Energy Technology Data Exchange (ETDEWEB)

The corrosion resistance of steel-reinforced mortar specimens made from alinite cement was investigated using ordinary Portland cement (OPC) specimens as reference. The specimens were prepared and exposed in three different environments: continuous exposure in tap water, interrupted exposure in tap water, and interrupted exposure in 3.5% NaCl solution. The steel weight loss and the half cell potential were measured vs. exposure time, up to the age of 12 months. Pore solution extraction and analysis and porosity determination were also performed. In continuous exposure in tap water, alinite cement provided adequate protection against corrosion. In interrupted exposure in tap water, a higher corrosion was observed for alinite cement compared to OPC. In the case of interrupted exposure in 3.5% NaCl solution, the simultaneous action of free chlorides and oxygen resulted in the depassivation of steel ...

British Library Electronic Table of Contents (United Kingdom)

Glass fiber-reinforced polymer (GFRP) reinforcing bars were used recently as main reinforcement for concrete structures. The noncorrodible GFRP material exhibits linear-elastic stress-strain characteristics up to failure with relatively low modulus of elasticity compared to steel. This raises concerns on GFRP performance in structures where energy dissipation, through plastic behavior, is required. The objective of this research project is to assess the seismic behavior of concrete beam-column joints reinforced with GFRP bars and stirrups. Two full-scale exterior T-shaped beam-column joint prototypes are constructed and tested under simulated seismic load conditions. One prototype is totally reinforced with GFRP bars and stirrups, while the other one is reinforced with steel. The experimen...

International Nuclear Information System (INIS)

Bases of the algorithm for assessing the reinforcement status in reinforced concrete products by gamma-absorption method are presented. Analytical equations are obtained for estimation of error of the parameter characterizing the degree of reinforcement destruction. It is recommended to use high-energy Bremsstrahlung sources-betatrons of 4-10 MeV maximum energy for testing products of 500-600 mm thick. Linear radiation attenuation factor (LAF) of concrete in estimated equation is replaced by effective LAF of concrete, and LAF of reinforcement and corrosion materials - by differential LAF. Corresponding LAF of nonevident form in the algorithm is assessed by the results of processing of direct-shadow radiographs of defectometers

Energy Technology Data Exchange (ETDEWEB)

Four commercial stainless steels (mat. Nos. 1.4539, 1.4586, 1.4571 and 1.4462) were tested in 96% and 90% sulfuric acid of 80/sup 0/C as to their corrosion fatigue strength by subjecting notched round bars to the rotary bending test. At the same time, the efficiency of anodic protection was examined. With all four steels, the alternating bending strength obtained in the air is essentially reduced. The semiaustenitic steel Nr. 1.4462 shows a lower corrosion fatigue strength than the three austenitic steels. Although making the corrosion fatigue strength of steels better calculable, anodic protection proves insufficient to completely prevent notched round bars from corrosion fatigue in concentrated sulfuric acid.

International Nuclear Information System (INIS)

Under the current design philosophy, reactor structures are to be designed to withstand large inelastic deformation caused by strong and severe ground motion. The design of the main structural elements and their connections are to be such that they always fail in ductile mode. This will ensure large energy absorption capacity of the structures under seismic excitation and avoid sudden and brittle failure of the structure. Over the years, a number of experimental investigations have been carried out on RC beam- column joints to study their behaviour and strength. However, these studies mostly pertain to small scale joints of moment resisting frame of residential buildings and commercial complexes. Information on full scale joints existing in NPP structures are scanty. Therefore, experimental programme was planned in the laboratory to construct identical large sized joints with the same reinforcement percentage and detail as that of the existing joints in NPP ...

International Nuclear Information System (INIS)

Beta C trademark, a metastable beta titanium alloy developed by RMI Titanium Company, continues to be used in new applications due to its excellent mechanical properties and resistance to corrosion. New data in this paper include mechanical properties in large sections, cold drawn bar and welds. Fatigue crack growth and corrosion data are added to supplement previously published data.

Energy Technology Data Exchange (ETDEWEB)

The report traces the documented incidences of brittle fracture in composite suspension insulators for use on high voltage transmission lines, and presents the subsequent investigations. It describes the part played by electrical activity, stress corrosion and humidity, and compares similar failures that have taken place in electric traction insulators. It then goes on to review related work on the humidity effects, stress corrosion, fatigue and partial discharges in glass fiber reinforced plastics in general. The final section summarizes the present understanding of the problem and the various measures taken by different manufactures to avoid it in the future. The need for acceptance criteria in this respect is outlined.

Science.gov (United States)

... Soviet standard or specification number for each reinforced plastic is included ... The tabular data contains general applications of reinforced plastics. ...

International Nuclear Information System (INIS)

In order to investigate the role of amorphous SiO2 particles in corrosion and wear resistance of Ni-based metal matrix composite alloying layer, the amorphous nano-SiO2 particles reinforced Ni-based composite alloying layer has been prepared by double glow plasma alloying on AISI 316L stainless steel surface, where Ni/amorphous nano-SiO2 was firstly predeposited by brush plating. The composition and microstructure of the nano-SiO2 particles reinforced Ni-based composite alloying layer were analyzed by using SEM, TEM and XRD. The results indicated that the composite alloying layer consisted of ?-phase and amorphous nano-SiO2 particles, and under alloying temperature (1000 deg. C) condition, the nano-SiO2 particles were uniformly distributed in the alloying layer and still kept the amorphous structure. The corrosion resistance of composite alloying layer was investigated by an electrochemical method in ...

International Nuclear Information System (INIS)

A series of tests has been carried out to determine the operating conditions required to remove the corrosion deposit from samples cut from Winfrith Steam Generating Heavy Water Reactor (WSGHWR) primary circuit pipework by submerged water jetting. Two types of samples were used - one set subjected to the normal annual reactor decontamination using TURCO reagents, the other set having been given a LOMI treatment in addition. Tests showed that useful decontamination factors could be achieved on both types of sample, but significantly less severe operating conditions were required to decontaminate the LOMI treated samples. A decontamination factor of 10 was achieved on TURCO treated samples at 360 Bar; only 200 Bar was required to achieve the same decontamination factor on LOMI treated samples. No metal erosion of the stainless steel substrate was found to occur at these pressures. (author).

Science.gov (United States)

Not Available

Science.gov (United States)

... Keywords: Ferrocement; Floating concrete structures; Ships; Barges; and Offshore platforms. Descriptors : *REINFORCED ...

Energy Technology Data Exchange (ETDEWEB)

Alloying elements such as Fe and Cr are generally considered to be effective even in small quantities for corrosion resistance of Zircaloy-4. The maximum total solubility of Fe + Cr in a Zr-Sn matrix has been reported to be very low. Therefore, most of these elements are observed in the form of ternary Zr-Fe-Cr-type precipitates. To clarify the effects of precipitates on corrosion property, Zr-1.3 Sn-(Fe,Cr) alloys containing Fe + Cr from 45 up to 180 ppm (the Fe to Cr ratio is about 2) were melted from pure zirconium (X-bar Zr and EB-Zr) and pure alloying elements. They were subjected to corrosion testing in 633 K water and microstructural analysis. It was found that precipitate-free materials showed much larger weight gains than precipitate-containing materials even at the same alloy compositions. Subsequently, a corrosion test on the precipitate-free material galvanically coupled ...

Energy Technology Data Exchange (ETDEWEB)

Stress corrosion cracks have been discovered in Group Distribution Headers (GDH) at the Ignalina and Chernobyl Nuclear Power Plants. This increases the probability that a guillotine pipe break can occur that creates a whipping pipe (GDH) with the potential to damage surrounding structures-i.e. adjacent GDH and its attached piping or adjacent reinforced concrete compartment wall. The GDH is the most important component for reactor safety in case of an accident. Emergency Core Cooling System (ECCS) piping is connected to the GDH piping such that, during an accident, coolant passes from the ECSS into the GDH. Presented in this paper is the transient analysis of a Group Distribution Header following a guillotine break at the blind end of the header. Using a very conservative force loading function, the transient response of a whipping RBMK-1500 GDH along with neighboring concrete walls and pipelines is obtained using finite element methodology. The ...

British Library Electronic Table of Contents (United Kingdom)

Excellent mechanical properties and corrosion resistance combined with low weight qualify ?-titanium materials for lightweight applications in aviation, automotive and energy engineering. Thus far, actual applications of these materials have been limited due to high material costs and limited processing knowledge. One approach for developing resource-efficient manufacturing methods is the application of incremental forming methods. This article focuses on the development of the incremental spin extrusion process, which creates hollow profiles from solid bars. This method allows hollow shape manufacturing with a much higher flexibility than other forming methods and a significantly improved material utilization in comparison to machining methods, such as deep hole drilling. Beta-titanium al...

International Nuclear Information System (INIS)

A consistent mathematical derivation is given for the Sommerfeld fine structure electromagnetic coupling 1/?-bar 0=?0-bar 1/137.036. Following 't Hooft's holographic principle two complimentary forms of the derivation are given both leading to the E(?) theoretical value, namely ?-bar 0=(20)(1/?)4=137.082039311. The experimental value is subsequently found by projection as ?-bar 0(exp)=137/[cos(?/?-bar 0)]-bar 137.036.

Science.gov (United States)

Page 1. How do we impact corrosion? US Army Corrosion Summit Feb. ... Page 4. Leaders in Corrosion Control Technology Impact of Corrosion - $$ ...

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

An assessment of the joint shear strength of exterior concrete beam-column joints reinforced internally with Glass Fibre Reinforced Polymer (GFRP) reinforcements under monotonically increasing load on beams keeping constant load on columns is carried out in this study. Totally eighteen numbers of specimens are cast and tested for different parametric conditions like beam longitudinal reinforcement ratio, concrete strength, column reinforcement ratio, joint aspect ratio and influence of the joint stirrups at the joint. Also finite element analysis is performed to simulate the behaviour of the beam-column joints under various parametric conditions. Based on this study, a modified design equation is proposed for assessing the joint shear strength of the GFRP reinforced beam-column specimens b...

Science.gov (United States)

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network ...

Science.gov (United States)

This report is a continuation of the former efforts to elucidate the behavior of ferrocement concrete in static and dynamic stress fields. The influence of various reinforcements on pre and post cracking of thin sections forms the main topic of this repor...

UK PubMed Central (United Kingdom)

Choice procedures have indicated that the relative reinforcing effectiveness of opioid drugs increases during opioid withdrawal. The demand curve, an absolute measure of reinforcer value, has not been...Full Text Available

Science.gov (United States)

... Problems investigated in various basic hollowness ratios include ultimate compressive strength, fatigue properties, buckling characteristics, and ...

International Nuclear Information System (INIS)

... Netherlands Kormendy, J. Dominion Astrophysical Observatory, Victoria, British

Energy Technology Data Exchange (ETDEWEB)

A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

CERN Document Server

In order to perform a detailed study of the stellar kinematics in the vertical axis of bars, we obtained high signal-to-noise spectra along the major and minor axes of the bars in a sample of 14 face-on galaxies, and used them to determine the line of sight stellar velocity distribution, parameterized as Gauss-Hermite series. With these data, we developed a diagnostic tool that allows one to distinguish between recently formed and evolved bars, as well as estimate their ages, assuming that bars form in vertically thin disks, recognizable by low values for the vertical velocity dispersion sigma_z. Through N-body realizations of bar unstable disk galaxies we could also check the time scales involved in the processes which give bars an important vertical structure. We show that sigma_z in evolved bars is roughly around 100 Km/s, which ...

CERN Document Server

Structural steels with improved atmospheric corrosion resistance

International Science & Technology Center (ISTC)

Development of the Corrosion Protection Technology for Special Steels and Alloys

CERN Document Server

Based on 58 million J/Psi events collected with the BESII detector at the BEPC, the baryon pair processes J/Psi to $\\Sigma^+ \\bar{\\Sigma}^-$ and J/Psi to $\\Xi^0 \\bar{\\Xi}^0$ are observed for the first time. The branching fractions are measured to be ${\\cal B}(J/Psi to \\Sigma^+ \\bar{\\Sigma}^-)=(1.50\\pm 0.10\\pm 0.22)\\times 10^{-3}$ and ${\\cal B}(J/Psi to \\Xi^0 \\bar{\\Xi}^0)=(1.20\\pm 0.12\\pm 0.21)\\times 10^{-3}$, where the first errors are statistical and the second ones are systematic.

Wastenet

Hexavalent chromium in corrosion preventive coating 64 ...To prevent corrosion of rims, weights can be provided with a coating. ...integrated clips brought up technical problems due to corrosion

Wastenet

... Corrosion Inhibitors Equipment on Environmental Expert Find and compare a variety of corrosion inhibitors equipment on the world's largest environmental industry portal. View ...

Energy Technology Data Exchange (ETDEWEB)

Reinforced (heterogel) silicate materials containing an amorphous and a crystalline phase are being used more and more industry. Such systems are energetically unsaturated and therefore promising for use in catalysts. The authors used two reinforced materials as supports: an aluminosilicate containing a zeolite (the cracking catalyst, tseokar) and asbestos-containing aluminosilicate. The active component was introduced by impregnation, and this was followed by heat treatment during which the chemical composition and porous structure were formed. The impregnating mixture consisted of solutions of potassium sulfate and vanadate of the required concentrations. The testing shows that reinforced heterogel systems are promising as support materials for sulfuric acid catalysts.

Science.gov (United States)

... Composite sandwich panels with fiber reinforced plastic (FRP) faces and low 3 density foam cores are fast becoming the structural material of ...

Science.gov (United States)

... heavy divisions in the Contingency Corps should ... During Operation Desert Shield the 82nd Airborne Division initially deployed a reinforced attack ...

Science.gov (United States)

... kg/m3 density. The Rohacell foam displayed an average ultimate compressive strength of 1546 kPa. The maximum load ...

British Library Electronic Table of Contents (United Kingdom)

North American design codes are now committed to the development of load and resistance factor design (LRFD) for reinforced soil structures including internal stability limit states. Reliability-based analysis is required to carry out these calibrations. A framework for LRFD calibration has been proposed by the writers that requires bias statistics for load and resistance terms for each limit state function. In this paper the formulation of the limit state for reinforcement tensile rupture is developed and the component strength-reduction bias statistics identified. The paper describes how to compute bias statistics from project-specific installation damage trials for use in reliability-based design for the reinforcement rupture limit state or using data from multiple sources for LRFD cali...

Science.gov (United States)

A common reinforced liner material is a cloth formed of PTFE fibers and fiber of ... and ablation protection provided. All of these methods of thermal ..... The influence of fiber content on the microstructures of the composites is ...

CERN Document Server

Anodic protection

Science.gov (United States)

Scratch and Corrosion Resistance of an Aluminum Flange with an Electron Beam Modified Seal Edge

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... FIELD CORROSION TESTS WERE MADE DURING THE VOYAGES OF THE SCIENTIFIC-RESEARCH SHIPS ACADEMICIAN VERNADSKII AND ...

International Nuclear Information System (INIS)

Pitting corrosion is a kind of electrolytic corrosion by which the surface of a material is locally affected owing to inhomogeneities on the part of the material or medium. The paper deals briefly with questions relating to the importance, to parameters medium or materialwise, influence on production and construction, as well as the general conditions for pitting corrosion. In particular oxygen corrosion in unalloyed and low-alloy steel, and pitting corrosion in ferritic chromium-steel and austenitic chromium-nickel (molybdenum) steel is described. (DG).

Energy Technology Data Exchange (ETDEWEB)

By using the continuation theorem of coincidence degree theory and constructing suitable Lyapunov functions, we study the existence and stability of periodic solution for shunting inhibitory cellular neural networks (SICNNs) with delays x-bar {sub ij}(t)=-a{sub ij}(t)x{sub ij}(t)--bar B{sup kl}-bar Nr(i,j)B{sub ij}{sup kl}(t)f{sub ij}(x{sub kl}(t))x{sub ij}(t)--bar C{sup kl}-bar Nr(i,j)C{sub ij}{sup kl}(t)g{sub ij}(x{sub kl}(t-{tau}{sub kl}))x{sub ij}(t)+L{sub ij}(t)

International Nuclear Information System (INIS)

The evolution of intergranular lattice strains in a textured, forged bar (Bar) sample of the #alpha# - #beta# titanium alloy Ti-6Al-4V has been characterised using in situ X-ray diffraction. A two-phase elastic-plastic self-consistent (EPSC) model has been developed to rationalise the results. Of the orientations analysed, it is found that the #left brace#2 0 0#right brace# #beta# orientation is the most compliant and that load partitions to this orientation during plasticity. The results from the bar material have then been used to predict the response of unidirectionally rolled plate (UD) Ti-6Al-4V. It is predicted that the residual lattice strains in the #left brace#101-bar0#right brace# and #left brace#112-bar0#right brace# orientations will be significantly higher in the UD material.

CERN Document Server

Present in over 45% of local spirals, boxy and peanut-shaped bulges are generally interpreted as edge-on bars and may represent a key phase in the evolution of bulges. Aiming to test such claims, the kinematic properties of self-consistent 3D N-body simulations of bar-unstable disks are studied. Using Gauss-Hermite polynomials to describe the stellar kinematics, a number of characteristic bar signatures are identified in edge-on disks: 1) a major-axis light profile with a quasi-exponential central peak and a plateau at moderate radii (Freeman Type II profile); 2) a ``double-hump'' rotation curve; 3) a sometime flat central velocity dispersion peak with a plateau at moderate radii and occasional local central minimum and secondary peak; 4) an h3-V correlation over the projected bar length. All those kinematic features are spatially correlated and can easily be understood from the orbital structure of ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion failures in circuits of foreign NPPs are considered. According to American statistics there are more corrosion failures in two-circuit NPPs than in NPPs with one circuit. Steam generators mostly suffer from ''corrosion denting''. Lately pitting corrosion becomes a potentially serious problem. Steam generator vertical tubes are mainly subjected to this corrosion type. Attention is drawn to intercrystalline corrosion. The causes of corrosion are described. The problem of optimization of structural materials is discussed to reduce corrosion failures as well as other methods of decreasing corrosion failures. Organization of nondestructive testing, increased requirements to water and steam purity are of great importance.

Energy Technology Data Exchange (ETDEWEB)

Discontinuously reinforced aluminium-based composites containing particulate or whisker SiC reinforcements at different volume fractions, were produced via a powder-route. Isothermal creep tests have been carried out at 270, 300 and 320 C. During these tests axial and transverse strains were monitored using a non-contacting laser scanning extensometer arrangement. At the same time neutron diffraction has been used to measure the elastic phase strain evolution with composite creep deformation. It was found that after the initial loading the phase strains remained essentially constant during primary and secondary creep. This indicates that the initial matrix/reinforcement inelastic misfits remain largely unchanged, probably due to the setting up of a dynamic equilibrium between misfit generation and stress relaxation. For each system, the neutron data has been combined with Eshelby modelling to obtain a measure of the load ...

Science.gov (United States)

With an increased use of fiber reinforced concrete in structural applications, proper characterization techniques and development of design guides are needed. This dissertation presents a multi-scale modeling approach for fiber and fabric reinforced cement-based composites. A micromechanics-based model of the yarn pullout mechanism due to the failure of the interfacial zone is presented. The effect of mechanical anchorage of transverse yarns is simulated using nonlinear spring elements. The yarn pullout mechanism was used in a meso-scale modeling approach to simulate the yarn bridging force in the crack evolution process. The tensile stress-strain response of a tension specimen that experiences distributed cracking can be simulated using a generalized finite difference approach. The stiffness degradation, tension stiffening, crack spacing evolution, and crack width characteristics of cement composites can be derived using matrix, interface and ...

International Nuclear Information System (INIS)

Briefly described is knowledge of crevice corrosion, corrosion cracking and denting. In evaluating the corrosion resistance of steam generator materials it is necessary to distinguish corrosion problems caused by the primary coolant eide and by the secondary circuit side. At present tubes are manufactured of 7 austenitic alloys of a different chemical composition, and available information shows that views on their corrosion resistance differ. Greatest attention has been devoted to corrosion cracking in the presence of HaOH. Findings related to I-600, I-800, I-690 and AISI 316 are given. Corrodibility by sulfur-containing products is now being studied, namely the intercrystalline corrosion cracking caused by the presence of H_2S_4O_6. Knowledge gained in this respect is summed up. (J.P.).

Energy Technology Data Exchange (ETDEWEB)

Thermogalvanic corrosion of St3 steel in a temperature range from 25 to 50{degrees}C with a 3.84{degrees}C/cm gradient was studied in a neutral media flow. It is shown that the thermogalvanic effect on the pitting corrosion of water-cooled heat exchangers is decisive but dual. Depending on the composition of the cooling medium, thermogalvanic corrosion may either enhance (0.5 M NaCl) or inhibit (tap water) pitting corrosion.

Energy Technology Data Exchange (ETDEWEB)

Since first PWR in Japan started commercial operation in 1970, we have encountered the various modes of corrosion on primary and secondary side components. We have paid much efforts for resolving these corrosion problems, that is, investigating the causes of corrosion and establishing the countermeasures for these corrosion. We summarize these efforts in this article. (author)

Energy Technology Data Exchange (ETDEWEB)

In the present work, electrochemical measurements and corrosion tests in NaCl solutions were carried out to study the effect of aging treatments on pitting corrosion behavior in a 8090 alloy and its high purity Al-Li binary alloy analogue. The pitting corrosion characteristics and corrosion resistance of the 8090 alloy have been determined in relation to precipitation microstructures. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The warm caliber rolling was experimented using the AZ31 magnesium alloy round bar of 20 mm in diameter machined from cast ingot materials. In warm caliber rolling in final size of 10 mm in diameter at 623 K via 8passes, each width-spreading, the change of each microstructure, X-ray analysis of final texture and final mechanical properties were investigated. Microstructure, texture and mechanical properties of warm caliber rolled round bar at 473 K via latter 4passes were compared with those at 623 K consistently. Obtained results are as follows: (1) The width-spreading in caliber rolling of round bar is relatively large, compared with that in flat rolling of the flat bar. The largeness of width-spreading of round bar makes the shape control of cross section difficult, and causes the cracks around the free surface. (2) Finer microstructure and inclined c axis of hexagonal lattice of ...

CERN Document Server

From this vast subject, I will pick out and review three specific topics, namely the formation and evolution of bars, the formation of bulges, and the evolution during multiple major mergers. Bars form naturally in galactic discs. Their evolution is driven by the exchange of angular momentum within the galaxy. This is emitted mainly by near-resonant material in the inner disc (bar), and is absorbed by near-resonant material in the outer disc and in the halo. As a result of this, the bar becomes stronger and rotates slower. Bulges are not a homogeneous class of objects. Based on their formation history, one can distinguish three types. Classical bulges are mainly formed before the actual disc component, from collapses or mergers and the corresponding dissipative processes. Boxy/peanut bulges are parts of bars seen edge-on. Finally, disc-like bulges are formed by the inflow of ...

CERN Document Server

We discuss the evolution of a disc galaxy due to the formation of a bar and, subsequently, a peanut. After the formation stage there is still considerable evolution, albeit slower. In purely stellar cases the pattern speed of the bar decreases with time, while its amplitude grows. However, if a considerable gaseous component is present in the disc, the pattern speed may increase with time, while the bar strength may decrease. In some cases the gas can be brought sufficiently close to the center to create a strong central concentration, which, in turn, may modify the properties of the bar. More violent evolution can take place during interactions, so that some disc substructures can be either formed or destroyed in a time scale which is small compared to a Hubble time. These include spirals, bars, bridges, tails, rings, thick discs and bulges. In some cases interactions may lead to ...

Energy Technology Data Exchange (ETDEWEB)

We summarize our lattice QCD study of the form factor at zero recoil in the decay {bar B} {yields} D*{ell}{bar {nu}}. After careful consideration of all sources of systematic uncertainty, we find, h{sub A{sub 1}}(1) = 0.913{sub -17-30}{sup +24+17}, where the first uncertainty is from statistics and fitting while the second combined uncertainty is from all other systematic effects.

Science.gov (United States)

Are there wave-cut shore lines? Ripple marks? Scablands? Gravel and sand bars? .... these pictures will nally tie together the view from Mars' sur- ...

Energy Technology Data Exchange (ETDEWEB)

We perform an optimal-observable analysis of the final charged-lepton/b-quark momentum distributions in {gamma}{gamma}{yields}t t-bar {yields}lX/bX for various beam polarizations in order to study possible anomalous t t-bar {gamma}, tbW and {gamma}{gamma}H couplings, which could be generated by SU(2) x U(1) gauge-invariant dimension-6 effective operators. We find optimal beam polarizations that will minimize the uncertainty in determination of those non-standard couplings. We also compare e e-bar and {gamma}{gamma} colliders from the viewpoint of the anomalous-top-quark-coupling determination.

Science.gov (United States)

star formation. To either side of the center, a small bar of dust and gas is helping to fuel the new stars. NASA's Jet Propulsion Laboratory, Pasadena, Calif., manages the...

British Library Electronic Table of Contents (United Kingdom)

Experiments have been conducted to study the effect of injection pressure on the combustion process and exhaust emissions of a direct injection diesel engine fueled with Orange Skin Powder Diesel Solution (OSPDS). Earlier investigation by the authors revealed that 30% OSPDS was optimum for better performance and emissions. In the present investigation the injection pressure was varied with 30% OSPDS and the combustion, performance and emissions characteristics were compared with those of diesel fuel. The different injection pressures studied were 215bar, 235bar and 255bar. The results showed that the cylinder pressure with 30% OSPDS at 235bar fuel injection pressure, was higher than that of diesel fuel as well as at other injection pressures. Similarly, the ignition delay was longer and wi...

CERN Document Server

Shaping has proven to be a powerful but precarious means of improving reinforcement learning performance. Ng, Harada, and Russell (1999) proposed the potential-based shaping algorithm for adding shaping rewards in a way that guarantees the learner will learn optimal behavior. In this note, we prove certain similarities between this shaping algorithm and the initialization step required for several reinforcement learning algorithms. More specifically, we prove that a reinforcement learner with initial Q-values based on the shaping algorithm's potential function make the same updates throughout learning as a learner receiving potential-based shaping rewards. We further prove that under a broad category of policies, the behavior of these two learners are indistinguishable. The comparison provides intuition on the theoretical properties of the shaping algorithm as well as a suggestion for a simpler method for capturing the ...

International Nuclear Information System (INIS)

#alpha#/#beta# sialon based composites containing silicon nitride whisker and silicon carbide platelet were fabricated by hot pressing. Effect of the reinforcing agents on the #alpha# to #beta# phase transformation of the sialon as well as on the mechanical properties was investigated. Silicon nitride whisker and silicon carbide platelet promoted the phase transformation. TEM/EDS analysis revealed that the grain containing the whisker had 'core-rim' structure; core being high purity Si_3N_4 whisker and rim being #beta#-sialon. Flexural strength of the composite decreased with the reinforcement addition which, on the other hand, improved fracture toughness of it. High temperature strength was measured at 1300 deg C to be about 130 MPa lower than that measured at RT for the whisker reinforced composite. (author).

International Nuclear Information System (INIS)

Research highlights: #-># The Y-intermetallic can accelerate corrosion and Y can increase the protectiveness of the surface layer. #-># In 0.1 M NaCl, the corrosion rate of Mg-Y alloys increased with increasing Y due to the Y intermetallic. #-># In 0.1 M NaCl, there was filiform corrosion. #-># In 0.1 M Na_2SO_4, the corrosion rate of Mg-Y alloys decreased with increasing Y in the range 3-7%Y. #-># Hydrogen evolution was observed from particular parts of the alloy surface. - Abstract: Corrosion of Mg-Y alloys was studied using electrochemical evaluations, immersion tests and direct observations. There were two important effects. In 0.1 M NaCl, the corrosion rate increased with increasing Y content due to increasing amounts of the Y-containing intermetallic. In 0.1 M Na_2SO_4, the corrosion rate decreased with increasing Y ...

Energy Technology Data Exchange (ETDEWEB)

Gas transmission pipelines are susceptible to both internal (gas side) and external (soil side) corrosion attack. Internal corrosion is caused by the presence of salt laden moisture, CO{sub 2}, H{sub 2}S, and perhaps O{sub 2} in the natural gas. Internal corrosion usually manifests itself as general corrosion. However, the presence of chlorides in entrained water also can lead to pitting corrosion damage. The electrochemical noise technique can differentiate general from localized corrosion and provide estimates of corrosion rates without external perturbation of the corroding system. It is increasingly being applied to field and industrial installations for in situ corrosion monitoring. It has been used here to determine its suitability for monitoring internal and external corrosion damage on gas ...

International Nuclear Information System (INIS)

Information is presented concerning solute concentration in a porous layer; solute concentration in a packed crevice; corrosion of a packed carbon steel crevice in NaCl-O"2 solutions; and effect of copper on corrosion in NaCl-O"2 solutions.

Science.gov (United States)

Carbon steel, copper, zinc and aluminium samples were exposed in different sizes with known ambient parameters in Gran Canaria Island and atmospheric corrosion was investigated. Weight-loss measurements used to determine corrosion damage were complemented...

International Nuclear Information System (INIS)

Three different techniques for pitting corrosion potential measurement on austenitic stainless steel (Fe18Cr10Ni) were compared: conventional polarization method, a new Avesta electrochemical corrosion measurement cell and a scratch technique. Special attention was paid to the effects of crevice corrosion during pitting corrosion potential measurement and to their elimination. Development of a rapid test technique for reliable pitting corrosion potential determination was aimed at and resulted from comparison of the different techniques.

Energy Technology Data Exchange (ETDEWEB)

Superheater corrosion causes vast annual losses to the power companies. If the corrosion could be reliably predicted, new power plants could be designed accordingly, and knowledge of fuel selection and determination of process conditions could be utilized to minimize superheater corrosion. If relations between inputs and the output are poorly known, conventional models depending on corrosion theories will fail. A prediction model based on a neural network is capable of learning from errors and improving its performance as the amount of data increases. The neural network developed during this study predicts superheater corrosion with 80 % accuracy at early stage of the project. (orig.) 10 refs.

Energy Technology Data Exchange (ETDEWEB)

The rate of corrosion of hardened cement paste in solutions of nitric, hydrochloric, sulfuric, acetic and formic acids was compared. Corrosion in solutions of acetic and nitric acids with different concentrations was studied in more detail. The results made it possible to obtain the relationships expressing the influence of concentration and the time of action of acid solutions on the depth of corrosion. The rates of corrosion in nitric acid solutions during the first 3 years were about 2 to 4 times that in acetic acid solutions, depending on the concentration.

Energy Technology Data Exchange (ETDEWEB)

Carbon steel, copper, zinc and aluminium samples were exposed in different sizes with known ambient parameters in Gran Canaria Island and atmospheric corrosion was investigated. Weight-loss measurements used to determine corrosion damage were complemented with metallographic and XP S determination in order to characterize the structure and morphology of surface corrosion products. The ambient aggressiveness could be well evaluated from meteorological and pollution data. All atmospheric corrosion and environmental data were statistically processed for establishing general corrosion damage functions for carbon steel, copper, aluminium and zinc in terms of Gran Canaria extreme meteorological and pollution parameters. (Author)

Science.gov (United States)

... 1. IE1O and IM'15 exposed to field corrosion tests at five sites for periods of 12 and 24 months confirm previous findings. ...

International Nuclear Information System (INIS)

In equipment industries, the equipments handling industrial water and pure water are numerous. In power generation including nuclear power generation, water serves as a working medium. Review is made on the experiences in the corrosion of iron and nickel base alloys in high temperature, high pressure water and the results of researches derived from them. Under high temperature and high pressure, carbon steel, low alloy steel, stainless steel and high nickel alloy cause corrosion even in pure water. But in the case of serious corrosion, chlorine, oxygen, alkali and others in water take part. The following matters are described: corrosion by steam; stress corrosion cracking in pure water; corrosion by impurities in high temperature, high pressure pure water, i.e. chlorine ions, dissolved oxygen, and alkali; corrosion under radiation. (J.P.N.).

Energy Technology Data Exchange (ETDEWEB)

Corrosion is said to be the most dominant factor which affects the physical life of ships and offshore structures. In order to secure the structural safety of ships and offshore structures, it is necessary to take measures to corrosion based on the prediction of condition of progressive corrosion. But such prediction is difficult because the behavior of corrosion`s progress is probabilistic. In this paper, probabilistic model, which could evaluate the degradation of coatings and the successive corrosion of steel members, was proposed in order to explain the tendency of the actual corrosion conditions of existing ships. Then, statistical inferences on the proposed model were made by applying the actual data on plate thickness measurements of Bulk Carriers` Cargo Hold. And validity of the proposed model was verified.

UK PubMed Central (United Kingdom)

Separate groups of rats received 500 trials of lever-press training under autoshaping (food delivery followed 10-second lever presentations, or occurred immediately following a response); operant conditioning...Full Text Available

UK PubMed Central (United Kingdom)

All ceramic fixed partial dentures (FPD)s exhibit enhanced biocompatibility and esthetics as compared to metal-ceramic restorations. However, framework fractures are frequently reported especially when...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this work, an attempt was made to develop a novel type of wear-resistant composite employing a TiNi alloy matrix reinforced by hard particles. Titanium carbide was chosen as the reinforcing phase because of its high hardness and TiNi alloy as the matrix due to its pseudoelasticity and good toughness. TiC particles may sustain external load, while the TiNi matrix may accommodate deformation, absorb impact energy and retain the hard particles. Such a combination is expected to lead to an enhanced wear resistance, compared to TiNi alloy. As a matter of fact, some efforts were previously made to develop TiNi-matrix composite reinforced by ceramic particles. However, the emphasis of those studies was put on effects of the reinforcing particles on the phase transformation behavior, shape memory effect and some mechanical properties of the composite; no attempt was made to explore the potential benefit of ...

UK PubMed Central (United Kingdom)

The regulation of gene expression in the brain reward regions is known to contribute to the pathogenesis and persistence of drug addiction. Increasing evidence suggests that the regulation of gene transcription...Full Text Available

UK PubMed Central (United Kingdom)

Muscarinic cholinergic receptors modulate dopaminergic function in brain pathways thought to mediate cocaine's abuse-related effects. Here, we sought to confirm and ...Full Text Available

UK PubMed Central (United Kingdom)

The current study examined the reinforcing effects of choosing among alternatives in a four-part evaluation. In the first study, initial-link responses in a concurrent-chains arrangement resulted in...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The corrosion behavior of 304 stainless steel was characterized with cyclic voltammetry in a eutectic Li/K and Li/Na carbonate melt under anode and cathode gas of the molten-carbonate fuel cell (MCFC). The corrosion rate of 304 steel was determined in four different environments of the MCFC with electrochemical methods and from cross-sectional analysis of corrosion layers. These four environments were open-circuit and MCFC-load conditions both under anode and cathode gas. At open-circuit conditions corrosion was more severe under the oxidizing cathode gas then under the reducing anode gas. On the contrary, at load conditions corrosion was more severe under anode than under cathode gas. The anodic polarization under anode gas enhances corrosion, whereas the high anodic polarization under cathode gas leads to anodic protection. Corrosion ...

International Nuclear Information System (INIS)

As the first step for development of the corrosion resistant superheater tube materials of 500 C, 100 ata used in high efficient waste-to-energy plants, field corrosion tests of six conventional alloys were carried out at metal temperatures of 450 C and 550 C for 700 and 3,000 hours in four typical Japanese waste incineration plants. The test results indicate that austenitic alloys containing approximately 80 wt% [Cr+Ni] show excellent corrosion resistance. When the corrosive environment is severe, intergranular corrosion of 40#approx#200 microm depth occurs in stainless steel and high alloyed materials. It is confirmed quantitatively that corrosion behavior is influenced by environmental corrosion factors such as Cl concentration and thickness of deposits on tube surface, metal temperature, and flue gas temperature. The excellent ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion probes are being developed and combined with an existing measurement technology to provide a tool for assessing the extent of corrosion of metallic materials on the fireside in coal-fired boilers. The successful development of this technology will provide power plant operators the ability to (1) accurately monitor metal loss in critical regions of the boiler, such as waterwalls, superheaters, and reheaters; and (2) use corrosion rates as process variables. In the former, corrosion data could be used to schedule maintenance periods and in the later, processes can be altered to decrease corrosion rates. The research approach involves laboratory research in simulated environments that will lead to field tests of corrosion probes in coal-fired boilers. Laboratory research has already shown that electrochemically-measured corrosion ...

Energy Technology Data Exchange (ETDEWEB)

The e/sup -/..-->..e/sup -/(..nu..nu-bar) process in the field of a circularly polarized plane wave is studied in the framework of the Glashow-Weinberg-Salam model. General expressions for the probability of creation of neutrino pairs are obtained, and the case of a low-intensity wave is studied in detail. The effects of asymmetry of emission of electron and muon neutrinos are estimated, and comparison with previous results is performed.

Energy Technology Data Exchange (ETDEWEB)

We use a nonsingular-potential model for heavy quarkonia proposed by Gupta, Repko, and Suchyta to calculate the transition amplitudes for the magnetic-dipole ({ital M}1) one-photon radiative decays of the {ital c{bar c}} and {ital b{bar b}} bound systems. The wave functions of the bound systems are calculated by a nonperturbative treatment. The results are in better agreement with the experimental data than those predicted using other potential models.

CERN Document Server

After presenting three ways of defining a bulge component in disc galaxies, we introduce the various types of bulges, namely the classical bulges, the boxy/peanut bulges and the disc-like bulges. We then discuss three specific topics linked to bulge formation and evolution, namely the coupled time evolution of the bar, buckling and peanut strengths; the effect of velocity anisotropy on peanut formation; and bulge formation via bar destruction.

Energy Technology Data Exchange (ETDEWEB)

We develop the boundary string field theory approach to tachyon condensation on the D{bar D} system. Particular attention is paid to the gauge fields, which combine with the tachyons in a natural way. We derive the RR couplings of the system and express the result in terms of Quillen's superconnection. The result is related to an index theorem, and is thus shown to be exact.

CERN Document Server

We examine the observable properties of simulated barred galaxies including radial mass profiles, edge-on structure and kinematics, bar lengths and pattern speed evolution for detailed comparison to real systems. We have run several simulations in which bars are created through inherent instabilities in self-consistent simulations of a realistic disc+halo galaxy model with a disc-dominated, flat rotation curve. These simulations were run at high (N=20M particles) and low (N=500K) resolution to test numerical convergence. We determine the pattern speeds in simulations directly from the phase angle of the bar versus time and the Tremaine-Weinberg method. Fundamental dynamics do not change between the high and low resolution, suggesting that convergence has been reached in this case. We find the higher resolution is needed to simulate structural and kinematic properties accurately. The edge-on view of the ...

International Nuclear Information System (INIS)

We give a theoretical design for a locally resonant two-dimensional cylindrical structure involving a pair of C-shaped voids in an elastic medium which we term as double 'C' resonators (DCRs) and imbedded thin stiff bars, that displays the negative refraction effect in the low frequency regime. DCRs are responsible for a low frequency band gap which hybridizes with a tiny gap associated with the presence of the thin bars. Using an asymptotic analysis, typical working frequencies are given in closed form: DCRs behave as Helmholtz resonators modeled by masses connected to clamped walls by springs on either side, while thin bars behave as a periodic bi-atomic chain of masses connected by springs. The discrete models give an accurate description of the location and width of the stop band in the case of the DCR and the first two dispersion bands for the periodic thin bars. We then combine our asymptotic ...

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion is localized accelerated dissolution of metal that occurs as a result of a breakdown of the otherwise protective passive film on the metal surface. This paper provides an overview of the critical factors influencing the pitting corrosion of metals. The phenomenology of pitting corrosion is discussed, including the effects of alloy composition, environment, potential, and temperature. A summary is then given of studies that have focused on various stages of the pitting process, including breakdown of the passive film, metastable pitting, and pit growth. 120 refs.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

... Hayashi, Shinichiro Japan Atomic Energy Agency, Tokai, Ibaraki (Japan)

Science.gov (United States)

... THE STRENGTH, TOUGHNESS, AND STRESS-CORROSION CRACKING SUSCEPTIBILITY OF A METASTABLE BETA TITANIUM ALLOY (Ti-11. ...

International Nuclear Information System (INIS)

Corrosion resistance of Cu-W system condensates in tap water was studies. It is shown that with an increase in W concentration in the condensates of the Cu-W system their corrosion in tap water enhances. In the material designated for power supply facilities the optimal tungsten content is up to 6%. Owing to formation of oxide film on the surface of the samples corrosion is stabilitized 40 h after the test start.

Energy Technology Data Exchange (ETDEWEB)

A necessary condition for crevice corrosion is that a crevice former create a sufficiently tight, restricted geometry on the metal surface to support the development of critical crevice chemistry. Crevice corrosion is affected by the crevice geometry (tightness) and the properties of the crevice former. The objective of this study is to determine the effect of the crevice former material on the evolution of localized corrosion-damage. A standard crevice corrosion test method is modified by (a) the use of ceramic, metal or polymer materials as the crevice former and (b) the variation of size and shape of the crevice. This study focuses on the post initiation stage of crevice corrosion and addresses factors that may limit the initiation of localized corrosion and also slow or stop the continued propagation of corrosion. Controlled crevice ...

International Nuclear Information System (INIS)

Zirconium is a transition element located along with sister elements titanium and hafnium in Group IVB of the periodic table. It is grayish white metal, with a density somewhat less than carbon steel. Zirconium is the ninth most common metallic element in the earth's crust, and is more abundant than zinc, lead, nickel, or even copper. Zirconium is exceptionally resistant to corrosion by many common acids and alkalis. It is resistant to most organic acids, such as formic, acetic, lactic, and oxalic acids. It also has a high resistance to localized forms of corrosion, such as pitting, crevice corrosion, and stress corrosion cracking. Its corrosion resistance is caused by the formation of a dense, tenaciously adherent, chemically inert oxide film on the surface. This oxide film protects the base metal from both chemical and mechanical attack at temperatures up to about 400 C (750 F). ...

International Nuclear Information System (INIS)

Corrosion of steam generator heat transfer tubes (SGHTT) is one of the important problems which affect safety operation of nuclear power plants (NPP), and the hazard of pitting corrosion of heat transfer tubes is the most serious. With an acoustic emission device, the signals during a corrosion test on SGHTT were collected and analyzed, and the corrosion points in the tubes were located accurately. The results show that pitting corrosion of heat transfer tubes has passed through three periods in its development: expansion phase, stationary phase and rapid developing phase. The corrosion damage of HTT can be found earlier with acoustic emission than any other non-destructive testing methods. Acoustic emission can be used for on-line and real-time monitoring of the safety and operation of the steam generator and has therefore a great significance. (orig.)

International Nuclear Information System (INIS)

The effect of alloying low carbon 18Cr-30Ni steel with silicon (up to 5.1%), copper (up to 5.4%), cobalt (up to 15.3%) on the resistance to corrosion cracking and pitting corrosion, is studied. Tests on uniaxial tension are carried out in 42% MgCl_2 solution and gravimetric studies in 10% FeCl_3x6H_2O. It is established that alloying steel of the Kh18N30 type with silicon increases strength and resistance to corrosion cracking. Copper and cobalt decrease a resistance to pitting corrosion but somewhat increase a resistance to corrosion cracking.

Energy Technology Data Exchange (ETDEWEB)

Due to the well-establish corrosion problems of Alloy 600 as a steam-generator material and the subsequent focus on thermally treated (TT) Alloy 690 and Alloy 800 as alternative materials, a systematic analysis of the corrosion behavior of these two latter alloys is warranted. Corrosion test results for Alloys 690 TT and 800 were collected and organized in the form of corrosion mode diagrams. Selected data for mill annealed (MA) Alloy 600 were also included for reference. The corrosion mode diagrams correlate the modes of corrosion degradation observed in tests as functions of the environment pH and electrochemical potential (ECP). The diagrams confirm that Alloys 690TT shows some susceptibility in caustic environments, and Alloy 800 shows susceptibility in both caustic and highly acidic environments. (authors). 6 figs., 5 refs.

International Nuclear Information System (INIS)

The possible corrosion damage is discussed of the CrNi and CrNiMo types steels used as structural materials in WWER type nuclear power plants. It includes point and slot corrosion, corrosion cracking and corrosion fatigue as well as corrosion denting. Also discussed are test procedures that simulate operating conditions and are used for assessing the properties of metallurgical products (sheets and tubes) used in nuclear power engineering. Briefly described is a system for testing the said products in an aqueous medium while keeping the test parameters in a narrow range for a long time. Under the defined temperature, pressure and corrosion medium composition, the test specimens in this system can mechanically be loaded, both statically and dynamically or a temperature gradient can be produced at the tube-tube plate joint. (Z.M.). 1 fig., 1 tab., 10 refs.

Energy Technology Data Exchange (ETDEWEB)

The ability to monitor the corrosion degradation of key components in fossil fuel power plants is of utmost importance for Futuregen and ultra-supercritical power plants. Fireside corrosion occurs in the high temperature sections of energy production facilities due to a number of factors: ash deposition, coal composition, thermal gradients, and low NOx conditions, among others. Problems occur when equipment designed for either oxidizing or reducing conditions is exposed to alternating oxidizing and reducing conditions. This can happen especially near the burners. The use of low NOx burners is becoming more commonplace and can produce reducing environments that accelerate corrosion. One method of addressing corrosion of these surfaces is the use of corrosion probes to monitor when process changes cause corrosive conditions. In such a case, ...

International Nuclear Information System (INIS)

Previous corrosion studies identified the materials Hastelloy C4, Ti 99.8-Pd, and carbon steels as promising for the manufacture of long-lived high-level waste containers that could act as an engineered barrier in a rock-salt repository. Here, the efficiency of the corrosion-resistant concept using surface-welded Hastelloy C4 as corrosion protection of carbon steel containers is compared with the corrosion-allowance concept using unalloyed or low-alloyed steels. The materials are examined in three disposal relevant brines (two rich in MgCl_2, one rich in NaCl) at 150 C. The results indicate that welded Hastelloy C4 is highly resistant to corrosion in the NaCl-rich brine. In the presence of sulfides or MgCl_2-rich brines, however, severe pitting corrosion occurs. The three steels investigated are resistant to pitting corrosion in all brines, ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this text is to train engineers and technologists not just to understand corrosion but to control it. Materials selection, coatings, chemical inhibitors, cathodic and anodic protection, and equipment design are covered in separate chapters. High-temperature oxidation is discussed in the final two chapters ne on oxidation theory and one on controlling oxidation by alloying and with coatings. This book treats corrosion and high-temperature oxidation separately. Corrosion is divided into three groups: (1) chemical dissolution including uniform attack, (2) electrochemical corrosion from either metallurgical or environmental cells, and (3) stress-assisted corrosion. Corrosion is logically grouped according to mechanisms rather than arbitrarily separated into different types of corrosion as if they were unrelated. For those ...

Energy Technology Data Exchange (ETDEWEB)

Severe pitting corrosion occurred in a horizontal steel pipeline used to transport multiphase fluid, including water, oil, and natural gas, after 2 months of service. The pitting corrosion rate was up to 42 mm/year. Chemical analysis, X-ray diffractometry, and EDAX showed that the corrosion products mainly consisted of Fe9S8, FeCO3, and NaCl. Calcium containing inclusions were also found in the matrix of the steel, which may accelerate corrosion. The early failure was attributed to the high proportion of water, the slow flow velocity, and the use of unqualified material. (Author)

International Nuclear Information System (INIS)

The mechanism of the salt concentration increase in pits and crevices formed in a steam generator due to its imperfect manufacture or to its design features is described. The probability of corrosion can be reduced by choosing a suitable steel and by securing low concentrations of salts (chlorides in particular) and corrosion products in the feedwater. Attention is paid to the distribution of salts in the water-steam circuit and to the conditions of erosion corrosion as the principal source of corrosion products in feedwater. Experience with the suppression of erosion corrosion at nuclear power plants abroad is described. (E.J.).

International Nuclear Information System (INIS)

SiSiC is one of selected materials for the thermal chemical hydrogen production IS (Iodine-Sulfur) process at JAERI. SiSiC was tested in boiling sulfuric acid for 1000 hours. The obtained results showed the following facts. The transverse strength was not changed by sulfuric corrosion, high temperature oxidation and oxidation. Silica scale formed on SiSiC by sulfate corrosion and high temperature oxidation had corrosion resistance in boiling sulfuric acid. Bilayer structure of silica scale produced by high temperature oxidation was not affected by sulfate corrosion. (S.Y.).

Energy Technology Data Exchange (ETDEWEB)

We study CP-violating phenomena in the production, mixing and decay of a coupled system of CP-violating neutral Higgs bosons at {gamma}{gamma} colliders, assuming a Minimal Supersymmetric Standard Model (MSSM) Higgs sector in which CP violation is radiatively induced by phases in the soft supersymmetry-breaking gaugino masses and third-generation trilinear squark couplings. We discuss CP asymmetries in the production and decays of {mu}{sup +}{mu}{sup -}, {tau}{sup +}{tau}{sup -}, b-bar b and t-bar t pairs. We find large asymmetries when two (or all three) neutral Higgs bosons are nearly degenerate with mass differences comparable to their decay widths, as happens naturally in the CP-violating MSSM for values of tan{beta}-bar 5 (30) and large (small) charged Higgs-boson masses.

Energy Technology Data Exchange (ETDEWEB)

I present an overview of the measurement of the proton form factors in the time-like regiun. BABAR has recently measured with great accuracy the e{sup +} e{sup -} {yields} p p-bar reaction from productiun threshold up to an energy of {approx} 4.5 GeV; finding evidence for a ratio of the electric to magnetic form factur greater than unity, contrary to expectation. In agreement with previous measurements. BABAR confirmed the steep rise uf the magnetic form factor close to the p p-bar mass threshold, suggesting the possible presence of an under-threshuld N N-bar vector state. These and uther open questiuns related to the nucleon furm factors both in the time-like and space-like region, wait for more data with different experimental techniques to be possibly solved.

Energy Technology Data Exchange (ETDEWEB)

At the LEAR facility, CERN, antiprotonic L{alpha} transitions in light elements have been investigated with a focussing crystal spectrometer. The high resolution of the experiment allowed for the first time to resolve in p-barH the 2{sup 3}P{sub 0} state from the close lying states 2{sup 3}P{sub 2}, 2{sup 1}P{sub 1}, and 2{sup 3}P{sub 1}. In p-barD the corresponding transitions were found to be more than an order of magnitude broader. To a large extent the results for p-barH support the meson exchange model.

Energy Technology Data Exchange (ETDEWEB)

Direct Flame Impingement involves the use of an array of very high-velocity flame jets impinging on a work piece to rapidly heat the work piece. The predominant mode of heat transfer is convection. Because of the locally high rate of heat transfer at the surface of the work piece, the refractory walls and exhaust gases of a DFI furnace are significantly cooler than in conventional radiant heating furnaces, resulting in high thermal efficiency and low NOx emissions. A DFI furnace is composed of a successive arrangement of heating modules through or by which the work piece is conveyed, and can be configured for square, round, flat, and curved metal shapes (e.g., billets, tubes, flat bars, and coiled bars) in single- or multi-stranded applications.

Energy Technology Data Exchange (ETDEWEB)

Corrosion is a primary determinant of waste package performance at the proposed Yucca Mountain Repository and will control the delay time for radionuclide transport from the waste package. Corrosion is the most probable and most likely degradation process that will determine when packages will be penetrated and the shape, size, and distribution of those penetrations. The general issues in corrosion science, materials science and electrochemistry are well defined, and the knowledge base is substantial for understanding corrosion processes. In this paper, the Yucca Mountain Repository is viewed from a corrosion perspective. A major component of the long-term strategy for safe disposal of nuclear waste at the Yucca Mountain Repository is first to completely isolate the radionuclides in the waste packages for long times and to greatly retard the egress and transport of radionuclides ...

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion measuring method for almunum alloys sold on the market was studied. By addition of a little quantity of Cu {sup ++} ion, corrosion potential of alminum alloys rapidly approachs to pitting corrosion potential in the solution including chloride. After Cu {sup ++} ion of 5ppm is added in advance into the solution including chrolide to measure the pitting corrosion potential, alminum alloy test pieces are imersed into the solution in the atmospheric air, then the stable corrosion potential is shown after three-minite imersion, and this potential is defined to the pitting corrosion potential. The pitting corrosion potential can be easily measured by this method stated above (copper ion method). The values measured by copper ion method is comparatively agreed with that measured by the existing potentio dynamic method. The pitting ...

International Nuclear Information System (INIS)

Power plant components exposed to environments such as water and soil are susceptible to severe corrosion. Many times the effect of corrosion in power plant components can be catastrophic. The problem is aggravated for underground pipelines due to additional factors such as large network of pipelines, proximity to earth mat, high voltage transmission lines, corrosive chemicals, inadequate approach etc. Other components such as condenser water boxes, internals of pipelines, clarifier bridge structures, cooling water inlet gates and pipes etc. which are in continuous contact with water, are subjected to severe corrosion. The nature and locations of all such components are at places which are not accessible for routine maintenance and hence they require long term reliable protection against corrosion. Experience has shown that anti-corrosive coatings are inadequate ...

Energy Technology Data Exchange (ETDEWEB)

Because of the chaotic nature of the corrosion process and the complexity of the electrochemical noise signals that are generated, there is no generally accepted method of measuring and interpreting these signals that allows the consistent detection and identification of sustained localized pitting (SLP) as compared to general corrosion. We have reexamined electrochemical noise analysis (ENA) of localized corrosion using different hardware, signal collection, and signal processing designs than those used in conventional ENA techniques. The new data acquisition system was designed to identify and monitor the progress of SLP by analyzing the power spectral density (PSD) of the trend of the corrosion current noise level (CNL) and potential noise level (PNL). Each CNL and PNL data point was calculated from the root-mean- square value of the ac components of current and potential fluctuation signals, which ...

Energy Technology Data Exchange (ETDEWEB)

The friction and wear properties of glass fiber reinforced composites of nylons (nylon 6, nylon 66 and nylon 46) with different crystallinities due to their molecular structures were investigated by sliding them with alumina ceramics and using a pin-on-disk friction machine. The friction coefficients of the glass fiber reinforced nylons in oil were lower and more stable than those in air from the initial stage of friction. The transfer of nylon matrix to adhere onto the alumina surface in air was so much greater than in oil that the alumina surface could not be recognized. Consequently, a different between the friction and wear properties in air and in oil was resulted. Reinforcement of nylons with glass fiber remarkably improved their friction properties in oil by its lubricating action, while the wears were rather high contrary to what was expected. This tendency was conspicuous for nylon 46 with high crystallinity. ...

International Nuclear Information System (INIS)

Corrosion is a materials degradation process that engineering personnel in the pulp and paper industry have had to accept as unavoidable to some degree, due to aggressive processing conditions prevalent in paper mills. The increasing incidence of corrosion-related failures in plant and equipment has resulted in the introduction of new techniques to monitor corrosion rates, since many of the more traditional methods do not provide data that is either recent or accurate enough. Thin layer activation (TLA) is a new corrosion monitoring technique which has recently been employed to measure corrosion trends inside a continuous pulp digester. With TLA a surface is irradiated by a particle beam from a nuclear accelerator, causing it to be labelled with an accurate depth profile and low level radioactivity. By monitoring this activity, it is possible to calculate how much of the surface has ...

Wastenet

...ISO - ISO Standards - TC 156 - Corrosion of metals and alloys go to main navigation go to content area go to search International Standards for Business,...ISO Members FAQs Fr ISO Store Products ISO Standards By TC TC 156 Corrosion of metals and alloys ISO Store ISO Standards By ICS By ...aerospace standards Publications and e-products ISO Concept Database (ISO/CDB) Copyright TC 156 - Corrosion of metals and alloys Items to be displayed: Published ...responsibility of TC 156 Secretariat Standard and/or project Stage ICS 3ISO/WD 7441 Corrosion of metals and alloys Determination of bimetallic corrosion in outdoor ...

International Nuclear Information System (INIS)

Exposure tests of candidate materials were carried out up to 1000 hr in the sulfuric acid environments of thermochemical hydrogen production IS process, focusing on the corrosion of welded portion and of crevice area. In the gas phase sulfuric acid decomposition condition at 850degC, welded samples of Alloy 800 and of Alloy 600 showed the same good corrosion resistance as the base materials. In the boiling condition of 95 wt% sulfuric acid solution, test sample of SiC showed the same good corrosion resistance. Also negligible corrosion was observed in crevice corrosion. (author)

International Nuclear Information System (INIS)

The corrosion behavior of the sputter-deposited amorphous or nanocrystalline W-Nb alloys is studied in 10% NaCl, 0.1 and 1 M NaOH solutions at 24 deg. C, open to air using immersion tests and electrochemical measurements. Niobium metal acts synergistically with tungsten in enhancing the corrosion resistance of the W-Nb alloys so as to show lower corrosion rates than the corrosion rates of the alloy-constituting elements in almost all examined solutions. Corrosion rates of W-Nb alloys are about more than one order of magnitude less than that of the sputter-deposited tungsten and even lower than that of sputter-deposited niobium. The stability of the anodic passive films formed on the W-Nb alloys increase with niobium content.

Energy Technology Data Exchange (ETDEWEB)

We present a measurement of the t{bar t} production cross section using events with one charged lepton and jets from p{bar p} collisions at a center-of-mass energy of 1.96TeV. In these events, heavy flavor quarks from top quark decay are identified with a secondary vertex tagging algorithm. From 162 pb{sup -1} of data collected by the Collider Detector at Fermilab, a total of 48 candidate events are selected, where 13.5 {+-} 1.8 events are expected from background contributions. We measure a t{bar t} production cross section of 5.6{sub -1.1}{sup _1.2}(stat.){sub -0.6}{sup +0.9}(syst.)pb.

CERN Document Server

Previous work has shown the Orion Bar to be an interface between ionized and molecular gas, viewed roughly edge on, which is excited by the light from the Trapezium cluster. Much of the emission from any star-forming region will originate from such interfaces, so the Bar serves as a foundation test of any emission model. Here we combine X-ray, optical, IR and radio data sets to derive emission spectra along the transition from H+ to H0 to H2 regions. We then reproduce the spectra of these layers with a simulation that simultaneously accounts for the detailed microphysics of the gas, the grains, and molecules, especially H2 and CO. The magnetic field, observed to be the dominant pressure in another region of the Orion Nebula, is treated as a free parameter, along with the density of cosmic rays. Our model successfully accounts for the optical, IR and radio observations across the Bar by including a significant magnetic ...

Energy Technology Data Exchange (ETDEWEB)

We successfully reproduce one of the French pipe whip experiments with the computer code WIPS. The WIPS results are in excellent agreement with the experimental data and the French computer code TEDEL. This justifies the use of its pipe element in conjunction with its U-bar element in a simplified method of impact analyses.

International Nuclear Information System (INIS)

The modular and periodic antenna structure in TCA is shown to produce an extremely pure spectrum of excited waves. This purity, together with precise measurements of the antenna loading in different parts of the spectrum, has allowed us to demonstrate that it is essential to include both toroidal coupling and the Hall effect (#omega#/#omega#/sub c//sub i/not =0) in order to explain our results. We show that toroidicity produces coupling from the directly excited Vertical BarmVertical Bar = 1 wave to Vertical BarmVertical Bar = 0,2 waves. Discrete Alfven Waves are also seen for Vertical BarmVertical Bar = 0,2 in addition to the directly driven Vertical BarmVertical Bar = 1. The importance of the Hall effect is most visible when a travelling wave is excited, in which case the antenna loading depends on the direction of the wave imposed. We present the antenna loading found with different excitation ...

Science.gov (United States)

Hour Fitness Center 24 Hour Market 24 Fitness Center Indoor Heated Pool with Whirlpool Seasonal Outdoor Pool Plaza w/ Outdoor Tiki Bar & Café 1,200 Square Foot Total of...

CERN Document Server

Non-axisymmetric forces are presented for 107 spiral galaxies using the 2 Micron All Sky Survey (2MASS) images. We apply both Cartesian integration and a polar grid integration utilizing a limited number of azimuthal Fourier components of density. We found that bar strength is independent of the method used to evaluate the gravitational potential. However, the polar method is more suitable for weak and noisy images. Bar strength was found to be sensitive to the Hubble-type dependent scale height of the disk, which has been ignored in the previous studies. On the other hand, the method is rather insensitive to the vertical model of the disk, as long as a same vertical dispersion is assumed, or to the boxy/peanut shaped structure, studied in terms of non-constant vertical scale height along the disk. In the near-IR most galaxies in our sample show non-axisymmetric forces in some level, and 40 percent of them have bars in a ...

Energy Technology Data Exchange (ETDEWEB)

The 220 kV Ch{bar u}si Trunk Line, now transmitting a maximum of 300 MW of electricity between the Ch{bar u}goku area of Honsh{bar u} and Shikoku island, is expected to be inadequate in the 1990's due to the rise in electrical demand. Therefore, to strengthen this interconnection, a new 500 kV transmission line was proposed. The most significant feature of this transmission line is the installation of 500 kV cables along the bridges (the Seto Ohashi Bridge) which span the Inland Sea (Seto). This is the first 500 kV long-distance transmission cable line. It is also the first large-scale cable line in the world installed along various types of bridges (ten bridges; route length of the bridge portion approximately 8 km). This paper gives an outline of the Honsh{bar u}---Shikoku interconnecting transmission line and also presents some technical features concerning 500 kV cables.

Science.gov (United States)

CuPt-type ordering in In{sub 0.49}Al{sub 0.51}P is studied by TEM. The lattice-matched film was grown by MOCVD on a GaAs substrate oriented 10{sup o} off (001) towards [110], at 650 C and 25 nm/min. TEM [110] and [1{bar 1}0] cross-sections (XS) were made by wedge polishing and 2 kV Ar ion milling. In CuPt-type ordering of In{sub 0.52}Ga{sub 0.48}P, alternating In-Ga-In-Ga {l_brace}111{r_brace} planes of group III atoms produce 1/2 {bar 1}11 and 1/2 1{bar 1}1 order spots in the 110 SADP, while the [1{bar 1}0] SADP shows no order spots [1-3]. A few studies have reported this type of order in In{sub 0.49}Al{sub 0.51}P [4]. The 004 BF image of the [1{bar 1}0] XS in Fig. 1 shows uneven light/dark contrast modulation due to phase separation often observed in In{sub 0.52}Ga{sub 0.48}P. There are also light/dark layers marked ML parallel to the film growth plane; such unintentional ...

International Nuclear Information System (INIS)

Considerations for longevity of nuclear facilities and ease of decommissioning are of great importance for future nuclear power plants. To this end, a concept of an optimal structural concept for nuclear reactor buildings has been studied: the main feature of this concept is to utilize large-sized, light weight prefabricated members with ultrahigh strength materials. The following two items have been selected to study the prospective structure: (1) Applicability of ultrahigh strength materials for reinforced concrete shear walls (2) Construction using large sized prefabricated members As the first step (1), material and structural tests using ultrahigh strength materials, and the subsequent analysis of those tests for reinforced concrete shear walls, has been conducted. The positive results of this study show a bright future for the use of ultrahigh strength materials for the reinforced concrete shear walls of nuclear ...

Energy Technology Data Exchange (ETDEWEB)

Quasi-carbon fibers (QCFs) were prepared from Polyacrylonitrile (PAN) precursor by pyrolysis in the temperature range from 400{degrees}C to 950{degrees}C. The QCF-reinforced composites were fabricated by impregnating the QCFs with the PAN resin. The microstructural changes of both QCFs and their composites were characterized by the X-ray diffraction method. The stacking size and the crystallinity of the QCFs increased with the increasing heat treatment temperature (HTT). The crystallinity of the PAN matrix in a composite was also affected by various QCFs. DSC data indicated that thermal reaction mechanism of the composite could be altered due to the interaction between the fiber and the matrix. DMTA studies showed that good adhesion existed at the interface of the QCF-reinforced composites containing lower HTT fibers. The modulus magnitudes of QCFs and their composites increased with the QCF pyrolysis temperature. Although the QCFs exhibited a ...

Energy Technology Data Exchange (ETDEWEB)

At future [gamma][gamma] colliders copious production of [ital t] [bar t] pairs is possible. This would allow for a detailed investigation of the interactions involving the top quark. We propose some correlations which are sensitive to [ital t] [bar t] final state interactions and we compute the QCD and standard model Higgs boson contributions to these correlations. A correlation resulting from the QCD induced transverse polarization of top quarks is found to be sizable and measurable at a high energy [ital e][sup +][ital e][sup [minus

International Nuclear Information System (INIS)

At future #gamma##gamma# colliders copious production of t bar t pairs is possible. This would allow for a detailed investigation of the interactions involving the top quark. We propose some correlations which are sensitive to t bar t final state interactions and we compute the QCD and standard model Higgs boson contributions to these correlations. A correlation resulting from the QCD induced transverse polarization of top quarks is found to be sizable and measurable at a high energy e"+e"- collider, which is operated as a photon collider through backscattering of laser photons, at an integrated luminosity of 10 fb"-"1.

Energy Technology Data Exchange (ETDEWEB)

We evaluate the sphere level S-matrix element of two tachyons and two massless NS states, the S-matrix element of four tachyons, and the S-matrix element of two tachyons and two Ramond-Ramond vertex operators, in type 0 theory. We then find an expansion for theses amplitudes that their leading order terms correspond to a covariant tachyon action. To the order considered, there are no T4, T2(-bar T)2, T2H2, nor T2R tachyon couplings, whereas, the tachyon couplings FF-bar T and T2F2 are non-zero.

International Nuclear Information System (INIS)

We study heavy physics effects on the Higgs production in #gamma##gamma# fusion using the effective Lagrangian approach. We find that the effects coming from new physics may enhance the standard model predictions for the number of events expected in the final states bar bb, WW, and ZZ up to one order of magnitude, whereas the corresponding number of events for the final state bar tt may be enhanced up to two orders of magnitude. copyright 1996 American Institute of Physics.

CERN Document Server

Attention is paid to the production mechanisms of light scalars that reveal their nature. We reveal the chiral shielding of the \\sigma(600) meson. We show that the kaon loop mechanism of the \\phi radiative decays, ratified by experiment, points to the four-quark nature of light scalars. We show also that the light scalars are produced in the two photon collisions via four-quark transitions in contrast to the classic P wave tensor q\\bar q mesons that are produced via two-quark transitions $\\gamma\\gamma\\to q\\bar q$. The history of spontaneous breaking of symmetry in quantum physics is discussed in Appendix.

International Nuclear Information System (INIS)

This paper analyzes fission neutron multiplicity for the /sup 242m/Am(n,f) reaction. The fission neutron multiplicity, v bar, of /sup 242m/Am(n,f) was measured relative to that of /sup 235/U(n,f) using the neutron time-of-flight facility at the Lawrence Livermore National Laboratory 100-MeV electron Linac. A comparison of the measured energy dependence of v-bar is made with semi-empirical models of neutron emission from the actinides. 22 refs.

International Nuclear Information System (INIS)

Most general tbW couplings were investigated in the process #gamma##gamma# #-># tt-bar #-># l"#+-#X for unpolarized photon beams. The double angular and energy distribution of the lepton was calculated and an optimal-observable analysis on it was carried out for the SM tt-bar production mechanism. It was also shown that the leptonic angular distribution is insensitive to non-standard tbW vertex. That means that observation of non-standard effects indicates existence of some new physics in the production part.

International Nuclear Information System (INIS)

Phenolic resins have made a major breakthrough in the field of high technology in 80's. These are now active participants of "high tech' areas ranging from electronics, computers, communication, outer space, aerospace, advanced materials, bio materials and technology. A phenol - formaldehyde (1:1.5) resin having resin content of 70% synthesized in the laboratory has been applied for wood coating and reinforcing glass fiber. The weatherability and solvent resistance of these items have been studied and results discussed keeping in view the envisaged application for structural materials and chemical equipment. The toxic materials released during contact with solvents for chemical applications and during degradation general have been monitored. The results are discussed with reference to environmental pollution due to these resins and their composites under different conditions. (authors)

British Library Electronic Table of Contents (United Kingdom)

Silica-reinforced natural rubber (NR) composite was prepared by using tetraethoxysilane (TEOS) as a precursor to generate silica particles inside the rubber. The silica was generated in situ by the sol-gel process of TEOS that was mixed directly into commercial-graded NR latex having 60% dry rubber content and 0.7% ammonia. The conversions of TEOS to silica inside the rubber were ranging from 90 to 97%. The silica particles dispersed evenly without extensive aggregation with sizes between 100 and 500 nm, as determined by scanning electron microscopy (SEM). An experimental design methodology, namely "two-level factorial design," was used to evaluate the influence of the amounts of TEOS, ammonia, and gelation time on the tensile modulus, tensile strength, and tear strength of the vulcanizate...

British Library Electronic Table of Contents (United Kingdom)

The paper discusses the aspects of repair and retrofitting technique adopted for a damaged reinforced concrete beam-column joint specimen under cyclic loading. A specimen designed based on Indian Standard specifications with consideration of seismic load but without adopting ductile detailing (NonDuctile) was investigated under reverse cyclic loading. Then, the damaged nonductile specimen was repaired with epoxy mortar and grouted using low viscous polymer, and retrofitted using fiber reinforced plastic (FRP) wrapping in beam and column components and steel plate jacketing in joint region. The experimental results showed that the retrofitted specimen not only regained its original strength and stiffness but also has overcome the deficiencies of nonductile detailing. The present study shows...

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of single-fiber pullout tests for deformed and smooth steel fibers embedded in the newly developed very-high strength concrete (VHSC) matrixes. The pullout test program involved four types of steel fibers, eight compressive strengths of VHSC matrixes, and two normal concrete strengths. Test results have shown that pullout behavior of different steel fiber reinforced VHSC composites is influenced by the matrix strength and fiber end condition (smooth, flat end, or hooked). Results reveal that both maximum pull-out load and total pullout energy increases as matrix strength increases for all deformed fibers that did not rupture. The test results also indicated that the increase in total pullout energy is more significant than that in peak load.

British Library Electronic Table of Contents (United Kingdom)

This current work is concerned with the development of polypropylene composites reinforced with cellulose and cellulignin fibers attained from sugarcane bagasse. Moreover, the fibers were chemically modified by acetylating process and its effects on the fiber/matrix interaction were also evaluated. The chemical modification efficiency was verified by FTIR analysis and the fibers morphological aspects of fibers by SEM. Likewise, the influence of modified fibers content in the composites was studied by mechanical (tensile, shear and flexural tests) and thermal analyses (TGA and DSC). After the chemical modification, the FTIR results showed the appearance of acetyl groups and reduction of OH bonds for all fibers. Together with, SEM characterization showed that the acetylation changed the morp...

Science.gov (United States)

The corrosion behavior of Ta, Ti, and Zr in inorganic acids, bases, chlorides and miscellaneous salts, waters and gases, and organic acids and miscellaneous organic chemicals is summarized. (W.L.H)

Energy Technology Data Exchange (ETDEWEB)

The effect of dissolved oxygen and copper on denting corrosion at 280/sup 0/C in solutions of NaCl at pH 9 with ammonia was investigated using a packed tube/support plate crevice in a laboratory simulation. The onset of corrosion was detected with a hydrogen analyzer sensitive to 0.2 ppB. In the absence of copper, rapidly rising hydrogen concentrations were detected only when the product of the chloride and oxygen concentrations were detected only when the product of the chloride and oxygen concentrations in the boiler-water exceeded 25 (ppM)/sup 2/, but at these high concentrations, unheated low-carbon steel surfaces in the system were as sensitive to corrosion as the heated crevice. When copper metal was present in the feed system, corrosion of the heated crevice occurred in the absence of oxygen, provided the copper had previously been exposed to dissolved oxygen. Dosing hydrazine into the feedwater ...

International Nuclear Information System (INIS)

The following conclusions are drawn from the study of the effects of dissolved oxygen on corrosion denting: 1) Following the ingress of fresh-water contamination into a PWR boiler, an acidic chloride solution can be formed in the crevice between tube and tube support plate when an oxidant such as dissolved oxygen or copper ions is present in the boiler water. 2) In the absence of copper, very high levels of dissolved oxygen and neutral chloride are necessary to initiate corrosion. 3) When copper is present in the feed system, sufficient copper ions to initiate corrosion within the crevice are released when the chloride concentration is 0.8 mg/kg and probably also at lower chloride values. Corrosion initiation however may require prior exposure of the copper to dissolved oxygen and can be suppressed by pretreatment with hydrazine. 4) The effect of dissolved oxygen on corrosion ...

Energy Technology Data Exchange (ETDEWEB)

The susceptibility to pitting corrosion of AA2024-T4, AA7075-T651 and AA7475-T761 aluminium alloys was investigated in aqueous neutral chloride solution for the purpose of comparison using electrochemical noise measurement. The experimentally measured electrochemical noises were analysed based upon the combined stochastic theory and shot-noise theory using the Weibull distribution function. From the occurrence of two linear regions on one Weibull probability plot, it was suggested that there existed two stochastic processes of uniform corrosion and pitting corrosion; pitting corrosion was distinguished from uniform corrosion in terms of the frequency of events in the stochastic analysis. Accordingly, the present analysis method allowed us to investigate pitting corrosion independently. The susceptibility to pitting corrosion was ...

International Nuclear Information System (INIS)

Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to considerable investigation of the mechanism of corrosion and for palliatives. The basic mechanism is now fairly well understood. Chloride present in the boiler feedwater from condenser leakage is concentrated in the support plate crevice as a result of the superheat present. This leads to the formation of a low pH acid ferrous chloride environment either through the hydrolysis of a weak base chloride such as MgCl_2 or the combined action of a neutral chloride with an oxidizing agent. Rapid attack of the carbon steel ensues with the Fe_3O_4 corrosion product forming at the metal/oxide interface. This oxide has a volume approximately twice that of the steel consumed and thus eventually fills the crevice between the tube and the support plate. Oxide growth continues leading to compression of the ...

Energy Technology Data Exchange (ETDEWEB)

Electrochemical corrosion rate probes were constructed and tested along with mass loss coupons in a N2/O2/CO2 plus water vapor environment. Temperatures ranged from 450 to 600 C. Corrosion rates for ash-covered mild steel, 304L SS, and 316L SS probes using electrochemical techniques were a function of time, temperature, and process environment. Correlation between electrochemical and mass loss corrosion rates was good.

International Nuclear Information System (INIS)

... Development Center, National Tsing-Hua University, Hsinchu, TW (China)

International Nuclear Information System (INIS)

A study of stress corrosion cracking susceptibility of Zircaloy-4 in chloride-containing aqueous methanolic media is presented. The influence of water content is investigated in the 5-100 vol. % water range. The dependence of stress corrosion cracking on potential is evidenced. A close correlation is established with pitting susceptibility determined by a statistical analysis of induction times. A correlation with the repassivation potential is observed in the water-rich solutions. In the low water content solutions, two repassivation curves are determined according to the experimental technique. Pit morphology and fractography show a transition from aqueous to organic media. (author).

International Nuclear Information System (INIS)

Some examples are given of design adaptations, e.g. U-bend support, tube spacer grid, flow distribution baffle, triangular tube pitch, tube-tubeplate sheet connection, which reduce the tendency to various types of corrosion (stress corrosion cracking, tube denting, tube wastage, intergranular cracking). A basic diagram of the secondary circuit is shown. Oxygen, corrosion product and impurity control in the secondary circuit is described. (E.J.). 19 figs., 6 refs.

Science.gov (United States)

... Title : RESULTS ON INCOLOY 800 AND ALLIED STEAM GENERATOR MATERIALS IN FLORIDA FIELD CORROSION TESTS,. ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Eight years ago, corrosion and tube denting seriously threatened the reliability and design life of steam generators, especially for closed loop arrangements in pressurized water reactors (PWRs). Concentrated research by the Steam Generator Owners Group (SGOG) diagnosed the causes and produced effective solutions, notably guidelines for water chemistry control in the secondary loop. The guidelines recommend specific levels of water impurities and remedial actions to prevent cooling-water leaks in the condenser, prevent air leaks, limit corrosion product buildup, and remove some impurities while neutralizing others. Continued research in SGOB-II is investigating intergranular corrosion and stress corrosion cracking. 3 figures.

International Nuclear Information System (INIS)

German 1978. p. 817-820. Germany Wieling, N. Stieding, L. Kraftwerk

International Nuclear Information System (INIS)

... Industry, Material Science Research Laboratory, Yokosuka, Kanagawa (Japan)

International Nuclear Information System (INIS)

... Yoshiaki Toshiba Corp., Nuclear Power Division, Yokohama, Kanagawa (Japan)

International Nuclear Information System (INIS)

... aluminum calcium calcium 45 cations citric acid corrosion inhibition radiation

International Nuclear Information System (INIS)

... Japan) Kobayashi, Minoru AITEL Corp., Yokohama, Kanagawa (Japan)

International Nuclear Information System (INIS)

The importance that must be attached to the phenomenon of stress corrosion cracking of austenitic alloys is emphasized. The relation between chemical composition of various alloys and their sensitivity to cracking is shown with particular reference to the behaviour of Alloy 800. The different effects of alkaline anc chloride environments are discussed. Studies are reported of the general corrosion of Alloy 800 and other alloys in an environment representative of the primary coolant of PWR reactors; and of the behaviour of various alloys (including Alloy 800) in the conditions envisaged for their use for steam generators with superheat up to about 550 deg.C. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion can be considered as a combination of two physical processes: the pit generation process and its depth growth process. Both processes are uncertain and can be modeled by stochastic processes. A model that combines two stochastic processes to describe pitting corrosion was developed. In this model, the pit generation process is represented by the Poisson process, and the pit depth growth process is modeled by the Markov process. The probability distribution of corrosion pit depth and the probability of time-to-failure are derived based upon the combined stochastic processes. Examples of the use of this method in dealing with experimental data also were developed.

Energy Technology Data Exchange (ETDEWEB)

Localized corrosion has a stochastic character by nature. This character leads to an observed random behavior: fluctuations of the free potential, fluctuations of the current when a constant potential is maintained. This random signal, which is similar to an electric noise, can be analyzed either in the time domain by counting the events or in the frequency domain by measuring the power spectral density of the electrochemical noise. The experimental techniques developed for investigating the localized corrosion on the probabilistic point of view, i.e., statistical counting and power spectral density measurements, are discussed. Then the experimental results reported in the literature are reviewed in order to see what kind of parameters are accessible and how they can be related to the localized corrosion processes.

International Nuclear Information System (INIS)

In order to prevent corrosion failures of machines and structures, it is desirable to know in advance when the corrosion damage will take place, and appropriate measures are needed to mitigate the damage. The corrosion predictions are needed both at development as well as operational stage of machines and structures. There are several forms of corrosion process through which varying degrees of damage can occur. Under certain conditions these corrosion processes at alone and in other set of conditions, several of these processes may occur simultaneously. For a certain type of machine elements and structures, such as gears, bearing, tubes, pipelines, containers, storage tanks etc., are particularly prone to pitting corrosion which is an insidious form of corrosion. The corrosion predictions are usually based on ...

Energy Technology Data Exchange (ETDEWEB)

It is demonstrated that normal pitting can occur during oxidizing conditions in the repository. It is also concluded that a new theory for pitting corrosion has to be developed, as the present theory is not in accordance with all practical and experimental observations. A special variant of pitting, based on the growth of sulfide whiskers, is suggested to occur during reducing conditions. However, such a mechanism needs to be demonstrated experimentally. A simple calculational model of canister corrosion was developed based on the results of this study. 69 refs, 3 figs.

International Nuclear Information System (INIS)

The rapid corrosion of carbon steels in high temperature, acid chloride solutions is shown to be rate limited by the anodic reaction, 3Fe + 4H_2O = Fe_3O_4 + 8H"+ + 8e"-, based on experiments which find that the corrosion rate in 0.1M NiCl_2 solution has an activation energy of 60 kJ/ mole and is unaffected by adding NaCl or by replacing NiCl_2 with PtCl_4. (author).

British Library Electronic Table of Contents (United Kingdom)

The review provides a general idea about the types of metallic alloys and the pure metals used as implant materials in dental and orthopedic surgery. Their corrosive behavior in both real solutions and various media that model human biological fluids is described. Based on the literature data, it is concluded that multicomponent alloys containing titanium, niobium, zirconium, tungsten, molybdenum, aluminum, and silicon are the most resistant to corrosion. Implants made of different types of stainless steel are preferred when manufacturing orthopedic devices for short-term use.

Energy Technology Data Exchange (ETDEWEB)

General corrosion behavior of ALLOY 800 in high temperature water was studied in relation to its surface film structure. The surface film formed in water was found to decrease the corrosion rate of ALLOY 800. This film is composed of Ni ferrite, and can be obtained by oxidation in air or steam. Based on these results, air or steam oxidation treatment to inhibit Ni and Co release of ALLOY 800 into high temperature water is proposed. (author).

Energy Technology Data Exchange (ETDEWEB)

Electrochemical cyclic potentiodynamic polarization (CPP) experiments were performed on several candidate high-performance waste package container materials to evaluate their susceptibility to localized corrosion in aqueous environments relevant to the potential underground high-level nuclear waste repository. This paper presents the results of this study showing the effects of chloride ion (Cl) concentrations, pH, temperature, and electrochemical potential scan rate on the pitting corrosion behavior of these materials.

Energy Technology Data Exchange (ETDEWEB)

Simulated atmospheric corrosion studies were performed to determine the corrosion protection provided by galvanized zinc coatings on depleted uranium, U-0.75 Ti alloy, and U-6 Nb alloys. The accelerated ASTM tests consisted of exposing the galvanized samples to aqueous and aqueous chloride environments. The test results showed that anodic protection was provided by the electronegative zinc coatings on uranium and uranium alloys. Treating zinc with chromate conversion coatings also provided more protection.

Energy Technology Data Exchange (ETDEWEB)

Electrodeposited Zn alloys with Fe group metals are known to be more resistant than pure Zn. However, the role of the corrosion products on the corrosion inhibition is not considered up to date. The aim of the present work was to examine the composition of corrosion products, which form on the Zn and Zn alloy surfaces under atmospheric corrosion conditions up to 3 year of exposure, trying to correlate it with the differences in their corrosion resistance. Zn corrosion products have been characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Corrosion film composition was determined to depend on the sample exposure she, as well on the coating type. During the initial exposure stages oxide film was found to be the principal reaction product (XPS data), which in marine station consists from hydroxide phase ...

International Nuclear Information System (INIS)

The involvement and relationship of carbon steel corrosion products in the tube denting phenomenon promoted an intensive research effort to: 1) understand, reproduce, and arrest the denting process, and 2) evaluate alternative tube support materials to provide additional corrosion resistance. The paper summarizes a corrosion testing program for the verification of type 405 stainless steel under acid or all volatile treatment conditions.

Energy Technology Data Exchange (ETDEWEB)

As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress ...

International Nuclear Information System (INIS)

The steam generator availability is one of the important problems encountered during the pressurized water nuclear plant operation. Various kinds of corrosion phenomena were observed in the past. These phenomena result from the concentration of impurities mainly in three locations in the steam generators: the tubesheet crevices, the tube support plate crevices, and the sludge pile. Corrections were made in the design and the materials used but a number of steam generators suffer or will suffer from corrosion processes inducing in many cases forcing their replacement. In order to prevent or to retard the corrosions several laboratories have performed experiments to reproduce and to study the corrosion processes. The first step of the degradation is the concentration of chemical species. A method using /sup 24/Na as a radioactive tracer was used to establish the concentration kinetics of caustic which was ...

British Library Electronic Table of Contents (United Kingdom)

The effect of sodium gluconate anion (SG) on the corrosion and scale inhibition of ordinary steel in simulated cooling water has been studied using weight loss, polarisation curves, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) techniques. SG was studied in concentration from 10-4M to 10-1M. Results obtained reveal that SG perform excellently as corrosion and scaling inhibitor for ordinary steel in simulated cooling water. An increase of SG concentration leads to the increase of the corrosion potential towards the positive direction. The inhibition efficiency was a low temperature dependence. The inhibitor mechanism was treated as an adsorption process according to Langmuir adsorption isotherm. The SEM/EDAX data show that was a corrosion and scale inhi...

Energy Technology Data Exchange (ETDEWEB)

Stainless steels can get pitting corrosion in halide containing solution, which make them a big risk in industrial production. Many investigations were made in the past in order to understand processes involved in pitting corrosion, pit initiation and pit growth. Results about the influence of alloying elements, their contents, the state of the structure, the condition of the surface, the content of chloride, the temperature, the pH-value, the velocity of flow and of the oxidizer on the chloride induced pitting corrosion of passive stainless steels are presented. Electrochemical measurements and the application of surface analytical methods (SEM, SAM, XPS) with high lateral resolution are carried out. A part of the samples received a diffusion annealing in order to obtain reproducible results. Pitting Resistance Equivalents (PRE) - Pitting Index - with different multipliers are given and discussed critical. An ...

British Library Electronic Table of Contents (United Kingdom)

Considering the status of knowledge on corrosion and corrosion protection and especially the need for long term compatibility data of structural materials in HLM a set of experiments to generate reliable long term data was defined and performed. The long term corrosion behaviour of the two structural materials foreseen in ADS, 316L and T91, was investigated in the design relevant temperature field, i.e. from 300 to 550degreeC. The operational window of the two steels in this temperature range was identified and all oxidation data were used to develop and validate the models of oxide scale growth in PbBi. A mechanistic model capable to predict the oxidation rate applying some experimentally fitted parameters has been developed. This model assumes parabolic oxidation and might be used for de...

International Nuclear Information System (INIS)

The present invention concerns a method of evaluating corrosion resistance of a zirconium alloy easily and in a short period of time. An anode polarization curve of the zirconium alloy is measured to obtain an anode polarization curve expressed by logarithm. The curve is converted to a potential-current density curve expressed by absolute values. The peak area in the curve of the converted potential-current density is indicated by numerical values. Further, the corrosion resistance of the zirconium alloy is evaluated based on the peak area converted into the numerical values as a reference. This method is based on the finding that the peak area has a close relation with nodular corrosion resistance, and the corrosion resistance can be judged with respect to a specific zircaloy-2. (T.M.).

International Nuclear Information System (INIS)

An Ultra-Low-Carbon 19% Cr-11% Ni Stainless Steels used in nuclear fuel reprocessing plants where highly corrosion resistance in nitric acid is required has been developed. This steel has optimized the chemistry composition to decrease inclusions and deformation-induced martensitic transformation. The formation of deformation-induced martensite has the potential danger of accelerating corrosion in nitric acid. In this paper, effects of cold reduction and martensitic transformation on corrosion resistance of Ultra-Low-Carbon Stainless Steels in nitric acid are discussed. The developed steel showed excellent corrosion resistance during long-term exposure to nitric acid. (author).

British Library Electronic Table of Contents (United Kingdom)

A study of the ordinary mild steel/cooling water interface, with and without inhibitor, was carried out using electrochemical impedance spectroscopy (EIS). EIS spectra in uninhibited medium reveal that a layer of corrosion and scale products is formed naturally and evolves with the immersion time. Monosaccharides derivatives were used as corrosion inhibitors. Most of them exhibit good behaviour against corrosion of ordinary steel in simulated water systems. Their inhibiting efficiency increases with concentration rise and depends on molecular structure especially -OH groups' position on two adjacent carbons and their number. In addition, the effect of MoO4^2^- on the corrosion inhibition in the presence of the best inhibitor was also studied by EIS. The addition of MoO4^2^- enhanced the in...