The Regional Biomass-Energy Agency (ERBE): an opportunity for the biomass-energy development in Wallonia

International Nuclear Information System (INIS)

Lemaire, P.; Menu, J.F.; Belle, J.F. van; Schenkel, Y.

1997-01-01

In 1995, the European Commission (Directorate-General for Energy) and the Walloon government set up a biomass-energy agency (ERBE), to promote and build biomass-energy projects in Wallonia (Belgium). A survey of biomass-energy potential indicates that wood-energy seems to offer the best utilization opportunities. Forest and logging residues, sawmills' and joineries' off-cuts, pallets residues, etc. could be burnt in wood district heating units with a significant social benefit. Consequently, the ERBE Agency is trying to set up projects in this way in Austria (+/- 100 wood heating systems) or in Sweden. It serves to inform industries and municipalities about biomass-energy, to advise them in the building of biomass-energy projects, to identify their energy needs and their biomass resources, to carry out prefeasibility studies, to inform them about financing opportunities, and so on. (author)

Biomass - Activities and projects in 2004; Biomasse - Aktivitaeten und Projekte 2004

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D; Guggisberg, B

2005-07-01

This annual report by the Swiss Federal Office of Energy (SFOE) presents an overview of the Swiss research programme on biomass and its efficient use both as a source of heat and electrical power and as a fuel. Work done and results obtained in the year 2004 are looked at. Topics covered include combustion and gasification of wood, the fermentation of biogenic wastes and developments in the bio-fuels area. Several projects in each of these areas are discussed. National co-operation with various universities, private organisations and other federal offices is discussed, as are contributions made to symposia and exhibitions in the biomass area. International co-operation within the framework of International Energy Agency (IEA) tasks is mentioned. Various pilot and demonstration projects in the combustion, gasification and fermentation areas are listed and discussed.

Future challenges for woody biomass projections

NARCIS (Netherlands)

Schadauer, K.; Barreiro, Susana; Schelhaas, M.; McRoberts, Ronald E.

2017-01-01

Many drivers affect woody biomass projections including forest available for wood supply, market behavior, forest ownership, distributions by age and yield classes, forest typologies resulting from different edaphic, climatic conditions, and last but not least, how these factors are incorporated

Tax issues and incentives for biomass projects

International Nuclear Information System (INIS)

Martin, K.

1993-01-01

The federal government offers a number of tax incentives to developers of biomass projects. This paper describes each tax benefit, explains what conditions must be met before the benefit is available, and offers practical insights gained from working for over 10 years in the field. Understanding what tax benefits are available is important because the more tax benefits a developer can qualify for in connection with his project, the less expensive the project will be to build and operate and the easier it will be to arrange financing because there will be higher returns in the project for potential investors

Vegetation Composition, Biomass Production, Carrying Capacity ...

African Journals Online (AJOL)

Acacia tortilis, Acacia nilotica, Acacia mellifera and Acacia seyal were the most dominant shrubs with scattered Caddaba rotundifolia, Caddaba furmisa, Seddera bagshawei, Tamarix nilotica, Dobera glabra and abundant Parthenium hysterophorus, Cissus rotundifolia and C. quadrangularis. The grass biomass estimated in ...

Biomass Burning Observation Project (BBOP) Final Campaign Report

Energy Technology Data Exchange (ETDEWEB)

Kleinman, LI [Brookhaven National Lab. (BNL), Upton, NY (United States); Sedlacek, A. J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-01-01

The Biomass Burning Observation Project (BBOP) was conducted to obtain a better understanding of how aerosols generated from biomass fires affect the atmosphere and climate. It is estimated that 40% of carbonaceous aerosol produced originates from biomass burning—enough to affect regional and global climate. Several biomass-burning studies have focused on tropical climates; however, few campaigns have been conducted within the United States, where millions of acres are burned each year, trending to higher values and greater climate impacts because of droughts in the West. Using the Atmospheric Radiation Measurement (ARM) Aerial Facility (AAF), the BBOP deployed the Gulfstream-1 (G-1) aircraft over smoke plumes from active wildfire and agricultural burns to help identify the impact of these events and how impacts evolve with time. BBOP was one of very few studies that targeted the near-field time evolution of aerosols and aimed to obtain a process-level understanding of the large changes that occur within a few hours of atmospheric processing.

Biomass gasification to heat, electricity and biofuels. HighBio project publication

Energy Technology Data Exchange (ETDEWEB)

Lassi, U.; Wikman, B. (eds.)

2011-07-01

Renewable energy and the use of biomass in energy production promotes sustainable development and decreases the use of fossil fuels. Biomass, e.g. wood chips can be used in the production of heat and electricity, as well as being used as a biofuel component and novel product for the chemical industry. Efficient utilisation of biomass requires a high level of knowledge and the development of new processes to create a new way of thinking. In this process, international co-operation plays a significant role. The aim of the HighBio project was to produce new information on biomass gasification and the utilisation opportunities of product gas in biofuel and biochemicals production. The project was also aimed at studying utilisation properties of biogasification ashes in distributed energy production. Small-scaled CHP plants can be used for simultaneous heat and power production by gasifying wood chips and by burning energy intensive product gas. Compared with thermal combustion, particulate emissions from gasification are lower, which also contributes to the EU's ever tightening emission legislation. Several small and middle scale companies in the Northern part of Finland and Sweden have worked with biomass gasification, and during the project, the birth of new ones has been seen. In this development stage, researchers of the HighBio project have also been strongly involved. Increased use of renewable energy opens up new possibilities for entrepreneurship and the birth of new companies, especially in rural areas. In order to enable these opportunities, we need research data from the universities, novel innovations, and especially their successful commercialisation. The HighBio project has also contributed to tackling those challenges by arranging research seminars and meetings to companies and other interest groups, as well as by establishing research activities and collaborations. Regional collaboration combined with national and international research networks

Quebec Centre for Biomass Valorization, annual report 1990/91. Centre quebecois de valorisation de la biomasse, rapport annuel 1990/91

Energy Technology Data Exchange (ETDEWEB)

1991-06-01

The Quebec Centre for Biomass Valorization has the objectives of facilitating research pertaining to that subject while relating that research to industrial and community needs, channelling financial resources into biomass research, encouraging industry participation, and supplying information to prospective investigators for carrying out relevant projects. In 1990/91, this organization received an additional mandate from the provincial government to continue its activities. Of 253 projects proposed in 1991, 83 were related to forest biomass, 73 to agricultural biomass, 25 to aquatic biomass, 34 to peat, and 38 to urban wastes. The products to be derived from this biomass are in the alimentary, biological, chemical/material, energy, and decontamination categories. Total disbursements for the approved projects were about $14.6 million. A summary is provided of the previous 5 years of activity in such areas as wood polymers, fermentation, bioherbicides, peat-based substrates, biofiltration, and waste treatment. Objectives for the next five years are also outlined. Key sectors are identified as the valorization of lignocellulosic and agricultural wastes, municipal biomass, and peat materials. Financial statements are also included. 4 figs., 5 tabs.

Infrastructure improvement project for rationalization of international energy use. Basic survey project on efficient use of unutilized biomass in ASEAN countries

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Surveys and researches were performed on a small-size power generation system using biomass which is available affluently in ASEAN countries, but is not fully utilized. The current fiscal year has carried out researches on a small-size power generation system using palm shells available in great abundance in Malaysia. Having been performed in December 2000 are the preliminary conferences of ACE with Ptm, collection of necessary data and literatures, and decisions on the specifications of the small-size power generation system and its basic design conditions. In January 2001, collection of literatures related to production, combustion, and use of the biomass for the purpose of power generation and other than the power generation, as well as visits to palm oil factories were implemented. In March 2001, the final specifications were decided on the small-size power generation system. This project has carried out not only the discussions on the specifications of devices, but also joint researches on design ideas to facilitate technological transfer. This paper includes the reports and literatures used at the workshops in addition to the basic specifications of the small-size power generation system that can be used in wide areas. (NEDO)

Bottom-up comparisons of CO2 storage and costs in forestry and biomass energy projects

International Nuclear Information System (INIS)

Swisher, J.N.

1993-01-01

In order to include forestry and biomass energy projects in a possible CO 2 emission reduction regime, and to compare the costs of individual projects or national programs, it is necessary to determine the rate of equivalency between carbon in fossil fuel emissions and carbon stored in different types of forestry, biomass and renewable energy projects. This paper presents a comprehensive and consistent methodology to account for the costs and carbon flows of different categories of forestry and biomass energy projects and describes the application of the methodology to several sets of projects in Latin America. The results suggest that both biomass energy development and forestry measures including reforestation and forest protection can contribute significantly to the reduction of global CO 2 emissions, and that local land-use capacity must determine the type of project that is appropriate in specific cases. No single approach alone is sufficient as either a national or global strategy for sustainable land use or carbon emission reduction

Stakeholder preferences towards the sustainable development of CDM projects: Lessons from biomass (rice husk) CDM project in Thailand

International Nuclear Information System (INIS)

Parnphumeesup, Piya; Kerr, Sandy A.

2011-01-01

This research applies both quantitative and qualitative methods to investigate stakeholder preferences towards sustainable development (SD) priorities in Clean Development Mechanism (CDM) projects. The CDM's contribution to SD is explored in the context of a biomass (rice husk) case study conducted in Thailand. Quantitative analysis ranks increasing the usage of renewable energy as the highest priority, followed by employment and technology transfer. Air pollution (dust) is ranked as the most important problem. Preference weights expressed by experts and local resident are statistically different in the cases of: employment generation; emission reductions; dust; waste disposal; and noise. Qualitative results, suggest that rice husk CDM projects contribute significantly to SD in terms of employment generation, an increase in usage of renewable energy, and transfer of knowledge. However, rice husk biomass projects create a potential negative impact on air quality. In order to ensure the environmental sustainability of CDM projects, stakeholders suggest that Thailand should cancel an Environmental Impact Assessment (EIA) exemption for CDM projects with an installed capacity below 10 MW and apply it to all CDM projects. - Highlights: → Stakeholders rank increasing the usage of renewable energy as the highest priority. → Biomass (rice husk) CDM projects create a potential negative impact on air quality. → Rice husk CDM projects cannot give an extra income to farmers. → Preference weights expressed by experts and local residents are statistically different.

Transportation Energy Futures Series. Projected Biomass Utilization for Fuels and Power in a Mature Market

Energy Technology Data Exchange (ETDEWEB)

Ruth, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mai, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Newes, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Aden, A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Warner, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Uriarte, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Inman, D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simpkins, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Argo, A. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-03-01

The viability of biomass as transportation fuel depends upon the allocation of limited resources for fuel, power, and products. By focusing on mature markets, this report identifies how biomass is projected to be most economically used in the long term and the implications for greenhouse gas (GHG) emissions and petroleum use. In order to better understand competition for biomass between these markets and the potential for biofuel as a market-scale alternative to petroleum-based fuels, this report presents results of a micro-economic analysis conducted using the Biomass Allocation and Supply Equilibrium (BASE) modeling tool. The findings indicate that biofuels can outcompete biopower for feedstocks in mature markets if research and development targets are met. The BASE tool was developed for this project to analyze the impact of multiple biomass demand areas on mature energy markets. The model includes domestic supply curves for lignocellulosic biomass resources, corn for ethanol and butanol production, soybeans for biodiesel, and algae for diesel. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.

Transportation Energy Futures Series: Projected Biomass Utilization for Fuels and Power in a Mature Market

Energy Technology Data Exchange (ETDEWEB)

Ruth, M.; Mai, T.; Newes, E.; Aden, A.; Warner, E.; Uriarte, C.; Inman, D.; Simpkins, T.; Argo, A.

2013-03-01

The viability of biomass as transportation fuel depends upon the allocation of limited resources for fuel, power, and products. By focusing on mature markets, this report identifies how biomass is projected to be most economically used in the long term and the implications for greenhouse gas (GHG) emissions and petroleum use. In order to better understand competition for biomass between these markets and the potential for biofuel as a market-scale alternative to petroleum-based fuels, this report presents results of a micro-economic analysis conducted using the Biomass Allocation and Supply Equilibrium (BASE) modeling tool. The findings indicate that biofuels can outcompete biopower for feedstocks in mature markets if research and development targets are met. The BASE tool was developed for this project to analyze the impact of multiple biomass demand areas on mature energy markets. The model includes domestic supply curves for lignocellulosic biomass resources, corn for ethanol and butanol production, soybeans for biodiesel, and algae for diesel. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.

Coming on stream: Financing biomass and alternative-fuel projects in the 1990s

International Nuclear Information System (INIS)

Mumford, E.B. Jr.

1993-01-01

Biomass-energy and alternative-fuels projects make environmental sense, but do they make economic sense? In the current project-finance environment, moving ideas off the drawing board and transforming them into reality takes more than vision and commitment; it takes the ability to understand and address the financial markets' perception of risk. This paper examines the state of the project-finance market, both as it pertains to biomass and alternative-fuels projects and in more general terms, focusing on what project sponsors and developers need to dot to obtain both early-state and construction/term financing, and the role a financial adviser can play in helping ensure access to funds at all stages

Rwanda after the war: supply and rational management of biomass energy

International Nuclear Information System (INIS)

Hategeka, A.

1997-01-01

This chapter discusses the effects of the war in Rwanda on biomass energy and biomass energy supply. Seven projects identified to be carried out immediately involve rationalisation of biomass energy use in urban and rural areas, supplying charcoal from forest thinnings, rehabilitation of damaged forests, examination of the feasibility of peat extraction, urban supply of peat, wood energy conservation, and pilot production of papyrus briquettes. (UK)

Biomass for electricity

International Nuclear Information System (INIS)

Barbucci, P.; Neri, G.; Trebbi, G.

1995-01-01

This paper describes the activities carried out at ENEL-Thermal research center to develop technologies suitable to convert biomass into power with high conversion efficiency: a demonstration project, Energy Farm, to build an Integrated Gasification Combined Cycle (IGCC) plant fed by wood chips; a demonstration plant for converting wood chips into oil by thermal conversion (pyrolysis oil); combustion tests of different oils produced by thermal conversion. 3 figs., 1 tab

Sustainable model for financial viability of decentralized biomass gasifier based power projects

NARCIS (Netherlands)

Palit, D.; Malhotra, R.; Kumar, Atul

2011-01-01

This paper made a modest attempt for designing a sustainable model for financial viability of biomass gasifier power projects for enhancing electricity access in India and other developing countries. For long term sustainability of distributed generation projects in remote rural areas, viability

New bern biomass to energy project Phase I: Feasibility study

Energy Technology Data Exchange (ETDEWEB)

Parson, F.; Bain, R.

1995-10-01

Weyerhaeuser, together with Amoco and Carolina Power & Light, performed a detailed evaluation of biomass gasification and enzymatic processing of biomass to ethanol. This evaluation assesses the potential of these technologies for commercial application to determine which technology offers the best opportunity at this time to increase economic productivity of forest resources in an environmentally sustainable manner. The work performed included preparation of site-specific plant designs that integrate with the Weyerhaeuser New Bern, North Carolina pulp mill to meet overall plant energy requirements, cost estimates, resource and product market assessments, and technology evaluations. The Weyerhaeuser team was assisted by Stone & Webster Engineering Corporation and technology vendors in developing the necessary data, designs, and cost information used in this comparative study. Based on the information developed in this study and parallel evaluations performed by Weyerhaeuser and others, biomass gasification for use in power production appears to be technically and economically viable. Options exist at the New Bern mill which would allow commercial scale demonstration of the technology in a manner that would serve the practical energy requirements of the mill. A staged project development plan has been prepared for review. The plan would provide for a low-risk and cost demonstration of a biomass gasifier as an element of a boiler modification program and then allow for timely expansion of power production by the addition of a combined cycle cogeneration plant. Although ethanol technology is at an earlier stage of development, there appears to be a set of realizable site and market conditions which could provide for an economically attractive woody-biomass-based ethanol facility. The market price of ethanol and the cost of both feedstock and enzyme have a dramatic impact on the projected profitability of such a plant.

A Hybrid Life-Cycle Assessment of Nonrenewable Energy and Greenhouse-Gas Emissions of a Village-Level Biomass Gasification Project in China

Directory of Open Access Journals (Sweden)

Mingyue Pang

2012-07-01

Full Text Available Small-scale bio-energy projects have been launched in rural areas of China and are considered as alternatives to fossil-fuel energy. However, energetic and environmental evaluation of these projects has rarely been carried out, though it is necessary for their long-term development. A village-level biomass gasification project provides an example. A hybrid life-cycle assessment (LCA of its total nonrenewable energy (NE cost and associated greenhouse gas (GHG emissions is presented in this paper. The results show that the total energy cost for one joule of biomass gas output from the project is 2.93 J, of which 0.89 J is from nonrenewable energy, and the related GHG emission cost is 1.17 × 10⁻⁴ g CO₂-eq over its designed life cycle of 20 years. To provide equivalent effective calorific value for cooking work, the utilization of one joule of biomass gas will lead to more life cycle NE cost by 0.07 J and more GHG emissions by 8.92 × 10⁻⁵ g CO₂-eq compared to natural gas taking into consideration of the difference in combustion efficiency and calorific value. The small-scale bio-energy project has fallen into dilemma, i.e., struggling for survival, and for a more successful future development of village-level gasification projects, much effort is needed to tide over the plight of its development, such as high cost and low efficiency caused by decentralized construction, technical shortcomings and low utilization rate of by-products.

Economic sustainability of a biomass energy project located at a dairy in California, USA

International Nuclear Information System (INIS)

Camarillo, Mary Kay; Stringfellow, William T.; Jue, Michael B.; Hanlon, Jeremy S.

2012-01-01

Previous experience has demonstrated the tenuous nature of biomass energy projects located at livestock facilities in the U.S. In response, the economic sustainability of a 710 kW combined heat and power biomass energy system located on a dairy farm in California was evaluated. This biomass energy facility is unique in that a complete-mix anaerobic digester was used for treatment of manure collected in a flush-water system, co-digestates were used as additional digester feedstocks (whey, waste feed, and plant biomass), and the power plant is operating under strict regulatory requirements for stack gas emissions. Electricity was produced and sold wholesale, and cost savings resulted from the use of waste heat to offset propane demand. The impact of various operational factors was considered in the economic analysis, indicating that the system is economically viable as constructed but could benefit from introduction of additional substrates to increase methane and electricity production, additional utilization of waste heat, sale of digested solids, and possibly pursuing greenhouse gas credits. Use of technology for nitrogen oxide (NO x ) removal had a minimal effect on economic sustainability. - Highlights: ► We evaluated the economic sustainability of a dairy biomass energy project. ► The project is economically sustainable as currently operated. ► The simple payback period could be reduced if the system is operated near capacity. ► Co-digestion of off-site waste streams is recommended to improve profitability.

Digitization Projects Carried out by the Mathematical Institute Belgrade

OpenAIRE

Ognjanovič, Zoran; Mijajlovič, Žarco

2004-01-01

In this paper some current digitization projects carried out by the Mathematical Institute of Serbian Academy of Science and Arts Belgrade and the Faculty of Mathematics Belgrade are described. The projects concern developing of a virtual library of retro-digitized books and an Internet data base and presentation of electronic editions of some leading Serbian journals in science and arts, and the work on the South-Eastern European Digitization Initiative (SEEDI).

Solar-assisted biomass-district heating: projects in Austria and operational data; Solarunterstuetzte Biomasse-Fernwaermeversorgung: Projekte in Oesterreich und Betriebsdaten

Energy Technology Data Exchange (ETDEWEB)

Faninger, G. [Institut fuer Interdisziplinaere Forschung und Fortbildung der Universitaeten Klagenfurt, Innsbruck und Wien (IFF), Klagenfurt (Austria)

1998-12-31

In recent years small-volume biomass district heating systems (district heat grids) have attracted increasing interest in Austria. By the end of 1997 some 359 biomass-district heating systems with an overall capacity of approximately 483 MW were in operation. If a biomass-district heating plant and a solar plant are combined the solar plant can supply most of the heat required outside the heating season. At present Austria runs 12 solar-assisted biomass-district heating grids with collector areas between 225 square metres and 1,250 square metres. In order to run these biomass-district heating systems in an economically and technically efficient way it is necessary to assure high quality in terms of planning, construction and operation. A list of criteria is set up on the basis of first operational data in order to evaluate energy efficiency and economic performance. These criteria should be applied in order to ensure that energy, environment and economy are equally considered in the planning and construction of solar-assisted biomass-district heating plants. They should also be helpful for the approval procedures of projects. (orig.) [Deutsch] Kleinraeumige Biomasse-Fernwaermeanlagen (Nahwaermenetze) fanden in den letzten Jahren zunehmendes Interesse in Oesterreich. So waren Ende 1997 insgesamt 359 Biomasse-Fernwaermeanlagen mit einer installierten Gesamtleistung von etwa 483 MW in Betrieb. Die Kombination einer Biomasse-Fernwaermeanlage mit einer Solaranlage bringt den Vorteil, dass die Waermebereitstellung ausserhalb der Heizsaison zu einem hohen Anteil ueber die Solaranlage vorgenommen werden kann. Derzeit werden in Oesterreich 12 solarunterstuetzte Biomasse-Nahwaermenetze mit Kollektorflaechen von 225 m{sup 2} bis 1.250 m{sup 2} betrieben. Um einen moeglichst effizienten und damit auch wirtschaftlichen Betrieb von solarunterstuetzten Biomasse-Fernwaermeanlagen zu gewaehrleisten, werden hohe Anforderungen an Planung, Ausfuehrung und Betrieb gestellt. Auf der

Coal/Biomass-to-Liquids Demonstration Testing for DLA Energy: Report on Project Tests, Evaluations, and Recommendations

Science.gov (United States)

2015-08-20

Report January 2010-August 2015 Coal/ Biomass -to-Liquids Demonstration Testing for DLA Energy Report on Project Tests, Evaluations, and...produced commercially from coal and biomass mixtures while meeting the requirements of Section 526, which requires that GHG emissions from...gasification equipment, coals, and biomass used, and reports and analyzes the test results. Additionally, the team worked with DOE NETL to conduct

Adding gas from biomass to the gas grid

Energy Technology Data Exchange (ETDEWEB)

Hagen, Martin; Polman, Erik [GASTEC NV (Netherlands); Jensen, Jan K.; Myken, Asger [Danish Gas Technology Center A/S, Hoersholm (Denmark); Joensson, Owe; Dahl, Anders [Swedish Gas Center AB, Malmoe (Sweden)

2001-07-01

The aim of this project carried out in the framework of the Altener programme is to provide an overview of technologies for cleaning and upgrading of biogas for remote use. A further aim is to determine to what extent gases produced from biomass (digestion or gasification)can be added to the gas grid and what additional safety regulations are necessary. Finally, existing European standards and national legislation have been studied in order to determine the possibility of conflicting and/or missing regulations with the intended approach.The information collected in this project can be used to select promising technologies and may serve as background information for developing harmonised standards. This report describes the various production and cleaning techniques and the present requirements for the use of biogas. The technology for adding gas from biomass to the gas grid on a larger scale can contribute to a higher share of biomass in the energy supply and will also allow a highly efficient use of the energy contained in the biomass.Moderate tax incentives will make the use of gas from biomass economically attractive for large groups of end-users.

DUE GlobBiomass - Estimates of Biomass on a Global Scale

Science.gov (United States)

Eberle, J.; Schmullius, C.

2017-12-01

For the last three years, a new ESA Data User Element (DUE) project had focussed on creating improved knowledge about the Essential Climate Variable Biomass. The main purpose of the DUE GlobBiomass project is to better characterize and to reduce uncertainties of AGB estimates by developing an innovative synergistic mapping approach in five regional sites (Sweden, Poland, Mexico, Kalimantan, South Africa) for the epochs 2005, 2010 and 2015 and for one global map for the year 2010. The project team includes leading Earth Observation experts of Europe and is linked through Partnership Agreements with further national bodies from Brazil, Canada, China, Russia and South Africa. GlobBiomass has demonstrated how EO observation data can be integrated with in situ measurements and ecological understanding to provide improved biomass estimates that can be effectively exploited by users. The target users had mainly be drawn from the climate and carbon cycle modelling communities and included users concerned with carbon emissions and uptake due to biomass changes within initiatives such as REDD+. GlobBiomass provided a harmonised structure that can be exploited to address user needs for biomass information, but will be capable of being progressively refined as new data and methods become available. This presentation will give an overview of the technical prerequisites and final results of the GlobBiomass project.

Circumpolar arctic tundra biomass and productivity dynamics in response to projected climate change and herbivory.

Science.gov (United States)

Yu, Qin; Epstein, Howard; Engstrom, Ryan; Walker, Donald

2017-09-01

Satellite remote sensing data have indicated a general 'greening' trend in the arctic tundra biome. However, the observed changes based on remote sensing are the result of multiple environmental drivers, and the effects of individual controls such as warming, herbivory, and other disturbances on changes in vegetation biomass, community structure, and ecosystem function remain unclear. We apply ArcVeg, an arctic tundra vegetation dynamics model, to estimate potential changes in vegetation biomass and net primary production (NPP) at the plant community and functional type levels. ArcVeg is driven by soil nitrogen output from the Terrestrial Ecosystem Model, existing densities of Rangifer populations, and projected summer temperature changes by the NCAR CCSM4.0 general circulation model across the Arctic. We quantified the changes in aboveground biomass and NPP resulting from (i) observed herbivory only; (ii) projected climate change only; and (iii) coupled effects of projected climate change and herbivory. We evaluated model outputs of the absolute and relative differences in biomass and NPP by country, bioclimate subzone, and floristic province. Estimated potential biomass increases resulting from temperature increase only are approximately 5% greater than the biomass modeled due to coupled warming and herbivory. Such potential increases are greater in areas currently occupied by large or dense Rangifer herds such as the Nenets-occupied regions in Russia (27% greater vegetation increase without herbivores). In addition, herbivory modulates shifts in plant community structure caused by warming. Plant functional types such as shrubs and mosses were affected to a greater degree than other functional types by either warming or herbivory or coupled effects of the two. © 2017 John Wiley & Sons Ltd.

Biomass cogeneration: A business assessment

Science.gov (United States)

Skelton, J. C.

1981-11-01

The biomass cogeneration was reviewed. The business assessment is based in part on discussions with key officials from firms that have adopted biomass cogeneration systems and from organizations such as utilities, state and federal agencies, and banks directly involved in a biomass cogeneration project. The guide is organized into five chapters: biomass cogeneration systems, biomass cogeneration business considerations, biomass cogeneration economics, biomass cogeneration project planning, and case studies.

AgraPure Mississippi Biomass Project

Energy Technology Data Exchange (ETDEWEB)

Blackwell,D.A; Broadhead, L.W.; Harrell, W.J.

2006-03-31

The AgraPure Mississippi Biomass project was a congressionally directed project, initiated to study the utilization of Mississippi agricultural byproducts and waste products in the production of bio-energy and to determine the feasibility of commercialization of these agricultural byproducts and waste products as feedstocks in the production of energy. The final products from this project were two business plans; one for a Thermal plant, and one for a Biodiesel/Ethanol plant. Agricultural waste fired steam and electrical generating plants and biodiesel plants were deemed the best prospects for developing commercially viable industries. Additionally, oil extraction methods were studied, both traditional and two novel techniques, and incorporated into the development plans. Mississippi produced crop and animal waste biomasses were analyzed for use as raw materials for both industries. The relevant factors, availability, costs, transportation, storage, location, and energetic value criteria were considered. Since feedstock accounts for more than 70 percent of the total cost of producing biodiesel, any local advantages are considered extremely important in developing this particular industry. The same factors must be evaluated in assessing the prospects of commercial operation of a steam and electrical generation plant. Additionally, the access to the markets for electricity is more limited, regulated and tightly controlled than the liquid fuel markets. Domestically produced biofuels, both biodiesel and ethanol, are gaining more attention and popularity with the consuming public as prices rise and supplies of foreign crude become less secure. Biodiesel requires no major modifications to existing diesel engines or supply chain and offers significant environmental benefits. Currently the biodiesel industry requires Federal and State incentives to allow the industry to develop and become self-sustaining. Mississippi has available the necessary feedstocks and is

Commercialization of biomass energy projects: Outline for maximizing use of valuable tax credits and incentives

International Nuclear Information System (INIS)

Sanderson, G.A.

1994-01-01

The Federal Government offers a number of incentives designed specifically to promote biomass energy. These incentives include various tax credits, deductions and exemptions, as well as direct subsidy payments and grants. Additionally, equipment manufacturers and project developers may find several other tax provisions useful, including tax incentives for exporting U.S. good and engineering services, as well as incentives for the development of new technologies. This paper outlines the available incentives, and also addresses ways to coordinate the use of tax breaks with government grants and tax-free bond financing in order to maximize benefits for biomass energy projects

Switchgrass biomass energy storage project. Final report, September 23, 1996--December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Miller, G.A.; Teel, A.; Brown, S.S. [Iowa State Univ., Ames, IA (United States)

1996-07-01

The Chariton Valley Biomass Power Project, sponsored by the Chariton Valley RC&D Inc., a USDA-sponsored rural development organization, the Iowa Department of Natural Resources Energy Bureau (IDNR-EB), and IES Utilities, a major Iowa energy company, is directed at the development of markets for energy crops in southern Iowa. This effort is part of a statewide coalition of public and private interests cooperating to merge Iowa`s agricultural potential and its long-term energy requirements to develop locally sustainable sources of biomass fuel. The four-county Chariton Valley RC&D area (Lucas, Wayne, Appanoose and Monroe counties) is the site of one of eleven NREL/EPRI feasibility studies directed at the potential of biomass power. The focus of renewable energy development in the region has centered around the use of swithgrass (Panicum virgatum, L.). This native Iowa grass is one of the most promising sustainable biomass fuel crops. According to investigations by the U.S. Department of Energy (DOE), switchgrass has the most potential of all the perennial grasses and legumes evaluated for biomass production.

Biomass gasification as project for the rural development; A gaseificacao da biomassa como projeto para o desenvolvimento rural

Energy Technology Data Exchange (ETDEWEB)

Fernandes, Marcelo Cortes; Sanchez, Caio Glauco; Angulo, Mario Barriga; Parodi, Fernando Aurelio [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica]. E-mails: mcortes@fem.unicamp.br; caio@fem.unicamp.br; mariobarriga@hotmail.com; jambock@rocketmail.com

2002-07-01

This paper presents a study on the gasification of the biomass as a project for the rural development. Consider the biomass gasification as an sustainable alternative for energy generation, with low pollutant emission.

Biomass furnace: projection and construction

Energy Technology Data Exchange (ETDEWEB)

Melo, Fernanda Augusta de Oliveira; Silva, Juarez Sousa e; Silva, Denise de Freitas; Sampaio, Cristiane Pires; Nascimento Junior, Jose Henrique do [Universidade Federal de Vicosa (DEA/UFV), MG (Brazil). Dept. de Engenharia Agricola

2008-07-01

Of all the ways to convert biomass into thermal energy, direct combustion is the oldest. The thermal-chemical technologies of biomass conversion such as pyrolysis and gasification, are currently not the most important alternatives; combustion is responsible for 97% of the bio-energy produced in the world (Demirbas, 2003). For this work, a small furnace was designed and constructed to use biomass as its main source of fuel, and the combustion chamber was coupled with a helical transporter which linked to the secondary fuel reservoir to continually feed the combustion chamber with fine particles of agro-industrial residues. The design of the stove proved to be technically viable beginning with the balance of mass and energy for the air heating system. The proposed heat generator was easily constructed as it made use of simple and easily acquired materials, demanding no specialized labor. (author)

Biomass thermochemical conversion. Overview of results; Biomassan jalostus. Tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K [VTT Energy, Jyvaeskylae (Finland)

1997-12-01

The BIOENERGY Programme comprised two research institute projects, one enterprise project and two demonstration projects in 1996. The studies focused on the development of flash pyrolysis technology for biomass, and on the study of the storage stability of imported wood oils and of their suitability for use in oil-fired boilers and diesel power plants. Development of biomass gasification/gas engine concepts suitable for diesel power plants was also initiated. In addition to techno-economic assessments, experimental work was carried out focusing on the cleaning of gasification gas for engine use. Conversion of by-products from the pulping industry, in particular crude soap, into liquid fuels was studied by laboratory tests. Results obtained within IEA Bioenergy Agreement are also surveyed and a new three-year work plan is presented in the overview. (orig.)

The greenGain project - Biomass from landscape conservation and maintenance work for renewable energy production in the EU

Science.gov (United States)

Clalüna, Aline; Baumgarten, Wibke; García Galindo, Daniel; Lenz, Klaus; Doležal, Jan; De Filippi, Federico; Lorenzo, Joaquín; Montagnoli, Louis

2017-04-01

The project greenGain is looking for solutions to increase the energy production with regional and local biomass from landscape conservation and maintenance work, which is performed in the public interest. The relevant resources analysed in the greenGain model regions are, among others, biomass residues from clearing invasive vegetation in marginal agricultural lands in Spain, and residues from abandoned vineyards and olive groves in landscape protected areas in Italy. The main target groups are regional and local players who are responsible for maintenance and conservation work and for the biomass residue management in their regions. Moreover, the focus will be on service providers - including farmers and forest owners, their associations, NGOs, energy providers and consumers. Local companies, municipalities and public authorities are collaborating to identify the still underutilised non-food biomass resources and to discuss the way to integrate them into the local and regional biomass markets. Since the start of the three year project in January 2015, the partners from Italy, Spain, Czech Republic and Germany analysed, among other, the biomass feedstock potential coming from landscape maintenance work, and assessed various technological options to utilise this type of biomass. Further, political, legal and environmental aspects as well as awareness raising and public acceptance actions regarding the energetic use of biomass from public areas were assessed. greenGain also facilitates the exchange between model regions and other similar relevant players in the EU and shares examples of good practice. General guidelines will be prepared to guarantee a wide dissemination to other regions in the EU. Thus, the project shows how to build-up reliable knowledge on local availability of this feedstock and provides know-how concerning planning, harvesting, pre-treatment, storage and sustainable conversion pathways to a wide range of stakeholders in the EU.

Pilot project concerning the establishment of a collective biomass conversion plant on the island of Mors

International Nuclear Information System (INIS)

1993-06-01

This pilot project comprises a feasibility study in connection with plans to establish a biomass conversion plant, on the Danish island of Mors, which would provide methane to be used as fuel, in combination with natural gas, for a cogeneration plant serving six villages. The subjects of location, organization, the transportation of biomass, the design of the biomass conversion plant, economical aspects and conditions of the use of the methane are discussed as a basis for decisions in this respect. Environmental considerations are also dealt with. (AB)

Forest biomass-based energy

Science.gov (United States)

Janaki R. R. Alavalapati; Pankaj Lal; Andres Susaeta; Robert C. Abt; David N. Wear

2013-01-01

Key FindingsHarvesting woody biomass for use as bioenergy is projected to range from 170 million to 336 million green tons by 2050, an increase of 54 to 113 percent over current levels.Consumption projections for forest biomass-based energy, which are based on Energy Information Administration projections, have a high level of...

Biomass energy projects for joint implementation of the UN FCCC [Framework Convention on Climate Change

International Nuclear Information System (INIS)

Swisher, Joel N.; Renner, Frederick P.

1998-01-01

The UN Framework Convention on Climate Change (FCCC) allows for the joint implementation (JI) of measures to mitigate the emissions of greenhouse gases. The concept of JI refers to the implementation of such measures in one country with partial or full financial and/or technical support from another country, potentially fulfilling some of the supporting country's emission-reduction commitment under the FCCC. This paper addresses some key issues related to JI under the FCCC as they relate to the development of biomass energy projects for carbon offsets in developing countries. Issues include the reference case or baseline, carbon accounting and net carbon storage, potential project implementation barriers and risks, monitoring and verification, local agreements and host-country approval. All of these issues are important in project design and evaluation. We discuss briefly several case studies, which consist of a biomass-fueled co-generation projects under development at large sugar mills in the Philippines, India and Brazil, as potential JI projects. The case studies illustrate the benefits of bioenergy for reducing carbon emissions and some of the important barriers and difficulties in developing and crediting such projects. Results to date illustrate both the achievements and the difficulties of this type of project. (author)

Ethanol from lignocellulosic biomasses

International Nuclear Information System (INIS)

Ricci, E.; Viola, E.; Zimbardi, F.; Braccio, G.; Cuna, D.

2001-01-01

In this report are presented results achieved on the process optimisation of bioethanol production from wheat straw, carried out within the ENEA's project of biomass exploitation for renewable energy. The process consists of three main steps: 1) biomass pretreatment by means of steam explosion; 2) enzymatic hydrolysis of the cellulose fraction; 3) fermentation of glucose. To perform the hydrolysis step, two commercial enzymatic mixtures have been employed, mainly composed by β-glucosidase (cellobiase), endo-glucanase and exo-glucanase. The ethanologenic yeast Saccharomyces cerevisiae has been used to ferment the glucose in he hydrolyzates. Hydrolysis yield of 97% has been obtained with steam exploded wheat straw treated at 220 0 C for 3 minutes and an enzyme to substrate ratio of 4%. It has been pointed out the necessity of washing with water the pretreated what straw, in order to remove the biomass degradation products, which have shown an inhibition effect on the yeast. At the best process conditions, a fermentation yield of 95% has been achieved. In the Simultaneous Saccharification and Fermentation process, a global conversion of 92% has been obtained, which corresponds to the production of about 170 grams of ethanol per kilogram of exploded straw [it

Community outreach and education: key components of the Salix consortium's willow biomass project

International Nuclear Information System (INIS)

Volk, T.A.; Edick, S.; Brown, S.; Downing, M.

1999-01-01

This project facilitates the commercialization of willow biomass crops as a locally grown source of renewable energy. The challenge is to simultaneously optimize production and utilization technology, develop farmer interest and crop acreage, and establish stable and reliable markets. The participation of farmers and landowners, businesses, and local and regional governments in the process is essential for success. A three-phased approach elicits this participation: focused outreach and education, active involvement of potential producers of willow biomass crops, and the development of a user-friendly economic and business model that can be used by a variety of stakeholders. Barriers to commercialization have been identified, such as misconceptions about the production system and crop, assurances of a stable and reliable market for the material, and indications that the equipment and infrastructure to grow and process willow biomass crops are in place. Outreach efforts have specifically addressed these issues. As a result target audiences' responses have changed from passive observation to inquiries and suggestions for active participation. This shift represents a significant step towards the goal of making willow biomass crops a viable source of locally produced fuel. (author)

Integrated biomass utilization system developments (Kyoto-Bio-Cycle Project) and the effects of greenhouse gas reduction

International Nuclear Information System (INIS)

Nakamura, Kazuo; Hori, Hiroaki; Deguchi, Shinguo; Yano, Junya; Sakai, Shinichi

2010-01-01

Full text: The biomass available in Kyoto City located in urban area of Japan was estimated to be 2.02x10 6 t-wet/ yr (0.14x10 6 k liter/ yr oil equivalent), of which waste paper, waste timber, waste food, unused forest wood from the surrounding mountains and sewage sludge account for the largest amounts on an energy basis. These types of biomass can contribute to utilize for the reduction of fossil fuel consumption and for the reduction of greenhouse gas (GHG) emission. Therefore we started the Kyoto-Bio-Cycle Project (FY 2007-2009), which is the demonstration of renewable energy conversion technologies from the biomass. Specifically, we aimed for the greening of necessary materials such as methanol and the cyclic use of byproducts, with the bio diesel fuel production from used cooking oil (5 k liter-methyl ester/ day) as the core activity. Two technologies are being developed as part of the project. One is gasification and methanol synthesis to synthesize methanol with the pyrolytic gas generated from woody biomass. The other is high efficiency bio gasification that treats waste food, waste paper, and waste glycerin. This technology can improve the production rate of biogas and reduce the residue through the introduction of 80 degree Celsius-hyper-thermophilic hydrolysis in the 55 degree Celsius-thermophilic anaerobic fermentation process. These systems can produce 4 types of renewable energy such as bio diesel fuel, biogas, electricity and heat. And we conducted the life-cycle system analysis of GHG reduction effect for the demonstrating technologies, additionally we examined an optimum method of biomass utilization in the future low-carbon-society. As a result, the method that produces the liquid fuel (methanol, Ft oil) from dry biomass (waste timber, etc.) and the biogas from wet biomass (waste food, etc.) can reduce GHG emission highly at present and in the future, compared with the current direct combustion of biomass for the power generation. (author)

Implementation of the biomass gasification project for community empowerment at Melani village, Eastern Cape, South Africa

Energy Technology Data Exchange (ETDEWEB)

Mamphweli, Ntshengedzeni S.; Meyer, Edson L. [University of Fort Hare, Institute of Technology, Private Bag X1314, Alice 5700 (South Africa)

2009-12-15

Eskom and the University of Fort Hare are engaged in a biomass gasification project using the System Johansson Biomass gasifier (SJBG). The SJBG installed at Melani village in the Eastern Cape province of South Africa is used to assess the viability and affordability of biomass gasification in South Africa. A community needs assessment study was undertaken at the village before the installation of the plant. The study revealed the need for low-cost electricity for small businesses including growing of crops, chicken broilers, manufacturing of windows and door frames, sewing of clothing, bakery etc. It was also found that the community had a problem with the socio-environmental aspects of burning biomass waste from the sawmill furnace as a means of waste management. The SJBG uses the excess biomass materials (waste) to generate low-cost electricity to drive community economic development initiatives. A study on the properties and suitability of the biomass materials resulting from sawmill operation and their suitability for gasification using the SJBG was undertaken. The study established that the biomass materials meet the requirements for the SJBG. A 300 Nm{sup 3}/h SJBG was then manufactured and installed at the village. (author)

Advanced system demonstration for utilization of biomass as an energy source. Volume I. Scope and design criteria and project summary

Energy Technology Data Exchange (ETDEWEB)

None

1980-10-01

The information in this document is the result of an intensive engineering effort to demonstrate the feasibility of biomass-fueled boilers in cogeneration applications. This design package is based upon a specific site in the State of Maine. However, the design is generic in nature and could serve as a model for other biomass conversion facilities located anywhere biomass is abundant. The project's purpose and summary information are presented: the plant, its concept of operation; and other overall information are described. The capital cost estimate for the plant, and the basis upon which it was obtained are given; a schedule of key milestones and activities required to construct the plant and put it into operation is presented; and the general findings in areas that affect the viability of the project are discussed. The technical design, biomass study, environmental impact, commercialization, and economic factors are addressed. Each major plant area and the equipment and facilities that each includes are discussed in depth. Some overall plant requirements, including noise control, reliability, maintainability, and safety, are detailed. The results of each study relating to alternatives considered for optimizing plant operation parameters and specific system process schemes are briefly presented. All economic factors that affect the feasibility and viability of the biomass project are defined and evaluated.

Evaluating a biomass resource: The TVA region-wide biomass resource assessment model

Energy Technology Data Exchange (ETDEWEB)

Downing, M.; Graham, R.L. [Oak Ridge National Lab., TN (United States)

1993-12-31

The economic and supply structures of short rotation woody crop (SRWC) markets have not been established. Establishing the likely price and supply of SRWC biomass in a region is a complex task because biomass is not an established commodity as are oil, natural gas and coal. In this study we project the cost and supply of short-rotation woody biomass for the TVA region -- a 276 county area that includes all of Tennessee and portions of 10 contiguous states in the southeastern United States. Projected prices and quantities of SRWC are assumed to be a function of the amount and quality of crop and pasture land available in a region, expected SRWC yields and production costs on differing soils and land types, and the profit that could be obtained from current conventional crop production on these same lands. Results include the supply curve of SRWC biomass that is projected to be available from the entire region, the amount and location of crop and pasture land that would be used, and the conventional agricultural crops that would be displaced as a function of SRWC production. Finally, we show the results of sensitivity analysis on the projected cost and supply of SRWC biomass. In particular, we examine the separate impacts of varying SRWC production yields.

Biomass Gasification Research and Development Project

Energy Technology Data Exchange (ETDEWEB)

Ahring, Birgitte K. [Washington State Univ., Pullman, WA (United States)

2014-07-22

The overall objective of the BioChemCat project was to demonstrate the feasibility of using Advanced Wet Oxidation Steam-Explosion (AWEx) process to open and solubilize lignocellulosic biomass (LBM) coupled to an innovative mixed culture fermentation technology capable of producing a wide range of volatile fatty acids (VFAs) from all sugars present in LBM. The VFAs will then be separated and converted to hydrocarbon biofuel through catalytic upgrading. By continuously removing VFAs as they are produced (extractive fermentation), we were able to recover the VFAs while both eliminating the need for pH adjustment and increasing the fermentation productivity. The recovered VFAs were then esterified and upgraded to hydrocarbon fuels through a parallel series of hydrogenolysis/decarboxylation and dehydration reactions. We also demonstrated that a portion of the residual lignin fraction was solubilized and converted into VFAs, also improving the yields of VFAs. The remaining lignin fraction was then shown to be available (after dewatering and drying) for use as a lignin-enriched fuel pellet or as a feedstock for further processing.

Evaluating a biomass resource: The TVA region-wide biomass resource assessment model

International Nuclear Information System (INIS)

Downing, M.; Graham, R.L.

1993-01-01

Wood is an alterative fuel for electric power generation at coal-fired plants in the Tennessee Valley Authority (TVA) region. Short rotation wood energy crops (SRWC) could provide a source of this woody biomass. However, the economic and supply structures of SRWC markets have not been established. Establishing the likely price and supply of SRWC biomass in a region is a complex task because biomass is not an established commodity as are oil, natural gas and coal. In this study we project the cost and supply of short-rotation woody biomass for the TVA region -- a 276 county area that includes all of Tennessee and portions of 10 contiguous states in the southeastern United States. Projected prices and quantities of SRWC are assumed to be a function of the amount and quality of crop and pasture land available in a region. expected SRWC yields and production costs on differing soils and land types, and the profit that could be obtained from current conventional crop production on these same lands. Results include the supply curve of SRWC biomass that is projected to be available from the entire region, the amount and location of crop and pasture land that would be used, and the conventional agricultural crops that would be displaced as a function of SRWC production. Finally, we show the results of sensitivity analysis on the projected cost and supply of SRWC biomass. In particular, we examine the separate impacts of varying SRWC production yields

Torrefied biomass for use in power station sector; Torrefizierte Biomasse zum Einsatz im Kraftwerkssektor

Energy Technology Data Exchange (ETDEWEB)

Witt, Janet; Schaubach, Kay [Deutsches Biomasseforschungszentrum (DBFZ) gemeinnuetzige GmbH, Leipzig (Germany). Bereich Bioenergiesysteme; Kiel, Jaap; Carbo, Michiel [Energy Research Centre of the Netherlands (ECN), Petten (Netherlands); Wojcik, Magdalena [OFI Austrian Research Institute for Chemistry and Technology, Vienna (Austria)

2013-10-01

In the torrefaction process biomass is heated up in the absence of oxygen to a temperature of at least 250 C. By combining torrefaction with pelletisation or briquetting, biomass materials can be converted into a high-energy-density bioenergy carrier with improved behaviour in (long-distance) transport, handling and storage. Torrefaction also creates superior properties for biomass in many major end-use applications. The process has the potential to provide a significant contribution to an enlarged raw material portfolio for sustainable biomass fuel production inside Europe by including both agricultural and forestry biomass (residues). The article will briefly introduce the concept and objectives of the project and the different torrefaction technologies involved and then focus on the results obtained within the first project phase of the EU-project SECTOR. This comprises production of torrefied biomass batches, subsequent densification (pelletisation and briquetting), characterisation and Round Robin testing of characterisation methods, initial logistics and end-use performance testing, material safety data sheet preparation and sustainability assessment along the value chain. (orig.)

Bioenergy guide. Projecting, operation and economic efficiency of biomass power plants; Leitfaden Bioenergie. Planung, Betrieb und Wirtschaftlichkeit von Bioenergieanlagen

Energy Technology Data Exchange (ETDEWEB)

Deimling, S. [Stuttgart Univ. (DE). Inst. fuer Energiewirtschaft und Rationelle Energieanwendung (IER); Kaltschmitt, M; Schneider, B. [and others

2000-07-01

This guide gives an survey over planning, operation and economics of biomass conversion plants. Main topics are: production and supply of biomass fuels, combustion properties, licensing, cost and financing. It shows planning and management of projects and the legal background for Germany and the European Union.

Summaries of studies carried out in the NKS/BOK-2 project. Technical report

International Nuclear Information System (INIS)

Palsson, S.E.

2002-12-01

Summaries of studies carried out in the NKSBOK-2 project, Radiological and Environmental Consequences. The structure of the project as such is described in NKS-64, Radiological and Environmental Consequences - Final Report of the Nordic Nuclear Safety Research Project BOK-2. That report also includes compilations based on the summaries presented in this report. The project was carried out 1998-2001 with participants from all the Nordic countries. Representatives from the Baltic States were also invited to some of the meetings and seminars. The project consisted of work on terrestrial and marine radioecology and had a broad scope in order to enable participation of research groups with various fields of interest. The topics included improving assessment of old and recent fallout, use of radionuclides as tracers in Nordic marine areas, improving assessment of internal doses and use of mass spectrometry in radioecology. This report is a compilation of summaries from each research group, 32 papers in all, and gives references to papers published in scientific journals. Some of the studies have been described previously, at least to some degree, in NKS-70, Proceedings of the 8 th Nordic Seminar on Radioecology, 25-28 February 2001, Rovaniemi, Finland. (au)

Gasification of peat and biomass in suspension flow 2; Turpeen ja biomassan suspensiokaasutus 2

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E.; Hepola, J. [VTT Energy, Espoo (Finland); Haukka, P.; Raiko, R. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Thermal Engineering

1995-11-01

This project is an extension of the earlier Liekki-project 402, which was carried out in 1993-1994 in the Department of Thermal Engineering of Tampere University of Technology (TUT). In the previous project the feasibility of a two-stage entrained-flow gasification was studied by the means of process modeling and pyrolysis experiments. The present project carried out in cooperation with the Gasification Research Group of VTT and TUT. The aims of the project are: (a) to study the formation of blematic tar/soot compounds and nitrogen compounds in the conditions entrained flow gasification of biomass and peat, (b) to study the product yields and kinetics of pyrolysis and (c) to develop simulation methods for entrained flow pyrolysis and gasification. (author)

CFD-supported development of small-scale biomass furnaces; CFD-gestuetzte Entwicklung von Biomassefeuerungen im kleinen Leistungsbereich

Energy Technology Data Exchange (ETDEWEB)

Scharler, R. [Bios Bioenergiesystem GmbH, Graz (Austria); Obernberger, I. [Technische Univ. Eindhoven (Netherlands). Thermochemische Biomassekonversion; Weissinger, A. [Oesterreichische Kraft und Waerme aus Biomasse GmbH (KWB), St. Margarethen/Raab (Austria). Bereich Forschung und Entwicklung; Schmidt, W. [Oesterreichische Kraft und Waerme aus Biomasse GmbH (KWB), St. Margarethen/Raab (Austria). Bereich Produktentwicklung, Umwelt- und Informationsmanagement

2005-07-01

Despite the complexity of solid biomass combustion, the Bios Bioenergiesysteme GmbH, Graz, Austria, has successfully developed and optimised several biomass furnaces in the range of 500 kW to 30 MW based on CFD (Computational Fluid Dynamics). A project carried out in co-operation with the KWB Kraft und Waerme aus Biomasse GmbH, St. Margarethen, Austria, demonstrates the application of CFD for the efficient and improved design of small-scale furnaces for solid biofuels like pellets and wood chips as basis for a series production. (orig.)

Availability of biomass for energy production. GRAIN: Global Restrictions on biomass Availability for Import to the Netherlands

International Nuclear Information System (INIS)

Lysen, E.H.

2000-08-01

The report includes reports of activities that were carried out within the GRAIN project. This evaluation shows that the (technical) potential contribution of bio-energy to the future world's energy supply could be very large. In theory, energy farming on current agricultural land could contribute over 800 EJ, without jeopardising the world's food supply. Use of degraded lands may add another 150 EJ, although this contribution will largely come from crops with a low productivity. The growing demand for bio-materials may require a biomass input equivalent to 20-50 EJ, which must be grown on plantations when existing forests are not able to supply this growing demand. Organic wastes and residues could possibly supply another 40-170 EJ, with uncertain contributions from forest residues and potentially a very significant role for organic waste, especially when bio-materials are used on a larger scale. In total, the upper limit of the bio-energy potential could be over 1000 EJ per year. This is considerably more than the current global energy use of 400 EJ. However, this contribution is by no means guaranteed: crucial factors determining biomass availability for energy are: (1) Population growth and economic development; (2) The efficiency and productivity of food production systems that must be adopted worldwide and the rate of their deployment in particular in developing countries; (3) Feasibility of the use of marginal/degraded lands; (4) Productivity of forests and sustainable harvest levels; (5) The (increased) utilisation of bio-materials. Major transitions are required to exploit this bio-energy potential. It is uncertain to what extent such transitions are feasible. Depending on the factors mentioned above, the bio-energy potential could be very low as well. At regional/local level the possibilities and potential consequences of biomass production and use can vary strongly, but the insights in possible consequences are fairly limited up to now. Bio-energy offers

Biomass as a modern fuel

International Nuclear Information System (INIS)

Hall, D.O.; House, J.

1994-01-01

Case studies are presented for several developed and developing countries. Constraints involved in modernising biomass energy and the potential for turning them into entrepreneurial opportunities are discussed. It is concluded that the long term impacts of biomass programmes and projects depend mainly on ensuring sustainability, flexibility and replicability while taking account of local conditions and providing multiple benefits. Implementation of biomass projects requires governmental policy initiatives that will internalise the external economic, social and environmental costs of conventional fuel sources so that biomass fuels can become competitive on a ''level playing field''. Policies are also required to encourage R and D and commercialisation of biomass energy programs in close co-ordination with the private sector. (author)

Life cycle assessment of fossil and biomass power generation chains. An analysis carried out for ALSTOM Power Services

Energy Technology Data Exchange (ETDEWEB)

Bauer, Ch.

2008-12-15

This final report issued by the Technology Assessment Department of the Paul Scherrer Institute (PSI) reports on the results of an analysis carried out on behalf of the Alstom Power Services company. Fossil and biomass chains as well as co-combustion power plants are assessed. The general objective of this analysis is an evaluation of specific as well as overall environmental burdens resulting from these different options for electricity production. The results obtained for fuel chains including hard coal, lignite, wood, natural gas and synthetic natural gas are discussed. An overall comparison is made and the conclusions drawn from the results of the analysis are presented.

Development Strategies for Deployment of Biomass Resources in the Production of Biomass Power: November 6, 2001--February 28, 2003

Energy Technology Data Exchange (ETDEWEB)

Kaminsky, J.

2004-01-01

The study analyzes strategies for deployment of biomass resources for biopower generation. It compares biomass supply databases and the projected biopower market penetration for several alternative incentive scenarios. It analyzes the availability of biomass to meet the projected market demands and recommends future research.

Gasification of peat and biomass in suspension flow 2; Turpeen ja biomassan suspensiokaasutus 2

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E.; Hepola, J. [VTT Energy, Espoo (Finland); Haukka, P.; Vehmaan-Kreula, M.; Raiko, R. [Tampere Univ. of Technology (Finland)

1996-12-01

This project was an extension of the earlier Liekki-project 402 carried out in 1993-1994. The aims of the 1995 project were: (1) to study the formation of problematic tar/soot compounds and nitrogen pounds in the conditions of entrained flow gasification of biomass and peat, (2) study the product yields and kinetics of pyrolysis, and (3) to develop simulation methods for entrained flow pyrolysis and gasification. Pyrolysis and gasification tests were carried out at a new entrained flow reactor of the Gasification Research Group of VTT using mainly peat as the feedstock. The pyrolysis kinetics was studies using three particle size distributions of fuel peat (0.075-0.125 mm, 0.16-0.25 mm and 0.315-0.5 mm). The char yields were determined at two temperatures (900 and 1000 deg C) and the effects fuel to gas ratio (suspension density) as well as the effects of gas atmosphere were determined. Limited amount of tests were also carried out with pine wood and dried de-inking sludge. The formation of tars and nitrogen compounds was studied with peat as the feedstock. Based on the test results of this project and the on earlier fluidized-bed gasification data of VTT, the following conclusions can be made: (1) the char yields in rapid entrained flow pyrolysis of small particles of peat and biomass are considerably lower than derived in fluid-bed pyrolysis of more coarse feedstocks. Consequently, simple entrained flow reactors without any recycling of char could already give rather high carbon conversions. However, high carbon conversions can also be easily achieved in fluidized-bed gasifiers with biomass fuels due to the high gasification reactivity of the char, (2) more tars were formed in entrained flow pyrolysis of peat than in fluidized-bed experiments carried out at the same temperature, (3) the total conversion of peat nitrogen to NH{sub 3}+HCN was as high in the entrained flow pyrolysis as in the fluid-bed pyrolysis experiments. (Abstract Truncated)

Biomass, a 750 billion euros bet

International Nuclear Information System (INIS)

Remoue, A.

2010-01-01

Despite the check of its previous attempts to develop power generation from biomass fuels, the French government has announced the financing of 32 new projects of biomass fueled power plants representing 266 MW of additional power. Today's production represents 700 MW and the goal is to raise this production to 1230 MW by 2012 and 3530 MW by 2020. The development of biomass projects requires more important shareholders equity than wind power or solar energy projects and a good organization of the supply chain. (J.S.)

Biomass Burning Observation Project Science Plan

Energy Technology Data Exchange (ETDEWEB)

Kleinman, KI [Brookhaven National Laboratory; Sedlacek, AJ [Brookhaven National Laboratory

2013-09-01

Aerosols from biomass burning perturb Earth’s climate through the direct radiative effect (both scattering and absorption) and through influences on cloud formation and precipitation and the semi-direct effect. Despite much effort, quantities important to determining radiative forcing such as the mass absorption coefficients (MAC) of light-absorbing carbon, secondary organic aerosol (SOA) formation rates, and cloud condensation nuclei (CCN) activity remain in doubt. Field campaigns in northern temperate latitudes have been overwhelmingly devoted to other aerosol sources in spite of biomass burning producing about one-third of the fine particles (PM2.5) in the U.S.

EERC Center for Biomass Utilization 2006

Energy Technology Data Exchange (ETDEWEB)

Zygarlicke, Christopher J. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Hurley, John P. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Aulich, Ted R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Folkedahl, Bruce C. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Strege, Joshua R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Patel, Nikhil [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Shockey, Richard E. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center

2009-05-27

The Center for Biomass Utilization® 2006 project at the Energy & Environmental Research Center (EERC) consisted of three tasks related to applied fundamental research focused on converting biomass feedstocks to energy, liquid transportation fuels, and chemicals. Task 1, entitled Thermochemical Conversion of Biomass to Syngas and Chemical Feedstocks, involved three activities. Task 2, entitled Crop Oil Biorefinery Process Development, involved four activities. Task 3, entitled Management, Education, and Outreach, focused on overall project management and providing educational outreach related to biomass technologies through workshops and conferences.

Biomass changes and trophic amplification of plankton in a warmer ocean

KAUST Repository

Chust, Guillem; Allen, Julian Icarus; Bopp, Laurent; Schrum, Corinna; Holt, Jason T.; Tsiaras, Kostas P.; Zavatarelli, Marco; Chifflet, Marina; Cannaby, Heather; Dadou, Isabelle C.; Daewel, Ute; Wakelin, Sarah L.; Machú , Eric; Pushpadas, Dhanya; Butenschö n, Momme; Artioli, Yuri; Petihakis, George; Smith, Chris J M; Garç on, Vé ronique C.; Goubanova, Katerina; Le Vu, Briac; Fach, Bettina A.; Salihoglu, Baris; Clementi, Emanuela; Irigoien, Xabier

2014-01-01

Ocean warming can modify the ecophysiology and distribution of marine organisms, and relationships between species, with nonlinear interactions between ecosystem components potentially resulting in trophic amplification. Trophic amplification (or attenuation) describe the propagation of a hydroclimatic signal up the food web, causing magnification (or depression) of biomass values along one or more trophic pathways. We have employed 3-D coupled physical-biogeochemical models to explore ecosystem responses to climate change with a focus on trophic amplification. The response of phytoplankton and zooplankton to global climate-change projections, carried out with the IPSL Earth System Model by the end of the century, is analysed at global and regional basis, including European seas (NE Atlantic, Barents Sea, Baltic Sea, Black Sea, Bay of Biscay, Adriatic Sea, Aegean Sea) and the Eastern Boundary Upwelling System (Benguela). Results indicate that globally and in Atlantic Margin and North Sea, increased ocean stratification causes primary production and zooplankton biomass to decrease in response to a warming climate, whilst in the Barents, Baltic and Black Seas, primary production and zooplankton biomass increase. Projected warming characterized by an increase in sea surface temperature of 2.29 ± 0.05 °C leads to a reduction in zooplankton and phytoplankton biomasses of 11% and 6%, respectively. This suggests negative amplification of climate driven modifications of trophic level biomass through bottom-up control, leading to a reduced capacity of oceans to regulate climate through the biological carbon pump. Simulations suggest negative amplification is the dominant response across 47% of the ocean surface and prevails in the tropical oceans; whilst positive trophic amplification prevails in the Arctic and Antarctic oceans. Trophic attenuation is projected in temperate seas. Uncertainties in ocean plankton projections, associated to the use of single global and

Biomass changes and trophic amplification of plankton in a warmer ocean

KAUST Repository

Chust, Guillem

2014-05-07

Ocean warming can modify the ecophysiology and distribution of marine organisms, and relationships between species, with nonlinear interactions between ecosystem components potentially resulting in trophic amplification. Trophic amplification (or attenuation) describe the propagation of a hydroclimatic signal up the food web, causing magnification (or depression) of biomass values along one or more trophic pathways. We have employed 3-D coupled physical-biogeochemical models to explore ecosystem responses to climate change with a focus on trophic amplification. The response of phytoplankton and zooplankton to global climate-change projections, carried out with the IPSL Earth System Model by the end of the century, is analysed at global and regional basis, including European seas (NE Atlantic, Barents Sea, Baltic Sea, Black Sea, Bay of Biscay, Adriatic Sea, Aegean Sea) and the Eastern Boundary Upwelling System (Benguela). Results indicate that globally and in Atlantic Margin and North Sea, increased ocean stratification causes primary production and zooplankton biomass to decrease in response to a warming climate, whilst in the Barents, Baltic and Black Seas, primary production and zooplankton biomass increase. Projected warming characterized by an increase in sea surface temperature of 2.29 ± 0.05 °C leads to a reduction in zooplankton and phytoplankton biomasses of 11% and 6%, respectively. This suggests negative amplification of climate driven modifications of trophic level biomass through bottom-up control, leading to a reduced capacity of oceans to regulate climate through the biological carbon pump. Simulations suggest negative amplification is the dominant response across 47% of the ocean surface and prevails in the tropical oceans; whilst positive trophic amplification prevails in the Arctic and Antarctic oceans. Trophic attenuation is projected in temperate seas. Uncertainties in ocean plankton projections, associated to the use of single global and

Biomass changes and trophic amplification of plankton in a warmer ocean.

Science.gov (United States)

Chust, Guillem; Allen, J Icarus; Bopp, Laurent; Schrum, Corinna; Holt, Jason; Tsiaras, Kostas; Zavatarelli, Marco; Chifflet, Marina; Cannaby, Heather; Dadou, Isabelle; Daewel, Ute; Wakelin, Sarah L; Machu, Eric; Pushpadas, Dhanya; Butenschon, Momme; Artioli, Yuri; Petihakis, George; Smith, Chris; Garçon, Veronique; Goubanova, Katerina; Le Vu, Briac; Fach, Bettina A; Salihoglu, Baris; Clementi, Emanuela; Irigoien, Xabier

2014-07-01

Ocean warming can modify the ecophysiology and distribution of marine organisms, and relationships between species, with nonlinear interactions between ecosystem components potentially resulting in trophic amplification. Trophic amplification (or attenuation) describe the propagation of a hydroclimatic signal up the food web, causing magnification (or depression) of biomass values along one or more trophic pathways. We have employed 3-D coupled physical-biogeochemical models to explore ecosystem responses to climate change with a focus on trophic amplification. The response of phytoplankton and zooplankton to global climate-change projections, carried out with the IPSL Earth System Model by the end of the century, is analysed at global and regional basis, including European seas (NE Atlantic, Barents Sea, Baltic Sea, Black Sea, Bay of Biscay, Adriatic Sea, Aegean Sea) and the Eastern Boundary Upwelling System (Benguela). Results indicate that globally and in Atlantic Margin and North Sea, increased ocean stratification causes primary production and zooplankton biomass to decrease in response to a warming climate, whilst in the Barents, Baltic and Black Seas, primary production and zooplankton biomass increase. Projected warming characterized by an increase in sea surface temperature of 2.29 ± 0.05 °C leads to a reduction in zooplankton and phytoplankton biomasses of 11% and 6%, respectively. This suggests negative amplification of climate driven modifications of trophic level biomass through bottom-up control, leading to a reduced capacity of oceans to regulate climate through the biological carbon pump. Simulations suggest negative amplification is the dominant response across 47% of the ocean surface and prevails in the tropical oceans; whilst positive trophic amplification prevails in the Arctic and Antarctic oceans. Trophic attenuation is projected in temperate seas. Uncertainties in ocean plankton projections, associated to the use of single global and

SSCM analyses of biomass resources in Randers, Norddjurs and Syddjurs

Energy Technology Data Exchange (ETDEWEB)

2010-07-15

This project has been commissioned by ENERCOAST whose overall aim is to stimulate increased use and production of biomass, and create a market for bio energy in the North Sea region. The Enercoast project has been financed by the EU Interreg IVB with partners from Denmark, Germany, United Kingdom, Sweden and Norway. The Danish project leader is AgroBusiness Park/ CBMI /Innovation Centre for Bioenergy and Environmental Technology. Central Region Denmark is co-financing 34% of the Danish portion of the project, while the municipalities of Norddjurs, Syddjurs and Randers are contributing to the project with their working hours. The Danish portion of this project focuses on three Danish municipalities, Randers, Norddjurs, and Syddjurs, and the possibilities to reach local energy and climate targets by increasing the use and production of biomass. The project is divided into 6 phases of which this report is part of the second and third phase which focus on analyses of various biomass resources on a local level including carrying out SSCM analyses of these resources. The aim of this report is to assess the sustainability of relevant bio energy supply chains related to the resource accessibility in the three municipalities with main focus on biogas, straw, wood residues and energy crops for combined heat and power production. Sustainable Supply Chain Management (SSCM) is a concept that has many definitions and the methodologies used to approach this are numerous. In this report the SSCM analysis is used to answer the following question: What are the possibilities of increased use of biomass for energy production in the three municipalities, and what consequences are associated with the utilisation of each of the selected resources described through our case studies? For each of the resource case studies an overview of the supply chain is illustrated through a matrix. Each step of the supply chain from the primal material production in on end to heat and electricity

Outcome of UNIDO symposium on biomass energy

International Nuclear Information System (INIS)

Nazemi, A.H.

1997-01-01

The results of the UNIDO symposium are presented. The symposium covered a variety of subjects, beginning with a comparison of biomass energy production and potential uses in different regions, specific country case studies about the present situation and trends in biomass energy utilisation. Technological aspects discussed included the production of biomass resources, their conversion into energy carriers and technology transfer to developing countries. An analysis of financial resources available and mechanisms for funding biomass projects were given. Environmental effects and some relatively successful biomass projects under development were described. (K.A.)

Small-scale bioenergy projects in rural China: Lessons to be learnt

NARCIS (Netherlands)

Han, Jingyi; Mol, A.P.J.; Lu, Y.; Zhang, L.

2008-01-01

Large amounts of small-scale bioenergy projects were carried out in China's rural areas in light of its national renewable energy policies. These projects applied pyrolysis gasification as the main technology, which turns biomass waste at low costs into biogas. This paper selects seven bioenergy

Swiss Biomass Programme - Overview report on the 2007 research programme; Programm Biomasse: Ueberblicksbericht zum Forschungsprogramm 2007

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D; Guggisberg, B

2008-07-01

This illustrated report for the Swiss Federal Office of Energy (SFOE) presents an overview of the results obtained in 2007 within the framework of the Swiss Biomass research programme. The potential for biomass use in Switzerland is reviewed and the emphases of the national programme are discussed. The results obtained are noted for the following areas: process optimisation, including - amongst others - particle emissions and control aspects as well as combined wood-pellets and solar heating systems. Projects involving non-wood biomass are reported on, including biomass digesters and various biogas systems. Further reports deal with the analysis and optimisation of material flows, organic pollutants and methane losses. New conversion technologies are reported on. Further reports deal with basic strategies and concepts in the area of biomass usage. National and international co-operation is also discussed. A selection of innovative pilot and demonstration projects is also presented and research and development projects are listed.

ALTENER - Biomass event in Finland

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

ALTENER - Biomass event in Finland

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

Hydrogen from biomass

NARCIS (Netherlands)

Claassen, P.A.M.; Vrije, de G.J.

2006-01-01

Hydrogen is generally regarded as the energy carrier of the future. The development of a process for hydrogen production from biomass complies with the policy of the Dutch government to obtain more renewable energy from biomass. This report describes the progress of the BWP II project, phase 2 of

Production of biomass in wet peatlands (paludiculture). The EU-AID project 'Wetland energy' in Belarus. Solutions for the substitution of fossil fuels (peat briquettes) by biomass from wet peatlands

Energy Technology Data Exchange (ETDEWEB)

Wichtmann, Wendelin [Michael Succow Stiftung fuer den Schutz der Natur, Greifswald (Germany); Haberl, Andreas; Tanneberger, Franziska

2012-07-01

In Belarus, a pilot project demonstrating site adapted management of wet peatlands for biomass production have started recently. In cooperation with local stakeholders, the currently environmentally unfriendly peat extraction for energy will be converted into a sustainable land use system. By replacing the peat briquettes with locally produced briquettes using biomass from rewetted peatlands the income situation of remote and rural areas will be improved. In various combustion trials of peatland biomass in Germany and Belarus the suitability of the material for energy production has been demonstrated. The EU-Aid funded project in Belarus is realized by the Michael Succow Foundation in cooperation with the International Sacharov Environmental University (ISEU) and the Institute for Nature Management of the National Academy of Sciences (IfNM). Applied, site-specific management concepts, employing site adapted machinery for reed and sedge vegetation on wet peatlands will not only result in avoidance of environmentally harmful peat extraction, but also in benefits for distinctive biodiversity. This site adapted peatlands management (paludiculture) comprises the reduction of greenhousegas (GHG) emissions by rewetting of drained peatlands and by the replacement of fossil fuels by biomass from these sites. Under favourable conditions additionally CO{sub 2} sequestration by new peat formation reestablished. The biomass will be harvested with site adapted machinery and processed to fuel briquettes. (orig.)

Increasing the biomass production level of dedicated or semi-dedicated woody crops. Mains lessons learned from the SYLVABIOM project

International Nuclear Information System (INIS)

Bastien, Jean-Charles; Bodineau, Guillaume; Gauvin, Jean; Berthelot, Alain; Maine, Patrice; Brignolas, Franck; Maury, Stephane; Le Jan, Isabelle; Delaunay, Alain; Charnet, Francois; Merzeau, Dominique; Marron, Nicolas; Dalle, Erwin; Toillon, Julien

2015-01-01

For three species (poplar, black locust and willow) cultivated as short or very short rotation coppices (SRC/ VSRC), the project relied on monitoring growth and efficiency with which trees use water and nitrogen in a network of four experimental sites, located in contrasting stations. The relevance of DNA methylation levels as an early marker of the level of productivity was also evaluated. For short-rotation plantations (SRP), the project was based on the collection of growth and biomass data in experimental networks, to build compartmented biomass yield tables (trunk, bark, branches and leaves) for forest species for which the literature is scarce. Significant differences appear, both in SRC and VSRC, between the three species, and between intraspecific genotypes for biomass production, its phenology, architecture, leaf structure, and resource use efficiency. The pedo-climatic conditions and the planting density modulated the complex relationships between these traits. Measurement of apex or leaf DNA methylation rate may be a good predictor for the growth potential in poplar. Mean annual biomass production ranging from 7 to 13 dry tons/ha can be expected at age 20 years with fast-growing conifers grown in SRP on site types other than those used for SRC and VSRC. Moreover, very significant genetic gains on biomass production in SRP are also offered by selection of efficient genotypes. (authors)

Allometric equations for estimating tree biomass in restored mixed-species Atlantic Forest stands

Science.gov (United States)

Lauro Rodrigues Nogueira; Vera Lex Engel; John A. Parrotta; Antonio Carlos Galvão de Melo; Danilo Scorzoni Ré

2014-01-01

Restoration of Atlantic Forests is receiving increasing attention because of its role in both biodiversity conservation and carbon sequestration for global climate change mitigation. This study was carried out in an Atlantic Forest restoration project in the south-central region of São Paulo State – Brazil to develop allometric equations to estimate tree biomass of...

Insight on Biomass Supply and Feedstock Definition for Fischer-Tropsch Based BTL Processes

International Nuclear Information System (INIS)

Coignac, Julien

2013-01-01

Process chains of thermo chemical conversion of lignocellulosic biomass through gasification and Fischer-Tropsch synthesis (known as BTL) represent promising alternatives for biofuels production. Since biomass is heterogeneous and not homogeneously spread over territories, one of the major technological stakes of the project is to develop a flexible industrial chain capable of co-treating the widest possible range of biomass and fossil fuel feedstock. The present study aims at characterizing biomass diversity (availability and potentials by area, cost and mineral composition) by carrying out a state of the art, as a preliminary step in order to define a series of biomass to be tested in the demonstration plant and therefore define specifications for the process. Fifty different biomass were considered for their bio-energy application potential and were finally classified into four categories: agricultural by-products, dedicated energy crops, (Very) Short Rotation Coppice ((V)SRC) and forestry biomass. Biomass availability and potentials were investigated by the mean of a literature review of past and current projects (e.g. RENEW project, Biomass Energy Europe Project, etc.) and scientific articles. Most collected data are technical potentials, meaning that they take into account biophysical limits of crops and forests, technological possibilities, competition with other land uses and ecological constraints (e.g. natural reserves). Results show various emerging markets: North and South America have considerable amounts of agricultural by-products, forest residues, and large land areas which could be dedicated to energy crops; Africa shows relevant possibilities to grow Short Rotation Forestry (SRF) and energy crops; Russia has large available quantities of agricultural by-products and forest residues, as well as little valuable land where energy crops and SRC could be grown, and Asia shows relevant amounts of forest residues and possibilities of growing SRC, as well

Utilization of new feeding technology in power production from biomass; safety aspects and techno-economic assessment

Energy Technology Data Exchange (ETDEWEB)

Wilen, C.; Rautalin, A. [VTT Energy, Espoo (Finland)

1998-12-01

The possibility to prevent the dust explosions by suppression method in the ignition stage has been investigated in the project `Suppression of dust explosions in biomass-fired plants` (Bioenergy Research programme 1995). The first stage of the dust explosion and suppression tests under elevated pressure were carried out in spring 1996 in England using the 5.6 m{sup 3} equipment constructed for this purpose. The tests were carried out both with coal and wood dusts. The tests were carried out by Coal Technology Development Division (British Coal) and Kidde Fire Protection. In the first stage of the project it was possible to suppress both the coal and wood dust explosions successfully at the 10 bar pressure level. The target of the second stage of the project is to carry out the tests also at 18 bar pressure level. These tests would, if successful, enable the extrapolation of the operational parameters the pressure levels of 20-25 bars of IGCC plants. The limiting factors for the planning of pressurized (and ambient pressure) feeding systems are now known relatively well on the basis of the knowledge gained in the dust explosion and self-ignition tests, and the dust explosion suppression tests. The total objective of the research is the comparison of pressurized feeding systems, based mainly on the lock-hopper technology, both in the economical and technical sense. Arrangement of pressurization and sufficient inertization form a significant factor. The newest pressurized double-screw and piston feeder technologies will also be considered. The second stage of the suppression tests has been carried out in the first stage of the project. The suppression tests were successful both with coal and biomass dusts when using four suppression media containers. The full pressure dust explosions were carried out successfully at 18 bar initial pressure 4 refs., 2 figs., 1 tab. Bioenergy Research programme

Mapping the above and belowground biomass in three landscapes in Cameroon, Rwanda and DRC: pilot cases in REDD+ pilot project.

Science.gov (United States)

Sufo Kankeu, R.

2017-12-01

A number of biomass/carbon maps have been recently produced using different approaches and despite their comparison there is still a gap. To fill this gap there is a need to provide accurate maps based on the field data on all types of land use and land cover. Based on the field data from plots established in three pilot projects around Virunga National park in Rwanda, Tri-national Sangha landscape in Cameroon and lac Télé-Lac Tumba landscape in DRC, this paper intend to analyse the relationship between land use change and biomass and present the variability through biomass/carbon maps. The above and belowground biomass was calculated from 95 nested plots of 20 meters radius. The value of biomass/carbon per plot were thus used to elaborate carbon maps of each study site. In the same the way the correlation between the land use and underground and above ground carbon stock were analysed using geographically weighted regression. These data have been joint with classified Spot 5 image and aggregated to come out will acceptable result. Results show that there is a strong relationship between land use in various project sites and the carbon stock related, the change of a forest cover directly impact on carbon stock/biomass.in the same way carbon map realized base on field data and IDW, Kriging or spline module show an idea on the carbon distribution but the maps are not accurate giving the distance between plots,

FY 1999 report on the model project on the effective utilization of waste-base biomass fuels. Basic survey for the feasibility; 1999 nendo haikibutsukei biomass nenryo yuko riyo model jigyo jisshi kanosei kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey on the waste biomass was conducted for Thailand, Malaysia, Indonesia, Vietnam, Laos, Nepal, Butan, Myanmar and Cambodia to study feasibility of the project for the concrete utilization of biomass resources. In Thailand, it is expected to construct large-scale model plants for biomass resources such as rice hulls, bagasse, wood waste and oil palm. In Malaysia, expected are the cogeneration at 5MW class palm oil plant, large-scale power plant using wood waste, plant using the biomass from waste palm oil, etc. In Indonesia, there is a great potentiality, but it is necessary to handle it carefully in consideration of the unstable situation of the society. In Vietnam, the detailed survey of feasibility is needed on the project for efficiency heightening at state-run plants, the assumed national plants (recommended by the government), etc. In Laos, small-scale power generation using the forestry waste such as sawdust is expected. (NEDO)

Northeast Regional Biomass Program

Energy Technology Data Exchange (ETDEWEB)

O' Connell, R.A.

1991-11-01

The management structure and program objectives for the Northeast Regional Biomass Program (NRBP) remain unchanged from previous years. Additional funding was provided by the Bonneville Power Administration Regional Biomass Program to continue the publication of articles in the Biologue. The Western Area Power Administration and the Council of Great Lakes Governors funded the project Characterization of Emissions from Burning Woodwaste''. A grant for the ninth year was received from DOE. The Northeast Regional Biomass Steering Committee selected the following four projects for funding for the next fiscal year. (1) Wood Waste Utilization Conference, (2) Performance Evaluation of Wood Systems in Commercial Facilities, (3) Wood Energy Market Utilization Training, (4) Update of the Facility Directory.

Northeast Regional Biomass Program

International Nuclear Information System (INIS)

O'Connell, R.A.

1991-11-01

The management structure and program objectives for the Northeast Regional Biomass Program (NRBP) remain unchanged from previous years. Additional funding was provided by the Bonneville Power Administration Regional Biomass Program to continue the publication of articles in the Biologue. The Western Area Power Administration and the Council of Great Lakes Governors funded the project ''Characterization of Emissions from Burning Woodwaste''. A grant for the ninth year was received from DOE. The Northeast Regional Biomass Steering Committee selected the following four projects for funding for the next fiscal year. (1) Wood Waste Utilization Conference, (2) Performance Evaluation of Wood Systems in Commercial Facilities, (3) Wood Energy Market Utilization Training, (4) Update of the Facility Directory

Marketing research for energy from biomass in Europe; Marktverkenning voor energie uit biomassa in Europa

Energy Technology Data Exchange (ETDEWEB)

Rijpkema, B. [TNO Milieu, Energie en Procesinnovatie TNO-MEP, Apeldoorn (Netherlands); Van den Berg, P.; Vanb Haren, P. [Biomass Technology Group BTG, Enschede (Netherlands)

1997-07-01

Insight is given into the European market for energy from biomass, including information on plant size, most promising technologies, etc. These potentials may offer opportunities for manufacturers of energy generating systems. A quick scan of 23 European countries has been carried out as phase 1 of this project, which resulted in data, presented in the following format: General introduction; Existing energy infrastructure and structure of the energy demand; Price of fossil fuels, electricity and heat; Available biomass quantities; Prices of biomass; Installed biomass plants; Policy and regulations. Based on that information an overall conclusion was drawn for each country`s biomass energy situation. In phase 2 a more detailed survey has been executed for Estonia, Germany, Poland and Spain. The results of both phases are presented in a separate English report. This report is the result of phase 3 in which the results of phase 1 and 2 are evaluated to assess the possibilities for Dutch manufacturers of biomass energy systems

Biomass Energy | Climate Neutral Research Campuses | NREL

Science.gov (United States)

Biomass Energy Biomass Energy Biomass from local sources can be key to a campus climate action plan biomass may fit into your campus climate action plan. Campus Options Considerations Sample Project Related biomass fuels for energy does not add to the net amount of carbon in the atmosphere. This is because the

Energy balance of a wood biomass combustion process

International Nuclear Information System (INIS)

Baggio, P.; Cemin, A.; Grigiante, M.; Ragazzi, M.

2001-01-01

This article reports the results of a project developed at the University of Trent dealing with some wood biomass combustion processes. The project has been particularly dedicated to the study of the energetic analysis of the combustion processes that occur on a gasified wood stove of advanced combustion technologies. A considerable number of experimental tests has been carried out making use of different type of wood widely in use in Trentino region. The wood stove is a part of a pilot plant providing an hydraulic circuit equipped with a specific apparatus to measure all the necessary data to determine the energy balance required and specifically the thermal efficiency of the plant [it

Biomass Energy Generation Project

Energy Technology Data Exchange (ETDEWEB)

Olthoff, Edward [Cedar Falls Utilities, Cedar Falls, IA (United States)

2017-05-15

The Municipal Electric Utility of the City of Cedar Falls (dba Cedar Fals Utilities or CFU) received a congressionally directed grant funded through DOE-EERE to run three short (4 hour) duration test burns and one long (10 days) duration test burn to test the viability of renewable fuels in Streeter Station Boiler #6, a stoker coal fired electric generation unit. The long test burn was intended to test supply chain assumptions, optimize boiler combustion and assess the effects of a longer duration burn of biomass on the boiler.

Private capital requirements for international biomass energy projects

Energy Technology Data Exchange (ETDEWEB)

Goldemberg, J [University of Sao Paulo, Sao Paulo (Brazil)

1995-12-01

In developing countries, the use of biomass for energy production faces two contradictory pressures. On the one hand, biomass costs very little and it is used inefficiently for fuel or charcoal production, leading to widespread destruction of forested areas and environmental degradation; this problem is being attenuated by the promotion, through aid programmes, of more efficient cook stoves for poor people. On the other hand, the conversion of biomass into high-grade fuel such as ethanol from sugar cane or burning urban refuse or gasifying it to produce electricity is not economically competitive at this time and requires subsidies of approximately 30% to make it as attractive as conventional fuels. Only electricity production using residues from sawmills, crops and other biomass by-products is competitive, and a number of plants are in operation in some countries, particularly the United States. For such plants, the usual rates of return and long-term contract purchases that characterize investments of this kind are applied. Although technologies are available for the widespread efficient use of biomass, the financial hurdle of high initial costs has impeded their market penetration, which in turn precludes any decline in costs that might otherwise have come from production increases. Intervention by governments or by GEF, justified on grounds of environmental protection, is needed to accelerate the introduction of the new technologies. The only private flows that are taking place at the moment are those from enlightened investors wishing to guarantee themselves a strong position in the area for the future or to preempt command and control regulations, such as carbon taxes, imposed by governments. The joint implementation of biomass technologies between industrialized and developing countries might be one method of accelerating this flow. (author) 9 refs, 4 figs, 3 tabs

Private capital requirements for international biomass energy projects

International Nuclear Information System (INIS)

Goldemberg, J.

1995-01-01

In developing countries, the use of biomass for energy production faces two contradictory pressures. On the one hand, biomass costs very little and it is used inefficiently for fuel or charcoal production, leading to widespread destruction of forested areas and environmental degradation; this problem is being attenuated by the promotion, through aid programmes, of more efficient cook stoves for poor people. On the other hand, the conversion of biomass into high-grade fuel such as ethanol from sugar cane or burning urban refuse or gasifying it to produce electricity is not economically competitive at this time and requires subsidies of approximately 30% to make it as attractive as conventional fuels. Only electricity production using residues from sawmills, crops and other biomass by-products is competitive, and a number of plants are in operation in some countries, particularly the United States. For such plants, the usual rates of return and long-term contract purchases that characterize investments of this kind are applied. Although technologies are available for the widespread efficient use of biomass, the financial hurdle of high initial costs has impeded their market penetration, which in turn precludes any decline in costs that might otherwise have come from production increases. Intervention by governments or by GEF, justified on grounds of environmental protection, is needed to accelerate the introduction of the new technologies. The only private flows that are taking place at the moment are those from enlightened investors wishing to guarantee themselves a strong position in the area for the future or to preempt command and control regulations, such as carbon taxes, imposed by governments. The joint implementation of biomass technologies between industrialized and developing countries might be one method of accelerating this flow. (author)

Process and apparatus for conversion of biomass

NARCIS (Netherlands)

Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

2006-01-01

The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into

WOOD BIOMASS FOR ENERGY IN MONTENEGRO

Directory of Open Access Journals (Sweden)

Gradimir Danon

2010-01-01

Full Text Available Wood biomass has got its place in the energy balance of Montenegro. A little more than 6% of the total energy consumption is obtained by burning wood. Along with the appropriate state measures, it is economically and environmentally justified to expect Montenegro to more than double the utilization of the existing renewable energy sources including wood biomass, in the near future. For the purpose of achieving this goal, ‘Commercial Utilisation of the Wood Residue as a Resource for Economic Development in the North of Montenegro' project was carried out in 2007. The results of this project were included in the plan of the necessary interventions of the Government and its Agencies, associations or clusters, non-government organisations and interested enterprises. The plan was made on the basis of the wood residue at disposal and the attitude of individual subjects to produce and/or use solid bio-fuels and consists of a proposal of collection and utilisation of the wood residue for each individual district in the north of Montenegro. The basic factors of sustainability of future commercialisation of the wood residue were: availability of the wood raw material, and thereby the wood residue; the development of wood-based fuel markets, and the size of the profit.

Proceedings of the fifth International Slovak Biomass Forum (ISBF)

International Nuclear Information System (INIS)

2005-02-01

The publication has been set up as a proceedings of the conference dealing with use of biomass for energy production. The main conference topics are focused on the following scopes: Session 1: RES Policies, strategies, political background; Session 2: Bioenergy markets, tools and influence factors; Session 3: Biomass fuels production and trading; Parallel Session 4: Biomass firing technologies; Parallel Session 5: Municipal projects uptake; Parallel Session 6: Biomass large and small CHP; Parallel Session 7: Environmental biomass technologies; Session 8: Biomass projects financing roundtable; In this proceedings 54 contributions is included

Fundamentals of Biomass pellet production

DEFF Research Database (Denmark)

Holm, Jens Kai; Henriksen, Ulrik Birk; Hustad, Johan Einar

2005-01-01

Pelletizing experiments along with modelling of the pelletizing process have been carried out with the aim of understanding the fundamental physico-chemical mechanisms that control the quality and durability of biomass pellets. A small-scale California pellet mill (25 kg/h) located with the Biomass...

Trading biomass or GHG emission credits?

NARCIS (Netherlands)

Laurijssen, J; Faaij, A.P.C.

2009-01-01

Global biomass potentials are considerable but unequally distributed over the world. Countries with Kyoto targets could import biomass to substitute for fossil fuels or invest in bio-energy projects in the country of biomass origin and buy the credits (Clean Development Mechanism (CDM) and Joint

Evaluation of the FEERv1.0 Global Top-Down Biomass Burning Emissions Inventory over Africa

Science.gov (United States)

Ellison, L.; Ichoku, C. M.

2014-12-01

With the advent of the Fire Energetics and Emissions Research (FEER) global top-down biomass burning emissions product from NASA Goddard Space Flight Center, a subsequent effort is going on to analyze and evaluate some of the main (particulate and gaseous) constituents of this emissions inventory against other inventories of biomass burning emissions over the African continent. There is consistent and continual burning during the dry season in NSSA of many small slash-and-burn fires that, though may be relatively small fires individually, collectively contribute 20-25% of the global total carbon emissions from biomass burning. As a top-down method of estimating biomass-burning emissions, FEERv1.0 is able to yield higher and more realistic emissions than previously obtainable using bottom-up methods. Results of such comparisons performed in detail over Africa will be discussed in this presentation. This effort is carried out in conjunction with a NASA-funded interdisciplinary research project investigating the effects of biomass burning on the regional climate system in Northern Sub-Saharan Africa (NSSA). Essentially, that project aims to determine how fires may have affected the severe droughts that plagued the NSSA region in recent history. Therefore, it is imperative that the biomass burning emissions input data over Africa be as accurate as possible in order to obtain a confident understanding of their interactions and feedbacks with the hydrological cycle in NSSA.

Performance of HT-WGS Catalysts for Upgrading of Syngas Obtained from Biomass Gasification

Energy Technology Data Exchange (ETDEWEB)

Marano Bujan, M.; Sanchez Hervas, J. M.

2009-05-21

Oxygen pressurized gasification of biomass out stands as a very promising approach to obtain energy or hydrogen from renewable sources. The technical feasibility of this technology is being investigated under the scope of the VI FP CHRISGAS project, which has started in September 2004 and has a duration of five years. The Division of Combustion and Gasification of CIEMAT participates in this project in Work Package 13: Ancillary and novel processes, studying innovative gas separation and gas upgrading systems. Such systems include novel or available high temperature water gas shift catalysts and commercially available membranes not yet tried in this type of atmosphere. This report describes the activities carried out during the period 2005-2007 regarding the performance of high temperature water gas shift catalysts for upgrading of synthesis gas obtained from biomass gasification. (Author) 28 refs.

42 CFR 137.291 - May Self-Governance Tribes carry out construction projects without assuming these Federal...

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false May Self-Governance Tribes carry out construction... OF HEALTH AND HUMAN SERVICES TRIBAL SELF-GOVERNANCE Construction Nepa Process § 137.291 May Self-Governance Tribes carry out construction projects without assuming these Federal environmental...

Sustainability of Biomass Utilisation in Changing operational Environment - SUBICHOE

Energy Technology Data Exchange (ETDEWEB)

Soimakallio, S.; Hongisto, M.; Koponen, K. (VTT Technical Research Centre of Finland, Espoo (Finland)), e-mail: sampo.soimakallio@vtt.fi (and others)

2011-11-15

Sustainability is a multi-faceted and challenging target, but at the same time a crucial issue to assess when setting policies and targets for the future. The main objective of the SUBICHOE project is to assist public administration and companies in strategic decision- making in the most sustainable use of biomass, by taking into account the changing operational environment. The project aimed to assess how the sustainability criteria, in particular those set by the EC, ensure the sustainability of biofuels from short and long term perspectives. The project is carried out jointly by VTT Technical Research Centre of Finland, Finnish Environment Institute SYKE, MTT Agrifood Research Finland, Finnish Forest Research Institute (Metla) and The Government Institute for Economic Research (VATT). The work plan of the project is divided into four Work Packages. In this article, a summary of main findings of the project is presented. (orig.)

Suppression of dust explosions and ignition spots in biomass-fired power plants

Energy Technology Data Exchange (ETDEWEB)

Wilen, C.; Rautalin, A.

1995-12-31

Dust explosion characteristics of forest residue dust both at normal pressure and at elevated initial pressure have been determined in previous studies. These indices give a good base for evaluating the usability of suppression systems to obtain a sufficient level of peritoneal safety in biomass fuel handling equipment. The objectives of this project were to evaluate the usability of suppression systems and to demonstrate dust explosion suppression at elevated initial pressure. Suppression tests at 1 - 20 bar pressure will be carried out in co-operation with CTDD of British Coal, Kiddy Fire Protection and Health and Safety Executive. The tests with coal and biomass dust are scheduled to be started in March 1996 in Great Britain. In the second task of the project, self-ignition properties of forest residue dust and straw dust have been measured in a flow-through system simulating slow drying of the fuel

Suppression of dust explosions and ignition spots in biomass-fired power plants

Energy Technology Data Exchange (ETDEWEB)

Wilen, C; Rautalin, A

1996-12-31

Dust explosion characteristics of forest residue dust both at normal pressure and at elevated initial pressure have been determined in previous studies. These indices give a good base for evaluating the usability of suppression systems to obtain a sufficient level of peritoneal safety in biomass fuel handling equipment. The objectives of this project were to evaluate the usability of suppression systems and to demonstrate dust explosion suppression at elevated initial pressure. Suppression tests at 1 - 20 bar pressure will be carried out in co-operation with CTDD of British Coal, Kiddy Fire Protection and Health and Safety Executive. The tests with coal and biomass dust are scheduled to be started in March 1996 in Great Britain. In the second task of the project, self-ignition properties of forest residue dust and straw dust have been measured in a flow-through system simulating slow drying of the fuel

Suppression of dust explosions and ignition spots in biomass- fired power plants

Energy Technology Data Exchange (ETDEWEB)

Wilen, C; Rautalin, A [VTT Energy, Espoo (Finland)

1997-12-01

Dust explosion characteristics of forest residue dust both at normal pressure and at elevated initial pressure have been determined in previous studies. These indices give a good base for evaluating the usability of suppression systems to obtain a sufficient level of operational safety in biomass fuel handling equipment. The objectives of this project were to evaluate the usability of suppression systems and to demonstrate dust explosion suppression at elevated initial pressure. Suppression tests at 1 - 20 bar pressure will be carried out in co-operation with CTDD of British Coal, Kiddy Fire Protection and Health and Safety Executive. The tests with coal and biomass dust are scheduled to be started in March 1996 in Great Britain. In the second task of the project, self-ignition properties of forest residue dust and straw dust have been measured in a flow-through system simulating slow drying of the fuel

Decision analysis for the determination of biomass in the territory Tuscia Romana by geographic information system and forest management plans

Directory of Open Access Journals (Sweden)

A. Colantoni

2013-09-01

Full Text Available The growing interest in the development of chains for the use of agroforestry biomass for energy demand, is due to the awareness they are a crucial element to mitigate the global climatic change effects. The true effort is to have a reliable estimation of biomass availability by some instruments like forest management plans, which allow to locate the forest supply and to know the forest biomass availability in a medium period. In this paper we carried out a decision analysis by geographic information system, in Tuscia Romana area comprising 11 municipalities for a total amount of 813 km2. An estimation was carried out taking into account the bibliographic data on the analyzed species, reporting the biomass in weight taken out by the forest cut utilization. A comparison was also performed in field on chestnut trees cut in a sampling area near Bracciano and in a close sawmill. The results show long, medium and short-term dynamics, but some critical points were found related to the process of estimation and to the real procurement of biomass in some years. The results suggest to be care in a possible project of a biomass plant.

The biomass file

International Nuclear Information System (INIS)

2010-01-01

As biomass represents the main source of renewable energy to reach the 23 per cent objective in terms of energy consumption by 2020, a first article gives a synthetic overview of its definition, its origins, its possible uses, its share in the French energy mix, its role by 2020, strengths and weaknesses for its development, the growth potential of its market, and its implications in terms of employment. A second article outlines the assets of biomass, indicates the share of some crops in biomass energy production, and discusses the development of new resources and the possible energy valorisation of various by-products. Interviews about biomass market and development perspectives are proposed with representatives of institutions, energy industries and professional bodies concerned with biomass development and production. Other articles comments the slow development of biomass-based cogeneration, the coming into operation of a demonstration biomass roasting installation in Pau (France), the development potential of biogas in France, the project of bio natural gas vehicles in Lille, and the large development of biogas in Germany

Carbon carry capacity and carbon sequestration potential in China based on an integrated analysis of mature forest biomass.

Science.gov (United States)

Liu, YingChun; Yu, GuiRui; Wang, QiuFeng; Zhang, YangJian; Xu, ZeHong

2014-12-01

Forests play an important role in acting as a carbon sink of terrestrial ecosystem. Although global forests have huge carbon carrying capacity (CCC) and carbon sequestration potential (CSP), there were few quantification reports on Chinese forests. We collected and compiled a forest biomass dataset of China, a total of 5841 sites, based on forest inventory and literature search results. From the dataset we extracted 338 sites with forests aged over 80 years, a threshold for defining mature forest, to establish the mature forest biomass dataset. After analyzing the spatial pattern of the carbon density of Chinese mature forests and its controlling factors, we used carbon density of mature forests as the reference level, and conservatively estimated the CCC of the forests in China by interpolation methods of Regression Kriging, Inverse Distance Weighted and Partial Thin Plate Smoothing Spline. Combining with the sixth National Forest Resources Inventory, we also estimated the forest CSP. The results revealed positive relationships between carbon density of mature forests and temperature, precipitation and stand age, and the horizontal and elevational patterns of carbon density of mature forests can be well predicted by temperature and precipitation. The total CCC and CSP of the existing forests are 19.87 and 13.86 Pg C, respectively. Subtropical forests would have more CCC and CSP than other biomes. Consequently, relying on forests to uptake carbon by decreasing disturbance on forests would be an alternative approach for mitigating greenhouse gas concentration effects besides afforestation and reforestation.

Developing business in emerging biomass energy markets

International Nuclear Information System (INIS)

Kadyszewski, J.

2005-01-01

Global market trends for forest products were reviewed in this PowerPoint presentation. The status of biomass energy products in relation to climate change and renewable energy portfolio standards was also examined. It was noted that China has increased investment in processing capacity and has increased imports of raw logs. India has doubled its imports of raw logs. Details of major tropical log producers and consumers were presented. Details of the biomass industry in the United States were presented, as well as data on fuel use at biomass energy plants and biomass energy capacity. An overview of biomass energy in the Russian far east and Siberia was presented, as well as details of activities and opportunities in Brazil and Indonesia. An economic analysis for small dry kilns was presented. Issues concerning boiler capacity in Russian companies for 2001-2005 were discussed. A case study of a biomass project from Congo was presented. It was noted that projects that replace fossil fuels can obtain revenues from the sale of carbon benefits, and that biomass energy offers the most attractive current option for the removal of carbon dioxide (CO 2 ) from the atmosphere. Details of a district heating project in Siberia were presented, and it was noted that in remote regions, costs for heat and power from biomass can be lower than costs from diesel and coal. It was concluded that there will be significant growth for biomass energy systems in the developing world, and that climate change will be an increasingly important element in advancing biomass energy. tabs., figs

Biomass feedstock analyses

Energy Technology Data Exchange (ETDEWEB)

Wilen, C.; Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

1996-12-31

The overall objectives of the project `Feasibility of electricity production from biomass by pressurized gasification systems` within the EC Research Programme JOULE II were to evaluate the potential of advanced power production systems based on biomass gasification and to study the technical and economic feasibility of these new processes with different type of biomass feed stocks. This report was prepared as part of this R and D project. The objectives of this task were to perform fuel analyses of potential woody and herbaceous biomasses with specific regard to the gasification properties of the selected feed stocks. The analyses of 15 Scandinavian and European biomass feed stock included density, proximate and ultimate analyses, trace compounds, ash composition and fusion behaviour in oxidizing and reducing atmospheres. The wood-derived fuels, such as whole-tree chips, forest residues, bark and to some extent willow, can be expected to have good gasification properties. Difficulties caused by ash fusion and sintering in straw combustion and gasification are generally known. The ash and alkali metal contents of the European biomasses harvested in Italy resembled those of the Nordic straws, and it is expected that they behave to a great extent as straw in gasification. Any direct relation between the ash fusion behavior (determined according to the standard method) and, for instance, the alkali metal content was not found in the laboratory determinations. A more profound characterisation of the fuels would require gasification experiments in a thermobalance and a PDU (Process development Unit) rig. (orig.) (10 refs.)

Influence of forest biomass grown in fertilised soils on combustion and gasification processes as well as on the environment with integrated bioenergy production

Energy Technology Data Exchange (ETDEWEB)

Jaanu, K; Orjala, M [VTT Energy, Jyvaeskylae (Finland). Fuel Production

1997-12-01

This presentation describes research carried out by VTT Energy and METLA during 1996, as part of the collaborative EU project involving Finland, Portugal and Spain. The main objectives of this project are to carry out experimental studies of both combustion and gasification under atmospheric (Portugal and Spain) and pressurised conditions (Finland) using biomass from different countries, namely Finland, Portugal and Spain. This was to determine the influence of biomass fertilising conditions on the process itself and the impact on the integrated energy production facilities, such as gas turbines. The aim of the research was carried out during 1996: (1) To complete the biomass collection, analyses and selection of the samples for combustion and gasification tests. This task has been carried out in co-operation with VTT and METLA, (2) To start the combustion and gasification tests under pressurised and atmospheric conditions. The combustion research in Finland is being performed in pressurised entrained flow reactor at VTT in Jyvaeskylae and the gasification research is being conducted at VTT in Espoo. The collection of biomass samples has been completed. The analyses of the samples show that for instance potassium and phosphorus content will be increased by about 30-50 % due to fertilisation. In the ash fusion tests, the ash from fertilised bark and branches and needles may start to soften already at 900 deg C under reducing conditions depending on the composition of the ash. In oxidising atmospheres the ash softening seems to occur at higher temperatures. Preliminary results indicate that the fertilisation may have an influence on the combustion process

Carrying capacity of Chaetoceros gracilis in Homa Lagoon and the ...

African Journals Online (AJOL)

The possibility for nutrient limitation to affect C. gracilis was assessed from two different ecosystems (Izmir Bay and Homa Lagoon). Our goal was to determine the growth rate of all nutrients and the maximum levels of the C. gracilis phytoplankton biomass (the maximum biomass carrying capacity) on the extent of its full ...

Process and apparatus for the conversion of biomass

NARCIS (Netherlands)

Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

2008-01-01

The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into

Potential for Coal Power Plants to Co-Fire with Woody Biomass in the U. S. North, 2010-2030: A Technical Document Supporting the Northern Forest Futures Project

Science.gov (United States)

Michael E. Goerndt; Francisco X. Aguilar; Kenneth E. Skog

2015-01-01

Future use of woody biomass to produce electric power in the U.S. North can have an important influence on timber production, carbon storage in forests, and net carbon emissions from producing electric power. The Northern Forest Futures Project (NFFP) has provided regional- and state-level projections of standing forest biomass, land-use change, and timber harvest,...

Biomass burning studies and the International Global Atmospheric Chemistry (IGAC) Project

International Nuclear Information System (INIS)

Prinn, R.G.

1991-01-01

The perturbations to local and regional atmospheric chemistry caused by biomass burning also have global significance. The International Global Atmospheric Chemistry (IGAC) Project was created by scientists from over twenty countries in response to the growing interest concern about atmospheric chemical changes and their potential impact on mankind. The goal of the IGAC is to develop a fundamental understanding of the natural and anthropogenic processes that determine the chemical composition of the atmosphere and the interactions between atmospheric composition and biospheric and climatic processes. A specific objective is to accurately predict changes over the next century in the composition and chemistry of the global atmosphere. Current activities, leaders and scientists involved are presented in this chapter

Sustainable biomass products development and evaluation, Hamakua project. Final draft report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The PICHTR Sustainable Biomass Energy Program was developed to evaluate the potential to cultivate crops for energy production as an alternative use of lands made available by the closing of large sugar plantations. In particular, the closing of the Hamakua Sugar Company on the island of Hawaii brought a great deal of attention to the future of agriculture in this region and in the state. Many options were proposed. Several promising alternatives had been proposed for cane lands. These included dedicated feedstock supply systems (DFSS) for electrical energy production, cultivation of sugarcane to produce ethanol and related by-products, and the production of feed and crops to support animal agriculture. Implementation of some of the options might require preservation of large tracts of land and maintenance of the sugar mills and sugar infrastructure. An analysis of the technical, financial, and other issues necessary to reach conclusions regarding the optimal use of these lands was required. At the request of the Office of State Planning and Senator Akaka`s office, the Pacific International Center for High Technology Research (PICHTR) established and coordinated a working group composed of state, county, federal, and private sector representatives to identify sustainable energy options for the use of idle sugar lands on the island of Hawaii. The Sustainable Biomass Energy Program`s Hamakua Project was established to complete a comprehensive evaluation of the most viable alternatives and assess the options to grow crops as a source of raw materials for the production of transportation fuel and/or electricity on the island of Hawaii. The motivation for evaluating biomass to energy conversion embraced the considerations that Hawaii`s energy security would be improved by diversifying the fuels used for transportation and reducing dependency on imported fossil fuels. The use of waste products as feedstocks could divert wastes from landfills.

Availability of biomass for energy: Report of the contractors meeting, held at November 3, 1994, in Utrecht, Netherlands

International Nuclear Information System (INIS)

De Jager, D.

1994-11-01

Results of a few studies on the title subject, carried out within the framework of the NOVEM programme EWAB, were presented at a contractors meeting. The overall conclusion of the presentation was that energy from biomass has a large potential. However, the cost effectiveness of the different options has to be improved. In particular, international research on the subject is necessary. Also more demonstration projects have to be set up in order to gain insight in the exact costs and benefits, the options to improve the cost-effectiveness, and to fill in the knowledge gaps. In the presentations of the meeting attention is paid to avoided CO 2 emissions as a result of energy crops, the spatial aspects of biomass cultivation, model calculations of the economics of biomass techniques in comparison with other techniques, conversion techniques for biomass, biomass harvesting systems, logistic aspects regarding energy production from biomass, experiences with the cultivation of willows and miscanthus, the cost effectiveness of biomass cultivation, and the state-of-the-art in national and international research on energy from biomass

Biomass as a fuel: Advantages, limitations and possibilities

International Nuclear Information System (INIS)

McBurney, B.

1997-01-01

This presentation briefly outlines major issues related to the use of biomass fuels. Advantages and disadvantages of biomass fuels are identified, as well as major factors that may facilitate greater use of biomass fuels. Highlights of the US DOE Biomass Power Program, program activities, and demonstration projects are presented. Some statistical and economic data are provided, including biomass fueled electric capacity, biomass energy consumption by sector, and fuel cost savings and greenhouse gas emissions reductions for four biomass co-fired units

Demonstration of Pressurizing Coal/Biomass Mixtures Using Posimetric Solids Pump Technology

Energy Technology Data Exchange (ETDEWEB)

Westendorf, Tiffany; Acharya, Harish; Cui, Zhe; Furman, Anthony; Giammattei, Mark; Rader, Jeff; Vazquez, Arturo

2012-12-31

This document is the Final Technical Report for a project supported by U.S. DOE NETL (Contract No. DE-FE0000507), GE Global Research, GE Energy, and Idaho National Laboratory (INL). This report discusses key project accomplishments for the period beginning August 7, 2009 and ending December 31, 2012. In this project, pressurized delivery of coal/biomass mixtures using GE Posimetric* solids pump technology was achieved in pilot scale experiments. Coal/biomass mixtures containing 10-50 wt% biomass were fed against pressures of 65-450 psi. Pressure capability increased with decreasing biomass content for a given pump design, and was linked to the interaction of highly compressible coal/biomass mixtures with the pump outlet design. Biomass pretreatment specifications for particle size and moisture content were defined based on bench-scale flowability, compressibility, friction, and permeability experiments that mimic the behavior of the Posimetric pump. A preliminary economic assessment of biomass pretreatment and pump operation for coal/biomass mixtures (CBMs) was conducted.

Characterization of biomass producer gas as fuel for stationary gas engines in combined heat and power production

DEFF Research Database (Denmark)

Ahrenfeldt, Jesper

2008-01-01

The aim of this project has been the characterization of biomass producer gas as a fuel for stationary gas engines in heat and power production. More than 3200 hours of gas engine operation, with producer gas as fuel, has been conducted at the biomass gasification combined heat and power (CHP...... different measuring methods. Likewise, no particles were detected in the gas. Considerable amounts of NH3 were measured in the produced gas.An analysis of engine operation at varying load has been carried out. Standard emissions, load and efficiency have been measured at varying operating conditions ranging...... from 50% to 90% load. Biomass producer gas is an excellent lean burn engine fuel: Operation of a natural aspirated engine has been achieved for 1.2...

Biomass programme: Overview of the 2006 Swiss research programme; Programm Biomasse. Ueberblicksbericht zum Forschungsprogramm 2006

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D.; Guggisberg, B.

2007-07-01

This report for the Swiss Federal Office of Energy (SFOE) reviews work done within the framework of the Swiss biomass research programme in 2006. The programme concentrates on the efficient conversion of biomass into heat, electrical power and motor fuels. Projects concerned with the optimisation of processes are reported on, including low-particle-emission systems, control systems for bivalent heating installations, use of demanding biomass fuels, combined pellets and solar heating systems and the elimination of ammonia emissions. In the material flow area, measurement campaigns, organic pollutants in compost, the effects of fermented wastes in agriculture and methane losses in biogas conditioning are reported on. New conversion technologies are reviewed, including hydro-thermal gasification, plant-oil fuelled combined heat and power units, flameless burners and catalytic direct liquefaction. In the area of basics, studies and concepts, eco-balances and life-cycle analyses are reported on; the production of synthetic natural gas and the influence of combustion particles are discussed and decentralised power generation from solid biomass is reported on. National and international co-operation is reviewed. The report is concluded with a review of eight pilot and demonstration projects, a review of work to be done in 2007 and a list of research and demonstration projects.

Establishing biomass heating in the UK: phase 2

International Nuclear Information System (INIS)

2000-01-01

The Biomass Heat Working Group, first set up in 1995, was taken on by British BioGen in 1996. Over the summer of 1996 British BioGen, supported by DTI, worked with the group to produce 'A Strategy to Develop the UK Market for Biomass Heating Installations'. In the spring of 1997 British BioGen agreed a two-year programme with ETSU (for the DTI) to 'Establish Biomass Heating in the UK'. The DTI's New and Renewable Energy Programme has supported this two-year programme which aims to bring together industry stakeholders and assist in the development of a significant biomass heat market in the UK. Overall we believe the project has been successful in its aim to increase the volume of biomass heating enquiries and enable greater use of the industry 'knowledge base'. Throughout the duration of the project a number of new biomass heating systems have been installed, including Shenstone Lodge School, Boughton Pumping Station and Elvendon Priory. In addition, an efficient system of information exchange has been established for customers and industry. British BioGen believe that the benefits of this system will be a crucial factor in achieving bioenergy industry targets of 2MWt for domestic heating, 2MWt for industrial and commercial heating and 2MWt for CHP by the end of 2001. The remainder of this summary offers highlights of the activities undertaken within the project, outlines the conclusions of the project and makes brief recommendations for further actions to assist the further deployment of biomass heating in the UK. (author)

Biomass fuelled indirect fired micro turbine

Energy Technology Data Exchange (ETDEWEB)

Pritchard, D.

2005-07-01

This report summarises the findings of a project to further develop and improve a system based on the Bowman TG50 50kWe turbine and a C3(S) combustor with a high temperature heat exchanger for the production of electricity from biomass. Details are given of the specific aims of the project, the manufacture of a new larger biomass combustor, the development of startup and shutdown procedures, waste heat recuperation, adaption of a PC-based mathematical model, and capital equipment costs. The significant levels of carbon emission savings and the commercial prospects of the biomass generator gas turbine combined heat and power (CHP) system are considered, and recommendations are presented.

Introduction to the Biomass Project: An Illustration of Evidence-Centered Assessment Design and Delivery Capability. CSE Report.

Science.gov (United States)

Steinberg, Linda S.; Mislevy, Robert J.; Almond, Russell G.; Baird, Andrew B.; Cahallan, Cara; Dibello, Louis V.; Senturk, Deniz; Yan, Duanli; Chernick, Howard; Kindfield, Ann C. H.

This paper describes the design rationale for a prototype of an innovative assessment product, and the process that led to the design. The goals of the Biomass project were to demonstrate: (1) an assessment product designed to serve two new purposes in the transition from high school to college; and (2) the capability needed to produce this kind…

Biomass combustion gas turbine CHP

Energy Technology Data Exchange (ETDEWEB)

Pritchard, D.

2002-07-01

This report summarises the results of a project to develop a small scale biomass combustor generating system using a biomass combustor and a micro-gas turbine indirectly fired via a high temperature heat exchanger. Details are given of the specification of commercially available micro-turbines, the manufacture of a biomass converter, the development of a mathematical model to predict the compatibility of the combustor and the heat exchanger with various compressors and turbines, and the utilisation of waste heat for the turbine exhaust.

Robust and sustainable bioenergy: Biomass in the future Danish energy system; Robust og baeredygtig bioenergi: Biomasse i fremtidens danske energisystem

Energy Technology Data Exchange (ETDEWEB)

Skoett, T.

2012-09-15

The publication is a collection of articles about new, exciting technologies for the production of bioenergy, which received support from Danish research programmes. The green technologies must be sustainable so that future generations' opportunities for bioenergy use is not restricted, and the solutions must be robust in relation to security of supply, costs and energy economy. In this context, research plays a crucial role. Research is especially carried out within the use of residues as bio-waste, straw, wood and manure for energy purposes, but there are also projects on energy crops, as well as research into how algae from the sea can increase the production of biomass. (LN)

EUBIONET II. Efficient trading of biomass fuels and analysis of fuel supply chains and business models for market actors by networking. Final result-oriented report

Energy Technology Data Exchange (ETDEWEB)

Alakangas, E.; Wiik, C.; Vesterinen, P. (and others)

2008-02-15

The project aimed to increase deployment of biomass fuels into European market and match technology uptake by means of market and policy analysis and other well-defined tasks to meet European policy targets in renewable energy sector. The project is to result as increased use of biomass fuels and market uptake of innovative bioenergy technologies. The objectives of the project were the following: 1) To give a clear outlook on current and future biomass fuel market trends. 2) To give feedback on the suitability of CEN 335 biofuel standard for trading of solid biofuels. 3) To provide well-analysed estimation on techno-economic potential of the biomass fuel volumes until 2010 based on the existing studies and experts opinions. Regarding the forest biomass sector, co-operation will be done with forest industry stakeholders to find proper balance between forest industry raw material and bioenergy usage. 4) To enhance biomass fuel trade and technology transfer by networking among different actors. 5) To analyse, select and describe the most suitable trading and business models for small- and largescale biofuel supply chains for heat and power production by taking into account the environmental aspects and sustainability. 6) To enhance biomass usage by the means of co-operation and information dissemination among different market actors in the fuel-utilisation chain. Target groups were biomass fuel traders and users, fuel producers and suppliers of different scales, policy makers in both current and new member states. Key associations, i.e. AEBIOM and CEPI, were participating in the project and disseminating information to various groups. The project has been structured in 5 workpackages. Project was carried out by 16 partners, which are the key national bioenergy organisations in the European countries and have a long co-operation relationship in previous bioenergy networks. The project has published summary reports and national report of each WP and this report is

Availability of waste and biomass for energy generation in the Netherlands; Beschikbaarheid van afval en biomassa voor energieopwekking in Nederland

Energy Technology Data Exchange (ETDEWEB)

Weterings, R.A.P.M.; Koppejan, J. [TNO Milieu, Energie- en Processinnovatie TNO-MEP, Apeldoorn (Netherlands); Bergsma, G.C. [Centrum voor Energiebesparing en schone technologie CE, Delft (Netherlands); Meeusen-van Onna, M.J.G. [Landbouw Economisch Instituut LEI, Den Haag (Netherlands)

1999-12-01

The Netherlands agency for energy and the environment (Novem) commissioned a consortium to carry out the ABC (Dutch abbreviation for Waste and Biomass Conversion) project in three separate studies: (A) a scenario study of the availability of biomass and waste for energy generation in the Netherlands; (B) a 'three-level assessment' of biomass availability on national, European and global levels; and (C) a scenario study of the feasibility / profitability of energy crops in the Netherlands. The results of the ABC project are published in two separate reports. This present report gives the results of the combined scenario study of availability (A) and the three-level assessment (B). The results of the energy crops study (C) are presented elsewhere. The goal of the present project is to gain insight into the current availability of biomass and waste flows for energy generation, and of the driving forces and constraints that can affect their availability up to the year 2020. First, it is examined whether the availability of biomass and waste is or could become problematic. This is an important aspect for market parties that want to invest in energy from biomass and biomass. Second, it is examined what additional policy measures the Dutch government would need to take to achieve the set policy goal of savings of fossil fuels. The combined scenario study of waste availability (in the Netherlands) and biomass availability (in the Netherlands, the European Union, and worldwide) for energy generation started off with a Definition Phase. In this phase, the project's framework and key issues were formulated and relevant sources of information were outlined. On the basis of these sources, a Quick Scan was carried out to map the existing information as well as any gaps in knowledge and uncertainties about the availability of biomass and waste. In the subsequent In-depth Phase the results of the Quick Scan were submitted to a number of national experts for comment

Process and apparatus for conversion of biomass

NARCIS (Netherlands)

Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

2006-01-01

The invention is directed to a process for the conversion of biomass, in particular lignocellulose-containing biomass into a product that may be further processes in a fermentation step. The invention is further directed to apparatus suitable for carrying out such processes. According to the

Summaries of studies carried out in the NKS/BOK-2 project. Technical report[Radiological and environmental consequences

Energy Technology Data Exchange (ETDEWEB)

Palsson, S E [Icelandic Radiation Protection Inst., Reykjavik (Iceland)

2002-12-01

Summaries of studies carried out in the NKSBOK-2 project, Radiological and Environmental Consequences. The structure of the project as such is described in NKS-64, Radiological and Environmental Consequences - Final Report of the Nordic Nuclear Safety Research Project BOK-2. That report also includes compilations based on the summaries presented in this report. The project was carried out 1998-2001 with participants from all the Nordic countries. Representatives from the Baltic States were also invited to some of the meetings and seminars. The project consisted of work on terrestrial and marine radioecology and had a broad scope in order to enable participation of research groups with various fields of interest. The topics included improving assessment of old and recent fallout, use of radionuclides as tracers in Nordic marine areas, improving assessment of internal doses and use of mass spectrometry in radioecology. This report is a compilation of summaries from each research group, 32 papers in all, and gives references to papers published in scientific journals. Some of the studies have been described previously, at least to some degree, in NKS-70, Proceedings of the 8{sup th} Nordic Seminar on Radioecology, 25-28 February 2001, Rovaniemi, Finland. (au)

48 CFR 1452.237-71 - Utilization of Woody Biomass.

Science.gov (United States)

2010-10-01

... Biomass. 1452.237-71 Section 1452.237-71 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... Utilization of Woody Biomass. As prescribed in § 1437.7202, insert the following clause: Utilization of Woody Biomass (MAY 2005) (a) The contractor may remove and utilize woody biomass, if: (1) Project work is...

Plant Biomass Leaching for Nutrient Recovery in Closed Loop Systems Project

Science.gov (United States)

Zeitlin, Nancy P.; Wheeler, Raymond (Compiler); Lunn, Griffin

2015-01-01

Plants will be important for food and O2 production during long term human habitation in space. Recycling of nutrients (e.g., from waste materials) could reduce the resupply costs of fertilizers for growing these plants. Work at NASA's Kennedy Space Center has shown that ion exchange resins can extract fertilizer (plant essential nutrients) from human waste water, after which the residual brine could be treated with electrodialysis to recover more water and produce high value chemicals (e.g., acids and bases). In habitats with significant plant production, inedible biomass becomes a major source of solid waste. To "close the loop" we also need to recover useful nutrients and fertilizer from inedible biomass. We are investigating different approaches to retrieve nutrients from inedible plant biomass, including physical leaching with water, processing the biomass in bioreactors, changing the pH of leaching processing, and/or conducting multiple leaches of biomass residues.

Bioenergy Research Programme. Yearbook 1994. Utilization of bioenergy and biomass conversion

International Nuclear Information System (INIS)

Alakangas, E.

1995-01-01

BIOENERGIA Research Programme is one of energy technology programmes of the Finnish Ministry of Trade and Industry (in 1995 TEKES, Technology Development Center). The aim of Bioenergy Research Programme is to increase the use of economically profitable and environmentally sound bioenergy by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels and new equipment and methods for production, handling and using of biofuels. The funding for 1994 was nearly 50 million FIM and project numbered 60. The research area of biomass conversion consisted of 8 projects in 1994, and the research area of bioenergy utilization of 13 projects. The results of these projects carried out in 1994 are presented in this publication. The aim of the biomass conversion research is to produce more bio-oils and electric power as well at wood processing industry as at power plants. The conversion research was pointed at refining of the waste liquors of pulping industry and the extracts of them into fuel oil and liquid engine fuels, on production of wood oil via flash pyrolysis, and on combustion tests. Other conversion studies dealt with production of fuel-grade ethanol. For utilization of agrobiomass in various forms of energy, a system study is introduced where special attention is how to use rapeseed oil unprocessed in heating boilers and diesel engines. Possibilities to produce agrofibre in investigated at a laboratory study

Wood Pellet-Fired Biomass Boiler Project at the Ketchikan Federal Building

Energy Technology Data Exchange (ETDEWEB)

Tomberlin, Gregg [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-06-01

Biomass boiler systems have existed for many years, but the technology has advanced in recent decades and can now provide automated and efficient operation for a relatively modest investment. Key advances in system monitoring and control allow for lower operating costs, since the control systems run all aspects of the boiler, including feed, load reduction and even tube cleaning. These advances have made such systems economical on a small scale in situations where inexpensive fuels like natural gas are not available. This creates an opportunity for building operators in remote, cold-climate locations to reduce the use of expensive fuels for heating buildings. GSA Region 10 installed the system at the federal building in Ketchikan, Alaska and submitted the project to the Green Proving Ground (GPG) program. GSA's GPG program contracted with the National Renewable Energy Laboratory (NREL) to assess the installation and the technology. The system serves as a demonstration to assess actual system efficiencies, as well as operating characteristics and financial benefits. In addition to installation and operational issues, the project team/researchers examined other issues, including fuel transportation costs, building energy savings, and overall economics.

Establishing biomass heating in the UK: phase 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The Biomass Heat Working Group, first set up in 1995, was taken on by British BioGen in 1996. Over the summer of 1996 British BioGen, supported by DTI, worked with the group to produce 'A Strategy to Develop the UK Market for Biomass Heating Installations'. In the spring of 1997 British BioGen agreed a two-year programme with ETSU (for the DTI) to 'Establish Biomass Heating in the UK'. The DTI's New and Renewable Energy Programme has supported this two-year programme which aims to bring together industry stakeholders and assist in the development of a significant biomass heat market in the UK. Overall we believe the project has been successful in its aim to increase the volume of biomass heating enquiries and enable greater use of the industry 'knowledge base'. Throughout the duration of the project a number of new biomass heating systems have been installed, including Shenstone Lodge School, Boughton Pumping Station and Elvendon Priory. In addition, an efficient system of information exchange has been established for customers and industry. British BioGen believe that the benefits of this system will be a crucial factor in achieving bioenergy industry targets of 2MWt for domestic heating, 2MWt for industrial and commercial heating and 2MWt for CHP by the end of 2001. The remainder of this summary offers highlights of the activities undertaken within the project, outlines the conclusions of the project and makes brief recommendations for further actions to assist the further deployment of biomass heating in the UK. (author)

High Pressure Biomass Gasification

Energy Technology Data Exchange (ETDEWEB)

Agrawal, Pradeep K [Georgia Tech Research Corporation, Atlanta, GA (United States)

2016-07-29

According to the Billion Ton Report, the U.S. has a large supply of biomass available that can supplement fossil fuels for producing chemicals and transportation fuels. Agricultural waste, forest residue, and energy crops offer potential benefits: renewable feedstock, zero to low CO₂ emissions depending on the specific source, and domestic supply availability. Biomass can be converted into chemicals and fuels using one of several approaches: (i) biological platform converts corn into ethanol by using depolymerization of cellulose to form sugars followed by fermentation, (ii) low-temperature pyrolysis to obtain bio-oils which must be treated to reduce oxygen content via HDO hydrodeoxygenation), and (iii) high temperature pyrolysis to produce syngas (CO + H₂). This last approach consists of producing syngas using the thermal platform which can be used to produce a variety of chemicals and fuels. The goal of this project was to develop an improved understanding of the gasification of biomass at high pressure conditions and how various gasification parameters might affect the gasification behavior. Since most downstream applications of synags conversion (e.g., alcohol synthesis, Fischer-Tropsch synthesis etc) involve utilizing high pressure catalytic processes, there is an interest in carrying out the biomass gasification at high pressure which can potentially reduce the gasifier size and subsequent downstream cleaning processes. It is traditionally accepted that high pressure should increase the gasification rates (kinetic effect). There is also precedence from coal gasification literature from the 1970s that high pressure gasification would be a beneficial route to consider. Traditional approach of using thermogravimetric analyzer (TGA) or high-pressure themogravimetric analyzer (PTGA) worked well in understanding the gasification kinetics of coal gasification which was useful in designing high pressure coal gasification processes. However

A study of palm biomass processing strategy in Sarawak

Science.gov (United States)

Lee, S. J. Y.; Ng, W. P. Q.; Law, K. H.

2017-06-01

In the past decades, palm industry is booming due to its profitable nature. An environmental concern regarding on the palm industry is the enormous amount of waste produced from palm industry. The waste produced or palm biomass is one significant renewable energy source and raw material for value-added products like fiber mats, activated carbon, dried fiber, bio-fertilizer and et cetera in Malaysia. There is a need to establish the palm biomass industry for the recovery of palm biomass for efficient utilization and waste reduction. The development of the industry is strongly depending on the two reasons, the availability and supply consistency of palm biomass as well as the availability of palm biomass processing facilities. In Malaysia, the development of palm biomass industry is lagging due to the lack of mature commercial technology and difficult logistic planning as a result of scattered locality of palm oil mill, where palm biomass is generated. Two main studies have been carried out in this research work: i) industrial study of the feasibility of decentralized and centralized palm biomass processing in Sarawak and ii) development of a systematic and optimized palm biomass processing planning for the development of palm biomass industry in Sarawak, Malaysia. Mathematical optimization technique is used in this work to model the above case scenario for biomass processing to achieve maximum economic potential and resource feasibility. An industrial study of palm biomass processing strategy in Sarawak has been carried out to evaluate the optimality of centralized processing and decentralize processing of the local biomass industry. An optimal biomass processing strategy is achieved.

Pyramiding genes and alleles for improving energy cane biomass yield

Energy Technology Data Exchange (ETDEWEB)

Ming, Ray [University of Illinois at Urbana-Champaign; Nagai, Chifumi [Hawaii Agriculture Research Center; Yu, Qingyi [Texas A & M AgriLife Research

2018-03-23

The overall goal of this project is to identify genes and gene interaction networks contributed to the extreme segregants with 30 folds biomass yield difference in sugarcane F2 populations. Towards achieving this goal, yield trials of 108 F2 extreme segregants from S. officinarum LA Purple and S. robustum MOL5829 (LM population) were carried out in two locations in three years. A yield trial of the second F2 population from S. officinarum LA Purple and S. spontaneum US56-14-4 (LU population) was installed in the summer of 2014 and the first set of yield component data was collected. For genotyping, transcriptomes from leaves and stalks of 70 extreme segregants of the LM F2 population and 119 individuals of the LU F2 populations were sequenced. The genomes of 91 F1 individuals from the LM populations are being sequenced to construct ultra-high density genetic maps for each of the two parents for both assisting the LA Purple genome assembling and for testing a hypothesis of female restitution. The genomes of 110 F2 individuals from single F1 in the LU population, a different set from the 119 F2 individuals used for transcriptome sequencing, are being sequenced for mapping genes and QTLs affecting biomass yield and for testing a hypothesis of female restitution. Gene expression analysis between extreme segregants of high and low biomass yield showed up-regulation of cellulose synthase, cellulose, and xylan synthase in high biomass yield segregants among 3,274 genes differentially expressed between the two extremes. Our transcriptome results revealed not only the increment of cell wall biosynthesis pathway is essential, but the rapid turnover of certain cell wall polymers as well as carbohydrate partitioning are also important for recycling and energy conservation during rapid cell growth in high biomass sugarcane. Seventeen differentially expressed genes in auxin, one in ethylene and one in gibberellin related signaling and biosynthesis pathways were identified, which

Biomass District Heat System for Interior Rural Alaska Villages

Energy Technology Data Exchange (ETDEWEB)

Wall, William A.; Parker, Charles R.

2014-09-01

Alaska Village Initiatives (AVI) from the outset of the project had a goal of developing an integrated village approach to biomass in Rural Alaskan villages. A successful biomass project had to be ecologically, socially/culturally and economically viable and sustainable. Although many agencies were supportive of biomass programs in villages none had the capacity to deal effectively with developing all of the tools necessary to build a complete integrated program. AVI had a sharp learning curve as well. By the end of the project with all the completed tasks, AVI developed the tools and understanding to connect all of the dots of an integrated village based program. These included initially developing a feasibility model that created the capacity to optimize a biomass system in a village. AVI intent was to develop all aspects or components of a fully integrated biomass program for a village. This meant understand the forest resource and developing a sustainable harvest system that included the “right sized” harvest equipment for the scale of the project. Developing a training program for harvesting and managing the forest for regeneration. Making sure the type, quality, and delivery system matched the needs of the type of boiler or boilers to be installed. AVI intended for each biomass program to be of the scale that would create jobs and a sustainable business.

Impact of different national biomass policies on investment costs of biomass district heating plants. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-01

The BIO-COST project - co-ordinated by E.V.A. - was funded by the European Commission's THERMIE Type B Programme. The objective of BIO-COST was to analyse the impact of national biomass policies on the investment costs of biomass district heating (DH) plants. The European comparison should help identifying measures to reduce investment costs for biomass DH plants and/or components down to a 'best practice' level. The investigation is based on the comparison of 20 biomass DH plants by country, with Denmark and Sweden having mainly high energy taxes as driver, while Austria and France rely mainly on subsidy systems. The results of BIO-COST show, that governmental policies can have a big impact especially on grid and buildings costs, effecting of course the overall costs of the plant enormously. Emission standards have their effects especially on the costs for technical equipment, however, this fact was not reflected in the BIO-COST data. The results do not show a clear advantage of either the energy tax approach or the subsidy approach: The French subsidy approach leads to fairly low cost levels compared to the Danish tax approach, while the Swedish tax approach seems to yield the lowest cost level. On the other hand the Austrian subsidy approach seems to intercrease investment costs. In principle both the tax as the subsidy approach can lead to the same effect: a project is calculated in such a way, that it just meets economic breakeven. This is typically the case when the project is not carried out by a private enterprise but by an operator aiming at enhanced public welfare (e.g. co-operative, municipality). In this case a subsidy model might yield more possibilities to encourage an economically efficient development, than a tax. Instead of giving subsidies as a fixed percentage of investments they could be adjusted to the actual needs of the project as proven by a standardised calculation. Of course this can create the incentive to expect higher

Commercial demonstration of atmospheric medium BTU fuel gas production from biomass without oxygen the Burlington, Vermont Project

Energy Technology Data Exchange (ETDEWEB)

Rohrer, J.W. [Zurn/NEPCO, South Portland, MA (United States); Paisley, M. [Battelle Laboratories, Columbus, OH (United States)

1995-12-31

The first U.S. demonstration of a gas turbine operating on fuel gas produced by the thermal gasification of biomass occurred at Battelle Columbus Labs (BCL) during 1994 using their high throughput indirect medium Btu gasification Process Research Unit (PRU). Zurn/NEPCO was retained to build a commercial scale gas plant utilizing this technology. This plant will have a throughput rating of 8 to 12 dry tons per hour. During a subsequent phase of the Burlington project, this fuel gas will be utilized in a commercial scale gas turbine. It is felt that this process holds unique promise for economically converting a wide variety of biomass feedstocks efficiently into both a medium Btu (500 Btu/scf) gas turbine and IC engine quality fuel gas that can be burned in engines without modification, derating or efficiency loss. Others are currently demonstrating sub-commercial scale thermal biomass gasification processes for turbine gas, utilizing both atmospheric and pressurized air and oxygen-blown fluid bed processes. While some of these approaches hold merit for coal, there is significant question as to whether they will prove economically viable in biomass facilities which are typically scale limited by fuel availability and transportation logistics below 60 MW. Atmospheric air-blown technologies suffer from large sensible heat loss, high gas volume and cleaning cost, huge gas compressor power consumption and engine deratings. Pressurized units and/or oxygen-blown gas plants are extremely expensive for plant scales below 250 MW. The FERCO/BCL process shows great promise for overcoming the above limitations by utilizing an extremely high throughout circulation fluid bed (CFB) gasifier, in which biomass is fully devolitalized with hot sand from a CFB char combustor. The fuel gas can be cooled and cleaned by a conventional scrubbing system. Fuel gas compressor power consumption is reduced 3 to 4 fold verses low Btu biomass gas.

Biomass resources in California

Energy Technology Data Exchange (ETDEWEB)

Tiangco, V.M.; Sethi, P.S. [California Energy Commission, Sacramento, CA (United States)

1993-12-31

The biomass resources in California which have potential for energy conversion were assessed and characterized through the project funded by the California Energy Commission and the US Department of Energy`s Western Regional Biomass Energy Program (WRBEP). The results indicate that there is an abundance of biomass resources as yet untouched by the industry due to technical, economic, and environmental problems, and other barriers. These biomass resources include residues from field and seed crops, fruit and nut crops, vegetable crops, and nursery crops; food processing wastes; forest slash; energy crops; lumber mill waste; urban wood waste; urban yard waste; livestock manure; and chaparral. The estimated total potential of these biomass resource is approximately 47 million bone dry tons (BDT), which is equivalent to 780 billion MJ (740 trillion Btu). About 7 million BDT (132 billion MJ or 124 trillion Btu) of biomass residue was used for generating electricity by 66 direct combustion facilities with gross capacity of about 800 MW. This tonnage accounts for only about 15% of the total biomass resource potential identified in this study. The barriers interfering with the biomass utilization both in the on-site harvesting, collection, storage, handling, transportation, and conversion to energy are identified. The question whether these barriers present significant impact to biomass {open_quotes}availability{close_quotes} and {open_quotes}sustainability{close_quotes} remains to be answered.

Public beliefs that may affect biomass development

International Nuclear Information System (INIS)

Draper, H.M.

1993-01-01

The Tennessee River chip mill controversy involves the expansion of the pulp and paper industry rather than the biomass energy industry; however, the concerns expressed by environmentalists are likely to be the same for biomass projects that propose use of privately-owned land. It may be incorrect to assume that private landowners will have more flexibility in forest management techniques than public agencies. In fact, when faced with a potentially large new demand source for wood, environmentalists will try to stop the project while pushing for stringent regulation of harvesting. This paper describes and analyzes beliefs about forest management (related to biomass energy) taken from the 1,200 letters and 200 public hearing statements received by TVA on the chip mill environmental impact statement. The chip mill controversy suggests that there is a potential for strong coalitions to form to stop new biomass demand sources. As much as possible, the biomass industry will need to anticipate and address land management issues. New concepts such as landscape ecology and ecosystem management should be considered. Even so, increased use of non-dedicated biomass resources will require more public acceptance of the concept that ecosystems and their biomass resources can tolerate increased levels of management

Great Lakes Regional Biomass Energy Program

International Nuclear Information System (INIS)

Kuzel, F.

1993-01-01

The Great Lakes Regional Biomass Energy Program (GLRBEP) was initiated September, 1983, with a grant from the Office of Energy Efficiency and Renewable Energy of the US Department of Energy (DOE). The program provides resources to public and private organizations in the Great Lakes region to increase the utilization and production of biomass fuels. The objectives of the GLRBEP are to: (1) improve the capabilities and effectiveness of biomass energy programs in the state energy offices; (2) assess the availability of biomass resources for energy in light of other competing needs and uses; (3) encourage private sector investments in biomass energy technologies; (4) transfer the results of government-sponsored biomass research and development to the private sector; (5) eliminate or reduce barriers to private sector use of biomass fuels and technology; (6) prevent or substantially mitigate adverse environmental impacts of biomass energy use. The Program Director is responsible for the day-to-day activities of the GLRBEP and for implementing program mandates. A 40 member Technical Advisory Committee (TAC) sets priorities and recommends projects. The governor of each state in the region appoints a member to the Steering Council, which acts on recommendations of the TAC and sets basic program guidelines. The GLRBEP is divided into three separate operational elements. The State Grants component provides funds and direction to the seven state energy offices in the region to increase their capabilities in biomass energy. State-specific activities and interagency programs are emphasized. The Subcontractor component involves the issuance of solicitations to undertake projects that address regional needs, identified by the Technical Advisory Committee. The Technology Transfer component includes the development of nontechnical biomass energy publications and reports by Council staff and contractors, and the dissemination of information at conferences, workshops and other events

Electrifying biomass

International Nuclear Information System (INIS)

Kusnierczyk, D.

2005-01-01

British Columbia's (BC) energy plan was outlined in this PowerPoint presentation. BC Hydro is the third largest electric utility in Canada with a generating capacity of 11,000 MW, 90 per cent of which is hydro generation. Various independent power project (IPP) biomass technologies were outlined, including details of biogas, wood residue and municipal solid waste facilities. An outline of BC Hydro's overall supply mix was presented, along with details of the IPP supply mix. It was suggested that the cancellation of the Duke Point power project has driven growth in the renewable energy sector. A chart of potential energy contribution by resource type was presented, as well as unit energy cost ranges. Resources included small and large hydro; demand side management; resource smart natural gas; natural gas; coal; wind; geothermal; biomass; wave; and tidal. The acquisition process was reviewed. Details of calls for tenders were presented, and issues concerning bidder responsibility and self-selection were examined. It was observed that wood residue presents a firm source of electricity that is generally local, and has support from the public. In addition, permits for wood residue energy conversion are readily available. However, size limitations, fuel risks, and issues concerning site control may prove to be significant challenges. It was concluded that the success of biomass energy development will depend on adequate access and competitive pricing. tabs., figs

First biomass conference of the Americas: Energy, environment, agriculture, and industry

International Nuclear Information System (INIS)

1993-01-01

This conference was designed to provide a national and international forum to support the development of a viable biomass industry. Although papers on research activities and technologies under development that address industry problems comprised part of this conference, an effort was made to focus on scale-up and demonstration projects, technology transfer to end users, and commercial applications of biomass and wastes. The conference was divided into these major subject areas: Resource Base, Power Production, Transportation Fuels, Chemicals and Products, Environmental Issues, Commercializing Biomass Projects, Biomass Energy System Studies, and Biomass in Latin America. The papers in this third volume deal with Environmental Issues, Biomass Energy System Studies, and Biomass in Latin America. Concerning Environmental Issues, the following topics are emphasized: Global Climate Change, Biomass Utilization, Biofuel Test Procedures, and Commercialization of Biomass Products. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database

Biomass - Overview of Swiss Research Programme 2003; Biomasse

Energy Technology Data Exchange (ETDEWEB)

Binggeli, D.; Guggisberg, B.

2003-07-01

This overview for the Swiss Federal Office of Energy (SFOE) discusses the results obtained in 2003 in various research projects worked on in Switzerland on the subject of biomass. In the biomass combustion area, subjects discussed include system optimisation for automatic firing, combustion particles, low-particle pellet furnaces, design and optimisation of wood-fired storage ovens, efficiency of filtering techniques and methane generation from wood. Also, an accredited testing centre for wood furnaces is mentioned and measurements made on an installation are presented. As far as the fermentation of biogenic wastes is concerned, biogas production from dairy-product wastes is described. Other projects discussed include a study on eco-balances of energy products, certification and marketing of biogas, evaluation of membranes, a measurement campaign for solar sludge-drying, the operation of a percolator installation for the treatment of bio-wastes, the effects of compost on the environment and the fermentation of coffee wastes. Also, statistics on biogas production in 2002 is looked at. Finally, a preliminary study on biofuels is presented.

Product Characterization for Entrained Flow Coal/Biomass Co-Gasification

Energy Technology Data Exchange (ETDEWEB)

Maghzi, Shawn; Subramanian, Ramanathan; Rizeq, George; Singh, Surinder; McDermott, John; Eiteneer, Boris; Ladd, David; Vazquez, Arturo; Anderson, Denise; Bates, Noel

2011-09-30

The U.S. Department of Energy‘s National Energy Technology Laboratory (DOE NETL) is exploring affordable technologies and processes to convert domestic coal and biomass resources to high-quality liquid hydrocarbon fuels. This interest is primarily motivated by the need to increase energy security and reduce greenhouse gas emissions in the United States. Gasification technologies represent clean, flexible and efficient conversion pathways to utilize coal and biomass resources. Substantial experience and knowledge had been developed worldwide on gasification of either coal or biomass. However, reliable data on effects of blending various biomass fuels with coal during gasification process and resulting syngas composition are lacking. In this project, GE Global Research performed a complete characterization of the gas, liquid and solid products that result from the co-gasification of coal/biomass mixtures. This work was performed using a bench-scale gasifier (BSG) and a pilot-scale entrained flow gasifier (EFG). This project focused on comprehensive characterization of the products from gasifying coal/biomass mixtures in a high-temperature, high-pressure entrained flow gasifier. Results from this project provide guidance on appropriate gas clean-up systems and optimization of operating parameters needed to develop and commercialize gasification technologies. GE‘s bench-scale test facility provided the bulk of high-fidelity quantitative data under temperature, heating rate, and residence time conditions closely matching those of commercial oxygen-blown entrained flow gasifiers. Energy and Environmental Research Center (EERC) pilot-scale test facility provided focused high temperature and pressure tests at entrained flow gasifier conditions. Accurate matching of syngas time-temperature history during cooling ensured that complex species interactions including homogeneous and heterogeneous processes such as particle nucleation, coagulation, surface condensation, and

Product Characterization for Entrained Flow Coal/Biomass Co-Gasification

Energy Technology Data Exchange (ETDEWEB)

Maghzi, Shawn [General Electric Global Research, Niskayuna, NY (United States); Subramanian, Ramanathan [General Electric Global Research, Niskayuna, NY (United States); Rizeq, George [General Electric Global Research, Niskayuna, NY (United States); Singh, Surinder [General Electric Global Research, Niskayuna, NY (United States); McDermott, John [General Electric Global Research, Niskayuna, NY (United States); Eiteneer, Boris [General Electric Global Research, Niskayuna, NY (United States); Ladd, David [General Electric Global Research, Niskayuna, NY (United States); Vazquez, Arturo [General Electric Global Research, Niskayuna, NY (United States); Anderson, Denise [General Electric Global Research, Niskayuna, NY (United States); Bates, Noel [General Electric Global Research, Niskayuna, NY (United States)

2011-12-11

The U.S. Department of Energy's National Energy Technology Laboratory (DOE NETL) is exploring affordable technologies and processes to convert domestic coal and biomass resources to high-quality liquid hydrocarbon fuels. This interest is primarily motivated by the need to increase energy security and reduce greenhouse gas emissions in the United States. Gasification technologies represent clean, flexible and efficient conversion pathways to utilize coal and biomass resources. Substantial experience and knowledge had been developed worldwide on gasification of either coal or biomass. However, reliable data on effects of blending various biomass fuels with coal during gasification process and resulting syngas composition are lacking. In this project, GE Global Research performed a complete characterization of the gas, liquid and solid products that result from the co-gasification of coal/biomass mixtures. This work was performed using a bench-scale gasifier (BSG) and a pilot-scale entrained flow gasifier (EFG). This project focused on comprehensive characterization of the products from gasifying coal/biomass mixtures in a high-temperature, high-pressure entrained flow gasifier. Results from this project provide guidance on appropriate gas clean-up systems and optimization of operating parameters needed to develop and commercialize gasification technologies. GE's bench-scale test facility provided the bulk of high-fidelity quantitative data under temperature, heating rate, and residence time conditions closely matching those of commercial oxygen-blown entrained flow gasifiers. Energy and Environmental Research Center (EERC) pilot-scale test facility provided focused high temperature and pressure tests at entrained flow gasifier conditions. Accurate matching of syngas time-temperature history during cooling ensured that complex species interactions including homogeneous and heterogeneous processes such as particle nucleation, coagulation, surface condensation

ADVANCED BIOMASS REBURNING FOR HIGH EFFICIENCY NOx CONTROL AND BIOMASS REBURNING - MODELING/ENGINEERING STUDIES JOINT FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Vladimir M. Zamansky; Mark S. Sheldon; Vitali V. Lissianski; Peter M. Maly; David K. Moyeda; Antonio Marquez; W. Randall Seeker

2000-10-01

This report presents results of studies under a Phase II SBIR program funded by the U. S. Department of Agriculture, and a closely coordinated project sponsored by the DOE National Energy Technology Laboratory (NETL, formerly FETC). The overall Phase II objective of the SBIR project is to experimentally optimize the biomass reburning technologies and conduct engineering design studies needed for process demonstration at full scale. The DOE project addresses supporting issues for the process design including modeling activities, economic studies of biomass handling, and experimental evaluation of slagging and fouling. The performance of biomass has been examined in a 300 kW (1 x 10{sup 6} Btu/hr) Boiler Simulator Facility under different experimental conditions. Fuels under investigation include furniture waste, willow wood and walnut shells. Tests showed that furniture pellets and walnut shells provided similar NO{sub x} control as that of natural gas in basic reburning at low heat inputs. Maximum NO{sub x} reduction achieved with walnut shell and furniture pellets was 65% and 58% respectively. Willow wood provided a maximum NO{sub x} reduction of 50% and was no better than natural gas at any condition tested. The efficiency of biomass increases when N-agent is injected into reburning and/or burnout zones, or along with OFA (Advanced Reburning). Co-injection of Na{sub 2}CO{sub 3} with N-agent further increases efficiency of NO{sub x} reduction. Maximum NO{sub x} reduction achieved with furniture pellets and willow wood in Advanced Reburning was 83% and 78% respectively. All combustion experiments of the Phase II project have been completed. All objectives of the experimental tasks were successfully met. The kinetic model of biomass reburning has been developed. Model agrees with experimental data for a wide range of initial conditions and thus correctly represents main features of the reburning process. Modeling suggests that the most important factors that provide

The study of different methods of bio-liquids production from wood biomass and from biomass/polyolefine mixtures

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B.N. [Institute of Chemistry and Chemical Technology, Siberian Branch, Russian Academy of Sciences, 660049 Krasnoyarsk, K. Marx str., 42 (Russian Federation); Siberian Federal University, Svobodny, 79, 660041 Krasnoyarsk (Russian Federation); Sharypov, V.I.; Kuznetsova, S.A.; Taraban' ko, V.E.; Ivanchenko, N.M. [Institute of Chemistry and Chemical Technology, Siberian Branch, Russian Academy of Sciences, 660049 Krasnoyarsk, K. Marx str., 42 (Russian Federation)

2009-08-15

The different methods of wood biomass thermal liquefaction at atmospheric and elevated pressures were investigated in order to select the more effective one. Wood biomass liquefaction by melted formate/alkali mixtures and with the use of metallic iron/Na{sub 2}CO{sub 3} system is carried out at low pressures. But these methods give only moderate yield of bio-liquids. The highest yield of bio-liquid was obtained in the process of biomass dissolvation in methanol media in the presence of Zn-Cr-Fe catalyst at 20 MPa. Co-pyrolysis and co-hydropyrolysis of biomass/polyolefine mixtures makes it possible to obtain the rather high yield of bio-liquid at the moderate pressures (3 MPa). (author)

EnerGEO biomass pilot

International Nuclear Information System (INIS)

Tum, M.; Guenther, K.P.; McCallum, I.; Balkovic, J.; Khabarov, N.; Kindermann, G.; Leduc, S.; Biberacher, M.

2013-01-01

In the framework of the EU FP7 project EnerGEO (Earth Observations for Monitoring and Assessment of the Environmental Impact of Energy Use) sustainable energy potentials for forest and agricultural areas were estimated by applying three different model approaches. Firstly, the Biosphere Energy Transfer Hydrology (BETHY/DLR) model was applied to assess agricultural and forest biomass increases on a regional scale with the extension to grassland. Secondly, the EPIC (Environmental Policy Integrated Climate) - a cropping systems simulation model - was used to estimate grain yields on a global scale and thirdly the Global Forest Model (G4M) was used to estimate global woody biomass harvests and stock. The general objective of the biomass pilot is to implement the observational capacity for using biomass as an important current and future energy resource. The scope of this work was to generate biomass energy potentials for locations on the globe and to validate these data. Therefore, the biomass pilot was focused to use historical and actual remote sensing data as input data for the models. For validation purposes, forest biomass maps for 1987 and 2002 for Germany (Bundeswaldinventur (BWI-2)) and 2001 and 2008 for Austria (Austrian Forest Inventory (AFI)) were prepared as reference. (orig.)

EnerGEO biomass pilot

Energy Technology Data Exchange (ETDEWEB)

Tum, M.; Guenther, K.P. [German Aerospace Center (DLR), Wessling (Germany). German Remote Sensing Data Center (DFD); McCallum, I.; Balkovic, J.; Khabarov, N.; Kindermann, G.; Leduc, S. [International Institute for Applied Systems Analysis (IIASA), Laxenburg (Austria); Biberacher, M. [Research Studios Austria AG (RSA), Salzburg (Austria)

2013-07-01

In the framework of the EU FP7 project EnerGEO (Earth Observations for Monitoring and Assessment of the Environmental Impact of Energy Use) sustainable energy potentials for forest and agricultural areas were estimated by applying three different model approaches. Firstly, the Biosphere Energy Transfer Hydrology (BETHY/DLR) model was applied to assess agricultural and forest biomass increases on a regional scale with the extension to grassland. Secondly, the EPIC (Environmental Policy Integrated Climate) - a cropping systems simulation model - was used to estimate grain yields on a global scale and thirdly the Global Forest Model (G4M) was used to estimate global woody biomass harvests and stock. The general objective of the biomass pilot is to implement the observational capacity for using biomass as an important current and future energy resource. The scope of this work was to generate biomass energy potentials for locations on the globe and to validate these data. Therefore, the biomass pilot was focused to use historical and actual remote sensing data as input data for the models. For validation purposes, forest biomass maps for 1987 and 2002 for Germany (Bundeswaldinventur (BWI-2)) and 2001 and 2008 for Austria (Austrian Forest Inventory (AFI)) were prepared as reference. (orig.)

Biomass is beginning to threaten the wood-processors

International Nuclear Information System (INIS)

Beer, G.; Sobinkovic, B.

2004-01-01

In this issue an exploitation of biomass in Slovak Republic is analysed. Some new projects of constructing of the stoke-holds for biomass processing are published. The grants for biomass are ascending the prices of wood raw material, which is thus becoming less accessible for the wood-processors. An excessive wood export threatens the domestic processors

Retrofit options to enable biomass firing at Irish peat plants: Background report 4.2 for the EU Joule 2+ project: Energy from biomass: An assessment of two promising systems for energy production

International Nuclear Information System (INIS)

Van den Broek, R.; Faaij, A.; Blaney, G.

1995-05-01

An overview is given of the most promising options for retrofitting existing Irish peat plants to accept biomass fuel. It is expected that with low investment costs the existing peat stations can be adapted to enable them to fire biomass. It will also be possible to co-fire peat and biomass, this option will become a way of using biomass in power generation with relatively low risk, both on the field of initial investments and supply security. The objectives of this report are: assessing the different technical options for retrofitting the plants to enable biomass firing; provide investment costs, efficiencies, emissions and expected lifetimes for the different retrofit options. The results from this study are used in the final integration phase of the EU-Joule project 'Energy from biomass'. Chapter 2 deals with methodological considerations which have been made in estimation of the investment costs. In chapter 3 the present situation is described. Both peat harvesting and power plant operation of both sod and milled peat plants are explained. Also some past experiences with wood chips firing in Irish peat stations are discussed. Chapter 4 gives a general view on retrofitting peat plants to enable biomass firing. Some starting points like biomass fuel feeding and emission standards that have to be met are highlighted. The rationale behind four main choices are given. Finally, a technical description is presented of the two boiler adaptations that will be considered among the different retrofit options, namely conversion of milled peat units into bubbling fluidized bed and into a whole tree energy unit. Six retrofit options are described in more detail in chapter 5. Information is given on the present status of the plants, the technical considerations of the retrofit, expected performance and an estimation of a range in which the investment costs can be expected. 4 figs., 10 tabs., 5 appendices

Closed Loop Short Rotation Woody Biomass Energy Crops

Energy Technology Data Exchange (ETDEWEB)

Brower, Michael [CRC Development, LLC, Oakland, CA (United States)

2012-09-30

CRC Development LLC is pursuing commercialization of shrub willow crops to evaluate and confirm estimates of yield, harvesting, transportation and renewable energy conversion costs and to provide a diverse resource in its supply portfolio.The goal of Closed Loop Short Rotation Woody Biomass Energy Crops is supply expansion in Central New York to facilitate the commercialization of willow biomass crops as part of the mix of woody biomass feedstocks for bioenergy and bioproducts. CRC Development LLC established the first commercial willow biomass plantation acreage in North America was established on the Tug Hill in the spring of 2006 and expanded in 2007. This was the first 230- acres toward the goal of 10,000 regional acres. This project replaces some 2007-drought damaged acreage and installs a total of 630-acre new planting acres in order to demonstrate to regional agricultural producers and rural land-owners the economic vitality of closed loop short rotation woody biomass energy crops when deployed commercially in order to motivate new grower entry into the market-place. The willow biomass will directly help stabilize the fuel supply for the Lyonsdale Biomass facility, which produces 19 MWe of power and exports 15,000 pph of process steam to Burrows Paper. This project will also provide feedstock to The Biorefinery in New York for the manufacture of renewable, CO2-neutral liquid transportation fuels, chemicals and polymers. This project helps end dependency on imported fossil fuels, adds to region economic and environmental vitality and contributes to national security through improved energy independence.

Diesel power plants based on biomass gasification; Biomassan ja turpeen kaasutukseen perustuvien dieselvoimalaitosten toteutettavuustutkimus

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E.; Staahlberg, P.; Solantausta, Y.; Wilen, C.

1995-12-31

Different power production systems have been developed for biomass feedstocks. However, only few of these systems can meet the following three requirements: (a) suitability to small scale electricity production (< 5-10 MWe), (b) reliable operation with realistically available biomass feedstocks, and (c) potential for economical competitiveness. The fluidized-bed boilers have been successfully operated with wood waste and peat down to outputs of the order of 5 MWe and the investment costs have been successfully lowered to a reasonable level. However, this concept is most suitable for combined heat and electricity production and smaller plant sizes are not considered feasible. One of the most promising alternative for this commercially proven technology is the diesel power plant based on gasification. This concept has a potential for higher power to heat ratios in cogeneration or higher efficiency in separate electricity production. The objectives of this project were (a) to evaluate the technical and economical feasibility of diesel power plants based on biomass gasification and (b) to study the effects of operating conditions (temperature, bed material and air staging) on the performance of a circulating fluidized-bed gasifier. The experimental part of the project was carried out on a new PDU-scale Circulating Fluidized-Bed Gasification test facility of VTT. Wood residues were used as the feedstocks and the experiments were mainly focused on tar formation and gasifier performance. The results will be compared to earlier VTT data obtained for bubbling-bed reactors. The techno-economic feasibility studies are carried out using existing process modelling tools of VTT and the gasification based diesel plants will be compared to conventional fluidized-bed boilers

Diesel power plants based on biomass gasification; Biomassan ja turpeen kaasutukseen perustuvien dieselvoimalaitosten toteutettavuustutkimus

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E; Staahlberg, P; Solantausta, Y; Wilen, C

1996-12-31

Different power production systems have been developed for biomass feedstocks. However, only few of these systems can meet the following three requirements: (a) suitability to small scale electricity production (< 5-10 MWe), (b) reliable operation with realistically available biomass feedstocks, and (c) potential for economical competitiveness. The fluidized-bed boilers have been successfully operated with wood waste and peat down to outputs of the order of 5 MWe and the investment costs have been successfully lowered to a reasonable level. However, this concept is most suitable for combined heat and electricity production and smaller plant sizes are not considered feasible. One of the most promising alternative for this commercially proven technology is the diesel power plant based on gasification. This concept has a potential for higher power to heat ratios in cogeneration or higher efficiency in separate electricity production. The objectives of this project were (a) to evaluate the technical and economical feasibility of diesel power plants based on biomass gasification and (b) to study the effects of operating conditions (temperature, bed material and air staging) on the performance of a circulating fluidized-bed gasifier. The experimental part of the project was carried out on a new PDU-scale Circulating Fluidized-Bed Gasification test facility of VTT. Wood residues were used as the feedstocks and the experiments were mainly focused on tar formation and gasifier performance. The results will be compared to earlier VTT data obtained for bubbling-bed reactors. The techno-economic feasibility studies are carried out using existing process modelling tools of VTT and the gasification based diesel plants will be compared to conventional fluidized-bed boilers

Fundamental mechanisms for conversion of volatiles in biomass and waste combustion. Final report

Energy Technology Data Exchange (ETDEWEB)

Glarborg, P.; Hindiyarti, L.; Marshall, P.; Livbjerg, H.; Dagaut, P.; Jensen, Anker; Frandsen, Flemming

2007-03-15

This project deals with the volatile oxidation chemistry in biomass and waste fired systems, emphasizing reactions important for pollutants emissions (NO{sub x}, SO{sub 2}, HCl, aerosols). The project aims to extend existing models and databases with a number of chemical subsystems that are presently not well understood, but are particularly important in connection with combustion of biomass and waste. The project is divided into 3 tasks. Task 1: Conversion of chlorine, sulfur and alkali gas phase components in combustion of biomass. Task 2: Formation mechanisms for NO{sub x} in the freeboard of grate combustion of biomass. Task 3: Oxidation mechanisms for oxygenated hydrocarbons in the volatiles from pyrolysis of biomass. (au)

Biomass: towards more co-generation than gasification? Interview with Jean-Christophe Pouet; Figures for the heat fund; biomass in the Parisian heat network; gasification still at the promise stage; Engie bets on bio-methane of 2. generation; a new bidding for biomass co-generation

International Nuclear Information System (INIS)

Petitot, Pauline; De Santis, Audrey; Mary, Olivier; Signoret, Stephane

2016-01-01

After some brief presentations of some highlights in the biomass sector in France, Ukraine, UK and Brazil, a set of articles proposes an overview of recent developments and perspectives for the biomass-based energy and heat production in France. It presents and comments some emerging projects based on biomass gasification as technologies have evolved for a higher economic profitability. It discusses the action of the Heat Fund (Fonds chaleur) which supports investors in a context constrained by the hard competition with fossil energies, notably with gas as discussed in an interview with a member of the ADEME. Some tables and graphs give data about biomass installations supported by the Heat fund, about subsidies awarded by the ADEME, about the production of the various heat sources. An article comments the operation of a biomass-based plant near Paris which supplies the Parisian heat network. A project of methane production from dry biomass from local resources by Engie near Lyons (methane of second generation). The last article comments a new bidding process for co-generation projects which can be an opportunity for new projects, and not only big ones

Experiments and modelling on biomass transport inside upflow ...

African Journals Online (AJOL)

This paper describes the experimental and theoretical activities developed to study the biomass transport phenomena occurring in upflow anaerobic reactors influencing the biomass washout. Particularly, the experimental investigations have been carried out on a full-scale ABR and on a pilot UASB intermittently fed with ...

Biomass Thermochemical Conversion Program. 1983 Annual report

Energy Technology Data Exchange (ETDEWEB)

Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

1984-08-01

Highlights of progress achieved in the program of thermochemical conversion of biomass into clean fuels during 1983 are summarized. Gasification research projects include: production of a medium-Btu gas without using purified oxygen at Battelle-Columbus Laboratories; high pressure (up to 500 psia) steam-oxygen gasification of biomass in a fluidized bed reactor at IGT; producing synthesis gas via catalytic gasification at PNL; indirect reactor heating methods at the Univ. of Missouri-Rolla and Texas Tech Univ.; improving the reliability, performance, and acceptability of small air-blown gasifiers at Univ. of Florida-Gainesville, Rocky Creek Farm Gasogens, and Cal Recovery Systems. Liquefaction projects include: determination of individual sequential pyrolysis mechanisms at SERI; research at SERI on a unique entrained, ablative fast pyrolysis reactor for supplying the heat fluxes required for fast pyrolysis; work at BNL on rapid pyrolysis of biomass in an atmosphere of methane to increase the yields of olefin and BTX products; research at the Georgia Inst. of Tech. on an entrained rapid pyrolysis reactor to produce higher yields of pyrolysis oil; research on an advanced concept to liquefy very concentrated biomass slurries in an integrated extruder/static mixer reactor at the Univ. of Arizona; and research at PNL on the characterization and upgrading of direct liquefaction oils including research to lower oxygen content and viscosity of the product. Combustion projects include: research on a directly fired wood combustor/gas turbine system at Aerospace Research Corp.; adaptation of Stirling engine external combustion systems to biomass fuels at United Stirling, Inc.; and theoretical modeling and experimental verification of biomass combustion behavior at JPL to increase biomass combustion efficiency and examine the effects of additives on combustion rates. 26 figures, 1 table.

Electricity production by advanced biomass power systems

Energy Technology Data Exchange (ETDEWEB)

Solantausta, Y [VTT Energy, Espoo (Finland). Energy Production Technologies; Bridgwater, T [Aston Univ. Birmingham (United Kingdom); Beckman, D [Zeton Inc., Burlington, Ontario (Canada)

1996-11-01

This report gives the results of the Pyrolysis Collaborative Project organized by the International Energy Agency (IEA) under Biomass Agreement. The participating countries or organizations were Canada, European Community (EC), Finland, United States of America, and the United Kingdom. The overall objective of the project was to establish baseline assessments for the performance and economics of power production from biomass. Information concerning the performance of biomass-fuelled power plants based on gasification is rather limited, and even less data is available of on pyrolysis based power applications. In order to gain further insight into the potential for these technologies, this study undertook the following tasks: (1) Prepare process models to evaluate the cost and performance of new advanced biomass power production concepts, (2) Assess the technical and economic uncertainties of different biomass power concepts, (3) Compare the concepts in small scale and in medium scale production (5 - 50 MW{sub e}) to conventional alternatives. Processes considered for this assessment were biomass power production technologies based on gasification and pyrolysis. Direct combustion technologies were employed as a reference for comparison to the processes assessed in this study. Wood was used a feedstock, since the most data was available for wood conversion

Transport and supply logistics of biomass fuels: Vol. 1. Supply chain options for biomass fuels

Energy Technology Data Exchange (ETDEWEB)

Allen, J; Browne, M; Palmer, H; Hunter, A; Boyd, J

1996-10-01

The study which forms part of a wider project funded by the Department of Trade and Industry, looks at the feasibility of generating electricity from biomass-fuelled power stations. Emphasis is placed on supply availabilty and transport consideration for biomass fuels such as wood wastes from forestry, short rotation coppice products, straw, miscanthus (an energy crop) and farm animal slurries. The study details the elements of the supply chain for each fuel from harvesting to delivery at the power station. The delivered cost of each fuel, the environmental impact of the biomass fuel supply and other relevant non-technical issues are addressed. (UK)

ADVANCED BIOMASS REBURNING FOR HIGH EFFICIENCY NOx CONTROL AND BIOMASS REBURNING - MODELING/ENGINEERING STUDIES JOINT FINAL REPORT; FINAL

International Nuclear Information System (INIS)

Vladimir M Zamansky; Mark S. Sheldon; Vitali V. Lissianski; Peter M. Maly; David K. Moyeda; Antonio Marquez; W. Randall Seeker

2000-01-01

This report presents results of studies under a Phase II SBIR program funded by the U. S. Department of Agriculture, and a closely coordinated project sponsored by the DOE National Energy Technology Laboratory (NETL, formerly FETC). The overall Phase II objective of the SBIR project is to experimentally optimize the biomass reburning technologies and conduct engineering design studies needed for process demonstration at full scale. The DOE project addresses supporting issues for the process design including modeling activities, economic studies of biomass handling, and experimental evaluation of slagging and fouling. The performance of biomass has been examined in a 300 kW (1 x 10(sup 6) Btu/hr) Boiler Simulator Facility under different experimental conditions. Fuels under investigation include furniture waste, willow wood and walnut shells. Tests showed that furniture pellets and walnut shells provided similar NO(sub x) control as that of natural gas in basic reburning at low heat inputs. Maximum NO(sub x) reduction achieved with walnut shell and furniture pellets was 65% and 58% respectively. Willow wood provided a maximum NO(sub x) reduction of 50% and was no better than natural gas at any condition tested. The efficiency of biomass increases when N-agent is injected into reburning and/or burnout zones, or along with OFA (Advanced Reburning). Co-injection of Na(sub 2)CO(sub 3) with N-agent further increases efficiency of NO(sub x) reduction. Maximum NO(sub x) reduction achieved with furniture pellets and willow wood in Advanced Reburning was 83% and 78% respectively. All combustion experiments of the Phase II project have been completed. All objectives of the experimental tasks were successfully met. The kinetic model of biomass reburning has been developed. Model agrees with experimental data for a wide range of initial conditions and thus correctly represents main features of the reburning process. Modeling suggests that the most important factors that provide

Experiences of the BIOMAS-CUBA Project. Energy alternatives from biomass in Cuban rural areas

International Nuclear Information System (INIS)

Suárez, J.; Martín, G. J.; Cepero, L.; Funes-Monzote, F.; Blanco, D.; Machado, R.; Sotolongo, J. A.; Rodríguez, E.; Savran, Valentina; Rivero, J. L.; Martín, C.; García, A.

2011-01-01

This paper provides experiences of the international project BIOMAS-CUBA in the implementation of energy supply alternatives from biomass in rural areas, which are compatible to food security and environmental sustainability. These experiences are comprised between 2009 and 2011, within the agroenergetic farm concept, and are related to research and technological innovation processes associated to: the morphological, productive and chemical evaluation of germplasm of non-edible oil plants with potential to produce biodiesel, ethanol and other products; the planting and agricultural management of associations of Jatropha curcas and 21 food crops; the cleaning and oil extraction of Jatropha seeds; the physical-chemical characterization of such oil; the production of biodiesel and its co-products; the biogas production from excreta and bioproducts and biofertilizers, with the effluents of biodigesters; the gasification of ligneous biomass to generate electricity; the characterization and classification of integrated food and energy production systems. Likewise, the socioeconomic and environmental studies allowed appreciating adequate economic-financial feasibility, remarkable increases in food production, the formation of human capital and the improvement of the people's quality of life, a positive environmental impact and a substitution of energy porters and conventional fertilizers. (author)

Development of low cost systems for co-utilisation of biomass in large power plant. Mid term review report

Energy Technology Data Exchange (ETDEWEB)

Livingston, W.R.

2003-07-01

Interest in the cofiring of biomass materials with coal in large coal-fired power stations in the UK has increased significantly in recent years in response to the potential additional income from Renewables Obligation Certificates (ROCs). It is anticipated that most coal-fired power stations in the UK will have the capability to cofire biomass materials by the end of 2003. This mid-term review report examines the various stages in the route to fully commercial operation of biomass cofiring at coal-fired power stations, the availability of suitable biomass materials in the UK and the technical options for cofiring. The factors affecting the economics of biomass cofiring in large coal-fired boilers are discussed including the delivered price of biofuels, the future value of ROCs, the development costs of cofiring projects, the 25% ceiling on cofiring imposed by the Renewables Obligation Order 2002 and the use of preblending. An overview of the current status of cofiring in the UK is presented, which includes a summary of the results of trials already carried out by operators of coal-fired power stations and a discussion of the future prospects for biomass cofiring in the UK.

Sustainability of biomass utilisation in changing operational environment - SUBICHOE

Energy Technology Data Exchange (ETDEWEB)

Soimakallio, S.; Hongisto, M.; Koponen, K.; Sokka, L. (VTT Technical Research Centre of Finland, Espoo (Finland)), Email: sampo.soimakallio@vtt.fi; Antikainen, R.; Manninen, K. (Finnish Environment Inst. SYKE, Helsinki (Finland)); Thun, R.; Sinkko, T. (MTT Agrifood Research Finland, Jokioinen (Finland)); Pasanen, K. (Finnish Forest Research Inst., Joensuu (Finland))

2010-10-15

Sustaibability is a multi-faceted and challenging target, but at the same time a crucial issue to assess when setting policies and targets for the future. The main objective of the SUBICHOE project is to assist in strategic decision- making of public administration and companies, as regards the most sustainable use of biomass, by taking into account the changing operational environment. In the project the sustainability of biofuels and the criteria, in particular those set by the EC, for ensuring that set requirements can and will be fulfilled are being assessed from short and long term perspectives. The project is carried out jointly by VTT Technical Research Centre of Finland, Finnish Environment Institute SYKE, MTT Agrifood Research Finland, Finnish Forest Research Institute (Metla) and The Government Institute for Economic Research (VATT). The project started in June 2009 and it is scheduled to be finalised in June 2011. The work plan of the project is divided into four Work Packages. In this article, a summary of a critical view on the requirements and challenges related to the implementation of the RES Directive is also provided based on the main findings of the WP1. (orig.)

Bioenergy research programme. Yearbook 1996. Peat and field biomass; Bioenergian tutkimusohjelma. Vuosikirja 1996. Turpeen ja peltobiomassojen tuotantotekniikka

Energy Technology Data Exchange (ETDEWEB)

Nikku, P [ed.

1997-12-01

The aim of the programme is to increase the use of economically profitable and environmentally sound bioenergy by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels, new equipment and methods for production, handling and utilisation of biofuels. The total funding for 1996 was 27.3 million FIM and the number of projects 63. The number of projects concerning peat production was 7 and that of field biomass projects 4. Results of the projects carried out in 1996 are presented in this publication. The development target in the research area of peat production is to improve the competitiveness of peat by reducing the production costs by 20 % (by 5-6 FIM/MWh) from the level of 1992, and to reduce the environmental impacts. The target of the research area of peat production is possible to achieve if the sub-targets are achieved. The production costs are reduced by 5 % if the width of the production field is increased from 20 m to 60 m, by 8 % if the degree of utilisation of solar energy is increased from 30 % to 40 %, by 6.5 % if the value of peat remaining on the cutover field is reduced from 3 000 MWh to 1 500 MWh, by 3 % if light and fireproof machines are developed, and by 3 % if combined peat and wood harvesting is applied. The production costs will be reduced by 24 % if the different sub-targets are achieved. In this programme no common target for the field biomass projects was set. Field biomass projects are mainly funded by the Finnish Ministry of Agriculture and Forestry. Most of the research projects were completed in 1996. (orig.)

Sun Grant Initiative Regional Biomass Feedstock Partnership Competitive Grants Program

Energy Technology Data Exchange (ETDEWEB)

Owens, Vance [South Dakota State Univ., Brookings, SD (United States). North Central Regional Sun Grant Center

2016-12-30

The Sun Grant Initiative partnered with the US Department of Energy (DOE) in 2008 to create the Regional Biomass Feedstock Partnership Competitive Grants Program. The overall goal of this project was to utilize congressionally directed funds to leverage the North Central Regional Sun Grant’s Competitive Grant program at South Dakota State University (SDSU) to address key issues and research gaps related to development of the bioeconomy. Specific objectives of this program were to: 1. Identify research projects through a Regional Competitive Grants program that were relevant to the sustainable production, harvest, transport, delivery, and processing/conversion of cost-competitive, domestically grown biomass. 2. Build local expertise and capacity at the North Central Regional Sun Grant Center at SDSU through an internal selection of key bioenergy research projects. To achieve these, three nationwide Request for Applications (RFA) were developed: one each in 2008, 2009, and 2010. Internal, capacity building projects at SDSU were also selected during each one of these RFAs. In 2013 and 2015, two additional Proof of Concept RFAs were developed for internal SDSU projects. Priority areas for each RFA were 1) Biomass feedstock logistics including biomass harvesting, handling, transportation, storage, and densification; 2) Sustainable biomass feedstock production systems including biomass crop development, production, and life-cycle analysis; 3) Biomass production systems that optimize biomass feedstock yield and economic return across a diverse landscape while minimizing negative effects on the environment and food/feed production; and 4) Promotion of knowledge-based economic development in science and technology and to advance commercialization of inventions that meet the mission of the Sun Grant Initiative. A total of 33 projects were selected for funding through this program. Final reports for each of these diverse projects are included in this summary report

PRODUCTION OF NEW BIOMASS/WASTE-CONTAINING SOLID FUELS

Energy Technology Data Exchange (ETDEWEB)

David J. Akers; Glenn A. Shirey; Zalman Zitron; Charles Q. Maney

2001-04-20

CQ Inc. and its team members (ALSTOM Power Inc., Bliss Industries, McFadden Machine Company, and industry advisors from coal-burning utilities, equipment manufacturers, and the pellet fuels industry) addressed the objectives of the Department of Energy and industry to produce economical, new solid fuels from coal, biomass, and waste materials that reduce emissions from coal-fired boilers. This project builds on the team's commercial experience in composite fuels for energy production. The electric utility industry is interested in the use of biomass and wastes as fuel to reduce both emissions and fuel costs. In addition to these benefits, utilities also recognize the business advantage of consuming the waste byproducts of customers both to retain customers and to improve the public image of the industry. Unfortunately, biomass and waste byproducts can be troublesome fuels because of low bulk density, high moisture content, variable composition, handling and feeding problems, and inadequate information about combustion and emissions characteristics. Current methods of co-firing biomass and wastes either use a separate fuel receiving, storage, and boiler feed system, or mass burn the biomass by simply mixing it with coal on the storage pile. For biomass or biomass-containing composite fuels to be extensively used in the U.S., especially in the steam market, a lower cost method of producing these fuels must be developed that includes both moisture reduction and pelletization or agglomeration for necessary fuel density and ease of handling. Further, this method of fuel production must be applicable to a variety of combinations of biomass, wastes, and coal; economically competitive with current fuels; and provide environmental benefits compared with coal. Notable accomplishments from the work performed in Phase I of this project include the development of three standard fuel formulations from mixtures of coal fines, biomass, and waste materials that can be used in

A Novel Slurry-Based Biomass Reforming Process Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Emerson, Sean C. [United Technologies Research Center, East Hartford, CT (United States); Davis, Timothy D. [United Technologies Research Center, East Hartford, CT (United States); Peles, A. [United Technologies Research Center, East Hartford, CT (United States); She, Ying [United Technologies Research Center, East Hartford, CT (United States); Sheffel, Joshua [United Technologies Research Center, East Hartford, CT (United States); Willigan, Rhonda R. [United Technologies Research Center, East Hartford, CT (United States); Vanderspurt, Thomas H. [United Technologies Research Center, East Hartford, CT (United States); Zhu, Tianli [United Technologies Research Center, East Hartford, CT (United States)

2011-09-30

This project was focused on developing a catalytic means of producing H2 from raw, ground biomass, such as fast growing poplar trees, willow trees, or switch grass. The use of a renewable, biomass feedstock with minimal processing can enable a carbon neutral means of producing H2 in that the carbon dioxide produced from the process can be used in the environment to produce additional biomass. For economically viable production of H2, the biomass is hydrolyzed and then reformed without any additional purification steps. Any unreacted biomass and other byproduct streams are burned to provide process energy. Thus, the development of a catalyst that can operate in the demanding corrosive environment and presence of potential poisons is vital to this approach. The concept for this project is shown in Figure 1. The initial feed is assumed to be a >5 wt% slurry of ground wood in dilute base, such as potassium carbonate (K2CO3). Base hydrolysis and reforming of the wood is carried out at high but sub-critical pressures and temperatures in the presence of a solid catalyst. A Pd alloy membrane allows the continuous removal of pure , while the retentate, including methane is used as fuel in the plant. The project showed that it is possible to economically produce H2 from woody biomass in a carbon neutral manner. Technoeconomic analyses using HYSYS and the DOE's H2A tool [1] were used to design a 2000 ton day-1 (dry basis) biomass to hydrogen plant with an efficiency of 46% to 56%, depending on the mode of operation and economic assumptions, exceeding the DOE 2012 target of 43%. The cost of producing the hydrogen from such a plant would be in the range of $1/kg H2 to $2/kg H2. By using raw biomass as a feedstock, the cost of producing hydrogen at large biomass consumption rates is more cost effective than steam reforming of hydrocarbons or biomass gasification and can achieve the overall cost goals of the DOE Fuel Cell Technologies Program. The complete conversion of wood

Allometric relationship and biomass expansion factors (BEFs) for above- and below-ground biomass prediction and stem volume estimation for ash (Fraxinus excelsior L.) and oak (Quercus robur L.)

Czech Academy of Sciences Publication Activity Database

Krejza, Jan; Světlík, J.; Bednář, P.

2017-01-01

Roč. 31, č. 4 (2017), s. 1303-1316 ISSN 0931-1890 R&D Projects: GA MŠk(CZ) LO1415 Institutional support: RVO:67179843 Keywords : floodplain forest * root biomass * leaf biomass * branch biomass * shoot biomass * Allometry * stem volume * biomass expansion factor Subject RIV: GK - Forestry OBOR OECD: Forestry Impact factor: 1.842, year: 2016

Pellets for Power: sustainable biomass import from Ukraine : public final report

NARCIS (Netherlands)

Elbersen, H.W.; Poppens, R.P.; Lesschen, J.P.; Sluis, van der T.; Galytska, M.; Kulyk, M.; Jamblinne, de P.; Kraisvitnii, P.; Rii, O.; Hoekstra, T.

2013-01-01

This project responds to the mismatch between on the one hand a growing demand for biomass on the Dutch and EU energy markets with a limited biomass potential and on the other hand large amounts of biomass and biomass potential currently underutilised in Ukraine. Ukraine itself is seen as a very

Mobility chains analysis of technologies for passenger cars and light duty vehicles fueled with biofuels : application of the Greet model to project the role of biomass in America's energy future (RBAEF) project.

Energy Technology Data Exchange (ETDEWEB)

Wu, M.; Wu, Y.; Wang, M; Energy Systems

2008-01-31

The Role of Biomass in America's Energy Future (RBAEF) is a multi-institution, multiple-sponsor research project. The primary focus of the project is to analyze and assess the potential of transportation fuels derived from cellulosic biomass in the years 2015 to 2030. For this project, researchers at Dartmouth College and Princeton University designed and simulated an advanced fermentation process to produce fuel ethanol/protein, a thermochemical process to produce Fischer-Tropsch diesel (FTD) and dimethyl ether (DME), and a combined heat and power plant to co-produce steam and electricity using the ASPEN Plus{trademark} model. With support from the U.S. Department of Energy (DOE), Argonne National Laboratory (ANL) conducted, for the RBAEF project, a mobility chains or well-to-wheels (WTW) analysis using the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model developed at ANL. The mobility chains analysis was intended to estimate the energy consumption and emissions associated with the use of different production biofuels in light-duty vehicle technologies.

Projecting demand and supply of forest biomass for heating in Norway

International Nuclear Information System (INIS)

Tromborg, Erik; Havskjold, Monica; Lislebo, Ole; Rorstad, Per Kristian

2011-01-01

This paper assesses the increase in demand and supply for forest biomass for heating in Norway in 2020. By then there is a political aim to double the national production of bioenergy from the level in 2008. The competitiveness of woody biomass in central and district heating is analyzed in a model selecting the least-cost heating technology and scale in municipalities given a set of constraints and under different fuels price scenarios. The supply of forest biomass from roundwood is estimated based on data of forest inventories combined with elasticities regarding price and standing volumes. The supply of biomass from harvesting residues is estimated in an engineering approach based on data from the national forest inventories and roundwood harvest. The results show how the production of bioenergy is affected by changes in energy prices and support schemes for bioenergy. One conclusion from the analyses is that the government target of 14 TWh more bioenergy by 2020 is not likely to be met by current technologies and policy incentives. The contribution of the analysis is the detailed presentation of the heat market potentials and technology choices combined with supply functions for both roundwood and harvesting residues. - Highlights: → This paper accesses the demand and supply for forest biomass for heating in Norway in 2020. → Market share for wood in central and new district heating is analyzed in a cost-minimizing model. → The supply of forest biomass includes wood chips from import, roundwood and harvesting residues. → The production of bioenergy is affected by changes in energy prices and support schemes. → The government target for bioenergy is not met by current technologies and policy incentives.

Northeast Regional Biomass Program: Mission, accomplishments, prospects, 1991

International Nuclear Information System (INIS)

1991-03-01

This 1991 Report contains an update on the mission, goals and accomplishments of the Northeast Regional Biomass Program (NRBP). It describes the activities conducted during the past two years and incorporates the information contained in the 1989 publication of the NRBP Five Year Report. It describes the biomass projects conducted by the individual states of the Northeast Region, and summarizes the results from the Program's technical studies. Publications from both the state and regional projects are listed as well. An appendix lists the biomass-fired electricity generating stations planned or in operation in the region. The NRBP began in 1983 by developing a five year plan to guide its work. Within that time frame, the NRBP undertook over 20 applied research and technology transfer projects, and supported and guided the work of its eleven member states. During and since that period, the NRBP has brought together public and private sector organizations to promote the use in the Northeast of biomass and municipal waste energy resources and technologies. The NRBP's long-range plan was updated in 1990. In light of the accomplishments of the NRBP and the remaining challenges, this Report considers directions for future efforts. The Northeast has abundant biomass resources and markets for their use as energy. Meeting this potential will contribute to reducing the atmospheric greenhouse effect and dependence on imported oil. 49 refs

Electric power generation using biomass gasification systems in nature in isolated communities of the Amazon region: project GASEIBRAS; Geracao de eletricidade utilizando sistemas de gaseificacao de biomassa in natura em comunidades isoladas da regiao amazonica: projeto GASEIBRAS

Energy Technology Data Exchange (ETDEWEB)

Coelho, Suani Teixeira; Velazquez, Silvia M. Stortini Goncalves; Santos, Sandra M. Apolinario dos; Lora, Beatriz Acquaro [Universidade de Sao Paulo (CENBIO/USP), SP (Brazil). Centro de Referencia Nacional em Biomassa], e-mails: suani@iee.usp.br, sgvelaz@iee.usp.br, sandra@iee.usp.br, blora@iee.usp.br

2006-07-01

This paper will present the pioneering project of electric energy generation from renewable sources 'GASEIBRAS - Nationalization of the Biomass Gasification Technology and Formation of Human Resources in the Amazon Region', recently approved by the National Advice of Scientific and Technological Development (CNPq) and for the Ministry of Mines and Energy (MME). The GASEIBRAS project intends to use the experience previously acquired in the project GASEIFAMAZ - Comparison between Existing Technologies of Biomass Gasification in Brazil and Exterior and Formation of Human Resources in the North Region, sponsored by FINEP/CTENERG, to develop and construct a 20 kWe biomass gasification system, with total national technology, easy to operate and to maintain, and fed with local available biomass residues. Apart from contributing for the development of the national technology, this project will provide the sustainable development of the isolated communities in the Amazon region. The ongoing development of this project will enable to consolidate the national biomass gasification technology for electricity generation. The implemented prototype will allow the response of this project in other regions of the country, due its tailor made characteristic to attend to small isolated communities, thus supplying decentralized energy from renewable sources, to Amazon region. (author)

Lessons learned from existing biomass power plants

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

2000-02-24

This report includes summary information on 20 biomass power plants, which represent some of the leaders in the industry. In each category an effort is made to identify plants that illustrate particular points. The project experiences described capture some important lessons learned that lead in the direction of an improved biomass power industry.

The gasification of biomass: A technological challenge. Biomassa vergassen: Een technologische uitdaging

Energy Technology Data Exchange (ETDEWEB)

Portegijs, J

1993-05-01

The gasification of specially for that purpose cultivated poplars and bamboo or other biomass is an attractive option for the production of electricity. An overview is given of projects and the techniques, by which this option can be realized. Examples of biomass gasification projects in Sweden and Finland are briefly discussed. Possibilities to implement small-scale biomass gasification in the Netherlands are outlined. 1 ill., 1 tab., 4 refs.

EERC Center for Biomass Utilization 2005

Energy Technology Data Exchange (ETDEWEB)

Zygarlicke, C J; Schmidt, D D; Olson, E S; Leroux, K M; Wocken, C A; Aulich, T A; WIlliams, K D

2008-07-28

Biomass utilization is one solution to our nation’s addiction to oil and fossil fuels. What is needed now is applied fundamental research that will cause economic technology development for the utilization of the diverse biomass resources in the United States. This Energy & Environmental Research Center (EERC) applied fundamental research project contributes to the development of economical biomass utilization for energy, transportation fuels, and marketable chemicals using biorefinery methods that include thermochemical and fermentation processes. The fundamental and basic applied research supports the broad scientific objectives of the U.S. Department of Energy (DOE) Biomass Program, especially in the area of developing alternative renewable biofuels, sustainable bioenergy, technologies that reduce greenhouse gas emissions, and environmental remediation. Its deliverables include 1) identifying and understanding environmental consequences of energy production from biomass, including the impacts on greenhouse gas production, carbon emission abatement, and utilization of waste biomass residues and 2) developing biology-based solutions that address DOE and national needs related to waste cleanup, hydrogen production from renewable biomass, biological and chemical processes for energy and fuel production, and environmental stewardship. This project serves the public purpose of encouraging good environmental stewardship by developing biomass-refining technologies that can dramatically increase domestic energy production to counter current trends of rising dependence upon petroleum imports. Decreasing the nation’s reliance on foreign oil and energy will enhance national security, the economy of rural communities, and future competitiveness. Although renewable energy has many forms, such as wind and solar, biomass is the only renewable energy source that can be governed through agricultural methods and that has an energy density that can realistically compete with

Production of methanol/DME from biomass

DEFF Research Database (Denmark)

Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Münster-Swendsen, Janus

In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier...... cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51...... gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic...

Energy Efficiency and Air Quality Repairs at Lyonsdale Biomass

Energy Technology Data Exchange (ETDEWEB)

Brower, Michael R; Morrison, James A; Spomer, Eric; Thimot, Carol A

2012-07-31

This project enabled Lyonsdale Biomass, LLC to effect analyses, repairs and upgrades for its biomass cogeneration facility located in Lewis County, New York and close by the Adirondack Park to reduce air emissions by improving combustion technique and through the overall reduction of biomass throughput by increasing the system's thermodynamic efficiency for its steam-electrical generating cycle. Project outcomes result in significant local, New York State, Northeast U.S. and national benefits including improved renewable energy operational surety, enhanced renewable energy efficiency and more freedom from foreign fossil fuel source dependence. Specifically, the reliability of the Lyonsdale Biomass 20MWe woody biomass combined-heat and power (CHP) was and is now directly enhanced. The New York State and Lewis County benefits are equally substantial since the facility sustains 26 full-time equivalency (FTE) jobs at the facility and as many as 125 FTE jobs in the biomass logistics supply chain. Additionally, the project sustains essential local and state payment in lieu of taxes revenues. This project helps meet several USDOE milestones and contributes directly to the following sustainability goals:  Climate: Reduces greenhouse gas emissions associated with bio-power production, conversion and use, in comparison to fossil fuels. Efficiency and Productivity: Enhances efficient use of renewable resources and maximizes conversion efficiency and productivity. Profitability: Lowers production costs. Rural Development: Enhances economic welfare and rural development through job creation and income generation. Standards: Develop standards and corresponding metrics for ensuring sustainable biopower production. Energy Diversification and Security: Reduces dependence on foreign oil and increases energy supply diversity. Net Energy Balance: Ensures positive net energy balance for all alternatives to fossil fuels.

Decommissioning of nuclear power stations in community countries carried out and projected

International Nuclear Information System (INIS)

Cregut, A.; Gregory, A.R.

1984-01-01

The decommissioning of large plants such as nuclear power stations merits an approach requiring the introduction of measures and procedures allowing them to be dealt with efficiently; this efficiency would imply concern for optimum economy of operations while respecting the safety and protection rules inherent in nuclear energy. Consequently, plant owners require: the tactical and policy elements to guide them in their decisions and choices; efficient tools, equipment and processes which meet their needs; information gained from experience of decommissioning already carried out which would provide them with a verified background knowledge when dealing with problems. Since decommissioning experience to date has not made it possible to draw up codes and guidelines, it is important to review the work carried out by Community countries in particular on the decommissioning of nuclear power plants. The following paper does not claim to be exhaustive or to make value judgements. Its aim is to list the nuclear power stations shut down in Community countries, to outline the decommissioning levels selected in each case and to underline some interesting aspects of the technical options. In conclusion it will review what appeared to be the difficulties common to the various projects. (author)

Sustainability of biomass utilisation in changing operational environment - SUBICHOE

Energy Technology Data Exchange (ETDEWEB)

Soimakallio, S. [VTT Technical Research Centre of Finland, Espoo (Finland)], email: sampo.soimakallio@vtt.fi

2012-07-01

The main objective of the project was to assist in strategic decision-making of public administration and companies, as regards the most sustainable use of biomass, by taking into account the changing operational environment. This project continued the work of the BIOVAIKU project by exploring in more details the most critical issues identified in sustainability assessment. These include the need to develop assessment methods and criteria in particular for land use and land-use change due to biomass cultivation and harvesting and indirect impacts due to resource competition.

Diesel power plants based on biomass gasification; Biomassan ja turpeen kaasutukseen perustuen dieselvoimalaitosten toteutettavuustutkimus

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E.; Staahlberg, P.; Solantausta, Y. [VTT Energy, Espoo (Finland)

1996-12-01

Different power production systems have been developed for biomass feedstocks. However, only few of these systems can meet the following three requirements: (1) suitability to small scale electricity production (<5-10 MWe), (2) reliable operation with realistically available biomass feedstocks, and (3) potential for economical competitiveness. The fluidized-bed boilers have been successfully operated with wood waste and peat down to outputs of the order of 5 MWe and the investment costs have been successfully lowered to a reasonable level. However, this concept is most suitable for combined heat and electricity production and smaller plant sizes are not considered feasible. One of the most promising alternative for this commercially proven technology is the diesel power plant based on gasification. This concept has a potential for higher power to heat ratios in cogeneration or higher efficiency in separate electricity production. The objectives of this project were (1) to evaluate the technical and economical feasibility of diesel power plants based on biomass gasification and (2) to study the effects of operating conditions (temperature, bed material and air staging) on the performance of a circulating fluidized-bed gasifier. The experimental part of the project was carried out on a new PDU-scale Circulating Fluidized-Bed Gasification test facility of VTT. Wood residues were used as the feedstocks and the experiments were mainly focused on tar formation and gasifier performance. The results will be compared to earlier VTT data obtained for bubbling-bed reactors. The techno-economic feasibility studies are carried out using existing process modelling tools of VTT and the gasification based diesel plants will be compared to conventional fluidized-bed boilers. The studies are scheduled to be completed in March 1996. (author)

District heating and combined heat and power generation from biomass

International Nuclear Information System (INIS)

Veski, Rein

1999-01-01

An Altener programme seminar District Heating and Combined Heat and Power Generation from Biomass. Minitraining seminar and study tours and also Business forum, Exhibition and Short company presentations were held in Tallinn on March 21-23, 1999. The Seminar was organised by the VTT Energy, the Estonian Bioenergy Association and the Estonian Heat and Power Association in co-operation with the AFB-net. The Agricultural and Forestry Biomass Network (AFB-net) is part of the ALTENER programme. The Network aims at promoting and stimulating the implementation and commercial utilisation of energy from biomass and waste, through the initiation of business opportunities. This includes national and international co-operation and the exchange of the personnel. The Seminar was attended by consulting companies, scientists, municipal authorities and representatives of co-ordinating bodies engaged in renewable energy management as well as DH and CHP plant managers, equipment manufacturers and local energy planners from Finland, Estonia, Latvia, Lithuania, Sweden, Denmark, Belgium, Slovenia and Slovak Republic. At the Seminar minitraining issues were dealt with: the current situation and future trends in biomass DH in the Baltic Sea countries, and biomass DH and CHP in Eastern and Central Europe, planning and construction of biomass-based DH plants, biomass fuel procurement and handling technology, combustion technology, DH networks, financing of biomass projects and evaluating of projects, and case projects in Eastern and Central European countries. The following were presented: boilers with a capacity of 100 kW or more, stoker burners, wood and straw handling equipment, wood fuel harvesters, choppers, pelletisers, district heating pipelines and networks. (author)

Life cycle assessment of biomass-to-energy systems in Ireland modelled with biomass supply chain optimisation based on greenhouse gas emission reduction

International Nuclear Information System (INIS)

Murphy, Fionnuala; Sosa, Amanda; McDonnell, Kevin; Devlin, Ger

2016-01-01

The energy sector is the major contributor to GHG (greenhouse gas emissions) in Ireland. Under EU Renewable energy targets, Ireland must achieve contributions of 40%, 12% and 10% from renewables to electricity, heat and transport respectively by 2020, in addition to a 20% reduction in GHG emissions. Life cycle assessment methodology was used to carry out a comprehensive, holistic evaluation of biomass-to-energy systems in 2020 based on indigenous biomass supply chains optimised to reduce production and transportation GHG emissions. Impact categories assessed include; global warming, acidification, eutrophication potentials, and energy demand. Two biomass energy conversion technologies are considered; co-firing with peat, and biomass CHP (combined heat and power) systems. Biomass is allocated to each plant according to a supply optimisation model which ensures minimal GHG emissions. The study shows that while CHP systems produce lower environmental impacts than co-firing systems in isolation, determining overall environmental impacts requires analysis of the reference energy systems which are displaced. In addition, if the aims of these systems are to increase renewable energy penetration in line with the renewable electricity and renewable heat targets, the optimal scenario may not be the one which achieves the greatest environmental impact reductions. - Highlights: • Life cycle assessment of biomass co-firing and CHP systems in Ireland is carried out. • GWP, acidification and eutrophication potentials, and energy demand are assessed. • Biomass supply is optimised based on minimising GHG emissions. • CHP systems cause lower environmental impacts than biomass co-firing with peat. • Displacing peat achieves higher GHG emission reductions than replacing fossil heat.

Biomass gasification for energy production

Energy Technology Data Exchange (ETDEWEB)

Lundberg, H.; Morris, M.; Rensfelt, E. [TPS Termiska Prosesser Ab, Nykoeping (Sweden)

1997-12-31

Biomass and waste are becoming increasingly interesting as fuels for efficient and environmentally sound power generation. Circulating fluidized bed (CFB) gasification for biomass and waste has been developed and applied to kilns both in the pulp and paper industry and the cement industry. A demonstration plant in Greve-in- Chianti, Italy includes two 15 MW{sub t}h RDF-fuelled CFB gasifiers of TPS design, the product gas from which is used in a cement kiln or in steam boiler for power generation. For CFB gasification of biomass and waste to reach a wider market, the product gas has to be cleaned effectively so that higher fuel to power efficiencies can be achieved by utilizing power cycles based on engines or gas turbines. TPS has developed both CFB gasification technology and effective secondary stage tar cracking technology. The integrated gasification - gas-cleaning technology is demonstrated today at pilot plant scale. To commercialise the technology, the TPS`s strategy is to first demonstrate the process for relatively clean fuels such as woody biomass and then extend the application to residues from waste recycling. Several demonstration projects are underway to commercialise TPS`s gasification and gas cleaning technology. In UK the ARBRE project developed by ARBRE Energy will construct a gasification plant at Eggborough, North Yorkshire, which will provide gas to a gas turbine and steam turbine generation system, producing 10 MW and exporting 8 Mw of electricity. It has been included in the 1993 tranche of the UK`s Non Fossil Fuel Obligation (NFFO) and has gained financial support from EC`s THERMIE programme as a targeted BIGCC project. (author)

Biomass gasification for energy production

Energy Technology Data Exchange (ETDEWEB)

Lundberg, H; Morris, M; Rensfelt, E [TPS Termiska Prosesser Ab, Nykoeping (Sweden)

1998-12-31

Biomass and waste are becoming increasingly interesting as fuels for efficient and environmentally sound power generation. Circulating fluidized bed (CFB) gasification for biomass and waste has been developed and applied to kilns both in the pulp and paper industry and the cement industry. A demonstration plant in Greve-in- Chianti, Italy includes two 15 MW{sub t}h RDF-fuelled CFB gasifiers of TPS design, the product gas from which is used in a cement kiln or in steam boiler for power generation. For CFB gasification of biomass and waste to reach a wider market, the product gas has to be cleaned effectively so that higher fuel to power efficiencies can be achieved by utilizing power cycles based on engines or gas turbines. TPS has developed both CFB gasification technology and effective secondary stage tar cracking technology. The integrated gasification - gas-cleaning technology is demonstrated today at pilot plant scale. To commercialise the technology, the TPS`s strategy is to first demonstrate the process for relatively clean fuels such as woody biomass and then extend the application to residues from waste recycling. Several demonstration projects are underway to commercialise TPS`s gasification and gas cleaning technology. In UK the ARBRE project developed by ARBRE Energy will construct a gasification plant at Eggborough, North Yorkshire, which will provide gas to a gas turbine and steam turbine generation system, producing 10 MW and exporting 8 Mw of electricity. It has been included in the 1993 tranche of the UK`s Non Fossil Fuel Obligation (NFFO) and has gained financial support from EC`s THERMIE programme as a targeted BIGCC project. (author)

Considerations in implementing integrated biomass energy systems in developing countries

International Nuclear Information System (INIS)

Perlack, R.D.; Ranney, J.W.

1993-01-01

Biomass energy is emerging as a real option for satisfying power needs in developing countries. Experience has shown improvements in GDP are directly linked to increased consumption of energy. Biomass energy can also be environmentally and developmentally beneficial where it will be both grown and used. Biomass production can offset deforestation, reduce soil erosion, increase rural employment, and stimulate development. Moreover, when biomass is grown renewably there is no net buildup of atmospheric carbon. Issues and barriers associated with implementing integrated biomass energy systems in developing countries are discussed. An integrated biomass energy system is dependent on sustainably grown and managed energy crops, supportive of rural development, and environmentally beneficial, adapted to local conditions; takes advantage of by- and co-products and uses conversion technologies that have been optimized for biomass. A preliminary evaluation of a biomass to electricity project relying on plantation grown feedstocks in Southwest China indicates that biomass could be grown and converted to electricity at costs lower than alternatives and yield an internal rate of return of about 15%. The IRR based on a social and environmental benefits are substantial and investment in the facility is well-justified. However, assessing biomass energy systems is exceedingly complex. Considerations are grouped into biomass production, biomass logistics and transport, and biomass conversion. Implementation requires considerations of energy and economics, institutional and social issues, and environmental issues. The conclusion that such a project would be viable in rural China is shadowed by many site-specific circumstances and highlights the need for systematic and integrated appraisal

Application of Molecular Sieves in Transformations of Biomass and Biomass- Derived Feedstocks

Czech Academy of Sciences Publication Activity Database

Kubička, D.; Kubičková, I.; Čejka, Jiří

2013-01-01

Roč. 55, č. 1 (2013), s. 1-78 ISSN 0161-4940 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : biomass * molecular sieves * zeolites Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 6.111, year: 2013

System applications CRC -Biomass + Coal; Aplicaciones Sistema CRC-Biomasa+Carbon

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

Main object of Phase I of the project is to analyse the technical-economic feasibility of the combined use of biomass and coal for power generation in the Spanish region of Andalusia, by means of new medium-size independent power plants or using biomass as supplementary fuel in existing large coal power plants, including: -Analysis and classification of biomass and coal resources in the region -Technical-economic study of conventional alternatives using the steam cycle -Analysis of efficiency improvement provided by advanced Rankine-cycle technologies, like the SMR cycle -Analysis of alternatives based on parallel combined cycles using gas turbines, including advanced solutions, like the EAPI and CRC-EAPI systems. -Description and evaluation of different biomass drying systems. -Description and evaluation of the three main biomass gasification systems currently under development: atmospheric direct, atmospheric indirect and pressurized. Main objects of Phase II of the project are to analyse a specific application of the EAPI system to a real cogeneration plant project and to analyse the application of the CRC2 system to a commercial supercritical power plant, including technical-economic study of both applications. (Author)

Researches concerning the use of mixed Hydrogen in the combustion of dense biomass

International Nuclear Information System (INIS)

Negreanu, Gabriel-Paul; Mihaescu, Lucian; Pisa, Ionel; Berbece, Viorel; Lazaroiu, Gheorghe

2014-01-01

The paper deals with theoretical basis and experimental tests of mixed hydrogen diffusion in the dense system of biomass. Research regarding hydrogen diffusion in the porous system of biomass is part of wider research focusing on using hydrogen as an active medium for solid biomass combustion. In parallel with hydrogen diffusion in solid biomass, tests regarding biomass combustion previously subjected to a hydrogen flux will be carried out. Keywords: biomass, hydrogen diffusion, combustion, experimental tests

Bioenergy research programme. Yearbook 1996. Utilization of bioenergy and biomass conversion; Bioenergian tutkimusohjelma. Vuosikirja 1996. Bioenergian kaeyttoe ja biomassan jalostus

Energy Technology Data Exchange (ETDEWEB)

Nikku, P [ed.

1997-12-01

The aim of the programme is to increase the use of economically profitable and environmentally sound bioenergy by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels, new equipment and methods for production, handling and utilisation of biofuels. The total funding for 1996 was 27.3 million FIM and the number of projects 63. The number of projects concerning bioenergy use was 10 and biomass conversion 6. Results of the projects carried out in 1996 are presented in this publication. The aim of the bioenergy use is to develop and demonstrate at least 3-4 new equipment or methods for handling and use of biofuels. The equipment and/or methods should provide economically competitive and environmentally sound energy production. The second aim is to demonstrate 2-3 large-scale biofuel end-use technologies. Each of these should have a potential of 0.2- 0.3 million toe/a till the year 2000. The aims have been achieved in the field of fuel handling technologies and small-scale combustion concepts, but large-scale demonstration projects before the year 2000 seems to be a very challenging aim. The aim of the biomass conversion is to produce basic information on biomass conversion, to evaluate the quality of products, their usability, environmental effects of use as well as the total economy of the production. The objective of biomass conversion is to develop 2-3 new methods, which could be demonstrated, for the production and utilisation of liquefied, gasified and other converted biofuels. The production target is 0.2-0.3 million toe/a by the year 2000 at a competitive price level. The studies focused on the development of flash pyrolysis technology for biomass, and on the study of storage stability of imported wood oils and of their suitability for use in oil-fired boilers and diesel power plants

BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

Energy Technology Data Exchange (ETDEWEB)

Bruce C. Folkedahl; Jay R. Gunderson; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

2002-09-01

The Energy & Environmental Research Center (EERC) has completed a project to examine fundamental issues that could limit the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC attempted to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low-volatile fuels with lower reactivities can experience problematic fouling when switched to higher-volatile and more reactive coal-biomass blends. Higher heat release rates at the grate can cause increased clinkering or slagging at the grate due to higher temperatures. Combustion and loss of volatile matter can start much earlier for biomass fuels compared to design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates, various chlorides, and phosphates. These species in combination with different flue gas temperatures, because of changes in fuel heating value, can adversely affect ash deposition behavior. The goal of this project was to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass--specifically wood and agricultural residuals--in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project were: (1) Modification of an existing pilot-scale combustion system to simulate a grate-fired system. (2) Verification testing of the simulator. (3) Laboratory-scale testing and fuel characterization to

Biomass energy conversion: conventional and advanced technologies

Energy Technology Data Exchange (ETDEWEB)

Young, B C; Hauserman, W B [Energy and Environmental Research Center, University of North Dakota, Grand Forks, ND (United States)

1995-12-01

Increasing interest in biomass energy conversion in recent years has focused attention on enhancing the efficiency of technologies converting biomass fuels into heat and power, their capital and operating costs and their environmental emissions. Conventional combustion systems, such as fixed-bed or grate units and entrainment units, deliver lower efficiencies (<25%) than modem coal-fired combustors (30-35%). The gasification of biomass will improve energy conversion efficiency and yield products useful for heat and power generation and chemical synthesis. Advanced biomass gasification technologies using pressurized fluidized-bed systems, including those incorporating hot-gas clean-up for feeding gas turbines or fuel cells, are being demonstrated. However, many biomass gasification processes are derivatives of coal gasification technologies and do not exploit the unique properties of biomass. This paper examines some existing and upcoming technologies for converting biomass into electric power or heat. Small-scale 1-30 MWe units are emphasized, but brief reference is made to larger and smaller systems, including those that bum coal-biomass mixtures and gasifiers that feed pilot-fuelled diesel engines. Promising advanced systems, such as a biomass integrated gasifier/gas turbine (BIG/GT) with combined-cycle operation and a biomass gasifier coupled to a fuel cell, giving cycle efficiencies approaching 50% are also described. These advanced gasifiers, typically fluid-bed designs, may be pressurized and can use a wide variety of biomass materials to generate electricity, process steam and chemical products such as methanol. Low-cost, disposable catalysts are becoming available for hot-gas clean-up (enhanced gas composition) for turbine and fuel cell systems. The advantages, limitations and relative costs of various biomass gasifier systems are briefly discussed. The paper identifies the best known biomass power projects and includes some information on proposed and

Biomass energy conversion: conventional and advanced technologies

International Nuclear Information System (INIS)

Young, B.C.; Hauserman, W.B.

1995-01-01

Increasing interest in biomass energy conversion in recent years has focused attention on enhancing the efficiency of technologies converting biomass fuels into heat and power, their capital and operating costs and their environmental emissions. Conventional combustion systems, such as fixed-bed or grate units and entrainment units, deliver lower efficiencies (<25%) than modem coal-fired combustors (30-35%). The gasification of biomass will improve energy conversion efficiency and yield products useful for heat and power generation and chemical synthesis. Advanced biomass gasification technologies using pressurized fluidized-bed systems, including those incorporating hot-gas clean-up for feeding gas turbines or fuel cells, are being demonstrated. However, many biomass gasification processes are derivatives of coal gasification technologies and do not exploit the unique properties of biomass. This paper examines some existing and upcoming technologies for converting biomass into electric power or heat. Small-scale 1-30 MWe units are emphasized, but brief reference is made to larger and smaller systems, including those that bum coal-biomass mixtures and gasifiers that feed pilot-fuelled diesel engines. Promising advanced systems, such as a biomass integrated gasifier/gas turbine (BIG/GT) with combined-cycle operation and a biomass gasifier coupled to a fuel cell, giving cycle efficiencies approaching 50% are also described. These advanced gasifiers, typically fluid-bed designs, may be pressurized and can use a wide variety of biomass materials to generate electricity, process steam and chemical products such as methanol. Low-cost, disposable catalysts are becoming available for hot-gas clean-up (enhanced gas composition) for turbine and fuel cell systems. The advantages, limitations and relative costs of various biomass gasifier systems are briefly discussed. The paper identifies the best known biomass power projects and includes some information on proposed and

Energy Opportunities from Lignocellulosic Biomass for a Biorefinery Case Study

Directory of Open Access Journals (Sweden)

Franco Cotana

2016-09-01

Full Text Available This work presents some energy considerations concerning a biorefinery case study that has been carried out by the CRB/CIRIAF of the University of Perugia. The biorefinery is the case study of the BIT3G project, a national funded research project, and it uses the lignocellulosic biomass that is available in the territory as input materials for biochemical purposes, such as cardoon and carthamus. The whole plant is composed of several sections: the cardoon and carthamus seed milling, the oil refinement facilities, and the production section of some high quality biochemicals, i.e., bio-oils and fatty acids. The main goal of the research is to demonstrate energy autonomy of the latter section of the biorefinery, while only recovering energy from the residues resulting from the collection of the biomass. To this aim, this work presents the quantification of the energy requirements to be supplied to the considered biorefinery section, the mass flow, and the energy and chemical characterization of the biomass. Afterwards, some sustainability strategies have been qualitatively investigated in order to identify the best one to be used in this case study; the combined heat and power (CHP technology. Two scenarios have been defined and presented: the first with 6 MWt thermal input and 1.2 MWe electrical power as an output and the second with 9 MWt thermal input and 1.8 MWe electrical power as an output. The first scenario showed that 11,000 tons of residual biomass could ensure the annual production of about 34,000 MWht, equal to about the 72% of the requirements, and about 9600 MWhe, equal to approximately 60% of the electricity demand. The second scenario showed that 18,000 tons of the residual biomass could ensure the total annual production of about 56,000 MWht, corresponding to more than 100% of the requirements, and about 14,400 MWhe, equal to approximately 90% of the electricity demand. In addition, the CO2 emissions from the energy valorization

Clean and efficient application of biomass for production of power and heat - Phase 3 in a long-term strategic research project

Energy Technology Data Exchange (ETDEWEB)

Frandsen, F.J.; Jensen, A.D.; Jensen, P.A.; Johnsson, J.E.; Dam-Johansen, K.

2002-06-01

This project contains activities on: Rheology of ashes from co-firing of coal and biomass; Investigation of ash and deposit formation in full-scale utility boilers; and Selective catalytic reduction: Deactivation under biomass combustion. A fly ash and deposit investigation was carried out as part of the SK Power Company test programme on co-firing of biomasses in a grate-fired boiler. The alternative biomasses (wood chips, olive stones and shea nuts) contain more K, S, and Cl, than wheat straw, and higher fly ash mass loading (mass of fly ash/volume of flue gas) was observed when co-firing alternative biomasses with wheat straw. Anyhow, no significant change in deposit structure when co-firing alkali-rich biomass was observed: KCl is glues residual ash particles together, independent of the feedstock mixture. Thus it can be concluded that co-firing of the actual biomasses in boilers designed for straw-firing, at the present shares is not problematic, from an ash formation and/or deposit build-up point-of-view. Anyhow the increase in ash mass loading in the flue gas, may cause increased build-up of particulate deposits in the convective pass of the boiler. Mature deposit samples from the Masnedoe and Ensted straw-fired boilers were investigated by SEM and EDX. Each deposit sample was classified into an inner, an intermediate, and an outer main layer. The outermost deposit layers at Masnedoe and Ensted looked chemically quite similar, even though they were of different colours. The intermediate layer at Ensted contained many Si- and Ca-rich particles glued together by melted KCI, while the intermediate deposit layers at Masnedoe were different. Since the straw fuels probably are similar, the differences observed in the deposit chemistry must be induced by the higher temperature of the Masnedoe deposit. An experimental method has been set up for viscosity determinations on ashes from co-firing with wheat straw. The method contains a pre-treatment of the ashes, where

Development of Solar Biomass Drying System

Directory of Open Access Journals (Sweden)

Atnaw Samson Mekbib

2017-01-01

Full Text Available The purpose of this paper focuses on the experimental pre-treatment of biomass in agricultural site using solar energy as power source and contribution of common use and efficiency solar dryer system for consumer. The main purpose of this design for solar cabinet dryer is to dry biomass via direct and indirect heating. Direct heating is the simplest method to dry biomass by exposing the biomass under direct sunlight. The solar cabinet dryer traps solar heat to increase the temperature of the drying chamber. The biomass absorbs the heat and transforms the moisture content within the biomass into water vapour and then leaves the chamber via the exhaust air outlet. This problem however can be solved by adopting indirect solar drying system. High and controllable temperatures can be achieved as a fan is used to move the air through the solar collector. This project has successfully created a solar cabinet dryer that combines both direct and indirect solar drying systems and functions to dry biomass as well as crops effectively and efficiently with minimal maintenance. Hence, it is indeed a substitution for conventional dryers which are affordable to local farmers.

Review and analysis of the 1980-1989 biomass thermochemical conversion program

Energy Technology Data Exchange (ETDEWEB)

Stevens, D.J.

1994-09-01

In the period between 1980 and 1989, the U.S. Department of Energy (DOE) sponsored research and development projects through its Biomass Thermochemical Conversion (BTC) Program. Thermochemical conversion technologies use elevated temperatures to convert biomass into more useful forms of energy such as fuel gases or transportation fuels. The BTC Program included a wide range of biomass conversion projects in the areas of gasification, pyrolysis, liquefaction, and combustion. This work formed the basis of the present DOE research and development efforts on advanced liquid fuel and power generation systems. At the beginning of Fiscal Year 1989, the management of the BTC Program was transferred from Pacific Northwest Laboratory (PNL) to National Renewable Energy Laboratory (NREL, formerly Solar Energy Research Institute). This document presents a summary of the research which was performed under the BTC Program during the 1981-1989 time frame. The document consists of an analysis of the research projects which were funded by the BTC Program and a bibliography of published documents. This work will help ensure that information from PNL`s BTC Program is available to those interested in biomass conversion technologies. The background of the BTC Program is discussed in the first chapter of this report. In addition, a brief summary of other related biomass research and development programs funded by the U.S. Department of Energy and others is presented with references where additional information can be found. The remaining chapters of the report present a detailed summary of the research projects which were funded by the BTC Program. The progress which was made on each project is summarized, the overall impact on biomass conversion is discussed, and selected references are provided.

Sustainable use of forest biomass for energy

International Nuclear Information System (INIS)

Stupak Moeller, Inge

2005-01-01

The substitution of biomass for fossil fuels in energy consumption is a measure to mitigate global warming, and political action plans at European and national levels exist for an increased use. The use of forest biomass for energy can imply different economic and environmental advantages and disadvantages for the society, the energy sector and forestry. For the achievement of an increased and sustainable use of forest biomass for energy, the EU 5th Framework project WOOD-EN-MAN aimed at synthesising current knowledge and creating new knowledge within the field

Community assessment of tropical tree biomass

DEFF Research Database (Denmark)

Theilade, Ida; Rutishauser, Ervan; Poulsen, Michael K.

2015-01-01

Background REDD+ programs rely on accurate forest carbon monitoring. Several REDD+ projects have recently shown that local communities can monitor above ground biomass as well as external professionals, but at lower costs. However, the precision and accuracy of carbon monitoring conducted by local...... communities have rarely been assessed in the tropics. The aim of this study was to investigate different sources of error in tree biomass measurements conducted by community monitors and determine the effect on biomass estimates. Furthermore, we explored the potential of local ecological knowledge to assess...... measurement, with special attention given to large and odd-shaped trees. A better understanding of traditional classification systems and concepts is required for local tree identifications and wood density estimates to become useful in monitoring of biomass and tree diversity....

Estimating Swedish biomass energy supply

International Nuclear Information System (INIS)

Johansson, J.; Lundqvist, U.

1999-01-01

Biomass is suggested to supply an increasing amount of energy in Sweden. There have been several studies estimating the potential supply of biomass energy, including that of the Swedish Energy Commission in 1995. The Energy Commission based its estimates of biomass supply on five other analyses which presented a wide variation in estimated future supply, in large part due to differing assumptions regarding important factors. In this paper, these studies are assessed, and the estimated potential biomass energy supplies are discusses regarding prices, technical progress and energy policy. The supply of logging residues depends on the demand for wood products and is limited by ecological, technological, and economic restrictions. The supply of stemwood from early thinning for energy and of straw from cereal and oil seed production is mainly dependent upon economic considerations. One major factor for the supply of willow and reed canary grass is the size of arable land projected to be not needed for food and fodder production. Future supply of biomass energy depends on energy prices and technical progress, both of which are driven by energy policy priorities. Biomass energy has to compete with other energy sources as well as with alternative uses of biomass such as forest products and food production. Technical progress may decrease the costs of biomass energy and thus increase the competitiveness. Economic instruments, including carbon taxes and subsidies, and allocation of research and development resources, are driven by energy policy goals and can change the competitiveness of biomass energy

First biomass conference of the Americas: Energy, environment, agriculture, and industry. Proceedings, Volume 3

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This conference was designed to provide a national and international forum to support the development of a viable biomass industry. Although papers on research activities and technologies under development that address industry problems comprised part of this conference, an effort was made to focus on scale-up and demonstration projects, technology transfer to end users, and commercial applications of biomass and wastes. The conference was divided into these major subject areas: Resource Base, Power Production, Transportation Fuels, Chemicals and Products, Environmental Issues, Commercializing Biomass Projects, Biomass Energy System Studies, and Biomass in Latin America. The papers in this third volume deal with Environmental Issues, Biomass Energy System Studies, and Biomass in Latin America. Concerning Environmental Issues, the following topics are emphasized: Global Climate Change, Biomass Utilization, Biofuel Test Procedures, and Commercialization of Biomass Products. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Co-gasification of biomass and coal in a pressurised fluidised bed gasifier

Energy Technology Data Exchange (ETDEWEB)

Andries, L; Hein, K R.G. [Lab. for Thermal Power Engineering, Dept. of Mechanical Engineering and Marine Technology, Delft Univ. of Technology (Netherlands)

1997-12-31

The Laboratory for Thermal Power Engineering of the Delft University of Technology is participating in an EU funded, international, R + D project which is designed to aid European industry in addressing issues regarding co-utilisation of biomass and/or waste in advanced coal conversion processes. The project comprises three main programmes, each of which includes a number of smaller subprogrammes. The three main programmes are: Coal-biomass systems component development and design; Coal-biomass environmental studies; Techno-economic assessment studies. (orig)

Co-gasification of biomass and coal in a pressurised fluidised bed gasifier

Energy Technology Data Exchange (ETDEWEB)

Andries, L.; Hein, K.R.G. [Lab. for Thermal Power Engineering, Dept. of Mechanical Engineering and Marine Technology, Delft Univ. of Technology (Netherlands)

1996-12-31

The Laboratory for Thermal Power Engineering of the Delft University of Technology is participating in an EU funded, international, R + D project which is designed to aid European industry in addressing issues regarding co-utilisation of biomass and/or waste in advanced coal conversion processes. The project comprises three main programmes, each of which includes a number of smaller subprogrammes. The three main programmes are: Coal-biomass systems component development and design; Coal-biomass environmental studies; Techno-economic assessment studies. (orig)

EVALUATION OF A PROCESS TO CONVERT BIOMASS TO METHANOL FUEL - PROJECT SUMMARY

Science.gov (United States)

The report gives results of a review of the design of a reactor capable of gasifying approximately 50 lb/hr of biomass for a pilot-scale facility to develop, demonstrate, and evaluate the Hynol Process, a high-temperature, high-pressure method for converting biomass into methanol...

Import of biomass. Obstacles to imports of biomass. A stakeholder approach. Memo. Report on BUS ticket no. 26

International Nuclear Information System (INIS)

Meeusen, M.; Kramer, K.J.; Vogelzang, T.

2004-01-01

In the discussion on imports of biomass a number of obstacles are mentioned. It is very important to know these barriers and to find out how they may be overcome. Questions to be answered are (1) Which are the main objections against import of biomass (negative impacts on biodiversity, competition with the production of food, disbalance of nutrients, etc); (2) Is it possible to quantify these objections?; and (3) What are the possibilities to overcome these barriers? The Biomass Upstream Steering committee (BUS), consisting of the participating consortium partners, was created to generate new ideas, select and rank the most promising ones to be worked out in more detail and to invite market parties to jointly set up R and D projects on upstream biomass

FY 2001 report on the new energy vision of the Ishigaki City area. Survey for working out 'the project for the introduction of biomass energy in the central urban area of Ishigaki City'; 2001 nendo Ishigaki shi chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

Study was made of potentialities of the project of 'an energy supply system for biomass energy using business-derived raw refuse' indicated in 'the new energy vision of Ishigaki City, Okinawa Prefecture.' The amount of the recovered business-derived raw refuse was set at 5.6t at the minimum as against the discharged amount of 8t, and it was calculated that the amount of the biogas generated from the high temperature methane fermentation would be 757.7 m{sup 3}/d. The amount of the suppliable energy calculated from the above was 1,102.4 kWh/d in gas engine. Further, as to the energy demand, supposing the energy demand in large-scale hot bath facilities using salt as a resource of the area, it was calculated that the energy demand would be approximately 1MWh/d altogether with that in the biogas plant. As a result of the study of profitability of the project, the following was found out: it takes 25 years to recover the invested capital in the case of carrying out the biogas plant project alone and 18 years to recover it in the case of carrying out the hot bath facility project alone. In the case of carrying out both projects as one, it takes 18 years to recover the invested capital, the same as in the case of carrying out the hot bath facility project alone, but a great shortage from 6 years to 3 years is shown of the period required to get out of the cumulative deficit. (NEDO)

Production of methanol/DME from biomass

Energy Technology Data Exchange (ETDEWEB)

Ahrenfeldt, J.; Birk Henriksen, U.; Muenster-Swendsen, J.; Fink, A.; Roengaard Clausen, L.; Munkholt Christensen, J.; Qin, K.; Lin, W.; Arendt Jensen, P.; Degn Jensen, A.

2011-07-01

In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier types have been investigated in this project: 1) The Two-Stage Gasifier (Viking Gasifier), designed to produce a very clean gas to be used in a gas engine, has been connected to a lab-scale methanol plant, to prove that the gas from the gasifier could be used for methanol production with a minimum of gas cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51-58% (LHV). By using waste heat from the plants for district heating, the total energy efficiencies could reach 87-88% (LHV). 2) A lab-scale electrically heated entrained flow gasifier has been used to gasify wood and straw. Entrained flow gasifiers are today the preferred gasifier type for commercial coal gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic fraction of the biomass that is not converted to gas appears as soot. Thermodynamic computer models of DME and methanol plants based on using entrained flow gasification were created to show the potential of such plants. These models showed that the potential torrefied biomass to DME/methanol + net electricity energy efficiency was 65-71% (LHV). Different routes to produce liquid transport fuels from biomass are possible. They include production of RME (rapeseed oil

Wood biomass gasification: Technology assessment and prospects in developing countries

International Nuclear Information System (INIS)

Salvadego, C.

1992-05-01

This investigation of the technical-economic feasibility of the development and use of wood biomass gasification plants to help meet the energy requirements of developing countries covers the following aspects: resource availability and production; gasification technologies and biomass gasification plant typology; plant operating, maintenance and safety requirements; the use of the biomass derived gas in internal combustion engines and boilers; and the nature of energy requirements in developing countries. The paper concludes with a progress report on biomass gasification research programs being carried out in developing countries world-wide

Moisture Metrics Project

Energy Technology Data Exchange (ETDEWEB)

Schuchmann, Mark

2011-08-31

the goal of this project was to determine the optimum moisture levels for biomass processing for pellets commercially, by correlating data taken from numerous points in the process, and across several different feedstock materials produced and harvested using a variety of different management practices. This was to be done by correlating energy consumption and material through put rates with the moisture content of incoming biomass ( corn & wheat stubble, native grasses, weeds, & grass straws), and the quality of the final pellet product.This project disseminated the data through a public website, and answering questions form universities across Missouri that are engaged in biomass conversion technologies. Student interns from a local university were employed to help collect data, which enabled them to learn firsthand about biomass processing.

Estimation of crown biomass of Pinus pinaster stands and shrubland above-ground biomass using forest inventory data, remotely sensed imagery and spatial prediction models

Science.gov (United States)

H. Viana; J. Aranha; D. Lopes; Warren B. Cohen

2012-01-01

Spatially crown biomass of Pinus pinaster stands and shrubland above-ground biomass (AGB) estimation was carried-out in a region located in Centre-North Portugal, by means of different approaches including forest inventory data, remotely sensed imagery and spatial prediction models. Two cover types (pine stands and shrubland) were inventoried and...

A Hybrid Catalytic Route to Fuels from Biomass Syngas

Energy Technology Data Exchange (ETDEWEB)

Harmon, Laurel [LanzaTech, Inc., Skokie, IL (United States); Hallen, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lilga, Michael [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Heijstra, Bjorn [LanzaTech, Inc., Skokie, IL (United States); Palou-Rivera, Ignasi [LanzaTech, Inc., Skokie, IL (United States); Handler, Robert [Michigan Technological Univ., Houghton, MI (United States)

2017-12-31

LanzaTech partnered with the Pacific Northwest National Laboratory (PNNL), Imperium Aviation Fuels, InEnTec, Orochem Technologies, the University of Delaware, Michigan Technological University, the National Renewable Energy Laboratory, and The Boeing Company, to develop a cost-effective hybrid conversion technology for catalytic upgrading of biomass-derived syngas to sustainable alternative jet fuel (SAJF) meeting the price, quality and environmental requirements of the aviation industry. Alternative “synthetic paraffinic kerosene” (SPK) blendstock produced from syngas via “Fischer-Tropsch” (F-T) or from lipids via “hydroprocessing of esters and fatty acids” (HEFA) are currently being used in commercial jet fuel blends containing at least 50% petroleum-based fuel. This project developed an alternative route to SAJF from ethanol, a type of “alcohol to jet” (ATJ) SPK. The project objective was to demonstrate a pathway that combines syngas fermentation to ethanol with catalytic upgrading of ethanol to sustainable alternative jet fuel and shows attractive overall system economics to drive down the price of biomass-derived jet fuel. The hybrid pathway was to be demonstrated on three biomass feedstocks: corn stover, woody biomass, and third biomass feedstock, cellulosic residues. The objective also included the co-production of chemicals, exemplified by 2,3-Butanediol (2,3-BDO), which can be converted to key chemical intermediates. The team successfully demonstrated that biomass syngas fermentation followed by catalytic conversion is a viable alternative to the Fischer-Tropsch process and produces a fuel with properties comparable to F-T and HEFA SPKs. Plasma gasification and gas fermentation were successfully integrated and demonstrated in continuous fermentations on waste wood, corn stover, and cellulosic bagasse. Gas fermentation was demonstrated to produce ethanol suitable for catalytic upgrading, isolating the upgrading from variations in biomass

Thermodynamic analysis of hydrogen production from biomass gasification

International Nuclear Information System (INIS)

Cohce, M.K.; Dincer, I.; Rosen, M.A.

2009-01-01

'Full Text': Biomass resources have the advantage of being renewable and can therefore contribute to renewable hydrogen production. In this study, an overview is presented of hydrogen production methods in general, and biomass-based hydrogen production in particular. For two methods in the latter category (direct gasification and pyrolysis), assessments are carried out, with the aim of investigating the feasibility of producing hydrogen from biomass and better understanding the potential of biomass as a renewable energy source. A simplified model is presented here for biomass gasification based on chemical equilibrium considerations, and the effects of temperature, pressure and the Gibbs free energy on the equilibrium hydrogen yield are studied. Palm oil (designated C 6 H 10 O 5 ), one of the most common biomass resources in the world, is considered in the analyses. The gasifier is observed to be one of the most critical components of a biomass gasification system, and is modeled using stoichiometric reactions. Various thermodynamic efficiencies are evaluated, and both methods are observed to have reasonably high efficiencies. (author)

Biomass energy development and carbon dioxide mitigation options

International Nuclear Information System (INIS)

Hall, D.O.; House, J.I.

1995-01-01

Studies on climate change and energy production increasingly recognize the crucial role of biological systems. Carbon sinks in forests (above and below ground), CO 2 emissions from deforestation, planting trees for carbon storage, and biomass as a substitute for fossil fuels are some of the key issues which arise. Halting deforestation is of paramount importance, but there is also great potential for reforestation of degraded lands, agroforestry and improved forest management. We conclude that biomass energy plantations and other types of energy cropping could be a more effective strategy for carbon mitigation than simply growing trees as a carbon store. Using the biomass for production of modern energy carriers such as electricity, and liquid and gaseous fuels also has a wide range of other environmental, social and economic benefits. In order for biomass projects to succeed, it is necessary to ensure that these benefits are felt locally as well as nationally, furthermore, environmental sustainability of bioenergy projects is an essential requirement. The constraints to achieving environmentally-acceptable biomass production are not insurmountable. Rather they should be seen as scientific and entrepreneurial opportunities which will yield numerous advantages at local, national and international levels in the long term. (au) 76 refs

BARRIER ISSUES TO THE UTILIZATION OF BIOMASS; SEMIANNUAL

International Nuclear Information System (INIS)

Bruce C. Folkedahl; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

2001-01-01

The Energy and Environmental Research Center (EERC) is conducting a project to examine the fundamental issues limiting the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC is attempting to elucidate the ash-related problems-grate clinkering and heat exchange surface fouling-associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low volatile fuels with lower reactivities can experience damaging fouling when switched to higher volatile and more reactive lower-rank fuels, such as when cofiring biomass. Higher heat release rates at the grate can cause more clinkering or slagging at the grate because of higher temperatures. Combustion and loss of volatile matter can start too early for biomass fuels compared to the design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates and various chlorides, in combination with different flue gas temperatures because of changes in fuel heating value which can adversely affect ash deposition behavior. The goal of this project is to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass-specifically wood and agricultural residuals-in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project are: Modification of an existing EERC pilot-scale combustion system to simulate a grate-fired system; Verification testing of the simulator; Laboratory-scale testing and fuel characterization to determine ash

Power generation from biomass: Status report on catalytic-allothermal wood gasification. Papers; Energetische Nutzung von Biomasse: Stand der Realisierung der katalytisch-allothermen Holzvergasung. Vortraege

Energy Technology Data Exchange (ETDEWEB)

Spindler, H.; Bauermeister, U.; Kliche, H.; Seiffarth, K. (comps.)

2001-12-01

The topic of this event is bound up with the activities of FOeST in the field of gasification of biomass in decentralized small plants (< 2 MW{sub el}). The start project was a research work in 1993 to select a gasification process for using wood, sludge or plastic waste, continued 1995 by a research project with gasification tests of tar oil contaminated wood in a small gasification reactor with good results in environmental compatibility. But the following planning process of a demonstration plant for 500 kW{sub el} has shown, that the biomass gasification couldn't reach economic efficiency. Due to the development of an catalytic-partial allothermal gasification process of GNS ltd. it was clear, that the technical efficiency could be increased considerably. So, in 2000, a project started to test this catalytic-partial allothermal gasification in a pilot plant. Today the results of research, development and testing of biomass gasification with catalytic-partial allothermal processing as well as practically experience with a gasification plant, general conditions and further activities for energetically utilisation of biomass in Saxonia-Anhalt will be presented. (orig.)

Energy from biomass and waste

International Nuclear Information System (INIS)

1991-01-01

This report provides a review of the Commission of the European Communities (CEC) Energy Demonstration Programme in the sector of Energy from biomass and waste, and examines the current status of the energy technologies associated with the sector, in relation to projects supported under the Programme, those included under various national programmes and by reference to the published literature. Detailed overviews of five sub-categories represented in the Energy from biomass and waste sector are presented to illustrate their relative significance in terms of estimated energy potential, technological and economic status and the nature of future research, development and demonstration needs. Finally the potential role of the biomass and waste energy technologies in meeting the energy needs of the developing world is discussed. 33 refs; 2 figs; 11 tabs

Small-scale bioenergy projects in rural China: Lessons to be learnt

International Nuclear Information System (INIS)

Han Jingyi; Mol, Arthur P.J.; Lu Yonglong; Zhang Lei

2008-01-01

Large amounts of small-scale bioenergy projects were carried out in China's rural areas in light of its national renewable energy policies. These projects applied pyrolysis gasification as the main technology, which turns biomass waste at low costs into biogas. This paper selects seven bioenergy projects in Shandong Province as a case and assesses these projects in terms of economy, technological performance and effectiveness. Results show that these projects have not achieved a satisfying performance after 10 years experience. Many projects have been discontinued. This failure is attributed to a complex of shortcomings in institutional structure, technical level, financial support and social factors. For a more successful future development of bioenergy in rural areas, China should reform its institutional structure, establish a renewable energy market and enhance the technological level of bioenergy projects

Biomass gasification for production of 'green energy'

International Nuclear Information System (INIS)

Mambre, V.

2008-01-01

This paper presents the differences between biomass gasification and biomass methanation, two ways of using biomass for decentralized production of energy. The stakes of biomass and biomass gasification for meeting the European and national energy goals and environmental targets are summarized. The gasification principle is described and in particular the FICFB optimized process from Repotec for the production of concentrated syngas. The four different ways of syngas valorization (combined heat and power (CHP), 'green methane' (SNG), 'green hydrogen' (gas shift) and liquid biofuels of 2. generation (Fisher-Tropsch)) are recalled and compared with each other. Finally, the economical and environmental key issues of the global chain are summarized with their technological and scientific key locks. The GAYA R and D project of Gaz de France Suez group, which aims at developing gasification and methanation demonstration plants through different programs with European partners, is briefly presented. (J.S.)

High Temperature Corrosion in Biomass Incineration Plants

DEFF Research Database (Denmark)

Montgomery, Melanie; Maahn, Ernst emanuel; Gotthjælp, K.

1997-01-01

The aim of the project is to study the role of ash deposits in high temperature corrosion of superheater materials in biomass and refuse fire combined heat and power plants. The project has included the two main activities: a) A chemical characterisation of ash deposits collected from a major...

Northeast Regional Biomass Program. Final progress report, July--September 1991

Energy Technology Data Exchange (ETDEWEB)

O`Connell, R.A.

1991-11-01

The management structure and program objectives for the Northeast Regional Biomass Program (NRBP) remain unchanged from previous years. Additional funding was provided by the Bonneville Power Administration Regional Biomass Program to continue the publication of articles in the Biologue. The Western Area Power Administration and the Council of Great Lakes Governors funded the project ``Characterization of Emissions from Burning Woodwaste``. A grant for the ninth year was received from DOE. The Northeast Regional Biomass Steering Committee selected the following four projects for funding for the next fiscal year. (1) Wood Waste Utilization Conference, (2) Performance Evaluation of Wood Systems in Commercial Facilities, (3) Wood Energy Market Utilization Training, (4) Update of the Facility Directory.

Catalytic Production of Ethanol from Biomass-Derived Synthesis Gas

Energy Technology Data Exchange (ETDEWEB)

Trewyn, Brian G. [Colorado School of Mines, Golden, CO (United States); Smith, Ryan G. [Iowa State Univ., Ames, IA (United States)

2016-06-01

Heterogeneous catalysts have been developed for the conversion of biomass-derived synthetic gas (syngas) to ethanol. The objectives of this project were to develop a clean synthesis gas from biomass and develop robust catalysts with high selectivity and lifetime for C₂ oxygenate production from biomass-derived syngas and surrogate syngas. During the timeframe for this project, we have made research progress on the four tasks: (1) Produce clean bio-oil generated from biomass, such as corn stover or switchgrass, by using fast pyrolysis system, (2) Produce clean, high pressure synthetic gas (syngas: carbon monoxide, CO, and hydrogen, H₂) from bio-oil generated from biomass by gasification, (3) Develop and characterize mesoporous mixed oxide-supported metal catalysts for the selective production of ethanol and other alcohols, such as butanol, from synthesis gas, and (4) Design and build a laboratory scale synthesis gas to ethanol reactor system evaluation of the process. In this final report, detailed explanations of the research challenges associated with this project are given. Progress of the syngas production from various biomass feedstocks and catalyst synthesis for upgrading the syngas to C₂-oxygenates is included. Reaction properties of the catalyst systems under different reaction conditions and different reactor set-ups are also presented and discussed. Specifically, the development and application of mesoporous silica and mesoporous carbon supports with rhodium nanoparticle catalysts and rhodium nanoparticle with manganese catalysts are described along with the significant material characterizations we completed. In addition to the synthesis and characterization, we described the activity and selectivity of catalysts in our micro-tubular reactor (small scale) and fixed bed reactor (larger scale). After years of hard work, we are proud of the work done on this project, and do believe that this work will provide a solid

Production of Solid sustainable Energy Carriers from biomass by means of TORrefaction (SECTOR)

Energy Technology Data Exchange (ETDEWEB)

Witt, Janet; Bienert, Kathrin [DBFZ Deutsches Biomasseforschungszentrum gemeinnuetzige GmbH, Leipzig (Germany). Bereich Bioenergiesysteme; Zwart, Robin; Kiel, Jaap; Englisch, Martin; Wojcik, Magdalena

2012-07-01

SECTOR is a large-scale European project with a strong consortium of over 20 partners from industry and science. The project is focussed on the further development of torrefaction-based technologies for the production of solid bioenergy carriers up to pilot-plant scale and beyond, and on supporting the market introduction of torrefaction-based bioenergy carriers as a commodity renewable solid fuel. The torrefaction of biomass materials is considered to be a very promising technology for the promotion of the large-scale implementation of bioenergy. During torrefaction biomass is heated up in the absence of oxygen to a temperature of 250-320 C. By combining torrefaction with pelletisation or briquetting, biomass materials can be converted into a high-energy-density commodity solid fuel or bioenergy carrier with improved behaviour in (long-distance) transport, handling and storage, and also with superior properties in many major end-use applications. Torrefaction has the potential to provide a significant contribution to an enlarged raw material portfolio for biomass fuel production inside Europe by including both agricultural and forestry biomass. In this way, the SECTOR project is expected to shorten the time-to-market of torrefaction technology and to promote market introduction within stringent sustainability boundary conditions. The European Union provides funding for this project within the Seventh Framework Programme. The project has a duration of 42 months and started in January 2012. (orig.)

NEDO hydrogen, alcohol, and biomass technology subcommittee. 18th project report meeting; NEDO suiso alcohol biomass gijutsu bunkakai. Dai 18 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

A report is delivered by Morio Murase, a NEDO (New Energy and Industrial Technology Development Organization) director, in which the general situation of hydrogen, alcohol, and biomass technology development is explained. Concerning the research and development of international clean energy system of hydrogen, the WE-NET (World Energy Network) project is described, in which a total system concept design and cryogenic structural materials that are the fruits of the 1st phase are mentioned. Concerning the 2nd phase, research and development to be conducted are discussed, and reports are delivered thereon. Reported concerning the development of high-efficiency refuse-fueled power generation technology are a demonstration test using a pilot plant and a superheater demonstration test. Concerning the research and development for the advanced clear energy vehicle project, a development program is reported for an energy-efficient, low-pollution vehicle which is a combination of a hybrid mechanism and clean energy. Reported also is the research and development of supercritical fluid utilization, in which the reaction of supercritical water upon addition of solvent, its oxidation and hydrogenation, and so forth, are explained. (NEDO)

Survey sustainability Biomass. Appendix. Results of the international respondents

Energy Technology Data Exchange (ETDEWEB)

Bergsma, G.C.; Groot, M.I.

2006-06-15

As part of an array of strategies to combat climate change, biomass is being used increasingly as a substitute for fossil fuels. It is important that the sustainability benefits thus accruing to the Netherlands are not at the expense of sustainable development in producer countries. Against this background the 'Sustainable biomass imports' project group is developing a set of criteria for evaluating the sustainability of biomass projects. To assess support for such criteria, CE conducted an internet survey among the various stakeholders (NGOs, industry, government), drawing a total of 104 responses. This report presents all the results and conclusions of the survey, for each category of stakeholders and overall. Among the most striking conclusions are the following: The majority of respondents see a sustainability audit on biomass as feasible, provided the sustainability criteria are adequate for the purpose (68%); Almost all the respondents are of the opinion that such sustainability criteria should apply to all applications of biomass (90%); On the issue of whether these criteria should vary according to the producer region concerned, respondents were divided (50% for, 50% against); Many NGOs state there should be different sustainability criteria in force for different biomass flows (50%), in contrast to industry, which argues for a uniform set of criteria for all flows; Most respondents hold that any biomass criteria should apply to both subsidised and unsubsidised projects; At the same time, a sizable majority of respondents state that subsidisation of biomass projects should depend on the degree of sustainability (72%) and in particular on the CO2 emission cuts achieved, this being regarded as the single most important factor; When it comes to the issue of GMO, opinions differ markedly between NGOs and industry, with some 75% of NGOs wanting this aspect included, but only 10% of industry; Respondents also commented on a number of additional issues

Hydrothermal Liquefaction of Biomass

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.

2010-12-10

Hydrothermal liquefaction technology is describes in its relationship to fast pyrolysis of biomass. The scope of work at PNNL is discussed and some intial results are presented. HydroThermal Liquefaction (HTL), called high-pressure liquefaction in earlier years, is an alternative process for conversion of biomass into liquid products. Some experts consider it to be pyrolysis in solvent phase. It is typically performed at about 350 C and 200 atm pressure such that the water carrier for biomass slurry is maintained in a liquid phase, i.e. below super-critical conditions. In some applications catalysts and/or reducing gases have been added to the system with the expectation of producing higher yields of higher quality products. Slurry agents ('carriers') evaluated have included water, various hydrocarbon oils and recycled bio-oil. High-pressure pumping of biomass slurry has been a major limitation in the process development. Process research in this field faded away in the 1990s except for the HydroThermal Upgrading (HTU) effort in the Netherlands, but has new resurgence with other renewable fuels in light of the increased oil prices and climate change concerns. Research restarted at Pacific Northwest National Laboratory (PNNL) in 2007 with a project, 'HydroThermal Liquefaction of Agricultural and Biorefinery Residues' with partners Archer-Daniels-Midland Company and ConocoPhillips. Through bench-scale experimentation in a continuous-flow system this project investigated the bio-oil yield and quality that could be achieved from a range of biomass feedstocks and derivatives. The project was completed earlier this year with the issuance of the final report. HydroThermal Liquefaction research continues within the National Advanced Biofuels Consortium with the effort focused at PNNL. The bench-scale reactor is being used for conversion of lignocellulosic biomass including pine forest residue and corn stover. A complementary project is an international

Analysis of the availability of biomass in Cuba with energy ends

International Nuclear Information System (INIS)

Pla Duporte, Manuel; Arango, Mirta; Guyat Dupuy, Maria Antonia

2011-01-01

The quick decrease of the fossil fuels has taken to the search of renewable sources of energy. Cuba has in the biomasses one of the biggest potentialities of sources renewable of energy, but even with a small exploitation. The purpose of increasing the employment of the sources renewable of energy, in particular the biomasses one requires evaluation of the capacities with which it counts our country. Presently work the results of an are presented The study carried out directed to the evaluation of these sources focused basically to the possibility of their employment in processes thermochemical. The evaluation of the is attacked availability of these energy resources, their main ones characteristic, the potentialities are also determined of use of the selected biomasses. Equally you it makes an estimate of the availability of the biomasses chosen in dependence of the behavior of its consumption, for finally to carry out an appreciation of the one potential of energy obtaining starting from her and its technician-economic feasibility. (author)

Production of field biomass on the fields and mires and its utilization in energy production; Biomassan tuotanto pelloilla ja soilla sekae kaeyttoe energiantuotantoon

Energy Technology Data Exchange (ETDEWEB)

Mela, T.; Hoemmoe, L.; Suokangas, A. [Agricultural Research Centre, Helsinki (Finland)

1997-12-01

The research will be carried out as five sub-projects. The first sub-project `Breeding of reed canary grass and it`s nutrient balance` is concentrated in the development of new reed canary grass cultivars as well as new fertilization practices for non food production. In sub-project no. 2 `Cultivation of reed canary grass at the mire and the drying of peat production area` the evaporation potential of reed canary grass in connection with the drying of peat production area as well as the use of reed canary grass in purifying the runoff coming from the peat production areas was studied. In sub-project no. 3 `Development of a new efficient harvesting method and technology for straw biomass` various harvesting-transport chains based on different balers and choppers as well as economics of these chains were studied. The economics of the production-utilization chains were studied under the sub-project no. 4 `The economics of-reed canary grass and straw production- harvesting-transport-chains and their availability for bioenergy production`. The availability of reed canary grass and straw for energy production was studied by determining the amount of potential production area near the power plants capable of biomass combustion. In the sub-project no. 5 `Fuel and combustion properties of reed canary grass` the combustion quality of spring harvested reed canary grass turned out to be much better than the quality of autumn harvested grass. The full scale combustion experiments with efficiency and emission determinations were carried out at Kiuruvesi using the mixture of reed canary grass and wood chips (and bark) as a fuel

BIOMASS REBURNING - MODELING/ENGINEERING STUDIES

International Nuclear Information System (INIS)

Vladimir Zamansky; David Moyeda; Mark Sheldon

2000-01-01

This project is designed to develop engineering and modeling tools for a family of NO(sub x) control technologies utilizing biomass as a reburning fuel. During the tenth reporting period (January 1-March 31, 2000), EER and NETL R and D group continued to work on Tasks 2, 3, 4, and 5. Information regarding these tasks will be included in the next Quarterly Report. This report includes (Appendix 1) a conceptual design study for the introduction of biomass reburning in a working coal-fired utility boiler. This study was conducted under the coordinated SBIR program funded by the U. S. Department of Agriculture

Ashes of biomass combustion. Report of a workshop at 15 May 1997

International Nuclear Information System (INIS)

Zeevalkink, J.A.

1997-12-01

In a previous study the results of a study on the options to recycle or re-use ashes from biomass combustion were presented. Those results were discussed in detail in the title workshop, attended by researchers, market representatives that have to find practical solutions, and representatives of the Dutch government. It is concluded that only ashes from clean biomass can be used as a fertilizer (e.g. recycling of the ashes to forest soils), preferably in the form of granulated materials to realize a slow uptake of nutrients. Bottom ash can be applied in road construction materials or in concretes. In the appendices of this report sheets of 4 contributions are presented: ' Re-use of ashes form biomass combustion'; The Vattenfall project. Closing of the cycle in Sweden'; 'The vision of a biomass producer'; and ' The market problems for the initiator of biomass projects'. 3 appendices

Stakeholder perspectives on converting forest biomass to energy in Oregon, USA

Energy Technology Data Exchange (ETDEWEB)

Stidham, Melanie; Simon-Brown, Viviane [Department of Forest Ecosystems and Society, College of Forestry, Oregon State University, 321 Richardson Hall, Corvallis, OR 97331 (United States)

2011-01-15

Within the state of Oregon, USA, there is considerable interest in the possibility of converting forest biomass to energy. A number of studies have assessed the technical feasibility of forest biomass energy, but few have focused on social aspects, an important consideration in projects involving public forests. This study explores the social context of converting forest biomass to energy, using qualitative research methods. Semi-structured interviews were conducted with forty individuals representing nine different stakeholder groups. Information gained through interviews was used to understand stakeholder views on forest biomass energy, including their perspectives on potential barriers and opportunities in Oregon. Findings indicate the most challenging barrier will be access to long-term, consistent supply. A related challenge is the long history of contention between parties over forest products coming from public lands. However, findings also show that there are many areas of common ground between these groups that have historically been at odds, such as agreement on the necessity of restoration treatments in certain forest types, the by-product of which could be used for biomass generation. Potential conflicts still exist, for instance over projects in mixed conifer forests. Development of policies and projects through inclusive, collaborative approaches could alleviate controversies, potentially allowing more activities to move forward. Information provided by this research creates a foundation for discussions as forest biomass energy becomes an increasingly prominent issue in Oregon, the western USA, and other regions of the world. (author)

ASEAN grid-connected biomass residues fired cogeneration plants

International Nuclear Information System (INIS)

Adnan, M.F.; Alias, R.

2006-01-01

Energy supply is one of the major concerns in the world. With uncertainty in the main oil suppliers, the oil price is expected to remain high due to continuous demand from the world. Since oil is mostly used for electricity and transportation, its shortage would cause major disruptions in our daily activities. Thus to counter this scenario and faster depletion of fossil fuel resources, various measures have been taken to find alternative source of energy such as renewable energy. One of the renewable energy sources is from biomass residues which is aplenty particularly in ASEAN. Through one of the collaboration programme between ASEAN and EC which is The EC-ASEAN Cogeneration Programme, a number of Full-Scale Demonstration Projects (FSDP) using biomass residues have been commissioned and implemented successfully. Four of the FSDPs in Thailand and Malaysia are connected to the grid. These projects have been operating very well and since the fuel is commonly available in this ASEAN region, duplication should not be a problem. Thus, this paper would highlight the success stories in implementing biomass residues grid connected project while enhancing cooperation between ASEAN and EC. (Author)

BioRefine. New biomass products programme 2007-2012. Final report

Energy Technology Data Exchange (ETDEWEB)

Makinen, T. (ed.) [VTT Technical Research Centre of Finland, Espoo (Finland); Alakangas, E.; Holviala, N. (eds.) [VTT Technical Research Centre of Finland, Jyvaskyla (Finland)

2012-07-01

The focal areas of the BioRefine programme have been business development, raw materials, and product lines. The key issue in the programme has been the development of business opportunities. The other two programme areas - raw materials and product lines, including technologies and services - have always been viewed from the perspective of short, medium or long-term business activities.The programme has organised four calls for research projects. The focus of the first call was on biomass-based fuels for transport (in the autumn 2007), the second one focused on other biomass-based products like chemicals and materials (in the spring 2008), and the third one on new biomass sources and waste-based biomass, and research supporting the business development of SME companies (early in 2010). In the last call in the spring 2011, project proposals were expected to focus on the following areas: new innovative and multidisciplinary research initiatives related to biomass utilisation, small distributed biorefinery concepts, efficient and sustainable utilisation of biomass raw materials in new integrated solutions for biorefining, and new integrated solutions for the efficient utilisation of sidestreams in the biorefining value chain or in its parts. Unlike research organizations, companies have been able to apply for funding continuously from Tekes.

Pyrolysis Dynamics of Biomass Residues in Hot-Stage

Directory of Open Access Journals (Sweden)

Ivan Bergier

2015-09-01

Full Text Available Original data for mass, element, and methane dynamics under controlled pyrolysis are presented for several biomass feedstocks. The experimental system consisted of an environmental (low-vacuum scanning electron microscopy (ESEM with a hot-stage and energy-dispersive X-ray spectroscopy (EDS detector. A tunable diode laser (TDL was coupled to the ESEM vacuum pump to measure the methane partial pressure in the exhaust gases. Thermogravimetric analysis and differential thermal analysis (TG/DTA in a N2 atmosphere was also carried out to assess the thermal properties of each biomass. It was found that biochars were depleted or enriched in specific elements, with distinct methane formation change. Results depended on the nature of the biomass, in particular the relative proportion of lignocellulosic materials, complex organic compounds, and ash. As final temperature was increased, N generally decreased by 30 to 100%, C increased by 20 to 50% for biomass rich in lignocellulose, and P, Mg, and Ca increased for ash-rich biomass. Methane formation also allows discriminating structural composition, providing fingerprints of each biomass. Biomass with low ashes and high lignin contents peaks CH4 production at 330 and 460 °C, whereas those biomasses with high ashes and low lignin peaks CH4 production at 330 and/or 400 °C.

Digital Biomass Accumulation Using High-Throughput Plant Phenotype Data Analysis.

Science.gov (United States)

Rahaman, Md Matiur; Ahsan, Md Asif; Gillani, Zeeshan; Chen, Ming

2017-09-01

Biomass is an important phenotypic trait in functional ecology and growth analysis. The typical methods for measuring biomass are destructive, and they require numerous individuals to be cultivated for repeated measurements. With the advent of image-based high-throughput plant phenotyping facilities, non-destructive biomass measuring methods have attempted to overcome this problem. Thus, the estimation of plant biomass of individual plants from their digital images is becoming more important. In this paper, we propose an approach to biomass estimation based on image derived phenotypic traits. Several image-based biomass studies state that the estimation of plant biomass is only a linear function of the projected plant area in images. However, we modeled the plant volume as a function of plant area, plant compactness, and plant age to generalize the linear biomass model. The obtained results confirm the proposed model and can explain most of the observed variance during image-derived biomass estimation. Moreover, a small difference was observed between actual and estimated digital biomass, which indicates that our proposed approach can be used to estimate digital biomass accurately.

Biomass power for rural development. Quarterly report, July 1--September 30, 1998

Energy Technology Data Exchange (ETDEWEB)

Cooper, J.T.

1998-10-01

In this quarter a large amount of time was spent doing project planning and budget preparation for the fiscal years 1998 and 1999. Many issues of long-term strategic planning and budgeting depend on the availability of Federal support, including financial, technical and political. It has become increasingly obvious that several significant barriers must be overcome in order to reach the final project goal of commercial replication of the technology. This report describes switchgrass conversion development, production activities, environmental analysis planning, and information and education. Appendices discuss the biomass project, sediment delivery, successful establishment of switchgrass, and legislative support for the biomass project.

Importance of biomass energy sources for Turkey

International Nuclear Information System (INIS)

Demirbas, Ayhan

2008-01-01

Various agricultural residues such as grain dust, crop residues and fruit tree residues are available in Turkey as the sources of biomass energy. Among the biomass energy sources, fuelwood seems to be one of the most interesting because its share of the total energy production of Turkey is high at 21% and the techniques for converting it to useful energy are not necessarily sophisticated. Selection of a particular biomass for energy requirements is influenced by its availability, source and transportation cost, competing uses and prevalent fossil fuel prices. Utilization of biomass is a very attractive energy resource, particularly for developing countries since biomass uses local feedstocks and labor. Like many developing countries, Turkey relies on biomass to provide much of its energy requirement. More efficient use of biomass in producing energy, both electrical and thermal, may allow Turkey to reduce petroleum imports, thus affecting its balance of payments dramatically. Turkey has always been one of the major agricultural countries in the world. The importance of agriculture is increasing due to biomass energy being one of the major resources in Turkey. Biomass waste materials can be used in Turkey to provide centralized, medium- and large-scale production of process heat for electricity production. Turkey's first biomass power project is under development in Adana province, at an installed capacity of 45 MW. Two others, at a total capacity of 30 MW, are at the feasibility study stage in Mersin and Tarsus provinces. Electricity production from biomass has been found to be a promising method in the nearest future in Turkey

Economical analyses of construction of a biomass boiler house

International Nuclear Information System (INIS)

Normak, A.

2002-01-01

To reduce the energy costs we can use cheaper fuel to fire our boiler. One of the cheapest fuels is wood biomass. It is very actual issue how to use cheaper wood biomass in heat generation to decrease energy costs and to increase biomass share in our energy balance. Before we decide to build biomass boiler house it is recommendable to analyse the economical situation and work out most profitable, efficient, reliable and ecological boiler plant design on particular conditions. The best way to perform the analyses is to use the economical model presented. It saves our time and gives objective evaluation to the project. (author)

Experimental comparison of biomass chars with other catalysts for tar reduction

NARCIS (Netherlands)

Abu El-Rub, Ziad; Bramer, Eduard A.; Brem, Gerrit

2008-01-01

In this paper the potential of using biomass char as a catalyst for tar reduction is discussed. Biomass char is compared with other known catalysts used for tar conversion. Model tar compounds, phenol and naphthalene, were used to test char and other catalysts. Tests were carried out in a fixed bed

Short-rotation Willow Biomass Plantations Irrigated and Fertilised with Wastewaters. Results from a 4-year multidisciplinary field project in Sweden, France, Northern Ireland and Greece

Energy Technology Data Exchange (ETDEWEB)

Larsson, Stig [Svaloef Weibull AB, Svaloef (Sweden); Cuingnet, Christian; Clause, Pierre [Association pour le Developpement des Culture Energetiques, Lille (France); Jakobsson, Ingvar [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden); Dawson, Malcolm [Queens Univ., Northern Ireland (United Kingdom); Backlund, Arne [A and B Backlund ApS, Charlottenlund (Denmark); Mavrogianopoulus, George [Agricultural Univ. of Athens (Greece)

2003-01-01

This report summarises results and experiences gathered from field trials with recycling of pre-treated wastewater, diverted human urine mixed with water, and municipal sludge, within plantations of willow species specifically selected for biomass production. Experimental sites were established in Sweden (Roma), France (Orchies), Northern Ireland (Culmore) and Greece (Larissa). The project was carried out during a 4-year period with financial support from the EU FAIR Programme. The experimental sites were supplied with primary effluent from municipal treatment plants (Culmore and Larissa), stored industrial effluent from a chicory processing plant (Orchies), biologically treated and stored municipal wastewater (Roma) and human urine mixture from diverting low-flush toilets mixed with water (Roma). Application rates of the wastewaters or the urine mixture were equivalent to the calculated evapotranspiration rate at each site. Wastewaters were also applied up to three times this value to evaluate any possible negative effects. Estimations and evaluations were carried out mainly concerning: biomass growth, potential biological attacks of the plantations, plant water requirements, fertilisation effects of the wastewater, plant uptake of nutrients and heavy metals from applied wastewater, possible soil or groundwater impact, sanitary aspects, and potentials for removal in the soil-plant filter of nutrients and biodegradable organic material from applied wastewater. The results clearly indicated that biomass production in young willow plantations could be enhanced substantially after recycling of wastewater resources. The impact on soil and groundwater of nutrients (nitrogen and phosphorus) and heavy metals (copper, zinc, lead and cadmium) was limited, even when the application of water and nutrients exceeded the plant requirements. Also, the soil-plant system seemed to function as a natural treatment filter for pre-treated (primary settled) wastewater, with a treatment

Biomass energy consumption in Nigeria: integrating demand and supply

International Nuclear Information System (INIS)

Momoh, S.; Soaga, J.

1999-01-01

The study examined the present and future consumption of biomass energy in Nigeria. Direct consumption of fire wood for domestic purposes is the predominant form of biomass energy consumption. Charcoal plays minot roles in biomass energy supply. The current and expected demand for fuelwood is projected to increase by 399% whereas supply is expected to decrease by 17.2% between 1995 and year 2010. Resource adequacy in terms of planned supply is on the decline. Forest estates which is the only planned strategy for fuelwood and wood production is projected to decline from 6.37 million ha. in 1990 to 2.4 million ha, in year 2010. The possibilities of meeting the fuelwood demand in the future is precarious. Policy measures aimed at increasing forest estates. reduction of loss of forest lands to other uses and encouragement of private forestry are recommended

Review: Assessing the climate mitigation potential of biomass

Directory of Open Access Journals (Sweden)

Patrick Moriarty

2016-12-01

Full Text Available For many millennia, humans have used biomass for three broad purposes: food for humans and fodder for farm animals; energy; and materials. Food has always been exclusively produced from biomass, and in the year 1800, biomass still accounted for about 95% of all energy. Biomass has also been a major source of materials for construction, implements, clothing, bedding and other uses, but some researchers think that total human uses of biomass will soon reach limits of sustainability. It is thus important to select those biomass uses that will maximise global climate change benefits. With a ‘food first’ policy, it is increasingly recognised that projections of food needs are important for estimating future global bioenergy potential, and that non-food uses of biomass can be increased by both food crop yield improvements and dietary changes. However, few researchers have explicitly included future biomaterials production as a factor in bioenergy potential. Although biomaterials’ share of the materials market has roughly halved over the past quarter-century, we show that per tonne of biomass, biomaterials will usually allow greater greenhouse gas reductions than directly using biomass for bioenergy. particularly since in many cases, biomaterials can be later burnt for energy after their useful life.

Biomass District Energy Trigeneration Systems: Emissions Reduction and Financial Impact

International Nuclear Information System (INIS)

Rentizelas, A.; Tolis, A.; Tatsiopoulos, I.

2009-01-01

Biomass cogeneration is widely used for district heating applications in central and northern Europe. Biomass trigeneration on the other hand, constitutes an innovative renewable energy application. In this work, an approved United Nations Framework Convention on Climate Change baseline methodology has been extended to allow the examination of biomass trigeneration applications. The methodology is applied to a case study in Greece to investigate various environmental and financial aspects of this type of applications. The results suggest that trigeneration may lead to significant emissions reduction compared to using fossil fuels or even biomass cogeneration and electricity generation. The emissions reduction achieved may be materialized into a considerable revenue stream for the project, if traded through a trading mechanism such as the European Union Greenhouse Gas Emission Trading Scheme. A sensitivity analysis has been performed to compensate for the high volatility of the emission allowances' value and the immaturity of the EU Trading Scheme, which prevent a reliable estimation of the related revenue. The work concludes that emission allowances trading may develop into one of the major revenue streams of biomass trigeneration projects, significantly increasing their financial yield and attractiveness. The impact on the yield is significant even for low future values of emission allowances and could become the main income revenue source of such projects, if emission allowances increase their value substantially. The application of trigeneration for district energy proves to lead to increased environmental and financial benefits compared to the cogeneration or electricity generation cases

Thermochemical Conversion of Woody Biomass to Fuels and Chemicals Final Report

Energy Technology Data Exchange (ETDEWEB)

Pendse, Hemant P. [Univ. of Maine, Orono, ME (United States)

2015-09-30

Maine and its industries identified more efficient utilization of biomass as a critical economic development issue. In Phase I of this implementation project, a research team was assembled, research equipment was implemented and expertise was demonstrated in pyrolysis, hydrodeoxygenation of pyrolysis oils, catalyst synthesis and characterization, and reaction engineering. Phase II built upon the infrastructure to innovate reaction pathways and process engineering, and integrate new approaches for fuels and chemical production within pulp and paper and other industries within the state. This research cluster brought together chemists, engineers, physicists and students from the University of Maine, Bates College, and Bowdoin College. The project developed collaborations with Oak Ridge National Laboratory and Brookhaven National Laboratory. The specific research projects within this proposal were of critical interest to the DoE - in particular the biomass program within EERE and the catalysis/chemical transformations program within BES. Scientific and Technical Merit highlights of this project included: (1) synthesis and physical characterization of novel size-selective catalyst/supports using engineered mesoporous (1-10 nm diameter pores) materials, (2) advances in fundamental knowledge of novel support/ metal catalyst systems tailored for pyrolysis oil upgrading, (3) a microcalorimetric sensing technique, (4) improved methods for pyrolysis oil characterization, (5) production and characterization of woody biomass-derived pyrolysis oils, (6) development of two new patented bio oil pathways: thermal deoxygenation (TDO) and formate assisted pyrolysis (FASP), and (7) technoeconomics of pyrolysis of Maine forest biomass. This research cluster has provided fundamental knowledge to enable and assess pathways to thermally convert biomass to hydrocarbon fuels and chemicals.

The Prospects of Rubberwood Biomass Energy Production in Malaysia

Directory of Open Access Journals (Sweden)

Jegatheswaran Ratnasingam

2015-03-01

Full Text Available Rubber has been shown to be one of the most important plantation crops in Malaysia, and rubber tree biomass has widespread applications in almost all sectors of the wood products manufacturing sector. Despite its abundance, the exploitation of rubberwood biomass for energy generation is limited when compared to other available biomass such as oil palm, rice husk, cocoa, sugarcane, coconut, and other wood residues. Furthermore, the use of biomass for energy generation is still in its early stages in Malaysia, a nation still highly dependent on fossil fuels for energy production. The constraints for large scale biomass energy production in Malaysia are the lack of financing for such projects, the need for large investments, and the limited research and development activities in the sector of efficient biomass energy production. The relatively low cost of energy in Malaysia, through the provision of subsidy, also restricts the potential utilization of biomass for energy production. In order to fully realize the potential of biomass energy in Malaysia, the environmental cost must be factored into the cost of energy production.

Landscape ecological planning: Integrating land use and wildlife conservation for biomass crops

Energy Technology Data Exchange (ETDEWEB)

Schiller, A.

1995-12-31

What do a mussel shoat, a zoo, and a biomass plantation have in common? Each can benefit from ecology-based landscape planning. This paper provides examples of landscape ecological planning from some diverse projects the author has worked on, and discusses how processes employed and lessons learned from these projects are being used to help answer questions about the effects of biomass plantings (hardwood tree crops and native grasses) on wildlife habitat. Biomass environmental research is being designed to assess how plantings of different acreage, composition and landscape context affect wildlife habitat value, and is addressing the cumulative effect on wildlife habitat of establishing multiple biomass plantations across the landscape. Through landscape ecological planning, answers gleaned from research can also help guide biomass planting site selection and harvest strategies to improve habitat for native wildlife species within the context of economically viable plantation management - thereby integrating the needs of people with those of the environment.

Combustion Properties of Biomass Flash Pyrolysis Oils: Final Project Report

Energy Technology Data Exchange (ETDEWEB)

C. R. Shaddix; D. R. Hardesty

1999-04-01

Thermochemical pyrolysis of solid biomass feedstocks, with subsequent condensation of the pyrolysis vapors, has been investigated in the U.S. and internationally as a means of producing a liquid fuel for power production from biomass. This process produces a fuel with significantly different physical and chemical properties from traditional petroleum-based fuel oils. In addition to storage and handling difficulties with pyrolysis oils, concern exists over the ability to use this fuel effectively in different combustors. The report endeavors to place the results and conclusions from Sandia's research into the context of international efforts to utilize pyrolysis oils. As a special supplement to this report, Dr. Steven Gust, of Finland's Neste Oy, has provided a brief assessment of pyrolysis oil combustion research efforts and commercialization prospects in Europe.

Activated carbon from biomass

Science.gov (United States)

Manocha, S.; Manocha, L. M.; Joshi, Parth; Patel, Bhavesh; Dangi, Gaurav; Verma, Narendra

2013-06-01

Activated carbon are unique and versatile adsorbents having extended surface area, micro porous structure, universal adsorption effect, high adsorption capacity and high degree of surface reactivity. Activated carbons are synthesized from variety of materials. Most commonly used on a commercial scale are cellulosic based precursors such as peat, coal, lignite wood and coconut shell. Variation occurs in precursors in terms of structure and carbon content. Coir having very low bulk density and porous structure is found to be one of the valuable raw materials for the production of highly porous activated carbon and other important factor is its high carbon content. Exploration of good low cost and non conventional adsorbent may contribute to the sustainability of the environment and offer promising benefits for the commercial purpose in future. Carbonization of biomass was carried out in a horizontal muffle furnace. Both carbonization and activation were performed in inert nitrogen atmosphere in one step to enhance the surface area and to develop interconnecting porosity. The types of biomass as well as the activation conditions determine the properties and the yield of activated carbon. Activated carbon produced from biomass is cost effective as it is easily available as a waste biomass. Activated carbon produced by combination of chemical and physical activation has higher surface area of 2442 m2/gm compared to that produced by physical activation (1365 m2/gm).

Biomass briquetting and its perspectives in Brazil

International Nuclear Information System (INIS)

Felfli, Felix Fonseca; Mesa P, Juan M.; Rocha, Jose Dilcio; Filippetto, Daniele; Luengo, Carlos A.; Pippo, Walfrido Alonso

2011-01-01

A study of the status of biomass briquetting and its perspectives in Brazil was conducted including determination of the availability and characteristics of the agro-residues for briquetting. Wood residues, rice husk and coffee husk were characterized and identified as the more promising agro-residues for briquetting in the short-term in Brazil. A survey was carried out in order to determine the number of briquetting factories in Brazil, and also to determine: used briquetting technologies, briquettes production, briquettes sale prices, the status of biomass briquetting market and its future perspectives. (author)

Biomass briquetting and its perspectives in Brazil

Energy Technology Data Exchange (ETDEWEB)

Felfli, Felix Fonseca; Mesa P, Juan M. [BIOWARE Ltda., Caixa Postal 6086, 13083-970, Campinas, SP (Brazil); Rocha, Jose Dilcio [EMBRAPA-Agroenergia, Brasilia, DF (Brazil); Filippetto, Daniele; Luengo, Carlos A.; Pippo, Walfrido Alonso [Grupo Combustiveis Alternativos/Departamento de Fisica Aplicada/IFGW/UNICAMP, Caixa Postal 6165, Barao Geraldo 13083-970, Campinas, SP (Brazil)

2011-01-15

A study of the status of biomass briquetting and its perspectives in Brazil was conducted including determination of the availability and characteristics of the agro-residues for briquetting. Wood residues, rice husk and coffee husk were characterized and identified as the more promising agro-residues for briquetting in the short-term in Brazil. A survey was carried out in order to determine the number of briquetting factories in Brazil, and also to determine: used briquetting technologies, briquettes production, briquettes sale prices, the status of biomass briquetting market and its future perspectives. (author)

Supercritical Fluids Processing of Biomass to Chemicals and Fuels

Energy Technology Data Exchange (ETDEWEB)

Olson, Norman K. [Iowa State Univ., Ames, IA (United States)

2011-09-28

The main objective of this project is to develop and/or enhance cost-effective methodologies for converting biomass into a wide variety of chemicals, fuels, and products using supercritical fluids. Supercritical fluids will be used both to perform reactions of biomass to chemicals and products as well as to perform extractions/separations of bio-based chemicals from non-homogeneous mixtures. This work supports the Biomass Program’s Thermochemical Platform Goals. Supercritical fluids are a thermochemical approach to processing biomass that, while aligned with the Biomass Program’s interests in gasification and pyrolysis, offer the potential for more precise and controllable reactions. Indeed, the literature with respect to the use of water as a supercritical fluid frequently refers to “supercritical water gasification” or “supercritical water pyrolysis.”

Complex thermal energy conversion systems for efficient use of locally available biomass

International Nuclear Information System (INIS)

Kalina, Jacek

2016-01-01

This paper is focused on a theoretical study in search for new technological solutions in the field of electricity generation from biomass in small-scale distributed cogeneration systems. The purpose of this work is to draw readers' attention to possibilities of design complex multi-component hybrid and combined technological structures of energy conversion plants for effective use of locally available biomass resources. As an example, there is presented analysis of cogeneration system that consists of micro-turbine, high temperature fuel cell, inverted Bryton cycle module and biomass gasification island. The project assumes supporting use of natural gas and cooperation of the plant with a low-temperature district heating network. Thermodynamic parameters, energy conversion effectiveness and economic performance are examined. Results show relatively high energy conversion performance and on the other hand weak financial indices of investment projects at the current level of energy prices. It is however possible under certain conditions to define an optimistic business model that leads to a feasible project. - Highlights: • Concept of biomass energy conversion plant is proposed and theoretically analysed. • MCFC type fuel cell is fuelled with biomass gasification gas. • Natural gas fired microturbine is considered as a source of continuous power. • Inverted Bryton Cycle is considered for utilisation of high temperature exhaust gas.

2nd generation lignocellulosic bioethanol: is torrefaction a possible approach to biomass pretreatment?

Energy Technology Data Exchange (ETDEWEB)

Chiaramonti, David; Rizzo, Andrea Maria; Prussi, Matteo [University of Florence, CREAR - Research Centre for Renewable Energy and RE-CORD, Florence (Italy); Tedeschi, Silvana; Zimbardi, Francesco; Braccio, Giacobbe; Viola, Egidio [ENEA - Laboratory of Technology and Equipment for Bioenergy and Solar Thermal, Rotondella (Italy); Pardelli, Paolo Taddei [Spike Renewables s.r.l., Florence (Italy)

2011-03-15

Biomass pretreatement is a key and energy-consuming step for lignocellulosic ethanol production; it is largely responsible for the energy efficiency and economic sustainability of the process. A new approach to biomass pretreatment for the lignocellulosic bioethanol chain could be mild torrefaction. Among other effects, biomass torrefaction improves the grindability of fibrous materials, thus reducing energy demand for grinding the feedstock before hydrolysis, and opens the biomass structure, making this more accessible to enzymes for hydrolysis. The aim of the preliminary experiments carried out was to achieve a first understanding of the possibility to combine torrefaction and hydrolysis for lignocellulosic bioethanol processes, and to evaluate it in terms of sugar and ethanol yields. In addition, the possibility of hydrolyzing the torrefied biomass has not yet been proven. Biomass from olive pruning has been torrefied at different conditions, namely 180-280 C for 60-120 min, grinded and then used as substrate in hydrolysis experiments. The bioconversion has been carried out at flask scale using a mixture of cellulosolytic, hemicellulosolitic, {beta}-glucosidase enzymes, and a commercial strain of Saccharomyces cerevisiae. The experiments demonstrated that torrefied biomass can be enzymatically hydrolyzed and fermented into ethanol, with yields comparable with grinded untreated biomass and saving electrical energy. The comparison between the bioconversion yields achieved using only raw grinded biomass or torrefied and grinded biomass highlighted that: (1) mild torrefaction conditions limit sugar degradation to 5-10%; and (2) torrefied biomass does not lead to enzymatic and fermentation inhibition. Energy consumption for ethanol production has been preliminary estimated, and three different pretreatment steps, i.e., raw biomass grinding, biomass-torrefaction grinding, and steam explosion were compared. Based on preliminary results, steam explosion still has a

Biomass estimation with high resolution satellite images: A case study of Quercus rotundifolia

Science.gov (United States)

Sousa, Adélia M. O.; Gonçalves, Ana Cristina; Mesquita, Paulo; Marques da Silva, José R.

2015-03-01

Forest biomass has had a growing importance in the world economy as a global strategic reserve, due to applications in bioenergy, bioproduct development and issues related to reducing greenhouse gas emissions. Current techniques used for forest inventory are usually time consuming and expensive. Thus, there is an urgent need to develop reliable, low cost methods that can be used for forest biomass estimation and monitoring. This study uses new techniques to process high spatial resolution satellite images (0.70 m) in order to assess and monitor forest biomass. Multi-resolution segmentation method and object oriented classification are used to obtain the area of tree canopy horizontal projection for Quercus rotundifolia. Forest inventory allows for calculation of tree and canopy horizontal projection and biomass, the latter with allometric functions. The two data sets are used to develop linear functions to assess above ground biomass, with crown horizontal projection as an independent variable. The functions for the cumulative values, both for inventory and satellite data, for a prediction error equal or smaller than the Portuguese national forest inventory (7%), correspond to stand areas of 0.5 ha, which include most of the Q.rotundifolia stands.

YEAR 2 BIOMASS UTILIZATION

Energy Technology Data Exchange (ETDEWEB)

Christopher J. Zygarlicke

2004-11-01

This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

Advancing Commercialization of Algal Biofuel through Increased Biomass Productivity and Technical Integration

Energy Technology Data Exchange (ETDEWEB)

Anton, David [Cellana, LLC, Kailua-Kona, HI (United States)

2016-12-31

The proposed project built on the foundation of over several years years of intensive and ground-breaking R&D work at Cellana's Kona Demonstration Facility (KDF). Phycological and engineering solutions were provided to tackle key cultivation issues and technical barriers limiting algal biomass productivity identified through work conducted outdoors at industrial (1 acre) scale. The objectives of this project were to significantly improve algal biomass productivity and reduce operational cost in a seawater-based system, using results obtained from two top-performing algal strains as the baseline while technically advancing and more importantly, integrating the various unit operations involved in algal biomass production, processing, and refining.

Pressurised combustion of biomass-derived, low calorific value, fuel gas

Energy Technology Data Exchange (ETDEWEB)

Andries, J; Hoppesteyn, P D.J.; Hein, K R.G. [Lab. for Thermal Power Engineering, Dept. of Mechanical Engineering and Marine Technology, Delft Univ. of Technology (Netherlands)

1997-12-31

The Laboratory for Thermal Power Engineering of the Delft University of Technology is participating in an EU-funded, international R + D project which is designed to aid European industry in addressing issues regarding pressurised combustion of biomass-derived, low calorific flue fuel gas. The objects of the project are: To design, manufacture and test a pressurised, high temperature gas turbine combustor for biomass derived LCV fuel gas; to develop a steady-state and dynamic model describing a combustor using biomass-derived, low calorific value fuel gases; to gather reliable experimental data on the steady-state and dynamic characteristics of the combustor; to study the steady-state and dynamic plant behaviour using a plant layout wich incorporates a model of a gas turbine suitable for operation on low calorific value fuel gas. (orig)

Pressurised combustion of biomass-derived, low calorific value, fuel gas

Energy Technology Data Exchange (ETDEWEB)

Andries, J.; Hoppesteyn, P.D.J.; Hein, K.R.G. [Lab. for Thermal Power Engineering, Dept. of Mechanical Engineering and Marine Technology, Delft Univ. of Technology (Netherlands)

1996-12-31

The Laboratory for Thermal Power Engineering of the Delft University of Technology is participating in an EU-funded, international R + D project which is designed to aid European industry in addressing issues regarding pressurised combustion of biomass-derived, low calorific flue fuel gas. The objects of the project are: To design, manufacture and test a pressurised, high temperature gas turbine combustor for biomass derived LCV fuel gas; to develop a steady-state and dynamic model describing a combustor using biomass-derived, low calorific value fuel gases; to gather reliable experimental data on the steady-state and dynamic characteristics of the combustor; to study the steady-state and dynamic plant behaviour using a plant layout wich incorporates a model of a gas turbine suitable for operation on low calorific value fuel gas. (orig)

Guideline for safe and eco-friendly biomass gasification

Energy Technology Data Exchange (ETDEWEB)

Vos, J.; Knoef, H. (BTG biomass technology group, Enschede (Netherlands)); Hauth, M. (Graz Univ. of Technology. Institute of Thermal Engineering, Graz (Austria)) (and others)

2009-11-15

The objective of the Gasification Guide project is to accelerate the market penetration of small-scale biomass gasification systems (< 5 MW fuel power) by the development of a Guideline and Software Tool to facilitate risk assessment of HSE aspects. The Guideline may also be applied in retrofitting or converting old thermal plants in the Eastern European countries - with rich biomass recourses - to new gasification plants. The objective of this document is to guide key target groups identifying potential hazards and make a proper risk assessment. The software tool is an additional aid in the risk assessment. This guideline is intended to be a training tool and a resource for workers and employers to safely design, fabricate, construct, operate and maintain small-scale biomass gasification facilities. The Guideline is applicable with the following constraints: 1) The maximum scale of the gasification plant was agreed to be about 1 MW{sub e}. The reason is that large companies do have normally their safety rules in place; 2) This means in principle only fixed bed gasifier designs. However, most parts are also valid to other designs and even other thermal conversion processes; 3) The use of contaminated biomass is beyond the scope of this Guideline. The Guideline contains five major chapters; Chapter 2 briefly describes the gasification technology in general. Chapter 3 gives an overview of major legal framework issues on plant permission and operation. The legal frame is changing and the description is based on the situation by the end of 2007. Chapter 4 explains the theory behind the risk assessment method and risk reduction measures. Chapter 5 is the heart of the Guideline and gives practical examples of good design, operation and maintenance principles. The practical examples and feedback have been received throughout the project and the description is based on mid-2009. Chapter 6 describes the best techniques currently available for emission abatement which are

Interactions between crop biomass and development of foliar diseases in winter wheat and the potential to graduate the fungicide dose according to crop biomass

DEFF Research Database (Denmark)

Jensen, Peter Kryger; Jørgensen, Lise Nistrup

2016-01-01

dose. The study was carried out investigating fungicide dose response controlling foliar diseases in winter wheat at three biomass densities obtained growing the crop at three nitrogen levels and using variable seed rates. Further the field experiments included three fungicide dose rates at each...... biomass level, an untreated control, and 75%, 50% and 33% of the recommended fungicide dose rate and the experiments were replicated for three years. Crop biomass had a significant influence on occurrence of septoria and yellow rust with greater disease severity at increasing crop biomass. In two of three...... years, the interaction of crop biomass and fungicide dose rate had a significant influence on disease severity indicating a biomassdependent dose response. The interaction occurred in the two years with high yield potential in combination with severe disease attack. If the variation in crop density...

Temporal species richness-biomass relationships along successional gradients

Science.gov (United States)

Guo, Q.

2003-01-01

Diversity-biomass relationships are frequently reported to be hump-shaped over space at a given time. However, it is not yet clear how diversity and biomass change simultaneously and how they are related to each other over time (e.g. in succession) at one locality. This study develops a temporal model based on the projected changes of various community variables in a generalized terrestrial environment after fire and uses post-fire succession data on Santa Monica Mountains of southern California and other published succession data to examine the temporal diversity-biomass relationships. The results indicate that in the early stages of succession, both diversity and biomass increase and a positive relationship appears, while in the late stages of succession, biomass continued to increase but diversity usually declines; thus a negative relationship may be observed. When the scales of measurement become sufficiently large so that the measured diversity and biomass cross various stages of succession, a 'hump-shaped' relationship can emerge. The diversity-biomass relationship appears to be concordant in space and time when appropriate scales are used. Formerly proposed explanations for spatial patterns may well apply to the temporal patterns (particularly colonization, facilitation and competitive exclusion).

Regulation of bacterioplankton density and biomass in tropical shallow coastal lagoons

Directory of Open Access Journals (Sweden)

Fabiana MacCord

Full Text Available AIM: Estimating bacterioplankton density and biomass and their regulating factors is important in order to evaluate aquatic systems' carrying capacity, regarding bacterial growth and the stock of matter in the bacterial community, which can be consumed by higher trophic levels. We aim to evaluate the limnological factors which regulate - in space and time - the bacterioplankton dynamics (abundance and biomass in five tropical coastal lagoons in the state of Rio de Janeiro, Brazil. METHOD: The current study was carried out at the following lagoons: Imboassica, Cabiúnas, Comprida, Carapebus and Garças. They differ in morphology and in their main limnological factors. The limnological variables as well as bacterioplankton abundance and biomass were monthly sampled for 14 months. Model selection analyses were performed in order to evaluate the main variables regulating the bacterioplankton's dynamics in these lagoons. RESULT: The salt concentration and the "space" factor (i.e. different lagoons explained great part of the bacterial density and biomass variance in the studied tropical coastal lagoons. When the lagoons were analyzed separately, salinity still explained great part of the variation of bacterial density and biomass in the Imboassica and Garças lagoons. On the other hand, phosphorus concentration was the main factor explaining the variance of bacterial density and biomass in the distrophic Cabiúnas, Comprida and Carapebus lagoons. There was a strong correlation between bacterial density and biomass (r² = 0.70, p < 0.05, indicating that bacterial biomass variations are highly dependent on bacterial density variations. CONCLUSION: (i Different limnological variables regulate the bacterial density and biomass in the studied coastal lagoons, (ii salt and phosphorus concentrations greatly explained the variation of bacterial density and biomass in the saline and distrophic lagoons, respectively, and (iii N-nitrate and chlorophyll

Biomass power industry: Assessment of key players and approaches for DOE and industry interaction

International Nuclear Information System (INIS)

1993-01-01

This report reviews the status of the US biomass power industry. The topics of the report include current fuels and the problems associated with procuring, transporting, preparing and burning them, competition from natural gas projects because of the current depressed natural gas prices, need for incentives for biomass fueled projects, economics, market potential and expansion of US firms overseas

Progress on Optimizing Miscanthus Biomass Production for the European Bioeconomy: Results of the EU FP7 Project OPTIMISC.

Science.gov (United States)

Lewandowski, Iris; Clifton-Brown, John; Trindade, Luisa M; van der Linden, Gerard C; Schwarz, Kai-Uwe; Müller-Sämann, Karl; Anisimov, Alexander; Chen, C-L; Dolstra, Oene; Donnison, Iain S; Farrar, Kerrie; Fonteyne, Simon; Harding, Graham; Hastings, Astley; Huxley, Laurie M; Iqbal, Yasir; Khokhlov, Nikolay; Kiesel, Andreas; Lootens, Peter; Meyer, Heike; Mos, Michal; Muylle, Hilde; Nunn, Chris; Özgüven, Mensure; Roldán-Ruiz, Isabel; Schüle, Heinrich; Tarakanov, Ivan; van der Weijde, Tim; Wagner, Moritz; Xi, Qingguo; Kalinina, Olena

2016-01-01

This paper describes the complete findings of the EU-funded research project OPTIMISC, which investigated methods to optimize the production and use of miscanthus biomass. Miscanthus bioenergy and bioproduct chains were investigated by trialing 15 diverse germplasm types in a range of climatic and soil environments across central Europe, Ukraine, Russia, and China. The abiotic stress tolerances of a wider panel of 100 germplasm types to drought, salinity, and low temperatures were measured in the laboratory and a field trial in Belgium. A small selection of germplasm types was evaluated for performance in grasslands on marginal sites in Germany and the UK. The growth traits underlying biomass yield and quality were measured to improve regional estimates of feedstock availability. Several potential high-value bioproducts were identified. The combined results provide recommendations to policymakers, growers and industry. The major technical advances in miscanthus production achieved by OPTIMISC include: (1) demonstration that novel hybrids can out-yield the standard commercially grown genotype Miscanthus x giganteus; (2) characterization of the interactions of physiological growth responses with environmental variation within and between sites; (3) quantification of biomass-quality-relevant traits; (4) abiotic stress tolerances of miscanthus genotypes; (5) selections suitable for production on marginal land; (6) field establishment methods for seeds using plugs; (7) evaluation of harvesting methods; and (8) quantification of energy used in densification (pellet) technologies with a range of hybrids with differences in stem wall properties. End-user needs were addressed by demonstrating the potential of optimizing miscanthus biomass composition for the production of ethanol and biogas as well as for combustion. The costs and life-cycle assessment of seven miscanthus-based value chains, including small- and large-scale heat and power, ethanol, biogas, and insulation

Biogenic methane from hydrothermal gasification of biomass; Biogenes Methan durch hydrothermale Vergasung von Biomasse

Energy Technology Data Exchange (ETDEWEB)

Schubert, M.; Vogel, F.

2007-09-15

This final report for the Swiss Federal Office of Energy (SFOE) reports on work done in the area of gasification of biomass. The use of dung, manure and sewage sludge as sources of energy is described and discussed. Hydrothermal gasification is proposed as an alternative to conventional gas-phase processes. The aim of the project in this respect is discussed. Here, a catalytic process that demonstrates the gasification of wet biomass to synthetic natural gas (SNG) in a continuously operating plant on a laboratory scale is being looked at. Difficulties encountered in preliminary tests are discussed. Long-term catalyst stability and the installations for the demonstration of the process are discussed, and gasification tests with ethanol are commented on.

Availability of waste and biomass for energy generation in the Netherlands. Summary of the report GAVE-9911 and EWAB-9926; Beschikbaarheid van afval en biomassa voor energieopwekking in Nederland. Samenvatting GAVE-9911 -- EWAB-9926

Energy Technology Data Exchange (ETDEWEB)

Weterings, R.A.P.M.; Koppejan, J. [TNO Milieu, Energie- en Processinnovatie TNO-MEP, Apeldoorn (Netherlands); Bergsma, G.C. [Centrum voor Energiebesparing en schone technologie CE, Delft (Netherlands); Meeusen-van Onna, M.J.G. [Landbouw Economisch Instituut LEI, Den Haag (Netherlands)

1999-12-01

The Netherlands agency for energy and the environment (Novem) commissioned a consortium to carry out the ABC (Dutch abbreviation for Waste and Biomass Conversion) project in three separate studies: (A) a scenario study of the availability of biomass and waste for energy generation in the Netherlands; (B) a 'three-level assessment' of biomass availability on national, European and global levels; and (C) a scenario study of the feasibility / profitability of energy crops in the Netherlands. The results of the ABC project are published in two separate reports. This present report gives the results of the combined scenario study of availability (A) and the three-level assessment (B). The results of the energy crops study (C) are presented elsewhere. The goal of the present project is to gain insight into the current availability of biomass and waste flows for energy generation, and of the driving forces and constraints that can affect their availability up to the year 2020. First, it is examined whether the availability of biomass and waste is or could become problematic. This is an important aspect for market parties that want to invest in energy from biomass and biomass. Second, it is examined what additional policy measures the Dutch government would need to take to achieve the set policy goal of savings of fossil fuels. The combined scenario study of waste availability (in the Netherlands) and biomass availability (in the Netherlands, the European Union, and worldwide) for energy generation started off with a Definition Phase. In this phase, the project's framework and key issues were formulated and relevant sources of information were outlined. On the basis of these sources, a Quick Scan was carried out to map the existing information as well as any gaps in knowledge and uncertainties about the availability of biomass and waste. In the subsequent In-depth Phase the results of the Quick Scan were submitted to a number of national experts for comment

Evaluation of herbacceous biomass crops in the northern Great Plains. Final report

Energy Technology Data Exchange (ETDEWEB)

Meyer, D.W.; Norby, W.E.; Erickson, D.O.; Johnson, R.G. [North Dakota State Univ., Fargo, ND (United States)

1994-08-01

Herbaceous lignocellulose crops are a potential renewable feedstock for biochemical conversion systems second in size to wood products. Several herbaceous crops are utilized as forage crops in the northern Great Plains, but forage quality considerations usually dictates a early harvest. Biomass cropping does not have this constraint; therefore, little information was available on herbaceous crops utilized as energy crops prior to this project. Our primary objectives were to evaluate the biomass yield and select chemical components of several herbaceous crops for energy crops in the northern Great Plains, compare the economic feasibility of energy crops with common competing crops, and evaluate biomass cropping on summer fallow lands. Three good, two marginal, and one irrigated sites were used during 1988 to 1992 for the first component. At least six perennial and four annual biomass species were included at all sites. Three to four nitrogen (N) levels and a crop-recrop comparison (annuals only) were management intensities included. Biomass cropping on idled lands was performed on dryland at Carrington and evaluated the effects of removing leguminous biomass on fallowed lands. This report summarizes results from the 5-year project.

Environmental impact of woody biomass use in Botswana - the case of fuelwood

International Nuclear Information System (INIS)

Sekhwela, M.B.M.

1997-01-01

A review of fuelwood and deforestation in Botswana is presented. Details are given of the AFREPREN biomass research project to evaluate the methods for examining biomass energy sources in Botswana and Rwanda, and the contribution of fuelwood harvesting to deforestation. (UK)

Biomass market introduction. How to overcome the non-technical barriers for a wider use of biomass gasification in Europe. Proceedings of a workshop. Utrecht, November 28. 1997

International Nuclear Information System (INIS)

Kaltschmitt, M.; Kwant, K.W.

1998-03-01

Bioenergy projects can fail due to technical problems but also due to non-technical barriers. The authors mention the risk of failure, the biomass supply assurance, financing, uncertainty about emission regulations, and acceptance by the public. On the above mentioned background a workshop was organised at 28 November 1997, as a joint activity of Novem and the EU / FAIR Concerted Action Analysis and Co-ordination of the Activities concerning a Gasification of Biomass'. At this workshop important non-technical barriers are identified, ways how to overcome them are analyzed, defined and actions are discussed to be taken on the EU and National level to improve the implementation of biomass gasification projects. Copies of overhead sheets and texts of 14 papers are presented

LIGNOCELLULOSIC BIOMASS AFTER EXPLOSIVE AUTOHYDROLYSIS AS SUBSTRATE TO BUTANOL OBTAINING

Directory of Open Access Journals (Sweden)

Tigunova

2016-08-01

Full Text Available The aim of the work was investigation of the effect of the explosive autohydrolysis on lignocellulosic biomass (saving, switchgrass biomass for consequent use as a substrate to produce biofuels such as butanol. Butanol-producing strains, switchgrass Panicum virgatum L. biomass and its components after autohydrolysis were used in study. The thermobaric pressure pretreatment of lignocellulosic biomass was carried out using specially designed equipment. The effect of explosive autohydrolysis on lignocellulosic biomass for further use in producing biofuels using microbial conversion was studied. Components of lignocellulosic biomass were fractionated after undergoing thermobaric treatment. The possibility of using different raw material components after using explosive autohydrolysis processing to produce biobutanol was found. Products of switchgrass biomass autohydrolysis were shown to need further purification before fermentation from furfural formed by thermobaric pretreatment and inhibiting the growth of microorganisms. The ability of strains of the genus Clostridium to use cellulose as a substrate for fermentation was proved. It was found that using explosive autohydrolysis pretreatment to savings allowed boosting the butanol accumulation by 2 times.

Hydrothermal carbonisation of biomass. Results and perspectives; Hydrothermale Carbonisierung von Biomasse. Ergebnisse und Perspektiven

Energy Technology Data Exchange (ETDEWEB)

Grimm, Christiane (ed.)

2013-06-01

Due to the ambitious political targets for the utilization of renewable energy in the energy supply, climate protection and resource conservation, biomass gained increasing attention. With the aim of developing new and more efficient ways of recycling organic waste, the Federal Foundation for the Environment (Osnabrueck, Federal Republic of Germany) supports funding projects for the technological development of the hydrothermal carbonization with respect to the optimization of reaction processes and targeted production of certain qualities of biochar. The results of the funded projects of Federal Foundation for the Environment are presented in this conference proceedings.

Forest biomass observation: current state and prospective

Directory of Open Access Journals (Sweden)

D. G. Schepaschenko

2017-08-01

Full Text Available With this article, we provide an overview of the methods, instruments and initiatives for forest biomass observation at global scale. We focus on the freely available information, provided by both remote and in-situ observations. The advantages and limitation of various space borne methods, including optical, radar (C, L and P band and LiDAR, as well as respective instruments available on the orbit (MODIS, Proba-V, Landsat, Sentinel-1, Sentinel-2 , ALOS PALSAR, Envisat ASAR or expecting (BIOMASS, GEDI, NISAR, SAOCOM-CS are discussed. We emphasize the role of in-situ methods in the development of a biomass models, providing calibration and validation of remote sensing data. We focus on freely available forest biomass maps, databases and empirical models. We describe the functionality of Biomass.Geo-Wiki.org portal, which provides access to a collection of global and regional biomass maps in full resolution with unified legend and units overplayed with high-resolution imagery. The Forest-Observation-System.net is announced as an international cooperation to establish a global in-situ forest biomass database to support earth observation and to encourage investment in relevant field-based observations and science. Prospects of unmanned aerial vehicles in the forest inventory are briefly discussed. The work was partly supported by ESA IFBN project (contract 4000114425/15/NL/FF/gp.

Impact of future tax incentive legislation on the development of biomass energy

International Nuclear Information System (INIS)

Middleton, G.L. Jr.

1991-01-01

Historically, the use of biomass as an energy source has been subsidized by generous tax incentives. These tax incentives took the form of tax-exempt financing, the energy tax credit, the investment tax credit, and short depreciation lives. Common with tax incentives in other areas, the tax incentives for biomass projects have been curtailed in recent years. Given the appetite of Congress for revenue, it is not likely that the recent trend will reverse. If changes do occur, they are likely to involve liberalization of some oof the rules for tax-exempt debt. But even under current law, there are still tax advantages available for biomass energy projects, of which potential developers should be aware

Strategic analysis of biomass and waste fuels for electric power generation

International Nuclear Information System (INIS)

Wiltsee, G.A. Jr.; Easterly, J.; Vence, T.

1993-12-01

In this report, the Electric Power Research Institute (EPRI) intends to help utility companies evaluate biomass and wastes for power generation. These fuels may be alternatives or supplements to fossil fuels in three applications: (1) utility boiler coining; (2) dedicated combustion/energy recovery plants; and 3) dedicated gasification/combined cycle plants. The report summarizes data on biomass and waste properties, and evaluates the cost and performance of fuel preparation and power generation technologies. The primary biomass and waste resources evaluated are: (1) wood wastes (from forests, mills, construction/demolition, and orchards) and short rotation woody crops; (2) agricultural wastes (from fields, animals, and processing) and herbaceous energy crops; and (3) consumer or industrial wastes (e.g., municipal solid waste, scrap tires, sewage sludge, auto shredder waste). The major fuel types studied in detail are wood, municipal solid waste, and scrap tires. The key products of the project include the BIOPOWER model of biomass/waste-fired power plant performance and cost. Key conclusions of the evaluation are: (1) significant biomass and waste fuel resources are available; (2) biomass power technology cannot currently compete with natural gas-fired combined cycle technology; (3) coining biomass and waste fuels with coal in utility and industrial boilers is the most efficient, lowest cost, and lowest risk method of energy recovery from residual materials; (4) better biomass and waste fuel production and conversion technology must be developed, with the help of coordinated government energy and environmental policies and incentives; and (5) community partnerships can enhance the chances for success of a project

Gasification and co-gasification of biomass wastes: Effect of the biomass origin and the gasifier operating conditions

Energy Technology Data Exchange (ETDEWEB)

Lapuerta, Magin; Hernandez, Juan J.; Pazo, Amparo; Lopez, Julio [Universidad de Castilla-La Mancha, Escuela Tecnica Superior de Ingenieros Industriales (Edificio Politecnico), Avenida Camilo Jose Cela s/n. 13071 Ciudad Real (Spain)

2008-09-15

Air gasification of different biomass fuels, including forestry (pinus pinaster pruning) and agricultural (grapevine and olive tree pruning) wastes as well as industry wastes (sawdust and marc of grape), has been carried out in a circulating flow gasifier in order to evaluate the potential of using these types of biomass in the same equipment, thus providing higher operation flexibility and minimizing the effect of seasonal fuel supply variations. The potential of using biomass as an additional supporting fuel in coal fuelled power plants has also been evaluated through tests involving mixtures of biomass and coal-coke, the coke being a typical waste of oil companies. The effect of the main gasifier operating conditions, such as the relative biomass/air ratio and the reaction temperature, has been analysed to establish the conditions allowing higher gasification efficiency, carbon conversion and/or fuel constituents (CO, H{sub 2} and CH{sub 4}) concentration and production. Results of the work encourage the combined use of the different biomass fuels without significant modifications in the installation, although agricultural wastes (grapevine and olive pruning) could to lead to more efficient gasification processes. These latter wastes appear as interesting fuels to generate a producer gas to be used in internal combustion engines or gas turbines (high gasification efficiency and gas yield), while sawdust could be a very adequate fuel to produce a H{sub 2}-rich gas (with interest for fuel cells) due to its highest reactivity. The influence of the reaction temperature on the gasification characteristics was not as significant as that of the biomass/air ratio, although the H{sub 2} concentration increased with increasing temperature. (author)

The EU Emissions Trading Scheme and Biomass. Final Report

International Nuclear Information System (INIS)

Schwaiger, H.; Tuerk, A.; Arasto, A.; Vehlow, J.; Kautto, N.; Sijm, J.; Hunder, M.; Brammer, J.

2009-02-01

Within its Energy and Climate Package, adopted by the European Parliament in December 2008, the European commission set a 10% minimum for the market share of renewables in the transport sector in 2020. To find the appropriate instruments to reach this target and the instrument mix with which biomass use in general could be best stimulated are the main questions of this project. An important instrument of the European Climate Policy is the European Emissions Trading Scheme (EU-ETS), which started operation in 2005. Previous work done within Bioenergy NoE showed that only a high share of auctioning of allowances and a high CO2 price provide necessary incentives for a higher biomass use. According to the Energy and Climate Package, all allowances will be auctioned in the energy sector from 2013 on, with exceptions for a few CEE countries. Based on work done within the project, a model has been developed to analyse at which CO2 price biomass becomes competitive in case of 100 per cent auctioning or at a lower level. The European Commission furthermore decided not to include the road transport sector into the EU-ETS until 2020. Whether the inclusion of the road transport sector in the EU-ETS, could help introducing biofuels, a separate trading scheme for biofuels should be set up, or biofuels should be addressed with other policy instruments, was another main question of this project. The first result shows that an integrated scheme would hardly have any effects on the use of liquid biofuels in the transportation sector, but might cause higher CO2 prices for the energy and industry sector. A separate trading scheme has been implemented in the UK in 2008, California is planning such as scheme in addition to include the road transport sector into the future ETS. Within this project the design of such as system has been elaborated based on the comparison of several policy instruments to increase the use of liquid biofuels in the transportation sector. Policy interaction

Co pyrolysis of biomass and PP

International Nuclear Information System (INIS)

Heo, Hyeon Su; Kim, Jung Hwan; Cho, Hye Jung; Ko, Jeong Huy; Park, Hye Jin; Bae, Yoon Ju; Park, Young Kwon

2010-01-01

Full text: While bio-oil has received considerable attention both as a source of energy and as an organic feedstock, its stability as fuel is very low due to high oxygen content. Therefore, there are many efforts to upgrade it. Among them, co pyrolysis with polyolefin can be a method to obtain stable bio-oil. Because polyolefins contain higher hydrogen and carbon content than biomass and no oxygen, plastic/ biomass co pyrolysis may upgrade the bio-oil properties by increasing the carbon and hydrogen contents while reducing oxygen content. In this study, wood biomass was mixed with PP and then co pyrolysis was carried out in a batch reactor. The produced oil and gas was analyzed using GC and GC-MS. Also elemental analysis was performed to know the hydrogen, carbon and oxygen content of bio-oil. The effect of various reaction conditions on bio-oil properties were presented in detail. (author)

First Biomass Conference of the Americas: Energy, environment, agriculture, and industry. Proceedings, Volume 2

Energy Technology Data Exchange (ETDEWEB)

1993-10-01

This conference was designed to provide a national and international forum to support the development of a viable biomass industry. Although papers on research activities and technologies under development that address industry problems comprised part of this conference, an effort was made to focus on scale-up and demonstration projects, technology transfer to end users, and commercial applications of biomass and wastes. The conference was divided into these major subject areas: Resource Base, Power Production, Transportation Fuels, Chemicals and Products, Environmental Issues, Commercializing Biomass Projects, Biomass Energy System Studies, and Biomass in Latin America. The papers in this second volume cover Transportation Fuels, and Chemicals and Products. Transportation Fuels topics include: Biodiesel, Pyrolytic Liquids, Ethanol, Methanol and Ethers, and Commercialization. The Chemicals and Products section includes specific topics in: Research, Technology Transfer, and Commercial Systems. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Biomass energy in Central America

Energy Technology Data Exchange (ETDEWEB)

Blanco, J M [Biomass Users` Network, Regional Office for Central America and the Caribbean, San Jose (Costa Rica)

1995-12-01

The objective of this paper is to introduce the concept of biomass to energy issues and opportunities in Central America. In this region, made up of seven countries (Belize, Costa Rica, El Salvador, Guatemala, Honduras, Nicaragua and Panama), the biomass sector has the potential to play a crucial role in alleviating the environmental and development predicaments faced by all economies of the region. This paper assesses the available biomass resources at the regional and country levels and gives an overview of the current utilization of biomass fuels. It also describes the overall context in which the biomass-to-energy initiatives are immersed. At the regional level, biomass energy consumption accounts for more than 50% of total energy consumption. In regard to the utilization of biomass for energy purposes, it is clear that Central America faces a critical juncture at two levels, both mainly in rural areas: in the productive sector and at the household level. The absence of sustainable development policies and practices has jeopardized the availability of biomass fuels, particularly wood. Firewood is an important source of energy for rural industries such as coffee processing, which is one of the largest productive activities in the region. This paper comments on some of the most successful technological innovations already in place in the region, for instance, the rapid development of co-generation projects by the sugar cane industry, especially in El Salvador and Guatemala, the substitution of coffee husks for firewood in coffee processing plants in Costa Rica and El Salvador and the sustainable use of pine forests for co-generation in Honduras. Only one out of every two inhabitants in Central America now has access to electricity from the public grid. Biomass fuels, mainly firewood but also, to a lesser extent, other crop residues such as corn stalks, are the main source of energy for cooking and heating by most of the population. (It is foreseen that by the end

Biomass energy in Central America

International Nuclear Information System (INIS)

Blanco, J.M.

1995-01-01

The objective of this paper is to introduce the concept of biomass to energy issues and opportunities in Central America. In this region, made up of seven countries (Belize, Costa Rica, El Salvador, Guatemala, Honduras, Nicaragua and Panama), the biomass sector has the potential to play a crucial role in alleviating the environmental and development predicaments faced by all economies of the region. This paper assesses the available biomass resources at the regional and country levels and gives an overview of the current utilization of biomass fuels. It also describes the overall context in which the biomass-to-energy initiatives are immersed. At the regional level, biomass energy consumption accounts for more than 50% of total energy consumption. In regard to the utilization of biomass for energy purposes, it is clear that Central America faces a critical juncture at two levels, both mainly in rural areas: in the productive sector and at the household level. The absence of sustainable development policies and practices has jeopardized the availability of biomass fuels, particularly wood. Firewood is an important source of energy for rural industries such as coffee processing, which is one of the largest productive activities in the region. This paper comments on some of the most successful technological innovations already in place in the region, for instance, the rapid development of co-generation projects by the sugar cane industry, especially in El Salvador and Guatemala, the substitution of coffee husks for firewood in coffee processing plants in Costa Rica and El Salvador and the sustainable use of pine forests for co-generation in Honduras. Only one out of every two inhabitants in Central America now has access to electricity from the public grid. Biomass fuels, mainly firewood but also, to a lesser extent, other crop residues such as corn stalks, are the main source of energy for cooking and heating by most of the population. (It is foreseen that by the end

Alkali deposits found in biomass boilers: The behavior of inorganic material in biomass-fired power boilers -- Field and laboratory experiences. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Baxter, L.L. [Sandia National Labs., Livermore, CA (United States). Combustion Research Facility; Miles, T.R.; Miles, T.R. Jr. [Miles (Thomas R.), Portland, OR (United States); Jenkins, B.M. [California Univ., Davis, CA (United States); Dayton, D.C.; Milne, T.A. [National Renewable Energy Lab., Golden, CO (United States); Bryers, R.W. [Foster Wheeler Development Corp., Livingston, NJ (United States); Oden, L.L. [Bureau of Mines, Albany, OR (United States). Albany Research Center

1996-03-01

This report documents the major findings of the Alkali Deposits Investigation, a collaborative effort to understand the causes of unmanageable ash deposits in biomass-fired electric power boilers. Volume 1 of this report provide an overview of the project, with selected highlights. This volume provides more detail and discussion of the data and implications. This document includes six sections. The first, the introduction, provides the motivation, context, and focus for the investigation. The remaining sections discuss fuel properties, bench-scale combustion tests, a framework for considering ash deposition processes, pilot-scale tests of biomass fuels, and field tests in commercially operating biomass power generation stations. Detailed chemical analyses of eleven biomass fuels representing a broad cross-section of commercially available fuels reveal their properties that relate to ash deposition tendencies. The fuels fall into three broad categories: (1) straws and grasses (herbaceous materials); (2) pits, shells, hulls and other agricultural byproducts of a generally ligneous nature; and (3) woods and waste fuels of commercial interest. This report presents a systematic and reasonably detailed analysis of fuel property, operating condition, and boiler design issues that dictate ash deposit formation and property development. The span of investigations from bench-top experiments to commercial operation and observations including both practical illustrations and theoretical background provide a self-consistent and reasonably robust basis to understand the qualitative nature of ash deposit formation in biomass boilers. While there remain many quantitative details to be pursued, this project encapsulates essentially all of the conceptual aspects of the issue. It provides a basis for understanding and potentially resolving the technical and environmental issues associated with ash deposition during biomass combustion. 81 refs., 124 figs., 76 tabs.

Biomass gasifier projects for decentralized power supply in India: A financial evaluation

International Nuclear Information System (INIS)

Nouni, M.R.; Mullick, S.C.; Kandpal, T.C.

2007-01-01

Results of a techno-economic evaluation of biomass gasifier based projects for decentralized power supply for remote locations in India are presented. Contributions of different components of diesel engine generator (DG) sets, dual fuel (DF) engine generator sets and 100% producer gas (HPG) engine generator sets to their capital costs as well as to the levelized unit cost of electricity (LUCE) delivered by the same have been analyzed. LUCE delivered to the consumers has been estimated to be varying in the range of Rs. 13.14-24.49/kWh (US$ 0.30-0.55/kWh) for DF BGPP. LUCE increases significantly if BGPP is operated at part loads. Presently available 40kW capacity HPG systems in India are expected to be financially competitive with a DG set of equivalent capacity beyond a break-even diesel price of Rs. 34.70/l. It is expected to be financially more attractive than an equivalent capacity DF BGPP for diesel prices of more than Rs. 44.29/l. In certain specific conditions operating two smaller capacity systems has been found to be attractive as against a single larger capacity system

Overview of biomass and waste fuel resources for power production

International Nuclear Information System (INIS)

Easterly, J.L.; Burnham, M.

1993-01-01

This paper provides an overview of issues and opportunities associated with the use of biomass for electric power generation. Important physical characteristics of biomass and waste fuels are summarized, including comparisons with conventional fossil fuels, primarily coal. The paper also provides an overview of the current use of biomass and waste fuels for electric power generation. Biomass and waste fuels are currently used for approximately 9,800 megawatts (MW) of electric generating capacity, including about 6,100 MW of capacity fueled by wood/wood waste and about 2,200 MW of capacity fueled with municipal solid waste. Perspectives on the future availability of biomass fuels (including energy crops) are addressed, as well as projected levels of market penetration for biomass power. By the year 2010, there is a potential for 22,000 MW, to as much as 70,000 MW of biomass-powered electric generating capacity in the U.S. Given the range of benefits offered by biomass, including reduced sulfur emissions, reduced greenhouse gas emissions, job creation, rural revitalization impacts, and new incentives under the Energy Policy Act of 1992, the potential use of biomass for power production could significantly expand in the future

Pyrolysis kinetics investigation of Malaysian based biomass with non-isothermal thermogravimetric analysis (TGA)

International Nuclear Information System (INIS)

Seyed Shahabeddin Nehzati; Dayang Radiah Awang Biak; Wan Azlina Wan Abdul Karim Ghani; Mohd Amran Mohd Salleh

2010-01-01

Full text: Biomass is currently being used as a sustainable energy source. Otherwise the scarceness of fossil fuel sources and the demand for environmental responsibility force the industries to use biomass as an alternate source of energy. Pyrolysis is the first step of biomass conversion and well understanding of this process can develop the biomass conversion such as gasification, liquefaction, carbonization and combustion .TGA studies of Malaysian based biomass have been carried out. TGA studies provide important insight on the thermochemical behavior of specific solid waste. The results of non-isothermal thermogravimetric analysis of palm kernel shell, coconut shell and bagasse, carried out at heating rates of 10 degree Celsius/ min, 20 degree Celsius/ min and 50 degree Celsius/ min, to ramp the temperature from 30 to 1000 were analysed. The TGA studies were carried out in an inert atmosphere of nitrogen. Arrhenius parameters were estimated by 3 different models namely Kissinger model, three-pseudo component and DEAM model the estimated values and the models were compared. The results show that the three-pseudo component model has a good agreement with the experimental results, indicating that ligno celluloses components in the mixture behave in the same way as they do separately. Also it is seen that the decomposition process shifts to higher temperatures at higher heating rates as a result of the competing effects of heat and mass transfer to the material. (Author)

From research plots to prototype biomass plantations

Energy Technology Data Exchange (ETDEWEB)

Kenney, W.A.; Vanstone, B.J.; Gambles, R.L.; Zsuffa, L. [Univ. of Toronto, Ontario (Canada)

1993-12-31

The development of biomass energy plantations is now expanding from the research plot phase into the next level of development at larger scale plantings. This is necessary to provide: more accurate information on biomass yields, realistic production cost figures, venues to test harvesting equipment, demonstration sites for potential producers, and a supply of feedstock for prototype conversion facilities. The paper will discuss some of these objectives and some of the challenges encountered in the scale-up process associated with a willow prototype plantation project currently under development in Eastern Canada.

Biomass thermochemical conversion program: 1987 annual report

Energy Technology Data Exchange (ETDEWEB)

Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

1988-01-01

The objective of the Biomass Thermochemical Conversion Program is to generate a base of scientific data and conversion process information that will lead to establishment of cost-effective processes for conversion of biomass resources into clean fuels. To accomplish this objective, in fiscal year 1987 the Thermochemical Conversion Program sponsored research activities in the following four areas: Liquid Hydrocarbon Fuels Technology; Gasification Technology; Direct Combustion Technology; Program Support Activities. In this report an overview of the Thermochemical Conversion Program is presented. Specific research projects are then described. Major accomplishments for 1987 are summarized.

Fundamental Study of Single Biomass Particle Combustion

DEFF Research Database (Denmark)

Momenikouchaksaraei, Maryam

This thesis is a comprehensive study of single biomass particle combustion. The effect of particle shape and size and operating conditions on biomass conversion characteristics were investigated experimentally and theoretically. The experimental samples were divided in two groups: particles...... well-defined conditions, and the complete combustion processes were recorded as video sequences by a CCD camera installed in the set-up. One of the project objectives is to simulate conditions reasonably close to the conditions in a power plant boiler, i.e., reasonably high temperatures (up to 1600°C...

Biomass power. Exploring the diffusion challenges in Spain

International Nuclear Information System (INIS)

Dinica, Valentina

2009-01-01

The use of biomass resources for power generation offers numerous benefits of interest for political decision-makers: fuel security, rural and industrial development, ecological benefits. In Spain, policy instruments have been used since 1980 to stimulate biomass power generation. However, the diffusion outcome by 2007 was very disappointing: only 525 MW. This paper argues that two factors lie at the core of this: the conceptualization of biomass resources by political decision-makers in the instruments used, and the desire that policy instruments be in line with market liberalization principles. These generated a persistent economic obstacle for biomass power generation, and impeded the development of markets for the supply of biomass resources. The policy learning regarding the heterogeneity of biomass resources, and the investors' expectations on risks, profitability and resource markets was very slow among political decision-makers. The paper contributes to the understanding of diffusion outcomes by proposing to analyse diffusion by means of five indicators: types of resources, technologies, developers, motivations to invest and project sizes. Besides, the paper shows the usefulness of investigating policy instruments in terms of their risk and profitability characteristics. This enables a better understanding of the diffusion patterns and outcomes. (author)

Bioenergy Research Programme. Yearbook 1997. Utilization of bioenergy and biomass conversion

International Nuclear Information System (INIS)

Nikku, P.

1998-01-01

The aim of the research programme is to increase the use of economically profitable and environmentally sound bioenergy, by improving the competitiveness of present peat and wood fuels. Research and development projects will also develop new economically competitive biofuels, new equipment and methods for production, handling and using of biofuels. The total funding for 1997 was 33.5 million FIM, and the number of projects 62. The number of projects concerning bioenergy use was 17 and biomass conversion 4. Results from the projects that were going on in 1997 are presented in this publication. The aim of the bioenergy use is to develop and demonstrate at least 3-4 new equipment or methods for handling and use of biofuels. The equipment and/or methods should provide economically competitive and environmentally sound energy production. The second aim is to demonstrate at least 2-3 large-scale biofuel end-use technologies. Each of these should have a potential of 0.2-0.3 million toe per year till the year 2000. The aims have been achieved in the field of fuel handling technologies and small scale combustion concepts, but the large scale demonstration projects before the year 2000 seem to be a very challenging goal. The aim of the biomass conversion is to produce basic information on biomass conversion, to evaluate the quality of products, their usability, environmental effects of the use as well as the total economy of the production. The objective of the biomass conversion is to develop 2-3 new methods, which could be demonstrated, for the production and utilization of liquefied, gasified and other converted biofuels. The production target is 0.2-0.3 million toe per year by 2005 at a competitive price level. The studies focused on the development of flash pyrolysis technology for biomass, and on the study of the storage stability of imported wood oils and their suitability for use in oil-fired boilers and diesel power plants

First Biomass Conference of the Americas: Energy, environment, agriculture, and industry; Proceedings, Volume 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-10-01

This conference was designed to provide a national and international forum to support the development of a viable biomass industry. Although papers on research activities and technologies under development that address industry problems comprised part of this conference, an effort was made to focus on scale-up and demonstration projects, technology transfer to end users, and commercial applications of biomass and wastes. The conference was divided into these major subject areas: Resource Base, Power Production, Transportation Fuels, Chemicals and Products, Environmental Issues, Commercializing Biomass Projects, Biomass Energy System Studies, and Biomass in Latin America. The papers in this first volume deal with Resource Base and Power Production. The particular subjects within the Resource Base area are Biomass, Wastes and Residues, Feedstock Research, and Commercial Systems. The emphasized subjects within the Power Production area are Combustion, Thermal and Biological Gasification, Waste Generation and Waste Disposal and Waste Emissions, and Heat, Steam, and Fuels-Commercial Systems. Selected abstracts have been indexed separately for inclusion in the Energy Science and Technology Database.

Combining woody biomass for combustion with green waste composting: Effect of removal of woody biomass on compost quality.

Science.gov (United States)

Vandecasteele, Bart; Boogaerts, Christophe; Vandaele, Elke

2016-12-01

The question was tackled on how the green waste compost industry can optimally apply the available biomass resources for producing both bioenergy by combustion of the woody fraction, and high quality soil improvers as renewable sources of carbon and nutrients. Compost trials with removal of woody biomass before or after composting were run at 9 compost facilities during 3 seasons to include seasonal variability of feedstock. The project focused on the changes in feedstock and the effect on the end product characteristics (both compost and recovered woody biomass) of this woody biomass removal. The season of collection during the year clearly affected the biochemical and chemical characteristics of feedstock, woody biomass and compost. On one hand the effect of removal of the woody fraction before composting did not significantly affect compost quality when compared to the scenario where the woody biomass was sieved from the compost at the end of the composting process. On the other hand, quality of the woody biomass was not strongly affected by extraction before or after composting. The holocellulose:lignin ratio was used in this study as an indicator for (a) the decomposition potential of the feedstock mixture and (b) to assess the stability of the composts at the end of the process. Higher microbial activity in green waste composts (indicated by higher oxygen consumption) and thus a lower compost stability resulted in higher N immobilization in the compost. Removal of woody biomass from the green waste before composting did not negatively affect the compost quality when more intensive composting was applied. The effect of removal of the woody fraction on the characteristics of the green waste feedstock and the extracted woody biomass is depending on the season of collection. Copyright © 2016 Elsevier Ltd. All rights reserved.

Wood, straw, energetic crops... Biomass energy. A sustainable alternative for your projects

International Nuclear Information System (INIS)

2007-01-01

After having briefly recalled the French and European legal context promoting the use of renewable energies, this document highlights the challenges associated with such a development. They concern the environment, the energetic independence, the cost of energy, and the local and rural development. It evokes the actions and labels which favour the improvement and the renewal of domestic heating equipment, the large number of installations using biomass for collective heating or for industrial heating. It indicates the objectives of the biomass energy programme for 2007-2010, and describes the French energy conservation agency (ADEME) role and missions within this programme

S2Biom database with logistical components of the biomass value chain

NARCIS (Netherlands)

Annevelink, E.; Groot, de H.L.E.; Shah, N.; Giarola, S.; Pantaleo, M.; Anttila, P.; Vis, Martijn; Raa, te Rik; Berg, van den Douwe; Gabrielle, B.

2015-01-01

The S2Biom project (www.s2biom.eu) - Delivery of sustainable supply of non-food biomass to support
a resource-efficient Bioeconomy in Europe - supports sustainable delivery chains of non-food biomass feedstock.
This poses a logistical challenge because the quality and handling

Torrefaction of biomass for power production

DEFF Research Database (Denmark)

Saleh, Suriyati Binti

In order to increase the share of biomass for sustainable energy production, it will be an advantage to utilize fuels as straw, wood and waste on large suspension fired boilers. On a European scale, currently large straw resources are available that are not fully utilized for energy production...... rates, relatively low superheater temperatures have to be applied, which in turn lower the power efficiency. The idea for this Ph.D. project is to develop a biomass pretreatment method that could provide the heating value of the fuel for the boiler, but in a way such that the fuel is easily pulverized.......D. thesis focus on the following subjects: 1) the development of experimental procedures for a novel laboratory scale reactor (simultaneous torrefaction and grinding) and a study on the torrefaction of straw and wood; 2) study the influence of biomass chemical properties such as ash content, ash composition...

Aboveground biomass subdivisions in woody species of the savanna ecosystem project study area, Nylsvley

CSIR Research Space (South Africa)

Rutherford, MC

1979-01-01

Full Text Available Aboveground peak season biomass is given for 11 woody species in each of five belt transects under study. Mean aerial biomass for all species was 16 273 kg ha, made up of 14 937 kg ha wood, 236 kg ha current season's twigs and 1 100 kg ha leaves...

Woody biomass utilization trends, barriers, and strategies: Perspectives of U.S. Forest Service managers

Science.gov (United States)

Shiloh Sundstrom; Max Nielsen-Pincus; Cassandra Moseley; Sarah. McCaffrey

2012-01-01

The use of woody biomass is being promoted across the United States as a means of increasing energy independence, mitigating climate change, and reducing the cost of hazardous fuels reduction treatments and forest restoration projects. The opportunities and challenges for woody biomass use on the national forest system are unique. In addition to making woody biomass...

Production costs for SRIC Populus biomass

International Nuclear Information System (INIS)

Strauss, C.H.

1991-01-01

Production costs for short rotation, intensive culture (SRIC) Populus biomass were developed from commercial-sized plantations under investigation throughout the US. Populus hybrid planted on good quality agricultural sites at a density of 850 cuttings/acre was projected to yield an average of 7 ovendry (OD) tons/acre/year. Discounted cash-flow analysis of multiple rotations showed preharvest production costs of $14/ton (OD). Harvesting and transportation expenses would increase the delivered cost to $35/ton (OD). Although this total cost compared favorably with the regional market price for aspen (Populus tremuloides), future investments in SRIC systems will require the development of biomass energy markets

Progress on Optimizing Miscanthus Biomass Production for the European Bioeconomy: Results of the EU FP7 Project OPTIMISC

Science.gov (United States)

Lewandowski, Iris; Clifton-Brown, John; Trindade, Luisa M.; van der Linden, Gerard C.; Schwarz, Kai-Uwe; Müller-Sämann, Karl; Anisimov, Alexander; Chen, C.-L.; Dolstra, Oene; Donnison, Iain S.; Farrar, Kerrie; Fonteyne, Simon; Harding, Graham; Hastings, Astley; Huxley, Laurie M.; Iqbal, Yasir; Khokhlov, Nikolay; Kiesel, Andreas; Lootens, Peter; Meyer, Heike; Mos, Michal; Muylle, Hilde; Nunn, Chris; Özgüven, Mensure; Roldán-Ruiz, Isabel; Schüle, Heinrich; Tarakanov, Ivan; van der Weijde, Tim; Wagner, Moritz; Xi, Qingguo; Kalinina, Olena

2016-01-01

This paper describes the complete findings of the EU-funded research project OPTIMISC, which investigated methods to optimize the production and use of miscanthus biomass. Miscanthus bioenergy and bioproduct chains were investigated by trialing 15 diverse germplasm types in a range of climatic and soil environments across central Europe, Ukraine, Russia, and China. The abiotic stress tolerances of a wider panel of 100 germplasm types to drought, salinity, and low temperatures were measured in the laboratory and a field trial in Belgium. A small selection of germplasm types was evaluated for performance in grasslands on marginal sites in Germany and the UK. The growth traits underlying biomass yield and quality were measured to improve regional estimates of feedstock availability. Several potential high-value bioproducts were identified. The combined results provide recommendations to policymakers, growers and industry. The major technical advances in miscanthus production achieved by OPTIMISC include: (1) demonstration that novel hybrids can out-yield the standard commercially grown genotype Miscanthus x giganteus; (2) characterization of the interactions of physiological growth responses with environmental variation within and between sites; (3) quantification of biomass-quality-relevant traits; (4) abiotic stress tolerances of miscanthus genotypes; (5) selections suitable for production on marginal land; (6) field establishment methods for seeds using plugs; (7) evaluation of harvesting methods; and (8) quantification of energy used in densification (pellet) technologies with a range of hybrids with differences in stem wall properties. End-user needs were addressed by demonstrating the potential of optimizing miscanthus biomass composition for the production of ethanol and biogas as well as for combustion. The costs and life-cycle assessment of seven miscanthus-based value chains, including small- and large-scale heat and power, ethanol, biogas, and insulation

Progress on optimizing miscanthus biomass production for the European bioeconomy: Results of the EU FP7 project OPTIMISC

Directory of Open Access Journals (Sweden)

Iris Lewandowski

2016-11-01

Full Text Available This paper describes the complete findings of the EU-funded research project OPTIMISC, which investigated methods to optimize the production and use of miscanthus biomass. Miscanthus bioenergy and bioproduct chains were investigated by trialing fifteen diverse germplasm types in a range of climatic and soil environments across central Europe, Ukraine, Russia and China. The abiotic stress tolerances of a wider panel of 100 germplasm types to drought, salinity and low temperatures were measured in the laboratory and a field trial in Belgium. A small selection of germplasm types was evaluated for performance in grasslands on marginal sites in Germany and the UK. The growth traits underlying biomass yield and quality were measured to improve regional estimates of feedstock availability. Several potential high-value bioproducts were identified. The combined results provide recommendations to policymakers, growers and industry. The major technical advances in miscanthus production achieved by OPTIMISC include: 1 demonstration that novel hybrids can out-yield the standard commercially grown genotype Miscanthus x giganteus; 2 characterisation of the interactions of physiological growth responses with environmental variation within and between sites; 3 quantification of biomass-quality-relevant traits; 4 abiotic stress tolerances of miscanthus genotypes; 5 selections suitable for production on marginal land; 6 field establishment methods for seeds using plugs; 7 evaluation of harvesting methods; and 8 quantification of energy used in densification (pellet technologies with a range of hybrids with differences in stem wall properties. End-user needs were addressed by demonstrating the potential of optimizing miscanthus biomass composition for the production of ethanol and biogas as well as for combustion. The costs and life-cycle assessment of seven miscanthus-based value chains, including small- and large-scale heat and power, ethanol, biogas and

Lorraine - The beautiful biomass energy

International Nuclear Information System (INIS)

Braun, Pascale

2013-01-01

This article evokes various projects of biomass energy production which have been recently developed and built in north-eastern France, notably for industrial and heating applications. It also outlines that the largest industrial projects have been given up: because of the relative steadiness of gas and coal prices, and of the possible opportunity given by shale gas exploitation, industries have been reluctant in investing installations which take longer time to be written off. The quantities of yearly available wood have been reduced for different reasons: resource accessibility, landscape preservation, vicinity of water harnessing points. These restrictions entailed the definition of threshold for the public support of new projects, a decision with which industrials disagree

The study of reactions influencing the biomass steam gasification process

Energy Technology Data Exchange (ETDEWEB)

C. Franco; F. Pinto; I. Gulyurtlu; I. Cabrita [INETI-DEECA, Lisbon (Portugal)

2003-05-01

Steam gasification studies were carried out in an atmospheric fluidised bed. The gasifier was operated over a temperature range of 700 900{sup o}C whilst varying a steam/biomass ratio from 0.4 to 0.85 w/w. Three types of forestry biomass were studied: Pinus pinaster (softwood), Eucalyptus globulus and holm-oak (hardwood). The energy conversion, gas composition, higher heating value and gas yields were determined and correlated with temperature, steam/biomass ratio, and species of biomass used. The results obtained seemed to suggest that the operating conditions were optimised for a gasification temperature around 830{sup o}C and a steam/biomass ratio of 0.6 0.7 w/w, because a gas richer in hydrogen and poorer in hydrocarbons and tars was produced. These conditions also favoured greater energy and carbon conversions, as well the gas yield. The main objective of the present work was to determine what reactions were dominant within the operation limits of experimental parameters studied and what was the effect of biomass type on the gasification process. As biomass wastes usually have a problem of availability because of seasonal variations, this work analysed the possibility of replacing one biomass species by another, without altering the gas quality obtained. 19 refs., 8 figs. 2 tabs.

Enhancing Cellulase Commercial Performance for the Lignocellulosic Biomass Industry

Energy Technology Data Exchange (ETDEWEB)

Jarnigan, Alisha [Danisco, US Inc., Copenhagen (Denmark)

2016-06-07

Cellulase enzyme loading (Bt-G) for the economic conversion of lignocellulosic biomass to ethanol is on of the key challenges identified in the Biomass Program of DOE/EERE. The goal of Danisco’s project which ran from 2008 to 2012, was to address the technical challenge by creating more efficient enzyme that could be used at lower doses, thus reducing the enzymes’ cost contribution to the conversio process. We took the approach of protein engineering of cellulase enzymes to overcome the enzymati limitations in the system of cellulosic-hydrolyzing enzymes to improve performance in conversion o biomass, thereby creating a more effective enzyme mix.

Physico-chemical characterisation of Indian biomass ashes

Energy Technology Data Exchange (ETDEWEB)

K. Umamaheswaran; Vidya S. Batra [Energy and Resources Institute (TERI), New Delhi (India)

2008-05-15

India stands fourth in biomass utilisation for various purposes like domestic, commercial and industrial applications. While extensive studies have been made for coal ash characterisation and utilisation, studies on characterisation of biomass ash and its utilisation has not been addressed. In this paper, biomass ash from five sources i.e. rice husk, bagasse, groundnut shell, cashewnut shell, and arecanut shell have been characterised. Chemical composition analysis, particle size analysis, thermal analysis, and microstructure analysis were carried out. Results show that in all ashes silica is the major compound with particle size ranging from 15 to 30 {mu}m and having irregular shape. Ash powders originating from cashewnut shell, arecanut shell and groundnut shell also have compounds of calcium, magnesium and potassium. Bagasse and cashewnut shell ashes have high LOI due to presence of unburnt carbon, P{sub 2}O{sub 5} and other volatiles. 16 refs., 22 figs., 3 tabs.

Biofluid process: fluidised-bed gasification of biomass

Energy Technology Data Exchange (ETDEWEB)

Dittrich, A. [ATEKO a.s., Hradec Kralove (Czech Republic)

1996-12-31

Fluidised-bed gasification of biomass was developed by ATEKO by using long-term experience from coal gasification. An experimental unit was built and a number of tests, first with sawdust gasification, were carried out. A gas combustion engine combined with a power generator was installed and operated in power production. (orig.)

Biofluid process: fluidised-bed gasification of biomass

Energy Technology Data Exchange (ETDEWEB)

Dittrich, A [ATEKO a.s., Hradec Kralove (Czech Republic)

1997-12-31

Fluidised-bed gasification of biomass was developed by ATEKO by using long-term experience from coal gasification. An experimental unit was built and a number of tests, first with sawdust gasification, were carried out. A gas combustion engine combined with a power generator was installed and operated in power production. (orig.)

Biomass Business Opportunities Viet Nam

Energy Technology Data Exchange (ETDEWEB)

Zwebe, D [SNV Netherlands Development Organisation, Ha Noi (Viet Nam)

2012-03-15

The goal of this survey is to provide a more specific and integral perspective in which niches, relevant policy development by the Vietnamese government, legislation and sustainability criteria are clearly addressed to benefit both the Dutch Private sector as well as to stimulate Dutch-Vietnamese cooperation and support the Vietnamese government in its search for tangible options to develop the desired enabling environment for a sustainable biomass/biofuel market. The following activities are defined to be executed to reach the goal of the project: Biomass availability in Vietnam (Chapter 2); Government of Vietnam and Energy (Chapter 3); The opportunities and barriers to enter the market in Vietnam (Chapter 4 and 5); Stakeholder analysis of the bio-energy sector (Chapter 6); and Recommendations (Chapter 7)

Accurate inference of shoot biomass from high-throughput images of cereal plants

Directory of Open Access Journals (Sweden)

Tester Mark

2011-02-01

Full Text Available Abstract With the establishment of advanced technology facilities for high throughput plant phenotyping, the problem of estimating plant biomass of individual plants from their two dimensional images is becoming increasingly important. The approach predominantly cited in literature is to estimate the biomass of a plant as a linear function of the projected shoot area of plants in the images. However, the estimation error from this model, which is solely a function of projected shoot area, is large, prohibiting accurate estimation of the biomass of plants, particularly for the salt-stressed plants. In this paper, we propose a method based on plant specific weight for improving the accuracy of the linear model and reducing the estimation bias (the difference between actual shoot dry weight and the value of the shoot dry weight estimated with a predictive model. For the proposed method in this study, we modeled the plant shoot dry weight as a function of plant area and plant age. The data used for developing our model and comparing the results with the linear model were collected from a completely randomized block design experiment. A total of 320 plants from two bread wheat varieties were grown in a supported hydroponics system in a greenhouse. The plants were exposed to two levels of hydroponic salt treatments (NaCl at 0 and 100 mM for 6 weeks. Five harvests were carried out. Each time 64 randomly selected plants were imaged and then harvested to measure the shoot fresh weight and shoot dry weight. The results of statistical analysis showed that with our proposed method, most of the observed variance can be explained, and moreover only a small difference between actual and estimated shoot dry weight was obtained. The low estimation bias indicates that our proposed method can be used to estimate biomass of individual plants regardless of what variety the plant is and what salt treatment has been applied. We validated this model on an independent

Inventory of the possibilities to process biomass using the existing industrial infrastructure

International Nuclear Information System (INIS)

Van Aart, F.J.J.M.; Barkhuysen, K.

1999-07-01

In the Netherlands, the government has formulated objectives for stimulating the use of sustainable energy and reducing CO 2 emissions. The replacement of fossil fuels by biomass is a major cornerstone of this policy. This has already resulted in a number of study projects, experiments and, in some cases, implementation projects in the co-fuelling of biomass in pulverised coal- or gas-fired power stations. Since the total energy use in the Netherlands depends only in part on power stations, it is still the question whether the total potential for the application of biomass in the Netherlands is being utilised. In order to study this question, Novem commissioned KEMA to make an inventory of the possibilities of processing biomass in industry via the existing infrastructure. The most important umbrella organisations, interest groups, sector organisations and leading companies have been approached in order to obtain insight into the potential of using biomass, and the willingness to do so. The following sectors of industry were selected: foodstuffs and luxury foods, chemicals, building materials, basic metals, metal products, glass and the fodder drying industry. In the cement industry and in the fodder drying industry, there is interest and there exist possibilities for using biomass as an alternative to fossil fuels in the existing industrial processes. The recommendation is to study in greater detail the feasibility of using biomass in the fodder drying industry. In the other sectors of industry which were investigated, there appeared to be little opportunity to use biomass in industrial processes. 4 refs

Biomass production from the U.S. forest and agriculture sectors in support of a renewable electricity standard

International Nuclear Information System (INIS)

White, Eric M.; Latta, Greg; Alig, Ralph J.; Skog, Kenneth E.; Adams, Darius M.

2013-01-01

Production of renewable energy from biomass has been promoted as means to improve greenhouse gas balance in energy production, improve energy security, and provide jobs and income. However, uncertainties remain as to how the agriculture and forest sectors might jointly respond to increased demand for bioelectricity feedstocks and the potential environmental consequences of increased biomass production. We use an economic model to examine how the agriculture and forest sectors might combine to respond to increased demands for bioelectricity under simulated future national-level renewable electricity standards. Both sectors are projected to contribute biomass, although energy crops, like switchgrass, produced on agriculture land are projected to be the primary feedstocks. At the highest targets for bioelectricity production, we project increased conversion of forest to agriculture land in support of agriculture biomass production. Although land conversion takes place in response to renewable electricity mandates, we project only minor increases in forest and agriculture emissions. Similarly, crop prices were projected to generally be stable in the face of increased bioelectricity demand and displacement of traditional agriculture crops. - Highlights: ► We model the response of forest and agriculture to increased bioelectricity demand. ► The agriculture sector, through energy crop production, is the key biomass provider. ► Increased land exchange is projected for the highest bioelectricity demands. ► Land exchange from forest to agriculture yield the greatest changes in GHG flux. ► Agriculture and forestry must be accounted for when considering bioenergy policy

Economic, energy and environmental evaluations of biomass-based fuel ethanol projects based on life cycle assessment and simulation

International Nuclear Information System (INIS)

Yu Suiran; Tao Jing

2009-01-01

This paper summarizes the research of Monte Carlo simulation-based Economic, Energy and Environmental (3E) Life Cycle Assessment (LCA) of the three Biomass-based Fuel Ethanol (BFE) projects in China. Our research includes both theoretical study and case study. In the theoretical study part, 3E LCA models are structured, 3E Index Functions are defined and the Monte Carlo simulation is introduced to address uncertainties in BFE life cycle analysis. In the case study part, projects of Wheat-based Fuel Ethanol (WFE) in Central China, Corn-based Fuel Ethanol (CFE) in Northeast China, and Cassava-based Fuel Ethanol (CFE) in Southwest China are evaluated from the aspects of economic viability and investment risks, energy efficiency and airborne emissions. The life cycle economy assessment shows that KFE project in Guangxi is viable, while CFE and WFE projects are not without government's subsidies. Energy efficiency assessment results show that WFE, CFE and KFE projects all have positive Net Energy Values. Emissions results show that the corn-based E10 (a blend of 10% gasoline and 90% ethanol by volume), wheat-based E10 and cassava-base E10 have less CO 2 and VOC life cycle emissions than conventional gasoline, but wheat-based E10 and cassava-based E10 can generate more emissions of CO, CH 4 , N 2 O, NO x , SO 2 , PM 10 and corn-based E10 can has more emissions of CH 4 , N 2 O, NO x , SO, PM 10 .

Acid-functionalized nanoparticles for biomass hydrolysis

Science.gov (United States)

Pena Duque, Leidy Eugenia

Cellulosic ethanol is a renewable source of energy. Lignocellulosic biomass is a complex material composed mainly of cellulose, hemicellulose, and lignin. Biomass pretreatment is a required step to make sugar polymers liable to hydrolysis. Mineral acids are commonly used for biomass pretreatment. Using acid catalysts that can be recovered and reused could make the process economically more attractive. The overall goal of this dissertation is the development of a recyclable nanocatalyst for the hydrolysis of biomass sugars. Cobalt iron oxide nanoparticles (CoFe2O4) were synthesized to provide a magnetic core that could be separated from reaction using a magnetic field and modified to carry acid functional groups. X-ray diffraction (XRD) confirmed the crystal structure was that of cobalt spinel ferrite. CoFe2O4 were covered with silica which served as linker for the acid functions. Silica-coated nanoparticles were functionalized with three different acid functions: perfluoropropyl-sulfonic acid, carboxylic acid, and propyl-sulfonic acid. Transmission electron microscope (TEM) images were analyzed to obtain particle size distributions of the nanoparticles. Total carbon, nitrogen, and sulfur were quantified using an elemental analyzer. Fourier transform infra-red spectra confirmed the presence of sulfonic and carboxylic acid functions and ion-exchange titrations accounted for the total amount of catalytic acid sites per nanoparticle mass. These nanoparticles were evaluated for their performance to hydrolyze the beta-1,4 glycosidic bond of the cellobiose molecule. Propyl-sulfonic (PS) and perfluoropropyl-sulfonic (PFS) acid functionalized nanoparticles catalyzed the hydrolysis of cellobiose significantly better than the control. PS and PFS were also evaluated for their capacity to solubilize wheat straw hemicelluloses and performed better than the control. Although PFS nanoparticles were stronger acid catalysts, the acid functions leached out of the nanoparticle during

Literature Review of Physical and Chemical Pretreatment Processes for Lignocellulosic Biomass

Energy Technology Data Exchange (ETDEWEB)

Harmsen, P.; Bakker, R. [Wageningen University and Research centre WUR, Food and Biobased Research WUR-FBR, Wageningen (Netherlands); Huijgen, W.J.J. [ECN Biomass, Coal and Environment, Petten (Netherlands); Bermudez Lopez, L. [Abengoa Bioenergia Nuevas Tecnologias ABNT (Spain)

2010-09-15

This literature review was performed within the BioSynergy project (2007-2010). BioSynergy is a European Integrated Project supported through the Sixth Framework Programme for Research and Technological Development (038994-SES6). BioSynergy stands for 'BIOmass for the market competitive and environmentally friendly SYNthesis of bio-products together with the production of secondary enERGY carriers through the biorefinery approach'. Within the BioSynergy project the overall goal of the pretreatment routes being developed is to convert raw lignocellulosic biomass into its composing sugars and lignin in a market competitive and environmentally sustainable way. This report reviews lignocellulose pretreatment in general as well as specific pretreatment technologies that are developed within the BioSynergy project including steam explosion (ABNT), mechanical/alkaline fractionation (WUR) and organosolv fractionation (ECN). In addition to these pretreatment technologies, other pretreatment technologies are studied within the BioSynergy project such as acetic/formic acid pretreatment and mild- and strong acid pretreatment.

Biomass power for rural development. Quarterly report, July 3--December 4, 1997

Energy Technology Data Exchange (ETDEWEB)

Cooper, J.T.

1998-03-01

This paper describes progress in several projects related to biomass power. These include switchgrass conversion development; switchgrass gasification development; production activities including soil studies, carbon studies, switchgrass production economics, watershed impacts, and prairie lands bio-products; information and education; and geographical information system. Attachments describe switchgrass co-firing test; switchgrass production in Iowa; cooperative agreements with ISU; Rathbun Lake watershed project; newspaper articles and information publications; Secretary of Agriculture Glickman`s visit; integration of technical aspects of switchgrass production in Iowa; and evaluation of an integrated biomass gasification/fuel cell power plant.

Recipe-based co-HTL of biomass and organic waste

DEFF Research Database (Denmark)

Toor, Saqib Sohail; Rosendahl, Lasse Aistrup; Sintamarean, Iulia-Maria

2018-01-01

Hydrothermal liquefaction (HTL) has been investigated for several decades as a means to convert a wide range of biomasses and residues efficiently and with high yield into biofuel intermediates. As a wet processing technology, HTL is generally carried out in aqueous media of at least 50%–60% water...... making it very suitable for most natural biomasses and organic residues [1–4]. Processed at temperatures around 280–370°C, even up to approximately 400°C, and pressures between 10 and 30 MPa, the original biomass breaks down into a bio-crude phase (typically the main and desired product), an aqueous...... phase with water-soluble organics, and minor fractions of solid residue and gas. The yield and composition of these products depends not only on reactor type, process conditions, and product workup but also to a very large extent on the biochemical composition of the biomass. Over the past few years...

Biomass. A promising option for renewable energy in the built environment

International Nuclear Information System (INIS)

Koppejan, J.

1999-01-01

A brief overview is given of activities of local governments (municipalities and provinces) in the Netherlands with respect to the use of biomass for the production of energy in urban areas. Special attention is paid to a project in Apeldoorn, Netherlands, where biomass gasification at a waste recycling plant ('Veluwse Afvalrecycling' or VAR) is used for district heating purposes. 1 ref

Biomass as a fuel and a profitable investment: the Euro-ASEAN COGEN program

International Nuclear Information System (INIS)

Menu, J.-F.; Schenkel, Y.; Guillaume, M.

1997-01-01

The COGEN Program (''Cogen'') is an economic cooperation program between the European Commission and ASEAN (Association of Southeast Asian Nations). A pioneering initiative in the field of biomass energy. Cogen is coordinated by and from AIT (Asian Institute of Technology, Bangkok, Thailand). Its main objective is to accelerate the implementation of proven technologies generating heat and/or power from wood and agro-residues through partnerships between European and ASEAN companies. ASEAN now offers the biggest potential for energy solutions, including waste-based fuels. Within Cogen, a number of demonstration projects have been implemented in different ASEAN industries. These projects have generated over 100 million US dollars in direct investment and represent showcases of proven technology in biomass energy equipment around the region. Some biomass energy projects have been highly profitable. The success of Cogen can also be explained by an emphasis on market intelligence, i.e., information sources, channels and business opportunities rarely achieved in public-private initiatives. (author)

Systems Based Approaches for Thermochemical Conversion of Biomass to Bioenergy and Bioproducts

Energy Technology Data Exchange (ETDEWEB)

Taylor, Steven [Auburn Univ., AL (United States)

2016-07-11

Auburn’s Center for Bioenergy and Bioproducts conducts research on production of synthesis gas for use in power generation and the production of liquid fuels. The overall goal of our gasification research is to identify optimal processes for producing clean syngas to use in production of fuels and chemicals from underutilized agricultural and forest biomass feedstocks. This project focused on construction and commissioning of a bubbling-bed fluidized-bed gasifier and subsequent shakedown of the gasification and gas cleanup system. The result of this project is a fully commissioned gasification laboratory that is conducting testing on agricultural and forest biomass. Initial tests on forest biomass have served as the foundation for follow-up studies on gasification under a more extensive range of temperatures, pressures, and oxidant conditions. The laboratory gasification system consists of a biomass storage tank capable of holding up to 6 tons of biomass; a biomass feeding system, with loss-in-weight metering system, capable of feeding biomass at pressures up to 650 psig; a bubbling-bed fluidized-bed gasification reactor capable of operating at pressures up to 650 psig and temperatures of 1500oF with biomass flowrates of 80 lb/hr and syngas production rates of 37 scfm; a warm-gas filtration system; fixed bed reactors for gas conditioning; and a final quench cooling system and activated carbon filtration system for gas conditioning prior to routing to Fischer-Tropsch reactors, or storage, or venting. This completed laboratory enables research to help develop economically feasible technologies for production of biomass-derived synthesis gases that will be used for clean, renewable power generation and for production of liquid transportation fuels. Moreover, this research program provides the infrastructure to educate the next generation of engineers and scientists needed to implement these technologies.

Biomass shock pretreatment

Science.gov (United States)

Holtzapple, Mark T.; Madison, Maxine Jones; Ramirez, Rocio Sierra; Deimund, Mark A.; Falls, Matthew; Dunkelman, John J.

2014-07-01

Methods and apparatus for treating biomass that may include introducing a biomass to a chamber; exposing the biomass in the chamber to a shock event to produce a shocked biomass; and transferring the shocked biomass from the chamber. In some aspects, the method may include pretreating the biomass with a chemical before introducing the biomass to the chamber and/or after transferring shocked biomass from the chamber.

Enhancing biomass energy use in Kenya

International Nuclear Information System (INIS)

Banwell, P.S.; Harriss, R.C.

1992-01-01

This paper argues that in Kenya, environmental and economic factors will favour the continued use of biomass as a primary fuel for household an institutional cooking for the next decade or longer. The paper describes several successful projects which have improved the efficiency of urban charcoal use and of rural woodfuel use. The Kenya Ceramic Jiko, a more efficient version of the traditional charcoal stove, is a model programme sustained by free market competition, artisans participation, and widespread public acceptance. The Maendeleo stove is the best example of a successful rural woodstove project. The performance attributes of the stove, and its promotion through Kenya's largest women's organization, have resulted int he distribution of an estimated 26,000 Maendeleo stoves. Rural stove efficiency will become important as the cash-based economy expands in those areas. Agroforestry will also be critical to an enhanced use of biomass energy in Kenya. Experience to date shows that successful agroforestry programmes will have to be appropriate to local conditions and crops. (author). 25 refs, 2 figs, 3 tabs

Environmental and socioeconomic aspects in the strategic analysis of a biomass power plant integration

International Nuclear Information System (INIS)

Varela, M.; Lechon, Y.; Saez, R.

1999-01-01

The aim of the work was to assess the potential weaknesses and threats of the integration of a biomass power plant proposed in a depressed area of Spain as well as to analyse the inherent strengths and opportunities that such a project could have in economic, technical or environmental terms. For this purpose an analysis of site, biomass resources, problems associated to fuel mix combustion, electricity production and connection were assessed. The socioeconomic (employment, GDP effects or tax revenue impact) and environmental (human health, soil erosion, fertiliser application) outcomes associated with the proposed biomass scheme have been evaluated. Finally, a list of actions to take into account for successful implementation of this proposed project has been defined. (author)

Strategy for research, development and demonstration of thermal biomass gasification in Denmark

Energy Technology Data Exchange (ETDEWEB)

Hansen, Morten Tony

2011-12-15

Technology for thermal gasification of biomass is one of the key elements to make the vision of an energy system without fossil fuels a reality. Gasification technology can enhance the flexibility needed to maintain a future energy system with a large share of wind power. Furthermore, gasification has advantages in terms of ash recycling and utilisation of vast but challenging biomass residues. Danish companies are globally well advanced with this technology and the market for gasification technology is great in both Denmark and abroad. There is a clear need for targeted technology RD and D in order to reach the last stretch to a commercial breakthrough. The project ''Strategy for research, development and demonstration of thermal biomass gasification in Denmark'' is the Danish industrys contribution to the development of biomass gasification and goes into detail with the RD and D needs. The project has been conducted by FORCE Technology for DI Bioenergy with funding from EUDP, Energinet.dk, DI Bioenergy and FORCE Technology and five stakeholder companies. (LN)

FY 2000 report on the results of the survey on the biomass-derived energy conversion technology. III; 2000 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In relation to the biomass-derived energy conversion technology which was regarded as promising from the results of the survey already made, the survey was made on the present situation and subjects of the technical development, social needs, energy efficiency, economical efficiency and the future. Studies were conducted on the development of technology for effective biomass utilization and the conceptual design and evaluation of a system for effective biomass utilization. As to the effective biomass utilization technology, the survey was made on the biomass combustion power generation technology/gasification power generation technology, gasification methanol synthesis of biomass, biomass gasification dimethyl ether synthesis, technology of ethanol production by alcohol fermentation via saccharification of biomass, methy-esterification of grease biomass, especially palm oil, and diesel oil production via reformation of by-product glycerin, and energy production from biomass using super- (sub- ) critical reaction. As to the system for effective biomass utilization, the survey was carried out of the regional outline, resource amount and sampling amount, selection of the conversion technology, and economical efficiency of Takatsuki city, Osaka, Shimokawa town, Hokkaido, Yufutsu/Hidaka region, Hokkaido, and Aogaki town, Hyogo. (NEDO)

Assessment of biomass cogeneration in the Great Lakes region

International Nuclear Information System (INIS)

Burnham, M.; Easterly, J.L.

1994-01-01

Many biomass cogeneration facilities have successfully entered into power sales agreements with utilities across the country, often after overcoming various difficulties or barriers. Under a project sponsored by the Great Lakes Regional Biomass Energy Program of the U.S. Department of Energy, DynCorp sm-bullet Meridian has conducted a survey of biomass facilities in the seven Great Lakes states, selecting 10 facilities for case studies with at least one facility in each of the seven states. The purpose of the case studies was to address obstacles that biomass processors face in adding power production to their process heat systems, and to provide examples of successful strategies for entering into power sales agreements with utilities. The case studies showed that the primary incentives for investing in cogeneration and power sales are to reduce operating costs through improved biomass waste management and lower energy expenditures. Common barriers to cogeneration and power sales were high utility stand-by charges for unplanned outages and low utility avoided cost payments due to excess utility generation capacity

Air quality on biomass harvesting operations

Science.gov (United States)

Dana Mitchell

2011-01-01

The working environment around logging operations can be very dusty. But, air quality around logging operations is not well documented. Equipment movements and trafficking on the landing can cause dust to rise into the air. The addition of a biomass chipper creates different air flow patterns and may stir up additional dust. This project addresses two topics related to...

Wallowa County Integrated Biomass Energy Center

Energy Technology Data Exchange (ETDEWEB)

Christoffersen, Nils [Wallowa Resources Community Solutions Inc., Wallowa, OR (United States)

2014-05-02

The Integrated Biomass Energy Center (IBEC) is an approximately 0.1 MW CHP integrated biorefinery in Northeastern Oregon which will demonstrate and validate small-scale combined heat and power from lignin intermediates/residues. IBEC will be co-located with feedstock suppliers and thermal and power customers for distributed generation. The project was developed by Wallowa Resources Community Solutions Inc.

Assessment of the externalise of biomass energy for electricity production

Energy Technology Data Exchange (ETDEWEB)

Linares, P; Leal, J; Saez, R M

1996-07-01

This study presents a methodology for the quantification of the socioeconomic and environmental externalities of the biomass fuel cycle. It is based on the one developed by the ExternE Project of the European Commission, based in turm in the damage function approach, and which has been extended and modified for a better adaptation to biomass energy systems. The methodology has been applied to a 20 MW biomass power plant, fueled by Cynara cardunculus, in southern Spain. The externalities addressed have been macroeconomic effects, employment, CO2, fixation, erosion, and non-point source pollution. The results obtained should be considered only as subtotals, since there are still other externalities to be quantified. Anyway, and in spite of the uncertainty existing, these results suggest that the total cost (those including internal and external costs) of biomass energy are lower than those of conventional energy sources, what, if taken into account, would make biomass more competitive than it is now. (Author) 44 refs.

Assessment of the externalities of biomass energy for electricity production

Energy Technology Data Exchange (ETDEWEB)

Linares, P; Leal, J; Saez, R M

1996-10-01

This study presents a methodology for the quantification of the socioeconomic and environmental externalities of the biomass fuel cycle. It is based on the one developed by the ExternE Project of the European Commission, based in turn in the damage function approach, and which has been extended and modified for a better adaptation to biomass energy systems. The methodology has been applied to a 20 MW biomass power plant, fueled by Cynara cardunculus, in southern Spain. The externalities addressed have been macroeconomic effects, employment, CO{sub 2}, fixation, erosion, and non-point source pollution. The results obtained should be considered only as subtotals, since there are still other externalities to be quantified. anyway, and in spite of the uncertainty existing, these results suggest that total cost (those including internal and external costs) of biomass energy are lower than those of conventional energy sources, what, if taken into account, would make biomass more competitive than it is now. (Author)

Assessment of the externalise of biomass energy for electricity production

International Nuclear Information System (INIS)

Linares, P.; Leal, J.; Saez, R.M.

1996-01-01

This study presents a methodology for the quantification of the socioeconomic and environmental externalities of the biomass fuel cycle. It is based on the one developed by the ExternE Project of the European Commission, based in turm in the damage function approach, and which has been extended and modified for a better adaptation to biomass energy systems. The methodology has been applied to a 20 MW biomass power plant, fueled by Cynara cardunculus, in southern Spain. The externalities addressed have been macroeconomic effects, employment, CO2, fixation, erosion, and non-point source pollution. The results obtained should be considered only as subtotals, since there are still other externalities to be quantified. Anyway, and in spite of the uncertainty existing, these results suggest that the total cost (those including internal and external costs) of biomass energy are lower than those of conventional energy sources, what, if taken into account, would make biomass more competitive than it is now. (Author) 44 refs

Methyl halide emission estimates from domestic biomass burning in Africa

Science.gov (United States)

Mead, M. I.; Khan, M. A. H.; White, I. R.; Nickless, G.; Shallcross, D. E.

Inventories of methyl halide emissions from domestic burning of biomass in Africa, from 1950 to the present day and projected to 2030, have been constructed. By combining emission factors from Andreae and Merlet [2001. Emission of trace gases and aerosols from biomass burning. Global Biogeochemical Cycles 15, 955-966], the biomass burning estimates from Yevich and Logan [2003. An assessment of biofuel use and burning of agricultural waste in the developing world. Global Biogeochemical Cycles 17(4), 1095, doi:10.1029/2002GB001952] and the population data from the UN population division, the emission of methyl halides from domestic biomass usage in Africa has been estimated. Data from this study suggest that methyl halide emissions from domestic biomass burning have increased by a factor of 4-5 from 1950 to 2005 and based on the expected population growth could double over the next 25 years. This estimated change has a non-negligible impact on the atmospheric budgets of methyl halides.

Optimal placement of biomass fuelled gas turbines for reduced losses

International Nuclear Information System (INIS)

Jurado, Francisco; Cano, Antonio

2006-01-01

This paper presents a method for the optimal location and sizing of biomass fuelled gas turbine power plants. Both profitability in using biomass and power loss are considered in the cost function. The first step is to assess the plant size that maximizes the profitability of the project. The second step is to determine the optimal location of the gas turbines in the electric system to minimize the power loss of the system

The influence of perceived uncertainty on entrepreneurial action in emerging renewable energy technology; biomass gasification projects in the Netherlands

International Nuclear Information System (INIS)

Meijer, Ineke S.M.; Hekkert, Marko P.; Koppenjan, Joop F.M.

2007-01-01

Emerging renewable energy technologies cannot break through without the involvement of entrepreneurs who dare to take action amidst uncertainty. The uncertainties that the entrepreneurs involved perceive will greatly affect their innovation decisions and can prevent them from engaging in innovation projects aimed at developing and implementing emerging renewable energy technologies. This article analyzes how perceived uncertainties and motivation influence an entrepreneur's decision to act, using empirical data on biomass gasification projects in the Netherlands. Our empirical results show that technological, political and resource uncertainty are the most dominant sources of perceived uncertainty influencing entrepreneurial decision-making. By performing a dynamic analysis, we furthermore demonstrate that perceived uncertainties and motivation are not stable, but evolve over time. We identify critical factors in the project's internal and external environment which influence these changes in perceived uncertainties and motivation, and describe how various interactions between the different variables in the conceptual model (internal and external factors, perceived uncertainty, motivation and previous actions of the entrepreneurs) positively or negatively influence the decision of entrepreneurs to continue entrepreneurial action. We discuss how policymakers can use these insights for stimulating the development and diffusion of emerging renewable energy technologies

CHRISGAS Project. WP13: Ancillary and Novel Processes. Final Report: Separation of Hydrogen with Membranes Combined with Water Gas Shift Reaction

Energy Technology Data Exchange (ETDEWEB)

Sanchez-Hervas, J. M.; Marono, M.; Barreiro, M. M.

2011-05-13

Oxygen pressurized gasification of biomass out stands as a very promising approach to obtain energy or hydrogen from renewable sources. The technical feasibility of this technology has been investigated under the scope of the VI FP CHRISGAS project, which started in September 2004 and had a duration of five and a half years. The Division of Combustion and Gasification of CIEMAT participated in this project in Work Package 13: Ancillary and novel processes, studying innovative gas separation and gas upgrading systems. Such systems include novel or available high temperature water gas shift catalysts and commercially available membranes not yet tried in this type of atmosphere. This report describes the activities carried out during the project regarding the performance of high temperature water gas shift catalysts for upgrading of synthesis gas obtained from biomass gasification, the separation of H2 with selective membranes and the combination of both processes in one by means of a catalytic membrane reactor. (Author) 20 refs.

CHRISGAS Project. WP13: Ancillary and Novel Processes. Final Report: Separation of Hydrogen with Membranes Combined with Water Gas Shift Reaction

International Nuclear Information System (INIS)

Sanchez-Hervas, J. M.; Marono, M.; Barreiro, M. M.

2011-01-01

Oxygen pressurized gasification of biomass out stands as a very promising approach to obtain energy or hydrogen from renewable sources. The technical feasibility of this technology has been investigated under the scope of the VI FP CHRISGAS project, which started in September 2004 and had a duration of five and a half years. The Division of Combustion and Gasification of CIEMAT participated in this project in Work Package 13: Ancillary and novel processes, studying innovative gas separation and gas upgrading systems. Such systems include novel or available high temperature water gas shift catalysts and commercially available membranes not yet tried in this type of atmosphere. This report describes the activities carried out during the project regarding the performance of high temperature water gas shift catalysts for upgrading of synthesis gas obtained from biomass gasification, the separation of H2 with selective membranes and the combination of both processes in one by means of a catalytic membrane reactor. (Author) 20 refs.

Biomass thermochemical conversion - overview of results; Biomassan jalostus - tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K. [VTT Energy, Espoo (Finland). Energy Production Technologies

1995-12-31

In this Bioenergy research program the thermochemical conversion activities are mainly concentrated in three fields (1) flash pyrolysis and the use of wood oil in boilers and engines (2) biomass gasification for gas engine power plants and finally (3) conversion of black liquor and extractives in a pulp mill to various liquid fuels. Parallel to activities in Finland also significant work has been done in EU-Joule and Apas projects and in the IEA Bioenergy Agreement. In the area of flash pyrolysis technology, three new laboratory and PDU-units have been installed to VTT in order to produce various qualities of bio oils from wood and straw. The quality of pyrolysis oils have been characterized by physical and chemical methods supported by EU and IEA networks. Several companies are carrying out pyrolysis activities as well: Neste Oy is testing the wood oil in a 200 kW boiler, Waertsilae Diesel Oy is testing Canadian wood oil in a 1.5 MWe diesel power plant engine and Vapo Oy is carrying out investigations to produce pyrolysis oils in Finland. The biomass gasification coupled to a gas engine is an interesting alternative for small scale power production parallel to existing fluid bed boiler technology. VTT has installed a circulating fluid bed gasifier with advanced gas cleaning system to test various technologies in order to feed the gas to an engine. In order to produce liquid fuels at a pulp mill, the laboratory work has continued using crude soap as a raw material for high pressure liquid phase treatment and atmospheric pyrolysis process. The quality of the oil is like light fuel oil or diesel fuel, possibilities to use it as a lubricant will be investigated

Biomass thermochemical conversion - overview of results; Biomassan jalostus - tutkimusalueen katsaus

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K [VTT Energy, Espoo (Finland). Energy Production Technologies

1996-12-31

In this Bioenergy research program the thermochemical conversion activities are mainly concentrated in three fields (1) flash pyrolysis and the use of wood oil in boilers and engines (2) biomass gasification for gas engine power plants and finally (3) conversion of black liquor and extractives in a pulp mill to various liquid fuels. Parallel to activities in Finland also significant work has been done in EU-Joule and Apas projects and in the IEA Bioenergy Agreement. In the area of flash pyrolysis technology, three new laboratory and PDU-units have been installed to VTT in order to produce various qualities of bio oils from wood and straw. The quality of pyrolysis oils have been characterized by physical and chemical methods supported by EU and IEA networks. Several companies are carrying out pyrolysis activities as well: Neste Oy is testing the wood oil in a 200 kW boiler, Waertsilae Diesel Oy is testing Canadian wood oil in a 1.5 MWe diesel power plant engine and Vapo Oy is carrying out investigations to produce pyrolysis oils in Finland. The biomass gasification coupled to a gas engine is an interesting alternative for small scale power production parallel to existing fluid bed boiler technology. VTT has installed a circulating fluid bed gasifier with advanced gas cleaning system to test various technologies in order to feed the gas to an engine. In order to produce liquid fuels at a pulp mill, the laboratory work has continued using crude soap as a raw material for high pressure liquid phase treatment and atmospheric pyrolysis process. The quality of the oil is like light fuel oil or diesel fuel, possibilities to use it as a lubricant will be investigated

Biomass, the green motor in transition. State-of-the-art after the second phase. Appendices

International Nuclear Information System (INIS)

Gigler, J.

2004-01-01

The project Transition Biomass is part of the transition towards a sustainable energy economy in the Netherlands, initiated by the Ministry of Economic Affairs. The aim of the project is to start a societal process of changes to realize a large-scale and sustainable use of biomass for the production of energy, transportation fuels and products. In the main report an overview is given of the results in 2003. This report comprises the appendices [nl

Biomass-derived Syngas Utilization for Fuels and Chemicals - Final Report

Energy Technology Data Exchange (ETDEWEB)

Dayton, David C

2010-03-24

Executive Summary The growing gap between petroleum production and demand, mounting environmental concerns, and increasing fuel prices have stimulated intense interest in research and development (R&D) of alternative fuels, both synthetic and bio-derived. Currently, the most technically defined thermochemical route for producing alternative fuels from lignocellulosic biomass involves gasification/reforming of biomass to produce syngas (carbon monoxide [CO] + hydrogen [H2]), followed by syngas cleaning, Fischer-Tropsch synthesis (FTS) or mixed alcohol synthesis, and some product upgrading via hydroprocessing or separation. A detailed techno-economic analysis of this type of process has recently been published [1] and it highlights the need for technical breakthroughs and technology demonstration for gas cleanup and fuel synthesis. The latter two technical barrier areas contribute 40% of the total thermochemical ethanol cost and 70% of the production cost, if feedstock costs are factored out. Developing and validating technologies that reduce the capital and operating costs of these unit operations will greatly reduce the risk for commercializing integrated biomass gasification/fuel synthesis processes for biofuel production. The objective of this project is to develop and demonstrate new catalysts and catalytic processes that can efficiently convert biomass-derived syngas into diesel fuel and C2-C4 alcohols. The goal is to improve the economics of the processes by improving the catalytic activity and product selectivity, which could lead to commercialization. The project was divided into 4 tasks: Task 1: Reactor Systems: Construction of three reactor systems was a project milestone. Construction of a fixed-bed microreactor (FBR), a continuous stirred tank reactor (CSTR), and a slurry bubble column reactor (SBCR) were completed to meet this milestone. Task 2: Iron Fischer-Tropsch (FT) Catalyst: An attrition resistant iron FT catalyst will be developed and tested

Estimation of energy potential of agricultural enterprise biomass

Directory of Open Access Journals (Sweden)

Lypchuk Vasyl

2017-01-01

Full Text Available Bioenergetics (obtaining of energy from biomass is one of innovative directions in energy branch of Ukraine. Correct and reliable estimation of biomass potential is essential for efficient use of it. The article reveals the issue of estimation of potential of biomass, obtained from byproducts of crop production and animal breeding, which can be used for power supply of agricultural enterprises. The given analysis was carried with application of common methodological fundamentals, revealed in the estimation of production structure of agricultural enterprises, structure of land employment, efficiency of crops growing, indicators of output of main and by-products, as well as normative (standard parameters of power output of energy raw material in relation to the chosen technology of its utilization. Results of the research prove high energy potential of byproducts of crop production and animal breeding at all of the studied enterprises, which should force its practical use.

Mycelia Biomass Yield of Ganoderma lucidum Mushroom by ...

African Journals Online (AJOL)

Biomass yield of G. lucidum in submerged culture was investigated on account of its requirements for sources of carbon, nitrogen and the carbon : nitrogen (C:N) ratio. The study was carried out with the culture medium of potato dextrose broth enriched with the different carbon (glucose, maltose, starch) and nitrogen ...

Report on investigations in fiscal 2000. International infrastructure improving project for rationalization of energy use (Fundamental survey on effective utilization of unutilized biomass energy in ASEAN countries); 2000 nendo kokusai energy shiyo gorika kiban seibi jigyo chosa hokokusho. ASEAN shokoku ni okeru miriyo baiomasu energy no yuko riyo ni kansuru kisochosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to utilize 'biomass' being the unutilized and reproducible energy source, which exists affluently in the ASEAN countries, investigations and discussions have been carried out on electric power generation using palm shells as fuel in Malaysia. This paper reports the achievement in fiscal 2000. The biomass energy plant project was discussed with the followings as the conditions: an output of 1 MW, use of biomass in the form of wastes discharged from oil palm mills, the system of direct combustion process with boiler/steam turbine generation process, and power transmission to public grids. As a result of the discussions, the following conclusions were obtained: reduction of greenhouse effect gas exhaust will amount to 81,540 t-CO2/year, reduction will be realized on white smoke pollution caused by wastes incineration being criticized from various sectors and such harmful gas exhaust as SOx and NOx discharged from fossil fuel power generation, the uncertainty of electric power supply currently depending on DG power generation will be mitigated resulting in acquisition of economic effects, and electric power supply to 1,000 households will be possible, contributing to enhancement of living standard due to electrification. (NEDO)

The transfer of technologies for biomass energy utilization

International Nuclear Information System (INIS)

Schneiders, H.H.

1995-01-01

The first part of the paper presents the common perception of technology transfer as a trade relationship rather than a systematic approach to establish a complex technological capacity in a given field. It aims to correct this misperception by introducing some other ideas: (a) the need to support the people, adjust the relevant organizations and establish the capacities to provide the products and services; (b) the typical life cycles of technologies from the initial concept to the final stages of transfer and sustainable dissemination; (c) the needs and expectations of the groups targeted by the technologies for biomass energy utilization. The second part of the paper discusses one example of successful technology transfer: the use of large biomass-burning stoves for food preparation in public institutions and private restaurants in East Africa. The third part of the paper highlights two non-technological barriers to the transfer of biomass energy technologies: (a) weak market forces and business interests and a large number of State activities and projects and (b) conflicting interests of end-users, craftsmen, private and public project partners, which can threaten the success of the attempted technology transfer, even after local adaptation. Finally, suggestions are made for overcoming some of these problems. (author)

The transfer of technologies for biomass energy utilization

Energy Technology Data Exchange (ETDEWEB)

Schneiders, H H [German Agency for Technical Cooperation (GTZ), Eschborn (Germany)

1995-12-01

The first part of the paper presents the common perception of technology transfer as a trade relationship rather than a systematic approach to establish a complex technological capacity in a given field. It aims to correct this misperception by introducing some other ideas: (a) the need to support the people, adjust the relevant organizations and establish the capacities to provide the products and services; (b) the typical life cycles of technologies from the initial concept to the final stages of transfer and sustainable dissemination; (c) the needs and expectations of the groups targeted by the technologies for biomass energy utilization. The second part of the paper discusses one example of successful technology transfer: the use of large biomass-burning stoves for food preparation in public institutions and private restaurants in East Africa. The third part of the paper highlights two non-technological barriers to the transfer of biomass energy technologies: (a) weak market forces and business interests and a large number of State activities and projects and (b) conflicting interests of end-users, craftsmen, private and public project partners, which can threaten the success of the attempted technology transfer, even after local adaptation. Finally, suggestions are made for overcoming some of these problems. (author)

Communal biomass conversion plants

International Nuclear Information System (INIS)

1991-06-01

The Coordinating Committee set up by the Danish government in 1986 were given the responsibility of investigating the potentials for biomass conversion plants in Denmark, especially in relation to agricultural, environmental and energy aspects. The results of the Committee's plan of management for this project are presented. This main report covers 13 background reports which deal with special aspects in detail. The report describes the overall plan of management, the demonstration and follow-up programme and the individual biogas demonstration plants. Information gained from these investigations is presented. The current general status, (with emphasis on the technical and economical aspects) and the prospects for the future are discussed. The interest other countries have shown in Danish activities within the field of biogas production is described, and the possibilities for Danish export of technology and know-how in this relation are discussed. It is claimed that Denmark is the first country that has instigated a coordinated development programme for biomass conversion plants. (AB) 24 refs

Optimal use of biomass for energy production

International Nuclear Information System (INIS)

Ruijgrok, W.; Cleijne, H.

2000-10-01

In addition to the EWAB programme, which is focused mainly on the application of waste and biomass for generating electricity, Novem is also working on behalf of the government on the development of a programme for gaseous and liquid energy carriers (GAVE). The Dutch ministries concerned have requested that Novem provide more insight concerning two aspects. The first aspect is the world-wide availability of biomass in the long term. A study group under the leadership of the University of Utrecht has elaborated this topic in greater detail in the GRAIN project. The second aspect is the question of whether the use of biomass for biofuels, as aimed at in the GAVE programme, can go hand in hand with the input for the electricity route. Novem has asked the Dutch research institute for the electric power industry (KEMA) to study the driving forces that determine the future use of biomass for electricity and biofuels, the competitive strength of each of the routes, and the possible future scenarios that emerge. The results of this report are presented in the form of copies of overhead sheets

Financial considerations of policy options to enhance biomass utilization for reducing wildfire hazards

Science.gov (United States)

Dennis R. Becker; Debra Larson; Eini C. Lowell

2009-01-01

The Harvest Cost-Revenue Estimator, a financial model, was used to examine the cost sensitivity of forest biomass harvesting scenarios to targeted policies designed to stimulate wildfire hazardous fuel reduction projects. The policies selected represent actual policies enacted by federal and state governments to provide incentive to biomass utilization and are aimed at...

The IAEA Biomass programme: reference biospheres for long-term safety assessment of high level waste disposal facilities

International Nuclear Information System (INIS)

Metcalf, Phil; Crossland, Ian; Torres, Carlos; Crossland, Ian J.

2002-01-01

Phil Metcalf and Ian Crossland presented the IAEA Biomass project. Phil Metcalf explained that the Biomass project, begun in 1996, by an international forum organised by the IAEA was a very good exercise for exchanging information through technical meetings and documentation such as Biomass newsletters or CD Rom. Ian Crossland continued by giving a presentation of the Biomass theme 1 that concerns the radioactive waste disposal topic. Its objective was mainly to develop the reference biosphere methodology and to demonstrate its usefulness through some exercises related to the development of a practical set of example biospheres such as: 1. drinking water well, 2. agricultural irrigation, with a well source and 3. Set of natural groundwater discharges to natural, semi-natural systems. Input data would always change to accommodate a given repository simulation and location. Thus this project must be seen as a good exercise for the application of a methodology and should be considered as a good source of reference biospheres that might be viewed as a benchmark for comparison with site-specific safety assessments for a selected number of radionuclides. The main conclusion from the Biomass theme 1 project was that there appears to be an international consensus on preparing generic reference biospheres for postclosure safety assessment but waste management organisations should also consider the specific requirements of regulators and other stakeholders

Overview of the Biomass Scenario Model

Energy Technology Data Exchange (ETDEWEB)

Peterson, Steve [Lexidyne, LLC, Colorado Springs, CO (United States)

2015-09-01

This report describes the structure of the October 2012 version of the Biomass Scenario Model (BSM) in considerable detail, oriented towards readers with a background or interest in the underlying modeling structures. Readers seeking a less-detailed summary of the BSM may refer to Peterson (2013). BSM aims to provide a framework for exploring the potential contribution of biofuel technologies to the transportation energy supply for the United States over the next several decades. The model has evolved significantly from the prototype developed as part of the Role of Biomass in America" tm s Energy Future (RBAEF) project. BSM represents the supply chain surrounding conversion pathways for multiple fuel products, including ethanol, butanol, and infrastructure-compatible biofuels such as diesel, jet fuel, and gasoline.

Zooplankton biomass (displacement volume, dry mass, ash-free dry mass) data collected in Eastern Central Atlantic during CIPREA project from 1978-07-25 to 1978-09-12 by France (NODC Accession 0070783)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Zooplankton biomass (displacement volume, dry mass, and ashfree dry mass) data collected in Eastern Central Atlantic during CIPREA project in Jul - Sep 1978 by...

Biomass torrefaction: A promising pretreatment technology for biomass utilization

Science.gov (United States)

Chen, ZhiWen; Wang, Mingfeng; Ren, Yongzhi; Jiang, Enchen; Jiang, Yang; Li, Weizhen

2018-02-01

Torrefaction is an emerging technology also called mild pyrolysis, which has been explored for the pretreatment of biomass to make the biomass more favorable for further utilization. Dry torrefaction (DT) is a pretreatment of biomass in the absence of oxygen under atmospheric pressure and in a temperature range of 200-300 degrees C, while wet torrrefaction (WT) is a method in hydrothermal or hot and high pressure water at the tempertures within 180-260 degrees C. Torrrefied biomass is hydrophobic, with lower moisture contents, increased energy density and higher heating value, which are more comparable to the characteristics of coal. With the improvement in the properties, torrefied biomass mainly has three potential applications: combustion or co-firing, pelletization and gasification. Generally, the torrefaction technology can accelerate the development of biomass utilization technology and finally realize the maximum applications of biomass energy.

Biomass Assessment: A Question of Method and Expertise

International Nuclear Information System (INIS)

Thivolle-Cazat, A.; Le Net, E.; Labalette, F.; Marsac, S.

2013-01-01

Whereas the new stakes on lignocellulosic biomass are often demand-oriented (heat, electricity, biofuels, etc.) mainly through public policies, the new equilibrium will depend also on the supply-side. This supply has to be understood as socio-economic and environmental targets combining many topics: multi- resources (agriculture, forest, 'dedicated coppices', by-products and wastes), available/potential quantities and costs, localisation, replacement/substitution effects (activities, lands), and supply- side stakeholders' behaviours. Many initiatives have been launched to grasp those dimensions through projects (National Research Agency, French Environment and Energy Management Agency, etc.). Many figures exist on the biomass assessment aspect but they are not clear enough and not comparable due to differences in definitions, scopes, data, parameters, geographical levels, reporting units, time-scale, etc. Regarding the characterisation of biomass supply chains, evaluations are often incomplete and lack methodological references. This article aims to focus on methodological key points and barriers to overcome, in order to get a better evaluation and understanding of biomass mobilisation expected by potential users and public authorities. (authors)

Remote Characterization of Biomass Measurements: Case Study of Mangrove Forests

Science.gov (United States)

Fatoyinbo, Temilola E.

2010-01-01

Accurately quantifying forest biomass is of crucial importance for climate change studies. By quantifying the amount of above and below ground biomass and consequently carbon stored in forest ecosystems, we are able to derive estimates of carbon sequestration, emission and storage and help close the carbon budget. Mangrove forests, in addition to providing habitat and nursery grounds for over 1300 animal species, are also an important sink of biomass. Although they only constitute about 3% of the total forested area globally, their carbon storage capacity -- in forested biomass and soil carbon -- is greater than that of tropical forests (Lucas et al, 2007). In addition, the amount of mangrove carbon -- in the form of litter and leaves exported into offshore areas is immense, resulting in over 10% of the ocean's dissolved organic carbon originating from mangroves (Dittmar et al, 2006) The measurement of forest above ground biomass is carried out on two major scales: on the plot scale, biomass can be measured using field measurements through allometric equation derivation and measurements of forest plots. On the larger scale, the field data are used to calibrate remotely sensed data to obtain stand-wide or even regional estimates of biomass. Currently, biomass can be calculated using average stand biomass values and optical data, such as aerial photography or satellite images (Landsat, Modis, Ikonos, SPOT, etc.). More recent studies have concentrated on deriving forest biomass values using radar (JERS, SIR-C, SRTM, Airsar) and/or lidar (ICEsat/GLAS, LVIS) active remote sensing to retrieve more accurate and detailed measurements of forest biomass. The implementation of a generation of new active sensors (UAVSar, DesdynI, Alos/Palsar, TerraX) has prompted the development of new tecm'liques of biomass estimation that use the combination of multiple sensors and datasets, to quantify past, current and future biomass stocks. Focusing on mangrove forest biomass estimation

Developing Government Renewable Energy Projects

Energy Technology Data Exchange (ETDEWEB)

Kurt S. Myers; Thomas L. Baldwin; Jason W. Bush; Jake P. Gentle

2012-07-01

The US Army Corps of Engineers has retained Idaho National Laboratory (INL) to conduct a study of past INL experiences and complete a report that identifies the processes that are needed for the development of renewable energy projects on government properties. The INL has always maintained expertise in power systems and applied engineering and INL’s renewable energy experiences date back to the 1980’s when our engineers began performing US Air Force wind energy feasibility studies and development projects. Over the last 20+ years of working with Department of Defense and other government agencies to study, design, and build government renewable projects, INL has experienced the do’s and don’ts for being successful with a project. These compiled guidelines for government renewable energy projects could include wind, hydro, geothermal, solar, biomass, or a variety of hybrid systems; however, for the purpose of narrowing the focus of this report, wind projects are the main topic discussed throughout this report. It is our thought that a lot of what is discussed could be applied, possibly with some modifications, to other areas of renewable energy. It is also important to note that individual projects (regardless the type) vary to some degree depending on location, size, and need but in general these concepts and directions can be carried over to the majority of government renewable energy projects. This report focuses on the initial development that needs to occur for any project to be a successful government renewable energy project.

Biomass energy: Sustainable solution for greenhouse gas emission

Science.gov (United States)

Sadrul Islam, A. K. M.; Ahiduzzaman, M.

2012-06-01

Biomass is part of the carbon cycle. Carbon dioxide is produced after combustion of biomass. Over a relatively short timescale, carbon dioxide is renewed from atmosphere during next generation of new growth of green vegetation. Contribution of renewable energy including hydropower, solar, biomass and biofuel in total primary energy consumption in world is about 19%. Traditional biomass alone contributes about 13% of total primary energy consumption in the world. The number of traditional biomass energy users expected to rise from 2.5 billion in 2004 to 2.6 billion in 2015 and to 2.7 billion in 2030 for cooking in developing countries. Residential biomass demand in developing countries is projected to rise from 771 Mtoe in 2004 to 818 Mtoe in 2030. The main sources of biomass are wood residues, bagasse, rice husk, agro-residues, animal manure, municipal and industrial waste etc. Dedicated energy crops such as short-rotation coppice, grasses, sugar crops, starch crops and oil crops are gaining importance and market share as source of biomass energy. Global trade in biomass feedstocks and processed bioenergy carriers are growing rapidly. There are some drawbacks of biomass energy utilization compared to fossil fuels viz: heterogeneous and uneven composition, lower calorific value and quality deterioration due to uncontrolled biodegradation. Loose biomass also is not viable for transportation. Pelletization, briquetting, liquefaction and gasification of biomass energy are some options to solve these problems. Wood fuel production is very much steady and little bit increase in trend, however, the forest land is decreasing, means the deforestation is progressive. There is a big challenge for sustainability of biomass resource and environment. Biomass energy can be used to reduce greenhouse emissions. Woody biomass such as briquette and pellet from un-organized biomass waste and residues could be used for alternative to wood fuel, as a result, forest will be saved and

Materials Problems and Solutions in Biomass fired plants

DEFF Research Database (Denmark)

Larsen, Ole Hede; Montgomery, Melanie

2006-01-01

be directly ascribed to the composition of the deposit and the metal surface temperature. In woodchip boilers, a similar corrosion rate and corrosion mechanism has on some occasions been observed. Cofiring of straw (10 and 20% energy basis) with coal has shown corrosion rates lower than those in straw fired......Owing to Denmark's pledge to reduce carbon dioxide emissions, biomass is being increasingly utilised as a fuel for generating energy. Extensive research and development projects, especially in the area of material performance for biomass fired boilers, have been undertaken to make biomass a viable...... fuel resource. When straw is combusted, potassium chloride and potassium sulphate are present in ash products, which condense on superheater components. This gives rise to specific chlorine corrosion problems not previously encountered in coal fired power plants. The type of corrosion attack can...

Materials Problems and Solutions in Biomass Fired Plants

DEFF Research Database (Denmark)

Larsen, Ole Hede; Montgomery, Melanie

2006-01-01

ascribed to the composition of the deposit and the metal surface temperature. In woodchip boilers, a similar corrosion rate and corrosion mechanism has on some occasions been observed. Co-firing of straw (10 and 20% energy basis) with coal has shown corrosion rates lower than those in straw-fired plants......Due to Denmark’s pledge to reduce carbon dioxide emissions, biomass is utilised increasingly as a fuel for generating energy. Extensive research and demonstration projects especially in the area of material performance for biomass fired boilers have been undertaken to make biomass a viable fuel...... resource. When straw is combusted, potassium chloride and potassium sulphate are present in ash products, which condense on superheater components. This gives rise to specific chlorine corrosion problems not previously encountered in coal-fired power plants. The type of corrosion attack can be directly...

The development of effective pretreatment and saccharification techniques for lignocellulosic biomass using radiation

International Nuclear Information System (INIS)

Chung, Dyung Yeoup; Kim, Jin Hong; Lee, Seung Sik; Bai, Hyoung Woo; Lee, Jae Taek; Hong, Sung Hyun; Lee, Eun Mi; Kim, Mi Ja

2011-12-01

The bio-ethanol production from crop resource leads to several problems such as a shortage of provisions, soil acidification, and increase of crop price, whereas lignocellulosic biomass can overcome such problems as mentioned above. That is the reason why, the investigation of ethanol production originated from lignocellulosic materials has carried out all over the world. In present project, we focus on the new method of pretreatment using radiation as well as find out high efficiency process of saccharification through the new microorganisms and enzymes in order to achieve the price competitiveness. The enzymatic hydrolysis in lignocellulosic materials is inhibited by several factors such as crystalline of cellolose, hemicelluloses, and lignin. In order to overcome these obstacles, we devise phyco-chemical and phyco-physical treatments as a combination of 3% sulferic acid and 1000 kGy gamma irradiation and as a popping-1000 kGy gamma irradiation. Most lignocellulosic materials showed above 95% enzymatic hydrolysis using popping or popping-gamma irradiation, while the combination of dilute acid-gamma irradiation showed below 90% enzymatic hydrolysis. Moreover, popping treatment followed by gamma irradiation is much better than gamma irradiation followed by popping for enhancing enzymatic hydrolysis. In conclusions, in case of herbaceous biomass such as wheat straw and switch grass popping treatment, popping treatment only is the best method and in case of woody biomass like a popular fiber and overseas biomass like a coconut fiber, the combination of 1000 kGy gamma irradiation-popping treatments is the most effective method for enzymatic hydrolysis. The achieving 95% of enzymatic hydrolysis is owing to modification of lignin structure, removal of hemicelluloses, and destruction of cellulose crystalline. In addition, we investigated that a new cocktail of enzymes for hydrolysis was designed for boosting enzymatic hydrolysis

The development of effective pretreatment and saccharification techniques for lignocellulosic biomass using radiation

Energy Technology Data Exchange (ETDEWEB)

Chung, Dyung Yeoup; Kim, Jin Hong; Lee, Seung Sik; Bai, Hyoung Woo; Lee, Jae Taek; Hong, Sung Hyun; Lee, Eun Mi; Kim, Mi Ja

2011-12-15

The bio-ethanol production from crop resource leads to several problems such as a shortage of provisions, soil acidification, and increase of crop price, whereas lignocellulosic biomass can overcome such problems as mentioned above. That is the reason why, the investigation of ethanol production originated from lignocellulosic materials has carried out all over the world. In present project, we focus on the new method of pretreatment using radiation as well as find out high efficiency process of saccharification through the new microorganisms and enzymes in order to achieve the price competitiveness. The enzymatic hydrolysis in lignocellulosic materials is inhibited by several factors such as crystalline of cellolose, hemicelluloses, and lignin. In order to overcome these obstacles, we devise phyco-chemical and phyco-physical treatments as a combination of 3% sulferic acid and 1000 kGy gamma irradiation and as a popping-1000 kGy gamma irradiation. Most lignocellulosic materials showed above 95% enzymatic hydrolysis using popping or popping-gamma irradiation, while the combination of dilute acid-gamma irradiation showed below 90% enzymatic hydrolysis. Moreover, popping treatment followed by gamma irradiation is much better than gamma irradiation followed by popping for enhancing enzymatic hydrolysis. In conclusions, in case of herbaceous biomass such as wheat straw and switch grass popping treatment, popping treatment only is the best method and in case of woody biomass like a popular fiber and overseas biomass like a coconut fiber, the combination of 1000 kGy gamma irradiation-popping treatments is the most effective method for enzymatic hydrolysis. The achieving 95% of enzymatic hydrolysis is owing to modification of lignin structure, removal of hemicelluloses, and destruction of cellulose crystalline. In addition, we investigated that a new cocktail of enzymes for hydrolysis was designed for boosting enzymatic hydrolysis.

Microalgal biomass pretreatment for bioethanol production: a review

Directory of Open Access Journals (Sweden)

Jesús Velazquez-Lucio

2018-03-01

Full Text Available Biofuels derived from microalgae biomass have received a great deal of attention owing to their high potentials as sustainable alternatives to fossil fuels. Microalgae have a high capacity of CO2 fixation and depending on their growth conditions, they can accumulate different quantities of lipids, proteins, and carbohydrates. Microalgal biomass can, therefore, represent a rich source of fermentable sugars for third generation bioethanol production. The utilization of microalgal carbohydrates for bioethanol production follows three main stages: i pretreatment, ii saccharification, and iii fermentation. One of the most important stages is the pretreatment, which is carried out to increase the accessibility to intracellular sugars, and thus plays an important role in improving the overall efficiency of the bioethanol production process. Diverse types of pretreatments are currently used including chemical, thermal, mechanical, biological, and their combinations, which can promote cell disruption, facilitate extraction, and result in the modification the structure of carbohydrates as well as the production of fermentable sugars. In this review, the different pretreatments used on microalgae biomass for bioethanol production are presented and discussed. Moreover, the methods used for starch and total carbohydrates quantification in microalgae biomass are also briefly presented and compared.

Woody biomass and bioenergy potentials in Southeast Asia between 1990 and 2020

International Nuclear Information System (INIS)

Sasaki, Nophea; Knorr, Wolfgang; Foster, David R.; Etoh, Hiroko; Ninomiya, Hiroshi; Chay, Sengtha; Sun, Sengxi; Kim, Sophanarith

2009-01-01

Forests in Southeast Asia are important sources of timber and other forest products, of local energy for cooking and heading, and potentially as sources of bioenergy. Many of these forests have experienced deforestation and forest degradation over the last few decades. The potential flow of woody biomass for bioenergy from forests is uncertain and needs to be assessed before policy intervention can be successfully implemented in the context of international negotiations on climate change. Using current data, we developed a forest land use model and projected changes in area of natural forests and forest plantations from 1990 to 2020. We also developed biomass change and harvest models to estimate woody biomass availability in the forests under the current management regime. Due to deforestation and logging (including illegal logging), projected annual woody biomass production in natural forests declined from 815.9 million tons (16.3 EJ) in 1990 to 359.3 million tons (7.2 EJ) in 2020. Woody biomass production in forest plantations was estimated at 16.2 million tons yr -1 (0.3 EJ), but was strongly affected by cutting rotation length. Average annual woody biomass production in all forests in Southeast Asia between 1990 and 2020 was estimated at 563.4 million tons (11.3 EJ) yr -1 declining about 1.5% yr -1 . Without incentives to reduce deforestation and forest degradation, and to promote forest rehabilitation and plantations, woody biomass as well as wood production and carbon stocks will continue to decline, putting sustainable development in the region at risk as the majority of the population depend mostly on forest ecosystem services for daily survival. (author)

Biomass for biogas plants in Denmark - in the short and long term; Biomasse til biogasanlaeg i Danmark - pae kort og langt sigt

Energy Technology Data Exchange (ETDEWEB)

Birkmose, T.; Hjort-Gregersen, K.; Stefanek, K.

2013-04-15

In the short term, it is one of the major challenges for the developments of the biogas sector that resources of organic waste of the type (organic industrial wastes) that have heretofore been used, generally are estimated to be nearly exhausted. This has led to a number of new biogas projects based on the use of corn (energy crops) as additional biomass to livestock manure. However, Danish policy now has implemented a restriction on the use of corn and other energy crops for biogas production. It is with the restriction clarified that there is a need to use other additional biomass for biogas production. There is a need in the short term to clarify how alternative biomasses such as straw, nature preservation biomass, household waste, etc. in a technically and economically reliable and satisfactory way can be used for biogas production, so that the dependence of energy crops can be reduced. Additionally, it will be essential if the yield of using manure can be increased to reduce economic dependence on energy crops. In the longer term it is essential to strengthen the assessment of the resource potential of biomass available for the production of biogas, and thus what the contribution of biogas in the long term is estimated to be in the future energy supply based on renewable energy. The present report presents the current and future biomass resources potential and biogas production potential. The biomass resources are primarily agricultural and municipal wastes. (LN)

Characterization of Residual Particulates from Biomass Entrained Flow Gasification

DEFF Research Database (Denmark)

Qin, Ke; Lin, Weigang; Fæster, Søren

2013-01-01

Biomass gasification experiments were carried out in a bench scale entrained flow reactor, and the produced solid particles were collected by a cyclone and a metal filter for subsequent characterization. During wood gasification, the major part of the solid material collected in the filter is soot...

Influence of lignin on biochemical methane potential of biomass for biogas production

DEFF Research Database (Denmark)

Triolo, Jin Mi; Sommer, Sven G.; Møller, Henrik Bjarne

2011-01-01

model for these two biomass groups. Validation of the combined model was carried out using datasets from the literature. This study showed that lignin was not degraded during anaerobic digestion. Furthermore, lignin concentration in organic materials was the strongest predictor of BMP for all...... the biomass groups. The square of the sample correlation coefficient (R2) from the BMP versus lignin was 0.908 (P lignin concentration could be used to predict...

Evaluation on the Efficiency of Biomass Power Generation Industry in China

Directory of Open Access Journals (Sweden)

Jingqi Sun

2014-01-01

Full Text Available As a developing country with large population, China is facing the problems of energy resource shortage and growing environmental pollution arising from the coal-dominated energy structure. Biomass energy, as a kind of renewable energy with the characteristics of being easy to store and friendly to environment, has become the focus of China’s energy development in the future. Affected by the advanced power generation technology and diversified geography environment, the biomass power generation projects show new features in recent years. Hence, it is necessary to evaluate the efficiency of biomass power generation industry by employing proper method with the consideration of new features. In this paper, the regional difference as a new feature of biomass power generation industry is taken into consideration, and the AR model is employed to modify the zero-weight issue when using data envelopment analysis (DEA method to evaluate the efficiency of biomass power generation industry. 30 biomass power generation enterprises in China are selected as the sample, and the efficiency evaluation is performed. The result can provide some insights into the sustainable development of biomass power generation industry in China.

Adsorption characteristics of SO{sub 2}, NO by steam activated biomass chars

Energy Technology Data Exchange (ETDEWEB)

Lu, Fei; Shu, Tong; Wang, Kuan; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

2013-07-01

Wheat straw and rice husk collected from the suburb of Nanjing, China, were prepared to different kinds of steam activated biomass-based chars, and the adsorption characteristics of the biomass-based chars was carried out in a fixed bed reactor. The specific surface area and pore structure of different biomass chars were measured by nitrogen adsorption-desorption analysis instrument at 77K. The effects of biomass type, pyrolysis temperature, heating rate, activation temperature and concentration of SO{sub 2}, NO on the adsorption efficiency of SO{sub 2}, NO were analyzed. The results indicated that the steam activation has significant effects on the specific surface area, total pore volume and micro-morphology of biomass chars by improving the internal structure. The adsorption efficiency of SO{sub 2}, NO increased with the decreasing of SO{sub 2}, NO concentration in the experimental range. The optimal condition of char preparation (873K, fast pyrolysis) and steam activation (1,073K) was proposed based on the adsorption efficiency and adsorption volume of SO{sub 2}, NO. It builds a theoretical basis for industrial applications of biomass.

Renewable energy--traditional biomass vs. modern biomass

International Nuclear Information System (INIS)

Goldemberg, Jose; Teixeira Coelho, Suani

2004-01-01

Renewable energy is basic to reduce poverty and to allow sustainable development. However, the concept of renewable energy must be carefully established, particularly in the case of biomass. This paper analyses the sustainability of biomass, comparing the so-called 'traditional' and 'modern' biomass, and discusses the need for statistical information, which will allow the elaboration of scenarios relevant to renewable energy targets in the world

Energy from biomass and biofuels. Current market initiatives. Altener seminar, Amsterdam, Netherlands, 26 May 1997

International Nuclear Information System (INIS)

1997-01-01

Biomass, organic wastes, hydroelectric power, wind power and solar energy contribute to approximately 6% of the current energy demand in the European Union (EU). Goals are set by the EU to double this share in the energy production in the next decade. The EU Altener Programme aims to increase the use of renewables as source of energy, the trade in renewable energy products and related equipment and services, supporting a wide variety of projects, sector and market studies, events and technical standards. The Agricultural and Forestrial Biomass Network (AFB-Nett) promotes and stimulates, as part of the Altener Programme, the implementation and commercial exploitation of energy from biomass by the initiation of among other things business opportunities and information exchange. The AFB-Nett National Coordinator for the Netherlands, Novem, organised in this respect the title seminar. 85 participants from several European countries attended presentations covering the whole bio-energy chain: from information on biomass supply, through trade, logistics and pretreatment issues up to discussion on conversion technologies. It became clear to the audience that it is a necessary condition to take into account the total chain when developing projects in a specific field of this chain. However, non-technical aspects must be considered as well. Therefore, in developing business opportunities the challenge remains to connect all good project initiatives covering parts of the chain into a few 'whole-chain'-projects

Oil palm biomass as a sustainable energy source: A Malaysian case study

International Nuclear Information System (INIS)

Shuit, S.H.; Tan, K.T.; Lee, K.T.; Kamaruddin, A.H.

2009-01-01

It has been widely accepted worldwide that global warming is by far the greatest threat and challenge in the new millennium. In order to stop global warming and to promote sustainable development, renewable energy is a perfect solution to achieve both targets. Presently million hectares of land in Malaysia is occupied with oil palm plantation generating huge quantities of biomass. In this context, biomass from oil palm industries appears to be a very promising alternative as a source of raw materials including renewable energy in Malaysia. Thus, this paper aims to present current scenario of biomass in Malaysia covering issues on availability and sustainability of feedstock as well as current and possible utilization of oil palm biomass. This paper will also discuss feasibility of some biomass conversion technologies and some ongoing projects in Malaysia related to utilization of oil palm biomass as a source of renewable energy. Based on the findings presented, it is definitely clear that Malaysia has position herself in the right path to utilize biomass as a source of renewable energy and this can act as an example to other countries in the world that has huge biomass feedstock. (author)

Economic evaluation of technical, environmental and institutional barriers on biomass residue collection cost in California

International Nuclear Information System (INIS)

Sethi, P.; Tiangco, V.; Dee, V.; Simons, G.; Lee, Y.; Yomogida, D.

1999-01-01

This paper deals with the economic impacts of the technical, environmental, and institutional barriers in the production, harvesting, and processing of various biomass fuels in California. For each biomass fuel, a base case scenario was developed to characterize the procedures of harvesting, processing and transporting. An economic model was utilized to project the biomass production costs supplied to direct-combustion power plants for each technical, environmental, and institutional barrier. These results will enable the California Energy Commission to identify the most significant barriers to economical biomass energy production (production, harvesting, and processing). (author)

A comparison of selected parametric and non-parametric imputation methods for estimating forest biomass and basal area

Science.gov (United States)

Donald Gagliasso; Susan Hummel; Hailemariam. Temesgen

2014-01-01

Various methods have been used to estimate the amount of above ground forest biomass across landscapes and to create biomass maps for specific stands or pixels across ownership or project areas. Without an accurate estimation method, land managers might end up with incorrect biomass estimate maps, which could lead them to make poorer decisions in their future...

Woody biomass policies and location decisions of the woody bioenergy industry in the southern United States

International Nuclear Information System (INIS)

Guo, Zhimei; Hodges, Donald G.; Young, Timothy M.

2013-01-01

Woody biomass for bioenergy production has been included in relatively few renewable energy policies since the 1970s. Recently, however, several states have implemented a variety of new woody biomass policies to spur the establishment of new bioenergy industry. Establishing new woody biomass-based facilities in a specific state is affected by a number of factors such as the strength of these new policy incentives, resource availability, business tax climate, and the available labor force. This study employs a conditional logit model (CLM) to explore the effects of woody biomass policies on the siting decisions of new bioenergy projects relative to some of these other state attributes. The CLM results suggest that state government incentives are significantly related to state success in attracting new plants. The results have substantial implications regarding woody biomass policies and the creation of a new bioenergy industry. -- Highlights: •This study explores the effects of state attributes on the siting decisions of new woody bioenergy projects. •Results suggest that state woody biomass policies are significantly related to state success in attracting new plants. •Other factors related to the siting of woody bioenergy facilities include resource availability, taxes, and wage rate

Laboratory Scale Coal And Biomass To Drop-In Fuels (CBDF) Production And Assessment

Energy Technology Data Exchange (ETDEWEB)

Lux, Kenneth [Altex Technologies Corporation, Sunnyvale, CA (United States); Imam, Tahmina [Altex Technologies Corporation, Sunnyvale, CA (United States); Chevanan, Nehru [Altex Technologies Corporation, Sunnyvale, CA (United States); Namazian, Mehdi [Altex Technologies Corporation, Sunnyvale, CA (United States); Wang, Xiaoxing [Pennsylvania State Univ., University Park, PA (United States); Song, Chunshan [Pennsylvania State Univ., University Park, PA (United States)

2016-06-29

This Final Technical Report describes the work and accomplishments of the project entitled, “Laboratory Scale Coal and Biomass to Drop-In Fuels (CBDF) Production and Assessment.” The main objective of the project was to fabricate and test a lab-scale liquid-fuel production system using coal containing different percentages of biomass such as corn stover and switchgrass at a rate of 2 liters per day. The system utilizes the patented Altex fuel-production technology, which incorporates advanced catalysts developed by Pennsylvania State University. The system was designed, fabricated, tested, and assessed for economic and environmental feasibility relative to competing technologies.

Biomass - Overview of Swiss Research Programme 2003

International Nuclear Information System (INIS)

Binggeli, D.; Guggisberg, B.

2003-01-01

This overview for the Swiss Federal Office of Energy (SFOE) discusses the results obtained in 2003 in various research projects worked on in Switzerland on the subject of biomass. In the biomass combustion area, subjects discussed include system optimisation for automatic firing, combustion particles, low-particle pellet furnaces, design and optimisation of wood-fired storage ovens, efficiency of filtering techniques and methane generation from wood. Also, an accredited testing centre for wood furnaces is mentioned and measurements made on an installation are presented. As far as the fermentation of biogenic wastes is concerned, biogas production from dairy-product wastes is described. Other projects discussed include a study on eco-balances of energy products, certification and marketing of biogas, evaluation of membranes, a measurement campaign for solar sludge-drying, the operation of a percolator installation for the treatment of bio-wastes, the effects of compost on the environment and the fermentation of coffee wastes. Also, statistics on biogas production in 2002 is looked at. Finally, a preliminary study on biofuels is presented

Explaining the failure of the Dutch innovation system for biomass digestion-A functional analysis

International Nuclear Information System (INIS)

Negro, Simona O.; Hekkert, Marko P.; Smits, Ruud E.

2007-01-01

Since the 1970s research on energy conversion technologies, such as biomass digestion, has been carried out in the Netherlands. However, after 30 years biomass digestion has not been implemented on large scale. The aim of this paper is to create insight into the underlying factors of this troublesome trajectory by applying the 'Functions of Innovation Systems' framework. This results in clear understanding of the (lack of) activities that took place in the innovation system of biomass digestion and the role of government policy in both inducing and blocking this development. The analysis provides several lessons to take into account when developing policies for the acceleration of the development and diffusion of biomass energy

Economic feasibility study of an electric generation project from bagasse gasification in a cuban sugar mill

International Nuclear Information System (INIS)

Torres Fernández, Alfredo; Almazán del Olmo, Oscar; Hernández, Bárbara

2015-01-01

Some solid fuels which are very pollutant and with low value could be transformed into a clean gas that could be used in many industrial applications for its physical properties and for being easy transported. Then, electricity generation is one of the most important applications. In this case, electricity could be generated, cleanly and efficiently, through the use of synthesis gas that replaces the natural gas in a combined cycle (Biomass Integrated Gasification Combined Cycle (BIGCC)).In this paper, we carry out an economic feasibility study of the project about the implementation of Biomass Integrated Gasification Combined Cycle (BIGCC) in a 10000 tc/d sugar mill from bagasse gasification in order to demonstrate, from the economic point of view, the possibility of investment in this kind of technology considering the current conditions of Cuban sugar industry.Later, a sensitivity analysis is presented to show first, the break-even point associated to the project and second, the variations of financial indicators due to changes on the total amount of investments, which is a very helpful element for making right decisions in the project investment process. (author)

Biomass fuels in district heating systems. Final report. Biobrensel i fjernvarmesystem. Sluttrapport

Energy Technology Data Exchange (ETDEWEB)

Otterstad, B.

1987-02-01

The report deals with an energy conservation project on district heating. The project gives a cost comparison between a biomass fuelled system for the local water heating/electric power supply and the development of hydroelectric power. The computer program ESENTRAL is used in the simulation. 3 drawings.

A review on advances of torrefaction technologies for biomass processing

Energy Technology Data Exchange (ETDEWEB)

Acharya, Bimal; Sule, Idris; Dutta, Animesh [University of Guelph, School of Engineering, Guelph, ON (Canada)

2012-12-15

Torrefaction is a thermochemical pretreatment process at 200-300 C in an inert condition which transforms biomass into a relatively superior handling, milling, co-firing and clean renewable energy into solid biofuel. This increases the energy density, water resistance and grindability of biomass and makes it safe from biological degradation which ultimately makes easy and economical on transportation and storing of the torrefied products. Torrefied biomass is considered as improved version than the current wood pellet products and an environmentally friendly future alternative for coal. Torrefaction carries devolatilisation, depolymerization and carbonization of lignocellulose components and generates a brown to black solid biomass as a productive output with water, organics, lipids, alkalis, SiO{sub 2}, CO{sub 2}, CO and CH{sub 4}. During this process, 70 % of the mass is retained as a solid product, and retains 90 % of the initial energy content. The torrefied product is then shaped into pellets or briquettes that pack much more energy density than regular wood pellets. These properties minimize on the difference in combustion characteristics between biomass and coal that bring a huge possibility of direct firing of biomass in an existing coal-fired plant. Researchers are trying to find a solution to fire/co-fire torrefied biomass instead of coal in an existing coal-fired based boiler with minimum modifications and expenditures. Currently available torrefied technologies are basically designed and tested for woody biomass so further research is required to address on utilization of the agricultural biomass with technically and economically viable. This review covers the torrefaction technologies, its' applications, current status and future recommendations for further study. (orig.)

Liquid phase in situ hydrodeoxygenation of biomass-derived phenolic compounds to hydrocarbons over bifunctional catalysts

Science.gov (United States)

Junfeng Feng; Chung-yun Hse; Zhongzhi Yang; Kui Wang; Jianchun Jiang; Junming Xu

2017-01-01

The objective of this study was to find an effective method for converting renewable biomass-derived phenolic compounds into hydrocarbons bio-fuel via in situ catalytic hydrodeoxygenation. The in situ hydrodeoxygenation of biomass-derived phenolic compounds was carried out in methanol-water solvent over bifunctional catalysts of Raney Ni and HZSM-5 or H-Beta. In the in...

Environmental burdens over the entire life cycle of a biomass CHP plant

International Nuclear Information System (INIS)

Jungmeier, G.; Spitzer, J.; Resch, G.

1998-01-01

To increase the use of biomass for energy production it is important to know the possible and significant environmental effects. A life cycle inventory (LCI) was made on a 1.3 MW el biomass CHP plant located in Reuthe/Vorarlberg/Austria with the purpose of analysing the different environmental burdens over the entire life cycle. The plant is fired with coarse and small fuelwood (10,000 t/yr) from industrial waste and forest residues. The boiler for the steam process has a moving grate burner and a muffle burner. The annual production is 4700 MWh of electricity and 29,000 MWh of district heat. The methodology of the analysis is orientated on the ISO Committee Draft of the Series 13,600. The analysis was carried out for the different sections of the biomass plant over their entire life cycle-construction (1 yr), operation (20 yrs) and dismantling (1 yr). The plant in Reuthe, which is the first cogeneration system of this kind in Austria, is a model for other similar projects. The results are shown as environmental burdens of one year and of the entire life cycle. Some results of the life cycle inventory, like the mass and energy balances, selected emissions to air, allocation results and effects on carbon storage pools are given. The results demonstrate that depending on the stage and the period of life, different environmental burdens become significant, i.e. CO 2 emissions of fossil fuels during construction. NO x emission during operation, emissions to soil during dismantling. The different options for allocation the environmental burdens to electricity and heat show a wide range of possible results, depending on the choice of allocation parameters (energy, exergy, credits for heat or electricity, price) i.e. for the particles emissions: 161 mg/kWh el to minus 566 mg/kWh el , 0 mg/kWh th to 118 mg/kWh th . With the results of the analysis it is thus possible for future similar projects to know when and where significant environmental burdens might be further

The use of agricultural biomass for energy purposes: EU and national policy

OpenAIRE

Sabrina Giuca

2008-01-01

The implementation in 2020 of binding national targets for reducing greenhouse gas emissions and use of renewable energy has increased the interest in biomass as a viable alternative to fossil fuels. Thus agriculture acquires a primary role for the reduction of CO2 but raises many issues: CBA, food vs fuel, subsidies, tax measures and investments. After outlining the framework for the exploitation of biomass energy, the analysis carried out on the prospects of development of agroenergy chains...

Feasibility study for biomass power plants in Thailand. Volume 1. Main report. Export trade information

International Nuclear Information System (INIS)

1997-01-01

This study, conducted by Black and Veatch, was funded by the U.S. Trade and Development Agency. The report presents a technical and commercial analysis for the development of three nearly identical electricity generating facilities (biomass steam power plants) in the towns of Chachoengsao, Suphan Buri, and Pichit in Thailand. The Main Report is divided into the following sections: (1.0) Executive Study; (2.0) Project Objectives; (3.0) Review of Combustion Technology for Biomass Fueled Steam Generator Units; (4.0) Conceptual Design; (5.0) Plant Descriptions; (6.0) Plant Operations Staffing; (7.0) Project Schedule; (8.0) Project Cost Estimate; (9.0) Financial Analysis; Appendix - Financial Analysis

Bio energy: Production of Biomass; Produksjon av biomasse

Energy Technology Data Exchange (ETDEWEB)

Noreng, Katrina; Indergaard, Mentz; Liodden, Ole Joergen; Hohle, Erik Eid; Sandberg, Eiliv

2001-07-01

This is Chapter 2 of the book ''Bio energy - Environment, technique and market''. Its main sections are: (1) Biomass resources in Norway, (2) The foundation - photosynthesis, (3) Biomass from forestry, (4) Biomass from peat lands, (5) Biomass from agriculture and (6) Biomass from lakes and sea. The exposition largely describes the conditions in Norway, where the use of bio energy can be increased from 15 TWh to 35 TWh using available technology. At present, water-borne heating systems are not extensively used in Norway and 30% of the biomass that is cut in the forests remains there as waste. Using this waste for energy generation would not only contribute to reduce the emission of greenhouse gases, but would often lead to improved forest rejuvenation. Use of a few per thousand of the Norwegian peat lands would produce 2 - 3 TWh. According to calculations, along the coast of Norway, there are at least 15 mill tonnes of kelp and sea tangle and these resources can be utilized in a sustainable way.

Sustainable biomass production for energy in Sri Lanka

International Nuclear Information System (INIS)

Perera, K.K.C.K.; Rathnasiri, P.G.; Sugathapala, A.G.T.

2003-01-01

The present study concentrates mainly on the estimation of land availability for biomass production and the estimation of sustainable biomass production potential for energy. The feasible surplus land area available for bioenergy plantation is estimated assuming two land availability scenarios (Scenarios 1 and 2) and three biomass demand scenarios (IBD Scenario, SBD Scenario and FBD Scenario). Scenario 1 assumes that 100% of the surplus area available in base year 1997 will be suitable for plantation without considering population growth and food production and that 75% of this surplus land is feasible for plantation. Scenario 2 assumes that future food requirement will grow by 20% and the potential surplus area will be reduced by that amount. The incremental biomass demand scenario (IBD Scenario) assumes that only the incremental demand for biomass in the year 2010 with respect to the base year 1997 has to be produced from new plantation. The sustainable biomass demand scenario (SBD Scenario) assumes that the total sustainable supply of biomass in 1997 is deducted from the future biomass demand in 2010 and only the balance is to be met by new plantation. The full biomass demand scenario (FBD Scenario) assumes that the entire projected biomass demand of the year 2010 needs to be produced from new plantation. The total feasible land area for the scenarios IBD-1, 1BD-2, SBD-1, SBD-2, FBD-1 and FBD-2 are approximately 0.96, 0.66, 0.80, 0.94, 0.60 and 0.30 Mha, respectively. Biomass production potential is estimated by selecting appropriate plant species, plantation spacing and productivity level. The results show that the total annual biomass production in the country could vary from 2 to 9.9 Mt. With the production option (i.e. 1.5 mx1.5 m spacing plantation with fertilizer application) giving the highest yield, the total biomass production for energy under IBD Scenario would be 9.9 Mt yr -1 for Scenario 1 and 6.7 Mt yr -1 for Scenario 2. Under SBD Scenario, the

Catalytic Partial Oxidation of Biomass/Oil Mixture

Czech Academy of Sciences Publication Activity Database

Veselý, Václav; Hanika, Jiří; Tukač, V.; Lederer, J.; Kovač, D.

2013-01-01

Roč. 7, č. 10 (2013), s. 1940-1945 ISSN 1934-8983 R&D Projects: GA TA ČR TE01020080; GA MPO 2A-2TP1/024 Institutional support: RVO:67985858 Keywords : hydrocarbon oil * biomass * catalytic partial oxidation Subject RIV: CI - Industrial Chemistry, Chemical Engineering http://www.davidpublishing.com/journals_info.asp?jId=1718#

Global patterns and predictions of seafloor biomass using random forests

Digital Repository Service at National Institute of Oceanography (India)

Wei, Chih-Lin; Rowe, G.T.; Escobar-Briones, E.; Boetius, A; Soltwedel, T.; Caley, M.J.; Soliman, Y.; Huettmann, F.; Qu, F.; Yu, Z.; Pitcher, C.R.; Haedrich, R.L.; Wicksten, M.K.; Rex, M.A; Baguley, J.G.; Sharma, J.; Danovaro, R.; MacDonald, I.R.; Nunnally, C.C.; Deming, J.W.; Montagna, P.; Levesque, M.; Weslawsk, J.M.; Wlodarska-Kowalczuk, M.; Ingole, B.S.; Bett, B.J.; Billett, D.S.M.; Yool, A; Bluhm, B.A; Iken, K.; Narayanaswamy, B.E.

A comprehensive seafloor biomass and abundance database has been constructed from 24 oceanographic institutions worldwide within the Census of Marine Life (CoML) field projects. The machine-learning algorithm, Random Forests, was employed to model...

Biomass energy in the making

International Nuclear Information System (INIS)

Anon.

2008-01-01

Wood, straw, agricultural residues, organic wastes, biomass is everywhere you look. But the efficient use of this source of green electricity - the world's second largest renewable energy source - requires optimization of biomass collection and combustion processes. Biomass is back on the political agenda. In mid-June of this year, the French government gave this renewable energy a boost by selecting twenty-two projects to generate power and heat with biomass. The plants, to be commissioned by 2010, will be located in eleven different regions and will consume energy from organic plant matter. The power generated will be bought at a firm price of 128 euros per megawatt-hour. Most of the fuel will come from forest and paper industry waste, but straw and even grape pomace will be used in some cases. The plants will have a combined generating capacity of 300 MWh, raising France's installed biomass capacity to a total of 700 MWe. A drop of water in the ocean in the overall scheme of France's electricity. It is true that France has long neglected biomass. In 2004, electricity generated from biological resources represented a mere 1.74 TWhe in France, just 0.3% of its power consumption. This will rise to 0.6% once the new plants have come on line. The trend is the same in all of the EU's 27 member states, according to Eurostat, the statistical office of the European Communities: the amount of electricity generated from biomass (including biogas, municipal waste and wood) has practically doubled in six years, rising from 40 to 80 TWhe between 2000 and 2005. This is an improvement, but it still only represents 2.5% of the electricity supplied to Europeans. On a global scale, biomass contributes just 1% of total electric power generation. Yet biomass is an energy resource found all over the world, whether as agricultural waste, wood chips, or dried treatment plant sludge, to name but a few. Biomass power plants have managed to gain a foothold mainly in countries that produce

Biomass Gasification. The characteristics of technology development and the rate of learning

Energy Technology Data Exchange (ETDEWEB)

Dorca Duch, Andreu; Huertas Bermejo, Javier

2008-09-15

Gasification is considered one of the most promising technologies in biomass applications. The higher efficiency compared to boiler power systems, the perspectives in fuel synthesis and its environmental friendly features are some examples of its potential. Biomass gasification has evolved since its first applications, but it has not been possible to reach a solid commercial stage, except during periods of crises and only for some specific applications. Meanwhile, other gasification technologies, fed by fossil fuels, are currently widely used on industrial scales. This thesis aims to analyze the knowledge development and diffusion patterns of the biomass gasification technology since 1970s in Austria, Finland, Germany and Sweden. Additionally, it seeks to identify the factors that strengthen and weaken the learning process. Finally, the concept of learning curve will be used to numerically assess the rate of learning in small scale biomass gasification for electricity generation. The feasibility of various future scenarios will be evaluated in order to know what is the likelihood for the technology to become competitive in the short term. To do so, the historical evolution of biomass gasification in Austria, Finland, Germany and Sweden has been analyzed. These countries have been selected due to the increasing number of ongoing projects and initiatives since 1970. Subsequently, the development of this technology has been encouraged by two historical facts. Initially, the price of fossil fuels grew in 1973 and 1979 enhancing the interest for biomass gasification as a future alternative. Afterwards, the willingness, shown by the mentioned countries, to reduce greenhouse gases emissions following the Kyoto protocol has revived the interest in biomass gasification. However, none of these two events has driven this technology sufficiently to achieve a sustainable commercial status. In addition, small and large scale projects have followed different development processes

Biomass market and trade in Norway: Status and future prospects

International Nuclear Information System (INIS)

Troemborg, Erik; Bolkesjoe, Torjus Folsland; Solberg, Birger

2008-01-01

This paper gives an overview of bioenergy use, prices, markets and markets prospects in Norway. The current energy production based on biomass in Norway is about 50 pJ or 10% of the stationary energy consumption. About one-half is produced and used in forest industries. The main share of bioenergy used by households consists of firewood in stoves. The use of refined, solid biofuels in heat production is hampered by low coverage of water-borne heating systems and historically low end-user prices of electricity. Harvest levels in Norwegian forests are much below annual growth, implying that forest biomass resources steadily accumulate. Decreasing wood prices combined with rising prices of oil and electricity in recent year have improved competitiveness of solid biofuels in the heat market. Projections of future bioenergy use in Norway using a partial equilibrium forest sector model suggest that bioenergy use will increase in some market segments with the current price levels of electricity and oil. However, quite minor improvements of bioenergy competitiveness or increased energy prices may release substantially higher bioenergy use. A net increase in bioenergy use of 5 TWh (18 PJ) by 2010 is realistic, but requires public awareness of the opportunities in bioenergy technologies, as well as significant economic incentives. Wood stoves and replacement of oil-boilers in central heating systems show highest competitiveness, whereas district heating systems need higher energy prices or more subsidies to be competitive. Biomass for combined heat and power projects or domestically produced liquid biofuels seems to have limited competitiveness in the short term. On the raw material side, wood residues, and roundwood from pine and non-coniferous species represent the main potential, whereas spruce continues to be consumed by the forest industries. According to the model projections, imported biomass will take a significant share of the possible increase of wood consumption

An efficient proteomic approach to analyze agriculture crop biomass

Czech Academy of Sciences Publication Activity Database

Flodrová, Dana; Bobálová, Janette

2013-01-01

Roč. 32, č. 5 (2013), s. 365-372 ISSN 1572-3887 R&D Projects: GA MŠk 1M0570 Institutional support: RVO:68081715 Keywords : MALDI * biomass * proteomics * identification * hemicellulases Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 1.039, year: 2013

Development of a commercial enzymes system for lignocellulosic biomass saccharification

Energy Technology Data Exchange (ETDEWEB)

Kumar, Manoj

2012-12-20

DSM Innovation Inc., in its four year effort was able to evaluate and develop its in-house DSM fungal cellulolytic enzymes system to reach enzyme efficiency mandates set by DoE Biomass program MYPP goals. DSM enzyme cocktail is uniquely active at high temperature and acidic pH, offering many benefits and product differentiation in 2G bioethanol production. Under this project, strain and process development, ratio optimization of enzymes, protein and genetic engineering has led to multitudes of improvement in productivity and efficiency making development of a commercial enzyme system for lignocellulosic biomass saccharification viable. DSM is continuing further improvement by additional biodiversity screening, protein engineering and overexpression of enzymes to continue to further lower the cost of enzymes for saccharification of biomass.

Fiscal 1998 research report. Improvement project of low-grade coals in Chongqing City, China for CO{sub 2} reduction (Feasibility study on the production business of coal- biomass briquette); 1998 nendo chosa hokokusho. CO{sub 2} sakugen no tame no Chuka Jinmin Kyowakoku Jukei chokkatsushi no teihin'i sekitanshitsu no kaizen project (Bio briquette seizo jigyo no chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study was made on the effect of introduction of production technology of coal-biomass briquette (Japanese coal improvement technology) in Chongqing City on reduction of greenhouse effect gases and acid rain causative substances, and sustainable economic growth. The study result on the feasibility of this project and reduction of greenhouse effect gases was summarized. In this feasibility study, Japan-China joint field survey, and both proximate and ultimate analyses of obtained raw materials were carried out. Based on the experimental result in the pilot briquette plant in Chongqing City, study was made on the necessary of the 1 Mtons/y class pilot plant in the pilot area including Nantong coal mine in Chongqing City, and the location, investment, production cost and distribution means of the plant. Based on the evaluation result on CO{sub 2} reduction effect, economical efficiency, environment effect and social effect, its urgency and effectiveness as international cooperation project by yen credit were also confirmed. It is extremely important to promote localization of the plant in the future. (NEDO)

Fiscal 1998 research report. Improvement project of low-grade coals in Chongqing City, China for CO{sub 2} reduction (Feasibility study on the production business of coal- biomass briquette); 1998 nendo chosa hokokusho. CO{sub 2} sakugen no tame no Chuka Jinmin Kyowakoku Jukei chokkatsushi no teihin'i sekitanshitsu no kaizen project (Bio briquette seizo jigyo no chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study was made on the effect of introduction of production technology of coal-biomass briquette (Japanese coal improvement technology) in Chongqing City on reduction of greenhouse effect gases and acid rain causative substances, and sustainable economic growth. The study result on the feasibility of this project and reduction of greenhouse effect gases was summarized. In this feasibility study, Japan-China joint field survey, and both proximate and ultimate analyses of obtained raw materials were carried out. Based on the experimental result in the pilot briquette plant in Chongqing City, study was made on the necessary of the 1 Mtons/y class pilot plant in the pilot area including Nantong coal mine in Chongqing City, and the location, investment, production cost and distribution means of the plant. Based on the evaluation result on CO{sub 2} reduction effect, economical efficiency, environment effect and social effect, its urgency and effectiveness as international cooperation project by yen credit were also confirmed. It is extremely important to promote localization of the plant in the future. (NEDO)

Biomass recalcitrance

DEFF Research Database (Denmark)

Felby, Claus

2009-01-01

Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes - this co......Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes...... - this collective resistance is known as "biomass recalcitrance." Breakthrough technologies are needed to overcome barriers to developing cost-effective processes for converting biomass to fuels and chemicals. This book examines the connection between biomass structure, ultrastructure, and composition......, to resistance to enzymatic deconstruction, with the aim of discovering new cost-effective technologies for biorefineries. It contains chapters on topics extending from the highest levels of biorefinery design and biomass life-cycle analysis, to detailed aspects of plant cell wall structure, chemical treatments...

Feasibility study : identifying economic opportunities for bugwood and other biomass resources in Alberta and BC

International Nuclear Information System (INIS)

2008-04-01

This feasibility study discussed energy technologies for biomass feedstocks including mill residues, roadside residues, and non-merchantable tree stands in Alberta and British Columbia (BC). The study demonstrated that the lack of mill residue resources means that targeted government support may be needed to help the energy industry to use more costly resources such as roadside residue or bugwood. Government policies are also needed to support the long-term availability of biomass supplies in order to lower the supply risks related to the use of biomass resources in the energy industry. Lower prices for power in both provinces make the use of biomass unfavourable for small-scale technologies under 10 MW. However, cogeneration projects using biomass showed higher returns when power conversion efficiency was low. Higher revenues were generated from heat sales displacing natural gas than from electricity sales at current tariffs. Large-scale biomass power plants were viable when lower-cost feedstocks were available. Bio-oils were suitable as supplements for heat generation in cogeneration processes. Pellet production was also viable using less expensive feedstocks.The co-firing of biomass at coal plants required little capital investment. The study demonstrated that Alberta's power production incentive of $60 per MWh was sufficient to improve the economics of small-scale projects. It was recommended that the program be continued and paid out over a period of 10 years. It was concluded that specific electricity tariffs and incentives are needed to accelerate regrowth and create a viable biomass industry for the future. 33 refs., 45 tabs., 17 figs

Experimental investigation of combustion of biomass slurry in an oil fired furnace

Energy Technology Data Exchange (ETDEWEB)

Prakash, S.V. [Mechanical Dept., M.S. Ramaiah Inst. of Tech., Bangalore (India); Shankapal, S.R. [M.S. Ramaiah School of Advanced Studies, Bangalore (India)

2008-07-01

An experimental investigation of combustion of biomass slurry in an oil fired furnace was carried out using pulverized coconut shell (CSP), LDO and water. The effect of equivalence ratio on the slurry composition, calorific value and the effect of exhaust gas percentage are presented. The calorific value of the biomass slurry increases with equivalence ratio initially, attains a peak value and then decreases with the increase in equivalence ratio. It is also observed that with the increase in composition of biomass slurry, the cost of the fuel and the percentage emission of CO decreases. It was found that CSP up to a blend of 20% was more convenient to be used as a slurry fuel in the furnace. (orig.)

Socioeconomic Constraints to Biomass Removal from Forest Lands for Fire Risk Reduction in the Western U.S.

Directory of Open Access Journals (Sweden)

David L. Nicholls

2018-05-01

Full Text Available Many socioeconomic constraints exist for biomass removals from federal lands in the western U.S. We examine several issues of importance, including biomass supply chains and harvesting costs, innovative new uses for bioenergy products, and the policy framework in place to provide incentives for biomass use. Western states vary greatly in the extent and utilization of forest resources, the proportion of land under federal ownership, and community and stakeholder structure and dynamics. Our research—which focused on the socioeconomic factors associated with biomass removal, production, and use—identified several important trends. Long-term stewardship projects could play a role in influencing project economics while being conducive to private investment. State policies are likely to help guide the growth of biomass utilization for energy products. New markets and technologies, such as biofuels, for use in the aviation industry, torrefied wood, mobile pyrolysis, and wood coal cofiring could greatly change the landscape of biomass use. Social needs of residents in wildland urban interfaces will play an important role, especially in an era of megafires. All of these trends—including significant unknowns, like the volatile prices of fossil energy—are likely to affect the economics of biomass removal and use in western forests.

Biomass and species structure of the phytoplankton of an high mountain lake (Lake Paione Superiore, Central Alps, Italy

Directory of Open Access Journals (Sweden)

Roberta BETTINETTI

1999-08-01

Full Text Available In the framework of the EU MOLAR Project on “Measuring and modelling the dynamic response of remote mountain lake ecosystems to environmental change” a three whole-year study (1996-1998 on the composition and dynamics of phytoplankton community of the high mountain lake, acid sensitive Lago Paione Superiore (LPS was carried out. The data were analyzed and compared with those gathered during the years 1991-1993. The phytoplankton was made up by nanoplanktonic unicellular algae, the only exception being the colonial Dinobryon sertularia. Just four species, belonging to Chrysophyceae (Chromulina sp., Dinobryon sertularia and Mallomonas alveolata and to Dinophyceae (Gymnodinium sp. were important as biomass and density, and they were always present throughout the year. The prevalence of potentially mixotrophic species suggests an adaptive strategy to the low environmental concentrations of inorganic carbon and phosphorus. The seasonal variations of the total biomass were similar to those observed in the previous years. The total number of species has increased; this could be related with the recent increase of the pH and of the alkalinity.

Major Biomass Conference

Science.gov (United States)

Top Scientists, Industry and Government Leaders to Gather for Major Biomass Conference America, South America and Europe will focus on building a sustainable, profitable biomass business at the Third Biomass Conference of the Americas in Montreal. Scheduled presentations will cover all biomass

Development and delivery of a workshop methodology: planning for biomass power plant projects

Energy Technology Data Exchange (ETDEWEB)

Gray, A.J.; Delbridge, P.; Trevorrow, E.; Pile, C.

2001-07-01

This report gives details of the approach used to develop a workshop methodology to help planners and stakeholders address key issues that may arise when submitting a planning application for a biomass power plant in the light of the UK government's energy and climate change targets. The results of interviews with stakeholders (central government, regulatory authorities, developers, planners, non-governmental organisations, local community, resident groups) are summarised, and the NIMBY (not in my back yard) syndrome, the lack of trust in the developer, and lack of awareness of the use of biomass are discussed. Details are given of the design and testing of the workshop methodology and the resulting workshop methodology and workbook guide aimed at understanding the stakeholder issues and concerns through stakeholder discussions.

Anthropogenic Land-use Change and the Dynamics of Amazon Forest Biomass

Science.gov (United States)

Laurance, William F.

2004-01-01

This project was focused on assessing the effects of prevailing land uses, such as habitat fragmentation, selective logging, and fire, on biomass and carbon storage in Amazonian forests, and on the dynamics of carbon sequestration in regenerating forests. Ancillary goals included developing GIs models to help predict the future condition of Amazonian forests, and assessing the effects of anthropogenic climate change and ENS0 droughts on intact and fragmented forests. Ground-based studies using networks of permanent plots were linked with remote-sensing data (including Landsat TM and AVHRR) at regional scales, and higher-resolution techniques (IKONOS imagery, videography, LIDAR, aerial photographs) at landscape and local scales. The project s specific goals were quite eclectic and included: Determining the effects of habitat fragmentation on forest dynamics, floristic composition, and the various components of above- and below-ground biomass. Assessing historical and physical factors that affect trajectories of forest regeneration and carbon sequestration on abandoned lands. Extrapolating results from local studies of biomass dynamics in fragmented and regenerating forests to landscape and regional scales in Amazonia, using remote sensing and GIS. Testing the hypothesis that intact Amazonian forests are functioning as a significant carbon sink. Examining destructive synergisms between forest fragmentation and fire. Assessing the short-term impacts of selective logging on aboveground biomass. Developing GIS models that integrate current spatial data on forest cover, deforestation, logging, mining, highway and roads, navigable rivers, vulnerability to wild fires, protected areas, and existing and planned infrastructure projects, in an effort to predict the future condition of Brazilian Amazonian forests over the next 20-25 years. Devising predictive spatial models to assess the influence of varied biophysical and anthropogenic predictors on Amazonian deforestation.

LCA of domestic and centralized biomass combustion: The case of Lombardy (Italy)

International Nuclear Information System (INIS)

Caserini, S.; Livio, S.; Giugliano, M.; Grosso, M.; Rigamonti, L.

2010-01-01

This paper analyzes and compares the environmental impacts of biomass combustion in small appliances such as domestic open fireplaces and stoves, and in two types of centralized combined heat and power plants, feeding district heating networks. The analysis is carried out following a Life Cycle Assessment (LCA) approach. The expected savings of GHG (greenhouse gases) emissions due to the substitution of fossil fuels with biomass are quantified, as well as emissions of toxic pollutants and substances responsible for acidification and ozone formation. The LCA results show net savings of GHG emissions when using biomass instead of conventional fuels, varying from 0.08 to 1.08 t of CO 2 eq. per t of dry biomass in the different scenarios. Avoided GHG emissions thanks to biomass combustion in Lombardy are 1.32 Mt year -1 (1.5% of total regional GHG emissions). For the other impact categories, the use of biomass in district heating systems can again cause a consistent reduction of impacts, whereas biomass combustion in residential devices shows higher impacts than fossil fuels with a particular concern for PAH, VOC and particulate matter emissions. For example, in Lombardy, PM10 emissions from domestic devices are about 8100 t year -1 , corresponding to almost one third of the total particulate emissions in 2005. (author)

The determination of mercury content in the biomass untended for industrial power plant

Directory of Open Access Journals (Sweden)

Wiktor Magdalena

2017-01-01

Full Text Available Biomass is one of the oldest and most widely used renewable energy sources. The biomass is the whole organic matter of vegetable or animal origin which is biodegradable. Biomass includes leftovers from agricultural production, forestry residues, and industrial and municipal waste. The use of biomass in the power industry has become a standard and takes place in Poland and other European countries. This paper discusses the correlation of mercury content in different biomass types used in the power industry and in products of biomass combustion. Different biomass types, which are currently burned in a commercial power plant in Poland, were discussed. A photographic documentation of different biomass types, such as straw briquettes, wood briquettes, pellets from energy crops (sunflower husk and wood husk, wood pellets, wood chips, and agro-biomass (seeds was carried out. The presented paper discusses the results obtained for 15 biomass samples. Five selected biomass samples were burned in controlled conditions in the laboratory at the University of Silesia. The ash resulting from the combustion of five biomass samples was tested for mercury content. A total of twenty biomass samples and its combustion products were tested. Based on the obtained results, it was found that any supply of biomass, regardless of its type, is characterized by variable mercury content in dry matter. In the case of e.g. wood chips, the spread of results reaches 235.1 μm/kg (in dry matter. Meanwhile, the highest mercury content, 472.4 μm/kg (in dry matter was recorded in the biomass of straw, wood pellets, and pellets from energy crops (sunflower husk. In the case of combustion products of five selected biomass types, a three or four fold increase in the mercury content has been observed.

Biomass treatment method

Science.gov (United States)

Friend, Julie; Elander, Richard T.; Tucker, III; Melvin P.; Lyons, Robert C.

2010-10-26

A method for treating biomass was developed that uses an apparatus which moves a biomass and dilute aqueous ammonia mixture through reaction chambers without compaction. The apparatus moves the biomass using a non-compressing piston. The resulting treated biomass is saccharified to produce fermentable sugars.

Hydrogen Production Cost Estimate Using Biomass Gasification: Independent Review

Energy Technology Data Exchange (ETDEWEB)

Ruth, M.

2011-10-01

This independent review is the conclusion arrived at from data collection, document reviews, interviews and deliberation from December 2010 through April 2011 and the technical potential of Hydrogen Production Cost Estimate Using Biomass Gasification. The Panel reviewed the current H2A case (Version 2.12, Case 01D) for hydrogen production via biomass gasification and identified four principal components of hydrogen levelized cost: CapEx; feedstock costs; project financing structure; efficiency/hydrogen yield. The panel reexamined the assumptions around these components and arrived at new estimates and approaches that better reflect the current technology and business environments.

Power production from biomass III. Gasification and pyrolysis R and D and D for industry

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K.; Korhonen, M. [eds.] [VTT Energy, Espoo (Finland). New Energy Technologies

1999-07-01

The Seminar on Power Production from Biomass III. Gasification and Pyrolysis R and D and D for Industry, was held on 14-15 September 1998 in Espoo. The seminar was organised by VTT Energy in co-operation with the University of Groningen, EU-Thermie Programme and Technology Development Centre, Finland (Tekes). Overviews of current activities on power production from biomass and wastes in Europe and in the United States were given, and all European and U. S. demonstration projects on biomass gasification were presented. In Europe, the target is to produce additional 90 Mtoe/a of bioenergy for the market by 2010. This is a huge challenge for the bioenergy sector, including biomass production and harvesting, conversion technology, energy companies, and end users. In USA, U.S. Department of Energy is promoting the Biomass Power Programme to encourage and assist industry in the development and validation of renewable, biomass-based electricity generation systems, the objective being to double the present use of 7 000 MW biomass power by the year 2010. The new Finnish PROGAS Programme initiated by VTT was also introduced. Several gasification projects are today on the demonstration stage prior to entering the commercial level. Pyrolysis technologies are not yet on the demonstration stage on the energy market. Bio-oils can easily be transported, stored and utilised in existing boiler and diesel plants. The proceedings include the presentations given by the keynote speakers and other invited speakers, as well as some extended poster presentations. (orig.)

Electrocatalytic upgrading of biomass pyrolysis oils to chemical and fuel