Energy Technology Data Exchange (ETDEWEB)

Some of well known F{sub 2} layer anomalies might have their origin in lower atmosphere and some have extra terrestrial sources. It has been suggested that the phenomena occurring below the ionosphere such as thunderstorms, lightning/sprites, volcanic eruptions and earthquakes and above the phenomena like corona mass ejection, solar flares and extra terrestrial events may produce F{sub 2} layer signatures. In the present paper we have tried to summarize the effect of some phenomena occurring below the ionosphere like thunderstorms, lightning/sprites and seismic activity and the phenomena such as solar flares which occur above the ionosphere, on the ionospheric electron and ion temperatures. The paper also discusses possibilities. The ionospheric electron and ion temperatures were measured by the RrPAa payload aboard the Iindian SRrOSS-C2 satellite. The normal day's ion and electron temperatures have been compared to the temperatures recorded during the disturbed day. The ...

International Nuclear Information System (INIS)

Hydrology and hydrogeochemical are auxiliary techniques to valid conceptual hydrogeology an recharge models. Stable isotopes from water trace sources and path flow and Tritium indicates age. This paper is about the use of D 18, D2H y 3H to study the aquifer system on Bajo Cauca antioqueno.

Science.gov (United States)

Experimental investigation of the length of single burning jets of methane and hydrogen previously diluted with an inert gas (nitrogen or helium) was carried out. Efflux of fuel gases into the atmosphere occurred through cylindrical extension pieces 4 and 8 mm in diameter. The Reynolds numbers at the cut of a piece varied in the range from 400 to 12,000. A clearly defined dependence of the jet length on the quality of the added inert gas is obtained. The correlation of experimental data made it possible to recommend formulas for engineering calculations of free laminar and turbulent jets.

Science.gov (United States)

... Briefly, a standard detonator (normally the Scale 1 Gap Test Donor, comprising an exploding bridgewire to initiate a low density PETN pellet and ...

Energy Technology Data Exchange (ETDEWEB)

The behaviour of bare aluminium is studied in atmospheric exposure at 11 natural testing stations with salinity levels ranging between 2.1 and 684 mg Cl''- m''-2 d''-1. In atmospheres of low or moderate aggressivity aluminium behaves as a passive material, though the insignificant corrosion that is produced is sufficient to spoil its appearance. In contrast, at salinity levels of 50 mg Cl''- m''-2 ''-1 or above, aluminium is susceptible to pitting corrosion even in the first year of atmospheric exposure, or in the second year at salinities of {<=} 10 mg Cl''- m''-2 d''-1. For comparative purposes, results are included for aluminium protected with an anodic film of 28 {mu}m thickness exposed at the same testing stations. A 28 {mu}m anodic film, correctly sealed, prevents the risk of localised corrosion even in the most ...

UK PubMed Central (United Kingdom)

Dimethyl sulfoxide (DMSO) is commonly used in biological studies to dissolve drugs and enzyme inhibitors with low solubility. While DMSO is generally thought of as being relatively inert, it...Full Text Available

Science.gov (United States)

The applicability of isothermal solidification as a contacting method for solar cells was proved for the systems AgSn and AuIn. The process is advantageous in that it requires no fluxes, no inert gases, and no pretreatment of the components. The IE contac...

International Nuclear Information System (INIS)

One of the major concerns during high speed welding of magnesium alloys is the presence of porosity in the weld metal that can deteriorate mechanical properties. This study seeks to analyze the presence method and quantity of pore during hybrid laser-tungsten inert gas arc (TIG) welding of magnesium alloy AZ31B by radiography, optical microscopy and electron probe microanalysis (EMPA). At the same time, it identifies both the mechanism of pore formation and a remedy for this problem. The experimental results indicate that lacking of shielding gas for laser beam is the dominant cause of macroporosity formation during the hybrid of laser-TIG welding of magnesium Alloys AZ31B plate, and hydrogen is not main cause to form large pores. A favorable weld without porosity can be obtained by appending lateral shielding gas for laser beam.

International Nuclear Information System (INIS)

Most diffusion phenomena in solids can be understood (or sometimes misunderstood) on a purely classical model. For light interstitials (hydrogen isotopes, the positive muon, and potentially He) there may be anomalous temperature dependences, and isotope effects, and anomalous response to electric fields and temperature gradients. Some of these anomalies are quantal in origin, and will be discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

An industrial EB processing line is started to produce cement-bound /CB/ chipboard with radiation cured acrylic coating. The basic features of this line are presented here. The main technological parameters of coating such as: effect of oligomer- and monomer reactivity, monomer functionality, dose-rate and inerting atmosphere on the progress of curing have been discussed. The EB processed CB board is an advanced composite material for the modern lightweight architecture.

International Nuclear Information System (INIS)

A series of cation exchange membranes was produced by impregnating and coating both sides of a quartz web with a Nafion solution (1100 EW, 10%wt in water). Inert filler particles (SiO_2, ZrO_2 or TiO_2; 5-20%wt) were incorporated into the aqueous Nafion solution to produce robust, composite membranes. Ion-exchange capacity/equivalent weight, water take-up, thickness change on hydration and ionic and electrical conductivity were measured in 1 mol dm"-"3 sulfuric acid at 298 K. The TiO_2 filler significantly impacted on these properties, producing higher water take-up and increased conductivity. Such membranes may be beneficial for proton exchange membrane (PEM) fuel cell operation at low humidification. The PEM fuel cell performance of the composite membranes containing SiO_2 fillers was examined in a Ballard Mark 5E unit cell. While the use of composite membranes offers a cost reduction, the unit cell performance was reduced, in practice, due to drying of the ...

British Library Electronic Table of Contents (United Kingdom)

Background When assessing the function of the cardiovascular system, cardiac output (CO) is a substantial parameter. For its determination, numerous non-invasive techniques have been proposed in the recent years including inert gas rebreathing (IGR) and impedance cardiography (ICG). The aim of our study was to evaluate whether a novel ICG algorithm (electrical velocimetry) and IGR can be used interchangeably in the clinical setting. Methods A total of 120 consecutive stable patients were included resulting in two pairs of repeated non-invasive cardiac output measurements. Results The mean CO was 5.0???1.2?l/min (range 2.6?8.6?l/min) using IGR and 4.4???1.1?l/min (1.7?7.4?l/min) using ICG, respectively. Bland?Altman analysis revealed an acceptable agreement with a mean bias of 0.6???1.2?l/m...

Energy Technology Data Exchange (ETDEWEB)

Drastic changes in waste management procedures are expected from the German Municipal Waste Disposal Regulations which became effective on June 1, 1993. Waste disposal will be subject to certain restrictions which, e.g. demand that wastes must be pretreated and inerted before they are stored. These regulations favor thermal waste disposal methods such as the carbonization/combustion method which is planned for a commercial-scale plant in the city of Fuerth. (orig./BBR)

Energy Technology Data Exchange (ETDEWEB)

By its very nature redox potential measurement is suitable for determining the concentration ratio of a stable redox pair through its interaction with a chemically inert electrode surface but not the absolute concentration of a material. The measured redox potentials agree only rarely with those which are easily calculable theoretically. No individual defined stable redox pair is available in power station water. It is therefore not simply possible to measure definable mixed potentials more precisely. For these reasons redox potential measurement in the power station, as also with other types of water, can no longer be regarded as an indicator, by which it can be established whether oxidizing or reducing materials predominate in the water.

Energy Technology Data Exchange (ETDEWEB)

In situ Auger sputter depth profiles of saturation implants of 3 keV N/sub 2//sup +/ in silicon at room temperature exhibit a sharp peak in the nitrogen concentration in the outermost layers, followed by a monotonic decrease. No broad plateau was observed. The energy of the Auger line corresponding to the Si(2p) core electron excitation, monitored throughout the profiling, exhibits a chemical shift of up to 7 eV at the surface peak concentration. Inert gas ion post-bombardment of unsaturated implants significantly modifies the profile, and supports the suggestion that the surface peak arises through radiation enhanced diffusion of implanted atoms.

Energy Technology Data Exchange (ETDEWEB)

In the context of the shock-initiation problem, we study analytically the first effects of chemistry, treating a small chemical heat release as a perturbation on an inert flow. Specifically, we study the initial transient in plane-shock initiation in a dilute explosive, where the chemical energy is small relative to the mechanical-thermal energy. The vehicle for the study is the mathematical analog for reactive flow. The solution resembles a double refraction: to first order, the pressure or density is a superposition of two forward-going waves, both originating at the rear boundary, and carrying the same function, but running at different velocities. Surprisingly, this first-order solution is independent of the sensitivity of the reaction rate to the state, which appears only at second order.

Energy Technology Data Exchange (ETDEWEB)

This paper presents an analysis of the performance of a selective emitter using small particles of rare earth compounds stable at high temperatures in a low emittance inert gas stream. An expression for the spectral emissive power excluding radiation scattering was derived to include the radiation in the emission band, produced by electronic transitions of the rare earth ion, and the continuum radiation outside the emission band produced by the rare earth host. Preliminary results suggest that a selective emitter based on suspended rare earth oxide particles will have high efficiency and merits further experimental investigation. {copyright} {ital 1996 American Institute of Physics.}

International Nuclear Information System (INIS)

Fully fluorinated compounds (perfluoro compounds) represent a class of chemicals which include many extremely inert species-inert to both chemical reaction and photodissociation. Well known examples include SF6 and the perfluorocarbons (PFCs) CF_4 and Teflon. SF_6 is used industrially in electrical switch gear and as an atmospheric tracer. CF_4 and C_2F_6 are released into the atmosphere as a by-product of aluminum manufacture. Several perfluoro compounds have been proposed as substitutes for the ozone-destroying Freons and halons; proposed substitutes include SF_6, c-C_4F_8, C_5F_1_2, and C_6F_1_4. These chemicals were chosen in part because they do not harm the stratospheric ozone layer and were therefore considered environmentally friendly. Recently, Ravishankara et al. reported that perfluoro compounds have significant global warming potential (GWP), contributing to the greenhouse effect due to strong infrared absorption. The perfluoro ...

International Nuclear Information System (INIS)

Zirconium is a transition element located along with sister elements titanium and hafnium in Group IVB of the periodic table. It is grayish white metal, with a density somewhat less than carbon steel. Zirconium is the ninth most common metallic element in the earth's crust, and is more abundant than zinc, lead, nickel, or even copper. Zirconium is exceptionally resistant to corrosion by many common acids and alkalis. It is resistant to most organic acids, such as formic, acetic, lactic, and oxalic acids. It also has a high resistance to localized forms of corrosion, such as pitting, crevice corrosion, and stress corrosion cracking. Its corrosion resistance is caused by the formation of a dense, tenaciously adherent, chemically inert oxide film on the surface. This oxide film protects the base metal from both chemical and mechanical attack at temperatures up to about 400 C (750 F). This article describes zirconium's formability, machinability, corrosion resistance, ...

Energy Technology Data Exchange (ETDEWEB)

As the ground state potential curve is strongly related to spectral line shapes, the minumum position of the ground state potential is obtained from the experiemental absorption profile k({delta}{nu}, T) at high density of the radiating atoms. The temperature dependence of the absorption processes of Hg and Cd lines 253.65 and 326.1 nm, respectively perturbed by inert gases (Xe, Kr, Ar and Ne) had been carefully studied over a wide spectral range. Using the point of the maximum temperature dependence {delta}{nu} {sub m} in each case, we are able to calculate the position of the ground state potential R {sub m} using a simple formula.

International Nuclear Information System (INIS)

Test Blanket Modules (TBM) will be tested in ITER to verify the capability of tritium breeding and recovery and the extraction of thermal energy suitable for the production of electricity. A Helium Cooled Solid Breeder (HCSB) TBM has been developed in Korea to accomplish these goals. Reduced Activation Ferritic/Martensitic (RAFM) steel has been chosen as the primary candidate structural material for Korean TBM. Due to the complexity of the First wall (FW) and Side wall (SW), it is necessary to develop various joining technologies, such as Hot Isostatic Pressing (HIP), Electron Beam Welding (EBW) and Tungsten Inert Gas (TIG) welding, for the successful fabrication of TBM. In this study, the mechanical properties of TIG welded RAFM steel were investigated. Various mechanical tests of TIG-welded RAFM steel were performed to obtain the optimized TIG welding process for RAFM steel

Energy Technology Data Exchange (ETDEWEB)

Carbon films have been made by a variety of techniques, including evaporation, sputtering, and laser or thermal pyrolysis of organic polymers. Polyacrylonitrile (PAN) is often used as a carbon precursor, since low-temperature thermo-oxidative pretreatment produces a material which can be pyrolyzed without loss of shape. This is the basis for the production of carbon fibers with good mechanical properties. We report here the formation of very thin films of carbon (500 to 1500 A) by pyrolysis of spin-cast PAN. Using this technique, large, conductive films can be made which are sufficiently robust to allow intact lift-off and transfer of the films from one substrate to another. Such films are chemically inert, but can be photolithographically patterned and etched with an oxygen plasma.

International Nuclear Information System (INIS)

The solubility of Sn(IV) oxide was determined in a dilute NaClO_4 solution with pH 2 through 12 at ambient temperature. Both oversaturation and undersaturation experiments were carried out in an inert gas glovebox where the concentration of the oxygen and carbon dioxide were less than 1 ppm. The solubility of Sn(IV) oxide was 3 x 10"-"8 mol/l at neutral pH, and increased at pH > 7.5. Equilibrium constants of soluble reactions were calculated from the experimental data, using curve fitting method. The study suggests that the solubility of Sn(IV) oxide would be higher than that provisionally used in current safety assessments of HLW disposal sites.

Energy Technology Data Exchange (ETDEWEB)

A method for determining the mobility of hydrogen as a function of temperature in superconducting niobium cavities comprising: 1) heating a cavity under test to remove free hydrogen; 2) introducing hydrogen-3 gas into the cavity; 3) cooling the cavity to allow absorption of hydrogen-3; and 4) measuring the amount of hydrogen-3 by: a) cooling the cavity to about 4.degree. K while flowing a known and regulated amount of inert carrier gas such as argon or helium into the cavity; b) allowing the cavity to warm at a stable rate from 4.degree. K to room temperature as it leaves the chamber; and c) directing the exit gas to an ion chamber radiation detector.

Energy Technology Data Exchange (ETDEWEB)

Inert markers (evaporated tungsten and silver) were used in growth studies of silicides formed both by thermal annealing and by ion mixing in the Ni/Si, Pd/Si, and Cr/Si systems. The markers were initially imbedded inside silicides and backscattering spectrometry was used to determine the marker displacement after different processing conditions. The results obtained in thermal annealing are quite consistent with that found in previous investigations. Ni is the dominant diffusing species in Ni/sub 2/Si, while Si is the diffusing species in CrSi/sub 2/. In Pd/sub 2/Si, both Pd and Si are moving species with Pd the faster of the two. In contrast, in growth of silicides by ion irradiation Si is the faster diffusing species in all three systems.

Energy Technology Data Exchange (ETDEWEB)

Sintered glass-ceramics have been produced using municipal incinerator solid residues and glass cullet or an inert waste, from feldspars processing, as sintering aids. The capability of three different mixtures, either previously vitrified or not, to be sintered was investigated by means of linear shrinkage, water absorption and bulk density measurements, and by X-ray diffraction analysis and scanning electron microscopy observations. Particular attention has been addressed to the study of particle size effect on the sintering process. The conclusions that can be drawn from the experimental study are that the preliminary vitrification step is essential in order to obtain a dense sintered glass-ceramic product in the 850-1050 C temperature range developing silicate crystalline phases. The optimal powder particle size that confers a good densification degree was found to be < 45 {mu}m. (orig.)

British Library Electronic Table of Contents (United Kingdom)

White seabream (Diplodus sargus) is today recognized as a potential species for Mediterranean aquaculture. Still, scarce information exists on weaning practices in order to reduce the live food period. This study aims to evaluate the effect of an early weaning on fish larvae digestive enzymes activities. In order to accomplish this, larvae were weaned with an inert diet at 20days after hatching (DAH) (feeding regime W20) and a control group was weaned at 27DAH (feeding regime W27). Before weaning, the onset and development of the main digestive enzymes were studied. The pattern of variation of digestive enzymes activities were analyzed at 0, 2, 9, 13 and 20DAH, and from then on at 0, 1 and 3weeks after diet introduction; that is, at 20, 27 and 41days for feeding regime W20, and days 27, 34...

CERN Document Server

We consider a minimal model of GUT scalar dark matter (DM) stabilized by the discrete gauge matter parity $P_{X}$ that arises from breaking of $SO(10)$. The dark sector comprises the complex singlet $S$ and the inert doublet $H_{2}$. GUT scale parameters are evaluated to the electroweak scale via Renormalization Group Equations (RGEs). Experimental and theoretical constraints limit the DM mass to the 80 GeV to 2 TeV range. The EW symmetry breaking is radiative and can occur via RGE running and 1-loop matching corrections from integrating out DM. Because the next-to-lightest scalar is almost degenerate with DM, it gives a background free displaced decay vertex at the LHC.

International Nuclear Information System (INIS)

Ionizing radiations that differ in number, size, and distribution of energy deposition events might be expected to cause different effects for the same absorbed dose. Furthermore, microdosimetry calculations suggest that large variations in biological effectiveness might be expected for internally deposited alpha-emitting radionuclides for the same absorbed dose, depending upon the specific activity and spatial distribution of the sources in tissue. The study described in this article was designed to demonstrate these phenomena in vitro. Cultured Chinese hamster ovary (CHO-K1 BH4) cells were exposed in vitro to inert, insoluble ceramic microspheres in zirconium dioxide labeled with "2"3"9Pu. The average exit energy of the 5.15 MeV alpha particle was calculated to be 4.3 MeV. Exposure times varied from four to seven hours to achieve the desired dose level.

Energy Technology Data Exchange (ETDEWEB)

This report describes the progress of the Dutch RAS programme on `Recycling and Transmutation of Actinides and Fission Products` over the year 1995, which is the second year of the 4-year programme 1994-1997. An extensive listing of reports and publications from 1991 to 1995 is given. Highlights in 1995 were: -The completion of the European Strategy Study on Nuclear Waste Transmutation as a result of which the understanding of transmutation of plutonium, minor actinides and long-lived fission products in thermal and fast reactors has been increased significantly. Important ECN contributions were given on Am, {sup 99}Tc and {sup 129}I transmutation options. Follow-up contracts have been obtained for the study of 100% MOX cores and accelerator-based transmutation. - Important progress in the evaluation of CANDU reactors for burning very large amounts of transuranium mixtures in inert matrices. - The first RAS irradiation experiment in the HFR, in which the ...

International Nuclear Information System (INIS)

Immobilization of long-lived fission products (LLFP) such as radioactive Tc, Cs and Sr into #alpha#-SiAlON ceramics was evaluated using stable isotopes instead of radioactive isotopes, and the applicability of #alpha#-SiAlON ceramics as the inert matrix for transmutation of LLFP was investigated. In the case of single addition of SrO, SrCO_3, Cs_2CO_3 or ReO_2 to the starting materials, #alpha#-SiAlON, single phase was not formed after hot-pressing. When Y_2O_3 was added with SrO, SrCO_3 or Cs_2CO_3 to the starting materials (#alpha#-Si_3N_4, AlN and #alpha#-Al_2O_3) in optimum compositions, #alpha#-SiAlON single phase was obtained after hot-pressing at 1700degC or 1800degC. From the EDS analysis, Sr and Y were detected from grains. It is suggested that Y would assist the expansion of interstices of #alpha#-SiAlON lattice, resulting in the incorporation of Sr"2"+ into #alpha#-SiAlON lattice. In the case of Cs addition with Y, Cs was not incorporated into ...

Energy Technology Data Exchange (ETDEWEB)

Austenitic stainless steels have been implanted with molybdenum ions (Mo[sup +], 100 keV, 2.5 x 10[sup 16] atoms cm[sup -2]). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of [approx] 1000 A with a maximum molybdenum concentration of [approx] 9 at.% Mo located at [approx] 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H[sub 2]SO[sub 4] have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer ...

International Nuclear Information System (INIS)

The classical theory of collisional broadening and shift parameters (?, ?) of an isolated spectral line was used to obtain simple analytical formulas for calculating both ? and ?. These formulas were obtained on the assumption that the short range interaction is effective only in the broadening while the long range is effective in the shift of the spectral line. These parameters ? and ? depend on the limiting phase shifts responsible for broadening ?b and shift ??. It was found that the values of ?b and ?? are not equal to each other as was proposed by Weisskopf ?b=??=1. The maximum and average values of ?b (?bmax, ?bav) and ?? (??max, ??av) were obtained by numerical evaluation, using different inverse power potentials. By introducing these parameters into the approximated formulas for ? and ? using Van der Waals and Lennard-Jones potential, it was found that the results of calculations for (? and ?) with different atomic transitions perturbed by different inert ...

Energy Technology Data Exchange (ETDEWEB)

NMR and CD studies indicate that Mg/sup 2 +/ and Ca/sup 2 +/ are able to change the conformation of tetracycline in DMSO solution. This may affect the in vivo effect of tetracycline. Using /sup 23/Na NMR, the formation constant of NaLAS (LAS represents the anion of lasalocid A) was found to be 80 M/sup -1/ which is much smaller than that in less polar solvents. Spin-lattice relaxation measurements were made to study the binding sites of Gd/sup 3 +/ on Las in ChCl/sub 3/-DMF mixed solvent system. No intermediate conformation (between cyclic and open-chain) was found. LAS was found to be a good second-sphere ligand to inert transition-metal amines. NMR studies suggest that LAS is in cyclic conformation when bound to these metal amines. A new method for the synthesis of spin-labeled anticancer Pt(II) complexes was developed. It is very simple and gives high yield of pure spin-labeled Pt(II) complexes.

International Nuclear Information System (INIS)

A process is described for the selective oxidation of ammonia to nitric oxide in about 90% or greater yield with a minimum of nitrogen or dinitrogen oxide (N/sub 2/O) as by-products, comprising: (1) contacting gaseous ammonia in an oxygen containing gas optionally with an inert gaseous diluent with a mixed metal perovskite catalyst of the general formula: ABO/sub 3/, wherein: A is selected from the alkali, alkaline earth, lanthanide, or actinide metals or a mixture of these metals having a relatively large ionic, radius, and B is selected from an element or a combination of elements selected from Groups IB, IVB, VB, VIB, VIIB, or VIII of the Periodic Table, wherein the perovskite phase of the catalyst has an equilibrium partial pressure of oxygen at 1000"0C of greater than about 10/sup -15/ bar; and (2) heating the reactants of step (1) at greater than about 500"0C under conditions of 10 to 100,000 hr/sup -1/ hourly space velocity.

International Nuclear Information System (INIS)

Marker experiments for studying the mass transport through a palladium silicide layer on a crystalline substrate during thermal oxidation at 700 to 850 deg C have been reported recently. In this work argon gas embedded in amorphous silicon during sputtering was implemented as the inert marker and the oxidation of PdSi was processed above 900 deg C. At this high-temperature oxidation silicon-rich silicide PdSisub(y), with y exceeding 5, may be obtained. This can be anticipated by considering the Pd-Si phase diagram which shows the liquid phase may appear at an annealing temperature above 892 deg C. As a result, a non-stoichiometric and non-uniform silicide layer may develop at the sample surface. Marker analysis showed that both palladium and silicon dissociated at the Pdsub(x)Si/ SiO_2 interface and moved to the substrate with the silicon being the dominant diffuser. The Rutherford backscattering spectra (RBS) showing the oxide film and composition isothermally ...

Energy Technology Data Exchange (ETDEWEB)

Quantitative estimates of lung cancer risk from exposure to diesel engine emissions were developed using data from three chronic bioassays with Fischer 344 rats. Human target organ dose was estimated with the aid of a comprehensive dosimetry model. This model accounted for rat-human differences in deposition efficiency, normal particle clearance rates, transport of particles to lung-associated lymph nodes, respiration rates, and lung surface area, as well as high-dose inhibition of particle clearance. Recent evidence indicates that the inert carbon core of the diesel particulate matter is likely to be the primary source of carcinogenicity. The epithelial tissue lining the alveoli and lower airways is the primary target site for induction of lung tumors. Dose was therefore based upon the concentration of carbon particulate matter per unit lung surface area. Unit risk estimates were developed using either a time-to-tumor or a linearized multistage model. The unit ...

Energy Technology Data Exchange (ETDEWEB)

Our goal was a process to convert methane to higher hydrocarbons oxidatively, since this circumvents thermodynamic yield limits of a strictly degydrogenative process. Keller and Bhasin converted thermodynamic yield limits of a strictly dehydrogenative process. Keller and Bhasin converted methane to higher hydrocarbons by using metal oxides as oxidants, without co-fed oxygen. They stated that selectivity is necessarily poor if gaseous oxygen is present. Jones and Sofranko have also used reducible metal oxides as oxidants in a group of their parents, but later used some of those materials with continuous O{sub 2} feed without much loss of selectivity. Baerns, Lunsford and Otsuka have shown that high selectivity could be possible with co-fed O{sub 2} at least for low O{sub 2} partial pressures, over PbO-A1{sub 2}O{sub 3}, Li-MgO and rare earths. The performance of a group of multicomponent oxide catalysts, containing lead and magnesium oxides, for oxidative conversion of methane to higher ...

Energy Technology Data Exchange (ETDEWEB)

The excellent high temperature strength and thermal conductivity of molybdenum-base alloys provide attractive features for components in advanced magnetic and inertial fusion devices. Refractory metal alloys react readily with oxygen and other gases. Oxidized molybdenum in turn is susceptible to losses from volatile molybdenum trioxide species, (MoO3)m, in air and the hydroxide, MoO2(OH)2, formed from water vapor. Transport of radioactivity by the volatilization, migration, and re-deposition of these volatile species during a potential accident involving a loss of vacuum or inert environment represents a safety issue. In this report we present experimental results on the oxidation, volatilization and re-deposition of molybdenum from TZM in flowing air between 400 and 800°C. These results are compared with calculations obtained from a vaporization mass transfer model using chemical thermodynamic data for vapor pressures of MoO3(g) over pure solid MoO3 and ...

Energy Technology Data Exchange (ETDEWEB)

On-board reforming of liquid fuels to hydrogen for use in proton exchange membrane (PEM) fuel cell electric vehicles (FCEVs) has been the subject of numerous investigations. In many respects, liquid fuels represent a more attractive method of carrying hydrogen than compressed hydrogen itself, promising greater vehicle range, shorter refilling times, increased safety, and perhaps most importantly, utilization of the current fuel distribution infrastructure. The drawbacks of on-board reformers include their inherent complexity [for example a POX reactor includes: a fuel vaporizer, a reformer, water-gas shift reactors, a preferential oxidation (PROX) unit for CO cleanup, heat exchangers for thermal integration, sensors and controls, etc.], weight, and expense relative to compressed H{sub 2}, as well as degraded fuel cell performance due to the presence of inert gases and impurities in the reformate. Partial oxidation (POX) of automotive fuels is another alternative ...

International Nuclear Information System (INIS)

High resolution Monte-Carlo simulations show that the neutron spectrum, fuel burnup and fuel temperature feedback effect of a PWR core loaded with Thoria-based fuel (Th/Pu-O_2) do not significantly differ from the MOX fuelled one due to the similar neutronic characteristics of both fertile materials (Th-232, U-238). The core physics of this fuel variant is characterized by an enhanced moderator/void temperature coefficient (by factor 2.4) and high incineration rate for Pu (approx. 60 %). A PWR core loaded with the Molybdenum-based inert matrix fuel (IMF) - in contrast to MOX-, shows a harder spectrum, resulting in small temperature coefficients of reactivity and particularly in a higher fuel depletion rate as well as an enhanced TRU reduction performance. The incineration of Pu amounts to 46 % resulting, in turn, in generation of minor actinides of about 10 % of the total Pu consumption. The higher excess reactivity resulting from the initial Pu contents is ...

International Nuclear Information System (INIS)

Recent work has indicated that the suppression of boron transient enhanced diffusion (TED) in carbon-rich Si is caused by nonequilibrium Si point defect concentrations, specifically the undersaturation of Si self-interstitials, that result from the coupled out-diffusion of carbon interstitials via the kick-out and Frank--Turnbull reactions. This study of boron TED reduction in Si_1_-_x_-_yGe_xC_y during 750"oC inert anneals has revealed that the use of an additional reaction that further reduces the Si self-interstitial concentration is necessary to describe accurately the time evolved diffusion behavior of boron. In this article, we present a comprehensive model which includes #left brace#311#right brace# defects, boron-interstitial clusters, a carbon kick-out reaction, a carbon Frank--Turnbull reaction, and a carbon interstitial-carbon substitutional (C_iC_s) pairing reaction that successfully simulates carbon suppression of boron TED at 750"oC for anneal times ...

Energy Technology Data Exchange (ETDEWEB)

A laboratory differential simulation method is used for the design of carbonization columns at coal-tar processing in which phenols are regenerated from phenolate solution by carbon dioxide absorption. The design method is based on integration of local absorption rates of carbon dioxide along the column. The local absorption rates into industrial phenolate mixture are measured in a laboratory model contactor for various compositions of the gas and liquid phases under the conditions that ensure the absorption rates in the laboratory absorber simulate the local rates in the industrial column. On the bases of the calculations, two-step carbonization columns were designed for 30000 t/year of the phenolate solution treatment by carbon dioxide. The absorption proceeds at higher pressure of 500 kPa and temperatures from 50 to 65 C, pure carbon dioxide is used and toluene is added. These conditions have the following favourable effects: (I) significant size reduction of the columns, (ii) it is ...

Energy Technology Data Exchange (ETDEWEB)

The two-dimensional Eulerian hydrodynamic code 2DE with the shock initiation of heterogeneous explosive burn model called Forest Fire, is used to model numerically the interaction of jets of steel, copper, tantalum, aluminum, and water with steel, water, and explosive targets. The calculated and experimental critical condition for propagating detonation may be described by the Held V/sup 2/d expression (jet velocity squared times the jet diameter). In PBX 9502, jets initiate an overdriven detonation smaller than the critical diameter, which either fails or enlarges to greater than the critical diameter while the overdriven detonation decays to the C-J state. In PBX 9404, the jet initiates a detonation that propagates only if it is maintained by the jet for an interval sufficient to establish a stable curved detonation front. The calculated penetration velocities into explosives, initiated by a low-velocity jet, are significantly less than for non-reactive solids of the same density. ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a process for preparing of an ion exchanger, comprising: treating an ionically inert activated charcoal porous support with an aqueous solution of metal oxychloride selected from the group consisting of zirconium and titanium oxychlorides so as to impregnate the pores of the support with the solution; separating the treated support from excess metal oxychloride solution; converting the metal oxychloride to a hydrous metal oxide precipitate in the pores of the support at a pH above 8 and above the pH whereat the hydrous metal oxide and activated charcoal support have opposite zeta potentials and sufficient to hydrolyze the metal oxychloride. It also describes a process for preparing an ion exchanger comprising: treating granulated activated charcoal with a concentrated solution of a metal oxychloride from the group consisting of zirconium and titanium oxychlorides, degassing the mixture; and treating the resultant mixture with a base selected ...

Energy Technology Data Exchange (ETDEWEB)

Oil and gas resources in the offshore areas of the US constitute a significant portion of US recoverable hydrocarbon resources. The exploration, development and production of these offshore resources in California, however, could have significant air quality implications for coastal air basins. This study was developed to address a problem that frequently arises with offshore air quality assessments. Typically, such assessments are performed for a specific activity scenario (e.g., a Federal OCS Lease Sale involving a projected number of drilling rigs, platforms, pipelines, etc.) and assume a projected (but uncertain) level of recoverable oil and gas resources. This study enables interested parties to estimate air emissions and impacts for a wide range of OCS-related development scenarios. The modular emission calculation procedure and the generic impact assessment provide for maximum flexibility in reassessing the emissions and impacts should changes in production scenarios occur. The ...

International Nuclear Information System (INIS)

The nature of the electrolyte strongly influences the electrode kinetics of the oxygen evolution reaction (OER) and electrochemical ozone production (EOP) mainly by affecting the degree of coverage by the intermediates of both processes. The anomalous behaviour of the Tafel coefficient, b, as a function of temperature was attributed to surface adsorption of the electrolyte species, and the competition between them, as well as gas bubble adherence. Comparison of the current efficiencies of the EOP, PHI_E_O_P, determined for different temperatures and supporting electrolyte compositions, showed the presence of fluorinated anions increases PHI_E_O_P. The influence of the anion nature on PHI_E_O_P, when analysed in the light of the proposed electrode mechanism, reveals introduction into the electrolyte of anions having a high electronegativity changes the double layer structure resulting in an increase of surface concentration of the active centres leading to EOP. The inhibition of the OER ...

International Nuclear Information System (INIS)

The weldability and high temperature strength properties of tungsten-inert-gas (TIG) weldments of Hastelloy alloy XR were investigated by using two different heats of filler metals; the first (HXRF1) was designed on the basis of multiple regression analysis; the second (HXRF2) was the reference material. Bend tests, the FISCO cracking test and optical metallography were used to evaluate weldability. Tensile and creep tests were performed at 900deg C to evaluate high temperature strength properties. The results of weldability tests for both alloys showed good performance. The tensile properties of the weldments were remarkably improved in particular with respect to high temperature ductility. The creep rupture strength in the weldments made with alloy-designed HXRF1 was much higher than those of the Hastelloy alloy XR-II base metal with a higher B content. Furthermore, the creep properties were stable with respect to variations in welding conditions. Since the ...

Energy Technology Data Exchange (ETDEWEB)

Theoretical and experimental studies have been carried out on the combustion of azide polymers used as a binder in high-energy propellants. AMMO (3-azidemethyl-3`-methyloxetane) is one of the energetic azide polymers which contain N3 groups in their molecular structures. EDNA (ethylenedinitramine) is a linear nitramine which has modest properties in the flame temperature and the molecular weight of burned gases as compared with HMX (cyclotetramethylenetetranitramine) and NQ (nitroguanidine). In this study, the burning rate characteristics of azide/nitramine propellants were investigated in order to gain a wide spectrum of burning rate. As a result, the burning rate of AMMO/EDNA propellant is higher than that of AMMO/HMX propellant and the pressure exponent of AMMO/EDNA propellant is lower than that of AMMO/HMX propellant. Both AMMO/EDNA and AMMO/HMX propellants exhibited the same combustion wave structure as inert polymer/nitramine propellants. The burning surface ...

Energy Technology Data Exchange (ETDEWEB)

Borohydrides such as LiBH{sub 4} have been studied as candidates for hydrogen storage because of their high hydrogen contents (18.4 wt% for LiBH{sub 4}). Limited success has been made in reducing the dehydrogenation temperature by adding reactants such as metals, metal oxides and metal halides. However, full rehydrogenation has not been realized because of multi-step decomposition processes and the stable intermediate species produced. It is suggested that adding second cation in LiBH{sub 4} may reduce the binding energy of B-H. The second cation may also provide the pathway for full rehydrogenation. In this work, several bimetallic borohydrides were synthesized using wet chemistry, high pressure reactive ball milling and sintering processes. The investigation found that the thermodynamic stability was reduced, but the full rehydrogenation is still a challenge. Although our experiments show the partial reversibility of the bimetallic borohydrides, it was not sustainable during ...

International Nuclear Information System (INIS)

"2"1"1At is one of the most promising radionuclides in #alpha#-radioimmunotherapy (#alpha#-RIT). Unfortunately, biomolecules labeled by direct electrophilic astatination are unstable due to the rapid loss of "2"1"1At under both in vitro and in vivo conditions. The present paper describes the results of our studies on attaching At"- to the rhodium(III) complex with thioether ligand: 1,5,9,13-etrathiacyclohexadecane-3,11-diol (16-S4-diol). Rh"3"+ was chosen as a moderately soft metal cation which should form very strong bonds with soft At"- anions, but first of all because of the kinetic inertness of low spin rhodium(III) d"6 complexes. The 16-S4-diol ligand was selected due to formation of stable complexes with Rh"3"+. The experiments related to optimization of the reaction conditions were performed with the "1"3"1I, basing on a chemical similarity of I"- to At"-. The experiments with "2"1"1At were then carried out under the conditions found optimal for I"-. The ...

Energy Technology Data Exchange (ETDEWEB)

A series of dinuclear platinum(II) complexes, [(dien)Pt(NH{sub 2}(CH{sub 2}){sub n}NH{sub 2})Pt(dien)]Cl{sub 4} (dien = diethylenetriamine, n = 8, 9, 10, and 12) and their corresponding [2]rotaxanes with {alpha}-cyclodextrin ({alpha}-CD), [(dien)Pt{l_brace}NH{sub 2}(CH{sub 2}){sub n}NH{sub 2}{center_dot}{alpha}-CD{r_brace}Pt(dien)]Cl{sub 4}, have been synthesized and characterized by {sup 1}H, {sup 13}C, and {sup 195}Pt NMR spectroscopy and electrospray mass spectrometry. The rotaxanes were prepared by reacting the {l_brace}NH{sub 2}(CH{sub 2}){sub n}NH{sub 2}{center_dot}{alpha}-CD{r_brace} pseudorotaxanes with [Pt(dien)]Cl, to stopper the included linear {alpha},{omega}-diaminoalkane chains with the inert Pt(II) end groups. The kinetics of the self-assembly and dissociation of the {beta}-CD rotaxane, [(dien)Pt{l_brace}NH{sub 2}(CH{sub 2}){sub 10}NH{sub 2}{center_dot}{beta}-CD{r_brace}Pt(dien)]{sup 4+}, were investigated by using {sup 1}H NMR and are indicative of ...

International Nuclear Information System (INIS)

Austenitic stainless steels (304-type) have been implanted with nitrogen ions in order to investigate the effects of implanted nitrogen on their electrochemical behaviour and on the nature of the passive film formed on the steels in acid (0.5M H_2SO_4). Alloys with two nitrogen doses have been prepared (2.5x10"1"6 and 2x10"1"7 N atoms/cm"2). The implanted alloys have been characterized by "1"5N-NRA (nuclear reaction analysis) and XPS (X-ray photoelectron spectroscopy). Alloy surfaces with well-defined N concentrations were prepared, prior to the electrochemical measurements, by argon-ion sputtering of the implanted material for a fixed time in order to reach a well-defined point on the nitrogen depth profile. The samples were then transferred without exposure to air to an electrochemical cell mounted in an inert gas glove box. The implanted nitrogen modifies the electrochemical behaviour of the alloy. The anodic dissolution in the active state is enhanced, and the ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the invention is a process for the production of a particularly finely divided, homogeneous transition metal phosphide and transition metal chalcogenide of Daltonian stochiometry by the conversion of at least one powder transition metal or a transition metal alloy with phosphorus or with a chalcogen at raised temperature, which is characterized by the fact that the conversion is carried out in the presence of at least one inert finely divided auxiliary material which is soluble in water and does not sinter together at the reaction temperature, and that the conversion produce removes the auxiliary material. Even relatively small quantities of the auxiliary material are sufficient to ensure rapid and homogeneous conversion of the reaction partners to the reaction product having a large surface. A ratio of 1 part by volume of a mixture of a transition metal and phosphorus or chalcogen to 1 part by volume of finely divided auxiliary material proved ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes the vapor phase catalytic dehydrogenation of a C/sub 2/-C/sub 4/ paraffin by contacting the paraffin with a spinel of the formula A/sup III/V/sub 2-x//sup III/C/sub x//sup III/O/sub 4/, formula (1) or a crystalline perovskite of the formula D/sup III/V/sub 1-y//sup III/C/sub y//sup III/O/sub 3/, formula (2) where A is one or more of Mg, Zn, Mn, Fe, Co, Ni, Cu and Cd; D is oone of more of Y, the rare earths and Bi; C is one or more of Al, Ga, Cr, Fe and Co, x is zero to < 1.9, and y is zero to < 0.9, which spinel or perovskite is made by a process which comprises (1) reducing a pentavalent vanadium oxidic compound to substantially the V/sup 111/ state by heating at 100/sup 0/C or less an aqueous medium slurry of solution of the pentavalent compound containing a reducing agent selected from hydrazine and a hydrocarbylhydrazine, (2) providing in the aqueous medium ether before, during or after the reducing step, A/sup II/, D/sup III/ and C/sup III/ cations in ...

Energy Technology Data Exchange (ETDEWEB)

This document describes the development testing phase associated with the OTA Shear activity and defines the controls to be in place throughout the testing. The purpose of the OTA Shear Program was to provide equipment that is needed for the processing of 40 foot long, sodium wetted, irradiated core components previously used in the FFTF reactor to monitor fuel and materials tests. There are currently 15 of these OTA test stalks located in the Test Assembly Conditioning Station (TACS) inerted vault. These need to be dispositioned for a shutdown mission to eliminate this highly activated, high dose inventory prior to turnover to the ERC since they must be handled by remote operations. These would also need to be dispositioned for a restart mission to free up the vault they currently reside in. The waste handling and cleaning equipment in the J33M Cell was designed and built for the handling of reactor components up to the standard 12 foot length. This program will ...

Energy Technology Data Exchange (ETDEWEB)

For joining type 316LN austenitic stainless steel to modified 9Cr-1Mo steel for power plant application, a trimetallic configuration using an insert piece (such as alloy 800) of intermediate thermal coefficient of expansion (CTE) has been sometimes suggested for bridging the wide gap in CTE between the two steels. Two joints are thus involved and this paper is concerned with the weld between 316LN and alloy 800. These welds were produced using three types of filler materials: austenitic stainless steels corresponding to 316,16Cr-8Ni-2Mo, and the nickel-base Inconel 182{sup 1}. The weld fusion zones and the interfaces with the base materials were characterised in detail using light and transmission electron microscopy. The 316 and Inconel 182 weld metals solidified dendritically, while the 16-8-2(16%Cr-8%Ni-2%Mo) weld metal showed a predominantly cellular substructure. The Inconel weld metal contained a large number of inclusions when deposited from flux-coated electrodes, but was ...

International Nuclear Information System (INIS)

The transmutation of minor actinides in-reactor is one solution currently being studied for the long time management of nuclear waste. In the heterogeneous concept the radionuclides are incorporating in an inert ceramic matrix. The support material must be insensitive to radiation damage. Fission product damage is the main radiation damage source during the transmutation process and therefore it is of the utmost importance to study their effects. We irradiated spinels MgAl_2O_4 (matrix of reference) and ZnAl_2O_4 by fast ions (by example: (86)Kr of approximately 400 MeV) simulating the fission products. Under these conditions, the damage is primarily due to the electronic energy losses (Se). One of the structural features of spinel AB_2O_4 is that the two cations (A(2+) and B(3+)) can exchange their site. This phenomenon is quantified by the inversion parameter. We highlight by XRD in grazing incidence that the structural changes observed in MgAl_2O_4 correspond to ...

Energy Technology Data Exchange (ETDEWEB)

The corrosion properties of sputtered molybdenum and molybdenum silicide films in hydrochloric acid (HCl) have been studied by means of potentiodynamic measurements. Contributions from the substrate to the corrosion behaviour was avoided by depositing the films on inert aluminium oxide (Al{sub 2}O{sub 3}). The compositions studied were Mo, MoSi{sub 0.58}, MoSi{sub 1.04}, MoSi{sub 1.4} and MoSi{sub 1.9-2.1}. Characterisation of the samples was made by X-ray diffraction (XRD) and scanning electron microscopy (SEM) before and after corrosion. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) were used to analyse the polarised films. Corrosion of Mo{sub 3}Si was found in the molybdenum-rich samples (MoSi{sub 0.58}) containing the two phases Mo{sub 3}Si and Mo{sub 5}Si{sub 3}. Polarisation curves for these films showed one passivation peak at 228 mV vs. the saturated calomel electrode (SCE). The MoSi{sub 1.9-2.1} films had the best corrosion ...

International Nuclear Information System (INIS)

Most countries have taken the vitrification route for managing High Level Waste (HLW). Depending on composition of site-specific HLW, suitable glass forming oxides are added to it in a melting furnace designed for converting the mixture to a matrix of borosilicate glass. After thorough homogenization, the product is poured into stainless steel canisters as an inert solidified form. Canisters are seal welded and 2-3 such containers are then packed and sealed in another bigger container for providing an additional engineered barrier. This product form is considered safe for long-term storage. The concurrent vitrification technologies employ either induction-heated metallic melters or joule-heated direct resistance-heated ceramic melters. In India, both technologies have been adopted. While older facilities in Trombay and Tarapur employ metallic melters, a retrofitted facility at Tarapur and the new plant at Kalpakkam are based on ceramic melter operations. Compared ...

Energy Technology Data Exchange (ETDEWEB)

Major advances in 'Energy and Materials Cycles' have been achieved in the removal of heavy metals from the solid residues of municipal waste incineration. It has been conclusively shown that the oxidation/reduction conditions established during the thermal treatment of filter ash have a decisive influence on the evaporation of groups of heavy metals. With respect to biomass gasification, studies have been carried out with respect to the best way of extracting pure hydrogen from the low calorific value gas that is typically obtained from a biomass gasifier. The overarching goal of the laboratory 'High Temperature Solar Technology' is the use of solar energy for the production of solar fuels, or for the reduction of CO{sub 2} emissions in large scale industrial processes that are conventionally carried out with the use of fossil fuels. In a short-term project targeted at the solar production of lime, highly encouraging results (98% degree of ...