Portable digital reactivity meter for power reactors

Energy Technology Data Exchange (ETDEWEB)

Steffen, G [Nuklear-Ingenieur Service G.m.b.H., Hanau (Germany, F.R.)

1977-07-01

A digital reactivity meter has been developed, which can be used for all kinds of kinetic reactivity measurements in PWR's and BWR's. The input signals may be supplied by standard neutron detectors of the reactor. The hardware configuration consists of a minicomputer with ADC and DAC, a 'Silent' terminal and a high speed paper tape reader/punch. It is easily transportable. The reactivity meter solves the inverse kinetics equations for 6 delayed neutron groups, simultaneously for up to 8 logarithmic or linear neutron flux signals. It has been successfully tested at Biblis A PWR and the KRB BWR.

Rupture tests with reactor pressure vessel head models

International Nuclear Information System (INIS)

Talja, H.; Keinaenen, H.; Hosio, E.; Pankakoski, P.H.; Rahka, K.

2003-01-01

In the LISSAC project (LImit Strains in Severe ACcidents), partly funded by the EC Nuclear Fission and Safety Programme within the 5th Framework programme, an extensive experimental and computational research programme is conducted to study the stress state and size dependence of ultimate failure strains. The results are aimed especially to make the assessment of severe accident cases more realistic. For the experiments in the LISSAC project a block of material of the German Biblis C reactor pressure vessel was available. As part of the project, eight reactor pressure vessel head models from this material (22 NiMoCr 3 7) were tested up to rupture at VTT. The specimens were provided by Forschungszentrum Karlsruhe (FzK). These tests were performed under quasistatic pressure load at room temperature. Two specimens sizes were tested and in half of the tests the specimens contain holes describing the control rod penetrations of an actual reactor pressure vessel head. These specimens were equipped with an aluminium liner. All six tests with the smaller specimen size were conducted successfully. In the test with the large specimen with holes, the behaviour of the aluminium liner material proved to differ from those of the smaller ones. As a consequence the experiment ended at the failure of the liner. The specimen without holes yielded results that were in very good agreement with those from the small specimens. (author)

Establishing a PWR burn-up library

International Nuclear Information System (INIS)

Lutz, D.C.

1981-01-01

Starting out from data file ENDF/B IV /1/, a cross-section library has been established for the calculation of operating conditions in pressurized water reactors of the type used in BIBLIS B. The library includes macroscopic, homogenized 2-group cross-sections for all types of fuel elements used in this reactor, including those equipped with boron glass rods. For their calculation the previous irradiation of the fuel has been taken into consideration by approximation. Information on fuel consumption from cell burn-up calculations has been stored in a separate data file. It was designed as a base for the determination of cross sections to be used in the calculation of the incident ''main-steam pipe fracture''. For this library the description of cross sections as a function of the moderator status chose the water densities at 300 0 C/155 bar, 190 0 C/140 bar and 100 0 C/100 bar as fixed values. The burn-up library has been tested by a three-dimensional calculation for the 1sup(st) cycle of the BIBLIS B-reactor using program QUABOX /2/. This showed variances with the anticipated course concerning critically, which can be explained almost quantitatively by known deficiencies of the ENDF/b-IV library. (orig.) [de

Releases of ¹⁴CO₂ from nuclear facilities with gaseous effluents; Die Emission von 14C02 mit der Abluft kerntechnischer Anlagen

Energy Technology Data Exchange (ETDEWEB)

Schuettelkopf, H.

1977-06-01

Since only little information is available about the extent and type of the ¹⁴C emission from nuclear facilities, the Radiation Protection and Safety Department of the Karlsruhe Nuclear Research Center has measured the ¹⁴C stack vent emission from various facilities. The measurement was restricted to ¹⁴CO₂ because it is only this coumpound which can lead to exposure doses as a result of ingestion and inhalation. Sampling was carried out with 200 ml of 5 M NaOH in a scrubber. The sample flow was 1 l/min. The sampling period was one week. The ¹⁴CO₂ emission was measured in the stack vent air of the FR-2 research reactor, the Multi-purpose Research Reactor (MZFR), the combustion facility for burnable radioactive waste (FERAB), the Karlsruhe Reprocessing Plant (WAK), all of which are located on the premises of the Karlsruhe Nuclear Research Center, and in the exhaust air of the Obrigheim (KWO) and Biblis A Nuclear Power Stations.

Chemical compatibility issues associated with use of SiC/SiC in advanced reactor concepts

Energy Technology Data Exchange (ETDEWEB)

Wilson, Dane F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

Silicon carbide/silicon carbide (SiC/SiC) composites are of interest for components that will experience high radiation fields in the High Temperature Gas Cooled Reactor (HTGR), the Very High Temperature Reactor (VHTR), the Sodium Fast Reactor (SFR), or the Fluoride-cooled High-temperature Reactor (FHR). In all of the reactor systems considered, reactions of SiC/SiC composites with the constituents of the coolant determine suitability of materials of construction. The material of interest is nuclear grade SiC/SiC composites, which consist of a SiC matrix [high-purity, chemical vapor deposition (CVD) SiC or liquid phase-sintered SiC that is crystalline beta-phase SiC containing small amounts of alumina-yttria impurity], a pyrolytic carbon interphase, and somewhat impure yet crystalline beta-phase SiC fibers. The interphase and fiber components may or may not be exposed, at least initially, to the reactor coolant. The chemical compatibility of SiC/SiC composites in the three reactor environments is highly dependent on thermodynamic stability with the pure coolant, and on reactions with impurities present in the environment including any ingress of oxygen and moisture. In general, there is a dearth of information on the performance of SiC in these environments. While there is little to no excess Si present in the new SiC/SiC composites, the reaction of Si with O₂ cannot be ignored, especially for the FHR, in which environment the product, SiO₂, can be readily removed by the fluoride salt. In all systems, reaction of the carbon interphase layer with oxygen is possible especially under abnormal conditions such as loss of coolant (resulting in increased temperature), and air and/ or steam ingress. A global outline of an approach to resolving SiC/SiC chemical compatibility concerns with the environments of the three reactors is presented along with ideas to quickly determine the baseline compatibility performance of SiC/SiC.

Leituras e ações na Encontros Bibli

Directory of Open Access Journals (Sweden)

Ursula Blattmann

2010-05-01

Full Text Available Em cada edição publicada merece o destaque a participação de autores, avaliadores e demais colegas. É um momento que deve ser festejado, pois são etapas nas quais a perseverança, a vontade de fazer e a pontualidade estão presentes.Das leituras dos originais à tomada de decisão pelo aceite ou não, se efetua por tantas mãos e se torna uma rotina, por vezes grata, outras, ingrata. Os afazeres e ações na nossa rotina interna da Encontros Bibli provém desta força maior que nos anima a cada edição publicada. E compartilhamos a todos os leitores a satisfação de apresentar a edição do volume 15, número 29 com 10 (dez artigos e um dossiê referente ao Encontro sobre Repositórios de Objetos Virtuais, realizado em novembro de 2009 em Florianópolis.Os artigos são de 17 colegas que atuam em sete universidades, sendo cinco brasileiras; uma argentina; uma espanhola; do Instituto Federal de Educação, Ciência e Tecnologia de Paraíba e do Instituto Brasileiro de Informação, Ciência e Tecnologia. Expressamos nossa admiração aos pesquisadores que se dedicam ao ensino e a pesquisa de nossa área do conhecimento e conseguem criar espaços para escrever e publicar, contribuindo com suas reflexões e análises para o crescimento da Ciência da Informação.Os textos tramitaram nos fluxos do processo editorial desde o início de 2009 e agora tornam-se disponíveis aos leitores: O campo da ciência da informação e o patrimônio cultural: reflexões iniciais para novas discussões sobre os limites da área, de Willian Eduardo Righini de Souza e Giulia Crippa.A infra-estrutura em informação científica e em Ciência da Informação na antiga União Soviética (1917-1991, escrita por Roberto Lopes dos Santos Júnior e Lena Vânia Ribeiro Pinheiro.O profissional bibliotecário como gestor de pessoas, na visão de Adilson Luiz Pinto e de José Antonio Moreiro González.Fluxos informacionais para o monitoramento da Convenção dos

The German reactor safety study

International Nuclear Information System (INIS)

Birkhofer, A.

1980-01-01

The most important results of the German risk study of a nuclear power plant equipped with a pressurized water reactor were published in August 1979. The main volume of the study with the approach used and the results elaborated has been available for reference since late 1979. Eight technical volumes contain detailed descriptions and documentations of the investigations carried out. The reference facility used as a basis for the technical plant studies was unit B of the Biblis Nuclear Power Station, a KWU PWR of 3750 MW thermal power. This contribution provides more detailed explanations of the methods and the results of the risk study illustrated by examples. The description refers to accident categories and categories of radioactivity releases, probabilities of specific sequences of accident events, and the damage associated with core meltdown accidents as a function of various types of failure. For purposes of evaluation and application of the results the limits in the basic assumptions of the study are referred to. (orig./HP) [de

Prometheus Reactor I&C Software Development Methodology, for Action

Energy Technology Data Exchange (ETDEWEB)

T. Hamilton

2005-07-30

The purpose of this letter is to submit the Reactor Instrumentation and Control (I&C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I&C Software Development Process Manual and Reactor Module Software Development Plan to NR for information.

Determination of sodium and organic substances for quality control in the full-desalination plant of the Biblis nuclear power plant

International Nuclear Information System (INIS)

Brunner, R.E.; Doerr, A.

1977-01-01

After four years of operation of the make up water treatment plant of nuclear POWER STATION BIBLIS an examination was made concerning the total through put, the eluation of ions and organic matters, and further concerning the efficiency of a special regeneration technique for the counter current regenerated ion exchange beds. In order to determine the efficiency of the applied regeneration methods analisis were carried out on a great number of water samples for sodium, chloride, COD and humic acids as well. A comparison was made between the anialytical determination of Sodium with an automatic analyser and the method used in the laboratory by means of flame photometry respectively ion potential measurement. (orig.) [de

STRATEG - an incident training system for thermohydraulic effects and principles

International Nuclear Information System (INIS)

Rehn, H.; Majohr, N.

1993-01-01

STRATEG is a 1:10 scale glass model of a PWR (Biblis B reactor coolant circuit) built by RWE in 1986 on the site of the Biblis plant as a training model. The model can be used for training of normal operation and incident situations since all important operating and incident sequences of a PWR can be simulated. Thermodynamic phenomena can also be demonstrated occurring under various operating situations and in particular associated with malfunctions. (Z.S.) 1 tab., 3 figs., 1 ref

Recursos tecnológicos e informacionais ativos na Encontros Bibli

Directory of Open Access Journals (Sweden)

Araci Isaltina de Andrade Hillesheim

2010-10-01

Full Text Available As tecnologias da informação e comunicação permeiam o nosso processo de editoração científica. Entre os dias 14 e 16 de julho de 2010, realizou-se, em Florianópolis, no Auditório da Reitoria da Universidade Federal de Santa Catarina, o I Encontro Nacional de Usuários do SEER (a programação, vídeos e relatos estão disponíveis no site http://euseer.ibict.br/index.php/euseer1/euseer1. Foi uma satisfação receber e encontrar colegas editores, avaliadores, autores, bolsistas, leitores e principalmente nossos mestres no uso da Plataforma Open Journal Systems (http://pkp.sfu.ca/?q=ojs – ou melhor, toda a equipe do IBICT responsável pelos estudos, customização, desenvolvimento e disseminação da edição em português, resultando na adoção desse Sistema Eletrônico de Editoração de Revistas – SEER, utilizado por mais de 800 revistas científicas somente no Brasil (conforme registrado no Portal SEER - http://seer.ibict.br/.Acompanhar a evolução das ferramentas tecnológicas, aplicar os recursos de novas versões e a troca de conhecimentos tornam-se uma experiência enriquecedora nos processos de aprender-saber-fazer. Em julho desse ano, a administração do Portal Periódicos UFSC (http://www.periodicos.ufsc.br/ migrou a plataforma para a nova versão e novas funcionalidades foram ativadas pelos editores gerentes das revistas.A Encontros Bibli ativou algumas ferramentas, entre as quais, disponibilizar os acessos estatísticos dos arquivos publicados dos autores. Isto é, o autor que tem um artigo publicado em nossa revista poderá consultar, no seu perfil, os dados referentes aos respectivos acessos de cada artigo. Paralelamente, com a nova versão, houve mudanças no autoarquivamento, isto é, quando o autor submete um arquivo na plataforma, pode preencher os metadados com maior facilidade, pois estão disponibilizadas as abas nos idiomas português e inglês. Gradativamente, os metadados ganham maior destaque no tratamento

Prometheus Reactor I and C Software Development Methodology, for Action

International Nuclear Information System (INIS)

T. Hamilton

2005-01-01

The purpose of this letter is to submit the Reactor Instrumentation and Control (I and C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I and C Software Development Process Manual and Reactor Module Software Development Plan to NR for information

Conclusions drawn of tritium balance in light water reactors

International Nuclear Information System (INIS)

Dolle, L.; Bazin, J.

1978-01-01

In the tritium balance of pressurized water reactors, using boric acid and lithium in the cooling water, contribution of the tritium produced by fission, diffusing through the zircalloy of the fuel cladding estimated to 0.1%, was not in agreement with quantities measured in reactors. It is still difficult to estimate what percentage is represented by the tritium formed by fission in the fuel, owing to diffusion through cladding. The tritium balance in different working nuclear power stations is consequently of interest. The tritium balance method in the water of the cooling circuit of PWR is fast and experimentally simple. It is less sensitive to errors originating from fission yields than balance of tritium produced by fission in the fuel. A tritium balance in the water of the cooling circuit of Biblis-A, with a specific burn-up of 18000 MWd/t gives a better precision. Diffusion rate of tritium produced by fission was less than 0.2%. So low a contribution is a justification to the use of lithium with an isotopic purity of 99.9% of lithium 7 to limit at a low value the residual lithium 6 [fr

C-Reactor I and E loading instability limits

Energy Technology Data Exchange (ETDEWEB)

Hess, K.W.

1957-01-24

The pilot charging of I & E fuel elements has been implemented at C-Reactor under Production Test IP-19-A. It was necessary to provide adequate tube protection against flow interruption by establishing proper trip setting on the Panellit pressure gauges. the administration of these Panellit trip settings is done by trip-before- boiling tube outlet temperature limits, which are similar in principle to the current instability limits. Trip-before-boiling limits for C-Reactor I & E fuel elements loadings are presented in this document.

Tasks for development of SiC/SiC composites as structural material in a fusion reactor

International Nuclear Information System (INIS)

Yamada, Reiji

1997-01-01

SiC/SiC composites are chosen for a structural material of blankets in DREAM Reactor that has been proposed as a power reactor by JAERI. The main requirements and the target values in the DREAM conceptual design were described, and compared to available experimental data. (author)

Prototype tokamak fusion reactor based on SiC/SiC composite material focusing on easy maintenance

International Nuclear Information System (INIS)

Nishio, S.; Ueda, S.; Kurihara, R.; Kuroda, T.; Miura, H.; Sako, K.; Takase, H.; Seki, Y.; Adachi, J.; Yamazaki, S.; Hashimoto, T.; Mori, S.; Shinya, K.; Murakami, Y.; Senda, I.; Okano, K.; Asaoka, Y.; Yoshida, T.

2000-01-01

If the major part of the electric power demand is to be supplied by tokamak fusion power plants, the tokamak reactor must have an ultimate goal, i.e. must be excellent in construction cost, safety aspect and operational availability (maintainability and reliability), simultaneously. On way to the ultimate goal, the approach focusing on the safety and the availability (including reliability and maintainability) issues must be the more promising strategy. The tokamak reactor concept with the very high aspect ratio configuration and the structural material of SiC/SiC composite is compatible with this approach, which is called the DRastically Easy Maintenance (DREAM) approach. This is because SiC/SiC composite is a low activation material and an insulation material, and the high aspect ratio configuration leads to a good accessibility for the maintenance machines. As the intermediate steps along this strategy between the experimental reactor such as international thermonuclear experimental reactor (ITER) and the ultimate goal, a prototype reactor and an initial phase commercial reactor have been investigated. Especially for the prototype reactor, the material and technological immaturities are considered. The major features of the prototype and commercial type reactors are as follows. The fusion powers of the prototype and the commercial type are 1.5 and 5.5 GW, respectively. The major/minor radii for the prototype and the commercial type are of 12/1.5 m and 16/2 m, respectively. The plasma currents for the prototype and the commercial type are 6 and 9.2 MA, respectively. The coolant is helium gas, and the inlet/outlet temperatures of 500/800 and 600/900 deg. C for the prototype and the commercial type, respectively. The thermal efficiencies of 42 and 50% are obtainable in the prototype and the commercial type, respectively. The maximum toroidal field strengths of 18 and 20 tesla are assumed in the prototype and the commercial type, respectively. The thermal

Nuclear design for high temperature gas cooled reactor (GTHTR300C) using MOX fuel

International Nuclear Information System (INIS)

Mouri, Tomoaki; Kunitomi, Kazuhiko

2008-01-01

A design study of the hydrogen cogeneration high temperature gas cooled reactor (GTHTR300C) that can produce both electricity and hydrogen has been carried out in Japan Atomic Energy Agency. The GTHTR300C is the system with thermal power of 600MW and reactor outlet temperature of 950degC, which is expected to supply the hydrogen to fuel cell vehicles after 2020s. In future, the full deployment of fast reactor cycle without natural uranium will demand the use of Mixed-Oxide (MOX) fuels in the GTHTR300C. Therefore, a nuclear design was performed to confirm the feasibility of the reactor core using MOX fuels. The designed reactor core has high performance and meets safety requirements. In this paper, the outline of the GTHTR300C and the nuclear design of the reactor core using MOX fuels are described. (author)

Project management plan for Reactor 105-C Interim Safe Storage project

International Nuclear Information System (INIS)

Plagge, H.A.

1996-09-01

Reactor 105-C (located on the Hanford Site in Richland, Washington) will be placed into an interim safe storage condition such that (1) interim inspection can be limited to a 5-year frequency; (2) containment ensures that releases to the environmental are not credible under design basis conditions; and (3) final safe storage configuration shall not preclude or significantly increase the cost for any decommissioning alternatives for the reactor assembly.This project management plan establishes plans, organizational responsibilities, control systems, and procedures for managing the execution of Reactor 105-C interim safe storage activities to meet programmatic requirements within authorized funding and approved schedules

Building reactor operator sustain expert system with C language integrated production system

International Nuclear Information System (INIS)

Ouyang Qin; Hu Shouyin; Wang Ruipian

2002-01-01

The development of the reactor operator sustain expert system is introduced, the capability of building reactor operator sustain expert system is discussed with C Language Integrated Production System (Clips), and a simple antitype of expert system is illustrated. The limitation of building reactor operator sustain expert system with Clips is also discussed

Neutronics and thermohydraulics of the reactor C.E.N.E.-Part I; Analisis neutronico y termohidraulico del reactor C.E.N.E. Parte I

Energy Technology Data Exchange (ETDEWEB)

Caro, R; Ahnert, C; Naudin, A E; Martinez Fanegas, R; Minguez, E; Rovira, A

1976-07-01

In this report the analysis of neutronics (both statics and kinetics), of the 10 MWt swimming pool reactor C.E.N.E, is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking, carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs.

Neutronics and thermohydraulics of the reactor C.E.N.E. Part II; Analisis neutronico y termohidraulico del reactor C.E.N.E. Parte II

Energy Technology Data Exchange (ETDEWEB)

Caro, R

1976-07-01

In this report the analysis of neutronics thermohydraulics and shielding of the 10 HWt swimming pool reactor C.E.N.E is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs.

Qualification of SiC materials for fusion and fission reactors

International Nuclear Information System (INIS)

Ryazanov, Alexander

2009-01-01

Ceramic materials such as silicon carbide (SiC) and SiC/SiC composites are both considered, due to their high-temperature strength, pseudo-ductile fracture behavior and low-induced radioactivity, as candidate materials for fusion reactor (test blanket module for ITER) and high temperature gas-cooled reactors (HTGR). The radiation swelling and creep of SiC are very important physical phenomena that determine the radiation resistance of them in these reactors. Other important problem which exists especially in fusion reactor is an effect of accumulation of high concentrations of helium atoms in SiC (up to 15000-20000 at.ppm) due to (n,α) nuclear reaction on physical mechanical properties. An understanding of the physical mechanism of this phenomenon is very important for the investigations of helium atom effect on radiation swelling in SiC. In this report a compilation of non-irradiated and irradiated properties of SiC are provided and analyzed in terms of their application to fusion and high temperature gas cooled reactors. Special topic of this report is oriented on the micro structural changes in chemically vapor-deposited (CVD) high-purity beta-SiC during neutron and ion irradiations at elevated temperatures. The evolutions of various radiation induced defects including dislocation loops, network dislocations and cavities are presented here as a function of irradiation temperature and fluencies. These observations are discussed in relation with such irradiation phenomena in SiC as low temperature swelling and cavity swelling. One of the main difficulties in the radiation damage studies of SiC materials lies in the absence of theoretical models and interpretation of many physical mechanisms of radiation phenomena including the radiation swelling and creep. The point defects in ceramic materials are characterized by the charge states and they can have an effective charge. The internal effective electrical field is formed due to the accumulation of charged point

Characterization of 14C in Swedish light water reactors.

Science.gov (United States)

Magnusson, Asa; Aronsson, Per-Olof; Lundgren, Klas; Stenström, Kristina

2008-08-01

This paper presents the results of a 4-y investigation of 14C in different waste streams of both boiling water reactors (BWRs) and pressurized water reactors (PWRs). Due to the potential impact of 14C on human health, minimizing waste and releases from the nuclear power industry is of considerable interest. The experimental data and conclusions may be implemented to select appropriate waste management strategies and practices at reactor units and disposal facilities. Organic and inorganic 14C in spent ion exchange resins, process water systems, ejector off-gas and replaced steam generator tubes were analyzed using a recently developed extraction method. Separate analysis of the chemical species is of importance in order to model and predict the fate of 14C within process systems as well as in dose calculations for disposal facilities. By combining the results of this investigation with newly calculated production rates, mass balance assessments were made of the 14C originating from production in the coolant. Of the 14C formed in the coolant of BWRs, 0.6-0.8% was found to be accumulated in the ion exchange resins (core-specific production rate in the coolant of a 2,500 MWth BWR calculated to be 580 GBq GW(e)(-1) y(-1)). The corresponding value for PWRs was 6-10% (production rate in a 2,775 MWth PWR calculated to be 350 GBq GW(e)(-1) y(-1)). The 14C released with liquid discharges was found to be insignificant, constituting less than 0.5% of the production in the coolant. The stack releases, routinely measured at the power plants, were found to correspond to 60-155% of the calculated coolant production, with large variations between the BWR units.

A new SiC/C bulk FGM for fusion reactor

International Nuclear Information System (INIS)

Changchun, G.; Anhua, W.; Wenbin, C.; Jiangtao, L.

2001-01-01

Graphite is widely used in present Tokamak facilities and a C/C composite has been selected as one of the candidate materials for the ITER. But C-based material has an excessive chemical sputtering yield at 600-1000 K and exhibits irradiation enhanced sublimation at >1200 K under plasma erosion condition, causing serious C-contamination of plasma. Low Z material SiC has several advantages for use in fusion reactor, such as excellent high temperature properties, corrosion resistance, low density, and especially its low activation irradiation. To reduce C contamination during plasma exposure, previously SiC coatings were chemically deposited on the surface of C-substrate, however, the thermal stresses arise on the interface between the coating layers and the substrate under high temperature. Heating/cooling cycle leading to cracks in SiC/C interface, small thickness of coating and long processing time are limiting factors for FGM made with CVD process. In this paper, a new SiC/C bulk FGM has been successfully fabricated with P/M hot pressing process. The chemical sputtering yield, gas desorption performance, thermal shock resistance and physical sputtering performance in Tokamak are outlined in this paper. (author)

El presupuesto del municipio del cantón Biblián. Diseño de un sistema para la formulación, ejecución, control y evaluación de presupuestos participativos.

OpenAIRE

Rojas Idrovo, Gladys Eulalia

2011-01-01

Diagnosticar los aspectos administrativos que provocan inconvenientes en la formulación, ejecución, control y evaluación del presupuesto. Este trabajo de investigación tuvo como informantes a autoridades, funcionarios, empleados y trabajadores de la Municipalidad de Biblián y a los Presidentes de las Juntas Parroquiales, y se realizó debido a la necesidad de promover prácticas de participación ciudadana a nivel local que contribuyan a mejorar la calidad de la inversión pública y fortalezca...

Carta do Editor de Encontros Bibli 10.5007/1518-2924.2008v13nesp1pi

Directory of Open Access Journals (Sweden)

Francisco das Chagas de Souza

2008-01-01

dessas medições têm assegurado que sejam escolhidos os países ou localidades que, ao receberem investimentos financeiros, permitam aos proprietários desses extrair o máximo de riqueza, indiferentes das ruínas que possam produzir sobre as populações locais. Esta edição especial monográfica de Encontros Bibli, organizada a quatro mãos por Nair Kobashi, da USP e Raimundo Nonato Macedo dos Santos, da UFSC, consegue reunir o que de melhor se pode refletir, hoje, sobre o tema Métricas da Informação. Nos oito textos apresentados há uma visão larga dos vários ângulos com que o tema é tratado, tanto no Brasil quanto no exterior. A qualidade das contribuições, seguramente dá, aos leitores de Encontros Bibli, um fascículo a ser utilizado como um instrumento indispensável para a compreensão do tema. Mais uma vez, desejamos a toda a audiência de Encontros Bibli, uma excelente leitura e discussão de temática tão atual no cenário da Ciência da Informação e Biblioteconomia, agradecendo o empenho dos organizadores em mobilizar os autores, e sobretudo a estes, por sua dedicação e vontade de socializar o conhecimento que vêm produzindo em suas investigações. Prof. Francisco das Chagas de Souza – Editor chagas@cin.ufsc.br ou bibli@cin.ufsc.br Departamento de Ciência da Informação Programa de Pós-Graduação em Ciência da Informação Universidade Federal de Santa Catarina Brasil Florianópolis, Ilha de Santa Catarina, março de 2008.

Investigation of the burn-up behavior of boron poison rods, placed in a fuel assembly of a pressurized water reactor

International Nuclear Information System (INIS)

Arnold, C.; Lutz, D.C.

1979-09-01

The excess reactivity of a pressurized water reactor is compensated by boron, disolved in the moderator. In addition during the first cycle boron poison rods are placed in fuel assemblies without control rods. The burn-up behavior of a poison rod in a Biblis B fuel assembly is analysed in the present paper. Multigroup spectrum calculations were performed. The influence of critical boron concentration depending from burn-up, the changes of fuel concentration and the concentration of burnable poison were taken into consideration. Furthermore the built-up of rapidly saturating fisson products 135 Xe and 149 Sm was considered. The interaction of these effects are discussed. Spatial influences are emphasized most. Finally two group cross sections were calculated. The results are compared with calculations for a fuel assembly of the same type without burnable poison rods. (orig.) [de

The determination of neutron energy spectrum in reactor core C1 of reactor VR-1 Sparrow

Energy Technology Data Exchange (ETDEWEB)

Vins, M. [Department of Nuclear Reactors, Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University, V Holesovickach 2, 180 00 Prague 8 (Czech Republic)], E-mail: vinsmiro@seznam.cz

2008-07-15

This contribution overviews neutron spectrum measurement, which was done on training reactor VR-1 Sparrow with a new nuclear fuel. Former nuclear fuel IRT-3M was changed for current nuclear fuel IRT-4M with lower enrichment of 235U (enrichment was reduced from former 36% to 20%) in terms of Reduced Enrichment for Research and Test Reactors (RERTR) Program. Neutron spectrum measurement was obtained by irradiation of activation foils at the end of pipe of rabit system and consecutive deconvolution of obtained saturated activities. Deconvolution was performed by computer iterative code SAND-II with 620 groups' structure. All gamma measurements were performed on Canberra HPGe. Activation foils were chosen according physical and nuclear parameters from the set of certificated foils. The Resulting differential flux at the end of pipe of rabit system agreed well with typical spectrum of light water reactor. Measurement of neutron spectrum has brought better knowledge about new reactor core C1 and improved methodology of activation measurement. (author)

Production and release of {sup 14}C from a swimming pool reactor

Energy Technology Data Exchange (ETDEWEB)

Krishnamoorthy, T M [Bhabha Atomic Research Centre, Mumbai (India). Environmental Assessment Div.; Sadarangani, S H [Bhabha Atomic Research Centre, Mumbai (India). Radiation Safety Systems Div.; Doshi, G R [Bhabha Atomic Research Centre, Bombay (India). Health Physics Div.

1994-04-01

The annual production rate of {sup 14}C in the Apsara swimming pool reactor works out to be about 2.94 mCi. The concentration distribution of {sup 14}C in different compartments viz. pool water, reactor hall air and ion-exchange resin ranged from 200 to 440 pCi/l, 0.09 to 0.38 pCi/l, an average concentration of 8.16 pCi/g respectively. The mean residence time of {sup 14}C in pool water is evaluated to be about 7 days taking into account various sinks. The study revealed atmospheric exchange at the air-water interface as the dominant process responsible for the loss of {sup 14}C from the pool water. (author). 7 refs., 2 figs., 4 tabs.

Upgrade of VR-1 training reactor I and C

International Nuclear Information System (INIS)

Kropik, M.; Matejka, K.; Chab, V.

2003-01-01

The contribution describes the upgrade of the VR-1 training reactor I and C (Instrumentation and Control). The reactor was put into operation in the 1990, and its I and C seems to be obsolete now. The new I and C utilises the same digital technology as the old one. The upgrade has been done gradually during holidays in order not to disturb the reactor utilisation during teaching and training. The first stage consisted in the human-machine interface and the control room upgrade in 2001. A new operator's desk, displays, indicators and buttons were installed. Completely new software and communication interface to the present I and C were developed. During the second stage in 2002, new control rod drivers and safety circuits were installed. The rod motors were replaced and necessary mechanical changes on the control rod mechanism, induced by the utilisation of the new motor, were done. The new safety circuits utilise high quality relays with forced contacts to guarantee high reliability of their operation. The third stage, the control system upgrade is being carried out now. The new control system is based on an industrial PC mounted in a 19 inch crate. The operating system of the PC is the Microsoft Windows XP with the real time support RTX of the VentureCom Company. A large amount of work has been devoted to the software requirements to specify all dependencies, modes and permitted actions, safety measures, etc. The Department took an active part in the setting of software requirements and later in verification and validation of the software and the whole control system. Finally, a new protection system consisting of power measuring and power protection channels will be installed in 2004 or 2005. (author)

Determination of the NPP Krsko reactor core safety limits using the COBRA-III-C code

International Nuclear Information System (INIS)

Lajtman, S.; Feretic, D.; Debrecin, N.

1989-01-01

This paper presents the NPP Krsko reactor core safety limits determined by the COBRA-III-C code, along with the methodology used. The reactor core safety limits determination is a part of reactor protection limits procedure. The results obtained were compared to safety limits presented in NPP Krsko FSAR. The COBRA-III-C NPP Krsko design core steady state thermal hydraulics calculation, used as the basis for the safety limits calculation, is presented as well. (author)

Engineering and planning for reactor 105-C interim safe storage project subcontract no. 0100C-SC-G0001 conceptual design report. Volume 1

International Nuclear Information System (INIS)

1996-04-01

The 105-C Reactor, one of eight surplus production reactors at the Hanford Site, has been proposed by the U.S. Department of Energy, Richland, Operations Office to be the first large-scale technology demonstration project in the decontamination and decommissioning (D ampersand D) focus area as part of the project for dismantlement and interim safe storage. The 105-C Reactor will be placed in an interim safe storage condition, then undergo the decontamination and decommissioning phase. After D ampersand D, the reactor will be placed in long- term safe storage. This report provides the conceptual design for these activities

Joining of SiCf/SiC composites for thermonuclear fusion reactors

International Nuclear Information System (INIS)

Ferraris, M.; Badini, C.; Montorsi, M.; Appendino, P.; Scholz, H.W.

1994-01-01

Due to their favourable radiological behaviour, SiC f /SiC composites are promising structural materials for future use in fusion reactors. A problem to cope with is the joining of the ceramic composite material (CMC) to itself for more complex structures. Maintenance concepts for a reactor made of SiC f /SiC will demand a method of joining. The joining agents should comply with the low-activation approach of the base material. With the acceptable elements Si and Mg, sandwich structures of composite/metal/composite were prepared in Ar atmosphere at temperatures just above the melting points of the metals. Another promising route is the use of joining agents of boro-silicate glasses: their composition can be tailored to obtain softening temperatures of interest for fusion applications. The glassy joint can be easily ceramised to improve thermomechanical properties. The joining interfaces were investigated by SEM-EDS, XRD and mechanical tests. ((orig.))

Calibration of new I and C at VR-1 training reactor

International Nuclear Information System (INIS)

Kropik, Martin; Jurickova, Monika

2011-01-01

The paper describes a calibration of the new instrumentation and control (I and C) at the VR-1 training reactor in Prague. The I and C uses uncompensated fission chambers for the power measurement that operate in a pulse or a DC current and a Campbell regime, according to the reactor power. The pulse regime uses discrimination for the avoidance of gamma and noise influence of the measurement. The DC current regime employs a logarithmic amplifier to cover the whole reactor DC current power range with only one electronic circuit. The system computer calculates the real power from the logarithmic data. The Campbell regime is based on evaluation of the root mean square (RMS) value of the neutron noise. The calculated power from Campbell range is based on the square value of the RMS neutron noise data. All data for the power calculation are stored in computer flash memories. To set proper data there, it was necessary to carry out the calibration of the I and C. At first, the proper discrimination value was found while examining the spectrum of the neutron signal from the chamber. The constants for the DC current and Campbell calculations were determined from an independent reactor power measurement. The independent power measuring system that was used for the calibration was accomplished by a compensated current chamber with an electrometer. The calculated calibration constants were stored in the computer flash memories, and the calibrated system was again successfully compared with the independent power measuring system. Finally, proper gamma discrimination of the Campbell system was carefully checked.

Neutronics and thermohydraulics of the reactor C.E.N.E. Pt. 1

International Nuclear Information System (INIS)

Caro, R.; Ahnert, C.; Esteban Naudin, A.; Martinez Fanegas, R.; Minguez, E.; Rovira, A.

1976-01-01

The analysis of neutronics (both statics and kinetics), of the 10 Mwt swimming pool reactor C.E.N.E. is included. A short description of the theoretical model used, along with the theoretical versus experimental cheking, carried out, whenever possible, with the reactors JEN-1 and JEN-2 of Junta de Energia Nuclear, is given in each of these chapters. (author) [es

Project management plan for the 105-C Reactor interim safe storage project. Revision 1

International Nuclear Information System (INIS)

Miller, R.L.

1997-01-01

In 1942, the Hanford Site was commissioned by the US Government to produce plutonium. Between 1942 and 1955, eight water-cooled, graphite-moderated reactors were constructed along the Columbia River at the Hanford Site to support the production of plutonium. The reactors were deactivated from 1964 to 1971 and declared surplus. The Surplus Production Reactor Decommissioning Project (BHI 1994b) will decommission these reactors and has selected the 105-C Reactor to be used as a demonstration project for interim safe storage at the present location and final disposition of the entire reactor core in the 200 West Area. This project will result in lower costs, accelerated schedules, reduced worker exposure, and provide direct benefit to the US Department of Energy for decommissioning projects complex wide. This project sets forth plans, organizational responsibilities, control systems, and procedures to manage the execution of the Project Management Plan for the 105-C Reactor Interim Safe Storage Project (Project Management Plan) activities to meet programmatic requirements within authorized funding and approved schedules. The Project Management Plan is organized following the guidelines provided by US Department of Energy Order 4700.1, Project Management System and the Richland Environmental Restoration Project Plan (DOE-RL 1992b)

Advanced Reactor Licensing: Experience with Digital I&C Technology in Evolutionary Plants

Energy Technology Data Exchange (ETDEWEB)

Wood, RT

2004-09-27

This report presents the findings from a study of experience with digital instrumentation and controls (I&C) technology in evolutionary nuclear power plants. In particular, this study evaluated regulatory approaches employed by the international nuclear power community for licensing advanced l&C systems and identified lessons learned. The report (1) gives an overview of the modern l&C technologies employed at numerous evolutionary nuclear power plants, (2) identifies performance experience derived from those applications, (3) discusses regulatory processes employed and issues that have arisen, (4) captures lessons learned from performance and regulatory experience, (5) suggests anticipated issues that may arise from international near-term deployment of reactor concepts, and (6) offers conclusions and recommendations for potential activities to support advanced reactor licensing in the United States.

Physicochemical interactions resulting from the use of a SiC/SiC composite material in typical environments of future nuclear reactors

International Nuclear Information System (INIS)

Braun, James

2014-01-01

The development of high purity SiC fibers during the nineties has led to their consideration as nuclear reactors components through the use of SiC/SiC composites. SiC and SiC/SiC composites are considered as core materials of future nuclear reactors (SFR, GFR) and as a potential replacement for the zirconium cladding of PWR. Therefore, the thermochemical compatibility of these materials with typical environments of those nuclear reactors has been studied. The composition and the growth kinetics of the reaction zone of SiC towards niobium and tantalum (considered as materials to ensure the leak-tightness of a SiC/SiC cladding for GFR) have been studied between 1050 and 1500 C. High temperature heat treatments in open and closed systems between SiC and UO 2 have shown a significant reactivity over 1200 C characterized by the formation of CO and uranium silicides. Moreover, a liquid phase has been detected between 1500 and 1650 C. The exposure of SiC/SiC to liquid sodium (550 C, up to 2000 h) has been studied as a function of the oxygen concentration dissolved in liquid sodium. An improvement of the mechanical properties of the composites elaborated for this study (increase of the tensile strength and strain at failure) has been highlighted after immersion in the liquid sodium independently of its oxygen concentration. It is believed that this phenomenon is due to the presence of residual sodium in the material. (author) [fr

Application of non-destructive testing and in-service inspections to research reactors and preparation of ISI programme and manual for WWR-C research reactors

International Nuclear Information System (INIS)

Khattab, M.

1996-01-01

The present report gives a review on the results of application of non-destructive testing and in-service inspections to WWR-C reactors in different countries. The major problems related to reactor safety and the procedure of inspection techniques are investigated to collect the experience gained from this type of reactors. Exchangeable experience in solving common problems in similar reactors play an important role in the effectiveness of their rehabilitation programmes. 9 figs., 4 tabs

Neutronics and thermohydraulics of the reactor C.E.N.E. Part II

International Nuclear Information System (INIS)

Caro, R.

1976-01-01

In this report the analysis of neutronics thermohydraulics and shielding of the 10 HWt swimming pool reactor C.E.N.E is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs

Neutronics and thermohydraulics of the reactor C.E.N.E.-Part I

International Nuclear Information System (INIS)

Caro, R.; Ahnert, C.; Naudin, A. E.; Martinez Fanegas, R.; Minguez, E.; Rovira, A.

1976-01-01

In this report the analysis of neutronics (both statics and kinetics), of the 10 MWt swimming pool reactor C.E.N.E, is included. In each of these chapters is given a short description of the theoretical model used, along with the theoretical versus experimental checking, carried out, whenever possible, with the reactors JEN-I and JEN-II of Junta de Energia Nuclear. (Author) 11 refs

Carta do editor de edições especiais da Encontros Bibli 10.5007/1518-2924.2011v16nesp1piv

Directory of Open Access Journals (Sweden)

Francisco das Chagas de Souza

2011-06-01

Full Text Available Dos horizontes arquivísticos e de seu sentido É significativo observar que a discussão sobre Arquivologia e sobre as práticas profissionais arquivisticas tem avançado muito nos últimos anos no Brasil, e as razões são claramente apontadas pelos organizadores desta edição especial de Encontros Bibli em seu texto editorial. Contendo sete artigos, esta edição temática traz o título Horizontes Arquivísticos.Para dar vida a este número, foi desenvolvido um trabalho de quase dois anos, liderado pelo pesquisador José Maria Jardim e colaboração de Renata Silva Borges. Aqui estão reunidos nove autores e seis avaliadores, todos vinculados a instituições de ensino e de pesquisa ligadas ao Serviço Público Federal, com sede nas cidades de Brasilia, Rio de Janeiro, Niteroi e Florianópolis: UNB, UNIRIO, UFF, UFRJ, UFSC, Arquivo Nacional e FIOCRUZ.Neste momento da história brasileira ─ em que se anunciam políticas governamentais em prol da cidadania, em que se diz da disposição de resgate da verdade sobre os fatos políticos acontecidos na gestão do estado brasileiro dos anos de 1964 a 1989 ─ os arquivos e seus profissionais passam a divisar um relevante protagonismo. Pode-se dizer que, de certa maneira, deu-se um movimento de preparação deste protagonismo e que, simultaneamente, essa preparação alicerçou a percepção de segmentos importantes do setor público para oferecer essa perspectiva para a sociedade nacional.Nesse sentido, tem peso relevante a instalação de novos cursos de bacharelado na área, totalizando, em 2011, o número de 14 universidades que os oferecem: UNIRIO, UFF, UFSM, UFES, UNB, UEL, UFBA ,UNESP/MARÍLIA, UFRGS, UEPB, UFAM, FURG, UFMG, UFSC. Uma nota marcante é que todas essas Instituições de Ensino Superior têm vínculos governamentais, sendo onze federais e três estaduais. Esse movimento não se faz por outro caminho senão o da pesquisa histórica e social. Em áreas como a História, Educa

10 CFR 72.108 - Spent fuel, high-level radioactive waste, or reactor-related greater than Class C waste...

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Spent fuel, high-level radioactive waste, or reactor... RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C WASTE Siting Evaluation Factors § 72.108 Spent fuel, high-level radioactive waste, or reactor-related greater than Class C waste transportation. The...

Performance and microbial community composition dynamics of aerobic granular sludge from sequencing batch bubble column reactors operated at 20 degrees C, 30 degrees C, and 35 degrees C.

Science.gov (United States)

Ebrahimi, Sirous; Gabus, Sébastien; Rohrbach-Brandt, Emmanuelle; Hosseini, Maryam; Rossi, Pierre; Maillard, Julien; Holliger, Christof

2010-07-01

Two bubble column sequencing batch reactors fed with an artificial wastewater were operated at 20 degrees C, 30 degrees C, and 35 degrees C. In a first stage, stable granules were obtained at 20 degrees C, whereas fluffy structures were observed at 30 degrees C. Molecular analysis revealed high abundance of the operational taxonomic unit 208 (OTU 208) affiliating with filamentous bacteria Leptothrix spp. at 30 degrees C, an OTU much less abundant at 20 degrees C. The granular sludge obtained at 20 degrees C was used for the second stage during which one reactor was maintained at 20 degrees C and the second operated at 30 degrees C and 35 degrees C after prior gradual increase of temperature. Aerobic granular sludge with similar physical properties developed in both reactors but it had different nutrient elimination performances and microbial communities. At 20 degrees C, acetate was consumed during anaerobic feeding, and biological phosphorous removal was observed when Rhodocyclaceae-affiliating OTU 214 was present. At 30 degrees C and 35 degrees C, acetate was mainly consumed during aeration and phosphorous removal was insignificant. OTU 214 was almost absent but the Gammaproteobacteria-affiliating OTU 239 was more abundant than at 20 degrees C. Aerobic granular sludge at all temperatures contained abundantly the OTUs 224 and 289 affiliating with Sphingomonadaceae indicating that this bacterial family played an important role in maintaining stable granular structures.

Irradiation capsule for testing magnetic fusion reactor first-wall materials at 60 and 2000C

International Nuclear Information System (INIS)

Conlin, J.A.

1985-08-01

A new type of irradiation capsule has been designed, and a prototype has been tested in the Oak Ridge Research Reactor (ORR) for low-temperature irradiation of Magnetic Fusion Reactor first-wall materials. The capsule meets the requirements of the joint US/Japanese collaborative fusion reactor materials irradiation program for the irradiation of first-wall fusion reactor materials at 60 and 200 0 C. The design description and results of the prototype capsule performance are presented

Study on Optimization of I and C Architecture for Research Reactors Using Bayesian Networks

Energy Technology Data Exchange (ETDEWEB)

Rahman, Khaili Ur; Shin, Jinsoo; Heo, Gyunyoung [Kyung Hee Univ., Yongin (Korea, Republic of)

2013-07-01

The optimization in terms of redundancy of modules and components in Instrumentation and Control (I and C) architecture is based on cost and availability assuming regulatory requirements are satisfied. The motive of this study is to find an optimized I and C architecture, either in hybrid formation, fully digital or analog, with respect to system availability and relative cost of architecture. The cost of research reactors I and C systems is prone to have effect on marketing competitiveness. As a demonstrative example, the reactor protection system of research reactors is selected. The four cases with different architecture formation were developed with single and double redundancy of bi-stable modules, coincidence processor module, and safety or protection circuit actuation logic. The architecture configurations are transformed to reliability block diagram (RBD) based on logical operation and function of modules. A Bayesian Network (BN) model is constructed from RBD to assess availability. The cost estimation was proposed and reliability cost index RI was suggested.

Study on Optimization of I and C Architecture for Research Reactors Using Bayesian Networks

International Nuclear Information System (INIS)

Rahman, Khaili Ur; Shin, Jinsoo; Heo, Gyunyoung

2013-01-01

The optimization in terms of redundancy of modules and components in Instrumentation and Control (I and C) architecture is based on cost and availability assuming regulatory requirements are satisfied. The motive of this study is to find an optimized I and C architecture, either in hybrid formation, fully digital or analog, with respect to system availability and relative cost of architecture. The cost of research reactors I and C systems is prone to have effect on marketing competitiveness. As a demonstrative example, the reactor protection system of research reactors is selected. The four cases with different architecture formation were developed with single and double redundancy of bi-stable modules, coincidence processor module, and safety or protection circuit actuation logic. The architecture configurations are transformed to reliability block diagram (RBD) based on logical operation and function of modules. A Bayesian Network (BN) model is constructed from RBD to assess availability. The cost estimation was proposed and reliability cost index RI was suggested

Basic safety principles of KLT-40C reactor plants

International Nuclear Information System (INIS)

Beliaev, V.; Polunichev, V.

2000-01-01

The KLT-40 NSSS has been developed for a floating power block of a nuclear heat and power station on the basis of ice-breaker-type NSSS (Nuclear Steam Supply System) with application of shipbuilding technologies. Basic reactor plant components are pressurised water reactor, once-through coil-type steam generator, primary coolant pump, emergency protection rod drive mechanisms of compensate group-electromechanical type. Basic RP components are incorporated in a compact steam generating block which is arranged within metal-water shielding tank's caissons. Domestic regulatory documents on safety were used for the NSSS design. IAEA recommendations were also taken into account. Implementation of basic safety principles adopted presently for nuclear power allowed application of the KLT-40C plant for a floating power unit of a nuclear co-generation station. (author)

Experience with safety assessment of digital upgrading of IandC in VVER type reactors

International Nuclear Information System (INIS)

Wach, D.; Mulka, B.; Schnuerer, G.

1997-01-01

The digital upgrading of IandC systems important to safety in WWER type reactors requires a broad expertise in various knowledge fields. The approach of the Institute for safety Technology to the qualification and categorization of safety-critical software systems is highlighted. The role of the Institute in the qualification of the Teleperm XS and the type testing of its components is described. The aspects of the safety assessment of digital IandC systems in WWER type reactors is discussed in some detail. (A.K.)

Advanced Reactor Licensing: Experience with Digital I and C Technology in Evolutionary Plants

International Nuclear Information System (INIS)

Wood, RT

2004-01-01

This report presents the findings from a study of experience with digital instrumentation and controls (I and C) technology in evolutionary nuclear power plants. In particular, this study evaluated regulatory approaches employed by the international nuclear power community for licensing advanced l and C systems and identified lessons learned. The report (1) gives an overview of the modern l and C technologies employed at numerous evolutionary nuclear power plants, (2) identifies performance experience derived from those applications, (3) discusses regulatory processes employed and issues that have arisen, (4) captures lessons learned from performance and regulatory experience, (5) suggests anticipated issues that may arise from international near-term deployment of reactor concepts, and (6) offers conclusions and recommendations for potential activities to support advanced reactor licensing in the United States

SiC epitaxial layer growth in a novel multi-wafer VPE reactor

Energy Technology Data Exchange (ETDEWEB)

Burk, A.A. Jr.; O`Loughlin, M.J. [Northrop Grumman Advanced Technology Lab., Baltimore, MD (United States); Mani, S.S. [Northrop Grumman Science and Technology Center, Pittsburgh, PA (United States)

1998-06-01

Preliminary results are presented for SiC epitaxial layer growth employing a unique planetary SiC-VPE reactor. The high-throughput, multi-wafer (7 x 2-inch) reactor, was designed for atmospheric and reduced pressure operation at temperatures up to and exceeding 1600 C. Specular epitaxial layers have been grown in the reactor at growth rates from 3-5 {mu}m/hr. The thickest layer grown to data was 42 {mu}m. The layers exhibit minimum unintentional n-type doping of {proportional_to}1 x 10{sup 15} cm{sup -3}, room temperature mobilities of {proportional_to}1000 cm{sup 2}/Vs, and intentional n-type doping from {proportional_to}5 x 10{sup 15} cm{sup -3} to >1 x 10{sup 19} cm{sup -3}. Intrawafer thickness and doping uniformities of 4% and 7% (standard deviation/mean) have been obtained, respectively, on 35 mm diameter substrates. Recently, 3% thickness uniformity has been demonstrated on a 50 mm substrate. Within a run, wafer-to-wafer thickness deviation is {proportional_to}4-14%. Doping variation is currently larger, ranging as much as a factor of two from the highest to the lowest doped wafer. Continuing efforts to improve the susceptor temperature uniformity and reduce unintentional hydrocarbon generation to improve layer uniformity and reproducibility, are presented. (orig.) 18 refs.

Characterization of 2D-C/C composite for application of very high temperature reactor

International Nuclear Information System (INIS)

Shibata, Taiju; Sumita, Junya; Kunimoto, Eiji; Sawa, Kazuhiro; Makita, Taiyo; Takagi, Takashi; Kim, W.J.; Jung, C.H.; Park, J.Y.

2010-01-01

For in-core components of VHTR (Very High Temperature Reactor), carbon fiber reinforced carbon matrix composite (C/C composite) is one of the major candidate materials. In this study, fracture behaviors of two dimensional (2D-) C/C composites were examined by SENB specimens with four-point bending test. The surface of specimens was observed by a CCD camera during the bending test, and observed by a stereomicroscope before and after the bending test. The following results were obtained through mode-I fracture test. (1) Three types of the composites were evaluated by tentatively using the stress intensity factor equation for metallic materials. The equivalent stress intensity factor of 2D-C/C composite is in the range of 5.9 - 10.0MPa m 1/2 . It was expected that the fracture mechanism for the composite materials could be assessed by this test method. (2) The crack opening displacement-load behavior of C/C composite might depend not only on the propagation of crack but also on delaminating between layers. (author)

105-C Reactor interim safe storage project technology integration plan

International Nuclear Information System (INIS)

Pulsford, S.K.

1997-01-01

The 105-C Reactor Interim Safe Storage Project Technology Integration Plan involves the decontamination, dismantlement, and interim safe storage of a surplus production reactor. A major goal is to identify and demonstrate new and innovative D and D technologies that will reduce costs, shorten schedules, enhance safety, and have the potential for general use across the RL complex. Innovative technologies are to be demonstrated in the following areas: Characterization; Decontamination; Waste Disposition; Dismantlement, Segmentation, and Demolition; Facility Stabilization; and Health and Safety. The evaluation and ranking of innovative technologies has been completed. Demonstrations will be selected from the ranked technologies according to priority. The contractor team members will review and evaluate the demonstration performances and make final recommendations to DOE

Study of the obtainment of Mo_2C by gas-solid reaction in a fixed and rotary bed reactor

International Nuclear Information System (INIS)

Araujo, C.P.B. de; Souza, C.P. de; Souto, M.V.M.; Barbosa, C.M.; Frota, A.V.V.M.

2016-01-01

Carbides' synthesis via gas-solid reaction overcomes many of the difficulties found in other processes, requiring lower temperatures and reaction times than traditional metallurgic routes, for example. In carbides' synthesis in fixed bed reactors (FB) the solid precursor is permeated by the reducing/carburizing gas stream forming a packed bed without mobility. The use of a rotary kiln reactor (RK) adds a mixing character to this process, changing its fluid-particle dynamics. In this work ammonium molybdate was subjected to carbo-reduction reaction (CH4 / H2) in both reactors under the same gas flow (15L / h) and temperature (660 ° C) for 180 minutes. Complete conversion was observed Mo2C (dp = 18.9nm modal particles sizes' distribution) in the fixed bed reactor. In the RK reactor this conversion was only partial (∼ 40%) and Mo2C and MoO3 (34nm dp = bimodal) could be observed on the produced XRD pattern. Partial conversion was attributed to the need to use higher solids loading in the reactor CR (50% higher) to avoid solids to centrifuge. (author)

Creep crack growth in a reactor pressure vessel steel at 360 deg C

Energy Technology Data Exchange (ETDEWEB)

Wu, Rui; Seitisleam, F; Sandstroem, R [Swedish Institute for Metals Research, Stockholm (Sweden)

1999-12-31

Plain creep (PC) and creep crack growth (CCG) tests at 360 deg C and post metallography were carried out on a low alloy reactor pressure vessel steel (ASTM A508 class 2) with different microstructures. Lives for the CCG tests were shorter than those for the PC tests and this is more pronounced for simulated heat affected zone microstructure than for the parent metal at longer lives. For the CCG tests, after initiation, the cracks grew constantly and intergranularly before they accelerated to approach rupture. The creep crack growth rate is well described by C*. The relations between reference stress, failure time and steady crack growth rate are presented for the CCG tests. It is demonstrated that the failure stress due to CCG is considerably lower than the yield stress at 360 deg C. Consequently, the CCG will control the static strength of a reactor vessel. (orig.) 17 refs.

Creep crack growth in a reactor pressure vessel steel at 360 deg C

Energy Technology Data Exchange (ETDEWEB)

Rui Wu; Seitisleam, F.; Sandstroem, R. [Swedish Institute for Metals Research, Stockholm (Sweden)

1998-12-31

Plain creep (PC) and creep crack growth (CCG) tests at 360 deg C and post metallography were carried out on a low alloy reactor pressure vessel steel (ASTM A508 class 2) with different microstructures. Lives for the CCG tests were shorter than those for the PC tests and this is more pronounced for simulated heat affected zone microstructure than for the parent metal at longer lives. For the CCG tests, after initiation, the cracks grew constantly and intergranularly before they accelerated to approach rupture. The creep crack growth rate is well described by C*. The relations between reference stress, failure time and steady crack growth rate are presented for the CCG tests. It is demonstrated that the failure stress due to CCG is considerably lower than the yield stress at 360 deg C. Consequently, the CCG will control the static strength of a reactor vessel. (orig.) 17 refs.

Irradiation Microstructure of Austenitic Steels and Cast Steels Irradiated in the BOR-60 Reactor at 320°C

Science.gov (United States)

Yang, Yong; Chen, Yiren; Huang, Yina; Allen, Todd; Rao, Appajosula

Reactor internal components are subjected to neutron irradiation in light water reactors, and with the aging of nuclear power plants around the world, irradiation-induced material degradations are of concern for reactor internals. Irradiation-induced defects resulting from displacement damage are critical for understanding degradation in structural materials. In the present work, microstructural changes due to irradiation in austenitic stainless steels and cast steels were characterized using transmission electron microscopy. The specimens were irradiated in the BOR-60 reactor, a fast breeder reactor, up to 40 dpa at 320°C. The dose rate was approximately 9.4x10-7 dpa/s. Void swelling and irradiation defects were analyzed for these specimens. A high density of faulted loops dominated the irradiated-altered microstructures. Along with previous TEM results, a dose dependence of the defect structure was established at 320°C.

Thermophilic (55 - 65°C) and extreme thermophilic (70 - 80°C) sulfate reduction in methanol and formate-fed UASB reactors

NARCIS (Netherlands)

Vallero, M.V.G.; Camarero, E.; Lettinga, G.; Lens, P.N.L.

2004-01-01

The feasibility of thermophilic (55-65 degreesC) and extreme thermophilic (70-80 degreesC) sulfate-reducing processes was investigated in three lab-scale upflow anaerobic sludge bed (UASB) reactors fed with either methanol or formate as the sole substrates and inoculated with mesophilic granular

Surveillance and Maintenance Plan for the 105-C Reactor Safe Storage Enclosure

International Nuclear Information System (INIS)

Logan, T. E.

1998-01-01

This document provides a plan for implementing surveillance and maintenance activities to ensure that the 105-C Reactor Safe Storage Enclosure is maintained in a safe, environmentally secure, and cost-effective manner until subsequent closure during the final disposition phase of decommissioning

Phospholipase C-catalyzed sphingomyelin hydrolysis in a membrane reactor for ceramide production

DEFF Research Database (Denmark)

Zhang, Long; Liang, Shanshan; Hellgren, Lars

2008-01-01

A membrane reactor for the production of ceramide through sphingomyelin hydrolysis with phospholipase C from Clostridium perfringens was studied for the first time. Ceramide has raised a large interest as an active component in both pharmaceutical and cosmetic industry. The enzymatic hydrolysis...

Design issues on using FPGA-based I and C systems in nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Farias, Marcos S.; Carvalho, Paulo Victor R. de; Santos, Isaac Jose A.L. dos; Lacerda, Fabio de, E-mail: msantana@ien.gov.br, E-mail: paulov@ien.gov.br, E-mail: luquetti@ien.gov.br, E-mail: acerda@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Div. de Engenharia Nuclear

2015-07-01

The FPGA (field programmable gate array) is widely used in various fields of industry. FPGAs can be used to perform functions that are safety critical and require high reliability, like in automobiles, aircraft control and assistance and mission-critical applications in the aerospace industry. With these merits, FPGAs are receiving increased attention worldwide for application in nuclear plant instrumentation and control (I and C) systems, mainly for Reactor Protection System (RPS). Reasons for this include the fact that conventional analog electronics technologies are become obsolete. I and C systems of new Reactors have been designed to adopt the digital equipment such as PLC (Programmable Logic Controller) and DCS (Distributed Control System). But microprocessors-based systems may not be simply qualified because of its complex characteristics. For example, microprocessor cores execute one instruction at a time, and an operating system is needed to manage the execution of programs. In turn, FPGAs can run without an operating system and the design architecture is inherently parallel. In this paper we aim to assess these and other advantages, and the limitations, on FPGA-based solutions, considering the design guidelines and regulations on the use of FPGAs in Nuclear Plant I and C Systems. We will also examine some circuit design techniques in FPGA to help mitigate failures and provide redundancy. The objective is to show how FPGA-based systems can provide cost-effective options for I and C systems in modernization projects and to the RMB (Brazilian Multipurpose Reactor), ensuring safe and reliable operation, meeting licensing requirements, such as separation, redundancy and diversity. (author)

Design of first reactor protection system prototype for C A R E M reactor

International Nuclear Information System (INIS)

Azcona, A; Lorenzo, G.; Maciel, F.; Fittipaldi, A

2006-01-01

In this paper we present the design of a prototype of the C A R E M Reactor Protection System, which is implemented on a basis of the digital platform T E L E P E R M X S.The proposed architecture for the Reactor Protection System (R P S) has 4 redundant trains composed by a complete set of sensors, a data acquisition computer and a processing computer.The information from the 4 processing computers goes into to a two voting units with a two out of four (2004) logic and its outputs are combined by a final actuation logic with a voting scheme of one out of two (1002).The prototype is implemented with a unique train.The train inputs are simulated by an Automatic Testing Unit.The pre-established test case or procedure results are fed back into the A T U.The choice of the digital platform T E L E P E R M X S for the R P S implementation allows versatility in the design stage and permits the prototype expansion due to its modular characteristic and the software tools flexibility [es

Examination of Surface Deposits on Oldbury Reactor Core Graphite to Determine the Concentration and Distribution of 14C.

Directory of Open Access Journals (Sweden)

Liam Payne

Full Text Available Pile Grade A graphite was used as a moderator and reflector material in the first generation of UK Magnox nuclear power reactors. As all of these reactors are now shut down there is a need to examine the concentration and distribution of long lived radioisotopes, such as 14C, to aid in understanding their behaviour in a geological disposal facility. A selection of irradiated graphite samples from Oldbury reactor one were examined where it was observed that Raman spectroscopy can distinguish between underlying graphite and a surface deposit found on exposed channel wall surfaces. The concentration of 14C in this deposit was examined by sequentially oxidising the graphite samples in air at low temperatures (450°C and 600°C to remove the deposit and then the underlying graphite. The gases produced were captured in a series of bubbler solutions that were analysed using liquid scintillation counting. It was observed that the surface deposit was relatively enriched with 14C, with samples originating lower in the reactor exhibiting a higher concentration of 14C. Oxidation at 600°C showed that the remaining graphite material consisted of two fractions of 14C, a surface associated fraction and a graphite lattice associated fraction. The results presented correlate well with previous studies on irradiated graphite that suggest there are up to three fractions of 14C; a readily releasable fraction (corresponding to that removed by oxidation at 450°C in this study, a slowly releasable fraction (removed early at 600°C in this study, and an unreleasable fraction (removed later at 600°C in this study.

CANDU reactors with reactor grade plutonium/thorium carbide fuel

Energy Technology Data Exchange (ETDEWEB)

Sahin, Suemer [Atilim Univ., Ankara (Turkey). Faculty of Engineering; Khan, Mohammed Javed; Ahmed, Rizwan [Pakistan Institute of Engineering and Applied Sciences, Islamabad (Pakistan); Gazi Univ., Ankara (Turkey). Faculty of Technology

2011-08-15

Reactor grade (RG) plutonium, accumulated as nuclear waste of commercial reactors can be re-utilized in CANDU reactors. TRISO type fuel can withstand very high fuel burn ups. On the other hand, carbide fuel would have higher neutronic and thermal performance than oxide fuel. In the present work, RG-PuC/ThC TRISO fuels particles are imbedded body-centered cubic (BCC) in a graphite matrix with a volume fraction of 60%. The fuel compacts conform to the dimensions of sintered CANDU fuel compacts are inserted in 37 zircolay rods to build the fuel zone of a bundle. Investigations have been conducted on a conventional CANDU reactor based on GENTILLYII design with 380 fuel bundles in the core. Three mixed fuel composition have been selected for numerical calculation; (1) 10% RG-PuC + 90% ThC; (2) 30% RG-PuC + 70% ThC; (3) 50% RG-PuC + 50% ThC. Initial reactor criticality values for the modes (1), (2) and (3) are calculated as k{sub {infinity}}{sub ,0} = 1.4848, 1.5756 and 1.627, respectively. Corresponding operation lifetimes are {proportional_to} 2.7, 8.4, and 15 years and with burn ups of {proportional_to} 72 000, 222 000 and 366 000 MW.d/tonne, respectively. Higher initial plutonium charge leads to higher burn ups and longer operation periods. In the course of reactor operation, most of the plutonium will be incinerated. At the end of life, remnants of plutonium isotopes would survive; and few amounts of uranium, americium and curium isotopes would be produced. (orig.)

10 CFR 72.128 - Criteria for spent fuel, high-level radioactive waste, reactor-related greater than Class C waste...

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Criteria for spent fuel, high-level radioactive waste, reactor-related greater than Class C waste, and other radioactive waste storage and handling. 72.128... STORAGE OF SPENT NUCLEAR FUEL, HIGH-LEVEL RADIOACTIVE WASTE, AND REACTOR-RELATED GREATER THAN CLASS C...

Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

International Nuclear Information System (INIS)

Flach, G.P.

1999-01-01

A regional groundwater flow model encompassing approximately 100 mi 2 surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department

Present status of SiCf/SiC composites as low-activation structural materials of fusion reactor in Japan

International Nuclear Information System (INIS)

Kohyama, A.; Katoh, Y.; Hasegawa, A.; Noda, T.

2001-01-01

The outline of research subjects on SiCf/SiC composites to apply to the structural components of fusion reactors are described and present status on material development of SiCf/SiC composites in Japan is reviewed. Irradiation experiments of the composites using fission reactors conducted by international collaborations to clarify their radiation response and to optimize the fabrication processes are introduced. (author)

I and C system at TRIGA - ICN reactor after more than 20 years of operation

International Nuclear Information System (INIS)

Ionila, M.; Preda, M.

2002-01-01

An I and C system that is involved in a nuclear safety function has to be itself safe in operation, strictly performing the survey of those parameters, which are linked to the safety function. The precision of such a system is sufficient for the safety function, but for a more accurate evaluation of the in-core experimental phenomena, the presence of a data acquisition and processing system is needed. The two systems must be together taken into account by the reactor operation. The data acquisition and processing system designated for the monitoring of the stationary or the slow-varying processes allow the safety function evaluation from the point of view of the statistics of the effective reactor operation time along a certain period of time. The evaluation of the unscheduled reactor shutdowns determined by those reactor systems having safety functions with the percentage contribution of each system is presented. The data were selected from the annual operation reports for the reactor and the reactor installations in the period 1981-1999

Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.

1999-02-24

A regional groundwater flow model encompassing approximately 100 mi{sup 2} surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department.

C.E.C. - cod for calculus of the evolution fuel for thermal reactors

International Nuclear Information System (INIS)

Biciolla, L.; Marcu, G.; Mociornita, G.

1975-01-01

The study of ''burnup'' into thermal reactor involves two main aspects: the economic one and another regarding the reactor operation, its stability and control. In the CEC-code written in FORTRAN IV language was analysed the change of the isotopic composition of nuclear fuel from thermal reactor during its operation

A qualified safety I and C for application in reactors of all kinds

International Nuclear Information System (INIS)

Stimler, M.

2001-01-01

Advanced I and C systems for nuclear power plants have to meet increasing demands for safety and availability. Specific requirements coming from the nuclear qualification have to be fulfilled. To meet both subjects adequately, Siemens has developed the advanced digital I and C technology for safety applications TELEPERM XS. National and international codes and standards impose special requirements on the safety I and C of a nuclear power plant. These concern: fault tolerance; robustness; qualification. In order to be able to meet these requirements to the full without making operational automation tasks unnecessarily expensive by excessive conservatism, the TELEPERM XS I and C system platform was developed. It is largely based on standard Hardware devices selected for their quality characteristics and adapted by specific design measures. In the Software area a complete new development had to be undertaken in order to meet the stringent qualification requirements. In 1992 the GRS (Gesellschaft fuer Reaktorsicherheit - Association for Reactor Safety) confirmed the suitability and licensibility of the underlying TELEPERM XS concepts. Subsequently, the development and qualification of the system software and the engineering tools as well as the type testing of the hardware components was performed. Operationally proven hardware components were selected for utilization, among others from the system families SIMATIC and SINEC. The first integration tests were performed successfully in mid-1996. Field testing of the first application projects could be finalised in 1997. In many countries, the nuclear industry bases its licensing process for nuclear power plants on the US-NRC procedures. For this reason, and in order to ensure world-wide utilization of the TXS technology, it was decided in 1998 to submit a licensing application to the US-NRC. In May 2000, Siemens has received a Safety Evaluation Report (SER) from the US-NRC approving use of its TELEPERM XS (TXS) platform

Increased SRP reactor power

International Nuclear Information System (INIS)

MacAfee, I.M.

1983-01-01

Major changes in the current reactor hydraulic systems could be made to achieve a total of about 1500 MW increase of reactor power for P, K, and C reactors. The changes would be to install new, larger heat exchangers in the reactor buildings to increase heat transfer area about 24%, to increase H 2 O flow about 30% per reactor, to increase D 2 O flow 15 to 18% per reactor, and increase reactor blanket gas pressure from 5 psig to 10 psig. The increased reactor power is possible because of reduced inlet temperature of reactor coolant, increased heat removal capacity, and increased operating pressure (larger margin from boiling). The 23% reactor power increase, after adjustment for increased off-line time for reactor reloading, will provide a 15% increase of production from P, K, and C reactors. Restart of L Reactor would increase SRP production 33%

Results of the reliability investigations for the design basis accident 'Rupture of a cold primary coolant system'

International Nuclear Information System (INIS)

Hoertner, H.; Nieckau, E.; Spindler, H.

1976-12-01

This report gives a comprehensive presentation of the detailed reliability investigation carried out for the engineered safety features installed to cope with the design basis accident 'Large LOCA' of a German nuclear power plant with pressurized water reactor. The investigation is based on the engineered safety features of the Biblis Nuclear Power Plant, Unit A. The reliability investigation is carried out by means of a fault tree analysis. The influence of common-mode failures is assessed. (orig.) [de

Biohydrogen production from glucose in upflow biofilm reactors with plastic carriers under extreme thermophilic conditions (70(degree)C)

DEFF Research Database (Denmark)

Zheng, H.; Zeng, Raymond Jianxiong; Angelidaki, Irini

2008-01-01

Biohydrogen could efficiently be produced in glucose-fed biofilm reactors filled with plastic carriers and operated at 70°C. Batch experiments were, in addition, conducted to enrich and cultivate glucose-fed extremethermophilic hydrogen producing microorganisms from a biohydrogen CSTR reactor fed...

First experiences from system integration, installation and commissioning of TELEPERM XS for reactor I and C at the Unterweser NPP

International Nuclear Information System (INIS)

Schoerner, O.

1998-01-01

The modernization of Reactor I and C, consisting of reactor limitation system, reactor control system and rod control system, at Unterweser NPP is the pilot application of the state-of-the-art safety I and C system TELEPERM XS. The Unterweser system has been integrated and tested from December 1996 to May 1997 in the Siemens Erlangen test field and has been installed at site in July 1997. For the period from July 1997 to Jul 1998 the new TELEPERM XS based Reactor I and C system will be operated online-open-loop in parallel to the existing system, in order to get information about the long term stability of the system and conduct intensive personnel training. For one selected function ''Power distribution control'' the operator has the possibility to choose between the old controller and the new TELEPERM XS function. During the 1998 outage the TELEPERM XS system will be connected to the process and the old I and C system will be dismantled. This document describes the experiences gathered during system integration in the test field. (author)

ELECTRICAL RESISTANCE HEATING OF SOILS AT C-REACTOR AT THE SAVANNAH RIVER SITE

International Nuclear Information System (INIS)

Blundy, R; Michael Morgenstern, M; Joseph Amari, J; Annamarie MacMurray, A; Mark Farrar, M; Terry Killeen, T

2007-01-01

Chlorinated solvent contamination of soils and groundwater is an endemic problem at the Savannah River Site (SRS), and originated as by-products from the nuclear materials manufacturing process. Five nuclear reactors at the SRS produced special nuclear materials for the nation's defense program throughout the cold war era. An important step in the process was thorough degreasing of the fuel and target assemblies prior to irradiation. Discharges from this degreasing process resulted in significant groundwater contamination that would continue well into the future unless a soil remediation action was performed. The largest reactor contamination plume originated from C-Reactor and an interim action was selected in 2004 to remove the residual trichloroethylene (TCE) source material by electrical resistance heating (ERH) technology. This would be followed by monitoring to determine the rate of decrease in concentration in the contaminant plume. Because of the existence of numerous chlorinated solvent sources around SRS, it was elected to generate in-house expertise in the design and operation of ERH, together with the construction of a portable ERH/SVE system that could be deployed at multiple locations around the site. This paper describes the waste unit characteristics, the ERH system design and operation, together with extensive data accumulated from the first deployment adjacent to the C-Reactor building. The installation heated the vadose zone down to 62 feet bgs over a 60 day period during the summer of 2006 and raised soil temperatures to over 200 F. A total of 730 lbs of trichloroethylene (TCE) were removed over this period, and subsequent sampling indicated a removal efficiency of 99.4%

Assessment of different mechanisms of C-14 production in irradiated graphite of RBMK-1500 reactors

International Nuclear Information System (INIS)

Narkunas, Ernestas; Smaizys, Arturas; Poskas, Povilas; Kilda, Raimondas

2010-01-01

Two RBMK-1500 water-cooled graphite-moderated channel-type power reactors at the Ignalina Nuclear Power Plant (INPP) are under decommissioning now. The total mass of irradiated graphite in the cores of both units is more than 3600 tons. The main source of uncertainty in the numerical assessment of graphite activity is the uncertainty of the initial impurities content in graphite. Nitrogen is one of the most important impurities, having a large neutron capture cross-section. This impurity may become the dominant source of C-14 production. RBMK reactors graphite stacks operate in the cooling mixture of helium-nitrogen gases and this may additionally increase the quantity of the nitrogen impurity. In this paper the results of the numerical modelling of graphite activation for the INPP Unit I reactor are presented. In order to evaluate the C-14 activity dependence on the nitrogen impurity content, several cases with different nitrogen content were modelled taking into account initial nitrogen impurity quantities in the graphite matrix and possible nitrogen quantities entrapped in the graphite pores from cooling gases. (orig.)

Preliminary conceptual design for electrical and I and C system of a new research reactor

International Nuclear Information System (INIS)

Jung, Hoan Sung; Kim, Y. K.; Kim, M. J.; Kim, H. K.; Ryu, J. S.

2004-01-01

The core type and the process system design will be varied according to the reactor's application and capacity. A New research reactor is being designed by KAERI since 2002 and the process systems are not fixed yet. But control and instrument systems are similar to each other even though the application and the size are not same. So the C and I system that encompasses reactor protection system, reactor control system, and computer system was designed conceptually according to the requirements based on new digital technology and HANARO's proven design. The plant electrical system consists of off-site system that delivers bulk electrical power to the reactor site and on-site system that distributes and controls electrical power at the facility. The electrical system includes building service system that consist of lighting, communication, fire detection, grounding, cathodic protection, etc. also. This report describes the design requirements of on-site and off-site electric power system that set up from the codes and standards and the conceptual design based on the design requirements

Evaluation of Tehran research reactor (TRR) control rod worth using MCNP4C computer code

International Nuclear Information System (INIS)

Hosseini, Mohammad; Vosoughi, Naser; Hosseini, Seyed Abolfazl

2010-01-01

The main objective of reactor control system is to provide a safe reactor starting up, operation and shutting down. Calculation or measurement of precise values of control rod worth is of great importance in Tehran Research Reactor (TRR), considering the fact that they are the only controlling tools in the reactor. In present paper, simulation of TRR in First Operation Cycle (FOC) and in cold and clean core for the calculation of total and integral worth of control nods is reported. MCNP4C computer code has been used for all simulation process. Two method have been used for control rods worth calculation in this paper, namely the direct approach and perturbation method. It is shown that while the direct approach is appropriate for worth calculation of both the shim and the regulating control rods, the perturbation method is just suitable for tiny reactivity changes, i.e. for small initial part of regulating rods. Results of simulation are compared with the reported data in Safety Analysis Report (SAR) of Tehran research reactor and showed satisfactory agreement. (author)

Analysis on Configuration of I and C Systems for an Advanced HANARO Reactors

International Nuclear Information System (INIS)

Park, Gee Yong; Jung, H. S.; Ryu, J. S.; Park, C.

2006-01-01

In an advanced HANARO reactor (AHR), the instrumentation and control (I and C) systems are designed based on the digital system rather than the analog system installed in an existing HANARO instrumentation and control systems. While the safety and functionality of analog-based instrumentation and control system are experienced over a long period of operating time and also well-validated, the obsolescence and the lack of flexibility of this system have to move from the analog technology to the digital technology in the instrumentation and control systems to be used in nuclear power plants as well as nuclear research reactors. For establishing the adequate structure of instrumentation and control systems for an AHR, various instrumentation and control architectures are analyzed for their merits and demerits for use in I and C systems of an AHR and the most promising instrumentation and control architecture for an AHR are drawn from this analysis. The conceptual configuration of a digital-based safety shutdown system is proposed in this report

Nanocrystalline SiC and Ti₃SiC₂ Alloys for Reactor Materials: Annual Report

Energy Technology Data Exchange (ETDEWEB)

Henager, Charles H. [pnnl; Alvine, Kyle J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Roosendaal, Timothy J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shin, Yongsoon [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Nguyen, Ba Nghiep; Borlaug, Brennan A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jiang, Weilin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Arreguin, Shelly A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-01-15

A new dual-phase nanocomposite of Ti₃SiC₂/SiC is being synthesized using preceramic polymers, ceramic powders, and carbon nanotubes (CNTs) designed to be suitable for advanced nuclear reactors and perhaps as fuel cladding. The material is being designed to have superior fracture toughness compared to SiC, adequate thermal conductivity, and higher density than SiC/SiC composites. This annual report summarizes the progress towards this goal and reports progress in understanding certain aspects of the material behavior but some shortcomings in achieving full density or in achieving adequate incorporation of CNTs. The measured thermal conductivity is adequate and falls into an expected range based on SiC and Ti₃SiC₂. Part of this study makes an initial assessment for Ti₃SiC₂ as a barrier to fission product transport. Ion implantation was used to introduce fission product surrogates (Ag and Cs) and a noble metal (Au) in Ti₃SiC₂, SiC, and a synthesized at PNNL. The experimental results indicate that the implanted Ag in SiC is immobile up to the highest temperature (1273 K) applied in this study; in contrast, significant out-diffusion of both Ag and Au in MAX phase Ti₃SiC₂ occurs during ion implantation at 873 K. Cs in Ti₃SiC₂ is found to diffuse during post-irradiation annealing at 973 K, and noticeable Cs release from the sample is observed. This study may suggest caution in using Ti₃SiC₂ as a fuel cladding material for advanced nuclear reactors operating at very high temperatures. Progress is reported in thermal conductivity modeling of SiC-based materials that is relevant to this research, as is progress in modeling the effects of CNTs on fracture strength of SiC-based materials.

Evaluation of I and C architecture alternatives required for the jupiter Icy moons orbiter (JIMO) reactor

International Nuclear Information System (INIS)

Muhlheim, M. D.; Wood, R. T.; Bryan, W. L.; Wilson Jr, T. L.; Holcomb, D. E.; Korsah, K.; Jagadish, U.

2006-01-01

This paper discusses alternative architectural considerations for instrumentation and control (I and C) systems in high-reliability applications to support remote, autonomous, inaccessible nuclear reactors, such as a space nuclear power plant (SNPP) for mission electrical power and space exploration propulsion. This work supported the pre-conceptual design of the reactor control system for the Jupiter Icy Moons Orbiter (JIMO) mission. Long-term continuous operation without intermediate maintenance cycles forces consideration of alternatives to commonly used active, N-multiple redundancy techniques for high-availability systems. Long space missions, where mission duration can exceed the 50% reliability limit of constituent components, can make active, N-multiple redundant systems less reliable than simplex systems. To extend a control system lifetime beyond the 50% reliability limits requires incorporation of passive redundancy of functions. Time-dependent availability requirements must be factored into the use of combinations of active and passive redundancy techniques for different mission phases. Over the course of a 12 to 20-year mission, reactor control, power conversion, and thermal management system components may fail, and the I and C system must react and adjust to accommodate these failures and protect non-failed components to continue the mission. This requires architectural considerations to accommodate partial system failures and to adapt to multiple control schemes according to the state of non-failed components without going through a complete shutdown and restart cycle. Relevant SNPP I and C architecture examples provide insights into real-time fault tolerance and long-term reliability and availability beyond time periods normally associated with terrestrial power reactor I and C systems operating cycles. I and C architectures from aerospace systems provide examples of highly reliable and available control systems associated with short- and long

Application of the master curve approach to fracture mechanics characterisation of reactor pressure vessel steel

International Nuclear Information System (INIS)

Viehrig, Hans-Werner; Zurbuchen, Conrad; Kalkhof, Dietmar

2010-06-01

The paper presents results of a research project founded by the Swiss Federal Nuclear Inspectorate concerning the application of the Master Curve approach in nuclear reactor pressure vessels integrity assessment. The main focus is put on the applicability of pre-cracked 0.4T-SE(B) specimens with short cracks, the verification of transferability of MC reference temperatures T 0 from 0.4T thick specimens to larger specimens, ascertaining the influence of the specimen type and the test temperature on T 0 , investigation of the applicability of specimens with electroerosive notches for the fracture toughness testing, and the quantification of the loading rate and specimen type on T 0 . The test material is a forged ring of steel 22 NiMoCr 3-7 of the uncommissioned German pressurized water reactor Biblis C. SE(B) specimens with different overall sizes (specimen thickness B=0.4T, 0.8T, 1.6T, 3T, fatigue pre-cracked to a/W=0.5 and 20% side-grooved) have comparable T 0 . T 0 varies within the 1σ scatter band. The testing of C(T) specimens results in higher T 0 compared to SE(B) specimens. It can be stated that except for the lowest test temperature allowed by ASTM E1921-09a, the T 0 values evaluated with specimens tested at different test temperatures are consistent. The testing in the temperature range of T 0 ± 20 K is recommended because it gave the highest accuracy. Specimens with a/W=0.3 and a/W=0.5 crack length ratios yield comparable T 0 . The T 0 of EDM notched specimens lie 41 K up to 54 K below the T 0 of fatigue pre-cracked specimens. A significant influence of the loading rate on the MC T 0 was observed. The HSK AN 425 test procedure is a suitable method to evaluate dynamic MC tests. The reference temperature T 0 is eligible to define a reference temperature RT To for the ASME-KIC reference curve as recommended in the ASME Code Case N-629. An additional margin has to be defined for the specific type of transient to be considered in the RPV integrity assessment

Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.

2000-02-11

A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area.

Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

International Nuclear Information System (INIS)

Flach, G.P.

2000-01-01

A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area

Development of SiC Neutron Detector Assembly to Measure the Neutron Flux of the Reactor Core

Energy Technology Data Exchange (ETDEWEB)

Park, Se Hwan; Park, June Sic; Shin, Hee Sung; Kim, Ho Dong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Yong Kyun [Hanyang University, Seoul (Korea, Republic of)

2012-05-15

At present, the conventional detector to measure the neutron at harsh environment is a Self Powered Neutron Detector (SPND). Rhodium(Rh)-103 is in the SPND. When neutron is incident on the Rhodium, the neutron capture reaction occurs, and the Rh-103 is converted to Rh-104. The Rh-104 is decayed to Pd-104 by {beta}-decay, and electrons are generated as the decay products. Because of the half life of Rh-104, approximately 5 minutes are required for the SPND output to reach the equilibrium condition. Therefore the on-line monitoring of the nuclear reactor state is limited if the neutron flux in the reactor core is monitored with the SPND. Silicon carbide (SiC) has the possibility to be developed as neutron detector at harsh environment, because the SiC can be operative at high temperature and high neutron flux conditions. Previously, the basic operation properties of the SiC detector were studied. Also, the radiation response of the SiC detector was studied at high neutron and gamma dose rate. The measurement results for an ex-core neutron flux monitor or a neutron flux monitor of the spent fuel were published. The SiC detector was also developed as neutron detector to measure the fissile material with active interrogation method. However, the studies about the development of SiC detector are still limited. In the present work, the radiation damage effect of the SiC detector was studied. The detector structure was determined based on the study, and a neutron detector assembly was made with the SiC detectors. The neutron and gamma-ray response of the detector assembly is presented in this paper. The detector assembly was positioned in the HANARO research reactor core, the performance test was done. The preliminary results are also included in this paper

A study on the sealing performance of metallic C-rings in reactor pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Jia, Xiaohong, E-mail: jiaxh@mail.tsinghua.edu.cn [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Chen, Huaming [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Li, Xinggen [Ningbo Tiansheng Sealing Packing Co., Ltd, Ningbo 315302 (China); Wang, Yuming [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Wang, Longke [Eaton Corporation, MN (United States)

2014-10-15

Highlights: • FE analysis on compression–resilience of metallic C-ring is performed and validated by experiments. • Model of RPV sealing system including the C-rings is developed. • Deformation data from factory hydraulic test of the RPV are used to verify the model. • C-rings’ behavior under designing condition is analyzed. • The model provides a reliable evaluation on the sealing performance of RPV. - Abstract: Double metallic C-rings are used in pressure vessel of pressurized water reactor (PWR) to seal the bolt-connected flanges. To evaluate the sealing performance, it is necessary to study both the C-rings’ intrinsic properties and their behavior in reactor pressure vessel (RPV) under various loading conditions. The compression–resilience property and linear load are the basic information to evaluate the performance of a well-designed C-ring's. An equivalent model of C-ring is constructed by means of ANSYS to analyze its intrinsic properties, and is also validated by experiments on scaled samples. This model is applied to develop a 2D-axisymmetric FE model of sealing system including RPV and C-rings with the consideration of nonlinear material, contacting problem and multiple coupled effects. The simulation results of RPV deformation under the hydraulic test condition agree well with the data of factory hydraulic test. With the verified model, an analysis under the designing condition is performed to study C-rings’ behavior in the RPV, and then provides a reliable evaluation on the sealing performance of RPV.

Supercritical Water Reactors

International Nuclear Information System (INIS)

Bouchter, J.C.; Dufour, P.; Guidez, J.; Latge, C.; Renault, C.; Rimpault, G.

2014-01-01

The supercritical water reactor (SCWR) is one of the 6 concepts selected for the 4. generation of nuclear reactors. SCWR is a new concept, it is an attempt to optimize boiling water reactors by using the main advantages of supercritical water: only liquid phase and a high calorific capacity. The SCWR requires very high temperatures (over 375 C degrees) and very high pressures (over 22.1 MPa) to operate which allows a high conversion yield (44% instead of 33% for a PWR). Low volumes of coolant are necessary which makes the neutron spectrum shift towards higher energies and it is then possible to consider fast reactors operating with supercritical water. The main drawbacks of supercritical water is the necessity to use very high pressures which has important constraints on the reactor design, its physical properties (density, calorific capacity) that vary strongly with temperatures and pressures and its very high corrosiveness. The feasibility of the concept is not yet assured in terms of adequate materials that resist to corrosion, reactor stability, reactor safety, and reactor behaviour in accidental situations. (A.C.)

A simulation of a pebble bed reactor core by the MCNP-4C computer code

Directory of Open Access Journals (Sweden)

Bakhshayesh Moshkbar Khalil

2009-01-01

Full Text Available Lack of energy is a major crisis of our century; the irregular increase of fossil fuel costs has forced us to search for novel, cheaper, and safer sources of energy. Pebble bed reactors - an advanced new generation of reactors with specific advantages in safety and cost - might turn out to be the desired candidate for the role. The calculation of the critical height of a pebble bed reactor at room temperature, while using the MCNP-4C computer code, is the main goal of this paper. In order to reduce the MCNP computing time compared to the previously proposed schemes, we have devised a new simulation scheme. Different arrangements of kernels in fuel pebble simulations were investigated and the best arrangement to decrease the MCNP execution time (while keeping the accuracy of the results, chosen. The neutron flux distribution and control rods worth, as well as their shadowing effects, have also been considered in this paper. All calculations done for the HTR-10 reactor core are in good agreement with experimental results.

Objectives and present status of the German risk evaluation study

International Nuclear Information System (INIS)

Birkhofer, A.; Koeberlein, K.; Heuser, F.W.

1977-01-01

For the German risk evaluation study, analogous to the Rasmussen report (WASH--1400), embarked upon in June 1976, the Kernkraftwerk Biblis B serves as the plant of reference. The first interim results are available for various sub-headings of the study. The main finding seems to be the decisive importance of the containment in limiting the accident consequences even in those cases where, on account of postulated failure of safety systems, the melt down of the reactor core is to be expected. (orig./HP) [de

The assessment of voce coefficient for WWR-c reactor

International Nuclear Information System (INIS)

Kochnov, O.Yu.; Rybkin, N.I.

2006-01-01

The air cavity effect in WWR-ts reactor core on the total reactivity is analyzed. The experimental data of void coefficient depending on the air cavity position inside the reactor core are obtained [ru

Methanogenesis in Thermophilic Biogas Reactors

DEFF Research Database (Denmark)

Ahring, Birgitte Kiær

1995-01-01

Methanogenesis in thermophilic biogas reactors fed with different wastes is examined. The specific methanogenic activity with acetate or hydrogen as substrate reflected the organic loading of the specific reactor examined. Increasing the loading of thermophilic reactors stabilized the process as ....... Experiments using biogas reactors fed with cow manure showed that the same biogas yield found at 550 C could be obtained at 610 C after a long adaptation period. However, propionate degradation was inhibited by increasing the temperature.......Methanogenesis in thermophilic biogas reactors fed with different wastes is examined. The specific methanogenic activity with acetate or hydrogen as substrate reflected the organic loading of the specific reactor examined. Increasing the loading of thermophilic reactors stabilized the process...... as indicated by a lower concentration of volatile fatty acids in the effluent from the reactors. The specific methanogenic activity in a thermophilic pilot-plant biogas reactor fed with a mixture of cow and pig manure reflected the stability of the reactor. The numbers of methanogens counted by the most...

Materials surveillance program for C-E NSSS reactor vessels

International Nuclear Information System (INIS)

Koziol, J.J.

1977-01-01

Irradiation surveillance programs for light water NSSS reactor vessels provide the means by which the utility can assess the extent of neutron-induced changes in the reactor vessel materials. These programs are conducted to verify, by direct measurement, the conservatism in the predicted radiation-induced changes and hence the operational parameters (i.e., heat-up, cooldown, and pressurization rates). In addition, such programs provide assurance that the scheduled adjustments in the operational parameters are made with ample margin for safe operation of the plant. During the past 3 years, several documents have been promulgated establishing the criteria for determining both the initial properties of the reactor vessel materials as well as measurement of changes in these initial properties as a result of irradiation. These documents, ASTM E-185-73, ''Recommended Practice for Surveillance Tests for Nuclear Reactor Vessels,'' and Appendix H to 10 CFR 50, ''Reactor Vessel Material Surveillance Program Requirements,'' are complementary to each other. They are the result of a change in the basic philosophy regarding the design and analysis of reactor vessels. In effect, the empirical ''transition temperature approach,'' which was used for design, was replaced by the ''analytical fracture mechanics approach.'' The implementation of this technique was described in Welding Research Council Bulletin 1975 and Appendix G to ASME Code Section III. Further definition of requirements appears in Appendix G to 10 CFR 50 published in July 1973. It is the intent of this paper to describe (1) a typical materials surveillance program for the reactor vessel of a Combustion Engineering NSSS, and (2) how the results of such programs, as well as experimental programs provide feed-back for improvement of materials to enhance their radiation resistance and thereby further improve the safety and reliability of future plants. (author)

Canada-India Reactor (CIR)

Energy Technology Data Exchange (ETDEWEB)

None

1960-12-15

Design information on the Canada-India Reactor is presented. Data are given on reactor physics, the core, fuel elements, core heat transfer, control, reactor vessel, fluid flow, reflector and shielding, containment, cost estimates, and research facilities. Drawings of vertical and horizontal sections of the reactor and fluid flow are included. (M.C.G.)

I and C safety research at the OECD Halden reactor project

International Nuclear Information System (INIS)

Gran, B.A.

2007-01-01

The overall objective of the Halden Reactor Project research on software systems dependability is to contribute to the successful introduction of digital I and C systems into NPPs. When celebrating the 50 years of the Halden Project in 2008, about 100 written reports have been delivered within this research. This research covers a number of topics covering safety, reliability, validation and verification, quality assurance, risk assessment, requirement engineering, error propagation, qualitative and quantitative assessment. In the paper some activities are described, pinpointing the importance of good joint projects with organisations in the member countries

Conceptual design of nuclear fusion power reactor DREAM. Reactor structures and remote maintenance

International Nuclear Information System (INIS)

Nishio, Satoshi; Seki, Yasushi; Ueda, Shuzo; Kurihara, Ryoichi; Adachi, Junichi; Yamazaki, Seiichiro; Hashimoto, Toshiyuki.

1997-01-01

Nuclear fusion reactors are required to be able to compete another energy sources in economy, reliability, safety and environmental integrity for commercial use. In the DREAM (DRastically EAsy Maintenance) reactor, a very low activated material of SiC/SiC composite has been introduced for the structural material, a reactor configuration for very easy maintenance and the helium gas of a high temperature for the cooling system, and hence DREAM has been proven to be very attractively as the commercial power reactor due to the high availability and efficiency of the plant and minimization of radioactive wastes. (author)

Reactor as furnace and reactor as lamp

International Nuclear Information System (INIS)

Goldanskii, V.I.

1992-01-01

There are presented general characteristics of the following ways of transforming of nuclear energy released in reactors into chemical : ordinary way (i.e. trough the heat, mechanical energy and electricity); chemonuclear synthesis ; use of high-temperature fuel elements (reactor as furnace); use of the mixed nγ-radiation of reactors; use of the radiation loops; radiation - photochemical synthesis (reactor as lamp). Advantage and disadvantages of all above variants are compared. The yield of the primary product of fixation of nitrogen (nitric oxide NO) in reactor with the high-temperature (above ca. 1900degC) fuel elements (reactor-furnace) can exceed W ∼ 200 kg per gram of burned uranium. For the latter variant (reactor-lamp) the yield of chemical products can reach W ∼ 60 kg. per gram of uranium. Such values of W are close to or even strongly exceed the yields of chemical products for other abovementioned variants and - what is particularly important - are not connected to the necessity of archscrupulous removal of radioactive contamination of products. (author)

Engineering Porous Polymer Hollow Fiber Microfluidic Reactors for Sustainable C-H Functionalization.

Science.gov (United States)

He, Yingxin; Rezaei, Fateme; Kapila, Shubhender; Rownaghi, Ali A

2017-05-17

Highly hydrophilic and solvent-stable porous polyamide-imide (PAI) hollow fibers were created by cross-linking of bare PAI hollow fibers with 3-aminopropyl trimethoxysilane (APS). The APS-grafted PAI hollow fibers were then functionalized with salicylic aldehyde for binding catalytically active Pd(II) ions through a covalent postmodification method. The catalytic activity of the composite hollow fiber microfluidic reactors (Pd(II) immobilized APS-grafted PAI hollow fibers) was tested via heterogeneous Heck coupling reaction of aryl halides under both batch and continuous-flow reactions in polar aprotic solvents at high temperature (120 °C) and low operating pressure. X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma (ICP) analyses of the starting and recycled composite hollow fibers indicated that the fibers contain very similar loadings of Pd(II), implying no degree of catalyst leaching from the hollow fibers during reaction. The composite hollow fiber microfluidic reactors showed long-term stability and strong control over the leaching of Pd species.

Reactor noise analysis applications in NPP I and C systems

Energy Technology Data Exchange (ETDEWEB)

Gloeckler, O. [International Atomic Energy Agency, Wagramer Strosse 5, A-1400 Vienna, Austria Ontario Power Generation, 230 Westney Road South, Ajax, Ont. L1S 7R3 (Canada)

2006-07-01

Reactor noise analysis techniques are used in many NPPs on a routine basis as 'inspection tools' to get information on the dynamics of reactor processes and their instrumentation in a passive, non-intrusive way. The paper discusses some of the tasks and requirements an NPP has to take to implement and to use the full advantages of reactor noise analysis techniques. Typical signal noise analysis applications developed for the monitoring of the reactor shutdown system and control system instrumentation of the Candu units of Ontario Power Generation and Bruce Power are also presented. (authors)

Identification of tertiary butyl alcohol (TBA)-utilizing organisms in BioGAC reactors using 13C-DNA stable isotope probing.

Science.gov (United States)

Aslett, Denise; Haas, Joseph; Hyman, Michael

2011-09-01

Biodegradation of the gasoline oxygenates methyl tertiary-butyl ether (MTBE) and ethyl tertiary-butyl ether (ETBE) can cause tertiary butyl alcohol (TBA) to accumulate in gasoline-impacted environments. One remediation option for TBA-contaminated groundwater involves oxygenated granulated activated carbon (GAC) reactors that have been self-inoculated by indigenous TBA-degrading microorganisms in ground water extracted from contaminated aquifers. Identification of these organisms is important for understanding the range of TBA-metabolizing organisms in nature and for determining whether self-inoculation of similar reactors is likely to occur at other sites. In this study (13)C-DNA-stable isotope probing (SIP) was used to identify TBA-utilizing organisms in samples of self-inoculated BioGAC reactors operated at sites in New York and California. Based on 16S rRNA nucleotide sequences, all TBA-utilizing organisms identified were members of the Burkholderiales order of the β-proteobacteria. Organisms similar to Cupriavidus and Methylibium were observed in both reactor samples while organisms similar to Polaromonas and Rhodoferax were unique to the reactor sample from New York. Organisms similar to Hydrogenophaga and Paucibacter strains were only detected in the reactor sample from California. We also analyzed our samples for the presence of several genes previously implicated in TBA oxidation by pure cultures of bacteria. Genes Mpe_B0532, B0541, B0555, and B0561 were all detected in (13)C-metagenomic DNA from both reactors and deduced amino acid sequences suggested these genes all encode highly conserved enzymes. One gene (Mpe_B0555) encodes a putative phthalate dioxygenase-like enzyme that may be particularly appropriate for determining the potential for TBA oxidation in contaminated environmental samples.

Application of macro-cellular SiC reactor to diesel engine-like injection and combustion conditions

Science.gov (United States)

Cypris, Weclas, M.; Greil, P.; Schlier, L. M.; Travitzky, N.; Zhang, W.

2012-05-01

One of novel combustion technologies for low emissions and highly efficient internal combustion engines is combustion in porous reactors (PM). The heat release process inside combustion reactor is homogeneous and flameless resulting in a nearly zero emissions level. Such combustion process, however is non-stationary, is performed under high pressure with requirement of mixture formation directly inside the combustion reactor (high pressure fuel injection). Reactor heat capacity resulting in lowering of combustion temperature as well as internal heat recuperation during the engine cycle changes the thermodynamic conditions of the process as compared to conventional engine. For the present investigations a macro-cellular lattice structure based on silicon carbide (non-foam structure) with 600 vertical cylindrical struts was fabricated and applied to engine-like combustion conditions (combustion chamber). The lattice design with a high porosity > 80% was shaped by indirect three-dimensional printing of a SiC powder mixed with a dextrin binder which also serves as a carbon precursor. In order to perform detailed investigations on low-and high-temperature oxidation processes in porous reactors under engine-like conditions, a special combustion chamber has been built and equipped with a Diesel common-rail injection system. This system simulates the thermodynamic conditions at the time instance of injection onset (corresponding to the nearly TDC of compression in a real engine). Overall analysis of oxidation processes (for variable initial pressure, temperature and air excess ratio) for free Diesel spray combustion and for combustion in porous reactor allows selection of three regions representing different characteristics of the oxidation process represented by a single-step and multi-step reactions Another characteristic feature of investigated processes is reaction delay time. There are five characteristic regions to be selected according to the delay time (t) duration

Temperature increases from 55 to 75 C in a two-phase biogas reactor result in fundamental alterations within the bacterial and archaeal community structure

Energy Technology Data Exchange (ETDEWEB)

Rademacher, Antje [Leibniz-Institut fuer Agrartechnik Potsdam-Bornim e.V. (ATB), Potsdam (Germany). Abt. Bioverfahrenstechnik; Technische Univ. Berlin (Germany). Inst. fuer Technischen Umweltschutz; Nolte, Christine; Schoenberg, Mandy; Klocke, Michael [Leibniz-Institut fuer Agrartechnik Potsdam-Bornim e.V. (ATB), Potsdam (Germany). Abt. Bioverfahrenstechnik

2012-10-15

Agricultural biogas plants were operated in most cases below their optimal performance. An increase in the fermentation temperature and a spatial separation of hydrolysis/acetogenesis and methanogenesis are known strategies in improving and stabilizing biogas production. In this study, the dynamic variability of the bacterial and archaeal community was monitored within a two-phase leach bed biogas reactor supplied with rye silage and straw during a stepwise temperature increase from 55 to 75 C within the leach bed reactor (LBR), using TRFLP analyses. To identify the terminal restriction fragments that were obtained, bacterial and archaeal 16S rRNA gene libraries were constructed. Above 65 C, the bacterial community structure changed from being Clostridiales-dominated toward being dominated by members of the Bacteroidales, Clostridiales, and Thermotogales orders. Simultaneously, several changes occurred, including a decrease in the total cell count, degradation rate, and biogas yield along with alterations in the intermediate production. A bioaugmentation with compost at 70 C led to slight improvements in the reactor performance; these did not persist at 75 C. However, the archaeal community within the downstream anaerobic filter reactor (AF), operated constantly at 55 C, altered by the temperature increase in the LBR. At an LBR temperature of 55 C, members of the Methanobacteriales order were prevalent in the AF, whereas at higher LBR temperatures Methanosarcinales prevailed. Altogether, the best performance of this two-phase reactor was achieved at an LBR temperature of below 65 C, which indicates that this temperature range has a favorable effect on the microbial community responsible for the production of biogas. (orig.)

Irradiations under magnetic field. Measurement of resistivity sample irradiations between 100 and 500 deg C in a swimming-pool reactor

International Nuclear Information System (INIS)

Pauleve, J.; Marchand, A.; Blaise, A.

1964-01-01

An oven is described which enables the irradiation of small samples in the maximum neutron flux of a swimming-pool reactor of 15 MW (Siloe), at temperatures of between 100 and 500 deg.C defined to ± 0,5 deg.C, The oven is very simple from the technological point of view, and has a diameter of only 27 mm, This permits resistivity measurements to be carried out under irradiation in the reactor, or as another example, it enables irradiations in a magnetic field of 5000 oersteds, created by an immersed solenoid. (authors) [fr

Nuclear reactor

International Nuclear Information System (INIS)

Garabedian, G.

1988-01-01

A liquid reactor is described comprising: (a) a reactor vessel having a core; (b) one or more satellite tanks; (c) pump means in the satellite tank; (d) heat exchanger means in the satellite tank; (e) an upper liquid metal conduit extending between the reactor vessel and the satellite tank; (f) a lower liquid metal duct extending between the reactor vessel and satellite tanks the upper liquid metal conduit and the lower liquid metal duct being arranged to permit free circulation of liquid metal between the reactor vessel core and the satellite tank by convective flow of liquid metal; (g) a separate sealed common containment vessel around the reactor vessel, conduits and satellite tanks; (h) the satellite tank having space for a volume of liquid metal that is sufficient to dampen temperature transients resulting from abnormal operating conditions

Generation IV reactors: reactor concepts

International Nuclear Information System (INIS)

Cardonnier, J.L.; Dumaz, P.; Antoni, O.; Arnoux, P.; Bergeron, A.; Renault, C.; Rimpault, G.; Delpech, M.; Garnier, J.C.; Anzieu, P.; Francois, G.; Lecomte, M.

2003-01-01

Liquid metal reactor concept looks promising because of its hard neutron spectrum. Sodium reactors benefit a large feedback experience in Japan and in France. Lead reactors have serious assets concerning safety but they require a great effort in technological research to overcome the corrosion issue and they lack a leader country to develop this innovative technology. In molten salt reactor concept, salt is both the nuclear fuel and the coolant fluid. The high exit temperature of the primary salt (700 Celsius degrees) allows a high energy efficiency (44%). Furthermore molten salts have interesting specificities concerning the transmutation of actinides: they are almost insensitive to irradiation damage, some salts can dissolve large quantities of actinides and they are compatible with most reprocessing processes based on pyro-chemistry. Supercritical water reactor concept is based on operating temperature and pressure conditions that infers water to be beyond its critical point. In this range water gets some useful characteristics: - boiling crisis is no more possible because liquid and vapour phase can not coexist, - a high heat transfer coefficient due to the low thermal conductivity of supercritical water, and - a high global energy efficiency due to the high temperature of water. Gas-cooled fast reactors combining hard neutron spectrum and closed fuel cycle open the way to a high valorization of natural uranium while minimizing ultimate radioactive wastes and proliferation risks. Very high temperature gas-cooled reactor concept is developed in the prospect of producing hydrogen from no-fossil fuels in large scale. This use implies a reactor producing helium over 1000 Celsius degrees. (A.C.)

Nuclear reactor construction with bottom supported reactor vessel

International Nuclear Information System (INIS)

Sharbaugh, J.E.

1987-01-01

This patent describes an improved liquid metal nuclear reactor construction comprising: (a) a nuclear reactor core having a bottom platform support structure; (b) a reactor vessel for holding a large pool of low pressure liquid metal coolant and housing the core; (c) a containment structure surrounding the reactor vessel and having a sidewall spaced outwardly from the reactor vessel side wall and having a base mat spaced below the reactor vessel bottom end wall; (d) a central small diameter post anchored to the containment structure base mat and extending upwardly to the reactor vessel to axially fix the bottom end wall of the reactor vessel and provide a center column support for the lower end of the reactor core; (e) annular support structure disposed in the reactor vessel on the bottom end wall and extending about the lower end of the core; (f) structural support means disposed between the containment structure base mat and bottom end of the reactor vessel wall and cooperating for supporting the reactor vessel at its bottom end wall on the containment structure base mat to allow the reactor vessel to expand radially but substantially prevent any lateral motions that might be imposed by the occurrence of a seismic event; (g) a bed of insulating material disposed between the containment structure base mat and the bottom end wall of the reactor vessel and uniformly supporting the reactor vessel at its bottom end wall; freely expand radially from the central post as it heats up while providing continuous support thereof; (h) a deck supported upon the wall of the containment vessel above the top open end of the reactor vessel; and (i) extendible and retractable coupling means extending between the deck and the top open end of the reactor vessel and flexibly and sealably interconnecting the reactor vessel at its top end to the deck

High-temperature and breeder reactors - economic nuclear reactors of the future

International Nuclear Information System (INIS)

Djalilzadeh, A.M.

1977-01-01

The thesis begins with a review of the theory of nuclear fission and sections on the basic technology of nuclear reactors and the development of the first generation of gas-cooled reactors applied to electricity generation. It then deals in some detail with currently available and suggested types of high temperature reactor and with some related subsidiary issues such as the coupling of different reactor systems and various schemes for combining nuclear reactors with chemical processes (hydrogenation, hydrogen production, etc.), going on to discuss breeder reactors and their application. Further sections deal with questions of cost, comparison of nuclear with coal- and oil-fired stations, system analysis of reactor systems and the effect of nuclear generation on electricity supply. (C.J.O.G.)

Effect of temperature increase from 55 to 65 degrees C on performance and microbial population dynamics of an anaerobic reactor treating cattle manure

DEFF Research Database (Denmark)

Ahring, Birgitte Kiær; Ibrahim, Ashraf; Mladenovska, Zuzana

2001-01-01

C, a decreased activity was found For glucosc-, acetate- , butyrate- and formate-utilizers and no significant activity was measured with propionate. Only the hydrogen-consuming methanogens showed an enhanced activity at 65 degreesC. Numbers of cultivable methanogens, estimated by the most probable number (MPN......The effect of a temperature increase from 55 to 65 degreesC on process performance and microbial population dynamics were investigated in thermophilic, lab-scale, continuously stirred tank reactors. The reactors had a working volume of 3 l and were fed with cattle manure at an organic loading rate....../d at 55 degreesC. Simultaneously, Ibe level of total volatile fatty acids, VFA, increased from being below 0.3g/l to 1.8-2.4g acetate/l. The specific methanogenic activities (SMA) of biomass from the reactors were measured with acetate, propionate, butyrate, hydrogen, formate and glucose. At 65 degrees...

Greater-than-Class C low-level radioactive waste characterization. Appendix A-3: Basis for greater-than-Class C low-level radioactive waste light water reactor projections

International Nuclear Information System (INIS)

Mancini, A.; Tuite, P.; Tuite, K.; Woodberry, S.

1994-09-01

This study characterizes low-level radioactive waste types that may exceed Class C limits at light water reactors, estimates the amounts of waste generated, and estimates radionuclide content and distribution within the waste. Waste types that may exceed Class C limits include metal components that become activated during operations, process wastes such as cartridge filters and decontamination resins, and activated metals from decommissioning activities. Operating parameters and current management practices at operating plants are reviewed and used to estimate the amounts of low-level waste exceeding Class C limits that is generated per fuel cycle, including amounts of routinely generated activated metal components and process waste. Radionuclide content is calculated for specific activated metals components. Empirical data from actual low-level radioactive waste are used to estimate radionuclide content for process wastes. Volumes and activities are also estimated for decommissioning activated metals that exceed Class C limits. To estimate activation levels of decommissioning waste, six typical light water reactors are modeled and analyzed. This study does not consider concentration averaging

Maintenance and material aspects of DREAM reactor

International Nuclear Information System (INIS)

Ueda, S.; Nishio, S.; Yamada, R.; Seki, Y.; Kurihara, R.; Adachi, J.; Yamazaki, S.

2000-01-01

A concept of a commercial fusion power reactors (Fusion Power: 5.5 GW, electric output: 2.7 GW) having high environmental safety, high thermal efficiency and high availability has been studied in JAERI. The gross reactor configuration was designed to achieve good maintainability, high performance breeding blanket, high efficient power generation system and little radwastes. Design was based on the use of low activation structural material (SiC/SiC composites) and helium as a coolant. In this paper, maintenance and material aspects of DREAM reactor design is discussed. The concluding remarks are as follows. (1) The difficulty of development of maintenance tool is alleviated by sector replacement and the radiation dose environment less than 10 Gy/h in a reactor chamber. (2) Design requirement and present status of SiC/SiC composites was investigated. (3) The SiC/SiC composite development program is planned to satisfy the requirements of DREAM reactor

Homogeneous SLOWPOKE reactors for replacing SLOWPOKE-2 research reactors and the production of radioisotopes

International Nuclear Information System (INIS)

Bonin, H.W.; Hilborn, J.W.; Carlin, G.E.; Gagnon, R.; Busatta, P.

2014-01-01

Inspired from the inherently safe SLOWPOKE-2 research reactor, the Homogeneous SLOWPOKE reactor was conceived with a double goal: replacing the heterogeneous SLOWPOKE-2 reactors when they reach end-of-core life to continue their missions of neutron activation analysis and neutron radiography at universities, and to produce radioisotopes such as 99 Mo for medical applications. A homogeneous reactor core allows a much simpler extraction of radioisotopes (such as 99 Mo) for applications in industry and nuclear medicine. The 20 kW Homogeneous SLOWPOKE reactor was modelled using both the deterministic WIMS-AECL and the probabilistic MCNP 5 reactor simulation codes. The homogeneous fuel mixture was a dilute aqueous solution of Uranyl Sulfate (UO 2 SO 4 ) with 994.2 g of 235 U (enrichment at 20%) providing an excess reactivity at operating temperature (40 o C) of 3.8 mk for a molality determined as 1.46 mol kg -1 for a Zircaloy-2 reactor vessel. Because this reactor is intended to replace the core of SLOWPOKE-2 reactors, the Homogeneous SLOWPOKE reactor core had a height about twice its diameter. The reactor could be controlled by mechanical absorber rods in the beryllium reflector, chemical control in the core, or a combination of both. The safety of the Homogeneous SLOWPOKE reactor was analysed for both normal operation and transient conditions. Thermal-hydraulics calculations used COMSOL Multiphysics and the results showed that natural convection was sufficient to ensure adequate reactor cooling in all situations. The most severe transient simulated resulted from a 5.87 mk step positive reactivity insertion to the reactor in operation at critical and at steady state at 20 o C. Peak temperature and power were determined as 83 o C and 546 kW, respectively, reached 5.1 s after the reactivity insertion. However, the power fell rapidly to values below 20 kW some 35 s after the peak and remained below that value thereafter. Both the temperature and void coefficients are

Homogeneous SLOWPOKE reactors for replacing SLOWPOKE-2 research reactors and the production of radioisotopes

Energy Technology Data Exchange (ETDEWEB)

Bonin, H.W., E-mail: bonin-h@rmc.ca [Royal Military College of Canada, Kingston, Ontario (Canada); Hilborn, J.W. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Carlin, G.E. [Ontario Power Generation, Toronto, Ontario (Canada); Gagnon, R.; Busatta, P. [Canadian Forces (Canada)

2014-07-01

Inspired from the inherently safe SLOWPOKE-2 research reactor, the Homogeneous SLOWPOKE reactor was conceived with a double goal: replacing the heterogeneous SLOWPOKE-2 reactors when they reach end-of-core life to continue their missions of neutron activation analysis and neutron radiography at universities, and to produce radioisotopes such as {sup 99}Mo for medical applications. A homogeneous reactor core allows a much simpler extraction of radioisotopes (such as {sup 99}Mo) for applications in industry and nuclear medicine. The 20 kW Homogeneous SLOWPOKE reactor was modelled using both the deterministic WIMS-AECL and the probabilistic MCNP 5 reactor simulation codes. The homogeneous fuel mixture was a dilute aqueous solution of Uranyl Sulfate (UO{sub 2}SO{sub 4}) with 994.2 g of {sup 235}U (enrichment at 20%) providing an excess reactivity at operating temperature (40 {sup o}C) of 3.8 mk for a molality determined as 1.46 mol kg{sup -1} for a Zircaloy-2 reactor vessel. Because this reactor is intended to replace the core of SLOWPOKE-2 reactors, the Homogeneous SLOWPOKE reactor core had a height about twice its diameter. The reactor could be controlled by mechanical absorber rods in the beryllium reflector, chemical control in the core, or a combination of both. The safety of the Homogeneous SLOWPOKE reactor was analysed for both normal operation and transient conditions. Thermal-hydraulics calculations used COMSOL Multiphysics and the results showed that natural convection was sufficient to ensure adequate reactor cooling in all situations. The most severe transient simulated resulted from a 5.87 mk step positive reactivity insertion to the reactor in operation at critical and at steady state at 20 {sup o}C. Peak temperature and power were determined as 83 {sup o}C and 546 kW, respectively, reached 5.1 s after the reactivity insertion. However, the power fell rapidly to values below 20 kW some 35 s after the peak and remained below that value thereafter. Both the

Reactor safety: the Nova computer system

International Nuclear Information System (INIS)

Eisgruber, H.; Stadelmann, W.

1991-01-01

After instances of maloperation, the causes of defects, the effectiveness of the measures taken to control the situation, and possibilities to avoid future recurrences need to be investigated above all before the plant is restarted. The most important aspect in all these efforts is to check the sequence in time, and the completeness, of the control measures initiated automatically. For this verification, a computer system is used instead of time-consuming manual analytical techniques, which produces the necessary information almost in real time. The results are available within minutes after completion of the measures initiated automatically. As all short-term safety functions are initiated by automatic systems, their consistent and comprehensive verification results in a clearly higher level of safety. The report covers the development of the computer system, and its implementation, in the Gundremmingen nuclear power station. Similar plans are being pursued in Biblis and Muelheim-Kaerlich. (orig.) [de

Reactor for exothermic reactions

Science.gov (United States)

Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

1993-03-02

A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F. Wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

Reactor facility

International Nuclear Information System (INIS)

Suzuki, Hiroaki; Murase, Michio; Yokomizo, Osamu.

1997-01-01

The present invention provides a BWR type reactor facility capable of suppressing the amount of steams generated by the mutual effect of a failed reactor core and coolants upon occurrence of an imaginal accident, and not requiring spacial countermeasures for enhancing the pressure resistance of the container vessel. Namely, a means for supplying cooling water at a temperature not lower by 30degC than the saturated temperature corresponding to the inner pressure of the containing vessel upon occurrence of an accident is disposed to a lower dry well below the pressure vessel. As a result, upon occurrence of such an accident that the reactor core should be melted and flown downward of the pressure vessel, when cooling water at a temperature not lower than the saturated temperature, for example, cooling water at 100degC or higher is supplied to the lower dry well, abrupt generation of steams by the mutual effect of the failed reactor core and cooling water is scarcely caused compared with a case of supplying cooling water at a temperature lower than the saturation temperature by 30degC or more. Accordingly, the amount of steams to be generated can be suppressed, and special countermeasure is no more necessary for enhancing the pressure resistance of the container vessel is no more necessary. (I.S.)

Use of MCNP for characterization of reactor vessel internals waste from decommissioned nuclear reactors

International Nuclear Information System (INIS)

Love, E.F.; Pauley, K.A.; Reid, B.D.

1995-09-01

This study describes the use of the Monte Carlo Neutron-Photon (MCNP) code for determining activation levels of irradiated reactor vessel internals hardware. The purpose of the analysis is to produce data for the Department of Energy's Greater-Than-Class C Low-Level Radioactive Waste Program. An MCNP model was developed to analyze the Yankee Rowe reactor facility. The model incorporates reactor geometry, material compositions, and operating history data acquired from Yankee Atomic Electric Company. In addition to the base activation analysis, parametric studies were performed to determine the sensitivity of activation to specific parameters. A component sampling plan was also developed to validate the model results, although the plan was not implemented. The calculations for the Yankee Rowe reactor predict that only the core baffle and the core support plates will be activated to levels above the Class C limits. The parametric calculations show, however, that the large uncertainties in the material compositions could cause errors in the estimates that could also increase the estimated activation level of the core barrel to above the Class C limits. Extrapolation of the results to other reactor facilities indicates that in addition to the baffle and support plates, core barrels may also be activated to above Class C limits; however the classification will depend on the specific operating conditions of the reactor and the specific material compositions of the metal, as well as the use of allowable concentration averaging practices in packaging and classifying the waste

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure.

Science.gov (United States)

Nielsen, H B; Mladenovska, Z; Westermann, P; Ahring, B K

2004-05-05

A two-stage 68 degrees C/55 degrees C anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68 degrees C for periods of 36, 108, and 168 h, and subsequently digested at 55 degrees C. In a lab-scale experiment, the performance of a two-stage reactor system, consisting of a digester operating at 68 degrees C with a hydraulic retention time (HRT) of 3 days, connected to a 55 degrees C reactor with 12-day HRT, was compared with a conventional single-stage reactor running at 55 degrees C with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single-stage reactor. The 68 degrees C reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic/fermentative bacteria were significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. The density levels of methanogens utilizing H2/CO2 or formate were, however, in the same range for all reactors, although the degradation of these substrates was significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. Temporal temperature gradient electrophoresis profiles (TTGE) of the 68 degrees C reactor demonstrated a stable bacterial community along with a less divergent community of archaeal species. Copyright 2004 Wiley Periodicals, Inc.

Mirror fusion reactor design

International Nuclear Information System (INIS)

Neef, W.S. Jr.; Carlson, G.A.

1979-01-01

Recent conceptual reactor designs based on mirror confinement are described. Four components of mirror reactors for which materials considerations and structural mechanics analysis must play an important role in successful design are discussed. The reactor components are: (a) first-wall and thermal conversion blanket, (b) superconducting magnets and their force restraining structure, (c) neutral beam injectors, and (d) plasma direct energy converters

Study of the obtainment of Mo{sub 2}C by gas-solid reaction in a fixed and rotary bed reactor; Estudo da obtencao de Mo{sub 2}C por reacao gas-solido em reator de leito fixo e rotativo

Energy Technology Data Exchange (ETDEWEB)

Araujo, C.P.B. de; Souza, C.P. de; Souto, M.V.M.; Barbosa, C.M.; Frota, A.V.V.M., E-mail: cpbaraujo@gmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

Carbides' synthesis via gas-solid reaction overcomes many of the difficulties found in other processes, requiring lower temperatures and reaction times than traditional metallurgic routes, for example. In carbides' synthesis in fixed bed reactors (FB) the solid precursor is permeated by the reducing/carburizing gas stream forming a packed bed without mobility. The use of a rotary kiln reactor (RK) adds a mixing character to this process, changing its fluid-particle dynamics. In this work ammonium molybdate was subjected to carbo-reduction reaction (CH4 / H2) in both reactors under the same gas flow (15L / h) and temperature (660 ° C) for 180 minutes. Complete conversion was observed Mo2C (dp = 18.9nm modal particles sizes' distribution) in the fixed bed reactor. In the RK reactor this conversion was only partial (∼ 40%) and Mo2C and MoO3 (34nm dp = bimodal) could be observed on the produced XRD pattern. Partial conversion was attributed to the need to use higher solids loading in the reactor CR (50% higher) to avoid solids to centrifuge. (author)

A COMPARISON OF (PuU)C AND (PuU)O$sub 2$ FUELED FAST BREEDER REACTORS

Energy Technology Data Exchange (ETDEWEB)

Kazi, A. Halim; Rosen, Stanley

1963-11-15

BS>A conceptual evaluation is presented of a (PuU)C 500Mw(e) reactor which uses a moderate power generation of 40 kw/ft and a maximum fuel temperature of 2900 deg F, well below the 4500 deg F melting point of Pu/sub 0.2/U/sub 0.8/C. The principal design characteristics and fuel cycle costs are tabulated together with those of a (PuU)O/sub 2/ design of equal power. The comparison shows that the carbide core has significant economic and safety advantages over the oxide core. (D.L.C.)

Physical security at research reactors

International Nuclear Information System (INIS)

Clark, R.A.

1977-01-01

Of the 84 non-power research facilities licensed under 10 CFR Part 50, 73 are active (two test reactors, 68 research reactors and three critical facilities) and are required by 10 CFR Part 73.40 to provide physical protection against theft of SNM and against industrial sabotage. Each licensee has developed a security plan required by 10 CFR Part 50.34(c) to demonstrate the means of compliance with the applicable requirements of 10 CFR Part 73. In 1974, the Commission provided interim guidance for the organization and content of security plans for (a) test reactors, (b) medium power research and training reactors, and (c) low power research and training reactors. Eleven TRIGA reactors, with power levels greater than 250 kW and all other research and training reactors with power levels greater than 100 kW and less than or equal to 5,000 kW are designated as medium power research and training reactors. Thirteen TRIGA reactors with authorized power levels less than 250 kW are considered to be low power research and training reactors. Additional guidance for complying with the requirements of 73.50 and 73.60, if applicable, is provided in the Commission's Regulatory Guides. The Commission's Office of Inspection and Enforcement inspects each licensed facility to assure that an approved security plan is properly implemented with appropriate procedures and physical protection systems

Comparative assessment of instrumentation and control (I and C) system architectures for research reactors

International Nuclear Information System (INIS)

Khalil, Rah Man; Heo, Gyun Young; Son, Han Seong; Kim, Young Ki; Park, Jae Kwan

2012-01-01

Application of digital I and C has increased in nuclear industry since last two decades but lack of experience, innovative and naive nature of technology and insufficient failure information raised questions on its use. The issues has been highlighted due to the use of digital I and C which were not relevant to analog. These are the potential weakness of digital systems for Common Cause Failure, threat to system security and reliability due to inter channel communication, need for highly integrated control room and difficulty to assess the digital I and C reliability. In the existing scenario, HANARO and JRTR have hybrid I and C systems (digital plus analog) whereas OPAL is fully digitalized. In order to authenticate the choice of fully digital I and C architecture for research reactor, it is required to perform assessment from risk point of view, cyber security as well other issues. The architecture assessment method and restrictions are discussed in the next part of article

Joining of SiC/SiCf ceramic matrix composites for fusion reactor blanket applications

International Nuclear Information System (INIS)

Colombo, P.; Riccardi, B.; Donato, A.; Scarinci, G.

2000-01-01

Using a preceramic polymer, joints between SiC/SiC f ceramic matrix composites were obtained. The polymer, upon pyrolysis at high temperature, transforms into a ceramic material and develops an adhesive bonding with the composite. The surface morphology of 2D and 3D SiC/SiC f composites did not allow satisfactory results to be obtained by a simple application of the method initially developed for monolithic SiC bodies, which employed the use of a pure silicone resin. Thus, active or inert fillers were mixed with the preceramic polymer, in order to reduce its volumetric shrinkage which occurs during pyrolysis. In particular, the joints realized using the silicone resin with Al-Si powder as reactive additive displayed remarkable shear strength (31.6 MPa maximum). Large standard deviation for the shear strength has nevertheless been measured. The proposed joining method is promising for the realization of fusion reactor blanket structures, even if presently the measured strength values are not fully satisfactory

Comparative assessment of instrumentation and control (I and C) system architectures for research reactors

Energy Technology Data Exchange (ETDEWEB)

Khalil, Rah Man; Heo, Gyun Young [Kyung Hee Univ., Seoul (Korea, Republic of); Son, Han Seong [Joongbu Univ., Chungnam (Korea, Republic of); Kim, Young Ki; Park, Jae Kwan [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Application of digital I and C has increased in nuclear industry since last two decades but lack of experience, innovative and naive nature of technology and insufficient failure information raised questions on its use. The issues has been highlighted due to the use of digital I and C which were not relevant to analog. These are the potential weakness of digital systems for Common Cause Failure, threat to system security and reliability due to inter channel communication, need for highly integrated control room and difficulty to assess the digital I and C reliability. In the existing scenario, HANARO and JRTR have hybrid I and C systems (digital plus analog) whereas OPAL is fully digitalized. In order to authenticate the choice of fully digital I and C architecture for research reactor, it is required to perform assessment from risk point of view, cyber security as well other issues. The architecture assessment method and restrictions are discussed in the next part of article.

Nuclear power plant remote monitoring system of Hessen (KFUe Hessen) now fully available

International Nuclear Information System (INIS)

Lettmann, W.; Merkel, M.

1991-01-01

The remote monitoring system for the Biblis nuclear power station has commenced operation in 1990. It is intended to provide the radiological data and other information required by the supervisory Land authority for performing its supervisory functions in accordance with the Atomic Energy Act. The monitoring station records and reports emissions of the reactor station during specified normal operation and as a result of incidents or accidents, measures local dose rates at four measuring stations at the power plant fence, and records the meteorological conditions. The system is explained in detail, including illustration and graphs. (BBR) [de

Expected characteristics of future reactors for human beings

International Nuclear Information System (INIS)

Taketani, Kiyoaki

1992-01-01

Based on four reactor safety components (namely: a) God-given safety, b) Equipment safety, c) Quick-response safety, d) Containing safety), categorical assessment is made of various nuclear reactor concepts ranging from present existing reactors to future reactors based on innovative reactor design. In pursuit of nuclear reactor safety, ultimate characteristics of the ideal nuclear reactor are expected to coincide with those of an inherently safe reactor. A definition of 'inherently safe' has already been proposed by a committee in Japan. As a realistic and existable reactor, which is as close to the ideal reactor, a future reactor which is almost the same as a global reactor, is proposed. This global reactor must be constructable anywhere on earth and must permit easy operation and maintenance by anyone. It is also discussed to identify what behavior is expected of the global reactor under various conditions. At the same time, this future reactor which includes the global reactor, should solve a) the nuclear fuel resource issue, b) efficient utilization of fission energy and c) environmental issues as the greenhouse effect. (author). 7 refs., 2 figs

Temperature etalon of WWER-440 reactor

International Nuclear Information System (INIS)

Stanc, S.; Slanina, M.

2001-01-01

The presentation deals with the description, parameters and advantages of use of the temperature etalon. The system ensures temperature measurement of reactor outlet and inlet temperatures with high accuracy. Accuracy of temperature measurement is 0.18 deg C, accuracy of temperature difference measurement is 0.14 deg C, both with probability 0.95. Using the temperature etalon it is possible to increase accuracy of the standard temperature reactor measurements and to check their accuracy in the course of power reactor statuses in every measurement cycle. Temperature reactor etalon was installed in 12 WWER-440 units in Slovakia, Bohemia and Bulgaria. (Authors)

Resolution of the Task A-11 reactor-vessel materials-toughness safety issue. Appendices C-K

International Nuclear Information System (INIS)

1982-10-01

The central problem in the unresolved safety issue A-11, Reactor Vessel Materials Toughness, was to provide guidance in performing analyses required by 10 CFR Part 50, Appendix G, Section V.C. for reactor pressure vessels (RPVs) which fail to meet the toughness requirement during service life as a result of neutron radiation embrittlement. Although the methods of linear-elastic fracture mechanics (LEFM) were adequate for low-temperature RPV problems, they were inapplicable under operating conditions because vessel steels, even those which exhibit less than 50 ft-lb of C/sub v/ energy, were relatively tough at temperatures where the impact energy reached its upper shelf values. A technical team of recognized experts was organized to assist the NRC staff in addressing the problem. Using the foundation of the tearing modulus concept, which had been developed under earlier NRC sponsorship, relationships were obtained which provided approximate solutions to the problem of RPV fracture with assumed beltline region flaws. The first paper of this report is a summary of the problem, the solutions, and the results of verification analyses. The details are provided in a series of appendices in Volumes I and II

RHTF 2, a 1200 MWe high temperature reactor

International Nuclear Information System (INIS)

Brisbois, Jacques

1978-01-01

After having adapted to French conditions the 1160 MWe G.A.C. reactor, Commissariat a l'Energie Atomique and French Industry have decided to design an High Temperature Reactor 1200 MWe based on the G.A.C. technology and taking into account the point of view of Electricite de France and the experience of C.E.A. and industry on the gas cooled reactor technology. The main objective of this work is to produce a reactor design having a low technical risk, good operability, with an emphasis on the safety aspects easing the licensing problems

Biohydrogen production from pig slurry in a CSTR reactor system with mixed cultures under hyper-thermophilic temperature (70 oC)

International Nuclear Information System (INIS)

Kotsopoulos, Thomas A.; Fotidis, Ioannis A.; Tsolakis, Nikolaos; Martzopoulos, Gerassimos G.

2009-01-01

A continuous stirred tank reactor (CSTR) (750 cm 3 working volume) was operated with pig slurry under hyper-thermophilic (70 o C) temperature for hydrogen production. The hydraulic retention time (HRT) was 24 h and the organic loading rate was 24.9 g d -1 of volatile solid (VS). The inoculum used in the hyper-thermophilic reactor was sludge obtained from a mesophilic methanogenic reactor. The continuous feeding with active biomass (inoculum) from the mesophilic methanogenic reactor was necessary in order to achieve hydrogen production. The hyper-thermophilic reactor started to produce hydrogen after a short adapted period of 4 days. During the steady state period the mean hydrogen yield was 3.65 cm 3 g -1 of volatile solid added. The high operation temperature of the reactor enhanced the hydrolytic activity in pig slurry and increased the volatile fatty acids (VFA) production. The short HRT (24 h) and the hyper-thermophilic temperature applied in the reactor were enough to prevent methanogenesis. No pre-treatment methods or other control methods for preventing methanogenesis were necessary. Hyper-thermophilic hydrogen production was demonstrated for the first time in a CSTR system, fed with pig slurry, using mixed culture. The results indicate that this system is a promising one for biohydrogen production from pig slurry.

Long-term adaptation of methanol-fed thermophilic (55°C) sulfate-reducing reactors to NaCl

NARCIS (Netherlands)

Vallero, M.V.G.; Lettinga, G.; Lens, P.N.L.

2003-01-01

A laboratory-scale upflow anaerobic sludge bed (UASB) reactor was operated during 273 days at increasing NaCl concentrations (0.5-12.5 g NaCl l(-1)) to assess whether the stepwise addition of the salt NaCl results in the acclimation of that sludge. The 6.5-1 thermophilic (55 degreesC), sulfidogenic

The modular high-temperature gas-cooled reactor - a new production reactor

International Nuclear Information System (INIS)

Nulton, J.D.

1990-01-01

One of the reactor concepts being considered for application as a new production reactor (NPR) is a 350-MW(thermal) modular high-temperature gas-cooled reactor (MHTGR). The proposed MHTGR-NPR is based on the design of the commercial MHTGR and is being developed by a team that includes General Atomics and Combustion Engineering. The proposed design includes four modules combined into a production block that includes a shared containment, a spent-fuel storage facility, and other support facilities. The MHTGR has a helium-cooled, graphite-moderated, graphite-reflected annular core formed from prismatic graphite fuel blocks. The MHTGR fuel consists of highly enriched uranium oxycarbide (UCO) microsphere fuel particles that are coated with successive layers of pyrolytic carbon (PyC) and silicon carbide (SiC). Tritium-producing targets consist of enriched 6 Li aluminate microsphere target particles that are coated with successive layers of PyC and SiC similar to the fuel microspheres. Normal reactivity control is implemented by articulated control rods that can be inserted into channels in the inner and outer reflector blocks. Shutdown heat removal is accomplished by a single shutdown heat exchanger and electric motor-driven circulator located in the bottom of the reactor vessel. Current plans are to stack spent fuel elements in dry, helium-filled, water-cooled wells and store them for ∼1 yr before reprocessing. All phases of MHTGR fuel reprocessing have been demonstrated

Regulatory use the classification security systems of I and C in VVER type reactors

International Nuclear Information System (INIS)

Ilizastegui Perez, F.

1998-01-01

Presently work the author proposes a classification to the system I and C to the VVER 440 type reactor in categories the regulatory control with a view to establishing the degree to the attention that the regulator should pay to these systems, leaving the importance that have the same ones for the security the installation, during the execution the works that are carried out with this equipment in the stages construction, setting in service and exploitation

Irradiation creep of various ferritic alloys irradiated at {approximately}400{degrees}C in the PFR and FFTF reactors

Energy Technology Data Exchange (ETDEWEB)

Toloczko, M.B.; Garner, F.A. [Pacific Northwest National Lab., Richland, WA (United States); Eiholzer, C.R. [Westinghouse Hanford Company, Richland, WA (United States)

1997-04-01

Three ferritic alloys were irradiated in two fast reactors to doses of 50 dpa or more at temperatures near 400{degrees}C. One martensitic alloy, HT9, was irradiated in both the FFTF and PFR reactors. PFR is the Prototype Fast Reactor in Dourneay, Scotland, and FFTF is the Fast Flux Test Facility in Richland, WA. D57 is a developmental alloy that was irradiated in PFR only, and MA957 is a Y{sub 2}O{sub 3} dispersion-hardened ferritic alloy that was irradiated only in FFTF. These alloys exhibited little or no void swelling at {approximately}400{degrees}C. Depending on the alloy starting condition, these steels develop a variety of non-creep strains early in the irradiation that are associated with phase changes. Each of these alloys creeps at a rate that is significantly lower than that of austenitic steels irradiated in the same experiments. The creep compliance for ferritic alloys in general appears to be {approximately}0.5 x 10{sup {minus}6} MPa{sup {minus}1} dpa{sup {minus}1}, independent of both composition and starting state. The addition of Y{sub 2}O{sub 3} as a dispersoid does not appear to change the creep behavior.

Evaluación del comportamiento hidráulico en un reactor anaerobio de doble cámara (RADCA)

OpenAIRE

Nancy Rincón; Andres Galindo; Jhonny Pérez

2011-01-01

En la remoción de carga orgánica en un sistema de tratamiento de aguas residuales intervienen los procesos bioquímico y aspectos hidrodinámicos como las características de flujo, régimen de mezcla, tiempos de residencia, geometría del reactor, por otro lado las condiciones de flujo no ideal tales como cortos circuitos, zonas muertas y recirculación interna afectan su desempeño. En esta investigación se evaluó el comportamiento hidráulico de un reactor anaerobio de doble cámara (RADCA) de 5...

Nuclear reactor

International Nuclear Information System (INIS)

Schulze, I.; Gutscher, E.

1980-01-01

The core contains a critical mass of UN or U 2 N 3 in the form of a noncritical solution with melted Sn being kept below a N atmosphere. The lining of the reactor core consists of graphite. If fission progresses part of the melted metal solution is removed and cleaned from fission products. The reactor temperatures lie in the range of 300 to 2000 0 C. (Examples and tables). (RW) [de

Fast reactors

International Nuclear Information System (INIS)

Vasile, A.

2001-01-01

Fast reactors have capacities to spare uranium natural resources by their breeding property and to propose solutions to the management of radioactive wastes by limiting the inventory of heavy nuclei. This article highlights the role that fast reactors could play for reducing the radiotoxicity of wastes. The conversion of 238 U into 239 Pu by neutron capture is more efficient in fast reactors than in light water reactors. In fast reactors multi-recycling of U + Pu leads to fissioning up to 95% of the initial fuel ( 238 U + 235 U). 2 strategies have been studied to burn actinides: - the multi-recycling of heavy nuclei is made inside the fuel element (homogeneous option); - the unique recycling is made in special irradiation targets placed inside the core or at its surroundings (heterogeneous option). Simulations have shown that, for the same amount of energy produced (400 TWhe), the mass of transuranium elements (Pu + Np + Am + Cm) sent to waste disposal is 60,9 Kg in the homogeneous option and 204.4 Kg in the heterogeneous option. Experimental programs are carried out in Phenix and BOR60 reactors in order to study the feasibility of such strategies. (A.C.)

Undergraduate reactor control experiment

International Nuclear Information System (INIS)

Edwards, R.M.; Power, M.A.; Bryan, M.

1992-01-01

A sequence of reactor and related experiments has been a central element of a senior-level laboratory course at Pennsylvania State University (Penn State) for more than 20 yr. A new experiment has been developed where the students program and operate a computer controller that manipulates the speed of a secondary control rod to regulate TRIGA reactor power. Elementary feedback control theory is introduced to explain the experiment, which emphasizes the nonlinear aspect of reactor control where power level changes are equivalent to a change in control loop gain. Digital control of nuclear reactors has become more visible at Penn State with the replacement of the original analog-based TRIGA reactor control console with a modern computer-based digital control console. Several TRIGA reactor dynamics experiments, which comprise half of the three-credit laboratory course, lead to the control experiment finale: (a) digital simulation, (b) control rod calibration, (c) reactor pulsing, (d) reactivity oscillator, and (e) reactor noise

Thermodynamic parameters and transport coefficients of the U-C-F gas mixture in the steady flow gaseous core fission reactor

International Nuclear Information System (INIS)

Berg, M.S. van den.

1995-01-01

Thermodynamic parameters and transport coefficients have been calculated for a multicomponent reacting U-C-F gas mixture in the steady flow gaseous core fission reactor. Element abundances are consistent with thermodynamic equilibrium between the gas mixture and a cooled solid graphite wall at 2500 K. Results are presented for various pressures, a fluorine potential of 5.6 and temperatures between 2500 and 7000 K. As a result of dissociation processes of uranium and carbon fluoride compounds, ''effective'' values of thermodynamic parameters and transport coefficients show anomalous behaviour with respect to so-called ''frozen'' values. The chemical reaction energy of the U-C-F gas mixture has been calculated as the driving-force behind the process of fuel redistribution to attain criticality conditions inside a functioning reactor. (author)

Safety and risk assessments for the SNR 300

International Nuclear Information System (INIS)

Maschek, W.; Froehlich, R.; Jacobs, H.; Schikorr, M.; Heusener, G.; Caldarola, L.; Royl, P.; Struwe, D.

1983-01-01

Under the official inquiry ''Future Nuclear Energy Policies'', KfK have carried out a number of studies concerning the hazards arising from core-destructive accidents at the SNR-300 reactor. Among these, there was the so-called ''Upper Limit Study'' providing a critical evaluation of literature on all research done on core-destructive accidents (Bethe-Tait excursion) with a high mechanic energy release potential; the other one was the so-called ''SAI Study'' (a cooperation of KfK, Science Applications, Inc. (SAI) and Interatom (IA)) which investigated the hazards of an uncontrolled coolant flow rate disturbance occurring in the SNR-300 reactor. KfK also took part in the analysis of hazards comparing the SNR-300 reactor with an LWR-type reactor like the one at Biblis B, ordered by the Federal Ministry of Research and Technology (BMFT). These studies have already been dealt with KfK-Nachrichten, 14th annual set issue 4/1982. The article on hand summarizes and evaluates once more the most important results. (orig./RW) [de

Fast reactor cycle calculation routine using a 3D-simulator and investigation of new burnup stategies for pressurized water reactors

International Nuclear Information System (INIS)

Li Yulun.

1987-03-01

Three-dimensional calculations of the longtime behaviour of PWR can be done in short computing times with satisfactory accuracy for power and burn-up distributions. This has been proved by comparison with operational data of Biblis-B. Various possibilities are investigated to increase the discharge burn-up and to improve the utilization of uranium. In view of the increase of discharge burn-up due to enhanced cycle number (decreased batch size) and decreased neutron leakage these new strategies are intensively studied in the conventional fuel management scheme (Out-in) and in the low leakage fuel management scheme (In-Out). By a conventional fuel management scheme with four cycle operation and a low leakage fuel management scheme with three cycle operation an attractive increase of discharge burn-up to about 40% can be achieved by an increase in the reload enrichment to 4%. (orig.) [de

ROP design for Enhanced CANDU 6 reactor

Energy Technology Data Exchange (ETDEWEB)

Hu, J.; Scherbakova, D; Kastanya, D.; Ovanes, M. [Candu Energy Inc., Mississauga, Ontario (Canada)

2011-07-01

The Enhanced CANDU 6 (EC6) nuclear power plant is a mid-sized pressurized heavy water reactor design, based on the highly successful CANDU 6 (C6) family of power plants, upgraded to meet today's Canadian and international safety requirements and to satisfy Generation III expectations. The EC6 reactor is equipped with two independent Regional Overpower Protection (ROP) systems to prevent overpowers in the reactor fuel. The ROP system design, retaining the traditional C6 methodology, is determined to cover the End-of-Life (EOL) reactor core condition since the reactor operating/thermal margin gradually decreases as plant equipment ages. Several design changes have been incorporated into the reference C6 plant to mitigate the ageing effect on the ROP trip margin. This paper outlines the basis for the EC6 ROP physics design and presents the ROP related improvements made in the EC6 design to ensure that full power operation is not limited by the ROP throughout the entire life of the reactor. (author)

Development of M3C code for Monte Carlo reactor physics criticality calculations

International Nuclear Information System (INIS)

Kumar, Anek; Kannan, Umasankari; Krishanani, P.D.

2015-06-01

The development of Monte Carlo code (M3C) for reactor design entails use of continuous energy nuclear data and Monte Carlo simulations for each of the neutron interaction processes. BARC has started a concentrated effort for developing a new general geometry continuous energy Monte Carlo code for reactor physics calculation indigenously. The code development required a comprehensive understanding of the basic continuous energy cross section sets. The important features of this code are treatment of heterogeneous lattices by general geometry, use of point cross sections along with unionized energy grid approach, thermal scattering model for low energy treatment, capability of handling the microscopic fuel particles dispersed randomly. The capability of handling the randomly dispersed microscopic fuel particles which is very useful for the modeling of High-Temperature Gas-Cooled reactor fuels which are composed of thousands of microscopic fuel particle (TRISO fuel particle), randomly dispersed in a graphite matrix. The Monte Carlo code for criticality calculation is a pioneering effort and has been used to study several types of lattices including cluster geometries. The code has been verified for its accuracy against more than 60 sample problems covering a wide range from simple (like spherical) to complex geometry (like PHWR lattice). Benchmark results show that the code performs quite well for the criticality calculation of the system. In this report, the current status of the code, features of the code, some of the benchmark results for the testing of the code and input preparation etc. are discussed. (author)

Removal Site Evaluation Report to the C-Reactor Seepage Basins (904-066, -067 and -068G)

Energy Technology Data Exchange (ETDEWEB)

Palmer, E.R. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1997-07-01

Removal Site Evaluation Reports are prepared in accordance with Section 300.410 of the National Contingency Plan (NCP) and Section X of the Federal Facility Agreement (FFA). The C-Reactor Seepage Basins (904-066G,-067G,-068G) are listed in Appendix C, Resource Conservation and Recovery Act (RCRA)/Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Units List, of the FFA. The purpose of this investigation is to report information concerning conditions at this unit sufficient to assess the threat (if any) posed to human health and the environment and to determine the need for additional CERCLA action. The scope of the investigation included a review of past survey and investigation data, the files, and a visit to the unit.Through this investigation unacceptable conditions of radioactive contaminant uptake in on-site vegetation were identified. This may have resulted in probable contaminant migration and become introduced into the local ecological food chain. As a result, the SRS will initiate a time critical removal action in accordance with Section 300.415 of the NCP and FFA Section XIV to remove, treat (if required), and dispose of contaminated vegetation from the C-Reactor Seepage Basins. Erosion in the affected areas will be managed by an approved erosion control plan. further remediation of this unit will be conducted in accordance with the FFA.

Removal Site Evaluation Report to the C-Reactor Seepage Basins (904-066, -067 and -068G)

International Nuclear Information System (INIS)

Palmer, E.R.

1997-07-01

Removal Site Evaluation Reports are prepared in accordance with Section 300.410 of the National Contingency Plan (NCP) and Section X of the Federal Facility Agreement (FFA). The C-Reactor Seepage Basins (904-066G,-067G,-068G) are listed in Appendix C, Resource Conservation and Recovery Act (RCRA)/Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Units List, of the FFA. The purpose of this investigation is to report information concerning conditions at this unit sufficient to assess the threat (if any) posed to human health and the environment and to determine the need for additional CERCLA action. The scope of the investigation included a review of past survey and investigation data, the files, and a visit to the unit.Through this investigation unacceptable conditions of radioactive contaminant uptake in on-site vegetation were identified. This may have resulted in probable contaminant migration and become introduced into the local ecological food chain. As a result, the SRS will initiate a time critical removal action in accordance with Section 300.415 of the NCP and FFA Section XIV to remove, treat (if required), and dispose of contaminated vegetation from the C-Reactor Seepage Basins. Erosion in the affected areas will be managed by an approved erosion control plan. further remediation of this unit will be conducted in accordance with the FFA

Software development methodology for computer based I&C systems of prototype fast breeder reactor

International Nuclear Information System (INIS)

Manimaran, M.; Shanmugam, A.; Parimalam, P.; Murali, N.; Satya Murty, S.A.V.

2015-01-01

Highlights: • Software development methodology adopted for computer based I&C systems of PFBR is detailed. • Constraints imposed as part of software requirements and coding phase are elaborated. • Compliance to safety and security requirements are described. • Usage of CASE (Computer Aided Software Engineering) tools during software design, analysis and testing phase are explained. - Abstract: Prototype Fast Breeder Reactor (PFBR) is sodium cooled reactor which is in the advanced stage of construction in Kalpakkam, India. Versa Module Europa bus based Real Time Computer (RTC) systems are deployed for Instrumentation & Control of PFBR. RTC systems have to perform safety functions within the stipulated time which calls for highly dependable software. Hence, well defined software development methodology is adopted for RTC systems starting from the requirement capture phase till the final validation of the software product. V-model is used for software development. IEC 60880 standard and AERB SG D-25 guideline are followed at each phase of software development. Requirements documents and design documents are prepared as per IEEE standards. Defensive programming strategies are followed for software development using C language. Verification and validation (V&V) of documents and software are carried out at each phase by independent V&V committee. Computer aided software engineering tools are used for software modelling, checking for MISRA C compliance and to carry out static and dynamic analysis. Various software metrics such as cyclomatic complexity, nesting depth and comment to code are checked. Test cases are generated using equivalence class partitioning, boundary value analysis and cause and effect graphing techniques. System integration testing is carried out wherein functional and performance requirements of the system are monitored

Software development methodology for computer based I&C systems of prototype fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Manimaran, M., E-mail: maran@igcar.gov.in; Shanmugam, A.; Parimalam, P.; Murali, N.; Satya Murty, S.A.V.

2015-10-15

Highlights: • Software development methodology adopted for computer based I&C systems of PFBR is detailed. • Constraints imposed as part of software requirements and coding phase are elaborated. • Compliance to safety and security requirements are described. • Usage of CASE (Computer Aided Software Engineering) tools during software design, analysis and testing phase are explained. - Abstract: Prototype Fast Breeder Reactor (PFBR) is sodium cooled reactor which is in the advanced stage of construction in Kalpakkam, India. Versa Module Europa bus based Real Time Computer (RTC) systems are deployed for Instrumentation & Control of PFBR. RTC systems have to perform safety functions within the stipulated time which calls for highly dependable software. Hence, well defined software development methodology is adopted for RTC systems starting from the requirement capture phase till the final validation of the software product. V-model is used for software development. IEC 60880 standard and AERB SG D-25 guideline are followed at each phase of software development. Requirements documents and design documents are prepared as per IEEE standards. Defensive programming strategies are followed for software development using C language. Verification and validation (V&V) of documents and software are carried out at each phase by independent V&V committee. Computer aided software engineering tools are used for software modelling, checking for MISRA C compliance and to carry out static and dynamic analysis. Various software metrics such as cyclomatic complexity, nesting depth and comment to code are checked. Test cases are generated using equivalence class partitioning, boundary value analysis and cause and effect graphing techniques. System integration testing is carried out wherein functional and performance requirements of the system are monitored.

Manufacture of components for Canadian reactor programs

International Nuclear Information System (INIS)

Perry, L.P.

Design features, especially those relating to calandrias, are pointed out for many CANDU-type reactors and the Taiwan research reactor. The special requirements shouldered by the Canadian suppliers of heavy reactor components are analyzed. (E.C.B.)

Engineering reactors for catalytic reactions

Indian Academy of Sciences (India)

126, No. 2, March 2014, pp. 341–351. c Indian Academy of Sciences. ... enhancement was realized by catalyst design, appropriate choice of reactor, better injection and .... Gas–liquid and liquid–solid transport processes in catalytic reactors.5.

Lead- or Lead-bismuth-cooled fast reactors

International Nuclear Information System (INIS)

Bouchter, J.C.; Courouau, J.L.; Dufour, P.; Guidez, J.; Latge, C.; Martinelli, L.; Renault, C.; Rimpault, G.

2014-01-01

Lead-cooled fast reactors are one of the 6 concepts retained for the 4. generation of nuclear reactors. So far no lead-cooled reactors have existed in the world except lead-bismuth-cooled reactors in soviet submarines. Some problems linked to the use of the lead-bismuth eutectic appeared but were satisfactorily solved by a more rigorous monitoring of the chemistry of the lead-bismuth coolant. Lead presents various advantages as a coolant: no reactivity with water and the air,a high boiling temperature and low contamination when irradiated. The main asset of the lead-bismuth alloy is the drop of the fusion temperature from 327 C degrees to 125 C degrees. The main drawback of using lead (or lead-bismuth) is its high corrosiveness with metals like iron, chromium and nickel. The high corrosiveness of the coolant implies low flow velocities which means a bigger core and consequently a bigger reactor containment. Different research programs in the world (in Europe, Russia and the USA) are reviewed in the article but it appears that the development of this type of reactor requires technological breakthroughs concerning materials and the resistance to corrosion. Furthermore the concept of lead-cooled reactors seems to be associated to a range of low output power because of the compromise between the size of the reactor and its resistance to earthquakes. (A.C.)

Method of reactor operation

International Nuclear Information System (INIS)

Maeda, Katsuji.

1982-01-01

Purpose: To prevent stress corrosion cracks in stainless steels caused from hydrogen peroxide in reactor operation in which the density of hydrogen peroxide in the reactor water is controlled upon reactor start-up. Method: A heat exchanger equipped with a heat source for applying external heat is disposed into the recycling system for reactor coolants. Upon reactor start-up, the coolants are heated by the heat exchanger till arriving at a temperature at which the dissolving rate is faster than the forming rate of hydrogen peroxide in the coolants, and nuclear heating is started after reaching the above temperature. The temperature of the reactor water is increased in such a manner and, when it arrives at 140 0 C, extraction of control elements is started and the heat source for the heat exchanger is interrupted simultaneously. In this way spikes in the density of hydrogen peroxide are suppressed upon reactor start-up to thereby decrease the stress corrosion cracks in stainless steels. (Horiuchi, T.)

Selection of operations staff, qualifications and experience

International Nuclear Information System (INIS)

Gutmann, H.

1977-01-01

Requirements and suggestions have been made by authorities and various organisations in a number of countries which define necessary experience and training for the various groups of nuclear power plant personnel. For two countries, the USA and the FRG, a comparison has been made which shows that there is only a slight deviation, taking into account the different education systems. With the example of the Biblis nuclear power plant the training on the job is described. Especially the production or operation department is looked at in more detail. The training is split up into several parts: a general part, such as nuclear physics, reactor physics and engineering, reactor safety, radiation protection and so on and a plant related part, such as arrangement and mode of operation of the plant under normal and accident conditions, license conditions and so on. (orig.) [de

Pebble bed reactors simulation using MCNP: The Chinese HTR-10 reactor

Directory of Open Access Journals (Sweden)

SA Hosseini

2013-09-01

Full Text Available   Given the role of Gas-Graphite reactors as the fourth generation reactors and their recently renewed importance, in 2002 the IAEA proposed a set of Benchmarking problems. In this work, we propose a model both efficient in time and resources and exact to simulate the HTR-10 reactor using MCNP-4C code. During the present work, all of the pressing factors in PBM reactor design such as the inter-pebble leakage, fuel particle distribution and fuel pebble packing fraction effects have been taken into account to obtain an exact and easy to run model. Finally, the comparison between the results of the present work and other calculations made at INEEL proves the exactness of the proposed model.

Potential market and characteristics of low-temperature reactors

International Nuclear Information System (INIS)

Lerouge, B.

1975-01-01

The low-temperature (100 to 200 deg C) heat market for industrial applications and district heating is very important. Two main studies have been developed: a swimming pool reactor delivering water at 110 deg C and a prestressed concrete vessel reactor delivering water at 200 deg C [fr

Simultaneous C and N removal from saline salmon effluents in filter reactors comprising anoxic-anaerobic-aerobic processes: effect of recycle ratio.

Science.gov (United States)

Giustinianovich, Elisa A; Aspé, Estrella R; Huiliñir, César E; Roeckel, Marlene D

2014-01-01

Salmon processing generates saline effluents with high protein load. To treat these effluents, three compact tubular filter reactors were installed and an integrated anoxic/anaerobic/aerobic process was developed with recycling flow from the reactor's exit to the inlet stream in order to save organic matter (OM) for denitrification. The reactors were aerated in the upper section with recycle ratios (RR) of 0, 2, and 10, respectively, at 30°C. A tubular reactor behave as a plug flow reactor when RR = 0, and as a mixed flow reactor when recycle increases, thus, different RR values were used to evaluate how it affects the product distribution and the global performance. Diluted salmon process effluent was prepared as substrate. Using loads of 1.0 kg COD m(-3)d(-1) and 0.15 kg total Kjeldahl nitrogen (TKN) m(-3)d(-1) at HRT of 2 d, 100% removal efficiencies for nitrite and nitrate were achieved in the anoxic-denitrifying section without effect of the dissolved oxygen in the recycled flow on denitrification. Removals >98% for total organic carbon (TOC) was achieved in the three reactors. The RR had no effect on the TOC removal; nevertheless a higher efficiency in total nitrogen removal in the reactor with the highest recycle ratio was observed: 94.3% for RR = 10 and 46.6% for RR = 2. Results showed that the proposed layout with an alternative distribution in a compact reactor can efficiently treat high organic carbon and nitrogen concentrations from a saline fish effluent with OM savings in denitrification.

Effect of NaCl on thermophilic (55°C) methanol degradation in sulfate reducing granular sludge reactors

NARCIS (Netherlands)

Vallero, M.V.G.; Hulshoff Pol, L.W.; Lettinga, G.; Lens, P.N.L.

2003-01-01

The effect of NaCl on thermophilic (55degreesC) methanol conversion in the presence of excess of sulfate (COD/SO42-=0.5) was investigated in two 6.5L lab-scale upflow anaerobic sludge bed reactors inoculated with granular sludge previously not adapted to NaCl
The effect of NaCl on thermophilic

Reactor core design optimization of the 200 MWt Pb-Bi cooled fast reactor for hydrogen production

International Nuclear Information System (INIS)

Bahrum, Epung Saepul; Su'ud, Zaki; Waris, Abdul; Fitriyani, Dian; Wahjoedi, Bambang Ari

2008-01-01

In this study reactor core geometrical optimization of 200 MWt Pb-Bi cooled long life fast reactor for hydrogen production has been conducted. The reactor life time is 20 years and the fuel type is UN-PuN. Geometrical core configurations considered in this study are balance, pancake and tall cylindrical cores. For the hydrogen production unit we adopt steam membrane reforming hydrogen gas production. The optimum operating temperature for the catalytic reaction is 540degC. Fast reactor design optimization calculation was run by using FI-ITB-CHI software package. The design criteria were restricted by the multiplication factor that should be less than 1.002, the average outlet coolant temperature 550degC and the maximum coolant outlet temperature less than 700degC. By taking into account of the hydrogen production as well as corrosion resulting from Pb-Bi, the balance cylindrical geometrical core design with diameter and height of the active core of 157 cm each, the inlet coolant temperature of 350degC and the coolant flow rate of 7000 kg/s were preferred as the best design parameters. (author)

Reactor operation method

International Nuclear Information System (INIS)

Osumi, Katsumi; Miki, Minoru.

1979-01-01

Purpose: To prevent stress corrosion cracks by decreasing the dissolved oxygen and hydrogen peroxide concentrations in the coolants within a reactor container upon transient operation such as at the start-up or shutdown of bwr type reactors. Method: After a condensate has been evacuated, deaeration operation is conducted while opening a main steam drain line, as well as a main steam separation valve and a by-pass valve in a turbine by-pass line connecting the main steam line and the condenser without by way of a turbine, and the reactor is started-up by the extraction of control rods after the concentration of dissolved oxygen in the cooling water within a pressure vessel has been decreased below a predetermined value. Nuclear heating is started after the reactor water has been increased to about 150 0 C by pump heating after the end of the deaeration operation for preventing the concentration of hydrogen peroxide and oxygen in the reactor water from temporarily increasing immediately after the start-up. The corrosive atmosphere in the reactor vessel can thus be moderated. (Horiuchi, T.)

Evaluación del comportamiento hidráulico en un reactor anaerobio de doble cámara (RADCA

Directory of Open Access Journals (Sweden)

Nancy Rincón

2011-01-01

tales como cortos circuitos, zonas muertas y recirculación interna afectan su desempeño. En esta investigación se evaluó el comportamiento hidráulico de un reactor anaerobio de doble cámara (RADCA de 534,5 L (cámara 1=305 L y cámara 2= 229,5 L como innovación tecnológica de los reactores UASB. El RADCA fue alimentado con agua residual municipal (ARM de la ciudad de Maracaibo, Venezuela; cada una de las cámaras fueron inoculadas con lodo granular (20% v/v proveniente de una cervecería local. La evaluación hidráulica se realizó en la fase líquida y en operación utilizando Li+ (LiCl como trazador aplicado de forma instantánea en el afluente a tiempo de retención hidráulico teórico (TRHt de 6 horas; 3,4 h en la cámara 1 y 2,6 para la cámara 2. El RADCA describió un flujo pistón en ambas cámaras y una eficiencia hidráulica cercana a la unidad (1 indicando una presencia casi nula de zonas muertas. La eficiencia de remoción de la DQO total (DQOT del RADCA se mantuvo en el rango de 59,77% a 74,64% con un promedio de 68,26%. Para las cámaras 1 y 2 la eficiencia promedio fue 60,4 y 20,94% con una producción de biogás (L/h de 2,768 y 0,541 respectivamente.

Fast neutron reactor core research at the C.E.A

International Nuclear Information System (INIS)

Chaudat, J.-P.

1978-05-01

This report covers all physical studies of fast neutron reactors carried out by the C.E.A., to povide basic data (multi-group cross sections) and computer methods which may be used to calculate nuclear power plant neutron properties with the precision required by the project. The approach adopted to establish the basic data used in all core calculations is described in greated detail: choice of a reference procedure for basic mode calculations (CARNAVAL set), choice of particular experimental programs to reduce uncertainties in connection with the formula set, adjustement of cross sections on integral parameters measured on critical experiments. The development of the formula set is closely connected with the project requirements; hence the set is modified with respect to the core characteristics of the power plant studied. Following an explanation of how the CARNAVAL III and IV formula sets -used for PHENIX and SUPER-PHENIX respectively- were derived, current studies for heterogeneous cores are described [fr

Station Blackout Analysis of HTGR-Type Experimental Power Reactor

Science.gov (United States)

Syarip; Zuhdi, Aliq; Falah, Sabilul

2018-01-01

The National Nuclear Energy Agency of Indonesia has decided to build an experimental power reactor of high-temperature gas-cooled reactor (HTGR) type located at Puspiptek Complex. The purpose of this project is to demonstrate a small modular nuclear power plant that can be operated safely. One of the reactor safety characteristics is the reliability of the reactor to the station blackout (SBO) event. The event was observed due to relatively high disturbance frequency of electricity network in Indonesia. The PCTRAN-HTR functional simulator code was used to observe fuel and coolant temperature, and coolant pressure during the SBO event. The reactor simulated at 10 MW for 7200 s then the SBO occurred for 1-3 minutes. The analysis result shows that the reactor power decreases automatically as the temperature increase during SBO accident without operator’s active action. The fuel temperature increased by 36.57 °C every minute during SBO and the power decreased by 0.069 MW every °C fuel temperature rise at the condition of anticipated transient without reactor scram. Whilst, the maximum coolant (helium) temperature and pressure are 1004 °C and 9.2 MPa respectively. The maximum fuel temperature is 1282 °C, this value still far below the fuel temperature limiting condition i.e. 1600 °C, its mean that the HTGR has a very good inherent safety system.

Final hazard classification and auditable safety analysis for the 105-C Reactor Interim Safe Storage Project

International Nuclear Information System (INIS)

Rodovsky, T.J.; Larson, A.R.; Dexheimer, D.

1996-12-01

This document summarizes the inventories of radioactive and hazardous materials present in the 105-C Reactor Facility and the operations associated with the Interim Safe Storage Project which includes decontamination and demolition and interim safe storage of the remaining facility. This document also establishes a final hazard classification and verifies that appropriate and adequate safety functions and controls are in place to reduce or mitigate the risk associated with those operations

Environmental consequences of alternatives to L Reactor restart

International Nuclear Information System (INIS)

1983-01-01

Alternatives to renewed L-Reactor operation for increased production of nuclear materials are: restart of R Reactor, construction and operation of a New Production Reactor (NPR), increased throughput of SRP reactors C, K, and P and N Reactor at Hanford, restart of K Reactors at Hanford, and no action - standby ready state for L Reactor. This report compares the environmental consequences from the proposed L-Reactor restart and these alternatives. The environmental consequences considered are radiological releases, radiocesium remobilization, nonradiological releases, ecological impacts and transportation

New instrumentation for the IPR-R1 reactor of CDTN

International Nuclear Information System (INIS)

Carvalho, P.V.R. de.

1992-01-01

The Nuclear Engineering Institute reactor instrumentation area has developed systems and equipment for reactor operation and safety. In such way, the new I and C for IEN Argonauta reactor and the nuclear instrumentation for IPEN critical facility were built. This paper describes our real work, the new I and C systems for IPR-R1, a Triga type reactor, located at CDTN (Belo Horizonte - MG). (author)

Effects of C/N ratio on nitrous oxide production from nitrification in a laboratory-scale biological aerated filter reactor.

Science.gov (United States)

He, Qiang; Zhu, Yinying; Fan, Leilei; Ai, Hainan; Huangfu, Xiaoliu; Chen, Mei

2017-03-01

Emission of nitrous oxide (N 2 O) during biological wastewater treatment is of growing concern. This paper reports findings of the effects of carbon/nitrogen (C/N) ratio on N 2 O production rates in a laboratory-scale biological aerated filter (BAF) reactor, focusing on the biofilm during nitrification. Polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and microelectrode technology were utilized to evaluate the mechanisms associated with N 2 O production during wastewater treatment using BAF. Results indicated that the ability of N 2 O emission in biofilm at C/N ratio of 2 was much stronger than at C/N ratios of 5 and 8. PCR-DGGE analysis showed that the microbial community structures differed completely after the acclimatization at tested C/N ratios (i.e., 2, 5, and 8). Measurements of critical parameters including dissolved oxygen, oxidation reduction potential, NH 4 + -N, NO 3 - -N, and NO 2 - -N also demonstrated that the internal micro-environment of the biofilm benefit N 2 O production. DNA analysis showed that Proteobacteria comprised the majority of the bacteria, which might mainly result in N 2 O emission. Based on these results, C/N ratio is one of the parameters that play an important role in the N 2 O emission from the BAF reactors during nitrification.

Power monitoring in space nuclear reactors using silicon carbide radiation detectors

Science.gov (United States)

Ruddy, Frank H.; Patel, Jagdish U.; Williams, John G.

2005-01-01

Space reactor power monitors based on silicon carbide (SiC) semiconductor neutron detectors are proposed. Detection of fast leakage neutrons using SiC detectors in ex-core locations could be used to determine reactor power: Neutron fluxes, gamma-ray dose rates and ambient temperatures have been calculated as a function of distance from the reactor core, and the feasibility of power monitoring with SiC detectors has been evaluated at several ex-core locations. Arrays of SiC diodes can be configured to provide the required count rates to monitor reactor power from startup to full power Due to their resistance to temperature and the effects of neutron and gamma-ray exposure, SiC detectors can be expected to provide power monitoring information for the fill mission of a space reactor.

Research reactor instrumentation and control technology. Report of a technical committee meeting

International Nuclear Information System (INIS)

1997-10-01

The majority of research reactors operating today were put into operation 20 years ago, and some of them underwent modifications, upgrading and refurbishing since their construction to meet the requirements for higher neutron fluxes. However, a few of these ageing research reactors are still operating with their original instrumentation and control systems (I and C) which are important for reactor safety to guard against abnormal occurrences and reactor control involving startup, shutdown and power regulation. Worn and obsolete I and C systems cause operational problems as well as difficulties in obtaining replacement parts. In addition, satisfying the stringent safety conditions laid out by the nuclear regulatory bodies requires the modernization of research reactors I and C systems and integration of additional instrumentation units to the reactor. In order to clarify these issues and to provide some guidance to reactor operators on state-of-art technology and future trends for the I and C systems for research reactors, a Technical Committee Meeting on Technology and Trends for Research Reactor Instrumentation and Controls was held in Ljubljana, Slovenia, from 4 to 8 December 1995. This publication summarizes the discussions and recommendations resulting from that meeting. This is expected to benefit the research reactor operators planning I and C improvements. Refs, figs, tabs

Gas leak tightness of SiC/SiC composites at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Hayasaka, Daisuke, E-mail: hayasaka@oasis.muroran-it.ac.jp [OASIS, Muroran Institute of Technology, Muroran, Hokkaido (Japan); Graduate School of Engineering, Muroran Institute of Technology, Muroran, Hokkaido (Japan); Park, Joon-Soo. [OASIS, Muroran Institute of Technology, Muroran, Hokkaido (Japan); Kishimoto, Hirotatsu [OASIS, Muroran Institute of Technology, Muroran, Hokkaido (Japan); Graduate School of Engineering, Muroran Institute of Technology, Muroran, Hokkaido (Japan); Kohyama, Akira [OASIS, Muroran Institute of Technology, Muroran, Hokkaido (Japan)

2016-11-01

Highlights: • NITE-SiC/SiC has extremely densified microstructure compared with other SiC/SiC composite like CVI. • Excellent helium and hydrogen gas-leak tightness of SiC/SiC composites by DEMO-NITE method from prototype industrialization production line was presented. • The excellence against stainless steel and Zircaloy at elevated temperature, together with generic excellent properties of SiC will be inevitable for innovative blanket and divertors for DEMO- and power- fusion reactors. - Abstract: SiC/SiC composite materials are attractive candidates for high heat flux components and blanket of fusion reactor, mainly due to their high temperature properties, radiation damage tolerance and low induced radioactivity. One of the challenges for SiC/SiC application in fusion reactors is to satisfy sufficient gas leak tightness of hydrogen and helium isotopes. Although many efforts have been carried-out, SiC/SiC composites by conventional processes have not been successful to satisfy the requirements, except SiC/SiC composites by NITE-methods. Toward the early realization of SiC/SiC components into fusion reactor systems process development of NITE-process has been continued. Followed to the brief introduction of recently developed DEMO-NITE process, baseline properties and hydrogen and helium gas leak tightness is presented. SiC/SiC claddings with 10 mm in diameter and 1 mm in wall thickness are tested by gas leak tightness system developed. The leak tightness measurements are done room temperature to 400 °C. Excellent gas leak tightness equivalent or superior to Zircaloy claddings for light water fission reactors is confirmed. The excellent gas leak tightness suggests nearly perfect suppression of large gas leak path in DEMO-NITE SiC/SiC.

Molten salt reactors

International Nuclear Information System (INIS)

Bouchter, J.C.; Dufour, P.; Guidez, J.; Simon, N.; Renault, C.

2014-01-01

Molten salt reactors are one of the 6 concepts retained for the 4. generation of nuclear reactors. The principle of this reactor is very innovative: the nuclear fuel is dissolved in the coolant which allows the online reprocessing of the fuel and the online recovery of the fission products. A small prototype: the Molten Salt Reactor Experiment (MSRE - 8 MWt) was operating a few years in the sixties in the USA. The passage towards a fast reactor by the suppression of the graphite moderator leads to the concept of Molten Salt Fast Reactor (MSFR) which is presently studied through different European projects such as MOST, ALISIA and EVOL. Worldwide the main topics of research are: the adequate materials resisting to the high level of corrosiveness of the molten salts, fuel salt reprocessing, the 3-side coupling between neutron transport, thermohydraulics and thermo-chemistry, the management of the changing chemical composition of the salt, the enrichment of lithium with Li 7 in the case of the use of lithium fluoride salt and the use of MSFR using U 233 fuel (thorium cycle). The last part of the article presents a preliminary safety analysis of the MSFR. (A.C.)

State of development of high temperature gas-cooled reactors in foreign countries

International Nuclear Information System (INIS)

Sudo, Yukio

1990-01-01

Emphasis has been placed in the development of high temperature gas-cooled reactors on high thermal efficiency as power reactors and the reactor from which nuclear heat can be utilized. In U.K., as the international project 'Dragon Project', the experimental Dragon reactor for research use with 20 MWt output and exit coolant temperature 750 deg C was constructed, and operated till 1976. Coated fuel particles were developed. In West Germany, the experimental power reactor AVR with 46 MWt and 15 MWe output was operated till 1988. The prototype power reactor THTR-300 with 300 MWe output and 750 deg C exit temperature is in commercial operation. In USA, the experimental power reactor Peach Bottom reactor with 40 MWe output and 728 deg C exit temperature was operated till 1974. The prototype Fort Saint Vrain power reactor with 330 MWe output and 782 deg C exit temperature was operated till 1989. In USSR, the modular VGM with 200 MWh output is at the planning stage. Also in China, high temperature gas-cooled reactors are at the design stage. Switzerland has taken part in various international projects. (K.I.)

Instrumentation and control improvements at Experimental Breeder Reactor II

International Nuclear Information System (INIS)

Christensen, L.J.; Planchon, H.P.

1993-01-01

The purpose of this paper is to describe instrumentation and control (I ampersand C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I ampersand C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I ampersand C systems of the next generation of liquid metal reactor (LMR) plants

Studies of a modular advanced stellarator reactor ASRA6C

International Nuclear Information System (INIS)

Boehme, G.; Jentzsch, K.; Komarek, P.; Maurer, W.; El-Guebaly, L.A.; Emmert, G.A.; Kulcinski, G.L.; Larsen, E.M.; Sanatarius, J.F.; Schawan, M.E.; Scharer, J.E.; Sviatoslavski, I.N.; Vogelsang, W.F.; Walstrom, P.L.; Wittenberg, L.J.; Grieger, G.; Harmeyer, E.; Herrnegger, F.; Kisslinger, J.; Rau, F.; Wobig, H.

1987-05-01

This study is directed towards the clarification of critical issues of advanced modular stellerator reactors exploiting the inherent potential of steady state operation, and is not a point design study of a reactor. Critical technology issues arise from the three-dimensional magnetic field structure. The first wall, blanket and shield are more complex than those of axi-symmetric systems, but this is eased at moderate to large aspect ratio typical of stellerators. Several blanket options have been studied and a thin blanket (21 cm) was the first choice for the design. Superconducting modular coils were investigated with respect to the conductor and mechanical supports. From the analysis of forces and stresses caused by the electromagnetic loads the coils are considered to be feasible, although shear stresses might pose a critical issue. Demountable intermagnetic support elements were designed for use at separation areas between the cryostat modules. A scheme for remote reactor maintenance was also developed. The plasma physics issues of different configurations were studied using extrapolations of transort behaviour and equilibrium from theory and present experiments. These studies indicate that the confinement and equilibrium behaviour is adequate for ignited operation at an average value of 5% beta. Impurities may pose a critical issue. Several impurity control operations were investigated; a pumped limiter configuration utilizing the 'ergodic layer' at the plasma edge was chosen for edge plasma and impurity control. A general conclusion of the study is that the modular stellerator configuration offers interesting prospects regarding the development towards steady-state reactors. (orig.)

Studies of a modular advanced stellarator reactor ASRA6C

International Nuclear Information System (INIS)

Boehme, G.; El-Guebaly, L.A.; Emmert, G.A.; Grieger, G.; Harmeyer, E.; Herrnegger, F.; Huebener, J.; Jentzsch, K.; Kisslinger, J.; Komarek, P.; Kulcinski, G.L.; Larsen, E.M.; Maurer, W.; Rau, F.; Santarius, J.F.; Sawan, M.E.; Scharer, J.E.; Sviatoslavsky, I.N.; Vogelsang, W.F.; Walstrom, P.L.; Wittenberg, L.J.; Wobig, H.

1987-06-01

This study is directed towards the clarification of critical issues of advanced modular stellerator reactors exploiting the inherent potential of steady state operation, and is not a point design study of a reactor. Critical technology issues arise from the three-dimensional magnetic field structure. The first wall, blanket and shield are more complex than those of axi-symmetric systems, but this is eased at moderate to large aspect ratio typical of stellarators. Several blanket options have been studied and a thin blanket (21 cm) was the first choice for the design. Superconducting modular coils were investigated with respect to the conductor and mechanical supports. From the analysis of forces and stresses caused by the electromagnetic loads the coils are considered to be feasible, although shear stresses might pose a critical issue. Demountable intermagnetic support elements were designed for use at separation areas between the cryostat modules. A scheme for remote reactor maintenance was also developed. The plasma physics issues of different configurations were studied using extrapolations of transport behaviour and equilibrium from theory and present experiments. These studies indicate that the confinement and equilibrium behaviour is adequate for ignited operation at an average value of 5% beta. Impurities may pose a critical issue. Several impurity control operations were investigated; a pumped limiter configuration utilizing the 'ergodic layer' at the plasma edge was chosen for edge plasma and impurity control. A general conclusion of the study is that the modular stellerator configuration offers interesting prospects regarding the development towards steady-state reactors. (orig.) [de

Advances in light water reactor technologies

CERN Document Server

Saito, Takehiko; Ishiwatari, Yuki; Oka, Yoshiaki

2010-01-01

""Advances in Light Water Reactor Technologies"" focuses on the design and analysis of advanced nuclear power reactors. This volume provides readers with thorough descriptions of the general characteristics of various advanced light water reactors currently being developed worldwide. Safety, design, development and maintenance of these reactors is the main focus, with key technologies like full MOX core design, next-generation digital I&C systems and seismic design and evaluation described at length. This book is ideal for researchers and engineers working in nuclear power that are interested

Fuel recycling and 4. generation reactors

International Nuclear Information System (INIS)

Devezeaux de Lavergne, J.G.; Gauche, F.; Mathonniere, G.

2012-01-01

The 4. generation reactors meet the demand for sustainability of nuclear power through the saving of the natural resources, the minimization of the volume of wastes, a high safety standard and a high reliability. In the framework of the GIF (Generation 4. International Forum) France has decided to study the sodium-cooled fast reactor. Fast reactors have the capacity to recycle plutonium efficiently and to burn actinides. The long history of reprocessing-recycling of spent fuels in France is an asset. A prototype reactor named ASTRID could be entered into operation in 2020. This article presents the research program on the sodium-cooled fast reactor, gives the status of the ASTRID project and present the scenario of the progressive implementation of 4. generation reactors in the French reactor fleet. (A.C.)

Integrity of the first wall in fusion reactors

International Nuclear Information System (INIS)

Kurihara, Ryoichi

2004-07-01

Future fusion power reactors DREAM and A-SSTR2, which have been conceptually designed in the Japan Atomic Energy Research Institute, use the SiC/SiC composite material as the first wall of the blanket because of its characteristics of high heat-resistance and low radiation material. DEMO reactor, which was conceptually designed in 2001, uses the low activation ferritic steel as the first-wall material of the blanket. The problems in the thermal structural design of the plasma facing component such as the blanket first wall and the divertor plate which receives very high heat flux were examined in the design of the fusion power reactors. Compact high fusion power reactor must give high heat flux and high-speed neutron flux from the plasma to the first wall and the divertor plate. In this environmental situation, the micro cracks should be generated in material of the first wall. Structural integrity of the first wall would be very low during the operation of the reactor, if those micro-cracks grow in a crack having significant size by the fatigue or the creep. The crack penetration in the first wall can be a factor which threatens the safety of the fusion power reactor. This paper summarizes the problems on the structural integrity in the first wall made of the SiC/SiC composite material or the ferritic steel. (author)

Calcium oxide/carbon dioxide reactivity in a packed bed reactor of a chemical heat pump for high-temperature gas reactors

International Nuclear Information System (INIS)

Kato, Yukitaka; Yamada, Mitsuteru; Kanie, Toshihiro; Yoshizawa, Yoshio

2001-01-01

The thermal performance of a chemical heat pump that uses a calcium oxide/carbon dioxide reaction system was discussed as a heat storage system for utilizing heat output from high temperature gas reactors (HTGR). Calcium oxide/carbon dioxide reactivity for the heat pump was measured using a packed bed reactor containing 1.0 kg of reactant. The reactor was capable of storing heat at 900 deg. C by decarbonation of calcium carbonate and generating up to 997 deg. C by carbonation of calcium oxide. The amount of stored heat in the reactor was 800-900 kJ kg -1 . The output temperature of the reactor could be controlled by regulating the carbonation pressure. The thermal storage performance of the reactor was superior to that of conventional sensible heat storage systems. A heat pump using this CaO/CO 2 reactor is expected to contribute to thermal load leveling and to realize highly efficient utilization of HTGR output due to the high heat storage density and high-quality temperature output of the heat pump

Lower activation materials and magnetic fusion reactors

International Nuclear Information System (INIS)

Conn, R.W.; Bloom, E.E.; Davis, J.W.; Gold, R.E.; Little, R.; Schultz, K.R.; Smith, D.L.; Wiffen, F.W.

1984-01-01

Radioactivity in fusion reactors can be effectively controlled by materials selection. The detailed relationship between the use of a material for construction of a magnetic fusion reactor and the material's characteristics important to waste disposal, safety, and system maintainability has been studied. The quantitative levels of radioactivation are presented for many materials and alloys, including the role of impurities, and for various design alternatives. A major outcome has been the development of quantitative definitions to characterize materials based on their radioactivation properties. Another key result is a four-level classification scheme to categorize fusion reactors based on quantitative criteria for waste management, system maintenance, and safety. A recommended minimum goal for fusion reactor development is a reference reactor that (a) meets the requirements for Class C shallow land burial of waste materials, (b) permits limited hands-on maintenance outside the magnet's shield within 2 days of a shutdown, and (c) meets all requirements for engineered safety. The achievement of a fusion reactor with at least the characteristics of the reference reactor is a realistic goal. Therefore, in making design choices or in developing particular materials or alloys for fusion reactor applications, consideration must be given to both the activation characteristics of a material and its engineering practicality for a given application

Tritium permeation behavior through pyrolytic carbon in tritium production using high-temperature gas-cooled reactor for fusion reactors

Directory of Open Access Journals (Sweden)

H. Ushida

2016-12-01

Full Text Available Under tritium production method using a high-temperature gas-cooled reactor loaded Li compound, Li compound has to be coated by ceramic materials in order to suppress the spreading of tritium to the whole reactor. Pyrolytic carbon (PyC is a candidate of the coating material because of its high resistance for gas permeation. In this study, hydrogen permeation experiments using a PyC-coated isotropic graphite tube were conducted and hydrogen diffusivity, solubility and permeability were evaluated. Tritium permeation behavior through PyC-coated Li compound particles was simulated by using obtained data. Hydrogen permeation flux through PyC in a steady state is proportional to the hydrogen pressure and is larger than that through Al2O3 which is also candidate coating material. However, total tritium leak within the supposed reactor operation period through the PyC-coated Li compound particles is lower than that through the Al2O3-coated ones because the hydrogen absorption capacity in PyC is considerably larger than that in Al2O3.

Rise-to-power test in High Temperature Engineering Test Reactor. Test progress and summary of test results up to 30 MW of reactor thermal power

International Nuclear Information System (INIS)

Nakagawa, Shigeaki; Fujimoto, Nozomu; Shimakawa, Satoshi

2002-08-01

The High Temperature Engineering Test Reactor (HTTR) is a graphite moderated and gas cooled reactor with the thermal power of 30 MW and the reactor outlet coolant temperature of 850degC/950degC. Rise-to-power test in the HTTR was performed from April 23rd to June 6th in 2000 as phase 1 test up to 10 MW in the rated operation mode, from January 29th to March 1st in 2001 as phase 2 test up to 20 MW in the rated operation mode and from April 14th to June 8th in 2001 as phase 3 test up to 20 MW in the high temperature test the mechanism of the reactor outlet coolant temperature becomes 850degC at 30 MW in the rated operation mode and 950degC in the high temperature test operation mode. Phase 4 rise-to-power test to achieve the thermal reactor power of 30 MW started on October 23rd in 2001. On December 7th in 2001 it was confirmed that the thermal reactor power and the reactor outlet coolant temperature reached to 30 MW and 850degC respectively in the single loaded operation mode in which only the primary pressurized water cooler is operating. Phase 4 test was performed until March 6th in 2002. JAERI (Japan Atomic Energy Research Institute) obtained the certificate of the pre-operation test from MEXT (Ministry of Education Culture Sports Science and Technology) after all the pre-operation tests by MEXT were passed successfully with the reactor transient test at an abnormal event as a final pre-operation test. From the test results of the rise-up-power test up to 30 MW in the rated operation mode, performance of the reactor and cooling system were confirmed, and it was also confirmed that an operation of reactor facility can be performed safely. Some problems to be solved were found through the tests. By solving them, the reactor operation with the reactor outlet coolant temperature of 950degC will be achievable. (author)

Calculation of the power distribution in the fuel rods of the low power research reactor using the MCNP4C code

International Nuclear Information System (INIS)

Dawahra, S.; Khattab, K.

2011-01-01

Highlights: → The MCNP4C code was used to calculate the power distribution in 3-D geometry in the MNSR reactor. → The maximum power of the individual rod was found in the fuel ring number 2 and was found to be 105 W. → The minimum power was found in the fuel ring number 9 and was 79.9 W. → The total power in the total fuel rods was 30.9 kW. - Abstract: The Monte Carlo method, using the MCNP4C code, was used in this paper to calculate the power distribution in 3-D geometry in the fuel rods of the Syrian Miniature Neutron Source Reactor (MNSR). To normalize the MCNP4C result to the steady state nominal thermal power, the appropriate scaling factor was defined to calculate the power distribution precisely. The maximum power of the individual rod was found in the fuel ring number 2 and was found to be 105 W. The minimum power was found in the fuel ring number 9 and was 79.9 W. The total power in the total fuel rods was 30.9 kW. This result agrees very well with nominal power reported in the reactor safety analysis report which equals 30 kW. Finally, the peak power factors, which are defined as the ratios between the maximum to the average and the maximum to the minimum powers were calculated to be 1.18 and 1.31 respectively.

Gas-cooled breeder reactor safety

Energy Technology Data Exchange (ETDEWEB)

Chermanne, J.; Burgsmueller, P. [Societe Belge pour l' Industrie Nucleaire, Brussels

1981-01-15

The European Association for the Gas-cooled Breeder Reactor (G B R A), set-up in 1969 prepared between 1972 and 1974 a 1200 MWe Gas-cooled Breeder Reactor (G B R) commercial reference design G B R 4. It was then found necessary that a sound and neutral appraisal of the G B R licenseability be carried out. The Commission of the European Communities (C E C) accepted to sponsor this exercise. At the beginning of 1974, the C E C convened a group of experts to examine on a Community level, the safety documents prepared by the G B R A. A working party was set-up for that purpose. The experts examined a ''Preliminary Safety Working Document'' on which written questions and comments were presented. A ''Supplement'' containing the answers to all the questions plus a detailed fault tree and reliability analysis was then prepared. After a final study of this document and a last series of discussions with G B R A representatives, the experts concluded that on the basis of the evidence presented to the Working Party, no fundamental reasons were identified which would prevent a Gas-cooled Breeder Reactor of the kind proposed by the G B R A achieving a satisfactory safety status. Further work carried out on ultimate accident have confirmed this conclusion. One can therefore claim that the overall safety risk associated with G B R s compares favourably with that of any other reactor system.

The analysis for inventory of experimental reactor high temperature gas reactor type

International Nuclear Information System (INIS)

Sri Kuntjoro; Pande Made Udiyani

2016-01-01

Relating to the plan of the National Nuclear Energy Agency (BATAN) to operate an experimental reactor of High Temperature Gas Reactors type (RGTT), it is necessary to reactor safety analysis, especially with regard to environmental issues. Analysis of the distribution of radionuclides from the reactor into the environment in normal or abnormal operating conditions starting with the estimated reactor inventory based on the type, power, and operation of the reactor. The purpose of research is to analyze inventory terrace for Experimental Power Reactor design (RDE) high temperature gas reactor type power 10 MWt, 20 MWt and 30 MWt. Analyses were performed using ORIGEN2 computer code with high temperatures cross-section library. Calculation begins with making modifications to some parameter of cross-section library based on the core average temperature of 570 °C and continued with calculations of reactor inventory due to RDE 10 MWt reactor power. The main parameters of the reactor 10 MWt RDE used in the calculation of the main parameters of the reactor similar to the HTR-10 reactor. After the reactor inventory 10 MWt RDE obtained, a comparison with the results of previous researchers. Based upon the suitability of the results, it make the design for the reactor RDE 20MWEt and 30 MWt to obtain the main parameters of the reactor in the form of the amount of fuel in the pebble bed reactor core, height and diameter of the terrace. Based on the main parameter or reactor obtained perform of calculation to get reactor inventory for RDE 20 MWT and 30 MWT with the same methods as the method of the RDE 10 MWt calculation. The results obtained are the largest inventory of reactor RDE 10 MWt, 20 MWt and 30 MWt sequentially are to Kr group are about 1,00E+15 Bq, 1,20E+16 Bq, 1,70E+16 Bq, for group I are 6,50E+16 Bq, 1,20E+17 Bq, 1,60E+17 Bq and for groups Cs are 2,20E+16 Bq, 2,40E+16 Bq, 2,60E+16 Bq. Reactor inventory will then be used to calculate the reactor source term and it

Immobilization of carbon-14 from reactor graphite waste by use of self-sustaining reaction in the C-Al-TiO2 system

International Nuclear Information System (INIS)

Karlina, O.K.; Klimov, V.L.; Ojovan, M.I.; Pavlova, G.Yu.; Dmitriev, S.A.; Yurchenko, A.Yu.

2005-01-01

As a result of long-term neutron irradiation, the long-lived 14 C is produced in the reactor graphite. The exothermic self-sustaining reaction 3C(graphite) + 4Al + 3TiO 2 = 3TiC + 2Al 2 O 3 was proposed for processing of such waste. In doing so, the carbon, including the 14 C, is chemically bound in the stable TiC. The reaction products in the C-Al-TiO 2 system were investigated both by thermodynamic simulation and experimentally in the course of this work

Reactor incident status 1981 annual report

International Nuclear Information System (INIS)

Kiser, S.H.

1982-01-01

Reactor Incident followup action is summarized through periodic status reports. This annual report summarizes action taken or anticipated for Reactor Incidents through December 1981. Incidents for which action has been completed, have been deleted from the report. Quarterly addende will update the report by tabulating incidents for each three month period through the coming year. The report consists of a part for the P, K, and C Reactors. Each reactor part is divided into three sections: Further Technical Analysis or Followup Needed; Funding and/or Implementation Needed; and No Further Technical Analysis Anticipated

A Behavior-Preserving Translation From FBD Design to C Implementation for Reactor Protection System Software

International Nuclear Information System (INIS)

Yoo, Junbeom; Kim, Euisub; Lee, Jangsoo

2013-01-01

Software safety for nuclear reactor protection systems (RPSs) is the most important requirement for the obtainment of permission for operation and export from government authorities, which is why it should be managed with well-experienced software development processes. The RPS software is typically modeled with function block diagrams (FBDs) in the design phase, and then mechanically translated into C programs in the implementation phase, which is finally compiled into executable machine codes and loaded on RPS hardware - PLC (Programmable Logic Controller). Whereas C Compilers are fully-verified COTS (Commercial Off-The-Shelf) software, translators from FBDs to C programs are provided by PLC vendors. Long-term experience, experiments and simulations have validated their correctness and function safety. This paper proposes a behavior-preserving translation from FBD design to C implementation for RPS software. It includes two sets of translation algorithms and rules as well as a prototype translator. We used an example of RPS software in a Korean nuclear power plant to demonstrate the correctness and effectiveness of the proposed translation

A Behavior-Preserving Translation From FBD Design to C Implementation for Reactor Protection System Software

Energy Technology Data Exchange (ETDEWEB)

Yoo, Junbeom; Kim, Euisub [Konkuk Univ., Seoul (Korea, Republic of); Lee, Jangsoo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-08-15

Software safety for nuclear reactor protection systems (RPSs) is the most important requirement for the obtainment of permission for operation and export from government authorities, which is why it should be managed with well-experienced software development processes. The RPS software is typically modeled with function block diagrams (FBDs) in the design phase, and then mechanically translated into C programs in the implementation phase, which is finally compiled into executable machine codes and loaded on RPS hardware - PLC (Programmable Logic Controller). Whereas C Compilers are fully-verified COTS (Commercial Off-The-Shelf) software, translators from FBDs to C programs are provided by PLC vendors. Long-term experience, experiments and simulations have validated their correctness and function safety. This paper proposes a behavior-preserving translation from FBD design to C implementation for RPS software. It includes two sets of translation algorithms and rules as well as a prototype translator. We used an example of RPS software in a Korean nuclear power plant to demonstrate the correctness and effectiveness of the proposed translation.

A Preliminary Analysis of Reactor Performance Test (LOEP) for a Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyeonil; Park, Su-Ki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

The final phase of commissioning is reactor performance test, which is to prove the integrated performance and safety of the research reactor at full power with fuel loaded such as neutron power calibration, Control Absorber Rod/Second Shutdown Rod drop time, InC function test, Criticality, Rod worth, Core heat removal with natural mechanism, and so forth. The last test will be safety-related one to assure the result of the safety analysis of the research reactor is marginal enough to be sure about the nuclear safety by showing the reactor satisfies the acceptance criteria of the safety functions such as for reactivity control, maintenance of auxiliaries, reactor pool water inventory control, core heat removal, and confinement isolation. After all, the fuel integrity will be ensured by verifying there is no meaningful change in the radiation levels. To confirm the performance of safety equipment, loss of normal electric power (LOEP), possibly categorized as Anticipated Operational Occurrence (AOO), is selected as a key experiment to figure out how safe the research reactor is before turning over the research reactor to the owner. This paper presents a preliminary analysis of the reactor performance test (LOEP) for a research reactor. The results showed how different the transient between conservative estimate and best estimate will look. Preliminary analyses have shown all probable thermal-hydraulic transient behavior of importance as to opening of flap valve, minimum critical heat flux ratio, the change of flow direction, and important values of thermal-hydraulic parameters.

Nuclear reactor monitoring device

International Nuclear Information System (INIS)

Mihashi, Ishi; Honma, Hitoshi.

1993-01-01

The monitoring device of the present invention comprises a reactor core/reactor system data measuring and controlling device, a radioactivity concentration calculation device for activated coolants for calculating a radioactivity concentration of activated coolants in a main steam and reactor water by using an appropriate physical model, a radioactivity concentration correlation and comparison device for activated coolants for comparing correlationship with a radiation dose and an abnormality alarm device. Since radioactivity of activated primary coolants is monitored at each of positions in the reactor system and occurrence of leakage and the amount thereof from a primary circuit to a secondary circuit is monitored if the reactor has secondary circuit, integrity of the reactor system can be ensured and an abnormality can be detected rapidly. Further, radioactivity concentration of activated primary circuit coolants, represented by 16 N or 15 C, is always monitored at each of positions of PWR primary circuits. When a heat transfer pipe is ruptured in a steam generator, leakage of primary circuit coolants is detected rapidly, as well as the amount of the leakage can be informed. (N.H.)

Digital control of research reactors

International Nuclear Information System (INIS)

Crump, J.C. III.; Richards, W.J.; Heidel, C.C.

1991-01-01

Research reactors provide an important service for the nuclear industry. Developments and innovations used for research reactors can be later applied to larger power reactors. Their relatively inexpensive cost allows research reactors to be an excellent testing ground for the reactors of tomorrow. One area of current interest is digital control of research reactor systems. Digital control systems offer the benefits of implementation and superior system response over their analog counterparts. At McClellan Air Force Base in Sacramento, California, the Stationary Neutron Radiography System (SNRS) uses a 1,000-kW TRIGA reactor for neutron radiography and other nuclear research missions. The neutron radiography beams generated by the reactor are used to detect corrosion in aircraft structures. While the use of the reactor to inspect intact F-111 wings is in itself noteworthy, there is another area in which the facility has applied new technology: the instrumentation and control system (ICS). The ICS developed by General Atomics (GA) contains several new and significant items: (a) the ability to servocontrol on three rods, (b) the ability to produce a square wave, and (c) the use of a software configurator to tune parameters affected by the actual reactor core dynamics. These items will probably be present in most, if not all, future research reactors. They were developed with increased control and overall usefulness of the reactor in mind

Medium temperature carbon dioxide gas turbine reactor

International Nuclear Information System (INIS)

Kato, Yasuyoshi; Nitawaki, Takeshi; Muto, Yasushi

2004-01-01

A carbon dioxide (CO 2 ) gas turbine reactor with a partial pre-cooling cycle attains comparable cycle efficiencies of 45.8% at medium temperature of 650 deg. C and pressure of 7 MPa with a typical helium (He) gas turbine reactor of GT-MHR (47.7%) at high temperature of 850 deg. C. This higher efficiency is ascribed to: reduced compression work around the critical point of CO 2 ; and consideration of variation in CO 2 specific heat at constant pressure, C p , with pressure and temperature into cycle configuration. Lowering temperature to 650 deg. C provides flexibility in choosing materials and eases maintenance through the lower diffusion leak rate of fission products from coated particle fuel by about two orders of magnitude. At medium temperature of 650 deg. C, less expensive corrosion resistant materials such as type 316 stainless steel are applicable and their performance in CO 2 have been proven during extensive operation in AGRs. In the previous study, the CO 2 cycle gas turbomachinery weight was estimated to be about one-fifth compared with He cycles. The proposed medium temperature CO 2 gas turbine reactor is expected to be an alternative solution to current high-temperature He gas turbine reactors

The in-core experimental program at the MIT Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Kohse, G.E.; Hu, L-W., E-mail: kohse@mit.edu [Massachusetts Inst. of Technology, Nuclear Reactor Lab., Cambridge, Massachusetts (United States)

2014-07-01

This paper describes the program of in-core experiments at the Massachusetts Institute of Technology Research Reactor (MITR), a 6 MW research reactor. The MITR has a neutron flux and spectrum similar to those in water-cooled power reactors and therefore provides a useful test environment for materials and fuels research. In-core facilities include: a water loop operating at pressurized water or boiling water reactor conditions, an inert gas irradiation facility operating at temperature up to 850 {sup o}C and special purpose facilities including fuel irradiation experiments. Recent and ongoing tests include: water loop investigations of corrosion and thermal and mechanical property evolution of SiC/SiC composites for fuel cladding, irradiation of advanced materials and in-core sensors at elevated temperatures, irradiation in molten fluoride salt at 700 {sup o}C of metal alloy, graphite and composite materials for power reactor applications and instrumented irradiations of metal-bonded hydride fuel. (author)

Reactor Simulations for Safeguards with the MCNP Utility for Reactor Evolution Code

International Nuclear Information System (INIS)

Shiba, T.; Fallot, M.

2015-01-01

To tackle nuclear material proliferation, we conducted several proliferation scenarios using the MURE (MCNP Utility for Reactor Evolution) code. The MURE code, developed by CNRS laboratories, is a precision, open-source code written in C++ that automates the preparation and computation of successive MCNP (Monte Carlo N-Particle) calculations and solves the Bateman equations in between, for burnup or thermal-hydraulics purposes. In addition, MURE has been completed recently with a module for the CHaracterization of Radioactive Sources, called CHARS, which computes the emitted gamma, beta and alpha rays associated to any fuel composition. Reactor simulations could allow knowing how plutonium or other material generation evolves inside reactors in terms of time and amount. The MURE code is appropriate for this purpose and can also provide knowledge on associated particle emissions. Using MURE, we have both developed a cell simulation of a typical CANDU reactor and a detailed model of light water PWR core, which could be used to analyze the composition of fuel assemblies as a function of time or burnup. MURE is also able to provide, thanks to its extension MURE-CHARTS, the emitted gamma rays from fuel assemblies unloaded from the core at any burnup. Diversion cases of Generation IV reactors have been also developed; a design of Very High Temperature Reactor (a Pebble Bed Reactor (PBR), loaded with UOx, PuOx and ThUOx fuels), and a Na-cooled Fast Breeder Reactor (FBR) (with depleted Uranium or Minor Actinides in the blanket). The loading of Protected Plutonium Production (P3) in the FBR was simulated. The simulations of various reactor designs taking into account reactor physics constraints may bring valuable information to inspectors. At this symposium, we propose to show the results of these reactor simulations as examples of the potentiality of reactor simulations for safeguards. (author)

Development of Digital MMIS for Research Reactors: Graded Approaches

Energy Technology Data Exchange (ETDEWEB)

Khalil ur, Rahman; Shin, Jin Soo; Heo, Gyun Young [Kyunghee University, Yongin (Korea, Republic of); Son, Han Seong [Joongbu University, Geumsan (Korea, Republic of); Kim, Young Ki; Park, Jae Kwan; Seo, Sang Mun; Kim, Yong Jun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-05-15

Though research reactors are small in size yet they are important in terms of industrial applications and R and D, educational purposes. Keeping the eye on its importance, Korean government has intention to upgrade and extend this industry. Presently, Korea is operating only HANARO at Korea Atomic Energy Research Institute (KAERI) and AGN-201K at Kyung Hee University (KHU), which are not sufficient to meet the current requirements of research and education. In addition, we need self-sufficiency in design and selfreliance in design and operation, as we are installing research reactors in domestic as well as foreign territories for instance Jordan. Based on these demands, KAERI and universities initiated a 5 year research project since December 2011 collaboratly, for the deep study of reactor core, thermal hydraulics, materials and instrumentation and control (I and C). This particular study is being carried out to develop highly reliable advanced digital I and C systems using a grading approach. It is worth mentioning that next generation research reactor should be equipped with advance state of the art digital I and C for safe and reliable operation and impermeable cyber security system that is needed to be devised. Moreover, human error is one of important area which should be linked with I and C in terms of Man Machine Interface System (MMIS) and development of I and C should cover human factor engineering. Presently, the digital I and C and MMIS are well developed for commercial power stations whereas such level of development does not exist for research reactors in Korea. Since the functional and safety requirements of research reactors are not so strict as commercial power plants, the design of digital I and C systems for research reactors seems to be graded based on the stringency of regulatory requirements. This paper was motivated for the introduction of those missions, so it is going to describe the general overview of digital I and C systems, the graded

Development of Digital MMIS for Research Reactors: Graded Approaches

International Nuclear Information System (INIS)

Khalil ur, Rahman; Shin, Jin Soo; Heo, Gyun Young; Son, Han Seong; Kim, Young Ki; Park, Jae Kwan; Seo, Sang Mun; Kim, Yong Jun

2012-01-01

Though research reactors are small in size yet they are important in terms of industrial applications and R and D, educational purposes. Keeping the eye on its importance, Korean government has intention to upgrade and extend this industry. Presently, Korea is operating only HANARO at Korea Atomic Energy Research Institute (KAERI) and AGN-201K at Kyung Hee University (KHU), which are not sufficient to meet the current requirements of research and education. In addition, we need self-sufficiency in design and selfreliance in design and operation, as we are installing research reactors in domestic as well as foreign territories for instance Jordan. Based on these demands, KAERI and universities initiated a 5 year research project since December 2011 collaboratly, for the deep study of reactor core, thermal hydraulics, materials and instrumentation and control (I and C). This particular study is being carried out to develop highly reliable advanced digital I and C systems using a grading approach. It is worth mentioning that next generation research reactor should be equipped with advance state of the art digital I and C for safe and reliable operation and impermeable cyber security system that is needed to be devised. Moreover, human error is one of important area which should be linked with I and C in terms of Man Machine Interface System (MMIS) and development of I and C should cover human factor engineering. Presently, the digital I and C and MMIS are well developed for commercial power stations whereas such level of development does not exist for research reactors in Korea. Since the functional and safety requirements of research reactors are not so strict as commercial power plants, the design of digital I and C systems for research reactors seems to be graded based on the stringency of regulatory requirements. This paper was motivated for the introduction of those missions, so it is going to describe the general overview of digital I and C systems, the graded

The in-reactor deformation of the PCA alloy

International Nuclear Information System (INIS)

Puigh, R.J.

1986-04-01

The swelling and in-reactor creep behaviors of the PCA alloy have been determined from the irradiation of pressurized tube specimens in the FFTF reactor. These data have been obtained to a peak neutron fluence corresponding to approximately 80 dpa in the FFTF reactor for irradiation temperatures between 400 and 750 0 C. Diametral measurements performed on the unstressed specimens indicate the possible onset of swelling in the PCA alloy for irradiation temperatures between 400 and 550 0 C and at a neutron fluence corresponding to ∼50 dpa. The creep data suggest a non-linear fluence dependence and linear stress dependence (for hoop stresses less than 100 MPa) which is consistent with the in-reactor creep behavior of many cold worked austenitic stainless steels. These PCA creep data are compared to available 316 SS in-reactor creep data. The in-reactor creep strains for PCA are significantly less than observed in 20% cold worked 316 SS over the temperature ranges and fluences investigated

Compact reactor/ORC power source

International Nuclear Information System (INIS)

Meier, K.L.; Kirchner, W.L.; Willcutt, G.J.

1986-01-01

A compact power source that combines an organic Rankine Cycle (ORC) electric generator with a nuclear reactor heat source is being designed and fabricated. Incorporating existing ORC technology with proven reactor technology, the compact reactor/ORC power source offers high reliability while minimizing the need for component development. Thermal power at 125 kWt is removed from the coated particle fueled, graphite moderated reactor by heat pipes operating at 500 0 C. Outside the reactor vessel and connected to the heat pipes are vaporizers in which the toluene ORC working fluid is heated to 370 0 C. In the turbine-alternator-pump (TAP) combined-rotating unit, the thermal energy of the toluene is converted to 25 kWe of electric power. Lumped parameter systems analyses combined with a finite element thermal analysis have aided in the power source design. The analyses have provided assurance of reliable multiyear normal operation as well as full power operation with upset conditions, such as failed heat pipes and inoperative ORC vaporizers. Because of inherent high reliability, long life, and insensitivity to upset conditions, this power source is especially suited for use in remote, inaccessible locations where fuel delivery and maintenance costs are high. 10 refs

Some general remarks concerning the experimental devices and means for flux measurements used in the research reactors of the C.E.A

International Nuclear Information System (INIS)

Rossillon, F.; Chauvez, C.

1964-01-01

First, the authors define the operation and organisation lay-out of the research reactors. This out lay is then used as a basis for an examination of the conception, realisation and exploitation of irradiation devices. They then analyse the different operations carried out in placing an irradiation device in the reactor. They point out that the time necessary for decision of construction, conception, for material provision, for construction, out-of-pile tests and security examination is in general longer than the irradiation time. To minimize this time they advise a closer collaboration between the personnel of the experimentation laboratory and the reactor personnel for the conception of the design. They think it would be preferable to construct the prototypes in the research centre and leave the fabrication of small series to the industry. The methods used for the in-pile operation of the device are also indicated. Considering the evolution of the construction techniques they mention that the requirements for the irradiation conditions are put higher and higher (reactor stability and homogeneity). Also described are the performances of the main irradiation devices in operation in research reactor in the C.E.A. (authors) [fr

Analyses and results from standard surveillance programmes of WWER 440/V-213C reactor pressure vessels

Energy Technology Data Exchange (ETDEWEB)

Falcnik, M; Brumovsky, M; Pav, T [Czech Nuclear Society, Prague (Czech Republic)

1994-12-31

In Czech and Slovak republics, six units of WWER 440/C type reactors are monitored by surveillance specimens programmes; the specimens are determined for static tensile testing, impact notch toughness testing and fracture toughness evaluation. Results of mechanical properties of these specimens after irradiation in intervals between 1 and 5 years of operation, are summarized and discussed with respect to the effect of individual heats and welded joints, radiation embrittlement, and annealing recovery. (authors). 3 refs., 11 figs., 2 tabs.

Simulación con el código MCNP del reactor nuclear RP-10 en su configuración #14, BOC

OpenAIRE

Lázaro, Gerardo; Parreño, Fernando

2001-01-01

Se presenta los resultados de exceso de reactividad del núcleo del reactor RP-10 en su configuración 14. Este exceso de reactividad ha sido calculado con MCNP4B con un modelo que describe en detalle las características de los elementos combustibles normales y de control, así como de cada elemento que constituye la configuración de trabajo #14. Este modelo fue previamente utilizado en el reactor RP-0 y ha sido aplicado en la configuración de arranque para el cálculo del exceso de reactividad y...

Calculation of photon dose for Dalat research reactor in case of loss of reactor tank water

International Nuclear Information System (INIS)

Le Vinh Vinh; Huynh Ton Nghiem; Nguyen Kien Cuong

2007-01-01

Photon sources of actinides and fission products were estimated by ORIGEN2 code with the modified cross-section library for Dalat research reactor (DRR) using new cross-section generated by WIMS-ANL code. Photon sources of reactor tank water calculated from the experimental data. MCNP4C2 with available non-analog Monte Carlo model and ANSI/ANL-6.1.1-1977 flux-to-dose factors were used for dose estimation. The agreement between calculation results and those of measurements showed that the methods and models used to get photon sources and dose were acceptable. In case the reactor water totally leaks out from the reactor tank, the calculated dose is very high at the top of reactor tank while still low in control room. In the reactor hall, the operation staffs can access for emergency works but with time limits. (author)

Analysis of the interim safe storage of reactors at the Hanford site

International Nuclear Information System (INIS)

Wang Hailiang

2014-01-01

The nine production reactors, i.e. B, C, D, DR, F, H, KE, KW and N, at the Hanford site are all water-cooled and graphite-moderated reactors with natural uranium fuel. In 1993, the U.S. Department of Energy (DOE) decided to put eight production reactors (except for B) into Interim Safe Storage (ISS) for 75 years followed by deferred one-piece removal. Reactor B will remain as a national historical landmark. By the end of 2013, six reactors C, F, D, DR, H and N had been successfully put into the ISS. Reactors KE and KW will be put into the ISS in the coming years. Taking reactor C as an example, this paper mainly talks about how to put the production reactors in the Interim Safe Storage, e.g. how to make site preparation, how to construct the safe storage enclosure (SSE) and how to perform surveillance and maintenance during the ISS period, etc. (authors)

Core design concepts for high performance light water reactors

International Nuclear Information System (INIS)

Schulenberg, T.; Starflinger, J.

2007-01-01

Light water reactors operated under supercritical pressure conditions have been selected as one of the promising future reactor concepts to be studied by the Generation IV International Forum. Whereas the steam cycle of such reactors can be derived from modern fossil fired power plants, the reactor itself, and in particular the reactor core, still need to be developed. Different core design concepts shall be described here to outline the strategy. A first option for near future applications is a pressurized water reactor with 380 .deg. C core exit temperature, having a closed primary loop and achieving 2% pts. higher net efficiency and 24% higher specific turbine power than latest pressurized water reactors. More efficiency and turbine power can be gained from core exit temperatures around 500 .deg. C, which require a multi step heat up process in the core with intermediate coolant mixing, achieving up to 44% net efficiency. The paper summarizes different core and assembly design approaches which have been studied recently for such High Performance Light Water Reactors

Principle of human system interface (HSI) design for new reactor console of PUSPATI TRIGA Reactor (RTP)

International Nuclear Information System (INIS)

Zareen Khan Abdul Jalil Khan; Ridzuan Abdul Mutalib; Mohd Idris Taib; Mohd Khairulezwan Abdul Manan; Nurfarhana Ayuni Joha; Mohd Sabri Minhat; Izhar Abu Hussin

2013-01-01

Full-text: This paper will describe the principle of human system interface design for new reactor console in control room at TRIGA reactor facility. In order to support these human system interface challenges in digital reactor console. Software-based instrumentation and control (I and C) system for new reactor console could lead to new human machine integration. The proposed of Human System Interface (HSI) which included the large display panels which shows reactor status, compact and computer-based workstations for monitoring, control and protection function. The proposed Human System Interface (HIS) has been evaluated using various human factor engineering. It can be concluded that the Human System Interface (HIS) is designed as to address the safety related computer controlled system. (author)

Trench reactor: an overview

International Nuclear Information System (INIS)

Spinrad, B.I.; Rohach, A.F.; Razzaque, M.M.; Sankoorikal, J.T.; Schmidt, R.S.; Lofshult, J.; Ramin, T.; Sokmen, N.; Lin, L.C.

1988-01-01

Recent fast, sodium-cooled reactor designs reflect new conditions. In nuclear energy these conditions are (a) emphasis on maintainability and operability, (b) design for more transparent safety, and (c) a surplus of uranium and enrichment availability that eases concerns about light water reactor fueling costs. In utility practice the demand is for less capital exposure, short construction time, smaller new unit sizes, and low capital cost. The PRISM, SAFR, and integral fast reactor (IFR) concepts are responses to these conditions. Fast reactors will not soon be deployed commercially, so more radical designs can be considered. The trench reactor is the product of such thinking. Its concepts are intended as contributions to the literature, which may be picked up by one of the existing programs or used in a new experimental project. The trench reactor is a thin-slab, pool-type reactor operated at very low power density and- for sodium-modest temperature. The thin slab is repeated in the sodium tank and the reactor core. The low power density permits a longer than conventional core height and a large-diameter fuel pin. Control is by borated steel slabs that can be lowered between the core and lateral sodium reflector. Shutdown is by semaphore slabs that can be swung into place just outside the control slabs. The paper presents major characteristics of the trench reactor that have been changed since the last report

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

International Nuclear Information System (INIS)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO 2 ) and lithium silicate (Li 2 SiO 3 ) by the reaction: Li 6 + n → 4 He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100 0 C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T 2 ), while in laboratory extractions (300-1300 0 C), the tritium appeared primarily in the condensible form (HTO and T 2 O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H 2 O, CO 2 , CO, O 2 , H 2 , NO, SO 2 , SiF 4 and traces of hydrocarbons

Rapid preparation of high electrochemical performance LiFePO4/C composite cathode material with an ultrasonic-intensified micro-impinging jetting reactor.

Science.gov (United States)

Dong, Bin; Huang, Xiani; Yang, Xiaogang; Li, Guang; Xia, Lan; Chen, George

2017-11-01

A joint chemical reactor system referred to as an ultrasonic-intensified micro-impinging jetting reactor (UIJR), which possesses the feature of fast micro-mixing, was proposed and has been employed for rapid preparation of FePO 4 particles that are amalgamated by nanoscale primary crystals. As one of the important precursors for the fabrication of lithium iron phosphate cathode, the properties of FePO 4 nano particles significantly affect the performance of the lithium iron phosphate cathode. Thus, the effects of joint use of impinging stream and ultrasonic irradiation on the formation of mesoporous structure of FePO 4 nano precursor particles and the electrochemical properties of amalgamated LiFePO 4 /C have been investigated. Additionally, the effects of the reactant concentration (C=0.5, 1.0 and 1.5molL -1 ), and volumetric flow rate (V=17.15, 51.44, and 85.74mLmin -1 ) on synthesis of FePO 4 ·2H 2 O nucleus have been studied when the impinging jetting reactor (IJR) and UIJR are to operate in nonsubmerged mode. It was affirmed from the experiments that the FePO 4 nano precursor particles prepared using UIJR have well-formed mesoporous structures with the primary crystal size of 44.6nm, an average pore size of 15.2nm, and a specific surface area of 134.54m 2 g -1 when the reactant concentration and volumetric flow rate are 1.0molL -1 and 85.74mLmin -1 respectively. The amalgamated LiFePO 4 /C composites can deliver good electrochemical performance with discharge capacities of 156.7mAhg -1 at 0.1C, and exhibit 138.0mAhg -1 after 100 cycles at 0.5C, which is 95.3% of the initial discharge capacity. Copyright © 2017. Published by Elsevier B.V.

Implementation of digital control and protection systems of China advanced research reactor

International Nuclear Information System (INIS)

Zeng Hai; Jin Huajin; Xu Qiguo; Zhang Mingkui

2005-01-01

China Advanced Research Reactor (CARR), a reactor of the 21st century with high performance is being constructed in China. The requirements of reliability and stability on the control and protection (c and p) system are the main points raised. Especially, with the development of digital technology, the c and p system of CARR is demanded to match the trend of digitization in the field of reactor control. The c and p system, including reactor protection system, reactor monitoring and control system, reactor power regulating system, and the mitigation system for ATWS (Anticipate Transient Without Scram), adopts digital technology, and the digital display screen will replace the analog panels in the main control room. The c and p system of CARR adopts redundant technology with 2 or 3 redundant channels to improve the system reliability. The 10/100 Mbps self-adaptive redundant optic fiber industry Ethernet ring network is used to interlink operator workstations, supervisor workstation, and I/O control stations. Commercial grade equipment with mature experience in industrial application are applied to the c and p system of CARR, which have high reliability, good interchangeability, and is easily purchased, the software-developing tools fully match the international industry standards. The realization of digital c and p system of CARR will promote the progress of digital control technology for reactors in China, and certainly become a technical basic platform for developing informational and intelligent reactors in China. (authors)

International topical meeting. Research Reactor Fuel Management (RRFM) and meeting of the International Group on Reactor Research (IGORR)

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

Nuclear research and test reactors have been in operation for over 60 years, over 270 research reactors are currently operating in more than 50 countries. This meeting is dedicated to different aspects of research reactor fuels: new fuels for new reactors, the conversion to low enriched uranium fuels, spent fuel management and computational tools for core simulation. About 80 contributions are reported in this document, they are organized into 7 sessions: 1) international topics and overview on new projects and fuel, 2) new projects and upgrades, 3) fuel development, 4) optimisation and research reactor utilisation, 5) innovative methods in research reactors physics, 6) safety, operation and research reactor conversion, 7) fuel back-end management, and a poster session. Experience from Australian, Romanian, Libyan, Syrian, Vietnamese, South-African and Ghana research reactors are reported among other things. The Russian program for research reactor spent fuel management is described and the status of the American-driven program for the conversion to low enriched uranium fuels is presented. (A.C.)

Methodology Development for SiC Sensor Signal Modelling in the Nuclear Reactor Radiation Environments

International Nuclear Information System (INIS)

Cetnar, J.; Krolikowski, I.P.

2013-06-01

This paper deals with SiC detector simulation methodology for signal formation by neutrons and induced secondary radiation as well as its inverse interpretation. The primary goal is to achieve the SiC capability of simultaneous spectroscopic measurements of neutrons and gamma-rays for which an appropriate methodology of the detector signal modelling and its interpretation must be adopted. The process of detector simulation is divided into two basically separate but actually interconnected sections. The first one is the forward simulation of detector signal formation in the field of the primary neutron and secondary radiations, whereas the second one is the inverse problem of finding a representation of the primary radiation, based on the measured detector signals. The applied methodology under development is based on the Monte Carlo description of radiation transport and analysis of the reactor physics. The methodology of SiC detector signal interpretation will be based on the existing experience in neutron metrology developed in the past for various neutron and gamma-ray detection systems. Since the novel sensors based on SiC are characterised by a new structure, yet to be finally designed, the methodology for particle spectroscopic fluence measurement must be developed while giving a productive feed back to the designing process of SiC sensor, in order to arrive at the best possible design. (authors)

Production of ZrC Matrix for Use in Gas Fast Reactor Composite Fuels

International Nuclear Information System (INIS)

Vasudevamurthy, Gokul; Knight, Travis W.; Roberts, Elwyn; Adams, Thad

2007-01-01

Zirconium carbide is being considered as a candidate for inert matrix material in composite nuclear fuel for Gas fast reactors due to its favorable characteristics. ZrC can be produced by the direct reaction of pure zirconium and graphite powders. Such a reaction is exothermic in nature. The reaction is self sustaining once initial ignition has been achieved. The heat released during the reaction is high enough to complete the reaction and achieve partial sintering without any external pressure applied. External heat source is required to achieve ignition of the reactants and maintain the temperature close to the adiabatic temperature to achieve higher levels of sintering. External pressure is also a driving force for sintering. In the experiments described, cylindrical compacts of ZrC were produced by direct combustion reaction. External induction heating combined with varying amounts of external applied pressure was employed to achieve varying degrees of density/porosity. The effect of reactant particle size on the product characteristics was also studied. The samples were characterized for density/porosity, composition and microstructure. (authors)

Adaptation of phytoplankton-degrading microbial communities to thermal reactor effluent in a new cooling reservoir

International Nuclear Information System (INIS)

Schoenberg, S.A.; Benner, R.; Sobecky, P.; Hodson, R.E.

1988-01-01

In water column and sediment inocula from a nuclear reactor cooling reservoir, natural phytoplankton substrate labeled with 14 C was used to determine aerobic and anaerobic mineralization rates for a range of temperatures (25, 40, 55, and 70 0 C) expected during reactor operation. For experiments that were begun during reactor shutdown, aerobic decomposition occurred at temperatures of 0 C. After two months of reactor operation, aerobic rates increased substantially at 55 and 70 0 C, although maximum rates were observed at temperatures of ≤ 40 0 C. The temperature range for which maximum anaerobic mineralization (i.e., the sum of CH 4 and CO 2 ) was observed was 25 to 40 0 C when the reactor was off, expanding to 25 to 55 0 C during reactor operation. Increased rates of 55 0 C, but not 70 0 C, correlated with an increase in the ratio of cumulative methane to carbon dioxide produced over 21 days. When reduced reactor power lowered the maximum temperature of the reservoir to 42 0 C, aerobic decomposition at 70 0 C was negligible, but remained substantial at 55 0 C. Selection for thermophilic decomposers occurred rapidly in this system in both aerobic and anaerobic communities and did not require prolonged exposure to elevated temperatures

Instrumentation and control strategies for an integral pressurized water reactor

Directory of Open Access Journals (Sweden)

Belle R. Upadhyaya

2015-03-01

Full Text Available Several vendors have recently been actively pursuing the development of integral pressurized water reactors (iPWRs that range in power levels from small to large reactors. Integral reactors have the features of minimum vessel penetrations, passive heat removal after reactor shutdown, and modular construction that allow fast plant integration and a secure fuel cycle. The features of an integral reactor limit the options for placing control and safety system instruments. The development of instrumentation and control (I&C strategies for a large 1,000 MWe iPWR is described. Reactor system modeling—which includes reactor core dynamics, primary heat exchanger, and the steam flashing drum—is an important part of I&C development and validation, and thereby consolidates the overall implementation for a large iPWR. The results of simulation models, control development, and instrumentation features illustrate the systematic approach that is applicable to integral light water reactors.

Comparative Analysis of Carbon Plasma in Arc and RF Reactors

International Nuclear Information System (INIS)

Todorovic-Markovic, B.; Markovic, Z.; Mohai, I.; Szepvolgyi, J.

2004-01-01

Results on studies of molecular spectra emitted in the initial stages of fullerene formation during the processing of graphite powder in induction RF reactor and evaporation of graphite electrodes in arc reactor are presented in this paper. It was found that C2 radicals were dominant molecular species in both plasmas. C2 radicals have an important role in the process of fullerene synthesis. The rotational-vibrational temperatures of C2 and CN species were calculated by fitting the experimental spectra to the simulated ones. The results of optical emission study of C2 radicals generated in carbon arc plasma have shown that rotational temperature of C2 species depends on carbon concentration and current intensity significantly. The optical emission study of induction RF plasma and SEM analysis of graphite powder before and after plasma treatment have shown that evaporation of the processed graphite powder depends on feed rate and composition of gas phase significantly. Based on the obtained results, it was concluded that in the plasma region CN radicals could be formed by the reaction of C2 species with atomic nitrogen at smaller loads. At larger feed rate of graphite powder, CN species were produced by surface reaction of the hot carbon particles with nitrogen atoms. The presence of nitrogen in induction RF plasma reduces the fullerene yield significantly. The fullerene yield obtained in two different reactors was: 13% in arc reactor and 4.1% in induction RF reactor. However, the fullerene production rate was higher in induction RF reactor-6.4 g/h versus 1.7 g/h in arc reactor

Permanent seal ring for a nuclear reactor cavity

International Nuclear Information System (INIS)

Hankinson, M.F.; Marshall, J.R.

1988-01-01

A nuclear reactor containment arrangement is described including: a. a reactor vessel which thermally expands and contracts during cyclic operation of the reactor and which has a peripheral wall; b. a containment wall spaced apart from and surrounding the peripheral wall of the reactor vessel and defining an annular thermal expansion gap therebetween for accommodating thermal expansion; and c. an annular ring seal which sealingly engages and is affixed to and extends between the peripheral wall of the reactor vessel and the containment wall

Isothermal temperature reactivity coefficient measurement in TRIGA reactor

International Nuclear Information System (INIS)

Zagar, T.; Ravnik, M.; Trkov, A.

2002-01-01

Direct measurement of an isothermal temperature reactivity coefficient at room temperatures in TRIGA Mark II research reactor at Jozef Stefan Institute in Ljubljana is presented. Temperature reactivity coefficient was measured in the temperature range between 15 o C and 25 o C. All reactivity measurements were performed at almost zero reactor power to reduce or completely eliminate nuclear heating. Slow and steady temperature decrease was controlled using the reactor tank cooling system. In this way the temperatures of fuel, of moderator and of coolant were kept in equilibrium throughout the measurements. It was found out that TRIGA reactor core loaded with standard fuel elements with stainless steel cladding has small positive isothermal temperature reactivity coefficient in this temperature range.(author)

Tritium resources available for fusion reactors

Science.gov (United States)

Kovari, M.; Coleman, M.; Cristescu, I.; Smith, R.

2018-02-01

The tritium required for ITER will be supplied from the CANDU production in Ontario, but while Ontario may be able to supply 8 kg for a DEMO fusion reactor in the mid-2050s, it will not be able to provide 10 kg at any realistic starting time. The tritium required to start DEMO will depend on advances in plasma fuelling efficiency, burnup fraction, and tritium processing technology. It is in theory possible to start up a fusion reactor with little or no tritium, but at an estimated cost of 2 billion per kilogram of tritium saved, it is not economically sensible. Some heavy water reactor tritium production scenarios with varying degrees of optimism are presented, with the assumption that only Canada, the Republic of Korea, and Romania make tritium available to the fusion community. Results for the tritium available for DEMO in 2055 range from zero to 30 kg. CANDU and similar heavy water reactors could in theory generate additional tritium in a number of ways: (a) adjuster rods containing lithium could be used, giving 0.13 kg per year per reactor; (b) a fuel bundle with a burnable absorber has been designed for CANDU reactors, which might be adapted for tritium production; (c) tritium production could be increased by 0.05 kg per year per reactor by doping the moderator with lithium-6. If a fusion reactor is started up around 2055, governments in Canada, Argentina, China, India, South Korea and Romania will have the opportunity in the years leading up to that to take appropriate steps: (a) build, refurbish or upgrade tritium extraction facilities; (b) extend the lives of heavy water reactors, or build new ones; (c) reduce tritium sales; (d) boost tritium production in the remaining heavy water reactors. All of the alternative production methods considered have serious economic and regulatory drawbacks, and the risk of diversion of tritium or lithium-6 would also be a major concern. There are likely to be serious problems with supplying tritium for future

Study on thermodynamic cycle of high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Qu Xinhe; Yang Xiaoyong; Wang Jie

2017-01-01

The development trend of the (very) High temperature gas-cooled reactor is to gradually increase the reactor outlet temperature. The different power conversion units are required at the different reactor outlet temperature. In this paper, for the helium turbine direct cycle and the combined cycle of the power conversion unit of the High temperature gas-cooled reactor, the mathematic models are established, and three cycle plans are designed. The helium turbine direct cycle is a Brayton cycle with recuperator, precooler and intercooler. In the combined cycle plan 1, the topping cycle is a simple Brayton cycle without recuperator, precooler and intercooler, and the bottoming cycle is based on the steam parameters (540deg, 6 MPa) recommended by Siemens. In the combined cycle plan 2, the topping cycle also is a simple Brayton cycle, and the bottoming cycle which is a Rankine cycle with reheating cycle is based on the steam parameters of conventional subcritical thermal power generation (540degC, 18 MPa). The optimization results showed that the cycle efficiency of the combined cycle plan 2 is the highest, the second is the helium turbine direct cycle, and the combined cycle plan 2 is the lowest. When the reactor outlet temperature is 900degC and the pressure ratio is 2.02, the cycle efficiency of the combined cycle plan 2 can reach 49.7%. The helium turbine direct cycle has a reactor inlet temperature above 500degC due to the regenerating cycle, so it requires a cooling circuit for the internal wall of the reactor pressure vessel. When the reactor outlet temperature increases, the increase of the pressure ratio required by the helium turbine direct cycle increases may bring some difficulties to the design and manufacture of the magnetic bearings. For the combined cycle, the reactor inlet temperature can be controlled below than 370degC, so the reactor pressure vessel can use SA533 steel without cooling the internal wall of the reactor pressure vessel. The pressure

Design and analysis on super-critical water cooled power reactors

International Nuclear Information System (INIS)

Ishiwatari, Yuki

2005-01-01

The Super-Critical Water Cooled Power Reactors (SCPR) is cooled by 25 MPa supercritical water of 280degC at reactor inlet and greater than 500degC at reactor outlet and directly connected with turbine/generators with high energy conversion efficiency. This corresponds to the deletion of recirculation system and steam-water separation system of BWR type reactors or of pressurizer and steam generator of PWR type reactors. In addition to the design study of the university of Tokyo, technology development of the SCPR for practical use has started under the collaboration of industry and academia since 2000. Mockup single tube and bundle tests for heat transfer/fluid flow characteristics of the design have been conducted with 3D heat transfer analysis. Materials compatible with coolant conditions for fuel cans and reactor internals are also assessed. Overall evaluation of the reactor concept is under way. (T. Tanaka)

Moving ring reactor 'Karin-1'

International Nuclear Information System (INIS)

1983-12-01

The conceptual design of a moving ring reactor ''Karin-1'' has been carried out to advance fusion system design, to clarify the research and development problems, and to decide their priority. In order to attain these objectives, a D-T reactor with tritium breeding blanket is designed, a commercial reactor with net power output of 500 MWe is designed, the compatibility of plasma physics with fusion engineering is demonstrated, and some other guideline is indicated. A moving ring reactor is composed mainly of three parts. In the first formation section, a plasma ring is formed and heated up to ignition temperature. The plasma ring of compact torus is transported from the formation section through the next burning section to generate fusion power. Then the plasma ring moves into the last recovery section, and the energy and particles of the plasma ring are recovered. The outline of a moving ring reactor ''Karin-1'' is described. As a candidate material for the first wall, SiC was adopted to reduce the MHD effect and to minimize the interaction with neutrons and charged particles. The thin metal lining was applied to the SiC surface to solve the problem of the compatibility with lithium blanket. Plasma physics, the engineering aspect and the items of research and development are described. (Kako, I.)

Proposal of a fast gas-cooled reactor using transuranics

International Nuclear Information System (INIS)

Macedo, Anderson Altair Pinheiro de

2016-01-01

In the last two decades, nations that have invested in research and energy generation through nuclear source have devoted part of their efforts in developing new technologies for nuclear reactors. Part of this investment focuses on new material testing, particularly regarding new fuels. In a world view that breaths sustainability, the reprocess and reuse of spent fuel from conventional reactors comes alive in nuclear technology, presenting itself as a real alternative of energy source for the latest generation of reactors. Different concepts of fourth generation reactors have been proposed and must meet some basic requirements, such as: extended burnup, improvement of passive safety, better radioactive waste management, possibility to use reprocessed fuel and proliferation resistance. In this context, the GFR (Gas-cooled Fast Reactor) is one of the future promises, presenting satisfactory neutronic results on the use of type of fuel (U, Pu) C. In the present work, the fuel of a traditional GFR reactor that uses (U, Pu)C was sub was replaced by a transuranic reprocessed fuel (TRU), obtained by non-proliferation reprocessing technology. The UO 2 fuel initially enriched by 3.1% was burned in a standard PWR, with full burn of 33,000 MWd/T. Afterward it was left in a pool for 5 years and finally reprocessed by UREX + method. Two fuels were studied and evaluated, one diluted with depleted uranium (U, TRU)C, and the other diluted in thorium (Th, TRU)C. Assessments were done in steady state and as well as during burning and were compared with results obtained using the standard fuel, (U, Pu) C. The outcome shows that the use of TRU as a fuel, in GFR type reactors, is a real possibility. The research was done using the SCALE 6.0 code modules. (author)

The C language auto-generation of reactor trip logic caused by steam generator water level using CASE tools

International Nuclear Information System (INIS)

Kim, Jang Yeol; Lee, Jang Soo

1999-01-01

The purpose is to produce a model of nuclear reactor trip logic caused by the steam generator water level of Wolsung 2/3/4 unit through an activity chart and a statechart and to produce C language automatically using statechart-based formalism and statemate MAGNUM toolset suggested by David Harel Formalism. It was worth attempting auto-generation of C language through we manually made Software Requirement specification(SRS) for safety-critical software using statechart-based formalism. Most of the phase of the software life-cycle except the software requirement specification of an analysis phase were generated automatically by Computer Aided Software Engineering(CASE) tools. It was verified that automatically produced C language has high productivity, portability, and quality through the simulation. (Author). 6 refs., 6 figs

OECD Halden reactor project

International Nuclear Information System (INIS)

1978-01-01

This report summarizes the activities of the OECD Halden Reactor Project for the year 1976. The main items reported on are: a) the process supervision and control which have focused on core monitoring and control, and operator-process communication; b) the fuel performance and safety behavior which have provided data and analytical descriptions of the thermal, mechanical and chemical behavior of fuel under various operating conditions; c) the reactor operations and d) the administration and finance

Research and development of a super fast reactor (12). Considerations for the reactor characteristics

International Nuclear Information System (INIS)

Goto, Shoji; Ishiwatari, Yuki; Oka, Yoshiaki

2008-01-01

A research program aimed at developing the Super Fast Reactor (Super FR) has been entrusted by the Ministry of Education, Culture, Sports, Science and Technology (MEXT) of Japan since December 2005. It includes the following three projects. (A) Development of the Super Fast Reactor concept. (B)Thermal-hydraulic experiments. (C) Materials development. Tokyo Electric Power Company (TEPCO) has joined this program and works on part (A) together with the University of Tokyo. From the utility's viewpoint, it is important to consider the most desirable characteristics for Super FR to have. Four issues were identified in project (A), (1) Fuel design, (2) Reactor core design, (3) Safety, and (4) Plant characteristics of Super FR. This report describes the desired characteristics of Super FR with respect to item (1) fuel design and item (2) Reactor core design, as compared with a boiling water reactor (BWR) plant. The other two issues will be discussed in this project, and will also be considered in the design process of Super FR. (author)

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

Energy Technology Data Exchange (ETDEWEB)

M. J. Appel and J. M. Capron

2007-07-25

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes.

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.; Capron, J.M.

2007-01-01

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes

Upflow anaerobic sludge reactors for the treatment of combined industrial effluent in subtropical conditions: a comparison between UASB and UASF reactors

International Nuclear Information System (INIS)

Yasar, A.; Ahmad, N.; Chaudhry, M.N.; Sarwar, M.; Masood, T.; Yaqub, A.

2005-01-01

The performance of anaerobic biological process is heavily process conditions dependent. In this study, an attempt has been made to investigate the influence of process conditions like temperature, sludge age and hydraulic retention time (HRT) on the efficiency of an upflow anaerobic sludge blanket (UASB) reactor and upflow anaerobic sludge filter (UASF) to treat combined industrial wastewater. Reactors were operated at easing ambient temperatures (38, 30, 20 and 14 deg. C) and correspondingly increasing sludge ages (60, 90, 120 and 150 days). At temperature 38 deg. C and sludge age of 60 days, UASF showed better performance than VASE reactor. This mainly due to the enhanced filtration through well-graded sand filter and fairly good biological activity in UASF. At this stage, lack of sludge granulation in VASE reactor resulted in poor biological activity; hence, relatively poor performance. At temperatures 30 and 20 deg. C with sludge ages of 90 and 120 days, respectively, UASB gave better results than UASF. The reason was rapid biological degradation due to proper sludge granulation and favorable temperature. At temperature 14 deg. C, a substantial decrease in the efficiency of UASB reactor as compared to the UASF was evident. Drop in efficiency was because of inhabitation of methanogenic bacteria and liquidation of sludge granules. These factors mounted to a decrease in biological activity, stoppage as production and an increase in total suspended solids (TSS) in the effluent. The influence of hydraulic retention time (ranging between 3-12 hours at an increment of 3 hours) on the removal efficiency of both UASB and UASF was not significant. At favorable temperature (20 to 30 deg. C) and sludge age (90 to 120 days) UASB reactor appeared to be more efficient than UASF.(author)

A novel spiral reactor for biodiesel production in supercritical ethanol

International Nuclear Information System (INIS)

Farobie, Obie; Sasanami, Kazuma; Matsumura, Yukihiko

2015-01-01

Highlights: • A novel spiral reactor for biodiesel production in supercritical ethanol was proposed. • The spiral reactor employed in this study successfully recovered heat. • The effects of temperature and time on FAEE yield were investigated. • FAEE yield as high as 0.937 mol/mol was obtained at 350 °C after 30 min. • The second-order kinetic model expressed the experimental yield well. - Abstract: A spiral reactor is proposed as a novel reactor design for biodiesel production under supercritical conditions. Since the spiral reactor serves as a heat exchanger, it offers the advantage of reduced apparatus space compared to conventional supercritical equipment. Experimental investigations were carried out at reaction temperatures of 270–400 °C, pressure of 20 MPa, oil-to-ethanol molar ratio of 1:40, and reaction times of 3–30 min. An FAEE yield of 0.937 mol/mol was obtained in a short reaction time of 30 min at 350 °C and oil-to-ethanol molar ratio of 1:40 under a reactor pressure of 20 MPa. The spiral reactor was not only as effective as conventional reactor in terms of transesterification reactor but also was superior in terms of heat recovery. A second-order kinetic model describing the transesterification of canola oil in supercritical ethanol was proposed, and the reaction was observed to follow Arrhenius behavior. The corresponding reaction rate constants and the activation energies as well as pre-exponential factors were determined

Management of research reactor ageing

International Nuclear Information System (INIS)

1995-03-01

As of December 1993, about one quarter of the operating research reactors were over 30 years old. The long life of research reactors has raised some concern amongst research reactor operators, regulators and, to some extent, the general public. The International Atomic Energy Agency commenced activities on the topic of research reactor ageing by appointing an internal working group in 1988 and convening a Consultants Meeting in 1989. The subject was also discussed at an international symposium and a regional seminar held in 1989 and 1992 respectively. A draft document incorporating information and experience exchanged at the above meetings was reviewed by a Technical Committee Meeting held in Vienna in 1992. The present TECDOC is the outcome of this meeting and contains recommendations, guidelines and information on the management of research reactor ageing, which should be used in conjunction with related publications of the IAEA Research Reactor Safety Programme, which are referenced throughout the text. This TECDOC will be of interest to operators and regulators involved with the safe operation of any type of research reactor to (a) understand the behaviour and influence of ageing mechanisms on the reactor structures, systems and components; (b) detect and assess the effect of ageing; (c) establish preventive and corrective measures to mitigate these effects; and (d) make decisions aimed at the safe and continued operation of a research reactor. 32 refs, tabs

Management of research reactor ageing

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

As of December 1993, about one quarter of the operating research reactors were over 30 years old. The long life of research reactors has raised some concern amongst research reactor operators, regulators and, to some extent, the general public. The International Atomic Energy Agency commenced activities on the topic of research reactor ageing by appointing an internal working group in 1988 and convening a Consultants Meeting in 1989. The subject was also discussed at an international symposium and a regional seminar held in 1989 and 1992 respectively. A draft document incorporating information and experience exchanged at the above meetings was reviewed by a Technical Committee Meeting held in Vienna in 1992. The present TECDOC is the outcome of this meeting and contains recommendations, guidelines and information on the management of research reactor ageing, which should be used in conjunction with related publications of the IAEA Research Reactor Safety Programme, which are referenced throughout the text. This TECDOC will be of interest to operators and regulators involved with the safe operation of any type of research reactor to (a) understand the behaviour and influence of ageing mechanisms on the reactor structures, systems and components; (b) detect and assess the effect of ageing; (c) establish preventive and corrective measures to mitigate these effects; and (d) make decisions aimed at the safe and continued operation of a research reactor. 32 refs, tabs.

On-line Monitoring of Instrumentation in Research Reactors

International Nuclear Information System (INIS)

2017-12-01

This publication is the result of a benchmarking effort undertaken under the IAEA coordinated research project on improved instrumentation and control (I&C) maintenance techniques for research reactors. It lays the foundation for implementation of on-line monitoring (OLM) techniques and establishment of the validity of those for improved maintenance practices in research reactors for a number of applications such as change to condition based calibration, performance monitoring of process instrumentation systems, detection of process anomalies and to distinguish between process problems/effects and instrumentation/sensor issues. The techniques and guidance embodied in this publication will serve the research reactor community in providing the technical foundation for implementation of OLM techniques. It is intended to be used by Member States to implement I&C maintenance and to improve performance of research reactors.

Political-social reactor problems at Berkeley

International Nuclear Information System (INIS)

Little, G.A.

1980-01-01

For better than ten years there was little public notice of the TRIGA reactor at UC-Berkeley. Then: a) A non-student persuaded the Student and Senate to pass a resolution to request Campus Administration to stop operation of the reactor and remove it from campus. b) Presence of the reactor became a campaign-issue in a City Mayoral election. c) Two local residents reported adverse physical reactions before, during, and after a routine tour of the reactor facility. d) The Berkeley City Council began a study of problems associated with radioactive material within the city. e) Friends Of The Earth formally petitioned the NRC to terminate the reactor's license. Campus personnel have expended many man-hours and many pounds of paper in responding to these happenings. Some of the details are of interest, and may be of use to other reactor facilities. (author)

TerraPower, Bill Gates' reactor

International Nuclear Information System (INIS)

Guidez, J.

2016-01-01

TerraPower is a traveling wave reactor, it means that the reactor gradually converts non fissile material into the fuel it needs and the active part of the core progressively moves through the core leaving spent fuel behind. The last design of the TerraPower shows that it will use depleted uranium as fuel and that its core will need reloading every 10 years. Re-arrangement of the nuclear fuel will have to be made every 18 months to keep the core reactive. Metallic nuclear fuels will be used as they allow the highest breeding rates. It appears that apart from the very specific configuration of the core, the TerraPower is a reactor very similar to sodium-cooled fast reactors. Neutron transport inside traveling wave reactor core is complex and simulations show that the piling-up of fission product tends to kill the chain reaction and a continuous neutron addition may be necessary to keep the reactor going. A large part of the TerraPower feasibility studies concerns neutron transport inside its core. (A.C.)

Dynamic simulation platform to verify the performance of the reactor regulating system for a research reactor

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-07-01

Digital instrumentation and controls system technique is being introduced in new constructed research reactor or life extension of older research reactor. Digital systems are easy to change and optimize but the validated process for them is required. Also, to reduce project risk or cost, we have to make it sure that configuration and control functions is right before the commissioning phase on research reactor. For this purpose, simulators have been widely used in developing control systems in automotive and aerospace industries. In these literatures, however, very few of these can be found regarding test on the control system of research reactor with simulator. Therefore, this paper proposes a simulation platform to verify the performance of RRS (Reactor Regulating System) for research reactor. This simulation platform consists of the reactor simulation model and the interface module. This simulation platform is applied to I and C upgrade project of TRIGA reactor, and many problems of RRS configuration were found and solved. And it proved that the dynamic performance testing based on simulator enables significant time saving and improves economics and quality for RRS in the system test phase. (authors)

Grey water treatment in upflow anaerobic sludge blanket (UASB) reactor at different temperatures.

Science.gov (United States)

Elmitwalli, Tarek; Otterpohl, Ralf

2011-01-01

The treatment of grey water in two upflow anaerobic sludge blanket (UASB) reactors, operated at different hydraulic retention times (HRTs) and temperatures, was investigated. The first reactor (UASB-A) was operated at ambient temperature (14-25 degrees C) and HRT of 20, 12 and 8 h, while the second reactor (UASB-30) was operated at controlled temperature of 30 degrees C and HRT of 16, 10 and 6 h. The two reactors were fed with grey water from 'Flintenbreite' settlement in Luebeck, Germany. When the grey water was treated in the UASB reactor at 30 degrees C, total chemical oxygen demand (CODt) removal of 52-64% was achieved at HRT between 6 and 16 h, while at lower temperature lower removal (31-41%) was obtained at HRT between 8 and 20 h. Total nitrogen and phosphorous removal in the UASB reactors were limited (22-36 and 10-24%, respectively) at all operational conditions. The results showed that at increasing temperature or decreasing HRT of the reactors, maximum specific methanogenic activity of the sludge in the reactors improved. As the UASB reactor showed a significantly higher COD removal (31-64%) than the septic tank (11-14%) even at low temperature, it is recommended to use UASB reactor instead of septic tank (the most common system) for grey water pre-treatment. Based on the achieved results and due to high peak flow factor, a HRT between 8 and 12 h can be considered the suitable HRT for the UASB reactor treating grey water at temperature 20-30 degrees C, while a HRT of 12-24 h can be applied at temperature lower than 20 degrees C.

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

Energy Technology Data Exchange (ETDEWEB)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO/sub 2/) and lithium silicate (Li/sub 2/SiO/sub 3/) by the reaction: Li/sup 6/ + n ..-->.. /sup 4/He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100/sup 0/C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T/sub 2/), while in laboratory extractions (300-1300/sup 0/C), the tritium appeared primarily in the condensible form (HTO and T/sub 2/O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H/sub 2/O, CO/sub 2/, CO, O/sub 2/, H/sub 2/, NO, SO/sub 2/, SiF/sub 4/ and traces of hydrocarbons.

A compact reactor/ORC power source

International Nuclear Information System (INIS)

Meier, K.L.; Kirchner, W.L.; Willcutt, G.J.

1986-01-01

A compact power source that combines an organic Rankine cycle (ORC) electric generator with a nuclear reactor heat source is being designed and fabricated. Incorporating existing ORC technology with proven reactor technology, the compact reactor/ORC power source offers high reliability while minimizing the need for componenet development. Thermal power at 125 kWt is removed from the coated particle fueled, graphite moderated reactor by heat pipes operating at 500 0 C. Outside the reactor vessel and connected to the heat pipes are vaporizers in which the toluene ORC working fluid is heated to 370 0 C. In the turbine-alternator-pump (TAP) combined-rotating unit, the thermal energy of the toluene is converted to 25 kWe of electric power. Lumped parameter systems analyses combined with a finite element thermal analyses combined with a finite element thermal analysis have aided in the power source design. The analysis have provided assurance of reliable multiyear normal operation as well as full power operation with upset conditions, such as failed heat pipes and inoperative ORC vaporizers. Because of inherent high reliability, long life, and insensitivity to upset conditions, this power source is especially suited for use in remote, inaccessible locations where fuel delivery and maintenance costs are high

Higher plant availability and reduced reactor scram frequency in PWRs by appropriate system and I and C design

International Nuclear Information System (INIS)

Frei, G.; Weber, J.

1987-01-01

High plant availability and reliability are guaranteed by appropriate design of reactor and BOP systems, this including the plant I and C systems. It is of advantage to have design, construction and commissioning of the plant concentrated in the hands of a single company to avoid interface problems between the different areas of the plant. The integrated overall control concept developed by KWU with control, limitation and protection systems as well as optimized operational and monitoring systems assisted by instrumentation channel redundance and logic for selection of the second highest (or second lowest) signal value as appropriate for comparison with limitation setpoints, minimize the severity of transients. This results in a reduction in the frequency of reactor scrams and of unnecessary actuation of safety systems. Dynamic plant behavior is described for a number of examples where the improved plant behavior resulting from the above design features enhances plant availability

UCLA program in reactor studies: The ARIES tokamak reactor study

International Nuclear Information System (INIS)

1991-01-01

The ARIES research program is a multi-institutional effort to develop several visions of tokamak reactors with enhanced economic, safety, and environmental features. The aims are to determine the potential economics, safety, and environmental features of a range of possible tokamak reactors, and to identify physics and technology areas with the highest leverage for achieving the best tokamak reactor. Four ARIES visions are currently planned for the ARIES program. The ARIES-1 design is a DT-burning reactor based on ''modest'' extrapolations from the present tokamak physics database and relies on either existing technology or technology for which trends are already in place, often in programs outside fusion. ARIES-2 and ARIES-4 are DT-burning reactors which will employ potential advances in physics. The ARIES-2 and ARIES-4 designs employ the same plasma core but have two distinct fusion power core designs; ARIES-2 utilize the lithium as the coolant and breeder and vanadium alloys as the structural material while ARIES-4 utilizes helium is the coolant, solid tritium breeders, and SiC composite as the structural material. Lastly, the ARIES-3 is a conceptual D- 3 He reactor. During the period Dec. 1, 1990 to Nov. 31, 1991, most of the ARIES activity has been directed toward completing the technical work for the ARIES-3 design and documenting the results and findings. We have also completed the documentation for the ARIES-1 design and presented the results in various meetings and conferences. During the last quarter, we have initiated the scoping phase for ARIES-2 and ARIES-4 designs

Low Temperature (320 deg C and 340 deg C) Creep Crack Growth in Low Alloy Reactor Pressure Vessel Steel

International Nuclear Information System (INIS)

Rui Wu; Sandstroem, Rolf; Seitisleam, Facredin

2004-02-01

Uni-axial creep and creep crack growth (CCG) tests at 320 deg C and 340 deg C as well as post test metallography have been carried out in a low alloy reactor pressure vessel steel (ASTM A508 class 2) having simulated coarse grained heat affected zone microstructure. The CCG behaviour is studied in terms of steady crack growth rate, creep fracture parameter C*, stress intensity factor and reference stress at given testing conditions. It has been found that CCG does occur at both tested temperatures. The lifetimes for the CCG tests are considerably shorter than those for the uni-axial creep tests. This is more pronounced at longer lifetimes or lower stresses. Increasing temperature from 320 deg C to 340 deg C causes a reduction of lifetime by approximately a factor of five and a corresponding increase of steady crack growth rate. For the CCG tests, there are three regions when the crack length is plotted against time. After incubation, the crack grows steadily until it accelerates when rupture is approached. Notable crack growth takes place at later stage of the tests. No creep cavitation is observed and transgranular fracture is dominant for the uni-axial creep specimens. In the CT specimens the cracks propagate intergranularly, independent of temperature and time. Some relations between time to failure, reference stress and steady crack growth rate are found for the CCG tests. A linear extrapolation based on the stress-time results indicates that the reference stress causing failure due to CCG at a given lifetime of 350,000 hours at 320 deg C is clearly lower than both yield and tensile strengths, on which the design stress may have based. Therefore, caution must be taken to prevent premature failure due to low temperature CCG. Both uni-axial and CCG tests on real welded joint at 320 deg C, study of creep damage zone at crack tip as well as numerical simulation are recommended for future work

Nuclear propulsion apparatus with alternate reactor segments

International Nuclear Information System (INIS)

Szekely, T.

1979-01-01

Nuclear propulsion apparatus comprising: (a) means for compressing incoming air; (b) nuclear fission reactor means for heating said air; (c) means for expanding a portion of the heated air to drive said compressing means; (d) said nuclear fission reactor means being divided into a plurality of radially extending segments; (e) means for directing a portion of the compressed air for heating through alternate segments of said reactor means and another portion of the compressed air for heating through the remaining segments of said reactor means; and (f) means for further expanding the heated air from said drive means and the remaining heated air from said reactor means through nozzle means to effect reactive thrust on said apparatus. 12 claims

Circumferential tensile test method for mechanical property evaluation of SiC/SiC tube

Energy Technology Data Exchange (ETDEWEB)

Yu, Ju-Hyeon, E-mail: 15096018@mmm.muroran-it.ac.jp [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kishimoto, Hirotatsu [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Park, Joon-soo [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Nakazato, Naofumi [Graduate School, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan); Kohyama, Akira [OASIS, Muroran Institute of Technology, 27-1, Muroran, Hokkaido (Japan)

2016-11-01

Highlights: • NITE SiC/SiC cooling channel system to be a candidate of divertor system in future. • Hoop strength is one of the important factors for a tube. • This research studies the relationship between deformation and strain of SiC/SiC tube. - Abstract: SiC fiber reinforced/SiC matrix (SiC/SiC) composite is expected to be a candidate material for the first-wall, components in the blanket and divertor of fusion reactors in future. In such components, SiC/SiC composites need to be formed to be various shapes. SiC/SiC tubes has been expected to be employed for blanket and divertor after DEMO reactor, but there is not established mechanical investigation technique. Recent progress of SiC/SiC processing techniques is likely to realize strong, having gas tightness SiC/SiC tubes which will contribute for the development of fusion reactors. This research studies the relationship between deformation and strain of SiC/SiC tube using a circumferential tensile test method to establish a mechanical property investigation method of SiC/SiC tubes.

IRSN research programs concerning reactor safety

International Nuclear Information System (INIS)

Bardelay, J.

2005-01-01

This paper is made up of 3 parts. The first part briefly presents the missions of IRSN (French research institute on nuclear safety), the second part reviews the research works currently led by IRSN in the following fields : -) the assessment of safety computer codes, -) thermohydraulics, -) reactor ageing, -) reactivity accidents, -) loss of coolant, -) reactor pool dewatering, -) core meltdown, -) vapor explosion, and -) fission product release. In the third part, IRSN is shown to give a major importance to experimental programs led on research or test reactors for collecting valid data because of the complexity of the physical processes that are involved. IRSN plans to develop a research program concerning the safety of high or very high temperature reactors. (A.C.)

Change of I-V characteristics of SiC diodes upon reactor irradiation; Modification des caracteristiques I-V de jonctions p-n au SiC du fait d'une irradiation dans un reacteur; Izmeneniya kharakteristik I-V vyrashchennogo v SiC perekhoda tipa p-n posle oblucheniya ego v reaktore; Modificaciones que sufren por irradiacion en un reactor las caracteristicas I-V de uniones p-n en SiC

Energy Technology Data Exchange (ETDEWEB)

Heerschap, M; De Coninck, R [Solid State Physics Dept., SCK-CEN, Mol (Belgium)

1962-04-15

In search for semiconductors, which can be used in high-flux reactors in order to measure flux distributions, we irradiated SiC p-n junctions in the Belgium BR-1 reactor. Two types of SiC-diodes of different origin have been irradiated. These junctions are grown in the Lely-furnace. The change in forward and reverse characteristics have been measured during and after irradiation up to temperatures of 150{sup o}C, while measurements up to a temperature of 500{sup o}C are in progress. It has been found that one type resists BR-1 neutrons up to an integrated flux of 10{sup 15} n/cm{sup 2}, while the other resists irradiation up to a flux of 10{sup 17} n/cm{sup 2}. The changes in characteristics are given as well as the result of some annealing experiments. (author) [French] En recherchant des semi-conducteurs pouvant servir a mesurer les distributions de flux dans les reacteurs a haut flux de neutrons, les auteurs ont irradie des jonctions p-n au SiC dans le reacteur belge BR-1. Deux types de diodes a SiC d'origines differentes ont ete ainsi irradies. Les jonctions en question sont preparees par etirage dans le four Lely. Les auteurs ont mesure les modifications subies par les caracteristiques I-V apres et pendant l'irradiation a des temperatures allant jusqu'a 150{sup o}C; ils poursuivent leurs mesures dans la gamme des temperatures allant de 150{sup o}C a 500{sup o}C. Us ont constate que l'un des types de diode a SiC resiste aux neutrons du reacteur BR-1 jusqu'a 10{sup 15} n/cm{sup 2}, tandis que l'autre type resiste a l'irradiation jusqu'a 10{sup 17} n/cm{sup 2}. Les auteurs indiquent les modifications subies par les caracteristiques, ainsi que le resultat de certaines experiences de recuit. (author) [Spanish] Los autores estan tratando de encontrar semiconductores con los que sea posible medir distribuciones de flujo en reactores de flujo elevado, y con este fin irradiaron uniones p-n del SiC en el reactor BR-1 de Belgica. Irradiaron dos tipos de diodos de SiC de

Comparative Study on Cyber Securities between Power Reactor and Research Reactor with Bayesian Update

International Nuclear Information System (INIS)

Shin, Jinsoo; Heo, Gyunyoung; Son, Han Seong

2016-01-01

The Stuxnet has shown that nuclear facilities are no more safe from cyber-attack. Due to practical experiences and concerns on increasing of digital system application, cyber security has become the important issue in nuclear industry. Korea Institute of Nuclear Nonproliferation and control (KINAC) published a regulatory standard (KINAC/RS-015) to establish cyber security framework for nuclear facilities. However, it is difficult to research about cyber security. It is hard to quantify cyber-attack which has malicious activity which is different from existing design basis accidents (DBAs). We previously proposed a methodology on development of a cyber security risk model with BBN. However, the methodology had a limitation in which the input data as prior information was solely on expert opinions. In this study, we propose a cyber security risk model for instrumentation and control (I and C) system of nuclear facilities with some equation for quantification by using Bayesian Belief Network (BBN) in order to overcome the limitation of previous research. The proposed model has been used for comparative study on cyber securities between large-sized nuclear power plants (NPPs) and small-sized Research Reactors (RR). In this study, we proposed the cyber security risk evaluation model with BBN. It includes I and C architecture, which is a target system of cyber-attack, malicious activity, which causes cyber-attack from attacker, and mitigation measure, which mitigates the cyber-attack risk. Likelihood and consequence as prior information are evaluated by considering characteristics of I and C architecture and malicious activity. The BBN model provides posterior information with Bayesian update by adding any of assumed cyber-attack scenarios as evidence. Cyber security risk for nuclear facilities is analyzed by comparing between prior information and posterior information of each node. In this study, we conducted comparative study on cyber securities between power reactor

Comparative Study on Cyber Securities between Power Reactor and Research Reactor with Bayesian Update

Energy Technology Data Exchange (ETDEWEB)

Shin, Jinsoo; Heo, Gyunyoung [Kyung Hee University, Yongin (Korea, Republic of); Son, Han Seong [Joongbu Univiersity, Geumsan (Korea, Republic of)

2016-10-15

The Stuxnet has shown that nuclear facilities are no more safe from cyber-attack. Due to practical experiences and concerns on increasing of digital system application, cyber security has become the important issue in nuclear industry. Korea Institute of Nuclear Nonproliferation and control (KINAC) published a regulatory standard (KINAC/RS-015) to establish cyber security framework for nuclear facilities. However, it is difficult to research about cyber security. It is hard to quantify cyber-attack which has malicious activity which is different from existing design basis accidents (DBAs). We previously proposed a methodology on development of a cyber security risk model with BBN. However, the methodology had a limitation in which the input data as prior information was solely on expert opinions. In this study, we propose a cyber security risk model for instrumentation and control (I and C) system of nuclear facilities with some equation for quantification by using Bayesian Belief Network (BBN) in order to overcome the limitation of previous research. The proposed model has been used for comparative study on cyber securities between large-sized nuclear power plants (NPPs) and small-sized Research Reactors (RR). In this study, we proposed the cyber security risk evaluation model with BBN. It includes I and C architecture, which is a target system of cyber-attack, malicious activity, which causes cyber-attack from attacker, and mitigation measure, which mitigates the cyber-attack risk. Likelihood and consequence as prior information are evaluated by considering characteristics of I and C architecture and malicious activity. The BBN model provides posterior information with Bayesian update by adding any of assumed cyber-attack scenarios as evidence. Cyber security risk for nuclear facilities is analyzed by comparing between prior information and posterior information of each node. In this study, we conducted comparative study on cyber securities between power reactor

IAEA programme on research reactor safety

International Nuclear Information System (INIS)

Alcala, F.; Di Meglio, A.F.

1995-01-01

This paper describes the IAEA programme on research reactor safety and includes the safety related areas of conversions to the use of low enriched uranium (LEU) fuel. The program is based on the IAEA statutory responsibilities as they apply to the requirements of over 320 research reactors operating around the world. The programme covers four major areas: (a) the development of safety documents; (b) safety missions to research reactor facilities; (c) support of research programmes on research reactor safety; (d) support of Technical Cooperation projects on research reactor safety issues. The demand for these activities by the IAEA member states has increased substantially in recent years especially in developing countries with increasing emphasis being placed on LEU conversion matters. In response to this demand, the IAEA has undertaken an extensive programme for each of the four areas above. (author)

Simultaneous Production of Hydrogen and Methane from Sugar Beet Molasses in a Two Phase Anaerobic Digestion System in UASB Reactors under Thermophilic Temperature (55 Deg C)

Energy Technology Data Exchange (ETDEWEB)

Kongjan, P.; Villafa, S.; Beltran, P.; Min, B.; Angelidaki, I. (Dept. of Environmental Engineering, Technical Univ. of Denmark, DK-2800, Lyngby (Denmark)). e-mail: pak@env.dtu.dk

2008-10-15

Simultaneous production of hydrogen and methane in two sequential stages of acidogenic and methanogenic step was investigated in two serial operated up-flow anaerobic sludge bed (UASB) reactors at thermophilic temperature (55 deg C). Hydrogen production from molasses was carried out in the first reactor at the hydraulic retention time (HRT) of 1 day. Molasses were converted into hydrogen with the yield of 1.3 mole-H{sub 2}/mole-hexose{sub added} or 82.7 ml- H{sub 2}/g-VS{sub added} of molasses, and the hydrogen productivity was 2696 ml-H{sub 2}/dxl{sub reactor}. The effluent (mainly butyrate, acetate and lactate) after the acidogenic process was subsequently fed to the second reactor for methane production at HRT of 3 days. Methane production yield of 255 ml-H{sub 2}/g-VS{sub added} of influent or 130.1 ml-H{sub 2}/g-VS{sub added} of molasses and methane production rate of 1056 ml/dxl{sub reactor} were obtained. Significant decrease of volatile fatty acids (VFAs) was also observed in the effluent of the second reactor. A two phase anaerobic digestion was successfully demonstrated for molasses as a potential substrate to produce hydrogen and subsequent methane in the UASB reactors

Generation IV reactors: international projects

International Nuclear Information System (INIS)

Carre, F.; Fiorini, G.L.; Kupitz, J.; Depisch, F.; Hittner, D.

2003-01-01

Generation IV international forum (GIF) was initiated in 2000 by DOE (American department of energy) in order to promote nuclear energy in a long term view (2030). GIF has selected 6 concepts of reactors: 1) VHTR (very high temperature reactor system, 2) GHR (gas-cooled fast reactor system), 3) SFR (sodium-cooled fast reactor system, 4) SCWR (super-critical water-cooled reactor system), 5) LFR (lead-cooled fast reactor system), and 6) MFR (molten-salt reactor system). All these 6 reactor systems have been selected on criteria based on: - a better contribution to sustainable development (through their aptitude to produce hydrogen or other clean fuels, or to have a high energy conversion ratio...) - economic profitability, - safety and reliability, and - proliferation resistance. The 6 concepts of reactors are examined in the first article, the second article presents an overview of the results of the international project on innovative nuclear reactors and fuel cycles (INPRO) within IAEA. The project finished its first phase, called phase-IA. It has produced an outlook into the future role of nuclear energy and defined the need for innovation. The third article is dedicated to 2 international cooperations: MICANET and HTR-TN. The purpose of MICANET is to propose to the European Commission a research and development strategy in order to develop the assets of nuclear energy for the future. Future reactors are expected to be more multiple-purposes, more adaptable, safer than today, all these developments require funded and coordinated research programs. The aim of HTR-TN cooperation is to promote high temperature reactor systems, to develop them in a long term perspective and to define their limits in terms of burn-up and operating temperature. (A.C.)

Occupational radiation exposure at Commercial Nuclear Power reactors 1983. Volume 5. Annual report

International Nuclear Information System (INIS)

Brooks, B.G.

1985-03-01

This report presents an updated compilation of occupational radiation exposure at commercial nuclear power reactors for the years 1969 through 1983. The summary based on information received from the 75 light-water-cooled reactors (LWRs) and one high temperature gas-cooled reactor (HTGR). The total number of personnel monitored at LWRs in 1983 was 136,700. The number of workers that received measurable doses during 1983 and 85,600 which is about 1000 more than that found in 1982. The total collective dose at LWRs for 1983 is estimated to be 56,500 man-rems (man-cSv), which is about 4000 more man-rems (man-cSv) than that reported in 1982. This resulted in the average annual dose for each worker who received a measurable dose increasing slightly to 0.66 rems (cSv), and the average collective dose per reactor increasing by about 50 man-rems (man-cSv), and the average collective dose per reactor increasing by about 50 man-rems (man-cSv) to a value of 753 man-rems (man-cSv). The collective dose per megawatt of electricity generated by each reactor also increased slightly to an average value of 1.7 man-rems (man-cSv) per megawatt-year. Health implications of these annual occupational doses are discussed

Conceptual design study of fusion experimental reactor (FY86 FER)

International Nuclear Information System (INIS)

Kobayashi, Takeshi; Yamada, Masao; Mizoguchi, Tadanori

1987-09-01

This report describes the results of the reactor configuration/structure design for the fusion experimental reactor (FER) performed in FY 1986. The design was intended to meet the physical and engineering mission of the next step device which was decided by the subcommittee on the next step device of the nuclear fusion council. The objectives of the design study in FY 1986 are to advance and optimize the design concept of the last year because the recommendation of the subcommittee was basically the same as the design philosophy of the last year. Six candidate reactor configurations which correspond to options C ∼ D presented by the subcommittee were extensively examined. Consequently, ACS reactor (Advanced Option-C with Single Null Divertor) was selected as the reference configuration from viewpoints of technical risks and cost performance. Regarding the reactor structure, the following items were investigated intensively: minimization of reactor size, protection of first wall against plasma disruption, simplification of shield structure, reactor configuration which enables optimum arrangement of poloidal field coils. (author)

Reactor theory and power reactors. 1. Calculational methods for reactors. 2. Reactor kinetics

International Nuclear Information System (INIS)

Henry, A.F.

1980-01-01

Various methods for calculation of neutron flux in power reactors are discussed. Some mathematical models used to describe transients in nuclear reactors and techniques for the reactor kinetics' relevant equations solution are also presented

A series of lectures on operational physics of power reactors

International Nuclear Information System (INIS)

Mohanakrishnan, P.; Rastogi, B.P.

1982-01-01

This report discusses certain aspects of operational physics of power reactors. These form a lecture series at the Winter College on Nuclear Physics and Reactors, Jan. - March 1980, conducted at the International Centre for Theoretical Physics, Trieste, Italy. The topics covered are (a) the reactor physics aspects of fuel burnup (b) theoretical methods applied for burnup prediction in power reactors (c) interpretation of neutron detector readings in terms of adjacent fuel assembly powers (d) refuelling schemes used in power reactors. The reactor types chosen for the discussion are BWR, PWR and PHWR. (author)

Calculation of the power distribution in the fuel rods of the low power research reactor using the MCNP4C code

International Nuclear Information System (INIS)

Dawahra, S.; Khattab, K.

2012-01-01

The Monte Carlo method, using the MCNP4C code, was used in this paper to calculate the power distribution in 3-D geometry in the fuel rods of the Syrian Miniature Neutron Source Reactor (MNSR). To normalize the MCNP4C result to the steady state nominal thermal power, the appropriate scaling factor was defined to calculate the power distribution precisely. The maximum power of the individual rod was found in the fuel ring number 2 and was found to be 105 W. The minimum power was found in the fuel ring number 9 and was 79.9 W. The total power in the total fuel rods was 30.9 k W. This result agrees very well with nominal power reported in the reactor safety analysis report which equals 30 k W. Finally, the peak power factors, which are defined as the ratios between the maximum to the average and the maximum to the minimum powers were calculated to be 1.18 and 1.31 respectively. (author)

Nuclear reactors to come

International Nuclear Information System (INIS)

Lung, M.

2002-01-01

The demand for nuclear energy will continue to grow at least till 2050 because of mainly 6 reasons: 1) the steady increase of the world population, 2) China, India and Indonesia will reach higher social standard and their energy consumption will consequently grow, 3) fossil energy resources are dwindling, 4) coal will be little by little banned because of its major contribution to the emission of green house effect gas, 5) renewable energies need important technological jumps to be really efficient and to take the lead, and 6) fusion energy is not yet ready to take over. All these reasons draw a promising future for nuclear energy. Today 450 nuclear reactors are operating throughout the world producing 17% of the total electrical power demand. In order to benefit fully of this future, nuclear industry has to improve some characteristics of reactors: 1) a more efficient use of uranium (it means higher burnups), 2) a simplification and automation of reprocessing-recycling chain of processes, 3) efficient measures against proliferation and against any misuse for terrorist purposes, and 4) an enhancement of safety for the next generation of reactors. The characteristics of fast reactors and of high-temperature reactors will likely make these kinds of reactors the best tools for energy production in the second half of this century. (A.C.)

Instrumentation and control of future sodium cooled fast reactors - Design improvements

International Nuclear Information System (INIS)

Madhusoodanan, K.; Sakthivel, M.; Chellapandi, P.

2013-06-01

India's fast reactor program started with the 40 MWt Fast Breeder Test Reactor. 500 MWe Prototype Fast Breeder Reactor (PFBR) is currently under construction at Kalpakkam. Safety of PFBR is enhanced by improved design features of I and C system. Since the design of Instrumentation and control (I and C) of PFBR, considerable improvements in terms of advancement in technology and indigenization has taken place. Further improvements in I and C is proposed for solving many of the difficulties faced during the design and construction phases of PFBR. Design improvements proposed are covered in this paper which will make the implementation and maintenance of I and C of future SFRs easier. (authors)

Netherlands Interuniversity Reactor Institut

International Nuclear Information System (INIS)

1978-01-01

This is the annual report of the Interuniversity Reactor Institute in the Netherlands for the Academic Year 1977-78. Activities of the general committee, the daily committee and the scientific advice board are presented. Detailed reports of the scientific studies performed are given under five subjects - radiation physics, reactor physics, radiation chemistry, radiochemistry and radiation hygiene and dosimetry. Summarised reports of the various industrial groups are also presented. Training and education, publications and reports, courses, visits and cooperation with other institutes in the area of scientific research are mentioned. (C.F.)

Reactor Dosimetry State of the Art 2008

Science.gov (United States)

Voorbraak, Wim; Debarberis, Luigi; D'Hondt, Pierre; Wagemans, Jan

2009-08-01

. Williams, A. P. Ribaric and T. Schnauber. Agile high-fidelity MCNP model development techniques for rapid mechanical design iteration / J. A. Kulesza.Extension of Raptor-M3G to r-8-z geometry for use in reactor dosimetry applications / M. A. Hunter, G. Longoni and S. L. Anderson. In vessel exposure distributions evaluated with MCNP5 for Atucha II / J. M. Longhino, H. Blaumann and G. Zamonsky. Atucha I nuclear power plant azimutal ex-vessel flux profile evaluation / J. M. Longhino ... [et al.]. UFTR thermal column characterization and redesign for maximized thermal flux / C. Polit and A. Haghighat. Activation counter using liquid light-guide for dosimetry of neutron burst / M. Hayashi ... [et al.]. Control rod reactivity curves for the annular core research reactor / K. R. DePriest ... [et al.]. Specification of irradiation conditions in VVER-440 surveillance positions / V. Kochkin ... [et al.]. Simulations of Mg-Ar ionisation and TE-TE ionisation chambers with MCNPX in a straightforward gamma and beta irradiation field / S. Nievaart ... [et al.]. The change of austenitic stainless steel elements content in the inner parts of VVER-440 reactor during operation / V. Smutný, J. Hep and P. Novosad. Fast neutron environmental spectrometry using disk activation / G. Lövestam ... [et al.]. Optimization of the neutron activation detector location scheme for VVER-lOOO ex-vessel dosimetry / V. N. Bukanov ... [et al.]. Irradiation conditions for surveillance specimens located into plane containers installed in the WWER-lOOO reactor of unit 2 of the South-Ukrainian NPP / O. V. Grytsenko. V. N. Bukanov and S. M. Pugach. Conformity between LRO mock-ups and VVERS NPP RPV neutron flux attenuation / S. Belousov. Kr. Ilieva and D. Kirilova. FLUOLE: a new relevant experiment for PWR pressure vessel surveillance / D. Beretz ... [et al.]. Transport of neutrons and photons through the iron and water layers / M. J. Kost'ál ... [et al.]. Condition evaluation of spent nuclear fuel assemblies

A strategy to apply a graded approach to a new research reactor I and C design

International Nuclear Information System (INIS)

Suh, Yong Suk; Park, Jae Kwan; Kim, Taek Kyu; Bae, Sang Hoon; Baang, Dane; Kim, Young Ki

2012-01-01

A project for the development of a new research reactor (NRR) was launched by KAERI in 2012. It has two purposes: 1) providing a facility for radioisotope production, neutron transmutation doping, and semiconductor wafer doping, and 2) obtaining a standard model for exporting a research reactor (RR). The instrumentation and control (I and C) design should reveal an appropriate architecture for the NRR export. The adoption of a graded approach (GA) was taken into account to design the I and C and architecture. Although the GA for RRs is currently under development by the IAEA, it has been recommended and applied in many areas of nuclear facilities. The Canadian Nuclear Safety Commission allows for the use of a GA for RRs to meet the safety requirements. Germany applied the GA to a decommissioning project. It categorized the level of complexity of the decommissioning project using the GA. In the case of 10 C.F.R. Part 830 830.7, a contractor must use a GA to implement the requirements of the part, document the basis of the GA used, and submit that document to U.S. DOE. It mentions that a challenge is the inconsistent application of GA on DOE programs. RG 1.176 states that graded quality assurance brings benefits of resource allocation based on the safety significance of the items. The U.S. NRC also applied the GA to decommissioning small facilities. The NASA published a handbook for risk informed decision making that is conducted using a GA. ISATR67.04.09 2005 supplements ANSI/ISA.S67.04.01. 2000 and ISA RP67.04.02 2000 in determining the setpoint using a GA. The GA is defined as a risk informed approach that, without compromising safety, allows safety requirements to be implemented in such a way that the level of design, analysis, and documentation are commensurate with the potential risks of the reactor. The IAEA is developing a GA through DS351 and has recommended applying it to a reactor design according to power and hazarding level. Owing to the wide range of RR

A strategy to apply a graded approach to a new research reactor I and C design

Energy Technology Data Exchange (ETDEWEB)

Suh, Yong Suk; Park, Jae Kwan; Kim, Taek Kyu; Bae, Sang Hoon; Baang, Dane; Kim, Young Ki [KAERI, Daejeon (Korea, Republic of)

2012-10-15

A project for the development of a new research reactor (NRR) was launched by KAERI in 2012. It has two purposes: 1) providing a facility for radioisotope production, neutron transmutation doping, and semiconductor wafer doping, and 2) obtaining a standard model for exporting a research reactor (RR). The instrumentation and control (I and C) design should reveal an appropriate architecture for the NRR export. The adoption of a graded approach (GA) was taken into account to design the I and C and architecture. Although the GA for RRs is currently under development by the IAEA, it has been recommended and applied in many areas of nuclear facilities. The Canadian Nuclear Safety Commission allows for the use of a GA for RRs to meet the safety requirements. Germany applied the GA to a decommissioning project. It categorized the level of complexity of the decommissioning project using the GA. In the case of 10 C.F.R. Part 830 830.7, a contractor must use a GA to implement the requirements of the part, document the basis of the GA used, and submit that document to U.S. DOE. It mentions that a challenge is the inconsistent application of GA on DOE programs. RG 1.176 states that graded quality assurance brings benefits of resource allocation based on the safety significance of the items. The U.S. NRC also applied the GA to decommissioning small facilities. The NASA published a handbook for risk informed decision making that is conducted using a GA. ISATR67.04.09 2005 supplements ANSI/ISA.S67.04.01. 2000 and ISA RP67.04.02 2000 in determining the setpoint using a GA. The GA is defined as a risk informed approach that, without compromising safety, allows safety requirements to be implemented in such a way that the level of design, analysis, and documentation are commensurate with the potential risks of the reactor. The IAEA is developing a GA through DS351 and has recommended applying it to a reactor design according to power and hazarding level. Owing to the wide range of RR

Reactor core in FBR type reactor

International Nuclear Information System (INIS)

Masumi, Ryoji; Kawashima, Katsuyuki; Kurihara, Kunitoshi.

1989-01-01

In a reactor core in FBR type reactors, a portion of homogenous fuels constituting the homogenous reactor core is replaced with multi-region fuels in which the enrichment degree of fissile materials is lower nearer to the axial center. This enables to condition the composition such that a reactor core having neutron flux distribution either of a homogenous reactor core or a heterogenous reactor core has substantially identical reactivity. Accordingly, in the transfer from the homogenous reactor core to the axially heterogenous reactor core, the average reactivity in the reactor core is substantially equal in each of the cycles. Further, by replacing a portion of the homogenous fuels with a multi-region fuels, thereby increasing the heat generation near the axial center, it is possiable to reduce the linear power output in the regions above and below thereof and, in addition, to improve the thermal margin in the reactor core. (T.M.)

Generation IV reactors: economics

International Nuclear Information System (INIS)

Dupraz, B.; Bertel, E.

2003-01-01

The operating nuclear reactors were built over a short period: no more than 10 years and today their average age rounds 18 years. EDF (French electricity company) plans to renew its reactor park over a far longer period : 30 years from 2020 to 2050. According to EDF this objective implies 3 constraints: 1) a service life of 50 to 60 years for a significant part of the present operating reactors, 2) to be ready to built a generation 3+ unit in 2020 which infers the third constraint: 3) to launch the construction of an EPR (European pressurized reactor) prototype as soon as possible in order to have it operating in 2010. In this scheme, generation 4 reactor will benefit the feedback experience of generation 3 and will take over in 2030. Economic analysis is an important tool that has been used by the generation 4 international forum to select the likely future reactor systems. This analysis is based on 4 independent criteria: the basic construction cost, the construction time, the operation and maintenance costs and the fuel cycle cost. This analysis leads to the evaluation of the global cost of electricity generation and of the total investment required for each of the reactor system. The former defines the economic competitiveness in a de-regulated energy market while the latter is linked to the financial risk taken by the investor. It appears, within the limits of the assumptions and models used, that generation 4 reactors will be characterized by a better competitiveness and an equivalent financial risk when compared with the previous generation. (A.C.)

Wear plates control rod guide tubes top internal reactor vessel C. N. VANDELLOS II; Desgaste placas tubos guia barras de control interno superior vasija del reactor C.N. Vandellos II

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

The guide tubes for control rods forming part of the upper internals of the reactor vessel, its function is to guide the control rod to permit its insertion in the reactor core. These guide tubes are suspended from the upper support plate which are fixed by bolts and extending to the upper core plate which is fastened by clamping bolts (split pin) to prevent lateral displacement of the guide tubes, while allowing axial expansion.

Cumulative damage fatigue tests on nuclear reactor Zircaloy-2 fuel tubes at room temperature and 3000C

International Nuclear Information System (INIS)

Pandarinathan, P.R.; Vasudevan, P.

1980-01-01

Cumulative damage fatigue tests were conducted on the Zircaloy-2 fuel tubes at room temperature and 300 0 C on the modified Moore type, four-point-loaded, deflection-controlled, rotating bending fatigue testing machine. The cumulative cycle ratio at fracture for the Zircaloy-2 fuel tubes was found to depend on the sequence of loading, stress history, number of cycles of application of the pre-stress and the test temperature. A Hi-Lo type fatigue loading was found to be very much damaging at room temperature and this feature was not observed in the tests at 300 0 C. Results indicate significant differences in damage interaction and damage propagation under cumulative damage tests at room temperature and at 300 0 C. Block-loading fatigue tests are suggested as the best method to determine the life-time of Zircaloy-2 fuel tubes under random fatigue loading during their service in the reactor. (orig.)

Development of operation management database for research reactors

International Nuclear Information System (INIS)

Zhang Xinjun; Chen Wei; Yang Jun

2005-01-01

An Operation Database for Pulsed Reactor has been developed on the platform for Microsoft visual C++ 6.0. This database includes four function modules, fuel elements management, incident management, experiment management and file management. It is essential for reactor security and information management. (authors)

Ceramics as nuclear reactor fuels

International Nuclear Information System (INIS)

Reeve, K.D.

1975-01-01

Ceramics are widely accepted as nuclear reactor fuel materials, for both metal clad ceramic and all-ceramic fuel designs. Metal clad UO 2 is used commercially in large tonnages in five different power reactor designs. UO 2 pellets are made by familiar ceramic techniques but in a reactor they undergo complex thermal and chemical changes which must be thoroughly understood. Metal clad uranium-plutonium dioxide is used in present day fast breeder reactors, but may eventually be replaced by uranium-plutonium carbide or nitride. All-ceramic fuels, which are necessary for reactors operating above about 750 0 C, must incorporate one or more fission product retentive ceramic coatings. BeO-coated BeO matrix dispersion fuels and silicate glaze coated UO 2 -SiO 2 have been studied for specialised applications, but the only commercial high temperature fuel is based on graphite in which small fuel particles, each coated with vapour deposited carbon and silicon carbide, are dispersed. Ceramists have much to contribute to many aspects of fuel science and technology. (author)

Pellet bed reactor for nuclear thermal propelled vehicles

International Nuclear Information System (INIS)

El-Genk, M.; Morley, N.J.; Haloulakos, V.E.

1991-01-01

The Pellet Bed Reactor (PeBR) concept is capable of operating at a high power density of up to 3.0 kWt/cu cm and an exit hydrogen gas temperature of 3000 K. The nominal reactor thermal power is 1500 MW and the reactor core is 0.80 m in diameter and 1.3 m high. The nominal PeBR engine generates a thrust of approximately 315 kN at a specific impulse of 1000 s for a mission duration to Mars of 250 days requiring a total firing time of 170 minutes. Because of its low diameter-to-height ratio, PeBR has enough surface area for passive removal of the decay heat from the reactor core. The reactor is equipped with two independent shutdown mechanisms; 8-B4C safety rods and 26 BeO/B4C control drums; each system is capable of operating and scraming the reactor safely. Due to the absence of core internal support structures, the PeBR can be fueled and refueled in orbit using the vacuum of space. These unique features of the PeBR provide for safety during launch, simplicity of handling, deployment, and end-of-life disposal, and vehicle extended lifetime. 11 refs

Jules Horowitz reactor (RJH): its design

International Nuclear Information System (INIS)

Dupuy, J.P.

2002-01-01

This article presents the design of the new irradiation facility (Jules Horowitz reactor) that is planned to be built on the Cadarache site of Cea. 2 principles have been followed. The first one is based on a physical separation between the systems and activities related to the reactor and the experiments from one hand and the other systems and means dedicated to the treatment of the experimental devices before and after irradiation on the other hand. This first principle implies to build 2 buildings: the reactor building and the nuclear auxiliaries building. Inside the reactor building activities from the reactor itself are separated from those dedicated to experimentation. In order to maximize the efficiency of such a reactor, an important number of simultaneous experiments is expected, which will generate an endless flux of incoming and out-going experiments and as a consequence an important handling work between the different work posts. The second principle aims at easing any handling work without breaking the rules of confinement. The different storing pools, the water pits that lead to the 5 hot cells and the reactor tank will communicate through a water-filled canal that will link the 2 buildings. (A.C.)

An investigation of structural design methodology for HTGR reactor internals with ceramic materials (Contract research)

International Nuclear Information System (INIS)

Sumita, Junya; Shibata, Taiju; Nakagawa, Shigeaki; Iyoku, Tatsuo; Sawa, Kazuhiro

2008-03-01

To advance the performance and safety of HTGR, heat-resistant ceramic materials are expected to be used as reactor internals of HTGR. C/C composite and superplastic zirconia are the promising materials for this purpose. In order to use these new materials as reactor internals in HTGR, it is necessary to establish a structure design method to guarantee the structural integrity under environmental and load conditions. Therefore, C/C composite expected as reactor internals of VHTR is focused and an investigation on the structural design method applicable to the C/C composite and a basic applicability of the C/C composite to representative structures of HTGR were carried out in this report. As the results, it is found that the competing risk theory for the strength evaluation of the C/C composite is applicable to design method and C/C composite is expected to be used as reactor internals of HTGR. (author)

RAPID-L Highly Automated Fast Reactor Concept Without Any Control Rods (1) Reactor concept and plant dynamics analyses

International Nuclear Information System (INIS)

Kambe, Mitsuru; Tsunoda, Hirokazu; Mishima, Kaichiro; Iwamura, Takamichi

2002-01-01

The 200 kWe uranium-nitride fueled lithium cooled fast reactor concept 'RAPID-L' to achieve highly automated reactor operation has been demonstrated. RAPID-L is designed for Lunar base power system. It is one of the variants of RAPID (Refueling by All Pins Integrated Design), fast reactor concept, which enable quick and simplified refueling. The essential feature of RAPID concept is that the reactor core consists of an integrated fuel assembly instead of conventional fuel subassemblies. In this small size reactor core, 2700 fuel pins are integrated altogether and encased in a fuel cartridge. Refueling is conducted by replacing a fuel cartridge. The reactor can be operated without refueling for up to 10 years. Unique challenges in reactivity control systems design have been attempted in RAPID-L concept. The reactor has no control rod, but involves the following innovative reactivity control systems: Lithium Expansion Modules (LEM) for inherent reactivity feedback, Lithium Injection Modules (LIM) for inherent ultimate shutdown, and Lithium Release Modules (LRM) for automated reactor startup. All these systems adopt lithium-6 as a liquid poison instead of B 4 C rods. In combination with LEMs, LIMs and LRMs, RAPID-L can be operated without operator. This is the first reactor concept ever established in the world. This reactor concept is also applicable to the terrestrial fast reactors. In this paper, RAPID-L reactor concept and its transient characteristics are presented. (authors)

Modeling the effect in of criticality from changes in key parameters for small High Temperature Nuclear Reactor (U-BatteryTM) using MCNP4C

International Nuclear Information System (INIS)

Pauzi, A M

2013-01-01

The neutron transport code, Monte Carlo N-Particle (MCNP) which was wellkown as the gold standard in predicting nuclear reaction was used to model the small nuclear reactor core called U -battery TM, which was develop by the University of Manchester and Delft Institute of Technology. The paper introduces on the concept of modeling the small reactor core, a high temperature reactor (HTR) type with small coated TRISO fuel particle in graphite matrix using the MCNPv4C software. The criticality of the core were calculated using the software and analysed by changing key parameters such coolant type, fuel type and enrichment levels, cladding materials, and control rod type. The criticality results from the simulation were validated using the SCALE 5.1 software by [1] M Ding and J L Kloosterman, 2010. The data produced from these analyses would be used as part of the process of proposing initial core layout and a provisional list of materials for newly design reactor core. In the future, the criticality study would be continued with different core configurations and geometries.

Advanced design of fast reactor-membrane reformer (FR-MR)

International Nuclear Information System (INIS)

Tashimo, M.; Hori, I.; Yasuda, I.; Shirasaki, Y.; Kobayashi, K.

2004-01-01

A new plant concept of nuclear-produced hydrogen is being studied using a Fast Reactor-Membrane Reformer (FR-MR). The conventional steam methane reforming (SMR) system is a three-stage process. The first stage includes the reforming, the second contains a shift reaction and the third is the separation process. The reforming process requires high temperatures of 800 ∼ 900 deg C. The shift process generates heat and is performed at around 200 deg C. The membrane reforming has only one process stage under a nonequilibrium condition by removing H2 selectively through a membrane tube. The steam reforming temperature can be decreased from 800 deg C to 550 deg C, which is a remarkable benefit offered by the non-equilibrium condition. With this new technology, the reactor type can be changed from a High Temperature Gas-cooled Reactor (HTGR) to a Fast Reactor (FR). A Fast Reactor-Membrane Reformer (FR-MR) is composed of a nuclear plant and a hydrogen plant. The nuclear plant is a sodium-cooled Fast Reactor with mixed oxide fuel and with a power of 240 MWt. The heat transport system contains two circuits, the primary circuit and the secondary circuit. The membrane reformer units are set in the secondary circuit. The heat, supplied by the sodium, can produce 200 000 Nm 3 /h by 2 units. There are two types of membranes. One is made of Pd another one (advanced) is made of, for example V, or Nb. The technology for the Pd membrane is already established in a small scale. The non-Pd type is expected to improve the performance. (author)

Niobium carbide synthesis by solid-gas reaction using a rotating cylinder reactor

International Nuclear Information System (INIS)

Fontes, F.A.O.; Gomes, K.K.P.; Oliveira, S.A.; Souza, C.P.; Sousa, J.F.; Rio Grande do Norte Univ., Natal, RN

2004-01-01

A rotating cylinder reactor was designed for the synthesis of niobium carbide powders at 1173 K. Niobium carbide, NbC, was prepared by carbothermal reduction starting from commercial niobium pentoxide powders. The reactor was heated using a custom-made, two-part, hinged, electric furnace with programmable temperature control. The design and operational details of the reactor are presented. The longitudinal temperature gradient inside the reactor was determined. Total reaction time was monitored by a gas chromatograph equipped with an FID detector for determination of methane concentrations. The results show that time of reaction depended on rotation speed. NbC was also prepared in a static-bed alumina reactor using the same conditions as in the previous case. The niobium carbide powders were characterized by X-ray diffraction and compared with commercially available products. Morphological, particle size distribution and surface area analyses were obtained using SEM, LDPS and BET, respectively. Therefore, the present study offers a significant technological contribution to the synthesis of NbC powders in a rotating cylinder reactor. (author)

Who needs a small reactor?

International Nuclear Information System (INIS)

Wood, Janet.

1991-01-01

The opportunities and problems facing small reactors were debated at the Delhi seminar. It was established that these were markets where small reactors, producing heat as well as electricity, might be of use. Small combined heat and power reactors would be more useful in district heating than would large reactors, as their optimum heat production is in line with current district heating schemes. Most process heat requirements are below 900 o C and so may be provided by small nuclear plants. Several areas in electricity supply where small and medium sized reactors could find a market were also identified. Despite good reasons for favouring nuclear plants in these markets, such as no production of carbon dioxide, no need to use expensive oil or other scarce fossil fuels and flexibility, these are, however, disincentives to potential buyers. While serial production would decrease plant costs, the lead plants would bear heavy financial risks. Currently too many options in plant design make it difficult to present the advantages of small reactor technology. Siting reactors near centres of population would be problematical. The disposal of spent fuel and radioactive wastes would create problems in developing or non-nuclear countries. Over and above all these problems, however, was that of public acceptance. Some ways of overcoming these disincentives were discussed. (author)

Nanocrystalline SiC and Ti₃SiC₂ Alloys for Reactor Materials: Diffusion of Fission Product Surrogates

Energy Technology Data Exchange (ETDEWEB)

Henager, Charles H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jiang, Weilin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-11-01

MAX phases, such as titanium silicon carbide (Ti₃SiC₂), have a unique combination of both metallic and ceramic properties, which make them attractive for potential nuclear applications. Ti₃SiC₂ has been suggested in the literature as a possible fuel cladding material. Prior to the application, it is necessary to investigate diffusivities of fission products in the ternary compound at elevated temperatures. This study attempts to obtain relevant data and make an initial assessment for Ti₃SiC₂. Ion implantation was used to introduce fission product surrogates (Ag and Cs) and a noble metal (Au) in Ti₃SiC₂, SiC, and a dual-phase nanocomposite of Ti₃SiC₂/SiC synthesized at PNNL. Thermal annealing and in-situ Rutherford backscattering spectrometry (RBS) were employed to study the diffusivity of the various implanted species in the materials. In-situ RBS study of Ti₃SiC₂ implanted with Au ions at various temperatures was also performed. The experimental results indicate that the implanted Ag in SiC is immobile up to the highest temperature (1273 K) applied in this study; in contrast, significant out-diffusion of both Ag and Au in MAX phase Ti₃SiC₂ occurs during ion implantation at 873 K. Cs in Ti₃SiC₂ is found to diffuse during post-irradiation annealing at 973 K, and noticeable Cs release from the sample is observed. This study may suggest caution in using Ti₃SiC₂ as a fuel cladding material for advanced nuclear reactors operating at very high temperatures. Further studies of the related materials are recommended.

Chemical reaction engineering aspects of a rotary reactor for carbothermal synthesis of SiC

NARCIS (Netherlands)

van Dijen, F.K.; Metselaar, R.

1989-01-01

Heat transfer in a rotary reactor is described for a reactor consisting of a graphite tube with graphite heating elements, and operating at temperatures between 1773 and 2273 K. Under those conditions heat transfer is very good due to radiation and the high thermal conductivity of graphite. An

The Development of a Hybrid-Type Radiation Detector with SiC for a Reactor Robot

International Nuclear Information System (INIS)

Lee, Nam Ho; Cho, Jai Wan; Kim, Seung Ho

2005-01-01

For a robot working in a harsh environment such as a nuclear reactor environment or a space environment, requirements of on-board radiation detectors are not the same as those for environments around human. SiC devices with the wide band-gap are less dependent on temperature than Si counterparts and the can be the better candidate for the high radiation environment. With this background, radiation performance of a commercial SiC detector in a Co-60 gamma-ray environment has been evaluated. In addition to the SiC detector, a MOSFET (Metal Oxide Semiconductor Field Effect Transistor) detector has been incorporated as a backup. With this MOSFET sensor the dosimeter can keep its radiation exposure history even with loss of power. It is not only a redundant feature but also a diverse feature. The dosimetry module can be attached to mobile robot for high radiation environment was developed. This module has both SiC diode and pMOSFET mentioned above. The monitoring program which receives the radiation information from them and gives out the alarm signal when the difference of the two values from them is over the preset level was constructed. Because both the SiC pulse-type detector and the MOSFET dosimeter are small and light weight, they can be easily accommodated on a small printcircuit board for a tight space on a robot arm or for a small spacecraft

Reactor core and initially loaded reactor core of nuclear reactor

International Nuclear Information System (INIS)

Koyama, Jun-ichi; Aoyama, Motoo.

1989-01-01

In BWR type reactors, improvement for the reactor shutdown margin is an important characteristic condition togehter with power distribution flattening . However, in the reactor core at high burnup degree, the reactor shutdown margin is different depending on the radial position of the reactor core. That is , the reactor shutdown margin is smaller in the outer peripheral region than in the central region of the reactor core. In view of the above, the reactor core is divided radially into a central region and as outer region. The amount of fissionable material of first fuel assemblies newly loaded in the outer region is made less than the amount of the fissionable material of second fuel assemblies newly loaded in the central region, to thereby improve the reactor shutdown margin in the outer region. Further, the ratio between the amount of the fissionable material in the upper region and that of the fissionable material in the lower portion of the first fuel assemblies is made smaller than the ratio between the amount of the fissionable material in the upper region and that of the fissionable material in the lower region of the second fuel assemblies, to thereby obtain a sufficient thermal margin in the central region. (K.M.)

Proceedings of the 6. National Meeting of Reactor Physics and Thermohydraulic

International Nuclear Information System (INIS)

1986-01-01

The proceedings of the 6. National Meeting of Reactor Physics and Thermohydraulic - 6. ENFIR - allow to evaluate the present status of development in reactor physics and thermohydraulic fields. The mathematical models and methods for calculating neutronic of nuclear reactors, safety reactor analysis, measuring methods of neutronic parameters, computerized simulation of accidents, transients and thermohydraulic analysis are presented. (M.C.K.) [pt

Homogenous reactor, elaborations, not released up to end

International Nuclear Information System (INIS)

Takibayev, Zh.S.

2002-01-01

because they are situated outside of reactor core and so they are exposed less to neutron irradiation. If nuclear reactor work on thermal neutrons there will be inevitable diminution of efficiency of lagging neutrons as some their part appears out site an reactor core. In this problem there is a great hope on development of nuclear reactors elaboration with liquid metal fuel, in which fast neutrons are used in the field of energetic spectrum energy nearby 1 MeV. In other words there is no reason to reduce neutrons up the thermal ones in such reactors. So there will not any moderators in reactor core. Future will show whether hope justified for the development of fast breeder reactors with homogenous, for example, liquid metal and salt liquid fuel. As the analysis shows it is not excluded that the best and simple fuel in such reactors would be suspension consisted of UO 2 as fine solid powder and metallic liquid Bi(52.5 %)+ Pb(32 %) + Sn(15.5 %). This dredge can be both fuel and coolant with melting temperature t melt ∼100 deg. C and density ρ∼10 g/cm 3 . The last figure is very important as the density of all suspension coincides nearly with density UO 2 which is equal to 10.97 g/cm 3 . So we can expect that the exfoliation effect in suspension will be considerably decreased. Besides, because of low melting temperature (∼100 deg. C) of metallic liquid, in which fine powder (UO 2 ) is weighed equally, it is considerably easier to work with such fuel than to heat up to high temperature solution or liquid metal as it is supposed in many other works. Any liquid fuel in homogeneous reactor, for example, salt liquid or simply liquid metal must meet requirements: to possess thermal and radiation stability; pressure of saturated vapor at higher temperatures (∼1000 deg. C) must be small ( 3 . Suspension from fine powder of U C and liquid metal bath (Bi + Pb + Sn), which density is nearly 10 g/cm 3 can take the second place as fuel for future homogeneous reactor. However

New ceramics for nuclear industry. Case of fission and fusion reactors

International Nuclear Information System (INIS)

Yvars, M.

1979-10-01

The ceramics used in the nuclear field are described as is their behaviour under radiation. 1) Power reactors - nuclear fission. Ceramics enter into the fabrication of nuclear fuels: oxides, carbides, uranium or plutonium nitrides or oxy-nitrides. Silicon carbide SiC is used for preparing the fuels of helium cooled high temperature reactors. Its use is foreseen in the design of gas high temperature gas thermal exchangers, as is silicon nitride (Si 3 N 4 ). In the materials for safety or control rods, the intense neutron flows induce nuclear reactions which increase the temperature of the neutron absorbing material. Boron carbide B 4 C, rare earth oxides Ln 2 O 3 , or B 4 C-Cu or B 4 C-Al cermets are employed. Burnable poison materials are formed of Al 2 O 3 -B 4 C or Al 2 O 3 -Ln 2 O 3 cermets. The moderators of thermal neutron reactors are in high purety polycrystalline graphite. For the thermal insulation of reactor vessels and jackets, honeycomb ceramics are used as well as ceramic fibres on an increasing scale (kaolin, alumina and other fibres). 2) fusion reactors (Tokomak). These require refractory materials with a low atomic number. Carbon fibres, boron carbide, some borons (Al B 12 ), silicon nitrides and oxy-nitrides and high density alumina are the substances considered [fr

High temperature helium-cooled fast reactor (HTHFR)

International Nuclear Information System (INIS)

Karam, R.A.; Blaylock, Dwayne; Burgett, Eric; Mostafa Ghiaasiaan, S.; Hertel, Nolan

2006-01-01

Scoping calculations have been performed for a very high temperature (1000 o C) helium-cooled fast reactor involving two distinct options: (1) using graphite foam into which UC (12% enrichment) is embedded into a matrix comprising UC and graphite foam molded into hexagonal building blocks and encapsulated with a SiC shell covering all surfaces, and (2) using UC only (also 12% enrichment) molded into the same shape and size as the foam-UC matrix in option 1. Both options use the same basic hexagonal fuel matrix blocks to form the core and reflector. The reflector contains natural uranium only. Both options use 50 μm SiC as a containment shell for fission product retention within each hexagonal block. The calculations show that the option using foam (option 1) would produce a reactor that can operate continuously for at least 25 years without ever adding or removing any fuel from the reactor. The calculations show further that the UC only option (option 2) can operate continually for 50 years without ever adding or removing fuel from the reactor. Doppler and loss of coolant reactivity coefficients were calculated. The Doppler coefficient is negative and much larger than the loss of coolant coefficient, which was very small and positive. Additional progress on and development of the two concepts are continuing

The post irradiation examination of a sphere-pac (UPu)C fuel pin irradiated in the BR-2 reactor (MFBS 7 experiment)

International Nuclear Information System (INIS)

Smith, L.; Aerne, E.T.; Buergisser, B.; Flueckiger, U.; Hofer, R.; Petrik, F.

1979-09-01

A pin fuelled with Swiss made (UPu)C microspheres has been successfully irradiated to a peak burn-up of 6% fima in the Belgian BR2 Reactor. The pin, rated up to 95 kW/m, was intact after irradiation and exhibited a peak strain of just over 0.5%. The results of the post irradiation examination are reported. (Auth.)

Secret high-temperature reactor concept for inertial fusion

International Nuclear Information System (INIS)

Monsler, M.J.; Meier, W.R.

1983-01-01

The goal of our SCEPTRE project was to create an advanced second-generation inertial fusion reactor that offers the potential for either of the following: (1) generating electricity at 50% efficiency, (2) providing high temperature heat (850 0 C) for hydrogen production, or (3) producing fissile fuel for light-water reactors. We have found that these applications are conceptually feasible with a reactor that is intrinsically free of the hazards of catastrophic fire or tritium release

International Working Group on Fast Reactors Sixth Annual Meeting. Summary Report

International Nuclear Information System (INIS)

1973-01-01

The Agenda of the Meeting was as follows: 1. Review of IWGFR Activities - 1a. Approval of the minutes of the Fifth IWGFR Meeting. 1b. Report by Scientific Secretary regarding the activities of the Group. 2. Comments on National Programmes on Fast Breeder Reactors. 3. International Coordination of the Schedule for Major Fast Reactor Meetings and other major international meetings having a predominant fast reactor interest. 4. Consideration of Conferences on Fast Reactors. 4a. IAEA Symposium on Fuel and Fuel Elements for Fast Reactors, Brussels, Belgium 2-6 July 1973. 4b. International Symposium on Physics of Fast Reactors, Tokyo, Japan, 16 to 23 October 1973. 4c. International Conference on Fast Reactor Power Stations, London, UK, 11 to 14 March 1974 . 4d. Suggestions of the IWGFR members on other conferences. 5. Consideration of a Schedule for Specialists' Meetings in 1973-74. 6. Other Business - 6a. First-aid in Sodium Burns. 6b. Principles of Good Practice for Safe Operation of Sodium Circuits. 6c. Bibliography on Fast Reactors. 7. The Date and Place of the Seventh Annual Meeting of the IWGFR

Activation and waste disposal of the TITAN RFP [reversed-field-pinch] reactors

International Nuclear Information System (INIS)

Cheng, E.T.; Conn, R.W.

1988-01-01

The TITAN-I lithium self-cooled and TITAN-II aqueous lithium nitrate solution-cooled fusion reactors are based on the reversed-field-pinch (RFP) toroidal confinement concept and operate at high power density with an 18.1 MW/m 2 neutron wall loading. These designs were analyzed to study the activation and waste disposal aspects of such high-power density reactors. It was found that because of the use of V-3Ti-1Si (TITAN-I) and reduced activation ferritic steel (TITAN-II) as structural alloys for the first wall, blanket, reflector, and shield components, all the TITAN components except the divertor collector plates can be classified as shallow-land burial (10CFR61 Class C or better) nuclear waste for disposal, provided that the impurity elements, niobium and molybdenum, can be controlled below about 1 and 0.3 appm levels, respectively. The average annual disposal masses were estimated to be 150 and 96 tonnes, respectively, for the 1,000 MW TITAN-I and TITAN-II reactors. This corresponds to about 11% of the total mass in the fusion power core of both reactors. The divertor collector plates are fabricated with tungsten because of its low particle sputtering properties. These divertor collector plates in the TITAN-I reactor will be qualified as Class C waste after 18.1 MW-y/m 2 operation. The waste disposal rating of the divertor collector plates in the TITAN-II reactor, however, is estimated to be a factor of 4 higher than allowed for Class C disposal, because of the soft neutron spectrum in the beryllium environment. The annual disposal mass of this non-Class C waste is 0.35 tons, about 0.04% of the average annual discharge mass for the TITAN-II reactor. An additional 74 m 3 annual discharge of Class C waste containing 14 C may be needed for the TITAN-II reactor because of the use of nitrate salt in the aqueous coolant as the tritium breeder. 13 refs., 6 tabs

Nuclear reactor physics course for reactor operators

International Nuclear Information System (INIS)

Baeten, P.

2006-01-01

The education and training of nuclear reactor operators is important to guarantee the safe operation of present and future nuclear reactors. Therefore, a course on basic 'Nuclear reactor physics' in the initial and continuous training of reactor operators has proven to be indispensable. In most countries, such training also results from the direct request from the safety authorities to assure the high level of competence of the staff in nuclear reactors. The aim of the basic course on 'Nuclear Reactor Physics for reactor operators' is to provide the reactor operators with a basic understanding of the main concepts relevant to nuclear reactors. Seen the education level of the participants, mathematical derivations are simplified and reduced to a minimum, but not completely eliminated

Reactor core of FBR type reactor

International Nuclear Information System (INIS)

Hayashi, Hideyuki; Ichimiya, Masakazu.

1994-01-01

A reactor core is a homogeneous reactor core divided into two regions of an inner reactor core region at the center and an outer reactor core region surrounding the outside of the inner reactor core region. In this case, the inner reactor core region has a lower plutonium enrichment degree and less amount of neutron leakage in the radial direction, and the outer reactor core region has higher plutonium enrichment degree and greater amount of neutron leakage in the radial direction. Moderator materials containing hydrogen are added only to the inner reactor core fuels in the inner reactor core region. Pins loaded with the fuels with addition of the moderator materials are inserted at a ratio of from 3 to 10% of the total number of the fuel pins. The moderator materials containing hydrogen comprise zirconium hydride, titanium hydride, or calcium hydride. With such a constitution, fluctuation of the power distribution in the radial direction along with burning is suppressed. In addition, an absolute value of the Doppler coefficient can be increased, and a temperature coefficient of coolants can be reduced. (I.N.)

Safe Management Of Fast Reactors: Towards Sustainability

International Nuclear Information System (INIS)

Dreimanis, Andrejs

2015-01-01

An interdisciplinary systemic approach to socio-technical optimization of nuclear energy management is proposed, by recognizing a) the rising requirements to nuclear safety being realized using fast reactors (FR), b) the actuality to maintain and educate qualified workforce for fast reactors, c) the reactor safety and public awareness as the keystones for improving attitude to implement novel reactors. Knowledge management and informational support firstly is needed in: 1) technical issues: a) nuclear energy safety and reliability, b) to develop safe and economic technologies; 2) societal issues: a) general nuclear awareness, b) personnel education and training, c) reliable staff renascence, public education, stakeholder involvement, e).risk management. The key methodology - the principles being capable to manage knowledge and information issues: 1) a self-organization concept, 2) the principle of the requisite variety. As a primary source of growth of internal variety is considered information and knowledge. Following questions are analyzed indicating the ways of further development: a) threats in peaceful use of nuclear energy, b) basic features of nuclear risks, including terrorism, c) human resource development: basic tasks and instruments, d) safety improvements in technologies, e) advanced research and nuclear awareness improvement There is shown: public education, social learning and the use of mass media are efficient mechanisms forming a knowledge-creating community thereby reasoning to facilitate solution of key socio-technical nuclear issues: a) public acceptance of novel nuclear objects, b) promotion of adequate risk perception, and c) elevation of nuclear safety level and adequate risk management resulting in energetic and ecological sustainability. (author)

Cooling Performance Analysis of ThePrimary Cooling System ReactorTRIGA-2000Bandung

Science.gov (United States)

Irianto, I. D.; Dibyo, S.; Bakhri, S.; Sunaryo, G. R.

2018-02-01

The conversion of reactor fuel type will affect the heat transfer process resulting from the reactor core to the cooling system. This conversion resulted in changes to the cooling system performance and parameters of operation and design of key components of the reactor coolant system, especially the primary cooling system. The calculation of the operating parameters of the primary cooling system of the reactor TRIGA 2000 Bandung is done using ChemCad Package 6.1.4. The calculation of the operating parameters of the cooling system is based on mass and energy balance in each coolant flow path and unit components. Output calculation is the temperature, pressure and flow rate of the coolant used in the cooling process. The results of a simulation of the performance of the primary cooling system indicate that if the primary cooling system operates with a single pump or coolant mass flow rate of 60 kg/s, it will obtain the reactor inlet and outlet temperature respectively 32.2 °C and 40.2 °C. But if it operates with two pumps with a capacity of 75% or coolant mass flow rate of 90 kg/s, the obtained reactor inlet, and outlet temperature respectively 32.9 °C and 38.2 °C. Both models are qualified as a primary coolant for the primary coolant temperature is still below the permitted limit is 49.0 °C.

Nuclear reactors

International Nuclear Information System (INIS)

Barre, Bertrand

2015-10-01

After some remarks on the nuclear fuel, on the chain reaction control, on fuel loading and unloading, this article proposes descriptions of the design, principles and operations of different types of nuclear reactors as well as comments on their presence and use in different countries: pressurized water reactors (design of the primary and secondary circuits, volume and chemistry control, backup injection circuits), boiling water reactors, heavy water reactors, graphite and boiling water reactors, graphite-gas reactors, fast breeder reactors, and fourth generation reactors (definition, fast breeding). For these last ones, six concepts are presented: sodium-cooled fast reactor, lead-cooled fast reactor, gas-cooled fast reactor, high temperature gas-cooled reactor, supercritical water-cooled reactor, and molten salt reactor

Development of 'low activation superconducting wire' for an advanced fusion reactor

International Nuclear Information System (INIS)

Hishinuma, Y.; Yamada, S.; Sagara, A.; Kikuchi, A.; Takeuchi, T.; Matsuda, K.; Taniguchi, H.

2011-01-01

In the D-T burning plasma reactor beyond ITER such as DEMO and fusion power plants assuming the steady-state and long time operation, it will be necessary to consider carefully induced radioactivity and neutron irradiation properties on the all components for fusion reactors. The decay time of the induced radioactivity can control the schedule and scenarios of the maintenance and shutdown on the fusion reactor. V 3 Ga and MgB 2 compound have shorter decay time within 1 years and they will be desirable as a candidate material to realize 'low activation and high magnetic field superconducting magnet' for advanced fusion reactor. However, it is well known that J c -B properties of V 3 Ga and MgB 2 wires are lower than that of the Nb-based A15 compound wires, so the J c -B enhancements on the V 3 Ga and MgB 2 wires are required in order to apply for an advanced fusion reactor. We approached and succeeded to developing the new process in order to improve J c properties of V 3 Ga and MgB 2 wires. In this paper, the recent activities for the J c improvements and detailed new process in V 3 Ga and MgB 2 wires are investigated. (author)

Twenty years of Triga Mark I reactor use

International Nuclear Information System (INIS)

Stasiulevicius, R.; Maretti Junior, F.

1981-01-01

This work is a report on the 20 years of activities of the Triga Mark I, research reactor located in Belo Horizonte, Brazil. It contains also a list of publications, details of operation and improvements introduced in the reactor as well as some perspectives for its future. (A.C.A.S.)

Development of metal-carbon eutectic cells for application as high temperature reference points in nuclear reactor severe accident tests: Results on the Fe-C, Co-C, Ti-C and Ru-C alloys' melting/freezing transformation temperature under electromagnetic induction heating

International Nuclear Information System (INIS)

Parga, Clemente J.; Journeau, Christophe; Parga, Clemente J.; Tokuhiro, Akira

2012-01-01

With the aim of reducing the high temperature measurement uncertainty of nuclear reactor severe accident experimental tests at the PLINIUS platform in Cadarache Research Centre, France, a variety of graphite cells containing a metal-carbon eutectic mix have been tested to assess the melting/freezing temperature reproducibility and their feasibility as calibration cells for thermometers. The eutectic cells have been thermally cycled in an induction furnace to assess the effect of heating/cooling rate, metal purity, graphite crucible design, and binary system constituents on the eutectic transformation temperature. A bi-chromatic pyrometer was used to perform temperature measurements in the graphite cell black cavity containing the metal-carbon eutectic mix. The eutectic points analyzed are all over 1100 C and cover an almost thousand degree span, i.e. from the Fe-Fe 3 C to the Ru-C eutectic. The induction heating permitted the attainment of heating and cooling rates of over 200 C/min under an inert atmosphere. The conducted tests allowed the determination of general trends and peculiarities of the solid. liquid transformation temperature under non-equilibrium and non-steady-state conditions of a variety of eutectic alloys (Fe-C, Co-C, Ti-C and Ru-C binary systems). (authors)

Effect of post-digestion temperature on serial CSTR biogas reactor performance

DEFF Research Database (Denmark)

Boe, Kanokwan; Karakashev, Dimitar Borisov; Trably, Eric

2009-01-01

The effect of post-digestion temperature on a lab-scale serial continuous-flow stirred tank reactor (CSTR) system performance was investigated. The system consisted of a main reactor operated at 55 degrees C with hydraulic retention time (HRT) of 15 days followed by post-digestion reactors with HRT...

First conceptual design of the experimental multi-purpose high temperature reactor

Energy Technology Data Exchange (ETDEWEB)

Tsunoda, T [Fuji Electric Co. Ltd., Tokyo (Japan)

1976-02-01

A part of the multi-purpose high temperature reactor (VHTR) was designed by the First Atomic Power Industry Group (FAPIG). Both Fuji Electric Co., Ltd. and Kawasaki Heavy Industries, Ltd. of the FAPIG group took charge of the design of main parts of the reactor Kobe Steel, Ltd., Ebara Manufacturing Co., Ltd., Shimizu Construction Co., Ltd. and the Nuclear Fuel Corp. have associated with this group. The reactor system includes a nuclear reactor and two cooling loops provided through intermediate heat exchangers in order to utilize the heat of helium gas delivered from the reactor outlet at 1,000 deg C. One is a reformer loop to produce the reducing gas for steel manufacture. The other is a testing loop for a reducing gas heater and a gas turbine. These loops transfer heat of about 25 MW at 930 deg C at rated capacity. The reformer can supply the reducing gas equivalent to the production of 100 tons per day sponge iron. A housing of the reactor is composed of a primary steel container, internal concrete and a secondary container made of reinforced concrete. The construction is based on the following principles. (1) For the very high temperature portion at 1,000 deg C, a non-metallic material such as graphite should be used. (2) The metallic construction shall be cooled with return gas below 400 deg C. (3) The steel pressure vessel shall be employed. (4) The design shall be based on the existing gas furnace.

Fast reactors: the future of nuclear energy

International Nuclear Information System (INIS)

Carvalho, H.G. de.

1988-08-01

The main problems to be solved for FBR type reactors become viable economically, presenting the research programs of Europe, United States of America, Japan and Brazil are described. The cooperations between interested countries for improving FBR type reactors, and the financial and human resources necessaries for the development of programs, are evaluated. The fuel cycle is also analysed. (M.C.K.) [pt

Flow analysis in a supercritical water oxidation reactor

International Nuclear Information System (INIS)

Oh, C.H.; Kochan, R.J.; Beller, J.M.

1996-01-01

Supercritical water oxidation (SCWO), also known as hydrothermal oxidation (HTO), involves the oxidation of hazardous waste at conditions of elevated temperature and pressure (e.g., 500 C--600 C and 234.4 bar) in the presence of approximately 90% of water and a 10% to 20% excess amount of oxidant over the stoichiometric requirement. Under these conditions, organic compounds are completely miscible with supercritical water, oxygen and nitrogen, and are rapidly oxidized to carbon dioxide and water. The essential part of the process is the reactor. Many reactor designs such as tubular, vertical vessel, and transpiring wall type have been proposed, patented, and tested at both bench and pilot scales. These designs and performances need to be scaled up to a waste throughput 10--100 times that currently being tested. Scaling of this magnitude will be done by creating a numerical thermal-hydraulic model of the smaller reactor for which test data is available, validating the model against the available data, and then using the validated model to investigate the larger reactor performance. This paper presents a flow analysis of the MODAR bench scale reactor (vertical vessel type). These results will help in the design of the reactor in an efficient manner because the flow mixing coupled with chemical kinetics eventually affects the process destruction efficiency

Reactor Vessel and Reactor Vessel Internals Segmentation at Zion Nuclear Power Station - 13230

Energy Technology Data Exchange (ETDEWEB)

Cooke, Conrad; Spann, Holger [Siempelkamp Nuclear Services: 5229 Sunset Blvd., (Suite M), West Columbia, SC, 29169 (United States)

2013-07-01

Zion Nuclear Power Station (ZNPS) is a dual-unit Pressurized Water Reactor (PWR) nuclear power plant located on the Lake Michigan shoreline, in the city of Zion, Illinois approximately 64 km (40 miles) north of Chicago, Illinois and 67 km (42 miles) south of Milwaukee, Wisconsin. Each PWR is of the Westinghouse design and had a generation capacity of 1040 MW. Exelon Corporation operated both reactors with the first unit starting production of power in 1973 and the second unit coming on line in 1974. The operation of both reactors ceased in 1996/1997. In 2010 the Nuclear Regulatory Commission approved the transfer of Exelon Corporation's license to ZionSolutions, the Long Term Stewardship subsidiary of EnergySolutions responsible for the decommissioning of ZNPS. In October 2010, ZionSolutions awarded Siempelkamp Nuclear Services, Inc. (SNS) the contract to plan, segment, remove, and package both reactor vessels and their respective internals. This presentation discusses the tools employed by SNS to remove and segment the Reactor Vessel Internals (RVI) and Reactor Vessels (RV) and conveys the recent progress. SNS's mechanical segmentation tooling includes the C-HORCE (Circumferential Hydraulically Operated Cutting Equipment), BMT (Bolt Milling Tool), FaST (Former Attachment Severing Tool) and the VRS (Volume Reduction Station). Thermal segmentation of the reactor vessels will be accomplished using an Oxygen- Propane cutting system. The tools for internals segmentation were designed by SNS using their experience from other successful reactor and large component decommissioning and demolition (D and D) projects in the US. All of the designs allow for the mechanical segmentation of the internals remotely in the water-filled reactor cavities. The C-HORCE is designed to saw seven circumferential cuts through the Core Barrel and Thermal Shield walls with individual thicknesses up to 100 mm (4 inches). The BMT is designed to remove the bolts that fasten the Baffle

Carbon-14 in reactor plant water

International Nuclear Information System (INIS)

Knowles, G.K.

1979-01-01

The method for the analysis of 14 C in reactor plant water and various waste streams previously used at the Idaho National Engineering Laboratory has been shown to be ineffective for samples which contain organic compounds. The previous method consisted of acidification and refluxing of the sample, precipitation of the liberated CO 2 , and subsequent analysis by the liquid scintillation method. The method was simple but it did not convert all compounds containing 14 C in the sample to CO 2 . The new method, while it is based on the previous method, has been improved by employing a strong oxidant, potassium persulfate and silver nitrate, for more complete oxidation of the organics to CO 2 . The new method yields 14 C values that have typically been one to two orders of magnitude higher than the values obtained using the former method. This indicates that most of the 14 C present in the current reactor water samples being analyzed is associated with trace amounts of organics

Assessment of very high-temperature reactors in process application. Appendix I. Evaluation of the reactor system

International Nuclear Information System (INIS)

Jones, J.E. Jr.; Spiewak, I.

1976-12-01

In April 1974, the U.S. Atomic Energy Commission [now the Energy Research and Development Administration (ERDA)] authorized General Atomic Company, General Electric Company, and Westinghouse Electric Corp., Astronuclear Laboratory, to assess the available technology for producing heat using very high-temperature nuclear reactors. An evaulation of these studies and of the technical and economic potential of very high-temperature reactors (VHTR) is presented. The VHTR is a helium-cooled graphite-moderated reactor. The concepts and technology are evaluated for producing process stream temperatures of 649, 760, 871, 982, and 1093 0 C (1200, 1400, 1600, 1800, and 2000 0 F). There are a number of large industrial process heat applications that could utilize the VHTR

Gas turbine modular helium reactor in cogeneration; Turbina de gas reactor modular con helio en cogeneracion

Energy Technology Data Exchange (ETDEWEB)

Leon de los Santos, G. [UNAM, Facultad de Ingenieria, Division de Ingenieria Electrica, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Mexico, D. F. (Mexico)], e-mail: tesgleon@gmail.com

2009-10-15

This work carries out the thermal evaluation from the conversion of nuclear energy to electric power and process heat, through to implement an outline gas turbine modular helium reactor in cogeneration. Modeling and simulating with software Thermo flex of Thermo flow the performance parameters, based on a nuclear power plant constituted by an helium cooled reactor and helium gas turbine with three compression stages, two of inter cooling and one regeneration stage; more four heat recovery process, generating two pressure levels of overheat vapor, a pressure level of saturated vapor and one of hot water, with energetic characteristics to be able to give supply to a very wide gamma of industrial processes. Obtaining a relationship heat electricity of 0.52 and efficiency of net cogeneration of 54.28%, 70.2 MW net electric, 36.6 MW net thermal with 35% of condensed return to 30 C; for a supplied power by reactor of 196.7 MW; and with conditions in advanced gas turbine of 850 C and 7.06 Mpa, assembly in a shaft, inter cooling and heat recovery in cogeneration. (Author)

Safety assessment of Department of Energy nuclear reactors

International Nuclear Information System (INIS)

1981-03-01

One of the first tasks of the NFPQT Committee was to determine which DOE reactors would be assessed. The Committee determined that in view of the limited time available to conduct the assessment, 13 DOE reactors were of such size (physical, power or fission product inventory) to warrant review. This determination was approved by the Under Secretary. A decision was also made in the cases of three weapons material production reactors, C, K and P, to concentrate on the K reactor only, since all three are of the same basic design, have the same operating features, are all at the same site, and are all operated by the same contractor. The assessment was accomplished in the following ways: reviewing the results of assessments conducted by the DOE organizations with reactor safety responsibilities, which were undertaken in compliance with the request of the various program directors; reviewing selected documents that were requested by the Committee and assembled at DOE Headquarters; interviewing DOE Headquarters and Field Office personnel; and conducting on-site reviews of four reactors located at four different sites. The four reactors for on-site reviews were: Advanced Test Reactor (ATR); K Production Reactor; High Flux Beam Reactor (HFBR); and High Flux Isotope Reactor (HFIR). Specific findings and recommendations from the assessment are presented

Plasma nitriding monitoring reactor: A model reactor for studying plasma nitriding processes using an active screen

Science.gov (United States)

Hamann, S.; Börner, K.; Burlacov, I.; Spies, H.-J.; Strämke, M.; Strämke, S.; Röpcke, J.

2015-12-01

A laboratory scale plasma nitriding monitoring reactor (PLANIMOR) has been designed to study the basics of active screen plasma nitriding (ASPN) processes. PLANIMOR consists of a tube reactor vessel, made of borosilicate glass, enabling optical emission spectroscopy (OES) and infrared absorption spectroscopy. The linear setup of the electrode system of the reactor has the advantages to apply the diagnostic approaches on each part of the plasma process, separately. Furthermore, possible changes of the electrical field and of the heat generation, as they could appear in down-scaled cylindrical ASPN reactors, are avoided. PLANIMOR has been used for the nitriding of steel samples, achieving similar results as in an industrial scale ASPN reactor. A compact spectrometer using an external cavity quantum cascade laser combined with an optical multi-pass cell has been applied for the detection of molecular reaction products. This allowed the determination of the concentrations of four stable molecular species (CH4, C2H2, HCN, and NH3). With the help of OES, the rotational temperature of the screen plasma could be determined.

Plasma nitriding monitoring reactor: A model reactor for studying plasma nitriding processes using an active screen

International Nuclear Information System (INIS)

Hamann, S.; Röpcke, J.; Börner, K.; Burlacov, I.; Spies, H.-J.; Strämke, M.; Strämke, S.

2015-01-01

A laboratory scale plasma nitriding monitoring reactor (PLANIMOR) has been designed to study the basics of active screen plasma nitriding (ASPN) processes. PLANIMOR consists of a tube reactor vessel, made of borosilicate glass, enabling optical emission spectroscopy (OES) and infrared absorption spectroscopy. The linear setup of the electrode system of the reactor has the advantages to apply the diagnostic approaches on each part of the plasma process, separately. Furthermore, possible changes of the electrical field and of the heat generation, as they could appear in down-scaled cylindrical ASPN reactors, are avoided. PLANIMOR has been used for the nitriding of steel samples, achieving similar results as in an industrial scale ASPN reactor. A compact spectrometer using an external cavity quantum cascade laser combined with an optical multi-pass cell has been applied for the detection of molecular reaction products. This allowed the determination of the concentrations of four stable molecular species (CH 4 , C 2 H 2 , HCN, and NH 3 ). With the help of OES, the rotational temperature of the screen plasma could be determined

Plasma nitriding monitoring reactor: A model reactor for studying plasma nitriding processes using an active screen

Energy Technology Data Exchange (ETDEWEB)

Hamann, S., E-mail: hamann@inp-greifswald.de; Röpcke, J. [INP-Greifswald, Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Börner, K.; Burlacov, I.; Spies, H.-J. [TU Bergakademie Freiberg, Institute of Materials Engineering, Gustav-Zeuner-Str. 5, 09599 Freiberg (Germany); Strämke, M.; Strämke, S. [ELTRO GmbH, Arnold-Sommerfeld-Ring 3, 52499 Baesweiler (Germany)

2015-12-15

A laboratory scale plasma nitriding monitoring reactor (PLANIMOR) has been designed to study the basics of active screen plasma nitriding (ASPN) processes. PLANIMOR consists of a tube reactor vessel, made of borosilicate glass, enabling optical emission spectroscopy (OES) and infrared absorption spectroscopy. The linear setup of the electrode system of the reactor has the advantages to apply the diagnostic approaches on each part of the plasma process, separately. Furthermore, possible changes of the electrical field and of the heat generation, as they could appear in down-scaled cylindrical ASPN reactors, are avoided. PLANIMOR has been used for the nitriding of steel samples, achieving similar results as in an industrial scale ASPN reactor. A compact spectrometer using an external cavity quantum cascade laser combined with an optical multi-pass cell has been applied for the detection of molecular reaction products. This allowed the determination of the concentrations of four stable molecular species (CH{sub 4}, C{sub 2}H{sub 2}, HCN, and NH{sub 3}). With the help of OES, the rotational temperature of the screen plasma could be determined.

Reactors set for mini market

International Nuclear Information System (INIS)

Knox, Richard.

1988-01-01

Commercial nuclear power generation on a large-scale has an uncertain future. However, it is hoped that a small nuclear reactor could form the basis for providing heating, cooling or electricity in large buildings. Based on the Slowpoke research reactor, the Slowpoke energy system concept is simple. The concept and the way in which the small-scale reactor would work are discussed. The system consists of a stainless steel tank surrounded by reinforced concrete and let into the ground. The tank is full of light water which is heated to about 90 deg C by a central core of 2.4 percent enriched uranium fuel. The resulting natural circulation causes the water to pass through a heat exchanger. The water from the heat exchanger can be used for building or district heating, to operate air-conditioners or to generate small quantities of electricity. It is hoped to automate the operation of the reactor so that continuous supervision by a team of engineers would be unnecessary. A single operator on call in the building would be able to take control actions if the reactor's safety system failed. (UK)

Reactor core for LMFBR type reactors

International Nuclear Information System (INIS)

Masumi, Ryoji; Azekura, Kazuo; Kurihara, Kunitoshi; Bando, Masaru; Watari, Yoshio.

1987-01-01

Purpose: To reduce the power distribution fluctuations and obtain flat and stable power distribution throughout the operation period in an LMFBR type reactor. Constitution: In the inner reactor core region and the outer reactor core region surrounding the same, the thickness of the inner region is made smaller than the axial height of the reactor core region and the radial width thereof is made smaller than that of the reactor core region and the volume thereof is made to 30 - 50 % for the reactor core region. Further, the amount of the fuel material per unit volume in the inner region is made to 70 - 90 % of that in the outer region. The difference in the neutron infinite multiplication factor between the inner region and the outer region is substantially constant irrespective of the burnup degree and the power distribution fluctuation can be reduced to about 2/3, by which the effect of thermal striping to the reactor core upper mechanisms can be moderated. Further, the maximum linear power during operation can be reduced by 3 %, by which the thermal margin in the reactor core is increased and the reactor core fuels can be saved by 3 %. (Kamimura, M.)

Structural integrity of water reactor pressure boundary components

International Nuclear Information System (INIS)

Loss, F.J.

1977-01-01

The dynamic fracture toughness was determined as a function of temperature for three-point bend specimens of A533-B, A508-2, and A302-B steels. Crack propagation rates at 288 0 C in a water reactor environment were determined for A533-B and A508-2. Radiation-induced degradation of notch toughness of reactor steels and welds was explored. The ''warm prestress'' occurring in a flawed reactor vessel following a LOCA and operation of ECCS was studied. 25 figures

An Idea of 20% test of the Initial Core Reactor Physics

International Nuclear Information System (INIS)

Roh, Kyung Ho; Yang, Sung Tae; Jung, Ji Eun

2012-01-01

Many tests have been performed on the OPR1000 and APR1400 before commercial operation. Some of these tests were performed at reactor power levels of 20% and 50%. The CPC (Core Protection Calculator) power distribution test is one of these tests. It is performed to assure the reliability of the Core Protection Calculator System (CPCS). Through this test, SAM1 is calculated using the snapshots2. The test takes about nine hours at a reactor power level of 20% and about thirty hours at a reactor power level of 50%. SAM used at each reactor power level is as follows: 1. Reactor power of 0% ∼ 20%: Designed SAM (DSAM) 2. Reactor power of 20% ∼ 50%: SAM calculated (C-SAM) at a reactor power of 20% 3. Reactor power 50% ∼ End of Cycle : SAM calculated at a reactor power of 50% As mentioned earlier, SAM is calculated and punched into CPC to assure the reliability of CPCS. Therefore, CPC is operated having penalties with D-SAM until3 reaching a reactor power of 20%. That is, the penalty of CPC will be removed when SAM is calculated and punched into the CPC at a reactor power of 20%. But these penalties are considered to be removed after a reactor power of 50% test in order to maintain the conservatism of the CPC. This is done because the final values calculated using C-SAM, in contrast to those calculated using SAM, a reactor power of 50%, are not correct. This paper began from an idea, 'If so, what would happen if we removed the CPC power distribution test at a reactor power of 20%?'

Oxidative coupling of methane using inorganic membrane reactor

Energy Technology Data Exchange (ETDEWEB)

Ma, Y.H.; Moser, W.R.; Dixon, A.G. [Worcester Polytechnic Institute, MA (United States)] [and others

1995-12-31

The goal of this research is to improve the oxidative coupling of methane in a catalytic inorganic membrane reactor. A specific target is to achieve conversion of methane to C{sub 2} hydrocarbons at very high selectivity and relatively higher yields than in fixed bed reactors by controlling the oxygen supply through the membrane. A membrane reactor has the advantage of precisely controlling the rate of delivery of oxygen to the catalyst. This facility permits balancing the rate of oxidation and reduction of the catalyst. In addition, membrane reactors minimize the concentration of gas phase oxygen thus reducing non selective gas phase reactions, which are believed to be a main route for formation of CO{sub x} products. Such gas phase reactions are a cause for decreased selectivity in oxidative coupling of methane in conventional flow reactors. Membrane reactors could also produce higher product yields by providing better distribution of the reactant gases over the catalyst than the conventional plug flow reactors. Modeling work which aimed at predicting the observed experimental trends in porous membrane reactors was also undertaken in this research program.

Residual stress in the first wall coating materials of TiC and TiN for fusion reactor

International Nuclear Information System (INIS)

Qiu Shaoyu

1997-01-01

Residual stresses measurement in the first wall coating of a fusion reactor of TiC and TiN films by X-ray diffraction 'sin 2 ψ methods' were described. The authors have studied on the effect of conditions of specimen preparation (such as coating method, substrate materials, film thickness and deposition temperature) on the residual stress of TiC and TiN films coated onto Mo, 316LSS and Pocographite by chemical vapor deposition (CVD) and physical vapor deposition (PVD) method. All films prepared in this study were found to have a compressive stresses and the CVD method gave lower residual stress than PVD method. TiC film coated on Mo substrate at 1100 degree C by CVD method showed that residual stress as the film thickness was raised from 14 μm to 60 μm, on the other hand, residual stress by PVD method exhibited a high compressive stresses, this kind of stress was principally the intrinsic stress, and a marked decrease in the residual with raising the deposition temperature (200 degree C∼650 degree C) was demonstrated. Origins of the residual stress were discussed by correlation with differences between thermal expansion coefficients, and also with fabrication methods

A comparative study of the mechanical and thermal properties of defective ZrC, TiC and SiC.

Science.gov (United States)

Jiang, M; Zheng, J W; Xiao, H Y; Liu, Z J; Zu, X T

2017-08-24

ZrC and TiC have been proposed to be alternatives to SiC as fuel-cladding and structural materials in nuclear reactors due to their strong radiation tolerance and high thermal conductivity at high temperatures. To unravel how the presence of defects affects the thermo-physical properties under irradiation, first-principles calculations based on density function theory were carried out to investigate the mechanical and thermal properties of defective ZrC, TiC and SiC. As compared with the defective SiC, the ZrC and TiC always exhibit larger bulk modulus, smaller changes in the Young's and shear moduli, as well as better ductility. The total thermal conductivity of ZrC and TiC are much larger than that of SiC, implying that under radiation environment the ZrC and TiC will exhibit superior heat conduction ability than the SiC. One disadvantage for ZrC and TiC is that their Debye temperatures are generally lower than that of SiC. These results suggest that further improving the Debye temperature of ZrC and TiC will be more beneficial for their applications as fuel-cladding and structural materials in nuclear reactors.

Development of the IAEA’s Knowledge Preservation Portals for Fast Reactors and Gas-Cooled Reactors Knowledge Preservation

International Nuclear Information System (INIS)

Batra, C.; Menahem, D. Beraha; Kriventsev, V.; Monti, S.; Reitsma, F.; Grosbois, J. de; Khoroshev, M.; Gladyshev, M.

2016-01-01

Full text: The IAEA has been carrying out a dedicated initiative on fast reactor knowledge preservation since 2003. The main objectives of the Fast Reactor Knowledge Portal (FRKP) initiative are to, a) halt the on-going loss of information related to fast reactors (FR), and b) collect, retrieve, preserve and make accessible existing data and information on FR. This portal will help in knowledge sharing, development, search and discovery, collaboration and communication of fast reactor related information. On similar lines a Gas Cooled Fast Reactor Knowledge Preservation portal project also started in 2013. Knowledge portals are capable to control and manage both publicly available as well as controlled information. The portals will not only incorporate existing set of knowledge and information, but will also provide a systemic platform for further preservation of new developments. It will include fast reactor and gas cooled reactor document repositories, project workspaces for the IAEA’s Coordinated Research Projects (CRPs), Technical Meetings (TMs), forums for discussion, etc. The portal will also integrate a taxonomy based search tool, which will help using new semantic search capabilities for improved conceptual retrieve of documents. The taxonomy complies with international web standards as defined by the W3C (World Wide Web Consortium). (author

Cascade reactor: introduction

International Nuclear Information System (INIS)

Pitts, J.H.

1985-01-01

Cascade is a concept for an ultrasafe, highly efficient, easily built reactor to convert inertial-confinement fusion energy into electrical power. The Cascade design includes a rotating double-cone-shaped chamber in which a moving, 1-m-thick ceramic granular blanket is held against the reactor wall by centrifugal action. The granular material absorbs energy from the fusion reactions. Accomplishments this year associated with Cascade included improvements to simplify chamber design and lower activation. The authors switched from a steel chamber wall to one made from silicon-carbide (SiC) panels held in compression by SiC-fiber/Al-composite tendons that gird the chamber both circumferentially and axially. The authors studies a number of heat-exchanger designs and selected a gravity-flow cascade design with a vacuum on the primary side. This design allows granules leaving the chamber to be transported to the heat exchangers using their own peripheral speed. The granules transfer their thermal energy and return to the chamber gravitationally: no vacuum locks or conveyors are needed

Reactors. Nuclear propulsion ships

International Nuclear Information System (INIS)

Fribourg, Ch.

2001-01-01

This article has for object the development of nuclear-powered ships and the conception of the nuclear-powered ship. The technology of the naval propulsion P.W.R. type reactor is described in the article B.N.3 141 'Nuclear Boilers ships'. (N.C.)

Qualification issues for advanced light-water reactor protection systems

International Nuclear Information System (INIS)

Korsah, K.; Clark, R.L.; Antonescu, C.

1993-01-01

The instrumentation and control (I ampersand C) systems in advanced reactors will make extensive use of digital controls, microprocessors, multiplexing, and fiber optic transmission. Elements of these advances in I ampersand C have been implemented on some current operating plants. However, the widespread use of the above technologies, as well as the use of artificial intelligence with minimum reliance on human operator control of reactors, highlights the need to develop standards for qualifying the I ampersand C used in the next generation of nuclear power plants. As a first step in this direction, the protection system I ampersand C for present-day plants was compared to that proposed for advanced light-water reactors (ALWRs). An evaluation template was developed by assembling a configuration of a safety channel instrument string for a generic ALWR, then comparing the impact of environmental stressors on that string to their effect on an equivalent instrument string from an existing light-water reactor. The template was then used to suggest a methodology for the qualification of microprocessor-based protection systems. The methodology identifies standards/regulatory guides (or lack thereof) for the qualification of microprocessor-based safety I ampersand C systems. This approach addresses in part issues raised in NRC policy document SECY-91-292, which recognizes that advanced I ampersand C systems for the nuclear industry are ''being developed without consensus standards. as the technology available for design is ahead of the technology that is well understood through experience and supported by application standards.''

Temperature measurement of the reactor materials samples irradiated in the fuel channels of the RA reactor - Annex 16

International Nuclear Information System (INIS)

Nikolic, M.; Djalovic, M.

1964-01-01

Reactor materials as graphite, stainless steel, magnox, zirconium alloys, etc. were exposed to fast neutron flux inside the fuel elements specially adapted for this purpose. Samples in the form ampoules were placed in capsules inside the fuel channels and cooled by heavy water which cools the fuel elements. In order to monitor the samples temperature 42 thermocouples were placed in the samples. That was necessary for reactor safety reasons and for further interpretation of measured results. Temperature monitoring was done continuously by multichannel milivoltmeters. This paper describes the technique of introducing the thermocouples, compensation instruments, control of the cold ends and adaptation of the instruments for precision (0.5%) temperature measurement in the range 30 deg - 130 deg C; 30 deg - 280 deg C and 30 deg - 80 deg C [sr

Synthesis of superior fast charging-discharging nano-LiFePO4/C from nano-FePO4 generated using a confined area impinging jet reactor approach.

Science.gov (United States)

Liu, Xiao-min; Yan, Pen; Xie, Yin-Yin; Yang, Hui; Shen, Xiao-dong; Ma, Zi-Feng

2013-06-14

LiFePO4/C nanocomposites with excellent electrochemical performance is synthesized from nano-FePO4, generated by a novel method using a confined area impinging jet reactor (CIJR). When discharged at 80 C (13.6 Ag(-1)), the LiFePO4/C delivers a discharge capacity of 95 mA h g(-1), an energy density of 227 W h kg(-1) and a power density of 34 kW kg(-1).

High-temperature reactor developments in the Netherlands

International Nuclear Information System (INIS)

Schram, R.P.C.; Cordfunke, E.H.P.; Heek, A.I. van.

1996-01-01

The high-temperature reactor development in the Netherland is embedded in the WHITE reactor program, in which several Dutch research institutes and engineering companies participate. The activities within the WHITE program are focused on the development of a small scale HTS for combined heat and power generation. In 1995, design choices for a pebble bed reactor were made at ECN. The first concept HTR will gave a closed cycle helium turbine and a power level of 40 MWth. It is intended to make the market introduction of a commercially competitive HTR feasible. The design will be an optimization of the Peu-a-Peu (PAP) concept of KFA Juelich. Computer codes necessary for the evaluation of reactor physics aspects of this reactor are developed in cooperation with international partners. An evaluation of a 20 MWth PAP concept showed that the maximum fuel termmperature after depressurization does not exceed 1300 C. (orig.)

[Present conceptions of the C.E.A. concerning] the development of fast neutron reactors in France

International Nuclear Information System (INIS)

Vendryes, G.; Gaussens, J.

1964-01-01

1 - The position of fast neutron reactors in the French nuclear energy program. In developing a program based on natural uranium, France will have an important stock of plutonium rich in higher isotopes. The existence of this plutonium and of the depleted uranium arising from the same reactors, has, as a logical consequence, the use of both in fast neutron reactors. Justified by this short term interest, the achievement of fast neutron reactors does, moreover, provide for a future necessity. 2 - Description of a fast neutron central power station of 1000 MWe. We indicate the characteristics of a future fast neutron central power station, plutonium fuelled, and sodium cooled. However uncertain these characteristics may be, they constitute a necessary guide in the orientation of our work. 3 - Studies carried out up to the present time. We give an outline of those studies, often very preliminary, which have given the characteristics cited above. The principal technical areas taken up are the following: - Neutronics (critical masses, breeding ratios, enrichments, flattening of the neutron flux, coefficients of reactivity, reactivity changes as a function of irradiation). - Dynamics, control, and safety. - Technology (design of the core and vessel, of the sodium system, and of the fuel handling mechanisms). These technical studies are complemented by economic considerations. The choice of the optimum characteristics is related to the existence of power production programs, and, in these programs, to the existence of plutonium producing thermal reactors. It is shown how, in this context, the existence of plutonium should be taken into account, and, in addition which mechanisms relate the economics of this plutonium to the choice of the most important parameters of the breeder reactors. 4 - Prototype reactor. The interest in an intermediate stage consisting of a reactor of a power level of about 80 MWe is justified. Its essential characteristics are briefly presented

Design and evaluation of materials for space reactors

International Nuclear Information System (INIS)

Tavassoli, A.A.; Vrillon, B.; Robert, G.

1990-01-01

The French programme envisages a 20 kWe reactor, project ERATO, with three technological options. The first option is a sodium cooled reactor, derived from the fast breeder reactor technology, (upper core outlet temperature of 700 0 C). The second option is based on the High Temperature Gas-cooled Reactor technology (outlet temperature range 700 0 C-900 0 C). The third option is the reference solution, lithium cooled and UN fuelled fast spectrum reactor, (outlet temperature as high as 1200 0 C). The choice is essentially dominated by material considerations, and more specifically by the problems related to the compatibility with the cooling medium and to the high temperature creep resistance. For the first system limited work will be needed as the technology used is well experimented and there is a wealth of information on the austenitic stainless steel Type 316L-SPH. For the second system, most of the work has been concentrated on characterization of existing commercial alloys. This has included the preselection and the testing of a number of superalloys irradiated or not. The results obtained from high temperature tensile and creep tests have allowed selection of Haynes 230 as the primary candidate material and have also permitted calculation of allowable design stresses for this alloy. For the very high temperature system the French R and D programme has focused on Mo-Re alloys. The results obtained to this date from microstructural examinations and mechanical tests performed on different alloy compositions have allowed selection of Mo-25%Re for future optimization work. They have also shown the need for evaluation of creep properties at low stresses where microstructural instabilities are likely to occur as a result of long exposure to high temperature

A PC-based high temperature gas reactor simulator for Indonesian conceptual HTR reactor basic training

Science.gov (United States)

Syarip; Po, L. C. C.

2018-05-01

In planning for nuclear power plant construction in Indonesia, helium cooled high temperature reactor (HTR) is favorable for not relying upon water supply that might be interrupted by earthquake. In order to train its personnel, BATAN has cooperated with Micro-Simulation Technology of USA to develop a 200 MWt PC-based simulation model PCTRAN/HTR. It operates in Win10 environment with graphic user interface (GUI). Normal operation of startup, power maneuvering, shutdown and accidents including pipe breaks and complete loss of AC power have been conducted. A sample case of safety analysis simulation to demonstrate the inherent safety features of HTR was done for helium pipe break malfunction scenario. The analysis was done for the variation of primary coolant pipe break i.e. from 0,1% - 0,5 % and 1% - 10 % helium gas leakages, while the reactor was operated at the maximum constant power of 10 MWt. The result shows that the highest temperature of HTR fuel centerline and coolant were 1150 °C and 1296 °C respectively. With 10 kg/s of helium flow in the reactor core, the thermal power will back to the startup position after 1287 s of helium pipe break malfunction.

Enrichment of acetogenic bacteria in high rate anaerobic reactors under mesophilic and thermophilic conditions.

Science.gov (United States)

Ryan, P; Forbes, C; McHugh, S; O'Reilly, C; Fleming, G T A; Colleran, E

2010-07-01

The objective of the current study was to expand the knowledge of the role of acetogenic Bacteria in high rate anaerobic digesters. To this end, acetogens were enriched by supplying a variety of acetogenic growth supportive substrates to two laboratory scale high rate upflow anaerobic sludge bed (UASB) reactors operated at 37 degrees C (R1) and 55 degrees C (R2). The reactors were initially fed a glucose/acetate influent. Having achieved high operational performance and granular sludge development and activity, both reactors were changed to homoacetogenic bacterial substrates on day 373 of the trial. The reactors were initially fed with sodium vanillate as a sole substrate. Although % COD removal indicated that the 55 degrees C reactor out performed the 37 degrees C reactor, effluent acetate levels from R2 were generally higher than from R1, reaching values as high as 5023 mg l(-1). Homoacetogenic activity in both reactors was confirmed on day 419 by specific acetogenic activity (SAA) measurement, with higher values obtained for R2 than R1. Sodium formate was introduced as sole substrate to both reactors on day 464. It was found that formate supported acetogenic activity at both temperatures. By the end of the trial, no specific methanogenic activity (SMA) was observed against acetate and propionate indicating that the methane produced was solely by hydrogenotrophic Archaea. Higher SMA and SAA values against H(2)/CO(2) suggested development of a formate utilising acetogenic population growing in syntrophy with hydrogenotrophic methanogens. Throughout the formate trial, the mesophilic reactor performed better overall than the thermophilic reactor. Copyright 2010 Elsevier Ltd. All rights reserved.

Advanced I&C for Fault-Tolerant Supervisory Control of Small Modular Reactors

Energy Technology Data Exchange (ETDEWEB)

Cole, Daniel G. [Univ. of Pittsburgh, PA (United States)

2018-01-30

In this research, we have developed a supervisory control approach to enable automated control of SMRs. By design the supervisory control system has an hierarchical, interconnected, adaptive control architecture. A considerable advantage to this architecture is that it allows subsystems to communicate at different/finer granularity, facilitates monitoring of process at the modular and plant levels, and enables supervisory control. We have investigated the deployment of automation, monitoring, and data collection technologies to enable operation of multiple SMRs. Each unit's controller collects and transfers information from local loops and optimize that unit’s parameters. Information is passed from the each SMR unit controller to the supervisory controller, which supervises the actions of SMR units and manage plant processes. The information processed at the supervisory level will provide operators the necessary information needed for reactor, unit, and plant operation. In conjunction with the supervisory effort, we have investigated techniques for fault-tolerant networks, over which information is transmitted between local loops and the supervisory controller to maintain a safe level of operational normalcy in the presence of anomalies. The fault-tolerance of the supervisory control architecture, the network that supports it, and the impact of fault-tolerance on multi-unit SMR plant control has been a second focus of this research. To this end, we have investigated the deployment of advanced automation, monitoring, and data collection and communications technologies to enable operation of multiple SMRs. We have created a fault-tolerant multi-unit SMR supervisory controller that collects and transfers information from local loops, supervise their actions, and adaptively optimize the controller parameters. The goal of this research has been to develop the methodologies and procedures for fault-tolerant supervisory control of small modular reactors. To achieve

The analysis of thermal-hydraulic performances of nuclear ship reactor

International Nuclear Information System (INIS)

Wakabayashi, Shinshichi; Hamada, Masao

1975-01-01

Thermal-hydraulic performances in the core of nuclear ship reactor was analysed by thermal-hydraulic analyser codes, AMRTC and COBRA-11+DNBCAL. This reactor is of a pressurized water type and incorporates the steam generator within the reactor vessel with the rated power of 330 MWt, which is developed by Nuclear Ship Research Panel Seven (NSR-7) in The Shipbuilding Research Association of Japan. Fuel temperature distributions, coolant temperature distributions, void fractions in coolant and minimum burn out ratio etc. were calculated. Results are as follows; a) The maximum temperature of fuel center is 1,472 0 C that corresponds to 53% as small as the melting point (2,800 0 C). b) Subcooled boiling exists in the core and the maximum void fraction is less than 4%. c) The minimum burn out ratio is not less than the minimum allowable limit of 1.25. It was found from the results of analysis that this reactor was able to be operated wide margin with respect to thermal-hydraulic design limits at the rated power. (auth.)

The dismantling of fast reactors: sodium processing

International Nuclear Information System (INIS)

Rodriguez, G.; Berte, M.; Serpante, J.P.

1999-01-01

Fast reactors require a coolant that does not slow down neutrons so water can not be used. Metallic sodium has been chosen because of its outstanding neutronic and thermal properties but sodium reacts easily with air and water and this implies that sodium-smeary components can not be considered as usual nuclear wastes. A stage of sodium neutralizing is necessary in the processing of wastes from fast reactors. Metallic sodium is turned into a chemically stable compound: soda, carbonates or sodium salts. This article presents several methods used by Framatome in an industrial way when dismantling sodium-cooled reactors. (A.C.)

ULTRA SCWR+: Practical advanced water reactor concepts

International Nuclear Information System (INIS)

Duffey, Romney; Khartabil, Hussam; Kuran, Sermet; Zhou, Tracy; Pioro, Igor

2008-01-01

Modern thermal power plants now utilize supercritical steam cycles with thermal efficiencies of over 45%. Recent developments have lead to Ultra-SuperCritical (USC) systems, which adopt reheat turbines that can attain efficiencies of over 50%. Because these turbines are already developed, demonstrated and deployed worldwide, and use existing and traditional steam cycle technology, the simplest nuclear advance is to utilize these proven thermal cycle conditions by coupling this turbine type to a reactor. This development direction is fundamentally counter to the usual approach of adopting high-temperature gas-cooled (helium-cooled) reactor cycles, for which turbines have yet to be demonstrated on commercial scale unlike the supercritical steam turbines. The ULTRA (Ultra-supercritical Light water Thermal ReActor) SCWR+ concept adopts the fundamental design approach of matching a water and steam-cooled reactor to the ultra-supercritical steam cycle, adopting the existing and planned thermal power plant turbines. The HP and IP sections are fed with conditions of 25 MPa/625degC and 7 MPa/700degC, respectively, to achieve operating plant thermal efficiencies in excess of 50%, with a direct turbine cycle. By using such low-pressure reheated steam, this concept also adopts technology that was explored and used many years ago in existing water reactors, with the potential to produce large quantities of low cost heat, which can be used for other industrial and district processes. Pressure-Tube (PT) reactors are suitable for adoption of this design approach and, in addition, have other advantages that will significantly improve water-cooled reactor technology. These additional advantages include enhanced safety and improved resource utilization and proliferation resistance. This paper describes the PT-SCWR+ concept and its potential enhancements. (author)

Development of the cascade inertial-confinement-fusion reactor

International Nuclear Information System (INIS)

Pitts, J.H.

1985-01-01

Caqscade, originally conceived as a football-shaped, steel-walled reactor containing a Li 2 O granule blanket, is now envisaged as a double-cone-shaped reactor containing a two-layered (three-zone) flowing blanket of BeO and LiAlO 2 granules. Average blanket exit temperature is 1670 K and gross plant efficiency (net thermal conversion efficiency) using a Brayton cycle is 55%. The reactor has a low-activation SiC-tiled wall. It rotates at 50 rpm, and the granules are transported to the top of the heat exchanger using their peripheral speed; no conveyors or lifts are required. The granules return to the reactor by gravity. After considerable analysis and experimentation, we continue to regard Cascade as a promising reactor concept with the advantages of safety, efficiency, and low activation

Development of the cascade inertial-confinement-fusion reactor

International Nuclear Information System (INIS)

Pitts, J.H.

1985-01-01

Cascade, originally conceived as a football-shaped, steel-walled reactor containing a Li 2 O granule blanket, is now envisaged as a double-cone-shaped reactor containing a two-layered (three-zone) flowing blanket of BeO and LiAlO 2 granules. Average blanket exit temperature is 1670 0 K and gross plant efficiency (net thermal conversion efficiency) using a Brayton cycle is 55%. The reactor has a low-activation SiC-tiled wall. It rotates at 50 rpm, and the granules are transported to the top of the heat exchanger using their peripheral speed; no conveyors or lifts are required. The granules return to the reactor by gravity. After considerable analysis and experimentation, we continue to regard Cascade as a promising reactor concept with the advantages of safety, efficiency, and low activation

Innovative energy production in fusion reactors

International Nuclear Information System (INIS)

Iiyoshi, A.; Momota, H.; Motojima, O.

1994-01-01

Concepts of innovative energy production in neutron-lean fusion reactors without having the conventional turbine-type generator are proposed for improving the plant efficiency. These concepts are (a) traveling wave direct energy conversion of 14.7 MeV protons, (b) cusp type direct energy conversion of charged particles, (c) efficient use of radiation with semiconductor and supplying clean fuel in a form of hydrogen gas, and (d) direct energy conversion from deposited heat to electric power with semiconductor utilizing Nernst effect. The candidates of reactors such as a toroidal system and an open system are also studied for application of the new concepts. The study shows the above concepts for a commercial reactor are promising. (author)

Innovative energy production in fusion reactors

International Nuclear Information System (INIS)

Iiyoshi, A.; Momota, H.; Motojima, O.; Okamoto, M.; Sudo, S.; Tomita, Y.; Yamaguchi, S.; Ohnishi, M.; Onozuka, M.; Uenosono, C.

1993-10-01

Concepts of innovative energy production in neutron-lean fusion reactors without having the conventional turbine-type generator are proposed for improving the plant efficiency. These concepts are (a) traveling wave direct energy conversion of 14.7 MeV protons, (b) cusp type direct energy conversion of charged particles, (c) efficient use of radiation with semiconductor and supplying clean fuel in a form of hydrogen gas, and (d) direct energy conversion from deposited heat to electric power with semiconductor utilizing Nernst effect. The candidates of reactors such as a toroidal system and an open system are also studied for application of the new concepts. The study shows the above concepts for a commercial reactor are promising. (author)

Innovative energy production in fusion reactors

Energy Technology Data Exchange (ETDEWEB)

Iiyoshi, A.; Momota, H.; Motojima, O.; Okamoto, M.; Sudo, S.; Tomita, Y.; Yamaguchi, S.; Ohnishi, M.; Onozuka, M.; Uenosono, C.

1993-10-01

Concepts of innovative energy production in neutron-lean fusion reactors without having the conventional turbine-type generator are proposed for improving the plant efficiency. These concepts are (a) traveling wave direct energy conversion of 14.7 MeV protons, (b) cusp type direct energy conversion of charged particles, (c) efficient use of radiation with semiconductor and supplying clean fuel in a form of hydrogen gas, and (d) direct energy conversion from deposited heat to electric power with semiconductor utilizing Nernst effect. The candidates of reactors such as a toroidal system and an open system are also studied for application of the new concepts. The study shows the above concepts for a commercial reactor are promising. (author).

Molten salt reactors. The AMSTER concept

International Nuclear Information System (INIS)

Vergnes, J.; Garzenne, C.; Lecarpentier, D.; Mouney, H.

2001-01-01

This article presents the concept of actinide molten salt transmuter (AMSTER). This reactor is graphite-moderated and is dedicated to the burning of actinides. The main difference with a molten salt reactor is that its liquid fuel undergoes an on-line partial reprocessing in which fission products are extracted and heavy nuclei are reintroduced into the fuel. In order to maintain the reactivity regular injections of 235 U-salt are made. In classical reactors, fuel burn-up is limited by the swelling of the cladding and the radiation fuel pellets resistance, in AMSTER there is no limitation to the irradiation time of the fuel, so all the actinides can be burnt or transmuted. (A.C.)

Alcohol synthesis in a high-temperature slurry reactor

Energy Technology Data Exchange (ETDEWEB)

Roberts, G.W.; Marquez, M.A.; McCutchen, M.S. [North Carolina State Univ., Raleigh, NC (United States)

1995-12-31

The overall objective of this contract is to develop improved process and catalyst technology for producing higher alcohols from synthesis gas or its derivatives. Recent research has been focused on developing a slurry reactor that can operate at temperatures up to about 400{degrees}C and on evaluating the so-called {open_quotes}high pressure{close_quotes} methanol synthesis catalyst using this reactor. A laboratory stirred autoclave reactor has been developed that is capable of operating at temperatures up to 400{degrees}C and pressures of at least 170 atm. The overhead system on the reactor is designed so that the temperature of the gas leaving the system can be closely controlled. An external liquid-level detector is installed on the gas/liquid separator and a pump is used to return condensed slurry liquid from the separator to the reactor. In order to ensure that gas/liquid mass transfer does not influence the observed reaction rate, it was necessary to feed the synthesis gas below the level of the agitator. The performance of a commercial {open_quotes}high pressure {close_quotes} methanol synthesis catalyst, the so-called {open_quotes}zinc chromite{close_quotes} catalyst, has been characterized over a range of temperature from 275 to 400{degrees}C, a range of pressure from 70 to 170 atm., a range of H{sub 2}/CO ratios from 0.5 to 2.0 and a range of space velocities from 2500 to 10,000 sL/kg.(catalyst),hr. Towards the lower end of the temperature range, methanol was the only significant product.

REACTOR GROUT THERMAL PROPERTIES

Energy Technology Data Exchange (ETDEWEB)

Steimke, J.; Qureshi, Z.; Restivo, M.; Guerrero, H.

2011-01-28

Savannah River Site has five dormant nuclear production reactors. Long term disposition will require filling some reactor buildings with grout up to ground level. Portland cement based grout will be used to fill the buildings with the exception of some reactor tanks. Some reactor tanks contain significant quantities of aluminum which could react with Portland cement based grout to form hydrogen. Hydrogen production is a safety concern and gas generation could also compromise the structural integrity of the grout pour. Therefore, it was necessary to develop a non-Portland cement grout to fill reactors that contain significant quantities of aluminum. Grouts generate heat when they set, so the potential exists for large temperature increases in a large pour, which could compromise the integrity of the pour. The primary purpose of the testing reported here was to measure heat of hydration, specific heat, thermal conductivity and density of various reactor grouts under consideration so that these properties could be used to model transient heat transfer for different pouring strategies. A secondary purpose was to make qualitative judgments of grout pourability and hardened strength. Some reactor grout formulations were unacceptable because they generated too much heat, or started setting too fast, or required too long to harden or were too weak. The formulation called 102H had the best combination of characteristics. It is a Calcium Alumino-Sulfate grout that contains Ciment Fondu (calcium aluminate cement), Plaster of Paris (calcium sulfate hemihydrate), sand, Class F fly ash, boric acid and small quantities of additives. This composition afforded about ten hours of working time. Heat release began at 12 hours and was complete by 24 hours. The adiabatic temperature rise was 54 C which was within specification. The final product was hard and displayed no visible segregation. The density and maximum particle size were within specification.

Analysis of gamma ray intensity on the S/C vent pipes area in the unit 2 reactor building of the Fukushima Daiichi Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Cho, Jai Wan; Choi, Young Soo; Jeong, Kyung Min [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The robot is equipped with cameras, a dosimeter, and 2 DOF (degree of freedom) manipulation arms. It loads a small vehicle equipped with a camera that can access and inspect narrow areas. TEPCO is using the four-legged walking robot to inspect the suppression chamber (S/C) area of the unit 2 reactor building basement in the Fukushima Daiichi Nuclear Power Plant. The robot carried out 6 missions for about four months, from 11 December, 2012 to 15 March, 2013, where it examined an evidence of a leakage of radioactivity contaminated water in the S/C area of unit 2 reactor building. When a camera's signal processing unit, which is consist of ASIC and FPGA devices manufactured by a CMOS fabrication process, is exposed to a higher dose rate gamma ray, the speckle distribution in the camera image increase more. From the inspection videos, released by TEPCO, of the underground 8 vent pipes in the unit 2 reactor building, we analyzed the speckle distribution from the high dose-rate gamma rays. Based on the distribution of the speckle, we attempted to characterize the vent pipe with much radioactivity contaminated materials among the eight vent pipes connected to the PCV. The numbers of speckles viewed in the image of a CCD (or CMOS) camera are related to an intensity of the gamma ray energy emitted by a nuclear fission reaction from radioactivity materials. The numbers of speckles generated by gamma ray irradiation in the camera image are calculated by an image processing technique. Therefore, calculating the speckles counts, we can determine the vent pipe with relatively most radioactivity-contaminated materials among the other vent pipes. From the comparison of speckles counts calculated in the inspection image of the vent pipe with the speckles counts extracted by gamma ray irradiation experiment of the same small vehicle camera model loaded with the four-legged walking robot, we can qualitatively estimate the gamma ray dose-rate in the S/C vent pipe area of the

Irradiation effects on C/C composite materials for high temperature nuclear applications

International Nuclear Information System (INIS)

Eto, M.; Ugachi, H.; Baba, S.I.; Ishiyama, S.; Ishihara, M.; Hayashi, K.

2000-01-01

Excellent characteristics such as high strength and high thermal shock resistance of C/C composite materials have led us to try to apply them to the high temperature components in nuclear facilities. Such components include the armour tile of the first wall and divertor of fusion reactor and the elements of control rod for the use in HTGR. One of the most important aspects to be clarified about C/C composites for nuclear applications is the effect of neutron irradiation on their properties. At the Japan Atomic Energy Research Institute (JAERI), research on the irradiation effects on various properties of C/C composite materials has been carried out using fission reactors (JRR-3, JMTR), accelerators (TANDEM, TIARA) and the Fusion Neutronics Source (FNS). Additionally, strength tests of some neutron-irradiated elements for the control rod were carried out to investigate the feasibility of C/C composites. The paper summarises the R and D activities on the irradiation effects on C/C composites. (authors)

Conceptual design study of small lead-bismuth cooled reactor

International Nuclear Information System (INIS)

Chikazawa, Yoshitaka; Hori, Toru; Kida, Masanori; Konomura, Mamoru

2004-11-01

In phase 2 of the feasibility study of commercialized fast reactor cycle systems of JNC, we make a concept of a small sodium cooled reactor for a power source of a city with various requirements, such as, safety and economical competitiveness. various reactor concepts are surveyed and a tank type reactor whose intermediate heat exchanger and primary main pumps are arranged in series is selected. In this study, a compact long life core and a simple reactor structure designs are pursued. The core type is three regional Zr concentration with one Pu enrichment core, the reactor outlet temperature achieves 550degC and the reactor electric output increases from 150 MWe to 165 MWe. The construction cost is much higher than the economical goal in the case of FOAK. But the construction cost in the case of NOAK is estimated to be 85.6% achieving the economical goal. (author)

K-capture by Al-Si based Additives in an Entrained Flow Reactor

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2016-01-01

A water slurry, consisting of KCl and Al-Si based additives (kaolin and coal fly ash) was fed into an entrained flow reactor (EFR) to study the K-capturing reaction of the additives at suspension-fired conditions. Solid products collected from the reactor were analysed with respect to total...... of KCl to K-aluminosilicate decreased. When reaction temperature increased from 1100 °C to 1450 °C, the conversion of KCl does not change significantly, which differs from the trend observed in fixed-bed reactor....

Large-scale hydrogen production using nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Ryland, D.; Stolberg, L.; Kettner, A.; Gnanapragasam, N.; Suppiah, S. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

2014-07-01

For many years, Atomic Energy of Canada Limited (AECL) has been studying the feasibility of using nuclear reactors, such as the Supercritical Water-cooled Reactor, as an energy source for large scale hydrogen production processes such as High Temperature Steam Electrolysis and the Copper-Chlorine thermochemical cycle. Recent progress includes the augmentation of AECL's experimental capabilities by the construction of experimental systems to test high temperature steam electrolysis button cells at ambient pressure and temperatures up to 850{sup o}C and CuCl/HCl electrolysis cells at pressures up to 7 bar and temperatures up to 100{sup o}C. In parallel, detailed models of solid oxide electrolysis cells and the CuCl/HCl electrolysis cell are being refined and validated using experimental data. Process models are also under development to assess options for economic integration of these hydrogen production processes with nuclear reactors. Options for large-scale energy storage, including hydrogen storage, are also under study. (author)

Reactor surface contamination stabilization. Innovative technology summary report

International Nuclear Information System (INIS)

1998-11-01

Contaminated surfaces, such as the face of a nuclear reactor, need to be stabilized (fixed) to avoid airborne contamination during decontamination and decommissioning activities, and to prepare for interim safe storage. The traditional (baseline) method of fixing the contamination has been to spray a coating on the surfaces, but ensuring complete coverage over complex shapes, such as nozzles and hoses, is difficult. The Hanford Site C Reactor Technology Demonstration Group demonstrated innovative technologies to assess stabilization properties of various coatings and to achieve complete coverage of complex surfaces on the reactor face. This demonstration was conducted in two phases: the first phase consisted of a series of laboratory assessments of various stabilization coatings on metal coupons. For the second phase, coatings that passed the laboratory tests were applied to the front face of the C Reactor and evaluated. The baseline coating (Rust-Oleum No. 769) and one of the innovative technologies did not completely cover nozzle assemblies on the reactor face, the most critical of the second-phase evaluation criteria. However, one of the innovative coating systems, consisting of a base layer of foam covered by an outer layer of a polymeric film, was successful. The baseline technology would cost approximately 33% as much as the innovative technology cost of $64,000 to stabilize an entire reactor face (196 m 2 or 2116 ft 2 ) with 2,004 nozzle assemblies, but the baseline system failed to provide complete surface coverage

An evaluation of reactor cooling and coupled hydrogen production processes using the modular helium reactor

International Nuclear Information System (INIS)

Harvego, E.A.; Reza, S.M.M.; Richards, M.; Shenoy, A.

2006-01-01

The high-temperature characteristics of the modular helium reactor (MHR) make it a strong candidate for producing hydrogen using either thermochemical or high-temperature electrolysis (HTE) processes. Using heat from the MHR to drive a sulfur-iodine (SI) thermochemical hydrogen production process has been the subject of a U.S. Department of Energy sponsored Nuclear Engineering Research Initiative (NERI) project led by General Atomics, with participation from the Idaho National Laboratory (INL) and Texas A and M University. While the focus of much of the initial work was on the SI thermochemical production of hydrogen, recent activities included development of a preconceptual design for an integral HTE hydrogen production plant driven by the process heat and electricity produced by a 600 MW MHR. This paper describes ATHENA analyses performed to evaluate alternative primary system cooling configurations for the MHR to minimize peak reactor vessel and core temperatures while achieving core helium outlet temperatures in the range of 900-1000 deg. C that are needed for the efficient production of hydrogen using either the SI or HTE process. The cooling schemes investigated are intended to ensure peak fuel temperatures do not exceed specified limits under normal or transient upset conditions, and that reactor vessel temperatures do not exceed American Society of Mechanical Engineers (ASME) code limits for steady-state or transient conditions using standard light water reactor vessel materials. Preconceptual designs for SI and HTE hydrogen production plants driven by one or more 600 MW MHRs at helium outlet temperatures in the range of 900-1000 deg. C are described and compared. An initial SAPHIRE model to evaluate the reliability, maintainability, and availability of the SI hydrogen production plant is also described. Finally, a preliminary flowsheet for a conceptual design of an HTE hydrogen production plant coupled to a 600 MW modular helium reactor is presented and

Status on development and verification of reactivity initiated accident analysis code for PWR (NODAL3)

International Nuclear Information System (INIS)

Peng Hong Liem; Surian Pinem; Tagor Malem Sembiring; Tran Hoai Nam

2015-01-01

A coupled neutronics thermal-hydraulics code NODAL3 has been developed based on the nodal few-group neutron diffusion theory in 3-dimensional Cartesian geometry for a typical pressurized water reactor (PWR) static and transient analyses, especially for reactivity initiated accidents (RIA). The spatial variables are treated by using a polynomial nodal method (PNM) while for the neutron dynamic solver the adiabatic and improved quasi-static methods are adopted. A simple single channel thermal-hydraulics module and its steam table is implemented into the code. Verification works on static and transient benchmarks are being conducting to assess the accuracy of the code. For the static benchmark verification, the IAEA-2D, IAEA-3D, BIBLIS and KOEBERG light water reactor (LWR) benchmark problems were selected, while for the transient benchmark verification, the OECD NEACRP 3-D LWR Core Transient Benchmark and NEA-NSC 3-D/1-D PWR Core Transient Benchmark (Uncontrolled Withdrawal of Control Rods at Zero Power). Excellent agreement of the NODAL3 results with the reference solutions and other validated nodal codes was confirmed. (author)

Parallel GPU implementation of PWR reactor burnup

International Nuclear Information System (INIS)

Heimlich, A.; Silva, F.C.; Martinez, A.S.

2016-01-01

Highlights: • Three GPU algorithms used to evaluate the burn-up in a PWR reactor. • Exhibit speed improvement exceeding 200 times over the sequential. • The C++ container is expansible to accept new nuclides chains. - Abstract: This paper surveys three methods, implemented for multi-core CPU and graphic processor unit (GPU), to evaluate the fuel burn-up in a pressurized light water nuclear reactor (PWR) using the solutions of a large system of coupled ordinary differential equations. The reactor physics simulation of a PWR reactor spends a long execution time with burnup calculations, so performance improvement using GPU can imply in better core design and thus extended fuel life cycle. The results of this study exhibit speed improvement exceeding 200 times over the sequential solver, within 1% accuracy.

Conceptual design of fusion experimental reactor (FER)

International Nuclear Information System (INIS)

1984-03-01

A conceptual design study (option C) has been carried out for the fusion experimental reactor (FER). In addition to design of the tokamak reactor and associated systems based on the reference design specifications, feasibility of a water-shield reactor concept was examined as a topical study. The design study for the reference tokamak reactor has produced a reactor concept for the FER, along with major R D items for the concept, based on close examinations on thermal design, electromagnetics, neutronics and remote maintenance. Particular efforts have been directed to the area of electromagnetics. Detailed analyses with close simulation models have been performed on PF coil arrangements and configurations, shell effects of the blanket for plasma position unstability, feedback control, and eddy currents during disruptions. The major design specifications are as follows; Peak fusion power 437 MW Major radius 5.5 m Minor radius 1.1 m Plasma elongation 1.5 Plasma current 5.3 MA Toroidal beta 4 % Field on axis 5.7 T (author)

Accelerated irradiation test of Gundremmingen reactor vessel trepan material

Energy Technology Data Exchange (ETDEWEB)

Hawthorne, J.R. [Materials Engineering Associates, Inc., Lanham, MD (United States)

1992-08-01

Initial mechanical properties tests of beltline trepanned from the decommissioned KRB-A pressure vessel and archive material irradiated in the UBR test reactor revealed a major anomaly in relative radiation embrittlement sensitivity. Poor correspondence of material behavior in test vs. power reactor environments was observed for the weak test orientation (ASTL C-L) whereas correspondence was good for the strong orientation (ASTM C-L). To resolve the anomaly directly, Charpy-V specimens from a low (essentially-nil) fluence region of the vessel were irradiated together with archive material at 279{degrees}C in the UBR test reactor. Properties tests before UBR irradiation revealed a significant difference in 41-J transition temperature and upper shelf energy level between the materials. However, the materials exhibited essentially the same radiation embrittlement sensitivity (both orientations), proving that the anomaly is not due to a basic difference in material irradiation resistances. Possible causes of the original anomaly and the significance to NRC Regulatory Guide 1.99 are discussed.

Accelerated irradiation test of gundremmingen reactor vessel trepan material

International Nuclear Information System (INIS)

Hawthorne, J.R.

1992-08-01

Initial mechanical properties tests of beltline trepanned from the decommissioned KRB-A pressure vessel and archive material irradiated in the UBR test reactor revealed a major anomaly in relative radiation embrittlement sensitivity. Poor correspondence of material behavior in test vs. power reactor environments was observed for the weak test orientation (ASTL C-L) whereas correspondence was good for the strong orientation (ASTM C-L). To resolve the anomaly directly, Charpy-V specimens from a low (essentially-nil) fluence region of the vessel were irradiated together with archive material at 279 degrees C in the UBR test reactor. Properties tests before UBR irradiation revealed a significant difference in 41-J transition temperature and upper shelf energy level between the materials. However, the materials exhibited essentially the same radiation embrittlement sensitivity (both orientations), proving that the anomaly is not due to a basic difference in material irradiation resistances. Possible causes of the original anomaly and the significance to NRC Regulatory Guide 1.99 are discussed

Estudio de criticidad del reactor MSBR con SCALE

OpenAIRE

Criado Martín, Alejandro Fernando

2011-01-01

El presente proyecto final de carrera se enmarca en el convenio de colaboración entre el Consejo de Seguridad Nuclear (CSN) y la Universitat Politècnica de Catalunya (UPC) para la realización de proyectos en el ámbito de la seguridad nuclear y la protección radiológica. El proyecto estudia la criticidad del reactor Molten Salt Breeder Reactor (MSBR) mediante el código de simulación SCALE. El MSBR es un reactor de sales fundidas concebido y diseñado por ORNL, con una composic...

MIT pebble bed reactor project

Energy Technology Data Exchange (ETDEWEB)

Kadak, Andrew C. [Massachusetts Institute of Technology, Cambridge (United States)

2007-03-15

The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis.

MIT pebble bed reactor project

International Nuclear Information System (INIS)

Kadak, Andrew C.

2007-01-01

The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis

Gas cooled thermal reactors with high temperatures (VHTR)

International Nuclear Information System (INIS)

Bouchter, J.C.; Dufour, P.; Guidez, J.; Latge, C.; Renault, C.; Rimpault, G.; Vasile, A.

2014-01-01

VHTR is one of the 6 concepts retained for the 4. generation of nuclear reactors, it is an upgraded version of the HTR-type reactor (High Temperature Reactors). 5 HTR reactors were operated in the world in the eighties, now 2 experimental HTR are working in China and Japan and 2 HTR with an output power of 100 MWe are being built in China. The purpose of the VHTR is to provide an helium at very high temperatures around 1000 Celsius degrees that could be used directly in a thermochemical way to produce hydrogen for instance. HTR reactors are interesting in terms of safety but it does not optimise the consumption of uranium and the production of wastes. This article presents a brief historical account of HTR-type reactors and their main design and safety features. The possibility of using HTR to burn plutonium is also presented as well as the possibility of closing the fuel cycle and of using thorium-uranium fuel. (A.C.)

Pyrolysis of Rubber in a Screw Reactor

Science.gov (United States)

Lozhechnik, A. V.; Savchin, V. V.

2016-11-01

On the basis of an analysis of thermal methods described in the literature and from the results of experimental investigations of steam conversion, the authors have developed and created a facility for thermal processing of rubber waste. Rubber crumb was used as the raw material; the temperature in the reactor was 500°C; nitrogen, steam, and a mixture of light hydrocarbons (noncondensable part of pyrolysis products) represented the working medium. The pyrolysis yielded 36-38% of a solid fraction, 54-56% of a liquid hydrocarbon fraction, and 6-9% of noncondensable gases. Changes in the composition of the gas mixture have been determined at different stages of processing. Gas chromatography of pyrolysis gases has shown that the basic gases produced by pyrolysis are H2 and hydrocarbons C2H4, C3H6, C3H8, C4H8, C2H6, C3H6O2, and C4H10, and a small amount of H2S, CO, and CO2. Noncondensable gases will be used as a fuel to heat the reactor and to implement the process.

Irradiated graphite studies prior to decommissioning of G1, G2 and G3 reactors

International Nuclear Information System (INIS)

Bonal, J.P.; Vistoli, J.Ph.; Combes, C.

2005-01-01

G1 (46 MW th ), G2 (250 MW th ) and G3 (250 MW th ) are the first French plutonium production reactors owned by CEA (Commissariat a l'Energie Atomique). They started to be operated in 1956 (G1), 1959 (G2) and 1960 (G3); their final shutdown occurred in 1968, 1980 and 1984 respectively. Each reactor used about 1200 tons of graphite as moderator, moreover in G2 and G3, a 95 tons graphite wall is used to shield the rear side concrete from neutron irradiation. G1 is an air cooled reactor operated at a graphite temperature ranging from 30 C to 230 C; G2 and G3 are CO 2 cooled reactors and during operation the graphite temperature is higher (140 C to 400 C). These reactors are now partly decommissioned, but the graphite stacks are still inside the reactors. The graphite core radioactivity has decreased enough so that a full decommissioning stage may be considered. Conceming this decommissioning, the studies reported here are: (i) stored energy in graphite, (ii) graphite radioactivity measurements, (iii) leaching of radionuclide ( 14 C, 36 Cl, 63 Ni, 60 Co, 3 H) from graphite, (iv) chlorine diffusion through graphite. (authors)

Fast pyrolysis of Miscanthus sinensis in fluidized bed reactors: Characteristics of product yields and biocrude oil quality

International Nuclear Information System (INIS)

Bok, Jin Pil; Choi, Hang Seok; Choi, Joon Weon; Choi, Yeon Seok

2013-01-01

In the present work, fast pyrolysis of Miscanthus sinensis was performed and the product yields and properties of the resulting biocrude oil were determined for varying reactor configurations and pyrolysis temperatures. Two types of reactors (rectangular and cylindrical fluidized beds) were adopted, and pyrolysis temperature was increased from 400 °C to 550 °C. Based on the results, it was found that the reaction temperature greatly influenced the product yield and the characteristics of biocrude oil. The highest yield of biocrude oil for the rectangular reactor was 48.9 wt.%, produced at 500 °C, and the highest yield for the cylindrical reactor was 50.01 wt.%, produced at 450 °C. Additionally, the biocrude oil yield in the rectangular reactor sharply decreased when reaction temperature was increased to 550 °C, while only a slight decrease was observed in the cylindrical reactor. From GC/MS analysis, biocrude oil was found to contain various chemical components, such as nonaromatic ketones, furans, sugars, lignin-derived phenols, guaiacols and syringols. In particular, the sugar content of the biocrude oil produced in rectangular reactor (2.11–9.35 wt.%) was generally lower than that produced in the cylindrical reactor (7.93–10.79 wt.%). - Highlights: • Fast pyrolysis of Miscanthus sinensis was performed in two fluidized bed reactors to obtain biocrude oil. • The yield and characteristics of the biocrude oil were scrutinized with changing reaction temperature and reactor type. • The reaction temperature was found to be the most influencing parameter for the fast pyrolysis reaction. • The different heating rate caused by reactor type has an effect on the final product yield and characteristics

Analysis and upgrade of instrumentation and control systems for the modernization of research reactors

International Nuclear Information System (INIS)

1988-01-01

This document provides assistance in the review and planning process for the upgrade of instrumentation and control systems (I and C systems) and related safety features of the reactor protection system for research reactors. In the interest of safety a need was realized to evaluate the performance of outdated I and C systems. An advisory group was assembled to develop guidelines and to provide recommendations for the upgrade of I and C systems. The recommendations on I and C systems upgrade contained in this document were developed by the advisory group using as guidelines the established safety criteria and operating standards for research reactors. 24 refs

Gas-cooled Fast Reactor (GFR) fuel and In-Core Fuel Management

International Nuclear Information System (INIS)

Weaver, K.D.; Sterbentz, J.; Meyer, M.; Lowden, R.; Hoffman, E.; Wei, T.Y.C.

2004-01-01

The Gas-Cooled Fast Reactor (GCFR) has been chosen as one of six candidates for development as a Generation IV nuclear reactor based on: its ability to fully utilize fuel resources; minimize or reduce its own (and other systems) actinide inventory; produce high efficiency electricity; and the possibility to utilize high temperature process heat. Current design approaches include a high temperature (2 850 C) helium cooled reactor using a direct Brayton cycle, and a moderate temperature (550 C - 650 C) helium or supercritical carbon dioxide (S-CO 2 ) cooled reactor using direct or indirect Brayton cycles. These design choices have thermal efficiencies that approach 45% to 50%, and have turbomachinery sizes that are much more compact compared to steam plants. However, there are challenges associated with the GCFR, which are the focus of current research. This includes safety system design for decay heat removal, development of high temperature/high fluence fuels and materials, and development of fuel cycle strategies. The work presented here focuses on the fuel and preliminary in-core fuel management, where advanced ceramic-ceramic (cercer) dispersion fuels are the main focus, and average burnups to 266 M Wd/kg appear achievable for the reference Si C/(U,TRU)C block/plate fuel. Solid solution (pellet) fuel in composite ceramic clad (Si C/Si C) is also being considered, but remains as a backup due to cladding fabrication challenges, and high centerline temperatures in the fuel. (Author)

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure

DEFF Research Database (Denmark)

Nielsen, H.B.; Mladenovska, Zuzana; Westermann, Peter

2004-01-01

A two-stage 68degreesC/55degreesC anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68degrees......, was compared with a conventional single-stage reactor running at 55degreesC with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single......-stage reactor. The 68degreesC reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic...

Modern design and safety analysis of the University of Florida Training Reactor

International Nuclear Information System (INIS)

Jordan, K.A.; Springfels, D.; Schubring, D.

2015-01-01

Highlights: • A new safety analysis of the University of Florida Training Reactor is presented. • This analysis uses modern codes and replaces the NRC approved analysis from 1982. • Reduction in engineering margin confirms that the UFTR is a negligible risk reactor. • Safety systems are not required to ensure that safety limits are not breached. • Negligible risk reactors are ideal for testing digital I&C equipment. - Abstract: A comprehensive series of neutronics and thermal hydraulics analyses were conducted to demonstrate the University of Florida Training Reactor (UFTR), an ARGONAUT type research reactor, as a negligible risk reactor that does not require safety-related systems or components to prevent breach of a safety limit. These analyses show that there is no credible UFTR accident that would result in major fuel damage or risk to public health and safety. The analysis was based on two limiting scenarios, whose extremity bound all other accidents of consequence: (1) the large step insertion of positive reactivity and (2) the release of fission products due to mechanical damage to a spent fuel plate. The maximum step insertion of positive reactivity was modeled using PARET/ANL software and shows a maximum peak fuel temperature of 283.2 °C, which is significantly below the failure limit of 530 °C. The exposure to the staff and general public was calculated for the worst-case fission product release scenario using the ORIGEN-S and COMPLY codes and was shown to be 6.5% of the annual limit. Impacts on reactor operations and an Instrumentation & Control System (I&C) upgrade are discussed

Modern design and safety analysis of the University of Florida Training Reactor

Energy Technology Data Exchange (ETDEWEB)

Jordan, K.A., E-mail: kjordan@ufl.edu [University of Florida, 106 UFTR Bldg., PO Box 116400, Gainesville, FL 32611-6400 (United States); Springfels, D., E-mail: dspringfels@ufl.edu [University of Florida, 106 UFTR Bldg., PO Box 116400, Gainesville, FL 32611-6400 (United States); Schubring, D., E-mail: dlschubring@ufl.edu [University of Florida, 202 Nuclear Science Building, PO Box 118300, Gainesville, FL 32611-8300 (United States)

2015-05-15

Highlights: • A new safety analysis of the University of Florida Training Reactor is presented. • This analysis uses modern codes and replaces the NRC approved analysis from 1982. • Reduction in engineering margin confirms that the UFTR is a negligible risk reactor. • Safety systems are not required to ensure that safety limits are not breached. • Negligible risk reactors are ideal for testing digital I&C equipment. - Abstract: A comprehensive series of neutronics and thermal hydraulics analyses were conducted to demonstrate the University of Florida Training Reactor (UFTR), an ARGONAUT type research reactor, as a negligible risk reactor that does not require safety-related systems or components to prevent breach of a safety limit. These analyses show that there is no credible UFTR accident that would result in major fuel damage or risk to public health and safety. The analysis was based on two limiting scenarios, whose extremity bound all other accidents of consequence: (1) the large step insertion of positive reactivity and (2) the release of fission products due to mechanical damage to a spent fuel plate. The maximum step insertion of positive reactivity was modeled using PARET/ANL software and shows a maximum peak fuel temperature of 283.2 °C, which is significantly below the failure limit of 530 °C. The exposure to the staff and general public was calculated for the worst-case fission product release scenario using the ORIGEN-S and COMPLY codes and was shown to be 6.5% of the annual limit. Impacts on reactor operations and an Instrumentation & Control System (I&C) upgrade are discussed.

Gas-solid hydroxyethylation of potato starch in a stirred vibrating fluidized bed reactor

NARCIS (Netherlands)

Kuipers, N.J M; Stamhuis, Eize; Beenackers, A.A C M

A novel reactor for modifying cohesive C-powders such as in the gas-solid hydroxyethylation of semidry potato starch is characterized, the so-called stirred vibrating fluidized bed reactor. Good fluidization characteristics are obtained in this reactor for certain combinations of stirring and

Fast pyrolysis of sugarcane and cassava residues in a free-fall reactor

International Nuclear Information System (INIS)

Pattiya, Adisak; Sukkasi, Sittha; Goodwin, Vituruch

2012-01-01

Fast pyrolysis of agricultural residues from sugarcane and cassava plantations was carried out in a laboratory-scale free-fall reactor unit. The objectives of this work were to investigate the effects of biomass types and pyroysis conditions, such as reactor temperature, condensation temperature, nitrogen flow rate and run duration, on pyrolysis product distribution, as well as to study the basic properties of the products. The results showed that all of the parameters affected the product distribution. The optimum reactor temperatures for maximising bio-oil yield were in the range of 350–450 °C. About 70 wt% of bio-oil yield could be obtained by pyrolysis of cassava stalk at a reactor temperature of 450 °C and a primary condensation temperature of 10 °C. It was also found that the minimum flow rate of nitrogen for obtaining high bio-oil yield was 1.5 l/min. The product characterisation showed that the bio-oil and char produced from the agricultural residues with the free-fall reactor unit were to a certain extent similar to those produced from different types of biomass with different types of pyrolysis reactor configurations. -- Highlights: ► Fast pyrolysis of sugarcane and cassava agricultural residues was carried out in a laboratory-scale free-fall reactor unit. ► The effects of process parameters on product yields were investigated. ► The process parameters included reactor temperature, condensation temperature, nitrogen flow rate and run duration. ► Basic properties of pyrolysis products were examined.

Application of a bistable convection loop to LMFBR [liquid metal fast breeder reactor] emergency core cooling

International Nuclear Information System (INIS)

Anand, G.; Christensen, R.N.

1990-01-01

The concept of passive safety features for nuclear reactors has been developed in recent years and has gained wide acceptance. A literature survey of current reactors with passive features indicates that these reactors have some passive features but still do not fully meet the design objectives. Consider a current liquid-metal reactor design like PRISM. During normal operation, liquid sodium enters the reactor at ∼395 degree C and exits at ∼550 degree C. In the event of loss of secondary cooling with or without scram, the primary coolant (liquid sodium) initially acts as a heat sink and its temperature increases. For events without scram, the negative reactivity induced by the increase in temperature shuts the reactor down. When the average temperature of the sodium reaches ∼600 to 650 degree C, it overflows from the reactor vessel, activating the auxiliary cooling system. The auxiliary cooling system uses natural circulation of air around the reactor guard vessel. An alternative to the current design incorporates a bistable convection loop (BCL). The incorporation of the BCL concept remarkably improves the safety of the nuclear reactors. Application of the BCL concept to liquid-metal fast breeder reactors is described in this paper

Wear plates control rod guide tubes top internal reactor vessel C. N. VANDELLOS II

International Nuclear Information System (INIS)

2010-01-01

The guide tubes for control rods forming part of the upper internals of the reactor vessel, its function is to guide the control rod to permit its insertion in the reactor core. These guide tubes are suspended from the upper support plate which are fixed by bolts and extending to the upper core plate which is fastened by clamping bolts (split pin) to prevent lateral displacement of the guide tubes, while allowing axial expansion.

Influence of cold work to increase swelling of pure iron irradiated in the BR-10 reactor to ∼6 and ∼25 dpa at ∼400 deg. C

International Nuclear Information System (INIS)

Dvoriashin, A.M.; Porollo, S.I.; Konobeev, Yu.V.; Garner, F.A.

2000-01-01

Irradiation of pure iron in several starting conditions at 400 deg. C has been conducted in the BR-10 fast reactor. Contrary to expectations, cold working appears to significantly accelerate the onset of void swelling. When compared to a similar experiment conducted in this reactor at the same time, it appears that iron experiences a rather long transient duration before the onset of steady-state swelling. The transient appears to be shortened by both cold-working and lower atomic displacement rates

Metallic materials corrosion problems in molten salt reactors

International Nuclear Information System (INIS)

Chauvin, G.; Dixmier, J.; Jarny, P.

1977-01-01

The USA forecastings concerning the molten salt reactors are reviewed (mixtures of fluorides containing the fuel, operating between 560 and 700 0 C). Corrosion problems are important in these reactors. The effects of certain characteristic factors on corrosion are analyzed: humidity and metallic impurities in the salts, temperature gradients, speed of circulation of salts, tellurium from fission products, coupling. In the molten fluorides and experimental conditions, the materials with high Ni content are particularly corrosion resistant alloys (hastelloy N). The corrosion of this material is about 2.6 mg.cm -2 at 700 0 C [fr

Stress analysis of two-dimensional C/C composite components for HTGR's core restraint techanism

International Nuclear Information System (INIS)

Satoshi Hanawa; Taiju Shibata; Jyunya Sumita; Masahiro Ishihara; Tatsuo Iyoku; Kazuhiro Sawa

2005-01-01

Carbon fiber reinforced carbon matrix composite (C/C composite) is one of the most promising materials for HTGRs core components due to their high strength as well as high temperature resistibility. One of the most attractive applications of C/C composite is the core restraint mechanism. The core restraint mechanism is located around the reflector block and it works to tighten reactor core blocks so as to restrict un-supposition flow pass of coolant gas (bypass flow) in the core. The restriction of bypass flow reads to the high efficiency of coolant flow rate inside of the reactor core. For the future HTGRs and VHTR (Very High Temperature Reactor), it is important to develop the core restraint mechanism with C/C composite substitute for metallic materials as used for HTTR. For the application of C/C composite to core restraint mechanism, it is important to investigate the applicability of C/C composite in viewpoint of structural integrity. In the present study, supposing the application of 2D-C/C composite to core restraint mechanism, thermal stress behavior was analyzed by considering the thickness of the C/C composite and the gap between reflector block and core restraint. It was shown from the thermal stress analysis that the circumferential stress decreases with increasing the gap and that the restraint force increases with increasing the thickness. By optimizing the thickness of C/C composite and gap between reflector block and core restraint, the C/C composite is applicable to the core restraint mechanism. (authors)

Computer code for the thermal-hydraulic analysis of ITU TRIGA Mark-II reactor

International Nuclear Information System (INIS)

Ustun, G.; Durmayaz, A.

2002-01-01

Istanbul Technical University (ITU) TRIGA Mark-II reactor core consists of ninety vertical cylindrical elements located in five rings. Sixty-nine of them are fuel elements. The reactor is operated and cooled with natural convection by pool water, which is also cooled and purified in external coolant circuits by forced convection. This characteristic leads to consider both the natural and forced convection heat transfer in a 'porous-medium analysis'. The safety analysis of the reactor requires a thermal-hydraulic model of the reactor to determine the thermal-hydraulic parameters in each mode of operation. In this study, a computer code cooled TRIGA-PM (TRIGA - Porous Medium) for the thermal-hydraulic analysis of ITU is considered. TRIGA Mark-II reactor code has been developed to obtain velocity, pressure and temperature distributions in the reactor pool as a function of core design parameters and pool configuration. The code is a transient, thermal-hydraulic code and requires geometric and physical modelling parameters. In the model, although the reactor is considered as only porous medium, the other part of the reactor pool is considered partly as continuum and partly as porous medium. COMMIX-1C code is used for the benchmark purpose of TRIGA-PM code. For the normal operating conditions of the reactor, estimations of TRIGA-PM are in good agreement with those of COMMIX-1C. After some more improvements, this code will be employed for the estimation of LOCA scenario, which can not be analyses by COMMIX-1C and the other multi-purpose codes, considering a break at one of the beam tubes of the reactor

Neutron streaming evaluation for the DREAM fusion power reactor

International Nuclear Information System (INIS)

Seki, Yasushi; Nishio, Satoshi; Ueda, Shuzo; Kurihara, Ryoichi

2000-01-01

Aiming at high degree of safety and benign environmental effect, we have proposed a tokamak fusion reactor concept called DREAM, which stands for DRastically EAsy Maintenance Reactor. The blanket structure of the reactor is made from very low activation SiC/SiC composites and cooled by non-reactive helium gas. High net thermal efficiency of about 50% is realized by 900 C helium gas and high plant availability is possible with simple maintenance scheme. In the DREAM Reactor, neutron streaming is a big problem because cooling pipes with diameter larger than 80 cm are used for blanket heat removal. Neutron streaming through the cooling pipes could cause hot spots in the superconducting magnets adjacent to the cooling pipes to shorten the magnet lifetime or increase cryogenic cooling requirement. Neutron streaming could also activate components such as gas turbine further away from the fusion plasma. The effect of neutron streaming through the helium cooling pipes was evaluated for the two types of cooling pipe extraction scheme. The result of a preliminary calculation indicates the gas turbine activation prohibits personnel access in the case of inboard pipe extraction while with additional shielding measures, limited contact maintenance is possible in the case of outboard extraction. (author)

Effect of temperature on selenium removal from wastewater by UASB reactors.

Science.gov (United States)

Dessì, Paolo; Jain, Rohan; Singh, Satyendra; Seder-Colomina, Marina; van Hullebusch, Eric D; Rene, Eldon R; Ahammad, Shaikh Ziauddin; Carucci, Alessandra; Lens, Piet N L

2016-05-01

The effect of temperature on selenium (Se) removal by upflow anaerobic sludge blanket (UASB) reactors treating selenate and nitrate containing wastewater was investigated by comparing the performance of a thermophilic (55 °C) versus a mesophilic (30 °C) UASB reactor. When only selenate (50 μM) was fed to the UASB reactors (pH 7.3; hydraulic retention time 8 h) with excess electron donor (lactate at 1.38 mM corresponding to an organic loading rate of 0.5 g COD L(-1) d(-1)), the thermophilic UASB reactor achieved a higher total Se removal efficiency (94.4 ± 2.4%) than the mesophilic UASB reactor (82.0 ± 3.8%). When 5000 μM nitrate was further added to the influent, total Se removal was again better under thermophilic (70.1 ± 6.6%) when compared to mesophilic (43.6 ± 8.8%) conditions. The higher total effluent Se concentration in the mesophilic UASB reactor was due to the higher concentrations of biogenic elemental Se nanoparticles (BioSeNPs). The shape of the BioSeNPs observed in both UASB reactors was different: nanospheres and nanorods, respectively, in the mesophilic and thermophilic UASB reactors. Microbial community analysis showed the presence of selenate respirers as well as denitrifying microorganisms. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microbial succession within an anaerobic sequencing batch biofilm reactor (ASBBR treating cane vinasse at 55ºC

Directory of Open Access Journals (Sweden)

Maria Magdalena Ferreira Ribas

2009-08-01

Full Text Available The aim of this work was to investigate the anaerobic biomass formation capable of treating vinasse from the production of sugar cane alcohol, which was evolved within an anaerobic sequencing batch biofilm reactor (ASBBR as immobilized biomass on cubes of polyurethane foam at the temperature of 55ºC. The reactor was inoculated with mesophilic granular sludge originally treating poultry slaughterhouse wastewater. The evolution of the biofilm in the polyurethane foam matrices was assessed during seven experimental phases which were thus characterized by the changes in the organic matter concentrations as COD (1.0 to 20.0 g/L. Biomass characterization proceeded with the examination of sludge samples under optical and scanning electron microscopy. The reactor showed high microbial morphological diversity along the trial. The predominance of Methanosaeta-like cells was observed up to the organic load of 2.5 gCOD/L.d. On the other hand, Methanosarcinalike microorganisms were the predominant archaeal population within the foam matrices at high organic loading ratios above 3.3 gCOD/L.d. This was suggested to be associated to a higher specific rate of acetate consumption by the later organisms.Este trabalho investigou a formação de um biofilme anaeróbio capaz de tratar vinhaça da produção de álcool de cana-de-açúcar, que evoluiu dentro de um reator operado em bateladas seqüenciais com biofilme (ASBBR tendo a biomassa imobilizada em cubos de espuma de poliuretano na temperatura de 55ºC. O reator foi inoculado com lodo granular mesofílico tratando água residuária de abatedouro de aves. A evolução do biofilme nas matrizes de espuma de poliuretano foi observada durante sete fases experimentais que foram caracterizadas por mudanças nas concentrações de matéria orgânica como DQO (1,0 a 20,0 g/L. A caracterização da biomassa foi feita por exames de amostras do lodo em microscopia ótica e eletrônica de varredura. O reator apresentou

Nuclear reactor

International Nuclear Information System (INIS)

Hattori, Sadao; Sato, Morihiko.

1994-01-01

Liquid metals such as liquid metal sodium are filled in a reactor container as primary coolants. A plurality of reactor core containers are disposed in a row in the circumferential direction along with the inner circumferential wall of the reactor container. One or a plurality of intermediate coolers are disposed at the inside of an annular row of the reactor core containers. A reactor core constituted with fuel rods and control rods (module reactor core) is contained at the inside of each of the reactor core containers. Each of the intermediate coolers comprises a cylindrical intermediate cooling vessels. The intermediate cooling vessel comprises an intermediate heat exchanger for heat exchange of primary coolants and secondary coolants and recycling pumps for compulsorily recycling primary coolants at the inside thereof. Since a plurality of reactor core containers are thus assembled, a great reactor power can be attained. Further, the module reactor core contained in one reactor core vessel may be small sized, to facilitate the control for the reactor core operation. (I.N.)

The CAREM reactor and present currents in reactor design

International Nuclear Information System (INIS)

Ordonez, J.P.

1990-01-01

INVAP has been working on the CAREM project since 1983. It concerns a very low power reactor for electrical energy generation. The design of the reactor and the basic criteria used were described in 1984. Since then, a series of designs have been presented for reactors which are similar to CAREM regarding the solutions presented to reduce the chance of major nuclear accidents. These designs have been grouped under different names: Advanced Reactors, Second Generation Reactors, Inherently Safe Reactors, or even, Revolutionary Reactors. Every reactor fabrication firm has, at least, one project which can be placed in this category. Presently, there are two main currents of Reactor Design; Evolutionary and Revolutionary. The present work discusses characteristics of these two types of reactors, some revolutionary designs and common criteria to both types. After, these criteria are compared with CAREM reactor design. (Author) [es

Pressurized heavy-water reactor safety

International Nuclear Information System (INIS)

Pease, L.; Wilson, R.

1977-09-01

CANDU-PWR type reactors routinely release small amounts of radioactive liquids and gases and large quantities of low-grade waste heat. Radioactive emissions are usually below 1% of the derived release limits based on ICRP limits. Waste heat is common to all power plants and is not foreseen as a problem in Canadian conditions. Risk analysis shows a very low accident probability for CANDU type reactors. Multiple barriers to release of radionuclides, quality assurance, control, and inspection, containment systems, the shutdown system, the ECCS, and leak-before-break design, would all combine to mitigate the effects of an accident. (E.C.B.)

Irradiation routine in the IPR-R1 Triga reactor

International Nuclear Information System (INIS)

Maretti Junior, F.

1980-01-01

Information about irradiations in the IPR-R1 TRIGA reactor and procedures necessary for radioisotope solicitation are presented All procedures necessary for asking irradiation in the reactor, shielding types, norms of terrestrial and aerial expeditions, payment conditions, and catalogue of disposable isotopes with their respective saturation activities are described. (M.C.K.)

Instrumentation and control for reactor power setback in PFBR

International Nuclear Information System (INIS)

Upadhyay, Chandra Kant; Vasal, Tanmay; Nagaraj, C.P.; Madhusoodanan, K.

2013-01-01

In Prototype Fast Breeder Reactor (PFBR), a 500 MWe plant, Reactor Power Setback is a special operation envisaged for bulk power reduction on occurrence of certain events in Balance of Plant. The bulk power reduction requires a large negative reactivity perturbation if reactor is operating on nominal power. This necessitates a reliable monitoring system with fault tolerant I and C architecture in order to inhibit reactor SCRAM on negative reactivity trip signal. The impact of above events on the process is described. Design of a functional prototype module to carry out RPSB logic operation and its interface with other instruments has been discussed. (author)

Predictions on an HTR coolant composition after operational experience with experimental reactors

International Nuclear Information System (INIS)

Nieder, R.

1981-01-01

Long-term operational experience of the HTR experimental reactors Dragon (1966 - 1975), Peach Bottom (1967 - 1974) and AVR (since 1967) has yielded a large number of common quantitative and qualitative results about the sources and behaviour of helium impurities in the primary circuits. Additional information has also been obtained from experiments made at the three reactors. The results at the AVR are particularly interesting because the gas outlet temperature can be varied from 770 0 C to 950 0 C when the reactor power is kept constant. Hence they can be studied according to the temperature dependence of all chemical reactions. It should be possible to apply the results from the operating measurements and experiments made at the reactors, in particular the interrelation of the impurity concentrations, to future reactors. The absolute values of these impurity concentrations are obtained first and foremost by the corresponding helium purification constants

Towards a reduced activation structural materials database for fusion DEMO reactors

International Nuclear Information System (INIS)

Moeslang, A.; Diegele, E.; Laesser, R.; Klimiankou, M.; Lindau, R.; Materna-Morris, E.; Rieth, M.; Lucon, E.; Petersen, C.; Schneider, H.-C.; Pippan, R.; Rensman, J.W.; Schaaf, B. van der; Tavassoli, F.

2005-01-01

The development of First Wall, Blanket and Divertor materials which are capable of withstanding many years the high neutron and heat fluxes, is a critical path to fusion power. Therefore, the timely availability of a sound materials database has become an indispensable element in international fusion road maps. In order to provide materials design data for short term needs of ITER Test Blanket Modules and for a DEMOnstration fusion reactor, a wealth of R and D results on the European reduced activation ferritic-martensitic steel EUROFER, and on oxide dispersion strengthened variants are being characterized, mainly in the temperature window 250-650 deg. C. The characterisation includes irradiations up to 15 dpa in the mixed spectrum reactor HFR and up to 75 dpa in the fast breeder reactor BOR60. Industrial EUROFER-batches of 3.5 and 7.5 tons have been produced with a variety of semi-finished, quality-assured product forms. To increase thermal efficiency of blankets, high temperature resistant SiC f /SiC channel inserts for liquid metal coolant tubes are also developed. Regarding radiation damage resistance, a broad based reactor irradiation programs counts several steps from ≤5dpa (ITER TBMs) up to 75 dpa (DEMO). For the European divertor designers, a materials data base is presently being set up for pure W and W alloys, and related reactor irradiations are foreseen with temperatures from 650-1000 deg. C. (author)

Development of the design of the High Temperature Gas Cooled Reactor experiment

International Nuclear Information System (INIS)

Lockett, G.E.; Huddle, R.A.U.

1960-01-01

Early in 1956 a small team was formed at the Atomic Energy Research Establishment, Harwell, to investigate the possibilities of the High Temperature Gas Cooled (H.T.G.C.) Reactor System. Although the primary objective of this team was to carry out a feasibility study of the system as a whole, it soon became apparent that, in addition to design studies and economic surveys of power producing reactors, the most appropriate approach to such a novel system was to carry out a design study of a relatively small (10 to 20 M.W.) Reactor Experiment, together with the necessary research and development work associated with such a reactor. This work proceeded within the U.K.A.E.A. during the three following years, and it was felt that realistic design proposals could be put forward with sufficient confidence to justify the detailed design and construction of a 20 M.W. Reactor Experiment. In April 1959 responsibility for this Reactor Experiment was taken over by the O.E.E.C. High Temperature Gas Cooled Reactor Project, the DRAGON Project, at the Atomic Energy Establishment, Winfrith, Dorset. In this Paper the research, development, and design work is reviewed, and the proposals for the Reactor Experiment are summarised. (author)

Irradiation Creep and Swelling of Russian Ferritic-Martensitic Steels Irradiated to Very High Exposures in the BN-350 Fast Reactor at 305-335 degrees C

International Nuclear Information System (INIS)

Konobeev, Yury V.; Dvoriashin, Alexander M.; Porollo, S.I.; Shulepin, S.V.; Budylkin, N.I.; Mironova, Elena G.; Garner, Francis A.

2003-01-01

Russian ferritic/martensitic (F/M) steels EP-450, EP-852 and EP-823 were irradiated in the BN-350 fast reactor in the form of gas-pressurized creep tubes. The first steel is used in Russia for hexagonal wrappers in fast reactors. The other steels were developed for compatibility with Pb-Bi coolants and serve to enhance our understanding of the general behavior of this class of steels. In an earlier paper we published data on irradiation creep of EP-450 and EP-823 at temperatures between 390 and 520C, with dpa levels ranging from 20 to 60 dpa. In the current paper new data on the irradiation creep and swelling of EP-450 and EP-852 at temperatures between 305 and 335C and doses ranging from 61 to 89 dpa are presented. Where comparisons are possible, it appears that these steels exhibit behavior that is very consistent with that of Western steels. Swelling is relatively low at high neutron exposure and confined to temperatures <420C, but may be camouflaged somewhat by precipitation-related densification. These irradiation creep studies confirm that the creep compliance of F/M steels is about one-half that of austenitic steels.

Study on introduction scenario of the high temperature gas-cooled reactor hydrogen cogeneration system (GTHTR300C). Part 1

International Nuclear Information System (INIS)

Nishihara, Tetsuo; Takeda, Tetsuaki

2005-09-01

Japan Atomic Energy Research Institute is carrying out the research and development of the high temperature gas-cooled reactor hydrogen cogeneration system (GTHTR300C) aiming at the practical use around 2030. Preconditions of GTHTR300C introduction are the increase of hydrogen demand and the needs of new nuclear power plants. In order to establish the introduction scenario, it should be clarified that the operational status of existing nuclear power plants, the introduction number of fuel cell vehicles as a main user of hydrogen and the capability of hydrogen supply by existing plants. In this report, estimation of the nuclear power plants that will be decommissioned with a high possibility by 2030 and selection of the model district where the GTHTR300C can be introduced as an alternative system are conducted. Then the hydrogen demand and the capability of hydrogen supply in this district are investigated and the hydrogen supply scenario in 2030 is considered. (author)

Overview of materials research for fusion reactors

International Nuclear Information System (INIS)

Muroga, T.; Gasparotto, M.; Zinkle, S.J.

2002-01-01

Materials research for fusion reactors is overviewed from Japanese, EU and US perspectives. Emphasis is placed on programs and strategies for developing blanket structural materials, and recent highlights in research and development for reduced activation ferritic martensitic steels, vanadium alloys and SiC/SiC composites, and in mechanistic experimental and modeling studies. The common critical issue for the candidate materials is the effect of irradiation with helium production. For the qualification of materials up to the full lifetime of a DEMO and Power Plant reactors, an intense neutron source with relevant fusion neutron spectra is crucial. Elaborate use of the presently available irradiation devices will facilitate efficient and sound materials development within the required time scale

High-throughput reactor system with individual temperature control for the investigation of monolith catalysts

Science.gov (United States)

Dellamorte, Joseph C.; Vijay, Rohit; Snively, Christopher M.; Barteau, Mark A.; Lauterbach, Jochen

2007-07-01

A high-throughput parallel reactor system has been designed and constructed to improve the reliability of results from large diameter catalysts such as monoliths. The system, which is expandable, consists of eight quartz reactors, 23.5mm in diameter. The eight reactors were designed with separate K type thermocouples and radiant heaters, allowing for the independent measurement and control of each reactor temperature. This design gives steady state temperature distributions over the eight reactors within 0.5°C of a common setpoint from 50to700°C. Analysis of the effluent from these reactors is performed using rapid-scan Fourier transform infrared (FTIR) spectroscopic imaging. The integration of this technique to the reactor system allows a chemically specific, truly parallel analysis of the reactor effluents with a time resolution of approximately 8s. The capabilities of this system were demonstrated via investigation of catalyst preparation conditions on the direct epoxidation of ethylene, i.e., on the ethylene conversion and the ethylene oxide selectivity. The ethylene, ethylene oxide, and carbon dioxide concentrations were calibrated based on spectra from FTIR imaging using univariate and multivariate chemometric techniques. The results from this analysis showed that the calcination conditions significantly affect the ethylene conversion, with a threefold increase in the conversion when the catalyst was calcined for 3h versus 12h at 400°C.

Photocatalytic reactors for treating water pollution with solar illumination: a simplified analysis for n-steps flow reactors with recirculation

Energy Technology Data Exchange (ETDEWEB)

Sagawe, G.; Bahnemann, D. [Universitaet Hannover (Germany). Institut fuer Technische Chemie; Brandi, R.J.; Cassano, A.E. [INTEC Universidad Nacional del Litoral and CONICET, Sante Fe (Argentina)

2005-09-01

The concentration of dissolved oxygen in water, in equilibrium with atmospheric air (ca. 8 ppm at 20{sup o}C), defines the limits of all practical oxidizing processes for removing pollutants in photocatalytic reactors. To solve this limitation, an alternative approach to that of a continuously aerated reactor is the use of a recirculating system with aeration performed after every cycle at the reactor entering stream. As defined by the nature of a single recirculating step (the need of a reactor operation at a rather low concentration range), this procedure results in a very low photonic efficiency (thus requiring a large photon collecting area and consequently increasing the capital cost). The design engineer will have to resort to a series of several reactors with recirculation. This solution may then lead to a very high Photonic Efficiency for the entire process (i.e., a reduced light harvesting area) at the price of an increase in the required capital cost (due to the larger number of reactors). This paper provides a very simple analysis and analytical expressions that can be used to estimate, for a desired degree of degradation, a trade-off solution between a high number of reactors and a very large surface area to collect the solar photons. (author)

Neutron behavior, reactor control, and reactor heat transfer. Volume four

International Nuclear Information System (INIS)

Anon.

1986-01-01

Volume four covers neutron behavior (neutron absorption, how big are nuclei, neutron slowing down, neutron losses, the self-sustaining reactor), reactor control (what is controlled in a reactor, controlling neutron population, is it easy to control a reactor, range of reactor control, what happens when the fuel burns up, controlling a PWR, controlling a BWR, inherent safety of reactors), and reactor heat transfer (heat generation in a nuclear reactor, how is heat removed from a reactor core, heat transfer rate, heat transfer properties of the reactor coolant)

Luncheon address: Development of the CANDU reactor

International Nuclear Information System (INIS)

Bain, A.S.

1997-01-01

The paper is a highlight of the some of the achievements in the development of the CANDU Reactor, taken from the book C anada Enters the Nuclear Age . The CANDU reactor is one of Canada's greatest scientific/engineering achievements, that started in the 1940's and bore fruit with the reactors of the 60's, 70's, and 80's. The Government decided in the 1950's to proceed with a demonstration nuclear power reactor (NPD), AECL invited 7 Canadian corporations to bid on a contract to design and construct the NPD plant. General Electric was selected. A utility was also essential for participation and Ontario Hydro was chosen. In May 1957 it was concluded that the minimum commercial size would be about 200MWe and it should use horizontal pressure tubes to contain the fuel and pressurized heavy water coolant. The book also talks of standard out-reactor components such as pumps, valves, steam generators and piping. A major in-reactor component of interest was the fuel, fuel channels and pressure tubes. A very high level of cooperation was required for the success of the CANDU program

Design study of 'HIBLIC-I' reactor cavity

International Nuclear Information System (INIS)

Fujiie, Y.

1984-01-01

A preliminary conceptual design of a reactor cavity for HIBLIC-1, a heavy ion fusion reactor system, was carried out. Design efforts have been concentrated mainly on the feasibility study of the physical scenario adopted and also on the system integration of the structures and components into a compact reactor cavity. The design features of the reactor are a compact reactor cavity, maximum coolant temperature up to 500 deg C, the protection of the sacrificial wall and cavity wall from radiation, the protection of the sacrificial wall from the pressure transient due to rapid heating, the selection of a ferritic steel HT-9 as the structural material and impurity control, and tritium breeding and recovery. The purpose of this paper is to describe the outline of the reactor cavity design of HIBLIC-1. The objectives of the preliminary conceptual design were to propose the idea and concept in order to constitute the physical scenario without contradiction and to find out the critical and fundamental problems to be studied in future. The cavity configuration and dynamics, tritium breeding and radiation damage, the behavior of a structural material in liquid lithium and tritium recovery are reported. (Kako, I.)

Reactor science and technology: operation and control of reactors

International Nuclear Information System (INIS)

Qiu Junlong

1994-01-01

This article is a collection of short reports on reactor operation and research in China in 1991. The operation of and research activities linked with the Heavy Water Research Reactor, Swimming Pool Reactor and Miniature Neutron Source Reactor are briefly surveyed. A number of papers then follow on the developing strategies in Chinese fast breeder reactor technology including the conceptual design of an experimental fast reactor (FFR), theoretical studies of FFR thermo-hydraulics and a design for an immersed sodium flowmeter. Reactor physics studies cover a range of topics including several related to work on zero power reactors. The section on reactor safety analysis is concerned largely with the assessment of established, and the presentation of new, computer codes for use in PWR safety calculations. Experimental and theoretical studies of fuels and reactor materials for FBRs, PWRs, BWRs and fusion reactors are described. A final miscellaneous section covers Mo-Tc isotope production in the swimming pool reactor, convective heat transfer in tubes and diffusion of tritium through plastic/aluminium composite films and Li 2 SiO 3 . (UK)

Nuclear power reactors

International Nuclear Information System (INIS)

1982-11-01

After an introduction and general explanation of nuclear power the following reactor types are described: magnox thermal reactor; advanced gas-cooled reactor (AGR); pressurised water reactor (PWR); fast reactors (sodium cooled); boiling water reactor (BWR); CANDU thermal reactor; steam generating heavy water reactor (SGHWR); high temperature reactor (HTR); Leningrad (RMBK) type water-cooled graphite moderated reactor. (U.K.)