Energy Technology Data Exchange (ETDEWEB)

This paper describes the experimental results of long-life solid lubricated ball bearings tested under high-vacuum of 10 exp -4 Pa, high-temperature of 300 C, and high-speed (9000 rpm) conditions. For full ball-type bearings, the thin soft metals, either Ag or Pb, which were coated on the races and balls, appeared to have good torque properties. However, the durability of such bearings was less than 300 hours. The transfer films from the lamellar solid MoS2 and metal composite retainers improved the torque and wear properties. For ceramic, i.e., silicon nitride, balls used with steel rings, wear occurred on the inner rings. All ceramic bearings with composite retainers showed improved torque and wear properties. 18 refs.

Energy Technology Data Exchange (ETDEWEB)

The instrument ball bearings are the key components of movable components for various kinds of measuring and control instruments; they often operate in the environmental condition of high-speed and light preload. In general, the non metal, disposable oilimpregnated retainer material has been used for these kinds of high precision miniature bearing. The engineering practice shows that the common failure mode of them is the wear which appears under the condition of insufficient lubrication condition. As the results, the vibration and noise will be enlarged, so does the frictional torque, which makes the ball bearings to lose its original working accuracy. It is the lifetime test of bearings that can enable the designers and manufacturers to chose the material of the bearing properly, optimize the product structure, mend the manufacturing ...

Energy Technology Data Exchange (ETDEWEB)

A 308-size hybrid ball bearing, with ceramic balls and steel rings, was tested using a diester oil and gas turbine fuel as lubricants at several speeds and loads. Heat generation data from this test work was then correlated with the heat generation model from a widely used computer code. The ability of this hybrid split inner ring bearing design to endure thrust reversals, which are expected in many turbine applications, was demonstrated. Finally, the bearing was successfully endurance tested in JP-10 fuel for 25 hours at 7560 N axial load and 36,000 rpm. This work has successfully demonstrated the technology necessary to use fuel-lubricated hybrid bearings in limited-life gas turbine engine applications such as missiles, drones, and other unmanned air vehicles (UAVs). In addition, it has provided guidance for use in designing such ...

Energy Technology Data Exchange (ETDEWEB)

For years rock bit performance has been progressively improved by many innovative changes to the design of both the bit cutting structure and the bearing. The changes have offered increased footage per bit and reduced cost per foot of hole through longer bit life and/or faster penetration rate. Efforts to assist the industry in drilling deeper thru hard abrasive rocks such as cherts of West Texas, conglomerated of the Rockies and bromides of Oklahoma led to a major breakthrough in rock bit design - the development of the tungsten carbide cutting structure. When properly applied the bit far exceeded that of the non-sealed ball and roller bearing being used at the time. The bearing failure mode was one of severe race spalling and abrasive wear influenced by the drilling fluid entering the bearing.

Energy Technology Data Exchange (ETDEWEB)

Ceramic antifriction bearings were introduced in excellent characterics and application. In main shaft use bearings of the machine tool, to be heightened in efficiency and accuracy by the heightening in speed, centrifugal load to the outer ring is not negligible to shorten the bearing in life. Also ball bearings with a contact angle are easily corroded by a very strong revolution slide due to the gyromoment. The use of such light weight material as silicon nitride's can design the lengthening in life. Also the utilization of high rigidity can prevent the inner ring from expanding by centrifugal force and enable the machining to be with a high accuracy. Ceramic rolling element is excellent also in backing resistant property and effective on the oily film cut. With heat resistant property, it maintains hardness even at high ...

Energy Technology Data Exchange (ETDEWEB)

Aiming to realize ball bearings operable in a vacuum and under high temperature, silicon nitride (Si3N4) ceramic ball bearings were tested. The tested ball bearings were angular contact ball bearings composed of silicon nitride with sputtered molybdenum disulfide coating using a retainer of hot-pressed self-lubricating composite material. The time variation of the frictional torque was examined for the operations under the conditions at 500{degree}C in a vacuum at a rotational speed of 600 rpm and 50N thrust load for 5{times}10{sup 7}revolutions (1400 hours) and for 1.5{times}10{sup 8}revolutions (4200 hours). Excellent tribological performance was obtained. The ball bearings are lubricated with the molybdenum disulfide film at the initial stage of the operation and with a ...

Energy Technology Data Exchange (ETDEWEB)

The main purpose of solid or fluid lubricants in ball-bearings is to separate the balls and races from contacting each other in so-called asperity collisions. Steel to steel contacts lead to microwelds which roughen functional rolling-contacting surfaces and deteriorate the lubricant. By using balls with a ceramic TiC coating, two goals are achieved. First, there are fewer asperity collisions because of the extreme smoothness of the high precision polished TiC coated balls. Second, if collisions do occur, there is practically no microwelding taking place, leaving the surfaces and the lubricant in good condition. Examples are given where the bearing lifetime is increased up to 10 times if the steel balls are replaced by TiC-coated balls. (orig.).

Energy Technology Data Exchange (ETDEWEB)

In this effort, the nonlinear responses and stability of a spindle system supported by ball bearings are presented. The dynamics of this system is described by a set of second order differential equations with a nonlinear piecewise smooth force. The Floquet theory is applied to investigate the stability of the periodic solution. Due to the loss of contact between the raceways and balls in the ball bearing, the bending of the frequency response curves switch to the left at the weak resonance region, which is similar to the frequency response curves of a system with a soft spring. With the decrease of the bearing clearance, the bending of the frequency response curves switch to the right, which is similar to the frequency response curves of a system with a hard spring. Increase of the frequency ratio, the bending of frequency response curves transforms from left ...

Energy Technology Data Exchange (ETDEWEB)

Ceramic ball bearings of silicon nitride are used for hard disk drive (HDD) spindle motors, to increase seed, reliability and memory capacity of the HDDs. Silicon nitride ceramics have advantages of lightweight, high strength and hardness over the conventional steel for bearings, but is expensive. A new process of high cost performance has been developed for mass production of the small-size ceramic balls. The company plans to apply these bearings to higher devices, e.g., servers, for the time being, and to expand the applicable areas, e.g., common devices and other small-size motors. The ceramic bearings have been developed jointly with Koyo Seiko Co. Ltd. (translated by NEDO)

Energy Technology Data Exchange (ETDEWEB)

IMO Momentenlager GmbH of Gremsdorf near Nuremberg produces large rotary bearings for ENERCON wind power systems, preferably for the E-70 and E-82 generators. (orig.)

International Nuclear Information System (INIS)

Ball screw bearings are used for the fine control of Control Rod Drive Mechanism (CEDM) for the SMART-P. Because the friction coefficient of the ball screw bearings suddenly increases at the limit temperature of 120 .deg. C, the surrounding temperature of the ball screw bearings should be less than the limit temperature for the functional integrity of the CEDM. The CEDM coolers are installed at the lower portion of the ball screw bearings to maintain the bearings' temperature less than the limit. In order to check the CEDM cooler satisfy the temperature limit of ball screw bearing at the possible operational conditions, the cooling capacity of the CEDM coolers, which was determined at the stage of 'conceptual design', is evaluated using the Computational ...

Energy Technology Data Exchange (ETDEWEB)

During rolling contact fatigue of the inner rings of ball bearings three stages of material response can be distinguished, in terms of the volume that is plastically deformed upon overrolling. After a first stage of material strengthening during which a decrease occurs for the volume that is deformed plastically, an effectively stationary, second stage is entered which is eventually succeeded by a third stage exhibiting a pronounced increase of the volume that is deformed plastically upon overrolling, which leads to failure. It is suggested that carbon diffusion induced by local temperature peaks occurring at the moment of overrolling is the key mechanism leading to fatigue damage. The amount of decomposed retained austenite is a useful, practical parameter to assess fatigue life. It is shown that published ideas about the role of certain components of residual stress in enhancing fatigue life are not ...

Science.gov (United States)

... d Diameter of ro.'ling element of a cylindrical roller bearing ... L Life (B-10) of a cyl.ndrical roller bearing LACA Contact ratio ...

Energy Technology Data Exchange (ETDEWEB)

The scope of the present article is two-fold. Firstly, to conduct an experiment to provide the temperature-time history of the cooling of a hot ball bearing in quiescent ambient air. Secondly, to predict the temporal variation of the bearing under the hypothesis of natural convection, radiation or natural convection coexists with radiation for a non-vanishing total hemispherical emissivity of the surface of the bearing. Numerical solutions of the three governing nonlinear lumped heat equations were carried out with a Runge-Kutta-Fehlberg (RKF45) algorithm accounting for automatic step size control. The experimental data was obtained with chrome steel ball bearings of diameter 0.953 cm (7/16 in) heated in an electric oven to a pre-set temperature. The heated bearing was exposed later to ambient air at atmospheric temperature and pressure. ...

Energy Technology Data Exchange (ETDEWEB)

The title invention aims at a vibrations-free running of the flywheel to realize a high speed (18,000-20,000 revolutions per minute). The flywheel consists of a case which holds a central stator, a rotor and two ball-bearings. The ball-bearings have a first radial stiffness and are placed in between the rotor and an upper, respectively lower support bearer. The support bearers are supported on the stator with a second radial stiffness. The top and the bottom of the stator is connected to the case by means of a support with a third stiffness. 6 figs.

Energy Technology Data Exchange (ETDEWEB)

The thermal contact resistance between balls and inner and outer rings of thermally steady space-use deep groove ball bearings was studied experimentally to verify the validity of the previously proposed calculation method for the resistance. The 440C stainless steel single row bearing was used for measuring its steady state temperature distributions in a vacuum environment under axial, radial and combined load conditions. As a result, the experimental results of the resistance well agreed with calculated ones under each load condition resulting in the sufficient validity at nearly the same surface roughness. It was necessary to apply a static equivalent radial load to calculation under the combined load that a contact angle is larger than the angle of resultant force dependent on both load components. In experiments under only radial load, measurement of outer ring temperatures was necessary at some ...

Energy Technology Data Exchange (ETDEWEB)

This paper explains technologies for turbo chargers used in light cars. Light car engine turbo chargers have been given various improvements responding to needs of the market. Since ball bearings have less mechanical loss than sliding bearings, and enhances greatly the turbo efficiency, they are used in some high performance engines of light cars. While the conventional ball bearing has used high hardness bearing steel, the new standard cars started using ceramic ball. The currently used light car gasoline engines are divided into two kinds, serial three-cylinder type and serial four-cylinder type, either having merits and demerits. The new twin entry turbo developed by IHI arranges divided exhaust gas ports above and below to simplify the manifold shape, and realizes smooth flow by twisting the exhaust gas flow path inside the turbine ...

Energy Technology Data Exchange (ETDEWEB)

The pipelines is provided for gases, particluarly helium, at temperature of about 1000/sup 0/C (pressure about 40 bar) and is used as the connection be tween a gas cooled high temperature reactor and a heat load. The pipe consists of a temperature-resistant inner tube, which is composed of several pipe sections, which are supported on ball bearings, and a gas tight pressurised outer tube. There are supports and insulation between the two tubes. The sub-claims concern fixing of and bearings for the pipe sections. The description is very detailed and supplemented by drawings.

Wastenet

... One 20 litre and one 15 litre removable bins Quick and easy installation Slides in and out on ball bearing track W248 x D455 x H485mm In Stock Email a Friend Quantity : 㿝.95 inc VAT Segregated Bins Stacked Bins Built-In Bins Office Bins Can Crushers Bags and Liners Accessories ...

British Library Electronic Table of Contents (United Kingdom)

This study examined the life histories of a group of emerging scholars in the field of mathematics education who identify themselves as having a particular interest in and concern for issues of equity and diversity. Experiences of being the "other," "bearing witness" to "othering experiences," and "orienting experiences" in relation to issues of equity proved to be prominent themes in participants' life histories. These experiences were then linked to the positionality that these scholars now have in relation to their research in mathematics education.

Energy Technology Data Exchange (ETDEWEB)

A totally-enclosed, fan-cooled, rib-cooled type induction motor is adopted for an exhauster which is to be installed in a ventilation station for dust catcher in a tunnel. It has the highest capacity in Japan for the above purpose, and is provided with a cooling fan inside to recirculate cooled air, thereby improving cooling efficiency and reducing size and weight. Three-row combined angular ball bearings are used as the thrust bearings, and grease lubrication system is adopted to simplify the inspection/maintenance works. It is to be delivered to Japan Highway Public Corporation's Shizuoka Construction Bureau, Yaizu site office. Its electric specifications are 455 kW, 440 V, 890 A and 510 rpm, and its mechanical specifications are thrust load: 16 kN and impeller load: 7.2 kN. (translated by NEDO)

International Nuclear Information System (INIS)

A series of ball-on-disc wear and friction measurements were made for surfaces which have a chemical vapour deposition carbon silicon alloy layer on a carbon substrate (fine grain POCO graphite). Nitrogen ion irradiation was used to improve the wear resistance of the carbon alloy surface. For comparison, measurements were also taken for alumina against alumina. It was found that the lowest friction coefficient and lowest wear occurred for ion irradiated coated samples containing 4% Si in the alloy and that the performance was superior to that of alumina. ((orig.)).

Energy Technology Data Exchange (ETDEWEB)

This patent describes an automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves on the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first.

Wastenet

...Oster | Best sexual wellness info Best sexual wellness info Home Posts Tagged Oster Oster Professional 103 Stim-U-Lax Massager Reviews Made of 100% ball bearing construction Traditional frame design with special frame contour to fit hand and reduce hand fatigue Chrome housing and rubber hand pad Heavy-duty, single speed UL approved 120v This lightweight therapeutic massager combines the advantages of hand and mechanical massage. Its special contoured design reduces hand fatigue and its universal ...

Energy Technology Data Exchange (ETDEWEB)

A highly reliable control rod drive mechanism (CRDM) installed inside the reactor vessel has developed for use of an advanced marine reactor. This CRDM contributes to compactness and simplicity of the reactor system, and it can eliminate the possibility of a rod ejection accident. The CRDM works in the high temperature and high pressure water - 310degC and 12 MPa, the same atmosphere as the primary loop. Driving force is produced by a synchronous motor with the rotor of a permanent magnet, which has been developed. An innovative latch mechanism using separable ball nuts can latch driving shaft connecting the control rod and de-latch it for scram. The rod position detector using a magnetostrictive wire type sensor on the principle of Wiedeman effect has been developed, accuracy of which is verified to have a detecting error within 1.2 mm. Ball bearings for thrust and radial supports in rotation have been developed to be ...

International Nuclear Information System (INIS)

The dependence was determined of the decontamination factor ratio found in the presence of a carrier and in a carrier-free system on carrier concentration at different concentrations of a complexing agent in a solution. Bearing balls were used as contamination materials while a mixture of "1"5"2Eu and "1"5"4Eu isotopes was used as a contaminant, citric acid in a concentration of 5x10"-"3 to 1x10"-"1 mol/dm"3 as a complexing agent, and Eu, lanthanum and aluminium at a concentration range of 1x10"-"5 to 1x10"-"2 mol/dm"3 as carriers. While no increase in the decontamination factor was found for aluminium, a considerable increase was observed in the isotopic and homologic carriers and the concentration dependence of the carrier reached the maximum. An equation was derived explaining the effect by the isotope exchange between the contaminant and the carrier and by the reaction between the carrier and the complexing agent. (J.F.).

Energy Technology Data Exchange (ETDEWEB)

Computed tomography (CT) has been incorporated in an industrial Diode-Array Digital Radiography (DADR) system. An input data size of 512 pixel points x 400 projections yielded a 400x400 output image matrix. Reconstruction algorithms used are the filtered backprojection (FBP) and the direct Fourier reconstruction (DFR). Various filters were used in the FBP reconstruction process and their effects on image quality were evaluated. A spatial resolution of 100 {mu}m was measured with a block of plates and a minimum detectable feature size in the range of 10-100 {mu}m was measured using thin wires. Industrial specimens imaged have included ceramic samples, ball bearings and integrated circuits. A number of engineering problems have been solved, such as adjustment of the X-ray source, centering of the rotator spindle in the view field and beam-hardening corrections. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Duplex-coating procedures consisting of plasma nitriding and Me-C:H hard coating lead to an improved performance of the devices because the Me-C:H coating is supported by the nitrided phase and, therefore, the `eggshell-effect` is avoided. Furthermore, this support leads to a higher load-bearing capacity of the thin film. Two standard procedures (classical high-pressure plasma nitriding and unbalanced magnetron sputtering of Ti-C:H) were performed subsequently to prepare the duplex coatings on X20Cr13 ferritic stainless steel. The corrosion resistance of the steel could be improved by nitriding at 450 C compared to the untreated ferritic substrate. The roughness is determined by the nitriding step. The weakest point of the coating is the transition zone between the nitrided and the untreated substrate and not the interface between the Ti-C:H coating and the nitrided substrate as shown by the Rockwell and scratch tests. The adhesion of the duplex structure (plasma ...

Energy Technology Data Exchange (ETDEWEB)

Several components of high-temperature reactor units have roller bearings in order to carry out their motions without much friction. The use of such bearings poses friction and wear problems which cannot be mastered by commercial roller bearing technology. Possible improvements of coating, cage design and bearing materials as well as of their parameters were registered and studied. The service life of dry lubricated bearings was considerably improved. With a radial or axial load on the bearing of {>=} 10% of the static load, {approx_equal} 20x10{sup 6} rolling motions/actuations can be performed. The connections between surface compression and wear were determined, and optimum conditions for the transfer of lubricants from the cage onto the bearing race were worked out. Coating of corrosion-resistant roller ...

Wastenet

... The drop in pay, with mounting medical bills and a curve ball in their personal life, led Mr. Flake and his wife, Amy, to exhaust their savings. As they shifted spending to credit cards their debt mounted, and conversations about retirement ... In October 2008, they learned that a relative of hers with an 8-month-old son was going to prison. If the Flakes could not take the baby, he would be placed in foster care. The Flakes did some soul searching and decided to seek custody of ...) 1 2 Next Page »A version of this article appeared in print on March 24, 2011, on page F4 of the New York edition. Sign In to E-Mail Print Single Page Reprints Connect with The New York Times on Facebook. Get Free E-mail Alerts on These Topics Retirement Personal ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Energy Technology Data Exchange (ETDEWEB)

One aspect of the research program SFB 570 'Distortion engineering' is the in situ X-Ray diffraction analysis of phases and residual stresses during complete heat treatment cycles. These investigations result in experimental evidence available for the extensive computations. The optimisation of the instrumentation will be reported. A surface decarburisation of samples made from the ball bearing steel 100Cr6 could be avoided for a temperature range from 800 to 900 C and a holding time of one hour by a combination of evacuate the furnace and using a certain nitrogen flow as protective gas. At lower temperatures small amounts of ferrite caused by an increased diffusion rate of carbon lead again to a surface decarburisation up to a depth of 2 {mu}m. It was proved that with an evacuation of the X-Ray beam path at constant power of the X-Ray source the intensity of diffraction lines could be increased by more than a factor of 4. The ...

Energy Technology Data Exchange (ETDEWEB)

NuEra Oilfield Services Inc. combines various technologies, including advanced bearing assemblies and compact wireless decoders that interface with downhole directional tools, to engineer unique, purpose-built measurement-while-drilling (MWD) tool string packages. The 9-metre-long MWD tool string is lowered into the drill pipe from the surface. The directional module monitors the position of the drill bit, which the driller can monitor using an electronic drilling recorder at the surface. The directional drillstring uses a mud motor with adjustable bent housing to correct the direction of the well, as the system cannot steer while drilling. At bottomhole, mud circulation continues after the rotation of the drillstring has been stopped, driving the mud motor, which in turn drives the drill bit, permitting a new direction to be taken even though the drillstring is not turning. The operator points the bent housing in a new direction and slides the bit along before ...

Science.gov (United States)

Percutaneous osseointegrated prostheses are being investigated as an alternative strategy to attach prosthetic limbs to patients. Although the use of these implants has shown to be promising in clinical trials, the ability to maintain a skin seal around an osseointegrated implant interface is a major challenge to prevent superficial and deep periprosthetic infections. The specific aim of this study was to establish a translational load-bearing ovine model to assess postoperative limb compensation and gait symmetry following a percutaneous osseointegrated implant. We tested the following hypotheses: (1) the animals would return to pre-amputation limb loads within 12-months; (2) the animals would return to a symmetrical gait pattern (stride length and time in stance) within 12-months. The results demonstrated that one month following surgery, the sheep loaded their amputated limb to a mean value of nearly 80% of their pre-amputation loading condition; by 12-months, ...

British Library Electronic Table of Contents (United Kingdom)

Scuffing damage is catastrophic and typically not self-healing. It severely affects the life and reliability of engineering components, such as cams, roller bearings, piston rings, cylinder bores and gears. Gray iron and 1080 steel are important materials for these extremely demanding structural components. There have been several scuffing studies done in the past with various types of steel and cast iron. However, in these studies there was no attempt to compare the scuffing resistance of cast iron and steel materials with similar matrices. In the present study, scuffing tests were performed with the matrices of gray iron and 1080 steel being fully pearlitic. This allows for a direct evaluation of the effect of the graphite flakes on scuffing resistance. The scuffing behavior for these ma...

Science.gov (United States)

This combined analytical and experimental program is aimed at generating a manual that will permit the design of 3.0 MDN cylindrical roller bearings. The roller bearing analysis will be correlated with the results from a series of bearing tests designed t...

UK PubMed Central (United Kingdom)

A consensus definition of life remains elusive

Energy Technology Data Exchange (ETDEWEB)

The model of the supersymmetrical ball in the supersymmetrical Standard Model with additional global U(1) fermion symmetry is presented. We show that the supersymmetry breaking scale (R-parity), the global U(1) fermion symmetry scale and the electroweak symmetry breaking scale are strictly connected to each other. The realistic ball with M[approx]10[sup 5]-10[sup 9] M[sub s]un and the radius R[approx]10[sup 12]-10[sup 14] cm is obtained. Inside the ball all full symmetries are restored. The ball is stabilized by superpartners and right neutrinos which are massless inside. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Plasma nitriding is usually used for ferrous materials to improve their surface properties. Knowledge of the properties of thin surface layers is essential for designing engineering components with optimal wear performance. In our study, we investigated the microstructural, mechanical and tribological properties of plasma- and pulse plasma-nitrided AISI 4140 steel in comparison to hardened steel. The influence of nitriding case depth as well as the presence of a compound layer on its tribological behaviour was also examined. Plasma and pulse plasma nitriding were carried out using commercial nitriding processes. Nitrided samples were fully characterised, using metallographic, SEM microscopic, microhardness and profilometric techniques, before and after wear testing. Wear tests were performed on a pin-on-disc wear testing machine in which nitrided pins were mated to hardened ball bearing steel discs. The wear tests were carried out under dry ...

International Nuclear Information System (INIS)

Thermo-reactive diffusion chromizing followed by pulsed plasma nitriding were carried out on AISI 52100 and 8620 bearing steels. The chromized samples were pulse-plasma nitrided for 5 h at 500 deg. C in various N_2-H_2 gas mixtures. The coated steels were characterized using scanning electron microscopy, X-ray diffraction and microhardness testing. The unlubricated wear behaviors of only chromized and duplex treated steels were investigated in ball-on-disc system tests at room temperature. X-ray diffraction patterns of the duplex treated samples containing H_2 indicated the formation of dominant CrN and Cr_2N nitrides as well as the formation of Cr_3C_2 and Cr_7C_3 carbides. Gas mixtures in the plasma nitriding, which was performed after chromizing, have a significant influence on the wear rate of the duplex treated steels. The wear and friction tests showed that the lowest friction coefficient and wear rates were observed for the samples ...

Energy Technology Data Exchange (ETDEWEB)

A number of screening tests were performed to determine ion species that effectively reduce wear rates when implanted in four industrial steels. Ball bearing steel 100Cr6 (AISI 52100) showed a wear rate reduction by a factor of 20 when implanted with carbon dioxide to a dose of 5x10{sup 17} cm{sup -2} with a non-mass-separated ion beam and by a factor of {>=}20 when implanted with 5x10{sup 17} cm{sup -2} oxygen ions. For the ferritic and martensite steels X90CrMoV18 (AISI 440B, unhardened and hardened) also a strong wear reduction after implantation of oxygen ions was found. Co-implantation of aluminum and oxygen also reduces wear rates of X90CrMoV18, of S6-5-2 (AISI M2), and of 100Cr6, respectively. For comparison, thin oxide layers were grown in a low-temperature thermal oxidation process. These experiments also yielded reduced wear rates by a factor of 10. The surfaces were investigated and characterized by XPS, SIMS, TEM, and ...

Energy Technology Data Exchange (ETDEWEB)

In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ...

International Nuclear Information System (INIS)

NaCl doped MgCl_2.nEtOH adducts were prepared by ball-milling MgCl_2.2.5EtOH with NaCl. Both the ball-milled MgCl_2.nEtOH/NaCl mixture and pure MgCl_2.2.5EtOH adducts were analyzed by X-ray diffraction (XRD), transmission electron microscope (TEM), thermogravimetry (TG) and differencial scanning calorimetry (DSC). A simple MgCl_2.nEtOH/NaCl mixture without ball-milling treatment was also studied for comparison. Two kinds of mixed crystals, Na_2MgCl_4 and NaMgCl_3, were found to be formed in a ball-milled mixture that contained 16 mol.% NaCl. TG and DSC analysis of the samples also provided indirect evidences supporting the presence of the mixed crystals in the ball-milled mixture. Adding certain amounts of NaCl in MgCl_2.2.5EtOH adduct, either by co-milling or by simple mixing, greatly increased the thermal stability of the adduct, but thermal decomposition behaviour of the ...

International Nuclear Information System (INIS)

In order to prevent corrosion failures of machines and structures, it is desirable to know in advance when the corrosion damage will take place, and appropriate measures are needed to mitigate the damage. The corrosion predictions are needed both at development as well as operational stage of machines and structures. There are several forms of corrosion process through which varying degrees of damage can occur. Under certain conditions these corrosion processes at alone and in other set of conditions, several of these processes may occur simultaneously. For a certain type of machine elements and structures, such as gears, bearing, tubes, pipelines, containers, storage tanks etc., are particularly prone to pitting corrosion which is an insidious form of corrosion. The corrosion predictions are usually based on experimental results obtained from test coupons and/or field experiences of similar machines or parts of a structure. Considerable scatter is observed in ...

CERN Document Server

Textile machinery and accessories -- Bearings for bottom rollers and allied dimensions -- Caps with central nose and caps with side lugs

Science.gov (United States)

Mod IE did not affect the valve flow characteristics. C. BIPROPELLANT -VALVE EVALUATION. 1. Ball and Shaft Seal Evaluation ...

Energy Technology Data Exchange (ETDEWEB)

The proposed device incorporates an axle which has a roller bearing support mounted upon it. This support uses a cylindrical sleeve that comes in contact with the housing, the sensors, and the bearing support component. Metering accuracy is improved by placing roller bearing supports into grooves running through the protruding center sections of the sensor elements. These roller bearing supports interface with the cylindrical sleeve.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... PRODUCTION OF TIGHT OIL-GAS BEARING ROCKS, AND IS ALSO EMPLOYED FOR THE DEVELOPMENT OF GEOTHERMAL RESERVOIRS. ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The increasing sophistication of modern cars and todays tendency of developing compact vehicles more adapted to urban traffic have led to increased performance requirements from alternators and their bearings. This paper describes todays criteria for the design of alternators and of their bearings (improvement of tightness, design of race, grease, specific steels) and the final validation of the products. The last part of the paper describes the new CARB toroidal roller bearing developed by SKF which can support misalignments and internal axial displacements under high rotation speeds. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

The Co-Si composites with a molar ratio of 2:1 are synthesized by ball-milling method and their potential as negative electrode materials of Ni-MH batteries is investigated. The microstructure, morphology and chemical state of the ball-milled Co-Si composites are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). XRD patterns show that the ball-milled samples for 10 and 20 h contain Co, Si and Co{sub 2}Si phases, and the ball-milled samples for 40 and 60 h are mainly amorphous Co{sub 2}Si alloys. In contrast to the high initial discharge capacity (1012 mAh/g) obtained for the sample ball-milled for 10 h, the discharge capacities of the samples ball-milled for 40 and 60 h are very low. It indicates that the hydrogen storage capacity of pure Co{sub 2}Si alloy is very low. It is found that ...

Science.gov (United States)

A 206-size hybrid (ceramic/steel) cylindrical roller bearing was tested in MIL-L-23699 C oil at several speeds and loads. Heat-generation data was collected and subsequently correlated with bearing-analysis software. Bearing-cage slip data was also collected at various oil-flow rates, oil temperatures, and with both MIL-L-7808 J and MIL-L-23699 C oils. The hybrid bearing was tested in MIL-L-23699 C oil for for 25 hours at 2220 N radial load and 1.08 MDN shaft speed. The hybrid bearing technology demonstrated in the report is applicable to the Integrated High Performance Turbine Engine Technology Initiative. 15 refs.

International Nuclear Information System (INIS)

The effects of vibration isolation of the new type of mechanical damper applied to a single-degree-of-freedom system and a simple beam are discussed numerically and experimentally. The damper is composed of a ball screw, a flywheel and centrifugal brakes, and possesses nonlinear characteristics. The Continuous System Simulation Language is used for the digital simulations of the nonlinear vibration systems. The results may be summarized as follows: (1) The damper is effective for suppressing the amplitude of the single-degree-of-freedom system as well as of the beam at the point of attachment of the damper, at the resonances. (2) The damper approaches a snubber for smaller values of lead L of the ball screw (or larger values of moment of inertia J of the flywheel), and acts like a damper whose damping force is proportional to the square of the velocity for larger values of L (or smaller values of J). (author).

Energy Technology Data Exchange (ETDEWEB)

Especially in bulk goods conveying, roller bearings must be selected with a vie to the intended application. Bulk goods conveying machinery consists of many different components that must interact as perfectly as possible.

UK PubMed Central (United Kingdom)

There has been great interest in understanding the methods by which collagen-based load-bearing tissue is constructed, grown and maintained in vertebrate animals. To date, the responsibility for this...Full Text Available

International Nuclear Information System (INIS)

This study presents a dynamic analysis of a flexible rotor supported by two porous squeeze couple stress fluid film journal bearings with non-linear suspension. The dynamics of the rotor center and bearing center are studied. The analysis of the rotor-bearing system is investigated under the assumptions of non-Newtonian fluid and a short bearing approximation. The spatial displacements in the horizontal and vertical directions are considered for various non-dimensional speed ratios. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The numerical results show that the stability of the system varies with ...

Science.gov (United States)

... Tanzania, and the attack on the USS COLE. ... vis another has no bearing on the legality of the attack. If the person attacked is a combatant, the use of ...

Science.gov (United States)

... by the Bureau. A canvas of supply sources produced only one other, the Flexo roller bearing swivel. Accordingly, only the ...

Science.gov (United States)

... Title : FINITE ELEMENT OPTIMIZATION OF FIELD CONFIGURATION FOR THE EDDY CURRENT TESTING OF ROLLER BEARING RIB RINGS. ...

International Nuclear Information System (INIS)

This paper traces the development and progress of magnetic suspension systems and magnetic bearings in the USSR. The paper describes magnetic bearings for turbomachines, magnetic suspension systems for vibration isolation, some special measuring devices, wind tunnels, and other applications. The design, principles of operation, and dynamic characteristics of the system are presented.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

CERN Document Server

Quantum man

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

Seven high-school trainees each conducted training sessions with two profoundly retarded children. Each trainee was asked to teach one child to follow the instruction "Bring ball" and the other child...Full Text Available

International Nuclear Information System (INIS)

A mixture of powders of silica and aluminum nitride is subjected to high-energy ball milling for different milling times. This material is subsequently compacted by uniaxial pressing and sintered at 1450 deg. C. The resulting pellets are crushed and analysed by X-ray diffraction. For short milling times, the amount of phase transformation is minimal and the resulting material mostly consists of cristobalite and aluminum nitride. For long milling times, nanocrystalline #beta#-SiAl_2O_2N_2 is mainly produced.

Energy Technology Data Exchange (ETDEWEB)

In the present study Balb/c mice were exposed to 3,4-benzopyrene, painted on the skin every 2nd day for a total of 6 months, and simultaneously irradiated with athermal (5 mW/cm/sup 2/) or subthermal (15 mW/cm/sup 2/) doses of 2,450 MHz microwaves. The other group of animals was preirradiated with microwaves at 10 mW/cm/sup 2/ power level for 1, 2, or 3 months and then treated with benzopyrene, as above. Control mice were exposed for 6 months to benzopyrene, resulting in the development of baso- or spinocellular skin carcinoma within approximately 9 months, and sham-irradiated with microwaves. The growth of the tumour was assessed according to a self-designed 7-range macroscopic scale, supported by microscopical examinations of skin sections. All protocols of microwave irradiations resulted in a significant acceleration of the development of benzopyrene-induced skin cancer and in shortening of life span of the tumour-bearing hosts. This effect ...

Energy Technology Data Exchange (ETDEWEB)

This study presents a dynamic analysis of a rotor supported by two turbulent flow model journal bearings and lubricated with couple stress fluid under nonlinear suspension. The dynamics of the rotor center and bearing center is studied. The dynamic equations are solved using the Runge-Kutta method. The analysis methods employed in this study is inclusive of the dynamic trajectories of the rotor center and bearing center, power spectra, Poincare maps and bifurcation diagrams. The maximum Lyapunov exponent analysis is also used to identify the onset of chaotic motion. The results show that the values of dimensionless parameters l* strongly influence dynamic motions of bearing and rotor centre. It is found that couple stress fluid improve the stability of the system when l* > 0.4 even if the flow of this system is turbulent. We also demonstrated that the dimensionless rotational speed ratios s and ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes effects of methods to calculate and analyze bearing capacities and transformation of pile foundations in the limit state design method. Different pile bearing capacity estimating expressions including criteria used in other countries were applied to the case of steel piles driven into the `diatomaceous mudstone ground` in Noto Peninsula, Ishikawa Prefecture where detailed ground and soil surveys have been made, and the case of piles driven in place into the `sandy and clayish soil alternating ground layers` at the Tennoji area in Osaka Prefecture. The results were compared with those of static loading tests. As a result, the estimated bearing capacity limit was found to agree relatively well with the measured values where uniaxial compression strength was used according to the reference architectural formula. The estimated bearing capacity limit using the N-value as the soil ...

Energy Technology Data Exchange (ETDEWEB)

BC Hydro recently conducted a demonstration test of a bearing condition monitor. The test, at the 529-MW Kootenay Canal project, proved the ability of the monitor to detect machine condition faults. The capability to detect changing conditions during normal operation of hydroelectric machines gives hydro plant owners the opportunity to anticipate needed maintenance and ultimately to reduce the number of equipment failures. BC Hydro intends to install bearing condition monitors, as well as windings monitors, brushgear monitors, environmental monitors, and other selected systems in as many as 46 of its hydro generators. BC Hydro analyzed forced outages between 1985 and 1989 in its hydro system to identify which parts of a generating unit resulted in the highest number of hours of outage. From there, the utility has formulated a concept for a machine condition monitoring system. To keep the system cost effective, it will be developed in modules. ...

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this study was to identify, characterize, and map the wetlands in the Bear Creek watershed. A preliminary wetland categorization system based on the Cowardin classification system (Cowardin et al. 1979) with additional site-specific topographic, vegetation, and disturbance characteristic modifiers was developed to characterize the type of wetlands that exist in the Bear Creek watershed. An additional objective was to detect possible relationships among site soils, hydrology, and the occurrence of wetlands in the watershed through a comparison of existing data with the field survey. Research needs are discussed in the context of wetland functions and values and regulatory requirements for wetland impact assessment and compensatory mitigation.

Science.gov (United States)

Deer Elk Bighorn Sheep American Pronghorn Moose Deer Mouse Carnivores Bobcat American Badger River Otter Red Fox Long-Tailed Weasel Coyote Grizzly Bear Mountain Lion Amphibians...

Energy Technology Data Exchange (ETDEWEB)

Recent progress in yttrium-based oxide high-temperature superconductors has enabled the production of a large diameter bulk with a strong flux-pinning force. A combination of this superconductor and a permanent magnet makes it feasible to fabricate a noncontact, non-controlled superconducting magnetic bearing with a very small rotational loss, applicable to a flywheel energy storage system. A conceptual design of an 8 MWh flywheel energy storage system using the new bearing has been developed, based on measured data on a miniature bearing model, which proved to be potentially capable of achieving a high energy storage efficiency of 84 pc. A 100 W h-class experimental system was then built, which attained a high revolution rate of 17000 rpm, with a rotational loss of about 0.6 W. (authors). 2 refs., 7 figs., 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

Roller bearing is one of the most widely used elements in rotary machines. Condition monitoring of such elements is conceived as pattern recognition problem. Pattern recognition has three main phases: feature extraction, feature selection and feature classification. Histogram features can be used for fault diagnosis of roller bearing. This paper presents the use of decision tree for selecting best few histogram features (bin ranges) that will discriminate the fault conditions of the bearing from given train samples. These features are extracted from vibration signals. A rule set is formed from the extracted features and fed to a fuzzy classifier. The rule set necessary for building the fuzzy classifier is obtained largely by intuition and domain knowledge. This paper also presents the usag...

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

Science.gov (United States)

replacing the KDP crystal, and introducing computer programs for accumulation of an almost unlimited number of frames. The calibration procedure using solar ...

UK PubMed Central (United Kingdom)

Life history theory proposes that early-life cues induce highly integrated responses in traits associated with energy partitioning, maturation, reproduction, and aging such that the individual phenotype...Full Text Available

UK PubMed Central (United Kingdom)

Life-history theory predicts that traits involved in maturity, reproduction and survival correlate along a fast–slow continuum of life histories. Evolutionary theories and empirical results...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Cu/YSZ cermet (40 and 60 vol.% Cu powder with balance YSZ) is a more economical cathode material than the conventional Ni/YSZ cermet for high temperature electrolysis (HTE) of water vapor and it was successfully fabricated by high-energy ball-milling of Cu and YSZ powders, pressing into pellets (o 13 mm x 2 mm) and subsequent sintering process at 700 deg. C under flowing 5%-H{sub 2}/Ar gas. The Cu/YSZ composite material thus fabricated was characterized using various analytical tools such as XRD, SEM, and laser diffraction and scattering method. Electrical conductivity of sintered Cu/YSZ cermet pellets thus fabricated was measured by using 4-probe technique for comparison with that of conventional Ni/YSZ cermets. The effect of composite composition on the electrical conductivity was investigated and a marked increase in electrical conductivity for copper contents greater than 40 vol.% in the composite was explained by percolation threshold. Also, Cu/YSZ cermet was ...

UK PubMed Central (United Kingdom)

Purpose. Formation of a tracheoinnominate artery fistula (TIF) and consecutive hemorrhage is a rare and life-threatening complication with high mortality. Warning symptoms can...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Drosophila melanogaster is a model organism rich in genetic tools to manipulate and identify neural circuits involved in specific behaviors. Here we present a technique for two-photon calcium imaging in the central brain of head-fixed Drosophila walking on an air-supported ball. The ball's motion is tracked at high resolution and can be treated as a proxy for the fly's own movements. We used the genetically encoded calcium sensor, GCaMP3.0, to record from important elements of the motion-processing pathway, the horizontal-system lobula plate tangential cells (LPTCs) in the fly optic lobe. We presented motion stimuli to the tethered fly and found that calcium transients in horizontal-system neurons correlated with robust optomotor behavior during walking. Our technique allows both behavior ...

International Nuclear Information System (INIS)

A steadily increasing part of comminution is nowadays carried out by tube ball mills. Our investigations are a first step to a possible tuning of material distribution with mechanical stress characteristic of the grinding media charge, that is essential for a high efficiency of grinding. A BOND mill filled with porcelain balls as grinding media and labelled corundum (Au-198) as grinding material was used to measure the distribution of material over the cross-section. The evaluation was made by linear interpolation between all combinations of adjacent measuring points to calculate all coordinates with equal intensity for each selected level of activity. Two plottings showing the dependence of material distribution on the rotating speed are presented. (author).

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Ultrafine particles of Co-P were synthesized by direct ball milling of Co and P powders and also investigated as a reversible hydrogen storage electrode material. The electrochemical results demonstrated that the reversible charge-discharge capacity of the Co-P electrode can reach more than 300mAh/g. In addition, the cycling ability and high rate capability of the Co-P electrode are excellent with only 5% capacity decay after 100 cycles at a high rate of 300mA/g. The temperature-programmed desorption measurements (TPD) of the Co-P electrode revealed that the charge and discharge reactions of the Co-P electrode proceeds predominantly through electrochemical hydrogen storage mechanism and the electrooxidation of cobalt contributes only a negligible part to the reversible electrochemical capacity. (author)

Energy Technology Data Exchange (ETDEWEB)

The aims of the work described here were to provide an experimental basis for evaluating the committed effective dose equivalent per unit intake together with the ALI for four industrial oxide bearing dusts, and to assess the extent to which {sup 241}Am could be used for estimating the {sup 239}Pu content of the lung after an accidental intake of these materials. (author).

International Nuclear Information System (INIS)

The paper considered the vibration signals of rotating equipment as cyclo stationary signals through analyzing the features of this kind of signals. Based on the analytic method of cyclic spectrum density, the paper pointed out that the impact frequency could be extracted effectively with the help of scanning cyclic frequency domain. The validity of the method of cyclic spectrum density is proved by simulating signals and the method is applied to the diagnosis of rolling bearings. (authors)

Science.gov (United States)

... 2,000 230.102Tender plain bearing journal boxes: Failure to repair 1,000 1,500 230.103Tender roller bearing journal boxes: Failure to properly maintain 1,000 1,500 230.104Driving box shoes and wedges:...

CERN Document Server

Work and family--allies or enemies?

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

We describe the architecture of LifeCode® (A-Life Medical, Inc.), a natural language processing system for free-text clinical information extraction, our methodology in applying LifeCode®...Full Text Available

International Nuclear Information System (INIS)

... actinides americium 241 americium 242 americium 243 calibration standards

UK PubMed Central (United Kingdom)

The generation of synthetic forms of cellular life requires solutions...Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The behaviour of an elastomeric seal for vehicle brake Tandem master cylinder is measured and analyzed in temperature and brake fluids changed. Working conditions are simulated for different piston rod velocity and cylinder supply pressure, in temperature rising, brakefluid boundary and Nanoaluminum oxide brakefluid oxide brakefluid lubrication. The result shows that Nanoaluminum oxide brakefluid with its ball shape can highly reduce friction coefficient to avoid seal excessive wear and reduce slick slip in brake applications.

British Library Electronic Table of Contents (United Kingdom)

We prove that Formula Not Shown surface diffeomorphisms have symbolic extensions, i.e. topological extensions which are subshifts over a finite alphabet. Following the strategy of Downarowicz and Maass (Invent. Math. 176:617?636, 2009) we bound the local entropy of ergodic measures in terms of Lyapunov exponents. This is done by reparametrizing Bowen balls by contracting maps in a approach combining hyperbolic theory and Yomdin?s theory.

Energy Technology Data Exchange (ETDEWEB)

We consider the case of a test sphere (ball) of radius a{sub 1} rotating at constant angular velocity {omega} in an otherwise quiescent unbounded suspension of uniformly sized spheres of radii a{sub 2} dispersed in a Newtonian fluid of viscosity {mu}. To the first order in the volume fraction c of suspended spheres it is shown that when the ball is small compared with the suspended spheres the suspension does not behave as regards the hydrodynamic torque L exerted on the ball like a homogeneous Newtonian fluid characterized by the usual Einstein viscosity coefficient {mu}{sub s}={mu}(1+5/2c). Explicitly, the torque on the rotating sphere does not obey Kirchoff{close_quote}s law, L=8{pi}{mu}{sub s}a{sub 1}{sup 3}{omega} for no slip. Rather, a modified form of Kirchoff{close_quote}s law is obtained in which the Einstein coefficient of 5/2 is multiplied by a coefficient which is less than unity in magnitude and is functionally ...

International Nuclear Information System (INIS)

More than sixty base-isolated buildings have been built in Japan. A number of base-isolation systems were considered in our research, which was intended to establish the effectiveness of base-isolation systems. We conducted research on silicone rubber bearings. Generally, silicone rubber is durable and its characteristics are not dependent on the temperature within the relevant design range. The first part of the report covers material and elements testing. After the bearings were installed in the building, we performed forced vibration tests in both the horizontal and vertical directions. These test results form the next section. After several experiments, we carried out earthquake observations. We report on the effectiveness of the system in reducing response acceleration during a small displacement. This system was installed in the building in March 1992

British Library Electronic Table of Contents (United Kingdom)

The ensemble empirical mode decomposition (EEMD) can overcome the mode mixing problem of the empirical mode decomposition (EMD) and therefore provide more precise decomposition results. Wavelet neural network (WNN) possesses the advantages of both wavelet transform and artificial neural networks. This paper combines the merits of EEMD and WNN to propose an automated and effective fault diagnosis method of locomotive roller bearings. First, the vibration signals captured from the locomotive roller bearings are preprocessed by EEMD method and intrinsic mode functions (IMFs) are produced. Second, a kurtosis based method is presented and used to select the sensitive IMF. Third, time- and frequency-domain features are extracted from the sensitive IMF, its frequency spectrum and its envelope spe...

British Library Electronic Table of Contents (United Kingdom)

This study was designed to identify the relationship between free time management and quality of life, exploring whether the amount of free time or the way people using their free time relates to their quality of life. Data were collected from National Pingtung University of Science and Technology in Taiwan. Of the 500 questionnaires distribute, 403 usable questionnaires were received with an 81% response rate. The result has found a positive relationship between free time management and quality of life. Contrary to this, there was no significant relationship between time allocation and quality of life. Results might indicate that people who manage their free time well lead to better quality of life. Suggestions based on the observed relationship and directions for future researches were d...

Science.gov (United States)

The patent application describes an anti-friction worm-wheel assembly wherein the anti-friction elements are rollers carried by the worm element. The rollers sequentially move through grooves in the edge surface of the wheel element to transmit drive forc...

Science.gov (United States)

A Pd(0)-catalyzed intramolecular Heck-type reaction of oxime ether has been developed, providing convenient access to heterocyclic oximes. PMID:21964259

UK PubMed Central (United Kingdom)

BackgroundOil palm (Elaeis guineensis Jacq.) is one of the most important oil bearing crops in the world. However, genetic improvement of oil palm through conventional...Full Text Available

UK PubMed Central (United Kingdom)

MicroRNAs (miRNAs) are endogenously encoded small noncoding RNAs, derived by processing of short RNA hairpins, that can inhibit the translation of mRNAs bearing partially complementary target sequences....Full Text Available

Science.gov (United States)

This paper presents a novel feature extraction scheme for roller bearing fault diagnosis utilizing generalized S transform and two-dimensional non-negative matrix factorization (2DNMF). The generalized S transform, which can make up the poor energy concentration of the standard S transform, is introduced to generate the time-frequency representation (TFR). Experiment results on simulated signal and vibration signals measured from rolling element bearings have revealed that the generalized S transform can obtain a more satisfactory TFR than other similar techniques. Furthermore, a new technique called two-dimensional non-negative matrix factorization (2DNMF), which can reduce the computation cost and preserve more structure information hiding in original 2D matrices compared to the NMF, is developed to extract more informative features from the time-frequency matrixes for accurate fault classification. Experimental results on ...

UK PubMed Central (United Kingdom)

In response to oxidative stress, the transcription factor NF-E2-related factor 2 (Nrf2) controls the fate of cells through transcriptional upregulation of antioxidant response element (ARE)-bearing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Since bearing is in wide use as basic parts for rotary machines, detection and diagnosis of its defects are important in practical use. To discriminate defect portions by early detection of roller bearing flaking, the conventional parameter method using peakedness is poor. Thus to directly obtain difference in waveform, the new method was applied to such detection which uses KDI as the scale of a difference in waveform, and a most neighborhood classification rule based on KDI. The detection and discrimination abilities of this method was studied mainly in experiment. The experiment used a bench scale rotor and a supporting bearing, and attempted detection and discrimination of no flaking, outer ring flaking and inner ring flaking. As a result, this method could detect and discriminate fine flaking which was never detected by conventional method. Since selection of standard data is essential for this method, a distance ratio ...

UK PubMed Central (United Kingdom)

Gamma interferon (IFN-γ) and the cellular responses induced by it are essential for controlling mycobacterial infections. Most patients bearing an IFN-γ receptor ligand-binding chain...Full Text Available

International Nuclear Information System (INIS)

The major details of the inspection and replacement of the bearing journals on each of the four heat transport pumps (HTPs) at Wolsung nuclear generating station in Korea are presented in this paper. Investigation following fracture of one of the journals in 1985 revealed that it was excessively hard. The journal material (ASTM A296 CA 40) is considered to be prone to stress corrosion fatigue if the hardness exceeds Rc 40. In 1986 May, during a planned outage, the HTPs were disassembled, the journals were inspected, found to be excessively hard, and all were replaced. At the same time, the pump to motor couplings were all refurbished to ensure proper alignment.

Energy Technology Data Exchange (ETDEWEB)

A manipulator for checking the inside of a vertical, flange-shaped collector of a horizontal steam generator consists of a rotating mast with bearings at the top and bottom ends with a support that can be moved along the length of the mast for the checking system mountings. The support is propelled by a drive spindle placed parallel to the mast with its drive head bearing in the support and locked into a toothed rack attached to the mast. The checking system mountings are fitted in or on the walls of the support and are very close to the box-shaped support. Their retractable arms are hinged.

Energy Technology Data Exchange (ETDEWEB)

The invention concerns the conversion of steam turbines, particularly condensation turbines, for the economic coupling of process steam and heating steam. The conversion occurs by retaining the basic construction of foundations, housing and bearings as support group and coupling member and matching the specially developed construction for the idea of use into the existing housing, and inserting the rotor into the shaft unit. By having the unchanged supports of the housing and the bearings of the shaft unit, the elasticity in expansion and the vibration behaviour of the turbine are retained and the conversion costs can be lowered.

UK PubMed Central (United Kingdom)

The study of the origin of life covers many areas of expertise and requires the input of various scientific communities. In recent years, this research field has often been viewed as part of a broader...Full Text Available

UK PubMed Central (United Kingdom)

ObjectivesThe objective of this paper is to describe the complex mixed-methods design of a study conducted to assess health-related quality of life (HRQOL) outcomes...Full Text Available

UK PubMed Central (United Kingdom)

Depending on the species, the end of flower life span is characterized by petal wilting or by abscission of petals that are still fully turgid. Wilting at the end of petal life is due to programmed...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundHeterogeneous results for research investigating health-related quality of life (HRQL) in patients undergoing sphincter-ablating procedures for rectal cancer...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVE: The aim was to assess the psychosocial effects on the quality of life (QOL) of adults with head and neck cancer (HNC) and any gender variations with predictive factors that may influence...Full Text Available

UK PubMed Central (United Kingdom)

SummaryBackgroundQuality of life among women with irritable bowel syndrome may be affected by pelvic floor disorders.AimFull Text Available

UK PubMed Central (United Kingdom)

BackgroundAlthough considerable progress has been made in the treatment of chronic kidney disease, compromised quality of life continues to be a significant problem for patients...Full Text Available

UK PubMed Central (United Kingdom)

SummaryBody condition affects the timing and magnitude of life history transitions. Therefore, identifying proximate mechanisms...Full Text Available

UK PubMed Central (United Kingdom)

There is increasing evidence for an empiric link between late-life depression and Alzheimer disease (AD). The neuropathology of AD, previously only confirmed at autopsy, may now be detectable...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundMigrants everywhere face several demands for health and maintaining good health and quality of life could be challenging. Iraqis are the second largest refugee group that...Full Text Available

UK PubMed Central (United Kingdom)

Studies in mammals have led to the suggestion that hyperglycemia and hyperinsulinemia are important factors both in aging and in the development of cancer. It is possible that the life-prolonging effects...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVES: To assess the subjective quality of life (QOL) of family caregivers of Sudanese type-1 and type-2 diabetic outpatients, using the WHO 26-item QOL instrument, compared with a general population...Full Text Available

UK PubMed Central (United Kingdom)

The ethical dimension of treating the elderly, including risk–benefit analysis, focuses mainly on quality of life and end-of-life issues. These include arguments on advance directives and the...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThe effects of intervention programs on health-related quality of life (HRQOL) of patients with hip fracture have not been well studied. We hypothesized that older patients...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline cemented tungsten carbide has attracted considerable interests for use in cutting tool because of its superior mechanical properties. In this study, nano-sized powders of mixed WC and Co were prepared from attrition-milled oxides by a gas reduction-carburization process. The effects of compacting pressure, heating schedule, additional ball-milling, and the presence of a grain growth inhibitor on the sintering properties of the nano-sized WC-Co powders were examined. The grain size and phases in WC-Co alloy were clearly affected by compacting pressure. Because of the trapped gases and the lower melting point of the cobalt binder, when a compact of nano-sized WC-Co powder was sintered through a heating schedule with holding steps, the sintered alloy maintained the small size of WC grains without any {eta} phase. In addition, the additional ball-milling improved the microstructure and mechanical properties of the nano-sized WC-Co ...

International Nuclear Information System (INIS)

... electrophoresis fission products gamma radiation gamma spectra half-life

British Library Electronic Table of Contents (United Kingdom)

Abstract Ionizing radiation is a ubiquitous feature of the Cosmos, from exogenous cosmic rays (CR) to the intrinsic mineral radioactivity of a habitable world, and its influences on the emergence and persistence of life are wide-ranging and profound. Much attention has already been focused on the deleterious effects of ionizing radiation on organisms and the complex molecules of life, but ionizing radiation also performs many crucial functions in the generation of habitable planetary environments and the origins of life. This review surveys the role of CR and mineral radioactivity in star formation, generation of biogenic elements, and the synthesis of organic molecules and driving of prebiotic chemistry. Another major theme is the multiple layers of shielding of planetary surfaces from th...

International Nuclear Information System (INIS)

... 67 gamma detection hafnium 180 half-life indium 111 iodine 125 iodine 131

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

... Safety Institute, GRS, Cologne (Germany) INIS-UA--089 456 p. APPLIED LIFE

International Nuclear Information System (INIS)

... e Biologia Molecular (SBBq), Sao Paulo, SP (Brazil) 217 p. APPLIED LIFE

International Nuclear Information System (INIS)

... charges energy levels gamma spectra half-life isomeric nuclei kev range

Energy Technology Data Exchange (ETDEWEB)

A study was made of the variation in strength characteristics of group IV transition metal carbon nitrides alloyed with carbides or group V metal nitrides. A complex solid solution of titanium-niobium carbonitride was preliminarily synthesized to a homogeneous equilibrium state and then crushed. The calculated quantity of binder metal was added as elemental powders, the mixture was vibration ball milled in ethanol and the plasticized charge was used to press experimental specimens for mechanical testing. The studies showed that the high-temperature strength properties of the new cermet are superior to standard type KNT. The material is thus promising for use in the manufacture of tools. 8 references, 3 figures.

International Nuclear Information System (INIS)

The radiation life time of reactor pressure vessel (RPV) is the most important limiting factor for the term of exploitation of the whole power unit. The main degradation mechanism of RPV metal is the neutron induced embrittlement. Processes of radiation ageing running in RPV metal lead to fracture toughness decrease and to increased probability of brittle fracture of the vessel under thermal shocks. This explains the importance of RPV integrity assessment and rest life time management

International Nuclear Information System (INIS)

"1"0"1Mo is an important radionuclide to determine the burn-up of nuclear fuels, but its half-life reference values had marked differences. It is described in detail the principles and processes of the position normalization method by two high purity germanium detectors to determinate the half-life of "1"0"1Mo. (authors)

Science.gov (United States)

The need for cost effective, high performance, long life capacitors with improved reliability is discussed. It is shown that a low cost, miniature aluminum capacitor, with improved reliability and proven life, can be produced with existing technology. It is further shown that the capacitor can be specified for 125 C life and shelf test requirements, and meet established standards for their parametric performance.

Energy Technology Data Exchange (ETDEWEB)

A work on the world of astrophysics primarily for lay readers. The author writes only about the discoveries he ''experienced'' during the past 25 years (before 1979). Illustrated somewhat in color plus a set of superb colar plates. Contents, abridged: The long life of stars. The life story of the sun. The life story of massive stars. The end of stars. How stars are born. Planets and their inhabitants.

Energy Technology Data Exchange (ETDEWEB)

Composite particles represented as TiV{sub 2.1}Ni{sub 0.3}-Raney Ni(R) were prepared by ball-milling a TiV{sub 2.1}Ni{sub 0.3} alloy with Raney Ni in the presence of 0.01 M sodium hypophosphite (NaH{sub 2}PO{sub 2}) aqueous solution as a reducing agent. The composite particles had different morphology from original TiV{sub 2.1}Ni{sub 0.3} alloy particles and TiV{sub 2.1}Ni{sub 0.3}-Raney Ni composite particles prepared by the ball-milling in the absence of the NaH{sub 2}PO{sub 2} aqueous solution. In charge-discharge cycle tests, the TiV{sub 2.1}Ni{sub 0.3}-Raney Ni(R) composite electrode showed the maximum discharge capacity of 620 mAh g{sup -1}, while its cycle durability was similar to the TiV{sub 2.1}Ni{sub 0.3} alloy electrode, which was explained from depth profiles of constituent elements by Auger electron spectroscopy (AES). In thermogravimetry (TG) and differential thermal analysis (DTA), two steps of dehydriding for hydrided TiV{sub ...

Energy Technology Data Exchange (ETDEWEB)

We examined a catalytic effect of niobium oxide (Nb{sub 2}O{sub 5}) on the hydrogen storage properties of MgH{sub 2} prepared by mechanical ball milling method. The MgH{sub 2} composite doped with 1 mol% Nb{sub 2}O{sub 5} by ball milling for 20 h desorbed hydrogen up to {approx}6 mass% in the temperature range from 200 to 250 {sup o}C at the heating rate of 5 {sup o}C/min under a purified helium flow. After dehydrogenation at 200 {sup o}C, the product showed remarkable hydrogen absorption kinetics. A large amount of gaseous hydrogen up to {approx}4.5 mass% was absorbed even at room temperature under 1 MPa hydrogen pressure within 15 s and finally its capacity reached up to 5 mass%. Furthermore, the valence state of Nb{sub 2}O{sub 5} doped in MgH{sub 2} was examined by X-ray absorption near edge structure (XANES) measurement. The results indicated that additive Nb{sub 2}O{sub 5} was reduced by MgH{sub 2} during mechanical milling. This suggests ...

British Library Electronic Table of Contents (United Kingdom)

Given the important role of parent-youth communication in adolescent well-being and quality of life, we sought to examine the relationship between specific communication variables and youth perceived quality of life in general and as a deaf or hard-of-hearing (DHH) individual. A convenience sample of 230 youth (mean age = 14.1, standard deviation = 2.2; 24% used sign only, 40% speech only, and 36% sign + speech) was surveyed on communication-related issues, generic and DHH-specific quality of life, and depression symptoms. Higher youth perception of their ability to understand parents' communication was significantly correlated with perceived quality of life as well as lower reported depressive symptoms and lower perceived stigma. Youth who use speech as their single mode of communication ...

British Library Electronic Table of Contents (United Kingdom)

Summary 1. A primary goal of evolutionary ecology is to understand factors selecting for the diversity of life histories. Life-history components, such as time-to-reproduction, adult survivorship and fecundity, might differ among species because of variation in direct and indirect benefits of these life histories in different environments or might have lower-than-expected variability because of phylogenetic constraints. Here, we present a phylogenetic examination of demography and life histories using a data base of 204 terrestrial plant species. 2. Overall, statistical models without phylogeny were preferred to models with phylogeny for vital rates and elasticities, suggesting that they lacked phylogenetic signal and are evolutionarily labile. However, the effect of phylogeny was signific...

Energy Technology Data Exchange (ETDEWEB)

In order to improve the well-known short operational life time of BF3 counters, three potential adsorbents for impurity gases (graphite, activated charcoal and a zirconium-aluminum mixture) were introduced into BF3 counters in the form of coating on the aluminum cathode surface. Tests in el fields revealed that a partial coating of activated charcoal provides the best result. The improvement of their operational life in el fields was about three orders of magnitude in terms of tolerable exposure. Many counters with a partial coating of activated charcoal were further tested from the following viewpoints: background noise, vibration and shock, el pulse discrimination, operational life in a neutron field and non-operational in-reactor exposure life. The results were satisfactory for reactor control and protection usage. (author).

Science.gov (United States)

This study explored adolescents' sexual self-disclosure in real life and cyberspace, as well as gender differences of sexual self-disclosure in cyberspace. There were 115 male and 92 female adolescents who participated in this pretest and posttest survey. In general, the depth of sexual self-disclosure in real life was greater than in cyberspace, but the breadth of sexual selfdisclosure in both real life and cyberspace was equivalent. The cross-lagged panel analysis indicated that adolescents who were willing to self-disclose sexual topics in real life also selfdisclosed them more in cyberspace, and vice versa. Furthermore, sexual self-disclosure in both disclosing environments was mutually predicted by each other. The findings also indicated that cyberspace might not be a substitute channel of compensatory gratification for sexual self-disclosure in real life. As for gender ...

Science.gov (United States)

The contents of this report covers: (1) development of optimal geometries for crowned helical gears; (2) a method for their generation; (3) tooth contact analysis (TCA) computer programs for the analysis of meshing and bearing contact of the crowned helical gears; and (4) modelling and simulation of gear shaft deflection. The developed method for synthesis was used to determine the optimal geometry for a crowned helical pinion surface and was directed to localize the bearing contact and guarantee favorable shape and a low level of transmission errors. Two new methods for generation of the crowned helical pinion surface are proposed. One is based on the application of a tool with a surface of revolution that slightly deviates from a regular cone surface. The tool can be used as a grinding wheel or as a shaver. The other is based on a crowning pinion tooth surface with predesigned transmission errors. The pinion tooth surface can be generated by ...

Energy Technology Data Exchange (ETDEWEB)

Clay-based materials can be cold-stabilized using binder and formed by extrusion. This paper deals with the properties of such materials under the influence of silico-aluminous flying ashes addition. Flying ashes are solid industrial wastes produced by coal combustion. Characteristics of ashes bearing clay-based products, such as dimensional stability, water and mechanical resistance, accelerated aging, are considerably improved with respect to simple clay-binder mixtures. This is principally due to a better hydration of the binder in ashes-bearing mixtures because of: a higher free-water availability as a consequence of the smaller specific surface of ash grains, the filler effect of ash grains which do not participate to the reactions, the specific property of silico-aluminous ashes that can fix the lime in presence of water to produce hydrated compounds. These ashes-bearing clay based materials can have the same ...

Energy Technology Data Exchange (ETDEWEB)

Recent work has been carried out on development of isotope wear analysis and optical and eddy current technologies to provide bearing wear measurements and real time monitoring of shaft speed, shaft axial displacement and shaft orbit of the Orbit Transfer Vehicle hydrostatic bearing tester. Results show shaft axial displacement can be optically measured (at the same time as shaft orbital motion and speed) to within 0.3 mils by two fiberoptic deflectometers. Evaluation of eddy current probes showed that, in addition to measuring shaft orbital motion, they can be used to measure shaft speed without having to machine grooves on the shaft surface as is the usual practice for turbomachinery. The interim results of this condition monitoring effort are presented.

Science.gov (United States)

A novel approach to fault diagnosis is proposed using multiscale morphology analysis to extract impulsive features from the signals with strong background noise. Multiscale morphology is applied to one-dimensional signal by defining both the length and height scales of structuring elements (SEs). A local-peak-value based adaptive algorithm is also introduced. The new approach makes the selection of SEs more transparent and is independent of empirical rules. Both simulated impulsive and vibration signals of two defective roller bearings are employed to validate the proposed algorithm. The roller bearing faults presented in the validation include both inner and outer race faults. The test results show that the multiscale morphology analysis is effective and robust to extract morphological features.

CERN Document Server

In this paper we examine the relationship between covariance and unitarity for quantum gravity in Ashtekar variables. A usual description would discard half of the original Lorentz group, in exchange for the resulting simplifications of general relativity. We start by quantizing a trivial SL(2,C) gauge theory resulting in a nonunitary covariant theory. By the addition of a total time derivative we transform this into a unitary theory of the Ashtekar description of gravity with complete accountability of the degrees of freedom. We find that covariance on the spacetime level bears a direct relationship to covariance on the level ofthe quantum fields themselves. This procedure can in principle be applied to any totally constrained system, and bears a resemblance to the Gupta--Bleuler method. Finally, we make some observation regarding the loop representation of the SL(2,C) connection.

Energy Technology Data Exchange (ETDEWEB)

The invention is associated with organic geochemistry and may be used in conducting geological exploration operations for oil and gas. The purpose of the invention is to increase the precision of the method for determining the genesis of bitumoids. This is achieved through determining the isotopic composition of nickel or vanadium and from the anomalously high values of the isotopic ratio of Ni-58 to Ni-62 or from the anomalously low values of the isotopic ratio of vanadium, a conclusion is drawn about the epigenetic nature of the bitumoids. The proposed method is characterized by greater resolution due to the fact that the values of the isotopic ratios for oil bearing and water bearing structures are essentially not superimposed. The proposed method exceeds the resolution of metal metering studies in conducting geological exploration for oil and gas by 2 to 3 times.

CERN Document Server

The origin of life and the origin of the universe represent two of the most important problems of science. Both are resolved by hydro-gravitational dynamics (HGD) cosmology (Gibson 1996, Schild 1996, Gibson 2009ab), which predicts frozen primordial hydrogen-helium gas planets in clumps as the dark matter of galaxies. Merging Earth-mass planets formed stars, moons and comets to incubate and cosmically seed the first life. Cometary panspermia (Hoyle and Wickramasinghe 1981, 1982; Wickramasinghe et al. 2009) occurs naturally by HGD mechanisms. Comets and moons are fragments from mergers of stardust covered frozen gas planets in their step-wise growth to star mass. Supernovae from stellar over-accretion of planets produce stardust (C, N, O, P etc.) chemical fertilizer. Planets collect this infected radioactive dust gravitationally, to provide liquid water domains in contact with life nutrients seeded with ...

Energy Technology Data Exchange (ETDEWEB)

An explanation is given of life estimation of CV cable and OF cable which are generally used as high-voltage power cable. CV cable uses XLPE (crosslined polyethylene) and OF cable uses oil-immersed paper as electrical insulators. Relating to CV cable, voltage deterioration due to partial discharge and electric treeing occurs in a high electric field, and by extrapolating the data of up to the actually used electric field in this high electric field, the life is estimate (there is an n-power deterioration law which is V{sup n} = t between breakdown voltage V and electric applied time t). Validity of this extrapolation, however, is a future issue. Further, in the use under the immersion condition, water tree deterioration phenomena influenced by water content and the electric field which are characteristic of CV cable are seen even in the actually used low electric field, and the life index becomes considerably small. ...

Energy Technology Data Exchange (ETDEWEB)

A life cycle assessment was performed to quantify the non-renewable (fossil) energy use and global warming potential (GWP) in electricity generation from a typical gas fired combined cycle power plant in Singapore. The cost of electricity generation was estimated using a life cycle cost analysis (LCCA) tool. The life cycle assessment (LCA) of a 367.5 MW gas fired combined cycle power plant operating in Singapore revealed that hidden processes consume about 8% additional energy in addition to the fuel embedded energy, and the hidden GWP is about 18%. The natural gas consumed during the operational phase accounted for 82% of the life cycle cost of electricity generation. An empirical relation between plant efficiency and life cycle energy use and GWP in addition to a scenario for electricity cost with varying gas prices and plant efficiency have been established.

CERN Document Server

The determinants of the velocity of money have been examined based on life-cycle hypothesis. The velocity of money can be expressed by reciprocal of the average value of holding time which is defined as interval between participating exchanges for one unit of money. This expression indicates that the velocity is governed by behavior patterns of economic agents and open a way to constructing micro-foundation of it. It is found that time pattern of income and expense for a representative individual can be obtained from a simple version of life-cycle model, and average holding time of money resulted from the individual's optimal choice depends on the expected length of relevant planning periods.

Energy Technology Data Exchange (ETDEWEB)

This study was initiated to provide empirical data and analyses on the dam passage timing, travel rate, survival, and life history variation of fall Chinook salmon that are produced in the Clearwater River. The area of interest for this study focuses on the lower four miles of the Clearwater River and its confluence with the Snake River because this is an area where many fish delay their seaward migration. The goal of the project is to increase our understanding of the environmental and biological factors that affect juvenile life history of fall Chinook salmon in the Clearwater River. The following summaries are provided for each of the individual chapters in this report.

Energy Technology Data Exchange (ETDEWEB)

The fatigue properties of EP539LM alloy with an Al-Nb-Si fused slurry coating and a Co-Cr-Al-Y electron-beam coating are investigated experimentally in vacuum and in air at 900 C. It is found that the protective coatings reduce the fatigue life of the specimens both in vacuum and in air, with the electron-beam coating affecting the fatigue life of the alloy to a lesser degree than the fused slurry coating. The negative effect of the coatings on the fatigue life of the alloy is attributed largely to the properties of the coating material. 7 references.

British Library Electronic Table of Contents (United Kingdom)

Abstract The creation of chirality on Earth and the development of chiral life have been discussed in this highlight. Convincing evidence for the introduction of chirality on Earth is still fragmentary. We believe that by a combination of chiral crystallization and formation of helical polymers with preferred chiral conformational structure is the key to this question. This concept of macromolecular asymmetry has inspired ideas and resulted in possible rules for how chiral life as we know it, could have been introduced. These investigations needed the understanding of the requirements for chiral crystallization, for the stereochemistry of the initial formation of helical polymers, the measurements of optical activity of solids and their coordination with the fundamentals of chirality. Spac...

Science.gov (United States)

Joint Committee on Atomic Energy. Comgress of the United States. Washington, D. C.. 1 - Chief, Life Sciences Division. A m y Research Office ...

International Nuclear Information System (INIS)

... 16, 2001 0006-2979 BIORAK v. 40(2) APPLIED LIFE SCIENCES azido

International Nuclear Information System (INIS)

... bollworm fertility gamma radiation genetic radiation effects life span mating

UK PubMed Central (United Kingdom)

Although the life expectancy of thalassemia patients has markedly improved over the last few decades, patients still suffer from many complications of this congenital disease. The presence of a high...Full Text Available

Science.gov (United States)

Regional Information: Quality of Life Sports and Recreation. Professional Sports Teams. New Orleans Saints - National Football League; New Orleans Hornets ...

UK PubMed Central (United Kingdom)

Neuroleptic malignant syndrome is a life-threatening reaction of neuroleptic medication. The estimated incidence rate of neuroleptic malignant syndrome is between 1% and 1.5% of patients treated with...Full Text Available

Science.gov (United States)

Southam, G., Rothschild, L. & Westall, F. (2007). The geology and habitability of terrestrial planets: fundamental requirements for life.. In: K.E. Fishbaugh, P. ...

Wastenet

Author: METCALFE, J.P., BALDWIN, D.J. and CRAYFORD, J.A. (2000). Summary: Project Report. ENVIRONMENT AGENCY. (Submitted).

UK PubMed Central (United Kingdom)

This Memorandum, after summarizing the life cycle of the different species of human schistosome, reviews the present knowledge of the immunology of schistosomiasis. Each stage of the parasite contains...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This presentation details how wind turbine gearboxes fail to meet 20-year design life and how the Gearbox Reliability Collaborative (GRC) is addressing the challenges.

Energy Technology Data Exchange (ETDEWEB)

To predict the fatigue life of fiber reinforced composites, fatigue process of CFRP laminates of [0 /90 ]{sub s} is investigated and the influence of damages occurring at fiber, matrix and fiber/matrix interface on the various critical strengths and the relationship between residual critical strength and failure are discussed. As a result, it was shown that fatigue strength (i.e. fatigue life) consisted of residual critical strength and stresses occurring at each layer (0 and 90 layers) and interlayer. Moreover, the fatigue failure occurred because the residual critical strength of each layer and interlayer decreased with dependence of their microdamage densities, so that the fatigue life can be predicted by evaluating microdamage behavior in fatigue process. (orig.) 14 refs.

UK PubMed Central (United Kingdom)

BackgroundSenescence is integral to the flowering plant life-cycle. Senescence-like processes occur also in non-angiosperm land plants, algae and photosynthetic prokaryotes. Increasing...Full Text Available

Science.gov (United States)

The dynamic response characteristics of the VAWT rotor are important factors governing the safety and fatique life of VAWT systems. The principal problems are ...

CERN Document Server

The necessity of supporting more and more social interaction (and not only the mere information sharing) in online environments is the disruptive force upon which phenomena ascribed to the Web2.0 paradigm continuously bud. People interacting in online socio-technical environments mould technology on their needs, seamlessly integrating it into their everyday life. MUVEs (Multi User Virtual Environments) are no exception and, in several cases, represent the new frontier in this field. In this work we analyze if and how MUVEs can be considered a mean for augmenting communities (and more in general people) life. We trace a framework of analysis based on four main observations, and through these lenses we look at Second Life and at several projects we are currently developing in that synthetic world.

British Library Electronic Table of Contents (United Kingdom)

Recent improvements in cell purification and transplantation techniques have contributed to the identification of cell populations known as tumor-initiating cells (TIC). This discovery has led to the -cancer stem cell hierarchy- concept, which holds that tumors are organized as a hierarchy of malignant tissues sustained by such TIC. However, this concept remains controversial. In this review, we examine recent advances in cancer stem cell research that have been generated from studies of Philadelphia (Ph) chromosome-positive leukemia. The abnormal Ph chromosome, which arises from a translocation creating the BCR-ABL1 fusion gene, is most commonly associated with chronic myelogenous leukemia (CML) and precursor B cell acute lymphoblastic leukemia (B-ALL). Examination of the pathophysiology ...

Energy Technology Data Exchange (ETDEWEB)

Nd{sub 40}Fe{sub 30}Al{sub 10}Co{sub 15}B{sub 5} alloys were fabricated by high energy ball milling method under various conditions. Microstructure of the alloys was investigated by X-ray diffraction and electron microscopy techniques. Magnetic properties were characterized by hysteresis and thermomagnetic measurements. The high coercive fields up to 2.36 T have been observed on the samples consisting of Nd{sub 2}(Fe,Co,Al){sub 14}B, Nd{sub 6}(Fe,Co,Al){sub 14} and Nd crystallites imbedded in a residual amorphous matrix.

International Nuclear Information System (INIS)

Excited states in the T_z=(1/2) nucleus "8"5Mo have been observed for the first time with the reaction "5"8Ni("3"2S,#alpha#n#gamma#) at 105 MeV. #gamma#-ray transitions in this nucleus have been assigned unambiguously by combining the information from the GASP #gamma#-ray array, the ISIS silicon ball, and the n-Ring neutron detector. Two band structures have been observed in this nucleus; they continue the smooth evolution of the known bands from the lighter N=43 isotones and have been tentatively assigned spins and parity on this basis. After reaching a maximum of collectivity at "8"3Zr, the trend with increasing mass is reversed, showing a smaller collectivity at "8"5Mo. The rotational behavior of the observed bands is discussed on the basis of the projected shell model calculations.

Science.gov (United States)

A six-axis active vibration isolation system (AVIS) is designed by using the direct driven guide and ball contact mechanisms in order to have no cross-coupling between actuators. The point contact configuration gives an advantage of having an easy assembly of eight voice coil actuators to an upper and a base plate. A voice coil actuator is used since it can provide a large displacement and sufficient bandwidth required for vibration control. The AVIS is controlled considering the effect of flexible vibration mode in the upper plate and velocity sensor dynamics. A loop shaping technique and phase margin condition are applied to design a vibration controller. The performances of the AVIS are investigated in the frequency domain and finally validated by comparing with the passive isolation system. The scanning profiles of the specimen are compared together by using the atomic force microscope. The robustness of the AVIS is verified by showing the impulse response. ...

British Library Electronic Table of Contents (United Kingdom)

Superalloys, such as Inconels and Incoloys, are extensively used where high strength is a requirement. However, where these materials are required to slide against one another, particularly with poor or no lubrication, high friction levels and seizure are commonly seen to occur, which can cause component failure. In this work seizure characteristics of three superalloys (Inconel 718 and Incoloys 945 and 945X) were investigated, uncoated, coated with Armoloy (a hard, thin, dense chrome coating with a micro-nodular surface texture) and plasma nitrided in dry sliding conditions. A rig purpose built for initiating seizure was used. It involves sliding a ball against a disc at constant speed while the load is increased. Tests are designed to last less than one rotation so that the wear scar can...

Energy Technology Data Exchange (ETDEWEB)

Several materials, lenses, dry bearings and cables were exposed to a tritiated moisture environment to study the behavior of tritium contamination on candidate materials for ITER remote handling equipment. To optimize the tritium removal procedure, decontamination experiments using a gas purge with three different moisture concentrations were also performed. The surface tritium concentrations of CeO{sub 2} containing alkaline barium glass (NB), CeO{sub 2} containing lead glass (LX) and synthetic quartz (Quartz) after the exposure experiments were 7.80, 10.94 and 0.67 Bq/cm{sup 2}, respectively. It was found that the tritium concentration was influenced by the compositions of the materials. The concentrations of tritium on type 831 (solid lubrication material: graphite) and type 237 (solid lubrication material: tungsten disulfate) dry bearings after the exposure experiments were 89.80 and 31.78 Bq/cm{sup 2}, respectively. The tritium ...

Energy Technology Data Exchange (ETDEWEB)

Apart from the vulnerability implied by the START II treaty, it will bear the burden of the general political opposition to the Yeltsin administration. START II will be seen as part of an overall Yeltsin-Andrei Kozyrev foreign policy that is under fire for selling out Russian national interests in Yugoslavia, the Persian Gulf, and elsewhere. This article discusses public opinion concerning START II, the cost of its implementation, and the general purpose of the treaty.

International Nuclear Information System (INIS)

Paper estimates the corrosion resistance and studies the character of dissolving of silicon-bearing austenite stainless steels in strongly oxidizing media containing phosphate and fluoride admixtures. Corrosion behaviour of the studied steels is determined to depend essentially on the content of admixture or alloying silicon, as well as, on their phase composition in many respects determined by the thermal treatment condition. Refs. 22, figs. 1, tabs. 2.

Energy Technology Data Exchange (ETDEWEB)

The Minami-Iwaki trunk line now under construction by Tokyo Electric Power Company is an UHV transmission line which covers 130km from the central region of the Abukuma highlands, Fukushima Prefecture, through the northern ridge of the Kanto Plain to Imaichi City, Tochigi Prefecture and has 235 steel towers. About 30% of the ground along the above route is mainly layers of sand and gravel. Accordingly it has become urgent to design rationally the pile foundations in the sand and gravel layers. Hence the company has studied an estimation method of the ultimate bearing power of cast-in-place piles penetrating the sand and gravel layers and the displacement of pile heads. In this report, the result of the above study is described. The company has so far used the equations in accordance to the Meyerhof equations for the estimations of the ultimate bearing power and this time, this equations have been examined for its application to the sand and ...

Energy Technology Data Exchange (ETDEWEB)

The development of electric cars always met with the difficulty in storing energy and in recovering it in the form of electric power. Research work done for the last two decades in the field of materials and of new technologies oriented mainly towards aeronautical and space applications have led to designing, realizing and experimenting with flywheels rotating at high speed in magnetic bearings. The results obtained represent openings that, now, fall in with different industrial fields and in particular with application to electric cars.

Energy Technology Data Exchange (ETDEWEB)

It is the purpose of this review to draw together the recent research adding to our understanding of the molecular nature of Clostridia. The thrust here is to emphasize those research advances in biochemistry and genetics that bear upon future development of fermentation processes employing the Clostridia. 222 refs., 10 figs., 5 tabs.

Energy Technology Data Exchange (ETDEWEB)

A total of nine papers were presented at the course with the following titles: peat accumulation and coal basins; coal composition; coal quality; sedimentary environments of coal; generation, storage and migration of natural gas in coal bed reservoirs; geophysical log interpretation; the Ardley coal zone of central Alberta; stratigraphy and sedimentary environment of the Coalspur Formation; and the coal-bearing Luscar Group of western Alberta. All of these papers have been abstracted separately.

Energy Technology Data Exchange (ETDEWEB)

A model has been developed to predict the chemical composition of lakes that form in pyrite-bearing open-pit mines. Pyrite oxidation in wall rock releases sulfuric acid and metals, which mix with ground waters in the lake. Aqueous metal concentrations are calculated using MINTEQA2.

Energy Technology Data Exchange (ETDEWEB)

This report contains preconceptual designs and planning level life-cycle cost estimates for managing hazardous waste. The report`s information on treatment, storage, and disposal modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the US Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report.

International Nuclear Information System (INIS)

Various diagnostics techniques for condition monitoring and life prediction of fluid power components and system are discussed. Though some of the techniques are very promising but may not be accepted because of increase in the instrumentation, it is planned to implement these techniques on various circuits of Fluid Power Lab for further improving and developing these for direct implementation in various fluid power circuits of power reactors. (author). 6 figs.

Energy Technology Data Exchange (ETDEWEB)

Giving many examples, the contribution shows how pump operators may influence the life, efficiency and overall cost of their pumps. Further, it is shown that both the detection of unfavourable or non-optimal operating conditions and the identification of causes necessitate extensive knowledge and experience. (orig.)