.; Eliseev, V.A.; Matveev, V.I.; Khomyakov, Y.S.; Tsyboulya, A.M.; Tsykunov, A.G.; Chebeskov, A.N.

2007-01-01

On the basis of the results of recent studies, preliminary basic requirements related to characteristics of fast reactor core and nuclear fuel cycle were elaborated. Decreasing reactivity margin due to approaching breeding ratio to 1, requirements to support non-proliferation of nuclear weapons, and requirements to decrease amount of radioactive waste are under consideration. Several designs of the BN-800 reactor core have been studied. In the case of MOX fuel it is possible to reach a breeding ratio about 1 due to the use of larger size of fuel elements with higher fuel density. Keeping low axial fertile blanket that would be reprocessed altogether with the core, it is possible to set up closed fuel cycle with the use of own produced plutonium only. Conceptual core designs of advanced commercial reactor BN-1800 with MOX and nitride fuel are also under consideration. It has been shown that it is expedient to use single enrichment fuel core design in this reactor in order to reach sufficient flattening and stability of power rating in the core. The main feature of fast reactor fuel cycle is a possibility to utilize plutonium and minor actinides which are the main contributors to the long-living radiotoxicity in irradiated nuclear fuel. The results of comparative analytical studies on the risk of plutonium proliferation in case of open and closed fuel cycle of nuclear power are also presented in the paper. (authors)

TEMP-M program for thermal-hydraulic calculation of fast reactor fuel assemblies

International Nuclear Information System (INIS)

Bogoslovskaya, C.P.; Sorokin, A.P.; Tikhomirov, B.B.; Titov, P.A.; Ushakov, P.A.

1983-01-01

TEMP-M program (Fortran, BESM-6 computer) for thermal-hydraulic calculation of fast reactor fuel assemblies is described. Results of calculation of temperature field in a 127 fuel element assembly of BN-600, reactor accomplished according to TEMP-N program are considered as an example. Algorithm, realized in the program, enables to calculate the distributions of coolant heating, fuel element temperature (over perimeter and length) and assembly shell temperature. The distribution of coolant heating in assembly channels is determined from a solution of the balance equation system which accounts for interchannel exchange, nonadiabatic conditions on the assembly shell. The TEMP-M program gives necessary information for calculation of strength, seviceability of fast reactor core elements, serves an effective instrument for calculations when projecting reactor cores and analyzing thermal-hydraulic characteristics of operating reactor fuel assemblies

Core concept of fast power reactor with zero sodium void reactivity

International Nuclear Information System (INIS)

Matveev, V.I.; Chebeskov, A.N.; Krivitsky, I.Y.

1991-01-01

The paper presents a core concept of BN-800 - type fast power reactor with zero sodium void reactivity (SVR). Consideration is given to the layout-and some design features of such a core. Some considerations on the determination of the required SVR value as one of the fast reactor safety criteria in accidents with coolant boiling are presented. Some methodical considerations an the development of calculation models that give a correct description of the new core features are stated. The results of the integral SVR calculation studies are included. reactivity excursions under different scenarios of sodium boiling are estimated, some corrections into the calculated SVR value are discussed. (author)

Monte Carlo Modeling Electronuclear Processes in Cascade Subcritical Reactor

CERN Document Server

Bznuni, S A; Zhamkochyan, V M; Polyanskii, A A; Sosnin, A N; Khudaverdian, A G

2000-01-01

Accelerator driven subcritical cascade reactor composed of the main thermal neutron reactor constructed analogous to the core of the VVER-1000 reactor and a booster-reactor, which is constructed similar to the core of the BN-350 fast breeder reactor, is taken as a model example. It is shown by means of Monte Carlo calculations that such system is a safe energy source (k_{eff}=0.94-0.98) and it is capable of transmuting produced radioactive wastes (neutron flux density in the thermal zone is PHI^{max} (r,z)=10^{14} n/(cm^{-2} s^{-1}), neutron flux in the fast zone is respectively equal PHI^{max} (r,z)=2.25 cdot 10^{15} n/(cm^{-2} s^{-1}) if the beam current of the proton accelerator is k_{eff}=0.98 and I=5.3 mA). Suggested configuration of the "cascade" reactor system essentially reduces the requirements on the proton accelerator current.

Concept and designs of new-generation fast reactors

International Nuclear Information System (INIS)

Mitenkov, F.M.

1993-01-01

This article discusses the general safety requirements and characteristics for future nuclear power plants. It examines various designs - loop, block, and integrated layouts for reactors. Specifically, the article focuses an integrated design for sodium-cooled fast reactors noting that the BN-600 reactor has operated accident-free over the past 12 years. An obvious advantage of this scheme is that the coolant of the primary loop is localized in one volume (in a vessel), there are no short connections and large-diameter pipes, which of course sharply reduces the probability in coolant leaks. With an integrated scheme the problem of embrittlement of the reactor vessel by neutron irradiation is obviated. The neutron fluence for the vessels of the AST-500 and VPBER-600 reactors, built with an integrated scheme, is less than 10 17 cm -2 . Such a fluence does not cause any appreciable change in the mechanical properties of the vessel steel. The integrated layout of the reactor makes it possible to build a containment vessel. In this case it is possible to eliminate the danger of the reactor core drying out and thus cooling of the reactor in emergency situations can be simplified substantially. In an integrated layout, however, access is more difficult to the equipment inside the reactor, thus limiting or complicating maintenance work. The integrated layout, therefore, requires the use of highly reliable equipment built according to designs that have been proven in operation and have been passed representative service-life tests under laboratory conditions. The integrated layout considerably increases the mass and size characteristics of the reactor. New solutions thus are needed for the organization of work on reactor fabrication and assembly. In the case of the BN-600 and Superphenix reactors the welding of the reactor vessels and the assembly work were done on the building site

Characterization and management of radioactive sodium and other reactor components as input data for the decommissioning of liquid metal-cooled fast reactors. A compilation of data produced of data produced by members of the IAEA technical working group on fast reactors (TWG-FR) at two consultancies and one technical committee meeting. Working material

International Nuclear Information System (INIS)

2002-01-01

A number of liquid metal cooled fast reactors (LMFRs) are in operation and, some have already been shut down; other reactors will reach the end of their design lifetime in a few years and become candidates for decommissioning. It is unfortunate that little consideration was devoted to decommissioning of reactors at the plant design and construction stage. It is with this focus that the Technical Working Group on Fast Reactors (TWGFR) recommended that the IAEA organize the exchange of information on LMFRs decommissioning technology. It was pointed out that the decommissioning of small sodium-cooled reactors has shown that there are two basic differences between thermal and fast reactors decommissioning: on the one side, the treatment and disposal of radioactive sodium coolant, and on the other side, the management of reactor components, for which the structural materials are activated in depth by fast neutrons. To this end, a Technical Committee Meeting on Sodium Removal and Disposal from LMFRs in Normal Operation and in the framework of Decommissioning (Aix-en-Provence, France, November 1997) and two Consultancies on Decommissioning of the Kazakh BN-350 LMFR (Vienna, Austria, October 1996; Obninsk, Russian Federation, February 1998) were convened by the IAEA. These Meetings brought together a group of experts from France, Russia, Kazakhstan, the UK, and the USA to exchange information on, and to review current technical knowledge and experience in the management of radioactive coolant and reactor components following closing of LMFRs, as well as their design features and operating experience relevant for decommissioning procedures. The report provides general and detailed information on activation characteristics of the primary coolant; treatment and disposal of the spent sodium; removal of the residual sodium deposits and decontamination; the activation characteristics of the reactor components and the management of the latter. The recurring theme is finding

Monte-Carlo modeling of parameters of a subcritical cascade reactor based on MSBR and LMFBR technologies

International Nuclear Information System (INIS)

Bznuni, S.A.; Zhamkochyan, V.M.; Khudaverdyan, A.G.; Barashenkov, V.S.; Sosnin, A.N.; Polanski, A.

2001-01-01

Parameters are investigated of a subcritical cascade reactor driven by a proton accelerator and based on a primary lead-bismuth target, main reactor constructed analogously to the molten salt breeder (MSBR) reactor core and a booster-reactor analogous to the core of the BN-350 liquid metal cooled fast breeder reactor (LMFBR). It is shown by means of Monte-Carlo modeling that the reactor under study provides safe operation modes (k eff = 0.94 - 0.98), is capable to transmute effectively radioactive nuclear waste and reduces by an order of magnitude the requirements on the accelerator beam current. Calculations show that the maximal neutron flux in the thermal zone is 10 14 cm 12 · s -1 , in the fast booster zone is 5.12 · 10 15 cm 12 · s -1 at k eff = 0.98 and proton beam current I = 2.1 mA. (author)

Monte-Carlo Modeling of Parameters of a Subcritical Cascade Reactor Based on MSBR and LMFBR Technologies

CERN Document Server

Bznuni, S A; Zhamkochyan, V M; Polanski, A; Sosnin, A N; Khudaverdyan, A H

2001-01-01

Parameters of a subcritical cascade reactor driven by a proton accelerator and based on a primary lead-bismuth target, main reactor constructed analogously to the molten salt breeder (MSBR) reactor core and a booster-reactor analogous to the core of the BN-350 liquid metal cooled fast breeder reactor (LMFBR). It is shown by means of Monte-Carlo modeling that the reactor under study provides safe operation modes (k_{eff}=0.94-0.98), is apable to transmute effectively radioactive nuclear waste and reduces by an order of magnitude the requirements on the accelerator beam current. Calculations show that the maximal neutron flux in the thermal zone is 10^{14} cm^{12}\\cdot s^_{-1}, in the fast booster zone is 5.12\\cdot10^{15} cm^{12}\\cdot s{-1} at k_{eff}=0.98 and proton beam current I=2.1 mA.

Design considerations for economically competitive sodium cooled fast reactors

International Nuclear Information System (INIS)

Zhang, Hongbin; Zhao, Haihua; Mousseau, Vincent; Szilard, Ronaldo

2009-01-01

The technological viability of sodium cooled fast reactors (SFR) has been established by various experimental and prototype (demonstration) reactors such as EBR-II, FFTF, Phenix, JOYO, BN-600 etc. However, the economic competitiveness of SFR has not been proven yet. The perceived high cost premium of SFRs over LWRs has been the primary impediment to the commercial expansion of SFR technologies. In this paper, cost reduction options are discussed for advanced SFR designs. These include a hybrid loop-pool design to optimize the primary system, multiple reheat and intercooling helium Brayton cycle for the power conversion system and the potential for suppression of intermediate heat transport system. The design options for the fully passive decay heat removal systems are also thoroughly examined. These include direct reactor auxiliary cooling system (DRACS), reactor vessel auxiliary cooling system (RVACS) and the newly proposed pool reactor auxiliary cooling system (PRACS) in the context of the hybrid loop-pool design. (author)

The concerted calculation of the BN-600 reactor for the deterministic and stochastic codes

Science.gov (United States)

Bogdanova, E. V.; Kuznetsov, A. N.

2017-01-01

The solution of the problem of increasing the safety of nuclear power plants implies the existence of complete and reliable information about the processes occurring in the core of a working reactor. Nowadays the Monte-Carlo method is the most general-purpose method used to calculate the neutron-physical characteristic of the reactor. But it is characterized by large time of calculation. Therefore, it may be useful to carry out coupled calculations with stochastic and deterministic codes. This article presents the results of research for possibility of combining stochastic and deterministic algorithms in calculation the reactor BN-600. This is only one part of the work, which was carried out in the framework of the graduation project at the NRC “Kurchatov Institute” in cooperation with S. S. Gorodkov and M. A. Kalugin. It is considering the 2-D layer of the BN-600 reactor core from the international benchmark test, published in the report IAEA-TECDOC-1623. Calculations of the reactor were performed with MCU code and then with a standard operative diffusion algorithm with constants taken from the Monte - Carlo computation. Macro cross-section, diffusion coefficients, the effective multiplication factor and the distribution of neutron flux and power were obtained in 15 energy groups. The reasonable agreement between stochastic and deterministic calculations of the BN-600 is observed.

3-D thermal hydraulic analysis of transient heat removal from fast reactor core using immersion coolers

International Nuclear Information System (INIS)

Chvetsov, I.; Volkov, A.

2000-01-01

For advanced fast reactors (EFR, BN-600M, BN-1600, CEFR) the special complementary loop is envisaged in order to ensure the decay heat removal from the core in the case of LOF accidents. This complementary loop includes immersion coolers that are located in the hot reactor plenum. To analyze the transient process in the reactor when immersion coolers come into operation one needs to involve 3-D thermal hydraulics code. Furthermore sometimes the problem becomes more complicated due to necessity of simulation of the thermal hydraulics processes into the core interwrapper space. For example on BN-600M and CEFR reactors it is supposed to ensure the effective removal of decay heat from core subassemblies by specially arranged internal circulation circuit: 'inter-wrapper space'. For thermal hydraulics analysis of the transients in the core and in the whole reactor including hot plenum with immersion coolers and considering heat and mass exchange between the main sodium flow and sodium that moves in the inter-wrapper space the code GRIFIC (the version of GRIF code family) was developed in IPPE. GRIFIC code was tested on experimental data obtained on RAMONA rig under conditions simulating decay heat removal of a reactor with the use of immersion coolers. Comparison has been made of calculated and experimental result, such as integral characteristics (flow rate through the core and water temperature at the core inlet and outlet) and the local temperatures (at thermocouple location) as well. In order to show the capabilities of the code some results of the transient analysis of heat removal from the core of BN-600M - type reactor under loss-of-flow accident are presented. (author)

Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part III

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-11-01

The Summary Report - Part III of the Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercial development of FBRs according to national plans, mostly related to technology problems of containment design, fuel fabrication, fuel failures, sodium pressure, fuel-sodium interaction, computer codes needed for licensing. Most of the discussions were related to the existing reactors: BN-600, BN-350, BN-1600, BOR-60, RAPSODIE, PHENIX.

Tenth annual meeting, Vienna, Austria, 29 March - 1 April 1977. Summary report. Part III

International Nuclear Information System (INIS)

1977-11-01

The Summary Report - Part III of the Tenth Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercial development of FBRs according to national plans, mostly related to technology problems of containment design, fuel fabrication, fuel failures, sodium pressure, fuel-sodium interaction, computer codes needed for licensing. Most of the discussions were related to the existing reactors: BN-600, BN-350, BN-1600, BOR-60, RAPSODIE, PHENIX

Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part III

International Nuclear Information System (INIS)

1978-09-01

The Summary Report - Part III of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercialization LMFBRs according to national plans, mostly related to technology of fuel fabrication, PHENIX fuel pins testing, heterogeneous cores, in service inspection of fuel elements, regulations and licensing, and related OECD activities. Most of the discussions were related to the existing reactors: BR-10, BN-600, BN-350, BN-1600, RAPSODIE and PHENIX

Eleventh annual meeting, Bologna, Italy, 17-20 April 1978. Summary report. Part III

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-09-01

The Summary Report - Part III of the Eleventh Annual Meeting of the IAEA International Working Group on Fast Reactors - contains the discussions on the commercialization LMFBRs according to national plans, mostly related to technology of fuel fabrication, PHENIX fuel pins testing, heterogeneous cores, in service inspection of fuel elements, regulations and licensing, and related OECD activities. Most of the discussions were related to the existing reactors: BR-10, BN-600, BN-350, BN-1600, RAPSODIE and PHENIX.

The fast reactor

International Nuclear Information System (INIS)

1980-02-01

The subject is discussed as follows: brief description of fast reactors; advantage in conserving uranium resources; experience, in UK and elsewhere, in fast reactor design, construction and operation; safety; production of plutonium, security aspects; consideration of future UK fast reactor programme. (U.K.)

Unusual occurrences during the whole operation of BN-250 NPP

International Nuclear Information System (INIS)

Andropenkov, S.

2000-01-01

Unusual occurrences during the whole operation BN-350 NPP. 1. Oil ingress in high pressure receiver for the not reveled reason, 12.05.1994. 2. lncrease of water radioactivity of circulating water supply system due to heat exchanger leak of spent fuel assembly washing out system, 17.09.1993. 3. Lack of passableness of sodium drain header of primary circuit reveled during inspection on scheduled preventative maintenance, 28.11.1996. 4. Destruction of the blow-off line of MCP-6 due to corrosion damage of the pipeline while unit was being operated at rated power, 23.04.1993. 5. Lack of passableness of blow-down pipeline connecting reactor gas cover with gas-type pressurizer while unit was being operated at rated power, 17.11.1994. 6. Sodium ingress in blow-down pipeline of loop-5 intermediate heat exchanger while loop-5 was being fed of sodium during scheduled preventative maintenance, 27.06.1994. 7. Resistance deterioration of electro heating zones of loop-4 due to heat exchanger leak and water ingress in air-pipeline of primary circuit boxes recirculating air system, 02.05.1997. 8. Resistance deterioration of electro heating zones of sodium drain header of secondary circuit was sopped in the water for the extinguishing the fire of blowing ventilation oil-strainer, 23.12.1994. 9. Sodium ingress in gas-type pressurizer through pipeline of primary sodium cleanup system and blow-down pipeline of failed MCP-2 while primary sodium cleanup system was being connected to the primary circuit, 17.08.1976. As a rule, the main reactor systems are scrutinized more carefully than the auxiliary reactor systems and the order actions are existed for eliminating and mitigating of consequences of main reactor system fails. Therefore the auxiliary reactor system fails may impact on the main reactor systems through places of its contact in significant measure. The influence of auxiliary reactor system fails on main reactor systems and its possible consequences for behavior of the main

Fast breeder reactors

International Nuclear Information System (INIS)

Heinzel, V.

1975-01-01

The author gives a survey of 'fast breeder reactors'. In detail the process of breeding, the reasons for the development of fast breeders, the possible breeder reactors, the design criteria, fuels, cladding, coolant, and safety aspects are reported on. Design data of some experimental reactors already in operation are summarized in stabular form. 300 MWe Prototype-Reactors SNR-300 and PFR are explained in detail and data of KWU helium-cooled fast breeder reactors are given. (HR) [de

A conceptual design of neutron tumor therapy reactor facility with a YAYOI based fast neutron source reactor

International Nuclear Information System (INIS)

Wakabayashi, Hiroaki; An, Shigehiro.

1983-01-01

Fast neutron is known as one of useful radiations for radiation therapy of tumors. Boron neutron capture therapy (BNCT) of tumors which makes use of 10 B(n, α) 7 Li reaction of 10 B compounds selectively attached to tumor cells with thermal and intermediate neutrons is another way of neutron based radiation therapy which is, above all, attractive enough to kill tumor cells selectively sparing normal tissue. In Japan, BNCT has already been applied and leaned to be effective. After more than a decade operational experiences and the specific experiments designed for therapeutical purposes, in this paper, a conceptual design of a special neutron therapy reactor facility based on YAYOI - fast neutron source reactor of Nuclear Engineering Research Laboratory, Faculty of Engineering, the University of Tokyo - modified to provide an upward beam of fast and intermediate neutrons is presented. Emphasis is placed on the in-house nature of facility and on the coordinating capability of biological and physical researches as well as maintenances of the facility. (author)

Fast Spectrum Reactors

CERN Document Server

Todd, Donald; Tsvetkov, Pavel

2012-01-01

Fast Spectrum Reactors presents a detailed overview of world-wide technology contributing to the development of fast spectrum reactors. With a unique focus on the capabilities of fast spectrum reactors to address nuclear waste transmutation issues, in addition to the well-known capabilities of breeding new fuel, this volume describes how fast spectrum reactors contribute to the wide application of nuclear power systems to serve the global nuclear renaissance while minimizing nuclear proliferation concerns. Readers will find an introduction to the sustainable development of nuclear energy and the role of fast reactors, in addition to an economic analysis of nuclear reactors. A section devoted to neutronics offers the current trends in nuclear design, such as performance parameters and the optimization of advanced power systems. The latest findings on fuel management, partitioning and transmutation include the physics, efficiency and strategies of transmutation, homogeneous and heterogeneous recycling, in addit...

A review of fast reactor activities in Italy

International Nuclear Information System (INIS)

Tavoni, R.

1996-01-01

In this paper, Italian activities on liquid metal fast reactors are shown for the period May 1995 - April 1996. During this period the ENEA collaboration with General Electric on ALMR came to an end as a consequence of the reduced effort on the design development. Nevertheless ENEA completed the studies on the PRISM Mod B oxide burner core, the neutronic configuration of which was presented at last year's meeting. Some results of the dynamic calculations are shown. ENEA participated in the IAEA/EC benchmark on the comparative calculations for severe accident in BN-800 reactor. A complete neutronic evaluation has been made including power distribution, Doppler, sodium void and material coefficients. Activities on seismic isolation are also outlined. The Italian contribution to SPX restart and operation is described; some information about the complementary convention of the Nersa society is given, together with the Italian industry participation in the SPX restart. (author)

Fast reactors

International Nuclear Information System (INIS)

Vasile, A.

2001-01-01

Fast reactors have capacities to spare uranium natural resources by their breeding property and to propose solutions to the management of radioactive wastes by limiting the inventory of heavy nuclei. This article highlights the role that fast reactors could play for reducing the radiotoxicity of wastes. The conversion of 238 U into 239 Pu by neutron capture is more efficient in fast reactors than in light water reactors. In fast reactors multi-recycling of U + Pu leads to fissioning up to 95% of the initial fuel ( 238 U + 235 U). 2 strategies have been studied to burn actinides: - the multi-recycling of heavy nuclei is made inside the fuel element (homogeneous option); - the unique recycling is made in special irradiation targets placed inside the core or at its surroundings (heterogeneous option). Simulations have shown that, for the same amount of energy produced (400 TWhe), the mass of transuranium elements (Pu + Np + Am + Cm) sent to waste disposal is 60,9 Kg in the homogeneous option and 204.4 Kg in the heterogeneous option. Experimental programs are carried out in Phenix and BOR60 reactors in order to study the feasibility of such strategies. (A.C.)

Assessment of the Dry Processed Oxide Fuel in Liquid Metal Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

Roh, Gyu Hong; Choi, Hang Bok

2005-09-15

The neutronic feasibility of the dry process oxide fuel was assessed for the sodium-cooled and lead-cooled fast reactors (SFR and LFR, respectively), which were recommended as Generation-IV (Gen-IV) reactor systems by the Gen-IV international forum. The reactor analysis was performed for the equilibrium fuel cycle of two core configurations: Hybrid BN-600 benchmark core with an enlarged lattice pitch and a modified BN-600 core. The dry process technology assumed in this study is the molten-salt process, which was developed by Russian scientists for recycling oxide fuels. The core calculation was performed by the REBUS-3 code and the reactor characteristics such as the transuranic (TRU) enrichment, breeding ratio, peak linear power, burnup reactivity swing, etc. were calculated for the equilibrium core under a fixed fuel management scheme. The results showed that a fissile self-sustainable breakeven core was achievable without blanket fuels when the fuel volume fraction was {approx}50% and most of the fission products were removed. If the design criteria used in this study is proved to be acceptable through a detailed physics design and thermal hydraulic analysis in the future, it is practically possible to construct an equilibrium fuel cycle of the SFR and LFR systems based on the oxide fuel by utilizing the dry process technology.

Assessment of the Dry Processed Oxide Fuel in Liquid Metal Fast Reactors

International Nuclear Information System (INIS)

Roh, Gyu Hong; Choi, Hang Bok

2005-09-01

The neutronic feasibility of the dry process oxide fuel was assessed for the sodium-cooled and lead-cooled fast reactors (SFR and LFR, respectively), which were recommended as Generation-IV (Gen-IV) reactor systems by the Gen-IV international forum. The reactor analysis was performed for the equilibrium fuel cycle of two core configurations: Hybrid BN-600 benchmark core with an enlarged lattice pitch and a modified BN-600 core. The dry process technology assumed in this study is the molten-salt process, which was developed by Russian scientists for recycling oxide fuels. The core calculation was performed by the REBUS-3 code and the reactor characteristics such as the transuranic (TRU) enrichment, breeding ratio, peak linear power, burnup reactivity swing, etc. were calculated for the equilibrium core under a fixed fuel management scheme. The results showed that a fissile self-sustainable breakeven core was achievable without blanket fuels when the fuel volume fraction was ∼50% and most of the fission products were removed. If the design criteria used in this study is proved to be acceptable through a detailed physics design and thermal hydraulic analysis in the future, it is practically possible to construct an equilibrium fuel cycle of the SFR and LFR systems based on the oxide fuel by utilizing the dry process technology

The fast breeder reactor

International Nuclear Information System (INIS)

Collier, J.

1990-01-01

The arguments for and against the fast breeder reactor are debated. The case for the fast reactor is that the world energy demand will increase due to increasing population over the next forty years and that the damage to the global environment from burning fossil fuels which contribute to the greenhouse effect. Nuclear fission is the only large scale energy source which can achieve a cut in the use of carbon based fuels although energy conservation and renewable sources will also be important. Fast reactors produce more energy from uranium than other types of (thermal) reactors such as AGRs and PWRs. Fast reactors would be important from about 2020 onwards especially as by then many thermal reactors will need to be replaced. Fast reactors are also safer than normal reactors. The arguments against fast reactors are largely economic. The cost, especially the capital cost is very high. The viability of the technology is also questioned. (UK)

Release of radioactive fission products from BN-600 reactor untight fuel elements

International Nuclear Information System (INIS)

Osipov, S.L.; Tsikunov, A.G.; Lisitsin, E.C.

1996-01-01

The experimental data on the release of radioactive fission products from BN-600 reactor untight fuel elements are given in the report. Various groups of radionuclides: inert gases Xe, Kr, volatile Cs, J, non-volatile Nb, and La are considered. The results of calculation-experimental study of transfer and distribution of radionuclides in the reactor primary circuit, gas system and sodium coolant are considered. It is shown that some complex radioactivity transfer processes can be described by simple mathematical models. (author)

The theoretical possibility of reducing the doubling time in a fast-reactor by using heterogeneous configurations of various types of fuel

International Nuclear Information System (INIS)

Orlov, V.V.; Slesarev, I.S.; Zaritskij, S.M.; Subbotin, S.A.; Alekseev, P.N.; Zverkov, Yu.A.

1980-01-01

The authors have derived approximate expressions relating the doubling time of a fast reactor using various types of fuel simultaneously to the doubling time of traditional (homogeneous) reactors in which these types of fuel are used separately. These relationships afford a means of determining the conditions in which the use of various types of fuel can result in an improved doubling time. It was established that the use of heterogeneous compositions formed from assemblies of homogeneous systems gives a notable gain in doubling time over that of any of the original homogeneous systems if the doubling times were similar to each other. This gain is fairly large even in the case of BN reactors with high fuel volume fractions. The size of the gain depends on the degree of ''differentiation'' in the neutron and thermal properties of the components of the heterogeneous reactor. An optimum proportion has been found for the assemblies taken from the original homogeneous systems, governed primarily by the ratio of fuel densities. Estimates were made of the advantages of metallic oxide compositions over the traditional compositions used in large, fast reactors of the BN type. These estimates indicate that the former can be considered as alternative homogeneous compositions with carbide or nitride fuel as far as breeding characteristics are concerned. (author)

The fast breeder reactor

International Nuclear Information System (INIS)

Davis, D.A.; Baker, M.A.W.; Hall, R.S.

1990-01-01

Following submission of written evidence, the Energy Committee members asked questions of three witnesses from the Central Electricity Generating Board and Nuclear Electric (which will be the government owned company running nuclear power stations after privatisation). Both questions and answers are reported verbatim. The points raised include where the responsibility for the future fast reactor programme should lie, with government only or with private enterprise or both and the viability of fast breeder reactors in the future. The case for the fast reactor was stated as essentially strategic not economic. This raised the issue of nuclear cost which has both a construction and a decommissioning element. There was considerable discussion as to the cost of building a European Fast reactor and the cost of the electricity it would generate compared with PWR type reactors. The likely demand for fast reactors will not arrive for 20-30 years and the need to build a fast reactor now is questioned. (UK)

An analysis of fast reactor fuel assembly performance taking into account their mechanical interaction in the core and refuelling line capabilities

International Nuclear Information System (INIS)

Buksha, Yu.K.; Zabudko, L.M.; Kravchenko, I.N.; Matveenko, L.V.; Meshkov, M.N.

1984-01-01

An approach to assessment of fast reactor fuel assembly performance has been considered. A concept of passive restraint of fuel assemblies in a reactor adopted in the USSR is described. Some methods for calculating the interassembly interactions during operation are briefly outlined, some calculated results are presented. A problem of fuel assembly performance during refuelling taking into account the refuelling line capabilities is considered. Some results from fuel assemblies operation experience in the BN-600 reactor are given. (author)

IAEA Technical Meeting on Innovative Heat Exchanger and Steam Generator Designs for Fast Reactors. Presentations

International Nuclear Information System (INIS)

2011-01-01

The fast reactor, which can generate electricity and breed additional fissile material for future fuel stocks, is a resource that will be needed when economic uranium supplies for the thermal reactors diminish. Further, the fast-fission fuel cycle in which material is recycled (a basic requirement to meet sustainability criteria) offers the flexibility needed to contribute decisively towards solving the problem of growing “spent” fuel inventories by greatly reducing the volume, the heat load and the radiotoxic inventory of high-level wastes that must be disposed of in long-term geological repositories. This is a waste management option that will play an increasingly important role in the future, and help to ensure that nuclear energy remains a sustainable long-term option in the world’s overall energy mix. In recognition of the fast reactor’s importance for the sustainability of the nuclear option, currently there is worldwide renewed interest in fast reactor technology development, as indicated, e.g., by the outcome of the Generation IV International Forum (GIF) technology review, which concluded with 3 out of 6 innovative systems to be fast reactors (gas cooled fast reactor, sodium cooled fast reactor, and heavy liquid metal cooled fast reactor), plus a potential fast core for a 4th concept, the super-critical water reactor. Currently, fast reactor construction projects are ongoing in India (PFBR) and Russian Federation (BN-800), whilst in China the first experimental fast reactor (CEFR) is in the commissioning phase. Fast reactor programs are also carried out in Europe (in particular in France), Japan, Republic of Korea and the USA. The most important challenges for fast reactors are in the areas of cost competitiveness with respect to LWRs and other energy sources, enhanced safety, non-proliferation, and public acceptance. With the exception of this latter, these translate into technology development challenges, i.e. the development of advanced reactor

Fast breeder reactors

International Nuclear Information System (INIS)

Waltar, A.E.; Reynolds, A.B.

1981-01-01

This book describes the major design features of fast breeder reactors and the methods used for their design and analysis. The foremost objective of this book is to fulfill the need for a textbook on Fast Breeder Reactor (FBR) technology at the graduate level or the advanced undergraduate level. It is assumed that the reader has an introductory understanding of reactor theory, heat transfer, and fluid mechanics. The book is expected to be used most widely for a one-semester general course on fast breeder reactors, with the extent of material covered to vary according to the interest of the instructor. The book could also be used effectively for a two-quarter or a two-semester course. In addition, the book could serve as a text for a course on fast reactor safety since many topics other than those appearing in the safety chapters relate to FBR safety. Methodology in fast reactor design and analysis, together with physical descriptions of systems, is emphasized in this text more than numerical results. Analytical and design results continue to change with the ongoing evolution of FBR design whereas many design methods have remained fundamentally unchanged for a considerable time

Few-group constants for the calculation of ksub(eff) and Δ(1/ksub(eff)) of fast breeder reactors

International Nuclear Information System (INIS)

Svarny, J.

1978-01-01

A theoretical and numerical analysis is presented of the linear and bilinear weighting of group constants. Special attention is paid to error accumulation in the few-group calculations of reactivity (ksub(eff)) and its first order perturbations caused by inaccuracies in weighting functions. Some theoretical conclusions are supported by calculations of the BN-600 fast breeder reactor. (author)

The prototype fast reactor

International Nuclear Information System (INIS)

Broomfield, A.M.

1985-01-01

The paper concerns the Prototype Fast Reactor (PFR), which is a liquid metal cooled fast reactor power station, situated at Dounreay, Scotland. The principal design features of a Fast Reactor and the PFR are given, along with key points of operating history, and health and safety features. The role of the PFR in the development programme for commercial reactors is discussed. (U.K.)

Fast reactors worldwide

International Nuclear Information System (INIS)

Hall, R.S.; Vignon, D.

1985-01-01

The paper concerns the evolution of fast reactors over the past 30 years, and their present status. Fast reactor development in different countries is described, and the present position, with emphasis on cost reduction and collaboration, is examined. The French development of the fast breeder type reactor is reviewed, and includes: the acquisition of technical skills, the search for competitive costs and the spx2 project, and more advanced designs. Future prospects are also discussed. (U.K.)

Fast breeder reactor research

International Nuclear Information System (INIS)

1975-01-01

Full text: The meeting was attended by 15 participants from seven countries and two international organizations. The Eighth Annual Meeting of the International Working Group on Fast Reactors (IWGFR) was attended by representatives from France, Fed. Rep. Germany, Italy, Japan, United Kingdom, Union of Soviet Socialist Republics and the United States of America - countries that have made significant progress in developing the technology and physics of sodium cooled fast reactors and have extensive national programmes in this field - as well as by representatives of the Commission of the European Communities and the IAEA. The design of fast-reactor power plants is a more difficult task than developing facilities with thermal reactors. Different reactor kinetics and dynamics, a hard neutron spectrum, larger integral doses of fuel and structural material irradiation, higher core temperatures, the use of an essentially novel coolant, and, as a result of all these factors, the additional reliability and safety requirements that are imposed on the planning and operation of sodium cooled fast reactors - all these factors pose problems that can be solved comprehensively only by countries with a high level of scientific and technical development. The exchange of experience between these countries and their combined efforts in solving the fundamental problems that arise in planning, constructing and operating fast reactors are promoting technical progress and reducing the relative expenditure required for various studies on developing and introducing commercial fast reactors. For this reason, the meeting concentrated on reviewing and discussing national fast reactor programmes. The situation with regard to planning, constructing and operating fast experimental and demonstration reactors in the countries concerned, the experience accumulated in operating them, the difficulties arising during operation and ways of over-coming them, the search for optimal designs for the power

Results and Prospects of Development of Works on Structural Core Materials for Russian Fast Reactors

International Nuclear Information System (INIS)

Nikitina, A.A.; Ageev, V.S.; Leontyeva-Smirnova, M.V.; Mitrofanova, N.M.; Tselishchev, A.V.

2015-01-01

The strategy of development of atomic energy in Russia in the first half of XXI century contemplates construction and putting in operation of fast reactors of new generation with different types of coolant: sodium (BN-800, BN-1200, MBIR), lead (BREST-OD-300) and lead-bismuth eutectic (SVBR-100). For assurance of the working capacity of reactors that are under construction and achievement of economically reasonable burn-up of nuclear fuel the structural core materials with necessary level of radiation resistance, heat resistance, corrosion resistance to products of fuel fission, corrosion resistance in coolant and in water must be developed and justified. For sodium cooled reactors the key challenge is creation of radiation resistant and heat resistant cladding materials, which must ensure the achievement of damage doses at least 140 dpa. The solution of this problem is provided by phased use as cladding materials of austenitic steels ChS68 and EK164 (maximum damage doses ~ 92 and ~110-115 dpa, respectively), precipitation-hardening heat resistant ferritic-martensitic steels EK181 and ChS139 (maximum damage dose ~140 dpa) and oxide dispersion strengthened (ODS) steels (maximum damage dose more than 140 dpa). For development of core materials for reactors with lead and lead-bismuth eutectic coolants the most serious challenge is corrosion resistance of materials in coolant. Therefore at present time a very wide range of works on study of corrosion resistance of candidate materials is carrying out. As the basic material for the cladding tubes is considered a ferritic-martensitic steel EP823 with high silicon content. In this report the main results of works on justification of the working capacity of materials of different classes in respect to use it in cores of operating and prospective fast reactors with different types of coolant and prospects of further development of works are presented. (author)

Fast reactor programme

International Nuclear Information System (INIS)

Plakman, J.C.

1982-01-01

This progress report summarizes the fast reactor research carried out by ECN during the period covering the year 1980. This research is mainly concerned with the cores of sodium-cooled breeders, in particular the SNR-300, and its related safety aspects. It comprises six items: A programme to determine relevant nuclear data of fission- and corrosion-products; A fuel performance programme comprising in-pile cladding failure experiments and a study of the consequences of loss-of-cooling and overpower; Basic research on fuel; Investigation of the changes in the mechanical properties of austenitic stainless steel DIN 1.4948 due to fast neutron doses, this material has been used in the manufacture of the reactor vessel and its internal components; Study of aerosols which could be formed at the time of a fast reactor accident and their progressive behaviour on leaking through cracks in the concrete containment; Studies on heat transfer in a sodium-cooled fast reactor core. As fast breeders operate at high power densities, an accurate knowledge of the heat transfer phenomena under single-phase and two-phase conditions is sought. (Auth.)

Knowledge management in fast reactors

International Nuclear Information System (INIS)

Kuriakose, K.K.; Satya Murty, S.A.V.; Swaminathan, P.; Raj, Baldev

2010-01-01

This paper highlights the work that is being carried out in Knowledge Management of Fast Reactors at Indira Gandhi Centre for Atomic Research (IGCAR) including a few examples of how the knowledge acquired because of various incidents in the initial years has been utilized for the successful operation of Fast Breeder Test Reactor. It also briefly refers to the features of the IAEA initiative on the preservation of Knowledge in the area of Fast Reactors in the form of 'Fast Reactor Knowledge Organization System' (FR-KOS), which is based on a taxonomy for storage and mining of Fast Reactor Knowledge. (author)

Comparison between TRU burning reactors and commercial fast reactor

International Nuclear Information System (INIS)

Fujimura, Koji; Sanda, Toshio; Ogawa, Takashi

2001-03-01

Research and development for stabilizing or shortening the radioactive wastes including in spent nuclear fuel are widely conducted in view point of reducing the environmental impact. Especially it is effective way to irradiate and transmute long-lived TRU by fast reactors. Two types of loading way were previously proposed. The former is loading relatively small amount of TRU in all commercial fast reactors and the latter is loading large amount of TRU in a few TRU burning reactors. This study has been intended to contribute to the feasibility studies on commercialized fast reactor cycle system. The transmutation and nuclear characteristics of TRU burning reactors were evaluated and compared with those of conventional transmutation system using commercial type fast reactor based upon the investigation of technical information about TRU burning reactors. Major results are summarized as follows. (1) Investigation of technical information about TRU burning reactors. Based on published reports and papers, technical information about TRU burning reactor concepts transmutation system using convectional commercial type fast reactors were investigated. Transmutation and nuclear characteristics or R and D issue were investigated based on these results. Homogeneously loading of about 5 wt% MAs on core fuels in the conventional commercial type fast reactor may not cause significant impact on the nuclear core characteristics. Transmutation of MAs being produced in about five fast reactors generating the same output is feasible. The helium cooled MA burning fast reactor core concept propose by JAERI attains criticality using particle type nitride fuels which contain more than 60 wt% MA. This reactor could transmute MAs being produced in more than ten 1000 MWe-LWRs. Ultra-long life core concepts attaining more than 30 years operation without refueling by utilizing MA's nuclear characteristics as burnable absorber and fertile nuclides were proposed. Those were pointed out that

Reactor core design optimization of the 200 MWt Pb-Bi cooled fast reactor for hydrogen production

International Nuclear Information System (INIS)

Bahrum, Epung Saepul; Su'ud, Zaki; Waris, Abdul; Fitriyani, Dian; Wahjoedi, Bambang Ari

2008-01-01

In this study reactor core geometrical optimization of 200 MWt Pb-Bi cooled long life fast reactor for hydrogen production has been conducted. The reactor life time is 20 years and the fuel type is UN-PuN. Geometrical core configurations considered in this study are balance, pancake and tall cylindrical cores. For the hydrogen production unit we adopt steam membrane reforming hydrogen gas production. The optimum operating temperature for the catalytic reaction is 540degC. Fast reactor design optimization calculation was run by using FI-ITB-CHI software package. The design criteria were restricted by the multiplication factor that should be less than 1.002, the average outlet coolant temperature 550degC and the maximum coolant outlet temperature less than 700degC. By taking into account of the hydrogen production as well as corrosion resulting from Pb-Bi, the balance cylindrical geometrical core design with diameter and height of the active core of 157 cm each, the inlet coolant temperature of 350degC and the coolant flow rate of 7000 kg/s were preferred as the best design parameters. (author)

Fast reactors: potential for power

International Nuclear Information System (INIS)

1983-02-01

The subject is discussed as follows: basic facts about conventional and fast reactors; uranium economy; plutonium and fast reactors; cooling systems; sodium coolant; safety engineering; handling and recycling plutonium; safeguards; development of fast reactors in Britain and abroad; future progress. (U.K.)

Fast Breeder Reactor studies

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.; Kittel, J.H.; Fauske, H.K.; Lineberry, M.J.; Stevenson, M.G.; Amundson, P.I.; Dance, K.D.

1980-07-01

This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts

Fast Breeder Reactor studies

Energy Technology Data Exchange (ETDEWEB)

Till, C.E.; Chang, Y.I.; Kittel, J.H.; Fauske, H.K.; Lineberry, M.J.; Stevenson, M.G.; Amundson, P.I.; Dance, K.D.

1980-07-01

This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts.

Fuel component of electricity generation cost for the BN-800 reactor with MOX fuel and uranium oxide fuel with increasing of fuel burnup and removing of radial breeding blanket

International Nuclear Information System (INIS)

Raskach, A.

2001-01-01

Nowadays there are two completed design concepts of Nuclear Power Plants (NPPs) with the BN-800 type reactors developed with due regard for advanced safety requirements. One of them is the design of the fourth unit of the Beloyarsk Nuclear Power Plant; the other one is the design of three units of the South Ural Nuclear Power Plant. The both concepts are to use mixed oxide fuel (MOX fuel) based on civil plutonium. Studies on any project include economical analyses and cost of fuel is an essential parameter. In the course of the design works on the both projects such evaluations were done. For BN-800 on the Beloyarsk site nuclear fuel costs were taken from actual expenses of the BN-600 reactor and converted to rated thermal power and design capacity factor of the BN-800 and then increased by 20% in connection with turning to MOX fuel. Then this methodology was rewarding, but the ratio of uranium fuel and MOX fuel costs might change for the last years. For the project of three units of the South Ural Nuclear Power Plant nuclear fuel expenses were calculated from the data on a MOX fuel fabrication production facility (Complex-300). However, investigations performed recently shown that the methodology of economical assessments should be revised, as well as design and technology of MOX fuel fabrication at Complex-300 should be revised to meet all the existing safety requirements. Excepting there is a great bulk of civil plutonium to be reproduced, now we came up against the problem to utilize the exceeding ex-weapons plutonium that obviously can be used for MOX fuel fabrication as well. Construction of the MOX fuel fabrication facility - Complex-300 - was started in 1983. Its design output was planned to provide simultaneously 4 fast reactors of the BN-800 type with MOX fuel. By now about 50% of construction works (taking into account auxiliary buildings and arrangements) and 20% of installation works have been done at Complex-300. Along this, first works to construct

Optimal reactor strategy for commercializing fast breeder reactors

International Nuclear Information System (INIS)

Yamaji, Kenji; Nagano, Koji

1988-01-01

In this paper, a fuel cycle optimization model developed for analyzing the condition of selecting fast breeder reactors in the optimal reactor strategy is described. By dividing the period of planning, 1966-2055, into nine ten-year periods, the model was formulated as a compact linear programming model. With the model, the best mix of reactor types as well as the optimal timing of reprocessing spent fuel from LWRs to minimize the total cost were found. The results of the analysis are summarized as follows. Fast breeder reactors could be introduced in the optimal strategy when they can economically compete with LWRs with 30 year storage of spent fuel. In order that fast breeder reactors monopolize the new reactor market after the achievement of their technical availability, their capital cost should be less than 0.9 times as much as that of LWRs. When a certain amount of reprocessing commitment is assumed, the condition of employing fast breeder reactors in the optimal strategy is mitigated. In the optimal strategy, reprocessing is done just to meet plutonium demand, and the storage of spent fuel is selected to adjust the mismatch of plutonium production and utilization. The price hike of uranium ore facilitates the commercial adoption of fast breeder reactors. (Kako, I.)

Analysis for mechanical consequences of a core disruptive accident in Prototype Fast Breeder Reactor

International Nuclear Information System (INIS)

Chellapandi, P.; Velusamy, K.; Chetal, S.C.; Bhoje, S.B.; Lal, H.; Sethi, V.S.

2003-01-01

The mechanical consequences of a core disruptive accident (CDA) in a fast breeder reactor are described. The consequences are development of deformations and strains in the vessels, intermediate heat exchangers (IHX) and decay heat exchangers (DHX), impact of sodium slug on the bottom surface of the top shield, sodium release to reactor containment building through top shield penetrations, sodium fire and consequent temperature and pressure rise in reactor containment building (RCB). These are quantified for 500 MWe Prototype Fast Breeder Reactor (PFBR) for a CDA with 100 MJ work potential. The results are validated by conducting a series of experiments on 1/30 and 1/13 scaled down models with increasing complexities. Mechanical energy release due to nuclear excursion is simulated by chemical explosion of specially developed low density explosive charge. Based on these studies, structural integrity of primary containment, IHX and DHX is demonstrated. The sodium release to RCB is 350 kg which causes pressure rise of 12 kPa in RCB. (author)

Accidental situations analysis in BN-800 reactor bounded with an untimely ascension of the control rods

International Nuclear Information System (INIS)

Gorbunov, V.S.; Zaets, N.P.

1987-12-01

In this document the conditions and the results of one or more control rods untimely ascension out of the BN-800 core are examined. The mathematical model which describes the reactor kinetic, the temperature core and the feedback is presented [fr

Fast reactor development programme in France during 1995

International Nuclear Information System (INIS)

Le Rigoleur, C.

1996-01-01

In 1995, the total amount of electricity produced in France was 471 TWh, out of which 358.2 TWh (76 %) were produced by nuclear power plants, 36.9 TWh (7.8 %) by conventional thermal plants, and 75.5 TWh (16 %) by hydraulic plants. The net electrical power consumption was 368.7 TWh. At the end of 1995, 'Electricite de France' had 54 PWR units in operation. The availability factor for these units was maintained at 81%. 1995 was marked by a decrease of unexpected shutdowns (1.8% in 1995 instead of 2.2% in 1994), a new reduction in programmed shutdown periods, and a good safety level was maintained. In the field of Fast Reactors, the main events of 1995 were the following. At the end of December 1994, the PHENIX reactor was authorized to perform its 49th cycle at 350 MW th (143 MWe). This 49th cycle was completed without any significant problems on April 7, 1995. During the remainder of the year, the reactor had been shut down in order to carry out several tasks within the scope of the ten-year extension of the PHENIX reactor's lifetime. Concerning the CREYS-MALVILLE plant (SUPER-PHENIX) the first part of the year was devoted to repairing argon leak of one of the IHX. Authorization to restart the reactor was given on August 22. The end of the year was beset by a number of minor incidents. The reactor was restarted at the end of 1995 and reactor power was increased by successive steps (30% Pn (Nominal Power) up to February 6 1996; followed by 50 %...). The 'Decret d'Autorisation de Creation' stipulates that because of its prototype character, SUPER PHENIX will have to be operated under conditions explicitly giving priority to safety and knowledge acquisition, with an objective of research and demonstration. In this context, the so-called 'knowledge acquisition' programme designed to prove the capacity of a large FBR to produce electricity on an industrial scale, to test the consumption of plutonium and minor actinides in a large fast reactor, as well as to provide

Fast breeder reactors an engineering introduction

CERN Document Server

Judd, A M

1981-01-01

Fast Breeder Reactors: An Engineering Introduction is an introductory text to fast breeder reactors and covers topics ranging from reactor physics and design to engineering and safety considerations. Reactor fuels, coolant circuits, steam plants, and control systems are also discussed. This book is comprised of five chapters and opens with a brief summary of the history of fast reactors, with emphasis on international and the prospect of making accessible enormous reserves of energy. The next chapter deals with the physics of fast reactors and considers calculation methods, flux distribution,

Power from plutonium: fast reactor fuel

International Nuclear Information System (INIS)

Bishop, J.F.W.

1981-01-01

Points of similarity and of difference between fast reactor fuel and fuels for AGR and PWR plants are established. The flow of uranium and plutonium in fast and thermal systems is also mentioned, establishing the role of the fast reactor as a plutonium burner. A historical perspective of fast reactors is given in which the substantial experience accumulated in test and prototype is indicated and it is noted that fast reactors have now entered the commercial phase. The relevance of the data obtained in the test and prototype reactors to the behaviour of commercial fast reactor fuel is considered. The design concepts employed in fuel are reviewed, including sections on core support styles, pin support and pin detail. This is followed by a discussion of current issues under the headings of manufacture, performance and reprocessing. This section includes a consideration of gel fuel, achievable burn-up, irradiation induced distortions and material choices, fuel form, and fuel failure mechanisms. Future development possibilities are also discussed and the Paper concludes with a view on the logic of a UK fast reactor strategy. (U.K.)

Comparison of fuel cycles characteristics for nuclear energy systems based on WWER-TOI and BN-1200 reactors

International Nuclear Information System (INIS)

Kagramanyan, V.S.; Kalashnikov, A.G.; Kapranova, Eh.N.; Puzakov, A.Yu.

2014-01-01

Authors determine the characteristics of the fuel cycle (FC) based on stationary nuclear power system based on WWER-TOI and BN-1200 reactors with fuel of different composition. Characteristics of reactor systems with partial or complete spent nuclear fuel reprocessing and recycling of plutonium are compared to those of the reference system consisting only of WWER-TOI with uranium oxide fuel, operating in an open FC [ru

Fast reactor physics - an overview

International Nuclear Information System (INIS)

Lee, S.M.

2004-01-01

An introduction to the basic features of fast neutron reactors is made, highlighting the differences from the more conventional thermal neutron reactors. A discussion of important feedback reactivity mechanisms is given. Then an overview is presented of the methods of fast reactor physics, which play an important role in the successful design and operation of fast reactors. The methods are based on three main elements, namely (i) nuclear data bases, (ii) numerical methods and computer codes, and (iii) critical experiments. These elements are reviewed and the present status and future trends are summarized. (author)

Design analysis of various transportation package options for BN-350 SNF in terms of nuclear radiation safety in planning for long-terms dry storage

International Nuclear Information System (INIS)

Aisabekov, A.Z.; Mukenova, S.A.; Tur, E.S.; Tsyngaev, V.M.

2004-01-01

Full text: This effort is performed under the BN-350 reactor facility decommissioning project. One of the project tasks - spent nuclear fuel handling - includes the following: fuel packaging into sealed canisters, transportation of the canisters in multi-seat metallo-concrete containers and placement of the containers for a long-term dry storage. The goal of this effort is to computationally validate nuclear and radiation safety of the SNF containers placed for storage both under normal storage conditions and probable accident situations. The basic unit structure and design configurations are presented: assemblies, canisters, transportation containers. The major factors influencing nuclear and radiation safety are presented: fuel burn-up, enrichment, fabrication tolerance, types of fuel assemblies, configuration of assemblies in the canister and canisters in the container, background of assemblies placed in the reactor and cooling pool. Conditions under which the SNF containers will be stored are described and probable accident situations are listed. Proceeding from the conservatism principle, selection of the assemblies posing the greatest nuclear hazard is validated. A neutron effective multiplication factor is calculated for the SNF containers under the normal storage conditions and for the case of emergency. The effective multiplication factor is shown to be within a standard value of 0.95 in any situation. Based on the experimental data on assembly and canister dose rates, canisters posing the highest radiation threat are selected. Activities of sources and gamma-radiation spectral composition are calculated. Distribution of the dose rate outside the containers both under the normal storage conditions and accident situations are calculated. The results obtained are analyzed

Status of national programmes on fast reactors

International Nuclear Information System (INIS)

1994-04-01

Based on the International Working Group on Fast reactors (IWGFR) members' request, the IAEA organized a special meeting on Fast Reactor Development and the Role of the IAEA in May 1993. The purpose of the meeting was to review and discuss the status and recent development, to present major changes in fast reactor programmes and to recommend future activities on fast reactors. The IWGFR took note that in some Member States large prototypes have been built or are under construction. However, some countries, due to their current budget constraints, have reduced the level of funding for research and development programmes on fast reactors. The IWGFR noted that in this situation the international exchange of information and cooperation on the development of fast reactors is highly desirable and stressed the importance of the IAEA's programme on fast reactors. These proceedings contain important and useful information on national programmes and new developments in sodium cooled fast reactors in Member States. Refs, figs and tabs

The fast breeder reactor

International Nuclear Information System (INIS)

Patterson, W.

1990-01-01

The author criticises the United Kingdom Atomic Energy Authority's fast breeder reactor programme in his evidence to the House of Commons Select Committee on Energy in January 1990. He argues for power generation by renewable means and greater efficiency in the use rather than in the generation of electricity. He refutes the arguments for nuclear power on the basis of reduced global warming as he claims support technology produces significant amounts of carbon dioxide in any case. Serious doubts are raised about the costs of a fast breeder reactor programme compared to, say, generation by pressurised water reactors. The idea of a uranium scarcity in several decades is also refuted. The reliability of fast breeder reactor technology is called into question. He argues against reprocessing plutonium for economic, health and safety reasons. (UK)

New fast reactor installation concept

International Nuclear Information System (INIS)

Anon.

1976-01-01

The large size and complexity of fast reactor installations are emphasised and these difficulties will be increased with the advent of fast reactors of higher power. In this connection a new concept of fast reactor installation is described with a view to reducing the size of the installation and enabling most components, including even the primary vessel, to be constructed within the confines of a workshop. Full constructional details are given. (U.K.)

Review of fast reactor activities in India

International Nuclear Information System (INIS)

Paranjpe, S.R.

1982-01-01

A review of fast reactor activities in India is introduced. One stage of construction of the Fast Breeder Test Reactor (FBTR) and design studies for 500MWe Prototype Fast Breeder Reactor (PFBR) are briefly summarized. The emphasis is on fast reactor physics, materials studies, radiochemistry, and the safety and fuel reprocessing programme

Safeguards challenges of Fast Breeder Reactor

International Nuclear Information System (INIS)

Ko, H. S.

2010-01-01

Although the safeguards system of Sodium Fast Reactor (SFR) seems similar to that of Light Water Reactor (LWR), it was raised safeguards challenges of SFR that resulted from the visual opacity of liquid sodium, chemical reactivity of sodium and other characteristics of fast reactor. As it is the basic concept stage of the safeguards of SFR in Korea, this study tried to analyze the latest similar study of safeguards issues of the Fast Breeder Reactor (FBR) at Joyo and Monju in Japan. For this reason, this study is to introduce some potential safeguards challenges of Fast Breeder Reactor. With this analysis, future study could be to address the safeguards challenges of SFR in Korea

Advanced Safeguards Approaches for New Fast Reactors

International Nuclear Information System (INIS)

Durst, Philip C.; Therios, Ike; Bean, Robert; Dougan, A.; Boyer, Brian; Wallace, Rick L.; Ehinger, Michael H.; Kovacic, Don N.; Tolk, K.

2007-01-01

This third report in the series reviews possible safeguards approaches for new fast reactors in general, and the ABR in particular. Fast-neutron spectrum reactors have been used since the early 1960s on an experimental and developmental level, generally with fertile blanket fuels to 'breed' nuclear fuel such as plutonium. Whether the reactor is designed to breed plutonium, or transmute and 'burn' actinides depends mainly on the design of the reactor neutron reflector and the whether the blanket fuel is 'fertile' or suitable for transmutation. However, the safeguards issues are very similar, since they pertain mainly to the receipt, shipment and storage of fresh and spent plutonium and actinide-bearing 'TRU'-fuel. For these reasons, the design of existing fast reactors and details concerning how they have been safeguarded were studied in developing advanced safeguards approaches for the new fast reactors. In this regard, the design of the Experimental Breeder Reactor-II 'EBR-II' at the Idaho National Laboratory (INL) was of interest, because it was designed as a collocated fast reactor with a pyrometallurgical reprocessing and fuel fabrication line--a design option being considered for the ABR. Similarly, the design of the Fast Flux Facility (FFTF) on the Hanford Site was studied, because it was a successful prototype fast reactor that ran for two decades to evaluate fuels and the design for commercial-scale fast reactors

Fast reactors: the industrial perspective

International Nuclear Information System (INIS)

Vaughan, R.D.

1986-01-01

Industrial participation in the development of the fast reactor is reviewed, from the construction of PFR at Dounreay to the initial steps towards collaboration in Europe. The optimum design of the fast reactor has changed considerably from the days when it was needed urgently to forestall a shortage of uranium to today when uranium is abundant and cheap. The evolution of the reactor design over this period is described. Collaboration in Europe is shown to be the only answer to high development costs and the search for a reactor which will compete with thermal reactors in today's environment. The partner countries in this collaboration are all motivated differently, and this is leading to some delays in concluding the necessary agreements. The objective on the industrial front is now to participate in the two or three demonstration fast reactors that will be built in Europe during the remainder of the century leading, it is hoped, to a competitive reactor design by the year 2000. (author)

Transmutation of Americium in Fast Neutron Facilities

OpenAIRE

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on c...

A fast and flexible reactor physics model for simulating neutron spectra and depletion in fast reactors - 202

International Nuclear Information System (INIS)

Recktenwald, G.D.; Bronk, L.A.; Deinert, M.R.

2010-01-01

Determining the time dependent concentration of isotopes within a nuclear reactor core is central to the analysis of nuclear fuel cycles. We present a fast, flexible tool for determining the time dependent neutron spectrum within fast reactors. The code (VBUDS: visualization, burnup, depletion and spectra) uses a two region, multigroup collision probability model to simulate the energy dependent neutron flux and tracks the buildup and burnout of 24 actinides, as well as fission products. While originally developed for LWR simulations, the model is shown to produce fast reactor spectra that show high degree of fidelity to available fast reactor benchmarks. (authors)

Fast reactor fuel reprocessing in the UK

International Nuclear Information System (INIS)

Allardice, R.H.; Williams, J.; Buck, C.

1977-01-01

Enriched uranium metal fuel irradiated in the Dounreay Fast Reactor has been reprocessed and refabricated in plants specifically designed for the purpose in the U.K. since 1961. Efficient and reliable fuel recycle is essential to the development of a plutonium based fast reactor system and the importance of establishing at an early stage fast reactor fuel reprocessing has been reinforced by current world difficulties in reprocessing high burn-up thermal reactor oxide fuel. In consequence, the U.K. has decided to reprocess irradiated fuel from the 250 MW(E) Prototype Fast Reactor as an integral part of the fast reactor development programme. Flowsheet and equipment development work for the small scale fully active demonstration plant have been carried out over the past 5 years and the plant will be commissioned and ready for active operation during 1977. In parallel, a comprehensive waste management system has been developed and installed. Based on this development work and the information which will arise from active operation of the plant a parallel development programme has been initiated to provide the basis for the design of a large scale fast reactor fuel reprocessing plant to come into operation in the late 1980s to support the projected U.K. fast reactor installation programme. The paper identifies the important differences between fast reactor and thermal reactor fuel reprocessing technologies and describes some of the development work carried out in these areas for the small scale P.F.R. fuel reprocessing operation. In addition, the development programme in aid of the design of a larger scale fast reactor fuel reprocessing plant is outlined and the current design philosophy is discussed

Advanced Safeguards Approaches for New Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

Durst, Philip C.; Therios, Ike; Bean, Robert; Dougan, A.; Boyer, Brian; Wallace, Rick L.; Ehinger, Michael H.; Kovacic, Don N.; Tolk, K.

2007-12-15

This third report in the series reviews possible safeguards approaches for new fast reactors in general, and the ABR in particular. Fast-neutron spectrum reactors have been used since the early 1960s on an experimental and developmental level, generally with fertile blanket fuels to “breed” nuclear fuel such as plutonium. Whether the reactor is designed to breed plutonium, or transmute and “burn” actinides depends mainly on the design of the reactor neutron reflector and the whether the blanket fuel is “fertile” or suitable for transmutation. However, the safeguards issues are very similar, since they pertain mainly to the receipt, shipment and storage of fresh and spent plutonium and actinide-bearing “TRU”-fuel. For these reasons, the design of existing fast reactors and details concerning how they have been safeguarded were studied in developing advanced safeguards approaches for the new fast reactors. In this regard, the design of the Experimental Breeder Reactor-II “EBR-II” at the Idaho National Laboratory (INL) was of interest, because it was designed as a collocated fast reactor with a pyrometallurgical reprocessing and fuel fabrication line – a design option being considered for the ABR. Similarly, the design of the Fast Flux Facility (FFTF) on the Hanford Site was studied, because it was a successful prototype fast reactor that ran for two decades to evaluate fuels and the design for commercial-scale fast reactors.

Low-pressure c-BN deposition - is a CVD process possible?

International Nuclear Information System (INIS)

Haubner, R.; Tang, X.

2001-01-01

Since the low-pressure diamond deposition was discovered in 1982 there is a high interest to find a similar process for the c-BN synthesis. A review about the c-BN deposition process as well as its characterization is given. Experiments with a simple chemical vapor deposition(CVD) reactor using tris(dimethylamino)borane as precursor were carried out. In a cold-wall reactor substrates were heated up by high-frequency. Argon was used as protecting and carrying the precursor, it was saturated with tris(dimethylamino)borane (precursor) according to its vapor pressure and transports the pressure to the hot substrate, where deposition occurs. WC-Co hardmetal plates containing 6 wt. % Co, Mo and Si were used as substrates. Various BN layers were deposited and characterized. X-ray diffraction, IR-spectroscopy and SIMS indicate that BN-coatings containing c-BN were deposited. However a final verification of c-BN crystallites by TEM investigations was not possible till now. (nevyjel)

Fast reactor fuel reprocessing. An Indian perspective

International Nuclear Information System (INIS)

Natarajan, R.; Raj, Baldev

2005-01-01

The Department of Atomic Energy (DAE) envisioned the introduction of Plutonium fuelled fast reactors as the intermediate stage, between Pressurized Heavy Water Reactors and Thorium-Uranium-233 based reactors for the Indian Nuclear Power Programme. This necessitated the closing of the fast reactor fuel cycle with Plutonium rich fuel. Aiming to develop a Fast Reactor Fuel Reprocessing (FRFR) technology with low out of pile inventory, the DAE, with over four decades of operating experience in Thermal Reactor Fuel Reprocessing (TRFR), had set up at the India Gandhi Center for Atomic Research (IGCAR), Kalpakkam, R and D facilities for fast reactor fuel reprocessing. After two decades of R and D in all the facets, a Pilot Plant for demonstrating FRFR had been set up for reprocessing the FBTR (Fast Breeder Test Reactor) spent mixed carbide fuel. Recently in this plant, mixed carbide fuel with 100 GWd/t burnup fuel with short cooling period had been successfully reprocessed for the first time in the world. All the challenging problems encountered had been successfully overcome. This experience helped in fine tuning the designs of various equipments and processes for the future plants which are under construction and design, namely, the DFRP (Demonstration Fast reactor fuel Reprocessing Plant) and the FRP (Fast reactor fuel Reprocessing Plant). In this paper, a comprehensive review of the experiences in reprocessing the fast reactor fuel of different burnup is presented. Also a brief account of the various developmental activities and strategies for the DFRP and FRP are given. (author)

Status of National Programmes on Fast Breeder Reactors. International Working Group on Fast Reactors Twenty-First Annual Meeting, Seattle, USA, 9-12 May 1988

International Nuclear Information System (INIS)

1988-11-01

The following papers on the status of national programmes on fast breeder reactors are presented in this report: Fast breeder reactor development in France during 1987; Status of fast breeder reactor development in the Federal Republic of Germany, Belgium and the Netherlands; A review of the Indian fast reactor programme; A review of the Italian fast reactor programme; A review of the fast reactor programme in Japan; Status of fast reactor activities in the USSR; A review of the United Kingdom fast reactor programme; Status of liquid metal reactor development in the United States of America; Review of activities of the Commission of European Communities relating to fast reactors in 1987; European co-operation in the field of fast reactor research and development — 1987 progress report; A review of fast reactor activities in Switzerland

Uranium and the fast reactor

International Nuclear Information System (INIS)

Price, T.

1982-01-01

The influence of uranium availability upon the future of the fast reactor is reviewed. The important issues considered are uranium reserves and resources, uranium market prices, fast reactor economics and the political availability of uranium to customers in other countries. (U.K.)

Fast reactor collaboration in Europe

International Nuclear Information System (INIS)

Smith, G.E.I.

1987-01-01

Fast reactors have been developed in several European countries, the United Kingdom, France, Germany and Italy. A suggestion to collaborate on fast reactor research and development resulted in an Intergovernmental Memorandum of Understanding signed in 1984 by the UK, France, Germany, Italy and Belgium. Holland was expected to join later. This provided for co-operation between electric utilities, reactor design, research and development companies and fuel cycle companies. Three steering committees have so far been set up, the European fast reactor utilities Group, the European research and development and the European fuel cycle steering committees. Progress on these is detailed. The main areas of technology exchange are listed in the Appendix. The possibility exists for a series of three large demonstration plants to be built in Europe and a fuel reprocessing plant to confirm the reactor system. (U.K.)

Fast pyrolysis of sugarcane and cassava residues in a free-fall reactor

International Nuclear Information System (INIS)

Pattiya, Adisak; Sukkasi, Sittha; Goodwin, Vituruch

2012-01-01

Fast pyrolysis of agricultural residues from sugarcane and cassava plantations was carried out in a laboratory-scale free-fall reactor unit. The objectives of this work were to investigate the effects of biomass types and pyroysis conditions, such as reactor temperature, condensation temperature, nitrogen flow rate and run duration, on pyrolysis product distribution, as well as to study the basic properties of the products. The results showed that all of the parameters affected the product distribution. The optimum reactor temperatures for maximising bio-oil yield were in the range of 350–450 °C. About 70 wt% of bio-oil yield could be obtained by pyrolysis of cassava stalk at a reactor temperature of 450 °C and a primary condensation temperature of 10 °C. It was also found that the minimum flow rate of nitrogen for obtaining high bio-oil yield was 1.5 l/min. The product characterisation showed that the bio-oil and char produced from the agricultural residues with the free-fall reactor unit were to a certain extent similar to those produced from different types of biomass with different types of pyrolysis reactor configurations. -- Highlights: ► Fast pyrolysis of sugarcane and cassava agricultural residues was carried out in a laboratory-scale free-fall reactor unit. ► The effects of process parameters on product yields were investigated. ► The process parameters included reactor temperature, condensation temperature, nitrogen flow rate and run duration. ► Basic properties of pyrolysis products were examined.

Fast breeder reactors--lecture 4

International Nuclear Information System (INIS)

Marshall, W.; Davies, L.M.

1986-01-01

This paper discusses the economics of fast breeder reactors. An algebraic background is presented which represents the various views expressed by different nations regarding the cost of fast breeder reactors and their associated fuel cycle services, the timescale by which they might be available, and the simultaneous variations in the price of uranium. Actual presentations made by individual countries in recent discussions serve to verify the general nature of this present discussion. It is assumed that if nuclear power is to make a long term contribution to the needs of the world, the introduction of fast breeder reactors is both essential and necessary

Astrid (fast breeder nuclear reactor)

International Nuclear Information System (INIS)

2014-01-01

This document presents ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration), a French project of sodium-cooled fast breeder reactor, fourth generation reactor which should be fuelled by uranium 238 rather than uranium 235, and should therefore need less extracted natural uranium to produce electricity. The operation principle of fast breeder reactors is described. They notably directly consume plutonium, allow an easier radioactive waste management as they transform long life radioactive elements into shorter life elements by transmutation. The regeneration process is briefly described, and the various operation modes are evoked (iso-generator, sub-generator, and breeder). Some peculiarities of sodium-cooled reactors are outlined. The Astrid operation principle is described, its main design innovations outlined. Various challenges are discussed regarding safety of supply and waste processing, and the safety of future reactors. Major actors are indicated: CEA, Areva, EDF, SEIV Alcen, Toshiba, Rolls Royce, and Comex. Some key data are indicated: expected lifetime, expected availability rate, cost. The projected site is Marcoule and fast breeder reactors operated or under construction in the world are indicated. The document also proposes an overview of the background and evolution of reactors of 4. generation

Integral fast reactor

International Nuclear Information System (INIS)

Chang, Y.I.

1989-01-01

The Integral Fast Reactor (IFR) is an innovative liquid metal reactor concept being developed at Argonne National Laboratory. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system. This paper describes the key features and potential advantages of the IFR concept, with emphasis on its safety characteristics

The safety of fast reactors

International Nuclear Information System (INIS)

Justin, F.

1976-01-01

A response is made to the main questions that a man in the street may arise concerning fast breeder reactors, in particular: the advantages of this line, dangerous materials contained in fast breeder reactors, containment shells protecting the environment from radiations, main studies now in progress [fr

The fast breeder reactor

International Nuclear Information System (INIS)

Keck, O.

1984-01-01

Nowadays the fast-breeder reactor is a negative symbol of advanced technology which is getting out of control and, due to its complexity, is incomprehensible for politicians and therefore by-passes the established order. The author lists the most important decisions over state aid to the fast-breeder-reactors up until the mid-seventies and uses documents from the appropriate advisory bodies as reference. He was also aided by interviews with those directly involved with the project. The empirical facts forces us to discard our traditional view of the relationship between state and industry with regard to advanced technology. The author explains that it is impossible to find any economic value in the fast-breeder reactor. The insight gained through this project allows him to draw conclusions which apply to all aspects of state aid to advanced technology. (orig.) [de

Economic Issues of Fast Reactor in China

International Nuclear Information System (INIS)

Yang Hongyi

2013-01-01

Conclusions: 1. More and more fast reactors could be appearing in the world currently and near future. 2. China gets little experience and practice about the economics issues of sodium cooled fast reactors. 3. The economic issues become more and more important for the deplot of fast reactors. Suggestions: 1. An authoritative economic evaluation solution for fast reactor and related fuel cycles facilities is necessary. The solution may be developed by the interested country in order to share the few data, experience and methodology. 2. A new initiative to help to share the economic information for fast reactor and related fuel cycle facilities is necessary. A meeting like TM-44899 organized by the IAEA is very beneficial for this topic and hopefully will continue

The integral fast reactor

International Nuclear Information System (INIS)

Till, C.E.

1987-01-01

On April 3rd, 1986, two dramatic demonstrations of the inherent capability of sodium-cooled fast reactors to survive unprotected loss of cooling accidents were carried out on the experimental sodium-cooled power reactor, EBR-II, on the Idaho site of Argonne National Laboratory. Transients potentially of the most serious kind, one an unprotected loss of flow, the other an unprotected loss of heat sink, both initiated from full power. In both cases the reactor quietly shut itself down, without damage of any kind. These tests were a part of the on-going development program at Argonne to develop an advanced reactor with significant new inherent safety characteristics. Called the Integral Fast Reactor, or IFR, the basic thrust is to develop everything that is needed for a complete nuclear power system - reactor, closed fuel cycle, and waste processing - as a single optimized entity, and, for simplicity in concept, as an integral part of a single plant. The particular selection of reactor materials emphasizes inherent safety characteristics and also makes possible a simplified closed fuel cycle and waste process improvements

International conference on fast reactors and related fuel cycles (FR09): Challenges and opportunities. CN-176 presentations

International Nuclear Information System (INIS)

2009-01-01

Renewed interest in nuclear energy is driven by the need to develop carbon free energy sources, by demographics and development in emerging economies, as well as by security of supply concerns. It is expected that nuclear energy will deliver huge amounts of energy to both emerging and developed economies. However, acceptance of large scale contributions would depend on satisfaction of key drivers to enhance sustainability in terms of economics, safety, adequacy of natural resources, waste reduction, non-proliferation and public acceptance. Fast spectrum reactors with recycle enhance the sustainability indices significantly. This has led to the focus on fast spectrum reactors with recycle in the Generation IV International Forum (GIF) and the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) initiative of the IAEA. It is expected that 2009 will register major events in the domain of fast spectrum reactors, that is, the restart of Monju in Japan, the first criticality of the China Experimental Fast Reactor in China, as well as new insights through end-of-life studies in Phenix, France. New fast reactors are expected to be commissioned in the near future: the 500 MW(e) Prototype Fast Breeder Reactor in India and the BN-800 unit in the Russian Federation. Moreover, China, France, India, Japan, Republic of Korea and the United States of America are preparing advanced prototypes/ demonstrations and/or commercial reactors for the 2020-2030 horizon. The necessary condition for successful fast reactor deployment in the near and mid-term is the understanding and assessment of innovative technological and design options, based on both past knowledge and experience, as well as on ongoing research and technology development efforts. In this respect, the need for in-depth international information exchange is underscored by the fact that the last large international fast reactor conference was held as far back as 1991. Since then, progress in research

The energy gap and the fast reactor

International Nuclear Information System (INIS)

Hill, J.

1977-01-01

The background to the development of fast reactors is summarized. In Britain, the results of the many experiments performed, the operation of the Dounreay Fast Reactor for the past 18 years and the first year's operation of the larger Prototype Fast Reactor have all been very encouraging, in that they demonstrated that the performance corresponded well with predictions, breeding is possible, and the system is exceptionally stable in operation. The next step in fast reactor engineering is to build a full-scale fast reactor power station. There would seem to be little reason to expect more trouble than could reasonably be expected in constructing any large project of this general nature. However, from an engineering point of view continuity of experience is required. If a decision to build a commercial fast reactor were taken today there would be a 14-year gap between strating this and the start of the Prototype Fast Reactor. This is already much too long. From an environmental standpoint we have to demonstrate that we can manufacture and reprocess fast reacctor fuel for a substantial programme in a way that does not lead to pollution of the environment, and that plutonium-containing fuel can be transported in the quantities required in safety and in a way that does not attract terrorists or require a private army to ensure its security. Finally, we have to find a way to allow many countries to obtain the energy they need from fast reactors, without leading to the proliferation of nuclear weapons or weapons capability. (author)

Introduction of the experimental fast reactor JOYO

International Nuclear Information System (INIS)

Matsuba, Ken-ichi; Kawahara, Hirotaka; Aoyama, Takafumi

2006-01-01

The experimental fast reactor JOYO at O-arai Engineering Center of Japan Nuclear Cycle Development Institute is the first liquid metal cooled fast reactor in Japan. This paper describes the plant outline, experiences on the fast reactor technology and test results accumulated through twenty eight years successful operation of JOYO. (author)

The fast reactor and energy supply

International Nuclear Information System (INIS)

1979-01-01

The progress made with fast reactor development in many countries is summarised showing that the aim is to provide to the nation concerned an ability to instal fast reactor power stations at the end of this century or early in the next one. Accepting the importance of fast reactors as a potential independent source of energy, problems concerning economics, industrial capability, technical factors, public acceptibility and in particular plutonium management, are discussed. It is concluded that although fast reactors have reached a comparatively advanced stage of development, a number of factors make it likely that their introduction for electricity generation will be a gradual process. Nevertheless it is necessary to complete demonstration and development phases in good time. (U.K.)

Status of Fast Reactor Research and Technology Development

International Nuclear Information System (INIS)

2012-01-01

In 1985, the International Atomic Energy Agency (IAEA) published a report titled 'Status of Liquid Metal Cooled Fast Breeder Reactors' (Technical Reports Series No. 246). The report was a general review of the status of fast reactor development at that time, covering some aspects of design and operation and reviewing experience from the earliest days. It summarized the programmes and plans in all countries which were pursuing the development of fast reactors. In 1999, the IAEA published a follow-up report titled 'Status of Liquid Metal Cooled Fast Reactor Technology' (IAEA-TECDOC-1083), necessitated by the substantial advances in fast reactor technology development and changes in the economic and regulatory environment which took place during the period of 1985-1998. Chief among these were the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at a high burnup and the launch of new fast reactor programmes by some additional Member States. In 2006, the Technical Working Group on Fast Reactors (TWG-FR) identified the need to update its past publications and recommended the preparation of a new status report on fast reactor technology. The present status report intends to provide comprehensive and detailed information on the technology of fast neutron reactors. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction, operation and decommissioning; various areas of research and development; engineering; safety; and national strategies and public acceptance of fast reactors.

Status of Fast Reactor Research and Technology Development

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-04-01

In 1985, the International Atomic Energy Agency (IAEA) published a report titled 'Status of Liquid Metal Cooled Fast Breeder Reactors' (Technical Reports Series No. 246). The report was a general review of the status of fast reactor development at that time, covering some aspects of design and operation and reviewing experience from the earliest days. It summarized the programmes and plans in all countries which were pursuing the development of fast reactors. In 1999, the IAEA published a follow-up report titled 'Status of Liquid Metal Cooled Fast Reactor Technology' (IAEA-TECDOC-1083), necessitated by the substantial advances in fast reactor technology development and changes in the economic and regulatory environment which took place during the period of 1985-1998. Chief among these were the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at a high burnup and the launch of new fast reactor programmes by some additional Member States. In 2006, the Technical Working Group on Fast Reactors (TWG-FR) identified the need to update its past publications and recommended the preparation of a new status report on fast reactor technology. The present status report intends to provide comprehensive and detailed information on the technology of fast neutron reactors. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction, operation and decommissioning; various areas of research and development; engineering; safety; and national strategies and public acceptance of fast reactors.

Status of Fast Reactor Research and Technology Development

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

In 1985, the International Atomic Energy Agency (IAEA) published a report titled 'Status of Liquid Metal Cooled Fast Breeder Reactors' (Technical Reports Series No. 246). The report was a general review of the status of fast reactor development at that time, covering some aspects of design and operation and reviewing experience from the earliest days. It summarized the programmes and plans in all countries which were pursuing the development of fast reactors. In 1999, the IAEA published a follow-up report titled 'Status of Liquid Metal Cooled Fast Reactor Technology' (IAEA-TECDOC-1083), necessitated by the substantial advances in fast reactor technology development and changes in the economic and regulatory environment which took place during the period of 1985-1998. Chief among these were the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at a high burnup and the launch of new fast reactor programmes by some additional Member States. In 2006, the Technical Working Group on Fast Reactors (TWG-FR) identified the need to update its past publications and recommended the preparation of a new status report on fast reactor technology. The present status report intends to provide comprehensive and detailed information on the technology of fast neutron reactors. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction, operation and decommissioning; various areas of research and development; engineering; safety; and national strategies and public acceptance of fast reactors.

Status of Fast Reactor Research and Technology Development

International Nuclear Information System (INIS)

2013-01-01

In 1985, the International Atomic Energy Agency (IAEA) published a report titled 'Status of Liquid Metal Cooled Fast Breeder Reactors' (Technical Reports Series No. 246). The report was a general review of the status of fast reactor development at that time, covering some aspects of design and operation and reviewing experience from the earliest days. It summarized the programmes and plans in all countries which were pursuing the development of fast reactors. In 1999, the IAEA published a follow-up report titled 'Status of Liquid Metal Cooled Fast Reactor Technology' (IAEA-TECDOC-1083), necessitated by the substantial advances in fast reactor technology development and changes in the economic and regulatory environment which took place during the period of 1985-1998. Chief among these were the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at a high burnup and the launch of new fast reactor programmes by some additional Member States. In 2006, the Technical Working Group on Fast Reactors (TWG-FR) identified the need to update its past publications and recommended the preparation of a new status report on fast reactor technology. The present status report intends to provide comprehensive and detailed information on the technology of fast neutron reactors. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction, operation and decommissioning; various areas of research and development; engineering; safety; and national strategies and public acceptance of fast reactors.

The status of work in the USSR on using inherent self-protection features of fast reactors, of passive and active means of shutdown and decay heat removal system

International Nuclear Information System (INIS)

Buksha, Yu.K.

1991-01-01

Extensive studies on fast reactor safety, aimed to increase intrinsic safety features and introduce passive safety means, are under way in the USSR. Design of the BN-800 reactor core with a close-to-zero sodium void effect of reactivity has been developed, complementary reactivity control means, based on passive principles are being implemented. As a whole, after the Chernobyl accident, the preference is given to the 'passive' full proof methods of safety. This approach may possibly seem excessive and may result in some losses concerning reactor economic characteristics

Fast reactors - Dounreay and the future

International Nuclear Information System (INIS)

Jordan, G.

1988-01-01

In 1960 at Dounreay, the Dounreay Fast Reactor (DFR) supplied the world's first fast reactor grid electricity, and went on to a highly successful career as a test facility, as fuel designs advanced. In the 1960s, the Prototype Fast Reactor (PFR) was designed and built, beginning operation in 1974. The PFR was built to provide a sound technical and experienced base to support the UK's future Fast Reactor development and design. The in-vessel fuel handling facilities have demonstrated the flexibility of the pool design and a considerable body of in-core fuel handling experience is available. A key issue for further Fast Reactor application is the performance of fuel and, because PFR was designed to take full-scale fuel assemblies, the fuel performance experience is directly relevant to commercial designs. The original PFR design irradiation target of 60000 MWd/t U (equivalent to 7.5 % burn-up) has already been exceeded by a factor of more than two and a 15.9 % burn-up sub-assembly has been discharged and reprocessed without difficulty. Soon a 20 % sub-assembly will follow. Also the PFR reprocessing plant has demonstrated the safety and efficiency of this essential adjunct to Fast Reactor operation. The safety and the environmental protection features of both the PFR and its fuel reprocessing plant have been demonstrated over the last 14 years. 2 refs., 3 figs

04 - Sodium cooled fast breeder fourth-generation reactors - The experimental reactor ALLEGRO, the other ways for fast breeder fourth-generation reactors

International Nuclear Information System (INIS)

2012-12-01

The authors first present the technology of gas-cooled fast breeder reactors (basic principles, specific innovations, feasibility studies, fuel element, safety) and notably the ALLEGRO project (design options and expected performances, preliminary safety demonstration). Then, they present the lead-cooled fast-breeder reactor technology: interests and obstacles, return on experience, the issue of lead density, neutron assessment, transmutation potential, dosimetry, safety chemical properties and compatibility with the fuel, water, air and steels. The next part addresses the technology of molten-salt fast-breeder reactors: choice of the liquid fuel and geometry, reactor concept (difficulties, lack of past R and D), demonstration and demonstrators, international context

Fast mixed spectrum reactor concept

International Nuclear Information System (INIS)

Kouts, H.J.C.; Fischer, G.J.; Cerbone, R.J.

1979-04-01

The Fast Mixed Spectrum Reactor is a highly promising concept for a fast reactor with improved features of proliferation resistance, and excellent utilization of uranium resources. In technology, it can be considered to be a branch of fast breeder development, though its operation and implications are different from those of FBR'S in important respects. Successful development programs are required in several areas to bring FMSR to reality, but the payoff from a successful program can be high

A review of the UK fast reactor programme. March 1977

International Nuclear Information System (INIS)

Smith, R.D.

1977-01-01

This paper reports on the Fast Reactor Programme of United Kingdom. These are the main lines: Dounreay Fast Reactor; Prototype Fast Reactor; Commercial Fast Reactor; engineering development; materials development; chemical engineering/sodium technology; fast reactor fuel; fuel cycle; safety; reactor performance study

Fast reactor fuel design and development

International Nuclear Information System (INIS)

Bishop, J.F.W.; Chamberlain, A.; Holmes, J.A.G.

1977-01-01

Fuel design parameters for oxide and carbide fast reactor fuels are reviewed in the context of minimising the total uranium demands for a combined thermal and fast reactor system. The major physical phenomena conditioning fast reactor fuel design, with a target of high burn-up, good breeding and reliable operation, are characterised. These include neutron induced void swelling, irradiation creep, pin failure modes, sub-assembly structural behaviour, behaviour of defect fuel, behaviour of alternative fuel forms. The salient considerations in the commercial scale fabrication and reprocessing of the fuels are reviewed, leading to the delineation of possible routes for the manufacture and reprocessing of Commercial Reactor fuel. From the desiderata and restraints arising from Surveys, Performance and Manufacture, the problems posed to the Designer are considered, and a narrow range of design alternatives is proposed. The paper concludes with a consideration of the development areas and the conceptual problems for fast reactors associated with those areas

Opening Address [International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios (FR13), Paris, France, March 4-7, 2013

International Nuclear Information System (INIS)

Amano, Yukiya

2013-01-01

Public confidence in nuclear power was greatly shaken by the Fukushima Daiichi accident. It will take time to rebuild that confidence. This will only be possible if everyone involved in nuclear power has a total commitment to safety and if the sector is open and transparent. The public need to be reassured that nuclear energy is efficient and safe, can mitigate the effects of climate change and can play a key role in meeting the growing global demand for energy. Fast reactors and related fuel cycles will be important for the long-term sustainability of nuclear power. This innovative technology has the potential to ensure that energy resources which would run out in a few hundred years, using today’s technology, will actually last several thousand years. Fast reactors also reduce the volume and toxicity of the final waste. China’s Experimental Fast Reactor has been connected to the grid. Work is at an advanced stage on construction of India’s 500 MW(e) Prototype Fast Breeder Reactor and of the large BN-800 reactor in the Russian Federation. Interest in fast reactors with closed fuel cycles is increasing steadily. A number of emerging economies are joining the existing fast reactor technology-holders. Considerable R & D work is being done on advanced designs with enhanced safety characteristics. It is important to gather the operational experience of countries with operating fast reactors and related fuel cycle facilities. This can help to achieve higher levels of safety. Events such as the Joint GIF-IAEA Workshop on the safety of sodium-cooled fast reactors last week are a useful way of doing this. They also help to ensure that relevant lessons from the Fukushima Daiichi accident are learned. The IAEA remains the unique collaboration forum for ensuring continued progress in fast reactor technology. We provide an umbrella for knowledge preservation, information exchange and collaborative R&D in which resources and expertise are pooled

The integral fast reactor

International Nuclear Information System (INIS)

Till, C.E.

1987-01-01

On April 3rd, 1986, two demonstrations of the inherent capability of sodium-cooled fast reactors to survive unprotected loss of cooling accidents were carried out on the experimental sodium-cooled power reactor, EBR-II, on the Idaho site of Argonne National Laboratory. Transients potentially of the most serious kind, one an unprotected loss of flow, the other an unprotected loss of heat sink, both initiated from full power. In both cases the reactor quietly shut itself down, without damage of any kind. These tests were a part of the on-going development program at Argonne to develop an advanced reactor with significant new inherent safety characteristics. Called the integral fast reactor, or IFR, the basic thrust is to develop everything that is needed for a complete nuclear power system - reactor, closed fuel cycle, and waste processing - as a single optimized entity, and, for simplicity in concept, as an integral part of a single plant. The particular selection of reactor materials emphasizes inherent safety characteristics also makes possible a simplified close fuel cycle and waste process improvements. The paper describes the IFR concept, the inherent safety, tests, and status of IFR development today

Decommissioning of fast reactors after sodium draining

International Nuclear Information System (INIS)

2009-11-01

Acknowledging the importance of passing on knowledge and experience, as well mentoring the next generation of scientists and engineers, and in response to expressed needs by Member States, the IAEA has undertaken concrete steps towards the implementation of a fast reactor data retrieval and knowledge preservation initiative. Decommissioning of fast reactors and other sodium bearing facilities is a domain in which considerable experience has been accumulated. Within the framework and drawing on the wide expertise of the Technical Working Group on Fast Reactors (TWG-FR), the IAEA has initiated activities aiming at preserving the feedback (lessons learned) from this experience and condensing those to technical recommendations on fast reactor design features that would ease their decommissioning. Following a recommendation by the TWG-FR, the IAEA had convened a topical Technical Meeting (TM) on 'Operational and Decommissioning Experience with Fast Reactors', hosted by CEA, Centre d'Etudes de Cadarache, France, from 11 to 15 March 2002 (IAEA-TECDOC- 1405). The participants in that TM exchanged detailed technical information on fast reactor operation and decommissioning experience with various sodium cooled fast reactors, and, in particular, reviewed the status of the various decommissioning programmes. The TM concluded that the decommissioning of fast reactors to reach safe enclosure presented no major difficulties, and that this had been accomplished mainly through judicious adaptation of processes and procedures implemented during the reactor operation phase, and the development of safe sodium waste treatment processes. However, the TM also concluded that, on the path to achieving total dismantling, challenges remain with regard to the decommissioning of components after sodium draining, and suggested that a follow-on TM be convened, that would provide a forum for in-depth scientific and technical exchange on this topic. This publication constitutes the Proceedings of

Fast-reactor fuel reprocessing in the United Kingdom

International Nuclear Information System (INIS)

Allardice, R.H.; Buck, C.; Williams, J.

1977-01-01

Enriched uranium metal fuel irradiated in the Dounreay Fast Reactor has been reprocessed and refabricated in plants specifically designed for the purpose in the United Kingdom since 1961. Efficient and reliable fuel recycle is essential to the development of a plutonium-based fast-reactor system, and the importance of establishing at an early stage fast-reactor fuel reprocessing has been reinforced by current world difficulties in reprocessing high-burnup thermal-reactor oxide fuel. The United Kingdom therefore decided to reprocess irradiated fuel from the 250MW(e) Prototype Fast Reactor (PFR) as an integral part of the fast reactor development programme. Flowsheet and equipment development work for the small-scale fully active demonstration plant has been carried out since 1972, and the plant will be commissioned and ready for active operation during 1977. In parallel, a comprehensive waste-management system has been developed and installed. Based on this development work and the information which will arise from active operation of the plant, a parallel development programme has been initiated to provide the basis for the design of a large-scale fast-reactor fuel-reprocessing plant to come into operation in the late 1980s to support the projected UK fast-reactor installation programme. The paper identifies the important differences between fast-reactor and thermal-reactor fuel-reprocessing technologies and describes some of the development work carried out in these areas for the small-scale PFR fuel-reprocessing operation. In addition, the development programme in aid of the design of a larger scale fast-reactor fuel-reprocessing plant is outlined and the current design philosophy discussed. (author)

History of fast reactor development in U.S.A.-I

International Nuclear Information System (INIS)

Ninokata, Hisashi; Sasao, Nobuyki

2007-01-01

History and present state of fast reactor was reviewed in series. As a history of fast reactor development in U.S.A. - I, this third lecture presented the dawn of the fast reactor development in the USA. The first fast reactor was the Clementine reactor with plutonium fuels and mercury coolant. The LAMPRE-1 reactor was the first sodium cooled and molten plutonium reactor. Experimental breeder reactor (EBR-1) was the first reactor to produce electricity and four kinds of fuels were loaded. Zero-power reactors were constructed to conduct reactor physics experiments on fast reactors. Today there are renewed interests in fast reactors due to their ability to fission actinides and reduce radioactive wastes. (T. Tanaka)

Fast Reactor Physics. Vol. II. Proceedings of a Symposium on Fast Reactor Physics and Related Safety Problems

International Nuclear Information System (INIS)

1968-01-01

Proceedings of a Symposium organized by the IAEA and held in Karlsruhe, 30 October - 3 November 1967. The meeting was attended by 183 scientists from 23 countries and three international organizations. Contents: (Vol.1) Review of national programmes (5 papers); Nuclear data for fast reactors (12 papers); Experimental methods (3 papers); Zoned systems (7 papers); Kinetics (7 papers). (Vol.11) Fast critical experiments (8 papers); Heterogeneity in fast critical experiments (5 papers); Fast power reactors (13 papers); Fast pulsed reactors (3 papers); Panel discussion. Each paper is in its original language (50 English, 11 French and 3 Russian) and is preceded by an abstract in English with a second one in the original language if this is not English. Discussions are in English. (author)

Fast reactors and problems in their development. Chapter 6

International Nuclear Information System (INIS)

Dombey, N.

1980-01-01

The main differences between fast reactors, in particular the liquid-metal fast breeder reactor (LMFBR), and thermal reactors are discussed. The view is taken, based on the intrinsic physics of the systems, that fast reactors should be considered as a different genus from thermal reactors. Some conclusions are drawn for fast reactor development generally and for the British programme in particular. Physics, economics and safety aspects are covered. (U.K.)

Euratom contributions in Fast Reactor research programmes

International Nuclear Information System (INIS)

Fanghänel, Th.; Somers, J.

2013-01-01

The Sustainable Nuclear Initiative: • demonstrate long-term sustainability of nuclear energy; • demonstration reactors of Gen IV: •more efficient use of resources; • closed fuel cycle; • reduced proliferation risks; • enhanced safety features. • Systems pursued in Europe: • Sodium-cooled fast reactor SFR; • Lead-cooled fast reactor LFR; • Gas-cooled fast reactor GFR. Sustainable Nuclear Energy Technology Platform SNE-TP promotes research, development and demonstration of the nuclear fission technologies necessary to achieve the SET-Plan goals

A review of the UK fast reactor programme

International Nuclear Information System (INIS)

Smith, R.D.

1982-01-01

A review of the United Kingdom Fast Reactor Programme is introduced. Operational experience with the Prototype Fast Reactor (PFR) is briefly summarized. The design concept of the Commercial Demonstration Fast Reactor (CDFR) is given in some detail. The emphasis is on materials development, chemical engineering/sodium technology, fuel reprocessing and fuel cycle, engineering component development and reactor safety

Status of national programmes on fast reactors 1997/98. 31. annual meeting of the International Working Group on Fast Reactors

International Nuclear Information System (INIS)

1998-01-01

The objective of the meeting was to co-ordinate the exchange of information on the status of fast reactor development and operational experience, including experience with experimental types of reactor; to consider meeting arrangements for 1998 and 1999; and to review the IAEA co-ordinated research activities in the field of fast reactor, as well as co-ordination of the International Working Group on Fast Reactors activities with other organizations

A review of the UK fast reactor programme

International Nuclear Information System (INIS)

Picker, C.; Ainsworth, K.F.

1998-01-01

The general position with regard to nuclear power and fast reactors in the UK during 1996 is described. The main UK Government-funded fast reactor research and development programme was concluded in 1993, to be replaced by a smaller programme which is mainly funded and managed by British Nuclear Fuels plc. The main focus of this programme sustains the UK participation in the European Fast Reactor (EFR) collaboration and the broader international links built-up over the previous decades. The status of fast reactor studies made in the UK in 1996 is outlined and, with respect to the Prototype Fast Reactor at Dounreay, a report of progress with the closure studies, fuel reprocessing and decommissioning activities is provided. (author)

The instrumentation of fast reactor

International Nuclear Information System (INIS)

Endo, Akira

2003-03-01

The author has been engaged in the development of fast reactors over the last 30 years with both an involvement with the early technology development on the experimental breeder reactor Joyo, and latterly continuing this work on the prototype breeder reactor, Monju. In order to pass on this experience to younger engineers this paper is produced to outline this experience in the sincere hope that the information given will be utilised in future educational training material. The paper discusses the wide diversity on the associated instrument technology which the fast breeder reactor requires. The first chapter outlines the fast reactor system, followed by discussions on reactor instrumentation, measurement principles, temperature dependencies, and verification response characteristics from various viewpoints, are discussed in chapters two and three. The important issues of failed fuel location detection, and sodium leak detection from steam generators are discussed in chapters 4 and 5 respectively. Appended to this report is an explanation on the methods of measuring response characteristics on instrumentation systems using error analysis, random signal theory and measuring method of response characteristic by AR (autoregressive) model on which it appears is becoming an indispensable problem for persons involved with this technology in the future. (author)

Fast Reactors and Nuclear Nonproliferation

International Nuclear Information System (INIS)

Avrorina, E.N.; Chebeskovb, A.N.

2013-01-01

Conclusion remarks: 1. Fast reactor start-up with U-Pu fuel: – dependent on thermal reactors, – no needs in U enrichment, – needs in SNF reprocessing, – Pu is a little suitable for NED, – practically impossible gun-type NED, – difficulties for implosion-type NED: necessary tests, advanced technologies, etc. – Pu in blankets is similar to WPu by isotopic composition, – Use of blanket for production isotopes (e.g. 233 U), – Combined reprocessing of SNF: altogether blanket and core, – Blanket elimination: decrease in Pu production – No pure Pu separation. 2. Fast reactor start-up with U fuel: - Needs in both U enrichment and SNF reprocessing, - Independent of thermal reactors, - Good Pu bred in the core let alone blankets, - NED of simple gun-type design, - Increase of needs in SWU, - Increased demands in U supply. 3. Fast reactors for export: - Uranium shortage, - To replace thermal reactors in future, - No blankets (depends on the country, though), - Fuel supply and SNF take back, - International centers for rendering services of NFC. Time has come to remove from FRs and their NFC the label unfairly identifying them as the most dangerous installations of nuclear power from the standpoint of being a proliferation problem

The safety of the fast reactor

International Nuclear Information System (INIS)

Matthews, R.R.

1977-01-01

Verbatim of an address by R.R. Matthews, Chief Nuclear Health and Safety Officer, UK Central Electricity Generating Board given on January 15th 1977. The object of this address was to give some opinions on the safety issues of fast reactors as seen from an operational point of view. An outline of the basic responsibilities for nuclear safety is first given, and it is emphasized that the Central Electricity Generating Board has a statutory responsibility for the safe operation of its nuclear plant. The Nuclear Installations Act places absolute responsibility on the operator for ensuring that injury to persons and damage to property do not occur, and the new Health and Safety at Work Act does likewise. In addition the Board has a Nuclear Health and Safety Department that has to ensure that adequate provision for safety is made in the design, construction, and operation of nuclear plant, and safety at operational stations is monitored continuously by inspectors. In addition the requirements of the Nuclear Installations Inspectorate, laid down in the site licence conditions, must be satisfied. All these requirements are here discussed in the light of application to commercial fast reactors. It is considered that the hazards to fast reactor operating personnel are small and little different from those of other types of reactor, and in some respects the fast reactor has advantages, particularly in regard to the use of a Na coolant. The possibility of various types of accident is considered. Radioactive effluent discharge is also considered. The fast reactor as an international problem is discussed, including security matters. The extensive experience gained in operation of the experimental and prototype fast reactors at Dounreay is emphasized. (U.K.)

Status of liquid metal cooled fast reactor technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

During the period 1985-1998, there have been substantial advances in fast reactor technology development. Chief among these has been the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at high burnup. At the IAEA meetings on liquid metal cooled fast reactor technology (LMFR), it became evident that there have been significant technological advances as well as changes in the economic and regulatory environment since 1985. Therefore the International working group on Fast Reactors has recommended the preparation of a new status report on fast reactors. The present report intends to provide comprehensive and detailed information on LMFR technology. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction and operation, reactor physics and safety, sore structural material and fuel technology, fast reactor engineering and activities in progress on LMFR plants Refs, figs, tabs

Status of liquid metal cooled fast reactor technology

International Nuclear Information System (INIS)

1999-04-01

During the period 1985-1998, there have been substantial advances in fast reactor technology development. Chief among these has been the demonstration of reliable operation by several prototypes and experimental reactors, the reliable operation of fuel at high burnup. At the IAEA meetings on liquid metal cooled fast reactor technology (LMFR), it became evident that there have been significant technological advances as well as changes in the economic and regulatory environment since 1985. Therefore the International working group on Fast Reactors has recommended the preparation of a new status report on fast reactors. The present report intends to provide comprehensive and detailed information on LMFR technology. The focus is on practical issues that are useful to engineers, scientists, managers, university students and professors, on the following topics: experience in construction and operation, reactor physics and safety, sore structural material and fuel technology, fast reactor engineering and activities in progress on LMFR plants

Fast reactor database

International Nuclear Information System (INIS)

1996-02-01

This publication contains detailed data on liquid metal cooled fast reactors (LMFRs), specifically plant parameters and design details. Each LMFR power plant is characterized by about 400 parameters, by design data and by relevant materials. The report provides general and detailed design characteristics including structural materials, data on experimental, demonstration, prototype and commercial size LMFRs. The focus is on practical issues that are useful to engineers, scientists, managers and university students and professors. The report includes updated information contained in IAEA previous publications on LMFR plant parameters: IWGRF/51 (1985) and IWGFR/80 (1991) and reflects experience gained from two consultants meetings held in Vienna (1993,1994). This compilation of data was produced by members of the IAEA International Working Group on Fast Reactors (IWGFR)

Seminar on Heat-transfer fluids for fast neutron reactors

International Nuclear Information System (INIS)

Brechet, Yves; Dautray, Robert; Friedel, Jacques; Brezin, Edouard; Martin, Georges; Pineau, Andre; Carre, Francois; Gauche, Francois; Rodriguez, Guillaume; Latge, Christian; Cabet, Celine; Garnier, Jean-Claude; Bamberger, Yves; Sauvage, Jean-Francois; Buisine, Denis; Agostini, Pietro; Ulyanov, Vladimir; Auger, Thierry; Heuer, Daniel; Ghetta, Veronique; Bubelis, Evaldas; Charlaix, Elisabeth; Barrat, Jean-Louis; Boquet, Lyderic; Glickman, Evgueny; Escaravage, Claude

2014-03-01

This book reports the content of a two-day meeting held by the Academy of Sciences on the use of heat-transfer fluids in fast neutron reactors. After a first part which proposes an overview of scientific and technical problems related to these heat-transfer fluids (heat transfer process, nuclear properties, chemistry, materials, risks), a contribution proposes a return on experience on the use of heat-transfer fluids in the different design options of reactors of fourth generation: from mercury to NaK in the first fast neutron reactor projects, specific assets and constraints of sodium used as heat-transfer fluid, concepts of fast neutron reactors cooled by something else than sodium, perspectives for projects and research in fast neutron reactors. The next contribution discusses the specifications of future fast-neutron reactors: expectations for fourth-generation reactors, expectations in terms of performance and of safety, specific challenges. The last contribution addresses actions to be undertaken in the field of research and development: actions regarding all reactor types or specific types as sodium-cooled reactors, lead cooled reactors, molten salt reactors, and gas-cooled fast reactors

Review of fast reactor activities

International Nuclear Information System (INIS)

Haeussermann, W.; Royen, J.

1978-01-01

Since 1971, when the Co-ordinating Group on Gas-Cooled Fast reactors Development was set up, the participating countries have maintained an interest in keeping this option as a back-up solution to the sodium cooled fast reactors. Two different concepts were investigated, one based on coated particle type fuel elements and the other on pin type fuel elements. The coated particles studies have been brought to an end, and resources were concentrated on the further development of the pin type concept. The work done in previous years covered design and safety investigations, heat transfer studies and irradiation experiments in thermal reactors

Economic evaluation of fast reactor fuel cycling

International Nuclear Information System (INIS)

Hu Ping; Zhao Fuyu; Yan Zhou; Li Chong

2012-01-01

Economic calculation and analysis of two kinds of nuclear fuel cycle are conducted by check off method, based on the nuclear fuel cycling process and model for fast reactor power plant, and comparison is carried out for the economy of fast reactor fuel cycle and PWR once-through fuel cycle. Calculated based on the current price level, the economy of PWR one-through fuel cycle is better than that of the fast reactor fuel cycle. However, in the long term considering the rising of the natural uranium's price and the development of the post treatment technology for nuclear fuels, the cost of the fast reactor fuel cycle is expected to match or lower than that of the PWR once-through fuel cycle. (authors)

A review of the UK fast reactor programme

International Nuclear Information System (INIS)

Picker, C.; Ainsworth, K.F.

1996-01-01

The general position with regard to nuclear power and fast reactors in UK during 1995 is described. The status of fast reactor studies made in UK is outlined and a description and statement regarding the conclusions of the programme of studies associated with the closure of the Prototype Fast Reactor is included. (author)

A review of the UK fast reactor programme

Energy Technology Data Exchange (ETDEWEB)

Picker, C [AEA Technolgy plc, Risley, Warrington, Cheshire (United Kingdom); Ainsworth, K F [British Nuclear Fuels plc, Sellafield, Cumbria (United Kingdom)

1996-07-01

The general position with regard to nuclear power and fast reactors in UK during 1995 is described. The status of fast reactor studies made in UK is outlined and a description and statement regarding the conclusions of the programme of studies associated with the closure of the Prototype Fast Reactor is included. (author)

Fast reactor knowledge preservation system: Taxonomy and basic requirements

International Nuclear Information System (INIS)

2008-01-01

The IAEA has taken the initiative to coordinate efforts of Member States in the preservation of knowledge in the area of fast reactors. In the framework of this initiative, the IAEA intends to create an international database compiling information from different Member States on fast reactors through a web portal. Other activities related to this initiative are being designed to accumulate and exchange information on the fast reactor area, to facilitate access to this information by users in different countries and to assist Member States in preserving the experience gained in their countries. The purpose of this publication is to develop a taxonomy of the Fast Reactor Knowledge Preservation System (FRKPS) that will facilitate the preservation of the world's fast reactor knowledge base, to identify basic requirements of this taxonomy on the basis of the experience gained in the fast reactor area, as well as results of previous IAEA activities on fast reactor knowledge preservation. The need for such taxonomy arises from the fact that during the past 15 years there has been stagnation in the development of fast reactors in the industrialized countries that were involved, earlier, in intensive development of this area. All studies on fast reactors have been stopped in countries such as Germany, Italy, the United Kingdom and the United States of America and the only work being carried out is related to the decommissioning of fast reactors. Many specialists who were involved in the studies and development work in this area in these countries have already retired or are close to retirement. In countries such as France, Japan and the Russian Federation that are still actively pursuing the evolution of fast reactor technology, the situation is aggravated by the lack of young scientists and engineers moving into this branch of nuclear power

Concept and basic performance of an in-pile experimental reactor for fast breeder reactors using fast driver core

International Nuclear Information System (INIS)

Obara, Toru; Sekimoto, Hiroshi

1997-01-01

The possibility of an in-pile experimental reactor for fast breeder reactors using a fast driver core is investigated. The driver core is composed of a particle bed with diluted fuel. The results of various basic analyses show that this reactor could perform as follows: (1) power peaking at the outer boundary of test core does not take place for large test core; (2) the radial power distribution in test fuel pin is expected to be the same as a real reactor; (3) the experiments with short half width pulse is possible; (4) for the ordinary MOX core, enough heating-up is possible for core damage experiments; (5) the positive effects after power burst can be seen directly. These are difficult for conventional thermal in-pile experimental reactors in large power excursion experiments. They are very attractive advantages in the in-pile experiments for fast breeder reactors. (author)

Review of fast reactor activities in India

Energy Technology Data Exchange (ETDEWEB)

Paranjpe, S R [Reactor Research Centre, Kalpakkam, Tamil Nadu (India)

1981-05-01

It may be recalled that In the presentation at the last meeting of the IWGFR (13th Annual meeting), a broad outline of India's nuclear energy programme and the role of fast breeders in the programme has been provided. The steps taken to enable the fast breeders to fulfil their role have also been described. In brief, fast breeder reactors are considered as an essential and integral part of the programme of nuclear energy and constitute the second step in the programme, the first being the construction of natural uranium heavy water moderated reactors which will consume natural uranium but will produce plutonium to fuel fast breeder reactors. This basic position has remained unchanged and the Government is now taking steps to build a large number of heavy water reactors, say 10 million Kw capacity in the next 20 years. This defines the time frame for developing the fast breeder technology in the country. It has therefore been decided to mobilise the efforts towards design, construction and operation of a medium sized (about 500 M We) reactor by mid-nineties. Thus, the climate for fast breeder reactors is good and there is a good deal of enthusiasm amongst the scientists and engineers working in the field although the actual implementation of the programme during the year had to face certain difficulties.

Review of fast reactor activities in India

International Nuclear Information System (INIS)

Paranjpe, S.R.

1981-01-01

It may be recalled that In the presentation at the last meeting of the IWGFR (13th Annual meeting), a broad outline of India's nuclear energy programme and the role of fast breeders in the programme has been provided. The steps taken to enable the fast breeders to fulfil their role have also been described. In brief, fast breeder reactors are considered as an essential and integral part of the programme of nuclear energy and constitute the second step in the programme, the first being the construction of natural uranium heavy water moderated reactors which will consume natural uranium but will produce plutonium to fuel fast breeder reactors. This basic position has remained unchanged and the Government is now taking steps to build a large number of heavy water reactors, say 10 million Kw capacity in the next 20 years. This defines the time frame for developing the fast breeder technology in the country. It has therefore been decided to mobilise the efforts towards design, construction and operation of a medium sized (about 500 M We) reactor by mid-nineties. Thus, the climate for fast breeder reactors is good and there is a good deal of enthusiasm amongst the scientists and engineers working in the field although the actual implementation of the programme during the year had to face certain difficulties

Review of fast reactor activities

International Nuclear Information System (INIS)

1982-01-01

A description of some highlights of the activities performed by the Commission of the European Communities in the field of fast reactors is given. They fall into two categories: coordinating and harmonizing activities and research activities. The former are essentially performed in the frame of the Fast Reactor Coordinating Committee (FRCC), the latter in the Commission's Joint Research Center and to some extent under contract in research centers of the Member States

International Experience with Fast Reactor Operation & Testing

International Nuclear Information System (INIS)

Sackett, John I.; Grandy, C.

2013-01-01

Conclusion: • Worldwide experience with fast reactors has demonstrated the robustness of the technology and it stands ready for worldwide deployment. • The lessons learned are many and there is danger that what has been learned will be forgotten given that there is little activity in fast reactor development at the present time. • For this reason it is essential that knowledge of fast reactor technology be preserved, an activity supported in the U.S. as well as other countries

Fast reactor development programme in France

Energy Technology Data Exchange (ETDEWEB)

Le Rigoleur, C [Direction des Reacteurs Nucleaires, CEA Centre d` Etudes de Cadarache, Saint-Paul-lez-Durance (France)

1998-04-01

First the general situation regarding production of electricity in France is briefly described. Then in the field of Fast Reactors, the main events of 1996 are presented. At the end of February 1996, the PHENIX reactor was ready for operation. After review meetings, the Safety Authority has requested safety improvements and technical demonstrations, before it examines the possibility of authorizing a new start-up of PHENIX. The year 1996 was devoted to this work. In 1996, SUPERPHENIX was characterized by excellent operation throughout the year. The reactor was restarted at the end of 1995 after a number of minor incidents. The reactor power was increased by successive steps: 30% Pn up to February 6, followed by 50% Pn up to May then 60% up to October and 90% Pn during the last months. A programmed shutdown period occurred during May, June and mid-July 1996. The reactor has been shutdown at the end of 1996 for the decenial control of the steam generators. The status of the CAPRA project, aimed at demonstrating the feasibility of a fast reactor to burn plutonium at as high a rate as possible and the status of the European Fast Reactor are presented as well as their evolution. Finally the R and D in support of the operation of PHENIX and SUPERPHENIX, in support of the ````knowledge-acquisition```` programme, and CAPRA and EFR programmes is presented, as well as the present status of the stage 2 dismantling of the RAPSODIE experimental fast reactor. (author). 4 refs, figs, 2 tabs.

Gas-cooled fast breeder reactor

International Nuclear Information System (INIS)

Yoshida, Hiroyuki

1982-07-01

Almost all the R D works of gas-cooled fast breeder reactor in the world were terminated at the end of the year 1980. In order to show that the R D termination was not due to technical difficulties of the reactor itself, the present paper describes the reactor plant concept, reactor performances, safety, economics and fuel cycle characteristics of the reactor, and also describes the reactor technologies developed so far, technological problems remained to be solved and planned development schedules of the reactor. (author)

The Integral Fast Reactor

International Nuclear Information System (INIS)

Chang, Y.I.

1988-01-01

The Integral Fast Reactor (IFR) is an innovative liquid metal reactor concept being developed at Argonne National Laboratory. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system. This paper describes the key features and potential advantages of the IFR concept, with emphasis on its safety characteristics. 3 refs., 4 figs., 1 tab

A small modular fast reactor as starting point for industrial deployment of fast reactors

International Nuclear Information System (INIS)

Chang, Yoon I.; Lo Pinto, Pierre; Konomura, Mamoru

2006-01-01

The current commercial reactors based on light water technology provide 17% of the electricity worldwide owing to their reliability, safety and competitive economics. In the near term, next generation reactors are expected to be evolutionary type, taking benefits of extensive LWR experience feedbacks and further improved economics and safety provisions. For the long term, however, sustainable energy production will be required due to continuous increase of the human activities, environmental concerns such as greenhouse effect and the need of alternatives to fossil fuels as long term energy resources. Therefore, future generation commercial reactors should meet some criteria of sustainability that the current generation cannot fully satisfy. In addition to the current objectives of economics and safety, waste management, resource extension and public acceptance become other major objectives among the sustainability criteria. From this perspective, two questions can be raised: what reactor type can meet the sustainability criteria, and how to proceed to an effective deployment in harmony with the high reliability and availability of the current nuclear reactor fleet. There seems to be an international consensus that the fast spectrum reactor, notably the sodium-cooled system is most promising to meet all of the long term sustainability criteria. As for the latter, we propose a small modular fast reactor project could become a base to prepare the industrial infrastructure. The paper has the following contents: - Introduction; - SMFR project; - Core design; - Supercritical CO 2 Brayton cycle; - Near-term reference plant; - Advanced designs; - Conclusions. To summarize, the sodium-cooled fast reactor is currently recognized as the technology of choice for the long term nuclear energy expansion, but some research and development are required to optimize and validate advanced design solutions. A small modular fast reactor can satisfy some existing near-term market niche

Strategies for minority actinides transmutation in fast reactors

International Nuclear Information System (INIS)

Perez-Martin, S.; Martin-Fuertes, F.; Alvarez-Velarde, F.

2010-01-01

Presentation of the strategies that can be followed in fast reactors designed for the fourth generation to reduce the inventory of minority actinides generated in current light water reactors, as the actinides generation in fast reactor.

Prototype fast breeder reactor main options

International Nuclear Information System (INIS)

Bhoje, S.B.; Chellapandi, P.

1996-01-01

Fast reactor programme gets importance in the Indian energy market because of continuous growing demand of electricity and resources limited to only coal and FBR. India started its fast reactor programme with the construction of 40 MWt Fast Breeder Test Reactor (FBTR). The reactor attained its first criticality in October 1985. The reactor power will be raised to 40 MWt in near future. As a logical follow-up of FBTR, it was decided to build a prototype fast breeder reactor, PFBR. Considering significant effects of capital cost and construction period on economy, systematic efforts are made to reduce the same. The number of primary and secondary sodium loops and components have been reduced. Sodium coolant, pool type concept, oxide fuel, 20% CW D9, SS 316 LN and modified 9Cr-1Mo steel (T91) materials have been selected for PFBR. Based on the operating experience, the integrity of the high temperature components including fuel and cost optimization aspects, the plant temperatures are recommended. Steam temperature of 763 K at 16.6 MPa and a single TG of 500 MWe gross output have been decided. PFBR will be located at Kalpakkam site on the coast of Bay of Bengal. The plant life is designed for 30 y and 75% load factor. In this paper the justifications for the main options chosen are given in brief. (author). 2 figs, 2 tabs

Fast breeder reactor safety : a perspective

International Nuclear Information System (INIS)

Kale, R.D.

1992-01-01

Taking into consideration India's limited reserves of natural and vast reserves of thorium, the fast reactor route holds a great promise for India's energy supply in future. The fast reactor fueled with 239 Pu/ 238 U (unused or depleted) produces (breeds) more fissionable fuel material 239 Pu than it consumes. Calculations show that a fast breeder reactor (FBR) increases energy potential of natural uranium by about 60 times. As the fast reactor can also convert 232 Th into 233 U which is a fissionable material, it can make India's thorium reserves a source of almost inexhaustible energy supply for a long time to come. Significant advantage of FBR plants cooled by sodium and their world-wide operating experience are reviewed. There are two main safety issues of FBR, one nuclear and the other non-nuclear. The nuclear issue concerns core disruptive accident and the non-nuclear one concerns the high chemical energy potential of sodium. These two issues are analysed and it is pointed that they are manageable by current design, construction and operational practices. Main findings of safety research during the last six to eight years in West European Countries and United States of America (US) are summarised. Three stage engineered safety provision incorporated into the design of the sodium cooled Fast Breeder Test Reactor (FBTR) commissioned at Kalpakkam are explained. The important design safety features of FBTR such as primary system containment, emergency core cooling, plant protection system, inherent safety features achieved through reactivity coefficients, and natural convection cooling are discussed. Theoretical analysis and experimental research in fast reactor safety carried out at the Indira Gandhi Centre for Atomic Research during the past some years are reviewed. (M.G.B.)

What is the future for fast reactor technology?

International Nuclear Information System (INIS)

Kraev, Kamen

2017-01-01

NucNet spoke to Vladimir Kriventsev, team leader for fast reactor technology development at the International Atomic Energy Agency (IAEA), about the possibilities and challenges of technology development in the fast reactor sector. Today, the field of fast reactors is vibrant and full of fascinating developments, some which will have an impact in the nearer term and others in the longer term.

What is the future for fast reactor technology?

Energy Technology Data Exchange (ETDEWEB)

Kraev, Kamen [NucNet, Brussels (Belgium). The Independent Global Nuclear News Agency

2017-08-15

NucNet spoke to Vladimir Kriventsev, team leader for fast reactor technology development at the International Atomic Energy Agency (IAEA), about the possibilities and challenges of technology development in the fast reactor sector. Today, the field of fast reactors is vibrant and full of fascinating developments, some which will have an impact in the nearer term and others in the longer term.

Statement to International Conference on Fast Reactors and Related Fuel Cycles: Challenges and Opportunities, 7 December 2009, Kyoto, Japan

International Nuclear Information System (INIS)

Amano, Yukiya

2009-01-01

Full text: Distinguished Guests, Ladies and Gentlemen, It is my honour to address participants at this opening session of the International Conference on Fast Reactors and Related Fuel Cycles: Challenges and Opportunities, organized by the IAEA and hosted by the Japan Atomic Energy Agency. Fast reactor technology has the potential to ensure that energy resources which would last hundreds of years with the technology we are using today will actually last several thousand years. In other words it can withstand enormous increases in demand. This innovative technology also reduces the risk to the environment and helps to limit the burden that will be placed on future generations in the form of waste products. The coming year will be an exciting one for the development of fast-spectrum nuclear reactors. We expect to reach many important milestones: - the first criticality of the China Experimental Fast Reactor; - the restart of the Monju prototype fast reactor in Japan; and - the new insights we will gain through the end-of-life studies at the Phenix reactor in France. In the near future, new fast reactors will be commissioned: the 500MW(e) Prototype Fast Breeder Reactor in India, the first in a series of five of the same type, and the BN-800 reactor in the Russian Federation. Moreover, France, Japan, India, China and the Republic of Korea are preparing advanced prototypes, demonstration or commercial reactors for the 2020-2030 period. Nuclear power is set to be an increasingly important part of the global energy mix in the coming decades as demand for energy grows. Scores of countries in both the developed and developing world have told the IAEA that they are interested in introducing nuclear power. The 30 countries which already have nuclear power reactors are set to build more. This trend is likely to be accompanied by accelerated deployment of fast reactors. Continued advances in research and technology development are necessary to ensure improved economics and

Advances by the Integral Fast Reactor Program

International Nuclear Information System (INIS)

Lineberry, M.J.; Pedersen, D.R.; Walters, L.C.; Cahalan, J.E.

1991-01-01

The advances by the Integral Fast Reactor Program at Argonne National Laboratory are the subject of this paper. The Integral Fast Reactor (IFR) is an advanced liquid-metal-cooled reactor concept being developed at Argonne National Laboratory. The advances stressed in the paper include fuel irradiation performance, improved passive safety, and the development of a prototype fuel cycle facility. 14 refs

Actinides burnup in a sodium fast reactor

Energy Technology Data Exchange (ETDEWEB)

Ramirez S, J. R.; Pineda A, R.; Martinez C, E.; Alonso, G., E-mail: ramon.ramirez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2017-09-15

The burnup of actinides in a nuclear reactor is been proposed as part of an advanced nuclear fuel cycle, this process would close the fuel cycle recycling some of the radioactive material produced in the open nuclear fuel cycle. These actinides are found in the spent nuclear fuel from nuclear power reactors at the end of their burnup in the reactor. Previous studies of actinides recycling in thermal reactors show that would be possible reduce the amounts of actinides at least in 50% of the recycled amounts. in this work, the amounts of actinides that can be burned in a fast reactor is calculated, very interesting results surge from the calculations, first, the amounts of actinides generated by the fuel is higher than for thermal fuel and the composition of the actinides vector is different as in fuel for thermal reactor the main isotope is the {sup 237}Np in the fuel for fast reactor the main isotope is the {sup 241}Am, finally it is concluded that the fast reactor, also generates important amounts of waste. (Author)

Some questions and answers concerning fast reactors

International Nuclear Information System (INIS)

Marshall, W.

1980-01-01

The theme of the lecture is the place of the fast reactor in an evolving nuclear programme. The whole question of plutonium is first considered, ie its method of production and the ways in which it can be used in the fast reactor fuel cycle. Whether fast reactors are necessary is then discussed. Their safety is examined with particular attention to those design features which are most criticised ie high volumetric power density of the core, and the use of liquid sodium as coolant. Attention is then paid to environmental and safeguard aspects. (U.K.)

Monte Carlo transport correction of sodium reactivity worth spatial distribution in perspective Sodium-Cooled Fast Reactor

International Nuclear Information System (INIS)

Raskach, K.F.; Blyskavka, V; Kislitsyna, T.S.

2011-01-01

In this paper we apply Monte Carlo for calculating spatial distribution of sodium reactivity worth in the perspective Russian sodium-cooled fast reactor BN-1200. A special Monte Carlo technique applicable for calculating perturbations and derivatives of the effective multiplication factor is used. The numerical results obtained show that Monte Carlo has a good perspective to deal with such problems and to be used as a reference solution for engineering codes based on the diffusion approximation. They also allow to conclude that in the sodium blanket and in the neighboring region of the core the diffusion code used likely overestimates sodium reactivity worth. This conclusion has to be verified in future work. (author)

Settlement substantiation of the passive devices shutdown fast reactors by trip the absorbing rod in case of anticipated accident

International Nuclear Information System (INIS)

Portianoy, A.G.; Serdun, E.N.; Sorokin, A.P.; Uhov, V.A.; Egorov, V.S.

2000-01-01

Results of improvement of the passive device shutdown fast reactors BN-600 (PDSR) are considered. The device works (lets off a neutron absorber) at increase of coolant temperature above 660 deg. C (650 deg. C). The PDSR working element represents a design of a sylphon-container type, filled with aluminium (magnesium) and operates (extended) under melting it at the expense of energy of a compressed high-temperature spring, and/or increases of a volume (6% of aluminium) at melting, and/or increases of a volume at further growth of a temperature. Account of the characteristics of PDSR working elements is carried out. Mathematical models, describing dependence of the basic of the characteristics (sluggishness, size of lengthening) from the constructive factors and modes of anticipated accident, are received. Is shown, that the PDSR characteristics provide an emergency stop of the reactor BN-600 in a case of a heaviest anticipated accident prior to the beginning sodium boiling in a core. The developed PDSR have a number of advantages before known, for example, magnetic with a Curie point, first of all, at the expense of significant efforts generation, multichannels of operation and weak dependence on the operational factors, first of all, neutron fluence. (author)

A review of the U.K. fast reactor programme: March 1978

Energy Technology Data Exchange (ETDEWEB)

Smith, R D [United Kingdom Atomic Energy Authority, Risley (United Kingdom)

1978-07-01

The review of the UK fast reactor programme covers the description of Dounreay Fast Reactor shut down after seventeen years of successful operation; description of prototype fast reactor (PFR); core design parameters safety features and plant design for commercial demonstration fast reactor (CDFR). Engineering development is related to large sodium rigs, coolant circuit hydraulics and vibration, instrumentation and components. The subjects of interest are material development, sodium technology, fast reactor fuel, fuel cycle, reactor safety, reactor performance studies.

A review of the U.K. fast reactor programme: March 1978

International Nuclear Information System (INIS)

Smith, R.D.

1978-01-01

The review of the UK fast reactor programme covers the description of Dounreay Fast Reactor shut down after seventeen years of successful operation; description of prototype fast reactor (PFR); core design parameters safety features and plant design for commercial demonstration fast reactor (CDFR). Engineering development is related to large sodium rigs, coolant circuit hydraulics and vibration, instrumentation and components. The subjects of interest are material development, sodium technology, fast reactor fuel, fuel cycle, reactor safety, reactor performance studies

Review of fast reactor activities

Energy Technology Data Exchange (ETDEWEB)

Balz, W [Commission of the European Communities, Brussels (Belgium)

1978-07-01

The Commission of the European Communities continued its activities on the following lines: activities aimed at preparing for commercialization of fast breeder reactors which are essentially performed in the frame of Fast Reactor Coordinating Committee (FRCC); the execution of its own research program in the Joint Research Center. The report covers activities of the FRCC, of the Safety Working Group (SWG), the Whole Core Accident Code (WAC) subgroup, Containment (CONT) subgroup, Codes and Standards Working Group (CSWG). Research and development activities are concerned with LMFBR safety, subassembly thermal hydraulics, fuel-coolant interactions, post-accident heat removal, dynamic load response, safety related material properties, utilization limits of fast breeder fuels, plutonium and actinide aspects of nuclear fuel cycle.

Review of fast reactor activities

International Nuclear Information System (INIS)

Balz, W.

1978-01-01

The Commission of the European Communities continued its activities on the following lines: activities aimed at preparing for commercialization of fast breeder reactors which are essentially performed in the frame of Fast Reactor Coordinating Committee (FRCC); the execution of its own research program in the Joint Research Center. The report covers activities of the FRCC, of the Safety Working Group (SWG), the Whole Core Accident Code (WAC) subgroup, Containment (CONT) subgroup, Codes and Standards Working Group (CSWG). Research and development activities are concerned with LMFBR safety, subassembly thermal hydraulics, fuel-coolant interactions, post-accident heat removal, dynamic load response, safety related material properties, utilization limits of fast breeder fuels, plutonium and actinide aspects of nuclear fuel cycle

Review of fast reactor activities at OECD (NEA)

International Nuclear Information System (INIS)

Stephens, M.

1981-01-01

The Committee on the Safety of Nuclear Installations initiated several reports in 1979. Status reports are published on: the role of fission gas release in case of fuel element failure; reactivity monitoring in a LMFBR at shutdown; increasing the reliability of fast reactor shutdown systems. A report is planned on the interactions between sodium and concrete. LMFBR safety issue that were studied are concerned with containment R and D; natural circulation cooling; and fuel failure modelling. Nuclear Development Division was concerned with Gas cooled fast reactors technology. Nuclear Science Division dealt with fast reactor physics and nuclear data for fast reactors. NEA Data Bank provides technical support and acts as a computer code library and nuclear data centre

Review of fast reactor activities in India (1982-83)

International Nuclear Information System (INIS)

Paranjpe, S.R.

1983-01-01

A review of fast reactor activities in India in 1982-1983 is given. One stage of construction of Fast Breeder Test Reactor (FBTR) is briefly described. The emphasis is on design studies for the 500 MWe Prototype Fast Breeder Reactor (PFBR). The main features of this design are introduced

Current status and perspective of advanced loop type fast reactor in fast reactor cycle technology development project

International Nuclear Information System (INIS)

Niwa, Hajime; Aoto, Kazumi; Morishita, Masaki

2007-01-01

After selecting the combination of the sodium-cooled fast reactor (SFR) with oxide fuel, the advanced aqueous reprocessing and the simplified pelletizing fuel fabrication as the most promising concept of FR cycle system, 'Feasibility Study on Commercialized Fast Reactor Cycle Systems' was finalized in 2006. Instead, a new project, Fast Reactor Cycle Technology Development Project (FaCT Project) was launched in Japan focusing on development of the selected concepts. This paper describes the current status and perspective of the advanced loop type SFR system in the FaCT Project, especially on the design requirements, current design as well as the related innovative technologies together with the development road-map. Some considerations on advantages of the advanced loop type design are also described. (authors)

Main research results in the field of nuclear power engineering of the Nuclear Reactors and Thermal Physics Institute in 2014

International Nuclear Information System (INIS)

Trufanov, A.A.; Orlov, Yu.I.; Sorokin, A.P.; Chernonog, V.L.

2015-01-01

The main results of scientific and technological activities for last years of the Nuclear Reactors and Thermal Physics Institute FSUE SSC RF - IPPE in solving problems of nuclear power engineering are presented. The work have been carried out on the following problems: justification of research and development solutions and safety of NPPs with fast reactors of new generation with sodium (BN-1200, MBIR) and lead (BREST-OD-300) coolants, justification of safety of operating and advanced NPPs with WWER reactor facilities (WWER-1000, AEhS 2006, WWER-TOI), development and benchmarking of computational codes, research and development support of Beloyarsk-3 (BN-600) and Bilibino (BN-800) NPPs operation, decommissioning of AM and BR-10 research reactors, pilot scientific studies (WWER-SKD, ITER), international scientific and technical cooperation. Problems for further investigations are charted [ru

The Integral Fast Reactor

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.; Lineberry, M.J.

1990-01-01

Argonne National Laboratory, since 1984, has been developing the Integral Fast Reactor (IFR). This paper will describe the way in which this new reactor concept came about; the technical, public acceptance, and environmental issues that are addressed by the IFR; the technical progress that has been made; and our expectations for this program in the near term. 5 refs., 3 figs

Sodium fast reactors with closed fuel cycle

CERN Document Server

Raj, Baldev; Vasudeva Rao, PR 0

2015-01-01

Sodium Fast Reactors with Closed Fuel Cycle delivers a detailed discussion of an important technology that is being harnessed for commercial energy production in many parts of the world. Presenting the state of the art of sodium-cooled fast reactors with closed fuel cycles, this book:Offers in-depth coverage of reactor physics, materials, design, safety analysis, validations, engineering, construction, and commissioning aspectsFeatures a special chapter on allied sciences to highlight advanced reactor core materials, specialized manufacturing technologies, chemical sensors, in-service inspecti

Analytical and Experimental Study for Validation of the Device to Confine BN Reactor Melted Fuel

International Nuclear Information System (INIS)

Rogozhkin, S.; Osipov, S.; Sobolev, V.; Shepelev, S.; Kozhaev, A.; Mavrin, M.; Ryabov, A.

2013-01-01

To validate the design and confirm the design characteristics of the special retaining device (core catcher) used for protection of BN reactor vessel in the case of a severe beyond-design basis accident with core melting, computational and experimental studies were carried out. The Tray test facility that uses water as coolant was developed and fabricated by OKBM; experimental studies were performed. To verify the methodical approach used for the computational study, experimental results obtained in the Tray test facility were compared with numerical simulation results obtained by the STAR-CCM+ CFD code

Cleaning of the equipment of residual sodium by means of water-vacuum technology

International Nuclear Information System (INIS)

Klykov, B.P.; Lednev, A.I.

1997-01-01

Results of investigation into a problem of equipment decontamination from sodium, that have been conducted in OKBM since 1960 are given. The investigations performed have shown that a water-vacuum washing process is the most optimal method for equipment decontamination from sodium residues. The essence of the method is in conduction of sodium-water reaction under reduced pressure in a leak-tight tank. Boundary conditions are selected experimentally which not allow sodium to be melted during the process, that gives possibility to control the sodium-water reaction. Continuous removal of H 2 and reaction products creates safe conditions for the process conduction. More that 20-year period of operation of a stationary water-vacuum facility and washing the electromagnetic pump for BN-350 fast nuclear reactor directly at is test rig are the best proofs of the proposed method. This method is well suitable for washing the equipment contaminated by radioactive sodium, because by-products of the process are simply utilized. The method is used in a number of Russian enterprises, and recommended for implementation at BN-350 and BN-600 reactor plants. (author)

Radiation heritage of the past in the Republic of Kazakhstan

International Nuclear Information System (INIS)

Cherepnin, Yu.S.; Tukhvatulin, Sh.T.; Mukusheva, M.K.; Kadyrzhanov, K.K.; Akhmetov, M.A.; Baldov, A.N.; Zhantikin, T.M.

2002-01-01

For the whole period of the Semipalatinsk Test Site (STS) operation 456 nuclear tests were conducted not only for the purpose of developing nuclear weapons but also as 'peaceful' underground nuclear explosions. Apart from STS in Kazakhstan there are several testing sites where nuclear explosions were conducted for peaceful purposes. These are explosions of Batolit, Meridian, Region series, as well as Azgir and Lira sites. In Kazakhstan there is great number of plants which have been involved in the development of nuclear weapons. Kazakhstan mining industry was the main supplier of natural uranium and nonferrous metals necessary for production of nuclear-rocket weapons. Along with extraction of uranium ore there were complexes dealing with the development of nuclear technologies. For instance, the complex of unique reactor facilities situated at the former Semipalatinsk Test Site where nuclear rocket engines were tested. High-technological industrial BN-350 reactor complex belongs to a new generation of fast breeding reactors. BN-350 reactor is designed mainly for development of new nuclear technologies. This paper contains generalized results of radiation investigations carried out in regions where nuclear experiments were conducted and nuclear facilities are located. (author)

Performance of metallic fuels in liquid-metal fast reactors

International Nuclear Information System (INIS)

Seidel, B.R.; Walters, L.C.; Kittel, J.H.

1984-01-01

Interest in metallic fuels for liquid-metal fast reactors has come full circle. Metallic fuels are once again a viable alternative for fast reactors because reactor outlet temperature of interest to industry are well within the range where metallic fuels have demonstrated high burnup and reliable performance. In addition, metallic fuel is very tolerant of off-normal events of its high thermal conductivity and fuel behavior. Futhermore, metallic fuels lend themselves to compact and simplified reprocessing and refabrication technologies, a key feature in a new concept for deployment of fast reactors called the Integral Fast Reactor (IFR). The IFR concept is a metallic-fueled pool reactor(s) coupled to an integral-remote reprocessing and fabrication facility. The purpose of this paper is to review recent metallic fuel performance, much of which was tested and proven during the twenty years of EBR-II operation

Fast reactor core monitoring device

International Nuclear Information System (INIS)

Sanda, Toshio; Inoue, Kotaro; Azekura, Kazuo.

1982-01-01

Purpose: To enable the rapid and accurate on-line identification of the state of a fast reactor core by effectively utilizing the measured data on the temperature and flow rate of the coolant. Constitution: The spacial power distribution and average assembly power are quickly calculated using an approximate calculating method, the measured values and the calculated values of the inlet and outlet temperature difference, flow rate and coolant physical values of an assembly are combined and are individually obtained, the most definite respective values and their errors are obtained by a least square method utilizing a formula of the relation between these values, and the power distribution and the temperature distribution of a reactor core are estimated in this manner. Accordingly, even when the measuring accuracy and the calculating accuracy are equal as in a fast reactor, the power distribution and the temperature distribution can be accurately estimated on-line at a high speed in a nuclear reactor, information required for the operator is provided, and the reactor can thus be safely and efficiently operated. (Yoshihara, H.)

A comparison of radioactive waste from first generation fusion reactors and fast fission reactors with actinide recycling

International Nuclear Information System (INIS)

Koch, M.; Kazimi, M.S.

1991-04-01

Limitations of the fission fuel resources will presumably mandate the replacement of thermal fission reactors by fast fission reactors that operate on a self-sufficient closed fuel cycle. This replacement might take place within the next one hundred years, so the direct competitors of fusion reactors will be fission reactors of the latter rather than the former type. Also, fast fission reactors, in contrast to thermal fission reactors, have the potential for transmuting long-lived actinides into short-lived fission products. The associated reduction of the long-term activation of radioactive waste due to actinides makes the comparison of radioactive waste from fast fission reactors to that from fusion reactors more rewarding than the comparison of radioactive waste from thermal fission reactors to that from fusion reactors. Radioactive waste from an experimental and a commercial fast fission reactor and an experimental and a commercial fusion reactor has been characterized. The fast fission reactors chosen for this study were the Experimental Breeder Reactor 2 and the Integral Fast Reactor. The fusion reactors chosen for this study were the International Thermonuclear Experimental Reactor and a Reduced Activation Ferrite Helium Tokamak. The comparison of radioactive waste parameters shows that radioactive waste from the experimental fast fission reactor may be less hazardous than that from the experimental fusion reactor. Inclusion of the actinides would reverse this conclusion only in the long-term. Radioactive waste from the commercial fusion reactor may always be less hazardous than that from the commercial fast fission reactor, irrespective of the inclusion or exclusion of the actinides. The fusion waste would even be far less hazardous, if advanced structural materials, like silicon carbide or vanadium alloy, were employed

A comparison of radioactive waste from first generation fusion reactors and fast fission reactors with actinide recycling

Energy Technology Data Exchange (ETDEWEB)

Koch, M.; Kazimi, M.S.

1991-04-01

Limitations of the fission fuel resources will presumably mandate the replacement of thermal fission reactors by fast fission reactors that operate on a self-sufficient closed fuel cycle. This replacement might take place within the next one hundred years, so the direct competitors of fusion reactors will be fission reactors of the latter rather than the former type. Also, fast fission reactors, in contrast to thermal fission reactors, have the potential for transmuting long-lived actinides into short-lived fission products. The associated reduction of the long-term activation of radioactive waste due to actinides makes the comparison of radioactive waste from fast fission reactors to that from fusion reactors more rewarding than the comparison of radioactive waste from thermal fission reactors to that from fusion reactors. Radioactive waste from an experimental and a commercial fast fission reactor and an experimental and a commercial fusion reactor has been characterized. The fast fission reactors chosen for this study were the Experimental Breeder Reactor 2 and the Integral Fast Reactor. The fusion reactors chosen for this study were the International Thermonuclear Experimental Reactor and a Reduced Activation Ferrite Helium Tokamak. The comparison of radioactive waste parameters shows that radioactive waste from the experimental fast fission reactor may be less hazardous than that from the experimental fusion reactor. Inclusion of the actinides would reverse this conclusion only in the long-term. Radioactive waste from the commercial fusion reactor may always be less hazardous than that from the commercial fast fission reactor, irrespective of the inclusion or exclusion of the actinides. The fusion waste would even be far less hazardous, if advanced structural materials, like silicon carbide or vanadium alloy, were employed.

Pool type liquid metal fast breeder reactors

International Nuclear Information System (INIS)

Guthrie, B.M.

1978-08-01

Various technical aspects of the liquid metal fast breeder reactor (LMFBR), specifically pool type LMFBR's, are summarized. The information presented, for the most part, draws upon existing data. Special sections are devoted to design, technical feasibility (normal operating conditions), and safety (accident conditions). A survey of world fast reactors is presented in tabular form, as are two sets of reference reactor parameters based on available data from present and conceptual LMFBR's. (auth)

Sodium cooled fast reactor

Energy Technology Data Exchange (ETDEWEB)

Hokkyo, N; Inoue, K; Maeda, H

1968-11-21

In a sodium cooled fast neutron reactor, an ultrasonic generator is installed at a fuel assembly hold-down mechanism positioned above a blanket or fission gas reservoir located above the core. During operation of the reactor an ultrsonic wave of frequency 10/sup 3/ - 10/sup 4/ Hz is constantly transmitted to the core to resonantly inject the primary bubble with ultrasonic energy to thereby facilitate its growth. Hence, small bubbles grow gradually to prevent the sudden boiling of sodium if an accident occurs in the cooling system during operation of the reactor.

Simulating the Behaviour of the Fast Reactor Joyo (Draft)

International Nuclear Information System (INIS)

Juutilainen, Pauli

2008-01-01

Motivated by the development of fast reactors the behaviour of the Japanese experimental fast reactor Joyo is simulated with two Monte Carlo codes: Monte Carlo NParticle (MCNP) and Probabilistic Scattering Game (PSG). The simulations are based on the benchmark study 'Japan's Experimental Fast Reactor Joyo MKI core: Sodium-Cooled Uranium-Plutonium Mixed Oxide Fueled Fast Core Surrounded by UO 2 Blanket'. The study is focused on the criticality of the reactor, control rod worth, sodium void reactivity and isothermal temperature coefficient of the reactor. These features are calculated by applying both homogeneous and heterogeneous reactor core models that are built according to the benchmark instructions. The results of the two models obtained by the two codes are compared with each other and especially with the experimental results presented in the benchmark. (author)

BN-600 MOX Core Benchmark Analysis. Results from Phases 4 and 6 of a Coordinated Research Project on Updated Codes and Methods to Reduce the Calculational Uncertainties of the LMFR Reactivity Effects

International Nuclear Information System (INIS)

2013-12-01

For those Member States that have or have had significant fast reactor development programmes, it is of utmost importance that they have validated up to date codes and methods for fast reactor physics analysis in support of R and D and core design activities in the area of actinide utilization and incineration. In particular, some Member States have recently focused on fast reactor systems for minor actinide transmutation and on cores optimized for consuming rather than breeding plutonium; the physics of the breeder reactor cycle having already been widely investigated. Plutonium burning systems may have an important role in managing plutonium stocks until the time when major programmes of self-sufficient fast breeder reactors are established. For assessing the safety of these systems, it is important to determine the prediction accuracy of transient simulations and their associated reactivity coefficients. In response to Member States' expressed interest, the IAEA sponsored a coordinated research project (CRP) on Updated Codes and Methods to Reduce the Calculational Uncertainties of the LMFR Reactivity Effects. The CRP started in November 1999 and, at the first meeting, the members of the CRP endorsed a benchmark on the BN-600 hybrid core for consideration in its first studies. Benchmark analyses of the BN-600 hybrid core were performed during the first three phases of the CRP, investigating different nuclear data and levels of approximation in the calculation of safety related reactivity effects and their influence on uncertainties in transient analysis prediction. In an additional phase of the benchmark studies, experimental data were used for the verification and validation of nuclear data libraries and methods in support of the previous three phases. The results of phases 1, 2, 3 and 5 of the CRP are reported in IAEA-TECDOC-1623, BN-600 Hybrid Core Benchmark Analyses, Results from a Coordinated Research Project on Updated Codes and Methods to Reduce the

The UK commercial demonstration fast reactor design

International Nuclear Information System (INIS)

Holmes, J.A.G.

1987-01-01

The paper on the UK Commercial Demonstration Fast Reactor design was presented to the seminar on 'European Commercial Fast Reactor Programme, London 1987. The design is discussed under the topic headings:- primary circuit, intermediate heat exchangers and pumps, fuel and core, refuelling, steam generators, and nuclear island layout. (U.K.)

A review of fast reactor programme in Japan

International Nuclear Information System (INIS)

Matsuno, Y.; Bando, S.

1981-03-01

The fast breeder reactor development project in Japan made progress in the past year, and will be continued in the next fiscal 1981. The scale of efforts both in budget and personnel will be similar to those in fiscal 1980. The budget for R and D works and for the construction of the fast breeder prototype reactor ''Monju'' will be approximately 20 billion yen and 27 billion yen, respectively, excluding the wage of the personnel concerned. The number of the technical personnel currently engaging in fast breeder reactor development in the Power Reactor and Nuclear Fuel Development Corp. is about 530. As for the experimental fast reactor ''Joyo'', three operational cycles at 75 MWt have been completed in August, 1980, and the fourth cycle has started in March, 1981. As for the prototype reactor ''Monju'', progress was made toward the construction, and the environmental impact statement on the reactor was approved by the authorities concerned. The studies on the preliminary design of large LMFBRs have been made by the PNC and also by power companies. The design study carried out by the PNC is concerned with a 1000 MWe plant of loop type by extrapolating the technology to be developed by the time of the commissioning of ''Monju''. The highlights and topics in the development activities for fast breeder reactors in the past twelve months are summarized in this report. (Kako, I.)

Fast Reactor Programme. Third Quarter 1969. Progress Report

International Nuclear Information System (INIS)

Hoekstra, E.K.

1970-02-01

The RCN research programme on fast spectrum nuclear reactors comprises reactor physics, fuel performance, radiation damage in canning materials, corrosion behaviour in canning materials, aerosol research and heat transfer and hydraulics. An overview is given of the fast reactor experiments at the STEK critical facility in Petten, the Netherlands, in the third quarter of 1969

Conceptual design study on very small long-life gas cooled fast reactor using metallic natural Uranium-Zr as fuel cycle input

International Nuclear Information System (INIS)

Monado, F.; Permana, S.

2013-01-01

Full-text: A conceptual design study of very small 350 MWth Gas-cooled Fast Reactors with Helium coolant has been performed. In this study Modified CANDLE burn-up scheme was implemented to create small and long life fast reactors with natural Uranium as fuel cycle input. Such system can utilize natural Uranium resources efficiently without the necessity of enrichment plant or reprocessing plant. The core with metallic fuel based was subdivided into 10 regions with the same volume. The fresh Natural Uranium is initially put in region-1, after one cycle of 10 years of burn-up it is shifted to region-2 and the each region-1 is filled by fresh Natural Uranium fuel. This concept is basically applied to all axial regions. The reactor discharge burn-up is 31.8 % HM. From the neutronic point of view, this design is in compliance with good performance. (author)

Conceptual design study on very small long-life gas cooled fast reactor using metallic natural Uranium-Zr as fuel cycle input

International Nuclear Information System (INIS)

Monado, Fiber; Ariani, Menik; Su'ud, Zaki; Waris, Abdul; Basar, Khairul; Permana, Sidik; Aziz, Ferhat; Sekimoto, Hiroshi

2014-01-01

A conceptual design study of very small 350 MWth Gas-cooled Fast Reactors with Helium coolant has been performed. In this study Modified CANDLE burn-up scheme was implemented to create small and long life fast reactors with natural Uranium as fuel cycle input. Such system can utilize natural Uranium resources efficiently without the necessity of enrichment plant or reprocessing plant. The core with metallic fuel based was subdivided into 10 regions with the same volume. The fresh Natural Uranium is initially put in region-1, after one cycle of 10 years of burn-up it is shifted to region-2 and the each region-1 is filled by fresh Natural Uranium fuel. This concept is basically applied to all axial regions. The reactor discharge burn-up is 31.8% HM. From the neutronic point of view, this design is in compliance with good performance

Fast wave current drive in reactor scale tokamaks

International Nuclear Information System (INIS)

Moreau, D.

1992-01-01

The IAEA Technical Committee Meeting on Fast Wave Current Drive in Reactor Scale Tokamaks, hosted by the Commissariat a l'Energie Atomique (CEA), Departement de Recherches sur la Fusion Controlee (Centres d'Etudes de Cadarache, under the Euratom-CEA Association for fusion) aimed at discussing the physics and the efficiency of non-inductive current drive by fast waves. Relevance to reactor size tokamaks and comparison between theory and experiment were emphasized. The following topics are described in the summary report: (i) theory and modelling of radiofrequency current drive (theory, full wave modelling, ray tracing and Fokker-Planck calculations, helicity injection and ponderomotive effects, and alternative radio-frequency current drive effects), (ii) present experiments, (iii) reactor applications (reactor scenarios including fast wave current drive; and fast wave current drive antennas); (iv) discussion and summary. 32 refs

General remarks on fast neutron reactor physics

International Nuclear Information System (INIS)

Barre, J.Y.

1980-01-01

The main aspects of fast reactor physics, presented in these lecture notes, are restricted to LMFBR's. The emphasis is placed on the core neutronic balance and the burn-up problems. After a brief description of the power reactor main components and of the fast reactor chronology, the fundamental parameters of the one-group neutronic balance are briefly reviewed. Then the neutronic burn-up problems related to the Pu production and to the doubling time are considered

Material choices for the commercial fast reactor steam generators

International Nuclear Information System (INIS)

Willby, C.; Walters, J.

1978-01-01

Experience with fast reactor steam generators has shown them to be critical components in achieving a high availability. This paper presents the designers views on the use of ferritic materials for steam generators and describes the proposed design of the steam generators for the Commercial Fast Reactor (CFR), prototype of which are to be inserted in the Prototype Fast Reactor at Dounreay. (author)

The fast reactor and electricity supply, a utility view

International Nuclear Information System (INIS)

Wright, J.K.; Hall, R.S.; Kemmish, W.B.; Thorne, R.T.

1982-01-01

The significance of the fast reactor is discussed from the viewpoint of the Central Electricity Generating Board. The need for the fast reactor and a possible timescale for its introduction are examined. It is emphasised that demonstration of the commercial and environmental acceptability of the fuel cycle will be needed before any commitment can be made to fast reactors. (U.K.)

A review of fast reactor progress in Japan

Energy Technology Data Exchange (ETDEWEB)

Tomabechi, K [Power Reactor and Nuclear Fuel Development Corporation, Tokyo (Japan)

1978-07-01

The fast reactor development project in Japan is continuing at a slightly increased scale of effort in budget. The total budget for LMFBR development for fiscal year 1978 was 24 billion yen. In August 1977 major industries engaged in LMFBR have set up an office where design work can be jointly conducted. Highlights and topics of the fast reactor development activities cover description of JOYO reactor, its first criticality experiment, and the prototype fast breeder MONJU. Research and development programmes dealt with fission products release and its possible interaction with the soodium coolant, inspection of reactor components, experiments simulating sodium leakage, development of steam generator.

International standardization of safety requirements for fast reactors

International Nuclear Information System (INIS)

2011-06-01

Japan Atomic Energy Agency (JAEA) is conducting the FaCT (Fast Reactor Cycle Technology Development) project in cooperation with Japan Atomic Power Company (JAPC) and Mitsubishi FBR systems inc. (MFBR), where an advanced loop-type fast reactor named JSFR (Japan Sodium-cooled Fast Reactor) is being developed. It is important to develop software technologies (a safety guideline, safety design criteria, safety design standards etc.) of FBRs as well as hardware ones (a reactor plant itself) in order to address prospective worldwide utilization of FBR technology. Therefore, it is expected to establish a rational safety guideline applicable to the JSFR and harmonized with national nuclear-safety regulations as well, including Japan, the United States and the European Union. This report presents domestic and international status of safety guideline development for sodium-cooled fast reactors (SFRs), results of comparative study for safety requirements provided in existing documents and a proposal for safety requirements of future SFRs with a roadmap for their refinement and worldwide utilization. (author)

Studying the processes of sodium-water interaction in the BOR-60 reactor micromodule steam generator

International Nuclear Information System (INIS)

Tsykanov, V.A.; Antipin, G.K.; Borisov, V.V.

1981-01-01

Main results of experimental studies of emergency regimes of micromodule steam generator (MSG) at small and big leaks of water into sodium, realized using the 30 MW MSG, operating in the BOR-o0 reactor, are considered. The aims of the study are as follows: the modelling of macroleak in ''Nadja'' steam generator for the BN-350 reactor; testing the conceptions of alarm signalling and MSG protection; testing under real conditions of new perspective systems of leak detection; gaining the experimence and development of the ways to eliminate the consequences of accident caused by big water leak into sodium; accumulation of knowledge on restoration of MSG operating ability after accident; experimental test of calculational techniques for big leak accidents to use them in future for calculational studies of similar situations at other reactors equipped with sodium-water steam generators; refinement of characteristics of hydrodynamic and thermal effects interaction zone for big leak in real circuit during the plant operation. A series of experiments with the imitation of water leak into sodium by means of argon and steam supply through injection devices, located before the steam superheater module of one of the sections and between evaporator module of the same section, is conducted. The range of steam flow rate is 0.02-0.45 g/s. Duration of steam supply is 100-400 s. A conclusion is made that the results obtained can be used for steam generator of the BN-350 reactor [ru

Heterogeneity of structure and properties of 12Cr18Ni10Ti and 08Cr16Ni11Mo3 stainless steels irradiated up to high damaging doses in reactor Bn-350

International Nuclear Information System (INIS)

Maksimkin, O.P.; Tivanova, O.V.; Turubarova, L.G.; Silnyagina, N.S.; Doronina, T.A.

2006-01-01

Full text: Earlier, during investigation of post-operating properties and structure of responsible units of fast neutron reactors there was shown /1, 2/ that depending on character of preliminary treatment of austenite stainless steel (austenization, cold deformation, mechanical and thermal treatment) radiation effects could be different. In /2/ one could observe heterogeneity at swelling of cold- worked hexahedral ducts along perimeter, in particular, the swelling of corners was less than plates'. At the same time after mechanical-thermal treatment the corners swell in 3-5 times of magnitude higher than plates. By the present there are several assumptions about nature of this phenomenon. One of them is a difference of deformation degree of material in corners and plates of the duct. It is known that /3/ external effects (including deformation) induce martensitic γ→α transformation in austenitic steels, due to which the structure and properties of steel are changed. In particular, paramagnetic FCC matrix reveals sites with ferromagnetic BCC structure. Steel heating, containing martensitic α-phase higher than ∼ 450-800 deg C, results in reverse γ→α transformation in material, which in its turn leads to formation of phase phase-hardened austenite. We can expect that only peculiarities of processes of direct and reverse martensitic transformations, which took place during preliminary austenitic steel treatment, will predetermine its behavior under irradiation. Taking into account the above mentioned there have been carried out complex material-scientific investigations of 12Cr18Ni10Ti and 08Cr16Ni11Mo3 steel samples cut off from different sites (both adjacent to corners and far from them) of hexagonal ducts of spent fuel assemblies of BN-350 reactor. There were used samples in the form of plates of different sizes: 5x10x2 mm - for metallographic investigations (microscope Neophot-2) and determination of microhardness (PMT-3); 2x20x0,3 mm - for mechanical

Philosophy of safety evaluation on fast breeder reactor

International Nuclear Information System (INIS)

1981-01-01

This is the report submitted from the special subcommittee on reactor safety standard to the Nuclear Safety Commission on October 14, 1980, and it was decided to temporarily apply this concept to the safety examination on fast breeder reactors. The examination and discussion of this report were performed by taking the prototype reactor ''Monju'' into consideration, which is to be the present target, referring to the philosophy of the safety evaluation on fast breeder reactors in foreign countries and based on the experiences in the fast experimental reactor ''Joyo''. The items applicable to the safety evaluation for liquid metal-cooled fast breeder reactors (LMFBR) as they are among the existing safety examination guidelines are applied. In addition to the existing guidelines, the report describes the matters to be considered specifically for core, fuel, sodium, sodium void, reactor shut-down system, reactor coolant boundary, cover gas boundary and others, intermediate cooling system, removal of decay heat, containment vessels, high temperature structures, and aseismatic property in the safety design of LMFBR's. For the safety evaluation for LMFBR's, the abnormal transient changes in operation and the phenomena to be evaluated as accidents are enumerated. In order to judge the propriety of the criteria of locating LMFBR facilities, the serious and hypothetical accidents are decided to be evaluated in accordance with the guideline for reactor location investigation. (Wakatsuki, Y.)

Advances in fast reactor technology. Proceedings of the 30. meeting of the International Working Group on Fast Reactors

International Nuclear Information System (INIS)

1998-04-01

Individual States were largely responsible for early developments in experimental and prototype liquid metal fast reactors (LMFRs). However, for development of advanced LMFRs, international co-operation plays an important role. The IAEA seeks to promote such co-operation. For R and D incorporating innovative features, international co-operation allows pooling of resources and expertise in areas of common interest. Information on experience gained from R and D, and from the operation and construction of fast reactors, has been reviewed periodically by the International Working Group on Fast Reactors (IWGFR). These proceedings contain updated a new information on the status of LMFR development, as reported at the 30th meeting of the IWGFR, held in Beijing, China, from 13 to 16 May 1997

Advances in fast reactor technology. Proceedings of the 30. meeting of the International Working Group on Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

Individual States were largely responsible for early developments in experimental and prototype liquid metal fast reactors (LMFRs). However, for development of advanced LMFRs, international co-operation plays an important role. The IAEA seeks to promote such co-operation. For R and D incorporating innovative features, international co-operation allows pooling of resources and expertise in areas of common interest. Information on experience gained from R and D, and from the operation and construction of fast reactors, has been reviewed periodically by the International Working Group on Fast Reactors (IWGFR). These proceedings contain updated a new information on the status of LMFR development, as reported at the 30th meeting of the IWGFR, held in Beijing, China, from 13 to 16 May 1997. Refs,figs,tabs.

The Integral Fast Reactor

International Nuclear Information System (INIS)

Till, C.E.

1985-01-01

During the past two years, scientists from Argonne have developed an advanced breeder reactor with a closed self contained fuel cycle. The Integral Fast Reactor (IFR) is a new reactor concept, adaptable to a variety of designs, that is based on a fuel cycle radically different from the CRBR line of breeder development. The essential features of the IFR are metal fuel, pool layout, and pyro- and electro-reprocessing in a facility integral with the reactor plant. The IFR shows promise to provide an inexhaustible, safe, economic, environmentally acceptable, and diversion resistant source of nuclear power. It shows potential for major improvement in all of the areas that have led to concern about nuclear power

Calculation of energetic characteristics of C-14 emitted from Beloyarsk nuclear power plant plume with fast neutron reactor

Science.gov (United States)

Kolotkov, Gennady A.; Penin, Sergei

2017-11-01

The paper examines an update of comparative analysis of radionuclides released into the atmosphere from Beloyarsk nuclear power plant with fast-neutron reactor for nine years in a row, from 2008 to 2016. It has been shown that the main radionuclides throw out into the atmosphere from Beloyarsk nuclear power plant are beta-active radionuclides. Based on data releases of the RPA "Typhoon", it has been conclude that radiation situation become worse insignificantly; beside on the new reactor BN-800 was put in operation in 2016. Using Spencer-Fano's equation, it was carried out the summary spectrum of emitted radionuclides. On example of Beloyarsk nuclear power plant, it was considered a question about ability of remote detection of raised radioactivity in the atmospheric radioactive plume. It has been shown that it possible to detect raised radioactivity in the emission plume from Beloyarsk nuclear power plant.

Logistical and economic obstacles to a fast reactor programme

International Nuclear Information System (INIS)

Sweet, C.

1982-01-01

Fast reactor studies used to place great emphasis on its role as a breeder of plutonium, thereby raising the prospect of a nuclear power system free from the constraint of uranium supplies. Today, not only the timing of fast reactor introduction has slipped (by two or three decades) but the perspective which was central to energy policy has changed dramatically. This article first examines the fast reactor as a system and looks at the interaction of four key variables in its logistics. It then looks at the rise in real costs, especially capital costs. Given the parameters that determine the plutonium balance and the economics of the fast reactor system, the author questions whether there is a sound basis for its introduction, and concludes by suggesting that the most pressing requirement is a study of the opportunity costs of fast reactor R and D expenditures. (author)

Calculation of the neutron parameters of fast thermal reactor

International Nuclear Information System (INIS)

Kukuleanu, V.; Mocioiu, D.; Drutse, E.; Konstantinesku, E.

1975-01-01

The system of neutron calculation for fast reactors is given. This system was used for estimation of physical parameters of fast thermal reactors investigated. The results obtained and different specific problems of the reactors of this type are described. (author)

Fast reactor research activities in Brazil

International Nuclear Information System (INIS)

Menezes, A.

1998-01-01

Fast reactor activities in Brazil have the objective of establishing a consistent knowledge basis which can serve as a support for a future transitions to the activities more directly related to design, construction and operation of an experimental fast reactor, although its materialization is still far from being decided. Due to the present economic difficulties and uncertainties, the program is modest and all efforts have been directed towards its consolidation, based on the understanding that this class of reactors will play an important role in the future and Brazil needs to be minimally prepared. The text describes the present status of those activities, emphasizing the main progress made in 1996. (author)

Direct conversion of h-BN into c-BN and formation of epitaxial c-BN/diamond heterostructures

International Nuclear Information System (INIS)

Narayan, Jagdish; Bhaumik, Anagh; Xu, Weizong

2016-01-01

We have created a new state of BN (named Q-BN) through rapid melting and super undercooling and quenching by using nanosecond laser pulses. Phase pure c-BN is formed either by direct quenching of super undercooled liquid or by nucleation and growth from Q-BN. Thus, a direct conversion of hexagonal boron nitride (h-BN) into phase-pure cubic boron nitride (c-BN) is achieved by nanosecond pulsed laser melting at ambient temperatures and atmospheric pressure in air. According to the P-T phase diagram, the transformation from h-BN into c-BN under equilibrium processing can occur only at high temperatures and pressures, as the hBN-cBN-Liquid triple point is at 3500 K/9.5 GPa or 3700 K/7.0 GPa with a recent theoretical refinement. Using nonequilibrium nanosecond laser melting, we have created super undercooled state and shifted this triple point to as low as 2800 K and atmospheric pressure. The rapid quenching from super undercooled state leads to the formation of a new phase, named as Q-BN. We present detailed characterization of Q-BN and c-BN layers by using Raman spectroscopy, high-resolution scanning electron microscopy, electron-back-scatter diffraction, high-resolution TEM, and electron energy loss spectroscopy, and discuss the mechanism of formation of nanodots, nanoneedles, microneedles, and single-crystal c-BN on sapphire substrate. We have also deposited diamond by pulsed laser deposition of carbon on c-BN and created c-BN/diamond heterostructures, where c-BN acts as a template for epitaxial diamond growth. We discuss the mechanism of epitaxial c-BN and diamond growth on lattice matching c-BN template under pulsed laser evaporation of amorphous carbon, and the impact of this discovery on a variety of applications.

A review of the Italian fast reactor programme

International Nuclear Information System (INIS)

Pierantoni, F.; Tavoni, R.

1984-01-01

This review sums up the Italian situation in the field of the fast reactors on the eve of the fifth five year plan (1985-1989), in which the country undertakes to implement an important activity of research and development in the context of a greater European collaboration. Italian participation in the development of European nuclear power stations together with the completion of the PEC plant which will be used to develop a fuel element with the necessary economic and safety characteristics, remain the two principal goals of the Italian fast reactor programme. In 1983 the sum assigned by ENEA for fast reactors was about 220 billion lire of which 145 billion was for the PEC reactor

Today's attitudes and future prospects of fast reactors in Italy

International Nuclear Information System (INIS)

Barabaschi, S.; Cicognani, G.; Pierantoni, F.

1982-01-01

The Italian fast reactor programme is reviewed. The 15 year collaboration with France has resulted in the construction of the PEC reactor, development of the Superphenix-1 and a common R and D programme for future large fast reactors. The CNEN 4th five year (1980-84) plan is outlined. The budget breakdown for different areas shows the importance attached to the fast reactor. (U.K.)

A review of the UK fast reactor programme, March 1979

Energy Technology Data Exchange (ETDEWEB)

Smith, R D

1979-07-01

The Status report of the UK activities related to fast-breeder reactor activities includes the following: summary of the operating experience of the prototype Fast Reactor (PFR) during 1978; design studies of the commercial demonstration fast reactor (CDFR); design studies of later advanced LMFBR; engineering developments of high temperature sodium loop, steam generators and instrumentation; materials development; corrosion problems; sodium technology; fuel elements development; PFR fuel reprocessing; safety issues molten fuel-coolant interaction; core structure test; accident analysis; reactor performance studies; experimental reactor physics; fuel management and general neutronics calculation for CDFR; reactor instruments.

A review of the UK fast reactor programme, March 1979

International Nuclear Information System (INIS)

Smith, R.D.

1979-01-01

The Status report of the UK activities related to fast-breeder reactor activities includes the following: summary of the operating experience of the prototype Fast Reactor (PFR) during 1978; design studies of the commercial demonstration fast reactor (CDFR); design studies of later advanced LMFBR; engineering developments of high temperature sodium loop, steam generators and instrumentation; materials development; corrosion problems; sodium technology; fuel elements development; PFR fuel reprocessing; safety issues molten fuel-coolant interaction; core structure test; accident analysis; reactor performance studies; experimental reactor physics; fuel management and general neutronics calculation for CDFR; reactor instruments

International Working Group on Fast Reactors Sixth Annual Meeting. Summary Report

International Nuclear Information System (INIS)

1973-01-01

The Agenda of the Meeting was as follows: 1. Review of IWGFR Activities - 1a. Approval of the minutes of the Fifth IWGFR Meeting. 1b. Report by Scientific Secretary regarding the activities of the Group. 2. Comments on National Programmes on Fast Breeder Reactors. 3. International Coordination of the Schedule for Major Fast Reactor Meetings and other major international meetings having a predominant fast reactor interest. 4. Consideration of Conferences on Fast Reactors. 4a. IAEA Symposium on Fuel and Fuel Elements for Fast Reactors, Brussels, Belgium 2-6 July 1973. 4b. International Symposium on Physics of Fast Reactors, Tokyo, Japan, 16 to 23 October 1973. 4c. International Conference on Fast Reactor Power Stations, London, UK, 11 to 14 March 1974 . 4d. Suggestions of the IWGFR members on other conferences. 5. Consideration of a Schedule for Specialists' Meetings in 1973-74. 6. Other Business - 6a. First-aid in Sodium Burns. 6b. Principles of Good Practice for Safe Operation of Sodium Circuits. 6c. Bibliography on Fast Reactors. 7. The Date and Place of the Seventh Annual Meeting of the IWGFR

The integral fast reactor concept

International Nuclear Information System (INIS)

Chang, Yoon I.; Marchaterre, J.F.

1987-01-01

The Integral Fast Reactor (IFR) is an innovative liquid metal reactor concept being developed at Argonne National Laboratory. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system. The IFR concept consists of four technical features: (1) liquid sodium cooling, (2) pool-type reactor configuration, (3) metallic fuel, and (4) an integral fuel cycle, based on pyrometallurgical processing and injection-cast fuel fabrication, with the fuel cycle facility collocated with the reactor, if so desired. This paper gives a review of the IFR concept

The 'SURA' fast reactor program

International Nuclear Information System (INIS)

Anon.

1979-01-01

The Commissariat a l'Energie Atomique's SURA program on fast reactor safety consists of two specific testing programs on fastbreeder reactor safety: the Cabri and Scarabee programs. Both Cabri and Scarabee are examples of multinational research collaboration. The CEA and the Karlsruhe Nuclear Research Center are each covering half of the construction costs. Britain, the US and Japan are also due to participate in these experiments. The aim of the programs is to examine the behaviour of fuel in sodium cooled fast reactors. The Cabri program consists of setting off a reactivity accident in a power reactor core which is cooled with liquid sodium, such an accident occurring after a sharp increase in reactivity or as a result of the pump suddenly breaking down without there at the same time being any fall in the control rods. In 1967 the Commissariat a l'Energie Atomique started its Scarabee research program which is trying to analyse the sort of things that can go wrong with fuel cooling systems and what the consequences can be [fr

A Review of Fast Reactor Programme in India, April 1930

International Nuclear Information System (INIS)

Paranjpe, S.R.

1980-01-01

Nuclear energy has to play a significant role in the energy resources of India in the next century. To-day's apparently vast reserves of fossil fuels would be under severe strain due to rapidly increasing demand for energy. Long-term perspective planning requires Nuclear Energy to play a significant role from early part of the next century and share a major load. But, India is not endowed with vast reserves of uranium and must therefore aim to utilise more abundant thorium reserves which are estimated to be about 350,000 tonnes. Department of Atomic Energy which is responsible for the development of nuclear energy in India has therefore planned a step-wise approach consisting of: (i) First phase of the programme of natural uranium based thermal reactors to produce power and plutonium which is the basis of the next phase. (ii) Second phase of the programme to produce power and breed more and more plutonium through fast breeder deployment so as to build sufficient inventories of fissile material which can then become the basis of the third stage. (iii) To utilise thorium with the help of fissile material produced by 2nd phase of Breeder Reactors

A Review of Fast Reactor Programme in India, April 1930

Energy Technology Data Exchange (ETDEWEB)

Paranjpe, S. R. [Reactor Research Centre Kalpakkam, Tamil Nadu (India)

1980-10-15

Nuclear energy has to play a significant role in the energy resources of India in the next century. To-day's apparently vast reserves of fossil fuels would be under severe strain due to rapidly increasing demand for energy. Long-term perspective planning requires Nuclear Energy to play a significant role from early part of the next century and share a major load. But, India is not endowed with vast reserves of uranium and must therefore aim to utilise more abundant thorium reserves which are estimated to be about 350,000 tonnes. Department of Atomic Energy which is responsible for the development of nuclear energy in India has therefore planned a step-wise approach consisting of: (i) First phase of the programme of natural uranium based thermal reactors to produce power and plutonium which is the basis of the next phase. (ii) Second phase of the programme to produce power and breed more and more plutonium through fast breeder deployment so as to build sufficient inventories of fissile material which can then become the basis of the third stage. (iii) To utilise thorium with the help of fissile material produced by 2nd phase of Breeder Reactors.

Fission energy: The integral fast reactor

International Nuclear Information System (INIS)

Chang, Yoon I.

1989-01-01

The Integral Fast Reactor (IFR) is an innovative reactor concept being developed at Argonne National Laboratory as a such next- generation reactor concept. The IFR concept has a number of specific technical advantages that collectively address the potential difficulties facing the expansion of nuclear power deployment. In particular, the IFR concept can meet all three fundamental requirements needed in a next-generation reactor as discussed below. This document discusses these requirements

Fission energy: The integral fast reactor

Energy Technology Data Exchange (ETDEWEB)

Chang, Yoon I.

1989-01-01

The Integral Fast Reactor (IFR) is an innovative reactor concept being developed at Argonne National Laboratory as a such next- generation reactor concept. The IFR concept has a number of specific technical advantages that collectively address the potential difficulties facing the expansion of nuclear power deployment. In particular, the IFR concept can meet all three fundamental requirements needed in a next-generation reactor as discussed below. This document discusses these requirements.

Aspects of the fast reactors fuel cycle

International Nuclear Information System (INIS)

Zouain, D.M.

1982-06-01

The fuel cycle for fast reactors, is analysed, regarding the technical aspects of the developing of the reprocessing stages and the fuel fabrication. The environmental impact of LMFBRs and the waste management of this cycle are studied. The economic aspects of the fuel cycle, are studied too. Some coments about the Brazilian fast reactors programs are done. (E.G.) [pt

Status of the DEBENE fast breeder reactor development, March 1979

International Nuclear Information System (INIS)

Daeunert, U.; Kessler, G.

1979-01-01

Status report of the Fast-breeder reactor development in Germany covers the following: description of the political situation in Federal republic of germany during 1978; international cooperation in the field of fast reactor technology development; operation description of the KNK-II fast core experimental power plant; status of construction of the SNR-300; results of the research and development programs concerned with fuel element, cladding, absorber rods and core structural materials development; sodium effects; neutron irradiation effects on SS properties; reactor physics related to experiments in fast critical assemblies; fast reactor safety issues; core disruption accidents; sodium boiling experiments, measuring methods developed; component tests

Status of the DEBENE fast breeder reactor development, March 1979

Energy Technology Data Exchange (ETDEWEB)

Daeunert, U; Kessler, G

1979-07-01

Status report of the Fast-breeder reactor development in Germany covers the following: description of the political situation in Federal republic of germany during 1978; international cooperation in the field of fast reactor technology development; operation description of the KNK-II fast core experimental power plant; status of construction of the SNR-300; results of the research and development programs concerned with fuel element, cladding, absorber rods and core structural materials development; sodium effects; neutron irradiation effects on SS properties; reactor physics related to experiments in fast critical assemblies; fast reactor safety issues; core disruption accidents; sodium boiling experiments, measuring methods developed; component tests.

Nuclear data for advanced fast reactors

International Nuclear Information System (INIS)

Rabotnov, N.S.

2001-01-01

Interest revives to fast reactors as the only proven technology obviously able of satisfying human energy needs for the next millennium by using full energy content of both natural uranium resources and of vast stocks of depleted uranium. This interest stimulates revision and improvement of fast reactor ND. Progress in reactor calculations accuracy due to better codes and much faster computers also increases relative importance of the input data uncertainties, especially in case of small reactivity margin and fuels of equilibrium compositions. The main objects of corresponding R and D efforts should be minor actinides and heavy liquid metal coolant. Data error bands and covariance information also gain importance as necessary components of neutron physics calculations. (author)

The development of fast simulation program for marine reactor parameters

International Nuclear Information System (INIS)

Chen Zhiyun; Hao Jianli; Chen Wenzhen

2012-01-01

Highlights: ► The simplified physical and mathematical models are proposed for a marine reactor system. ► A program is developed with Simulink module and Matlab file. ► The program developed has the merit of easy input preparation, output processing and fast running. ► The program can be used for the fast simulation of marine reactor parameters on the operating field. - Abstract: The fast simulation program for marine reactor parameters is developed based on the Simulink simulating software according to the characteristics of marine reactor with requirement of maneuverability and acute and fast response. The simplified core physical and thermal model, pressurizer model, steam generator model, control rod model, reactivity model and the corresponding Simulink modules are established. The whole program is developed by coupling all the Simulink modules. Two typical transient processes of marine reactor with fast load increase at low power level and load rejection at high power level are adopted to verify the program. The results are compared with those of Relap5/Mod3.2 with good consistency, and the program runs very fast. It is shown that the program is correct and suitable for the fast and accurate simulation of marine reactor parameters on the operating field, which is significant to the marine reactor safe operation.

Construction schedule management of China Experimental Fast Reactor

International Nuclear Information System (INIS)

Wang Yue

2012-01-01

China Experimental Fast Reactor (CEFR) in the first Fast Reactor in China, which is one of large project of the National High Technology Research and Development Program ('863' Program). On 21 st July 2011, CEFR had succeeded to connect to power grid, the target of construction had come true. To a large item, schedule management is one of the most important management, this paper a overall discussion about CEFR item. It has proved that the management of CEFR project is scientific, normative and high-efficiency, it will be valuable for lager Fast Reactor item and designers in interrelated field. (author)

Upgrading program of the experimental fast reactor Joyo

International Nuclear Information System (INIS)

Yoshida, A.; Yogo, S.

2001-01-01

The experimental fast reactor Joyo finished its operation as an irradiation core in June, 2000. Throughout the operation of MK-I (breeder core) and MK-II (irradiation core), the net operation time has exceeded 60,000 hours. During these operations there were no fuel failures or serious plant problems. The MK-III modification program will improve irradiation capability to demonstrate advanced technologies for commercial Fast Breeder Reactor (FBR). When the MK-III core is started, it will support irradiation tests in feasibility studies for fast reactor and related fuel cycle research and development in Japan. (authors)

RBEC lead-bismuth cooled fast reactor: review of conceptual decisions

International Nuclear Information System (INIS)

Alekseev, P.; Fomichenko, P.; Mikityuk, K.; Nevinitsa, V.; Shchepetina, T.; Subbotin, S.; Vasiliev, A.

2001-01-01

A concept of the RBEC lead-bismuth fast reactor-breeder is a synthesis, on one hand, of more than 40-year experience in development and operation of fast sodium power reactors and reactors with Pb-Bi coolant for nuclear submarines, and, on the other hand, of large R and D activities on development of the core concept for modified fast sodium reactor. The report briefly presents main parameters of the RBEC reactor, as a candidate for commercial exploitation in structure of the future nuclear power. (author)

Dounreay fast reactor

International Nuclear Information System (INIS)

Maclennan, R.; Eggar, T.; Skeet, T.

1992-01-01

The short debate which followed a private notice question asking for a statement on Government policy on the future of the European fast breeder nuclear research programme is reported verbatim. In response to the question, the Minister for Energy said that the Government had decided in 1988 that the Dounreay prototype fast reactor would close in 1994. That decision had been confirmed. Funding of fast breeder research and development beyond 1993 is not a priority as commercialization is not expected until well into the next century. Dounreay will be supported financially until 1994 and then for its subsequent decommissioning and reprocessing of spent fuel. The debate raised issues such as Britain losing its lead in fast breeder research, loss of jobs and the Government's nuclear policy in general. However, the Government's position was that the research had reached a stage where it could be left and returned to in the future. (UK)

A new concept of fast reactors, the potentialities of burning in them of actinoid and weapon-grade plutonium

International Nuclear Information System (INIS)

Murogov, V.M.; Troyanov, M.F.; Ilyunin, V.G.; Rudneva, V.Ya.

1992-01-01

The approach to a possible solution of the problem of peaceful utilization of weapon-grade plutonium released in the result of nuclear disarmament in Russia is given in the repot. As the most safe, ecologically acceptable and economically effective way of the plutonium utilization is the usage of such plutonium as a fuel for atomic power station. It is proposed to decide the problem on the basis of BN-600 and BN-800 reactors. In the approach, thorium could be used as a fertile material. The secondary nuclear fuel U-233 is expedient to use in light-water reactors of new generation. (author)

Thermo-hydraulic simulations of the experimental fast reactor core

International Nuclear Information System (INIS)

Silveira Luz, M. da; Braz Filho, F.A.; Borges, E.M.

1985-01-01

A study of the core and performance of metallic fuel of the experimental fast reactor, from the thermal-hydraulic point of view, was carried out employing the COBRA IV-I code. The good safety characteristics of this reactor and the feasibility of using metallic fuel in experimental fast reactor were demonstrated. (Author) [pt

A review of fast reactor programme in Japan

Energy Technology Data Exchange (ETDEWEB)

Masuno, Y [Experimental Fast Reactor Division, O-arai Engineering Center, PNC (Japan); Bando, S [Project Planning and Management Division, PNC, Minato-ku, Tokyo (Japan)

1981-05-01

The fast breeder reactor development project in Japan has been in progress in the past twelve months and will be continued in the next fiscal year, from April 1981 through March 1982, at a similar scale of effort both in budget and personnel to those of the fiscal year of 1980. The 1981 year budget for P and D work and for construction of a prototype fast breeder reactor, Monju, will be approximately 20 and 27 billion Yen respectively, excluding wages of the personnel of the Power Reactor and Nuclear Fuel Development Corporation, PNC. The number of the technical people currently engaging in the fast breeder reactor development in the PNC is approximately 530, excluding those working for plutonium fuel fabrication. Concerning the experimental fast reactor, Joyo, power increase from 50 MWt to 75 MWt was made in July 1979 and three operational cycles at 75 MWt have been completed in August 1980 and the forth cycle has started in the middle of March 1981. With respect to the prototype reactor Monju, progress toward construction has been made and an environmental impact statement of the reactor was approved by the concerned authorities. Preliminary design studies of large LMFBR are being made by PNC and also by utilities. A design study being conducted by PNC is on a 1000 MW e plant of loop type by extrapolating the technology to be developed by the time of commissioning of Monju. A group of utilities is conducting a similar study, but covering somewhat wider range of parameters and options of design. Close contact between the group and PNC has been kept. In the future, those design efforts will be combined as a single design effort, when a major effort for developing a large demonstration reactor will be initiated at around the commencement of construction of the prototype reactor Monju. Highlights and topics of the fast breeder reactor development activities in the past twelve months are summarized in this report.

A review of fast reactor programme in Japan

International Nuclear Information System (INIS)

Masuno, Y.; Bando, S.

1981-01-01

The fast breeder reactor development project in Japan has been in progress in the past twelve months and will be continued in the next fiscal year, from April 1981 through March 1982, at a similar scale of effort both in budget and personnel to those of the fiscal year of 1980. The 1981 year budget for P and D work and for construction of a prototype fast breeder reactor, Monju, will be approximately 20 and 27 billion Yen respectively, excluding wages of the personnel of the Power Reactor and Nuclear Fuel Development Corporation, PNC. The number of the technical people currently engaging in the fast breeder reactor development in the PNC is approximately 530, excluding those working for plutonium fuel fabrication. Concerning the experimental fast reactor, Joyo, power increase from 50 MWt to 75 MWt was made in July 1979 and three operational cycles at 75 MWt have been completed in August 1980 and the forth cycle has started in the middle of March 1981. With respect to the prototype reactor Monju, progress toward construction has been made and an environmental impact statement of the reactor was approved by the concerned authorities. Preliminary design studies of large LMFBR are being made by PNC and also by utilities. A design study being conducted by PNC is on a 1000 MW e plant of loop type by extrapolating the technology to be developed by the time of commissioning of Monju. A group of utilities is conducting a similar study, but covering somewhat wider range of parameters and options of design. Close contact between the group and PNC has been kept. In the future, those design efforts will be combined as a single design effort, when a major effort for developing a large demonstration reactor will be initiated at around the commencement of construction of the prototype reactor Monju. Highlights and topics of the fast breeder reactor development activities in the past twelve months are summarized in this report

Fast neutron nuclear reactor with lightened internal structure

International Nuclear Information System (INIS)

Artaud, R.; Aubert, M.; Renaux, C.

1984-01-01

The invention concerns an integrated type fast reactor. The inner vessel comprises two truncated shells, of which the large bases are connected either directly, or by a cylindrical shell of large diameter. The small base of the upper truncated shell is prolongated by a shell of small diameter and the small base of the lower truncated shell supports the reactor core. The invention allows the construction of simpler and less expansive fast reactors [fr

Core disruptive accident analysis in prototype fast breeder reactor

International Nuclear Information System (INIS)

Chellapandi, P.; Velusamy, K.; Kannan, S.E.; Singh, Om Pal; Chetal, S.C.; Bhoje, S.B.

2002-01-01

Liquid metal cooled fast breeder reactors, in particular, pool type have many inherent and engineered safety features and hence a core disruptive accident (CDA) involving melt down of the whole core is a very low probable event ( -6 /ry). The important mechanical consequences such as straining of the main vessel including top shield, structural integrity of safety grade decay heat exchangers (DHX) and intermediate heat exchangers (IHX) sodium release to reactor containment building (RCB) through the penetrations in the top shield, sodium fire and consequent temperature and pressure rise in RCB are theoretically analysed using computer codes. Through the analyses with these codes, it is demonstrated that an energetic CDA capability to the maximum 100 MJ mechanical energy in PFBR can be well contained in the primary containment. The sodium release to RCB is 350 kg and pressure rise in RCB is ∼10 kPa. In order to raise the confidence on the theoretical predictions, very systematic experimental program has been carried out. Totally 67 tests were conducted. This experimental study indicated that the primary containment is integral. The main vessel can withstand the energy release of ∼1200 MJ. The structural integrity of IHX and DHX is assured up to 200 MJ. The transient force transmitted to reactor vault is negligible. The average water leak measured under simulated tests for 122 MJ work potential is about 1.8 kg and the maximum leak is 2.41 kg. Extrapolation of the measured maximum leak based on simulation principles yields ∼ 233 kg of sodium leak in the reactor. Based on the above-mentioned theoretical and experimental investigations, the design pressure of 20 kPa is used for PFBR

A next-generation reactor concept: The Integral Fast Reactor (IFR)

Energy Technology Data Exchange (ETDEWEB)

Chang, Y.I.

1992-01-01

The Integral Fast Reactor (IFR) is an advanced liquid metal reactor concept being developed at Argonne National Laboratory as reactor technology for the 21st century. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system, in particular passive safety and waste management. The IFR concept consists of four technical features: (1) liquid sodium cooling, (2) pool-type reactor configuration, (3) metallic fuel, and (4) fuel cycle closure based on pyroprocessing.

A next-generation reactor concept: The Integral Fast Reactor (IFR)

Energy Technology Data Exchange (ETDEWEB)

Chang, Y.I.

1992-07-01

The Integral Fast Reactor (IFR) is an advanced liquid metal reactor concept being developed at Argonne National Laboratory as reactor technology for the 21st century. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system, in particular passive safety and waste management. The IFR concept consists of four technical features: (1) liquid sodium cooling, (2) pool-type reactor configuration, (3) metallic fuel, and (4) fuel cycle closure based on pyroprocessing.

A next-generation reactor concept: The Integral Fast Reactor (IFR)

International Nuclear Information System (INIS)

Chang, Y.I.

1992-01-01

The Integral Fast Reactor (IFR) is an advanced liquid metal reactor concept being developed at Argonne National Laboratory as reactor technology for the 21st century. It seeks to specifically exploit the inherent properties of liquid metal cooling and metallic fuel in a way that leads to substantial improvements in the characteristics of the complete reactor system, in particular passive safety and waste management. The IFR concept consists of four technical features: (1) liquid sodium cooling, (2) pool-type reactor configuration, (3) metallic fuel, and (4) fuel cycle closure based on pyroprocessing

Technical feasibility of an Integral Fast Reactor (IFR) as a future option for fast reactor cycles. Integrate a small metal-fueled fast reactor and pyroprocessing facilities

International Nuclear Information System (INIS)

Tanaka, Nobuo

2017-01-01

Integral Fast Reactor that integrated fast reactor and pyrorocessing facilities developed by Argonne National Laboratory in the U.S. is an excellent nuclear fuel cycle system for passive safety, nuclear non-proliferation, and reduction in radioactive waste. In addition, this system can be considered as a technology applicable to the treatment of the fuel debris caused by the Fukushima Daiichi Nuclear Power Station accident. This study assessed the time required for debris processing, safety of the facilities, and construction cost when using this technology, and examined technological possibility including future technological issues. In a small metal-fueled reactor, it is important to design the core that achieves both of reduction in combustion reactivity and reduction in coolant reactivity. In system design, calorimetric analysis, structure soundness assessment, seismic feasibility establishment study, etc. are important. Regarding safety, research and testing are necessary on the capabilities of passive reactor shutdown and reactor core cooling as well as measures for avoiding re-criticality, even when emergency stop has failed. In dry reprocessing system, studies on electrolytic reduction and electrolytic refining process for treating the debris with compositions different from those of normal fuel are necessary. (A.O.)

Sodium fast reactor safety and licensing research plan - Volume II

International Nuclear Information System (INIS)

Ludewig, H.; Powers, D.A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A.; Phillips, J.; Zeyen, R.; Clement, B.; Garner, Frank; Walters, Leon; Wright, Steve; Ott, Larry J.; Suo-Anttila, Ahti Jorma; Denning, Richard; Ohshima, Hiroyuki; Ohno, S.; Miyhara, S.; Yacout, Abdellatif; Farmer, M.; Wade, D.; Grandy, C.; Schmidt, R.; Cahalen, J.; Olivier, Tara Jean; Budnitz, R.; Tobita, Yoshiharu; Serre, Frederic; Natesan, Ken; Carbajo, Juan J.; Jeong, Hae-Yong; Wigeland, Roald; Corradini, Michael; Thomas, Justin; Wei, Tom; Sofu, Tanju; Flanagan, George F.; Bari, R.; Porter D.

2012-01-01

Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

Sodium fast reactor safety and licensing research plan. Volume II.

Energy Technology Data Exchange (ETDEWEB)

Ludewig, H. (Brokhaven National Laboratory, Upton, NY); Powers, D. A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A. (Argonne National Laboratory, Argonne, IL); Phillips, J.; Zeyen, R. (Institute for Energy Petten, Saint-Paul-lez-Durance, France); Clement, B. (IRSN/DPAM.SEMIC Bt 702, Saint-Paul-lez-Durance, France); Garner, Frank (Radiation Effects Consulting, Richland, WA); Walters, Leon (Advanced Reactor Concepts, Los Alamos, NM); Wright, Steve; Ott, Larry J. (Oak Ridge National Laboratory, Oak Ridge, TN); Suo-Anttila, Ahti Jorma; Denning, Richard (Ohio State University, Columbus, OH); Ohshima, Hiroyuki (Japan Atomic Energy Agency, Ibaraki, Japan); Ohno, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Miyhara, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Yacout, Abdellatif (Argonne National Laboratory, Argonne, IL); Farmer, M. (Argonne National Laboratory, Argonne, IL); Wade, D. (Argonne National Laboratory, Argonne, IL); Grandy, C. (Argonne National Laboratory, Argonne, IL); Schmidt, R.; Cahalen, J. (Argonne National Laboratory, Argonne, IL); Olivier, Tara Jean; Budnitz, R. (Lawrence Berkeley National Laboratory, Berkeley, CA); Tobita, Yoshiharu (Japan Atomic Energy Agency, Ibaraki, Japan); Serre, Frederic (Centre d' %C3%94etudes nucl%C3%94eaires de Cadarache, Cea, France); Natesan, Ken (Argonne National Laboratory, Argonne, IL); Carbajo, Juan J. (Oak Ridge National Laboratory, Oak Ridge, TN); Jeong, Hae-Yong (Korea Atomic Energy Research Institute, Daejeon, Korea); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Corradini, Michael (University of Wisconsin-Madison, Madison, WI); Thomas, Justin (Argonne National Laboratory, Argonne, IL); Wei, Tom (Argonne National Laboratory, Argonne, IL); Sofu, Tanju (Argonne National Laboratory, Argonne, IL); Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN); Bari, R. (Brokhaven National Laboratory, Upton, NY); Porter D. (Idaho National Laboratory, Idaho Falls, ID); Lambert, J. (Argonne National Laboratory, Argonne, IL); Hayes, S. (Idaho National Laboratory, Idaho Falls, ID); Sackett, J. (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.

2012-05-01

Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

The dismantling of fast reactors: sodium processing

International Nuclear Information System (INIS)

Rodriguez, G.; Berte, M.; Serpante, J.P.

1999-01-01

Fast reactors require a coolant that does not slow down neutrons so water can not be used. Metallic sodium has been chosen because of its outstanding neutronic and thermal properties but sodium reacts easily with air and water and this implies that sodium-smeary components can not be considered as usual nuclear wastes. A stage of sodium neutralizing is necessary in the processing of wastes from fast reactors. Metallic sodium is turned into a chemically stable compound: soda, carbonates or sodium salts. This article presents several methods used by Framatome in an industrial way when dismantling sodium-cooled reactors. (A.C.)

Status of fast reactors and ADS programmes in France in 2001

International Nuclear Information System (INIS)

Astegiano, J.C.

2002-01-01

Status of French fast reactor and ADS program in France covers the following topics: data on power generation from NPPs; status of fast reactors, namely Rapsodie, Phenix and Super Phenix; research and development programs concerned with fast gas cooled and sodium cooled reactors

Neutron irradiation of V-Cr-Ti alloys in the BOR-60 fast reactor: Description of the fusion-1 experiment

Energy Technology Data Exchange (ETDEWEB)

Rowcliffe, A.F. [Oak Ridge National Laboratory, TN (United States); Tsai, H.C.; Smith, D.L. [Argonne National Lab., IL (United States)] [and others

1997-08-01

The FUSION-1 irradiation capsule was inserted in Row 5 of the BOR-60 fast reactor in June 1995. The capsule contains a collaborative RF/U.S. experiment to investigate the irradiation performance of V-Cr-Ti alloys in the temperature range 310 to 350{degrees}C. This report describes the capsule layout, specimen fabrication history, and the detailed test matrix for the U.S. specimens. A description of the operating history and neutronics will be presented in the next semiannual report.

Status of fast reactor control rod development in the United Kingdom

International Nuclear Information System (INIS)

Kelly, B.T.

1984-01-01

The two large fast reactors constructed in the United Kingdom, that is the Dounreay Fast Reactor (DFR) and the Prototype Fast Reactor (PFR) differed substantially in their control systems. DFR was controlled by variation of the neutron leakage from the core while PFR uses conventional control rods containing neutron absorbing materials. This paper describes the development of the PFR control systems, the progressive design of the control systems for the prototype Civil Fast Reactor (CFR) and the supporting research and development programmes. (author)

Commission of the European Communities review of fast reactor activities, March 1981

Energy Technology Data Exchange (ETDEWEB)

Balz, W [Commission of the European Communities, Brussels (Belgium)

1981-05-01

The Commission of the European Communities continued its activities in the field of fast reactors development essentially in the frame of the Fast Reactor Coordinating Committee (FRCC) and by execution of a Reactor Programme at its Joint Research Center (JRC). The study was concerned with introducing fast reactors into European Community, elaboration of preliminary safety criteria and guidelines for typical fast reactor accidents; codes and standards; LMFBR safety, fuel, fuel cycle safety.

Commission of the European Communities review of fast reactor activities, March 1981

International Nuclear Information System (INIS)

Balz, W.

1981-01-01

The Commission of the European Communities continued its activities in the field of fast reactors development essentially in the frame of the Fast Reactor Coordinating Committee (FRCC) and by execution of a Reactor Programme at its Joint Research Center (JRC). The study was concerned with introducing fast reactors into European Community, elaboration of preliminary safety criteria and guidelines for typical fast reactor accidents; codes and standards; LMFBR safety, fuel, fuel cycle safety

The integral fast reactor - an overview

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.; Hannum, W.H.

1997-01-01

The Integral Fast Reactor (IFR) is a system that consists of a fast-spectrum nuclear reactor that uses metallic fuel and liquid-metal (sodium) cooling, coupled with technology for high-temperature electrochemical recycling, and with processes for preparing wastes for disposition. The concept is based on decades of experience with fast reactors, adapted to priorities that have evolved markedly from those of the early days of nuclear power. It has four essential, distinguishing features: efficient use of natural resources, inherent safety characteristics, reduced burdens of nuclear waste, and unique proliferation resistance. These fundamental characteristics offer benefits in economics and environmental protection. The fuel cycle never involves separated plutonium, immediately simplifying the safeguarding task. Initiated in 1984 in response to proliferation concerns identified in the International Nuclear Fuel Cycle Evaluation (INFCE, 1980), the project has made substantial technical progress, with new potential applications coming to light as nuclear weapons stockpiles are reduced and concerns about waste disposal increase. A breakthrough technology, the IFR has the characteristics necessary for the next nuclear age. (author)

A Review of the UK Fast Reactor Programme: March 1980

International Nuclear Information System (INIS)

Smith, R.D.

1980-01-01

Towards the end of 1979 the Government announced a new programme of thermal reactor stations to be built over ten years (totalling 15GW), in addition to the two AGR stations at Torness and Heysham 'B' which had been approved by the previous Government. The first station of the new programme will be based on a Westinghouse PWR, subject to safety clearance and the outcome of a public inquiry, and it is envisaged that the remaining stations of the programme would be split between PWRs and AGRs. The AEA Chairman wrote formally to the Secretary of State for Energy in December 1979, putting forward on behalf of the Electricity Supply Authorities, NNC, BNFL and the AEA a recommended strategy for building the Commercial Demonstration Fast Reactor (CDFR), subject to normal licensing procedure and to public inquiry, so as to ensure that the key options for introducing commercial fast reactors, when required, should remain open. A Government statement is expected during the next few months. Meanwhile the level of effort on fast reactor research and development in the UK has been maintained, the fast reactor remaining the largest of the UKAEA's reactor development projects with expenditure totalling somewhat over £80M per annum. The main feature of the UK fast reactor programme has continued to be the operation of PFR (Sections 2 and 7) which is yielding a wealth of experience and of information relevant to the design of commercial fast reactors. Bum-up of standard driver fuel has reached 6-7% by heavy atoms, while specially enriched lead fuel pins have reached 11 % without failure. An extensive programme of work in the reactor and its associated steam plant was completed in March 1980 and the reactor then started its fifth power run. The fuel reprocessing plant at DNE is being commissioned and has reprocessed some of the spent fuel remaining from the DFR. It will start soon on reprocessing fuel discharged from the PFR. During the year improvements to the design of the future

Department of Energy Nuclear Material Protection, Control, and Accounting Program at the Mangyshlak Atomic Energy Complex, Aktau, Republic of Kazakhstan

International Nuclear Information System (INIS)

Case, R.; Berry, R.B.; Eras, A.

1998-01-01

As part of the Cooperative Threat Reduction Nuclear Material Protection, Control, and Accounting (MPC and A) Program, the US Department of Energy and Mangyshlak Atomic Energy Complex (MAEC), Aktau, Republic of Kazakstan have cooperated to enhance existing MAEC MPC and A features at the BN-350 liquid-metal fast-breeder reactor. This paper describes the methodology of the enhancement activities and provides representative examples of the MPC and A augmentation implemented at the MAEC

Economic performance of liquid-metal fast breeder reactor and gas-cooled fast reactor radial blankets

International Nuclear Information System (INIS)

Tsoulfanidis, N.; Jankhah, M.H.

1979-01-01

The economic performance of the radial blanket of a liquid-metal fast breeder reactor (LMFBR) and a gas-cooled fast reactor (GCFR) has been studied based on the calculation of the net financial gain as well as the value of the levelized fuel cost. The necessary reactor physics calculations have been performed using the code CITATION, and the economic analysis has been carried out with the code ECOBLAN, which has been written for that purpose. The residence time of fuel in the blanket is the main variable of the economic analysis. Other parameters that affect the results and that have been considered are the value of plutonium, the price of heat, the effective cost of money, and the holdup time of the spent fuel before reprocessing. The results show that the radial blanket of both reactors is a producer of net positive income for a broad range of values of the parameters mentioned above. The position of the fuel in the blanket and the fuel management scheme applied affect the monetary gain. There is no significant difference between the economic performance of the blanket of an LMFBR and a GCFR

Multi-Functional All BN-BN Composites

Data.gov (United States)

National Aeronautics and Space Administration — Development of multifunctional Boron Nitride nanotube-Boron Nitride (BN-BN) composites to provide novel energy transducers, thermal conductors, anti-penetrator/wear...

A review of the United Kingdom fast reactor program - March 1983

International Nuclear Information System (INIS)

Smith, R.D.

1983-01-01

A review of the United Kingdom Fast Reactor Programme was given in March 1983. Operational experience with the Prototype Fast Reactor (PFR) is briefly summarized. The design concept of the Commercial Demonstration Fast Reactor (CDFR), including design codes, engineering components, materials and fuels development, chemical engineering/sodium technology, safety and reactor performance, is reviewed. The problems of PFR and CDFR fuel reprocessing are also discussed

Development, Fabrication and Characterization of Fuels for Indian Fast Reactor Programme

International Nuclear Information System (INIS)

Kumar, Arun

2013-01-01

Development of Fast Reactor fuels in India started in early Seventies. The successful development of Mixed Carbide fuels for FBTR and MOX fuel for PFBR have given confidence in manufacture of fuels for Fast Reactors. Effort is being put to develop high Breeding Ratio Metallic fuel (binary/ternary). Few fuel pins have been fabricated and is under test irradiation. However, this is only a beginning and complete fuel cycle activities are under development. Metal fuelled Fast Reactors will provide high growth rate in Indian Fast Reactor programme

Irradiation temperature dependence of defect formation of nitrides (A1N and c-BN) during neutron irradiations

International Nuclear Information System (INIS)

Atobe, Kozo.; Okada, Moritami; Nakagawa, Masuo

2000-01-01

The nitrogen vacancy concentration in the more refractory nitrides (A1N and c-BN) is determined as a function of reactor fluence up to 5.2x10 17 thermal neutrons/cm 2 and a function of the irradiation temperature at 25, 50, 100, 150, 200, 250 K. It is found that there is no remarkable dependence of the defect formation in nitrides on the irradiation temperature. The production of damage in the nitrides is considerably different from that in oxides. From the irradiation experiments using thermal neutron irradiation field, it is suggested in reactor irradiation that the atomic displacements in the nitrides occur predominately from energetic particles of the nuclear reactions with thermal neutrons in addition to the elastic collisions by fast neutron

Slow clean-up for fast reactor

Science.gov (United States)

Banks, Michael

2008-05-01

The year 2300 is so distant that one may be forgiven for thinking of it only in terms of science fiction. But this is the year that workers at the Dounreay power station in Northern Scotland - the UK's only centre for research into "fast" nuclear reactors - term as the "end point" by which time the site will be completely clear of radioactive material. More than 180 facilities - including the iconic dome that housed the Dounreay Fast Reactor (DFR) - were built at at the site since it opened in 1959, with almost 50 having been used to handle radioactive material.

A review of fast reactor program in Japan

International Nuclear Information System (INIS)

Matsuno, Y.

1982-01-01

The fast breeder reactor development project in Japan has been in progress for the past twelve months and will be continued this fiscal year, from April 1982 through March 1983, at a similar scale of effort both in budget and personnel to those of the fiscal year of 1981. The 1982 year budget for R and D work and for construction of a prototype fast breeder reactor MONJU is approximately 20 and 27 billion yen respectively, excluding wages for the personnel of the Power Reactor and Nuclear Fuel Development Corporation, PNC. The number of the technical people currently engaged in the fast breeder reactor development in the PNC is approximately 530, excluding those working for plutonium fuel fabrication. Concerning the experimental fast reactor JOYO, power increase from 50 MWt to 75 MWt was made in July 1979 and six operational cycles at 75 MWt were completed in December 1981. With respect to the prototype reactor MONJU, progress toward construction has been made and an environmental impact statement of the reactor was approved by the authorities concerned, and the licensing of the first step was completed at the end of 1981. Preliminary design studies of a large LMFBR are being made by PNC and also by utilities. A design study being conducted by PNC is on a 1000 MWe plant of loop type by extrapolating the technology to be developed by the time of commissioning of MONJU. A group of utilities is conducting a similar study, but covering somewhat wider range of parameters and options of design. Close contact between the group and PNC has been kept. In the future, those design efforts will be combined as a single design effort, when a major effort for developing a large demonstration reactor will be initiated at around the commencement of construction of the prototype reactor MONJU

Technology development of fast reactor fuel reprocessing technology in India

International Nuclear Information System (INIS)

Natarajan, R.; Raj, Baldev

2009-01-01

India is committed to the large scale induction of fast breeder reactors beginning with the construction of 500 MWe Prototype Fast Breeder Reactor, PFBR. Closed fuel cycle is a prerequisite for the success of the fast reactors to reduce the external dependence of the fuel. In the Indian context, spent fuel reprocessing, with as low as possible out of pile fissile inventory, is another important requirement for increasing the share in power generation through nuclear route as early as possible. The development of this complex technology is being carried out in four phases, the first phase being the developmental phase, in which major R and D issues are addressed, while the second phase is the design, construction and operation of a pilot plant, called CORAL (COmpact Reprocessing facility for Advanced fuels in Lead shielded cell. The third phase is the construction and operation of Demonstration of Fast Reactor Fuel Reprocessing Plant (DFRP) which will provide experience in fast reactor fuel reprocessing with high availability factors and plant throughput. The design, construction and operation of the commercial plant (FRP) for reprocessing of PFBR fuel is the fourth phase, which will provide the requisite confidence for the large scale induction of fast reactors

Utilization of MVP for research on fast reactor

International Nuclear Information System (INIS)

Yokoyama, Kenji

2001-01-01

Utilization of the continuous energy Monte-Carlo code, MVP, for research on fast reactor in Power Reactor and Nuclear Fuel Development Corporation(PNC) is described. In this report, three types of utilization are reviewed; (1) a comparison of the eigenvalues calculated by MVP with the results by the deterministic methods, (2) an improvement of U-238 reaction rate evaluation in JUPITER experimental Analysis and (3) an evaluation of heterogeneity effects for Am reaction rates of the moderated subassemblies. Since the results of MVP can be used as references, MVP is very useful code in research on fast reactor. It is one of indispensable tools in order to verify the models in the deterministic methods. Furthermore, it can be used so as to investigate the new concept reactors, such as a reactor aiming to transmute minor actinides(MA). On the other hand, a problem of the variance reduction remains. Especially, a small reactivity cannot be estimated by MVP because of large variances. The development of a Monte-Carlo method for a small reactivity calculation will promote the utilization of MVP for research on fast reactor. (author)

The fifth research coordination meeting (RCM) on 'Updated codes and methods to reduce the calculational uncertainties of liquid metal fast reactors reactivity effects'. Working material

International Nuclear Information System (INIS)

2004-01-01

The general objective of the CRP is to validate, verify and improve methodologies and computer codes used for the calculation of reactivity coefficients in fast reactors aiming at enhancing the utilization of plutonium and minor actinides. The objectives of the fifth RCM were: to review the progress achieved since the 4th RCM; to review and finalize the draft synthesis report on BN-600 MOX Fueled Core Benchmark Analysis (Phase 4); to compare the results of Phase 5 (BFS Benchmark Analysis); to agree on the work scope of Phase 6 (BN-Full MOX Minor Actinide Core Benchmark); to discuss the preparation of the final report. In this context, review and related discussions were made on the following items: summary review of Actions and results since the 4th RCM; finalization of the draft synthesis report on BN-600 full MOX-fueled core benchmark analysis (Phase 4); presentation of individual results for Phase 5 by Member States; preliminary inter-comparison analysis of the results for Phase 5; definition of the benchmark model and work scope to be performed for Phase 6; details of the work scope and future CRP timetable for preparing a final report

Reactivity changes in hybrid thermal-fast reactor systems during fast core flooding

International Nuclear Information System (INIS)

Pesic, M.

1994-09-01

A new space-dependent kinetic model in adiabatic approximation with local feedback reactivity parameters for reactivity determination in the coupled systems is proposed in this thesis. It is applied in the accident calculation of the 'HERBE' fast-thermal reactor system and compared to usual point kinetics model with core-averaged parameters. Advantages of the new model - more realistic picture of the reactor kinetics and dynamics during local large reactivity perturbation, under the same heat transfer conditions, are underlined. Calculated reactivity parameters of the new model are verified in the experiments performed at the 'HERBE' coupled core. The model has shown that the 'HERBE' safety system can shutdown reactor safely and fast even in the case of highly set power trip and even under conditions of big partial failure of the reactor safety system (author)

Status of national programmes on fast breeder reactors. Twenty-fifth annual meeting of the International Working Group on Fast Reactors. Summary report. Working material

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-07-01

At present nuclear power accounts for approximately 17% of total electricity generation worldwide. Given continuing population growth and the needs of the third world and developing countries to improve their economic performance and standard of living, energy demand is expected to continue to grow through the 21st century. The proportion of energy supplied as electricity is also expected to continue to increase. Although fossil fuelled electricity generation is the option preferred by several countries for the short term, there are rising concerns over climatic consequences caused by extended burning of fossil fuels as a result of the demands of a fast expanding world population. In this situation nuclear electricity will become more and more important and the known reserves of uranium would be consumed quite quickly by thermal reactors. It would be possible to sustain a large nuclear programme only by introducing fast reactors. One can conclude that there are strategic reasons for pursuing the development of fast breeder reactors. It will become desirable essential, to have this technology available for introduction. The experience of the various prototypes presently in operation has confirmed the operability and benign characteristics of the LMFR and has given ground for confidence in the future. Current fast reactor designs offer very large margins of safety and by virtue of redundant and diverse safety systems the potential for an energetic core disruptive accident or for fast reactor core meltdown has been essentially eliminated. Several international forums reviewed the current trends in the fast reactor development. The view was reaffirmed that fast breeder reactors still remain the most practical tool for effective utilization of uranium resources for the future energy needs. Achievement of competitiveness with LMRs is still the first priority condition for the future deployment of this type of reactor. The recycling of plutonium into LMFBRs would allow

Status of national programmes on fast breeder reactors. Twenty-fifth annual meeting of the International Working Group on Fast Reactors. Summary report. Working material

International Nuclear Information System (INIS)

1992-01-01

At present nuclear power accounts for approximately 17% of total electricity generation worldwide. Given continuing population growth and the needs of the third world and developing countries to improve their economic performance and standard of living, energy demand is expected to continue to grow through the 21st century. The proportion of energy supplied as electricity is also expected to continue to increase. Although fossil fuelled electricity generation is the option preferred by several countries for the short term, there are rising concerns over climatic consequences caused by extended burning of fossil fuels as a result of the demands of a fast expanding world population. In this situation nuclear electricity will become more and more important and the known reserves of uranium would be consumed quite quickly by thermal reactors. It would be possible to sustain a large nuclear programme only by introducing fast reactors. One can conclude that there are strategic reasons for pursuing the development of fast breeder reactors. It will become desirable essential, to have this technology available for introduction. The experience of the various prototypes presently in operation has confirmed the operability and benign characteristics of the LMFR and has given ground for confidence in the future. Current fast reactor designs offer very large margins of safety and by virtue of redundant and diverse safety systems the potential for an energetic core disruptive accident or for fast reactor core meltdown has been essentially eliminated. Several international forums reviewed the current trends in the fast reactor development. The view was reaffirmed that fast breeder reactors still remain the most practical tool for effective utilization of uranium resources for the future energy needs. Achievement of competitiveness with LMRs is still the first priority condition for the future deployment of this type of reactor. The recycling of plutonium into LMFBRs would allow

UK fast reactor components - sodium removal decontamination and requalification

Energy Technology Data Exchange (ETDEWEB)

Donaldson, D M [FRDD, UKAEA, Risley (United Kingdom); Bray, J A; Newson, I H [UKAEA, Dounreay Nuclear Power Establishment, Thurso (United Kingdom)

1978-08-01

Over the past two decades extensive experience on sodium removal techniques has been gained at the UKAEA's Dounreay Nuclear Establishment from both the Dounreay Fact Reactor (DFR) and the Prototype Fast Reactor (PFR). This experience has created confidence that complex components can be cleaned of sodium, maintenance or repair operations carried out, and the components successfully re-used. Part 2 of the paper, which describes recent operations associated with the PFR, demonstrates the background to these views. This past and continuing experience is being used in forming the basis of the plant to be provided for sodium removal, decontamination and requalification of components in the UK's future commercial fast reactors. Further improvements in techniques and in component designs can be expected in the course of the next few years. Consequently UK philosophy and approach with respect to maintenance and repair operations is sufficiently flexible to enable relevant improvements to be incorporated into the next scheduled fast reactor - the Commercial Demonstration Fast Reactor (CUR). This paper summarises the factors which are being taken into consideration in this continuously advancing field.

UK fast reactor components - sodium removal decontamination and requalification

International Nuclear Information System (INIS)

Donaldson, D.M.; Bray, J.A.; Newson, I.H.

1978-01-01

Over the past two decades extensive experience on sodium removal techniques has been gained at the UKAEA's Dounreay Nuclear Establishment from both the Dounreay Fact Reactor (DFR) and the Prototype Fast Reactor (PFR). This experience has created confidence that complex components can be cleaned of sodium, maintenance or repair operations carried out, and the components successfully re-used. Part 2 of the paper, which describes recent operations associated with the PFR, demonstrates the background to these views. This past and continuing experience is being used in forming the basis of the plant to be provided for sodium removal, decontamination and requalification of components in the UK's future commercial fast reactors. Further improvements in techniques and in component designs can be expected in the course of the next few years. Consequently UK philosophy and approach with respect to maintenance and repair operations is sufficiently flexible to enable relevant improvements to be incorporated into the next scheduled fast reactor - the Commercial Demonstration Fast Reactor (CUR). This paper summarises the factors which are being taken into consideration in this continuously advancing field

Proceedings of 'workshop on Pb-alloy cooled fast reactor'

International Nuclear Information System (INIS)

Kim, Sang Ji; Kim, Yong Hee; Hong, Ser Gi

2003-06-01

The objective of 'Workshop on Pb-Alloy Cooled Fast Reactor', held in Taejeon, Korea on May 6, 2003, is to enhance the basic knowledge in this area by facilitating the exchange of information and discussions about problematic area of design aspects. There were five presentations from three different countries and about 25 participants gathered during the workshop. The topics covered in the workshop include benefits and drawbacks of Pb-alloy and Sodium coolant, two Pb-alloy cooled 900 MWt reactor designs using both B4C rods and NSTs, BREST-300 breakeven reactor and transmutation effectiveness of LLFPs in the typical thermal/fast neutron systems. The generic conclusion for the Pb-alloy cooled fast reactor from this workshop is as follows: 1) It has a potential to satisfy the goals established for the Generation-IV reactor concepts, so it has a bright future. 2) As a fast neutron system with a moderate breeding or a conversion, it is flexible in its roles and has superior safety characteristics over sodium coolant because of Pb-alloy's chemical inertness with water/air and high boiling temperature

International Working Group on Fast Reactors Second Annual Meeting. Summary Report

International Nuclear Information System (INIS)

1969-01-01

The Agenda of the Meeting was as follows: Opening of the meeting. 2. Appraisal of the IWGFB's activity for the period from the first annual meeting of the Group. 3. Comments on national programmes on fast breeder reactors. 4. Presentation of general findings and conclusions of national and regional meetings on fast reactor problems held in represented countries and international organisations last year. 5. Comments on the programmes of international meetings on fast reactors to be held in 1969. 6. Consideration of a schedule for meetings on fast reactors in 1970. 7. Suggestions for the topics and location of specialists' meetings in 1969-1970. 8. Suggestions for reviews and studies in the field of fast reactors. 9. The time and place of the third annual meeting of the IWGFR. 10. Closing of the meeting

Trends and Developments for Fast Neutron Reactors and Related Fuel Cycles

International Nuclear Information System (INIS)

Carré, Frank

2013-01-01

• FR13 – A unique and dedicated framework to share updates on national programs of Fast Reactor developments, projects of new builds and plans for the future: - Near term projects of sodium and lead-alloy Fast Reactors; - Gen-IV visions of sodium-cooled and alternative types of Fast Neutron Reactors (GFR, LFR…). • FR13 – A special emphasis put on Fast Reactor Safety, Sustainability of nuclear fuel cycle and Young Generation perspective. • FR13 – A catalyst for further collaborations and alliances: - To share visions of goals and advisable options for future Fast Reactors and Nuclear Fuel Cycle; - To share cost of R&D and large demonstrations (safety, security, recycling); - To progress towards harmonized international standards; - To integrate national projects into a consistent international roadmap

The fast breeder reactor Rapsodie (1962)

International Nuclear Information System (INIS)

Vautrey, L.; Zaleski, C.P.

1962-01-01

In this report, the authors describe the Rapsodie project, the French fast breeder reactor, as it stands at construction actual start-up. The paper provides informations about: the principal neutronic and thermal characteristics, the reactor and its cooling circuits, the main handling devices of radioactive or contaminated assemblies, the principles and means governing reactor operation, the purposes and locations of miscellaneous buildings. Rapsodie is expected to be critical by 1964. (authors) [fr

The development of accurate data for the desing of fast reactors

International Nuclear Information System (INIS)

Rossouw, P.A.

1976-04-01

The proposed use of nuclear power in the generation of electricity in South Africa and the use of fast reactors in the country's nuclear porgram, requires a method for fast reactor evluation. The availability of accurate neutron data and neutronics computation techniques for fast reactors are required for such an evaluation. The reacotr physics and reactor parameters of importance in the evaluation of fast reacotrs are discussed, and computer programs for the computation of reactor spectra and reacotr parameters from differential nuclear data are presented in this treatise. In endeavouring to increase the accuracy in fast reactor design, two methods for the improvement of differential nuclear data were developed and are discussed in detail. The computer programs which were developed for this purpose are also given. The neutron data of the most important fissionable and breeding nuclei (U 235 x U 238 x Pu 239 and Pu 240 ) are adjusted using both methods and the improved neutron data are tested by computation with an advanced neutronics computer program. The improved and orginal neutron data are compared and the use of the improved data in fast reactor design is discussed

Implications of nuclear physics in the development of Fast Breeder Reactors

International Nuclear Information System (INIS)

Rapeanu, S.; Ilie, P.; Vasiliu, G.; Popescu, C.; Boeriu, S.; Constantinescu, D.; Mateescu, S.

1980-08-01

The purpose of this paper is to point out the involved aspects of nuclear physics in the calculation and design of the fast reactors. After a brief description of the advantages of using the fast reactors in the national economy, the national programs concerning this activity are presented. The structure and operation conditions of the liquid metal fast breeder reactor (LMFBR) are also reviewed. Then, the methods aimed to calculate the core, the burn-up, the reactor dynamics, the analysis of accidents, the shielding, as well as, the materials required in the fast reactor calculation, are shortly given. Further on, it deals with the nuclear data types connected to the fast reactor calculations, with accuracy requirements for nuclear data, as well as, with the present stage of nuclear data for fissile, fertile and structural materials. The requirements for new differential data measurements, new integral data and benchmark experiments are presented. Data adjustement methods are also summarized. Some aspects of the structural material behaviour in intense gamma radiation and neutron fields existing into a fast reactor are also presented in the last part of this paper. The concluding remarks are mentioned at the end of the paper. (author)

Nuclear Burning Wave Modular Fast Reactor Concept

International Nuclear Information System (INIS)

Kodochigov, N.G.; Sukharev, Yu.P.

2014-01-01

The necessity to provide nuclear power industry, comparable in a scope with power industry based on a traditional fuel, inspired studies of an open-cycle fast reactor aimed at: - solution of the problem of fuel provision by implementing the highest breeding characteristics of new fissile materials of raw isotopes in a fast reactor and applying accumulated fissile isotopes in the same reactor, independently on a spent fuel reprocessing rate in the external fuel cycle; - application of natural or depleted uranium for makeup fuel, which, with no spent fuel reprocessing, forms the most favorable non-proliferation conditions; - application of inherent properties of the core and reactor for safety provision. The present report, based on previously published papers, gives the theoretical backgrounds of the concept of the reactor with a nuclear burning wave, in which an enriched-fuel core (driver) is replaced by a blanket, and basic conditions for nuclear burning wave initiating and keeping are shown. (author)

A worldwide survey of fast breeder reactors

International Nuclear Information System (INIS)

Hennies, H.H.

1986-01-01

While the completion of the SNR 300 was accompanied by manifold discussions on questions relevant to safety and energy policies in the Federal Republic of Germany and as a result considerable scheduling delays and exceeding of budgets were recorded, breeder reactor technology has been progressing worldwide. The transition from the development phase with small trial reactors to the construction and operation of large performance reactors was completed systematically, in particular in France and the Soviet Union. Even though the uranium supply situation does not make a short-term and comprehensive employment of fast breeder reactors essential, technology has meanwhile been advanced to such a level and extensive operating experience is on hand to enable the construction and safe operation of fast breeder reactors. A positive answer has long been found to the question of the realization of a breeding rate to guarantee the breeding effect. There remain now the endeavors to achieve a reduction in investment and fuel cycle costs. (orig.) [de

Progress in liquid metal fast reactor technology. Proceedings of the 28th meeting of the International Working Group on Fast Reactors

International Nuclear Information System (INIS)

1996-04-01

The key objectives and activities of Member State liquid metal fast reactor (LMFR) programmes are: Demonstration of effective designs; demonstration of system safety; demonstration of economic competitiveness with other power generation systems. The International Working Group on Fast Reactors (IWGFR) at its 1995 meeting observed that while some countries (as a result of static or falling power demand) are reducing the research and development programmes or delaying the commercial deployment of fast reactors, other countries are planning to introduce these reactors and are embarking on their own development programmes. In these circumstances the international exchange of information and experience is of increasing importance. These proceedings contain updated information from long standing members of the IWGFR and new information on the status of LMFR research and development from new members of the Group: Brazil, China, Republic of Kazakhstan and the Republic of Korea. Refs, figs, tabs

Progress in liquid metal fast reactor technology. Proceedings of the 28th meeting of the International Working Group on Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

The key objectives and activities of Member State liquid metal fast reactor (LMFR) programmes are: Demonstration of effective designs; demonstration of system safety; demonstration of economic competitiveness with other power generation systems. The International Working Group on Fast Reactors (IWGFR) at its 1995 meeting observed that while some countries (as a result of static or falling power demand) are reducing the research and development programmes or delaying the commercial deployment of fast reactors, other countries are planning to introduce these reactors and are embarking on their own development programmes. In these circumstances the international exchange of information and experience is of increasing importance. These proceedings contain updated information from long standing members of the IWGFR and new information on the status of LMFR research and development from new members of the Group: Brazil, China, Republic of Kazakhstan and the Republic of Korea. Refs, figs, tabs.

Fuel component of electricity generation cost for the BN-800 reactor with 800 MOX fuel and uranium oxide fuel, increased fuel burnup, and removal of radial breeding blanket

International Nuclear Information System (INIS)

Raskach, A.

2000-01-01

There are two completed design concepts of NPP with BN-800 type reactors developed with due regard for enhanced safety requirements. They have been created for the 3 rd unit of Beloyarsk NPP and for three units of South Ural NPP. Both concepts are proposed to use mixed oxide fuel (MOX) based on civil plutonium. At this moment economical estimations carried out for these projects need to be revised in connection with the changes of economical situation in Russia and the world nuclear market structure. It is also essential to take into account the existing problem of the excess ex-weapons plutonium utilization and the possibility of using this plutonium to fabricate MOX fuel for the BN-800 reactors. (authors)

Fuel Development For Gas-Cooled Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

M. K. Meyer

2006-06-01

The Generation IV Gas-cooled Fast Reactor (GFR) concept is proposed to combine the advantages of high-temperature gas-cooled reactors (such as efficient direct conversion with a gas turbine and the potential for application of high-temperature process heat), with the sustainability advantages that are possible with a fast-spectrum reactor. The latter include the ability to fission all transuranics and the potential for breeding. The GFR is part of a consistent set of gas-cooled reactors that includes a medium-term Pebble Bed Modular Reactor (PBMR)-like concept, or concepts based on the Gas Turbine Modular Helium Reactor (GT-MHR), and specialized concepts such as the Very High Temperature Reactor (VHTR), as well as actinide burning concepts [ ]. To achieve the necessary high power density and the ability to retain fission gas at high temperature, the primary fuel concept proposed for testing in the United States is a dispersion coated fuel particles in a ceramic matrix. Alternative fuel concepts considered in the U.S. and internationally include coated particle beds, ceramic clad fuel pins, and novel ceramic ‘honeycomb’ structures. Both mixed carbide and mixed nitride-based solid solutions are considered as fuel phases.

Flexible Conversion Ratio Fast Reactor Systems Evaluation

Energy Technology Data Exchange (ETDEWEB)

Neil Todreas; Pavel Hejzlar

2008-06-30

Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. Both concepts have cores reated at 2400 MWt placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchanges coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced Reactor Vessel Auxiliary Cooling System and a Passive Secondary Auxiliary Cooling System. The most important findings were that (1) it is feasible to design the lead-cooled and salt-cooled reactor with the flexible conversion ratio (CR) in the range of CR=0 and CR=1 n a manner that achieves inherent reactor shutdown in unprotected accidents, (2) the salt-cooled reactor requires Lithium thermal Expansion Modules to overcme the inherent salt coolant's large positive coolant temperature reactivity coefficient, (3) the preferable salt for fast spectrum high power density cores is NaCl-Kcl-MgCl2 as opposed to fluoride salts due to its better themal-hydraulic and neutronic characteristics, and (4) both reactor, but attain power density 3 times smaller than that of the sodium-cooled reactor.

Flexible Conversion Ratio Fast Reactor Systems Evaluation

International Nuclear Information System (INIS)

Neil Todreas; Pavel Hejzlar

2008-01-01

Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. Both concepts have cores treated at 2400 MWt placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchanges coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced Reactor Vessel Auxiliary Cooling System and a Passive Secondary Auxiliary Cooling System. The most important findings were that (1) it is feasible to design the lead-cooled and salt-cooled reactor with the flexible conversion ratio (CR) in the range of CR=0 and CR=1 n a manner that achieves inherent reactor shutdown in unprotected accidents, (2) the salt-cooled reactor requires Lithium thermal Expansion Modules to overcome the inherent salt coolant's large positive coolant temperature reactivity coefficient, (3) the preferable salt for fast spectrum high power density cores is NaCl-Kcl-MgCl2 as opposed to fluoride salts due to its better thermal-hydraulic and neutronic characteristics, and (4) both reactor, but attain power density 3 times smaller than that of the sodium-cooled reactor

Intrinsically secure fast reactors with dense cores

International Nuclear Information System (INIS)

Slessarev, Igor

2007-01-01

Secure safety, resistance to weapons material proliferation and problems of long-lived wastes remain the most important 'painful points' of nuclear power. Many innovative reactor concepts have been developed aimed at a radical enhancement of safety. The promising potential of innovative nuclear reactors allows for shifting accents in current reactor safety 'strategy' to reveal this worth. Such strategy is elaborated focusing on the priority for intrinsically secure safety features as well as on sure protection being provided by the first barrier of defence. Concerning the potential of fast reactors (i.e. sodium cooled, lead-cooled, etc.), there are no doubts that they are able to possess many favourable intrinsically secure safety features and to lay the proper foundation for a new reactor generation. However, some of their neutronic characteristics have to be radically improved. Among intrinsically secure safety properties, the following core parameters are significantly important: reactivity margin values, reactivity feed-back and coolant void effects. Ways of designing intrinsically secure safety features in fast reactors (titled hereafter as Intrinsically Secure Fast Reactors - ISFR) can be found in the frame of current reactor technologies by radical enhancement of core neutron economy and by optimization of core compositions. Simultaneously, respecting resistance to proliferation, by using non-enriched fuel feed as well as a core breeding gain close to zero, are considered as the important features (long-lived waste problems will be considered in a separate paper). This implies using the following reactor design options as well as closed fuel cycles with natural U as the reactor feed: ·Ultra-plate 'dense cores' of the ordinary (monolithic) type with negative total coolant void effects. ·Modular type cores. Multiple dense modules can be embedded in the common reflector for achieving the desired NPP total power. The modules can be used also independently (as

Status of fast reactor activities in Brazil

International Nuclear Information System (INIS)

Menezes, Artur

1996-01-01

This text describes the present status of fast reactor activities in Brazil, emphasizing the strategies being used to preserve this reactor concept as a viable alternative for future electricity generation in the country. The program is mostly research-oriented and has the objective of establishing a consistent knowledge basis which can serve as a support for the transition to the activities more directly related to design, construction and operation of an experimental fast reactor. Due to the present economic difficulties, the program is still modest but it is gradually growing. A report which has been finalized in December, 1995 and submitted to the authorities indicates the existence of the grounds for enlarging and consolidating the program. (author)

Development of the IAEA’s Knowledge Preservation Portals for Fast Reactors and Gas-Cooled Reactors Knowledge Preservation

International Nuclear Information System (INIS)

Batra, C.; Menahem, D. Beraha; Kriventsev, V.; Monti, S.; Reitsma, F.; Grosbois, J. de; Khoroshev, M.; Gladyshev, M.

2016-01-01

Full text: The IAEA has been carrying out a dedicated initiative on fast reactor knowledge preservation since 2003. The main objectives of the Fast Reactor Knowledge Portal (FRKP) initiative are to, a) halt the on-going loss of information related to fast reactors (FR), and b) collect, retrieve, preserve and make accessible existing data and information on FR. This portal will help in knowledge sharing, development, search and discovery, collaboration and communication of fast reactor related information. On similar lines a Gas Cooled Fast Reactor Knowledge Preservation portal project also started in 2013. Knowledge portals are capable to control and manage both publicly available as well as controlled information. The portals will not only incorporate existing set of knowledge and information, but will also provide a systemic platform for further preservation of new developments. It will include fast reactor and gas cooled reactor document repositories, project workspaces for the IAEA’s Coordinated Research Projects (CRPs), Technical Meetings (TMs), forums for discussion, etc. The portal will also integrate a taxonomy based search tool, which will help using new semantic search capabilities for improved conceptual retrieve of documents. The taxonomy complies with international web standards as defined by the W3C (World Wide Web Consortium). (author

Programme and current status of fast breeder reactor development in Japan

International Nuclear Information System (INIS)

Suita, T.; Oyama, A.

1977-01-01

In 1967 the Japan Atomic Energy Commission revised her long term programme after a two year study for giving principles to her nuclear energy development programme, which indicated the dominant role of nuclear energy mid 1980's in the electric power generation and stressed the necessity of developing fast breeder reactors. It also recommended to organize a nucleus to undertake this nation-wide project, bringing together the total capability available throughout the country. Accordingly, the Power Reactor and Nuclear Fuel Development Corporation (PNC) was established in 1967 to develop two sodium-cooled fast reactors, an experimental fast reactor of about 100 MW thermal and a prototype fast breeder reactor of about 300 MW electrical, both using mixed oxide fuels. Construction of the experimental fast reactor started in 1970 and was essentially completed at the end of in 1974. The precommissioning test was followed in parallel with re-evaluating quality assurance of all systems. Physics test will be initiated around the end of 1976. The conceptual design of the prototype fast breeder reactor is now toward its final stage. Surveys on its proposed site have just started. Construction will start in 1978. Beside R and D works conducted by many organizations in Japan as well as under the international cooperation, several key test facilities were installed by PNC itself to conduct in-sodium test of full-size prototype components including 50 MW steam generators and post-irradiation-examination of fuels and materials. Recently an interim report was issued to an ad-hoc committee organized by JAEC to evaluate future prospect of the fuel cycle and power reactors. This recommended start of construction of the prototype reactor as scheduled and the large demonstration reactor to be followed to the prototype. Thus the fast breeder reactor is indicated as the most indispensable in 1990's

The computerized reactor period measurement system for China fast burst reactor-II

International Nuclear Information System (INIS)

Zhao Wuwen; Jiang Zhiguo

1996-01-01

The article simply introduces the hardware, principle, and software of the computerized reactor period measurement system for China Fast Burst Reactor-II (CFBR-II). It also gives the relation between fission yield and pre-reactivity of CFBR-II reactor system of bared reactor with decoupled-component and system of bared reactor with multiple light-material. The computerized measurement system makes the reactor period measurement into automatical and intelligent and also improves the speed and precision of period data on-line process

Computer measurement system of reactor period for China fast burst reactor-II

International Nuclear Information System (INIS)

Zhao Wuwen; Jiang Zhiguo

1997-01-01

The author simply introduces the hardware, principle, and software of the reactor period computer measure system for China Fast Burst Reactor-II (CFBR-II). It also gives the relation between Fission yield and Pre-reactivity of CFBR-II reactor system of bared reactor with decoupled-component and system of bared reactor with multiple light-material. The computer measure system makes the reactor period measurement into automation and intellectualization and also improves the speed and precision of period data process on-line

Fast reactor development strategy targets study in China

International Nuclear Information System (INIS)

Xu Mi

2008-01-01

China is a big developing Country who needs a huge energy resources and a rapid growing rate. Considering energy resources limited and environment issues it is sure that the nuclear energy will be becoming one of the main energy resources. The Government has decided to develop the nuclear power capacity to 40 GW in 2020. It is envisaged that it will reach to 240 GW in 2050. It is stimulate us to consider conscientiously the development of the fast breeder reactor's and related closed nuclear fuel cycle by the limitation of Uranium resources and uncertainties of international Uranium market. Followings are the proposed strategic targets of fast reactor development in China. (1) To realize the operation of commercial fast breeder reactors with an unit size of 800-900 MWe and one site-multi reactors in 2030. (2) To develop the nuclear power capacity to 240 GW in 2050. (3) To replace step by step the fossil fuel utilization in large scale by nuclear energy beyond 2050. (authors)

Comparative assessment of nuclear fuel cycles. Light-water reactor once-through, classical fast breeder reactor, and symbiotic fast breeder reactor cycles

International Nuclear Information System (INIS)

Hardie, R.W.; Barrett, R.J.; Freiwald, J.G.

1980-06-01

The object of the Alternative Nuclear Fuel Cycle Study is to perform comparative assessments of nuclear power systems. There are two important features of this study. First, this evaluation attempts to encompass the complete, integrated fuel cycle from mining of uranium ore to disposal of waste rather than isolated components. Second, it compares several aspects of each cycle - energy use, economics, technological status, proliferation, public safety, and commercial potential - instead of concentrating on one or two assessment areas. This report presents assessment results for three fuel cycles. These are the light-water reactor once-through cycle, the fast breeder reactor on the classical plutonium cycle, and the fast breeder reactor on a symbiotic cycle using plutonium and 233 U as fissile fuels. The report also contains a description of the methodology used in this assessment. Subsequent reports will present results for additional fuel cycles

Breeding description for fast reactors and symbiotic reactor systems

International Nuclear Information System (INIS)

Hanan, N.A.

1979-01-01

A mathematical model was developed to provide a breeding description for fast reactors and symbiotic reactor systems by means of figures of merit type quantities. The model was used to investigate the effect of several parameters and different fuel usage strategies on the figures of merit which provide the breeding description. The integrated fuel cycle model for a single-reactor is reviewed. The excess discharge is automatically used to fuel identical reactors. The resulting model describes the accumulation of fuel in a system of identical reactors. Finite burnup and out-of-pile delays and losses are treated in the model. The model is then extended from fast breeder park to symbiotic reactor systems. The asymptotic behavior of the fuel accumulation is analyzed. The asymptotic growth rate appears as the largest eigenvalue in the solution of the characteristic equations of the time dependent differential balance equations for the system. The eigenvector corresponding to the growth rate is the core equilibrium composition. The analogy of the long-term fuel cycle equations, in the framework of this model, and the neutron balance equations is explored. An eigenvalue problem adjoint to the one generated by the characteristic equations of the system is defined. The eigenvector corresponding to the largest eigenvalue, i.e. to the growth rate, represents the ''isotopic breeding worths.'' Analogously to the neutron adjoint flux it is shown that the isotopic breeding worths represent the importance of an isotope for breeding, i.e. for the growth rate of a system

Comparison of the worth of control and protection system rods of different design on the basis of the measurements in BN-600 reactor

International Nuclear Information System (INIS)

Vasilyev, B.A.; Roslyakov, V.F.; Farakshin, M.R.

1988-01-01

The results of the worth measurements of the basic and experimental absorbing rods of BN-600 reactor are presented. The procedure used for the rods worth comparison on the basis of calculated and experimental data interpretation is described here. Basic and experimental rods relative worth is also presented. (author). 5 refs, 3 figs, 2 tabs

Pressure sensing element based on the BN-graphene-BN heterostructure

Science.gov (United States)

Li, Mengwei; Wu, Chenggen; Zhao, Shiliang; Deng, Tao; Wang, Junqiang; Liu, Zewen; Wang, Li; Wang, Gao

2018-04-01

In this letter, we report a pressure sensing element based on the graphene-boron nitride (BN) heterostructure. The heterostructure consists of monolayer graphene sandwiched between two layers of vertically stacked dielectric BN nanofilms. The BN layers were used to protect the graphene layer from oxidation and pollution. Pressure tests were performed to investigate the characteristics of the BN-graphene-BN pressure sensing element. A sensitivity of 24.85 μV/V/mmHg is achieved in the pressure range of 130-180 kPa. After exposing the BN-graphene-BN pressure sensing element to the ambient environment for 7 days, the relative resistance change in the pressure sensing element is only 3.1%, while that of the reference open-faced graphene device without the BN protection layers is 15.7%. Thus, this strategy is promising for fabricating practical graphene pressure sensors with improved performance and stability.

Conceptual design of a fast-ignition laser fusion reactor based on a dry wall chamber

International Nuclear Information System (INIS)

Ogawa, Y; Goto, T; Okano, K; Asaoka, Y; Hiwatari, R; Someya, Y

2008-01-01

The fast ignition is quite attractive for a compact laser fusion reactor, because a sufficiently high pellet gain is available with a small input energy. We designed an inertial fusion reactor based on Fast-ignition Advanced Laser fusion reactor CONcept, called FALCON-D, where a dry wall is employed for a chamber wall. A simple point model shows that the pellet gain G∼100 is available with laser energies of 350kJ for implosion, 50kJ for heating. This results in the fusion yield of 40 MJ in one shot. By increasing the repetition rate up to 30 Hz, the fusion power of 1.2 GWth becomes available. Plant system analysis shows the net electric power to be about 0.4 GWe In the fast ignition it is available to employ a low aspect ratio pellet, which is favorable for the stability during the implosion phase. Here the pellet aspect ratio is reduced to be 2 ∼ 4, and the optimization of the pulse shape for the implosion laser are carried out by using the 1-D hydrodynamic simulation code ILESTA-1D. A ferritic steel with a tungsten armour is employed for the chamber wall. The feasibility of this dry wall concept is studied from various engineering aspects such as surface melting, physical and chemical sputtering, blistering and exfoliation by helium retention, and thermo-mechanical fatigue, and it is found that blistering and exfoliation due to the helium retention and fatigue failure due to cyclic thermal load are major concerns. The cost analysis shows that the construction cost is moderate but the cost of electricity is slightly expensive

Conceptual design of a fast-ignition laser fusion reactor based on a dry wall chamber

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Y [High Temperature Plasma Center, University of Tokyo, Chiba (Japan); Goto, T; Okano, K [Graduate School of Frontier Sciences, University of Tokyo, Chiba (Japan); Asaoka, Y; Hiwatari, R [Central Research Institute for Electric Power Industry, Komae, Tokyo (Japan); Someya, Y [Graduate School of Engineering, Musashi Institute of Technology, Tokyo (Japan)], E-mail: ogawa@ppl.k.u-tokyo.ac.jp

2008-05-15

The fast ignition is quite attractive for a compact laser fusion reactor, because a sufficiently high pellet gain is available with a small input energy. We designed an inertial fusion reactor based on Fast-ignition Advanced Laser fusion reactor CONcept, called FALCON-D, where a dry wall is employed for a chamber wall. A simple point model shows that the pellet gain G{approx}100 is available with laser energies of 350kJ for implosion, 50kJ for heating. This results in the fusion yield of 40 MJ in one shot. By increasing the repetition rate up to 30 Hz, the fusion power of 1.2 GWth becomes available. Plant system analysis shows the net electric power to be about 0.4 GWe In the fast ignition it is available to employ a low aspect ratio pellet, which is favorable for the stability during the implosion phase. Here the pellet aspect ratio is reduced to be 2 {approx} 4, and the optimization of the pulse shape for the implosion laser are carried out by using the 1-D hydrodynamic simulation code ILESTA-1D. A ferritic steel with a tungsten armour is employed for the chamber wall. The feasibility of this dry wall concept is studied from various engineering aspects such as surface melting, physical and chemical sputtering, blistering and exfoliation by helium retention, and thermo-mechanical fatigue, and it is found that blistering and exfoliation due to the helium retention and fatigue failure due to cyclic thermal load are major concerns. The cost analysis shows that the construction cost is moderate but the cost of electricity is slightly expensive.

Conceptual design of a fast-ignition laser fusion reactor based on a dry wall chamber

Science.gov (United States)

Ogawa, Y.; Goto, T.; Okano, K.; Asaoka, Y.; Hiwatari, R.; Someya, Y.

2008-05-01

The fast ignition is quite attractive for a compact laser fusion reactor, because a sufficiently high pellet gain is available with a small input energy. We designed an inertial fusion reactor based on Fast-ignition Advanced Laser fusion reactor CONcept, called FALCON-D, where a dry wall is employed for a chamber wall. A simple point model shows that the pellet gain G~100 is available with laser energies of 350kJ for implosion, 50kJ for heating. This results in the fusion yield of 40 MJ in one shot. By increasing the repetition rate up to 30 Hz, the fusion power of 1.2 GWth becomes available. Plant system analysis shows the net electric power to be about 0.4 GWe In the fast ignition it is available to employ a low aspect ratio pellet, which is favorable for the stability during the implosion phase. Here the pellet aspect ratio is reduced to be 2 ~ 4, and the optimization of the pulse shape for the implosion laser are carried out by using the 1-D hydrodynamic simulation code ILESTA-1D. A ferritic steel with a tungsten armour is employed for the chamber wall. The feasibility of this dry wall concept is studied from various engineering aspects such as surface melting, physical and chemical sputtering, blistering and exfoliation by helium retention, and thermo-mechanical fatigue, and it is found that blistering and exfoliation due to the helium retention and fatigue failure due to cyclic thermal load are major concerns. The cost analysis shows that the construction cost is moderate but the cost of electricity is slightly expensive.

Research on the usage of a deep sea fast reactor

Energy Technology Data Exchange (ETDEWEB)

Otsubo, Akira; Kowata, Yasuki [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1997-09-01

Many new types of fast reactors have been studied in PNC. A deep sea fast reactor has the highest realization probability of the reactors studied because its development is desired by many specialists of oceanography, meteorology, deep sea bottom oil field, seismology and so on and because the development does not cost big budget and few technical problems remain to be solved. This report explains the outline and the usage of the reactor of 40 kWe and 200 to 400 kWe. The reactor can be used as a power source at an unmanned base for long term climate prediction and the earth science and an oil production base in a deep sea region. On the other hand, it is used for heat and electric power supply to a laboratory in the polar region. In future, it will be used in the space. At the present time, a large FBR development plan does not proceed successfully and a realization goal time of FBR has gone later and later. We think that it is the most important to develop the reactor as fast as possible and to plant a fast reactor technique in our present society. (author)

A review of fast reactor program in Japan

International Nuclear Information System (INIS)

1996-01-01

The main R and D results of Japanese activities are summarized as follows: (1) the experimental 140 MW(th) sodium cooled fast reactor 'Joyo' provided abundant experimental data and excellent operational records, attaining more than 50,000 hours of operation since its first criticality in 1977; (2) the prototype 280 MW(e) fast reactor 'Monju' reached initial criticality on 5 April 1994; presently Monju is under the cold shutdown state because of secondary sodium leak on 8 December 1995, and multiple cause investigations of the sodium leak are being performed; (3) the Japan Atomic Power Company is promoting design studies for demonstration fast reactor (DFBR) with a power output of 600 MW(e) and R and D for DFBR are being conducted under the cooperation of governmental and private sectors. (author)

Estimation of the radiation risks for population in the process of the BN-600 power unit operation at the Beloyarsk NPP

International Nuclear Information System (INIS)

Koltik, I.I.; Oshkanov, N.N.

2005-01-01

Dose burdens on the population are the main criterion in estimating the radiological risks during NPP operation. Results of analysis of annual dose burdens on the population in the period of the BN-600 unit operation are presented. Data on individual and collective doses due to gas-aerosol and liquid effluents of radionuclides from the BN-600 unit on critical groups of population are presented. Data on collective doses due to other types of reactors are provided. It is shown that the risks stemming from the BN type reactors are approximately 2 orderers below the risks of channel-type and WWER-reactors [ru

The problems of thermohydraulics of prospective fast reactor concepts

International Nuclear Information System (INIS)

Sedov, A.A.

2000-01-01

In this report the main requirements to fast reactors in system of future multicomponent Nuclear Power with closed U-Pu fuel cycle are regarded. The peculiarities of different liquid-metal (sodium and lead-alloyed) coolants as well as the thermohydraulics problems of prospective fast reactors (FR) concepts are discussed. (author)

The Integral Fast Reactor (IFR) concept

International Nuclear Information System (INIS)

Till, C.E.; Chang, Y.I.

1989-01-01

In addition to maintaining the viability of its present commercial nuclear technology, a principal challenge in the US in the 1990s and beyond will be to regain and maintain a position among the world leadership in advanced reactor research and development. In this paper we'll discuss factors which we believe should today provide the rationale and focus for advanced reactor R and D, and we will then review the status of the major US effort, the Integral Fast Reactor (IFR) program

Use of fast reactors for actinide transmutation

International Nuclear Information System (INIS)

1993-03-01

The management of radioactive waste is one of the key issues in today's discussions on nuclear energy, especially the long term disposal of high level radioactive wastes. The recycling of plutonium in liquid metal fast breeder reactors (LMFBRs) would allow 'burning' of the associated extremely long life transuranic waste, particularly actinides, thus reducing the required isolation time for high level waste from tens of thousands of years to hundreds of years for fission products only. The International Working Group on Fast Reactors (IWGFR) decided to include the topic of actinide transmutation in liquid metal fast breeder reactors in its programme. The IAEA organized the Specialists Meeting on Use of Fast Breeder Reactors for Actinide Transmutation in Obninsk, Russian Federation, from 22 to 24 September 1992. The specialists agree that future progress in solving transmutation problems could be achieved by improvements in: Radiochemical partitioning and extraction of the actinides from the spent fuel (at least 98% for Np and Cm and 99.9% for Pu and Am isotopes); technological research and development on the design, fabrication and irradiation of the minor actinides (MAs) containing fuels; nuclear constants measurement and evaluation (selective cross-sections, fission fragments yields, delayed neutron parameters) especially for MA burners; demonstration of the feasibility of the safe and economic MA burner cores; knowledge of the impact of maximum tolerable amount of rare earths in americium containing fuels. Refs, figs and tabs

Slovakia: Proposal of movable reflector for fast reactor design

International Nuclear Information System (INIS)

Vrban, B.

2015-01-01

In fast reactors a larger migration area leading to a significant leak of neutrons can be observed because especially the transport cross-sections are in general smaller as compared to light water reactors. The utilization of a moveable reflector system in conjunction with dedicated safety control rods can increase the ability of accident managing due to enhanced escaping neutrons which otherwise would be reflected back into the fuel zone. The paper demonstrates the possibility of better controlling the transient reactor by additionally moving selected reflector subassemblies equipped with the neutron trap. The main purpose of the analysis of the Gas-cooled Fast Reactor (GFR) presented in the full paper is investigation of the kinetic parameters and of the control and reflector rod worth, as well as optimization of the parts used for partial reflector withdrawal. The results found in this study may serve for future design improvements of other designs such as the liquid metal cooled fast reactors

Total decay heat estimates in a proto-type fast reactor

International Nuclear Information System (INIS)

Sridharan, M.S.

2003-01-01

Full text: In this paper, total decay heat values generated in a proto-type fast reactor are estimated. These values are compared with those of certain fast reactors. Simple analytical fits are also obtained for these values which can serve as a handy and convenient tool in engineering design studies. These decay heat values taken as their ratio to the nominal operating power are, in general, applicable to any typical plutonium based fast reactor and are useful inputs to the design of decay-heat removal systems

Irradiation behavior of metallic fast reactor fuels

International Nuclear Information System (INIS)

Pahl, R.G.; Porter, D.L.; Crawford, D.C.; Walters, L.C.

1991-01-01

Metallic fuels were the first fuels chosen for liquid metal cooled fast reactors (LMR's). In the late 1960's world-wide interest turned toward ceramic LMR fuels before the full potential of metallic fuel was realized. However, during the 1970's the performance limitations of metallic fuel were resolved in order to achieve a high plant factor at the Argonne National Laboratory's Experimental Breeder Reactor II. The 1980's spawned renewed interest in metallic fuel when the Integral Fast Reactor (IFR) concept emerged at Argonne National Laboratory. A fuel performance demonstration program was put into place to obtain the data needed for the eventual licensing of metallic fuel. This paper will summarize the results of the irradiation program carried out since 1985

Technical committee meeting on Liquid Metal Fast Reactor (LMFR) developments. 33rd annual meeting of the International Working Group on Fast Reactors (IWG-FR). Working material

International Nuclear Information System (INIS)

2000-01-01

Over the past 33 years, the IAEA has actively encouraged and advocated international cooperation in fast reactor technology. The present publication contains information on the status of fast reactor development and on worldwide activities in this advanced nuclear power technology during 1999/2000, as reported at the 33. annual meeting of the International Working Group on Fast Reactors. It is intended to provide information regarding the current status of LMFR development in IAEA Member States

Discharges from a fast reactor reprocessing plant

International Nuclear Information System (INIS)

Barnes, D.S.

1987-01-01

The purpose of this paper is to assess the environmental impact of the calculated routine discharges from a fast reactor fuel reprocessing plant. These assessments have been carried out during the early stages of an evolving in-depth study which culminated in the design for a European demonstration reprocessing plant (EDRP). This plant would be capable of reprocessing irradiated fuel from a series of European fast reactors. Cost-benefit analysis has then been used to assess whether further reductions in the currently predicted routine discharges would be economically justified

Effect of Fast Neutron to MA/PU Burning/Transmutation Characteristic Using a Fast Reactor

International Nuclear Information System (INIS)

Marsodi; Lasman, As Natio; Kimamoto, A.; Marsongkohadi; Zaki, S.

2003-01-01

MA/Pu burning/transmutation has been studied and evaluated using fast neutrons. Generally, neutron density at this fast burner reactor and transmutation has spectrum energy level around 0.2 MeV with wide enough variation, i.e. from low neutron spectrum to its peak is 0.2 MeV. This neutron spectrum energy level depends on the kind of cooler material or fuel used. Neutron spectrum higher than fast power reactor neutron spectrum is found by means of changing oxide fuel by metallic fuel and changing natrium cooler material by metallic or gas cooler material. This evaluation is conducted by various variations in accordance with the kind of fuel or cooler, MA/Pu fractions and fuel comparison fraction with respect to its cooler in order to get better neutron usage and MA/Pu burning speed. Reactor calculation evaluation in this paper was conducted with 26-group nuclear data cross section energy spectrum. The main purpose of the discussion is to know the effect of fast neutrons to burning/transmutation MA/Pu using fast neutrons

Fast Reactor Programme. Second Quarter 1969. Progress Report. RCN Report

International Nuclear Information System (INIS)

Hoekstra, E.K.

1969-12-01

This progress report covers fast reactor research carried out by RCN during the second quarter 1969 forming part of the integrated fast breeder research and development programme also in progress at the national nuclear research centres Karlsruhe and Mol. The combined effort is based on a memorandum of co-operation in this field signed by the respective governments in 1968 and on a memorandum of understanding signed by the research centres. The RCN contribution is mainly concerned with the core of the fast breeder reactor and related safety aspects and, as such, must be looked upon as being complementary to the industrial research pro- field of fast reactors. The contribution comprises the following six items: - A Æéatîtôr , physics programme to determine the influence of fission products on several main characteristics of the reactor core such as void coefficient, Doppler coefficient and breeding ratio; - A fuel performance programme in which both stationary and transient irradiations are being carried out to establish the temperature and power limits of fuel rods; also the consequences of loss- of-cooling will be investigated; - Investigation into the change in mechanical properties of fuel canning materials due to high fast neutron doses; - A study of the corrosion behaviour of canning materials and their compatibility with the fuel under conditions of high temperature and high pressure; - Investigation into the behaviour of aerosols of fission products which could be formed after a fast reactor accident; a thorough understanding is of utmost importance for the reactor safety assessment ; - Studies on heat transfer in the reactor core. As fast breeders operate at high power densities, an accurate knowledge on the heat transfer phenomena is required

Materials requirements for liquid metal fast breeder reactors

International Nuclear Information System (INIS)

Bennett, J.W.; Horton, K.E.

1978-01-01

Materials requirements for Liquid Metal Fast Breeder Reactors (LMFBRs) are quite varied with requisite applications ranging from ex-reactor components such as piping, pumps, steam generators and heat exchangers to in-reactor components such as heavy section reactor vessels, core structurals, fuel pin cladding and subassembly flow ducts. Requirements for ex-reactor component materials include: good high temperature tensile, creep and fatigue properties; compatibility with high temperature flowing sodium; resistance to wear, stress corrosion cracking, and crack propagation; and good weldability. Requirements for in-reactor components include most of those cited above for ex-reactor components as supplemented by the following: resistance to radiation embrittlement, swelling and radiation enhanced creep; good neutronics; compatibility with fuel and fission product materials; and resistance to mass transfer via flowing sodium. Extensive programs are currently in place in a number of national laboratories and industrial contractors to address the materials requirements for LMFBRs. These programs are focused on meeting the near term requirements of early LMFBRs such as the Fast Flux Test Facility and the Clinch River Breeder Reactor as well as the longer term requirements of larger near-commercial and fully-commercial reactors

Fast reactor system factors affecting reprocessing plant design

International Nuclear Information System (INIS)

Allardice, R.H.; Pugh, O.

1982-01-01

The introduction of a commercial fast reactor electricity generating system is very dependent on the availability of an efficient nuclear fuel cycle. Selection of fuel element constructional materials, the fuel element design approach and the reactor operation have a significant influence on the technical feasibility and efficiency of the reprocessing and waste management plants. Therefore the fast reactor processing plant requires liaison between many design teams -reactor, fuel design, reprocessing and waste management -often with different disciplines and conflicting objectives if taken in isolation and an optimised approach to determining several key parameters. A number of these parameters are identified and the design approach discussed in the context of the reprocessing plant. Radiological safety and its impact on design is also briefly discussed. (author)

A Neutronic Feasibility Study on the Recycling of an Oxide Fuel in Sodium-Cooled Fast Reactors

Energy Technology Data Exchange (ETDEWEB)

Roh, Gyu Hong; Choi, Hang Bok

2006-06-15

Neutronic feasibility was implemented for the recycling of a mixed oxide fuel in sodium-cooled fast reactors (SFR) through a thermal/mechanical dry process, which is recognized as one of the most proliferation- resistant recycling processes. In order to assess the applicability of a simple dry process which is not capable of completely removing all the fission products from a spent fuel, sensitivity calculations were performed for the reactor physics parameters with a dependency on the fission product removal rate of the recycled spent fuel. The equilibrium core calculations were performed by the REBUS-3 code for a BN-600 core without blanket fuels and a modified core with an increased fuel volume fraction. The reactor performance parameters such as the transuranic content, breeding ratio, peak linear power, burnup reactivity swing and reactivity coefficients were calculated for an equilibrium core under a fixed fuel management scheme. The results showed that a recycling of the oxide fuel in the SFR is feasible if the fission products are removed by more than 70% through the dry process as far as the material balance is concerned. However the physics analysis also showed that some of the physics design parameters are slightly deteriorated. The results of this study indicate that the recycling characteristics can be improved if the dry process can remove more fission products, and the reactor configuration is further optimized or the spent fuel composition is adjusted.

A Neutronic Feasibility Study on the Recycling of an Oxide Fuel in Sodium-Cooled Fast Reactors

International Nuclear Information System (INIS)

Roh, Gyu Hong; Choi, Hang Bok

2006-06-01

Neutronic feasibility was implemented for the recycling of a mixed oxide fuel in sodium-cooled fast reactors (SFR) through a thermal/mechanical dry process, which is recognized as one of the most proliferation- resistant recycling processes. In order to assess the applicability of a simple dry process which is not capable of completely removing all the fission products from a spent fuel, sensitivity calculations were performed for the reactor physics parameters with a dependency on the fission product removal rate of the recycled spent fuel. The equilibrium core calculations were performed by the REBUS-3 code for a BN-600 core without blanket fuels and a modified core with an increased fuel volume fraction. The reactor performance parameters such as the transuranic content, breeding ratio, peak linear power, burnup reactivity swing and reactivity coefficients were calculated for an equilibrium core under a fixed fuel management scheme. The results showed that a recycling of the oxide fuel in the SFR is feasible if the fission products are removed by more than 70% through the dry process as far as the material balance is concerned. However the physics analysis also showed that some of the physics design parameters are slightly deteriorated. The results of this study indicate that the recycling characteristics can be improved if the dry process can remove more fission products, and the reactor configuration is further optimized or the spent fuel composition is adjusted

Containment atmosphere cooling system for experimental fast reactor 'JOYO'

International Nuclear Information System (INIS)

Sasaki, Mikio; Hoshi, Akio; Sato, Morihiko; Takeuchi, Kaoru

1979-01-01

The experimental fast reactor ''JOYO'', the first sodium-cooled fast reactor in Japan, achieved the initially licensed full power operation (50 MW) in July 1978 and is now under steady operation. Toshiba has participated in the construction of this reactor as a leading manufacturer and supplied various systems. This article outlines the design philosophy, system concepts and the operating experience of the containment atmosphere cooling system which has many design interfaces throughout the whole plant and requires especially high reliability. The successful performance of this system during the reactor full-power operation owes to the spot cooling design philosophy and to the preoperational adjustment of heat load during the preheating period of reactor cooling system peculiar to FBR. (author)

Fast-reactor-data testing of ENDF/B-V at ORNL

International Nuclear Information System (INIS)

Wright, R.Q.; Ford, W.E. III; Lucius, J.L.; Webster, C.C.; Marable, J.H.

1982-01-01

The Cross Section Evaluation Working Group (CSEWG) is coordinating a program to assess the adequacy of ENDF/B-V cross sections for both fast- and thermal-reactor design applications. A secondary goal is to evaluate cross-section processing codes, cross-section libraries, and radiation-transport codes. Fast reactor data testing (FRDT) goals are accomplished, in part, by comparison of calculated results with documented performance parameters of CSEWG fast reactor benchmarks and with results obtained by other data testers. The purpose of this paper is to describe the results of FRDT at Oak Ridge National Laboratory

Fast reactors: R and D targets and outlook for their introduction

International Nuclear Information System (INIS)

Poplavsky, V.; Barre, B.; Aizawa, K.

1997-01-01

In this paper the current status of fast reactors development is briefly outlined, including experimental, demonstration, and commercial installations. Data on the experience gained in development and operation of NPPs with reactors of this type are presented. The issues are discussed in connection with possibilities of fast reactor development in the nuclear power structure for the near (up to 2010-2020) and distant future. In the final part of the paper, an analysis is given of possible ways for R and D development in the field of NPPs with fast neutron reactors. (author)

Fast reactors will eat nuclear waste from LWR

Energy Technology Data Exchange (ETDEWEB)

Tokiwai, Moriyasu [Central Research Inst. of Electric Power Industry, Komae, Tokyo (Japan). Komae Res., Lab.

1999-12-01

Although nuclear power is one of the indispensable energy sources to support modern life styles in developed countries, it becomes harder and harder to increase its capacity. Newspaper reported that there are numbers of evidences showing the suppression effect on cancer by the low level of radiation. It is expected for public people that the fear for radiation induced harm on health will mitigate through the explanation based on scientific evidences. Safe management of radioactive waste is one of the most serious issues to be solved. The neutron at fast reactors can eat more effectively the long lived several nuclear waste materials from light water reactor system, The key issue is to develop the fast reactor fuel cycle system technologies that are more economical, more proliferation resistant and higher breeding ratio. The Metallic Fuel Cycle is one of the options for the future fast breeder reactor and its related fuel cycle that enable to give the answer for the radioactive waste issues. The attractiveness of the metallic fuel cycle concept is briefly described. (author)

A review of fast reactor programme in Japan

International Nuclear Information System (INIS)

1998-01-01

This report describes the development and activities on fast reactor in Japan for the period of April 1996 - March 1997. During this period, the 30th duty cycle operation has been started in the Experimental Fast Reactor ''''Joyo''''. The cause investigation on the sodium leak incident has completed and the safety examination are being performed in the Prototype Fast Breeder Reactor ''''Monju''''. The three years design study since FY1994 on the plant optimization of the Demonstration FBR has been completed by the Japan Atomic Power Company (JAPC). Related research and development works are underway at several organizations under the discussion and coordination of the Japanese FBR R and D Steering Committee, which is composed of Power Reactor and Nuclear Fuel Development Corporation (PNC), JAPC, Japan Atomic Energy Research Institute (JAERI) and Central Research Institute of Electric Power Industry (CRIEPI). In November 1996, the Japan Atomic Energy Commission (JAEC) established a Social Gathering Meeting to discuss generally the significance of FBR development in Japan for the future. (author)