Pulsed ion beam-assisted carburizing of titanium in methane discharge

International Nuclear Information System (INIS)

Shafiq, M.; Shahzad, K.; Zakaullah, M.; Hassan, M.; Qayyum, A.; Ahmad, S.; Rawat, R. S.

2010-01-01

The carburizing of titanium (Ti) is accomplished by utilizing energetic ion pulses of a 1.5 kJ Mather type dense plasma focus (DPF) device operated in methane discharge. X-ray diffraction (XRD) analysis confirms the deposition of polycrystalline titanium carbide (TiC). The samples carburized at lower axial and angular positions show an improved texture for a typical (200)TiC plane. The Williamson–Hall method is employed to estimate average crystallite size and microstrains in the carburized Ti surface. Crystallite size is found to vary from ∼ 50 to 100 nm, depending on the deposition parameters. Microstrains vary with the sample position and hence ion flux, and are converted from tensile to compressive by increasing the flux. The carburizing of Ti is confirmed by two major doublets extending from 300 to 390 cm −1 and from 560 to 620 cm −1 corresponding to acoustic and optical active modes in Raman spectra, respectively. Analyses by scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDS) have provided qualitative and quantitative profiles of the carburized surface. The Vickers microhardness of Ti is significantly improved after carburizing. (nuclear physics)

Examination of Electrical Resistance of Carburizers Used for Cast Iron Production

Directory of Open Access Journals (Sweden)

Książek D.

2016-12-01

Full Text Available The publication presents the results of examination of selected carburizers used for cast iron production with respect to their electric resistance. Both the synthetic graphite carburizers and petroleum coke (petcoke carburizers of various chemical composition were compared. The relationships between electrical resistance of tested carburizers and their quality were found. The graphite carburizers exhibited much better conductivity than the petcoke ones. Resistance characteristics were different for the different types of carburizers. The measurements were performed according to the authors’ own method based on recording the electric current flow through the compressed samples. The samples of the specified diameter were put under pressure of the gradually increased value (10, 20, 50, 60, and finally 70 bar, each time the corresponding value of electric resistance being measured with a gauge of high accuracy, equal to 0.1μΩ. The higher pressure values resulted in the lower values of resistance. The relation between both the thermal conductance and the electrical conductance (or the resistance is well known and mentioned in the professional literature. The results were analysed and presented both in tabular and, additionally, in graphic form.

Materials and Process Design for High-Temperature Carburizing: Integrating Processing and Performance

Energy Technology Data Exchange (ETDEWEB)

D. Apelian

2007-07-23

The objective of the project is to develop an integrated process for fast, high-temperature carburizing. The new process results in an order of magnitude reduction in cycle time compared to conventional carburizing and represents significant energy savings in addition to a corresponding reduction of scrap associated with distortion free carburizing steels.

EFFET DES TRAITEMENTS THERMIQUES SUR LA REACTION ENTRE DES COUCHES MINCES DE TITANE ET DES SUBSTRATS EN ACIER

Directory of Open Access Journals (Sweden)

D Slimani

2015-06-01

Full Text Available Des couches minces du titane pur ont été déposées avec la méthode de pulvérisation cathodique sur des substrats en acier, type FF80 K-1 contenants ~1% mass. en carbone. La réaction entre les deux parties du système substrat-couche mince est activée avec des traitements thermiques sous vide dans l’intervalle de températures de 400 à900°Cpendant 30 minutes. Les Spectres de diffraction de rayons x confirment l’inter- diffusion des éléments  chimiques du système résultants la formation et la croissance des nouvelles phases en particulier le carbure binaire TiC ayant des caractéristiques thermomécaniques importantes. L’analyse morphologique des échantillons traités  avec le microscope électronique à balayage (MEB montre l’augmentation du flux de diffusion atomique avec la température de recuit, notamment la diffusion du manganèse et du fer vers la surface libre des échantillons aux températures élevées provoquant la dégradation des propriétés mécaniques des revêtements contrairement au premiers stades d’interaction où on a obtenu des bonnes valeurs de la microdureté.

3d Simulation of Di Diesel Combustion and Pollutant Formation Using a Two-Component Reference Fuel Simulation 3D de la combustion et de la formation des polluants dans un moteur Diesel à injection directe en utilisant un carburant de référence à deux composants

Directory of Open Access Journals (Sweden)

Barths H.

2006-12-01

reference fuels. The contributions of the different reaction paths (thermal, prompt, nitrous, and reburn to the NO formation are shown. Finally, the importance of the mixing process for the prediction of soot emissions is discussed. En séparant calculs aérodynamiques et calculs chimiques, le modèle instationnaire de flamelet permet d'introduire des mécanismes chimiques complets qui comprennent plusieurs centaines de réactions. Ceci est indispensable pour décrire les différents processus qui ont lieu dans un moteur Diesel à injection directe (ID tels que l'auto-inflammation, la fin de la phase de prémélange partiel, la transition vers une combustion diffusive et la formation de polluants tels que les NOx et les suies. Il n'est pas nécessaire de simplifier les taux de réactions hautement non linéaires, d'autre part, la structure complète du processus de combustion est conservée. En utilisant le modèle de type Representative Interaction Flamelet (RIF, l'ensemble monodimensionnel instationnaire d'équations différentielles aux dérivées partielles est résolu en interaction avec le code CFD 3D. La solution ainsi obtenue est couplée avec les flux gazeux et le champ de mélange par l'intermédiaire de plusieurs paramètres dépendant du temps (l'enthalpie, la pression, le taux scalaire de dissipation. En retour, le modèle de flamelet fournit les concentrations moyennes des espèces chimiques, qui sont ensuite exploitées par le code CFD 3D pour calculer les champs de températures et les densités. La densité est nécessaire au code CFD 3D pour déterminer les flux turbulents et le champ de mélange. La formation des polluants est déterminée expérimentalement dans un moteur Diesel Volkswagen DI 1900. Le moteur est alimenté avec du gazole et deux carburants de référence. Un des carburants de référence est du n-décane pur. Le second est un carburant bicomposant formé de 70 % (du volume liquide de n-décane et de 30 % d'alpha-méthylnaphtalène (Idea

Utilisation de produits organiques oxygénés comme carburants et combustibles dans les moteurs. Deuxième partie : Les différentes filières d'obtention des carburols. Analyse technico-économique Using Oxygenated Organic Products As Fuels in Engines. Part Two: Different Systems for Producing Alcohol Fuels. Technico-Economic Analysis

Directory of Open Access Journals (Sweden)

Chauvel A.

2006-11-01

Full Text Available Parmi les produits à même d'être substitués aux hydrocarbures pour la constitution des carburants, les composés organiques oxygénés occupent une place prépondérante à cause de leurs caractéristiques favorables à la combustion dans les moteurs, qu'ils soient employés purs ou mélangés (seuls ou à plusieurs aux hydrocarbures, constituants des carburants classiques. Dans cet article, ces composés oxygénés sont désignés sous le nom de carburols. Alors que l'objet de la première partie de l'étude a été d'examiner les conséquences techniques de l'emploi de ces produits sur les circuits de distribution et le fonctionnement des véhicules, il s'agit dans la présente partie d'analyser les caractéristiques technico-économiques de leur fabrication. En particulier, on y aborde successivement les points suivants : - disponibilités en matières premières : ressources fossiles et végétales ; - analyse technique des divers modes d'obtention - analyse économique ; - programmes nationaux. Among products that can be substituted for hydrocarbons for producing fuels, oxygenated organic compounds occupy a preponderant position because of their favorable characteristics for combustion in engines whether they are used in a pure form or in mixtures (alone or severally with hydrocarbons which are used to make up conventional fuels. In this article these oxygenated compounds are given the name carburols (alcohol fuels. Whereas the aim of Part 1 was to examine the technical consequences of using such products in distribution circuits and for vehicle operating, Part 2 is an analysis of the technico-economic aspects of manufacturing them. In particular, the following points are taken up successively: (a availabilities of raw materials. fossil and vegetebal resources; (b technical analysis of various production methods; (c economic analysis; (d national programs. Depending on the amounts involved, a distinction is made among alternative

Characteristic of Low Temperature Carburized Austenitic Stainless Steel

Science.gov (United States)

Istiroyah; Pamungkas, M. A.; Saroja, G.; Ghufron, M.; Juwono, A. M.

2018-01-01

Low temperature carburizing process has been carried out on austenitic stainless steel (ASS) type AISI 316L, that contain chromium in above 12 at%. Therefore, conventional heat treatment processes that are usually carried out at high temperatures are not applicable. The sensitization process due to chromium migration from the grain boundary will lead to stress corrosion crack and decrease the corrosion resistance of the steel. In this study, the carburizing process was carried out at low temperatures below 500 °C. Surface morphology and mechanical properties of carburized specimens were investigated using optical microscopy, non destructive profilometer, and Vicker microhardness. The surface roughness analysis show the carburising process improves the roughness of ASS surface. This improvement is due to the adsorption of carbon atoms on the surface of the specimen. Likewise, the hardness test results indicate the carburising process increases the hardness of ASS.

Sustainable Steel Carburization by Using Snack Packaging Plastic Waste as Carbon Resources

Directory of Open Access Journals (Sweden)

Songyan Yin

2018-01-01

Full Text Available In recent years, the research regarding waste conversion to resources technology has attracted growing attention with the continued increase of waste accumulation issues and rapid depletion of natural resources. However, the study, with respect to utilizing plastics waste as carbon resources in the metals industry, is still limited. In this work, an environmentally friendly approach to utilize snack packaging plastic waste as a valuable carbon resources for steel carburization is investigated. At high temperature, plastic waste could be subject to pyrolytic gasification and decompose into small molecular hydrocarbon gaseous products which have the potential to be used as carburization agents for steel. When heating some snack packaging plastic waste and a steel sample together at the carburization temperature, a considerable amount of carbon-rich reducing gases, like methane, could be liberated from the plastic waste and absorbed by the steel sample as a carbon precursor for carburization. The resulting carburization effect on steel was investigated by optical microscopy, scanning electron microscopy, electron probe microanalyzer, and X-ray photoelectron spectrometer techniques. These investigation results all showed that snack packaging plastic waste could work effectively as a valuable carbon resource for steel carburization leading to a significant increase of surface carbon content and the corresponding microstructure evolution in steel.

Fuel Penalty Comparison for (Electrically Heated Catalyst Technology Comparaison de l’augmentation de consommation de carburant pour la technologie de catalyseurs chauffés à l’électricité

Directory of Open Access Journals (Sweden)

Kessels J. T.B.A.

2010-03-01

Full Text Available The conversion efficiency of three way catalytic converters is mainly defined by the temperature range wherein they are operating. Traditionally, ignition retard has been used to reduce the light-off time of the catalyst. This is however associated with a fuel penalty. With increasing vehicle electrification, electrically heating facilities present an alternative, especially for hybrid vehicles. Nevertheless, system complexity of hybrid vehicles prevents engineers to evaluate possible heating technologies and their corresponding fuel penalty with respect to traditional solutions. This paper evaluates the application of an electrically heated catalyst on a hybrid vehicle equipped with a Natural Gas (NG engine. The effect of heating power on light-off time and fuel penalty is determined, using analysis techniques emerging from integrated powertrain control. By means of a case study, the importance of an integral approach is explained by comparing the fuel penalty and conversion efficiency improvement of electric heating with that of ignition retard. In this process, a mix of simulation and test data were combined, forming the foundations for future control developments of a suitable light-off strategy. L’efficacité de conversion des catalyseurs est principalement définie par la gamme de température dans laquelle ils fonctionnent. Un retard du point d’allumage a traditionnellement été utilisé pour réduire le temps d’amorçage du catalyseur. Ceci est cependant associé à une augmentation de la consommation de carburant. Avec l’électrification des véhicules, la possibilité de chauffage électrique représente véritablement une alternative, tout particulièrement pour les véhicules hybrides. Cependant, la complexité des véhicules hybrides rend difficile l’évaluation des technologies de chauffage éventuelles ainsi que l’augmentation de la consommation de carburant associée ; il est aussi difficile de comparer ces r

The sort of carburization and the quality of obtained cast iron

Directory of Open Access Journals (Sweden)

K. Janerka

2008-12-01

Full Text Available In the production of cast iron, the pig iron’s amount in charge material is more and more often limited, and replaced by steel scrap. That extorts the necessity of know-how the carburization and one is looking for carburizers, which ensure obtaining big carbon increment as quickly as possible with the high repeatability and the ones which ensure getting the adequate quality of cast iron. The object of presented research was definition of the influence of charge materials’ sort on the structure, course of solidification, and the effectiveness of process. The cast iron melts, which are presented below, are made only on the basis of steel scrap with portion of graphitoidal, coke and anthracite carburizers, which were added to the charge in solid. In the article one compared the carburizers in respect of their structure, chemical constitution and the effectiveness obtained during the carburization of liquid metal. The melting of cast iron, based on the special pig iron, was carried out as well. The course of melts, chemical constitution of obtained cast iron and its structure were presented. The comparison between quality distribution and the volume fraction of graphite in classes of size for the individual melts were achieved and the TDA curves were inserted.

Plasma carburizing with surface micro-melting

Science.gov (United States)

Balanovsky, A. E.; Grechneva, M. V.; Van Huy, Vu; Ponomarev, B. B.

2018-03-01

This paper presents carburizing the surface of 20 low carbon steel using electric arc and graphite prior. A carbon black solution was prepared with graphite powder and sodium silicate in water. A detailed analysis of the phase structure and the distribution profile of the sample hardness after plasma treatment were given. The hardened layer consists of three different zones: 1 – the cemented layer (thin white zone) on the surface, 2 – heat-affected zone (darkly etching structure), 3 – the base metal. The experimental result shows that the various microstructures and micro-hardness profiles were produced depending on the type of graphite coating (percentage of liquid glass) and processing parameters. The experiment proved that the optimum content of liquid glass in graphite coating is 50–87.5%. If the amount of liquid glass is less than 50%, adhesion to metal is insufficient. If liquid glass content is more than 87.5%, carburization of a metal surface does not occur. A mixture of the eutectic lamellar structure, martensite and austenite was obtained by using graphite prior with 67% sodium silicate and the levels of the hardness layer increased to around 1000 HV. The thickness of the cemented layer formed on the surface was around 200 μm. It is hoped that this plasma surface carburizing treatment could improve the tribological resistance properties.

Pulverization of boron element and proportions of boron carbide in boron; Broyage de bore element et dosage de carbure de bore dans le bore

Energy Technology Data Exchange (ETDEWEB)

Lang, F M; Finck, C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1956-07-01

It is possible to reduce boron element into fine powder by means of a mortar and pestle made of sintered boron carbide, the ratio of boron carbide introduced being less than one per cent. Boron element at our disposal is made of sharp edged, dark brown, little grains of average size greater than 5 {mu}. Grain sizes smaller than 1{mu} are required for applying thin layers of such boron. (author) [French] Il est possible de pulveriser finement du bore element au moyen de mortier et pilon en carbure de bore fritte, le taux de carbure de bore introduit etant inferieur a 1 pour cent. Le bore element dont nous disposons est constitue de petits grains brun fonce, a aretes vives, de dimension moyenne superieure a 5 {mu}. L'application de ce bore en couches minces demande des grains de dimensions inferieures a 1 {mu}. (aute0008.

Acetylene Flow Rate as a Crucial Parameter of Vacuum Carburizing Process of Modern Tool Steels

Directory of Open Access Journals (Sweden)

Rokicki P.

2016-12-01

Full Text Available Carburizing is one of the most popular and wide used thermo-chemical treatment methods of surface modification of tool steels. It is a process based on carbon diffusive enrichment of the surface material and is applied for elements that are supposed to present higher hardness and wear resistance sustaining core ductility. Typical elements submitted to carburizing process are gears, shafts, pins and bearing elements. In the last years, more and more popular, especially in highly advanced treatment procedures used in the aerospace industry is vacuum carburizing. It is a process based on chemical treatment of the surface in lower pressure, providing much higher uniformity of carburized layer, lower process cost and much lesser negative impact on environment to compare with conventional carburizing methods, as for example gas carburizing in Endo atmosphere. Unfortunately, aerospace industry requires much more detailed description of the phenomena linked to this process method and the literature background shows lack of tests that could confirm fulfilment of all needed requirements and to understand the process itself in much deeper meaning. In the presented paper, authors focused their research on acetylene flow impact on carburized layer characteristic. This is one of the most crucial parameters concerning homogeneity and uniformity of carburized layer properties. That is why, specific process methodology have been planned based on different acetylene flow values, and the surface layer of the steel gears have been investigated in meaning to impact on any possible change in potential properties of the final product.

Contribution to the study of U-Ti and U-Pu-Ti carbides; Contribution a l'etude des carbures U-C-Ti et (U, Pu) - C-Ti

Energy Technology Data Exchange (ETDEWEB)

Milet, C A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

After having discussed the reasons to use (U,Pu) carbides as fast reactor fuel, we examine the influence of the addition of titanium to these carbides. A preliminary study has been done on the system of U-C-Ti and some properties have been measured such as: density, thermal expansion, electrical resistivity, atmospheric corrosion and compatibility with stainless steel. The systems U-Pu-C-Ti (Pu/U + Pu equal to 15 per cent) and U-C-Ti have been found to be very similar. There exists a two phases region (U,Pu)C + TiC, an eutectic between (U,Pu)C and TiC for approximately 15 at %. The solubilities of U + Pu in TiC and of Ti in (U,Pu)C is less than 1 % at. The addition of titanium does not markedly change thermal expansion coefficients of (U,Pu)C. However the resistance to atmospheric corrosion and compatibility with stainless steel is improved. Thermal conductivity, calculated from electrical resistivity, has increased. On the other side, the density of fissile material is lowered. The combination of (U,Pu)C + TiC seems to be the most promising alloy for application as nuclear fuel. (author) [French] Apres avoir rappele les problemes poses par un combustible pour les reacteurs a neutrons rapides et l'interet des carbures U-Pu-C comme combustible, on examine l'influence de l'addition de titane dans ces carbures. Une etude preliminaire sur le systeme U-C-Ti a ete effectuee et quelques proprietes sont indiquees: densite, coefficients de dilatation, resistivite electrique, tenue a la corrosion atmospherique, compatibilite avec l'acier inoxydable. Le systeme U-Pu-C-Ti (Pu/U + Pu egal a 15 pour cent) presente de grandes analogies avec le systeme U-C-Ti. Il existe un domaine biphase (U,Pu)C + TiC, un eutectique entre (U,Pu)C et TiC pour environ 15 at % Ti; les solubilites de U + Pu clans TiC et de Ti dans (U,Pu)C sont inferieures a 1 at %. Par rapport a la phase (U,Pu)C, l'addition de titane est sans effets importants sur les coefficients de dilatation. Par contre la tenue a

Carburization of austenitic alloys by gaseous impurities in helium

International Nuclear Information System (INIS)

Lai, G.Y.; Johnson, W.R.

1980-03-01

The carburization behavior of Alloy 800H, Inconel Alloy 617 and Hastelloy Alloy X in helium containing various amounts of H 2 , CO, CH 4 , H 2 O and CO 2 was studied. Corrosion tests were conducted in a temperature range from 649 to 1000 0 C (1200 to 1832 0 F) for exposure time up to 10,000 h. Four different helium environments, identified as A, B, C, and D, were investigated. Concentrations of gaseous impurities were 1500 μatm H 2 , 450 μatm CO, 50 μatm CH 4 and 50 μatm H 2 O for Environment A; 200 μatm H 2 , 100 μatm CO, 20 μatm CH 4 , 50 μatm H 2 O and 5 μatm CO 2 for Environment B; 500 μatm H 2 , 50 μatm CO, 50 μatm CH 4 and 2 O for Environment C; and 500 μatm H 2 , 50 μatm CO, 50 μatm CH 4 and 1.5 μatm H 2 O for Environment D. Environments A and B were characteristic of high-oxygen potential, while C and D were characteristic of low-oxygen potential. The results showed that the carburization kinetics in low-oxygen potential environments (C and D) were significantly higher, approximately an order of magnitude higher at high temperatures, than those in high-oxygen potential environments (A and B) for all three alloys. Thermodynamic analyses indicated no significant differences in the thermodynamic carburization potential between low- and high-oxygen potential environments. It is thus believed that the enhanced carburization kinetics observed in the low-oxygen potential environments were related to kinetic effects. A qualitatively mechanistic model was proposed to explain the enhanced kinetics. The present results further suggest that controlling the oxygen potential of the service environment can be an effective means of reducing carburization of alloys

Creep properties of Hastelloy X in a carburizing helium environment

International Nuclear Information System (INIS)

Nakanishi, T.; Kawakami, H.

1982-01-01

In this work, we investigate the environmental effect on the creep behavior of Hastelloy X at 900 0 C in helium and air. Since helium coolant in HTGR is expected to be carburizing and very weakly oxidizing for most metals, testings were focused on the effect of carburizing and slight oxidation. Carburization decreases secondary creep strain rate and delays tertiary creep initiation. On the other hand, the crack growth rate on the specimen surface is enhanced due to very weak oxidation in helium, therefore the tertiary creep strain rate becomes larger than that in air. The rupture time of Hastelloy X was shorter in helium when compared with in air. Stress versus rupture time curves for both environments do not deviate with each other during up to 5000 hours test, and a ratio of rupture stress in helium to that in air was about 0.9

Existence and structure of rare-earth mono-carbides: study of their low-temperature magnetic properties; Existence et structure des monocarbures de terres rares. Etude de leurs proprietes magnetiques a basses temperatures

Energy Technology Data Exchange (ETDEWEB)

Lallement, R [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Fontenay-aux-Roses, 92 (France)

1966-07-01

There are two types of rare earth carbides, the first one is face-centered cubic, stable at high temperature, and very hypo-stoichiometric (formula MC{sub x} with 0.35 < x < 0.65); the other is rhombohedric, stable at lower temperature, with a formula M{sub 2}C. These two carbides are magnetically ordered at low temperatures (ferro or ferri-magnetism). They are highly anisotropic. A great part of the electric and magnetic properties can be explained from the following ideas: the M{sup 3+} ions are coupled via the conduction electrons, there are more conduction electrons in the carbides than in the metals, and there is some local order around the transition temperatures. (author) [French] Nous avons mis en evidence l'existence de deux carbures de terres rares, l'un de formule MC{sub x} (0,35 < x < 0,65) de structure cubique a faces centrees, stable a haute temperature, l'autre de formule M{sub 2}C, de structure rhomhoedrique, stable a temperature moyenne. Ces deux types de carbures presentent des phenomenes d'ordre magnetique a basses temperatures (ferro ou ferrimagnetisme). Ils sont caracterises par une forte anisotropie magnetique. Une grande partie des proprietes electriques et magnetiques s'explique a partir des hypotheses suivantes: a) Les ions M{sup 3+} sont couples entre eux par l'intermediaire des electrons de conduction; b) Le nombre d'electrons de conduction dans les carbures est plus grand que dans les metaux; c) Autour des temperatures de transition se manifestent des phenomenes d'ordre local. (auteur)

Rolling Contact Fatigue Performances of Carburized and High-C Nanostructured Bainitic Steels

Directory of Open Access Journals (Sweden)

Yanhui Wang

2016-11-01

Full Text Available In the present work, the nanostructured bainitic microstructures were obtained at the surfaces of a carburized steel and a high-C steel. The rolling contact fatigue (RCF performances of the two alloy steels with the same volume fraction of undissolved carbide were studied under lubrication. Results show that the RCF life of the carburized nanostructured bainitic steel is superior to that of the high-C nanostructured bainitic steel in spite of the chemical composition, phase constituent, plate thickness of bainitic ferrite, hardness, and residual compressive stress value of the contact surfaces of the two steels under roughly similar conditions. The excellent RCF performance of the carburized nanostructured bainitic steel is mainly attributed to the following reasons: finer carbide dispersion distribution in the top surface, the higher residual compressive stress values in the carburized layer, the deeper residual compressive stress layer, the higher work hardening ability, the larger amount of retained austenite transforming into martensite at the surface and the more stable untransformed retained austenite left in the top surface of the steel.

Rolling Contact Fatigue Performances of Carburized and High-C Nanostructured Bainitic Steels.

Science.gov (United States)

Wang, Yanhui; Zhang, Fucheng; Yang, Zhinan; Lv, Bo; Zheng, Chunlei

2016-11-25

In the present work, the nanostructured bainitic microstructures were obtained at the surfaces of a carburized steel and a high-C steel. The rolling contact fatigue (RCF) performances of the two alloy steels with the same volume fraction of undissolved carbide were studied under lubrication. Results show that the RCF life of the carburized nanostructured bainitic steel is superior to that of the high-C nanostructured bainitic steel in spite of the chemical composition, phase constituent, plate thickness of bainitic ferrite, hardness, and residual compressive stress value of the contact surfaces of the two steels under roughly similar conditions. The excellent RCF performance of the carburized nanostructured bainitic steel is mainly attributed to the following reasons: finer carbide dispersion distribution in the top surface, the higher residual compressive stress values in the carburized layer, the deeper residual compressive stress layer, the higher work hardening ability, the larger amount of retained austenite transforming into martensite at the surface and the more stable untransformed retained austenite left in the top surface of the steel.

Cluster carburizing. Final report, June 1, 1973-May 31, 1979

International Nuclear Information System (INIS)

Morral, J.E.

1979-05-01

Three major accomplishments of the cluster carburizing program were showing that the hardness of aged and carburized materials could be controlled via the aged structure; developing a new and analytical theory of subscale formation; and characterizing the properties of Ta-Hf alloys with respect to precipitation kinetics and morphology, diffusion kinetics, age hardening, and subscale formation. The first of these verified the cluster carburizing concept, which has potential use in the development of high strength materials. The second has applications in the fields of hot corrosion, oxidation, and high temperature coatings. The third provided necessary background for this study and provided a further understanding of the behavior of refractory metals. Details about the above are contained in this final report as well as comments on the Ta-Hf, TaC-HfC and NbC-HfC phase diagrams, a comparison of hardening in the Nb-Hf and Ta-Hf system, and a discussion of possible future work

Surface modification of superaustenitic and maraging stainless steels by low-temperature gas-phase carburization

Science.gov (United States)

Gentil, Johannes

Low-temperature gas-phase carburization of 316L austenitic stainless steel was developed in recent years by the Swagelok company. This process generates great mechanical and electrochemical surface properties. Hardness, wear resistance, fatigue behavior, and corrosion resistance are dramatically improved, while the formation of carbides is effectively suppressed. This new technique is of technical, economical, but especially of scientific interest because the surface properties of common stainless steel can be enhanced to a level of more sophisticated and more expensive superalloys. The consequential continuation of previous research is the application of the carburization process to other steel grades. Differences in chemical composition, microstructure, and passivity between the various alloys may cause technical problems and it is expected that the initial process needs to be optimized for every specific material. This study presents results of low-temperature carburization of AL-6XN (superaustenitic stainless steel) and PH13-8Mo (precipitation-hardened martensitic stainless steel). Both alloys have been treated successfully in terms of creating a hardened surface by introducing high amounts of interstitially dissolved carbon. The surface hardness of AL-6XN was increased to 12GPa and is correlated with a colossal carbon supersaturation at the surface of up to 20 at.%. The hardened case develops a carburization time-dependent thickness between 10mum after one carburization cycle and up to 35mum after four treatments and remains highly ductile. Substantial broadening of X-ray diffraction peaks in low-temperature carburized superaustenitic stainless steels are attributed to the generation of very large compressive biaxial residual stresses. Those large stresses presumably cause relaxations of the surface, so-called undulations. Heavily expanded regions of carburized AL-6XN turn ferromagnetic. Non-carburized AL-6XN is known for its outstanding corrosion resistance

The formation of structures and properties of carburized elements and hardened in different quenching medium

International Nuclear Information System (INIS)

Przylecka, M.; Gestwa, W.

2003-01-01

In work structure and selected properties of hardened carburized layers were introduced produced on chromium-manganese steel (16HG - 16CrMn5), after processes of gas carburizing (850 o C/1-10 h) and vacuum carburizing (950 o C/2 h) as well as direct hardening (center cooling: distillated water, Water polymer solution - polyglycol oxyalkylen, oil and gas-nitrogen) and tempering. Results of investigations permitted to affirm, that layer with structure martensite - retained austenite, as carbides - martensite - retained austenite produced in process of hardening applying cooling centre water polymer solution, the impact strength of element (at define thickness of carburized layer) give profitable, suitable hardness and microhardness as well as changes of microhardness on section in comparison to produced layers during cooling in water or oil and gas. (author)

The effect of variations in carbon activity on the carburization of austenitic steels in sodium

International Nuclear Information System (INIS)

Gwyther, J.R.; Hobdell, M.R.; Hooper, A.J.

1978-07-01

Experience has shown that the liquid sodium coolant of fast breeder reactors is an effective carbon-transport medium; the resulting carburization of thin austenitic stainless steel components (eg IHX and fuel cladding) could adversely affect their mechanical integrity. The degree and nature of steel carburization depend, inter alia, on the carbon activity of the sodium environment. Exploratory tests are described in which specimens of austenitic stainless steel were carburized in sodium, the carbon activity of which was continuously monitored by a BNL electrochemical carbon meter. The sodium carbon activity was initially high, but decreased with time, simulating conditions equivalent to plant start-up or coolant clean-up following accidental oil ingress. The extent and nature of steel carburization was identified by metallography, electron microscopy, X-ray crystallography and chemical analysis. (author)

Alimentation des moteurs en mélange homogène pauvre Feeding Homogeneous Lean Mixtures to Engines

Directory of Open Access Journals (Sweden)

Rayna B.

2006-11-01

Full Text Available Les études effectuées dans le cadre de plusieurs conventions de recherche entre l'Institut de Recherche des Transports (IRT et l'Institut Français du Pétrole (IFP associé à d'autres organismes industriels (Régie Nationale des Usines Renault (RNUR, Solex... ont permis a de caractériser l'influence de la préparation physique du mélange air-carburant sur le fonctionnement de moteurs monocylindre et multicylindre. L'effet sur le rendement d'inégalités de richesse entre les cylindres a été estimé à l'aide d'un modèle mathématique de simulation du moteur à allumage commandé ; b d'analyser les défauts inhérents à certains systèmes d'alimentation actuels et d'expérimenter des techniques différentes de formation du mélange carburé (car-burateur à dépression constante, pulvérisation pneumatique du carburant. Les résultats obtenus ont montré notamment que des améliorations ne peuvent résulter que d'un aménagement d'ensemble de tous les éléments du circuit d'admission Investigations carried out under thé terms of several research agreements involving Institut de Recherche des Transports (IRT and Institut Français du Pétrole (IFP associated with other industrial organizations (Régie Nationale des Usines Renault (RNUR, Solex served ta a Characterize thé influence of thé physical preparation of thé air/fuel mixture on thé operating of single-cylinder and multicylinder engines. The effect on thé efficiency of unequal air/fuel ratios among thé cylindres was evaluated by a mathematical model used ta simulate a spark-ignition engine. b Analyze thé inhérent defects of some fuel-supply systems now used and ta experiment with différent techniques of mixture preparation (constant depression car-burettor, pneumatic fuel spraying. The results obtained show, in particulor, that improvements con be produced only by redesigning all thé parts of thé fuel-supply circuit.

Response of cast austenitic stainless steel to low temperature plasma carburizing.

OpenAIRE

Sun, Yong

2008-01-01

The response of a cast 316 type austenitic stainless steel to the novel low temperature plasma carburizing process has been investigated in this work. The cast steel has a dendritic structure with a mix of austenite, ferrite and carbide phases. The results show that such a complex structure responds well to the carburizing process, and the inter-dendrite regions containing ferrite and carbides can be transformed to expanded austenite to form a continuous and uniform layer supersat...

Paraequilibrium Carburization of Duplex and Ferritic Stainless Steels

Science.gov (United States)

Michal, G. M.; Gu, X.; Jennings, W. D.; Kahn, H.; Ernst, F.; Heuer, A. H.

2009-08-01

AISI 301 and E-BRITE stainless steels were subjected to low-temperature (743 K) carburization experiments using a commercial technology developed for carburization of 316 austenitic stainless steels. The AISI 301 steel contained ~40 vol pct ferrite before carburization but had a fully austenitic hardened case, ~20- μm thick, and a surface carbon concentration of ~8 at. pct after treatment; this “colossal” paraequilibrium carbon supersaturation caused an increase in lattice parameter of ~3 pct. The E-BRITE also developed a hardened case, 12- to 18- μm thick, but underwent a more modest (~0.3 pct) increase in lattice parameter; the surface carbon concentration was ~10 at. pct. While the hardened case on the AISI 301 stainless steel appeared to be single-phase austenite, evidence for carbide formation was apparent in X-ray diffractometer (XRD) scans of the E-BRITE. Paraequilibrium phase diagrams were calculated for both AISI 301 and E-BRITE stainless steels using a CALPHAD compound energy-based interstitial solid solution model. In the low-temperature regime of interest, and based upon measured paraequilibrium carbon solubilities, more negative Cr-carbon interaction parameters for austenite than those in the current CALPHAD data base may be appropriate. A sensitivity analysis involving Cr-carbon interaction parameters for ferrite found a strong dependence of carbon solubility on relatively small changes in the magnitude of these parameters.

Internal residual strain mapping in carburized chrome molybdenum steel after quenching by neutron strain scanning

International Nuclear Information System (INIS)

Sakaida, Yoshihisa; Serizawa, Takanobu; Manzanka, Michiya

2011-01-01

A hollow circular cylinder specimen with an annular U-notch of chrome molybdenum steel with 0.20 mass% C (SCM420) was carburized in carrier gas and quenched in oil bath. In order to determine the case depth, the specimen was cut off and carbon content and Vickers hardness gradients were measured experimentally near the carburized surface. The residual strain mapping in the interior of carburized cylinder was conducted nondestructively by neutron strain scanning. In this study, the neutron diffraction from Fe-211 plane was used for strain scanning. The neutron wavelength was tuned to 0.1654nm so that diffraction angle became about 90deg. Radial, hoop and axial residual strains were measured by scanning diffracting volume along the axial direction of cylinder specimen. Each residual strain was calculated from lattice spacing change. Unstressed lattice spacing was determined experimentally using reference coupon specimens that were cut from the interior of same carburized cylinder. As a result, the diffraction peak width at half height, FWHM, near the carburized surface was about 3.7 times wider than that of coupon specimens. On the other hand, the most peak widths in the interior equaled to that of coupon specimens. Peak width broadened slightly as the diffracting volume approached the carburized case layer. From the center to the quarter of cylinder specimen, the hoop and axial strains were tensile, and the radial one was compressive in the interior. From the quarter to the edge of the cylinder specimen, the hoop tensile strain increased, radial and axial strains changed to tensile and compressive, respectively. Therefore, the interior of the cylinder specimen was found to be deformed elastically to balance the existence of compressive residual stresses in the carburized case layer. (author)

Surface composition of carburized tungsten trioxide and its catalytic activity

International Nuclear Information System (INIS)

Nakazawa, M.; Okamoto, H.

1985-01-01

The surface composition and electronic structure of carburized tungsten trioxide are investigated using x-ray photoelectron spectroscopy (XPS). The relationship between the surface composition and the catalytic activity for methanol electro-oxidation is clarified. The tungsten carbide concentration in the surface layer increases with the carburization time. The formation of tungsten carbide enhances the catalytic activity. On the other hand, the presence of free carbon or tungsten trioxide in the surface layer reduces the activity remarkably. It is also shown that, the higher the electronic density of states near the Fermi level, the higher the catalytic activity

Optimisation des trajectoires verticales par la methode de la recherche de l'harmonie =

Science.gov (United States)

Ruby, Margaux

Face au rechauffement climatique, les besoins de trouver des solutions pour reduire les emissions de CO2 sont urgentes. L'optimisation des trajectoires est un des moyens pour reduire la consommation de carburant lors d'un vol. Afin de determiner la trajectoire optimale de l'avion, differents algorithmes ont ete developpes. Le but de ces algorithmes est de reduire au maximum le cout total d'un vol d'un avion qui est directement lie a la consommation de carburant et au temps de vol. Un autre parametre, nomme l'indice de cout est considere dans la definition du cout de vol. La consommation de carburant est fournie via des donnees de performances pour chaque phase de vol. Dans le cas de ce memoire, les phases d'un vol complet, soit, une phase de montee, une phase de croisiere et une phase de descente, sont etudies. Des " marches de montee " etaient definies comme des montees de 2 000ft lors de la phase de croisiere sont egalement etudiees. L'algorithme developpe lors de ce memoire est un metaheuristique, nomme la recherche de l'harmonie, qui, concilie deux types de recherches : la recherche locale et la recherche basee sur une population. Cet algorithme se base sur l'observation des musiciens lors d'un concert, ou plus exactement sur la capacite de la musique a trouver sa meilleure harmonie, soit, en termes d'optimisation, le plus bas cout. Differentes donnees d'entrees comme le poids de l'avion, la destination, la vitesse de l'avion initiale et le nombre d'iterations doivent etre, entre autre, fournies a l'algorithme pour qu'il soit capable de determiner la solution optimale qui est definie comme : [Vitesse de montee, Altitude, Vitesse de croisiere, Vitesse de descente]. L'algorithme a ete developpe a l'aide du logiciel MATLAB et teste pour plusieurs destinations et plusieurs poids pour un seul type d'avion. Pour la validation, les resultats obtenus par cet algorithme ont ete compares dans un premier temps aux resultats obtenus suite a une recherche exhaustive qui a

Carburization behavior of AISI 316LN austenitic stainless steel - Experimental studies and modeling

Energy Technology Data Exchange (ETDEWEB)

Sudha, C. [Physical Metallurgy Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); Sivai Bharasi, N. [Corrosion Science and Technology Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); Anand, R. [Physical Metallurgy Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); Shaikh, H., E-mail: hasan@igcar.gov.i [Corrosion Science and Technology Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); Dayal, R.K. [Corrosion Science and Technology Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India); Vijayalakshmi, M. [Physical Metallurgy Division, Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India)

2010-07-31

AISI type 316LN austenitic stainless steel was exposed to flowing sodium at 798 K for 16,000 h in the bi-metallic (BIM) sodium loop. A modified surface layer of 10 {mu}m width having a ferrite structure was detected from X-ray diffraction and electron micro probe based analysis. Beneath the modified surface layer a carburized zone of 60 {mu}m width was identified which was found to consist of M{sub 23}C{sub 6} carbides. A mathematical model based on finite difference technique was developed to predict the carburization profiles in sodium exposed austenitic stainless steel. In the computation, effect of only chromium on carbon diffusion was considered. Amount of carbon remaining in solution was determined from the solubility parameter. The predicted profile showed a reasonably good match with the experimental profile. Calculations were extended to simulate the thickness of the carburized layer after exposure to sodium for a period of 40 years. Attempt was also made to predict the carburization profiles based on equilibrium calculations using Dictra and Thermocalc which contain both thermodynamic and kinetic databases for the system under consideration.

Rolling Contact Fatigue Performances of Carburized and High-C Nanostructured Bainitic Steels

OpenAIRE

Wang, Yanhui; Zhang, Fucheng; Yang, Zhinan; Lv, Bo; Zheng, Chunlei

2016-01-01

In the present work, the nanostructured bainitic microstructures were obtained at the surfaces of a carburized steel and a high-C steel. The rolling contact fatigue (RCF) performances of the two alloy steels with the same volume fraction of undissolved carbide were studied under lubrication. Results show that the RCF life of the carburized nanostructured bainitic steel is superior to that of the high-C nanostructured bainitic steel in spite of the chemical composition, phase constituent, plat...

Carburants de substitution : orientations et recherches françaises Synthetic Fuels: French Orientation and Research

Directory of Open Access Journals (Sweden)

Guibet J. C.

2006-11-01

Full Text Available Le programme d'études et de recherches entrepris en France, depuis 1981, dans le domaine des carburants de substitution, porte à la fois sur l'examen des techniques d'obtention et sur les modalités d'utilisation de ces produits. Les travaux concernent essentiellement le méthanol, le système acétono-butylique et, pour les moteurs Diesel, les dérivés d'huiles végétales. On prévoit, dans une première phase, l'incorporation de faibles proportions - moins de 10 % - de produits organiques oxygénés dans le supercarburant sans modifier les spécifications du produit ni les conditions de réglage des véhicules. D'autres études sont effectuées sur des mélanges à teneur moyenne ou élevée en méthanol (30, 50 ou 90 % afin d'examiner les meilleures voies possibles pour une substitution plus importante. The research undertaken in France since 1981 in the field of alternative fuels includes both the ways of producing and the ways of using such products. These research projects mainly concern methanol, butanol-acetone system and, for diesel engines, vegetable-oil derivatives. In the first phase, plans are being made to incorporate small proportions (less then 10% of oxygenated organic products in premium gasoline without modifying either the specifications of the product or vehicle tuning conditions. Other research is being done on mixtures with a moderate or high methanol content (30, 50 or 90% so as to examine the best possible methods for substituting larger amounts.

LOW PRESSURE CARBURIZING IN A LARGE-CHAMBER DEVICE FOR HIGH-PERFORMANCE AND PRECISION THERMAL TREATMENT OF PARTS OF MECHANICAL GEAR

Directory of Open Access Journals (Sweden)

Emilia Wołowiec-Korecka

2017-03-01

Full Text Available This paper presents the findings of research of a short-pulse low pressure carburizing technology developed for a new large-chamber furnace for high-performance and precision thermal treatment of parts of mechanical gear. Sections of the article discuss the novel constructions of the device in which parts being carburized flow in a stream, as well as the low-pressure carburizing experiment. The method has been found to yield uniform, even and repeatable carburized layers on typical gear used in automotive industry.

The effect of chromium diffusion redistribution on wear resistance of carburized 3Kh13 steel

International Nuclear Information System (INIS)

Shcherbedinskij, G.V.; Shumakov, A.I.; Zemskij, S.V.; Pereverzev, V.M.

1977-01-01

The redistribution of chromium in steel 3Kh13 on carburization in a high-activity carburizer and the wear-resistance of the steel have been investigated. Surface layers with an increased chromium concentration show the highest wear-resistance. The chromium content in the surface layer increases due to its diffusion from the interior. The distribution of carbon and chromium in the carburized layers has been studied with the aid of the radioactive isotope 14 C by the method of layer-by-layer spectral analysis on a vacuum quantometer, layer-by-layer chemical and X-ray structure analysis. The composition of the carbides has been determined by physicochemical analysis. It has been established that the carburized layer can be divided into four zones with respect to its phase composition: first zone - hematite and spinal with 0.5-2.0% C; second zone - solid carbides (Fe,Cr) 7 C 3 ; up to 5% C; third zone - globular carbides in a troostite matrix (Cr,Fe) 7 C 3 and Cr 23 C 6 ; up to 3.5% C; fourth, transitional, zone - troostite carbide mixture Cr 23 C 6 ; up to 1% C. The chromium diffusion in the carburized layer is faster than in the initial austenite. The chromium counterdiffusion is due to the development of a zone of solid carbides M 7 C 3

Pyrolysis of propane under vacuum carburizing conditions. An experimental and modeling study

Energy Technology Data Exchange (ETDEWEB)

Khan, R.U.; Bajohr, S.; Buchholz, D.; Reimert, R. [Engler-Bunte-Institut, Bereich Gas, Erdoel und Kohle, Engler Bunte Ring 1, Universitaet Karlsruhe, 76131 Karlsruhe (Germany); Minh, H.D.; Norinaga, K.; Janardhanan, V.M.; Tischer, S.; Deutschmann, O. [Institute of Chemical Technology, University of Karlsruhe, 76128 Karlsruhe (Germany)

2008-03-15

Propane has been pyrolyzed in a flow reactor system at different temperatures ranging from 640 C to 1010 C and at 8 mbar of partial pressure which are typical vacuum carburizing conditions for steel. Nitrogen was used as a carrier gas. The products of pyrolysis were collected and analyzed by gas chromatography. The reactor was numerically simulated by 1D and 2D flow models coupled to a detailed gas phase reaction mechanism. The gas atmosphere composition has been predicted under the conditions of vacuum carburizing of steel. (author)

Electron bombardment fusion and continuous casting of uranium carbide. Fundamental study of the metallurgical and thermal processes; Fusion sous bombardement d'electrons et coulee continue de carbure d'uranium. Etude fondamentale des processus metallurgiques et thermiques

Energy Technology Data Exchange (ETDEWEB)

Trouve, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-02-01

During a pilot production run, about 1.200 kg of uranium carbide cylindrical rods were prepared by electron bombardment fusion and continuous casting in an apparatus making it possible to operate in a constant vacuum automatically. In order to make the most of the fusion technique used, it was necessary to resolve a certain number of problems involved in this production. It was found that the energy yield for the electron bombardment heating using accelerating voltages of about 10 kV was 100 per cent; about 40 per cent of the electrons are re-emitted by back-scattering. These electrons leave the surface with practically zero energy. The fusion technique leads to the elimination of the majority of the metallic impurities. In order to explain the variations in the non-metallic impurity contents the different reactions occurring in the molten uranium monocarbide have been determined. A micrographic study of the rods obtained has shown various types of crystallization depending on the rate of casting and, despite the uniaxial symmetry of the cooling, no texture has been observed, whatever the rate of fusion employed. The aspects of the fracture surfaces observed on certain rods can be explained by theory in the domain where the material is elastic. Furthermore it has been shown that a decrease in the brittleness occurs as a result of the formation of fine precipitates of the Wiedmanstatten structure type. (authors) [French] Au cours d'une fabrication pilote, environ 1 200 kg de barreaux cylindriques de carbure d'uranium ont ete prepares par fusion sous bombardement d'electrons et coulee continue dans un appareillage permettant d'operer d'une maniere automatique sous vide constant. Afin de tirer le meilleur parti possible de la technique de fusion utilisee, il importait de repondre a un certain nombre de questions soulevees par cette fabrication. Le rendement energetique du chauffage par bombardement d'electrons pour des tensions acceleratrices de l'ordre de 10 kV a ete

Carburizing treatment of low alloy steels: Effect of technological parameters

Science.gov (United States)

Benarioua, Younes

2018-05-01

The surface areas of the parts subjected to mechanical loads influence to a great extent the resistance to wear and fatigue. In majority of cases, producing of a hard superficial layer on a tough substrate is conducive to an increased resistance to mechanical wear and fatigue. Cementation treatment of low alloy steels which bonds superficial martensitic layer of high hardness and lateral compressive to a core of lower hardness and greater toughness is an example of a good solution of the problem. The high hardness of the martensitic layer is due to an increased concentration of interstitial carbon atoms in the austenite before quenching. The lower hardness of the core after quenching is due to the presence of ferrite and pearlite components which appear if the cooling rate after austenitization becomes lower than the critical on. The objective of the present study was to obtain a cemented surface layer on low alloy steel by means of pack carburizing treatment. Different steel grades, austenitization temperatures as well as different soaking times were used as parameters of the pack carburizing treatment. During this treatment, carbon atoms from the pack powder diffuse toward the steels surface and form compounds of iron carbides. The effect of carburizing parameters on the transformation rate of low carbon surface layer of the low alloy steel to the cemented one was investigated by several analytical techniques.

Anti-carburizing Coating for Resin Sand Casting of Low Carbon Steel Based on Composite Silicate Powder Containing Zirconium

Directory of Open Access Journals (Sweden)

Zhan Chunyi

2018-01-01

Full Text Available This paper studied the structure and properties of anticarburizing coating based on composite silicate powder containing zirconium by X-ray diffraction analyzer, thermal expansion tester, digital microscope and other equipment. It is introduced that the application example of the coating in the resin-sand casting of ZG1Cr18Ni9Ti stainless steel impeller. The anti-carburizing effect of the coating on the surface layer of the cast is studied by using direct reading spectrometer and spectrum analyzer. The change of the micro-structure of the coating after casting and cooling is observed by scanning electron microscope. The analysis of anti-carburizing mechanism of the coating is presented. The results indicate that the coating possesses excellent suspension property, brush ability, permeability, levelling property and crackresistance. The coating exhibits high strength and low gas evolution. Most of the coating could be automatically stripped off flakily when the casting was shaken out. The casting possesses excellent surface finish and antimetal penetration effect. The carburizing layer thickness of the stainless steel impeller casting with respect to allowable upper limit of carbon content is about 1mm and maximum carburizing rate is 23.6%. The anticarburizing effect of casting surface is greatly improved than that of zircon powder coating whose maximum carburizing rate is 67.9% and the carburizing layer thickness with respect to allowable upper limit of carbon content is greater than 2mm. The composite silicate powder containing zirconium coating substantially reduces the zircon powder which is expensive and radioactive and mainly dependent on imports. The coating can be used instead of pure zircon powder coating to effectively prevent metal-penetration and carburizing of resin-sand-casting surface of low carbon steel, significantly improve the foundry production environment and reduce the production costs.

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo,Carlos Eduardo; Tschiptschin,André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% c...

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo, Carlos Eduardo; Tschiptschin, André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% carbon super...

Use of Ethanol/Diesel Blend and Advanced Calibration Methods to Satisfy Euro 5 Emission Standards without DPF Utilisation d’un carburant Diesel éthanolé à l’aide de méthodes de calibration avancées afin de satisfaire les normes Euro 5 sans filtre à particules

Directory of Open Access Journals (Sweden)

Magand S.

2011-11-01

innovative calibration methods, based on the simultaneous optimisation of engine basic settings and cold correction maps, are introduced in order to better suit to the new formulation impact on combustion and catalyst light-off and to drop off engine-out unburned hydrocarbons and carbon monoxide emissions. This stage allows pushing forward the work on test bed facilities in order to reduce the amount of vehicle tests. Tests on a chassis dynamometer are only used to validate the engine test bed results and to perform final tuning of cold correction maps. This alternative blend shows potential to achieve Euro 5 standard with Euro 4 Diesel vehicle configuration, without any hardware modification and without a Diesel particulate filter in the exhaust line. Such an innovative fuel formulation seems to be an interesting answer to the trade-off in the forthcoming years between cost and emissions reduction to achieve sustainable mobility. The presented calibration methods and tools allow to fully take advantage of this alternative fuel in a reduced time scale. L’utilisation des biocarburants s’est développée durant ces dernières années de façon importante afin de diversifier les sources d’énergies et de limiter la hausse des émissions de gaz à effet de serre du secteur des transports. L’un des carburants renouvelables les plus adaptés à une production de masse est l’éthanol. Celui-ci est aujourd’hui principalement utilisé dans les moteurs à allumage commandé, alors que la part des véhicules Diesel sur le marché européen est de l’ordre de 60 %. Ce constat nous a incité à proposer une formulation innovante utilisant de l’éthanol pour les applications Diesel. Les principaux verrous technologiques pour cette utilisation sont la miscibilité, la température d’éclair, la lubrification ou encore l’indice de cétane. Des travaux ont été réalisés pour optimiser la formulation contenant de l’éthanol, des biodiesels de première et seconde g

Estimation of fatigue strength enhancement for carburized and shot-peened gears

Science.gov (United States)

Inoue, Katsumi; Kato, Masana

1994-05-01

An experimental formula has been proposed to estimate the bending fatigue strength of carburized gears from the hardness and the residual stress. The derivation of the formula is briefly reviewed, and the effectiveness of the formula is demonstrated in this article. The comparison with many test results for carburized and shot-peened gears verifies that the formula is effective for the approximate estimation of the fatigue strength. The formula quantitatively shows a way of enhancing fatigue strength, i.e., the increase of hardness and residual stress at the fillet. The strength is enhanced about 300 MPa by an appropriate shot peening, and it can be improved still more by the surface removal by electropolishing.

Creep behavior of plasma carburized Ti-6Al-4V alloy

International Nuclear Information System (INIS)

Oliveira, Veronica Mara Cortez Alves de; Barboza, Miguel Justino Ribeiro; Silva, Mariane Capellari Leite da; Pinto, Catia Gisele; Suzuki, Paulo Atsushi; Machado, Joao Paulo B.

2010-01-01

This paper aims to evaluate the effect of plasma carburizing on the Ti-6Al-4V alloy submitted to creep tests. The results showed that the alloy Ti-6Al-4V had a hardness of 334 ± 18 HV. After treatment thermochemical by plasma, was observed the formation of a layer of average thickness of 1,5 μm and hardness of 809 ± 79 HV due to the presence of TiC phase identified by X-ray diffraction. The treatment increased the values of average roughness of 1,28 to 2,02 μm. The creep properties of carburized specimens were improved in comparison with those of the uncarburized Ti-6Al-4V alloy. (author)

Effect on stress-strain relations brought by surface carburization of 316 stainless steel

International Nuclear Information System (INIS)

Matsumoto, K.

1977-01-01

The effect of sodium. environment on austenitic stainless steels used as structural materials in Liquid Metal Cooled Fast Breeder Reactors (LMFBRs) has long been the subject of extensive studies in many countries. Recent developments tending toward stricter control of the oxygen content permitted to be present in the circulating sodium have come to allay the apprehensions formerly held on the possibility of general corrosion affecting the mechanical properties of structural materials expected to be used In LMFBR plants. Grain boundary corrosion and depletion of elements from the structure surface also have come to be considered to provide little cause of fear in this regard, though some uncertainty is still left concerning the influence that these phenomena might exert toward the end of plant life. What still remains essentially to be clarified relates to carbon mass transfer. Decarburization and/or carburization are phenomena that cannot be disregarded even in the primary heat transfer system of LMFBRs, on account of the temperature dependence of carbon activity in steels, which could cause the carbon to leak out from structural material into the circulating sodium in the higher temperature zones of a circuit, to deposit itself on the channel walls in the lower temperature parts. Recent reports on loop experiments point toward the possibility of carboneous matter leaching into flowing sodium and into the cover gas to produce significant carburization phenomena. Carburization, in particular, can bring about loss of ductility and deterioration of fatigue properties, and hence serious consideration of this aspect is called for in the design of components incorporating thin stainless steel plates. To represent the stress-strain behavior at 550 deg. C of 316 stainless steel affected by surface carburization, an empirical formula was adopted. It was proposed by Voce for relating true stress to true plastic strain: σ = Aexp(C ε p ) + B, where σ is the true stress, and

PENGARUH KOMPOSISI ARANG AKTIF DAN KALSIUM KARBONAT PADA PACK CARBURIZING TERHADAP MICROSTRUCTURE

Directory of Open Access Journals (Sweden)

Hafni, Syafrul Hadi

2016-05-01

Full Text Available Penelitian ini bertujuan untuk mendapatkan metode pengerasan  permukaan pada baja lunak, dengan proses pack carburizing. Baja lunak banyak digunakan sebagai bahan dalam pembuatan suatu produk.  Untuk mendapatkan sifat yang keras pada permukaan dan tetap lunak pada intinya maka  dilakukan proses pengerasan permukaan, sehingga produk tersebut dapat difungsikan sesuai dengan  tujuan desainnya. Proses carburizing ini, diperlukan sebuah tungku pembakar yang dirancang tahan panas serta mudah dioperasikan. aman dengan bahan bakar batu bara . untuk penguji tungku yang telah dirancang dilakukan pengujian pada baja rabon rendah dengan mengunakan media karburisasi 1000 gr arang aktif dengan variasi :  200 gram, 100 grm, 66.7 gram Kalsium  karbonat ( CaCo3 pada temperatur   pemanasan 950 0C dan  waktu tahan 4 jam   Kemudian dilanjukan dengan proses quenching. Dari hasil pengujian menunjukan bahan uji dengan komposisi 1000 gr arang aktif dengan 200 gram calcium carbonat lebih baik penambahan unsur karbon sehingga waktu dilakukan quenching terbentuk struktur mikro martensite Kata kunci : Komposisi Arang aktif dan CaCo3, Temperatur, Waktu tahan The goal of the research to obtain surface hardening method on mild steel, with a pack carburizing process. Mild steel is widely used as an ingredient in the manufacture of a product. To get hard on the nature of the surface and remains soft at the core surface hardening process is carried out, so that the product can be used in accordance with the purpose of design.To do this carburizing process, required a stove burner designed heat resistant and easy to operate. safe with fuel coal. for testers furnace that has been designed to do testing on steel Rabon low by using media carburizing 1000 grams of activated charcoal with variations: 200 grams, 100 grm, 66.7 grams of calcium carbonate (CaCO3 at the heating temperature of 950 0C and holding time 4 hours Then dilanjukan with process quenching. Test results

Work function of carburized rhenium

International Nuclear Information System (INIS)

Pallmer, P.G. Jr.; Gordon, R.L.; Dresser, M.J.

1980-01-01

Variations of the electronic work function of carburized rhenium foils containing approximately 5 at.% carbon have been observed using the contact potential difference technique. Surface work function was observed to vary between 5.25 and 4.1 eV, with the work function of pure rhenium taken as 5.0 eV. Decrease in work function has been ascribed to the formation of graphitic layers on the surface at temperatures below the temperature of saturated solubility. The high work function surface was observed with all carbon in solution and has been ascribed to the presence of amorphous carbon near the surface

A model for fracture toughness evaluation of the carburized layer for SAE 5115 steel

OpenAIRE

Sandor, Leonardo Taborda; Ferreira, Itamar

2006-01-01

The purpose of this work is to propose a model for evaluating the fracture toughness along the SAE 5115 steel carburized layer. Due to the small thickness of those layers, it is impossible to machine specimens from those layer in accordance with standards. For simulating the microstructures of the carburized layer in order to get samples for tensile and the fracture toughness testing, specimens of SAE 5115, 5140, 5160, and 52100 steels have been machined, assuming the local influence just the...

EFFECTS OF CARBURIZING AND NITRIDING PROCESSES ON THE COST AND QUALITY OF GEARS PRODUCED WITH AISI 4140 AND 8620 STEELS

Directory of Open Access Journals (Sweden)

Claudio José Leitão

2012-09-01

Full Text Available This study compares the effects of nitriding and carburizing processes applied to gears subjected to contact stresses below 1300 MPa. The manufacturing cost, as well the depth of hardened layer and the distortion produced by two processes are analyzed. AISI 4140 gears quenched, tempered, liquid and gas nitriding and AISI 8620 gears after liquid carburizing, quenching and tempering are analyzed. The dimensional control of the gears was carried out before and after heat and thermochemical treatments. It is concluded that liquid or gas nitriding processes are about 30% more economical than liquid carburizing an also they reduce the dimensional changes. By the other hand liquid carburizing achieves greater case depth. Liquid nitriding process presents the lowest cost, dimensional changes and case depth.

A study of internal oxidation in carburized steels by glow discharge optical emission spectroscopy and scanning electron microscopy

CERN Document Server

An, X; Rainforth, W M; Chen, L

2003-01-01

The internal oxidation of Cr-Mn carburizing steel was studied. Internal oxidation was induced using a commercial carburizing process. Sputter erosion coupled with glow discharge optical emission spectroscopy (GDOES) was used to determine the depth profile elemental distribution within the internal oxidation layer (<10 mu m). In addition, scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) studies were carried out on selected sputter eroded surfaces. Oxide type was identified primarily by transmission electron microscopy (TEM). The carburized surface was found to consist of a continuous oxide layer, followed by a complex internal oxidation layer, where Cr and Mn oxides were found to populate grain boundaries in a globular form in the near surface region. At greater depths (5-10 mu m), Si oxides formed as a grain boundary network. The internal oxides (mainly complex oxides) grew quickly during the initial stages of the carburizing process (2 h, 800 deg. C+3 h, 930 deg. C). G...

The efficiency of different types of wood charcoal on increasing carbon content on surfaces of low carbon steel in the pack carburizing process

Directory of Open Access Journals (Sweden)

Narongsak Thammachot

2014-09-01

Full Text Available The purpose of this research is to compare the efficiency of five types of wood charcoal, eucalyptus, coconut shell, tamarind, bamboo and cassava root in increasing carbon content on surfaces of low carbon steel by the pack carburizing process. The experiment for pack carburized low carbon steel (grade AISI 1020 was conducted by using the different wood charcoals as carburizers, mixed with 10% limestone (by weight as the energizer. The carburizing temperature of 950°C, and carburizing times of 2, 4 and 6 hours were used in the experiment. After grinding, the specimens in each case were checked for carbon content by optical emission spectroscopy. Micro-Vickers hardness testing and microstructure inspections were carried out. The results of the experiment showed that the efficiency of eucalyptus charcoal as the carburizer (for increasing carbon content on surfaces of low carbon steel was higher than that of tamarind, cassava root, coconut shell and bamboo charcoals. The averages for carbon content were: 1.16, 1.06, 0.97, 0.83 and 0.77% respectively.

Effect on stress-strain relations brought by surface carburization of 316 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, K [Ishikawajima-Harima Heavy Industries, Tokyo (Japan)

1977-07-01

The effect of sodium. environment on austenitic stainless steels used as structural materials in Liquid Metal Cooled Fast Breeder Reactors (LMFBRs) has long been the subject of extensive studies in many countries. Recent developments tending toward stricter control of the oxygen content permitted to be present in the circulating sodium have come to allay the apprehensions formerly held on the possibility of general corrosion affecting the mechanical properties of structural materials expected to be used In LMFBR plants. Grain boundary corrosion and depletion of elements from the structure surface also have come to be considered to provide little cause of fear in this regard, though some uncertainty is still left concerning the influence that these phenomena might exert toward the end of plant life. What still remains essentially to be clarified relates to carbon mass transfer. Decarburization and/or carburization are phenomena that cannot be disregarded even in the primary heat transfer system of LMFBRs, on account of the temperature dependence of carbon activity in steels, which could cause the carbon to leak out from structural material into the circulating sodium in the higher temperature zones of a circuit, to deposit itself on the channel walls in the lower temperature parts. Recent reports on loop experiments point toward the possibility of carboneous matter leaching into flowing sodium and into the cover gas to produce significant carburization phenomena. Carburization, in particular, can bring about loss of ductility and deterioration of fatigue properties, and hence serious consideration of this aspect is called for in the design of components incorporating thin stainless steel plates. To represent the stress-strain behavior at 550 deg. C of 316 stainless steel affected by surface carburization, an empirical formula was adopted. It was proposed by Voce for relating true stress to true plastic strain: {sigma} = Aexp(C {epsilon}{sub p} ) + B, where {sigma

Evaluation of Bending Strength of Carburized Gears Based on Inferential Identification of Principal Surface Layer Defects

Science.gov (United States)

Masuyama, Tomoya; Inoue, Katsumi; Yamanaka, Masashi; Kitamura, Kenichi; Saito, Tomoyuki

High load capacity of carburized gears originates mainly from the hardened layer and induced residual stress. On the other hand, surface decarburization, which causes a nonmartensitic layer, and inclusions such as oxides and segregation act as latent defects which considerably reduce fatigue strength. In this connection, the authors have proposed a formula of strength evaluation by separately quantifying defect influence. However, the principal defect which limits strength of gears with several different defects remains unclarified. This study presents a method of inferential identification of principal defects based on test results of carburized gears made of SCM420 clean steel, gears with both an artificial notch and nonmartensitic layer at the tooth fillet, and so forth. It clarifies practical uses of presented methods, and strength of carburized gears can be evaluated by focusing on principal defect size.

Study of the potential use of carburized niobium in plutonium processing

International Nuclear Information System (INIS)

Johnson, M.J.

1998-01-01

Carburized refractory metals, especially tantalum, have been shown to possess properties useful for application as hardware in the plutonium-processing environment. These applications are driven in part by a desire to minimize the production of radioactively contaminated waste. The current use of ceramics as containment materials for Pu processing are not ideal due to the short service life of the hardware, placing an additional burden on the contaminated waste stream. Carburized niobium has been examined for use as an improved hardware material. The Nb-C system is analogous to the previously studied Ta-C system. The low density of niobium relative to tantalum will improve the ergonomics of the glovebox environment. The choice of the Nb-C system will be supported by a thermodynamic and kinetic analysis. Preliminary results of the processing investigation also will be presented

The effects of retained austenite on dry sliding wear behavior of carburized steels

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyung-Jun [Research Inst. of Industrial Science and Technology, Steel Products Dept., Pohang (Korea, Republic of); Kweon, Young-Gak [Research Inst. of Industrial Science and Technology, Steel Products Dept., Pohang (Korea, Republic of)

1996-04-01

Ring-on-square tests on two kinds of low-alloy carburized steel which were AISI 8620 and 4140 were carried out to study the dry sliding wear behavior. The influence of different retained austenite level of 6% to 40% was evaluated while trying to eliminate other factors. Test results show that the effects of grain size and carburized steel species are negligible in dry sliding wear behavior. While the influence of retained austenite is negligible at 20 kg load condition, wear resistance is decreased at 40 kg load condition as the retained austenite level is increased from 6% to 30%. However, wear resistance is again increased above about 30% of retained austenite level at 40 kg load condition. (orig.)

A study of internal oxidation in carburized steels by glow discharge optical emission spectroscopy and scanning electron microscopy

International Nuclear Information System (INIS)

An, X; Cawley, J.; Rainforth, W.M.; Chen, L.

2003-01-01

The internal oxidation of Cr-Mn carburizing steel was studied. Internal oxidation was induced using a commercial carburizing process. Sputter erosion coupled with glow discharge optical emission spectroscopy (GDOES) was used to determine the depth profile elemental distribution within the internal oxidation layer (<10 μm). In addition, scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) studies were carried out on selected sputter eroded surfaces. Oxide type was identified primarily by transmission electron microscopy (TEM). The carburized surface was found to consist of a continuous oxide layer, followed by a complex internal oxidation layer, where Cr and Mn oxides were found to populate grain boundaries in a globular form in the near surface region. At greater depths (5-10 μm), Si oxides formed as a grain boundary network. The internal oxides (mainly complex oxides) grew quickly during the initial stages of the carburizing process (2 h, 800 deg. C+3 h, 930 deg. C). GDOES proved to be an excellent tool for the quantification of oxidation and element distribution as a function of depth, particularly when combined with SEM and TEM to identify oxide type and morphology

Contribution to the study of gaseous Carburization of Uranium

International Nuclear Information System (INIS)

Esteban Hernandez, J. A.; Jimenez Moreno, J. M.; Villota Ruiz, P. de

1966-01-01

Thermal decomposition of uranium hydride powder obtained by hydrogenation of uranium turnings is studied on the first part of this paper. Carburization of the uranium hydride or metallic uranium powder with methane is studied in the second part. A method of uranium monocarbide fabrication under static atmosphere is described. On this method hydrogen is removed by means of an uranium getter. (Author) 6 refs

Isotope ratio measurements of pg-size plutonium samples using TIMS in combination with the 'Multiple Ion Counting' and filament carburization

Energy Technology Data Exchange (ETDEWEB)

Jakopic, Rozle; Richter, Stephan; Kuehn, Heinz; Aregbe, Yetunde [European Commission, Directorate General Joint Research Centre Institute for Reference Materials and Measurements, IRMM Retieseweg 111, B-2440 Geel (Belgium)

2008-07-01

A new sample preparation procedure for isotopic measurements using the Triton TIMS (Thermal Ionization Mass Spectrometer) was developed which employed the technique of carburization of rhenium filaments. Carburized filaments were prepared in a special vacuum chamber in which the filaments were heated and exposed to benzene vapor. Ionization efficiency was improved by an order of magnitude. Additionally, a new 'multi-dynamic' measurement technique was developed for Pu isotope ratio measurements using the 'multiple ion counting' (MIC) system. This technique was further combined with the filament carburization technique and applied to the NBL-137 isotopic standard and samples of the NUSIMEP 5 inter-laboratory comparison campaign. The results clearly show an improved precision and accuracy for the 'multi-dynamic' measurement procedure, compared to measurements carried out either in peak-jumping or in static mode using the MIC system with non-carburized filaments. (authors)

Corrosion and carburization behavior of Al-rich surface layer on Ni-base alloy in supercritical-carbon dioxide environment

Energy Technology Data Exchange (ETDEWEB)

Lee, Ho Jung, E-mail: leehojung@kaist.ac.kr; Kim, Sung Hwan, E-mail: sciencetom@kaist.ac.kr; Kim, Hyunmyung, E-mail: h46kim@kaist.ac.kr; Jang, Changheui, E-mail: chjang@kaist.ac.kr

2016-12-01

Highlights: • Al-rich layer was developed on Alloy 600 by Al deposition and EB remelting. • When exposed to S-CO{sub 2} at 600 °C, mostly Cr{sub 2}O{sub 3} with transition Al{sub 2}O{sub 3} was formed. • Carburized region of amorphous C layer was observed at the oxide/matrix interface. • α-Al{sub 2}O{sub 3} was formed after pre-oxidation which resulted in superior resistance. - Abstract: In order to improve the corrosion and carburization resistance in a high-temperature supercritical-carbon dioxide (S-CO{sub 2}) environment, an Al-rich surface layer was developed on Alloy 600 by Al deposition and a subsequent high energy electron beam (EB) remelting. As a result of the EB surface treatment, an Al enriched (5–7 wt.%) micro-alloying zone (40 μm) was produced. When the EB surface-treated Alloy 600 was corroded in S-CO{sub 2} at 600 °C (20 MPa) for 500 h, the surface oxide layer mostly consisted of chromia (Cr{sub 2}O{sub 3}) with small amount of transition alumina (Al{sub 2}O{sub 3}). In addition, a carburized region of an amorphous C layer inter-mixed with the alumina was observed at the oxide/matrix interface. Meanwhile, when the EB surface-treated specimen was pre-oxidized in helium at 900 °C, α-alumina layer was formed on the surface, which showed superior corrosion and carburization resistance in S-CO{sub 2} environment. Therefore, it could be said that the presence of Al-rich surface layer alone is not enough to provide sufficient corrosion and carburization resistance in S-CO{sub 2} environment at 600 °C, unless pre-oxidation at higher temperature is applied to form a more protective α-alumina on the surface.

Etude numérique et expérimentale de l'evaporation d'une ou plusieurs gouttes de mélange de carburants dans un écoulement chauffé

Science.gov (United States)

Daïf, A.; Ali Chérif, A.; Bresson, J.; Sarh, B.

1995-10-01

The vaporization of one or two multi-component fuel droplets in hot air-stream is presented. A thermal wind tunnel with experimental channel has been designed to develop an experimental process. Firstly, the comparison between experimental results and numerical data is presented for the case of an isolated multi-component droplet. The numerical method is based on the resolution of heat and mass transfer equations between the droplet and the gas stream. This model includes the effect of Stephan flow, the effect of variable thermophysical properties of the components, and the non-unitary Lewis number in the gas film. The experimental results show the micro-explosion phenomenon observed in the liquid phase of multi-component droplet at low temperature. The experimental case of two pure or multi-component droplets in interaction is also presented. On présente un article de synthèse sur l'évaporation d'une ou deux gouttes de carburants à plusieurs composants dans un écoulement d'air chaud. Un dispositif expérimental constitué d'une soufflerie thermique, avec veine d'expérimentation, est réalisé pour permettre cette étude. Pour le cas d'une goutte isolée, une comparaison expérience-calcul est entreprise. Le principe de la méthode numerique consiste en la résolution des équations de transfert de masse et de chaleur entre la goutte et l'écoulement. Ce modèle prend en compte les effets de l'écoulement de Stephan, les variations des propriétés thermophysiques des composants dans les deux phases et la valeur du nombre de Lewis différente de l'unité dans le film de vapeur. Outre l'analyse plus approfondie qu'apporte la confrontation entre le calcul et l'expérience, les résultats expérimentaux montrent le phénomène de micro-explosion observé à l'intérieur de la goutte liquide. Le cas expérimental de deux gouttes en interaction est abordé qu'il s'agisse de gouttes de carburant pur ou de mélange.

The carbide M7C3 in low-temperature-carburized austenitic stainless steel

International Nuclear Information System (INIS)

Ernst, Frank; Li, Dingqiang; Kahn, Harold; Michal, Gary M.; Heuer, Arthur H.

2011-01-01

Prolonged low-temperature gas-phase carburization of AISI 316L-type austenitic stainless steel can cause intragranular precipitation of the carbide M 7 C 3 (M: randomly dispersed Fe, Cr, Ni). Transmission electron microscopy revealed that the carbide particles have the shape of needles. They grow by a ledge-migration mechanism and in a crystallographic orientation relationship to the austenite matrix that enables highly coherent interphase interfaces. A small solubility limit of Ni in the carbide and restricted Ni diffusivity at the processing temperature leads to Ni pileup around the particles and may explain the extreme aspect ratio of the particle shape. These characteristics closely resemble what has been observed earlier for precipitates of M 5 C 2 under slightly different processing conditions and can be rationalized by considering the particular constraints imposed by carburization at low temperature.

Contribution to the study of thermal diffusivity of solids; Contribution a l'etude de la diffusivite thermique des solides

Energy Technology Data Exchange (ETDEWEB)

Zankel, K [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1967-07-01

Angstroem method has been reviewed for its application to measurements of thermal diffusivity and conductivity on short specimens. An apparatus and a technique have been developed for rapid and precise measurements of a large variety of materials, which might also contain heat sources. This technique allows measurements at both high and low temperatures. Stainless steel, nickel and uranium monocarbide specimens were tested and the results of the thermal diffusivity measurements between 50 deg. C and 700 deg. C are presented. (author) [French] L'application de la methode d'Angstroem pour la mesure de la diffusivite et de la conductivite thermique sur des echantillons courts est examinee. Un appareillage est decrit, qui permet non seulement des mesures sur une grande variete de materiaux, mais qui est aussi concu pour des mesures rapides, precises et ou des sources thermiques peuvent etre introduites au sein de l'echantillon. La methode s'adapte egalement aux mesures a basses et hautes temperatures. Des resultats de mesure sur un echantillon en acier inoxydable, en nickel et en carbure d'uranium pour des temperatures comprises entre 50 et 700 deg. C sont reportes. (auteur)

Etude des mécanismes d'interaction, au cours du procédé d'emboutissage à chaud, entre les surces atmosphériques d'hydrogène et les aciers à haute résistance revêtus d'Al-Si

OpenAIRE

Mandy, Mélodie; Jacques, Pascal; Georges, Cédric; Journée Jeunes Chercheurs 2015 - Commission "Corrosion sous contrainte / Fatigue-Corrosion"

2015-01-01

Dans l’industrie automobile, le défi permanent d’allègement en vue de diminuer la consommation de carburant est profitable tant au niveau économique qu’écologique. Pour permettre cette diminution de masse sans compromettre pour autant la sécurité des passagers, il est donc essentiel de développer des nuances d’aciers toujours plus résistantes. Néanmoins, ces aciers doivent également garder une certaine ductilité nécessaire à leur mise en forme, mais aussi fondamentale pour la sécurité des pas...

Detection and molecular cloning of CYP74Q1 gene: identification of Ranunculus acris leaf divinyl ether synthase.

Science.gov (United States)

Gorina, Svetlana S; Toporkova, Yana Y; Mukhtarova, Lucia S; Chechetkin, Ivan R; Khairutdinov, Bulat I; Gogolev, Yuri V; Grechkin, Alexander N

2014-09-01

Enzymes of the CYP74 family, including the divinyl ether synthase (DES), play important roles in plant cell signalling and defence. The potent DES activities have been detected before in the leaves of the meadow buttercup (Ranunculus acris L.) and few other Ranunculaceae species. The nature of these DESs and their genes remained unrevealed. The PCR with degenerate primers enabled to detect the transcript of unknown P450 gene assigned as CYP74Q1. Besides, two more CYP74Q1 isoforms with minimal sequence variations have been found. The full length recombinant CYP74Q1 protein was expressed in Escherichia coli. The preferred substrates of this enzyme are the 13-hydroperoxides of α-linolenic and linoleic acids, which are converted to the divinyl ether oxylipins (ω5Z)-etherolenic acid, (9Z,11E)-12-[(1'Z,3'Z)-hexadienyloxy]-9,11-dodecadienoic acid, and (ω5Z)-etheroleic acid, (9Z,11E)-12-[(1'Z)-hexenyloxy]-9,11-dodecadienoic acid, respectively, as revealed by the data of mass spectrometry, NMR and UV spectroscopy. Thus, CYP74Q1 protein was identified as the R. acris DES (RaDES), a novel DES type and the opening member of new CYP74Q subfamily. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of carburizing helium environment on creep behavior of Ni-base heat-resistant alloys for high-temperature gas-cooled reactors

International Nuclear Information System (INIS)

Kurata, Yuji; Ogawa, Yutaka; Nakajima, Hajime

1988-01-01

Creep tests were conducted on Ni-base heat-resistant alloys Hastelloy XR and XR-II, i.e. versions of Hastelloy X modified for nuclear applications, at 950degC using four types of helium environment with different impurity compositions, and mainly the effect of carburization was examined. For all the materials tested, the values of creep rupture time obtained under the carburizing conditions were similar to or longer than those in the commonly used, standard test environment (JAERI Type B helium). The difference among the results was interpreted by the counterbalancing effects of the strengthening due to carburization and possible weakening caused under very low oxidizing potential. In the corrosion monitoring specimens pronounced carbon pick-up was observed in the environment with high carbon activity and very low oxidizing potential. Based on the results obtained in the present and the previous works, it is suggested that a moderate control of the impurity chemistry is important rather than simple purification of the coolant in protecting the material from the environment-enhanced degradation. Either condition with high or low extremes in the oxidizing and carburizing potentials may cause enhanced degradation and thus are desirable to be avoided at the elevated temperatures. (author)

Combustion of Solid Propellants (La Combustion des Propergols Solides)

Science.gov (United States)

1991-07-01

the of ether and ethyl alcohol and removing objective of these lectures to give a this solvent. Instead of having a fibrous comprehensive understanding...do cetto esrne do Les propergols composites, A matrice confifrences une description tout A fait A polymarique charg~o pst, un oxydant at un jour des...rusa., De nouveaux souvant suppos6 qua la vitesa des gaz de oxydes de for ultrafirts mont aujourd’hui combustion est n~gligeable at qua d~velopps pour

Wear resistance of AISI 304 stainless steel submitted to low temperature plasma carburizing

Directory of Open Access Journals (Sweden)

Marcos Antônio Barcelos

Full Text Available Abstract Despite the AISI 304 stainless steel has high corrosion/oxidation resistance, its tribological properties are poor, being one of the barriers for use in severe wear applications. Thus, there is a wide field for studying technologies that aim to increase the surface hardness and wear resistance of this material. In this work, hardness and wear resistance for AISI 304 stainless steel submitted to the thermochemical treatment by low temperature plasma carburizing (LTPC in a fixed gas mixture composition of 93% H2 and 7% CH4 are presented. Through the evaluation of the carburizing layers, it was possible to observe a substantial improvement in tribological properties after all temperature and time of treatment. This improvement is directly related to the increase of the process variables; among them temperature has a stronger influence on the wear resistance obtained using LTPC process.

Contribution to the study of thermal diffusivity of solids; Contribution a l'etude de la diffusivite thermique des solides

Energy Technology Data Exchange (ETDEWEB)

Zankel, K. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1967-07-01

Angstroem method has been reviewed for its application to measurements of thermal diffusivity and conductivity on short specimens. An apparatus and a technique have been developed for rapid and precise measurements of a large variety of materials, which might also contain heat sources. This technique allows measurements at both high and low temperatures. Stainless steel, nickel and uranium monocarbide specimens were tested and the results of the thermal diffusivity measurements between 50 deg. C and 700 deg. C are presented. (author) [French] L'application de la methode d'Angstroem pour la mesure de la diffusivite et de la conductivite thermique sur des echantillons courts est examinee. Un appareillage est decrit, qui permet non seulement des mesures sur une grande variete de materiaux, mais qui est aussi concu pour des mesures rapides, precises et ou des sources thermiques peuvent etre introduites au sein de l'echantillon. La methode s'adapte egalement aux mesures a basses et hautes temperatures. Des resultats de mesure sur un echantillon en acier inoxydable, en nickel et en carbure d'uranium pour des temperatures comprises entre 50 et 700 deg. C sont reportes. (auteur)

Evaluation of carburization depth in service exposed ferritic steel using magnetic Barkhausen noise analysis

International Nuclear Information System (INIS)

Vaidyanathan, S.; Moorthy, V.; Jayakumar, T.; Baldev Raj

1996-01-01

The feasibility of using magnetic Barkhausen (MBN) measurement for the evaluation of carburization depth in ferritic steels has been reported in this paper. MBN measurements were carried out on samples from service exposed 0.5Cr-0.5Mo ferritic steel tube at different depths (cross section) from carburised ID surface to simulate the variation in carbon concentration gradient within the skin depth of MBN with increasing time of exposure to carburization. It has been observed that the MBN level increases with increasing depth of measurement. An inverse relation between MBN level and carbon content/hardness value has been observed. This study suggests that, the MBN measurements on the carburised surface can be correlated with the concentration gradient within the skin depth of the MBN which would help in predicting the approximate depth of the carburised layer with proper prior calibration. (author)

Zircon Carburation Studies as Intermediate Stage in the Zirconium Fabrication

International Nuclear Information System (INIS)

Almagro Huertas, V.; Saenz de Tejada Gonzalez, L.; Lopez Rodriguez, M.

1963-01-01

Zirconium carbide and carbonitride mixtures were obtained by Kroll's method.Reaction products have been identified by micrography and X-ray diffraction analysis. The optimum graphite content in the initial charge for the carburation reaction has been studied. zirconium, silicon and carbon content in the final product has been controlled as a function of current in the furnace and reaction time.Further chlorination of the final product was performed successfully. (Author) 16 refs

Boronization and Carburization of Superplastic Stainless Steel and Titanium-Based Alloys

Directory of Open Access Journals (Sweden)

Masafumi Matsushita

2011-07-01

Full Text Available Bronization and carburization of fine-grain superplastic stainless steel is reviewed, and new experimental results for fine grain Ti88.5Al4.5V3Fe2Mo2 are reported. In superplastic duplex stainless steel, the diffusion of carbon and boron is faster than in non-superplastic duplex stainless steel. Further, diffusion is activated by uniaxial compressive stress. Moreover, non-superplastic duplex stainless steel shows typical grain boundary diffusion; however, inner grain diffusion is confirmed in superplastic stainless steel. The presence of Fe and Cr carbides or borides is confirmed by X-ray diffraction, which indicates that the diffused carbon and boron react with the Fe and Cr in superplastic stainless steel. The Vickers hardness of the carburized and boronized layers is similar to that achieved with other surface treatments such as electro-deposition. Diffusion of boron into the superplastic Ti88.5Al4.5V3Fe2Mo2 alloy was investigated. The hardness of the surface exposed to boron powder can be increased by annealing above the superplastic temperature. However, the Vickers hardness is lower than that of Ti boride.

L'hydrodésazotation des distillats issus de la conversion des hydrocarbures lourds Hydrodenitrogenation of Distillates Issuing from the Conversion of Heavy Hydrocarbons

Directory of Open Access Journals (Sweden)

Toulhoat H.

2006-11-01

Full Text Available L'hydrodésazotation catalytique (HDN est un des points clés de la valorisation des hydrocarbures lourds par leur conversion en carburants. Les coupes lourdes sont riches en azote, et leur conversion produit des distillats eux-mêmes très riches en azote, qui ne pourront être absorbés par une raffinerie classique sans un sévère prétraitement désazotant. Ce problème se pose quel que soit le procédé de conversion mis en oeuvre. On propose donc une analyse de l'HDN comprenant la description des structures azotées rencontrées dans les coupes à traiter, la mise en évidence des réactions à promouvoir, et les règles de choix de catalyseurs et de conditions opératoires en découlant compte tenu des principales déterminantes thermodynamiques et cinétiques. Cette analyse s'appuie sur des résultats de recherche très récents. Elle conduit à la mise en évidence de solutions actuelles au problème posé, et ouvre des perspectives pour des améliorations futures. Catalytic hydrodenitrogenation (HDN is one of the key steps in the upgrading of heavy hydrocarbons by converting them into fuels. Heavy cuts are rich in nitrogen, and their conversion produces distillates that are also very rich in nitrogen, making them unable to be absorbed by a conventional refinery without a severe denitrogenation pretreatment. This problem occurs no matter what conversion process is implemented. Therefore, an analysis of HDN is proposed, including the description of the nitrogen structures encountered in the cuts to be treated, the description of the reactions to be promoted, and the resulting rules for choosing catalysts and operating conditions, in the light of the principal thermodynamic and kinetic constraints. This analysis is based on very recent research results. It leads to the recommending of solutions to the problem at hand and opens up prospects for future improvements.

Unique low-molecular-weight lignin with high purity extracted from wood by deep eutectic solvents (DES): a source of lignin for valorization

Energy Technology Data Exchange (ETDEWEB)

Alvarez-Vasco, Carlos; Ma, Ruoshui; Quintero, Melissa; Guo, Mond; Geleynse, Scott; Ramasamy, Karthikeyan K.; Wolcott, Michael; Zhang, Xiao

2016-01-01

This paper reports a new method of applying Deep Eutectic Solvents (DES) for extracting lignin from woody biomass with high yield and high purity. DES mixtures prepared from Choline Chloride (ChCl) and four hydrogen-bond donors–acetic acid, lactic acid, levulinic acid and glycerol–were evaluated for treatment of hardwood (poplar) and softwood (D. fir). It was found that these DES treatments can selectively extract a significant amount of lignin from wood with high yields: 78% from poplar and 58% from D. fir. The extracted lignin has high purity (95%) with unique structural properties. We discover that DES can selectively cleave ether linkages in wood lignin and facilitate lignin removal from wood. The mechanism of DES cleavage of ether bonds between phenylpropane units was investigated. The results from this study demonstrate that DES is a promising solvent for wood delignification and the production of a new source of lignin with promising potential applications.

Etude d'un procédé d'hydroliquéfaction du charbon pour la production simultanée de gaz et de carburant . . . . . Studies of a Coal Hydrogenation Process to Produce CO-Currently Gas and Gasoline

Directory of Open Access Journals (Sweden)

Franckowiak S.

2006-11-01

Full Text Available Un des principaux moyens de réintroduire le charbon dans le marché énergétique français est de le transformer en produits utiles comme le gaz de réseau ou les carburants. Les procédés d'oxyvapogazéification permettent d'obtenir un gaz de synthèse qui peut être ensuite converti en gaz riche ou en produits liquides. L'hydrogénation en phase liquide (ou hydroliquéfaction se présente pour le long terme comme une seconde voie qui offre des avantages spécifiques - taux de conversion du charbon et rendement élevés, - production directe de gaz de substitution (GNS et de carburant, - possibilité d'utilisation d'hydrogène provenant de l'électricité nucléaire. Un programme d'étude a été lancé avec la participation du Gaz de France (GDF, du Centre d'études et de recherches des Charbonnages de France (Cerchar, de l'institut Français du Pétrole (lFP et du Centre National de la Recherche Scientifique (CNRS dans le cadre du Groupe d'Étude de la Conversion du Charbon par Hydrogénation (GECH. Un banc d'essai d'hydroliquéfaction situé au Cerchar, d'un débit de 10 kg/h de mélange charbon-solvant, permet d'obtenir des hydrogénats dans des conditions variées et en présence de divers catalyseurs. L'étude de la valorisation de ces hydrogénats est effectuée dans les laboratoires de l'lFP. Les essais et les études effectués permettent d'envisager la production à volonté du GNS, de carburants ou des deux ensemble. Un modèle d'optimisation a été réalisé au GDF pour étudier et comparer les différentes filières en prenant en compte l'utilisation d'hydrogène d'électrolyse ou d'hydrogène produit sur place à partir du résidu de liquéfaction. One of the main ways to bring coal in the future french energy market is to transform it into valuable products. The oxygen steam gasification processes give a synthesis gas which can be converted into SNG or gasoline in a catalytic stage. The liquid phase hydrogenation process is a

Study of the carburization of an austenitic steel through optical and scanning electron microscopy, microhardness and X ray microanalysis of C

International Nuclear Information System (INIS)

Champigny, Michel; Gauvain, Danielle; Meny, Lucienne

1977-01-01

Carburization tests of 316 L stainless steel have been performed in liquid sodium at 550, 600 and 650 0 C; the depth of penetration of carbon is of the order of 300 μm. The structure of the carburized layer has been studied through optical and scanning electron microscopy: the carbides precipitate first within the grain boundaries, making a nearly continuous superficial carbide layer. The Vickers and Knoop (under 50 g load) microhardness measurements determine the depth of carburization with an error of +-50μm. Though the tensile strength does not vary much with the carburization, the striction, and then the deformation capability, is highly decreased. The variation of the concentration in carbon versus distance has been measured by quantitative X ray microanalysis, using diamond as a standard; the best experimental conditions, regarding the overlapping of the Cr 2 Lα and Ni 3 Lα lines with CK line have been chosen, and the minimum contamination during the measurements has been performed. The results have been confirmed by the analysis of carbon in Fe Ni standards containing less than 1 w/o carbon. The results are discussed with the published data. This work shows that: the increase of microhardness is not related in a simple way with the carbon content of the stainless steel; the carbon concentration can be measured quickly with an error of +-5% when 0,2 [fr

Fonctionnement transitoire et controle de la richesse des moteurs à allumage commandé à injection multipoint Transient Operation and Air-Fuel Ratio Control of Spark-Ignition Port-Injected Engines

Directory of Open Access Journals (Sweden)

Le Moyne L.

2006-12-01

Full Text Available Sur les moteurs à allumage commandé à injection multipoint on observe des désadaptations de richesse lors de fonctionnement transitoire. Ces désadaptations sont dues au dépôt, sous forme de film liquide, du carburant injecté dans le collecteur. Elles peuvent être compensées par une gestion adéquate de la masse injectée. Ainsi, afin d'obtenir la masse de carburant qui maintient la richesse constante, nous avons développé un modèle bidimensionnel des écoulements dans le collecteur au cours du cycle moteur. Ce modèle décrit l'écoulement des gaz frais, des gouttes injectées, des gaz brûlés refoulés vers l'admission et du film sur les parois, sur le principe de la séparation des phases. Nous montrons que le modèle reproduit correctement le signal de richesse et comment il permet de supprimer les désadaptations. La mesure de richesse est faite à l'échappement avec une sonde à oxygène dont nous validons le fonctionnement en transitoire avec une corrélation à la pression maximale du cycle dans le cylindre. Air-fuel ratio excursions are observed on port-injected spark ignition engines during transients. This excursions result from the liquid fuel film deposited on intake port. They can be compensated by controlling the injected fuel mass. In order to have the amount of fuel that keeps air-fuel ratio constant, we have developed a 2D model of flows in the intake port during engine cycle. This separate phases model describes the flow of fresh gases, injected droplets, hot burned gases and film on port walls. We show that the model effectively predicts the equivalence ratio and how it allows to eliminate excursions. Equivalence ratio measures are made with an oxygen sensor which functioning is validated during transients by correlating it to maximal pressure during engine cycle.

The carbide M{sub 7}C{sub 3} in low-temperature-carburized austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Ernst, Frank, E-mail: frank.ernst@cwru.edu [Department of Materials Science and Engineering, Case Western Reserve University, Cleveland, OH 44106-7204 (United States); Li, Dingqiang; Kahn, Harold; Michal, Gary M.; Heuer, Arthur H. [Department of Materials Science and Engineering, Case Western Reserve University, Cleveland, OH 44106-7204 (United States)

2011-04-15

Prolonged low-temperature gas-phase carburization of AISI 316L-type austenitic stainless steel can cause intragranular precipitation of the carbide M{sub 7}C{sub 3} (M: randomly dispersed Fe, Cr, Ni). Transmission electron microscopy revealed that the carbide particles have the shape of needles. They grow by a ledge-migration mechanism and in a crystallographic orientation relationship to the austenite matrix that enables highly coherent interphase interfaces. A small solubility limit of Ni in the carbide and restricted Ni diffusivity at the processing temperature leads to Ni pileup around the particles and may explain the extreme aspect ratio of the particle shape. These characteristics closely resemble what has been observed earlier for precipitates of M{sub 5}C{sub 2} under slightly different processing conditions and can be rationalized by considering the particular constraints imposed by carburization at low temperature.

The Effects of CO{sub 2} Pressure on Corrosion and Carburization Behaviors of Chromia-forming Austenitic Alloys

Energy Technology Data Exchange (ETDEWEB)

Lee, Ho Jung; Kim, Sung Hwan; Jang, Changheui [KAIST, Daejeon (Korea, Republic of)

2015-05-15

By applying S-CO{sub 2} cycle to SFR, the inherent safety could be improved by alleviating the concern of explosive reaction between high temperature steam and liquid sodium as well as increased thermal efficiency at 500-550 .deg. C compared to helium Brayton cycle. Meanwhile, from the material point of view, a compatibility such as corrosion and carburization of candidate materials in S-CO{sub 2} environment should be evaluated to assure the long-term integrity of IHX. It has been previously reported that Ni-base alloys and high-Cr Fe-base austenitic alloys showed a good corrosion resistance by the formation of thin chromia layer while carburization behaviors of those materials were not properly investigated. Corrosion and carburization behaviors of three chromia-forming austenitic alloys (Ni-base alloys and Alloy 800HT) were evaluated in S-CO{sub 2} (200 bar) and CO{sub 2} (1 bar) environment at 550.650 .deg. C for 1000 h. For all test materials, a good corrosion resistance was exhibited by the formation of thin chromia (Cr{sub 2}O{sub 3}) with small amount of minor oxides such as Mn1.5Cr1.5O{sub 4}, Al{sub 2}O{sub 3}, and TiO{sub 2}.

The structure of para-toluidine by X-ray and neutron diffraction; Etude de la structure de la para-toluidine par la diffraction des rayons X et des neutrons

Energy Technology Data Exchange (ETDEWEB)

Bertinotti, A.L. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-12-01

The crystal and molecular structure of para-toluidine has been solved by X-ray and neutron diffraction counter techniques. The molecules are arranged in the form of infinite chains in the crystal, each molecule being linked to two neighbours by hydrogen bonds. The presence of the H bonds makes clear the difference in the melting points between para-toluidine and benzene hydrocarbons of related symmetry and molecular weight. Their direction accounts for the (001) cleavage and the growth anisotropy of crystals from supersaturated vapour phase. A structure-seeking method by computer has been elaborated, using lattice energy calculations applied to molecules treated as rigid bodies and making use of a simplex method for function minimization without calculation of derivatives. The way the available information is handled allows to increase the range of convergence, as shown in the case of para-toluidine. (author) [French] La structure cristalline et moleculaire de la para-toluidine a ete resolue a l'aide de la diffraction des rayons X et des neutrons. L'analyse a revele que la structure presentait un encha ement particulier des molecules, liees entre elles par des ponts hydrogene. La presence des liaisons rend compte de l'elevation du point de fusion de la para-toluidine par rapport a celui des carbures benzeniques de symetrie et de poids moleculaires voisins. La direction des liaisons explique le clivage facile (001) des cristaux obtenus par fusion et l'anisotropie de croissance des cristaux en phase vapeur. Une methode de recherche de structures par ordinateur a ete elaboree, faisant usage du concept d'energie reticulaire applique aux molecules considerees comme rigides et faisant appel a une methode de simplexe pour la minimisation des fonctions sans calcul de derivees. La maniere dont est exploitee l'information disponible permet d'accro re, comme cela est montre dans le cas de la para-toluidine, l'etendue du domaine de

The structure of para-toluidine by X-ray and neutron diffraction; Etude de la structure de la para-toluidine par la diffraction des rayons X et des neutrons

Energy Technology Data Exchange (ETDEWEB)

Bertinotti, A L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-12-01

The crystal and molecular structure of para-toluidine has been solved by X-ray and neutron diffraction counter techniques. The molecules are arranged in the form of infinite chains in the crystal, each molecule being linked to two neighbours by hydrogen bonds. The presence of the H bonds makes clear the difference in the melting points between para-toluidine and benzene hydrocarbons of related symmetry and molecular weight. Their direction accounts for the (001) cleavage and the growth anisotropy of crystals from supersaturated vapour phase. A structure-seeking method by computer has been elaborated, using lattice energy calculations applied to molecules treated as rigid bodies and making use of a simplex method for function minimization without calculation of derivatives. The way the available information is handled allows to increase the range of convergence, as shown in the case of para-toluidine. (author) [French] La structure cristalline et moleculaire de la para-toluidine a ete resolue a l'aide de la diffraction des rayons X et des neutrons. L'analyse a revele que la structure presentait un encha ement particulier des molecules, liees entre elles par des ponts hydrogene. La presence des liaisons rend compte de l'elevation du point de fusion de la para-toluidine par rapport a celui des carbures benzeniques de symetrie et de poids moleculaires voisins. La direction des liaisons explique le clivage facile (001) des cristaux obtenus par fusion et l'anisotropie de croissance des cristaux en phase vapeur. Une methode de recherche de structures par ordinateur a ete elaboree, faisant usage du concept d'energie reticulaire applique aux molecules considerees comme rigides et faisant appel a une methode de simplexe pour la minimisation des fonctions sans calcul de derivees. La maniere dont est exploitee l'information disponible permet d'accro re, comme cela est montre dans le cas de la para-toluidine, l'etendue du domaine de convergence. (auteur)

Carburization of austenitic and ferritic alloys in hydrocarbon environments at high temperature

Directory of Open Access Journals (Sweden)

Serna, A.

2003-12-01

Full Text Available The technical and industrial aspects of high temperature corrosion of materials exposed to a variety of aggressive environments have significant importance. These environments include combustion product gases and hydrocarbon gases with low oxygen potentials and high carbon potentials. In the refinery and petrochemical industries, austenitic and ferritic alloys are usually used for tubes in fired furnaces. The temperature range for exposure of austenitic alloys is 800-1100 °C, and for ferritic alloys 500-700 °C, with carbon activities a_c > 1 in many cases. In both applications, the carburization process involves carbon (coke deposition on the inner diameter, carbon absorption at the metal surface, diffusion of carbon inside the alloy, and precipitation and transformation of carbides to a depth increasing with service. The overall kinetics of the internal carburization are approximately parabolic, controlled by carbon diffusion and carbide precipitation. Ferritic alloys exhibit gross but uniform carburization while non-uniform intragranular and grain-boundary carburization is observed in austenitic alloys.

La corrosión a alta temperatura, tal como la carburación de materiales expuestos a una amplia variedad de ambientes agresivos, tiene especial importancia desde el punto de vista técnico e industrial. Estos ambientes incluyen productos de combustión, gases e hidrocarburos con bajo potencial de oxígeno y alto potencial de carbono. En las industrias de refinación y petroquímica, las aleaciones austeníticas y ferríticas se utilizan en tuberías de hornos. El rango de temperatura de exposición para aleaciones austeníticas está entre 800-1.100°C y para aleaciones ferríticas está entre 500-700°C, con actividades de carbono a_c>1 en algunos casos. En tuberías con ambas aleaciones, el proceso de carburación incluye deposición de carbón (coque en el diámetro interno, absorción de carbono en la superficie

Irradiation behaviour of mixed uranium-plutonium carbides, nitrides and carbonitrides; Comportement a l'irradiation de carbures, nitrures et carbonitrures mixtes d'uranium et de plutonium

Energy Technology Data Exchange (ETDEWEB)

Mikailoff, H; Mustelier, J P; Bloch, J; Leclere, J; Hayet, L [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

In the framework of the research program of fast reactor fuels two irradiation experiments have been carried out on mixed uranium-plutonium carbides, nitrides and carbo-nitrides. In the first experiment carried out with thermal neutrons, the fuel consisted of sintered pellets sheathed in a stainless steel can with a small gap filled with helium. There were three mixed mono-carbide samples and the maximum linear power was 715 W/cm. After a burn-up slightly lower than 20000 MW day/tonne, a swelling of the fuel which had ruptured the cans was observed. In the second experiment carried out in the BR2 reactor with epithermal neutrons, the samples consisted of sintered pellets sodium bonded in a stainless steel tube. There were three samples containing different fuels and the linear power varies between 1130 and 1820 W/cm. Post-irradiation examination after a maximal burn-up of 1550 MW day/tonne showed that the behaviour of the three fuel elements was satisfactory. (authors) [French] Dans le cadre du programme d'etude des conibustiles pour reacteurs rapides, on a realise deux experiences d'irradiation de carbures, nitrures et carbonitrures mixtes d'uranium et de plutonium. Dans la premiere experience, faite en neutrons thermiques, le combustible etait constitue de,pastilles frittees gainees dans un tube d'acier inoxydable avec un faible jeu rempli d'helium. Il y avait trois echantillons de monocarbures mixtes, et la puissance lineaire maximale etait de 715 W/cm. Apres un taux de combustion legerement inferieur a 20 000 MWj/t, on a observe un gonflement des combustible qui a provoque, la rupture des gaines. Pans la seconde experience, realisee dans le reacteur BR2 en neutrons epithermiques, les echantillons etaient constitues de pastilles frittees gainees dans un tube d'acier avec un joint sodium. Il y avait trois echantillons contenant des combustibles differents, et la puissance lineaire variait de 1130 a 1820 W/cm. Les examens apres irradiation a un taux maximal de

A Comparison of Effects of Ambient Pressure on the Atomization Performance of Soybean Oil Methyl Ester and Dimethyl Ether Sprays Comparaison des effets de la pression ambiante sur l’atomisation en “spray” de methylester d’huile de soja et de dimethyléther

Directory of Open Access Journals (Sweden)

Kim H.J.

2010-11-01

Full Text Available The purpose of this study is the experimental investigation of Soybean oil Methyl Ester (SME and DiMethyl Ether (DME spray characteristics injected through the common-rail injection system under various ambient pressures. A high pressure chamber that can be pressurized up to 4 MPa was utilized for a change of ambient pressure. In order to compare the spray development and atomization characteristics, the images of SME and DME were obtained by using a high speed camera with two metal halide lamps under various ambient pressures in the spray chamber. From these spray images, the spray characteristics such as the spray penetration from the nozzle tip, maximum radial distance, and spray diameter were measured and analyzed. In addition, the Sauter Mean Diameter (SMD of two fuels under ambient pressure was analyzed using the droplet measuring system. It was revealed that the axial distance of spray from the nozzle tip of the SME spray is longer than that of DME spray under same injection condition. The axial penetration, maximum radial distance, and spray diameter decreased when the ambient pressure in the chamber increased. As the ambient pressure increased, the SMD decreased and the DME spray showed a superior atomization performance compared to the SME spray. Le but de cette étude est l’investigation expérimentale de l’effet de diverses pressions ambiantes sur les caractéristiques des sprays (issus d’un système "common rail" de methylester d’huile de soja (SME et de dimethyléther (DME. La pression ambiante dépend de la chambre et sa valeur la plus haute peut monter jusqu’à 4 MPa. Pour comparer le développement de spray et la caractéristique d’atomisation, des images de spray de SME et DME à différentes pression ambiantes sont obtenues avec une caméra à haute vitesse à deux lampes de métal halide. Les caractéristiques du spray, comme la pénétration, la distance radiale maximale et le diamètre de spray, sont mesur

Comparison of Properties among Dendritic and Hyperbranched Poly(ether ether ketones and Linear Poly(ether ketones

Directory of Open Access Journals (Sweden)

Atsushi Morikawa

2016-02-01

Full Text Available Poly(ether ether ketone dendrimers and hyperbranched polymers were prepared from 3,5-dimethoxy-4′-(4-fluorobenzoyldiphenyl ether and 3,5-dihydroxy-4′-(4-fluorobenzoyldiphenyl ether through aromatic nucleophilic substitution reactions. 1-(tert-Butyldimethylsiloxy-3,5-bis(4-fluorobenzoylbenzene was polycondensed with bisphenols, followed by cleavage of the protective group to form linear poly(ether ketones having the same hydroxyl groups in the side chains as the chain ends of the dendrimer and hyperbranched polymers. Their properties, such as solubilities, reduced viscosities, and thermal properties, were compared with one another. Similar comparisons were also carried out among the corresponding methoxy group polymers, and the size of the molecules was shown to affect the properties.

Study of the machining of uranium carbide rods obtained by continuous casting under electronic bombardment; Etude de l'usinage de barreaux de carbure d'uranium obtenus par coulee continue sous bombardement electronique

Energy Technology Data Exchange (ETDEWEB)

Rousset, P; Accary, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-07-01

The authors consider the various methods of machining uranium mono-carbide and compare them critically in the case of their application to uranium carbide obtained by fusion under an electronic bombardment and continuous casting. This study leads them to propose two mechanical machining methods: cylindrical rectification and center-less rectification, preceded by a preliminary roughing out of a cylinder, the latter appearing more suitable. A study of the machining yields as a function of the diameter of the rough bars and of the diameter of the finished rods has shown that an optimum value of the rough bar diameter exists for each value of the finished rod diameter. It is found that the yield increases as the diameter itself increases, this yield rising from 45 per cent to around 70 per cent as the diameter of the rough bars increases from 25-26 mm to 37-38 mm. (authors) [French] Les auteurs envisagent les differentes methodes d'usinage du monocarbure d'uranium et se livrent a une etude critique de celles-ci, dans le cas de leur application a l'usinage de barreaux de carbure d'uranium obtenus par fusion sous bombardement electronique et coulee continue. Cette etude les conduit a proposer deux methodes d'usinage mecanique: la rectification cylindrique et la rectification 'centerless', precedee d'un ebauchage par carottage, la seconde paraissant la plus appropriee. L'etude des rendements d'usinage en fonction du diametre des barreaux bruts et du diametre des barreaux finis, a mis en evidence une valeur optimale du diametre des barreaux bruts pour chaque valeur du diametre des barreaux usines. Elle a montre que le rendement croit lorsque le diametre croit lui-meme, ce rendement passant d'environ 45 pour cent a environ 70 pour cent, lorsque le diametre des barreaux bruts passe de 25-26 mm a 37-38 mm.

Numerical analysis of spray characteristics of dimethyl ether and diethyl ether fuel

International Nuclear Information System (INIS)

Mohan, Balaji; Yang, Wenming; Yu, Wenbin; Tay, Kun Lin

2017-01-01

Highlights: • Thermo-physical properties of liquid DME and DEE are reported. • Ether fuels tend to cavitate higher compared to that of diesel fuel. • Spray tip penetration and SMD are found to be lesser for ether fuels. • Ether fuels shows excellent atomization behavior. - Abstract: In this work, the spray characteristics of ether fuels such as dimethyl ether (DME) and diethyl ether (DEE) have been numerically investigated using KIVA-4 CFD code. A new hybrid spray model developed by coupling the standard KHRT model to cavitation sub model was used. The detailed thermo-physical properties of ether fuels have been predicted and validated with experimental results available from literature. The cavitation inception inside the injector nozzle hole has been studied for ether fuels in comparison with diesel fuel. It was found that ether fuels cavitates higher compared to that of conventional diesel fuel because of its low viscosity. The spray tip penetration of diesel fuel was longer than that of ether fuels due to high viscosity and density of diesel fuel. Ether fuels characterized by low Ohnesorge number and high Reynolds number showed better atomization behavior compared to that of the diesel fuel.

Identification of a process window for tailored carburization of sheet metals in hot stamping

Science.gov (United States)

Horn, Alexander; Merklein, Marion

2018-05-01

Due to governmental regulations concerning the reduction of CO2 emissions and increasing safety standards, hot stamping of high strength boron manganese steel sheets has evolved into a state of the art process for manufacturing structural car body parts. The combined forming and in-die quenching process enables the formation of a fully martensitic microstructure. Therefore, press hardened steels offer high strength, but low ductility. In order to further improve passenger safety, a tailored configuration of mechanical properties is desired. Besides state of the art methods, like the application of locally different heat treatment temperatures or varying quenching rates, the adjustment of mechanical properties of sheet metals by a tailored carburization is a novel approach. For the carburization process, the specimens are first coated with graphite and subsequently heat treated. Within this contribution, different coating strategies as well as heat treatment temperatures and dwell times are investigated. For the determination of a process window, mechanical properties such as tensile strength and microhardness will be analyzed and correlated with the resulting microstructure.

Effects of niobium additions on the structure, depth, and austenite grain size of the case of carburized 0.07% C steels

Science.gov (United States)

Islam, M. A.; Bepari, M. M. A.

1996-10-01

Carbon (0.07%) steel samples containing about 0.04% Nb singly and in combination with nitrogen were carburized in a natural Titas gas atmosphere at a temperature of 1223 K (950 °C) and a pressure of about 0.10 MPa for 1/2 to 4 h, followed by slow cooling in the furnace. Their microstructures were studied by optical microscopy. The austenite grain size of the case and the case depths were determined on baseline samples of low-carbon steels and also on niobium and (Nb + N) microalloyed steel samples. It was found that, when compared to the baseline steel, niobium alone or in combination with nitrogen decreased the thickness of cementite network near the surface of the carburized case of the steels. However, niobium in combination with nitrogen was more effective than niobium in reducing the thickness of cementite network. Niobium with or without nitrogen inhibited the formation of Widmanstätten cementite plates at grain boundaries and within the grains near the surface in the hypereutectoid zone of the case. It was also revealed that, when compared to the baseline steel, niobium decreased the case depth of the carburized steels, but that niobium with nitrogen is more effective than niobium alone in reducing the case depth. Niobium as niobium carbide (NbC) and niobium in the presence of nitrogen as niobium carbonitride, [Nb(C,N)] particles refined the austenite grain size of the carburized case, but Nb(C,N) was more effective than NbC in inhibiting austenite grain growth.

Oxidation of iron and steels by carbon dioxide under pressure (1962); Oxydation du fer et des aciers par l'anhydride carbonique sous pression (1962)

Energy Technology Data Exchange (ETDEWEB)

Colombie, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-01

After having developed one of the first thermo-balances to operate under pressure, we have studied the influence of the pressure on the corrosion of iron and steels by carbon dioxide. The corrosion was followed by three different methods simultaneously: by the oxidation kinetics, by micrographs, and by radiocrystallography. We have been able to show that the influence of the pressure is not negligible and we have provided much experimental evidence: oxidation kinetics, micrographic aspects, surface precipitation of carbon, metal carburization, the texture of the magnetite layer. All these phenomena are certainly modified by changes in the carbon dioxide pressure. In order to interpret most of our results we have been led to believe that the phenomenon of corrosion by CO{sub 2} depends on secondary reactions localised at the oxide-gas interface. This would constitute a major difference between the oxidation by CO{sub 2} and that by oxygen. (author) [French] Apres avoir etudie et mis au point une des premieres thermobalances fonctionnant sous pression, nous avons etudie l'influence de la pression sur la corrosion du fer et des aciers par l'anhydride carbonique. Notre etude a ete conduite simultanement sur trois plans differents: etude des cinetiques d'oxydation, etude micrographique et etude radiocristallographique. Nous avons pu montrer que l'influence de la pression n'etait pas negligeable et nous en avons fourni un faisceau de preuves experimentales important: cinetiques d'oxydation, aspect micrographique, precipitation superficielle de carbone, carburation du metal, texture de la couche de magnetite. Tous ces phenomenes sont sans aucun doute modifies par une variation de pression du gaz carbonique. Pour interpreter la plupart de nos resultats, nous avons ete conduits a penser que le phenomene de corrosion par CO{sub 2} etait tributaire de reactions secondaires localisees a l'interface oxyde-gaz. Ce serait la une des differences fondamentales entre l'oxydation par

Biocarburants : la Commission propose d’encourager leur utilisation

Directory of Open Access Journals (Sweden)

Vermeersch Georges

2002-01-01

Full Text Available Depuis longtemps, la Commission, le Parlement et le Conseil encouragent le développement des sources d’énergie renouvelables, et plus particulièrement des biocarburants. Cela s’est traduit, entre autres, par la publication en novembre 2000 d’un livre vert intitulé « Vers une stratégie européenne de sécurité d’approvisionnement énergétique », qui fixe comme objectif, d’ici 2020, le remplacement de 20% des carburants classiques par des carburants de substitution pour le transport routier. Plus récemment, en juin 2001, au sommet de Göteborg, a été souligné le rôle important des biocarburants dans la lutte contre le changement climatique et le développement des énergies propres. Ces encouragements restaient au niveau de la déclaration d’intention faute de moyens administratifs et fiscaux pour bâtir une véritable stratégie. Depuis le 7 novembre 2001, les choses semblent évoluer : en effet, à cette date, le collège des Commissaires a adopté une communication sur les carburants de substitution pour les transports routiers et une série de mesures visant à promouvoir l’utilisation des biocarburants. De plus - et c’est ce qui est fondamental - cette communication était assortie de deux propositions de directives, l’une visant à promouvoir l’utilisation des biocarburants dans les transports, l’autre concernant la possibilité d’appliquer un taux d’accises réduit sur certaines huiles minérales qui contiennent des biocarburants et sur les biocarburants.

Cosmic Ether

CERN Document Server

Tomaschitz, R

1998-01-01

A prerelativistic approach to particle dynamics is explored in an expanding Robertson-Walker cosmology. The receding galactic background provides a distinguished frame of reference and a unique cosmic time. In this context the relativistic, purely geometric space-time concept is criticized. Physical space is regarded as a permeable medium, the cosmic ether, which effects the world-lines of particles and rays. We study in detail a Robertson-Walker universe with linear expansion factor and negatively curved, open three-space; we choose the permeability tensor of the ether in such a way that the semiclassical approximation is exact. Galactic red-shifts depend on the refractive index of the ether. In the local Minkowskian limit the ether causes a time variation of mass, which scales inversely proportional to cosmic time. In the globally geodesic rest frames of galactic observers the ether manifests itself in an unbounded speed of signal transfer, in bifurcations of world-lines, and in time inversion effects.

Fabrication and properties of poly(polyethylene glycol n-alkyl ether vinyl ether)s as polymeric phase change materials

International Nuclear Information System (INIS)

Pei, Dong-fang; Chen, Sai; Li, Shu-qin; Shi, Hai-feng; Li, Wei; Li, Xuan; Zhang, Xing-xiang

2016-01-01

A series of poly(polyethylene glycol n-alkyl ether vinyl ether)s (PC m E n VEs) with various lengths of alkyl chains and polyethylene glycol spacers as side chain (m = 16,18; n = 1,2) were synthesized via two steps. First, monomers-ethylene glycol hexadecyl ether vinyl ether (C 16 E 1 VE), ethylene glycol octadecyl ether vinyl ether (C 18 E 1 VE), diethylene glycol hexadecyl ether vinyl ether (C 16 E 2 VE) and diethylene glycol octadecyl ether vinyl ether (C 18 E 2 VE) were synthesized by a modified Williamson etherification. Then, four new types of phase change materials were successfully fabricated by a living cationic polymerization. Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) were employed to characterize their composition, thermal properties and crystallization behavior. The results show that, the side chains of PC 16 E 1 VE, PC 18 E 1 VE, PC 16 E 2 VE and PC 18 E 2 VE are in a hexagonal lattice, and the onset temperatures for melting of PC 16 E 1 VE, PC 18 E 1 VE, PC 16 E 2 VE and PC 18 E 2 VE are 39.8 °C, 37.4 °C, 51.0 °C and 48.9 °C, the onset temperatures for crystallization are 36.7 °C, 35.2 °C, 47.4 °C and 46.3 °C, respectively. The enthalpy changes of PC 18 E 1 VE, PC 16 E 2 VE and PC 18 E 2 VE are higher than 100 J/g; on the contrary, it is 96 J/g for PC 16 E 1 VE. The enthalpy decrease is no more than 11% after 10 heating and cooling cycles. The 5 wt% mass loss temperatures of PC 18 E 1 VE, PC 16 E 2 VE and PC 18 E 2 VE are higher than 300 °C; on the contrary, it’s 283 °C for PC 16 E 1 VE. Using a weak polarity, flexible alkyl ether chain (-OCH 2 CH 2 O-) as a spacer to link the main chain and side chain is conducive to the crystallization of the alkyl side chain. These new phase change materials can be applied in heat storage, energy conservation, and environmental protection.

Effect of nanograin-boundary networks generation on corrosion of carburized martensitic stainless steel.

Science.gov (United States)

Boonruang, Chatdanai; Thong-On, Atcharawadi; Kidkhunthod, Pinit

2018-02-02

Martensitic stainless steel parts used in carbonaceous atmosphere at high temperature are subject to corrosion which results in a large amount of lost energy and high repair and maintenance costs. This work therefore proposes a model for surface development and corrosion mechanism as a solution to reduce corrosion costs. The morphology, phase, and corrosion behavior of steel are investigated using GIXRD, XANES, and EIS. The results show formation of nanograin-boundary networks in the protective layer of martensitic stainless steel. This Cr 2 O 3 -Cr 7 C 3 nanograin mixture on the FeCr 2 O 4 layer causes ion transport which is the main reason for the corrosion reaction during carburizing of the steel. The results reveal the rate determining steps in the corrosion mechanism during carburizing of steel. These steps are the diffusion of uncharged active gases in the stagnant-gas layer over the steel surface followed by the conversion of C into C 4- and O into O 2- at the gas-oxide interface simultaneously with the migration of Cr 3+ from the metal-oxide interface to the gas-oxide interface. It is proposed that previous research on Al 2 O 3 coatings may be the solution to producing effective coatings that overcome the corrosion challenges discussed in this work.

Sliding wear characteristics of carburized steels and thermally refined steels implanted with nitrogen ions

International Nuclear Information System (INIS)

Terashima, Keiichi; Koda, Hiroyuki; Takeuchi, Eiichi.

1995-01-01

In order to concretely examine the application of surface reforming by ion implantation, nitrogen ion implantation was applied to the thermally refined steels S45C and SCM440 and the carburized steel SCM415, which are high versatile steels for mechanical structures, and their friction and wear characteristics were examined. The results are summarized as follows. In the surface-reformed material, in which nitrogen was implanted for the purpose of improving the seizure durability of the carburized steel, the load-frictional coefficient curve in lubricated sliding friction was similar to that of the material without implantation, but it was recognized that the load at which seizure occurred reached 2000 kgf or more, and as the amount of implantation was more, the material withstood higher load. In the lubricated sliding friction using a pin-ring type wear testing machine of the thermally refined steels and those to which implantation was applied, it was recognized that the specific wear amount was less in the implanted steels than in those without implantation. The results of the analysis of the implanted surface layers and the friction surfaces are reported. (K.I.)

Misconceptions about the ether

International Nuclear Information System (INIS)

Duffy, M.C.

1980-01-01

Several misconceptions concerning the ether concept and ether models are reviewed and clarified so that the relationship between modern ether theory and orthodox relativity may be better understood. The question of the ether's supposed superfluidity as a concept, and its status in modern physics remains to be answered. (author)

A Comprehensive Numerical Study on Effects of Natural Gas Composition on the Operation of an HCCI Engine Une étude numérique complète sur les effets de la composition du gaz naturel carburant sur le réglage d’un moteur HCCI

Directory of Open Access Journals (Sweden)

Jahanian O.

2011-11-01

éristiques d’auto-inflammation du mélange dans le cylindre et la performance du moteur HCCI. Cet article met l’accent sur l’influence de la composition du gaz naturel sur le fonctionnement du moteur en mode HCCI. Six différentes compositions de gaz naturel (y compris le méthane pur ont été examinées pour étudier les performances du moteur au moyen d’un modèle thermo-cinétique zéro-dimensionnel. Le code de simulation inclut la cinétique chimique détaillée de la combustion du gaz naturel, y compris le mécanisme étendu de Zeldovich pour évaluer les émissions de NOx. Les résultats ont été validés par comparaison avec des données expérimentales provenant d’autres travaux. La richesse et le taux de compression ont été maintenus constants, mais les effets de la vitesse du moteur et de la température initiale du mélange ont été étudiés. Les résultats montrent que la valeur maximale de la pression dans le cylindre et la température dépendent du nombre Wobbe du carburant. En outre, la puissance indiquée du moteur est linéairement liée au nombre Wobbe du carburant. Le travail indiqué brut, la pression moyenne indiquée brute et les NOx ont aussi été utilisés pour comparer les performances du moteur utilisant des carburants de compositions différentes.

EBSD analysis of tungsten-filament carburization during the hot-wire CVD of multi-walled carbon nanotubes

CSIR Research Space (South Africa)

Oliphant, CJ

2014-02-01

Full Text Available the carburization of tungsten filaments. During the synthesis, the W-filaments transform to W(sub2)C and WC.W-carbide growth followed a parabolic behavior corresponding to the diffusion of C as the rate-determining step. The grain size of W, W(sub2)C, and WC...

Gas carburizing end-discharge pusher furnaces for the automatic hardening of single gear components. Gasaufkohlungs-Durchstossanlagen mit automatischer Einzelhaertung von Getriebeteilen

Energy Technology Data Exchange (ETDEWEB)

Grassl, D; Washausen, R

1989-09-01

Apart from rotary hearth furnaces, end-discharge pusher furnaces are increasingly used for carburizing and hardening single components. These furnaces offer the following advantages: There is no limitation to the depth of case. The furnace zones can be controlled separately permitting carburizing to be optimized. The furnace can be designed to permit hardening of single components or quenching in batches. Process data relating to the components can be stored and called automatically (reproducibility of product quality). Heat treatment can be integrated in production control by process computer even if the furnace is installed separately. Regardless of what type of furnace is used, specific requirements have to be met to ensure reliable automatic discharge of single components. (orig./BWI).

Analysis of carburizing steel with lath bainite in matrix by magnetic method

Directory of Open Access Journals (Sweden)

Weiwu ZOU

2017-12-01

Full Text Available The cryogenic treatment is used to reduce the large amount of retained austenite in the steel infiltration layer which affects the hardness. The vibrating sample magnetometer (VSM and direct reading spectroscopy are combined to compare and analyze the organization structure status of the test carburizing steel after air-cooling and low temperature tempering (T at 453 K × 1 h, or after cryogenic treatment at 113 K × 30 min and low temperature tempering (T at 453 K × 1 h. The cryopreservation effect of the 1 203 K × 9 h carburizing air-cooled bainitic steel is carried out. The results show that both the effective hardening layer depths are about 1.35 mm. The retained austenite mass fractions of T and CT in the effective hardened layer are approximately 29.8% and 12.6%, respectively, and the highest hardnesses of the effective hardened layer of T and CT are 679 HV and 821 HV, respectively. The matrix structure is lath bainite, and the retained austenite mass fractions in the matrix are approximately 7.4% for T and 6.9% for CT, respectively, and both the hardnesses of the matrixes are approximately 430 HV. After the cryogenic treatment, the austenite content in the infiltration layer is effectively reduced, so that the maximum hardness of the hardened layer increases by 20% or more. It can be widely used because of the decreased material cost and remarkable economical benefit.

Biodiesel : la réglementation européenne et le débat sur son évolution

Directory of Open Access Journals (Sweden)

Dusser Philippe

2013-09-01

Full Text Available La réglementation communautaire sur les biocarburants a été mise en place à partir de 2003 pour répondre à un triple objectif : réduction des émissions de gaz à effet de serre, réduction de la dépendance énergétique, et soutien à la production agricole dans un contexte où 10 % des terres étaient obligatoirement gelées. Cette réglementation a été renforcée en 2009 dans le cadre du « paquet énergie » par l’introduction par la directive energie renouvelable d’un objectif obligatoire d’incorporation de 10 % d’énergie renouvelable dans les carburants à l’horizon 2020. Cette législation est complétée par une directive qualité des carburants qui impose une réduction de 6 % d’ici 2020 de l’empreinte carbone des carburants. La forte diésélisation du parc de véhicule en Europe a conduit à une rapide progression de la consommation de biodiesel (11 millions de tonnes dont 9 produites dans l’UE. L’huile de colza est la principale matière première du biodiesel. L’augmentation de la production de colza a permis de répondre à cette demande, tout en fournissant un coproduit protéique permettant de réduire significativement le déficit en protéines européen. Le débat sur l’impact du CASI (changement indirect d’affectation des sols des biocarburants, ainsi que celui sur l’équilibre alimentaire, a conduit la Commission européenne, 3 ans après avoir défini sa politique, à proposer de plafonner les carburants issus des cultures (1ere génération à 5 % et à introduire des « facteurs CASI » dans l’évaluation des effets de réduction des gaz à effets de serre. Cette proposition qui pourrait fortement remettre en cause le développement du biodiesel...et de la culture de colza fait à la date de rédaction de cet article (juillet 2013 l’objet de difficiles négociations à Bruxelles, dont l’issue est difficile à prédire.

Hydraulic Hybrid Propulsion for Heavy Vehicles: Combining the Simulation and Engine-In-the-Loop Techniques to Maximize the Fuel Economy and Emission Benefits Propulsion hybride hydraulique des poids lourds : une approche alliant les techniques de simulation et d’« Engine-In-the-loop » (EIL afin de maximiser les économies de carburant et les avantages en termes d’émissions

Directory of Open Access Journals (Sweden)

Filipi Z.

2009-09-01

échauffement climatique fournissent une forte motivation pour le développement de moyens de propulsion véhiculaires économes. Pour les camions, cette tâche est particulièrement difficile à accomplir du fait d’importantes contraintes de taille et de poids. L’hybridation est la seule approche qui puisse déboucher sur des progrès importants à court et moyen termes. En particulier, la configuration “hybride série” découple le moteur thermique des roues et permet une flexibilité complète dans le contrôle des points de fonctionnement moteur. De plus, la conversion et le stockage de l’énergie hydraulique fournissent une densité de puissance et un rendement excellents. Le défi technologique tient à la faible densité d’énergie de l’accumulateur hydraulique, et met en avant l’importance particulière du développement du gestionnaire de l’énergie. Il est communément admis qu’il faut maintenir le moteur au point de rendement maximum mais, si l’objectif ultime en terme énergétique consiste à optimiser drastiquement le rendement du moteur, ceci induit des phases transitoires fréquentes causant pour des moteurs diesels des effets opposés tant sur l’émission de particules que sur l’agrément de conduite. Par conséquent, nous proposons une méthodologie pour le superviseur d’énergie d’un système hybride, qui prend en compte 2 objectifs : la réduction de consommation et la réduction des émissions polluantes. Les économies de carburant sont prises en compte par une approche fondée sur la simulation, alors que l’étude de l’impact des phases transitoires du moteur sur les émissions de particules, est fondée sur un dispositif expérimental combinant modèles temps réel et moteur réel – l’EIL (Engine-In-the-Loop. Le dispositif EIL confirme que le contrôle de la répartition énergétique thermique/hydraulique de l’état de charge des batteries (SOC présente des avantages certains sur celui basé sur l’approche de contr

THE INFLUENCE OF GRINDING CONDITIONS ON THE DISTRIBUTION OF RESIDUAL STRESS IN THE SURFACE LAYER OF 17crni6-6 STEEL AFTER CARBURIZING

Directory of Open Access Journals (Sweden)

Jacek Sawicki

2017-06-01

Full Text Available This paper presents the results of a study aimed at determining the residual stress which results from developing the surface layer by low-pressure and conventional carburizing and grinding of 17CrNi6-6 steel. A synergistic effect of thermochemical and abrasive treatment was examined on ring samples used to study residual stress by Davidenkov’s method. Samples were subjected to vacuum carburizing and conventional carburizing, which was followed by grinding with a 38A60K8V aloxite grinding wheel and a CBN grinding wheel - RNB80/63B75V. The following cutting fluids were used during the grinding process: oil emulsion 5%, supply rate ca. 20 l/min, Micro5000 oil supplied at the minimum quantity lubrication (MQL of ca. 25 ml/h, dry machining. The study determined the effect of the type of grinding wheel and the cooling and lubricating agent on the distribution of residual stress in the sur-face layer. The best effects of grinding with respect to the residual stress were achieved with flood cooling with oil emulsion and grinding with a CBN grinding wheel.

Reproductive toxicity of the glycol ethers.

Science.gov (United States)

Hardin, B D

1983-06-01

The glycol ethers are an important and widely used class of solvents. Recent studies have demonstrated that ethylene glycol monomethyl ether (EGME), ethylene glycol dimethyl ether (EGdiME), ethylene glycol monoethyl ether (EGEE), and ethylene glycol monoethyl ether acetate (EGEEA) are teratogenic. Other studies have demonstrated that testicular atrophy or infertility follow treatment of males with EGME, ethylene glycol monomethyl ether acetate (EGMEA), EGEE, EGEEA, diethylene glycol dimethyl ether (diEGdiME), and diethylene glycol monoethyl ether (diEGEE). Experimental data are reviewed and structure-activity relationships are speculated upon.

Study of the machining of uranium carbide rods obtained by continuous casting under electronic bombardment; Etude de l'usinage de barreaux de carbure d'uranium obtenus par coulee continue sous bombardement electronique

Energy Technology Data Exchange (ETDEWEB)

Rousset, P.; Accary, A. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1965-07-01

The authors consider the various methods of machining uranium mono-carbide and compare them critically in the case of their application to uranium carbide obtained by fusion under an electronic bombardment and continuous casting. This study leads them to propose two mechanical machining methods: cylindrical rectification and center-less rectification, preceded by a preliminary roughing out of a cylinder, the latter appearing more suitable. A study of the machining yields as a function of the diameter of the rough bars and of the diameter of the finished rods has shown that an optimum value of the rough bar diameter exists for each value of the finished rod diameter. It is found that the yield increases as the diameter itself increases, this yield rising from 45 per cent to around 70 per cent as the diameter of the rough bars increases from 25-26 mm to 37-38 mm. (authors) [French] Les auteurs envisagent les differentes methodes d'usinage du monocarbure d'uranium et se livrent a une etude critique de celles-ci, dans le cas de leur application a l'usinage de barreaux de carbure d'uranium obtenus par fusion sous bombardement electronique et coulee continue. Cette etude les conduit a proposer deux methodes d'usinage mecanique: la rectification cylindrique et la rectification 'centerless', precedee d'un ebauchage par carottage, la seconde paraissant la plus appropriee. L'etude des rendements d'usinage en fonction du diametre des barreaux bruts et du diametre des barreaux finis, a mis en evidence une valeur optimale du diametre des barreaux bruts pour chaque valeur du diametre des barreaux usines. Elle a montre que le rendement croit lorsque le diametre croit lui-meme, ce rendement passant d'environ 45 pour cent a environ 70 pour cent, lorsque le diametre des barreaux bruts passe de 25-26 mm a 37-38 mm.

2665-IJBCS-Article-Issa Chaibou

African Journals Online (AJOL)

hp

Saverys et al., 2007). En plus de ces aspects environnementaux, les agro carburants présentent des avantages socio-économiques certains pour les pays en développement. Le Niger veut s'engager dans le développement de la filière des ...

Fuels distribution; Distribution des carburants

Energy Technology Data Exchange (ETDEWEB)

Le Brun, S.

2004-12-01

Although they have never stop to increase for thirty years, the shares of market of the large stores in the sales of fuels make nowadays a stop. Have the strict reorganizing the structure of the petroleum networks and their marketing strategy at last borne fruit? During the Petroleum Days have been discussed the evolvements of the service stations and of the consumer behaviour. (O.M.)

Product analyses and kinetic studies on gas phase oxidation of the fuel additive ethyl tert-butyl ether and its products; Produktanalysen und Kinetikuntersuchungen der Gasphasenoxidation des Kraftstoffadditivs Ethyl-tert-butylether und seiner Produkte

Energy Technology Data Exchange (ETDEWEB)

Becker, K H; Thuener, L

1997-04-01

The widespread use of the additive ETBE in gasoline leads to an increased release of this compound into the atmosphere via evaporation or exhaust fumes. In order to determine the influence of this additive on trace gas cycles it is first necessary to carry out studies on the degradation mechanisms and pertinent kinetic properties of this substance. The aim of the present study was to examine the degradation mechanisms of the fuel additive t-butyl ethyl ether under atmospheric conditions. The reactions of the main degradation products (t-butyl formiate and t-butyl acetate, together ca. 80%) were also studied in order to obtain as complete a picture of the degradation paths as possible. This was to permit an assessment of the influence of ETBE and its products on tropospheric trace gas cycles and ozone formation. [Deutsch] Bei haeufigem Zusatz von ETBE in Benzin wird diese Verbindung durch Verdampfung oder als Abgas verstaerkt in die Atmosphaere abgegeben. Um den Einfluss des Additivs auf die Spurengas-Kreislaeufe zu bestimmen, sind daher Untersuchungen noetig, um die Abbau-Mechanismen und die zugehoerigen kinetischen Daten zu ermitteln. Das Ziel dieser Arbeit ist die Untersuchung der Abbaumechanismen des Kraftstoffadditivs t-Butylethylether unter atmosphaerischen Bedingungen. Fuer eine moeglichst vollstaendige Analyse des Abbauweges werden auch die Reaktionen der Hauptabbauprodukte (t-Butylformiat und t-Butylacetat, zusammen etwa 80%) untersucht. Dadurch soll der Einfluss auf troposphaerische Spurengas-Kreislaeufe und auf die Ozonbildung von ETBE und seinen Produkten abgeschaetzt werden. (orig./SR)

Preparation and study of the nitrides and mixed carbide-nitrides of uranium and of plutonium; Preparation et etude des nitrures et carbonitrures d'uranium et de plutonium

Energy Technology Data Exchange (ETDEWEB)

Anselin, F [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1966-06-01

frittage. On a observe un effet benefique, mais non reproductible, de traces d'oxyde. Les meilleurs resultats ont ete obtenus pour UN pur, a 1600 C (96 pour cent de la densite theorique) a condition d'utiliser une poudre bien caracterisee. Le critere utilise est la largeur integrale des raies de diffraction X. Les composes UN et PuN sont entierement miscibles avec les carbures correspondants. Ceci permet de preparer par diffusion en phase solide, vers 1400 C, des carbonitrures de formule generale (U,Pu) (C,N). Le frittage de ces carbonitrures s'apparente a celui des carbures, si la teneur en azote est faible; en particulier le nickel est un additif de frittage efficace. Pour les teneurs elevees, le frittage est comparable a celui des nitrures purs.

Analyses of quenching process during turn-off of plasma electrolytic carburizing on carbon steel

International Nuclear Information System (INIS)

Wu, Jie; Liu, Run; Xue, Wenbin; Wang, Bin; Jin, Xiaoyue; Du, Jiancheng

2014-01-01

Highlights: • Cooling rate of carburized steel at the end of PEC treatment is measured. • The quench hardening in the fast or slow turn-off mode hardly takes place. • Decrease of the surface roughness during slow turn-off process is found. • A slow turn-off mode is recommended to replace the conventional turn-off mode. - Abstract: Plasma electrolytic carburizing (PEC) under different turn-off modes was employed to fabricate a hardening layer on carbon steel in glycerol solution without stirring at 380 V for 3 min. The quenching process in fast turn-off mode or slow turn-off mode of power supply was discussed. The temperature in the interior of steel and electron temperature in plasma discharge envelope during the quenching process were evaluated. It was found that the cooling rates of PEC samples in both turn-off modes were below 20 °C/s, because the vapor film boiling around the steel sample reduced the cooling rate greatly in terms of Leidenfrost effect. Thus the quench hardening hardly took place, though the slow turn-off mode slightly decreased the surface roughness of PEC steel. At the end of PEC treatment, the fast turn-off mode used widely at present cannot enhance the surface hardness by quench hardening, and the slow turn-off mode was recommended in order to protect the electronic devices against a large current surge

Microbial degradation of 4-monobrominated diphenyl ether with anaerobic sludge

International Nuclear Information System (INIS)

Shih, Yang-hsin; Chou, Hsi-Ling; Peng, Yu-Huei

2012-01-01

Highlights: ► BDE-3 was degraded with two anaerobes in different rates. ► Glucose addition augment the debromination efficiencies. ► Hydrogen gas was detected and relative microbes were identified. ► Extra-carbon source enhanced degradation partial due to H 2 -generation bacteria. - Abstract: Polybrominated diphenyl ethers (PBDEs) are widely used flame retardant additives for many plastic and electronic products. Owing to their ubiquitous distribution in the environment, multiple toxicity to humans, and increasing accumulation in the environment, the fate of PBDEs is of serious concern for public safety. In this study, the degradation of 4-monobrominated diphenyl ether (BDE-3) in anaerobic sludge and the effect of carbon source addition were investigated. BDE-3 can be degraded by two different anaerobic sludge samples. The by-products, diphenyl ether (DE) and bromide ions, were monitored, indicating the reaction of debromination within these anaerobic samples. Co-metabolism with glucose facilitated BDE-3 biodegradation in terms of kinetics and efficiency in the Jhongsing sludge. Through the pattern of amplified 16S rRNA gene fragments in denatured gradient gel electrophoresis (DGGE), the composition of the microbial community was analyzed. Most of the predominant microbes were novel species. The fragments enriched in BDE-3-degrading anaerobic sludge samples are presumably Clostridium sp. This enrichment coincides with the H 2 gas generation and the facilitation of debromination during the degradation process. Findings of this study provide better understanding of the biodegradation of brominated DEs and can facilitate the prediction of the fate of PBDEs in the environment.

Medium temperature reaction between lanthanide and actinide carbides and hydrogen; Reaction a temperature moyenne entre les monocarbures de lanthanides et d'actinides et l'hydrogene

Energy Technology Data Exchange (ETDEWEB)

Dean, G; Lorenzelli, R; Pascard, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1964-07-01

Hydrogen is fixed reversibly by the lanthanide and actinide mono carbides in the range 25 - 400 C, as for pure corresponding metals. Hydrogen goes into the carbides lattice through carbon vacancies and the total fixed amount is approximately equal to two hydrogen atoms per initial vacancy. Final products c.n thus be considered as carbo-hydrides of general formula M(C{sub 1-x}, H{sub 2x}). The primitive CFC, NaCl type, structure remains unchanged but expands strongly in the case of actinide carbides. With lanthanide carbides, hydrogenation induces a phase transformation with reappearance of the metal structure (HCP). Hydrogen decomposition pressures of all the studied carbo-hydrides are greater than those of the corresponding di-hydrides. (authors) [French] Les monocarbures d'actinides et de lanthanides fixent reversiblement de l'hydrogene a temperature peu elevee, a peu pres dans les memes conditions que les metaux purs correspondants. L'hydrogene penetre dans le reseau des carbures par l'intermediaire des lacunes de carbone, et la quantite totale fixee est approximativement egale a deux atomes d'hydrogene par lacune initiale. Les produits obtenus peuvent donc etre consideres comme des carbohydrures de formule generale M(C{sub 1-x}, H{sub 2x}). La structure d'origine CFC, type NaCl est conservee, mais avec une forte expansion, dans le cas des carbures d'actinides. En revanche, l'hydrogenation entraine un changement de phase cristalline avec retour a la structure du metal (HC) pour les carbures de lanthanides. Tous les carbohydrures etudies ont des tensions de decomposition en hydrogene superieures a celles des dihydrures correspondants. (auteurs)

Exogenous ether lipids predominantly target mitochondria.

Directory of Open Access Journals (Sweden)

Lars Kuerschner

Full Text Available Ether lipids are ubiquitous constituents of cellular membranes with no discrete cell biological function assigned yet. Using fluorescent polyene-ether lipids we analyzed their intracellular distribution in living cells by microscopy. Mitochondria and the endoplasmic reticulum accumulated high amounts of ether-phosphatidylcholine and ether-phosphatidylethanolamine. Both lipids were specifically labeled using the corresponding lyso-ether lipids, which we established as supreme precursors for lipid tagging. Polyfosine, a fluorescent analogue of the anti-neoplastic ether lipid edelfosine, accumulated to mitochondria and induced morphological changes and cellular apoptosis. These data indicate that edelfosine could exert its pro-apoptotic power by targeting and damaging mitochondria and thereby inducing cellular apoptosis. In general, this study implies an important role of mitochondria in ether lipid metabolism and intracellular ether lipid trafficking.

Ether formulations of relativity

International Nuclear Information System (INIS)

Duffy, M.C.

1980-01-01

Contemporary ether theories are surveyed and criticised, especially those formally identical to orthodox Relativity. The historical development of Relativity, Special and General, in terms of an ether, is briefly indicated. Classical interpretations of Generalized Relativity using ether are compared to Euclidean formulations using a background space. The history of a sub-group of theories, formulating a 'new' Relativity involving modified transforms, is outlined. According to the theory with which they agree, recent supposed detections of drift are classified and criticised. Cosmological evidence suggesting an ether is mentioned. Only ether theories formally identical to Relativity have been published in depth. They stand criticised as being contrary to the positivist spirit. The history of mechanical analogues is traced, from Hartley's representing gravitating matter as spherical standing waves, to recent suggestions that vortex-sponge might model electromagnetic, quantum, uncertainty and faster-than-light phenomena. Contemporary theories are particular physical theories, themselves 'second interpretations' of a primary mathematical model. Mechanical analogues are auxiliary, not necessary, to other theory, disclosing relationships between classical and non-classical descriptions of assemblies charging state. The ether-relativity polemic, part of a broader dispute about relativity, is founded on mistaken conceptions of the roles of mathematical and physical models, mechanical analogues; and a distored view of history, which indicates that ether theories have become relativistic. (author)

Design, Fabrication and Performance of Boron-Carbide Control Elements; Conception, Fabrication et Comportement de Lames de Commande en Carbure de Bore; Raschety, izgotovlenie i kharakteristiki reguliruyushchikh sterzhnej. Iz karbida Bora; Proyecto, Elaboracion y Rendimiento de Elementos de Control de Carburo de Boro

Energy Technology Data Exchange (ETDEWEB)

Brammer, H. A.; Jacobson, J. [General Electric Company, San Jose, CA (United States)

1964-06-15

A control blade design, incorporating boron-carbide (B{sub 4}C) in stainless-steel tubes, was introduced into service in boiling water reactors in April 1961. Since that time this blade has become the standard reference control element in General Electric boiling-water reactors, replacing the 2% boron-stainless-steel blades previously used. The blades consist of a sheathed, cruciform array of small vertical stainless-steel tubes filled with compacted boron-carbide powder. The boron-carbide powder is confined longitudinally into several independent compartments by swaging over ball bearings located inside the tubes. The development and use of boron-carbide control rods is discussed in five phases: 1. Summary of experience with boron-steel blades and reasons for transition to boron-carbide control; 2. Design of the boron-carbide blade, beginning with developmental experiments, including early measurements performed in the AEC ''Control Rod Material and Development Program'' at the Vallecitos Atomic Laboratory, through a description of the final control blade configuration; 3. Fabrication of the blades and quality control procedures; 4. Results of confirmatory pre-operational mechanical and reactivity testing; and 5. Post-operational experience with the blades, including information on the results of mechanical inspection and reactivity testing after two years of reactor service. (author) [French] Un modele de lame de commande en carbure de bore (B{sub 4}C) a ete mis en place dans des reacteurs a eau bouillante en avril 1961. Depuis lors, cette lame est devenue l 'element de commande temoin classique dans les reacteurs a eau bouillante de la General Electric et a remplace les lames en acier inoxydable a 2% de bore utilisees auparavant. Ces lames consistent en un assemblage gaine cruciforme comprenant de petits tubes d'acier inoxydable verticaux remplis de poudre de carbure de bore agglomeree. Dans le sens de la longueur, cette poudre est enfermee dans plusieurs

Study of Effect of Quenching Deformation Influenced by 17CrNiMo6 Gear Shaft of Carburization

Science.gov (United States)

Pang, Zirui; Yu, Shenjun; Xu, Jinwu

The 17CrNiMo6 steel is mainly used for the gear shaft of large modulus in many fields of heavy industry such as mining, transit, hoist, forging and so on[1]. The size of addendum circle and common normal line is changed a lot beyond the tolerance because of the long time of carburizing process and the out-of-step structural stress and thermal stress during the quenching process. And thus the posterior grinding efficiency and quality are influenced. In the paper comparison and analysis of the deformation affected by solid and hollow gear shafts were done and the methods of simulation and practice were both used. The results are as follows: the deformation of gear shaft was small before and after carburizing while that of gear shaft was large before and after quenching because of different cooling velocity, structure and hardness of each position. And the deformation of hollow was much smaller than that of solid. Therefore, if the hollow gear shaft is used, the waste of material will be decreased, and finishing cost will be reduced, and thus the technology of heat treatment will be optimized.

Ether the nothing that connects everything

CERN Document Server

Milutis, Joe

2006-01-01

In Ether, the histories of the unseen merge with discussions of the technology of electromagnetism. Navigating more than three hundred years of the ether''s cultural and artistic history, Joe Milutis reveals its continuous reinvention and tangible impact without ever losing sight of its ephemeral, elusive nature. The true meaning of ether, Milutis suggests, may be that it can never be fully grasped.

Usage of the word 'ether'

International Nuclear Information System (INIS)

Duffy, M.C.

1980-01-01

Confusion has been caused by scientists using the one word 'ether' to classify models differing from each other in important respects. Major roles assigned to the word are examined, and the nature of modern ether theories surveyed. The part played by the several meanings attached to the word, in the ether concept, is outlined. (author)

Optical Engines as Representative Tools in the Development of New Combustion Engine Concepts Moteurs transparents comme outils représentatifs dans le développement de nouveaux concepts des moteurs à combustion interne

Directory of Open Access Journals (Sweden)

Kashdan J.

2011-11-01

de s’assurer que le fonctionnement des moteurs transparents est tout à fait comparable et représentatif de celui des moteurs standards (opaques. Une comparaison du comportement de la combustion et des émissions des moteurs transparents et opaques a été réalisée. L’objectif était d’étudier les différences principales entre le moteur transparent et le moteur opaque et de comprendre comment ces différences peuvent influencer les phases de préparation du mélange, la combustion et la formation de polluants. Les résultats expérimentaux révèlent l’influence significative des différences liées à la température des parois de la chambre de combustion. Des mesures de la température des parois ont été effectuées par la technique de phosphorescence induite par laser. Ces mesures ont permis de définir des stratégies de fonctionnement moteur permettant de compenser les différences de température de paroi entre les deux moteurs. En outre, l’impact des différences géométriques des chambres a été investiguée. La réhausse piston peut subir soit un chargement mécanique dynamique (effets de compression ou de traction soit une expansion thermique. Ces effets peuvent faire varier le taux de compression effectif. La charge admise dans les moteurs transparents est souvent diluée par de l’EGR simulé au lieu d’utiliser l’EGR réel. Dans les conditions de Diesel LTC, une comparaison a été effectuée entre l’utilisation d’EGR réel et d’EGR simulé par un gaz diluant pur. Enfin, les carburants mono-composants (carburants purs sont souvent utilisés dans les moteurs Diesel transparents en raison des contraintes imposées par l’utilisation de techniques de diagnostics optiques. Cependant, les carburants purs diffèrent quelque peu des carburants Diesel réels, en particulier au travers de leur indice de cétane et de leur volatilité. Ces différences peuvent influencer fortement le comportement de la combustion et des �

The failure of poly (ether ether ketone) in high speed contacts

Science.gov (United States)

Briscoe, B. J.; Stuart, B. H.; Sebastian, S.; Tweedale, P. J.

1993-04-01

The paper describes an experimental study, with an associated analysis incorporating supplementary data, of the anti-boundary lubricating action of an alkane-aliphatic carboxylic acid lubricant system in a poly (ether ether ketone)-mild steel contact. The experiments involve progressively increasing the load in a contact formed between a polymer plate and a rotating steel shaft and estimating the frictional work dissipated. Scuffing is identified when a rapid increase in frictional work is noted at a characteristic normal load. It is shown that the additive induces premature scuffing. Subsidiary data is provided using Raman spectroscopy and hardness probes, and confirms that certain additives such as decanoic acid and dodecylamine will induce surface plasticization in poly (ether ether ketone). The trends in the frictional data have been interpreted using the adhesive model of friction in conjunction with temperature-dependent interfacial theology and bulk mechanical property data. It is proposed that the scuffing process is induced prematurely as a consequence of excessive additive-induced subsurface plasticization. Restricted surface plasticization in this system provides an enhanced self-lubricating capacity.

Development of CSS-42L{trademark}, a high performance carburizing stainless steel for high temperature aerospace applications

Energy Technology Data Exchange (ETDEWEB)

Burrier, H.I.; Milam, L. [Timken Co., Canton, OH (United States); Tomasello, C.M.; Balliett, S.A.; Maloney, J.L. [Latrobe Steel Co., Latrobe, PA (United States); Ogden, W.P. [MPB Corp., Lebanon, NH (United States)

1998-12-31

Today`s aerospace engineering challenges demand materials which can operate under conditions of temperature extremes, high loads and harsh, corrosive environments. This paper presents a technical overview of the on-going development of CSS-42L (US Patent No. 5,424,028). This alloy is a case-carburizable, stainless steel alloy suitable for use in applications up to 427 C, particularly suited to high performance rolling element bearings, gears, shafts and fasteners. The nominal chemistry of CSS-42L includes: (by weight) 0.12% carbon, 14.0% chromium, 0.60% vanadium, 2.0% nickel, 4.75% molybdenum and 12.5% cobalt. Careful balancing of these components combined with VIM-VAR melting produces an alloy that can be carburized and heat treated to achieve a high surface hardness (>58 HRC at 1mm (0.040 in) depth) with excellent corrosion resistance. The hot hardness of the carburized case is equal to or better than all competitive grades, exceeding 60 HRC at 427 C. The fracture toughness and impact resistance of the heat treated core material have likewise been evaluated in detail and found to be better than M50-NiL steel. The corrosion resistance has been shown to be equivalent to that of 440C steel in tests performed to date.

Contribution to the study of gaseous Carburization of Uranium; Contribucion al estudio de la Carburacion gaesosa del uranio

Energy Technology Data Exchange (ETDEWEB)

Esteban Hernandez, J A; Jimenez Moreno, J M; Villota Ruiz, P de

1966-07-01

Thermal decomposition of uranium hydride powder obtained by hydrogenation of uranium turnings is studied on the first part of this paper. Carburization of the uranium hydride or metallic uranium powder with methane is studied in the second part. A method of uranium monocarbide fabrication under static atmosphere is described. On this method hydrogen is removed by means of an uranium getter. (Author) 6 refs.

Laws of alloyed cementite particles nucleation during heat-resistant steels carburizing

Directory of Open Access Journals (Sweden)

M. Yu. Semenov

2014-01-01

Full Text Available The article considers a problem analyzing a nucleation of cementite type carbides in carburized heat-resistant steels for the turbofan engines gear wheels.The verification of previously hypothesized mechanism of dislocation nucleation particles chromium-alloyed cementite during process of carburizing was accepted as an objective of the work.As a methodological basis of this paper were accepted the numerical experiments based on the kinetic theory of nucleation, as well as on the known results of experimental studies.According to the kinetic theory of nucleation, a new phase in the solid solutions take place in the defects of the crystal structure of the metal such as inter-grain boundaries and dislocations clusters. A principle feature of the inter-grain boundary mechanism of nucleation is formation of carbide lattice. It is of great practical interest because the cementite lattice drops mechanical properties of hardened parts.According to the experimental studies, the average chromium concentration in the alloyed cementite twice exceeds its Cr content in the heat-resistant steels. Furthermore, the areas of abnormally high (more than ten times in comparison with the average content chromium concentration in cementite have been experimentally revealed.Numerical experiments have revealed that the nucleation of cementite particles alloyed with chromium (chromium concentration of 3% or more occurs, mainly, by the dislocation mechanism on the concentration fluctuations of the alloying element. According to calculations, an obligatory prerequisite to start an active nucleation process of new phase in the solid solution is a local increase of the chromium concentration up to 40%.Despite the lack of physical prerequisites for the formation of chromium precipitates, this phenomenon is explained by a strong chemical affinity of chromium and carbon, causing diffusion of chromium atoms in the region of the carbon atoms clusters. The formation of carbon

Molybdenum acetate like precursor of molybdenum carburized supported on alumina: a catalyst for hydrogenation reactions

International Nuclear Information System (INIS)

Petkovic, Lucia M; Parra, Ruben D; Marquez Manuel; Larsen, Gustavo

1994-01-01

The stability of the Al203 supported dimers under relatively high temperatures and hydrocarbon/H2 (carburizing) atmospheres is reported also, it has been developed a new method for Mo2 loading of the support based on the wet impregnation of the latter. Since carbided Mo is active for hydrogenations, the isobutene/H2 has been chosen as the probe reaction. Al203 supported Mo2(Ac)4 results in a catalyst active for isobutene hydrogenation after treatment with a H2/C2H6 2:1 mixture at 753 k

Relationship between carburization and zero-applied-stress creep dilation in Alloy 800H and Hastelloy X

International Nuclear Information System (INIS)

Inouye, H.; Rittenhouse, P.L.

1981-01-01

Typical HTGR candidate alloys can carburize when exposed to simulated service environments. The carbon concentration gradients so formed give rise to internal stresses which could cause dilation. Studies performed with Hastelloy X and Alloy 800H showed that dilations of up to almost 1% can occur at 1000 0 C when carbon pickup is high. Dilation was normally observed only when the carbon increase was >1000 μg/cm 2 and ceased when diffusing carbon reached the center of the specimen. (Auth.)

Contribution to the study of the hydrolysis of uranium carbides (1963); Contribution a l'etude de l'hydrolyse des carbures d'uranium (1963)

Energy Technology Data Exchange (ETDEWEB)

Spitz, J [Commisariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1963-06-15

The hydrolysis of uranium monocarbide in neutral or acid medium leads to the formation of a complex mixture of hydrogen and hydrocarbons mostly saturated. When UC-U alloys are dissolved in hydrochloric-phosphoric medium, the free uranium contents can be determined with good accuracy from the composition of the gaseous phase. The hydrolysis of mixtures of uranium mono - and dicarbide in neutral or acid medium, leads to the formation of a complex mixture of hydrogen and gaseous and condensed hydrocarbons, the composition of which is principally dependent upon the UC{sub 2} content. The reaction mechanisms which are presented in this paper for the hydrolysis of UC and UC{sub 2} provide account for all experimental observations. (author) [French] L'hydrolyse en milieu neutre ou acide du monocarbure d'uranium conduit a la formation d'un melange complexe d'hydrogene et d'hydrocarbures, satures en grande majorite. L'attaque en milieu chlorhydrique-phosphorique des alliages UC-U permet la determination avec une bonne precision, des teneurs en uranium libre a partir de la composition des gaz degages. L'hydrolyse en milieu neutre ou acide des melanges de mono - et dicarbure d'uranium conduit a la formation d'un melange complexe d'hydrogene et d'hydrocarbures gazeux et condenses, dont la composition est essentiellement fonction de la teneur en UC{sub 2}. Les mecanismes reactionnels proposes pour l'hydrolyse de UC et UC{sub 2} rendent compte de tous les faits experimentaux observes. (auteur)

Application of experiment planning during investigation of cementation process in solid carburizers

International Nuclear Information System (INIS)

Lisenkov, A.N.; Denisov, V.M.; Prigozhina, E.L.

1981-01-01

A mathematical model of cementation process in solid carburizirs is obtained, the most effective contents of carburizers are chosen. Specimens are produced out of St20, 12KhN3A, 40Kh13, KhVG steels. It is shown that specimens of St20 and 12KhN3A steels have the higher depth of cementated layer, specimens made of 40Kh13 and KhVG steels-the lower depth. It is shown that the quality of cementated layer structure at recommended regimes improved, cementated layer depth for low-carbon steels changed a little and for tool steels increased infficiently: for KhVG steel in 2-3 times for 40Kh13 steel in 1.5-2.5 times

Silane Cross-Linked Sulfonted Poly(Ether Ketone/Ether Benzimidazoles for Fuel Cell Applications

Directory of Open Access Journals (Sweden)

Zilu Yao

2017-11-01

Full Text Available γ-(2,3-epoxypropoxy propyltrimethoxysilane (KH-560 was incorporated in various proportions into side-chain-type sulfonated poly(ether ketone/ether benzimidazole (SPEKEBI as a crosslinker, to make membranes with high ion exchange capacities and excellent performance for direct methanol fuel cells (DMFCs. Systematical measurements including Fourier transform infrared (FT-IR, scanning electron microscopy-energy-dispersive and X-ray photoelectron spectroscopy (XPS proved the complete disappearance of epoxy groups in KH-560 and the existence of Si in the membranes. The resulting membranes showed increased mechanical strength and thermal stability compared to the unmodified sulfonated poly(ether ketone/ether benzimidazole membrane in appropriate doping amount. Meanwhile, the methanol permeability has decreased, leading to the increase of relative selectivities of SPEKEBI-x-SiO2 membranes. Furthermore, the H2/O2 cell performance of SPEKEBI-2.5-SiO2 membrane showed a much higher peak power density compared with the pure SPEKEBI memrbrane.

Critical properties of some aliphatic symmetrical ethers

International Nuclear Information System (INIS)

Nikitin, Eugene D.; Popov, Alexander P.; Bogatishcheva, Nataliya S.

2014-01-01

Highlights: • Critical properties of simple aliphatic ethers were measured. • The ethers decompose at near-critical temperatures. • Pulse-heating method with short residence times was used. -- Abstract: The critical temperatures T c and the critical pressures p c of dihexyl, dioctyl, and didecyl ethers have been measured. According to the measurements, the coordinates of the critical points are T c = (665 ± 7) K, p c = (1.44 ± 0.04) MPa for dihexyl ether, T c = (723 ± 7) K, p c = (1.19 ± 0.04) MPa for dioctyl ether, and T c = (768 ± 8) K, p c = (1.03 ± 0.03) MPa for didecyl ether. All the ethers studied degrade chemically at near-critical temperatures. A pulse-heating method applicable to measuring the critical properties of thermally unstable compounds has been used. The times from the beginning of a heating pulse to the moment of reaching the critical temperature were from 0.06 to 0.46 ms. The short residence times provide little decomposition of the substances in the course of the experiments. The critical properties of the ethers investigated in this work have been discussed together with those of methyl to butyl ethers. The experimental critical constants of the ethers have been compared with those estimated by the group-contribution methods of Wilson and Jasperson and Marrero and Gani. The Wilson/Jasperson method provides a better estimation of the critical temperatures and pressures of simple aliphatic ethers in comparison with the Marrero/Gani method if reliable normal boiling temperatures are used in the method of Wilson and Jasperson

Radiation-induced cationic curing of vinyl ethers

International Nuclear Information System (INIS)

Lapin, S.C.

1992-01-01

Recently there has been an increasing interest in nonacrylate radiation-curable coatings. Vinyl ethers are particularly reactive under cationic polymerization reaction conditions. The high efficiency of the photoacid initiators combined with the high reactivity of vinyl ether monomers makes this a potentially very useful system. This chapter discusses the preparation of vinyl ethers, introduces vinyl ether-functional monomers and oligomers, describes radiation-induced cationic polymerization of vinyl ethers, and discusses various coating systems. Throughout the chapter, an emphasis is placed on radiation-curable coating applications. 64 refs., 5 figs., 11 tabs

Poly (ether ether ketone) membranes for fuel cells

International Nuclear Information System (INIS)

Marrero, Jacqueline C.; Gomes, Ailton de S.; Filho, Jose C.D.; Hui, Wang S.; Oliveira, Vivianna S. de

2015-01-01

Polymeric membranes were developed using a SPEEK polymer matrix (sulphonated poly (ether ether ketone)), containing hygroscopic particles of zirconia (Zr) (incorporated by sol-gel method), for use as electrolyte membranes in fuel cells. SPEEK with different sulfonation degrees were used: 63 and 86%. The thermal analysis (TGA and DSC) was carried out to characterize the membranes and electrochemical impedance spectroscopy (EIS) was carried out to evaluating the proton conductivity of the membranes. Additional analysis were underway in order to characterize these membranes, which include: X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) in order to evaluate the influence of zirconia and sulfonation degree on the properties of the membranes. (author)

Ion-Selective Ionic Polymer Metal Composite (IPMC) actuator based on crown ether containing sulfonated Poly(Arylene Ether Ketone)

NARCIS (Netherlands)

Tas, S.; Zoetebier, B.; Sukas, O.S.; Bayraktar, M.; Hempenius, M.; Vancso, G.J.; Nijmeijer, K.

2017-01-01

This study introduces the concept of ion selective actuation in polymer metal composite actuators, employing crown ether bearing aromatic polyether materials. For this purpose, sulfonated poly(arylene ether ketone) (SPAEK) and crown ether containing SPAEK with molar masses suitable for membrane

Utilisation des huiles végétales et de leurs produits de transestérification comme carburants Diesel Use of Vegetable Oils and Their Transesterification Products As Diesel Fuels

Directory of Open Access Journals (Sweden)

Gateau P.

2006-11-01

Full Text Available L'utilisation d'huiles végétales et de leurs dérivés comme carburants Diesel a fait l'objet, depuis 1981, de plusieurs études financées par l'Agence Française pour la Maîtrise de l'Energie (AFME et réalisées par l'institut Français du Pétrole (lFP en collaboration avec Elf Renault, le Centre d'Etudes et d'Expérimentation du Machinisme Agricole Tropical (CEEMAT et l'institut de Recherches pour les Huiles et Oléagineux (IRHO. Ce document rassemble les résultats obtenus au banc d'essai sur plusieurs types de moteurs représentant un assez large éventail d'applications, depuis le motoculteur utilisé en agriculture africaine jusqu'au moteur classique de tracteur ou de camion. Deux types de produits ont été examinés : les huiles végétales elles-mêmes employées pures ou en mélange au gazole, et les esters méthyliques de ces huiles utilisés tels quels. Lors d'un fonctionnement de courte durée les huiles aussi bien que les esters conduisent globalement à un fonctionnement satisfaisant du moteur; les pertes de performances par rapport au gazole restent modérées voire imperceptibles. Les seuls problèmes dans ce cas concernent la mise en oeuvre, difficile avec les huiles en raison de leur très forte viscosité, beaucoup plus aisée avec les esters. En endurance, l'inconvénient majeur des huiles végétales et de leurs dérivés concerne la formation de dépôts au nez des injecteurs. Sur les moteurs rustiques à préchambre (type Hatz ce phénomène reste limité puisqu'il a été possible de conduire, sans incident, un ensemble d'essais d'endurance de 1100 h avec différents types d'huiles pures (arachide, coton, palme. Sur les moteurs à Injection directe la formation de dépôts constitue une très sérieuse contrainte puisqu'elle conduit pratiquement à proscrire l'utilisation d'huiles même en mélange (25 ou 50 % dans le gazole. Les esters peuvent alors être proposés à condition qu'un certain nombre de pr

Study of the 1.25Cr-1Mo-0.25V steel microstructure after a carburization phenomenon

Energy Technology Data Exchange (ETDEWEB)

Simonetti, S., E-mail: ssimonet@uns.edu.ar [Departamento de Fisica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Departamentos de Ciencias Basicas e Ingenieria Mecanica, Universidad Tecnologica Nacional, 11 de Abril 461, 8000 Bahia Blanca (Argentina); Lanz, C. [Departamento de Ingenieria, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Brizuela, G.; Juan, A. [Departamento de Fisica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

2010-08-20

We studied the changes in the structure and carbide particle size in 1.25Cr-1Mo-0.25V steel under 600 deg. C and 168 MPa, after 4000 h service. We used microscopy and microanalysis techniques to analyze the carbide particles. We performed a complementary theoretical study on the chemical bonding and electronic structure of the carbide-Fe matrix interaction. The results contribute to the understanding of the changes in the alloy microstructure caused by the carburization phenomenon.

All solid supercapacitor based on polyaniline and crosslinked sulfonated poly[ether ether ketone

International Nuclear Information System (INIS)

Sivaraman, P.; Kushwaha, R.K.; Shashidhara, K.; Hande, V.R.; Thakur, A.P.; Samui, A.B.; Khandpekar, M.M.

2010-01-01

All solid supercapacitor based on polyaniline (PANI) and crosslinked sulfonated poly[ether ether ketone] (XSPEEK,) is reported in this paper. The crosslinker used for sulfonated poly[ether ether ketone] (SPEEK) is 1,4-bis(hydroxymethyl) benzene. The XSPEEK is used as both solid electrolyte and separator membrane. Supercapacitors are fabricated using various PANI/XSPEEK weight ratios. These are characterized by cyclic voltammetry and galvanostatic charge-discharge studies. The supercapacitor with PANI/XSPEEK weight ratio 1:0.5, exhibit a specific capacitance of 480 F g -1 of PANI. To the best of authors' knowledge, the value reported here is the highest for a supercapacitor based on a proton conducting solid polymer electrolyte and PANI. Detailed electrochemical impedance spectroscopy analysis is carried out. The analysis shows that the complex capacitance of the supercapacitor depends on the XSPEEK content. The time constant (t 0 ), derived from the imaginary part of complex capacitance decreases with increase in the XSPEEK content in the supercapacitor. Cycle life characteristics of the supercapacitor show a decrease in specific capacitance during initial cycles and get stabilized during later cycles.

Hydrogen storage by functionalised Poly(ether ether ketone)

Energy Technology Data Exchange (ETDEWEB)

Pedicini, R.; Giacoppo, G.; Carbone, A.; Passalacqua, E. [CNR-ITAE, Messina (Italy). Inst. for Advanced Energy Technologies

2010-07-01

In this work a functionalised polymer was studied as potential material for hydrogen storage in solid state. A Poly(ether ether ketone) (PEEK) matrix was modified by a manganese oxide in situ formation. Here we report the functionalisation process and the preliminary results on hydrogen storage capability of the synthesised polymer. The polymer was characterized by Scanning Electron Microscopy, X-ray diffraction, Transmission Electron Microscopy and Gravimetric Hydrogen Adsorption measurements. In the functionalised PEEK, morphological changes occur as a function of oxide precursor concentration and reaction time. Promising results by gravimetric measurements were obtained with a hydrogen sorption of 0.24%wt/wt at 50 C and 60 bar, moreover, reversibility hydrogen adsorption and desorption in a wide range of both temperature and pressure was confirmed. (orig.)

Étude de la restauration des caractéristiques de tubes de four de vapocraquage en Manaurite 36 XS Study of the Restoration of the Characteristics of Steam-Cracker Tubes Made of Manaurite 36 Xs

Directory of Open Access Journals (Sweden)

Ropital F.

2006-11-01

Full Text Available Le vieillissement de tubes de four en Manaurite 36XS d'une unité de vapocraquage se traduit par une précipitation et une coalescence de carbures aux joints de grains, une évolution locale de la composition chimique et une forte diminution de la ductilité. Des traitements thermiques appropriés, dont l'efficacité est suivie par microanalyse et par l'évolution des propriétés mécaniques, permettent de restaurer en quasi totalité les caractéristiques de l'acier. Après détermination des conditions en laboratoire, un essai très positif a été réalisé sur tube de four avec des moyens utilisables sur chantier. The aging of Manaurite 36 XS tubes in a steam-cracking unit results in the precipitation and coalescence of carbides at grain boundaries, a local variation in the chemical composition and a strong decrease in ductility. Appropriate thermal treatments, whose efficiency is monitored by microanalysis and by the variation of mechanical properties, enable almost all the characteristics of the steel to be restored. After laboratory conditions were determined, a very positive test was performed on a cracker tube with means that can be used in the field.

Contribution de la pyrolyse des produits lourds à la valorisation des pétroles bruts Contribution of the Pyrolysis of Heavy Products to the Upgrading of Crude Oils

Directory of Open Access Journals (Sweden)

Charlot J. C.

2006-11-01

Full Text Available Le raffineur achète des pétroles bruts, de différentes qualités et d'origines variées, et il fabrique un certain nombre de produits répondant à des spécifications de qualité pour les vendre dans des proportions correspondant aux besoins du marché. Il est nécessaire pour cela d'assurer l'équilibre général entre l'approvisionnement en brut et la demande du marché en produits finis. Les facteurs traduisant l'évolution des pétroles bruts (souci de diversification géographique et politique, désir des producteurs de traiter les bruts faciles et d'exporter les lourds, compétitivité de plus en plus grande des bruts non-conventionnels, grande disponibilité d'huiles lourdes montrent l'alourdissement progressif des approvisionnements. L'enchérissement des produits pétroliers provoque de plus en plus un allègement des besoins du marché (légère augmentation des carburants, baisse des distillats moyens, chute importante des fuels lourds. Du fait de l'alourdissement des bruts conventionnels, de la grande disponibilité des huiles lourdes et de l'allègement considérable du marché des produits finis, il devient nécessaire d'utiliser des charges de plus en plus lourdes dans les procédés de conversion. La production d'oléfines peut s'effectuer à partir d'une gamme très large de coupes pétrolières, mais lorsqu'on cherche à alourdir la charge des unités de pyrolyse, il faut se poser les questions suivantes : - quelle est la souplesse des unités existantes et à venir par rapport à la charge ? - quelle est la limite industrielle et l'alourdissement de la charge ? - quel est le rôle des impuretés sur le fonctionnement des unités ? - quels sont les problèmes technologiques posés par le traitement de ces charges ? - qu'en est-il de l'amélioration des bilans énergétiques et économiques lorsque la charge s'alourdit ? A refiner buys crude oils of different qualities and varying origins and he manufactures a certain number

Carburizing plasma in a low temperature austenitic stainless steel AISI 304

International Nuclear Information System (INIS)

Mota, W.T.; Ramos, F.D.; Rocha, R.C.; Barcelos, M.V.; Barcelos, M.A.

2014-01-01

The industrial use of thermochemical treatment assisted by the cold plasma has been widely employed in recent years, mainly oriented to the excellent results obtained in the surface modification of engineering materials, when compared to more traditional methods. In this work, we studied the plasma carburizing low temperature steel AISI 304 mechanical parts used in construction. The thermochemical treatment was performed at a fixed gas atmosphere 7% CH 4 (g) and 93 % H 2 (g), 350 ° C and times of 1, 3 and 5 hours. Samples being tested for Vickers hardness, abrasive microwear, microstructure evaluation by optical microscopy and SEM and X-ray diffraction. The results show significant improvement in surface hardness, wear resistance and good formation of expanded austenite layer and no identifiers peaks of carbides. The results achieved are due to diffusion/adsorption of carbon present in the gaseous atmosphere to the evaluated samples. (author)

Possibility of surface carburization of refractory metals of electric spark alloying

International Nuclear Information System (INIS)

Verkhoturov, A.D.; Isaeva, L.P.; Timofeeva, I.I.; Tsyban', V.A.

1981-01-01

The paper is concerned with a study in the alloying layer formation under electric spark alloying of refractory (Ti, Zr, Nb, Mo, W, Co, Fe) metals with graphite in argon and in air using the EhFI-46A installation. It is shown that in electric spark alloying with graphite there appear certain specific conditions for the alloying layer formation manifested in the cathode mass decrease during treatment. In this case an alloying layer consisting of carbides, oxides of the corresponding metals and material of the base is formed on the metal surface. The best carburization conditions in the process of electric spark alloying are realized for group 4 metals when treating them in ''soft'' regime, specific time of alloying being 1-3 min/sm 2 and for group 5 and 6 metals - in ''rigid'' regime of treatment and specific time of alloying 3-5 min/cm 2 [ru

Thermochemical Conversion of Lignin for Fuels and Chemicals: A Review Conversion thermochimique de la lignine en carburants et produits chimiques : une revue

Directory of Open Access Journals (Sweden)

Joffres B.

2013-10-01

Full Text Available Lignin is one of the biomass components potentially usable as renewable resource to produce fuels or chemicals. After separation from the lignocellulosic matrix, this macromolecule is nowadays essentially valorized by combustion in paper mills. If second generation ethanol is produced in the future from lignocellulosic biomass, some increasing reserves of lignin will be available in addition to the ones coming from the paper industry. The main thermochemical ways such as pyrolysis, solvolysis, hydrothermal conversion and hydroconversion considered for the valorization of the lignin are reviewed in this article. La lignine est une des composantes de la biomasse lignocellulosique potentiellement valorisable comme ressource renouvelable pour la production de carburants ou de produits chimiques. Après séparation de la matrice lignocellulosique, cette macromolécule est de nos jours essentiellement utilisée comme combustible dans l’industrie papetière. Outre cette filière papetière, la production d’éthanol de seconde génération à partir de la cellulose aura comme conséquence la mise à disponibilité d’encore plus grandes quantités de lignine. De nouvelles applications pourront donc être proposées pour l’utilisation de cette bio-ressource. Les différentes voies thermochimiques : pyrolyse, solvolyse, conversion hydrothermale et hydroconversion envisagées pour la valorisation de la lignine sont décrites dans cet article.

Activity relationships for aromatic crown ethers

International Nuclear Information System (INIS)

Wilson, Mark James

1998-01-01

This thesis involves an investigation of aromatic crown ethers and a study of their binding constants for alkali metals. The study was motivated by the current needs of the semiconductor industry to improve the scavenging of mobile ions from fabricated circuits. A number of aromatic crown ethers have been sulphonated in an attempt to improve their water solubility and cation binding activity. These materials have been extensively studied and their binding activity determined. In collaboration with a molecular modelling study, the effect of ionisable sulphonate groups on the macrocycles' behaviour has been investigated. The broader issue of the effect of substituents in aromatic crown ethers has also been studied with the preparation of a wide range of substituted crown ethers. The cation binding activity of these materials has been found to bear a simple relationship to the electron withdrawing nature of the aromatic substituents. This relationship can be accurately monitored using electronic charge densities from molecular modelling and this rational has been applied to the study of proton ionisable and lariating crown ethers. The incorporation of crown ethers into polyamic acid and polyimide frameworks has also been investigated, where the resulting materials have been found to exhibit unusual cation binding and uptake properties. These results imply that the combination of the crown ethers' macrocycle and adjacent carboxylic acid residues, from the polyamic acids, are conducive to effective cationic binding. NMR measurements, in conjunction with molecular modelling, have been used to explore the geometry changes encountered as the crown ether goes from it's uncomplexed to its complexed state. The energy requirement for these geometry changes has subsequently been used to examine the cation selectivity of these materials. The electronic charge changes associated with the complexation have also been investigated and correlated with the theoretical results. (author)

Biaxial deformation behaviour of poly-ether-ether-ketone

Science.gov (United States)

Turner, Josh; Menary, Gary; Martin, Peter

2018-05-01

The biaxial tensile properties of thin poly-ether-ether-ketone (PEEK) films are presented. Investigation into the biaxial mechanical behaviour of PEEK films will provide a preliminary insight into the anticipated stress/strain response, and potential suitability, to the possible fabrication of thin walled parts through stretch blow moulding and thermoforming processes - with the multi-axial state of strain imposed onto the heated thermoplastic sheet representative of the expected strain history experienced during these material forming processes. Following identification of the prospective forming temperature window, the biaxial mechanical behaviour of the material is characterized under differing modes of deformation, at a nominal strain rate of 1 s-1. The temperature dependence is outlined within - with an appreciable increase in flow behaviour correlated with specimen temperature exceeding its glass transition temperature (Tg).

Novel crosslinked membranes based on sulfonated poly(ether ether ketone) for direct methanol fuel cells.

Science.gov (United States)

Zhu, Yuanqin; Zieren, Shelley; Manthiram, Arumugam

2011-07-14

Novel covalently crosslinked membranes based on sulfonated poly(ether ether ketone) and carboxylated polysulfone exhibit much lower methanol crossover and better performance in direct methanol fuel cells at 65 °C in 1 and 2 M methanol solutions compared to Nafion 115 membranes.

Preparation and Characterization of Sulfonated Poly (ether ether ...

African Journals Online (AJOL)

NJD

2007-08-10

Aug 10, 2007 ... Preparation and Characterization of Sulfonated Poly (ether ... Currently perfluori- ... with phosphoric acid solution according to the method described earlier.11,12 ... where A is the membrane area available for diffusion; CA is.

Lithiated and sulphonated poly(ether ether ketone) solid state electrolyte films for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Chiu, K.-F.; Su, S.-H., E-mail: minimono42@gmail.com

2013-10-01

Poly(ether ether ketone) (PEEK) films have been synthesised and used as solid-state electrolytes for supercapacitors. In order to increase their ion conductivity, the PEEK films were sulphonated by sulphuric acid, and various amounts of LiClO{sub 4} were added. The solid-state electrolyte films were characterised by Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. The ionic conductivities of the electrolyte films were analysed by performing electrochemical impedance spectroscopy. The obtained electrolyte films can be sandwiched or directly coated on activated carbon electrodes to form solid-state supercapacitors. The electrochemical characteristics of these supercapacitors were investigated by performing cyclic voltammetry and charge–discharge tests. Under an optimal content of LiClO{sub 4}, the supercapacitor can provide a capacitance as high as 190 F/g. After 1000 cycles, the supercapacitors show almost no capacitance fading, indicating high stability of the solid-state electrolyte films. - Highlights: • Poly(ether ether ketone) (PEEK) films have been used as solid-state electrolytes. • LiClO4 addition can efficiently improve the ionic conductivity. • Supercapacitors using PEEK electrolyte films deliver high capacitance.

Lithiated and sulphonated poly(ether ether ketone) solid state electrolyte films for supercapacitors

International Nuclear Information System (INIS)

Chiu, K.-F.; Su, S.-H.

2013-01-01

Poly(ether ether ketone) (PEEK) films have been synthesised and used as solid-state electrolytes for supercapacitors. In order to increase their ion conductivity, the PEEK films were sulphonated by sulphuric acid, and various amounts of LiClO 4 were added. The solid-state electrolyte films were characterised by Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. The ionic conductivities of the electrolyte films were analysed by performing electrochemical impedance spectroscopy. The obtained electrolyte films can be sandwiched or directly coated on activated carbon electrodes to form solid-state supercapacitors. The electrochemical characteristics of these supercapacitors were investigated by performing cyclic voltammetry and charge–discharge tests. Under an optimal content of LiClO 4 , the supercapacitor can provide a capacitance as high as 190 F/g. After 1000 cycles, the supercapacitors show almost no capacitance fading, indicating high stability of the solid-state electrolyte films. - Highlights: • Poly(ether ether ketone) (PEEK) films have been used as solid-state electrolytes. • LiClO4 addition can efficiently improve the ionic conductivity. • Supercapacitors using PEEK electrolyte films deliver high capacitance

Hardness and wear properties of boron-implanted poly(ether-ether-ketone) and poly-ether-imide

International Nuclear Information System (INIS)

Lee Youngchul; Lee, E.H.; Mansur, L.K.

1992-01-01

The effects of boron beam irradiation on the hardness, friction, and wear of polymer surfaces were investigated. Typical high-performance thermoplastics, poly(ether-ether-ketone) (PEEK) and a poly-ether-imide (Ultem) were studied after 200 keV boron ion beam treatment at ambient temperature to doses of 2.3x10 14 , 6.8x10 14 , and 2.2x10 15 ions cm -2 . The hardnesses of pristine and boron-implanted materials were characterized by a conventional Knoop method and a load-depth sensing nanoindentation technique. Both measurements showed a significant increase in hardness with increasing dose. The increase in hardness was also found to depend on the penetration depth of the diamond indenter. Wear and friction properties were characterized by a reciprocating sliding friction tester with an SAE 52100 high-carbon, chrome steel ball at 0.5 and 1 N normal loads. Wear and frictional properties varied in a complex fashion with polymer type and dose, but not much with normal load. A substantial reduction in friction coefficient was observed for PEEK at the highest dose but no reduction was observed for Ultem. The wear damage was substantially reduced at the highest dose for both Ultem and PEEK. For the system studied, the highest dose, 2.2x10 15 ions cm -2 , appears to be optimum in improving wear resistance for both PEEK and Ultem. (orig.)

Optical anisotropy, molecular orientations, and internal stresses in thin sulfonated poly(ether ether ketone) films

NARCIS (Netherlands)

Koziara, B.T.; Nijmeijer, K.; Benes, N.E.

2015-01-01

The thickness, the refractive index, and the optical anisotropy of thin sulfonated poly(ether ether ketone) films, prepared by spin-coating or solvent deposition, have been investigated with spectroscopic ellipsometry. For not too high polymer concentrations (≤5 wt%) and not too low spin speeds

Optical anisotropy, molecular orientations, and internal stresses in thin sulfonated poly(ether ether ketone) films

NARCIS (Netherlands)

Koziara, Beata; Nijmeijer, Dorothea C.; Benes, Nieck Edwin

2015-01-01

The thickness, the refractive index, and the optical anisotropy of thin sulfonated poly(ether ether ketone) films, prepared by spin-coating or solvent deposition, have been investigated with spectroscopic ellipsometry. For not too high polymer concentrations (B5 wt%) and not too low spin speeds

Poly(vinylbenzyl sulfonic acid)-grafted poly(ether ether ketone) membranes

Energy Technology Data Exchange (ETDEWEB)

Hwang, Mi-Lim; Choi, Jisun; Woo, Hyun-Su; Kumar, Vinod; Sohn, Joon-Yong; Shin, Junhwa, E-mail: shinj@kaeri.re.kr

2014-02-15

Highlights: • PEEK-g-PVBSA, a polymer electrolyte membrane was prepared by a radiation grafting technique. • Poly(ether ether ketone) (PEEK), an aromatic hydrocarbon polymer was used as a grafting backbone film. • The water uptake, proton conductivity, and methanol permeability of the membranes were evaluated. • PEEK-g-PVBSA membranes show considerably lower methanol permeability compared to a Nafion membrane. -- Abstract: In this study, an aromatic hydrocarbon based polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)-grafted poly(ether ether ketone) (PEEK-g-PVBSA), has been prepared by the simultaneous irradiation grafting of vinylbenzyl chloride (VBC) monomer onto a PEEK film and subsequent sulfonation. Each chemical conversion was monitored by FT-IR and SEM–EDX instruments. The physicochemical properties including IEC, water uptake, proton conductivity, and methanol permeability of the prepared membranes were also investigated and found that the values of these properties increase with the increase of degree of grafting. It was observed that the IEC values of the prepared PEEK-g-PVBSA membranes with 32%, 58%, and 80% DOG values were 0.50, 1.05, and 1.22 meq/g while the water uptakes were 14%, 20%, and 21%, respectively. The proton conductivities (0.0272–0.0721 S/cm at 70 °C) were found to be somewhat lower than Nafion 212 (0.126 S/cm at 70 °C) at a relative humidity of 90%. However, the prepared membranes showed a considerably lower methanol permeability (0.61–1.92 × 10{sup −7} cm{sup 2}/s) compared to a Nafion 212 membrane (5.37 × 10{sup −7} cm{sup 2}/s)

Thermal stability of sulfonated Poly(Ether Ether Ketone) films : on the role of Protodesulfonation

NARCIS (Netherlands)

Koziara, B.T.; Kappert, E.J.; Ogieglo, W.; Nijmeijer, Kitty; Hempenius, M.A.; Benes, N.E.

Thin film and bulk, sulfonated poly(ether ether ketone) (SPEEK) have been subjected to a thermal treatment at 160–250 °C for up to 15 h. Exposing the films to 160 °C already causes partial desulfonation, and heating to temperatures exceeding 200 °C results in increased conjugation in the material,

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel Cementação sob plasma à baixa temperatura do aço inoxidável austenítico AISI 316L e do aço inoxidável duplex AISI F51

OpenAIRE

Carlos Eduardo Pinedo; André Paulo Tschiptschin

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% c...

Initiatives de reddition de comptes ascendante et acquisitions ...

International Development Research Centre (IDRC) Digital Library (Canada)

Corey Piccioni

mentation, au carburant, à l'énergie et aux finances se sont récemment multipliées et une conséquence des plus immédi- ates et importantes est la réévaluation des terres à ... de cas et la recherche-action participative. Le projet devrait permette la production de données probantes sur la façon dont les résidents peuvent ...

The Influence of Calcium Carbonate Composition and Activated Carbon in Pack Carburizing Low Carbon Steel Process in The Review of Hardness and Micro Structure

Science.gov (United States)

Hafni; Hadi, Syafrul; Edison

2017-12-01

Carburizing is a way of hardening the surface by heating the metal (steel) above the critical temperature in an environment containing carbon. Steel at a temperature of the critical temperature of affinity to carbon. Carbon is absorbed into the metal form a solid solution of carbon-iron and the outer layer has high carbon content. When the composition of the activator and the activated charcoal is right, it will perfect the carbon atoms to diffuse into the test material to low carbon steels. Thick layer of carbon Depending on the time and temperature are used. Pack carburizing process in this study, using 1 kg of solid carbon derived from coconut shell charcoal with a variation of 20%, 10% and 5% calcium carbonate activator, burner temperature of 950 0C, holding time 4 hours. The test material is low carbon steel has 9 pieces. Each composition has three specimens. Furnace used in this study is a pack carburizing furnace which has a designed burner box with a volume of 1000 x 600 x 400 (mm3) of coal-fired. Equipped with a circulation of oxygen from the blower 2 inches and has a wall of refractory bricks. From the variation of composition CaCO3, microstructure formed on the specimen with 20% CaCO3, better diffusion of carbon into the carbon steel, it is seen by the form marten site structure after quenching, and this indicates that there has been an increase of or adding carbon to in the specimen. This led to the formation of marten site specimen into hard surfaces, where the average value of hardness at one point side (side edge) 31.7 HRC

Effect of carbon on the oxidation of zirconium; Influence du carbone sur l'oxygenation du zirconium a haute temperature

Energy Technology Data Exchange (ETDEWEB)

Chauvin, G; Boudouresques, B; Coriou, H; Hure, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

The study of specimens contaminated by different amounts of carbon shows a deleterious effect of this element in the resistance of zirconium to high temperature oxidation (700 to 900 deg. C). We drew the following results: a) the white spots or 'pimples' observed by numerous authors seem to be caused by the oxidation of precipitated carbides. We suggest a mechanism of formation and growth of these pimples; b) for a certain carbon content, the resistance to oxidation is increased by an uniform dispersion of the carbide phase and decreased, for instance, by extrusion textures. In this case, for the more marked textures, the more oriented corrosion was observed; c) by burning of the carbide phase it can result a second reaction increasing the corrosion rate; d) thin zirconium foils undergoes dimensional changes when scaling in oxygen. This unusual feature is also subordinated to carbon content and specially to the carbide phase dispersion. (author) [French] L'etude d'echantillons differemment contamines par le carbone nous a permis de mettre en evidence l'action particulierement nocive de cet element sur la resistance du zirconium a la corrosion par l'oxygene a haute temperature (700 a 900 deg. C). Nous avons pu degager les resultats essentiels suivants: a) l'origine des pustules d'oxyde blanc signalees par de nombreux auteurs doit etre recherchee dans l'oxydation des carbures precipites. Nous suggerons un mecanisme de formation et de croissance de ces pustules, b) la tenue du metal est d'autant meilleure que, pour une meme teneur en carbone, la phase 'carbure' est plus uniformement dispersee. En consequence, si la dispersion est mauvaise, on observe selon l'axe des textures de filage, par exemple, une corrosion preferentielle d'autant plus accentuee que les textures sont plus marquees, c) la combustion de la phase 'carbure' peut engendrer une reaction secondaire susceptible d'accroitre la cinetique de corrosion, d) l'expansion des grandes faces d

Preparation of nanocrystalline iron-carbon materials as fillers for polymers

International Nuclear Information System (INIS)

Narkiewicz, U; Pelech, I; Roslaniec, Z; Kwiatkowska, M; Arabczyk, W

2007-01-01

This paper presents a method of preparing nanocrystalline iron-carbon materials which can be applied as fillers for polymers. Nanocrystalline iron samples were carburized either under ethylene/hydrogen mixture or under pure ethylene. Three kinds of samples were prepared: cementite/carbon (Fe 3 C/C), iron/cementite (Fe/Fe 3 C) and iron/carbon (Fe/C) ones. After carburization the samples were characterized using XRD and SEM methods. The obtained samples of iron-carbon nanoparticles were applied as fillers to polymer nanocomposites prepared in a polycondensation reaction (in situ) in a poly(ether-ester) matrix. The nanofillers were dispersed in monomers (diols) using a sonificator and a high-speed rotary stirrer. The obtained nanocomposites were characterized as regards their structure (SEM method) and mechanical behaviour

On new physical reality (on ψ-ether)

International Nuclear Information System (INIS)

Isaev, P.S.

2002-01-01

It is shown that there exists a new physical reality - the ψ-ether. All the achievements of quantum mechanics and quantum field theory are due to the fact that both the theories include the influence of ψ-ether on the physical processes occurring in the Universe. Physics of the XX century was first of all the physics of ψ-ether

Excellent durability of DLC film on carburized steel (JIS-SCr420) under a stress of 3.0 GPa

International Nuclear Information System (INIS)

Yakabe, F; Kumagai, M; Kuwahara, H; Ochiai, S; Jinbo, Y; Horiuchi, T

2008-01-01

To improve durability of transmission gears, Diamond Like Carbon (DLC) film coated on roller was estimated as well as TiN film. These films were coated on JIS-SCr420 steel, which was carburized, quenched, and tempered. DLC and TiN films were deposited by PCVD and PVD process, respectively. These surface modified rollers were estimated by usual metallurgical methods (observation of microstructure by optical microscope, SEM, and TEM, measurement of hardness by Vickers hardness tester and nano-indentator), measurement of friction coefficient by ball-on-disk in dry atmosphere, analysis of carbon by Raman spectroscopy and hydrogen by EDRA, and lifetime of pitting by the roller-pitting test. The hardness values were 21 GPa and 26 GPa, the elasticity coefficients were 192 GPa and 336 GPa, the friction coefficients were 0.1∼0.15 and 0.5∼0.6 for DLC and TiN films, respectively. The present DLC was a typical DLC called as hydrogenated amorphous carbon (a-C: H). The hydrogen content was about 20%. The surface fatigue resistance of DLC-coated specimen had 100 times longer life than that the carburized and quenched one even under Hertzian contact stress of 3.0 GPa. TiN coated specimen was failed at 3.0 GPa by 5.17·10 5 cycles despite that the strength of the surface of the substrate was reduced due to the exposure at higher temperature in the coating process than the temperature for tempering

Production of Methanol-Higher Alcohol Mixtures from Natural Gas via Syngas Chemistry Production de mélanges méthanol-alcools supérieurs à partir du gaz, via (CO + H2

Directory of Open Access Journals (Sweden)

Courty P.

2006-11-01

Full Text Available Despite the prevailing position of ethers (MTBE, TAME as octane boosters, and the low oil prices at present, alcohol synthesis remains one of the near future means of natural gas upgrading via syngas chemistry. After a review of the available process development data in the field, this paper focuses on the IFP process studies, based on the CuCo and CuNi catalysts developed by Institut Français du Pétrole (IFR, France and Idemitsu Kosan (Japan. The adequacy between the product specifications, and the optimization of the performances is then discussed in a technico-economic context, together with a presentation of lab scale, pilot scale and demonstration scale test results. As a conclusion, a prospective overall view brings together todays economics and some improvement guidelines dealing with investments, operating cost and catalyst performances. Cette publication présente les travaux de R & D (Recherche et Développement menés par l'Institut Français du Pétrole (IFP, France et Idemitsu Kosan (Japon en synthèse d'alcools. Elle situe les résultats dans le contexte technique et économique actuel. L'accroissement constant des ressources prouvées en gaz et, chronologiquement, les deux crises pétrolières, la suppression du plomb dans les essences, ont conduit le monde industriel à intensifier les recherches concernant la synthèse d'alcools. Très récemment, les effets bénéfiques de l'addition d'alcools sur les émissions de polluants ont été mis en évidence. Toutefois, l'additivation de carburants par les alcools est en voie de disparition au profit des éthers, alors que, indépendamment, les procédés de production d'ammoniac, de méthanol, d'acide acétique, également fondés sur le gaz, se sont seuls développés. La synthèse d'alcools a fait l'objet de nombreux travaux, résumés dans les tableaux 1 et 2. L'étude des différents aspects réactionnels amène à prendre en compte l'exothermicité importante des r

Synthesis Gas Purification Purification des gaz de synthèse

Directory of Open Access Journals (Sweden)

Chiche D.

2013-10-01

Full Text Available Fischer-Tropsch (FT based B-XTL processes are attractive alternatives for future energy production. These processes aim at converting lignocellulosic biomass possibly in co-processing with petcoke, coal, or vacuum residues into synthetic biofuels. A gasification step converts the feed into a synthesis gas (CO and H2 mixture , which undergoes the Fischer-Tropsch reaction after H2/CO ratio adjustment and CO2 removal. However synthesis gas also contains various impurities that must be removed in order to prevent Fischer-Tropsch catalyst poisoning. Due to the large feedstocks variety that can be processed, significant variations of the composition of the synthesis gas are expected. Especially, this affects the nature of the impurities that are present (element, speciation, as well as their relative contents. Moreover, due to high FT catalyst sensitivity, severe syngas specifications regarding its purity are required. For these reasons, synthesis gas purification constitutes a major challenge for the development of B-XTL processes. In this article, we focus on these major hurdles that have to be overcome. The different kinds of syngas impurities are presented. The influence of the nature of feedstocks, gasification technology and operating conditions on the type and content of impurities is discussed. Highlight is given on the fate of sulfur compounds, nitrogen compounds, halides, transition and heavy metals. Main synthesis gas purification technologies (based on adsorption, absorption, catalytic reactions, etc. are finally described, as well as the related challenges. Les procédés de synthèse de biocarburants par voie Fischer-Tropsch (FT, voies B-XTL, représentent des alternatives prometteuses pour la production d’énergie. Ces procédés permettent la conversion en carburants de synthèse de biomasse lignocellulosique, éventuellement mise en oeuvre en mélange avec des charges fossiles telles que petcoke, charbons ou résidus sous vide. Pour

Sulfonated poly(ether ether ketone) membranes for electric double layer capacitors

International Nuclear Information System (INIS)

Kim, Wan Ju; Kim, Dong-Won

2008-01-01

Sulfonated poly(ether ether ketone) (S-PEEK) with different degree of sulfonation (DS) has been prepared and evaluated as a proton conducting membrane for electric double layer capacitor (EDLC). The polymer electrolytes prepared with S-PEEK membrane exhibited ionic conductivities about 1.2 x 10 -3 -4.5 x 10 -3 S cm -1 at room temperature, which depended on both soaking solvent and degree of sulfonation. The quasi-solid-state EDLCs consisted of activated carbon electrodes and S-PEEK membrane were assembled, and their electrochemical characteristics were studied by cyclic voltammetry and charge-discharge cycle tests. The effect of DS on the electrochemical performances of EDLCs has been investigated

Promoting environmentally sound management of polybrominated diphenyl ethers in Asia.

Science.gov (United States)

Li, Jinhui; Zhao, Nana; Liu, Xue; Wu, Xiaoyang

2014-06-01

Polybrominated diphenyl ethers with persistent organic pollutant properties are required to be controlled by the Stockholm Convention. Recently, polybrominated diphenyl ether contamination has become widespread in Asia, mainly because of the disposal and recycling processes of polybrominated diphenyl ether-containing wastes. The management status, production, usage, import/export, treatment, and disposal, as well as implementation deficiencies for the environmentally sound management of polybrominated diphenyl ethers and polybrominated diphenyl ether-containing materials in ten Asian countries were investigated and assessed in this study. This information could help the participating countries implement the Stockholm Convention and could promote the regional environmentally sound management of polybrominated diphenyl ether-containing articles and products. The results obtained were as follows. (1) Most of the countries studied lacked environmental policies and regulations, or even standards of polybrominated diphenyl ether pollution management and emission control actions. Accurate data on the consumption and importation of polybrominated diphenyl ether-containing materials, however, were not available for all the participating countries. In addition, there were no special treatment or disposal systems for polybrominated diphenyl ether-containing materials, or emission-cutting measures for the treatment of waste in these countries, owing to the lack of sufficient funding or technologies. (2) The improper dismantling of e-waste is a major source of polybrominated diphenyl ether emissions in these countries. (3) Proper e-waste management could result in a breakthrough in the environmentally sound management of this major polybrominated diphenyl ether-containing material flow, and could significantly reduce polybrominated diphenyl ether emissions. Finally, based on the study results, this article puts forward some recommendations for improving the environmentally

Chemoselective Deprotection of Triethylsilyl Ethers

Science.gov (United States)

Chandra, Tilak; Broderick, William E.; Broderick, Joan B.

2009-01-01

An efficient and selective method was developed for the deprotection of triethylsilyl (TES) ethers using formic acid in methanol (5–10%) or in methylene chloride 2–5%) with excellent yields. TES ethers are selectively deprotected to the corresponding alcohols in high yields using formic acid in methanol under mild reaction conditions. Other hydroxyl protecting groups like t-butyldimethylsilyl (TBDMS) remain unaffected. PMID:20183570

Potentiel des moteurs à mélange pauvre face aux moteurs actuels à réglage stoechiométrique : consommation, émissions, exigence en octane The Challenge to Modern Stoichiometric Engines by the Potential Lean-Burn Engine: Consumption, Emissions, Fuel Requirements

Directory of Open Access Journals (Sweden)

Douaud A. M.

2006-11-01

Full Text Available Le moteur à allumage commandé pour application automobile aux États-Unis est généralement dépollué par catalyse trifonctionnelle qui impose un contrôle stoechiométrique du mélange air-carburant. Le contexte européen de 1990 pour la qualité de l'air stimule l'industrie automobile dans ses recherches de solutions techniques performantes. Le moteur à mélange pauvre, performant en consommation, est une solution potentielle si l'émission de NOx peut être maîtrisée par la combustion. Cet objectif nécessite une conception du moteur contrôlant la turbulence et l'hétérogénéité du mélange air + carburant + résiduels pendant la combustion. La longévité de l'adaptation optimale moteur-carburant nécessitera un contrôle électronique de l'allumage et l'utilisation d'additifs détergents. Pour satisfaire les réglementations les plus sévères, les émissions de CO et HC pourront être contrôlées par un simple pot catalytique d'oxydation. Des oxydes de métaux non précieux introduits dans la formule catalytique en addition aux métaux précieux maintiennent la fonction oxydante pendant les transitoires en mélange riche tout en réduisant partiellement les NOx. Une vue d'ensemble de ce concept basé sur des simulations numériques et des résultats expérimentaux de consommation, d'émission, d'exigence en octane, etc. est présentée. Spark-ignition engines for automotive applications in the United States are currently depolluted by a 3-way catalyst that requires air-fuel control at stoichiometry. The 1990 European context for air pollution control is stimulating the automotive industry to search for improved technical solutions. The lean-burn engine is a potential fuel-efficient answer if its combustion can be optimized for low NOx emissions. Achieving this challenging approach requires engine design to control the turbulence and heterogeneity of the air + fuel + residual mixture during combustion. Electronic ignition

[Early contributions from Erlangen to the theory and practice of ether and chloroform anesthesia. 1. Heyfelder's clinical trial with ether and chloroform].

Science.gov (United States)

Hintzenstern, U v; Schwarz, W

1996-02-01

The era of modern anaesthesia in Germany began on January 24th, 1847. This day, professor in ordinary Johann Ferdinand Heyfelder anaesthetized a patient with sulphuric ether in the clinic of surgery and ophthalmology of the University of Erlangen. By March 17th, 1847, Heyfelder had performed 121 surgical procedures under ether. The operations in majority were teeth-extractions, and a few more complex operations such as the treatment of a harelip or of lip cancer or the resection of the shoulder joint. Heyfelder described in detail 108 of these inhalations in a little book entitled The experiments with sulphuric ether. This monograph published in March, 1847, represents one of the first complete dissertations on sulphuric ether in the German literature. In a special chapter he analyzed the development of various physiological and psychological parameters during etherization. Heyfelder also examined blood and urine of some etherized patients and reported that he did not find any important or specific alterations. In 1847, Heyfelder was probably the first to apply salt-ether in man. After 4 administrations he concluded that salt ether acted more quickly but shorter than sulphuric ether. Advantageous were its application without problems and ease of induction. Disadvantageous were its high volatility, its price and the difficulty of getting it in a pure form. From December, 1847, on Heyfelder started to use chloroform. He was now able to perform more major operations, for example, the total resection of the hip-joint. In his book The experiments with sulphuric ether, salt ether, and chloroform he describes a great number of anaesthetic administrations using these 3 agents. In his summary Heyfelder concluded, that chloroform was undoubtly superior to sulphuric ether mainly because it was a quicker acting and longer lasting agent and leads to deeper narcosis. Moreover its application was much easier for it needed no special apparatus. However, because of its great

Molecular structure impacts on secondary organic aerosol formation from glycol ethers

Science.gov (United States)

Li, Lijie; Cocker, David R.

2018-05-01

Glycol ethers, a class of widely used solvents in consumer products, are often considered exempt as volatile organic compounds based on their vapor pressure or boiling points by regulatory agencies. However, recent studies found that glycol ethers volatilize at ambient conditions nearly as rapidly as the traditional high-volatility solvents indicating the potential of glycol ethers to form secondary organic aerosol (SOA). This is the first work on SOA formation from glycol ethers. The impact of molecular structure, specifically -OH, on SOA formation from glycol ethers and related ethers are investigated in the work. Ethers with and without -OH, with methyl group hindrance on -OH and with -OH at different location are studied in the presence of NOX and under "NOX free" conditions. Photooxidation experiments under different oxidation conditions confirm that the processing of ethers is a combination of carbonyl formation, cyclization and fragmentation. Bulk SOA chemical composition analysis and oxidation products identified in both gas and particle phase suggests that the presence and location of -OH in the carbon bond of ethers determine the occurrence of cyclization mechanism during ether oxidation. The cyclization is proposed as a critical SOA formation mechanism to prevent the formation of volatile compounds from fragmentation during the oxidation of ethers. Glycol ethers with -CH2-O-CH2CH2OH structure is found to readily form cyclization products, especially with the presence of NOx, which is more relevant to urban atmospheric conditions than without NOx. Glycol ethers are evaluated as dominating SOA precursors among all ethers studied. It is estimated that the contribution of glycol ethers to anthropogenic SOA is roughly 1% of the current organic aerosol from mobile sources. The contribution of glycol ethers to anthropogenic SOA is roughly 1% of the current organic aerosol from mobile sources and will play a more important role in future anthropogenic SOA

Palladium-Catalyzed Reductive Insertion of Alcohols into Aryl Ether Bonds

Energy Technology Data Exchange (ETDEWEB)

Wang, Meng [Institute for Integrated Catalysis, Pacific Northwest National Laboratory, P.O. Box 999 Richland WA 99352 USA; Gutiérrez, Oliver Y. [Institute for Integrated Catalysis, Pacific Northwest National Laboratory, P.O. Box 999 Richland WA 99352 USA; Camaioni, Donald M. [Institute for Integrated Catalysis, Pacific Northwest National Laboratory, P.O. Box 999 Richland WA 99352 USA; Lercher, Johannes A. [Institute for Integrated Catalysis, Pacific Northwest National Laboratory, P.O. Box 999 Richland WA 99352 USA; Department of Chemistry and Catalysis Research Institute, TU München, Lichtenbergstrasse 4 85748 Garching Germany

2018-03-06

Pd/C catalyzes C-O bond cleavage of aryl ethers (diphenyl ether and cyclohexyl phenyl ether) by methanol in H2. The aromatic C-O bond is cleaved by reductive methanolysis, which is initiated by Pd-catalyzed partial hydrogenation of one phenyl ring to form an enol ether. The enol ether reacts rapidly with methanol to form a ketal, which generates methoxycyclohexene by eliminating phenol or an alkanol. Subsequent hydrogenation leads to methoxycyclohexane.

Modified nanocrystal cellulose/fluorene-containing sulfonated poly(ether ether ketone ketone) composites for proton exchange membranes

Science.gov (United States)

Wei, Yingcong; Shang, Yabei; Ni, Chuangjiang; Zhang, Hanyu; Li, Xiaobai; Liu, Baijun; Men, Yongfeng; Zhang, Mingyao; Hu, Wei

2017-09-01

Highly sulfonated poly(ether ether ketone ketone)s (SFPEEKKs) with sulfonation degrees of 2.34 (SFPEEKK5) and 2.48 (SFPEEKK10) were synthesized through the direct sulfonation of a fluorene-containing poly(ether ether ketone ketone) under a relatively mild reaction condition. Using the solution blending method, sulfonated nanocrystal cellulose (sNCC)-enhanced SFPEEKK composites (SFPEEKK/sNCC) were successfully prepared for investigation as proton exchange membranes. Transmission electron microscopy showed that sNCC was uniformly distributed in the composite membranes. The properties of the composite membranes, including thermal stability, mechanical properties, water uptake, swelling ratio, oxidative stability and proton conductivity were thoroughly evaluated. Results indicated that the insertion of sNCC could contribute to water management and improve the mechanical performance of the membranes. Notably, the proton conductivity of SFPEEKK5/sNCC-5 was as high as 0.242 S cm-1 at 80 °C. All data proved the potential of SFPEEKK/sNCC composites for proton exchange membranes in medium-temperature fuel cells.

Low leaded motor gasoline of high knock rating having few pollution effects

Energy Technology Data Exchange (ETDEWEB)

Droste, W; Obenaus, F; Schoefer, W

1975-11-13

A carburator gasoline has been developed that has a high knock rating and few enviromental pollution effects. The gasoline contains 0.1 to 0.4 g of lead per liter, and up to 20 percent by volume of a mixture made up of 80 to 90 percent by weight methyl-tert.-butyl ether and 20 to 10 percent by weight methanol. Through tests it has been determined that the characteristics (particularly the octane number) of a gasoline having a lead content of 0.15 g/liter and one of the above mentioned additives are better than those of a gasoline with a lead content of 0.4 g/liter, but not containing an additive. The harmful emissions were also lower. In addition, the danger of carburator icing is decreased.

Microwave sintering of poly-ether-ether-ketone (PEEK) based coatings deposited on metallic substrate

International Nuclear Information System (INIS)

Zhang, G.; Leparoux, S.; Liao, H.; Coddet, C.

2006-01-01

In this paper, the feasibility of microwave (MW) sintering PEEK (poly-ether-ether-ketone) based coatings was investigated. Three coatings were studied: pure PEEK, micron-SiC and nano-SiC particles filled (wt.10%) PEEK coatings. The results indicate that, for the two composite coatings, the SiC particles distributed in the polymer matrix, as a good MW susceptor, could be heated preferentially by MW radiation. Consequently, the polymer matrix was heated by these particles

Actinide/crown ether chemistry

International Nuclear Information System (INIS)

Benning, M.M.

1988-01-01

A structural survey of actinide/crown ether compounds was conducted in order to investigate the solid state chemistry of these complexes. Several parameters - the metal size, crown type, counterion, solvent systems and reaction and crystallization conditions - were varied to correlate their importance in complexation. Under atmospheric conditions, two types of complexes were isolated, those containing only hydrogen-bonded crown interactions and instances where the crown interacts directly with the metal center. In both cases, water seems to play a very important role. When coordinated to the metal, water molecules exhibit the necessary donor properties required for the formation of hydrogen-bonded contacts. The water molecules also provide fierce competition with the crown ethers for metal-binding sites and in most cases prohibit the formation of complexes in which direct metal-ligand association exists. The results of this study indicate that direct interaction between the metal atoms and the crown ethers, in the presence of water, can only occur with polyether conformations which limit the steric replusions within the metal coordination sphere

Rearrangements of Cycloalkenyl Aryl Ethers

Directory of Open Access Journals (Sweden)

Mercedesz Törincsi

2016-04-01

Full Text Available Rearrangement reactions of cycloalkenyl phenol and naphthyl ethers and the acid-catalyzed cyclization of the resulting product were investigated. Claisen rearrangement afforded 2-substituted phenol and naphthol derivatives. Combined Claisen and Cope rearrangement resulted in the formation of 4-substituted phenol and naphthol derivatives. In the case of cycloocthylphenyl ether the consecutive Claisen and Cope rearrangements were followed by an alkyl migration. The mechanism of this novel rearrangement reaction is also discussed.

Ether: Bitcoin's competitor or ally?

OpenAIRE

Bouoiyour, Jamal; Selmi, Refk

2017-01-01

Although Bitcoin has long been dominant in the crypto scene, it is certainly not alone. Ether is another cryptocurrency related project that has attracted an intensive attention because of its additional features. This study seeks to test whether these cryptocurrencies differ in terms of their volatile and speculative behaviors, hedge, safe haven and risk diversification properties. Using different econometric techniques, we show that a) Bitcoin and Ether are volatile and relatively more resp...

Catalytic hydroprocessing of lignin β-O-4 ether bond model compound phenethyl phenyl ether over ruthenium catalysts

NARCIS (Netherlands)

Gomez-Monedero, B.; Faria, J.; Bimbela, F.; Ruiz, M.P.

2017-01-01

The catalytic hydroprocessing of phenethyl phenyl ether (PPE), a model compound of one of the most significant ether linkages within lignin structure, β-O-4, has been studied. Reactions were carried out using two ruthenium-based catalysts, supported on different materials: 3.8 wt.% Ru/C and 3.9 wt.%

Metallographical procedure for detecting carburized layer in the 12Kh18N10T steel tubes

International Nuclear Information System (INIS)

Najmark, S.I.; Shmalenyuk, R.P.

1977-01-01

The various causes of the tendency to intercrystalline corrosion of stainless steel tubing were studied. 12Kh18N10T steel tube specimens were metallographically investigated to reveal the presence and depth of the carburized layer. Unlubricated specimens and specimens with the graphite-saltpeter lubrication applied on them were austenized in the temperature range from 950 to 1250 deg C and then exposed to a provoking anneal at 650 deg C for 24 h. All the lubricated specimens showed a carbide network along grain boundaries and intercrystalline cracks. The specimens treated without lubrication had no cracks. The method offered can differentiate poor tube cleaning and the undesirable effect of other processing steps on the tubes

Radiolabeled cholesteryl ethers: A need to analyze for biological stability before use

Directory of Open Access Journals (Sweden)

Denny Joseph Manual Kollareth

2018-03-01

Full Text Available Radiolabeled cholesteryl ethers are widely used as non-metabolizable tracers for lipoproteins and lipid emulsions in a variety of in vitro and in vivo experiments. Since cholesteryl ethers do not leave cells after uptake and are not hydrolyzed by mammalian cellular enzymes, these compounds can act as markers for cumulative cell uptakes of labeled particles. We have employed [3H]cholesteryl oleoyl ether to study the uptake and distribution of triglyceride-rich emulsion particles on animal models. However, questionable unexpected results compelled us to analyze the stability of these ethers. We tested the stability of two commercially available radiolabeled cholesteryl ethers - [3H]cholesteryl oleoyl ether and [3H]cholesteryl hexadecyl ether from different suppliers, employing in vitro, in vivo and chemical model systems. Our results show that, among the two cholesteryl ethers tested, one ether was hydrolyzed to free cholesterol in vitro, in vivo and chemically under alkaline hydrolyzing agent. Free cholesterol, unlike cholesteryl ether, can then re-enter the circulation leading to confounding results. The other ether was not hydrolyzed to free cholesterol and remained as a stable ether. Hence, radiolabeled cholesteryl ethers should be analyzed for biological stability before utilizing them for in vitro or in vivo experiments. Keywords: Cholesteryl ether, J774 A2 macrophages, Soy oil emulsion, Thin layer chromatography, triDHA emulsion

Perspectives d'amélioration du rendement à très faible charge des moteurs d'automobile Prospects for Lmprovinq the Very-Low-Load Efficiency of Automotive Engines

Directory of Open Access Journals (Sweden)

Douaud A.

2006-11-01

Full Text Available Le mauvais rendement énergétique des véhicules utilisés à très faible charge (circulation urbaine, vitesses limitées provient entre autres des combustions non optimales. Celles-ci sont de plusieurs types : combustion lente et/ou tardive, ratés de propagation. L'acquisition de cycles de pression au moyen du système DIGITAP développé à l'In-titut Français du Pétrole (IFP est décrite et le calcul instantané du travail cycle-à-cycle permet de définir un critère de stabilité de fonctionnement du moteur. L'analyse thermodynamique des cycles montre que la composition du mélange air + carburant + gaz résiduels, trop proche des limites de propagabilité de flamme, est à l'origine des phénomènes observés. Des voies d'action portant sur les gaz résiduels, la turbulence et les paramètres du système d'allumage sont dégagées et permettent des améliorations importantes du rendement. The poor energy efficiency of vehicles used at very low engine load (urban traffic, limited speeds comes from non-optimum combustion, among other causes. Such combustion may be of several types, i. e. slow and/or late combustion, propagation misfiring. The recording of pressure cycles by the DIGITAP system developed at Institut Français du Pétrole (IFP is described, and the instantaneous computing of the cycle-to-cycle work enables a stability criterion for engine operating to be described. The thermodynamic analysis of the cycles shows that the composition of the air + fuel + residuel gas mixture which is too close to flame propagation limits is at the origin of the phenomena observed. Methods of action concerning residual gases, turbulence and the parameters of the ignition system are determined and make for great improvements in efficiency and stability for such types of running.

Radiolabeled cholesteryl ethers: A need to analyze for biological stability before use.

Science.gov (United States)

Manual Kollareth, Denny Joseph; Chang, Chuchun L; Hansen, Inge H; Deckelbaum, Richard J

2018-03-01

Radiolabeled cholesteryl ethers are widely used as non-metabolizable tracers for lipoproteins and lipid emulsions in a variety of in vitro and in vivo experiments. Since cholesteryl ethers do not leave cells after uptake and are not hydrolyzed by mammalian cellular enzymes, these compounds can act as markers for cumulative cell uptakes of labeled particles. We have employed [ 3 H]cholesteryl oleoyl ether to study the uptake and distribution of triglyceride-rich emulsion particles on animal models. However, questionable unexpected results compelled us to analyze the stability of these ethers. We tested the stability of two commercially available radiolabeled cholesteryl ethers - [ 3 H]cholesteryl oleoyl ether and [ 3 H]cholesteryl hexadecyl ether from different suppliers, employing in vitro , in vivo and chemical model systems. Our results show that, among the two cholesteryl ethers tested, one ether was hydrolyzed to free cholesterol in vitro , in vivo and chemically under alkaline hydrolyzing agent. Free cholesterol, unlike cholesteryl ether, can then re-enter the circulation leading to confounding results. The other ether was not hydrolyzed to free cholesterol and remained as a stable ether. Hence, radiolabeled cholesteryl ethers should be analyzed for biological stability before utilizing them for in vitro or in vivo experiments.

Numerical investigation on the effect of injection pressure on the internal flow characteristics for diethyl ether, dimethyl ether and diesel fuel injectors using CFD

Directory of Open Access Journals (Sweden)

Vijayakumar Thulasi

2011-01-01

Full Text Available The spray characteristics of the diesel fuel are greatly affected by the cavitation formed inside the injector due to the high pressure differential across the nozzle. Many researchers across the globe are exploring the potential of using diethyl ether and dimethyl ether as an alternate for diesel fuel to meet the strict emission norms. Due to the variation in the fuel properties the internal flow characteristics in injectors for ether fuels are expected to be different from that of the diesel fuel. In this paper computational technique is used to study and compare the internal flow characteristics of diethyl ether, dimethyl ether and diesel fuel. The two phase flow model considering the fuel as a mixture of liquid and vapor is adopted for the simulation study. The injection pressure is varied from 100 to 400 bar and the flow characteristics of all three fuels are simulated and compared. Results indicate that all three fuels have distinct cavitating patterns owing to different property values. The dimethyl ether is found to be more cavitating than diesel and diethyl ether fuels as expected. The mass of fuel injected are found to be decreasing for the ether fuels when compared with diesel fuel at all injection pressures.

Researches on vanadium and its compounds; Recherches sur le Vanadium et ses composes

Energy Technology Data Exchange (ETDEWEB)

Morette, Andre

1937-06-03

In this research thesis, the author proposes a new study of the action of some reduction agents on two groups of vanadium compounds, oxides and chlorides. Thus, he reports the study of the circumstances of reduction of vanadium oxides by carbon and of vanadium carburization from these compounds. He also reports the determination of the composition of vanadium melts obtained at high temperatures (either in a vacuum furnace or with an electric arc furnace). In order to determine in which conditions the processing of vanadium oxides could produce the pure metal, the author studied the action of calcium and magnesium on the vanadium pentoxide and trioxide. The second part of the thesis addresses the preparation of pure vanadium from vanadium anhydride chlorides. Then, the author reports the development of processes which could easily produce powdered vanadium [French] Nous nous sommes propose de reprendre l'etude de l'action de quelques reducteurs sur les deux groupes de composes du vanadium, oxydes et chlorures. Nous avons ete ainsi amene a preciser les circonstances de la reduction des oxydes de vanadium par le carbone et de la carburation du vanadium a partir de ceux-ci, puis a determiner la constitution des fontes de vanadium obtenues a haute temperature, soit au four a vide, soit au four a arc. D'autre part, en vue de determiner dans quelles conditions le traitement des oxydes de vanadium pourrait conduire au metal pur, nous avons repris et complete des travaux anterieurs concernant l'action du calcium et du magnesium sur le pentoxyde ou eventuellement le trioxyde de vanadium. Une seconde partie de notre these a ete consacree a la preparation du vanadium pur a partir des chlorures anhydres de vanadium. Nous nous sommes attache a trouver le mode operatoire le plus favorable pour l'obtention de chacun d'eux. Il nous a ete donne ainsi l'occasion de preciser certaines de leurs proprietes physiques et chimiques. Puis, a la suite d'essais systematiques, nous avons

AIRBORNE POLYBROMINATED DIPHENYL ETHERS IN A COMPUTER CLASSROOM OF COLLEGE IN TAIWAN

Directory of Open Access Journals (Sweden)

F. H. Chang ، C. R. Yang ، C. Y. Tsai ، W. C. Lin

2009-04-01

Full Text Available This study characterized the airborne exposure of students to thirty polybrominated diphenyl ether congeners inside and outside a computer classroom in a southern Taiwan college. Arithmetic mean values of total indoor and outdoor polybrominated diphenyl ether concentrations were 125.0 pg/m3 (89.8 to 203.9 pg/m3 and 110.3 pg/m3 (83.5 to 157.0 pg/m3, respectively. Total indoor polybrominated diphenyl ether concentrations were one order of magnitude lower than those detected in homes in Birmingham, United Kingdom and in Ottawa, Canada but were several times higher than those measured in the ambient air in Ottawa, Canada and from the Bohai Sea to the Arctic. The five highest indoor concentrations of polybrominated diphenyl ether congeners were decabromodiphenyl ether (23.0 pg/m3, 4,4’-dibromodiphenyl ether (15.9 pg/m3, 2,2’,3,4,4’,5,5’,6-octabromodiphenyl ether (10.6 pg/m3, 2,4-dibromodiphenyl ether (10.3 pg/m3 and 2,2’,3,4,4’,5’,6-heptabromodiphenyl ether (10.0 pg/m3. Although indoor and outdoor total polybrominated diphenyl ether concentrations did not significantly differ, the indoor concentrations of 2,4-dibromodiphenyl ether, 2,2’,4-tribromodiphenyl ether, 2,4,4’-tribromodiphenyl ether, 2,2’,4,5’-tetrabromodiphenyl ether and 2,3’,4’,6-tetrabromodiphenyl ether were significantly higher than their outdoor concentrations. This study suggests the following measures: 1 to increase the air exchange rate and open classroom doors and windows for several minutes before classes to reduce indoor PBDE concentrations; 2 to reduce polybrominated diphenyl ether emissions from new devices, it’s better to use computer-related products that meet the Restriction of Hazardous Substances Directive adopted by the European Union.

Thermally reversible cross-linked poly(ether-urethanes

Directory of Open Access Journals (Sweden)

V. Gaina

2013-07-01

Full Text Available Cross-linked poly(ether-urethanes were prepared by Diels-Alder (DA reaction of the furan-containing poly(ether-urethane to bismaleimides and showed thermal reversibility evidenced by differential scanning calorimetry and attenuated total reflectance in conjunction with Fourier transform infrared spectroscopy (ATR-FTIR. The furan-containing poly(ether-urethanes were synthesized by the polyaddition reaction of 1,6-hexamethylene diisocyanate (HMDI or 4,4'- dibenzyl diisocyanate (DBDI to poly(tetramethylene ether glycol (PTMEG having Mn = 250, 650, 1000, 1500 and 2000 and 2-[N,N-bis(2-methyl-2-hydroxyethylamino]furfuryl as chain extender by the solution prepolymer method. The molar ratio of isocyanate: PTMEG:chain extender varied from 2:1:1 to 4:1:3, which produces a molar concentration of furyl group ranging between 3.65•10–4 and 1.25•10–3 mol/g.

Thermal Stability of Sulfonated Poly(Ether Ether Ketone) Films: on the Role of Protodesulfonation

OpenAIRE

Koziara, Beata; Kappert, Emiel; Ogieglo, Wojciech; Nijmeijer, Dorothea C.; Hempenius, Mark A.; Benes, Nieck Edwin

2016-01-01

Thin film and bulk, sulfonated poly(ether ether ketone) (SPEEK) have been subjected to a thermal treatment at 160–250 °C for up to 15 h. Exposing the films to 160 °C already causes partial desulfonation, and heating to temperatures exceeding 200 °C results in increased conjugation in the material, most likely via a slight cross-linking by H-substitution. It is well-known that the sulfonate proton plays a major role in the desulfonation reactions, and exchanging the protons with other cations ...

α-Diazo oxime ethers for N-heterocycle synthesis.

Science.gov (United States)

Choi, Subin; Ha, Sujin; Park, Cheol-Min

2017-06-01

This Feature Article introduces the preparation and synthetic utility of α-diazo oxime ethers. α-Oximino carbenes are useful synthons for N-heterocycles, and can be easily prepared from α-diazo oxime ethers as precursors. We begin with the preparation of α-diazo oxime ethers and their application in [3+2] cycloaddition. It turns out that the nature of metals bound to carbenes plays a crucial role in modulating the reactivity of α-oximino carbenes, in which copper carbenes smoothly react with enamines, whereas the less reactive enol ethers and nitriles require gold carbenes. In Section 3.2, a discussion on N-O and C-H bond activation is presented. Carbenes derived from diazo oxime ethers show unique reactivity towards N-O and C-H bond activation, in which the proximity of the two functionalities, carbene and oxime ether, dictates the preferred reaction pathways toward pyridines, pyrroles, and 2H-azirines. In Section 3.3, the development of tandem reactions based on α-diazo oxime ethers is discussed. The nature of carbenes in which whether free carbenes or metal complexes are involved dissects the pathway and forms different types of 2H-azirines. The 2H-azirine formation turned out to be an excellent platform for the tandem synthesis of N-heterocycles including pyrroles and pyridines. In the last section, we describe the electrophilic activation of 2H-azirines with vinyl carbenes and oximino carbenes. The resulting azirinium species undergo rapid ring expansion rearrangements to form pyridines and pyrazines.

Subsystem Testing and Flight Test Instrumentation.

Science.gov (United States)

1981-04-01

du isoteur avec loa autres systemes do Ilavion. L’anticipation et la r~solution do con probl~mom doivent absolument Atro r~alis~es do faqon...carburant avian. Des esosis, par temps chaud et froid , sont g~n~ralement inclus dens tout programme de d6veloppemont (Kiruna (Finlande) ot Marrakech...trim froide , ainsi quaosur des terrains on altitude pormottont ensuite de contr8ler la vaLidit6 den conaignee do d~marrage propos6es. 7 -ALINENTATION

Dimethyl ether as a drift-chamber gas

International Nuclear Information System (INIS)

Bari, G.; Basile, M.; Bonvicini, G.; Cara Romeo, G.; Casaccia, R.; Cifarelli, L.; Cindolo, F.; Contin, A.; D'Ali, G.; Del Papa, C.; Focardi, S.; Iacobucci, G.; Maccarrone, G.; Massam, T.; Motta, F.; Nania, R.; Palmonari, F.; Prisco, G.; Sartorelli, G.; Susinno, G.; Votano, L.; Zichichi, A.; Istituto Nazionale di Fisica Nucleare, Bologna; European Organization for Nuclear Research, Geneva; Istituto Nazionale di Fisica Nucleare, Frascati; Michigan Univ., Ann Arbor; Palermo Univ.

1986-01-01

We have continued the testing of dimethyl ether as a drift-chamber gas in order to improve the understanding of its properties. In particular, we report on measurement accuracy, on systematic effects, and some preliminary data on the ageing of a detector filled with dimethyl ether. (orig.)

Process for making propenyl ethers and photopolymerizable compositions containing them

Science.gov (United States)

Crivello, James V.

1996-01-01

Propenyl ether monomers of formula V A(OCH.dbd.CHCH.sub.3).sub.n wherein n is an integer from one to six and A is selected from cyclic ethers, polyether and alkanes are disclosed. The monomers are readily polymerized in the presence of cationic photoinitiators, when exposed to actinic radiation, to form poly(propenyl ethers) that are useful for coatings, sealants, varnishes and adhesives. Compositions for preparing polymeric coatings comprising the compounds of formula V together with particular cationic photoinitiators are also disclosed, as are processes for making the monomers from allyl halides and readily available alcohols. The process involves rearranging the resulting allyl ethers to propenyl ethers.

RATE CONSTANTS FOR THE REACTIONS OF OH RADICALS AND CL ATOMS WITH DI-N-PROPYL ETHER AND DI-N-BUTYL ETHER AND THEIR DEUTERATED ANALOGS. (R825252)

Science.gov (United States)

Using relative rate methods, rate constants for the gas-phase reactions of OH radicals and Cl atoms with di-n-propyl ether, di-n-propyl ether-d14, di-n-butyl ether and di-n-butyl ether-d18 have been measured at 296 ? 2 K and atmos...

Selective crystallization of cations with crown ethers

International Nuclear Information System (INIS)

Heffels, Dennis Egidius

2014-01-01

The aim of this work was to study the selectivity and preferences of the incorporation of differently sized cations in the cavities of various crown ethers and the characterization of the resulting compounds. The coordination preferences of crown ethers with different cavities have long been known, and the impact of other effects on the structure formation have increasingly become the focus of attention. In this work a comparative overview of the coordination preferences depending on various factors was undertaken. The focus was mainly on the variation of the cavity of the crown ether in the presence of differently sized cations. In addition, the effects of the solvent and differently coordinating anions have been investigated. Within the framework of this work, basic coordination preferences could be detected with rare earth nitrates, which are affected particularly by the choice of the solvent. The formation of different types of structures could be controlled by varying the conditions such that the incorporation of the cation in the cavity of the crown ether was influenced and the formation of a particular type of structure can be influenced partly by the choice of solvent. In this case no direct preferences for the incorporation into the cavity of the crown ether in relation to the cation size were observed for rare earth cations. However, the coordination of the crown ether leads in each case - for lanthanides - to rather high coordination numbers. A total of five new rare earth complexes and two structural variants could be observed with crown ethers. In the study of the selectivity of the incorporation into the cavity, known structures were also reproduced and further structures were characterized but the crystal structures not entirely solved. With the use of monovalent cations such as potassium, lithium or silver a total of nine new compounds could be synthesized, while no clear preferences for the incorporation of certain cations were detected. The

Radiation-induced transformations of cellulose ethers

International Nuclear Information System (INIS)

Nud'ga, L.A.; Petropavlovskii, G.S.; Plisko, E.A.; Isakova, O.V.; Ershov, B.G.

1988-01-01

The purpose of this investigation was to study the transformation which take place under the action of γ-radiation in a number of cellulose ethers containing both saturated (carboxymethyl, hydroxyethyl) and unsaturated (allyl, methacryloyl) groups. Irradiation was carried out on a 60 Co unit in air at 77 and 300 K; the dose rate was 37 and 50 kGy/h respectively. The EPR spectra of γ-irradiated hydroxyethyl- and allylhydroxyethylcelluloses are identical. Under the action of γ-radiation extensive changes took place in cellulose ethers which are exhibited in degradation or the formation of three-dimensional structures and are accompanied by a change in the functional composition. The efficiency in the formation of radicals and their localization are determined by the nature and number of substituents in the cellulose ethers

Thermodynamics of Hydrogen Production from Dimethyl Ether Steam Reforming and Hydrolysis

Energy Technology Data Exchange (ETDEWEB)

T.A. Semelsberger

2004-10-01

The thermodynamic analyses of producing a hydrogen-rich fuel-cell feed from the process of dimethyl ether (DME) steam reforming were investigated as a function of steam-to-carbon ratio (0-4), temperature (100 C-600 C), pressure (1-5 atm), and product species: acetylene, ethanol, methanol, ethylene, methyl-ethyl ether, formaldehyde, formic acid, acetone, n-propanol, ethane and isopropyl alcohol. Results of the thermodynamic processing of dimethyl ether with steam indicate the complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide for temperatures greater than 200 C and steam-to-carbon ratios greater than 1.25 at atmospheric pressure (P = 1 atm). Increasing the operating pressure was observed to shift the equilibrium toward the reactants; increasing the pressure from 1 atm to 5 atm decreased the conversion of dimethyl ether from 99.5% to 76.2%. The order of thermodynamically stable products in decreasing mole fraction was methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol, methyl-ethyl ether and methanol--formaldehyde, formic acid, and acetylene were not observed. The optimal processing conditions for dimethyl ether steam reforming occurred at a steam-to-carbon ratio of 1.5, a pressure of 1 atm, and a temperature of 200 C. Modeling the thermodynamics of dimethyl ether hydrolysis (with methanol as the only product considered), the equilibrium conversion of dimethyl ether is limited. The equilibrium conversion was observed to increase with temperature and steam-to-carbon ratio, resulting in a maximum dimethyl ether conversion of approximately 68% at a steam-to-carbon ratio of 4.5 and a processing temperature of 600 C. Thermodynamically, dimethyl ether processed with steam can produce hydrogen-rich fuel-cell feeds--with hydrogen concentrations exceeding 70%. This substantiates dimethyl ether as a viable source of hydrogen for PEM fuel cells.

Characterization of melt-blended graphene – poly(ether ether ketone) nanocomposite

International Nuclear Information System (INIS)

Tewatia, Arya; Hendrix, Justin; Dong, Zhizhong; Taghon, Meredith; Tse, Stephen; Chiu, Gordon; Mayo, William E.; Kear, Bernard; Nosker, Thomas; Lynch, Jennifer

2017-01-01

Using a high shear melt-processing method, graphene-reinforced polymer matrix composites (G-PMCs) were produced with good distribution and particle–matrix interaction of bi/trilayer graphene at 2 wt. % and 5 wt. % in poly ether ether ketone (2Gn-PEEK and 5Gn-PEEK). The morphology, structure, thermal properties, and mechanical properties of PEEK, 2Gn-PEEK and 5 Gn-PEEK were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), flexural mechanical testing, and dynamic mechanical analysis (DMA). Addition of graphene to PEEK induces surface crystallization, increased percent crystallinity, offers a composite that is thermally stable until 550 °C and enhances thermomechanical properties. Results show that graphene was successfully melt-blended within PEEK using this method.

Characterization of melt-blended graphene – poly(ether ether ketone) nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Tewatia, Arya; Hendrix, Justin [Department of Materials Science and Engineering, Rutgers University, 607 Taylor Road, Piscataway, NJ, 08854 (United States); Dong, Zhizhong [Department of Mechanical Engineering, Rutgers University, 98 Brett Road, Piscataway, NJ 08854 (United States); Taghon, Meredith [Department of Materials Science and Engineering, Rutgers University, 607 Taylor Road, Piscataway, NJ, 08854 (United States); Tse, Stephen [Department of Mechanical Engineering, Rutgers University, 98 Brett Road, Piscataway, NJ 08854 (United States); Chiu, Gordon; Mayo, William E.; Kear, Bernard; Nosker, Thomas [Department of Materials Science and Engineering, Rutgers University, 607 Taylor Road, Piscataway, NJ, 08854 (United States); Lynch, Jennifer, E-mail: jklynch@rci.rutgers.edu [Department of Materials Science and Engineering, Rutgers University, 607 Taylor Road, Piscataway, NJ, 08854 (United States)

2017-02-15

Using a high shear melt-processing method, graphene-reinforced polymer matrix composites (G-PMCs) were produced with good distribution and particle–matrix interaction of bi/trilayer graphene at 2 wt. % and 5 wt. % in poly ether ether ketone (2Gn-PEEK and 5Gn-PEEK). The morphology, structure, thermal properties, and mechanical properties of PEEK, 2Gn-PEEK and 5 Gn-PEEK were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), flexural mechanical testing, and dynamic mechanical analysis (DMA). Addition of graphene to PEEK induces surface crystallization, increased percent crystallinity, offers a composite that is thermally stable until 550 °C and enhances thermomechanical properties. Results show that graphene was successfully melt-blended within PEEK using this method.

On the ether-like Lorentz-breaking actions

International Nuclear Information System (INIS)

Petrov, A.Yu; Nascimento, J.R.; Gomes, M.; Silva, A. J. da

2011-01-01

We demonstrate the generation of the CPT-even, ether-like Lorentz-breaking actions for the scalar and electro-magnetic fields via their appropriate Lorentz-breaking coupling to spinor fields in three, four and five space-time dimensions. Besides, we show that the ether-like terms for the spinor field also can be generated as a consequence of the same couplings. The key result which will be presented here is the finiteness of the ether-like term for the electromagnetic field not only in three and five space-time dimensions where it is natural due to known effects of the dimensional regularization but also in four space-time dimensions. Moreover, we present the calculation of the last result within different calculational schemes and conclude that the result for the four-dimensional ether-like term for the electromagnetic field essentially depending on the calculation scheme, similarly to the result for the Carroll-Field-Jackiw (CFJ) term which probably signalizes a possibility for arising of a new anomaly. Also we discuss the dispersion relations in the theories with ether-like Lorentz-breaking terms which allows to discuss the consistency of the Lorentz-breaking modified theories for different (space-like or time-like) Lorentz-breaking vectors and find the tree-level effective (Breit) potential for fermion scattering and the one-loop effective potential corresponding to the action of the scalar field. (author)

Characterization of Microsolvated Crown Ethers from Broadband Rotational Spectroscopy

Science.gov (United States)

Perez, Cristobal; Schnell, Melanie; Blanco, Susana; Lopez, Juan Carlos

2016-06-01

Since they were first synthetized, crown ethers have been extensively used in organometallic chemistry due to their unparalleled binding selectivity with alkali metal cations. From a structural point of view, crown ethers are heterocycles containing oxygen and/or other heteroatoms, although the most common ones are formed from ethylene oxide unit. Crown ethers are conventionally seen as being hydrophilic inside and hydrophobic outside when the structures found for the metal cation complexes are considered. However, crown ethers are extremely flexible and in isolation may present a variety of stable conformations so that their structure may be easily adapted in presence of a strong ligand as an alkali metal cation minimize the energy of the resulting complex. Water can be considered a soft ligand which interacts with crown ethers through moderate hydrogen bonds. It is thus interesting to investigate which conformers are selected by water to form complexes, the preferred interaction sites and the possible conformational changes due to the presence of one or more water molecules. Previous studies identified microsolvated crown ethers but in all cases with a chromophore group attached to the structure. Here we present a broadband rotational spectroscopy study of microsolvated crown ethers produced in a pulsed molecular jet expansion. Several 1:1 and 1:2 crown ether:water aggregates are presented for 12-crown-4, 15-crown-5 and 18-crown-6. Unambiguous identification of the structures has been achieved using isotopic substitution within the water unit. The subtle changes induced in the structures of the crown ether monomer upon complexation and the hydrogen-bonding network that hold them together will be also discussed. F. Gámez, B. Martínez-Haya, S. Blanco,J. C. López and J. L. Alonso, Phys. Chem. Chem. Phys. 2014, 14 12912-12918 V. A. Shubert, C.W. Müller and T. Zwier, J. Phys. Chem. A 2009, 113 8067-8079

Thermogravimetric analysis of the polymer acrylate-vinyl ether mixture cured by radiation

International Nuclear Information System (INIS)

Danu, Sugiarto

1998-01-01

An experiment on thermal stability of the polymer acrylate-vinyl ether mixture cured by radiation have been done using thermogravimetric analysis. Three kinds of acrylic oligomers i.e., epoxy acrylate, urethane acrylate, and polypropylene glycol diacrylate, and vinyl ether monomers i.e., triethylene glycol divinyl ether (DVE-3), 1,4-cyclohexane dimethanol divinyl ether (CHVE), and butanediol monovinyl ether (HBVE) were used in the experiment. Reaction was taken via radical and cationic polymerisation. In case of cationic polymerisation, diphenyliodonium hexafluorophosphate fotoinisiator was used in the formulation. Thermogravimetric analysis was conducted in a nitrogen atmosphere at a flow rate of 40 ml/minute with a constant heating rate 10 o C and evaluation range were done from 25 to 500 o C. The results of thermogravimetric analysis showed that acrylate and DVE-3 mixture produced the polymer films with higher thermal stability than the mixture of acrylate with CHVE or HBVE. The composition of acrylate-vinyl ether mixture and degree of unsaturation of vinyl ether monomers influenced the thermal stability of polymer. The mixture of epoxy acrylate-vinyl ether and polypropylene glycol diacrylate-vinyl ether have 1 initial decomposition temperature whereas the urethane acrylate-vinyl ether mixture has 2 initial decomposition temperatures. (authors)

Efficacité des néonicotinoïdes et des pyréthrinoïdes utilisés contre le ...

African Journals Online (AJOL)

Efficacité des néonicotinoïdes et des pyréthrinoïdes utilisés contre le foreur des tiges du cacaoyer ( Eulophonotus myrmeleon Felder : Lepidoptera, Cossidae). Implications dans la stratégie de protection de la cacaoculture en Côte d'Ivoire.

Exogenous ether lipids predominantly target mitochondria

DEFF Research Database (Denmark)

Kuerschner, Lars; Richter, Doris; Hannibal-Bach, Hans Kristian

2012-01-01

Ether lipids are ubiquitous constituents of cellular membranes with no discrete cell biological function assigned yet. Using fluorescent polyene-ether lipids we analyzed their intracellular distribution in living cells by microscopy. Mitochondria and the endoplasmic reticulum accumulated high......, accumulated to mitochondria and induced morphological changes and cellular apoptosis. These data indicate that edelfosine could exert its pro-apoptotic power by targeting and damaging mitochondria and thereby inducing cellular apoptosis. In general, this study implies an important role of mitochondria...

Mass transport of direct methanol fuel cell species in sulfonated poly(ether ether ketone) membranes

International Nuclear Information System (INIS)

Silva, V.S.; Ruffmann, B.; Vetter, S.; Boaventura, M.; Mendes, A.M.; Madeira, L.M.; Nunes, S.P.

2006-01-01

Homogeneous membranes based on sulfonated poly(ether ether ketone) (sPEEK) with different sulfonation degrees (SD) were prepared and characterized. In order to perform a critical analysis of the SD effect on the polymer barrier and mass transport properties towards direct methanol fuel cell species, proton conductivity, water/methanol pervaporation and nitrogen/oxygen/carbon dioxide pressure rise method experiments are proposed. This procedure allows the evaluation of the individual permeability coefficients in hydrated sPEEK membranes with different sulfonation degrees. Nafion[reg] 112 was used as reference material. DMFC tests were also performed at 50 deg. C. It was observed that the proton conductivity and the permeability towards water, methanol, oxygen and carbon dioxide increase with the sPEEK sulfonation degree. In contrast, the SD seems to not affect the nitrogen permeability coefficient. In terms of selectivity, it was observed that the carbon dioxide/oxygen selectivity increases with the sPEEK SD. In contrast, the nitrogen/oxygen selectivity decreases. In terms of barrier properties for preventing the DMFC reactants loss, the polymer electrolyte membrane based on the sulfonated poly(ether ether ketone) with SD lower or equal to 71%, although having slightly lower proton conductivity, presented much better characteristics for fuel cell applications compared with the well known Nafion[reg] 112. In terms of the DMFC tests of the studied membranes at low temperature, the sPEEK membrane with SD = 71% showed to have similar performance, or even better, as that of Nafion[reg] 112. However, the highest DMFC overall efficiency was achieved using sPEEK membrane with SD = 52%

Analyse de la sensibilité aux paramètres gazoles d'un moteur diesel d'automobile à injection directe Small Direct Injection Diesel Engine Sensitivity to the Diesel Fuel Characteristics

Directory of Open Access Journals (Sweden)

Montagne X.

2006-12-01

Full Text Available L'étude présentée a été réalisée dans le cadre du GMCL (Groupement Moteur Carburant Lubrifiant, organisme qui réunit des constructeurs d'automobiles, des raffineurs et des additiveurs, avec l'objectif d'examiner la sensibilité d'un moteur Diesel à injection directe d'automobile aux paramètres du gazole. Les partenaires de cette étude sont Elf, IFP, Octel, PSA, Renault et Total. Parmi les solutions technologiques permettant de disposer de convertisseurs d'énergie assurant de faibles niveaux d'émissions de polluants et de consommation, le moteur Diesel se place naturellement en bonne position. Dans ce contexte, on enregistre aujourd'hui l'émergence du moteur Diesel à injection directe pour les véhicules légers en raison de ses performances, notamment en regard de la consommation. Toutefois, cette technologie nécessite une technique d'injection performante, associée à la gestion électronique, demande de l'EGR et un catalyseur d'oxydation afin de régler les problèmes d'émissions polluantes et sonores. Il est donc de première importance de cerner avec précision la sensibilité du moteur Diesel à injection directe aux paramètres carburants afin de tirer le meilleur profit de cette technologie. À partir d'un ensemble de gazoles formulés pour faire varier la composition chimique, l'indice de cétane et la densité, un moteur Audi à injection directe de type 1Z a été testé au banc, dans des conditions standard de réglage (avance à l'injection et taux de gaz recyclés. Cet ensemble de résultats a ainsi permis de démontrer que l'accroissement de l'indice de cétane, la réduction de la densité et de la teneur en polyaromatiques ont une influence positive sensible sur les émissions de CO, d'hydrocarbures imbrûlés, des VOF. En ce qui concerne les émissions de particules, l'indice de cétane semble avoir une influence négative sur la fraction sèche dans certaines conditions. De plus, il apparaît que les

Sulfonated poly(tetramethydiphenyl ether ether ketone) membranes for vanadium redox flow battery application

Energy Technology Data Exchange (ETDEWEB)

Mai, Zhensheng; Bi, Cheng; Dai, Hua [PEMFC Key Materials and Technology Laboratory, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Zhongshan Road 457, Dalian 116023 (China); Graduate University of the Chinese Academy of Sciences, Beijing 100039 (China); Zhang, Huamin; Li, Xianfeng [PEMFC Key Materials and Technology Laboratory, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Zhongshan Road 457, Dalian 116023 (China)

2011-01-01

Sulfonated poly(tetramethydiphenyl ether ether ketone) (SPEEK) with various degree of sulfonation is prepared and first used as ion exchange membrane for vanadium redox flow battery (VRB) application. The vanadium ion permeability of SPEEK40 membrane is one order of magnitude lower than that of Nafion 115 membrane. The low cost SPEEK membranes exhibit a better performance than Nafion at the same operating condition. VRB single cells with SPEEK membranes show very high energy efficiency (>84%), comparable to that of the Nafion, but at much higher columbic efficiency (>97%). In the self-discharge test, the duration of the cell with the SPEEK membrane is two times longer than that with Nafion 115. The membrane keeps a stable performance after 80-cycles charge-discharge test. (author)

Analysis of electron-irradiated poly-ether ether ketone by X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Oyabu, Matashige; Kobayashi, Yoshinori; Seguchi, Tadao; Sasuga, Tsuneo; Kudoh, Hisaaki.

1995-01-01

Organic polymers used in atomic power plants or space are damaged by ionizing irradiation. Radicals produced by irradiation cause oxidation, chain scission and crosslinking, all of which lead to degradation of the material. In this paper, the surface of electron-irradiated poly-ether ether ketone (PEEK) was studied by X-ray photoelectron spectroscopy (XPS). The irradiation in air was found to oxidize the PEEK surface producing carboxyl groups, the content of which dependant on the dose. Carboxyl groups were not produced in helium gas. Quantitative spectral analysis indicated that the aromatic structure might be decomposed. Some comparison was made between the semicrystalline and amorphous samples. The oxygen content resulting from irradiation, of semicrystalline PEEK increased more than that of amorphous PEEK. (author)

Application of simplified PC-SAFT to glycol ethers

DEFF Research Database (Denmark)

Avlund, Ane Søgaard; Kontogeorgis, Georgios; Michelsen, Michael Locht

2012-01-01

The simplified PC-SAFT (sPC-SAFT) equation of state is applied for binary glycol ether-containing mixtures, and it is investigated how the results are influenced by inclusion of intramolecular association in the association theory. Three different glycol ethers are examined: 2-methoxyethanol, 2...

Santé des adolescents et des jeunes au Burkina Faso : état des ...

African Journals Online (AJOL)

Il s'est agi d'une étude évaluative ayant utilisé une revue documentaire associée à une interview des acteurs clés et un atelier de validation et d'identification des interventions pertinentes pour un plan stratégique national. La situation de la santé des adolescents et des jeunes est caractérisée par des grossesses précoces ...

Origin of mechanical modifications in poly (ether ether ketone)/carbon nanotube composite

International Nuclear Information System (INIS)

Pavlenko, Ekaterina; Puech, Pascal; Bacsa, Wolfgang; Boyer, François; Olivier, Philippe; Sapelkin, Andrei; King, Stephen; Heenan, Richard; Pons, François; Gauthier, Bénédicte; Cadaux, Pierre-Henri

2014-01-01

Variations in the hardness of a poly (ether ether ketone) beam electrically modified with multi-walled carbon nanotubes (MWCNT, 0.5%-3%) are investigated. It is shown that both rupture and hardness variations correlate with the changes in carbon nanotube concentration when using micro indentation and extended Raman imaging. Statistical analysis of the relative spectral intensities in the Raman image is used to estimate local tube concentration and polymer crystallinity. We show that the histogram of the Raman D band across the image provides information about the amount of MWCNTs and the dispersion of MWCNTs in the composite. We speculate that we have observed a local modification of the ordering between pure and modified polymer. This is partially supported by small angle neutron scattering measurements, which indicate that the agglomeration state of the MWCNTs is the same at the concentrations studied.

Origin of mechanical modifications in poly (ether ether ketone)/carbon nanotube composite

Energy Technology Data Exchange (ETDEWEB)

Pavlenko, Ekaterina; Puech, Pascal; Bacsa, Wolfgang, E-mail: wolfgang.bacsa@cemes.fr [CEMES-CNRS and University of Toulouse, 29 Jeanne Marvig, 31055 Toulouse (France); Boyer, François; Olivier, Philippe [Université de Toulouse, Institut Clément Ader, I.U.T. Université Paul Sabatier - 133C Avenue de Rangueil - B.P. 67701, 31077 Toulouse CEDEX 4 (France); Sapelkin, Andrei [School of Physics and Astronomy, Queen Mary, University of London, Mile End Road, E1 4NS London (United Kingdom); King, Stephen; Heenan, Richard [ISIS Facility, Rutherford Appleton Laboratory, Chilton, OX11 0QX Didcot (United Kingdom); Pons, François; Gauthier, Bénédicte; Cadaux, Pierre-Henri [AIRBUS FRANCE (B.E. M and P Toulouse), 316 Route de Bayonne, 31060 Toulouse (France)

2014-06-21

Variations in the hardness of a poly (ether ether ketone) beam electrically modified with multi-walled carbon nanotubes (MWCNT, 0.5%-3%) are investigated. It is shown that both rupture and hardness variations correlate with the changes in carbon nanotube concentration when using micro indentation and extended Raman imaging. Statistical analysis of the relative spectral intensities in the Raman image is used to estimate local tube concentration and polymer crystallinity. We show that the histogram of the Raman D band across the image provides information about the amount of MWCNTs and the dispersion of MWCNTs in the composite. We speculate that we have observed a local modification of the ordering between pure and modified polymer. This is partially supported by small angle neutron scattering measurements, which indicate that the agglomeration state of the MWCNTs is the same at the concentrations studied.

La fabrique des sciences des institutions aux pratiques

CERN Document Server

Benninghoff, Martin; Crettaz von Roten, Fabienne; Merz, Martina

2006-01-01

Aujourd'hui, les façons de produire, d'organiser, d'évaluer et d'utiliser les savoirs sont en profond débat. De plus en plus, l'Etat, la société civile et l'économie tentent d'influencer les activités des universités et des laboratoires de recherche. Ces développements mettent à l'épreuve tout à la fois les fondements des systèmes d'enseignement supérieur et de recherche, l'autonomie des institutions scientifiques, la définition des frontières des savoirs et l'acceptation des sciences. Dans des contextes suisses et européens, cet ouvrage s'intéresse aux manières dont les sciences et les technologies sont fabriquées, en analysant leurs institutions et les pratiques. A partir d'une approche relationnelle, les sciences et les technologies sont conçues comme des phénomènes profondément sociaux, culturels et politiques. Une telle démarche déstabilise les visions parfois idéalisées et stéréotypées de la construction des savoirs. Des études de cas détaillées décrivent des phénomè...

Some observations on the carburization of type 316 stainless steel foil in a low carbon activity sodium environment

International Nuclear Information System (INIS)

Thorley, A.W.; Jeffcoat, P.J.

1982-01-01

Work currently being undertaken to establish the equilibrium composition of carbides which form in stainless steel foils during their exposure to low carbon activity sodium environment is described. The time it takes the carbon to reach equilibrium during exposure to sodium of different carbon activity is discussed. The lowest carbon activity measureable in test loops where the sodium is just above carburizing to stainless steel is reported. Analytical techniques are used to determine the composition of the carbide and the austenite matrix and hence estimate the carbon activity of the equilibrium structure. This provides a comparison with carbon activity values determined by alternative methods such as the Harwell Carbon Meter and nickel tab techniques

Radiation chemistry of alternative fuel oxygenates - substituted ethers

International Nuclear Information System (INIS)

Mezyk, S. P.; Cooper, W. J.; Bartels, D. M.; Tobien, T.; O'Shea, K. E.

1999-01-01

The electron beam process, an advanced oxidation and reduction technology, is based in the field of radiation chemistry. Fundamental to the development of treatment processes is an understanding of the underlying chemistry. The authors have previously evaluated the bimolecular rate constants for the reactions of methyl tert-butyl ether (MTBE) and with this study have extended their studies to include ethyl tert-butyl ether (ETBE), di-isopropyl ether (DIPE) and tert-amyl methyl ether (TAME) with the hydroxyl radical, hydrogen atom and solvated electron using pulse radiolysis. For all of the oxygenates the reaction with the hydroxyl radical appears to be of primary interest in the destruction of the compounds in water. The rates with the solvated electron are limiting values as the rates appear to be relatively low. The hydrogen atom rate constants are relatively low, coupled with the low yield in radiolysis, they concluded that these are of little significance in the destruction of the alternative fuel oxygenates (and MTBE)

Diethyl Ether Production as a Substitute for Gasoline

Directory of Open Access Journals (Sweden)

Alviany Riza

2018-01-01

Full Text Available Diethyl ether is one of alternative fuel that could be used as a significant component of a blend or as a complete replacement for transportation fuel. The aim of this research is to produce diethyl ether through dehydration reaction of ethanol with fixed bed reactor using nanocrystalline γ-Al2O3 catalyst. Nanocrystalline γ-Al2O3 catalyst was synthesized by precipitation method using Al(NO33.9H2O as precursors and NH4OH as the precipitating agent. Dehydration reaction was performed at temperature range of 125 to 225°C. The result shows that synthesized γ-Al2O3 catalyst gave higher ethanol conversion and diethyl ether yield than that of commercial Al2O3 catalyst. The use of synthesized γ-Al2O3 catalyst could reach ethanol conversion as high as 94.71% and diethyl ether yield as high as 11,29%.

A highly sensitive and selective dimethyl ether sensor based on cataluminescence.

Science.gov (United States)

Zhang, Runkun; Cao, Xiaoan; Liu, Yonghui; Peng, Yan

2010-07-15

A sensor for detecting dimethyl ether was designed based on the cataluminescence phenomenon when dimethyl ether vapors were passing through the surface of the ceramic heater. The proposed sensor showed high sensitivity and selectivity to dimethyl ether at an optimal temperature of 279 degrees C. Quantitative analysis were performed at a wavelength of 425 nm, the flow rate of carrier air is around 300 mL/min. The linear range of the cataluminescence intensity versus concentration of dimethyl ether is 100-6.0x10(3) ppm with a detection limit of 80 ppm. The sensor response time is 2.5 s. Under the optimized conditions, none or only very low levels of interference were observed while the foreign substances such as benzene, formaldehyde, ammonia, methanol, ethanol, acetaldehyde, acetic acid, acrolein, isopropyl ether, ethyl acetate, glycol ether and 2-methoxyethanol were passing through the sensor. Since the sensor does not need to prepare and fix up the granular catalyst, the simple technology reduces cost, improves stability and extends life span. The method can be applied to facilitate detection of dimethyl ether in the air. The possible mechanism of cataluminescence from the oxidation of dimethyl ether on the surface of ceramic heater was discussed based on the reaction products. Copyright 2010 Elsevier B.V. All rights reserved.

Unitary information ether and its possible applications

International Nuclear Information System (INIS)

Horodecki, R.

1991-01-01

The idea of information ether as the unitary information field is developed. It rests on the assumption that the notion of information is a fundamental category in the description of reality and that it can be defined independently from the notion of probability itself. It is shown that the information ether provides a deterministic background for the nonlinear wave hypothesis and quantum cybernetics. (orig.)

The Ether Wind and the Global Positioning System.

Science.gov (United States)

Muller, Rainer

2000-01-01

Explains how students can perform a refutation of the ether theory using information from the Global Positioning System (GPS). Discusses the functioning of the GPS, qualitatively describes how position determination would be affected by an ether wind, and illustrates the pertinent ideas with a simple quantitative model. (WRM)

Synthesis of Poly(vinyl ether) Thermoplastic Elastomers Having Functional Soft Segments

OpenAIRE

今枝, 嗣人; 漆崎, 美智遠; 阪口, 壽一; 橋本, 保; Tsuguto, IMAEDA; Michio, URUSHISAKI; Toshikazu, SAKAGUCHI; Tamotsu, HASHIMOTO

2013-01-01

The ABA-type triblock copolymers consisting of poly(2-adarnantyl vinyl ether) [poly(2-AdVE) as outer hard segments and poly(6-acetoxyhexyl vinyl ether) [poly(AcHVE)] poly(6-hydroxyhexyl vinyl ether) [poly(H HVE)], or poly(2-(2-methoxyethoxy)ethyl vinyl ether [poly(MOEOVE)] as inner soft segments were synthesized by sequential living cationic polymerization. Despite the presence of polar functional groups such as ester, hydroxy, and oxyethylene units in their soft segments, the two polymer seg...

The breakdown of vinyl ethers as a two-center synchronous reaction

Science.gov (United States)

Pokidova, T. S.; Shestakov, A. F.

2009-11-01

The experimental data on the molecular decomposition of vinyl ethers of various structures to alkanes and the corresponding aldehydes or ketones in the gas phase were analyzed using the method of intersecting parabolas. The enthalpies and kinetic parameters of decomposition were calculated for 17 reactions. The breakdown of ethers is a two-center concerted reaction characterized by a very high classical potential barrier to the thermally neutral reaction (180-190 kJ/mol). The kinetic parameters (activation energies and rate constants) of back reactions of the formation of vinyl ethers in the addition of aldehydes or ketones to alkanes were calculated using the method of intersecting parabolas. The factors that influenced the activation energy of the decomposition and formation of ethers were discussed. Quantum-chemical calculations of several vinyl ether decomposition reactions were performed. Ether formation reactions were compared with the formation of unsaturated alcohols as competitive reactions, which can occur in the interaction of carbonyl compounds with alkenes.

Fast liquid chromatography-tandem mass spectrometry for the analysis of bisphenol A-diglycidyl ether, bisphenol F-diglycidyl ether and their derivatives in canned food and beverages.

Science.gov (United States)

Gallart-Ayala, H; Moyano, E; Galceran, M T

2011-03-25

In this work a fast liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS) method using a C18 Fused Core™ column, was developed for the simultaneous analysis of bisphenol A diglycidyl ether (BADGE), bisphenol A (2,3-dihydroxypropyl) glycidyl ether (BADGE·H(2)O), bisphenol A bis(2,3-dihydroxypropyl) ether (BADGE·2H(2)O), bisphenol A (3-chloro-2-hydroxypropyl) glycidyl ether (BADGE·HCl), bisphenol A bis(3-chloro-2-hydroxypropyl) ether (BADGE·2HCl) and bisphenol A (3-chloro-2-hydroxypropyl)(2,3-dihydroxypropyl ether) (BADGE·HCl·H(2)O) and bisphenol F diglycidyl ether (BFDGE), bisphenol F bis(2,3-dihydroxypropyl) ether (BFDGE·2H(2)O), bisphenol F bis(3-chloro-2-hydroxypropyl) ether (BFDGE·2HCl). The LC method was coupled with a triple quadrupole mass spectrometer, using an ESI source in positive mode and using the [M+NH(4)](+) adduct as precursor ion for tandem mass spectrometry experiments. The method developed was applied to the determination of these compounds in canned soft drinks and canned food. OASIS HLB solid phase extraction (SPE) cartridges were used for the analysis of soft drinks, while solid canned food was extracted with ethyl acetate. Method limits of quantitation ranged from 0.13 μgL(-1) to 1.6 μgL(-1) in soft drinks and 1.0 μgkg(-1) to 4.0 μgkg(-1) in food samples. BADGE·2H(2)O was detected in all the analyzed samples, while other BADGEs such as BADGE·H(2)O, BADGE·HCl·H(2)O, BADGE·HCl and BADGE·2HCl were also detected in canned foods. Copyright © 2011 Elsevier B.V. All rights reserved.

Zircon Carburation Studies as Intermediate Stage in the Zirconium Fabrication; Estudios encaminados a la carburacion del circon como etapa intermedia en la obtencion de circonio

Energy Technology Data Exchange (ETDEWEB)

Almagro Huertas, V; Saenz de Tejada Gonzalez, L.; Lopez Rodriguez, M

1963-07-01

Zirconium carbide and carbonitride mixtures were obtained by Kroll's method.Reaction products have been identified by micrography and X-ray diffraction analysis. The optimum graphite content in the initial charge for the carburation reaction has been studied. zirconium, silicon and carbon content in the final product has been controlled as a function of current in the furnace and reaction time.Further chlorination of the final product was performed successfully. (Author) 16 refs.

Zircon Carburation Studies as Intermediate Stage in the Zirconium Fabrication; Estudios encaminados a la carburacion del circon como etapa intermedia en la obtencion de circonio

Energy Technology Data Exchange (ETDEWEB)

Almagro Huertas, V.; Saenz de Tejada Gonzalez, L.; Lopez Rodriguez, M.

1963-07-01

Zirconium carbide and carbonitride mixtures were obtained by Kroll's method.Reaction products have been identified by micrography and X-ray diffraction analysis. The optimum graphite content in the initial charge for the carburation reaction has been studied. zirconium, silicon and carbon content in the final product has been controlled as a function of current in the furnace and reaction time.Further chlorination of the final product was performed successfully. (Author) 16 refs.

Effect of p-amino-diphenyl ethers on hepatic microsomal cytochrome P450.

Science.gov (United States)

Jiang, Huidi; Xuan, Guida

2003-09-01

The present paper aims to investigate whether p-amino-2',4'-dichlorodiphenyl ether and p-amino-4'-methyldiphenyl ether are inhibitors as well as inducers of P450. Mice were given daily intraperitoneal (ip) injections of p-amino-2',4'-dichlorodiphenyl ether (0.25 mmol/kg) or p-amino-4'-methyldiphenyl ether (0.25 mmol/kg) for 4 days and tested at 24 h and 48 h after the last dose injection. The results showed the mice pentobarbital sleeping time was shorter and the P450 content of hepatic microsome increased significantly in the group pretreated with p-amino-4'-methyldiphenyl ether when compared with the control group, while in mice pretreated with p-amino-2',4'-dichlorodiphenyl ether the hepatic microsome P450 content increased but the pentobarbital sleeping time was extended in clear contrast to the control group. The sleeping time of the phenobarbital group (80 mg/kg daily ip injection for 4 days) was shortened at 24 h after the last injection with increased P450 content of hepatic microsome, but it showed no difference at 48 h. The zoxazolamine-paralysis times of mice treated with p-amino-2',4'-dichlorodiphenyl ether were longer than those of the control mice, while the same dose of zoxazolamine did not lead to paralysis in mice pretreated with BNF. p-Amino-2',4'-dichlorodiphenyl ether and p-amino-4'-methyldiphenyl ether inhibited the activity of 7-ethoxyresorufin O-deethylase from rat hepatic microsome induced by BNF in vitro by 70.0% and 50.1% respectively. These results suggest that p-amino-2',4'-dichlorodiphenyl ether and p-amino-4'-methyldiphenyl ether are inhibitors as well as inducers of P450.

Iminoéthers-1 3 cycliques : chimie et applications dans le domaine des additifs pétroliers et des matériaux organiques Cyclic 1,3-Iminoethers: Chemistry and Applications in the Field of Petroleum Additives and Organic Materials

Directory of Open Access Journals (Sweden)

Le Perchec P.

2006-11-01

Full Text Available Cet article est consacré aux iminoéthers-1,3 cycliques les plus courants : les oxazines-1,3 et oxazolines-1,3. La première partie rappelle les synthèses de ces composés et quelques aspects récents de leur chimie : réactions d'hydrolyse, réactions de déprotonation avec ouverture de cycle, réactions des organométalliques, réactions d'addition des nucléophiles en positions 2 et 5, des sels d'iminoéthers correspondants, propriétés complexantes vis-à-vis des métaux, réactions d'aminolyse et formation de structures tensioactives, enfin polymérisations et copolymérisations cationiques. La seconde partie est consacrée à l'étude des travaux qui traitent des applications. En ce qui concerne le domaine des additifs pétroliers, on s'intéresse à la stabilité du cycle oxazoline et à son caractère polaire. Les dérivés tensioactifs dérivés d'oxazoline portant des chaînes hydrocarbonées ont été revendiqués comme additifs dispersants et multifonctionnels pour les carburants et les lubrifiants. De nombreuses formulations (dispersants, antioxydants antirouilles, antiusures, extrême pressions, réducteurs de frictions. . . ont été proposées. Certains dérivés d'hydroxyméthyl oxazolines présentent des propriétés lubrifiantes et d'autres ont un intérêt dans les formulations de boues de forage. En ce qui concerne le domaine des matériaux, on s'intéresse à la réactivité du cycle oxazoline pour réaliser soit des extensions de chaînes des thermoplastiques, soit des réticulations pour des applications de peintures et revêtements. Les homopolymères d'oxazoline qui ont un caractère polaire très marqué peuvent trouver des applications comme promoteur d'adhésion, ou tensioactifs pour les polymérisations en émulsion. Enfin, l'utilisation d'oxazolines stables a été revendiquée dans des formulations de vernis d'émaillage. This article deals with the most common cyclic 1,3-iminoethers, i. e. 1,3-oxazines and 1

Poly(mono/diethylene glycol n-tetradecyl ether vinyl ethers with Various Molecular Weights as Phase Change Materials

Directory of Open Access Journals (Sweden)

Dongfang Pei

2018-02-01

Full Text Available At present, research on the relationship of comb-like polymer phase change material structures and their heat storage performance is scarce. Therefore, this relationship from both micro and macro perspectives will be studied in this paper. In order to achieve a high phase change enthalpy, ethylene glycol segments were introduced between the vinyl and the alkyl side chains. A series of poly(mono/diethylene glycol n-tetradecyl ether vinyl ethers (PC14EnVEs (n = 1, 2 with various molecular weights were polymerized by living cationic polymerization. The results of PC14E1VE and PC14E2VE showed that the minimum number of carbon atoms required for side-chain crystallization were 7.7 and 7.2, which were lower than that reported in the literature. The phase change enthalpy 89 J/g (for poly(mono ethylene glycol n-tetradecyl ether vinyl ethers and 86 J/g (for poly(hexadecyl acrylate were approximately equal. With the increase of molecular weight, the melting temperature, the melting enthalpy, and the initial thermal decomposition temperature of PC14E1VE changed from 27.0 to 28.0 °C, from 95 to 89 J/g, and from 264 to 287 °C, respectively. When the number average molar mass of PC14EnVEs exceeded 20,000, the enthalpy values remained basically unchanged. The introduction of the ethylene glycol chain was conducive to the crystallization of alkyl side chains.

Tombes et cimetières éthiopiens : des rois, des saints, des anonymes1

OpenAIRE

Derat, Marie-Laure

2009-01-01

L’histoire des tombes et cimetières éthiopiens, dans la longue durée, en est encore à ses balbutiements. Si les tombes des saints et des rois nous sont un peu mieux connus grâce à des textes témoignant à la fois des enjeux entourant les sépultures de ces personnages hors du commun et des soins apportés à leur inhumation, en revanche, les cimetières ordinaires échappent encore largement à l’enquête, en grande partie parce que le commun des mortels est inhumé dans l’anonymat et dans un grand dé...

Évaluation des pratiques agricoles des légumes feuilles : le cas des ...

African Journals Online (AJOL)

Face à ce constat, le défi de la recherche serait la détermination du niveau actuel de contamination des légumes feuilles et des eaux du barrage et celui de l'État serait l'initiation de programmes de sensibilisation des producteurs par rapport à une gestion plus rigoureuse des pesticides. Mots-clés : pratiques paysannes, ...

Sulfonated polyphenyl ether by electropolymerization

International Nuclear Information System (INIS)

Hou Hongying; Vacandio, Florence; Di Vona, Maria Luisa; Knauth, Philippe

2012-01-01

Highlights: ► Sulfonated polyphenyl ether was for the first time electropolymerized. ► This technique allows the economical preparation of ionomeric membranes for electrochemical energy technologies. ► The mechanism of electropolymerization was discussed in detail. - Abstract: Electropolymerization of sulfonated phenol was for the first time achieved and studied by cyclic voltammetry (CV) and chronoamperometry on stainless steel substrates. The obtained sulfonated polyphenyl ether was characterized in terms of impedance spectroscopy, nuclear magnetic resonance (NMR), energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD) and Fourier-Transform Infrared (FTIR) spectroscopy. Dense films of micrometer thickness can be obtained; the proton conductivity is about 3 mS/cm at room temperature.

Diethyl Ether Production Process with Various Catalyst Type

Directory of Open Access Journals (Sweden)

Widayat Widayat

2012-12-01

Full Text Available Several H-zeolite and HZSM-5 catalysts was preparated and their characters have also been investigated. H-zeolit Catalyst was preparated from Natural Zeolite that obtained from Malang District and Gunung Kidul District. Diethyl ether was produced by Ethanol with concentration of 95%. This research use fixed bed reactor that 1 gram of catalyst as bed catalyst, atmospheric pressure and temperature 140oC as the operating condition. Ethanol vapor from vaporization tank was driven by 200 ml/min Nitrogen stream. The responds in this research is liquid product concentration; diethyl ether, ethanol, methanol and water concentration. The results showed that the largest ethanol conversion was produced by the use of 56.44% HZSM-5 and the largest yield of diethyl ether diethyl was produced by the use of alumina and H-zeolite catalyst. The larger ratio between natural zeolite with HCl solvent will produce the larger surface area of catalyst and ethanol conversion. The largest ethanol conversion was produced at reactan ratio 1:20. [Keywords:  catalyst; ethanol conversion; dehydration process; yield of diethyl ether; natural zeolite].

La convergence des rôles respectifs des relationnistes et des journalistes influence-t-elle la perception qu'ils ont les uns des autres?

DEFF Research Database (Denmark)

Valentini, Chiara

2017-01-01

la convergence des rôles respectifs des praticiens des relations publiques et des journalistes a un effet favorable sur la perception qu’ils ont les uns des autres. L’effet est plus marqué chez les praticiens des relations publiques, car leur vision de la profession en journalisme correspond à celle...

Mécanique des sols et des roches

CERN Document Server

Vullier, Laurent; Zhao, Jian

2016-01-01

La mécanique des sols et la mécanique des roches sont des disciplines généralement traitées séparément dans la littérature. Pour la première fois, un traité réunit ces deux spécialités, en intégrant également les connaissances en lien avec les écoulements souterrains et les transferts thermiques. A la fois théorique et pratique, cet ouvrage propose tout d'abord une description détaillée de la nature et de la composition des sols et des roches, puis s'attache à la modélisation de problèmes aux conditions limites et présente les essais permettant de caractériser les sols et les roches, tant d'un point de vue mécanique qu'hydraulique et thermique. La problématique des sols non saturés et des écoulements multiphasiques est également abordée. Une attention particulière est portée aux lois de comportement mécanique et à la détermination de leurs paramètres par des essais in situ et en laboratoire, et l'ouvrage offre également une présentation détaillée des systèmes de classi...

Preliminary Investigation of Poly-Ether-Ether-Ketone Based on Fused Deposition Modeling for Medical Applications

Directory of Open Access Journals (Sweden)

Feng Zhao

2018-02-01

Full Text Available Poly-ether-ether-ketone (PEEK fabricated by fused deposition modeling for medical applications was evaluated in terms of mechanical strength and in vitro cytotoxicity in this study. Orthogonal experiments were firstly designed to investigate the significant factors on tensile strength. Nozzle temperature, platform temperature, and the filament diameter were tightly controlled for improved mechanical strength performance. These sensitive parameters affected the interlayer bonding and solid condition in the samples. Fourier transform infrared (FTIR spectrometry analysis was secondly conducted to compare the functional groups in PEEK granules, filaments, and printed parts. In vitro cytotoxicity test was carried out at last, and no toxic substances were introduced during the printing process.

Bimetallic NiFe2O4 synthesized via confined carburization in NiFe-MOFs for efficient oxygen evolution reaction

Science.gov (United States)

Fang, Zhiqiang; Hao, Zhaomin; Dong, Qingsong; Cui, Yong

2018-04-01

Transition metal oxides that derived from metal-organic framework (MOF) precursor have intensively received attention because of their numerous electrochemical applications. Bimetallic Ni-Fe oxides have been rarely reported on the basis of MOF-related strategy. Herein, a bimetallic NiFe2O4 was successfully synthesized via confined carburization in NiFe-MOF precursors and characterized by XRD, XPS, SEM, and TEM. After conducting an investigation of oxygen evolution reaction (OER), the as-synthesized NiFe2O4 material exhibited good catalytic efficiency and high stability and durability in alkaline media. The as-synthesized NiFe2O4 material would promote the development of MOFs in non-noble-metal OER catalyst.

Densely quaternized poly(arylene ether)s with distinct phase separation for highly anion-conductive membranes

Science.gov (United States)

Hu, Yuanfang; Wang, Bingxi; Li, Xiao; Chen, Dongyang; Zhang, Weiying

2018-05-01

To develop high performance anion exchange membranes (AEMs), a novel bisphenol monomer bearing eight benzylmethyl groups at the outer edge of the molecule was synthesized, which after condensation polymerization with various amounts of 4,4‧-dihydroxydiphenylsulfone and 4,4‧-difluorobenzophenone yielded novel poly(arylene ether)s with densely located benzylmethyl groups. These benzylmethyl groups were then converted to quaternary ammonium groups by radical-initiated bromination and quaternization in tandem, leading to the emergence of densely quaternized poly(arylene ether sulfone)s (QA-PAEs) with controlled ion exchange capacities (IECs) ranging from 1.61 to 2.32 mmol g-1. Both small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) studies revealed distinct phase separation in the QA-PAEs. The QA-PAE-40 with an IEC of 2.32 mmol g-1 exhibited a Br- conductivity of 9.2 mS cm-1 and a SO42- conductivity of 14.0 mS cm-1 at room temperature, much higher than those of a control membrane with a similar IEC but without obvious phase separation. Therefore, phase separation of AEMs was validated to be advantageous for the efficient conducting of anions. The experimental results also showed that the QA-PAEs were promising AEM materials, especially for non-alkaline applications.

Évaluation des pratiques agricoles des légumes feuilles : le cas des ...

African Journals Online (AJOL)

SARAH

30 sept. 2017 ... ... de Biochimie et Immunologie Appliquée, Centre de Recherche en Sciences Biologiques, Alimentaires et .... l'intoxication des agriculteurs et des consommateurs, ... source d'alimentation en eau et au pouvoir d'achat des.

40 CFR 721.10017 - Amine terminated bisphenol A diglycidyl ether polymer (generic).

Science.gov (United States)

2010-07-01

... diglycidyl ether polymer (generic). 721.10017 Section 721.10017 Protection of Environment ENVIRONMENTAL... ether polymer (generic). (a) Chemical substances and significant new uses subject to reporting. (1) The chemical substances identified generically as amine terminated bisphenol A diglycidyl ether polymer (PMNs P...

Les possibilités de limitation des émissions de plomb par les véhicules automobiles Possibilities of Limiting Leaded Exhaust from Automotive Vehicles

Directory of Open Access Journals (Sweden)

Roth J.

2006-11-01

Full Text Available Les additifs plombés permettent de satisfaire les besoins en octane des moteurs automobiles actuels. Dans le cadre de la lutte contre la pollution automobile, il est envisagé de réduire ou de supprimer le plomb présent dans les carburants. La suppression brutale, tout en présentant certains avantages, entraîne de nombreux inconvénients, d'ordre purement technique mais également d'ordre financier. La mise au point d'un dispositif de captation, par les sociétés Texaco et Octel, semble permettre d'envisager de maintenir la présence de plomb dans les carburants, tout en réduisant les émissions à l'échappement. Les travaux effectués à l'UTAC ont permis de tester ces dispositifs sur une endurance de 31 000 km. Les résultats obtenus ont permis de dégager un gain d'efficacité d'environ 60 %, les paramètres, bruit et pollution (CO et HC restant par ailleurs inchangés. Leaded additives enable the octane requirements of existing automotive engines to be satisfied. However, as part of the fight against automotive pollution, plans are being drawn up to reduce or eliminate the lead present in fuels. A sudden elimination, although having some advantages, would create a great many disadvantages of a purely technical as well as financiel nature. Texaco and Octet have developed a trapping device that appears to enable lead to be retained in fuels at the same time as reducing exhaust emissions. This device has undergone a 31,000-kilometer endurance test at UTAC. The results reveal an efficiency gain of 60 %, while the noise and pollution (CO and HC parameters remain the same.

Congenital malformations and maternal occupational exposure to glycol ethers

NARCIS (Netherlands)

Cordier, S; Bergeret, A; Goujard, J; Ha, MC; Ayme, S; Calzolari, E; DeWalle, HEK; KnillJones, R; Candela, S; Dale, [No Value; Dananche, B; deVigan, C; Fevotte, J; Kiel, G; Mandereau, L

Glycol ethers are found in a wide range of domestic and industrial products, many of which are used in women's work environments. Motivated by concern about their potential reproductive toxicity, we have evaluated the risk of congenital malformations related to glycol ether exposure during preg

Wear of tin coating and Al-Si alloy substrate against carburized steel under mixed lubrication

Science.gov (United States)

Wang, Q.; Cheng, H. S.; Fine, M. E.

1994-04-01

Tin coatings on Al-Si alloys are widely used in the automotive industries. The soft tin coating and the harder substrate alloy form a tribological system with the advantages of low friction and reasonably high load-bearing capacity. Wear tests of tin coated Al-Si Z332 alloy in conformal contact against carburized 1016 steel have been carried out under mixed lubrications with SAE 10W30 oil to study the wear mechanisms. Two major wear mechanisms, uniform wear of the tin coating due to micro-plowing and spall pitting related to the substrate are found to contribute to the bearing material loss when the fluid lubrication film is relatively thick (Lambda about 1.6). Under conditions of thinner films (Lambda approximately = 0.8), some local coating debonding occurs. The pitting and local coating debounding are closely related to fracture in the substrate. The bonding between silicon and tin seems to be weaker than between aluminum and tin. During wear, oxidation occurs.

Modelisation des effets physico-techniques pour la conception des ...

African Journals Online (AJOL)

automatisation dans les installations industrielles a besoin d'une régulation automatique des commandes des processus technologiques pour lesquelles certaines contraintes sont à relever compte tenu des exigences des innovations scientifiques de ...

Vecteurs Singuliers des Theories des Champs Conformes Minimales

Science.gov (United States)

Benoit, Louis

En 1984 Belavin, Polyakov et Zamolodchikov revolutionnent la theorie des champs en explicitant une nouvelle gamme de theories, les theories quantiques des champs bidimensionnelles invariantes sous les transformations conformes. L'algebre des transformations conformes de l'espace-temps presente une caracteristique remarquable: en deux dimensions elle possede un nombre infini de generateurs. Cette propriete impose de telles conditions aux fonctions de correlations qu'il est possible de les evaluer sans aucune approximation. Les champs des theories conformes appartiennent a des representations de plus haut poids de l'algebre de Virasoro, une extension centrale de l'algebre conforme du plan. Ces representations sont etiquetees par h, le poids conforme de leur vecteur de plus haut poids, et par la charge centrale c, le facteur de l'extension centrale, commune a toutes les representations d'une meme theorie. Les theories conformes minimales sont constituees d'un nombre fini de representations. Parmi celles-ci se trouvent des theories unitaires dont les representation forment la serie discrete de l'algebre de Virasoro; leur poids h a la forme h_{p,q}(m)=[ (p(m+1) -qm)^2-1] (4m(m+1)), ou p,q et m sont des entiers positifs et p+q= 2. Ces representations possedent un sous-espace invariant engendre par deux sous-representations avec h_1=h_{p,q} + pq et h_2=h_{p,q} + (m-p)(m+1-q) dont chacun des vecteurs de plus haut poids portent le nom de vecteur singulier et sont notes respectivement |Psi _{p,q}> et |Psi_{m-p,m+1-q}>. . Les theories super-conformes sont une version super-symetrique des theories conformes. Leurs champs appartiennent a des representation de plus haut poids de l'algebre de Neveu-Schwarz, une des deux extensions super -symetriques de l'algebre de Virasoro. Les theories super -conformes minimales possedent la meme structure que les theories conformes minimales. Les representations sont elements de la serie h_{p,q}= [ (p(m+2)-qm)^2-4] /(8m(m+2)) ou p,q et m sont

Direct transformation of silyl enol ethers into functionalized allenes.

Science.gov (United States)

Langer, P; Döring, M; Seyferth, D; Görls, H

2001-02-02

The first elimination reactions of silyl enol ethers to lithiated allenes are reported. These reactions allow a direct transformation of readily available silyl enol ethers into functionalized allenes. The action of three to four equivalents of lithium diisopropylamide (LDA) on silyl enol ethers results in the formation of lithiated allenes by initial allylic lithiation, subsequent elimination of a lithium silanolate, and finally, lithiation of the allene thus formed. Starting with amide-derived silyl imino ethers, lithiated ketenimines are obtained. A variety of reactions of the lithiated allenes with electrophiles (chlorosilanes, trimethylchlorostannane, dimethyl sulfate and ethanol) were carried out. Elimination of silanolate is observed only for substrates that contain the hindered SiMe2tBu or Si(iPr)3 moiety, but not for the SiMe3 group. The reaction of 1,1-dilithio-3,3-diphenylallene with ketones provides a convenient access to novel 1,1-di(hydroxymethyl)allenes which undergo a domino Nazarov-Friedel-Crafts reaction upon treatment with p-toluenesulfonic acid.

Williamson alkylation approach to the synthesis of poly(alkyl vinyl ether) copolymers

International Nuclear Information System (INIS)

Markova, D.; Christova, D.; Velichkova, R.

2008-01-01

A method for synthesis of poly(alkyl vinyl ether-co-vinyl alcohol) copolymers was developed based on the Williamson's alkylation of poly(vinyl acetate) (PVAc) with alkyl iodides. The influence of the alkylating agent and the reaction conditions on the efficiency of the modification reaction was investigated. The copolymers obtained were characterized by means of 1 H NMR and GPC. It was proved that by applying the proposed method copolymers of different composition and properties containing methyl vinyl ether, ethyl vinyl ether as well as n-butyl vinyl ether units could be prepared. Poly(methyl vinyl ether-co-vinyl alcohol)s of high degree of methylation exhibit sharp temperature response at 38-39 deg C in aqueous solution typical of the so-called smart polymers. (authors)

Utilisation sans risque des eaux usées, des excréta et des eaux ...

International Development Research Centre (IDRC) Digital Library (Canada)

Les responsables de ce projet piloteront l'application et l'adaptation des principes directeurs relatifs à l'utilisation sans risque des eaux usées, des excreta et des eaux grises en agriculture et en aquaculture (Guidelines for the Safe Use of Wastewater, Excreta and Greywater in Agriculture and Aquaculture), que ...

X-ray photoelectron spectroscopy investigation of the carburization of 310 stainless steel

International Nuclear Information System (INIS)

Tabet, N.; Allam, I.; Yin, R.C.

2003-01-01

The surface of 310 stainless steel (310SS) samples was investigated by X-ray photoelectron spectroscopy (XPS) after 500 h cyclic exposure to two carburizing atmospheres: CH 4 (2%)-H 2 (98%) at 800 deg. C, and CH 4 (10%)-H 2 (90%) at 1100 deg. C. The depth distribution of various elements in the surface region was obtained by XPS after successive cycles of argon etching. The microstructure of the alloy was observed by scanning electron microscopy (SEM) and the phases formed during the exposure were analyzed by X-ray diffraction (XRD). The results showed that the major phases that were formed within few micrometer depth during exposure at 800 deg. C include both iron and chromium carbides. (Mn, Cr) oxide was also formed as a result of the reaction with the residual oxygen of the atmosphere. A region of few microns width that was relatively depleted of chromium was formed under the surface as a result of the outwards diffusion of chromium. The exposure to the reducing atmosphere at 1100 deg. C led to the formation of various iron and chromium carbides. No oxide was formed during exposure. In all exposed samples, the surface was Cr enriched while nickel remained buried under the surface region that reacted with the atmosphere

ANALYSE DES PERCEPTIONS LOCALES ET DES FACTEURS ...

African Journals Online (AJOL)

AISA

1Faculté des Sciences Agronomiques (FSA), Université d'Abomey-Calavi (UAC), 01 BP 526 Cotonou Bénin. Email : cgbemavo@yahoo.fr. 2Institut National des Recherches Agricoles du Bénin, Centre de Recherches Agricoles d'Agonkanmey (CRA-A),. Laboratoire des Sciences du Sol, Eau et Environnement (LSSEE).

Evaluation of crack growth behavior and probabilistic S–N characteristics of carburized Cr–Mn–Si steel with multiple failure modes

International Nuclear Information System (INIS)

Li, Wei; Sun, Zhenduo; Zhang, Zhenyu; Deng, Hailong; Sakai, Tatsuo

2014-01-01

Highlights: • The stepwise S–N characteristics only for interior induced failure was observed. • The interior crack growth behavior with threshold conditions in different stages was clarified. • The distribution characteristics of test data in transition failure region was evaluated. • A model for evaluating the probabilistic S–N curve with multiple failure modes was developed. - Abstract: The unexpected failures of case-hardened steels in long life regime have been a critical issue in modern engineering design. In this study, the failure behavior of a carburized Cr–Mn–Si steel under very high cycle fatigue (VHCF) was investigated, and a model for evaluating the probabilistic S–N curve associated with multiple failure modes was developed. Results show that the carburized Cr–Mn–Si steel exhibits three failure modes including the surface flaw-induced failure, the interior inclusion-induced failure without the fine granular area (FGA) and the interior inclusion-induced failure with the FGA. As the predominant failure mode in the VHCF regime, the interior failure process can be divided into four stages: (i) the small crack growth around the inclusion, (ii) the stable macroscopic crack growth outside the FGA, (iii) the unstable crack growth outside the fish-eye and (iv) the momentary fracture outside the final crack growth zone. The threshold values are successively evaluated to be 2.33 MPa m 1/2 , 4.13 MPa m 1/2 , 18.51 MPa m 1/2 and 29.26 MPa m 1/2 . The distribution characteristics of the test data in transition failure region can be well characterized by the mixed two-parameter Weibull distribution function. The developed probabilistic S–N curve model is in good agreement with the test data with multiple failure modes. Although the result is somewhat conservative in the VHCF regime, it is acceptable for safety considerations

Planck's constant and the three waves (TWs) of Einstein's covariant ether

Science.gov (United States)

Kostro, L.

1985-11-01

The implications of a three-wave model for elementary particles, satisfying the principles of both quantum mechanics and General Relativity (GR), are discussed. In GR, the ether is the fundamental source of all activity, where particles (waves) arise at singularities. Inertia and gravity are field properties of the ether. In flat regions of the space-time geodesic, wave excitations correspond to the presence of particles. A momentum-carrying excitation which occurs in the ether is a superluminal radiation (phase- or B-waves) which transports neither energy nor mass. Superposition of the B-waves produces soliton-like excitations on the ether to form C-waves, i.e., particles. The particle-waves travel through space-time on D-waves, and experience reflection, refraction and interference only where B-waves have interacted with the ether. The original particles, photons-maximons, existed at the Big Bang and had physical properties which are describable in terms of Planck's quantities.

Oil recovery with sulfomethylated poly (lower alkyl vinyl ether/maleic anhydride)

Energy Technology Data Exchange (ETDEWEB)

Norton, C.J.; Falk, D.O.

1973-05-22

Lower alkyl vinyl ether e.g., methyl vinyl ether, propyl vinyl ether, isopropyl vinyl ether, hexyl vinyl ether, is copolymerized conventionally with maleic anhydride, the resulting copolymer is treated with ammonia or ammonium hydroxide to form the partial amide-ammonium salt, and this salt is in turn treated with formaldehyde and thereafter or simultaneously with ammonium or alkali metal salt sulfite (including bisulfites, etc.) to form an at least partially sulfomethylated copolymer. Aqueous solutions of the sulfomethylated copolymer are useful in increasing the viscosity of drive fluids used in the supplemented recovery of petroleum from subterranean formations. In general, enhancing the polyionic character of mobility control agents used in supplemented recovery of petroleum provides enhanced recovery. Achieving this enhancement of polyionic character through use of sulfonate groups provides a mobility control agent with good ability to sustain viscosity in the presence of brine and lime, usually present in the connate waters of petroleum-bearing formations. (7 claims)

variabilite des productions et des revenus des exploitations

African Journals Online (AJOL)

3Centre de coopération internationale en recherche agronomique pour le développement (CIRAD), UMR Innovation,. Montpellier, France. Doubangolo COULIBALY, Email kone_b@yahoo.fr. RESUME. La durabilité des systèmes de production à base de coton dans un contexte de variabilité des prix aux producteurs et de ...

Le statut vitaminique des individus et des populations…

Directory of Open Access Journals (Sweden)

Icart Jean-Claude

2000-05-01

Full Text Available Comme le souligne un récent rapport du Haut comité de santé publique, le statut vitaminique des individus et des populations demeure une question d’actualité. Si les études ne révèlent plus de signes évocateurs de carence, au plus des problèmes de déficiences pour certains groupes à risque, des interrogations, demeurent malgré le contexte d’abondance, concernant la couverture des besoins, laquelle pourrait s’avérer inférieure aux valeurs considérées comme satisfaisantes.

Application des TIC à l'atténuation des effets des catastrophes dans ...

International Development Research Centre (IDRC) Digital Library (Canada)

L'Amérique centrale est souvent aux prises avec des inondations et des ... (SIG) et de traitement des images, afin de cartographier les dangers et de modéliser les ... de l'Institut d'étude du développement international de l'Université McGill.

An improved synthesis process of calixcrown ethers and synthesis of novel calixcrown ether

International Nuclear Information System (INIS)

Wang Hairong; Zhang Ping; Wang Chunmiao; Wang Jianchen; Chen Jing

2007-01-01

The synthesis method of calixcrown ethers was simplified and improved, and 10 L- scale synthesis was carried out. In the synthesis of the intermediates of the first three steps, the synthesis of 5, 11, 17, 23-tetra-tert-butyl-25, 26, 27, 28-tetrahydroxyl-calix[4] and its dehydroxylation were considered together, the purification procedures of the former, including re-crystallization in toluene and decolorization with activated carbon, were cancelled, and thus these steps were simplified. In the synthesis of oligoethylene glycol ditosylate, the purification method was also improved and the time-consuming column chromatography was left out. In the final step, impurities were removed by repeating stirring-settlement steps, by following recrystallization, the pure product was obtained. With these measures, the whole process could be implemented easily. The industrial scale production of calixcrown ethers could be fulfilled with the improved process. In addition, a new extracant, 25, 27-bis (n-propyloxy)calix[4]-26, 28-crown-6, is prepared and identified. (authors)

Investigation of ammonium trinitratouranylate complexing with diethyl ether

International Nuclear Information System (INIS)

Khod'ko, N.N.; Kolevich, T.A.; Umrejko, D.S.

1989-01-01

Interaction of ammonium trinitratouranylate (ATNU) with diethyl ether is investigated. It is shown, that adduct of UO 2 (NO 3 ) 2 · 2(C 2 H 5 ) 2 O coposition is formed in the indicated solvent due to incongruent solubility of ANTU. Analogous compound is obtained at ether effect on uranyl anhydrous nitrate. The matter is determined and investigated by means of chemical, thermal analyses and oscillating spectroscopy

La gestion des résultats des entreprises innovantes

OpenAIRE

Dumas, Guillaume

2014-01-01

Cette thèse s’intéresse à la gestion des résultats dans le cadre des entreprises innovantes. Elle est constituée de trois articles. Dans le premier, il s’agit d’examiner si les résultats des entreprises innovantes sont gérés et si le stade de développement des innovations influence cette gestion des résultats. Il apparaît que les résultats des entreprises innovantes sont gérés à la hausse. Cette gestion ne semble intervenir qu’au cours de l’activité d’innovation (c’est-à-dire lorsque les entr...

Etude des erreurs d'estimation des populations par la méthode des captures successives (DeLURY, 2 captures et des captures-recaptures (PETERSEN

Directory of Open Access Journals (Sweden)

LAURENT M.

1978-01-01

Full Text Available L'estimation des populations naturelles par capture-recapture et par captures successives est souvent entachée d'erreur car, dans de nombreux cas, l'hypothèse fondamentale d'égalité des probabilités de captures pour tous les individus dans le temps et dans l'espace n'est pas respectée. Dans le cas des populations de poissons envisagés ici, les captures ont lieu par la pêche électrique. On a pu chiffrer l'ordre de grandeur des erreurs systématiques faites sur l'estimation des peuplements, en fonction des conditions particulières, biotiques et abiotiques, des différents milieux inventoriés.

Metal ion separations with proton-ionizable Lariat Ethers and their polymers

International Nuclear Information System (INIS)

Bartsch, R.A.

1993-01-01

The preparation of novel and specific organic complexing agents may lead to the development of new separation systems for aqueous metal ions. Thus the introduction of highly lipophilic oximes led to the current utilization of these compounds as commercial extractants for the hydrometallurgy of nonferrous metals. Crown ethers (macrocyclic polyethers) have been employed in the laboratory-scale solvent extraction of alkali-metal, alkaline-earth, and other metal cations into organic phases. Attachment of side arms to crown ethers gives lariat ethers. The presence of one or more potential coordination sites in the side arm of the lariat ether may produce substantial changes in the selectivity and efficiency of metal ion complexation. It has been demonstrated that concomitant transfer of an aqueous phase anion into the organic medium is not required for metal ion extraction. This factor is of immense importance to potential practical applications of these proton-ionizable crown ethers in which the common, hard, aqueous phase anions would be involved. Another advantage of proton-ionizable lariat ethers is the ease with which extracted metal ions may be stripped from the organic phase by shaking with aqueous mineral acid. Thus both metal ion extraction and stripping are facilitated by pendent proton-ionizable groups. Most of the hazardous metal ion species in the Hanford Site tank wastes are members of the alkali-metal, alkaline-earth, lanthanide, and actinide families. These hard metal ion species prefer association with hard donor atoms, such as oxygens. Therefore, crown and lariat ethers are well-suited for complexation with such metal ion species

Spontaneous Generation of Chirality in Simple Diaryl Ethers.

Science.gov (United States)

Lennartson, Anders; Hedström, Anna; Håkansson, Mikael

2015-07-01

We studied the spontaneous formation of chiral crystals of four diaryl ethers, 3-phenoxybenzaldehyde, 1; 1,3-dimethyl-2-phenoxybenzene, 2; di(4-aminophenyl) ether, 3; and di(p-tolyl) ether, 4. Compounds 1, 3, and 4 form conformationally chiral molecules in the solid state, while the chirality of 2 arises from the formation of supramolecular helices. Compound 1 is a liquid at ambient temperature, but 2-4 are crystalline, and solid-state CD-spectroscopy showed that they could be obtained as optically active bulk samples. It should be noted that the optical activity arise upon crystallization, and no optically active precursors were used. Indeed, even commercial samples of 3 and 4 were found to be optically active, giving evidence for the ease at which total spontaneous resolution may occur in certain systems. © 2015 Wiley Periodicals, Inc.

Enhanced response of microbial fuel cell using sulfonated poly ether ether ketone membrane as a biochemical oxygen demand sensor

Energy Technology Data Exchange (ETDEWEB)

Ayyaru, Sivasankaran; Dharmalingam, Sangeetha, E-mail: sangeetha@annauniv.edu

2014-03-01

Graphical abstract: - Highlights: • Sulfonated poly ether ether ketone (SPEEK) membrane in SCMFC used to determine the BOD. • The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm. • This sensing range was 62.5% higher than that of Nafion{sup ®}. • SPEEK exhibited one order lesser oxygen permeability than Nafion{sup ®}. • Nafion{sup ®} shows high anodic internal resistance (67 Ω) than the SPEEK (39 Ω). - Abstract: The present study is focused on the development of single chamber microbial fuel cell (SCMFC) using sulfonated poly ether ether ketone (SPEEK) membrane to determine the biochemical oxygen demand (BOD) matter present in artificial wastewater (AW). The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm when using artificial wastewater. This sensing range was 62.5% higher than that of Nafion{sup ®}. The most serious problem in using MFC as a BOD sensor is the oxygen diffusion into the anode compartment, which consumes electrons in the anode compartment, thereby reducing the coulomb yield and reducing the electrical signal from the MFC. SPEEK exhibited one order lesser oxygen permeability than Nafion{sup ®}, resulting in low internal resistance and substrate loss, thus improving the sensing range of BOD. The system was further improved by making a double membrane electrode assembly (MEA) with an increased electrode surface area which provide high surface area for electrically active bacteria.

Injectabilite des coulis de ciment dans des milieux fissures

Science.gov (United States)

Mnif, Thameur

Le travail presente ici est un bilan du travaux de recherche effectues sur l'injectabilite des coulis de ciment dans lu milieux fissures. Un certain nombre de coulis a base de ciment Portland et microfin ont ete selectionnes afin de caracteriser leur capacite a penetrer des milieux fissures. Une partie des essais a ete menee en laboratoire. L'etude rheologique des differents melanges a permis de tester l'influence de l'ajout de superplastifiant et/ou de fumee de silice sur la distribution granulometrique des coulis et par consequent sur leur capacite a injecter des colonnes de sable simulant un milieu fissure donne. La classe granulometrique d'un coulis, sa stabilite et sa fluidite sont apparus comme les trois facteurs principaux pour la reussite d'une injection. Un facteur de finesse a ete defini au cours de cette etude: base sur la classe granulometrique du ciment et sa stabilite, il peut entrer dans la formulation theorique du debit d'injection avant application sur chantier. La deuxieme et derniere partie de l'etude presente les resultats de deux projets de recherche sur l'injection realises sur chantier. L'injection de dalles de beton fissurees a permis le suivi de l'evolution des pressions avec la distance au point d'injection. L'injection de murs de maconnerie a caractere historique a montre l'importance de la definition de criteres de performance des coulis a utiliser pour traiter un milieu donne et pour un objectif donne. Plusieurs melanges peuvent ainsi etre predefinis et mis a disposition sur le chantier. La complementarite des ciments traditionnels et des ciments microfins devient alors un atout important. Le choix d'utilisation de ces melanges est fonction du terrain rencontre. En conclusion, cette recherche etablit une methodologie pour la selection des coulis a base de ciment et des pressions d'injection en fonction de l'ouverture des fissures ou joints de construction.

Poly (ether ether ketone) derivatives: Synthetic route and characterization of nitrated and sulfonated polymers

International Nuclear Information System (INIS)

Conceicao, T.F.; Bertolino, J.R.; Barra, G.M.O.; Pires, A.T.N.

2009-01-01

Nitrated and sulfonated poly (ether ether ketone) [SNPEEK] samples were prepared through sulfonation of nitrated PEEK (NPEEK) at different temperatures resulting in polymers with distinct sulfonation degrees (SD). The sulfonation occurred preferentially in the hydroquinone segment even after 81% of this moiety had been nitrated. Sulfonation in the benzophenone moiety was achieved only in 16% of this segment at the reaction temperature of 80 deg. C. The substitution degree was obtained through the TG curves, and values were in agreement with 1 H NMR data when SD is much higher as ND (nitration degree). The highest SD obtained was 72%. Membranes of the sulfonated and nitrated PEEK (SNPEEK) were prepared by casting and showed good ductility depending on the substitution degree, with proton conductivity in the order of 10 -2 S cm -1 , an important characteristic in some applications, such as in fuel cells

Poly (ether ether ketone) derivatives: Synthetic route and characterization of nitrated and sulfonated polymers

Energy Technology Data Exchange (ETDEWEB)

Conceicao, T.F.; Bertolino, J.R. [Grupo de Estudo em Materiais Polimericos-Departamento de Quimica, Universidade Federal de Santa Catarina, Florianopolis, SC (Brazil); Barra, G.M.O. [Departamento de Engenharia Mecanica, Universidade Federal de Santa Catarina, Florianopolis, SC (Brazil); Pires, A.T.N. [Grupo de Estudo em Materiais Polimericos-Departamento de Quimica, Universidade Federal de Santa Catarina, Florianopolis, SC (Brazil)], E-mail: alfredotiburcio@pq.cnpq.br

2009-03-01

Nitrated and sulfonated poly (ether ether ketone) [SNPEEK] samples were prepared through sulfonation of nitrated PEEK (NPEEK) at different temperatures resulting in polymers with distinct sulfonation degrees (SD). The sulfonation occurred preferentially in the hydroquinone segment even after 81% of this moiety had been nitrated. Sulfonation in the benzophenone moiety was achieved only in 16% of this segment at the reaction temperature of 80 deg. C. The substitution degree was obtained through the TG curves, and values were in agreement with {sup 1}H NMR data when SD is much higher as ND (nitration degree). The highest SD obtained was 72%. Membranes of the sulfonated and nitrated PEEK (SNPEEK) were prepared by casting and showed good ductility depending on the substitution degree, with proton conductivity in the order of 10{sup -2} S cm{sup -1}, an important characteristic in some applications, such as in fuel cells.

La gouvernance des risques naturels et la problematique des ...

African Journals Online (AJOL)

Depuis quelques années, la gouvernance des risques naturels dus aux inondations remet en cause les processus de mise en oeuvre des politiques urbaines et la qualité de la structure des aménagements dans les grandes villes du Golfe de Guinée. La perception de la gouvernance et l'application des politiques de ...

Interpolymer complexses of vinyl ether copolymer with polyacrylic and polymethacrylic acids

Directory of Open Access Journals (Sweden)

E. Shaikhutdinov

2012-03-01

Full Text Available The interactions between macromolecules of copolymers based on vinyl ethers (vinyl ether of monoethanolamine and vinyl buthyl ether and 2-acryloilamido-2-methylpropanesulphonic acid with polyacrylic and polymethacrylic acid and, as well as study the effect of interpolymer interactions in the adsorption of polymers at the aqueous solution-air interface were investigated. The observed synergistic increase in surface activity of macromolecules into polyelectrolyte mixtures explained by the formation of interpolymer complexes polyacid - copolymer.

Absorption of decabromodiphenyl ether and other organohalogen chemicals by grey seals (Halichoerus grypus)

International Nuclear Information System (INIS)

Thomas, Gareth O.; Moss, Simon E.W.; Asplund, Lillemor; Hall, Ailsa J.

2005-01-01

An input-output balance study was performed for polybrominated diphenyl ethers, polychlorinated biphenyls and some organochlorine pesticides on three captive, juvenile grey seals (Halichoerus grypus). The animals were fed a diet of herring for six months, during the last three months of which this study was performed. A supplement of decabromodiphenyl ether was included in the diet during the second month of the study. Consistently high absorption (>89%) was observed for all of the chemicals studied, whereas work on other animals has generally shown high (>80%) net absorption at log K OW OW , and very low absorption of decabromodiphenyl ether. The half-life of decabromodiphenyl ether in blood was estimated to be between 8.5 and 13 days. Measurable concentrations of decabromodiphenyl ether were detected in seal blubber at the end of the study, indicating that this chemical can be stored in adipose and may bioaccumulate. Current understanding of the mechanism of absorption of organohalogen chemicals and the potential for accumulation of decabromodiphenyl ether will need reassessing in the light of these results. - Decabromodiphenyl ether is absorbed effectively from the diet by grey seals, and can be stored in the blubber even after exposure ceases

Carburization behavior under the pits induced by metal dusting in 304L and 347 stainless steels

Energy Technology Data Exchange (ETDEWEB)

Chang, Chia-Hao [Department of Materials Engineering and Science, National Cheng Kung University, Tainan 701, Taiwan (China); Tsai, Wen-Ta, E-mail: wttsai@mail.ncku.edu.tw [Department of Materials Engineering and Science, National Cheng Kung University, Tainan 701, Taiwan (China)

2009-08-15

The metal dusting behavior of Type 304L and 347 stainless steels (SSs) in a flowing mixed CO/H{sub 2}/H{sub 2}O gas stream at 600 deg. C was investigated. After exposure in a 35% CO + 60% H{sub 2} + 5% H{sub 2}O gas for 500 h, large pits were formed on both steel surfaces. The aspect ratio of the pits formed in 304L SS was higher than that of the pits formed in 347 SS. The microstructures and chemical compositions of the reaction products and those of the substrate under the pits were examined by using a scanning electron microscope (SEM) combined with an energy dispersive spectrometer (EDS). A Cr-depleted zone containing voids was formed on the outer surface just beneath the pit. Massive matrix carburization and intergranular carbide precipitation were seen for both steels. The experimental results showed that niobium (Nb) could delay the ingress of carbon and retard the metal dusting reaction.

Process for producing high purity isoolefins and dimers thereof by dissociation of ethers

Science.gov (United States)

Smith, L.A. Jr.; Jones, E.M. Jr.; Hearn, D.

1984-05-08

Alkyl tertiary butyl ether or alkyl tertiary amyl ether is dissociated by vapor phase contact with a cation acidic exchange resin at temperatures in the range of 150 to 250 F at LHSV of 0.1 to 20 to produce a stream consisting of unreacted ether, isobutene or isoamylene and an alcohol corresponding to the alkyl radical. After the alcohol is removed, the ether/isoolefin stream may be fractionated to obtain a high purity isoolefin (99+%) or the ether/isoolefin stream can be contacted in liquid phase with a cation acidic exchange resin to selectively dimerize the isoolefin in a highly exothermic reaction, followed by fractionation of the dimerization product to produce high purity diisoolefin (97+%). In the case where the alkyl is C[sub 3] to C[sub 6] and the corresponding alcohol is produced on dissociation of the ether, combined dissociation-distillation may be carried out such that isoolefin is the overhead product and alcohol the bottom. 2 figs.

Nikola Tesla, the Ether and his Telautomaton

Science.gov (United States)

Milar, Kendall

2014-03-01

In the nineteenth century physicists' understanding of the ether changed dramatically. New developments in thermodynamics, energy physics, and electricity and magnetism dictated new properties of the ether. These have traditionally been examined from the perspective of the scientists re-conceptualizing the ether. However Nikola Tesla, a prolific inventor and writer, presents a different picture of nineteenth century physics. Alongside the displays that showcased his inventions he presented alternative interpretations of physical, physiological and even psychical research. This is particularly evident in his telautomaton, a radio remote controlled boat. This invention and Tesla's descriptions of it showcase some of his novel interpretations of physical theories. He offered a perspective on nineteenth century physics that focused on practical application instead of experiment. Sometimes the understanding of physical theories that Tesla reached was counterproductive to his own inventive work; other times he offered new insights. Tesla's utilitarian interpretation of physical theories suggests a more scientifically curious and invested inventor than previously described and a connection between the scientific and inventive communities.

Effect of ethylene glycol monomethyl ether and diethylene glycol monomethyl ether on hepatic metabolizing enzymes.

Science.gov (United States)

Kawamoto, T; Matsuno, K; Kayama, F; Hirai, M; Arashidani, K; Yoshikawa, M; Kodama, Y

1990-06-01

Glycol ethers have been extensively used in industry over the past 40-50 years. Numerous studies on the toxicity of glycol ethers have been performed, however, the effects of glycol ethers on the hepatic drug metabolizing enzymes are still unknown. We studied the changes of the putative metabolic enzymes, that is, the hepatic microsomal mixed function oxidase system and cytosolic alcohol dehydrogenase, by the oral administration of diEGME and EGME. Adult male Wistar rats were used. DiEGME was administered orally; 500, 1000, 2000 mg/kg for 1, 2, 5 or 20 days and EGME was 100, 300 mg/kg for 1, 2, 5 or 20 days. Decreases in liver weights were produced by highest doses of diEGME (2000 mg/kg body wt/day for 20 days) and EGME (300 mg/kg body wt/day for 20 days). DiEGME increased hepatic microsomal protein contents and induced cytochrome P-450, but not cytochrome b5 or NADPH-cytochrome c reductase. The activity of cytosolic ADH was not affected by diEGME administration. On the other hand, EGME did not change cytochrome P-450, cytochrome b5 or NADPH-cytochrome c reductase. The activity of cytosolic ADH was increased by repeated EGME treatment. Therefore it is suspected that the enzyme which takes part in the metabolism of diEGME is different from that of EGME, although diEGME is a structural homologue of EGME.

The preparation and intramolecular radical cyclisation reactions of chiral oxyme ethers

International Nuclear Information System (INIS)

Booth, Susan E.; Jenkins, Paul R.

1998-01-01

Chiral oxime ether 2 and Oxime ester 4 have been prepared by alkylation and esterification of the oxime 1. Racemic hydroxylamine 6 and chiral hydroxylamine 10 have been synthesised from N-hydroxysuccinimide and the corresponding alcohol in the presence of diethyl azo dicarboxylate, the two product were converted into the oxime ethers 7 and 11 respectively. The intramolecular radical cyclisation reactions of these oxime ethers and esters has been studied, successful reaction was observed to produce alkyl hydroxylamines 3,8 and 12. (author)

The Preparation and Intramolecular Radical Cyclisation Reactions of Chiral Oxime Ethers

Directory of Open Access Journals (Sweden)

Booth Susan E.

1998-01-01

Full Text Available Chiral oxime ether 2 and Oxime ester 4 have been prepared by alkylation and esterification of the oxime 1. Racemic hydroxylamine 6 and chiral hydroxylamine 10 have been synthesised from N-hydroxysuccinimide and the corresponding alcohol in the presence of diethylazodicarboxylate, the two products were converted into the oxime ethers 7 and 11 respectively. The intramolecular radical cyclisation reactions of these oxime ethers and esters has been studied, successful reaction was observed to produce alkyl hydroxylamines 3, 8 and 12.

Enzymatic network for production of ether amines from alcohols

DEFF Research Database (Denmark)

Palacio, Cyntia M.; Crismaru, Ciprian G.; Bartsch, Sebastian

2016-01-01

We constructed an enzymatic network composed of three different enzymes for the synthesis of valuable ether amines. The enzymatic reactions are interconnected to catalyze the oxidation and subsequent transamination of the substrate and to provide cofactor recycling. This allows production...... of the desired ether amines from the corresponding ether alcohols with inorganic ammonium as the only additional substrate. To examine conversion, individual and overall reaction equilibria were established. Using these data, it was found that the experimentally observed conversions of up to 60% observed...... for reactions containing 10mM alcohol and up to 280mM ammonia corresponded well to predicted conversions. The results indicate that efficient amination can be driven by high concentrations of ammonia and may require improving enzyme robustness for scale-up....

Basic randomness of nature and ether-drift experiments

International Nuclear Information System (INIS)

Consoli, M.; Pluchino, A.; Rapisarda, A.

2011-01-01

Highlights: ► We re-consider the idea of a basic randomness of nature. ► We adopt Stochastic Electro Dynamics as a heuristic model. ► We represent the vacuum as a form of turbulent ether. ► This picture can be tested with forthcoming ether-drift experiments. - Abstract: We re-consider the idea that quantum fluctuations might reflect the existence of an ‘objective randomness’, i.e. a basic property of the vacuum state which is independent of any experimental accuracy of the observations or limited knowledge of initial conditions. Besides being responsible for the observed quantum behavior, this might introduce a weak, residual form of ‘noise’ which is intrinsic to natural phenomena and could be important for the emergence of complexity at higher physical levels. By adopting Stochastic Electro Dynamics as a heuristic model, we are driven to a picture of the vacuum as a form of highly turbulent ether, which is deep-rooted into the basic foundational aspects of both quantum physics and relativity, and to search for experimental tests of this scenario. An analysis of the most precise ether-drift experiments, operating both at room temperature and in the cryogenic regime, shows that, at present, there is some ambiguity in the interpretation of the data. In fact the average amplitude of the signal has precisely the magnitude expected, in a ‘Lorentzian’ form of relativity, from an underlying stochastic ether and, as such, might not be a spurious instrumental effect. This puzzle, however, should be solved in a next future with the use of new cryogenically cooled optical resonators whose stability should improve by about two orders of magnitude. In these new experimental conditions, the persistence of the present amplitude would represent a clean evidence for the type of random vacuum we are envisaging.

Enhanced osteogenic activity of poly ether ether ketone using calcium plasma immersion ion implantation.

Science.gov (United States)

Lu, Tao; Qian, Shi; Meng, Fanhao; Ning, Congqin; Liu, Xuanyong

2016-06-01

As a promising implantable material, poly ether ether ketone (PEEK) possesses similar elastic modulus to that of cortical bones yet suffers from bio-inertness and poor osteogenic properties, which limits its application as orthopedic implants. In this work, calcium is introduced onto PEEK surface using calcium plasma immersion ion implantation (Ca-PIII). The results obtained from scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) confirm the modified layer with varying contents of calcium are formed on PEEK surfaces. Water contact angle measurements reveal the increasing hydrophobicity of both Ca-PIII treated surfaces. In vitro cell adhesion, viability assay, alkaline phosphatase activity and collagen secretion analyses disclose improved the adhesion, proliferation, and osteo-differentiation of rat bone mesenchymal stem cells (bMSCs) on Ca-PIII treated surfaces. The obtained results indicate that PEEK surface with enhanced osteogenic activity can be produced by calcium incorporation. Copyright © 2016 Elsevier B.V. All rights reserved.

Promouvoir l'entrepreneuriat inclusif des jeunes et des femmes ...

International Development Research Centre (IDRC) Digital Library (Canada)

Le projet vise à analyser la contribution réelle et potentielle de l'entrepreneuriat inclusif au bien-être des jeunes et des femmes en Côte d'Ivoire, au Burkina Faso et au Kenya. Après un état des lieux de la pratique de l'entrepreneuriat inclusif dans chacun des pays ciblés, l'équipe de recherche étudiera son incidence sur ...

Gold-catalyzed alkylation of silyl enol ethers with ortho-alkynylbenzoic acid esters

Directory of Open Access Journals (Sweden)

Yoshinori Yamamoto

2011-05-01

Full Text Available Unprecedented alkylation of silyl enol ethers has been developed by the use of ortho-alkynylbenzoic acid alkyl esters as alkylating agents in the presence of a gold catalyst. The reaction probably proceeds through the gold-induced in situ construction of leaving groups and subsequent nucleophilic attack on the silyl enol ethers. The generated leaving compound abstracts a proton to regenerate the silyl enol ether structure.

Structuring of poly ether ether ketone by ArF excimer laser radiation in different atmospheres

International Nuclear Information System (INIS)

Feng, Y.; Gottmann, J.; Kreutz, E.W.

2003-01-01

Structuring of poly ether ether ketone (PEEK) by 193 nm ArF excimer laser radiation has been investigated. Experiments were carried out in different atmospheres (air, vacuum, Ar, O 2 ) in order to study its influence on the quality of the structures and the formation of the debris. Repetition rate makes little effect on the ablation rate and roughness of the structure in presence of any kind of atmosphere, indicating for the structuring of PEEK by ArF laser radiation a large window of processing. The roughness at the bottom of the structures and the morphology of the side walls are strongly affected by the properties of the atmosphere. The smallest roughness is achieved at 0.6 J/cm 2 for all kinds of processing gases. Debris around the structures can be diminished by structuring in vacuum. Plasma expansion speed has been measured by using high speed photography

Prise en charge des urgences au service d'accueil des urgences ...

African Journals Online (AJOL)

Introduction: La prise en charge des patients dans les services d'accueil des urgences est une des meilleures vitrines d'un système de santé. En Afrique subsaharienne, la gestion des urgences se heurte à des difficultés humaines et matérielles. Le but de ce travail était d'évaluer les difficultés de prise en charge au Service ...

The influence of water mixtures on the dermal absorption of glycol ethers

International Nuclear Information System (INIS)

Traynor, Matthew J.; Wilkinson, Simon C.; Williams, Faith M.

2007-01-01

Glycol ethers are solvents widely used alone and as mixtures in industrial and household products. Some glycol ethers have been shown to have a range of toxic effects in humans following absorption and metabolism to their aldehyde and acid metabolites. This study assessed the influence of water mixtures on the dermal absorption of butoxyethanol and ethoxyethanol in vitro through human skin. Butoxyethanol penetrated human skin up to sixfold more rapidly from aqueous solution (50%, 450 mg/ml) than from the neat solvent. Similarly penetration of ethoxyethanol was increased threefold in the presence of water (50%, 697 mg/ml). There was a corresponding increase in apparent permeability coefficient as the glycol ether concentration in water decreased. The maximum penetration rate of water also increased in the presence of both glycol ethers. Absorption through a synthetic membrane obeyed Fick's Law and absorption through rat skin showed a similar profile to human skin but with a lesser effect. The mechanisms for this phenomenon involves disruption of the stratum corneum lipid bilayer by desiccation by neat glycol ether micelles, hydration with water mixtures and the physicochemical properties of the glycol ether-water mixtures. Full elucidation of the profile of absorption of glycol ethers from mixtures is required for risk assessment of dermal exposure. This work supports the view that risk assessments for dermal contact scenarios should ideally be based on absorption data obtained for the relevant formulation or mixture and exposure scenario and that absorption derived from permeability coefficients may be inappropriate for water-miscible solvents

A mild and efficient procedure for the synthesis of ethers from various alkyl halides

Directory of Open Access Journals (Sweden)

Mosstafa Kazemi

2013-10-01

Full Text Available A simple, mild and practical procedure has been developed for the synthesis of symmetrical and unsymmetrical ethers by using DMSO, TBAI in the presence of K2CO3. We extended the utility of Potassium carbonate as an efficient base for the preparation of ethers. A wide range of alkyl aryl and dialkyl ethers are synthezied from treatment of aliphatic alcohols and phenols with various alkyl halides in the prescence of efficient base Potassium carbonate. Secondary alkyl halides were easily converted to corresponding ethers in releatively good yields . This is a mild, simple and practical procedure for the preparation of ethers in high yields and suitable times under mild condition.

Induced production of halogenated diphenyl ethers from the marine-derived fungus Penicillium chrysogenum.

Science.gov (United States)

Yang, Guohua; Yun, Keumja; Nenkep, Viviane N; Choi, Hong Dae; Kang, Jung Sook; Son, Byeng Wha

2010-11-01

Manipulation of the fermentation of the marine-derived fungus Penicillium chrysogenum by addition of CaBr(2) resulted in induced production of bromodiphenyl ether analogs. Two new free-radical-scavenging polybrominated diphenyl ethers, 1 and 2, and three known diphenyl ethers, 3,3'-dihydroxy-5,5'-dimethyldiphenyl ether (3), and an inseparable mixture of violacerol-I (4) and violacerol-II (5) were isolated. The structures of the two new polybromodiphenyl ethers 1 and 2 were assigned by combined spectroscopic-data analysis, including deuterium-induced isotope effect. Compounds 1-3, and a mixture of 4 and 5 exhibited radical-scavenging activities against 1,1-diphenyl-2-picrylhydrazyl with IC(50) values of 18, 15, 42, and 6 μM, respectively. With the exception of 3, the compounds were, therefore, more active than the positive control, ascorbic acid (IC(50) 20 μM).

Connaissances, attitudes et pratiques des prestataires de santé des ...

African Journals Online (AJOL)

... des prestataires interrogés avaient respectivement une bonne connaissance des facteurs de risque et des moyens de dépistage. Les signes évocateurs et les examens complémentaires nécessaires au diagnostic du cancer du sein étaient connus par 15,3 % des prestataires. La définition du cancer du sein et les moyens ...

Acidolysis small molecular phenolic ether used as accelerator in photosensitive diazonaphthaquinone systems

Science.gov (United States)

Zhou, Haihua; Zou, Yingquan

2006-03-01

The photosensitive compounds in the photosensitive coatings of positive PS plates are the diazonaphthaquinone derivatives. Some acidolysis small molecular phenolic ethers, which were synthesized by some special polyhydroxyl phenols with vinyl ethyl ether, are added in the positive diazonaphthaquinone photosensitive composition to improve its sensitivity, composed with photo-acid-generators. The effects to the photosensitivity, anti-alkali property, anti-isopropyl alcohol property, dot resolution and line resolution of the coatings are studied with different additive percent of the special phenolic ethers. In the conventional photosensitive diazonaphthaquinone systems for positive PS plates, the photosensitivity is improved without negative effects to resolution, anti-alkali and anti-isopropyl alcohol properties when added about 5% of the special acidolysis phenolic ethers, EAAE or DPHE, composed with photo-acid-generators.

The simple ethers of glycerin

International Nuclear Information System (INIS)

Kimsanov, B.Kh.; Karimov, M.B.

1998-01-01

From glycerin derivatives the considerable interest is present simple ethers because many of them are biological active and found wide practical using as an effect drugs, inters for thin organic synthesis, vehicle for injections, regulators of plants growth, reagents, components for perfumery-cosmetic goods and etc

The PROMETHEE multiple criteria decision making analysis for selecting the best membrane prepared from sulfonated poly(ether ketone)s and poly(ether sulfone)s for proton exchange membrane fuel cell

International Nuclear Information System (INIS)

Nikouei, Mohammad Ali; Oroujzadeh, Maryam; Mehdipour-Ataei, Shahram

2017-01-01

Proton exchange membrane as the heart of fuel cell has been the topic of many research activities in recent years. Finding a suitable alternative for Nafion membranes is one of the most important issues of interest. This study is dedicated to sulfonated poly(ether ketone) and poly(ether sulfone) membranes. For synthesis of these two groups of polymers, two different isomeric biphenols (meta- and para-) were used and each group of membranes with three different degree of sulfonation (25, 35, and 45%) was synthesized. In this way, twelve different membrane samples were obtained and their properties were evaluated. Since each membrane had some strong and some weak points of properties in comparison to the other ones, using a rational analysis for choosing the best membrane between prepared samples was inevitable. For this purpose a PROMETHEE based multiple criteria decision making approach was applied and for evaluation of the weight of each criterion, Shannon entropy method was used. Final results showed that poly(ether ketone) membranes in selected criteria were better than poly(ether sulfone) membranes and as expected, membranes with the highest degree of sulfonation (45%) were placed at the top ranking levels. - Highlights: • Sulfonated poly(ether ketone)s and Poly(ether sulfone)s were synthesized. • Related membranes for PEMFC were prepared. • The properties of membranes were measured. • Multiple criteria decision making approach was used to ranking the membranes. • PROMETHEE based approach selected poly(ether ketone)s as better choices.

Preparation of poly(ether ether ketone)-based polymer electrolytes for fuel cell membranes using grafting technique

International Nuclear Information System (INIS)

Hasegawa, Shin; Suzuki, Yasuyuki; Maekawa, Yasunari

2008-01-01

Poly(ether ether ketone) (PEEK)-based polymer electrolyte membranes (PEMs) was successfully prepared by radiation grafting of a styrene monomer into PEEK films and the consequent selective sulfonation of the grafting chains in the film state. Using milder sulfonation, the sulfonation reactions proceeded at the grafted chains in preference to the phenylene rings of PEEK main chains; as a result, the grafted films could successfully transform to a PEM with conductivity of more than 0.1 S/cm. The ion exchange capacity (IEC) and conductivity of the grafted PEEK electrolyte membranes were controlled to the ranges of 1.2-2.9 mmol/g and 0.03-0.18 S/cm by changing the grafting degree. It should be noted that this is the first example of directly transforming super-engineering plastic films into a PEM using radiation grafting

Sulfonated Poly(Ether Ether Ketone)/Functionalized Carbon Nanotube Composite Membrane for Vanadium Redox Flow Battery Applications

International Nuclear Information System (INIS)

Jia, Chuankun; Cheng, Yuanhang; Ling, Xiao; Wei, Guanjie; Liu, Jianguo; Yan, Chuanwei

2015-01-01

A novel sulfonated poly(ether ether ketone) (SPEEK) membrane embedded with the short-carboxylic multi-walled carbon nanotube (we name it as SPEEK/SCCT membrane) for vanadium redox flow battery (VRB) has been prepared with low capacity loss, low cost and high energy efficiency. The mechanical strength, vanadium ions permeability and performance of the membrane in the VRB single cell were characterized. Results showed that the SPEEK/SCCT membrane possessed low permeability of vanadium ions, accompanied by higher mechanical strength than the Nafion 212 membrane. The VRB single cell with SPEEK/SCCT membrane showed 7% higher coulombic efficiency (CE), 6% higher energy efficiency (EE) but lower capacity loss in comparison with the one with Nafion 212. The good cell performance, low capacity loss and high vanadium ions barrier properties of the blend membrane is of significant interest for VRB applications

Influence of structure of crown ethers on their radiation stability

International Nuclear Information System (INIS)

Grigor'ev, E.I.; Myasoedova, T.G.; Nesterov, S.V.; Trakhtenberg, L.I.

1988-01-01

Primary products of γ-radiolysis of crown ethers with the same size of the macrocyclic ring and different substituents were studied by EPR and mass spectrometry. It was shown that introduction of substituents into the polyether ring increases the radiation stability of crown ethers due to intramolecular transfer of energy from the polyether ring to a substituent

Hydrogenation-disproportionation-desorption-recombination in Sm2Fe16M (M=Al, Ga and Si) and magnetic properties of their carburized powders

International Nuclear Information System (INIS)

Kubis, M.; Rave, W.; Cao, L.; Gebel, B.; Mueller, K.-H.; Schultz, L.

1998-01-01

The application of the hydrogenation-disproportionation-desorption-recombination (HDDR) process in Sm 2 Fe 16 M (M=Al,Ga and Si) was investigated. The hydrogen absorption behaviour was studied by temperature-pressure analysis (TPA). In the temperature range between 500 and 800 C, Sm 2 Fe 16 M samples with M=Ga and Si show a weaker hydrogen absorption than Sm 2 Fe 16 Al. This was confirmed by X-ray diffraction which showed a complete disproportionation of Sm 2 Fe 16 Al into SmH z (1.9 2 Fe 16 Ga and Sm 2 Fe 16 Si exhibit a fraction of undecomposed material with the Th 2 Zn 17 -type structure after the disproportionation procedure. These results point to a stabilization of Sm 2 Fe 16 M against disproportionation by hydrogen for M=Ga and Si. The magnetization processes of carburized HDDR powders were studied by VSM measurements and Kerr microscopy. The demagnetization curve of our HDDR processed Sm 2 Fe 16 AlC y is well shaped, whereas those of Sm 2 Fe 16 GaC y and Sm 2 Fe 16 SiC y show a large decrease of the polarization at low fields. The favourable behaviour of Sm 2 Fe 16 AlC y is due to a homogeneous submicron grain structure. In Sm 2 Fe 16 GaC y and Sm 2 Fe 16 SiC y samples, an additional, magnetically soft phase with larger domains was observed which causes the low coercivity. As a consequence, HDDR was only favourable for the preparation of Sm 2 Fe 16 MC y hard magnets with M=Al but not for M=Ga and Si. Optimization of the HDDR process in Sm 2 Fe 16 Al and subsequent nitrogenation or carburization led to coercivities of μ 0j H c =2.9 and 2.5 T, respectively. (orig.)

Degradation of Perfluorinated Ether Lubricants on Pure Aluminum Surfaces: Semiempirical Quantum Chemical Modeling

Science.gov (United States)

Slaby, Scott M.; Ewing, David W.; Zehe, Michael J.

1997-01-01

The AM1 semiempirical quantum chemical method was used to model the interaction of perfluoroethers with aluminum surfaces. Perfluorodimethoxymethane and perfluorodimethyl ether were studied interacting with aluminum surfaces, which were modeled by a five-atom cluster and a nine-atom cluster. Interactions were studied for edge (high index) sites and top (low index) sites of the clusters. Both dissociative binding and nondissociative binding were found, with dissociative binding being stronger. The two different ethers bound and dissociated on the clusters in different ways: perfluorodimethoxymethane through its oxygen atoms, but perfluorodimethyl ether through its fluorine atoms. The acetal linkage of perfluorodimeth-oxymethane was the key structural feature of this molecule in its binding and dissociation on the aluminum surface models. The high-index sites of the clusters caused the dissociation of both ethers. These results are consistent with the experimental observation that perfluorinated ethers decompose in contact with sputtered aluminum surfaces.

Usages des TIC et socialisation professionnelle des enseignants-chercheurs

OpenAIRE

Lavielle-Gutnik, Nathalie; Massou, Luc

2013-01-01

En prenant appui sur une nouvelle analyse des données recueillies dans l’enquête Tec-Meus (2008-2011, MSH Lorraine) sur la place accordée par des enseignants-chercheurs en sciences humaines et sociales aux technologies de l’information et de la communication (TIC) dans leur activité d’enseignement, nous souhaitons nous focaliser dans cet article sur la compréhension des processus de socialisation professionnelle en jeu dans leur usage déclaré des TIC. Par socialisation professionnelle, nous e...

Evaluer des études de gestion des entreprises : combiner des éléments principales avec des éléments pratiques

NARCIS (Netherlands)

Pennink, B.J.W.

2002-01-01

Evaluer la recherche de gestion demande une combinaison des critères classiques et des critères pratiques. Par cette combinaison il est possible de trouver une réponse cerrecte concernant la validité et l'effet de la recherche. Dans cet article nous allons décrire comment une combinaison des

Aspects des Onychomycoses chez des patients camerounais de ...

African Journals Online (AJOL)

... biologiques et évolutifs des onychomycoses chez des patients camerounais. Méthode : Il s'agit d'une étude rétrospective et descriptive menée de mars 2011 à mars 2014 dans l'unité de dermatologie de l'hôpital général de Douala (HGD), incluant des patients chez lesquels le diagnostic d'onychomycose avait été posé.

Increasing the thermopower of crown-ether-bridged anthraquinones

Science.gov (United States)

Ismael, Ali K.; Grace, Iain; Lambert, Colin J.

2015-10-01

We investigate strategies for increasing the thermopower of crown-ether-bridged anthraquinones. The novel design feature of these molecules is the presence of either (1) crown-ether or (2) diaza-crown-ether bridges attached to the side of the current-carrying anthraquinone wire. The crown-ether side groups selectively bind alkali-metal cations and when combined with TCNE or TTF dopants, provide a large phase-space for optimising thermoelectric properties. We find that the optimum combination of cations and dopants depends on the temperature range of interest. The thermopowers of both 1 and 2 are negative and at room temperature are optimised by binding with TTF alone, achieving thermpowers of -600 μV K-1 and -285 μV K-1 respectively. At much lower temperatures, which are relevant to cascade coolers, we find that for 1, a combination of TTF and Na+ yields a maximum thermopower of -710 μV K-1 at 70 K, whereas a combination of TTF and Li+ yields a maximum thermopower of -600 μV K-1 at 90 K. For 2, we find that TTF doping yields a maximum thermopower of -800 μV K-1 at 90 K, whereas at 50 K, the largest thermopower (of -600 μV K-1) is obtain by a combination TTF and K+ doping. At room temperature, we obtain power factors of 73 μW m-1 K-2 for 1 (in combination with TTF and Na+) and 90 μW m-1 K-2 for 2 (with TTF). These are higher or comparable with reported power factors of other organic materials.We investigate strategies for increasing the thermopower of crown-ether-bridged anthraquinones. The novel design feature of these molecules is the presence of either (1) crown-ether or (2) diaza-crown-ether bridges attached to the side of the current-carrying anthraquinone wire. The crown-ether side groups selectively bind alkali-metal cations and when combined with TCNE or TTF dopants, provide a large phase-space for optimising thermoelectric properties. We find that the optimum combination of cations and dopants depends on the temperature range of interest. The

Development and characterization of poli composites (ether ether ketone)(PEEK)(Hydroxyapatite(HA)

International Nuclear Information System (INIS)

Ferreira, V.P.; Santos, F.S.F.; Sa, M.D. de; Fook, M.V.L.

2016-01-01

The objective of this work was to develop PEEK / HA composites, combining the biological activity of the ceramic phase with the properties of the polymer phase, the materials used in this research were Poly (ether-ether-ketone) (PEEK) and Hydroxyapatite (HA) (50, 60, 70 and 80% m / v HA), this material was subjected to a load of two tons followed by a thermal treatment at 390 ° for a period of 30 minutes. Then they were characterized by FTIR, DRX and MO. In the physical-chemical characterization of FTIR and XRD, it was not possible to identify significant alterations. In the FTIR spectra of the composites, there is no formation of new identifiable chemical bonds. In the composites XRD diffractograms a profile similar to the ceramic phase was observed, with peaks increasing in intensity and narrowing proportional to the increase of the hydroxyapatite concentration in the composites. In optical microscopy it is possible to observe surfaces with heterogeneous morphology, with signs of roughness and in the cross section we observe a heterogeneous aspect, rich in regions with large agglomerates and lighter particles. Considering the processing aspects, the technique proved to be effective for the development of PEEK /HA composites. (author)

A novel sulfonated poly(ether ether ketone) and cross-linked membranes for fuel cells

Energy Technology Data Exchange (ETDEWEB)

Li, Hongtao; Zhang, Gang; Wu, Jing; Zhao, Chengji; Zhang, Yang; Shao, Ke; Han, Miaomiao; Lin, Haidan; Zhu, Jing; Na, Hui [Alan G MacDiarmid Institute, College of Chemistry, Jilin University, Qianjin Street 2699, Changchun 130012, Jilin (China)

2010-10-01

A novel poly(ether ether ketone) (PEEK) containing pendant carboxyl groups has been synthesized by a nucleophilic polycondensation reaction. Sulfonated polymers (SPEEKs) with different ion exchange capacity are then obtained by post-sulfonation process. The structures of PEEK and SPEEKs are characterized by both FT-IR and {sup 1}H NMR. The properties of SPEEKs as candidates for proton exchange membranes are studied. The cross-linking reaction is performed at 140 C using poly(vinyl alcohol) (PVA) as the cross-linker. In comparison with the non-cross-linked membranes, some properties of the cross-linked membranes are significantly improved, such as water uptake, methanol resistance, mechanical and oxidative stabilities, while the proton conductivity decreases. The effect of PVA content on proton conductivity, water uptake, swelling ratio, and methanol permeability is also investigated. Among all the membranes, SPEEK-C-8 shows the highest selectivity of 50.5 x 10{sup 4} S s cm{sup -3}, which indicates that it is a suitable candidate for applications in direct methanol fuel cells. (author)

Rheological, mechanical and tribological properties of carbon-nanofibre reinforced poly (ether ether ketone composites

Directory of Open Access Journals (Sweden)

Volker Altstaedt

2003-12-01

Full Text Available Poly(ether ether ketone nanocomposites containing vapour-grown carbon nanofibres (CNF were produced using standard polymer processing techniques. At high shear rates no significant increase in resin viscosity was observed. Nevertheless, the addition of the CNFs results in a higher melt strength at 360°C. Electron microscopy confirmed the homogeneous dispersion and alignment of nanofibres in the polymer matrix. Evaluation of the mechanical composite properties revealed a linear increase in tensile stiffness and strength with nanofibre loading fractions up to 15 wt% whilst matrix ductility was maintained up to 10 wt%. An interpretation of the composite performance by short-fibre theory resulted in rather low intrinsic stiffness properties of the vapour-grown CNF. Differential scanning calorimetry was used to investigate crystallization kinetics and degree of crystallinity. The CNFs were found not to act as nucleating sites. Furthermore, unidirectional sliding tests against two different counterpart materials (100Cr6 martensitic bearing steel, X5CrNi18-10 austenitic stainless steel were performed. The carbon nanofibres were found to reduce the wear rate of PEEK significantly.

Le Gaz Naturel Véhicule Natural Gas for Vehicles

Directory of Open Access Journals (Sweden)

De Chauveron S.

2006-11-01

Full Text Available Cet article présente le GNV (Gaz Naturel Véhicule. Le GNV a en effet de sérieux atouts, à la fois comme carburant de substitution et comme carburant propre. Ces atouts sont aussi bien économiques que techniques. La première partie est consacrée aux enjeux du développement du GNV. Les premiers pays utilisateurs ont été ceux qui disposent sur leur sol de ressources de gaz naturel. Aujourd'hui, alors que de nombreux pays doivent faire face à l'inquiétude croissante relative à l'augmentation de la pollution urbaine, le gaz naturel apparaît également comme un carburant propre, permettant de réduire rapidement les émissions de polluants des véhicules. Dans une deuxième partie, nous donnons une description technique sommaire des stations GNV et des véhicules GNV. Il s'agit de familiariser le lecteur avec les quelques spécificités techniques du GNV, par rapport à l'essence et au gazole. On constatera d'ailleurs que les technologies GNV sont très proches des technologies classiques. Enfin, la dernière partie est consacrée aux actions en cours, qui permettront le développement du GNV en France et en Europe : programmes de recherche, réduction des coûts de la filière, actions réglementaires, communication, etc. This article presents compressed natural gas for vehicles (CNG, which can provide considerable advantages both as an alternative fuel and as a clean fuel. These assets are not only economic but also technical. The first part deals with what is at stake in developing natural gas as a motor fuel. The first countries to use CNG were those with natural gas resources in their subsoil. Today, with a large number of countries having to cope with growing concern about increasing urban pollution, natural gas is also seen as a clean fuel that can help cut vehicle pollutant emissions dramatically. In the second part a brief technical description is given of CNG stations and vehicles, with the aim of acquainting the reader with

Contribution to the study of the (U,Pu)C,N system; Contribution a l'etude du systeme (U,Pu)C,N

Energy Technology Data Exchange (ETDEWEB)

Lorenzelli, R [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The reactions of UC, PuC, (U,Pu)C, UC{sub 2} and U(C{sub 1-x}O{sub x}) with nitrogen at moderate temperatures (room temperature to 400 C) are described. The influence of the uptake of nitrogen by the powders necessary to sinter the carbides upon the nature of the final product has been investigated; it has been shown that the sintered carbides are hyper-stoichiometric. The reactions of carbon with UN, PuN and (U,Pu)N has also been studied. Under vacuum, carbon reacts on the nitrides at temperatures as low as 1100 C; nitrogen is replaced by carbon and the final product is a carbonitride. The reaction is: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. The reaction is limited and the carbonitrides have a fixed composition in presence of M{sub 2}C{sub 3} or MC{sub 2}; hence it is impossible to produce pure MC using the reaction. The ternary diagram U-C-N, Pu-C-N and (U,Pu)C-N have been drawn. They show clearly that it is possible to obtain single phase carbonitrides in a wide domain of compositions. (author) [French] On decrit les reactions avec l'azote de UC, PuC,(U,Pu)C,UC{sub 2} et U(C{sub 1-x}O{sub x}), par action directe de l'azote a temperature moderee (de l'ambiante a 450 C). On a etudie l'influence de la contamination par l'azote des poudres de carbures necessaires au frittage sur la nature des produits frittes; on a montre que les carbures frittes obtenus sont hyperstoechiometriques. On a etudie parallelement les reactions du carbone avec UN, PuN et (U,Pu)N. Sous vide le carbone reagit sur les nitrures des 1100 C: le carbone se substitue a l'azote; l'azote libere est elimine et le produit final est un carbonitrure. La reaction s'ecrit: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. La reaction est limitee et les carbonitrures obtenus ont une composition limite fixe en presence des carbures superieurs M{sub 2}C{sub 3} et MC{sub 2}; il est donc impossible d'obtenir MC pur par cette reaction. Les diagrammes d'equilibre U-C-N, Pu-C-N et (U,Pu) C-N, ont

Contribution to the study of the (U,Pu)C,N system; Contribution a l'etude du systeme (U,Pu)C,N

Energy Technology Data Exchange (ETDEWEB)

Lorenzelli, R. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The reactions of UC, PuC, (U,Pu)C, UC{sub 2} and U(C{sub 1-x}O{sub x}) with nitrogen at moderate temperatures (room temperature to 400 C) are described. The influence of the uptake of nitrogen by the powders necessary to sinter the carbides upon the nature of the final product has been investigated; it has been shown that the sintered carbides are hyper-stoichiometric. The reactions of carbon with UN, PuN and (U,Pu)N has also been studied. Under vacuum, carbon reacts on the nitrides at temperatures as low as 1100 C; nitrogen is replaced by carbon and the final product is a carbonitride. The reaction is: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. The reaction is limited and the carbonitrides have a fixed composition in presence of M{sub 2}C{sub 3} or MC{sub 2}; hence it is impossible to produce pure MC using the reaction. The ternary diagram U-C-N, Pu-C-N and (U,Pu)C-N have been drawn. They show clearly that it is possible to obtain single phase carbonitrides in a wide domain of compositions. (author) [French] On decrit les reactions avec l'azote de UC, PuC,(U,Pu)C,UC{sub 2} et U(C{sub 1-x}O{sub x}), par action directe de l'azote a temperature moderee (de l'ambiante a 450 C). On a etudie l'influence de la contamination par l'azote des poudres de carbures necessaires au frittage sur la nature des produits frittes; on a montre que les carbures frittes obtenus sont hyperstoechiometriques. On a etudie parallelement les reactions du carbone avec UN, PuN et (U,Pu)N. Sous vide le carbone reagit sur les nitrures des 1100 C: le carbone se substitue a l'azote; l'azote libere est elimine et le produit final est un carbonitrure. La reaction s'ecrit: MN + x C {yields} MN{sub 1-x}C{sub x} + x/2N{sub 2}. La reaction est limitee et les carbonitrures obtenus ont une composition limite fixe en presence des carbures superieurs M{sub 2}C{sub 3} et MC{sub 2}; il est donc impossible d'obtenir MC pur par cette reaction. Les diagrammes

Architecture, des normes et des systèmes d'information libres, phase ...

International Development Research Centre (IDRC) Digital Library (Canada)

Architecture, des normes et des systèmes d'information libres, phase II (OASIS II) - Renforcement des capacités dans l'ensemble de l'Afrique. Sur presque tout le continent africain, la prestation des services de santé est limitée en raison des maigres ressources disponibles et de la charge de morbidité de plus en plus ...

Ether gas-sensor based on Au nanoparticles-decorated ZnO microstructures

Directory of Open Access Journals (Sweden)

Roberto López

Full Text Available An ether gas-sensor was fabricated based on gold nanoparticles (Au-NPs decorated zinc oxide microstructures (ZnO-MS. Scanning electron microscope (SEM and high-resolution transmission electron microscope (HRTEM measurements were performed to study morphological and structural properties, respectively, of the ZnO-MS. The gas sensing response was evaluated in a relatively low temperature regime, which ranged between 150 and 250 °C. Compared with a sensor fabricated from pure ZnO-MS, the sensor based on Au-NPs decorated ZnO-MS showed much better ether gas response at the highest working temperature. In fact, pure ZnO-MS based sensor only showed a weak sensitivity of about 25%. The improvement of the ether gas response for sensor fabricated with Au-NPs decorated ZnO-MS was attributed to the catalytic activity of the Au-NPs. Keywords: ZnO microstructures, Au nanoparticles, Ether, Gas sensor

L'exode des cerveaux et le renforcement des capacités en Afrique ...

International Development Research Centre (IDRC) Digital Library (Canada)

1 févr. 2011 ... Ce phénomène ébranle les assises économiques et politiques de bien des pays africains. ... le défi consiste à recruter ces cerveaux. ... des missions africaines, des organisations non gouvernementales et des groupes de la diaspora réunis pour parler de l'exode des cerveaux en Afrique et des stratégies à ...

Influence de l'occupation des terres sur la dynamique des ...

African Journals Online (AJOL)

L'objectif de la présente étude est d'évaluer l'impact de mise en culture, des pâturages, des jachères et l'influence des villages sur la dynamique des communautés végétales de la commune de ..... mais il n'y a que peu de recrutement. Au-delà de cinq ans, taille et phytovolume diminuent, témoignant du vieillissement de la ...

Biomedical potentials of crown ethers: prospective antitumor agents.

Science.gov (United States)

Kralj, Marijeta; Tusek-Bozić, Ljerka; Frkanec, Leo

2008-10-01

Crown ethers are of enormous interest and importance in chemistry, biochemistry, materials science, catalysis, separation, transport and encapsulated processes, as well as in the design and synthesis of various synthetic systems with specific properties, diverse capabilities, and programmable functions. Classical crown ethers are macrocyclic polyethers that contain 3-20 oxygen atoms separated from each other by two or more carbon atoms. They are exceptionally versatile in selectively binding a range of metal ions and a variety of organic neutral and ionic species. Crown ethers are currently being studied and used in a variety of applications beyond their traditional place in chemistry. This review presents additional applications and the ever-increasing biomedical potentials of these intriguing compounds, with particular emphasis on the prospects of their relevance as anticancer agents. We believe that further research in this direction should be encouraged, as crown compounds could either induce toxicities that are different from those of conventional antitumor drugs, or complement drugs in current use, thereby providing a valuable adjunct to therapy.

Diethyl Ether Production Process with Various Catalyst Type

Directory of Open Access Journals (Sweden)

Widayat

2013-01-01

Full Text Available Several H-zeolite and HZSM-5 catalysts was preparated and their characters have also been investigated. H-zeolit Catalyst was preparated from Natural Zeolite that obtained from Malang District and Gunung Kidul District. Diethyl ether was produced by Ethanol with concentration of 95%. This research use fixed bed reactor that 1 gram of catalyst as bed catalyst, atmospheric pressure and temperature 140oC as the operating condition. Ethanol vapor from vaporization tank was driven by 200 ml/min Nitrogen stream. The responds in this research is liquid product concentration; diethyl ether, ethanol, methanol and water concentration. The results showed that the largest ethanol conversion was produced by the use of 56.44% HZSM-5 and the largest yield of diethyl ether diethyl was produced by the use of alumina and H-zeolite catalyst. The larger ratio between natural zeolite with HCl solvent will produce the larger surface area of catalyst and ethanol conversion. The largest ethanol conversion was produced at reactan ratio 1:20.

Proton-conducting membranes based on benzimidazole-containing sulfonated poly(ether ether ketone) compared with their carboxyl acid form

Energy Technology Data Exchange (ETDEWEB)

Li, Hongtao; Wu, Jing; Zhao, Chengji; Zhang, Gang; Zhang, Yang; Shao, Ke; Xu, Dan; Lin, Haidan; Han, Miaomiao; Na, Hui [Alan G MacDiarmid Institute, College of Chemistry, Jilin University, Changchun 130012 (China)

2009-10-15

A series of sulfonated poly(ether ether ketone) containing pendant carboxyl (C-SPEEKs) have been synthesized using a nucleophilic polycondesation reaction. A condensation reaction between 1,2-diaminobenzene and carboxyl resulted in a new series of copolymers containing benzimidazole groups (SPEEK-BIms). The expected structures of the sulfonated copolymers are confirmed by {sup 1}H NMR. The dependence of ion exchange capacity, water uptake, proton conductivity and methanol diffusion coefficient of SPEEK-BIm membranes has been studied and compared with their carboxyl acid form. The results suggest that the introduction of benzimidazole groups may be responsible for many excellent properties of the membranes for fuel cell. It is noticeable that the markedly improved oxidative stability is benefit for the application of membrane. (author)

Protective effects of ether, oxygen and their mixture for radiation in Drosophila melanogaster

International Nuclear Information System (INIS)

Megumi, Tsuneo; Tsujii, Yukio; Gamo, Sumiko

1992-01-01

Protective effects of ether mixed with air or oxygen against ionizing radiation damages were demonstrated in adult flies of Drosophila melanogaster. The protective effects against knock-down on the second day and lethality on the eighth day after irradiation were not affected by the radiation sensitivity and DNA repair capacity of the strains. Ether (4.2%) in oxygen was more effective than ether in air for both endpoints. The protective effects may be due to damages not involving cell division, since no mitotic cells are observed in adult flies except in gonadal glands. A change in the orderliness of the cell membrane by ether is suggested to be the cause of the protective effects. (author). 16 refs.; 3 tabs

GENOMIQUE ET LIPIDES Génomique et métabolisme des lipides des plantes

Directory of Open Access Journals (Sweden)

Delseny Michel

2002-03-01

Full Text Available Il existe dans les bases de données publiques une énorme quantité de séquences d’ADN dérivées de plantes, et notamment la séquence complète du génome d’Arabidopsis thaliana, une plante modèle pour les oléagineux, proche parente du colza. Ces données constituent une ressource importante non seulement pour la compréhension de métabolisme lipidique et de sa régulation, mais aussi pour la sélection et le développement de variétés nouvelles d’oléagineux produisant davantage d’huiles ou des huiles de composition nouvelle. Cette abondance de séquences peut être exploitée, en utilisant les recherches d’homologies, pour identifier les gènes, pour obtenir des informations sur leur fonction, comme pour repérer des gènes candidats codant des fonctions nouvelles. L’analyse de ces bases de données a révélé que la majeure partie des gènes codant des enzymes impliquées dans le métabolisme lipidique appartient à des petites familles multigéniques, reflétant la diversification des fonctions des isoformes. Une analyse du catalogue des ADNc séquencés en aveugle reflète les niveaux d’expression des différents gènes et fournit un aperçu des régulations des flux au travers des voies métaboliques conduisant à la biosynthèse des lipides de réserve. La disponibilité de mutants et de lignées transgéniques d’Arabidopsis et le développement de puces à ADN qui permettent l’analyse simultanée de plusieurs milliers de gènes conduiront à une meilleure compréhension des facteurs qui régulent le métabolisme des huiles dans les graines. Une telle connaissance facilitera la manipulation de la composition des huiles et des quantités produites dans les graines.

Des dispositions responsables à prendre pour la protection des ...

African Journals Online (AJOL)

En considérant l'effet néfaste des maladies, des parasites, du changement climatique et d'autres facteurs environnementaux (les OGM par exemple) sur la survie des abeilles, la baisse de leurs populations dans certaines parties du monde ne saurait être attribuée aux seules pesticides. En plus, l'impact de ces derniers sur ...

Radiolytic decomposition of 4-bromodiphenyl ether

International Nuclear Information System (INIS)

Tang Liang; Xu Gang; Wu Wenjing; Shi Wenyan; Liu Ning; Bai Yulei; Wu Minghong

2010-01-01

Polybrominated diphenyl ethers (PBDEs) spread widely in the environment are mainly removed by photochemical and anaerobic microbial degradation. In this paper, the decomposition of 4-bromodiphenyl ether (BDE -3), the PBDEs homologues, is investigated by electron beam irradiation of its ethanol/water solution (reduction system) and acetonitrile/water solution (oxidation system). The radiolytic products were determined by GC coupled with electron capture detector, and the reaction rate constant of e sol - in the reduction system was measured at 2.7 x 10 10 L · mol -1 · s -1 by pulsed radiolysis. The results show that the BDE-3 concentration affects strongly the decomposition ratio in the alkali solution, and the reduction system has a higher BDE-3 decomposition rate than the oxidation system. This indicates that the BDE-3 was reduced by effectively capturing e sol - in radiolytic process. (authors)

Gestion des risques

CERN Document Server

Louisot, Jean-Paul

2009-01-01

Depuis le début du lie siècle, la gestion des risques connaît une véritable révolution culturelle. Jusqu'alors fonction technique, centrée autour de l'achat de couverture d'assurances, elle est devenue une discipline managériale et transversale : une valise d'instruments que chaque manager doit connaître et appliquer quels que soient son domaine de compétence et ses missions au sein de l'organisation. En effet, la gestion des risques est une culture qui doit être assimilée par chacun des acteurs. C'est précisément l'ambition des 101 questions rassemblées dans cet ouvrage : apporter à chaque manager d'entreprise, de collectivité, d'établissement de santé..., des réponses claires au " pourquoi " et au " comment " : Comment identifier les risques ? Comment analyser les risques ? Quels sont les objectifs de la gestion des risques ? Une carte des risques pour quoi faire ? Pourquoi faut-il financer les risques ? Les entreprises ont-elles des responsabilités pénales ? En quoi consiste la gestion...

Comportement des polluants des eaux pluviales urbaines en ...

African Journals Online (AJOL)

développement et la croissance des organismes vivant dans l'eau et particulièrement les micro- organismes. Le suivi des températures enregistrées oscille entre 9 et 16°C dans les trois sites d'observation durant la période ... de la lumière du soleil. Le site C est bien aéré et .... Effets de différents modes de gestion des eaux ...

Spino ether and its vortices: leptons and hadrons

Energy Technology Data Exchange (ETDEWEB)

Skorski, R [College of Engineering, Univ. of Alabama, Alabama (USA)

1977-03-01

According to the theory advanced by the author, space is occupied by a spino ether lattice. Where no spino lattice exists, there are black holes. The spino is a kind of massive neutrino with a rest mass of about 7.39x10/sup -47/g and a diameter of 4.56x10/sup -34/cm. The distance between spinos in the spino lattice is about 2x10/sup -10/cm. Spino ether is ubiquitous in all matter, pervades atoms and their nuclei and penetrates matter with no resistance. In fact, hadrons and leptons are shown to be vortices of the spino ether. About one km/sup 3/ of space contains spino ether having a mass equal to 10/sup 80/ baryons, equivalent to the total mass of our universe. If the distances between spinos equaled their diameters, 4.56x10/sup -34/cm instead of 2x10/sup -10/cm, then the diameter of the mass equivalent to our universe would be about 2cm. This is in agreement with the size of the premordial universe, before its explosion, as calculated earlier by other theories. It is conjectured that explosions of energy and mass in space are more frequent on a smaller scale than those in the universe, for example novas, or even on a still smaller scale usually associated with the birth of different nuclei. The abundance of iron in the solar corona, on the surface of Mars, and in the Martin sky appears to be due to hadron formation from space itself.

Dimethylzinc-Initiated Radical Coupling of β-Bromostyrenes with Ethers and Amines

DEFF Research Database (Denmark)

Sølvhøj, Amanda Birgitte; Ahlburg, Andreas; Madsen, Robert

2015-01-01

A new coupling reaction has been developed in which β-bromostyrenes react with ethers and tertiary amines to introduce the styryl group in the α-position. The transformation is mediated by Me2Zn/O2 with 10 % MnCl2 and is believed to proceed by a radical addition-elimination mechanism. The ether...... and the amine are employed as solvent and the coupling takes place through the most stable α radical for unsymmetrical substrates. The products are obtained in moderate to good yields as the pure E isomers. The coupling can be achieved with a range of smaller cyclic and acyclic ethers/amines as well as various...

Caractérisation des plantes médicinales à flavonoïdes des marchés ...

African Journals Online (AJOL)

Les espèces guinéo-congolaises sont les plus abondantes et le mode de dissémination majoritaire des diaspores est la zoochorie. Les plantes à flavonoïdes les plus utilisées sont : Combretum micranthum, Aloe vera, Ageratum conyzoïdes et Cylicodiscus gabonensis. Elles rentrent dans le traitement de 73 maladies parmi ...

Poly (ether ether ketone) membranes for fuel cells; Membranas de poli (eter eter cetona) sulfonado para celulas a combustivel

Energy Technology Data Exchange (ETDEWEB)

Marrero, Jacqueline C.; Gomes, Ailton de S.; Filho, Jose C.D., E-mail: jacquecosta@gmail.com [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Hui, Wang S. [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil); Oliveira, Vivianna S. de [Escola Tecnica Rezende-Rammel, Rio de Janeiro, RJ (Brazil)

2015-07-01

Polymeric membranes were developed using a SPEEK polymer matrix (sulphonated poly (ether ether ketone)), containing hygroscopic particles of zirconia (Zr) (incorporated by sol-gel method), for use as electrolyte membranes in fuel cells. SPEEK with different sulfonation degrees were used: 63 and 86%. The thermal analysis (TGA and DSC) was carried out to characterize the membranes and electrochemical impedance spectroscopy (EIS) was carried out to evaluating the proton conductivity of the membranes. Additional analysis were underway in order to characterize these membranes, which include: X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) in order to evaluate the influence of zirconia and sulfonation degree on the properties of the membranes. (author)

Impact de la preparation des anodes crues et des conditions de cuisson sur la fissuration dans des anodes denses

Science.gov (United States)

Amrani, Salah

La fabrication de l'aluminium est realisee dans une cellule d'electrolyse, et cette operation utilise des anodes en carbone. L'evaluation de la qualite de ces anodes reste indispensable avant leur utilisation. La presence des fissures dans les anodes provoque une perturbation du procede l'electrolyse et une diminution de sa performance. Ce projet a ete entrepris pour determiner l'impact des differents parametres de procedes de fabrication des anodes sur la fissuration des anodes denses. Ces parametres incluent ceux de la fabrication des anodes crues, des proprietes des matieres premieres et de la cuisson. Une recherche bibliographique a ete effectuee sur tous les aspects de la fissuration des anodes en carbone pour compiler les travaux anterieurs. Une methodologie detaillee a ete mise au point pour faciliter le deroulement des travaux et atteindre les objectifs vises. La majorite de ce document est reservee pour la discussion des resultats obtenus au laboratoire de l'UQAC et au niveau industriel. Concernant les etudes realisees a l'UQAC, une partie des travaux experimentaux est reservee a la recherche des differents mecanismes de fissuration dans les anodes denses utilisees dans l'industrie d'aluminium. L'approche etait d'abord basee sur la caracterisation qualitative du mecanisme de la fissuration en surface et en profondeur. Puis, une caracterisation quantitative a ete realisee pour la determination de la distribution de la largeur de la fissure sur toute sa longueur, ainsi que le pourcentage de sa surface par rapport a la surface totale de l'echantillon. Cette etude a ete realisee par le biais de la technique d'analyse d'image utilisee pour caracteriser la fissuration d'un echantillon d'anode cuite. L'analyse surfacique et en profondeur de cet echantillon a permis de voir clairement la formation des fissures sur une grande partie de la surface analysee. L'autre partie des travaux est basee sur la caracterisation des defauts dans des echantillons d'anodes crues

IRON(III) NITRATE-CATALYZED FACILE SYNTHESIS OF DIPHENYLMETHYL (DPM) ETHERS FROM ALCOHOLS

Science.gov (United States)

Diphenyl methyl (DPM) ethers constitute important structural portion of some pharmaceutical entities and also as protective group for hydroxyl groups in synthetic chemistry. DPM ethers are normally prepared using concentrated acids or base as catalysts, which may result in the fo...

La cire cuticulaire des grains de raisin et des feuilles de la vigne

Directory of Open Access Journals (Sweden)

F. RADLER

1968-06-01

Full Text Available Je voudrais parler ici des recherches que j'ai effectuées dans le cadre d'un programme de recherches de l'Organisation australienne de recherches (C.S.I.R.O.. Ce sont des recherches sur la structure, la composition chimique et le rôle de la cire cuticulaire des grains de raisins et des feuilles. Ces recherches ont été effectuées principalement lors de l'étude des problèmes relatifs au séchage des raisins pour la production des raisins. Cependant, l'importance de la cire cuticulaire ne se limite pas seulement au séchage des raisins, car elle concerne aussi l'œnologie et les problèmes de la conservation des raisins de table. Je pense donc que mon exposé peut présenter pour vous un certain intérêt.

statut de la matiere organique des cambisols et des lixisols sous

African Journals Online (AJOL)

Administrateur

L'étude vise à évaluer la matière organique des Cambisols et des Lixisols sous formations naturelles de longue durée en zone climatique nord-soudanienne et à établir, les relations entre ... sont supérieures à celles des sols des zones sahélienne et sud-soudanienne. ... globale a eu une corrélation positive avec le pH.

Fiabilité des structures mécaniques adaptatives: effet de la panne des actionneurs ou des capteurs sur la stabilité

Science.gov (United States)

Fall, H.; Charon, W.; Kouta, R.

2002-12-01

Ces dernières décennies, des activités significatives dans le monde étaient dirigées autour du contrôle actif. Le but de ces recherches était essentiellement d'améliorer les performances, la fiabilité et la sécurité des systèmes. Notamment dans le cas des structures soumises à des vibrations aléatoires. D'importants travaux ont été consacré à l'utilisation des “matériaux intelligents” comme capteurs et actionneurs. Cette article propose l'analyse de la fiabilité des systèmes mécaniques en étudiant les pannes des actionneurs ou des capteurs. L'effet de ces pannes sur la stabilité et la performance du système y est démontré. Les méthodologies de conception y sont rappelées. Des exemples numériques sont fournis à travers le contrôle d'un panneau sous chargement dynamique pour illustrer la méthode proposée.

Thermal and oxidative degradation studies of formulated C-ethers by gel-permeation chromatography

Science.gov (United States)

Jones, W. R., Jr.; Morales, W.

1982-01-01

Gel-permeation chromatography was used to analyze C-ether lubricant formulations from high-temperature bearing tests and from micro-oxidation tests. Three mu-styragel columns (one 500 and two 100 A) and a tetrahydrofuran mobile phase were found to adequately separate the C-ether degradation products. The micro-oxidation tests yielded degradation results qualitatively similar to those observed from the bearing tests. Micro-oxidation tests conducted in air yielded more degradation than did tests in nitrogen. No great differences were observed between the thermal-oxidative stabilities of the two C-ether formulations or between the catalytic degradation activities of silver and M-50 steel. C-ether formulation I did yield more degradation than did formulation II in 111- and 25-hour bearing tests, respectively.

Évaluation des émissions de gaz à effet de serre des filières de traitement et de valorisation des boues issues du traitement des eaux usées

OpenAIRE

Reverdy, A.L.; Pradel, M.

2011-01-01

/ Ce rapport présente l'inventaire des différentes consommations énergétiques, en consommables et des GES pour chaque poste de traitement et de valorisation des boues issues du traitement des eaux usées.

BioTfueL Project: Targeting the Development of Second-Generation Biodiesel and Biojet Fuels Le projet BioTfueL : un projet de développement de biogazole et biokérosène de 2 génération

Directory of Open Access Journals (Sweden)

Viguié J.-C.

2013-10-01

Full Text Available 2nd generation biofuels will have an important part to take in the energy transition as far as fuels are concerned. Using non edible biomass, they will avoid any direct competition with food usage. Within 2nd generation biofuels, the BTL route consists in the production of middle distillates (Diesel and jet fuel via gasification and Fischer-Tropsch (FT synthesis. These fuels are called “drop in” fuels; this means that to be used they technically do not request any modification in the vehicle whatever the blending rate with conventional fuels. This route is currently at the pre-industrial phase where demonstration is required. This article presents the BioTfueL project which has been created by Axens, CEA, IFP Energies nouvelles, Sofiprotéol, ThyssenKrupp Uhde and Total. This project is focused on the original concept of co-processing (biomass can be gasified together with fossil feedstock and proposes to develop and demonstrate a full process chain to be commercialized worldwide via licensing. Les biocarburants de 2e génération ont un rôle important à jouer en ce qui concerne le pool carburant dans le cadre de la transition énergétique. Utilisant comme matière première de la biomasse non comestible, ces carburants éviteront toute compétition directe avec un usage alimentaire de cette ressource. Parmi les biocarburants de 2e génération, la voie BTL consiste en la production de distillats moyens (gazole moteur et carburéacteur via gazéification et synthèse Fischer-Tropsch (FT. Ces carburants sont communément appelés des « drop in fuels », ce qui signifie que techniquement ils ne nécessitent aucune modification du véhicule quelque soit leur taux d’incorporation dans les carburants traditionnels. Cette voie entre actuellement en phase préindustrielle pour laquelle une démonstration est nécessaire. Cet article présente le projet BioTfueL qui est porté par Axens, le CEA, IFP Energies nouvelles, Sofiprotéol, Thyssen

Direct dimethyl ether fueling of a high temperature polymer fuel cell

DEFF Research Database (Denmark)

Jensen, Jens Oluf; Vassiliev, Anton; Olsen, M.I.

2012-01-01

Direct dimethyl ether (DME) fuel cells suffer from poor DME–water miscibility and so far peak powers of only 20–40 mW cm−2 have been reported. Based on available literature on solubility of dimethyl ether (DME) in water at ambient pressure it was estimated that the maximum concentration of DME at...

Synthesis of Novel Bibrachial Lariat Ethers (BiBLEs) Containing [1,2 ...

African Journals Online (AJOL)

NICO

A practical and regioselective method for the synthesis of cis-diastereomers of bibrachial lariat ethers (BiBLEs) bearing ester and amide groups is reported. The novel bibrachial lariat ethers (BiBLEs) 3a–d with neutral side chains were prepared by reaction of the corresponding aza-crown macrocycles 1a–b with ethyl ...

Isothermal (vapor + liquid) equilibria and excess enthalpy data of {1-hexene + methyl butyl ether (MBE)} and {1-hexene + methyl tert-butyl ether (MTBE)} binary systems at several temperatures

International Nuclear Information System (INIS)

Hani, Rachida; Solimando, Roland; Negadi, Latifa; Jose, Jacques; Ait Kaci, Ahmed

2012-01-01

Highlights: ► Vapor pressures of (1-hexene + methyl butyl ether) or (1-hexene + methyl tert-butyl ether) are reported between (263 and 363) K. ► The two mixtures exhibit positive G E . ► Additionally, molar excess enthalpies, H E , for the two binary systems have been measured at 303.15. - Abstract: The vapor pressures of {1-hexene + methyl butyl ether (MBE)} and {1-hexene + methyl tert-butyl ether (MTBE)} binary mixtures and of the three pure components were measured by means of a static device at temperatures between (263 and 333) K. The data were correlated with the Antoine equation. From these data, excess Gibbs functions were calculated for several constant temperatures and fitted to a third-order Redlich–Kister equation using the Barker’s method. Additionally, molar excess enthalpies, H E , for the two binary systems have been measured at 303.15 K using an isothermal flow calorimeter.

Metabolism of nitrodiphenyl ether herbicides by dioxin-degrading bacterium Sphingomonas wittichii RW1.

Science.gov (United States)

Keum, Young Soo; Lee, Young Ju; Kim, Jeong-Han

2008-10-08

Nitrodiphenyl ether herbicides, including chlomethoxyfen, nitrofen, and oxyfluorfen are potent herbicides. Some metabolites and parent compounds are considered as possible mutagens and endocrine disruptors. Both properties pose serious hygienic and environmental risks. Sphingomonas wittichii RW1 is a well-known degrader of polychlorinated dibenzo- p-dioxins, dibenzofurans, and diphenyl ethers. However, no detailed research of its metabolic activity has been performed against pesticides with a diphenyl ether scaffold. In this study, we report S. wittichii RW1 as a very potent diphenyl ether herbicide-metabolizing bacterium with broad substrate specificity. The structures of metabolites were determined by instrumental analysis and synthetic standards. Most pesticides were rapidly removed from the culture medium in the order of nitrofen > oxyfluorfen > chlomethoxyfen. In general, herbicides were degraded through the initial reduction and N-acetylation of nitro groups, followed by ether bond cleavage. Relatively low concentrations of phenolic and catecholic metabolites throughout the study suggested that these metabolites were rapidly metabolized and incorporated into primary metabolism. These results indicate that strain RW1 has very versatile metabolic activities over a wide range of environmental contaminants.

Children's exposure to polybrominated diphenyl ethers.

NARCIS (Netherlands)

Zuurbier, M.; Leijs, M.; Schoeters, G.; Tusscher, G. Ten; Koppe, J.G.

2006-01-01

Background: Polybrominated biphenyl ethers (PBDEs), a class of brominated flame retardants, are frequently used in consumer products. PBDEs levels in environmental and human samples have increased in recent decades. Children are exposed to PBDEs through diet, mainly through fish, meat and milk.

Renforcement de l'autonomie des collectivités au moyen des ...

International Development Research Centre (IDRC) Digital Library (Canada)

Cette subvention permettra au ministère des Communications et des Technologies de l'information de l'Égypte ainsi qu'au fonds spécial réservé aux TI de consolider le modèle actuel des clubs de TI en Égypte, par l'entremise de services d'assistance sur demande, d'activités de formation à l'intention du personnel des ...

L' approche des options stratégiques des acteurs dans i' etude des relations tu travail

OpenAIRE

López Pino, Carmen Marina

2011-01-01

Faire une analyse de la proposition analytique développée par le MIT (Masachussetts Institute of Tecnology) inspirée du concept des options stratégiques pour I' objet de cet article. En premier lieu, les sujets traités seront la problematique des relations du travail et les découvertes fondamentales des différentes recherches de I' equipe du MIT. Après, I' étude fait une courte présentatión sur I' approche des systémes de Dunlop dont I' èquipe cherche améliorer. Ensuite, sont présentés...

D’une problématique locale-frontalière à un enjeu binational : le cas de la contrebande transfrontalière de carburants entre la Colombie et le Venezuela

Directory of Open Access Journals (Sweden)

Amanda Andrade Benitez

2011-10-01

Full Text Available Cet article propose d’appréhender le processus d’inscription de la question de la contrebande transfrontalière de carburants dans l’agenda d’intégration binational entre la Colombie et le Venezuela. Peu de travaux s’intéressent à ce sujet qui est habituellement abordé dans une perspective de politique intérieure et non pas extérieure. Notre étude s’inscrit dans le cadre théorique de la « mise en agenda » traitée par Cobb et Elders (1983 et des travaux de Jones et Baumgartner (2005 sur l’évolution de l’agenda politique après l’introduction de nouveaux enjeux. Elle vise à comprendre la manière dont la contrebande de carburants trouve une place dans l’agenda d’intégration énergétique bilatéral et devient un enjeu de coopération entre les deux pays. Les effets économiques de la contrebande ainsi que ses conséquences sur la sécurité de la frontière ont été des facteurs déterminants dans la signature d’un accord entre les deux pays. Les agences énergétiques de Colombie et du Venezuela ont été les acteurs privilégiés du processus d’inscription du problème dans l’agenda d’intégration entre les deux pays.This article analyzes the gradual inclusion of the illegal oil trade in the binational integration agenda between Venezuela and Colombia. Few scholars have focused on this question, which is generally examined through the prism of domestic –not foreign– policy. This study borrows from Cobb and Elders’ (1983 agenda setting theory and its development by Jones and Baumgartner (2005 on the evolution of political agendas following the incorporation of new issues. The purpose is to understand the ways in which illegal oil trade found its place in the bilateral energy integration agenda and became the subject of cooperation between Venezuela and Colombia. The economic effects of this illegal traffic along with its consequences on border security were crucial factors in the signing of a

Mechanical properties and chemical stability of pivalolactone-based poly(ether ester)s

NARCIS (Netherlands)

Tijsma, E.J.; Tijsma, E.J.; van der Does, L.; Bantjes, A.; Bantjes, A.; Vulic, I.

1994-01-01

The processing, mechanical and chemical properties of poly(ether ester)s, prepared from pivalolactone (PVL), 1,4-butanediol (4G) and dimethyl terephthalate (DMT), were studied. The poly(ether ester)s could easily be processed by injection moulding, owing to their favourable rheological and thermal

Developpement des betons semi autoplacants a rheologie adaptee pour des infrastructures

Science.gov (United States)

Sotomayor Cruz, Cristian Daniel

Au cours des dernières décennies, les infrastructures canadiennes et québécoises comportent plusieurs structures en béton armé présentant des problèmes de durabilité dus aux conditions climatiques sévères, à la mauvaise conception des structures, à la qualité des matériaux, aux types des bétons choisis, aux systèmes de construction ou à l'existence d'événements incontrôlables. En ce qui concerne le choix du béton pour la construction des infrastructures, une vaste gamme de béton divisée en deux principaux types peut être utilisée: le béton conventionnel vibré (BCV) et le béton autoplaçant (BAP). Dans le cas d'un BCV, la consolidation inadéquate par vibration a été un problème récurrent, occasionnant des dommages structuraux. Ceci a conduit à une réduction de la durabilité et à une augmentation du coût d'entretien et de réparation des infrastructures. Rien que l'utilisation d'un BAP a des avantages tels que l'élimination de la vibration, la réduction des coûts de main d'oeuvre et l'amélioration de la qualité des structures, néanmoins, le coût initial d'un BAP par rapport à un BCV ne permet pas encore de généraliser son utilisation dans l'industrie de la construction. Ce mémoire présente la conception d'une nouvelle gamme de béton semi-autoplaçant pour la construction des infrastructures (BSAP-I) exigeant une vibration minimale. Il s'agit de trouver un équilibre optimal entre la rhéologie et le coût initial du nouveau béton pour conférer une bonne performance structurale et économique aux structures. Le programme expérimental établi a premièrement permis d'évaluer la faisabilité d'utilisation des BSAP-I pour la mise en place des piliers d'une infrastructure de pont à Sherbrooke. En plus, l'utilisation d'un plan d'expériences a permis l'évaluation de trois paramètres de formulation sur les propriétés des mélanges de BSAP-I à l'état frais et durci. Finalement, l'évaluation de la performance des

Libération des acides gras par autolyse enzymatique des triglycérides des graines oléoprotéagineuses

Directory of Open Access Journals (Sweden)

Alibert Gilbert

2001-01-01

Full Text Available Les acides gras produits par hydrolyse chimique des lipides des plantes sont des matériaux de base pour l’industrie des biocarburants, des lubrifiants, des plastiques, des détergents et également des adjuvants de préparations commerciales d’herbicides. Cependant les procédés actuels de production des acides gras sont hautement polluants et coûteux en énergie. Dans ce travail nous développons un nouveau procédé de production des acides gras mettant en œuvre des plantes génétiquement modifiées. Nous avons introduit dans le tabac, retenu comme plante modèle, une construction génétique comprenant un gène de lipase (de la levure Geotrichum candidum sous le contrôle d’un promoteur graine spécifique (promoteur AtEm1 d’Arabidopsis thaliana. Ce promoteur devrait permettre l’expression du gène de lipase au niveau de l’axe embryonnaire tandis que les lipides s’accumulent dans les corps lipidiques des cotylédons. Dans ces conditions, les lipides de la graine devraient être séparés de la lipase par une compartimentation tissulaire et ne pas interférer. Après broyage des graines on peut penser que la mise en contact des lipides et de la lipase conduira à la libération d’acides gras. Plusieurs transformants ont été produits par transfert de gène à l’aide d’Agrobacterium tumefaciens, quelques-uns d’entre eux exprimant, comme attendu, la lipase dans leurs graines. Trois clones (2, 19 et 43 présentent une activité lipase significative et ont été retenus pour des études complémentaires. Cependant l’activité enzymatique observée est faible et certains clones présentent un défaut de compartimentation entre l’enzyme et les lipides se traduisant par la production d’acides gras dans la graine intacte. Lorsque les graines du clone 43 sont broyées dans un tampon, des acides gras sont produits dans le milieu réactionnel, validant le procédé imaginé. De nouvelles constructions réalisées, soit

Paternité des articles et intérêts concurrents : une analyse des recommandations aux auteurs des journaux traitant de pratique pharmaceutique

Science.gov (United States)

Courbon, Ève; Tanguay, Cynthia; Lebel, Denis; Bussières, Jean-François

2014-01-01

RÉSUMÉ Contexte : La présence d’auteurs honorifiques et fantômes ainsi que les intérêts concurrents représentent des difficultés bien documentées, liées à la publication d’articles scientifiques. Il existe des lignes directrices encadrant la rédaction et la publication de manuscrits scientifiques, notamment celles de l’International Committee of Medical Journal Editors (ICMJE). Objectifs : L’objectif principal de cette étude descriptive et transversale visait à recenser les instructions portant sur la paternité des articles et les intérêts concurrents provenant des recommandations aux auteurs des journaux traitant de pratique pharmaceutique. L’objectif secondaire visait à déterminer des mesures correctrices pour une paternité des articles plus transparente. Méthode : La recherche a débuté par l’identification des journaux traitant de pratique pharmaceutique. La consultation des instructions aux auteurs des journaux a permis ensuite de recenser les recommandations destinées à éviter les problèmes de paternité des articles et d’intérêts concurrents. Finalement, les membres de l’équipe de recherche se sont consultés afin de définir des mesures correctrices possibles à l’intention des chercheurs. Résultats : Des 232 journaux traitant de pharmacie, 33 ont été définis comme traitant de pratique pharmaceutique. Un total de 24 (73 %) journaux mentionnaient suivre la politique de l’ICMJE, 14 (42 %) demandaient aux auteurs de remplir un formulaire de déclaration d’intérêts concurrents au moment de la soumission de l’article, 17 (52 %) présentaient une définition de la qualité d’auteur et 5 (15 %) demandaient de détailler les contributions de chaque auteur. Une grille de 40 critères a été élaborée pour définir l’attribution du statut d’auteur. Conclusion : Moins de la moitié des journaux demandait aux auteurs de transmettre un formulaire de déclaration des intérêts concurrents au moment de la

Flourimetric and prototropic studies on the inclusion complexation of 2-amino and 4-aminodiphenyl ethers with {beta}-cyclodextrin: Unusual behavior of 4-aminodiphenyl ether

Energy Technology Data Exchange (ETDEWEB)

Enoch, Israel V. Muthu Vijayan [Department of Chemistry, Annamalai University, Annamalainagar 608 002, Tamil Nadu (India); Swaminathan, Meenakshisundaram [Department of Chemistry, Annamalai University, Annamalainagar 608 002, Tamil Nadu (India)], E-mail: chemsam@yahoo.com

2007-12-15

The fluorescence characteristics of diphenyl ether (DPE), 2-aminodiphenyl ether (2ADPE) and 4-aminodiphenyl ether (4ADPE) and prototropic behavior of 2ADPE and 4ADPE on inclusion complexation with {beta}-cyclodextrin have been investigated. DPE forms 1:1 complex whereas 2ADPE and 4ADPE form 1:2 complex with {beta}-CDx. The fluorimetric and prototropic behaviors of 4ADPE in {beta}-CDx are different from those in aqueous solution. The dual fluorescence of 4ADPE in {beta}-CDx is found to be due to twisted intramolecular charge transfer (TICT) character induced by inclusion complexation. The two equilibria viz. monocation{r_reversible}monocation solvent exciplex{r_reversible}neutral reported for 4ADPE in aqueous solution are not observed in presence of {beta}-CDx. The ground and excited state pK{sub a} values for monocation-neutral equilibrium of 2ADPE and 4ADPE have been reported.

High Resolution Rotational Spectroscopy of a Flexible Cyclic Ether

Science.gov (United States)

Gámez, F.; Martínez-Haya, B.; Blanco, S.; López, J. C.; Alonso, J. L.

2011-06-01

Crown ethers stand as one cornerstone molecular class inhost-guest Supramolecular Chemistry and constitute building blocks for a broad range of modern materials. We report here the first high resolution rotational study of a crown ether: 1,4,7,10,13-pentaoxacyclopentadecane (15-crown-5 ether,15c5). Molecular beam Fourier transform microwave spectroscopy has been employed. The liquid sample of 15c5 has been vaporized using heating methods. The considerable size of 15c5 and the broad range of conformations allowed by the flexibility of its backbone pose important challenges to spectroscopy approaches. In fact, the ab-initio computational study for isolated 15c5, yields at least six stable conformers with relative free energies within 2 kJ Mol-1 (167 Cm-1). Nevertheless, in this investigation it has been possible to identify and characterize in detail one stable rotamer of the 15c5 molecule and to challenge different quantum methods for the accurate description of this system. The results pave the ground for an extensive description of the conformational landscape of 15c5 and related cyclic ethers in the near term. J. L. Alonso, F. J. Lorenzo, J. C. López, A. Lesarri, S. Mata and H. Dreizler, Chem. Phys., 218, 267 (1997) S. Blanco, J.C López, J.L. Alonso, P. Ottaviani, W. Caminati, J. Chem. Phys. 119, 880 (2003) S.E. Hill, D. Feller, Int. J. Mass Spectrom. 201, 41 (2000)

Solvent Effects on Cesium Complexation with Crown Ethers from Liquid to Supercritical Fluids

International Nuclear Information System (INIS)

Wai, Chien M.; Rustenholtz, Anne; Wang, Shaofen; Lee, Su-Chen; Herman, Jamie; Porter, Richard A.

2004-01-01

Nuclear magnetic resonance (NMR) techniques were used to study crown ether-water interactions in solvents of low dielectric constants such as chloroform and carbon tetrachloride. Water forms a 1:1 complex with a number of crown ethers including 12-crown-4, 15-crown-5, 18-crown-6, dicyclohexano-18=crown-6, dicyclohexano-24-crown 8, and dibenzl-24-crown-8 in chloroform. Among these crown ethers, the 18-crown-6-H2 complex has the largest equilibrium constant (K=545) and 97% of the crown is complexed to water in chloroform. Addition of carbon tetrachloride to chloroform lowers the equilibrium constants of the crown-water complexes. The partition coefficients of crown ethers (D=crown in water/crown in solvent) between water and organic solvent also vary with solvent composition

Contribution des radios communautaires a l'education des ...

African Journals Online (AJOL)

Contribution des radios communautaires a l'education des populations rurales pour un developpement durable au Benin: etude de cas. ... Journal de la Recherche Scientifique de l'Université de Lomé. Journal Home · ABOUT THIS JOURNAL ...

Rôle des germes parasites des bactéries pathogènes dans l'autoépuration des eaux

Directory of Open Access Journals (Sweden)

GUELIN A.

1969-04-01

Full Text Available Existence dans les eaux polluées de germes parasites qui s'attaquent aux bactéries pathogènes. Le pouvoir bactéricide des eaux polluées dû, en grande partie à la présence dans ces eaux de différents représentants des germes parasites. Possibilité d'application pratique des germes parasites pour l'assainissement des eaux polluées.

G2 and G3 reactors design; Description des reacteurs G2 et G3

Energy Technology Data Exchange (ETDEWEB)

Herreng,; Ertaud,; Pasquet, [Societe Alsacienne de Constructions Mecaniques (France)

1958-07-01

classique a trois etages (pressions 10,3: 2 et 0,5 kg/cm{sup 2}). On peut condenser la vapeur, en cas d'arret d'un groupe turbo-alternateur, sans modifier le regime de la pile. Des circuits annexes servent a assurer une epuration continue du CO{sub 2}, son stockage et sa vidange. La commande du reacteur est assuree par la manoeuvre de 49 barres en carbure de bore. La regulation de l'ensemble a pose des problemes difficiles dont les solutions seront completees par l'experience du fonctionnement. Des conferences speciales seront consacrees aux elements de combustibles et a la detection des ruptures de gaines. (auteur)

Etude expérimentale du cliquetis à haut régime Experimental Study of Hight-Speed Knocking

Directory of Open Access Journals (Sweden)

Guibet J. C.

2006-11-01

Full Text Available La première partie de cette étude a consisté à observer et à tenter d'interpréter l'action des conditions de fonctionnement et des paramètres de réglage du moteur sur la tendance au cliquetis à haut régime. On a montré ensuite que les différentes familles chimiques d'hydrocarbures qui constituent les carburants classiques présentent chacune un comportement bien distinct en fonction de la richesse, de la pression et de la température d'admission. On a également étudié l'influence de la teneur en plomb du carburant et du type d'alkyle de plomb employé. Quelques expériences ont été effectuées afin de déterminer l'incidence d'une réduction de un point de taux de compression sur l'exigence en octane à haut régime et sur l'action des caractéristiques de composition du carburant. Enfin, en déterminant le pourcentage de cycles soumis au cliquetis pour différentes avances à l'allumage, il a été possible de fournir quelques indications permettant de mieux caractériser l'intensité du phénomène. The first part of this study consists in observing and trying to interpret the effect of operating conditions and engine tuning parameters on the tendency for high-speed knocking to appear. The different chemical families of the hydrocarbons making up conventional fuels are shown to each have a quite different behavior depending on the fuel-air equivalency ratio and the admission pressure and temperature. The influence of the lead content in the fuel and of the type of lead alkyl used is also studied. Some experiments were performed to determine the influence of a one-point reduction in the compression ratio on the high-speed octane requirement and on the effect of fuel composition properties. Lastly, by determing the percentage of cycles accompanied by knocking at different spark advances, some indications were found for better characterizing the intensity of the phenomenon.

Pollution provoquée par le moteur Diesel. Niveaux d'émission. Comparaison avec le moteur à allumage commandé Pollution Caused by Diesel Engines. Emission Levels. Comparison with Spark-Ignition Engines

Directory of Open Access Journals (Sweden)

Degobert P.

2006-11-01

Full Text Available A partir de l'analyse des différences de modes de combustion allumage commandé et Diesel , cet article compare et explique la nature et les niveaux des différents polluants émis en fonction de leurs mécanismes de formation. Les facteurs d'action au niveau moteur sont examinés, ainsi que l'influence du carburant utilisé. Based on an analysis of the difference between spark-ignition and diesel combustion modes, this article compares and explains the nature and levels of different pollutants emitted as a function of their formation mechanisms. The action factors at the engine> level are examined together with the influence of the fuel used.

Radiation-induced glycoside bond breaking in cellulose methyl ethers

International Nuclear Information System (INIS)

Petryaev, E.P.; Boltromeyuk, V.V.; Kovalenko, N.I.; Shadyro, O.I.

1988-01-01

Radiation-induced destruction of cellulose methyl ethers of different degree of esterification in aqueous solutions with and without acceptors: (N 2 O, O 2 , H 2 O + , Co(2), Cu(2)) is investigated. It is established that OH radicals make main contribution into radiolytic transformations of cellulose ethers in aqueous solutions. Reactions of radicals with free valency on carbon atoms containing secondary nonsubstituted hydroxyl groups lead also to glycoside bond breaking besides the reaction of β-fragmentation and hydrolysis of radicals with an unpaired electron localized near C 1 , C 4 , C 5 aroms

Effets des extraits vegetaux sur la dynamique de populations des ...

African Journals Online (AJOL)

La présente étude se propose de trouver une alternative de l'utilisation des pesticides chimiques en testant l'effet insecticide des extraits aqueux des feuilles de Hyptis suaveolens, graines de Ricinus communis et de Azadirachta indica contre les ravageurs du niébé en conditions de champ en utilisant le cyperméthrine ...

La participation des femmes à la vie politique se traduit par des ...

International Development Research Centre (IDRC) Digital Library (Canada)

La participation des femmes à la vie politique se traduit par des économies locales plus vigoureuses. 08 juin 2016. Image. Des femmes assistent à une réunion d'un groupe d'entraide près d'. Edgard Rodriguez - IDRC. Des femmes assistent à une réunion d'un groupe d'entraide près d'Hyderabad, en Inde. Keenara ...

Incidence des prix et des taxes sur la consommation de produits du ...

International Development Research Centre (IDRC) Digital Library (Canada)

Incidence des prix et des taxes sur la consommation de produits du tabac en Argentine, en Bolivie et au Chili. Partout en Amérique du Sud, les adultes et les enfants font une grande consommation de tabac. Un nouveau projet de recherche se penchera sur les avantages et les limites des stratégies de fixation des prix et de ...

Roles et taches des accompagnateurs des patients hospitalises ...

African Journals Online (AJOL)

Roles et taches des accompagnateurs des patients hospitalises dans le service de pneumo-phtysiologie au Centre Hospitalier Universitaire Yalgado Ouedraogo de ... Logistical support represented by material support, drug supply, cleaning of premises, and littering occupied respectively 100%, 91%, 42% and 73%.

Oxime Ethers of (E)-11-Isonitrosostrychnine as Highly Potent Glycine Receptor Antagonists

DEFF Research Database (Denmark)

Mohsen, Amal M Y; Mandour, Yasmine M; Sarukhanyan, Edita

2016-01-01

of the crystal structure of the α3 glycine receptor indicated the same orientation of the strychnine core for all analogues. For the most potent oxime ethers, the ether substituent was accommodated in a lipophilic receptor binding pocket. The findings identify the oxime hydroxy group as a suitable attachment...

On the Optimal Thermal Management of Hybrid-Electric Vehicles with Heat Recovery Systems Sur le thermo-management optimal d’un véhicule électrique hybride avec un système de récupération de chaleur

Directory of Open Access Journals (Sweden)

Merz F.

2012-09-01

Full Text Available A general framework to combine optimal energy management (powertrain supervisory control and thermal management in Hybrid Electric Vehicles (HEV is presented. A HEV system with engine exhaust aftertreatment and exhaust heat recovery system is simulated under various scenarios, including warm and cold start. Optimal strategies are derived from Pontryagin Minimum Principle (PMP. The concept of fuel equivalent of thermal energy variations – similar to the equivalence factors for battery energy of standard Equivalent Consumption Minimization Strategy (ECMS – is introduced. The PMP-based strategies are compared with a heuristic, rule-based strategy. The benefits in fuel economy and reduction of pollutant emissions that are obtained for several scenarios are very promising. Une approche généralisée pour combiner la gestion de l’énergie (supervision du groupe motopropulseur et le thermo-management dans les véhicules hybrides électriques est proposée. Un système hybride incluant le post-traitement des polluants et un système de récupération de la chaleur à l’échappement du moteur thermique est simulé pour plusieurs scénarii, y compris le cas de départ à froid. Des stratégies de gestion de l’énergie optimales sont dérivées à partir du Principe de Minimum de Pontriaguine (PMP. Inspirée par les facteurs d’équivalence pour la consommation électrique que l’on retrouve dans la stratégie ECMS, la notion d’équivalent en carburant des flux d’énergie thermique est introduite. Les stratégies dérivées du PMP sont comparées avec une stratégie heuristique basée sur des règles. Les bénéfices en termes d’économies de carburant et réduction des émissions polluantes que l’on trouve pour différents scénarii sont encourageantes.

Nickel-catalyzed direct synthesis of dialkoxymethane ethers

Indian Academy of Sciences (India)

MURUGAN SUBARAMANIAN

Nickel catalysis; alcohol; paraformaldehyde; ether; solvent-free condition. 1. Introduction ..... oxidation and Dopamine Release with Protective Effects. Against Central ... P, Ghosh A, Saha R and Saha B 2016 A Review on the. Advancement of ...

Utilisation des mousses et des pâtes syntactiques pour combler les lacunes des poteries archéologiques

Directory of Open Access Journals (Sweden)

Viviane Bechoux

2008-10-01

Full Text Available Filling potteries missing parts with plaster raises now complex problems during the de-restoration treatments. Ceramics restorers have recurrently questions on the use of plaster in the field of archaeological ceramics restoration. Some researches point to the choice of other filling materials. At the present time other methods can be devised by proposing plaster replacement by a lightened composite material: syntactic foams and pastes.Le comblement des lacunes des poteries à partir du plâtre pose actuellement des problèmes complexes lors des traitements de dérestauration. Les restaurateurs de céramiques s'interrogent de manière récurrente sur l'utilisation du plâtre dans le domaine de la restauration des céramiques archéologiques. Des recherches s'orientent vers le choix d'autres matériaux d'obturation. Actuellement, d'autres méthodes peuvent être mises en place en proposant le remplacement du plâtre par un matériau composite allégé, les mousses et les pâtes syntactiques.

Développer le leadership dans des villes de l'Amérique latine et des ...

International Development Research Centre (IDRC) Digital Library (Canada)

Développer le leadership dans des villes de l'Amérique latine et des Caraïbes dans le contexte des changements climatiques. En raison des changements climatiques, de la croissance démographique et de l'urbanisation rapide non planifiée, les villes des pays en développement sont à la fois le principal déclencheur des ...

La Question de L'impunité des Auteurs de Violations des Droits de L'homme

Directory of Open Access Journals (Sweden)

Maria dos Remédios Fontes Silva

2010-10-01

Full Text Available Ce travail pretend faire reflechir à propos de la question de l'impunite des autorites de L'Etat face aux violations des droits de l'homme. On abordera cet egard: a le role de I'amnistie ble complicite des autoritesadministratives c la lenteur des procedures judicieuse.     L'analyse de cette question montre qui L'impunite des responsables des violations des droits de l'homme fait peser une menace sur I'ensemble du systeme de protection universelle des droits de l'homme.          On peut on conduire qu 'aucune societe que aspire à la democratie et ala justice ne peut se construire sur I'amoralite des crimes impunis et I'amnesie officielle.

Reproductive Effects of Two Polybrominated Diphenyl Ethers on the Rotifer Brachionus plicatilis.

Science.gov (United States)

Zhang, Jing; Wang, You; Zhou, Bin; Sun, Kai-Ming; Tang, Xuexi

2016-08-01

The effects of two polybrominated diphenyl ethers (PBDEs) on the reproduction of the rotifer Brachionus plicatilis were investigated. Results showed that sexual maturation was promoted by tetra-brominated diphenyl ether-47 (BDE-47) and deca-brominated diphenyl ether-209 (BDE-209), whereas fecundity was inhibited by BDE-47, but promoted by BDE-209. Additionally, both PBDEs affected the expression of two genes, vasa and nanos mRNA, related to rotifer reproduction. This suggests a possible regulatory molecular mechanism at the transcriptional level. Our research extends the current knowledge of the ecotoxicological mechanism induced by PBDEs and provides further essential information for assessing the risks of PBDE contamination in marine ecosystems.

Amended final report on the safety assessment of PPG-40 butyl ether with an addendum to include PPG-2, -4, -5, -9, -12, -14, -15, -16, -17, -18, -20, -22, -24, -26, -30, -33, -52, and -53 butyl ethers.

Science.gov (United States)

Lanigan, R S

2001-01-01

The Polypropylene Glycol (PPG) Butyl Ethers function as skinand hair-conditioning agents in cosmetics. Intestinal absorption of the PPG Butyl Ethers was inversely proportional to the molecular weight. In general, the toxicity of the PPG Butyl Ethers decreased as the molecular weight increased. In acute studies, moderate intraperitoneal (IP) doses of various PPG Butyl Ethers caused convulsive seizures in mice and anesthetized dogs, and large oral doses caused decreased activity, anuria, renal tubular swelling and necrosis, and hepatic swelling and necrosis. PPG-2 Butyl Ether vapors were nontoxic by the inhalation route. PPG-2 Butyl Ether was nontoxic in short-term feeding and dermal exposure studies in rats. In animal irritation studies, PPG-2 Butyl Ether caused minor, transient erythema and desquamation; in addition, erythema, edema, ecchymosis, necrosis, and other changes were observed during an acute percutaneous study. PPG-2 Butyl Ether also caused minor to moderate conjunctival irritation and minor corneal injury. PPG-2 Butyl Ether when dermally applied was nontoxic to pregnant rats and was nonteratogenic at doses up to 1.0 ml/kg/day. PPG BE800 at concentrations of 0.001% to 0.26% in feed was noncarcinogenic to rats after 2 years of treatment. In clinical studies, PPG BE800 was nonirritating and nonsensitizing to the skin when tested using 200 subjects. PPG-40 Butyl Ether was neither an irritant nor a sensitizer in a repeat-insult patch test using 112 subjects. Although clinical testing did not indicate significant skin irritation is produced by these ingredients, the animal test data did indicate the potential that these ingredients can be irritating. Therefore, it was concluded that the PPG Butyl Ethers can be used safely in cosmetic products if they are formulated to avoid irritation. Data on the component ingredients, Propylene Glycol, PPG, and n-Butyl Alcohol, from previous cosmetic ingredient safety assessments were also considered and found to support

Ether-Directed ortho-C–H Olefination with a PdII/MPAA Catalyst**

Science.gov (United States)

Li, Gang; Leow, Dasheng; Wan, Li; Yu, Jin-Quan

2013-01-01

Weak coordination is powerful! A PdII-catalyzed olefination of ortho-C–H bonds of arenes directed by weakly coordinating ethers is developed using mono-protected amino acid (MPAA) ligands. This finding provides a method for chemically modifying ethers, which are abundant in natural products and drug molecules. PMID:23239120

Photolytic degradation of polybromodiphenyl ethers under UV-lamp and solar irradiations

Energy Technology Data Exchange (ETDEWEB)

Shih, Yang-hsin, E-mail: yhs@nchu.edu.tw [Department of Soil and Environmental Sciences, National Chung Hsing University, Taichung 402, Taiwan (China); Wang, Chun-Kang [Department of Soil and Environmental Sciences, National Chung Hsing University, Taichung 402, Taiwan (China)

2009-06-15

Polybromodiphenyl ethers (PBDEs) are widely used flame retardant additives and have been mainly used in polymers for many plastic and electronic products. PBDEs have been found to bioaccumulate in both aquatic and terrestrial ecosystems and even human bodies. The technical product with the highest use is decabrominated diphenyl ether (BDE-209). Therefore, we chose to examine the solar and UV-lamp degradation of BDE-209. A linear increase of the photodegradation rate constant for BDE-209 was observed with the solar light intensity. The degradation reactions follow the pseudo-first-order kinetics. The photodegradation of BDE-209 produced other less brominated diphenyl ethers under ultraviolet light exposure, suggesting that the photodegradation of BDE-209 is a sequential dehalogenation mechanism. BDE-209 underwent rapid reductive debromination in these photodecomposition experiments. The formation rate constants of three nonabromodiphenyl ethers increase with the order of BDE-206, BDE-207 and BDE-208, indicating debromination mainly occurred at para > meta > ortho positions. These findings of the process properties and reductive debromination mechanism of the photolytic degradation of PBDEs can facilitate the design of remediation processes and also aid in predicting their fate in the environment.

Hydrolysis of strained bridgehead bicyclic vinyl ethers and sulfides

International Nuclear Information System (INIS)

Chwang, W.K.; Kresge, A.J.; Wiseman, J.R.

1979-01-01

Rates of hydrolysis of the bridgehead bicyclic vinyl ether 9-oxabicyclo[3.3.1]non-1-ene(6) and its vinyl sulfide counterpart 9-thiabicyclo[3.3.1]non-1-ene(7), catalyzed by the hydronium ion, were measured in H 2 O and in D 2 O solution. These data give isotope effects, k/sub H//k/sub D/ = 2.4 and 1.9 respectively, which show that these reactions occur by the normal, rate-determining carbon protonation, mechanism. The vinyl ether 6 is less reactive than its olefin analogue, bicyclo[3.3.1]non-1-ene (relative rate 1:1/1400), as may have been expected for a constrained bicyclic system such as this, where stabilization of the bridgehead carbocation intermediate by conjugation with oxygen is severely impaired. The vinyl sulfide 7, however, is even less reactive than the vinyl ether (relative rates 1:1/140); this is a remarkable result in view of the fact that conjugation between the sulfur atom and the cationic center is presumably also strongly inhibited. 1 figure, 3 tables

Membrane fluidization by alcohols inhibits DesK-DesR signalling in Bacillus subtilis.

Science.gov (United States)

Vaňousová, Kateřina; Beranová, Jana; Fišer, Radovan; Jemioła-Rzemińska, Malgorzata; Matyska Lišková, Petra; Cybulski, Larisa; Strzałka, Kazimierz; Konopásek, Ivo

2018-03-01

After cold shock, the Bacillus subtilis desaturase Des introduces double bonds into the fatty acids of existing membrane phospholipids. The synthesis of Des is regulated exclusively by the two-component system DesK/DesR; DesK serves as a sensor of the state of the membrane and triggers Des synthesis after a decrease in membrane fluidity. The aim of our work is to investigate the biophysical changes in the membrane that are able to affect the DesK signalling state. Using linear alcohols (ethanol, propanol, butanol, hexanol, octanol) and benzyl alcohol, we were able to suppress Des synthesis after a temperature downshift. The changes in the biophysical properties of the membrane caused by alcohol addition were followed using membrane fluorescent probes and differential scanning calorimetry. We found that the membrane fluidization induced by alcohols was reflected in an increased hydration at the lipid-water interface. This is associated with a decrease in DesK activity. The addition of alcohol mimics a temperature increase, which can be measured isothermically by fluorescence anisotropy. The effect of alcohols on the membrane periphery is in line with the concept of the mechanism by which two hydrophilic motifs located at opposite ends of the transmembrane region of DesK, which work as a molecular caliper, sense temperature-dependent variations in membrane properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Action des copolymères éthylène-acétate de vinyle sur la cinétique de nucléation et de croissance des n-paraffines n milieu hydrocarbure. Effect of Vinyl Ethyleneacetate Copolymers on the Nucleation and Growth Kinetics of N-Paraffins in a Hydrocarbon Medium.

Directory of Open Access Journals (Sweden)

Petinelli J. C.

2006-11-01

Full Text Available On cherche à mettre en évidence le mode d'action des copolymères éthylène-acétate de vinyle sur la cinétique de cristallisation des n-paraffines en milieu hydro-carbure. On s'attache, notamment, à déterminer si l'efficacité de ces additifs est peu ou prou influencée par le nombre de motifs non paraffiniques contenus dans leur chaîne.On décrit deux montages expérimentaux, l'un permettant d'étudier la cinétique de nucléation, l'autre la cinétique de croissance en solution. On observe, grâce à ces deux dispositifs, que la fréquence de germination tridimensionnelle et la vitesse de croissance des n-paraffines diminuent quand la concentration d'acétate de vinyle dans la solution augmente.On établit une relation entre le taux d'acétate de vinyle de la chaîne des copo-lymères et leur efficacité à retarder la cinétique de nucléation. La cinétique de croissance est discutée. On montre l'adsorption très forte de ces additifs sur les faces des cristaux et que le copolymère le plus riche en groupes acétate de vinyle est celui qui retarde le plus la cinétique de nucléation et de croissance des n- paraffines. An effort is made ta détermine how vinyl ethyleneacetate copolymers effect thé crystallization kinetics of n-paraffins in a hydrocarbon medium. In particular, research was done ta see if thé effectiveness of such additives is in thé least bit influenced by thé number of non-paraffinic patterns contained in their chain.Two expérimental assemblies are described, one for investigating nucléation kinetics, thé other growth kinetics in solution. These two devices are used ta observe thot thé theee-dimensional germination fréquency and growth rate of n-paraffins decrease as thé vinyl-acétate concentration in thé solution increases.A relationship is established between thé vinyl-acétate ratio of thé copolymer chain and thé effectiveness of thé copolymer in delaying thé nucléation kinetics. Growth kinetics

Photonique des Morphos

CERN Document Server

Berthier, Serge

2010-01-01

La photonique est déjà présente dans notre vie quotidienne, et on attend maintenant que la manipulation des photons permette aussi le traitement logique des informations. Cependant, l’élément de base qui permet cette manipulation de la lumière, le cristal photonique, est d’une réalisation complexe et mal contrôlée. Dans la course à la maîtrise de la lumière, les structures photoniques naturelles ont beaucoup à nous apprendre. C’est ce que nous montre Serge Berthier qui étudie dans ce livre la structure des écailles des Morphos. Tenant compte de l’essor récent des approches biomimétiques, il présente de manière détaillée plus de dix-huit techniques expérimentales utilisées pour ses analyses, ainsi que les diverses approches théoriques développées pour la modélisation de structures multi-échelles complexes. Première étude quasi-exhaustive des structures fines d’un genre et des propriétés optiques ainsi que colorimétriques générées, ce livre fournit aux entomologiste...

[Visualisation methods for etheric formative forces].

Science.gov (United States)

Burkhard, B; Kittel, R

2009-09-01

Rudolf Steiner, the founder of anthroposophy, suggested the development of visualisation methods for "etheric formative forces". The essential methods, their "spiritual scientific" basis and indications are described and their claims critically tested. The methods are not validated, the key criteria for diagnostic tests (reproducibility, sensitivity, specifity) are not given.

Screening phytochimique et identification spectroscopique des ...

African Journals Online (AJOL)

Origin

plante, effectuée pour la première fois, a révélé la présence des alcaloïdes, des flavonoïdes, des tanins catéchiques, des terpènes, des coumarines et des composés cyanogénétiques. Quant aux saponines et les quinones libres, ils sont présents chez les fleurs et absents chez les feuilles. La caractérisation des molécules.

Biosynthesis of ether-phospholipids including plasmalogens, peroxisomes and human disease: new insights into an old problem

NARCIS (Netherlands)

Wanders, Ronald J. A.; Brites, Pedro

2010-01-01

Ether-phospholipids represent an important subclass of phospholipids in animal cell membranes characterized by the presence of an ether bond at the sn-I position and the enrichment of PUFAs at the sn-2 position. Of the different ether-phospholipids, plasmalogens are the most abundant form and their

Convenient procedures for the α-metallation of vinylic ethers and thioethers

NARCIS (Netherlands)

Verkruijsse, H.D.; Brandsma, L.; Schleyer, P. von R.

1987-01-01

Ethyl vinyl ether H2C=CHOC2H5 and the analogous cyclic vinylic ethers dehydrofuran and 2,3-dihydropyran can be potassiated at −20°C in the α-position with a 1/1/1 molar mixture of BuLi, t-BuOK and TMEDA in hexane. Methyl vinyl sulfide is potassiated very smoothly by a 1/1 molar mixture of BuLi and

Etude du processus de changement vecu par des familles ayant decide d'adopter volontairement des comportements d'attenuation des changements climatiques

Science.gov (United States)

Leger, Michel T.

Les activites humaines energivores telles l'utilisation intensive de l'automobile, la surconsommation de biens et l'usage excessif d'electricite contribuent aux changements climatiques et autres problemes environnementaux. Bien que plusieurs recherches rapportent que l'etre humain est de plus en plus conscient de ses impacts sur le climat de la planete, ces memes recherches indiquent qu'en general, les gens continuent a se comporter de facon non ecologique. Que ce soit a l'ecole ou dans la communaute, plusieurs chercheurs en education relative a l'environnement estiment qu'une personne bien intentionnee est capable d'adopter des comportements plus respectueux de l'environnement. Le but de cette these etait de comprendre le processus d'integration de comportements d'attenuation des changements climatiques dans des familles. A cette fin, nous nous sommes fixe deux objectifs : 1) decrire les competences et les procedes qui favorisent l'adoption de comportements d'attenuation des changements climatiques dans des familles et 2) decrire les facteurs et les dynamiques familiales qui facilitent et limitent l'adoption de comportements d'attenuation des changements climatiques dans des familles. Des familles ont ete invitees a essayer des comportements personnels et collectifs d'attenuation des changements climatiques de sorte a integrer des modes de vie plus ecologiques. Sur une periode de huit mois, nous avons suivi leur experience de changement afin de mieux comprendre comment se produit le processus de changement dans des familles qui decident volontairement d'adopter des comportements d'attenuation des changements climatiques. Apres leur avoir fourni quelques connaissances de base sur les changements climatiques, nous avons observe le vecu de changement des familles durant huit mois d'essais a l'aide de journaux reflexifs, d'entretiens d'explicitation et du journal du chercheur. La these comporte trois articles scientifiques. Dans le premier article, nous presentons une

L'accumulation des métaux lourds au niveau des cultures : Cas des ...

African Journals Online (AJOL)

Le Bassin de Sebou présente une importance socio-économique pour le Maroc. En effet, il est sujet de diverses utilisations ; eau potable, eau d'irrigation et eau industrielle. Toutefois, ce bassin subit des pressions multiples, notamment par la pollution métallique. Considérant le risque de bioaccumulation des métaux par ...

The surface modifications of multi-walled carbon nanotubes for multi-walled carbon nanotube/poly(ether ether ketone) composites

International Nuclear Information System (INIS)

Cao, Zongshuang; Qiu, Li; Yang, Yongzhen; Chen, Yongkang; Liu, Xuguang

2015-01-01

Graphical abstract: Multi-walled carbon nanotube/poly(ether ether ketone) (MWCNT/PEEK) composites incorporating surface modified multi-walled carbon nanotubes (MWCNTs) as fillers were fabricated in a solution blending method in order to explore the dynamic mechanical and tribological properties of MWCNT/PEEK composites systematically. It is evident that surface modifications of MWCNTs have a significant impact on dispersibility of MWCNTs in PEEK, dynamic mechanical and tribological properties of MWCNT/PEEK composites. Typically, a clear effect of surface modifications of MWCNTs on tribological properties of MWCNT/PEEK composites was observed. A significant reduction in frictional coefficient of MWCNT/PEEK composites with the MWCNTs modified with ethanolamine has been achieved and the self-lubricating film on their worn surfaces was also observed. - Highlights: • The dispersibility of surface modified MWCNTs in PEEK has been studied. • MWCNTs modified with ethanolamine have showed a good dispersion in PEEK. • Surface modifications of MWCNTs have a significant impact on both dynamic mechanical and tribological properties of MWCNT/PEEK composites. - Abstract: The effects of surface modifications of multi-walled carbon nanotubes (MWCNTs) on the morphology, dynamic mechanical and tribological properties of multi-walled carbon nanotube/poly(ether ether ketone) (MWCNT/PEEK) composites have been investigated. MWCNTs were treated with mixed acids to obtain acid-functionalized MWCNTs. Then the acid-functionalized MWCNTs were modified with ethanolamine (named e-MWCNTs). The MWCNT/PEEK composites were prepared by a solution-blending method. A more homogeneous distribution of e-MWCNTs within the composites was found with scanning electron microscopy. Dynamic mechanical analysis demonstrated a clear increase in the storage modulus of e-MWCNT/PEEK composites because of the improved interfacial adhesion strength between e-MWCNTs and PEEK. Furthermore, the presence of e

The surface modifications of multi-walled carbon nanotubes for multi-walled carbon nanotube/poly(ether ether ketone) composites

Energy Technology Data Exchange (ETDEWEB)

Cao, Zongshuang [Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Research Center of Advanced Material Science and Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Qiu, Li [Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); College of Chemistry and Chemical Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Yang, Yongzhen, E-mail: yyztyut@126.com [Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Research Center of Advanced Material Science and Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Chen, Yongkang, E-mail: y.k.chen@herts.ac.uk [Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); University of Hertfordshire, School of Engineering and Technology, Hatfield, Hertfordshire AL10 9AB (United Kingdom); Liu, Xuguang [Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); College of Chemistry and Chemical Engineering, Taiyuan University of Technology, Taiyuan 030024 (China)

2015-10-30

Graphical abstract: Multi-walled carbon nanotube/poly(ether ether ketone) (MWCNT/PEEK) composites incorporating surface modified multi-walled carbon nanotubes (MWCNTs) as fillers were fabricated in a solution blending method in order to explore the dynamic mechanical and tribological properties of MWCNT/PEEK composites systematically. It is evident that surface modifications of MWCNTs have a significant impact on dispersibility of MWCNTs in PEEK, dynamic mechanical and tribological properties of MWCNT/PEEK composites. Typically, a clear effect of surface modifications of MWCNTs on tribological properties of MWCNT/PEEK composites was observed. A significant reduction in frictional coefficient of MWCNT/PEEK composites with the MWCNTs modified with ethanolamine has been achieved and the self-lubricating film on their worn surfaces was also observed. - Highlights: • The dispersibility of surface modified MWCNTs in PEEK has been studied. • MWCNTs modified with ethanolamine have showed a good dispersion in PEEK. • Surface modifications of MWCNTs have a significant impact on both dynamic mechanical and tribological properties of MWCNT/PEEK composites. - Abstract: The effects of surface modifications of multi-walled carbon nanotubes (MWCNTs) on the morphology, dynamic mechanical and tribological properties of multi-walled carbon nanotube/poly(ether ether ketone) (MWCNT/PEEK) composites have been investigated. MWCNTs were treated with mixed acids to obtain acid-functionalized MWCNTs. Then the acid-functionalized MWCNTs were modified with ethanolamine (named e-MWCNTs). The MWCNT/PEEK composites were prepared by a solution-blending method. A more homogeneous distribution of e-MWCNTs within the composites was found with scanning electron microscopy. Dynamic mechanical analysis demonstrated a clear increase in the storage modulus of e-MWCNT/PEEK composites because of the improved interfacial adhesion strength between e-MWCNTs and PEEK. Furthermore, the presence of e

Glycerol tertiary butyl ethers via etherification of glycerol with isobutene

Energy Technology Data Exchange (ETDEWEB)

Behr, A. [Dortmund Univ. (Germany). Chair of Chemical Process Development/Technical Chemistry A

2007-07-01

Glycerol and isobutene can react to a mixture of glycerol tertiary butyl ethers (GTBE) which can be used as additives for gasoline, diesel or biodiesel. This reaction was investigated in lab scale yielding a proposal for a process flow diagram containing reaction, extraction, flash and rectification units. This process has the advantages that only the suitable higher ethers are formed and that both glycerol and isobutene are fully converted. The homogeneous acid catalyst is low-priced and can be completely recycled. (orig.)

Contrôle des Circuits Auxiliaires des PFW (arrêt machines 2002/2003)

CERN Document Server

Ottaviani, J

2003-01-01

Les PFW sont des nappes polaires installées sur les pôles des aimants du PS. Elles sont au nombre de 4 par unité d aimant et constituées d un circuit principal (dans lequel circule le courant désiré selon le cycle magnétique utilisé) et de circuits auxiliaires. Les circuits auxiliaires sont des enroulements de correction (boucles de tour et pick-up brasés sur les enroulements). Pendant la variation du champ magnétique de l aimant PS, on utilise des tensions induites dans ces circuits auxiliaires pour corriger les erreurs de champ dues aux courants de Foucault dans la chambre à vide. Chaque année, pendant l arrêt machine, on vérifie si les caractéristiques des circuits auxiliaires correspondent aux normes (mesures des résistances des boucles de tours, résistances entre pick-up et isolation des circuits) afin de faire un suivi. Les 404 PFW sont ainsi vérifiées. Dans cette note, on ne relèvera que les PFW ayant des défauts (valeurs hors tolérances, boucles ouvertes ou en court-circuit, déf...

Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel

International Nuclear Information System (INIS)

Bensely, A.; Venkatesh, S.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.; Junik, Krzysztof

2008-01-01

The effect of cryogenic treatment on the distribution of residual stress in the case carburized steel (En 353) was studied using X-ray diffraction technique. Two types of cryogenic treatment: shallow cryogenic treatment (193 K) and deep cryogenic treatment (77 K) were adopted, as a supplement to conventional heat treatment. The amount of retained austenite in conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples was found to be 28%, 22% and 14%, respectively. The conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples in untempered condition had a surface residual stress of -125 MPa, -115 MPa and -235 MPa, respectively. After tempering the conventionally heat-treated, shallow cryogenically treated and deep cryogenically treated samples had a surface residual stress of -150 MPa, -80 MPa and -80 MPa, respectively. A comparative study of the three treatments revealed that there was an increase in the compressive residual stress in steel that was subjected to cryogenic treatment prior to tempering. The experimental investigation revealed that deep cryogenically treated steel when subjected to tempering has undergone a reduction in compressive residual stress. Such stress relieving behaviour was mainly due to the increased precipitation of fine carbides in specimens subjected to DCT with tempering

Biofilm behavior on sulfonated poly(ether-ether-ketone) (sPEEK)

Energy Technology Data Exchange (ETDEWEB)

Montero, Juan F.D. [Center for Research on Dental Implants (CEPID), School of Dentistry (ODT), Federal University of Santa Catarina - UFSC, Florianópolis, SC 88040-900 (Brazil); Tajiri, Henrique A.; Barra, Guilherme M.O.; Fredel, Márcio C. [Department of Mechanical Engineering (EMC), Federal University of Santa Catarina (UFSC), Florianópolis, SC 88040-900 (Brazil); Benfatti, Cesar A.M.; Magini, Ricardo S. [Center for Research on Dental Implants (CEPID), School of Dentistry (ODT), Federal University of Santa Catarina - UFSC, Florianópolis, SC 88040-900 (Brazil); Pimenta, Andréa L. [Integrated Laboratories Technologies (InteLAB), Dept. Chemical Engineering (EQA), Federal University of Santa Catarina - UFSC, Florianópolis, SC 88040-970 (Brazil); Department of Biologie, Université de Cergy Pontoise, 2, Av. Adolphe Chauvin, 95302 Cergy Pontoise (France); Souza, Júlio C.M., E-mail: julio.c.m.souza@ufsc.br [Center for Research on Dental Implants (CEPID), School of Dentistry (ODT), Federal University of Santa Catarina - UFSC, Florianópolis, SC 88040-900 (Brazil); Center for Microelectromechanical Systems (CMEMS), Dept. Mechanical Engineering (DEM), Campus Azurém, 4800-058 Guimarães (Portugal)

2017-01-01

Poly(ether-ether-ketone) (PEEK) has also shown to be very attractive for incorporating therapeutic compounds thanks to a sulfonation process which modifies the material structure resulting in a sulfonated-PEEK (sPEEK). Concerning biomedical applications, the objective of this work was to evaluate the influence of different sulfonation degree of sPEEK on the biofilm growth. PEEK samples were functionalized by using sulphuric acid (98%) and then dissolved into dimethyl-sulfoxide. A dip coating technique was used to synthesize sPEEK thin films. The sulfonation degree of the materials was analyzed by FT-IR, H NMR, TG and IEC. The surfaces were characterized by scanning electron microscopy, profilometry and contact angle analyses. Subsequently, the biofilm formation on sulfonated-PEEK based on Streptococcus mutans and Enterococcus faecalis was measured by spectrophotometry, colony forming units (CFU mL{sup −1}) and SEM. Results obtained from thermal and chemical analyses showed an intensification in sulfonation degree for sPEEK at 2 and 2.5 h. The E. faecalis or S. mutans biofilm growth revealed statistically significant differences (p < 0.05) between 2 and 3 h sulfonation groups. A significant decrease (p < 0.05) in CFU mL{sup −1} was recorded for S. mutans or E. faecalis biofilm grown on 2.5 or 3 h sPEEK. Regarding the thermal-chemical and microbiologic analyses, the sulfonation degree of sPEEK ranging from 2 up to 3 h was successful capable to decrease the biofilm growth. That revealed an alternative strategy to embed anti-biofilm and therapeutic compounds into PEEK avoiding infections in biomedical applications. - Highlights: • PEEK can be dissolved to incorporate therapeutic compounds. • High sulfonation degree on sPEEK affected the biofilm growth. • The sulfonation degree must be controlled to maintain the properties of sPEEK.

Biofilm behavior on sulfonated poly(ether-ether-ketone) (sPEEK)

International Nuclear Information System (INIS)

Montero, Juan F.D.; Tajiri, Henrique A.; Barra, Guilherme M.O.; Fredel, Márcio C.; Benfatti, Cesar A.M.; Magini, Ricardo S.; Pimenta, Andréa L.; Souza, Júlio C.M.

2017-01-01

Poly(ether-ether-ketone) (PEEK) has also shown to be very attractive for incorporating therapeutic compounds thanks to a sulfonation process which modifies the material structure resulting in a sulfonated-PEEK (sPEEK). Concerning biomedical applications, the objective of this work was to evaluate the influence of different sulfonation degree of sPEEK on the biofilm growth. PEEK samples were functionalized by using sulphuric acid (98%) and then dissolved into dimethyl-sulfoxide. A dip coating technique was used to synthesize sPEEK thin films. The sulfonation degree of the materials was analyzed by FT-IR, H NMR, TG and IEC. The surfaces were characterized by scanning electron microscopy, profilometry and contact angle analyses. Subsequently, the biofilm formation on sulfonated-PEEK based on Streptococcus mutans and Enterococcus faecalis was measured by spectrophotometry, colony forming units (CFU mL −1 ) and SEM. Results obtained from thermal and chemical analyses showed an intensification in sulfonation degree for sPEEK at 2 and 2.5 h. The E. faecalis or S. mutans biofilm growth revealed statistically significant differences (p < 0.05) between 2 and 3 h sulfonation groups. A significant decrease (p < 0.05) in CFU mL −1 was recorded for S. mutans or E. faecalis biofilm grown on 2.5 or 3 h sPEEK. Regarding the thermal-chemical and microbiologic analyses, the sulfonation degree of sPEEK ranging from 2 up to 3 h was successful capable to decrease the biofilm growth. That revealed an alternative strategy to embed anti-biofilm and therapeutic compounds into PEEK avoiding infections in biomedical applications. - Highlights: • PEEK can be dissolved to incorporate therapeutic compounds. • High sulfonation degree on sPEEK affected the biofilm growth. • The sulfonation degree must be controlled to maintain the properties of sPEEK.

Radium separation through complexation by aqueous crown ethers and ion exchange or solvent extraction

Energy Technology Data Exchange (ETDEWEB)

Chiarizia, R.; Dietz, M.L.; Horwitz, E.P. [Argonne National Lab., IL (United States). Chemistry Div.; Burnett, W.C. [Florida State Univ., Tallahassee, FL (United States). Dept. of Oceanography

1997-11-01

The effect of three water-soluble, unsubstituted crown ethers (15-crown-5 (15C5), 18-crown-6 (18C6) and 21-crown-7 (21C7)) on the uptake of Ca, Sr, Ba and Ra cations by a sulfonic acid cation exchange resin, and on the extraction of the same cations by xylene solutions of dinonylnaphthalenesulfonic acid (HDNNS) from aqueous hydrochloric acid solutions has been investigated. The crown ethers enhance the sorption of the larger cations by the ion exchange resin, thereby improving the resin selectivity over calcium, a result of a synergistic interaction between the crown ether and the ionic functional groups of the resin. Similarly, the extraction of the larger alkaline earth cations into xylene by HDNNS is strongly synergized by the presence of the crown ethers in the aqueous phase. Promising results for intra-Group IIa cation separations have been obtained using each of the three crown ethers as the aqueous ligands and the sulfonic acid cation exchange resin. Even greater separation factors for the radium-calcium couple have been measured with the crown-ethers and HDNNS solutions in the solvent extraction mode. The application of the uptake and extraction results to the development of radium separation schemes is discussed and a possible flowchart for the determination of {sup 226}Ra/{sup 228}Ra in natural waters is presented.

[Ether Day--no laughing matter. The birth of modern anaesthesia].

Science.gov (United States)

Goerig, Michael; Wulf, Hinnerk

2013-10-01

Since centuries the first public demonstration of the anaesthetic properties of ether by William Thomas Green Morton at the Massachusetts General Hospital in Boston on October 16th 1846 is celebrated as "Ether Day" world-wide. The news of the beneficial effects, primarily disposed as a "Yankee Invention", spread over all continents quickly. This was the result of an article, published in the Boston Medical and Surgical Journal on November 18th, 1846. It is mentioning worth that this article was written when Morton had disclosed that the used "preparation", later named as "Nostrum" or "Letheon", was sulphuric ether. The important discovery later became a patent case and was overshadowed by a long lasting priority claim. Nevertheless the readers of the New England Journal of Medicine voted in a survey that this article was the most important publication in the 200 years journals history ever. © Georg Thieme Verlag Stuttgart · New York.

Designing of molecular architecture, synthesis and properties of the next generation of state-of-the-art high-performance thermoplastic fluoro-poly(ether amide)s, (6F-PEA), fluoro-poly(ether amide-imide)s (6F-PEAI), and their co-polymers

International Nuclear Information System (INIS)

Vora, Rohitkumar H.

2010-01-01

Graphical abstract: Molecular architectures of next generation of high-performance advanced heat stable thermoplastic polymer compositions of fluoro-poly(ether amide) (6F-PA) and fluoro-poly(ether amide-imide) (6F-PEAI) having di-ether diamines moieties were designed based on fluoro-polyimide (6F-PI) chemistry, and polymers were synthesized using two novel state-of-the-art 2-(3,4'-carboxy anhydrophenyl-2(4-carboxyphenyl) hexafluoropropane (6FTMA) and 2,2'-bis(4-carboxyphenyl) hexafluropropane (6F-DAc) monomers. Their copolymers: fluoro-copoly(ether amide-(ether imide))s (6F-co(PEA-PEI)), fluoro-copoly(ether amide-(ether amide-imide))s (6F-co(PEA-PEAI)) and fluoro-copoly(ether amide-imide-(ether imide))s (6F-co(PEAI-PEI)) were also designed and synthesized using 2,2'-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydrides (6FDA) for the advanced aerospace, defense and industrial engineering applications. -- Abstract: A new generation of high-performance polymers for the advanced industrial, aerospace and defense engineering applications are being investigated in the academic and industrial research institutions throughout the world. Fluoro-polyimides (6F-PI) are one such sub-class of high-performance polyimide polymers. In the last 25 years a number of fluoro-polyimides have been reported but only a handful of them have been commercialized. This paper describes the 6F-polyimide chemistry-based designed molecular architectures and synthesis of two series of next generation of heat stable thermoplastic polymer compositions having di-ether diamines moieties, such as fluoro-poly(ether amide) (6F-PA) and fluoro-poly(ether amide-imide) (6F-PEAI) using the novel state-of-the-art 2-(3,4'-carboxy anhydrophenyl-2(4-carboxyphenyl) hexafluoropropane (6F-TMA) and 2,2'-bis(4-carboxyphenyl) hexafluoropropane (6F-DAc) monomers. Their co-polymers: fluoro-copoly(ether amide-(ether imide))s (6F-co(PEA-PEI)), fluoro-copoly(ether amide-(ether amide-imide))s (6F-co(PEA-PEAI)) and fluoro-copoly(ether

Potenciales zeta del algodón en presencia de la mezcla de tensioactivos LAS (aniónico) con alquilpoliglucósido (no iónico)

OpenAIRE

Carrión Fité, Francisco Javier

2007-01-01

Dans le but d'obtenir de bons niveaux de biodegradabilité et de toxicité dans les produits tensioactifs, les alquilpolyglucosides sont apparus dans le marché. Ces tensioactifs non ioniques, obtenus à partir de substances naturelles, sont 100% biodégradables et sont très intéressants pour son application dans le lavage. La double cape électrique du tissu, caractérisée comme potentiel zêta, est un paramètre influent dans la déposition d'impuretés sur le même, pendant le lavage. Par conséquent s...

Contribution des TICs à l'abandon des mutilations génitales ...

International Development Research Centre (IDRC) Digital Library (Canada)

Contribution des TIC à l'abandon des MGF en Afrique de l'Ouest francophone : rôle des jeunes citoyennes; rapport technique no. 5 (rapport technique final), 18 octobre 2008 - 31 mars 2009. Download PDF. Related content. New website will help record vital life events to improve access to services for all. A new website ...

utilisation des donnees pour l'evaluation de l'heterogeneite des sols

African Journals Online (AJOL)

AISA

étude a permis de caractériser l'hétérogénéité des sols ferrallitiques, à travers sa couleur. Mots-clés : Couleur ... ainsi qu'à l'application des recommandations des doses de fertilisant. ..... de « système sol » en zone de contact forêt- savane du ...

Modeling of a Reaction-Distillation-Recycle System to Produce Dimethyl Ether through Methanol Dehydration

Science.gov (United States)

Muharam, Y.; Zulkarnain, L. M.; Wirya, A. S.

2018-03-01

The increase in the dimethyl ether yield through methanol dehydration due to a recycle integration to a reaction-distillation system was studied in this research. A one-dimensional phenomenological model of a methanol dehydration reactor and a shortcut model of distillation columns were used to achieve the aim. Simulation results show that 10.7 moles/s of dimethyl ether is produced in a reaction-distillation system with the reactor length being 4 m, the reactor inlet pressure being 18 atm, the reactor inlet temperature being 533 K, the reactor inlet velocity being 0.408 m/s, and the distillation pressure being 8 atm. The methanol conversion is 90% and the dimethyl ether yield is 48%. The integration of the recycle stream to the system increases the dimethyl ether yield by 8%.

Developments in Spray Modeling in Diesel and Direct-Injection Gasoline Engines Progrès de la modélisation des sprays dans les moteurs Diesel et à essence

Directory of Open Access Journals (Sweden)

Kong S. C.

2006-12-01

Full Text Available In direct-injection engines, the fuel spray characteristics influence the combustion efficiency and exhaust emissions. The performance of available spray models for predicting liquid and vapor fuel distributions, and their influence on combustion is reviewed for both diesel and gasoline direct injection engines. A phenomenological nozzle flow model is described for simulating the effects of diesel injector nozzle internal geometry on the fuel injection and spray processes. The flow model provides initial conditions for the liquid jet breakup model that considers wave instabilities due to Kelvin-Helmholtz (KH and Rayleigh-Taylor (RT mechanisms. A linearized instability analysis has also been extended to consider the breakup of liquid sheets for modeling pressure-swirl gasoline injectors. Diesel engine predictions have been compared with extensive data from in-cylinder laser diagnostics carried out in optically accessible heavy-duty, DI Diesel engines over a wide range of operating conditions. The results show that the nozzle flow model used in combination with the KH and RT models gives realistic spray predictions. In particular, the limited liquid fuel penetration length observed experimentally and the flame shape details are captured accurately. The liquid sheet breakup model has also been compared favorably with experimental spray penetration and drop size data for gasoline hollow-cone sprays. This model is currently being applied to study stratified charge combustion in GDI engines. Dans les moteurs à injection directe, les caractéristiques du spray de carburant influent directement sur le rendement et les émissions. Les performances des modèles de spray existants et leur influence sur la combustion pour les moteurs Diesel et essence à injection directe sont analysées. Un modèle phénoménologique d'écoulement dans les injecteurs indiquant les effets de la géométrie sur les processus d'injection est présenté. Ce modèle donne les

40 CFR 721.6980 - Dimer acids, polymer with polyalkylene glycol, bisphenol A-diglycidyl ether, and alky-lenepolyols...

Science.gov (United States)

2010-07-01

... reporting. (1) The chemical substance dimer acids, polymer with polyalkylene glycol, bisphenol A-diglycidyl... glycol, bisphenol A-diglycidyl ether, and alky-lenepolyols polyglycidyl ethers (generic name). 721.6980... Substances § 721.6980 Dimer acids, polymer with polyalkylene glycol, bisphenol A-diglycidyl ether, and alky...

Les lexiques des jeunes dans les discours écrits des blogs : pour une approche descriptive

Directory of Open Access Journals (Sweden)

Lorenz Paulina

2014-07-01

Full Text Available S’il ne faut pas confondre ce qui est appelé communément « langage SMS » et « langage des jeunes », nous avancerons toutefois que les pratiques langagières écrites des jeunes sur les supports modernes de communication, et notamment dans les blogs, présentent des particularités encore peu étudiées. Les traits observables les plus saillants sont ceux de la morphologie graphique, mais il n’en reste pas moins que certains jeunes utilisent des lexiques particuliers dans les blogs qui méritent une attention particulière. Nous nous proposons donc d’étudier les différents lexiques utilisés par des jeunes de 12 à 22 ans dans les blogs de la plateforme skyrock.com aux niveaux de sa diversité, de ses usages sémantiques variable d’un scripteur à l’autre pour un même mot, et de ses particularités morphosyntaxiques. En effet, nous observerons des lexiques divers allant des lexiques perçus comme relevant des cités à des lexiques perçus comme étant « branchés-jeunes », ou encore à des lexiques propres aux supports modernes de communication. Ainsi, nous analyserons des lexiques variés dans leurs usages écrits tels que bolos, bédave, gérer, ouf, tigen, ou encore des lexiques empruntés tels que mouv, full, etc., ainsi que des emplois particuliers de séquences autonomes comme lol. Quelques questions périphériques complèteront notre analyse telle que celles qui concerne l’influence des usages lexicaux entre pairs et le savoir partagé, la distinction de différentes communautés en fonction des lexiques utilisés, ou encore la variabilité des représentations graphiques d’un même mot.

Assessment of ether and alcohol fuels from coal. Volume 2. Technical report

Energy Technology Data Exchange (ETDEWEB)

1983-03-01

A unique route for the indirect liquefaction of coal to produce transportation fuel has been evaluated. The resultant fuel includes alkyl tertiary alkyl ethers and higher alcohols, all in the gasoline boiling range. When blended into gasoline, the ether fuel provides several advantages over the lower alcohols: (1) lower chemical oxygen content, (2) less-severe water-separation problems, and (3) reduced front-end volatility effects. The ether fuel also has high-octane quality. Further, it can be utilized as a gasoline substitute in all proportions. Production of ether fuel combines several steps, all of which are or have been practiced on an industrial scale: (1) coal gasification, (2) gas cleanup and shift to desired H/sub 2/:CO ratio, (3) conversion of synthesis gas to isobutanol, methanol, and higher alcohols, (4) separation of alcohols, (5) chemical dehydration of isobutanol to isobutylene, and (6) etherification of isobutylene with methanol. A pilot-plant investigation of the isobutanol synthesis step was performed. Estimates of ether-fuel manufacturing costs indicate this process route is significantly more costly than synthesis of methanol. However, the fuel performance features provide incentive for developing the necessary process and catalyst improvements. Co-production of higher-molecular-weight co-solvent alcohols represents a less-drastic form of methanol modification to achieve improvement in the performance of methanol-gasoline blends. Costs were estimated for producing several proportions of methanol plus higher alcohols from coal. Estimated fuel selling price increases regularly but modestly with higher alcohol content.

Contrôle des circuits auxiliaires des P.F.W. (arret machine 2004/2006)

CERN Document Server

Ottaviani, J

2005-01-01

Les PFW sont des nappes polaires installées sur les pôles des aimants du PS. Elles sont au nombre de 4 par unité d’aimant et constituées d’un circuit principal (dans lequel circule le courant désiré selon le cycle magnétique utilisé) et de circuits auxiliaires. Les circuits auxiliaires sont des enroulements de correction (boucles de tour et “pick-up” brasés sur les enroulements principaux). Pendant la variation du champ magnétique de l’aimant PS, on utilise des tensions induites dans ces circuits auxiliaires pour corriger les erreurs de champ dues aux pertes par courants de Foucault dans la chambre à vide. Chaque année, pendant l’arrêt machine, on vérifie si les caractéristiques des circuits auxiliaires correspondent aux normes (mesures des résistances des boucles de tours, résistances entre “pick-up” et isolation des circuits) afin de faire un suivi. Les 404 PFW sont ainsi vérifiées. Dans cette note, on ne relèvera que les PFW ayant des défauts (valeurs hors tolérances, ...

SYNTHESIS OF ALLYL PHENYL ETHER AND CLAISEN REARRANGEMENT

Directory of Open Access Journals (Sweden)

Gagik Torosyan

2011-12-01

Full Text Available It has been established the possibility for phenol allylation on natural zeolites and them analogs. Here is demonstrated the synthesis of allyl phenol, which has wide industrial applications. The offered method in comparison with the traditional methods has more advantages – higher selectivity, smaller material and power resources consumption. It has been obtained the mixture of allylating phenols (30% in general with allyl phenyl ether (1 with 80% yields. At 600 K is obtained allylphenyl ether, at 700 K beginning the formation of allyl phenols, which is the result of direct C-allylation of the aromatic ring. It has been investigated the possibility of Claisen rearrangement in the same conditions. All of that are established by gas-liquid chromatography and liquid chromatography data.

Ether in Kant and akasa in Prasastapada: Philosophy in comparative perspective

Directory of Open Access Journals (Sweden)

Fernando Tola

2015-02-01

Full Text Available The study of Indian and Western systems of Philosophy reveals many points of thematic and methodological coincidences between them. We have collected a good number of these coincidences in our recent books, where we have included many philosophical texts in Sanskrit and in European languages which contain the expression of astonishing similar ideas and theses. In the present article we add a new instance of coincidence between Indian and Western thought in relation to akasa in India (limited to the Indian philosophical system Vaisesika and ether (Aether or Äther in German in the Opus postumum of Kant. The inexistence of both akasa and ether has been established by Modern Science. Akasa and ether in India and the West, respectively, constitute a notorious example of asrayasiddha, the well-known logical defect considered by Indian Logic.

Etat des lieux des soins de premier recours des malades mentaux à Antananarivo : étude rétrospective

Science.gov (United States)

Bakohariliva, Hasina Andrianarivony; Rafehivola, Imisanavalona Hanitrinihaja; Raobelle, Evah Norotiana; Raharivelo, Adeline; Rajaonarison, Bertille Hortense

2018-01-01

Résumé Religion et guérisseurs traditionnels occupent encore une place prépondérante dans la prise en charge des maladies mentales à Madagascar. Ainsi, nous nous sommes fixés comme objectif d'établir un état des lieux sur les soins de premier recours des malades mentaux. Nous avons mené une étude rétrospective descriptive s'étalant sur une période de 16 mois allant de janvier 2014 en avril 2015 au sein du service de psychiatrie du CHU de Befelatanana à Antananarivo. La prévalence des psychoses était de 25%. Le genre féminin (53%), l'ethnie merina (77%), les étudiants (45%), le niveau d'étude secondaire (40%), les célibataires (72%), la religion protestante (45%), ainsi que le niveau socio-économique moyen (57,5%) étaient prédominants. Dans les paramètres cliniques, le mode de début brutal (52%), le premier recours à la religion (40%), la présence d'antécédents des cas similaire (90%), étaient majoritaires. La schizophrénie était la pathologie la plus rencontrée dans la moitié des cas. Le délai d'amélioration en cas de traitement religieux et traditionnels était dans la moitié des cas de plus de 10 jours d'hospitalisation. Les patients ayant reçu une prise en charge psychiatrique en premier recours, étaient améliorés dans 75 % cas en moins de 10jours. Le retard du recours aux soins psychiatriques est une réalité à Madagascar qui aggrave le pronostic des psychoses. PMID:29632623

Selective crystallization of cations with crown ethers; Selektive Kristallisation von Kationen mit Kronenethern

Energy Technology Data Exchange (ETDEWEB)

Heffels, Dennis Egidius

2014-07-04

The aim of this work was to study the selectivity and preferences of the incorporation of differently sized cations in the cavities of various crown ethers and the characterization of the resulting compounds. The coordination preferences of crown ethers with different cavities have long been known, and the impact of other effects on the structure formation have increasingly become the focus of attention. In this work a comparative overview of the coordination preferences depending on various factors was undertaken. The focus was mainly on the variation of the cavity of the crown ether in the presence of differently sized cations. In addition, the effects of the solvent and differently coordinating anions have been investigated. Within the framework of this work, basic coordination preferences could be detected with rare earth nitrates, which are affected particularly by the choice of the solvent. The formation of different types of structures could be controlled by varying the conditions such that the incorporation of the cation in the cavity of the crown ether was influenced and the formation of a particular type of structure can be influenced partly by the choice of solvent. In this case no direct preferences for the incorporation into the cavity of the crown ether in relation to the cation size were observed for rare earth cations. However, the coordination of the crown ether leads in each case - for lanthanides - to rather high coordination numbers. A total of five new rare earth complexes and two structural variants could be observed with crown ethers. In the study of the selectivity of the incorporation into the cavity, known structures were also reproduced and further structures were characterized but the crystal structures not entirely solved. With the use of monovalent cations such as potassium, lithium or silver a total of nine new compounds could be synthesized, while no clear preferences for the incorporation of certain cations were detected. The

Chemical Composition and Cytotoxic Activities of Petroleum Ether ...

African Journals Online (AJOL)

Methods: The composition of petroleum ether extract was analyzed by gas ... acids, sterides, pregnanones, terpenes, alkaloids, alkenes, alcohols, ketones, aldehydes and other compounds. .... and mass spectra with those obtained from the.

Photodegradation of poly(ether sulphone). Part 2

DEFF Research Database (Denmark)

Norrman, K.; Krebs, Frederik C

2004-01-01

The photodegradation of poly(ether sulphone) (PES) was investigated systematically by time-of-flight SIMS (ToF-SIMS) and x-ray photoelectron spectroscopy (XPS). The effect of varying the irradiation dose, wavelength and the atmosphere was studied along with mechanistic photooxidation studies using...

40 CFR 721.7000 - Polymer of disodium maleate, allyl ether, and ethylene oxide.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polymer of disodium maleate, allyl... New Uses for Specific Chemical Substances § 721.7000 Polymer of disodium maleate, allyl ether, and... substance identified generically as a polymer of disodium maleate, allyl ether, and ethylene oxide (P-91...

Gold-catalyzed intermolecular coupling of sulfonylacetylene with allyl ethers: [3,3]- and [1,3]-rearrangements

Directory of Open Access Journals (Sweden)

Jungho Jun

2013-08-01

Full Text Available Gold-catalyzed intermolecular couplings of sulfonylacetylenes with allyl ethers are reported. A cooperative polarization of alkynes both by a gold catalyst and a sulfonyl substituent resulted in an efficient intermolecular tandem carboalkoxylation. Reactions of linear allyl ethers are consistent with the [3,3]-sigmatropic rearrangement mechanism, while those of branched allyl ethers provided [3,3]- and [1,3]-rearrangement products through the formation of a tight ion–dipole pair.

Evaluation of hepatic biotransformation of polybrominated diphenyl ethers in the polar bear (Ursus maritimus).

Science.gov (United States)

Krieger, Lisa K; Szeitz, András; Bandiera, Stelvio M

2016-03-01

Polar bears are at the top of the Arctic marine food chain and are subject to exposure and bioaccumulation of environmental chemicals of concern such as polybrominated diphenyl ethers (PBDEs), which were widely used as flame retardants. The aim of the present study was to evaluate the in vitro oxidative metabolism of 2,2',4,4'-tetrabrominated diphenyl ether (BDE-47) and 2,2',4,4',5-pentabrominated diphenyl ether (BDE-99) by polar bear liver microsomes. The identification and quantification of the hydroxy-brominated diphenyl ethers formed were assessed using an ultra-high performance liquid chromatography-tandem mass spectrometry-based method. Incubation of BDE-47 with archived individual liver microsomes, prepared from fifteen polar bears from northern Canada, produced a total of eleven hydroxylated metabolites, eight of which were identified using authentic standards. The major metabolites were 4'-hydroxy-2,2',4,5'-tetrabromodiphenyl ether and 5'-hydroxy-2,2',4,4'-tetrabromodiphenyl ether. Incubation of BDE-99 with polar bear liver microsomes produced a total of eleven hydroxylated metabolites, seven of which were identified using authentic standards. The major metabolites were 2,4,5-tribromophenol and 4-hydroxy-2,2',3,4',5-pentabromodiphenyl ether. Among the CYP specific antibodies tested, anti-rat CYP2B was found to be the most active in inhibiting the formation of hydroxylated metabolites of both BDE-47 and BDE-99, indicating that CYP2B was the major CYP enzyme involved in the oxidative biotransformation of these two congeners. Our study shows that polar bears are capable of forming multiple hydroxylated metabolites of BDE-47 and BDE-99 in vitro and demonstrates the role of CYP2B in the biotransformation and possibly in the toxicity of BDE-47 and BDE-99 in polar bears. Copyright © 2015 Elsevier Ltd. All rights reserved.

Accès à l'eau : des solutions techniques et sociales aident des ...

International Development Research Centre (IDRC) Digital Library (Canada)

Grâce à la modélisation par ordinateur faisant appel à des techniques de pointe et à la consultation des collectivités, l'organisme bolivien Agua Sustentable a trouvé des solutions politiques à des conflits qui auraient pu s'avérer désastreux au sujet de l'accès à l'eau. Cet organisme de recherche subventionné par le CRDI a ...

Le Débat des semences

International Development Research Centre (IDRC) Digital Library (Canada)

Solutions pour les lois nationales régissant le contrôle des ressources génétiques et des ...... des pouvoirs) qui reconnaissent, dans une certaine mesure, les droits de gestion collectifs des ...... documentés, les performances physiques, etc.

Stress shielding and fatigue limits of poly-ether-ether-ketone dental implants.

Science.gov (United States)

Lee, Woo-Taek; Koak, Jai-Young; Lim, Young-Jun; Kim, Seong-Kyun; Kwon, Ho-Beom; Kim, Myung-Joo

2012-05-01

The poly-ether-ether-ketone (PEEK) polymer is of great interest as an alternative to titanium in orthopedics because of its biocompatibility and low elastic modulus. This study evaluated the fatigue limits of PEEK and the effects of the low elastic modulus PEEK in relation to existing dental implants. Compressive loading tests were performed with glass fiber-reinforced PEEK (GFR-PEEK), carbon fiber-reinforced PEEK (CFR-PEEK), and titanium rods. Among these tests, GFR-PEEK fatigue tests were performed according to ISO 14801. For the finite element analysis, three-dimensional models of dental implants and bone were constructed. The implants in the test groups were coated with a 0.5-mm thick and 5-mm long PEEK layer on the upper intrabony area. The strain energy densities (SED) were calculated, and the bone resorption was predicted. The fatigue limits of GFR-PEEK were 310 N and were higher than the static compressive strength of GFR-PEEK. The bone around PEEK-coated implants showed higher levels of SED than the bone in direct contact with the implants, and the wider diameter and stiffer implants showed lower levels of SED. The compressive strength of the GFR-PEEK and CFR-PEEK implants ranged within the bite force of the anterior and posterior dentitions, respectively, and the PEEK implants showed adequate fatigue limits for replacing the anterior teeth. Dental implants with PEEK coatings and PEEK implants may reduce stress shielding effects. Dental implant application of PEEK polymer-fatigue limit and stress shielding. Copyright © 2012 Wiley Periodicals, Inc.

Performances de ponte et qualité des oeufs des poules pondeuses ...

African Journals Online (AJOL)

Les performances de ponte et la qualité des oeufs de 216 poules pondeuses ISA Brown âgées de 21 semaines ont été déterminées en les alimentant avec des rations contenant des feuilles séchées de manioc (Manihot esculenta, Crantz). Pendant douze semaines, trois groupes de 72 poules chacun (réparties en trois ...

Freins et leviers à la diversification des cultures : étude au niveau des exploitations agricoles et des filières

Directory of Open Access Journals (Sweden)

Meynard Jean-Marc

2013-07-01

Full Text Available La diversification des cultures est souvent présentée comme un levier d’action pour accroître la durabilité des systèmes de production agricoles. Bien raisonnée, elle favorise en effet une réduction de l’usage d’intrants extérieurs à l’exploitation – pesticides, engrais, eau – et des nuisances environnementales associées à leur utilisation excessive. À l’inverse, la simplification des systèmes de culture engagée depuis plus de 40 ans s’est accompagnée d’un recours croissant aux intrants. Cependant, malgré son intérêt pour les systèmes de production en termes de durabilité écologique mais aussi économique (répartition des risques, et son inscription dans divers plans et dispositifs incitatifs, la diversification des cultures progresse peu. Les ministères en charge de l’agriculture et de l’environnement ont donc commandé à l’INRA une étude visant à identifier les freins à la diversification des cultures en France et les leviers mobilisables, par les pouvoirs publics notamment, pour la favoriser. L’hypothèse de travail est que ces freins relèvent du fonctionnement global du système agro-industriel, et de la capacité de développement de filières valorisant les cultures de diversification. L’étude a examiné un certain nombre de cas représentatifs de la diversité des filières et notamment de leurs modes d’organisation, qui déterminent la coordination et l’engagement des acteurs économiques impliqués dans le développement d’une culture de diversification.

Impact écotoxicologique de mélanges de pesticides sur des fonctions microbiennes des sols : apport d’une prise en compte écologique dans l’évaluation des risques

OpenAIRE

Devers-Lamrani, Marion; Rouard, Nadine; Cheviron, Nathalie; Grondin, Virginie; Martin-Laurent, Fabrice

2015-01-01

L’utilisation de pesticides permet d’assurer la qualité de la production végétale mais elle contribue à la contamination des sols et des eaux et produit des effets sur des organismes noncibles. L’évaluation des risques requièrent actuellement une meilleure prise en compte des effets des pesticides sur le fonctionnement des écosystèmes. Or, les démarches et indicateurs classiques manquent de représentativité écologique. La fonction microbienne de biodégradation des pesticides est essentielle c...

Mesure de la masse volumique des particules des eaux résiduaires urbaines : protocole et évaluation des incertitudes

OpenAIRE

RUBAN, Gwenaël; LABORATOIRE CENTRAL DES PONTS ET CHAUSSEES - LCPC

2004-01-01

La connaissance de la masse volumique des particules des eaux résiduaires urbaines est intéressante notamment pour l'étude de leur traitement par décantation ainsi que des relations entre concentrations en matières en suspension et paramètres optiques (turbidimétrie).Une étude des différentes méthodes de mesure de la masse volumique appliquées aux eaux résiduaires a été effectuée par G. Chebbo (1992). Il en a conclu que le pycnomètre à gaz type Beckman est le seul appareil donnant satisfactio...

Problèmes entomologiques en replantation des palmeraies et des cocoteraies

Directory of Open Access Journals (Sweden)

Mariau Dominique

2000-03-01

Full Text Available C’est aux alentours de la vingt-cinquième année que l’on envisage de replanter une palmeraie. C’est en effet vers cet âge que commencent à se poser des problèmes de récolte en raison de la taille des palmiers. En un quart de siècle, l’amélioration génétique aura suffisamment fait de progrès pour escompter un gain de production de l’ordre de 20%. Enfin, dans certaines situations, plusieurs maladies ont pu affecter les vieilles palmeraies. Avec de 15 à 25% d’arbres manquants, principalement lorsque ceux-ci se présentent sous la forme de taches, une diminution de la production se fait nettement sentir. Cela peut, par exemple, être le cas avec les maladies de la fusariose en Afrique de l’Ouest, lorsque la palmeraie n’a pas été plantée avec du matériel végétal tolérant, ou du ganoderma en Malaisie. Le renouvellement des cocoteraies se fait avec un espace de temps beaucoup plus long. En effet, la récolte des noix peut se faire au sol et la hauteur des cocotiers n’est donc pas un facteur limitant. Par ailleurs, la majorité des cocoteraies étant sous la forme de petites plantations villageoises, les agriculteurs rechignent toujours à abattre leurs cocotiers, même si des semences potentiellement plus productives leurs sont proposées. Ce sont les raisons pour lesquelles les cocoteraies de 50 ans et plus représentent la règle. L’abattage d’une plantation de palmiers à huile ou de cocotiers constitue naturellement un changement brutal de l’environnement, ce qui a des conséquences importantes notamment sur l’entomofaune, parmi laquelle des ravageurs majeurs ainsi que leurs ennemis naturels.

Innovation pour la santé des mères et des enfants d'Afrique

International Development Research Centre (IDRC) Digital Library (Canada)

Corey Piccioni

... détermineront les interventions devant absolument faire partie de la formation des travailleurs de santé communautaire. Cela pourrait comprendre des régimes de vitamines prénatals et des billets de transport à des établissements de santé pour le dépistage de troubles d'hypertension ou d'infection au VIH, entre autres.

Isoflurane is a suitable alternative to ether for anesthetizing rats prior to euthanasia for gene expression analysis.

Science.gov (United States)

Nakatsu, Noriyuki; Igarashi, Yoshinobu; Aoshi, Taiki; Hamaguchi, Isao; Saito, Masumichi; Mizukami, Takuo; Momose, Haruka; Ishii, Ken J; Yamada, Hiroshi

2017-01-01

Diethyl ether (ether) had been widely used in Japan for anesthesia, despite its explosive properties and toxicity to both humans and animals. We also had used ether as an anesthetic for euthanizing rats for research in the Toxicogenomics Project (TGP). Because the use of ether for these purposes will likely cease, it is required to select an alternative anesthetic which is validated for consistency with existing TGP data acquired under ether anesthesia. We therefore compared two alternative anesthetic candidates, isoflurane and pentobarbital, with ether in terms of hematological findings, serum biochemical parameters, and gene expressions. As a result, few differences among the three agents were observed. In hematological and serum biochemistry analysis, no significant changes were found. In gene expression analysis, four known genes were extracted as differentially expressed genes in the liver of rats anesthetized with ether, isoflurane, or pentobarbital. However, no significant relationships were detected using gene ontology, pathway, or gene enrichment analyses by DAVID and TargetMine. Surprisingly, although it was expected that the lung would be affected by administration via inhalation, only one differentially expressed gene was extracted in the lung. Taken together, our data indicate that there are no significant differences among ether, isoflurane, and pentobarbital with respect to effects on hematological parameters, serum biochemistry parameters, and gene expression. Based on its smallest affect to existing data and its safety profile for humans and animals, we suggest isoflurane as a suitable alternative anesthetic for use in rat euthanasia in toxicogenomics analysis.

Effect of surface finishing on friction and wear of Poly-Ether-Ether-Ketone (PEEK under oil lubrication

Directory of Open Access Journals (Sweden)

Thiago Fontoura de Andrade

Full Text Available Abstract The tribological properties of poly-ether-ether-ketone (PEEK containing 30% of carbon fiber were studied in an oil-lubricated environment and different surface finishing of the metallic counterbody. Four different finishing processes, commonly used in the automotive industry, were chosen for this study: turning, grinding, honing and polishing. The test system used was tri-pin on disc with pins made of PEEK and counterbody made of steel; they were fully immersed in ATF Dexron VI oil. Some test parameters were held constant, such as the apparent pressure of 2 MPa, linear velocity of 2 m/s, oil temperature at 85 °C, and the time - 120 minutes. The lubrication regime for the apparent pressure of 1 MPa to 7 MPa range was also studied at different sliding speeds. A direct correlation was found between the wear rate, friction coefficient and the lubrication regime, wherein wear under hydrodynamic lubrication was, on average, approximately 5 times lower, and the friction coefficient 3 times lower than under boundary lubrication.

Environment effects on the optical properties of some fluorinated poly(oxadiazole ether)s in binary solvent mixtures

International Nuclear Information System (INIS)

Homocianu, Mihaela; Ipate, Alina Mirela; Hamciuc, Corneliu; Airinei, Anton

2015-01-01

The solvatochromic behavior of some fluorinated poly(oxadiazole ether)s was studied using UV–vis absorption and fluorescence spectroscopy in neat solvents and in their solvent mixtures at several ratios of cosolvents. Quantitative investigations of the spectral changes caused by solvent polarity were discussed using the Lippert‐Mataga, Bakhshiev and Kawski–Chamma–Viallet polarity functions. Repartitioning of cosolvent between local (solvation shell) and bulk phase was investigated by means of a solvatochromic shift method in chloroform–N,N-dimethylformamide (CHCl 3 /DMF) and chloroform–dimethyl sulfoxide (CHCl 3 /DMSO) solvent mixtures. Solvatochromic properties in the binary solvent environments were predominantly influenced by the acidity and basicity of the solvent systems. The fluorescence quenching process by nitrobenzene was characterized by Stern–Volmer plots which display a positive deviation from linearity. This was explained by static and dynamic quenching mechanisms. - Highlights: • Solvatochromic behavior in solvent mixtures was studied. • Stokes shift and local environments in binary mixed solvent were discussed. • Repartitioning of cosolvent between local and bulk phase in solvent mixture has been investigated. • Fluorescence intensity was quenched in presence of nitrobenzene

Optimal conditions in direct dimethyl ether synthesis from syngas utilizing a dual-type fluidized bed reactor

International Nuclear Information System (INIS)

Yousefi, Ahmad; Eslamloueyan, Reza; Kazerooni, Nooshin Moradi

2017-01-01

Concerns over environmental pollution and ever-increasing energy demand have urged the global community to tap clean-burning fuels among which dimethyl ether is a promising candidate for contribution in the transportation sector. Direct dimethyl ether synthesis from syngas, in which methanol production and dehydration take place simultaneously, is arguably the preferred route for large scale production. In this study, direct dimethyl ether synthesis is proposed in an industrial dual-type fluidized bed reactor. This configuration involves two fluidized bed reactors operating in different conditions. In the first catalytic reactor (water-cooled reactor), the synthesis gas is partly converted to methanol after being preheated by the reaction heat in the second reactor (gas-cooled reactor). A two-phase generalized comprehensive reactor model, comprised of the flow in three different regimes is applied and a smooth transition between flow regimes is provided based on the probabilistic averaging approach. The optimal operating conditions are sought by employing differential evolution algorithm as a robust optimization strategy. The dimethyl ether mole fraction is considered as the objective function during the optimization. The results show considerable dimethyl ether enhancement by 16% and 14% compared to the conventional direct dimethyl ether synthesis reactor and dual-type fixed bed dimethyl ether reactor arrangements, respectively. - Highlights: • Dual-type catalytic fluidized bed reactors for dimethyl ether synthesis is studied. • A two-phase comprehensive model comprised of flow in three regimes is used. • Probabilistic averaging approach is applied for smooth transitions between regimes. • Differential evolution method is employed to determine optimal operating conditions. • Production capacity is remarkably enhanced compared to conventional reactor.

Isolement et identification des levures.

Directory of Open Access Journals (Sweden)

S. DOMERCQ

1967-06-01

Full Text Available La fermentation du moût de raisin est assurée par les levures qui se trouvent sur la pellicule du raisin, sur les rafles, et aussi, par celles qui envahissent le matériel de vendange et de vinification dès que la récolte est commencée. L'apparition deLa fermentation du moût de raisin est assurée par les levures qui se trouvent sur la pellicule du raisin, sur les rafles, et aussi, par celles qui envahissent le matériel de vendange et de vinification dès que la récolte est commencée. L'apparition des signes de la fermentation est spontanée. La fermentation est rapide dans la majorité des cas, si elle devient trop violente et que la température s'élève dangeureusement, il faut la « canaliser », la calmer. Des accidents peuvent se produire; des arrêts de fermentation laissant des sucres non fermentés pouvant être attaqués par d'autres microorganismes, des développements de levures formant des substances nuisibles à la qualité; par la suite, il s'agit d'obtenir la stabilité du vin, en particulier, éviter les refermentations des vins doux. L'étude de ces problèmes nécessite une étude préliminaire, celle des levures responsables de la fermentation alcoolique du jus de raisin, qui ne peut être faite que sur des cultures pures, isolées au préalable à l'aide de prélèvements soigneusement réalisés.s signes de la fermentation est spontanée. La fermentation est rapide dans la majorité des cas, si elle devient trop violente et que la température s'élève dangeureusement, il faut la « canaliser », la calmer. Des accidents peuvent se produire; des arrêts de fermentation laissant des sucres non fermentés pouvant être attaqués par d'autres microorganismes, des développements de levures formant des substances nuisibles à la qualité; par la suite, il s'agit d'obtenir la stabilité du vin, en particulier, éviter les refermentations des vins doux. L'étude de ces problèmes nécessite une étude pr

Innovation pour la santé des mères et des enfants d'Afrique | CRDI ...

International Development Research Centre (IDRC) Digital Library (Canada)

L'initiative Innovation pour la santé des mères et des enfants d'Afrique (ISMEA) cherche à améliorer la santé des mères, des nouveau-nés et des enfants en ... Cette initiative de 36 millions de dollars sur sept ans – financée conjointement par les Instituts de recherche en santé du Canada, Affaires mondiales Canada et le ...

Spatial trends of polybrominated diphenyl ether (PBDE) congeners

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Spatial trends of polybrominated diphenyl ether (PBDE) congeners were analyzed in young of the year bluefish collected along the U.S. Atlantic coastline from...

Fuel cell performance of pendent methylphenyl sulfonated poly(ether ether ketone ketone)s

Science.gov (United States)

Zhang, Hanyu; Stanis, Ronald J.; Song, Yang; Hu, Wei; Cornelius, Chris J.; Shi, Qiang; Liu, Baijun; Guiver, Michael D.

2017-11-01

Meta- and para-linked homopolymers bearing 3-methylphenyl (Me) pendent groups were postsulfonated to create sulfonated poly(ether ether ketone ketone) (SPEEKK) backbone isomers, which are referred to as Me-p-SPEEKK and Me-m-SPEEKK. Their thermal and oxidative stability, mechanical properties, dimensional stability, methanol permeability, and proton conductivity are characterized. Me-p-SPEEKK and Me-m-SPEEKK proton conductivities at 100 °C are 116 and 173 mS cm-1, respectively. Their methanol permeabilities are 3.3-3.9 × 10-7 cm2 s-1, and dimensional swelling at 100 °C is 16.4-17.5%. Me-p-SPEEKK and Me-m-SPEEKK were fabricated into membrane electrode assemblies (MEAs), and electrochemical properties were evaluated within a direct methanol fuel cell (DMFC) and proton-exchange membrane fuel cell (PEMFC). When O2 is used as the oxidant at 80 °C and 100% RH, the maximum power density of Me-m-SPEEKK reaches 657 mW cm-2, which is higher than those of Nafion 115 (552 mW cm-2). DMFC performance is 85 mW cm-2 at 80 °C with 2.0 M methanol using Me-p-SPEEKK due to its low MeOH crossover. In general, these electrochemical results are comparable to Nafion. These ionomer properties, combined with a potentially less expensive and scalable polymer manufacturing process, may broaden their potential for many practical applications.

Synthesis of Novel Ether Thionocarbamates and Study on Their Flotation Performance for Chalcopyrite

Directory of Open Access Journals (Sweden)

Gang Zhao

2016-09-01

Full Text Available Novel ether thionocarbamates, O-butoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BIPECTC and O-(2-butoxy-1-methylethoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BMIPECTC, were synthesized in this study. Their collecting efficiencies in the flotation of chalcopyrite were investigated using flotation tests, adsorption measurements, ultraviolet spectra (UV and Fourier transform-infrared spectroscopy (FT-IR and density functional theory (DFT calculations. The synthesized ether thionocarbamates showed better frothing properties than methyl-isobutyl-carbinol (MIBC and stronger affinity to chalcopyrite compared with O-isopropyl-N-ethyl thionocarbamate (IPETC and O-isobutyl-N-ethoxycarbonyl thionocarbamate (IBECTC. UV spectra analysis showed that the ether thionocarbamates react with Cu2+, with the exception of Fe2+, Ni2+, Zn2+ and Pb2+. Additionally, it was further confirmed by FTIR spectra that a chemical reaction occurs between copper ion and BIPECTC and BMIPECTC. The adsorption capacity measurements revealed that chalcopyrite exhibits good adsorption ability for ether thionocarbamates at an approximate pH of 8–10, which agrees with the flotation tests. The quantum chemistry calculation results indicated that the ether thionocarbamates exhibit stronger collecting ability for copper mineral in terms of frontier molecular orbital analysis, binding model simulation with copper ions and the molecular hydrophobicity compared with IPETC and IBECTC. The computational results are in very good agreement with the experimental results.

New aromatic activated dihalides and bisphenol monomers for the preparation of novel poly(arylene ethers)

Science.gov (United States)

Wolfe, James F.

1993-01-01

The goal of this research program was to synthesize a series of unique monomers of type I to be utilized at NASA-Langley in the preparation of new poly(arylene ether ketones), poly(arylene ether ketosulfones), and poly(arylene ether ketophosphine oxides). These A-A and A-B monomer systems, which possess activated aryl halide and/or phenolic end groups, are accessible via condensation reactions of appropriately substituted aryl acetonitrile carbanions with activated aryl dihalides followed by oxidative decyanation.

The action of certain antibiotics and ether on swine enzootic pneumonia.

Science.gov (United States)

Huhn, R G

1971-01-01

The susceptibility of Mycoplasma hyopneumoniae to the action of three antibiotics and diethyl ether was determined. Infected swine were used in an in vivo sensitivity detection system. The parameter of susceptibility was lesion prophylaxis. In vivo, Mycoplasma hyopneumoniae appeared to be resistant to diethyl ether, tylosin tartrate, and erythromycin, but was susceptible to the action of chlortetracycline. Chlortetracycline was effective in preventing the development of lesions when given at levels which would be practical in commercial swine operations.

Triclosan and Hydroxylated Polybrominated Diphenyl Ethers in Lake and Esturaine Sediments

Science.gov (United States)

Arnold, W. A.; Kerrigan, J. F.; McNeill, K.; Erickson, P. R.; Grandbois, M.

2014-12-01

Halogenated diphenyl ethers are a class of emerging contaminants that includes the antibacterial compound triclosan and the flame retardant polybrominated diphenyl ethers (PBDEs). Both triclosan and hydroxylated polybrominated diphenyl ethers (OH-BDEs) are known to form dioxins when exposed to sunlight in aqueous solution. Thus, it is important to understand the sources and presence of these compounds in the environment, especially because OH-BDEs are breakdown products of PBDEs and also naturally produced compounds. In this work, the levels of OH-BDEs were determined in lake sediments from Minnesota and esturaine sediments from San Francisco Bay. Both surface sediments over a broad spatial area and sediment cores were collected and analyzed. Triclosan was used as a marker of wastewater as a source of the targeted emerging contaminants. The relationship between triclosan and OH-BDE levels provides insight into the importance of natural and anthropogenic influences on the levels of OH-BDEs.

Nanocomposite Based on Functionalized Gold Nanoparticles and Sulfonated Poly(ether ether ketone Membranes: Synthesis and Characterization

Directory of Open Access Journals (Sweden)

Iole Venditti

2017-03-01

Full Text Available Gold nanoparticles, capped by 3-mercapto propane sulfonate (Au-3MPS, were synthesized inside a swollen sulfonated poly(ether ether ketone membrane (sPEEK. The formation of the Au-3MPS nanoparticles in the swollen sPEEK membrane was observed by spectroscopic and microscopic techniques. The nanocomposite containing the gold nanoparticles grown in the sPEEK membrane, showed the plasmon resonance λmax at about 520 nm, which remained stable over a testing period of three months. The size distribution of the nanoparticles was assessed, and the sPEEK membrane roughness, both before and after the synthesis of nanoparticles, was studied by AFM. The XPS measurements confirm Au-3MPS formation in the sPEEK membrane. Moreover, AFM experiments recorded in fluid allowed the production of images of the Au-3MPS@sPEEK composite in water at different pH levels, achieving a better understanding of the membrane behavior in a water environment; the dynamic hydration process of the Au-3MPS@sPEEK membrane was investigated. These preliminary results suggest that the newly developed nanocomposite membranes could be promising materials for fuel cell applications.

Analyse des caractéristiques structurelles et des performances ...

African Journals Online (AJOL)

SARAH

28 févr. 2014 ... performances technico-économiques de la riziculture irriguée en Côte d' .... en nous basant sur les prix des intrants et des produits en vigueur au cours ..... la recherche et de la vulgarisation et le transfert de technologies ; (2) ...

Poly-ethers from Winogradskyella poriferorum: Antifouling potential, time-course study of production and natural abundance

KAUST Repository

Dash, Swagatika

2011-08-01

A sponge-associated bacterium, Winogradskyella poriferorum strain UST030701-295T was cultured up to 100l for extraction of antifouling bioactive compounds. Five poly-ethers were isolated and partially characterized based on nuclear magnetic resonance (NMR) spectroscopy and mass spectrometry (MS); two of them showed inhibitory effects on biofilm formation of marine bacteria and larval settlement of macro-foulers but did not produce any adverse effects on the phenotypes of zebra fish embryos at a concentration of 5μgml -1. The effect of culture duration on the production of the poly-ethers and the bioactivity of the relevant extracts was monitored over a period of 12days. The total crude poly-ether production increased from day 2 to day 5 and the highest bioactivity was observed on day 3. The poly-ethers were found to be localized in the cellular fraction of the extracts, implying their natural occurrence. The potent bioactivity of these poly-ethers together with their high natural abundance in bacteria makes them promising candidates as ingredients in antifouling applications. © 2011 Elsevier Ltd.

Enquête de satisfaction des restaurants

CERN Multimedia

Staff Association

2016-01-01

Comité de surveillance des restaurants L’Association du personnel est représentée dans plusieurs comités dont le Comité de surveillance des restaurants (CSR) qui a pour mandat : de donner son avis sur toute question relative à la politique générale de l’Organisation en matière de restauration sur le site, y compris en ce qui concerne les termes et l’attribution des contrats d’exploitation des restaurants ; de définir dans le cadre des contrats d’exploitation des restaurants, les prestations correspondant aux besoins et, dans la mesure du possible, aux désirs du personnel ; de surveiller les prestations des restaurants, y compris en ce qui concerne la qualité et la préparation des produits ; de négocier avec les concessionnaires des restaurants au sujet des tarifs et de surveill...

Contraintes d'adoption des technologies de gestion de la fertilite des ...

African Journals Online (AJOL)

La baisse de fertilité des sols, l'une des principales contraintes du secteur agricole au Togo, sévit encore plus dans la riziculture irriguée où les terres sont exploitées chaque année sans jachère. Face à cette situation, diverses solutions comme les technologies de gestion de la fertilité des sols ont été proposées.

contraintes d'adoption des technologies de gestion de la fertilite des ...

African Journals Online (AJOL)

La baisse de fertilité des sols, l'une des principales contraintes du secteur agricole au Togo, sévit encore plus dans la riziculture irriguée où les terres sont exploitées chaque année sans jachère. Face à cette situation, diverses solutions comme les technologies de gestion de la fertilité des sols ont été proposées.

Droit des organisations internationales

CERN Document Server

Sorel, Jean-Marc; Ndior, Valère

2013-01-01

Cet ouvrage collectif offre aux enseignants et chercheurs en droit international, aux praticiens et aux étudiants, une analyse actualisée du droit des organisations internationales. Il dresse en cinq parties un tableau, illustré par des exemples variés, des problématiques que soulève le phénomène polymorphe d institutionnalisation de la société internationale. La première partie est consacrée au phénomène des « organisations internationales », sous l angle à la fois de l institutionnalisation progressive des relations internationales et de la difficulté à cerner une catégorie unifiée. La deuxième partie rend compte de la création, de la disparition et des mutations des organisations internationales, ici envisagées comme systèmes institutionnels et ordres juridiques dérivés. La troisième partie analyse l autonomie que l acquisition de la personnalité juridique et de privilèges et immunités, un organe administratif intégré, un personnel ou un budget propres confèrent aux organi...

Low-Temperature Oxidation of Dimethyl Ether to Polyoxymethylene Dimethyl Ethers over CNT-Supported Rhenium Catalyst

Directory of Open Access Journals (Sweden)

Qingde Zhang

2016-03-01

Full Text Available Due to its excellent conductivity, good thermal stability and large specific surface area, carbon nano-tubes (CNTs were selected as support to prepare a Re-based catalyst for dimethyl ether (DME direct oxidation to polyoxymethylene dimethyl ethers (DMMx. The catalyst performance was tested in a continuous flow type fixed-bed reactor. H3PW12O40 (PW12 was used to modify Re/CNTs to improve its activity and selectivity. The effects of PW12 content, reaction temperature, gas hourly space velocity (GHSV and reaction time on DME oxidation to DMMx were investigated. The results showed that modification of CNT-supported Re with 30% PW12 significantly increased the selectivity of DMM and DMM2 up to 59.0% from 6.6% with a DME conversion of 8.9%; besides that, there was no COx production observed in the reaction under the optimum conditions of 513 K and 1800 h−1. The techniques of XRD, BET, NH3-TPD, H2-TPR, XPS, TEM and SEM were used to characterize the structure, surface properties and morphology of the catalysts. The optimum amount of weak acid sites and redox sites promotes the synthesis of DMM and DMM2 from DME direct oxidation.

Atténuation des risques pour la santé dans le secteur de la poterie ...

International Development Research Centre (IDRC) Digital Library (Canada)

En effet, les potiers utilisent un carburant de piètre qualité (de la poussière de coton et du coton mazouté) pour faire fonctionner leurs fours en briques, ce qui engendre une importante pollution atmosphérique, contribuant ainsi aux problèmes de santé majeurs dans les secteurs environnants. Le présent projet vise à ...

Synthesis of hydroxylated and methoxylated polybrominated diphenyl ethers

Institute of Scientific and Technical Information of China (English)

ZHENG Ke-wen; GAO Li-ping; CAO Jie; YU Hai-wen; ZHANG Zhang

2009-01-01

Hydroxylated/methoxylated polybrominated diphenyl ethers (OH/MeO-PBDEs) are not only detected as natural products, but also regarded as metabolites formed from polybrominated diphenyl ethers (PBDEs), which are widely used as flame-retardants in various materials. The aim of the present study was to synthesize authentic OH-PBDEs and MeO-PBDEs, as reference standards for environmental exploration. Twenty OH-PBDEs and their corresponding MeO-PBDEs containing three to six bromine atoms were synthesized via a trial of reactions including coupling, oxidation, bromination, methylation, etc. The products were characterized by GC-MS and 1H-NMR spectroscopy in the work. As results show, all compounds synthesized were up to 99% on purity and be reqarded as authentic standards for detecting the chemical pollutants in the emvironment.

Degradation of the Alternaria mycotoxins alternariol, alternariol monomethyl ether, and altenuene upon bread baking.

Science.gov (United States)

Siegel, David; Feist, Michael; Proske, Matthias; Koch, Matthias; Nehls, Irene

2010-09-08

The stability of the Alternaria mycotoxins alternariol, alternariol monomethyl ether, and altenuene upon bread baking was investigated by model experiments using a spiked wholemeal wheat flour matrix. For alternariol and alternariol monomethyl ether, but not for altenuene, degradation products, formed through a sequence of hydrolysis and decarboxylation, could be identified in pilot studies. The simultaneous quantification of alternariol, alternariol monomethyl ether, altenuene, and the degradation products was achieved by a newly developed high performance liquid chromatography tandem mass spectrometry (HPLC-MS/MS) multimethod. The obtained quantitative data indicate that the Alternaria mycotoxins are barely degraded during wet baking, while significant degradation occurs upon dry baking, with the stability decreasing in the order alternariol monomethyl ether>alternariol>altenuene. The novel degradation products could be detected after the wet baking of flour spiked with alternariol and in a sample survey of 24 commercial cereal based baking products.

Synthesis and biological evaluation of arctigenin ester and ether derivatives as activators of AMPK.

Science.gov (United States)

Shen, Sida; Zhuang, Jingjing; Chen, Yijia; Lei, Min; Chen, Jing; Shen, Xu; Hu, Lihong

2013-07-01

A series of new arctigenin and 9-deoxy-arctigenin derivatives bearing different ester and ether side chains at the phenolic hydroxyl positions are designed, synthesized, and evaluated for activating AMPK potency in L6 myoblasts. Initial biological evaluation indicates that some alkyl ester and phenethyl ether arctigenin derivatives display potential activities in AMPK phosphorylation improvement. Further structure-activity relationship analysis shows that arctigenin ester derivatives 3a, 3h and 9-deoxy-arctigenin phenethyl ether derivatives 6a, 6c, 6d activate AMPK more potently than arctigenin. Moreover, the 2-(3,4-dimethoxyphenyl)ethyl ether moiety of 6c has been demonstrated as a potential functional group to improve the effect of AMPK phosphorylation. The structural optimization of arctigenin leads to the identification of 6c as a promising lead compound that exhibits excellent activity in AMPK activation. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

De la problématique des articles synopsis dans la compilation des ...

African Journals Online (AJOL)

Autrement dit, au Gabon l'attention doit porter sur l'utilisation des articles synopsis dans la compilation des dictionnaires, en vue de refléter dans ses ouvrages la diversité linguistique et culturelle de ce pays. Ceci est d'autant plus vrai que l'utilisation des articles synopsis ne dépend aucunement de la typologie du ...

Improved microstructure and properties of 12Cr2Ni4A alloy steel by vacuum carburization and Ti + N co-implantation

Science.gov (United States)

Dong, Meiling; Cui, Xiufang; Jin, Guo; Wang, Haidou; Cai, Zhaobing; Song, Shengqiang

2018-05-01

The carburized 12Cr2Ni4A alloy steel was implanted by Ti + N double elements implantation. The microstructure, nano-hardness and corrosion properties were investigated by EPMA, TEM, XPS, nano-hardness and electrochemistry tests in detail. The results showed that the Ti + N co-implanted layer is composed of FCC TiN and TiC phases with BCC martensite. Compared with the un-implanted layer, the Ti + N implanted layer has higher nano-hardness and better corrosion resistance. In addition, the higher nano-hardness was presented below the surface of 1800 nm compared with un-implanted layer, which is far beyond the thickness of the implanted layer. The results also indicated that the generation of nanoscale ceramic phase and structures are not the only factor to impose the influence on the nano-hardness and corrosion resistance, but the radiation damage and lattice distortion will play an important role.

Polyether ether ketone film. Polyether ether ketone film

Energy Technology Data Exchange (ETDEWEB)

Suzuki, S. (Sumitomo Chemical Co. Ltd., Tokyo (Japan))

1990-07-05

The characteristics and the film making process of polyether ether ketone (PEEK) resin, and the characteristics and the applications of PEEK film, are described. PEEK is aromatic polyketone with super thermal resistance. Though it is a crystalline polymer of which the crystallinity is controlled to 48% in a highest degree, it has also amorphous property, thus it shows unique property. The characteristics of PEEK resin are found in thermal resistance, incombusti-bility, transparency, chemical resistance, light resistance and radiation resistance. As for the film making process, casting method by T-die is generally adopted. The general properties of PEEK film are excellent in high thermal resistance, good electrical properties, chemical resistance, hydrolysis resistance, radiation resistance and imcombusti-bility. In the application of PEEK film, new development is expected in following fields; a high performance composite, flexible print substrate with high thermal resistance, insulating tape with thermal resistance, and a general film in the nuclear energy industry. 5 figs., 5 tabs.

Leaching characteristics of polybrominated diphenyl ethers (PBDEs) from flame-retardant plastics.

Science.gov (United States)

Kim, Yong-Jin; Osako, Masahiro; Sakai, Shin-ichi

2006-10-01

To investigate the effect of leachant on the leachability of polybrominated diphenyl ethers (PBDEs), we determined the leaching concentrations of PBDEs from flame-retardant plastic samples (TV housings and raw materials before molding processing) that are regarded as a source of PBDEs in landfill sites. The leachants used were distilled water, 20% methanol solution, and dissolved humic solution (DHS) of 1000 mg/l based on organic carbon. The leaching test conditions were a liquid-to-solid ratio of 100:1, and a contact period of five days, with twice-daily agitation in a temperature-controlled room of 30 degrees C without pH or ionic strength control. The leaching concentrations of PBDEs increased with increased content, and were found to be remarkably enhanced when methanol and DHS were used instead of distilled water. The enhancement of leachability in the presence of the latter was attributed to the cosolvency effect, and complex formations between the PBDEs and dissolved humic matter (DHM). PBDE concentrations in the leachate obtained from the leaching test and an actual landfill site revealed a significant presence of congeners below heptabromodiphenyl ethers (H7BDEs), detected in the leachate of the actual landfill, while significant amounts of nonabromodiphenyl ethers (N9BDEs) and decabromodiphenyl ether (D10BDE) were detected in the leachate of the leaching test.

Photosynthesis involvement in the mechanism of action of diphenyl ether herbicides.

Science.gov (United States)

Ensminger, M P; Hess, F D

1985-05-01

Photosynthesis is not required for the toxicity of diphenyl ether herbicides, nor are chloroplast thylakoids the primary site of diphenyl ether herbicide activity. Isolated spinach (Spinacia oleracea L.) chloroplast fragments produced malonyl dialdehyde, indicating lipid peroxidation, when paraquat (1,1'-dimethyl-4,4'-bipyridinium ion) or diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] were added to the medium, but no malonyl dialdehyde was produced when chloroplast fragments were treated with the methyl ester of acifluorfen (methyl 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-nitrobenzoic acid), oxyfluorfen [2-chloro-1-(3-ethoxy-4-nitrophenoxy)-4-(trifluoromethyl)benzene], or MC15608 (methyl 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-chlorobenzoate). In most cases the toxicity of acifluorfen-methyl, oxyfluorfen, or MC15608 to the unicellular green alga Chlamydomonas eugametos (Moewus) did not decrease after simultaneous treatment with diuron. However, diuron significantly reduced cell death after paraquat treatment at all but the highest paraquat concentration tested (0.1 millimolar). These data indicate electron transport of photosynthesis is not serving the same function for diphenyl ether herbicides as for paraquat. Additional evidence for differential action of paraquat was obtained from the superoxide scavenger copper penicillamine (copper complex of 2-amino-3-mercapto-3-methylbutanoic acid). Copper penicillamine eliminated paraquat toxicity in cucumber (Cucumis sativus L.) cotyledons but did not reduce diphenyl ether herbicide toxicity.

Evaluation des pratiques de gestion des adventices en riziculture

African Journals Online (AJOL)

Les résultats ont montré que les méthodes de gestion de l'enherbement ont .... Le contrôle des adventices en riziculture irriguée a principalement .... mesurer la hauteur des plantes et la longueur ..... Performance agronomique du Sys- tème de ...

Selectivity in stripping of alkali-metal cations from crown ether carboxylate complexes

International Nuclear Information System (INIS)

Bartsch, R.A.; Walkowiak, W.; Robison, T.W.

1992-01-01

To probe the effect of structural variations within the ionophore upon the efficiency and selectivity of solvent extraction, a variety of crown ether carboxylic acids and phosphonic acid monoesters have been synthesized. In other studies the influence of the organic diluent upon extraction efficiency and selectivity has been probed for such proton-ionizable crown ethers. In the present investigation, attention is focused upon selectivity in the stripping step. Although the efficiency of metal ion stripping is often examined in solvent extraction studies, the selectivity of competitive metal ion release under different conditions is much less frequently considered. In this study, competitive stripping of metal ions from chloroform solutions of five-alkali-metal crown ether carboxylates by varying concentrations of aqueous hydrochloric acid is examined. Alkali metals used were Li, Na, K, Rb, and Cs

APPLICATION OF PHOTOCATALYTIC PROCESS FOR REMOVAL OF METHYL TERT-BUTYL ETHER FROM HIGHLYCONTAMINATED WATER

Directory of Open Access Journals (Sweden)

A. Mesdaghinia

2007-09-01

Full Text Available The oxygenate methyl tert-butyl ether is added to gasoline to increase the octane level and to reduce carbon monoxide and hydrocarbon emissions by vehicles. The high mobility, water solubility, and resistance to natural attenuation associated with methyl tert-butyl ether may result in contamination of ground and surface waters. In this research the degradation of aqueous methyl tert-butyl ether at relatively high concentrations was investigated by UV-vis/TiO2/H2O2 photocatalytic process. The effect of important operational parameters such as pH, amount of H2O2, catalyst loading, and irradiation time were also studied. Concentrations of methyl tert-butyl ether and intermediates such as tert-butyl formate and tert-butyl alcohol were measured over a 180 min period using a gas chromatograph equipped with flame ionization detector and combined with headspace sampler. Results showed that the time required for complete degradation increased from 30 to 180min, when the initial concentration was increased from 10 to 500mg/L. The first order rate constant for degradation of methyl tert-butyl ether from the hydroxyl radical was estimated to be 0.177 to 0.022 1/min as the concentration increased from 10 to 500mg/L. Study on the overall mineralization monitored by total organic carbon (TOC analysis showed that in the initial concentration of 100mg/L methyl tert-butyl ether, complete mineralization was obtained after 110min under UV-vis/TiO2/H2O2 photocatalytic process.

Contrôle des Circuits Auxiliaires des P.F.W. (arrêt machine 2003/2004)

CERN Document Server

Ottaviani, J

2004-01-01

Les PFW sont des nappes polaires installées sur les pôles des aimants du PS. Elles sont au nombre de 4 par unité d'aimant et constituées d'un circuit principal (dans lequel circule le courant désiré selon le cycle magnétique utilisé) et des circuits auxiliaires. Les circuits auxiliaires sont des enroulements de correction (boucles de tour et "pick-up" brasés sur les enroulements principaux). Pendant la variation du champ magnétique del'aimant PS, on utilise des tensions induites dans ces circuits auxiliaires pour corriger les erreurs de champ dues aux pertes par courants de Foucault dans la chambre à vide. Chaque année, pendant l'arrêt machine, on vérifie si les caractéristiques des circuits auxiliaires correspondent aux normes (mesures de résistances des boucles de tours, résistances entre "pick-up" et isolation des circuits) afin de faire un suivi. Les 404 PFW sont ainsi vérifiées. Dans cette note, on ne relèvera que les PFW ayant des défauts (valeurs hors tolérances, boucles ouvertes ...

Performances des équipements utilisés en liaison froide en liaison froide en restauration hospitalière - Suivi des températures des entrées froides

OpenAIRE

Rosset , Philippe; Morelli , Elisabeth; Noël , Véronique; Poumeyrol , Gérard

2007-01-01

La restauration hospitalière présente un système de distribution des repas qui lui est spécifique : assemblage des denrées préparées et constitution des plateaux-repas dans un local dédié (dit d'allotissement) ; transport des plateaux-repas vers les unités de soins dans des enceintes mobiles permettant le maintien au froid des denrées consommées froides et la remise en température des aliments à consommer chauds. La présente étude concerne le suivi des températures de hors-d'œuvre dans trois ...

Phenyl ethers from cultured lichen mycobionts of Graphis scripta var. serpentina and G. rikuzensis.

Science.gov (United States)

Takenaka, Yukiko; Tanahashi, Takao; Nagakura, Naotaka; Hamada, Nobuo

2003-07-01

Spore-derived mycobionts of the lichen Graphis scripta var. serpentina and G. rikuzensis were cultivated on a malt-yeast extract medium supplemented with 10% sucrose and their metabolites were investigated. 3,3'-Dihydroxy-5,5'-dimethyldiphenyl ether was isolated from the cultures of the mycobionts of G. scripta var. serpentina, while a new phenyl ether, rikuzenol, along with two known diphenyl ethers, violaceol-I and violaceol-II, were isolated from those of G. rikuzensis. The structure of the new compound was determined by spectroscopic methods. Violaceol-I was chemically synthesized and interconversion between violaceol-I and violaceol-II was proven.

Effect of cryogenic treatment on tensile behavior of case carburized steel-815M17

International Nuclear Information System (INIS)

Bensely, A.; Senthilkumar, D.; Mohan Lal, D.; Nagarajan, G.; Rajadurai, A.

2007-01-01

The crown wheel and pinion represent the most highly stressed parts of a heavy vehicle; these are typically made of 815M17 steel. The reasons for the frequent failure of these components are due to tooth bending impact, wear and fatigue. The modern processes employed to produce these as high, durable components include cryogenic treatment as well as conventional heat treatment. It helps to convert retained austenite into martensite as well as promote carbide precipitation. This paper deals with the influence of cryogenic treatment on the tensile behavior of case carburized steel 815M17. The impetus for studying the tensile properties of gear steels is to ensure that steels used in gears have sufficient tensile strength to prevent failure when gears are subjected to tensile or fatigue loads, and to provide basic design information on the strength of 815M17 steel. A comparative study on the effects of deep cryogenic treatment (DCT), shallow cryogenic treatment (SCT) and conventional heat treatment (CHT) was made by means of tension testing. This test was conducted as per ASTM standard designation E 8M. The present results confirm that the tensile behavior is marginally reduced after cryogenic treatment (i.e. both shallow and deep cryogenic treatment) for 815M17 when compared with conventional heat treatment. Scanning electron microscopic (SEM) analysis of the fracture surface indicates the presence of dimples and flat fracture regions are more common in SCT specimens than for CHT and DCT-processed material

Vers une meilleure comprehension des savoirs disciplinaires et curriculaires des enseignants ou Ie paradigme retrouve

Directory of Open Access Journals (Sweden)

Stephane Martineau

1999-01-01

Full Text Available eet article se veut essentieUement un travail de synthese sous la forme d 'une breve revue de litterature au sujet des savoirs disciplinaires et curriculaires en enseignement. Plus specifiquement, il vise a determiner queUes sont les principales conclusions qui se degagent de la lecture des recherches empiriques sur les savoirs disciplinaires et curriculaires des enseignants des ordres d'enseignement primaire et secondaire. Il propose donc une classification des differentes dimensions constitutives du rapport entre les savoirs disciplinaires et curriculaires et la pratique enseignante. Les resultats mis au jour permettent d 'une part, d'identifier les facteurs qui entrainent des differences dans les connaissances disciplinaires et curriculaires des enseignants et d'autre part, de mieux saisir comment ces connaissances de l'enseignant peuvent influencer en retour sa pratique.

Contrôle hormonal des caractéristiques des fibres musculaires après la naissance

OpenAIRE

Cassar-Malek, Isabelle; Listrat, Anne; Picard, Brigitte

1998-01-01

Après la naissance, la croissance et les propriétés contractiles et métaboliques des fibres musculaires sont soumises à une régulation endocrinienne complexe. A l’exception des glucocorticoïdes, la plupart des hormones présente une action anabolique sur le tissu musculaire. Leur influence sur les caractéristiques des fibres est cependant très différente. Ainsi, les hormones somatotropes affectent peu la composition en fibres des muscles. La GH, comme l’IGF-1, régulerait cependant l’expression...

Modélisation des propriétés diélectriques des nanocomposites ...

African Journals Online (AJOL)

Dans ce travail, nous nous intéressons aux propriétés diélectriques dans le domaine des micro-ondes (2.45, 9.50 et 35 GHz) des composites constitués des inclusions de noir de carbone dans une matrice résine époxyde. Nous avons utilisé deux types de carbone : le monarch 700 et le sterling, dont les diamètres des ...

Calcium carbonate growth in the presence of water soluble cellulose ethers

International Nuclear Information System (INIS)

Zhang Fengju; Yang Xinguo; Tian Fei

2009-01-01

Calcium carbonate precipitation was performed in the presence of methyl cellulose (MC) and two kinds of hydroxyethyl cellulose (HEC FD-10000, HEC FD-30000). The results demonstrated that the final product morphology and structure of CaCO 3 crystals are highly sensitive to the concentration of the cellulose ethers aqueous solution. By precisely controlling their concentrations, all these three cellulose ethers solutions have the ability of protecting metastable vaterite from thermodynamically transforming into stable calcite. The intermediate products investigation showed to some extent the phase transformation of calcium carbonate in its growing process from metastable vaterite to calcite and indicated that the calcium carbonate crystal growth in HEC solutions occurs through dissolution and reprecipitation process. Calcium carbonate growth in both presence of HEC and ethanol or Mg 2+ was also examined. This work demonstrates the potential of water soluble cellulose ethers in controlling biominerals crystallization and growth. The results are revelatory for biomineralization and fabricating new organic-inorganic hybrids based on cellulose derivatives.

Civili, langue des Baloango

DEFF Research Database (Denmark)

Mavoungou, Paul Achille; Ndinga-Koumba-Binza, Hugues Steve

, Congo, Angola, etc.) issus de la décolonisation. Il présente de façon succincte quelques phénomènes historiques, phonologiques, morphosyntaxiques, homonymiques et analogiques de la langue. Des faits sémantiques des emprunts linguistiques y sont également décrits dans le cadre des changements...

Comment constituer et traiter des corpus issus des médias sociaux à l’aide des CAQDAS? NVivo : un instrument pour l’analyse des discours numériques

Directory of Open Access Journals (Sweden)

Ferrari Giovannipaolo

2015-01-01

Full Text Available Avec l’apparition des médias sociaux, le chercheur en Sciences Humaines et Sociales a vu s’ouvrir des possibilités de création de corpus à partir des données disponibles en ligne. Le risque dans ces modalités de création de corpus est de créer de grandes bases de données difficilement gérables avec les outils traditionnels et surtout dans le cadre d’une recherche qualitative. Pour cette raison, il semble important de mobiliser des outils numériques pour l’aide à la recherche. Ces logiciels sont appelés CAQDAS. Cette contribution montre comment les utiliser pour une enquête de terrain en ligne ou numérique afin d’organiser et d’analyser un corpus. Ce corpus est constitué en vue d’une analyse des discours produits dans le contexte professionnel de la radio utilisant les nouveaux médias.

Volumetric and viscometric study of aqueous binary mixtures of some glycol ethers at T = (275.15 and 283.15) K

International Nuclear Information System (INIS)

Dhondge, Sudhakar S.; Pandhurnekar, Chandrashekhar P.; Sheikh, Shaziya; Deshmukh, Dinesh W.

2011-01-01

Graphical abstract: Highlights: → Study of aqueous solutions of glycol ethers at low temperatures is presented. → Glycol ethers are industrially important liquids. → Reduction in the volume was observed upon addition of all glycol ethers to water. → Glycol ethers act as structure makers in aqueous medium. - Abstract: The experimental data for the density (ρ) and viscosity (η) are reported for aqueous binary mixtures of different glycol ethers, namely ethylene glycol monomethyl ether (EGMME), ethylene glycol monoethyl ether (EGMEE), diethylene glycol monomethyl ether (DEGMME), and diethylene glycol monoethyl ether (DEGMEE), at different temperatures (T = 275.15 K and 283.15 K) within the concentration range 0 mol . kg -1 to 0.1 mol . kg -1 . The values of density (ρ) and viscosity (η) of the solutions were used to compute different derived parameters, such as apparent molar volume (φ V ) of the solute, excess molar volume (V E ) of the solution, viscosity B and D coefficients of solution and temperature coefficient of viscosity B-coefficient (dB/dT) of solution. The limiting apparent molar volume of the solutes (φ V 0 ) have been obtained for aqueous binary mixtures of these glycol ethers by smooth extrapolation of φ V -m curves to zero concentration. By using the values of φ V 0 , the limiting excess partial molar volumes (V-bar 2 0E ) have also been calculated. The results are interpreted in term of various interactions such as solute-solvent interactions and hydrogen bonding.

Planar Edge Terminations and Related Manufacturing Process Technology for High Power 4H-SiC Diodes

OpenAIRE

Pérez Rodríguez, Raúl

2005-01-01