Comparison of Suture-Based Anchors and Traditional Bioabsorbable Anchors in Foot and Ankle Surgery.

Science.gov (United States)

Hembree, W Chad; Tsai, Michael A; Parks, Brent G; Miller, Stuart D

We compared the pullout strength of a suture-based anchor versus a bioabsorbable anchor in the distal fibula and calcaneus and evaluated the relationship between bone mineral density and peak load to failure. Eight paired cadaveric specimens underwent a modified Broström procedure and Achilles tendon reattachment. The fibula and calcaneus in the paired specimens received either a suture-based anchor or a bioabsorbable suture anchor. The fibular and calcaneal specimens were loaded to failure, defined as a substantial decrease in the applied load or pullout from the bone. In the fibula, the peak load to failure was significantly greater with the suture-based versus the bioabsorbable anchors (133.3 ± 41.8 N versus 76.8 ± 35.3 N; p = .002). No significant difference in load with 5 mm of displacement was found between the 2 groups. In the calcaneus, no difference in the peak load to failure was found between the 2 groups, and the peak load to failure with 5 mm of displacement was significantly lower with the suture-based than with the bioabsorbable anchors (52.2 ± 9.8 N versus 75.9 ± 12.4 N; p = .003). Bone mineral density and peak load to failure were significantly correlated in the fibula with the suture-based anchor. An innovative suture-based anchor had a greater peak load to failure compared with a bioabsorbable anchor in the fibula. In the calcaneus, the load at 5 mm of displacement was significantly lower in the suture-based than in the bioabsorbable group. The correlation findings might indicate the need for a cortical bone shelf with the suture-based anchor. Suture-based anchors could be a viable alternative to bioabsorbable anchors for certain foot and ankle procedures. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Anchoring in a novel bimanual coordination pattern.

Science.gov (United States)

Maslovat, Dana; Lam, Melanie Y; Brunke, Kirstin M; Chua, Romeo; Franks, Ian M

2009-02-01

Anchoring in cyclical movements has been defined as regions of reduced spatial or temporal variability [Beek, P. J. (1989). Juggling dynamics. PhD thesis. Amsterdam: Free University Press] that are typically found at movement reversal points. For in-phase and anti-phase movements, synchronizing reversal points with a metronome pulse has resulted in decreased anchor point variability and increased pattern stability [Byblow, W. D., Carson, R. G., & Goodman, D. (1994). Expressions of asymmetries and anchoring in bimanual coordination. Human Movement Science, 13, 3-28; Fink, P. W., Foo, P., Jirsa, V. K., & Kelso, J. A. S. (2000). Local and global stabilization of coordination by sensory information. Experimental Brain Research, 134, 9-20]. The present experiment examined anchoring during acquisition, retention, and transfer of a 90 degrees phase-offset continuous bimanual coordination pattern (whereby the right limb lags the left limb by one quarter cycle), involving horizontal flexion about the elbow. Three metronome synchronization strategies were imposed: participants either synchronized maximal flexion of the right arm (i.e., single metronome), both flexion and extension of the right arm (i.e., double metronome within-limb), or flexion of each arm (i.e., double metronome between-limb) to an auditory metronome. In contrast to simpler in-phase and anti-phase movements, synchronization of additional reversal points to the metronome did not reduce reversal point variability or increase pattern stability. Furthermore, practicing under different metronome synchronization strategies did not appear to have a significant effect on the rate of acquisition of the pattern.

Experimental Research on Destruction Mode and Anchoring Performance of Carbon Fiber Phyllostachys pubescens Anchor Rod with Different Forms

Directory of Open Access Journals (Sweden)

Wang Yulan

2018-01-01

Full Text Available The anchoring technology is extensively applied in reinforcing protection of the earth relics. Now that no specification is available for different new anchor rods in earth relics protection due to diversified destruction modes of earth relics and complexity of engineering technology conditions, it is urgent to guide reinforcing design and construction with a complete detailed anchor rod research document. With the new carbon fiber Phyllostachys pubescens anchor rod as the research object, six lots of in situ tests are designed to, respectively, study the destruction mode and anchoring performance of the carbon fiber Phyllostachys pubescens anchor rod under different anchor length L, anchor rod diameter D, bore diameter H, grouting material S, rib spacing R, and inclination angle A in this paper. By studying load shift curve experiment in drawing of the anchor rod, the destruction mode and ultimate bearing capacity of the carbon fiber Phyllostachys pubescens anchor rod in different experiment lots are obtained, and the concept of permitted application value N in anchor rod design is proposed. By studying strain distribution characteristics of anchor rods in experimental lots along the length direction under action of the permitted application value N and combining the existing destruction mode and ultimate bearing capacity, this paper analyzes influences of L, D, H, S, R, and A on anchoring effect of the carbon fiber Phyllostachys pubescens anchor rod; gives the reasonable value range of L, D, H, and R when the carbon fiber Phyllostachys pubescens anchor rod is used for reinforcing design of the earth relics; and provides favorable experiment basis for reinforcing design of the earth relics based on the carbon fiber Phyllostachys pubescens anchor rod.

Experimental testing of anchoring devices for bottom rails in partially anchored timber frame shear walls

OpenAIRE

Caprolu, Giuseppe

2011-01-01

Källsner and Girhammar have presented a new plastic design method of wood-framed shear walls at ultimate limit state. This method allows the designer to calculate the load-carrying capacity of shear walls partially anchored, where the leading stud is not anchored against the uplift.The anchorage system of shear walls is provided from anchor bolts and hold downs. Anchor bolts provide horizontal shear continuity between the bottom rail and the foundation. Hold downs are directly connected from ...

Results of the ANCHOR prospective, multicenter registry of EndoAnchors for type Ia endoleaks and endograft migration in patients with challenging anatomy.

Science.gov (United States)

Jordan, William D; Mehta, Manish; Varnagy, David; Moore, William M; Arko, Frank R; Joye, James; Ouriel, Kenneth; de Vries, Jean-Paul

2014-10-01

were unrelated to EndoAnchors. There were no open surgical conversions, there were no aneurysm-related deaths, and no aneurysm ruptured during follow-up. Use of EndoAnchors to treat existing and acute type Ia endoleaks and endograft migration was successful in most cases. Prophylactic use of EndoAnchors in patients with hostile aortic neck anatomy appears promising, but definitive conclusions must await longer term follow-up data. Published by Elsevier Inc.

Selecting fillers on emotional appearance improves lineup identification accuracy.

Science.gov (United States)

Flowe, Heather D; Klatt, Thimna; Colloff, Melissa F

2014-12-01

Mock witnesses sometimes report using criminal stereotypes to identify a face from a lineup, a tendency known as criminal face bias. Faces are perceived as criminal-looking if they appear angry. We tested whether matching the emotional appearance of the fillers to an angry suspect can reduce criminal face bias. In Study 1, mock witnesses (n = 226) viewed lineups in which the suspect had an angry, happy, or neutral expression, and we varied whether the fillers matched the expression. An additional group of participants (n = 59) rated the faces on criminal and emotional appearance. As predicted, mock witnesses tended to identify suspects who appeared angrier and more criminal-looking than the fillers. This tendency was reduced when the lineup fillers matched the emotional appearance of the suspect. Study 2 extended the results, testing whether the emotional appearance of the suspect and fillers affects recognition memory. Participants (n = 1,983) studied faces and took a lineup test in which the emotional appearance of the target and fillers was varied between subjects. Discrimination accuracy was enhanced when the fillers matched an angry target's emotional appearance. We conclude that lineup member emotional appearance plays a critical role in the psychology of lineup identification. The fillers should match an angry suspect's emotional appearance to improve lineup identification accuracy. PsycINFO Database Record (c) 2014 APA, all rights reserved.

An Accessory Protein Required for Anchoring and Assembly of Amyloid Fibers in B. subtilis Biofilms

Science.gov (United States)

Romero, Diego; Vlamakis, Hera; Losick, Richard; Kolter, Roberto

2011-01-01

Cells within Bacillus subtilis biofilms are held in place by an extracellular matrix that contains cell-anchored amyloid fibers, composed of the amyloidogenic protein TasA. As biofilms age they disassemble because the cells release the amyloid fibers. This release appears to be the consequence of incorporation of D-tyrosine, D-leucine, D-tryptophan and D-methionine into the cell wall. Here, we characterize the in vivo roles of an accessory protein TapA (TasA anchoring/assembly protein; previously YqxM) that serves both to anchor the fibers to the cell wall and to assemble TasA into fibers. TapA is found in discrete foci in the cell envelope and these foci disappear when cells are treated with a mixture of D-amino acids. Purified cell wall sacculi retain a functional form of this anchoring protein such that purified fibers can be anchored to the sacculi in vitro. In addition, we show that TapA is essential for the proper assembly of the fibers. Its absence results in a dramatic reduction in TasA levels and what little TasA is left produces only thin fibers that are not anchored to the cell. PMID:21477127

Unintended anchors: Building rating systems and energy performance goals for U.S. buildings

International Nuclear Information System (INIS)

Klotz, Leidy; Mack, Daniel; Klapthor, Brent; Tunstall, Casey; Harrison, Jennilee

2010-01-01

In the U.S., where buildings account for 40% of energy use, commercial buildings use more energy per unit area than ever before. However, exemplary buildings demonstrate the feasibility of much better energy performance at no additional first cost. This research examines one possible explanation for this inconsistency. The aim is to investigate whether the anchoring bias, which refers to our tendency to gravitate towards a pre-defined standard regardless of its relevance, influences energy performance goals in building design. The scope examines professionals who help set energy performance goals for U.S. buildings. Prior to being asked to set an energy performance goal, these professionals were randomly directed to one of three series of questions. One series set an anchor of 90% energy reduction beyond standard practice, one set a 30% anchor, and one set no anchor. Respondents exposed to the 90% anchor, and respondents exposed to no anchor at all, set higher energy performance goals than respondents exposed to the 30% anchor. These results suggest that building rating systems that only reward incremental energy improvements may inadvertently create anchors, thereby discouraging more advanced energy performance goals and inhibiting energy performance that is technically and economically feasible.

GPI-anchored protein organization and dynamics at the cell surface.

Science.gov (United States)

Saha, Suvrajit; Anilkumar, Anupama Ambika; Mayor, Satyajit

2016-02-01

The surface of eukaryotic cells is a multi-component fluid bilayer in which glycosylphosphatidylinositol (GPI)-anchored proteins are an abundant constituent. In this review, we discuss the complex nature of the organization and dynamics of GPI-anchored proteins at multiple spatial and temporal scales. Different biophysical techniques have been utilized for understanding this organization, including fluorescence correlation spectroscopy, fluorescence recovery after photobleaching, single particle tracking, and a number of super resolution methods. Major insights into the organization and dynamics have also come from exploring the short-range interactions of GPI-anchored proteins by fluorescence (or Förster) resonance energy transfer microscopy. Based on the nanometer to micron scale organization, at the microsecond to the second time scale dynamics, a picture of the membrane bilayer emerges where the lipid bilayer appears inextricably intertwined with the underlying dynamic cytoskeleton. These observations have prompted a revision of the current models of plasma membrane organization, and suggest an active actin-membrane composite. Copyright © 2016 by the American Society for Biochemistry and Molecular Biology, Inc.

Using Anchoring Vignettes to Adjust Self-Reported Personality: A Comparison Between Countries

Science.gov (United States)

Weiss, Selina; Roberts, Richard D.

2018-01-01

Data from self-report tools cannot be readily compared between cultures due to culturally specific ways of using a response scale. As such, anchoring vignettes have been proposed as a suitable methodology for correcting against this difference. We developed anchoring vignettes for the Big Five Inventory-44 (BFI-44) to supplement its Likert-type response options. Based on two samples (Rwanda: n = 423; Philippines: n = 143), we evaluated the psychometric properties of the measure both before and after applying the anchoring vignette adjustment. Results show that adjusted scores had better measurement properties, including improved reliability and a more orthogonal correlational structure, relative to scores based on the original Likert scale. Correlations of the Big Five Personality Factors with life satisfaction were essentially unchanged after the vignette-adjustment while correlations with counterproductive were noticeably lower. Overall, these changed findings suggest that the use of anchoring vignette methodology improves the cross-cultural comparability of self-reported personality, a finding of potential interest to the field of global workforce research and development as well as educational policymakers. PMID:29593621

Using Anchoring Vignettes to Adjust Self-Reported Personality: A Comparison Between Countries

Directory of Open Access Journals (Sweden)

Selina Weiss

2018-03-01

Full Text Available Data from self-report tools cannot be readily compared between cultures due to culturally specific ways of using a response scale. As such, anchoring vignettes have been proposed as a suitable methodology for correcting against this difference. We developed anchoring vignettes for the Big Five Inventory-44 (BFI-44 to supplement its Likert-type response options. Based on two samples (Rwanda: n = 423; Philippines: n = 143, we evaluated the psychometric properties of the measure both before and after applying the anchoring vignette adjustment. Results show that adjusted scores had better measurement properties, including improved reliability and a more orthogonal correlational structure, relative to scores based on the original Likert scale. Correlations of the Big Five Personality Factors with life satisfaction were essentially unchanged after the vignette-adjustment while correlations with counterproductive were noticeably lower. Overall, these changed findings suggest that the use of anchoring vignette methodology improves the cross-cultural comparability of self-reported personality, a finding of potential interest to the field of global workforce research and development as well as educational policymakers.

Comparison between suture anchor and transosseous suture for the modified-Broström procedure.

Science.gov (United States)

Cho, Byung-Ki; Kim, Yong-Min; Kim, Dong-Soo; Choi, Eui-Sung; Shon, Hyun-Chul; Park, Kyoung-Jin

2012-06-01

This prospective, randomized study was conducted to compare clinical outcomes of the modified Broström procedure using suture anchor or transosseous suture technique for chronic ankle instability. Forty patients were followed for more than 2 years after modified Broström procedure. Twenty procedures using a suture anchor and 20 procedures using a transosseous suture were performed by one surgeon. The clinical evaluation consisted of the Karlsson scale and the Sefton grading system. Talar tilt and anterior talar translation were measured on anterior and varus stress radiographs. The Karlsson scale had improved significantly to 90.8 points in the suture anchor group, and to 89.2 points in the transosseous suture group. According to Sefton grading system, 18 patients (90%) in suture anchor group and 17 patients (85%) in transosseous suture group achieved satisfactory results. The talar tilt angle and anterior talar translation improved significantly to 5.9 degrees and 4.2 mm in suture anchor group, and to 5.4 degrees and 4.1 mm in transosseous suture group, respectively. No significant differences existed in clinical and functional outcomes between the two techniques for ligament reattachment. Both modified Broström procedures using the suture anchor and transosseous suture seem to be effective treatment methods for chronic lateral ankle instability.

Not all Anchors Weigh Equally.

Science.gov (United States)

Greenstein, Michael; Velazquez, Alexandra

2017-11-01

The anchoring bias is a reliable effect wherein a person's judgments are affected by initially presented information, but it is unknown specifically why this effect occurs. Research examining this bias suggests that elements of both numeric and semantic priming may be involved. To examine this, the present research used a phenomenon wherein people treat numeric information presented differently in Arabic numeral or verbal formats. We presented participants with one of many forms of an anchor that represented the same value (e.g., twelve hundred or 1,200). Thus, we could examine how a concept's meaning and its absolute numeric value affect anchoring. Experiments 1 and 2 showed that people respond to Arabic and verbal anchors differently. Experiment 3 showed that these differences occurred largely because people tend to think of numbers in digit format. This suggests that one's conceptual understanding of the anchored information matters more than its strict numeric value.

Stone anchors from Minicoy Island, Lakshadweep, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

and Ali Rajas of Kerala. It appears that the mainland had contact with these islands during the early centuries of the Christian era, if not earlier (Sila Tripati, 1999). Though Islam came to Lakshadweep after the 11th and 12th centuries AD..., stitches, ropes and even sails (Hourani, 1995). With the passage of time the maritime contacts between the people of Lakshadweep and Arabs became closer, as demonstrated by the discovery of an Indo- 3 Arabian stone anchor in the Jama Mosque on Minicoy...

An accessory protein required for anchoring and assembly of amyloid fibres in B. subtilis biofilms.

Science.gov (United States)

Romero, Diego; Vlamakis, Hera; Losick, Richard; Kolter, Roberto

2011-06-01

Cells within Bacillus subtilis biofilms are held in place by an extracellular matrix that contains cell-anchored amyloid fibres, composed of the amyloidogenic protein TasA. As biofilms age they disassemble because the cells release the amyloid fibres. This release appears to be the consequence of incorporation of D-tyrosine, D-leucine, D-tryptophan and D-methionine into the cell wall. Here, we characterize the in vivo roles of an accessory protein TapA (TasA anchoring/assembly protein; previously YqxM) that serves both to anchor the fibres to the cell wall and to assemble TasA into fibres. TapA is found in discrete foci in the cell envelope and these foci disappear when cells are treated with a mixture of D-amino acids. Purified cell wall sacculi retain a functional form of this anchoring protein such that purified fibres can be anchored to the sacculi in vitro. In addition, we show that TapA is essential for the proper assembly of the fibres. Its absence results in a dramatic reduction in TasA levels and what little TasA is left produces only thin fibres that are not anchored to the cell. © 2011 Blackwell Publishing Ltd.

Bone anchors or interference screws? A biomechanical evaluation for autograft ankle stabilization.

Science.gov (United States)

Jeys, Lee; Korrosis, Sotiris; Stewart, Todd; Harris, Nicholas J

2004-01-01

Autograft stabilization uses free semitendinosus tendon grafts to anatomically reconstruct the anterior talofibular ligament. Study aims were to evaluate the biomechanical properties of Mitek GII anchors compared with the Arthrex Bio-Tenodesis Screw for free tendon reconstruction of the anterior talofibular ligament. There are no differences in load to failure and percentage specimen elongation at failure between the 2 methods. Controlled laboratory study using porcine models. Sixty porcine tendon constructs were failure tested. Re-creating the pull of the anterior talofibular ligament, loads were applied at 70 degrees to the bones. Thirty-six tendons were fixed to porcine tali and tested using a single pull to failure; 10 were secured with anchors and No. 2 Ethibond, 10 with anchors and FiberWire, 10 with screws and Fiberwire, and 6 with partially gripped screws. Cyclic preloading was conducted on 6 tendons fixed by anchors and on 6 tendons fixed by screws before failure testing. Two groups of 6 components fixed to the fibula were also tested. The talus single-pull anchor group produced a mean load of 114 N and elongation of 37% at failure. The talus single-pull screw group produced a mean load of 227 N and elongation of 22% at failure (P anchors. The improved biomechanics of interference screws suggests that these may be more suited to in vivo reconstruction of the anterior talofibular ligament than are bone anchors.

A Study on the Holding Capacity Safety Factors for Torpedo Anchors

Directory of Open Access Journals (Sweden)

Luís V. S. Sagrilo

2012-01-01

Full Text Available The use of powerful numerical tools based on the finite-element method has been improving the prediction of the holding capacity of fixed anchors employed by the offshore oil industry. One of the main achievements of these tools is the reduction of the uncertainty related to the holding capacity calculation of these anchors. Therefore, it is also possible to reduce the values of the associated design safety factors, which have been calibrated relying on models with higher uncertainty, without impairing the original level of structural safety. This paper presents a study on the calibration of reliability-based safety factors for the design of torpedo anchors considering the statistical model uncertainty evaluated using results from experimental tests and their correspondent finite-element-based numerical predictions. Both working stress design (WSD and load and resistance factors design (LRFD design methodologies are investigated. Considering the WSD design methodology, the single safety is considerably lower than the value typically employed in the design of torpedo anchors. Moreover, a LRFD design code format for torpedo anchors is more appropriate since it leads to designs having less-scattered safety levels around the target value.

Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application.

Science.gov (United States)

Vabbilisetty, Pratima; Boron, Mallorie; Nie, Huan; Ozhegov, Evgeny; Sun, Xue-Long

2018-02-28

Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell's functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine-poly(ethylene glycol)-dibenzocyclooctyne (DSPE-PEG 2000 -DBCO) and cholesterol-PEG-dibenzocyclooctyne (CHOL-PEG 2000 -DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids.

Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application

Science.gov (United States)

2018-01-01

Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell’s functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine–poly(ethylene glycol)–dibenzocyclooctyne (DSPE–PEG2000–DBCO) and cholesterol–PEG–dibenzocyclooctyne (CHOL–PEG2000–DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids. PMID:29503972

The anchor-based minimal important change, based on receiver operating characteristic analysis or predictive modeling, may need to be adjusted for the proportion of improved patients.

Science.gov (United States)

Terluin, Berend; Eekhout, Iris; Terwee, Caroline B

2017-03-01

Patients have their individual minimal important changes (iMICs) as their personal benchmarks to determine whether a perceived health-related quality of life (HRQOL) change constitutes a (minimally) important change for them. We denote the mean iMIC in a group of patients as the "genuine MIC" (gMIC). The aims of this paper are (1) to examine the relationship between the gMIC and the anchor-based minimal important change (MIC), determined by receiver operating characteristic analysis or by predictive modeling; (2) to examine the impact of the proportion of improved patients on these MICs; and (3) to explore the possibility to adjust the MIC for the influence of the proportion of improved patients. Multiple simulations of patient samples involved in anchor-based MIC studies with different characteristics of HRQOL (change) scores and distributions of iMICs. In addition, a real data set is analyzed for illustration. The receiver operating characteristic-based and predictive modeling MICs equal the gMIC when the proportion of improved patients equals 0.5. The MIC is estimated higher than the gMIC when the proportion improved is greater than 0.5, and the MIC is estimated lower than the gMIC when the proportion improved is less than 0.5. Using an equation including the predictive modeling MIC, the log-odds of improvement, the standard deviation of the HRQOL change score, and the correlation between the HRQOL change score and the anchor results in an adjusted MIC reflecting the gMIC irrespective of the proportion of improved patients. Adjusting the predictive modeling MIC for the proportion of improved patients assures that the adjusted MIC reflects the gMIC. We assumed normal distributions and global perceived change scores that were independent on the follow-up score. Additionally, floor and ceiling effects were not taken into account. Copyright © 2017 Elsevier Inc. All rights reserved.

Installation of concrete expansion anchors at the Fast Flux Test Facility

International Nuclear Information System (INIS)

Clark, G.L.

1980-01-01

Installation criteria utilized at the Fast Flux Test Facility for concrete expansion anchors are presented. Static and dynamic load capabilities of various anchor types are discussed in relation to design loads, with particular emphasis placed on the yield load (the proportional limit). Effects of several variables (i.e., installation torque, hole diameter) are also investigated. Resolution and documentation of field problems (e.g., improper spacing, embedment, angularity) are also described. Recommendations for improving and controlling future installations are given

Biomechanical comparison of traditional anchors to all-suture anchors in a double-row rotator cuff repair cadaver model.

Science.gov (United States)

Goschka, Andrew M; Hafer, Jason S; Reynolds, Kirk A; Aberle, Nicholas S; Baldini, Todd H; Hawkins, Monica J; McCarty, Eric C

2015-10-01

To further reduce the invasiveness of arthroscopic rotator cuff repair surgery the all-suture anchor has been developed. The all-suture anchor requires less bone removal and reduces the potential of loose body complications. The all-suture anchor must also have adequate biomechanical strength for the repair to heal. The hypothesis is there is no significant difference in the biomechanical performance of supraspinatus repairs using an all-suture anchor when compared to traditional solid-body suture anchors. Using nine shoulders per group, the supraspinatus tendon was dissected from the greater tuberosity. The four different double row repairs tested were (medial row/lateral row): A: ICONIX2/ICONIX2; B: ICONIX2/Stryker ReelX 3.9mm; C: ICONIX2/Stryker ReelX 4.5mm; D: Arthrex BioComposite CorkScrew FT 4.5mm/Arthrex BioComposite SwiveLock 4.75mm. The ICONIX2 was the only all-suture anchor tested. Tendons underwent cyclic loading from 10 to 100N for 500 cycles, followed by load-to-failure. Data was collected at cycles 5, 100, 200, 300, 400, and 500. One-way ANOVA analysis was used to assess significance (P≤0.05). The anchor combinations tested did not differ significantly in anterior (P>0.4) or posterior (P>0.3) gap formation, construct stiffness (P>0.7), ultimate load (P=0.06), or load to 5mm gap formation (P=0.84). The all-suture anchor demonstrated comparable biomechanical performance in multiple double-row anchor combinations to a combination of traditional solid-body anchors. Thus it may be an attractive option to further reduce the invasiveness of rotator cuff repairs. Copyright © 2015 Elsevier Ltd. All rights reserved.

An Improved Thermal Blooming Model for the Laser Performance Code Anchor

Science.gov (United States)

2016-06-01

over which a laser beam can maintain transverse coherence throughout its propagation distance. Typical values of ro are on the order of a few...G. Gebhardt, “Twenty-five years of thermal blooming: An overview,” in Proceedings of SPIE 1221 Propagation of High-Energy Laser Beams Through the...TERMS thermal blooming, atmospheric propagation , laser , scaling code, Strehl ratio, ANCHOR, COAMPS, NAVSLaM, LEEDR 15. NUMBER OF PAGES 77 16

Side-by-side comparison of Raman spectra of anchored and suspended carbon nanomaterials

International Nuclear Information System (INIS)

Sidorov, Anton N; Pabba, Santosh; Cohn, Robert W; Sumanasekera, G U; Hewaparakrama, Kapila P

2008-01-01

Raman spectra of ordered carbon nanomaterials are quite sensitive to surface perturbations, including trace residues, structural defects and residual stress. This is demonstrated by a series of experiments with carbon nanotubes and graphene. Their spectra change due to subtle changes in preparation and attachment to the substrate and to each other. Differences are most clearly seen by forming a material into an air bridge and probing it in the air gap and at the anchor points. A monolayer graphene sheet, shows a larger disorder band at the anchor points than in the air gap. However, a bundle or rope of parallel-aligned single-wall nanotubes shows a larger disorder band in the gap than at the anchor points. For the graphene sheet the substrate surface deforms the graphene, leading to increases in the disorder band. For the rope, the close proximity of the nanotubes to each other appears to produce a larger stress than the rope resting on the substrate

Microgravity Drill and Anchor System

Science.gov (United States)

Parness, Aaron; Frost, Matthew A.; King, Jonathan P.

2013-01-01

This work is a method to drill into a rock surface regardless of the gravitational field or orientation. The required weight-on-bit (WOB) is supplied by a self-contained anchoring mechanism. The system includes a rotary percussive coring drill, forming a complete sampling instrument usable by robot or human. This method of in situ sample acquisition using micro - spine anchoring technology enables several NASA mission concepts not currently possible with existing technology, including sampling from consolidated rock on asteroids, providing a bolt network for astronauts visiting a near-Earth asteroid, and sampling from the ceilings or vertical walls of lava tubes and cliff faces on Mars. One of the most fundamental parameters of drilling is the WOB; essentially, the load applied to the bit that allows it to cut, creating a reaction force normal to the surface. In every drilling application, there is a minimum WOB that must be maintained for the system to function properly. In microgravity (asteroids and comets), even a small WOB could not be supported conventionally by the weight of the robot or astronaut. An anchoring mechanism would be needed to resist the reactions, or the robot or astronaut would push themselves off the surface and into space. The ability of the system to anchor itself to a surface creates potential applications that reach beyond use in low gravity. The use of these anchoring mechanisms as end effectors on climbing robots has the potential of vastly expanding the scope of what is considered accessible terrain. Further, because the drill is supported by its own anchor rather than by a robotic arm, the workspace is not constrained by the reach of such an arm. Yet, if the drill is on a robotic arm, it has the benefit of not reflecting the forces of drilling back to the arm s joints. Combining the drill with the anchoring feet will create a highly mobile, highly stable, and highly reliable system. The drilling system s anchor uses hundreds of

Monogenean anchor morphometry: systematic value, phylogenetic signal, and evolution

Science.gov (United States)

Soo, Oi Yoon Michelle; Tan, Wooi Boon; Lim, Lee Hong Susan

2016-01-01

Background. Anchors are one of the important attachment appendages for monogenean parasites. Common descent and evolutionary processes have left their mark on anchor morphometry, in the form of patterns of shape and size variation useful for systematic and evolutionary studies. When combined with morphological and molecular data, analysis of anchor morphometry can potentially answer a wide range of biological questions. Materials and Methods. We used data from anchor morphometry, body size and morphology of 13 Ligophorus (Monogenea: Ancyrocephalidae) species infecting two marine mugilid (Teleostei: Mugilidae) fish hosts: Moolgarda buchanani (Bleeker) and Liza subviridis (Valenciennes) from Malaysia. Anchor shape and size data (n = 530) were generated using methods of geometric morphometrics. We used 28S rRNA, 18S rRNA, and ITS1 sequence data to infer a maximum likelihood phylogeny. We discriminated species using principal component and cluster analysis of shape data. Adams’s Kmult was used to detect phylogenetic signal in anchor shape. Phylogeny-correlated size and shape changes were investigated using continuous character mapping and directional statistics, respectively. We assessed morphological constraints in anchor morphometry using phylogenetic regression of anchor shape against body size and anchor size. Anchor morphological integration was studied using partial least squares method. The association between copulatory organ morphology and anchor shape and size in phylomorphospace was used to test the Rohde-Hobbs hypothesis. We created monogeneaGM, a new R package that integrates analyses of monogenean anchor geometric morphometric data with morphological and phylogenetic data. Results. We discriminated 12 of the 13 Ligophorus species using anchor shape data. Significant phylogenetic signal was detected in anchor shape. Thus, we discovered new morphological characters based on anchor shaft shape, the length between the inner root point and the outer root

The Holding Power of Anchors

Indian Academy of Sciences (India)

The efficiency of an anchor may be expressed as the ratio (holding force + weight of anchor). In dry sand .... the market at the beginning of the coming season in three sizes, namely 20, 35 and. 60 lb. These are ... Taylor frozen-flow hypothesis.

Anchoring effects on early autobiographical memories.

Science.gov (United States)

Greenberg, Daniel L; Bishara, Anthony J; Mugayar-Baldocchi, Marino A

2017-10-01

Studies of childhood memory typically show that our earliest memories come from between three and four years of age. This finding is not universal, however. The age estimate varies across cultures and is affected by social influences. Research from the judgments and decision-making literature suggests that these estimates might also involve a judgment under uncertainty. Therefore, they might be susceptible to less social influences such as heuristics and biases. To investigate this possibility, we conducted two experiments that used anchoring paradigms to influence participants' estimates of their age during early autobiographical memories. In Experiment 1, participants answered either a high-anchor or a low-anchor question, and were warned that the anchor was uninformative; they went on to estimate their age during their earliest autobiographical memory. In Experiment 2, we replicated Experiment 1 and extended the design to examine additional early autobiographical memories. In both experiments, participants in the low-anchor condition gave earlier age estimates than those in the high-anchor condition. These results provide new insights into the methods used to investigate autobiographical memory. Moreover, they show that reports of early autobiographical memories can be influenced by a relatively light touch - a change to a single digit in a single question.

An earth anchor system: installation and design guide.

Science.gov (United States)

R.L. Copstead; D.D. Studier

1990-01-01

A system for anchoring the guylines and skylines of cable yarding equipment is presented. A description of three types of tipping plate anchors is given. Descriptions of the installation equipment and methods specific to each type are given. Procedures for determining the correct number of anchors to install are included, as are guidelines for installing the anchors so...

An improved method of sample preparation on AnchorChip targets for MALDI-MS and MS/MS and its application in the liver proteome project

DEFF Research Database (Denmark)

Zhang, Xumin; Shi, Liang; Shu, Shaokung

2007-01-01

An improved method for sample preparation for MALDI-MS and MS/MS using AnchorChip targets is presented. The method, termed the SMW method (sample, matrix wash), results in better sensitivity for peptide mass fingerprinting as well as for sequencing by MS/MS than previously published methods. The ...

Ten Anchor Points for Teaching Principles of Marketing

Science.gov (United States)

Tomkovick, Chuck

2004-01-01

Effective marketing instructors commonly share a love for their students, an affinity for the subject matter, and a devotion to continuous quality improvement. The purpose of this article is to highlight 10 anchor points for teaching Principles of Marketing, which are designed to better engage students in the learning process. These anchor…

Murasaki: a fast, parallelizable algorithm to find anchors from multiple genomes.

Directory of Open Access Journals (Sweden)

Kris Popendorf

Full Text Available BACKGROUND: With the number of available genome sequences increasing rapidly, the magnitude of sequence data required for multiple-genome analyses is a challenging problem. When large-scale rearrangements break the collinearity of gene orders among genomes, genome comparison algorithms must first identify sets of short well-conserved sequences present in each genome, termed anchors. Previously, anchor identification among multiple genomes has been achieved using pairwise alignment tools like BLASTZ through progressive alignment tools like TBA, but the computational requirements for sequence comparisons of multiple genomes quickly becomes a limiting factor as the number and scale of genomes grows. METHODOLOGY/PRINCIPAL FINDINGS: Our algorithm, named Murasaki, makes it possible to identify anchors within multiple large sequences on the scale of several hundred megabases in few minutes using a single CPU. Two advanced features of Murasaki are (1 adaptive hash function generation, which enables efficient use of arbitrary mismatch patterns (spaced seeds and therefore the comparison of multiple mammalian genomes in a practical amount of computation time, and (2 parallelizable execution that decreases the required wall-clock and CPU times. Murasaki can perform a sensitive anchoring of eight mammalian genomes (human, chimp, rhesus, orangutan, mouse, rat, dog, and cow in 21 hours CPU time (42 minutes wall time. This is the first single-pass in-core anchoring of multiple mammalian genomes. We evaluated Murasaki by comparing it with the genome alignment programs BLASTZ and TBA. We show that Murasaki can anchor multiple genomes in near linear time, compared to the quadratic time requirements of BLASTZ and TBA, while improving overall accuracy. CONCLUSIONS/SIGNIFICANCE: Murasaki provides an open source platform to take advantage of long patterns, cluster computing, and novel hash algorithms to produce accurate anchors across multiple genomes with

Protein-Anchoring Therapy of Biglycan for Mdx Mouse Model of Duchenne Muscular Dystrophy.

Science.gov (United States)

Ito, Mikako; Ehara, Yuka; Li, Jin; Inada, Kosuke; Ohno, Kinji

2017-05-01

Duchenne muscular dystrophy (DMD) is a devastating muscle disease caused by loss-of-function mutations in DMD encoding dystrophin. No rational therapy is currently available. Utrophin is a paralog of dystrophin and is highly expressed at the neuromuscular junction. In mdx mice, utrophin is naturally upregulated throughout the muscle fibers, which mitigates muscular dystrophy. Protein-anchoring therapy was previously reported, in which a recombinant extracellular matrix (ECM) protein is delivered to and anchored to a specific target using its proprietary binding domains. Being prompted by a report that intramuscular and intraperitoneal injection of an ECM protein, biglycan, upregulates expression of utrophin and ameliorates muscle pathology in mdx mice, protein-anchoring therapy was applied to mdx mice. Recombinant adeno-associated virus serotype 8 (rAAV8) carrying hBGN encoding human biglycan was intravenously injected into 5-week-old mdx mice. The rAAV8-hBGN treatment improved motor deficits and decreased plasma creatine kinase activities. In muscle sections of treated mice, the number of central myonuclei and the distribution of myofiber sizes were improved. The treated mice increased gene expressions of utrophin and β1-syntrophin, as well as protein expressions of biglycan, utrophin, γ-sarcoglycan, dystrobrevin, and α1-syntrophin. The expression of hBGN in the skeletal muscle of the treated mice was 1.34-fold higher than that of the native mouse Bgn (mBgn). The low transduction efficiency and improved motor functions suggest that biglycan expressed in a small number of muscle fibers was likely to have been secreted and anchored to the cell surface throughout the whole muscular fibers. It is proposed that the protein-anchoring strategy can be applied not only to deficiency of an ECM protein as previously reported, but also to augmentation of a naturally induced ECM protein.

Improving the visual appearance for a small business

OpenAIRE

Niemonen, Jyri

2015-01-01

The objective of this thesis was to improve the brand and visual appearance for a small local business in Oulu. The commission by the client was to design a website, logo, and business cards. The company had been without a website and business cards since establishing the business in 1993. The old logo was last time updated in 2005. The thesis covers a theoretical research on colour, responsive design, and a usage of typography. The theoretical basis for the research was gathered from sev...

Testing and modeling of cyclically loaded rock anchors

Directory of Open Access Journals (Sweden)

Joar Tistel

2017-12-01

Full Text Available The Norwegian Public Roads Administration (NPRA is planning for an upgrade of the E39 highway route at the westcoast of Norway. Fixed links shall replace ferries at seven fjord crossings. Wide spans and large depths at the crossings combined with challenging subsea topography and environmental loads call for an extension of existing practice. A variety of bridge concepts are evaluated in the feasibility study. The structures will experience significant loads from deadweight, traffic and environment. Anchoring of these forces is thus one of the challenges met in the project. Large-size subsea rock anchors are considered a viable alternative. These can be used for anchoring of floating structures but also with the purpose of increasing capacity of fixed structures. This paper presents first a thorough study of factors affecting rock anchor bond capacity. Laboratory testing of rock anchors subjected to cyclic loading is thereafter presented. Finally, the paper presents a model predicting the capacity of a rock anchor segment, in terms of a ribbed bar, subjected to a cyclic load history. The research assumes a failure mode occurring in the interface between the rock anchor and the surrounding grout. The constitutive behavior of the bonding interface is investigated for anchors subjected to cyclic one-way tensile loads. The model utilizes the static bond capacity curve as a basis, defining the ultimate bond τbu and the slip s1 at τbu. A limited number of input parameters are required to apply the model. The model defines the bond-slip behavior with the belonging rock anchor capacity depending on the cyclic load level (τmax cy/τbu, the cyclic load ratio (R = τmin cy/τmax cy, and the number of load cycles (N. The constitutive model is intended to model short anchor lengths representing an incremental length of a complete rock anchor.

The bone-anchored hearing aid

DEFF Research Database (Denmark)

Foghsgaard, Søren

2014-01-01

The bone-anchored hearing aid (Baha) was introduced in 1977 by Tjellström and colleagues and has now been used clinically for over 30 years. Generally, the outcomes are good, and several studies have shown improved audiological- and quality of life outcomes. The principle of the Baha is, that sou...... vibrations are led directly to the inner ear via the mastoid bone, bypassing the middle ear. This is achieved via an osseointegrated implant and a skin-penetrating abutment. Studies report high success rates and a majority of complications as typically minor in nature....

Liquifying PLDLLA Anchor Fixation in Achilles Reconstruction for Insertional Tendinopathy.

Science.gov (United States)

Boden, Stephanie A; Boden, Allison L; Mignemi, Danielle; Bariteau, Jason T

2018-04-01

Insertional Achilles tendinopathy (IAT) is a frequent cause of posterior heel pain and is often associated with Haglund's deformity. Surgical correction for refractory cases of IAT has been well studied; however, the method of tendon fixation to bone in these procedures remains controversial, and to date, no standard technique has been identified for tendon fixation in these surgeries. Often, after Haglund's resection, there is large exposed cancellous surface for Achilles reattachment, which may require unique fixation to optimize outcomes. Previous studies have consistently demonstrated improved patient outcomes after Achilles tendon reconstruction with early rehabilitation with protected weight bearing, evidencing the need for a strong and stable anchoring of the Achilles tendon that allows early weight bearing without tendon morbidity. In this report, we highlight the design, biomechanics, and surgical technique of Achilles tendon reconstruction with Haglund's deformity using a novel technique that utilizes ultrasonic energy to liquefy the suture anchor, allowing it to incorporate into surrounding bone. Biomechanical studies have demonstrated superior strength of the suture anchor utilizing this novel technique as compared with prior techniques. However, future research is needed to ensure that outcomes of this technique are favorable when compared with outcomes using traditional suture anchoring methods. Level V: Operative technique.

Influence of Anchoring on Burial Depth of Submarine Pipelines.

Science.gov (United States)

Zhuang, Yuan; Li, Yang; Su, Wei

2016-01-01

Since the beginning of the twenty-first century, there has been widespread construction of submarine oil-gas transmission pipelines due to an increase in offshore oil exploration. Vessel anchoring operations are causing more damage to submarine pipelines due to shipping transportation also increasing. Therefore, it is essential that the influence of anchoring on the required burial depth of submarine pipelines is determined. In this paper, mathematical models for ordinary anchoring and emergency anchoring have been established to derive an anchor impact energy equation for each condition. The required effective burial depth for submarine pipelines has then been calculated via an energy absorption equation for the protection layer covering the submarine pipelines. Finally, the results of the model calculation have been verified by accident case analysis, and the impact of the anchoring height, anchoring water depth and the anchor weight on the required burial depth of submarine pipelines has been further analyzed.

A strategy for improved computational efficiency of the method of anchored distributions

Science.gov (United States)

Over, Matthew William; Yang, Yarong; Chen, Xingyuan; Rubin, Yoram

2013-06-01

This paper proposes a strategy for improving the computational efficiency of model inversion using the method of anchored distributions (MAD) by "bundling" similar model parametrizations in the likelihood function. Inferring the likelihood function typically requires a large number of forward model (FM) simulations for each possible model parametrization; as a result, the process is quite expensive. To ease this prohibitive cost, we present an approximation for the likelihood function called bundling that relaxes the requirement for high quantities of FM simulations. This approximation redefines the conditional statement of the likelihood function as the probability of a set of similar model parametrizations "bundle" replicating field measurements, which we show is neither a model reduction nor a sampling approach to improving the computational efficiency of model inversion. To evaluate the effectiveness of these modifications, we compare the quality of predictions and computational cost of bundling relative to a baseline MAD inversion of 3-D flow and transport model parameters. Additionally, to aid understanding of the implementation we provide a tutorial for bundling in the form of a sample data set and script for the R statistical computing language. For our synthetic experiment, bundling achieved a 35% reduction in overall computational cost and had a limited negative impact on predicted probability distributions of the model parameters. Strategies for minimizing error in the bundling approximation, for enforcing similarity among the sets of model parametrizations, and for identifying convergence of the likelihood function are also presented.

Ringstone anchors from Gujarat, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.; Bandodkar, S.N.

of Dwarka and Somanath have yielded several ringstone anchors along with other stone anchors such as triangular and grapnel types. The raw material used for these ring stones comprises basalt, sandstone and limestone. Earlier, these anchors were identified...

Spin selection at organic spinterface by anchoring group

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhao; Qiu, Shuai; Miao, Yuan-yuan; Ren, Jun-feng; Wang, Chuan-kui [School of Physics and Electronics, Shandong Normal University, Jinan 250014 (China); Hu, Gui-chao, E-mail: hgc@sdnu.edu.cn [School of Physics and Electronics, Shandong Normal University, Jinan 250014 (China); Institute of Theoretical Physics, Technische Universität Dresden, 01062 Dresden (Germany)

2017-07-01

Highlights: • The sign of interfacial spin polarization can be selected by using different anchoring groups. • A sp{sup 3}-d or sp-d hybridization may occur and induce spin polarization when the anchoring group changes. • Interfacial spin polarization depends on both the type of the outer orbital of the anchoring atom as well as its energy. - Abstract: Control of organic interfacial spin polarization is crucial in organic spintronics. Based on ab initio theory, here we proposed a spin selection at organic interface via anchoring group by adsorbing an organic molecule onto Ni(111) surface. The results demonstrate that either a positive or negative interfacial spin polarization may be obtained by choosing different anchoring groups. The orbital analysis via the projected density of states shows that the interfacial spin polarization is sensitive to the hybridization of the outer orbital of the anchoring atom as well as its energy relative to the d orbital of the ferromagnetic atom. The work indicates a feasible way to realize spin selection at the organic spinterface by anchoring group.

Attaching transmitters to waterbirds using one versus two subcutaneous anchors: Retention and survival trade-offs

Science.gov (United States)

Lewis, Tyler; Esler, Daniel N.; Uher-Koch, Brian D.; Dickson, Rian D.; Anderson, Eric M.; Evenson, Joseph R.; Hupp, Jerry; Flint, Paul L.

2017-01-01

A major challenge of wildlife telemetry is choosing an attachment technique that maximizes transmitter retention while minimizing negative side effects. For waterbirds, attachment of transmitters with subcutaneous anchors has been an effective and well-established technique, having been used on >40 species. This method was recently modified to include a second subcutaneous anchor, presumably increasing transmitter retention beyond that of single-anchor attachments. This putative benefit may be offset, however, by increased health risks related to additional incisions and subcutaneous protrusions. To test this potential trade-off, we attached radiotransmitters to molting and wintering surf (Melanitta perspicillata) and white-winged scoters (M. fusca) during 2008 and 2009 in Washington State and southeast Alaska, USA, using single- (121 scoters) and double-anchor (128 scoters) attachment techniques. We estimated daily probabilities of survival and radio retention for each group, this being apparent retention for wintering scoters because we could not differentiate shed transmitters from flighted emigration. For scoters during the flightless remigial molt, we found that addition of a second anchor increased cumulative retention probability (±SE) over a 49-day period from 0.69 ± 0.11 for single-anchor to 0.88 ± 0.07 for double-anchor attachments, while having no effect on survival. However, during winter, scoters with double-anchor attachments experienced no improvement in apparent retention, while having significantly lower survival during their first 14 days following transmitter attachment; of 15 mortalities during this period, 11 had 2 subcutaneous anchors. From day 15 onward, winter survival rates were nearly identical for single- versus double-anchor attachments, indicating that adverse effects of subcutaneous anchors were mainly limited to the 14-day postattachment period. Overall, given that the survival cost of adding a second subcutaneous anchor

Influence of Anchoring on Burial Depth of Submarine Pipelines.

Directory of Open Access Journals (Sweden)

Yuan Zhuang

Full Text Available Since the beginning of the twenty-first century, there has been widespread construction of submarine oil-gas transmission pipelines due to an increase in offshore oil exploration. Vessel anchoring operations are causing more damage to submarine pipelines due to shipping transportation also increasing. Therefore, it is essential that the influence of anchoring on the required burial depth of submarine pipelines is determined. In this paper, mathematical models for ordinary anchoring and emergency anchoring have been established to derive an anchor impact energy equation for each condition. The required effective burial depth for submarine pipelines has then been calculated via an energy absorption equation for the protection layer covering the submarine pipelines. Finally, the results of the model calculation have been verified by accident case analysis, and the impact of the anchoring height, anchoring water depth and the anchor weight on the required burial depth of submarine pipelines has been further analyzed.

Characterizing the flow of stirred vessels with anchor type impellers

Directory of Open Access Journals (Sweden)

S.M.C. Peixoto

2000-12-01

Full Text Available Despite its importance in chemical industries, there are few works which studies anchor type impellers and only a fraction of the works investigate these systems under a computational approach. The great majority refers to turbine impellers, specially Rushton turbines, under turbulent flow. Anchor impellers are used specially for highly viscous flow, typical of polymer reactions. The viscosity is normally in the range 1000-10000 cp. Since this range of viscosity describe highly viscous flows, the reactions for anchor agitated systems are normally carried out under laminar flow. This work presents a detailed computational fluid dynamics (CFD approach to study the behaviour of stirred vessels using anchor impellers. The axial plane of the tank, which is being modelled, is divided into small control volumes, which collectively is referred to as the mesh, or grid. In each of these cells the momentum balance, energy and mass conservation, which describes the model, are rewritten algebraically using the finite volumes method to relate such variables as velocity, pressure and temperature to values in neighbouring cells. The equations are then solved numerically, and the results yield the flow corresponding to the model. Since the geometry of a vessel with anchor impellers strictly calls for a three dimensional method, an approximation is made to account for the effect of the blades (Kuncewics, 1992. The main objective of this work is to give a detailed description of the flow generated by this axial impeller with a view to indicate ways in which the design and operation of these systems can be improved.

The Use of Comics-Based Cases in Anchored Instruction

Science.gov (United States)

Kneller, Matthew F.

2009-01-01

The primary purpose of this research was to understand how comics fulfill the role of anchor in an anchored instruction learning environment. Anchored instruction addresses the inert knowledge problem through the use of realistic multimedia stories, or "anchors," that embed a problem and the necessary data to solve it within the narrative. In the…

Dynamic performance of concrete undercut anchors for Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Mahrenholtz, Christoph, E-mail: christoph@mahrenholtz.net; Eligehausen, Rolf

2013-12-15

Graphical abstract: - Highlights: • Behavior of undercut anchors under dynamic actions simulating earthquakes. • First high frequency load and crack cycling tests on installed concrete anchors ever. • Comprehensive review of anchor qualification for Nuclear Power Plants. - Abstract: Post-installed anchors are widely used for structural and nonstructural connections to concrete. In many countries, concrete anchors used for Nuclear Power Plants have to be qualified to ensure reliable behavior even under extreme conditions. The tests required for qualification of concrete anchors are carried out at quasi-static loading rates well below the rates to be expected for dynamic actions deriving from earthquakes, airplane impacts or explosions. To investigate potentially beneficial effects of high loading rates and cycling frequencies, performance tests on installed undercut anchors were conducted. After introductory notes on anchor technology and a comprehensive literature review, this paper discusses the qualification of anchors for Nuclear Power Plants and the testing carried out to quantify experimentally the effects of dynamic actions on the load–displacement behavior of undercut anchors.

Testing Anchoring effect in CV Data from Dichotomous Choice with a Follow-up Questioning

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Cheol [Dae-Jin University, Pocheon (Korea)

1998-09-01

A questionnaire of dual bisected selection of CVM, which is an induced approach of intended payment, was suggested to overcome statistical inefficiency of a questionnaire of single bisected selection. In spite of several advantages of it, it is doubted that there would be an occurrence of anchoring effect, which is a psychological source of convenient starting point. Therefore, the general intended payment model, which can review the anchoring effect from CV questionnaire of dual bisected selection, was suggested and a mechanism that can review the anchoring effect from the model. This model is combining the dual variation model by Cameron and Quiggin (1994) with the results of bisected selective responses of a firstly presented particular amount as an explanatory variable of the second interior intended payment amount. If the sign of coefficient of the results of bisected selective responses of a firstly presented particular amount was negative and statistically significant, then it can be said that there is an anchoring effect. However, when there is uncertainty of occurrence of anchoring effect from the coefficient review, there is no need to worry about the anchoring effect if the average of estimated values of intended payment amount from two responses were different. As a result of applying this model and mechanism to CV materials on the improvement of water quality of the Han River, there is no need to worry about the anchoring effect. (author). 21 refs., 4 tabs.

End-anchored polymers in good solvents from the single chain limit to high anchoring densities.

Science.gov (United States)

Whitmore, Mark D; Grest, Gary S; Douglas, Jack F; Kent, Michael S; Suo, Tongchuan

2016-11-07

An increasing number of applications utilize grafted polymer layers to alter the interfacial properties of solid substrates, motivating refinement in our theoretical understanding of such layers. To assess existing theoretical models of them, we have investigated end-anchored polymer layers over a wide range of grafting densities, σ, ranging from a single chain to high anchoring density limits, chain lengths ranging over two orders of magnitude, for very good and marginally good solvent conditions. We compare Monte Carlo and molecular dynamics simulations, numerical self-consistent field calculations, and experimental measurements of the average layer thickness, h, with renormalization group theory, the Alexander-de Gennes mushroom theory, and the classical brush theory. Our simulations clearly indicate that appreciable inter-chain interactions exist at all simulated areal anchoring densities so that there is no mushroom regime in which the layer thickness is independent of σ. Moreover, we find that there is no high coverage regime in which h follows the predicted scaling, h ∼ Nσ 1/3 , for classical polymer brushes either. Given that no completely adequate analytic theory seems to exist that spans wide ranges of N and σ, we applied scaling arguments for h as a function of a suitably defined reduced anchoring density, defined in terms of the solution radius of gyration of the polymer chains and N. We find that such a scaling approach enables a smooth, unified description of h in very good solvents over the full range of anchoring density and chain lengths, although this type of data reduction does not apply to marginal solvent quality conditions.

Studies on the mechanical behavior of rock anchors. ; Results of in-situ pull-out tests. Rock anchor no rikigaku kyodo ni kansuru kenkyu. ; Gen prime ichi shiken ni okeru anchor no kyodo

Energy Technology Data Exchange (ETDEWEB)

Arimoto, K.; Ebisu, S.; Nakagawa, M.; Usui, M.; Someya, T.; Machida, N. (Okumura Corp., Tokyo (Japan))

1991-10-31

The rock anchor method is planned to apply to some permanent structures but since this method was developed for temporary structures, the clarification of the transferring mechanism of force from an anchor to a rockmass, the fracture mechanism and the development of the dynamic model have not been established. This paper arranged the data obtained by a full-scale, in-situ pulling out test of a rock anchor as the first step to understand the dynamic behavior and analyzed by paying attetion to the modulus of deformation of the rockmass where the anchor was embedded to elucidate the affecting degree of rockmass modulus of deformation, the embedded length and the tendon diameter on the dynamic behavior of the anchor. The rock anchor behavior could be expressed accurately by applying a theoretical solution derived by the balancing condition of forces at the boundary face. Especially, when the rockmass is uniform and the fracture occurrs at the interface between the tendon and grout, this approach can express the fracture with the accuracy similar to that made by the finite element method. 6 refs., 11 figs.,1 tab.

Containment liner plate anchors and steel embedments test results

International Nuclear Information System (INIS)

Chang-Lo, P.L.; Johnson, T.E.; Pfeifer, B.W.

1977-01-01

This paper summarizes test data on shear load and deformation capabilities for liner plate line anchors and structural steel embedments in reinforced and prestressed concrete nuclear containments. Reinforced and prestressed nuclear containments designed and constructed in the United States are lined with a minimum of 0.64 cm steel plate. The liner plates are anchored by the use of either studs or structural members (line anchors) which usually run in the vertical direction. This paper will only address line anchors. Static load versus displacement test data is necessary to assure that the design is adequate for the maximum loads. The test program for the liner anchors had the following major objectives: determine load versus displacement data for a variety of anchors considering structural tees and small beams with different weld configurations, from the preceding tests, determine which anchors would lead to an economical and extremely safe design and test these anchors for cyclic loads resulting from thermal fluctuations. Various concrete embeds in the containment and other structures are subjected to loads such as pipe rupture which results in shear. Since many of the loads are transient by nature, it is necessary to know the load-displacement relationship so that the energy absorption can be determined. The test program for the embeds had the following objectives: determine load-displacement relationship for various size anchors from 6.5 cm 2 to 26 cm 2 with maximum capacities of approximately 650 kN; determine the effect of various anchor width-to-thickness ratios for the same shear area

Modified Kidner procedure utilizing a Mitek bone anchor.

Science.gov (United States)

Dawson, D M; Julsrud, M E; Erdmann, B B; Jacobs, P M; Ringstrom, J B

1998-01-01

The recent development of small bone suture anchors has created several potential applications in reconstructive surgery of the foot. Mitek bone anchors are simple to insert, require less aggressive dissection and surgical time than reefing of the redundant posterior tibial tendon, and are a reliable method of tendon-to-bone fixation. Mitek bone anchors are an excellent technique for the treatment of redundant tibialis posterior tendon following a modified Kidner procedure. In modified Kidner procedures involving an excessively large os tibiale externum, Mitek anchoring of the redundant tibialis posterior tendon to the navicular bone is an excellent means for secure plication of the posterior tibial tendon in cases involving intraoperative tendon laxity. A description of the Mitek Anchor System and technique of application in a modified Kinder procedure is presented. The purpose of this study was to describe patient satisfaction and long-term clinical outcomes of the modified Kinder procedure with and without the Mitek bone anchoring system. A retrospective study of the modified Kinder procedure was performed with 13 patients being evaluated, seven with Mitek anchoring and six without. The University of Maryland 100-point Painful Foot Center Scoring System was modified to be more specific to the modified Kinder procedure for assessment of subjective long-term results. Patient overall satisfaction was rated good to excellent by 85.6% of patients in the Mitek group and by 100% of patients in the non-Mitek group. Use of the Mitek anchor allowed for quicker postoperative recovery to resumption of ambulation without assistive devices (average of 3 weeks vs. 4.42 weeks) and a quicker return to pain-free ambulation in normal shoegear (average of 4 weeks vs. 6 weeks). Mitek anchoring of the tibialis posterior tendon, theoretically, increases medial arch support as evidenced by 14% of the Mitek group and 67% of the non-Mitek group requiring postoperative orthotics.

Editorial Commentary: All-Suture Anchors, Foam Blocks, and Biomechanical Testing.

Science.gov (United States)

Brand, Jefferson C

2017-06-01

Barber's biomechanical work is well known to Arthroscopy's readers as thorough, comprehensive, and inclusive of new designs as they become available. In "All-Suture Anchors: Biomechanical Analysis of Pullout Strength, Displacement, and Failure Mode," the latest iteration, Barber and Herbert test all-suture anchors in both porcine femurs and biphasic foam. While we await in vivo clinical trials that compare all-suture anchors to currently used anchors, Barber and Herbert have provided data to inform anchor choice, and using their biomechanical data at time zero from all-suture anchor trials in an animal model, we can determine the anchors' feasibility for human clinical investigations. Copyright © 2017 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Adsorption phenomena and anchoring energy in nematic liquid crystals

CERN Document Server

Barbero, Giovanni

2005-01-01

Despite the large quantity of phenomenological information concerning the bulk properties of nematic phase liquid crystals, little is understood about the origin of the surface energy, particularly the surface, interfacial, and anchoring properties of liquid crystals that affect the performance of liquid crystal devices. Self-contained and unique, Adsorption Phenomena and Anchoring Energy in Nematic Liquid Crystals provides an account of new and established results spanning three decades of research into the problems of anchoring energy and adsorption phenomena in liquid crystals.The book contains a detailed discussion of the origin and possible sources of anchoring energy in nematic liquid crystals, emphasizing the dielectric contribution to the anchoring energy in particular. Beginning with fundamental surface and anchoring properties of liquid crystals and the definition of the nematic phase, the authors explain how selective ion adsorption, dielectric energy density, thickness dependence, and bias voltage...

Career anchors and learning plan (part one

Directory of Open Access Journals (Sweden)

Daniela Brečko

2006-12-01

Full Text Available The article is divided into three parts. The first part concentrates on how important career is for an individual, organization and society. The author establishes that understanding of career has changed dramatically and does not only refer to climbing up the career ladder, but also moving off or even down the career ladder. The notion of career, as a lifelong and professional path, encompasses all aspects of human personality and their roles acquired through one's life. On basis of vast and longitudinal research, where the author has studied career anchors of individuals, it is the objective of the author to find out on basis of what grounds do the individuals decide to take certain directions in their careers and how learning contributes to such decisions. As a source the author has used Shein's theory of career anchors. Part one describes in greater detail 8 different career anchors and introduces their main features with the findings of the research, which refer to the analysis of professions (work positions and established career anchors. The author thus verifies the hypothesis that career anchors do exist in our area.

Self-tapping ability of carbon fibre reinforced polyetheretherketone suture anchors.

Science.gov (United States)

Feerick, Emer M; Wilson, Joanne; Jarman-Smith, Marcus; Ó'Brádaigh, Conchur M; McGarry, J Patrick

2014-10-01

An experimental and computational investigation of the self-tapping ability of carbon fibre reinforced polyetheretherketone (CFR-PEEK) has been conducted. Six CFR-PEEK suture anchor designs were investigated using PEEK-OPTIMA® Reinforced, a medical grade of CFR-PEEK. Experimental tests were conducted to investigate the maximum axial force and torque required for self-taping insertion of each anchor design. Additional experimental tests were conducted for some anchor designs using pilot holes. Computational simulations were conducted to determine the maximum stress in each anchor design at various stages of insertion. Simulations also were performed to investigate the effect of wall thickness in the anchor head. The maximum axial force required to insert a self-tapping CFR-PEEK suture anchor did not exceed 150 N for any anchor design. The maximum torque required to insert a self-tapping CFR-PEEK suture anchor did not exceed 0.8 Nm. Computational simulations reveal significant stress concentrations in the region of the anchor tip, demonstrating that a re-design of the tip geometry should be performed to avoid fracture during self-tapping, as observed in the experimental component of this study. This study demonstrates the ability of PEEK-OPTIMA Reinforced suture anchors to self-tap polyurethane foam bone analogue. This provides motivation to further investigate the self-tapping ability of CFR-PEEK suture anchors in animal/cadaveric bone. An optimised design for CFR-PEEK suture anchors offers the advantages of radiolucency, and mechanical properties similar to bone with the ability to self-tap. This may have positive implications for reducing surgery times and the associated costs with the procedure. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Career anchors and values from different career management perspectives

Directory of Open Access Journals (Sweden)

Rodrigo Cunha da Silva

2016-06-01

Full Text Available Purpose – To analyze the relationships between career anchors and young Generation Y professionals’ values, from the career concept perspective. Design/methodology/approach – Research concerning the proposed objective was carried out through quantitative research involving 189 Business Administration majors from a Catholic university in São Paulo, Brazil. We used two instruments to identify the career anchors and values of respondents: Schein (1990 and Schwartz (1994, respectively. We used statistical techniques to explore the relationships between career anchors and values. Findings – Among the results, mention should be made to the statistical relationships found between analyzed career anchors and values. It is also important to stress that, although the Lifestyle career anchor was predominantly present in the conglomerate division, this anchor was the predominant characteristic in the differentiation of the smaller group of respondents, the new career group. The General Management Career Anchor, which presents a lower incidence, is the predominant characteristic of the larger group, referring to organizational careers. As well as the Lifestyle career anchor, the Hedonism value was predominant among respondents. Originality/value – The need to consider the following was found: Generation Y presents generational characteristics that drive people management to propose work structures that offer activities to generate learning, pleasure, self-fulfillment and conciliation between work and personal life.

Test Score Equating Using Discrete Anchor Items versus Passage-Based Anchor Items: A Case Study Using "SAT"® Data. Research Report. ETS RR-14-14

Science.gov (United States)

Liu, Jinghua; Zu, Jiyun; Curley, Edward; Carey, Jill

2014-01-01

The purpose of this study is to investigate the impact of discrete anchor items versus passage-based anchor items on observed score equating using empirical data.This study compares an "SAT"® critical reading anchor that contains more discrete items proportionally, compared to the total tests to be equated, to another anchor that…

On Moderator Detection in Anchoring Research: Implications of Ignoring Estimate Direction

Directory of Open Access Journals (Sweden)

Nathan N. Cheek

2018-05-01

Full Text Available Anchoring, whereby judgments assimilate to previously considered standards, is one of the most reliable effects in psychology. In the last decade, researchers have become increasingly interested in identifying moderators of anchoring effects. We argue that a drawback of traditional moderator analyses in the standard anchoring paradigm is that they ignore estimate direction—whether participants’ estimates are higher or lower than the anchor value. We suggest that failing to consider estimate direction can sometimes obscure moderation in anchoring tasks, and discuss three potential analytic solutions that take estimate direction into account. Understanding moderators of anchoring effects is essential for a basic understanding of anchoring and for applied research on reducing the influence of anchoring in real-world judgments. Considering estimate direction reduces the risk of failing to detect moderation.

Protein-anchoring therapy to target extracellular matrix proteins to their physiological destinations.

Science.gov (United States)

Ito, Mikako; Ohno, Kinji

2018-02-20

Endplate acetylcholinesterase (AChE) deficiency is a form of congenital myasthenic syndrome (CMS) caused by mutations in COLQ, which encodes collagen Q (ColQ). ColQ is an extracellular matrix (ECM) protein that anchors AChE to the synaptic basal lamina. Biglycan, encoded by BGN, is another ECM protein that binds to the dystrophin-associated protein complex (DAPC) on skeletal muscle, which links the actin cytoskeleton and ECM proteins to stabilize the sarcolemma during repeated muscle contractions. Upregulation of biglycan stabilizes the DPAC. Gene therapy can potentially ameliorate any disease that can be recapitulated in cultured cells. However, the difficulty of tissue-specific and developmental stage-specific regulated expression of transgenes, as well as the difficulty of introducing a transgene into all cells in a specific tissue, prevents us from successfully applying gene therapy to many human diseases. In contrast to intracellular proteins, an ECM protein is anchored to the target tissue via its specific binding affinity for protein(s) expressed on the cell surface within the target tissue. Exploiting this unique feature of ECM proteins, we developed protein-anchoring therapy in which a transgene product expressed even in remote tissues can be delivered and anchored to a target tissue using specific binding signals. We demonstrate the application of protein-anchoring therapy to two disease models. First, intravenous administration of adeno-associated virus (AAV) serotype 8-COLQ to Colq-deficient mice, resulting in specific anchoring of ectopically expressed ColQ-AChE at the NMJ, markedly improved motor functions, synaptic transmission, and the ultrastructure of the neuromuscular junction (NMJ). In the second example, Mdx mice, a model for Duchenne muscular dystrophy, were intravenously injected with AAV8-BGN. The treatment ameliorated motor deficits, mitigated muscle histopathologies, decreased plasma creatine kinase activities, and upregulated expression

Comparative Study on Different Slot Forms of Prestressed Anchor Blocks

Science.gov (United States)

Fan, Rong; Si, Jianhui; Jian, Zheng

2018-03-01

In this paper, two models of prestressed pier, rectangular cavity anchor block and arch hollow anchor block are established. The ABAQUS software was used to calculate the stress of the surface of the neck of the pier and the cavity of the anchor block, through comparative analysis. The results show that compared with the rectangular cavity anchor block, the stress of the pier and the cavity can be effectively reduced when the arch hole is used, and the amount of prestressed anchor can be reduced, so as to obtain obvious economic benefits.

Morphometric quantification of biodegradable PLDLLA-anchor implant-beds on magnetic resonance images of the humeral head

International Nuclear Information System (INIS)

Chatterjee, D.

2009-01-01

An overview of the functional anatomy of the human shoulder joint is the base for understanding of rotator cuff tears and its surgical repair by means of suture anchors. These anchors, manufactured of biodegradable polymers, do not (or not totally) degrade in the period of time postulated by the manufactures. Bone healing seems to be impaired. Radiological follow-ups of 8 months to years postoperative revealed osteolysis and even cystic deformation of the implant beds (=anchor-holes). In this present study the anchor-holes are morphometrically measured for the first time on MRT-images. For this prospective study MRIs from altogether 38 patients (20 female/18 male, age 43.9a - 81.6a) were selected after arthroscopic rotator cuff repair with 1-4 biodegradable suture anchors (PLDLLA 'Bio-Corkscrews', Arthrex Inc., Naples FL, USA) at a single institution. After signing an informed consent form patients' MRIs could be evaluated after a mean follow-up period of 15.8 and 36 months. The shapes of the bony implant beds were subjectively categorized and for the computer-assisted morphometry of the anchor-hole areas Adobe Photoshop; CS3 Extended (Version 10.0) was used and adapted. The results were statistically analyzed and correlated with the clinical success rate (Constant Score=CS). All anchor-holes were discernable for up to 42 months. A significant shift of threaded to cylindric anchor-hole shapes was evident from the 1 st to 2 nd follow-up. Only 11.5% of the anchor-holes showed a cystic enlargement. At the 1 st follow-up the anchor-hole areas increased on average by 50.87% compared to original anchor size. However, at the 2 nd follow-up all anchor-hole areas decreased significantly (p st follow-up. The average preoperative CS improved from 38.5 points to 87.4 (1 st follow-up) and then remained at 87 points (2 nd follow-up). Anchor-holes of biodegradable suture anchor are, as opposed to the time period claimed by the manufacturers, visible and thus not totally degraded

Biased calculations: Numeric anchors influence answers to math equations

Directory of Open Access Journals (Sweden)

Andrew R. Smith

2011-02-01

Full Text Available People must often perform calculations in order to produce a numeric estimate (e.g., a grocery-store shopper estimating the total price of his or her shopping cart contents. The current studies were designed to test whether estimates based on calculations are influenced by comparisons with irrelevant anchors. Previous research has demonstrated that estimates across a wide range of contexts assimilate toward anchors, but none has examined estimates based on calculations. In two studies, we had participants compare the answers to math problems with anchors. In both studies, participants' estimates assimilated toward the anchor values. This effect was moderated by time limit such that the anchoring effects were larger when the participants' ability to engage in calculations was limited by a restrictive time limit.

Anchoring in Destination-Therapy Left Ventricular Assist Device Decision Making: A Mechanical Turk Survey.

Science.gov (United States)

Paine, Arcadia M; Allen, Larry A; Thompson, Jocelyn S; McIlvennan, Colleen K; Jenkins, Amy; Hammes, Andrew; Kroehl, Miranda; Matlock, Daniel D

2016-11-01

People with end-stage heart failure may have to decide about destination-therapy left ventricular assist device (DT-LVAD). Individuals facing difficult decisions often rely on heuristics, such as anchoring, which predictably bias decision outcomes. We aimed to investigate whether showing a larger historical Heartmate XVE creates an anchoring effect, making the smaller Heartmate II (HMII) appear more favorable. With the use of Amazon Mechanical Turk, participants watched videos asking them to imagine themselves dying of end-stage heart failure, then were presented the option of LVAD as potentially life-prolonging therapy. Participants were randomized to a control group who were only shown the HMII device, and the intervention group who saw the XVE device before the HMII. Participants then completed surveys. A total of 487 participants completed the survey (control = 252; intervention = 235); 79% were affect likelihood of accepting the LVAD, it did affect device perception. This article highlights an important point with clinical implications: factors such as anchoring have the potential to inappropriately influence perceptions and decisions and should be carefully considered in research and practice. Copyright © 2016 Elsevier Inc. All rights reserved.

Additional Haptic Information Provided by Anchors Reduces Postural Sway in Young Adults Less Than Does Light Touch

Directory of Open Access Journals (Sweden)

Renato Moraes

2018-06-01

Full Text Available This study investigated the effect of adding haptic information to the control of posture, as well as comparing the effect of both the “light touch” (LT and “anchor system” (AS paradigms on postural sway. Additionally, it compared the effect of location and number of points of contact to the control of posture in young adults. The location consisted of using the anchors tied to the finger and held by the hands, and, for LT, the fingertip. For the number of points of contact, participants used two hands, and then separately the dominant hand, and the non-dominant hand, for both anchor and LT paradigms. Participants stood upright with feet-together and in tandem position while performing tasks that combined the use of anchors and LT, points of contact (hand grip and finger, and number of points of contact (two hands and one hand. In this study, the anchors consist of holding in each hand a flexible cable with the other end attached to the ground. The LT consists of slightly touching a rigid surface with the tip of the index finger. The results showed, first, that the anchors improved postural control less than did the LT. Second, they revealed that holding the anchors with the hands or with them tied to the fingertip resulted in a similar reduction in postural sway only in the tandem position. For the feet-together position, the anchors tied to the fingertip were ineffective. Similarly, the use of one or two hands did not affect the contribution of the anchors. However, using two hands in the LT condition was more effective than was one hand. Third, our results showed the presence of a temporal delay between force and center-of-pressure (COP for the anchors, only in the AP direction with feet-together. In conclusion, overall, the anchors were less effective in reducing postural sway than was the LT. The anchors attached to fingertips were as effective as the hand-held anchors in the tandem position, yet ineffective during foot

Arthroscopic Repair of Ankle Instability With All-Soft Knotless Anchors.

Science.gov (United States)

Pereira, Hélder; Vuurberg, Gwen; Gomes, Nuno; Oliveira, Joaquim Miguel; Ripoll, Pedro L; Reis, Rui Luís; Espregueira-Mendes, João; Niek van Dijk, C

2016-02-01

In recent years, arthroscopic and arthroscopically assisted techniques have been increasingly used to reconstruct the lateral ligaments of the ankle. Besides permitting the treatment of several comorbidities, arthroscopic techniques are envisioned to lower the amount of surgical aggression and to improve the assessment of anatomic structures. We describe our surgical technique for arthroscopic, two-portal ankle ligament repair using an all-soft knotless anchor, which is made exclusively of suture material. This technique avoids the need for classic knot-tying methods. Thus it diminishes the chance of knot migration caused by pendulum movements. Moreover, it avoids some complications that have been related to the use of metallic anchors and some currently available biomaterials. It also prevents prominent knots, which have been described as a possible cause of secondary complaints.

76 FR 30301 - Commercial Acquisition; Anchor Tenancy

Science.gov (United States)

2011-05-25

... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION 48 CFR Part 1812 RIN 2700-AD64 Commercial... consistent with NASA's authority under Section 401 of the Commercial Space Competitiveness Act (CSCA) of 1992. NASA may enter into multi-year anchor tenancy contracts for commercial space goods or services. Anchor...

A comparison of lateral ankle ligament suture anchor strength.

Science.gov (United States)

Barber, F Alan; Herbert, Morley A; Crates, John M

2013-06-01

Lateral ankle ligament repairs increasingly use suture anchors instead of bone tunnels. Our purpose was to compare the biomechanical properties of a knotted and knotless suture anchor appropriate for a lateral ankle ligament reconstruction. In porcine distal fibulae, 10 samples of 2 different PEEK anchors were inserted. The attached sutures were cyclically loaded between 10N and 60N for 200 cycles. A destructive pull was performed and failure loads, cyclic displacement, stiffness, and failure mode recorded. PushLock 2.5 anchors failed before 200 cycles. PushLock 100 cycle displacement was less than Morphix 2.5 displacement (panchors completing 200 cycles was 86.5N (PushLock) and 252.1N (Morphix) (panchor breaking and suture breakage. The knotted Morphix demonstrated more displacement and greater failure strength than the knotless PushLock. The PushLock failed consistently with suture breaking. The Morphix anchor failed both by anchor breaking and by suture breaking. Copyright © 2012 European Foot and Ankle Society. Published by Elsevier Ltd. All rights reserved.

Post-installed concrete anchors in nuclear power plants: Performance and qualification

International Nuclear Information System (INIS)

Mahrenholtz, Philipp; Eligehausen, Rolf

2015-01-01

Graphical abstract: - Highlights: • Review of qualification and design regulations for anchors in nuclear power plants. • First complete set of nuclear anchor load–displacement data and its evaluation ever. • Demonstration of robust test behavior of a qualified post-installed anchor product. - Abstract: In nuclear power plants (NPPs), post-installed anchors are widely used for structural and non-structural connections to concrete. In many countries, anchor products employed for safety relevant applications have to be approved by the authorities. For the high safety standards in force for NPPs, special requirements have to be met to allow for extreme design situations. This paper presents an experimental test program conducted to evaluate the performance of anchors according to the German Guideline for Anchorages in Nuclear Power Plants and Nuclear Technology Installations (DIBt KKW Leitfaden, 2010). After a brief introduction to anchor behavior and the regulative context, the results of tension and shear tests carried out on undercut anchors are discussed. Robust load capacities and relatively small displacements determined for demanding load and crack cycling tests demonstrated the suitability of anchors qualified according to a state-of-the-art qualification guideline

Age and Sex Effects in Anchoring Vignette Studies: Methodological and Empirical Contributions

Directory of Open Access Journals (Sweden)

Hanna Grol-Prokopczyk

2013-04-01

Full Text Available Anchoring vignettes are an increasingly popular tool for identifying and correcting for group differences in use of subjective ordered response categories. However, existing techniques to maximize response consistency (use of the same standards for self-ratings as for vignette-ratings, which center on matching vignette characters’ demographic characteristics to respondents’ own characteristics, appear at times to be ineffective or to pose interpretive difficulties. Specifically, respondents often appear to neglect instructions to treat vignette characters as age peers. Furthermore, when vignette characters’ sex is matched to respondents’ sex, interpretation of sex differences in rating style is rendered problematic. This study applies two experimental manipulations to a national American sample (n=1,765 to clarify best practices for enhancing response consistency. First, an analysis of two methods of highlighting vignette characters’ age suggests that both yield better response consistency than previous, less prominent means. Second, a comparison of ratings of same- and opposite-sex vignette characters suggests that, with avoidable exceptions, the sex of the respondent rather than of the vignette character drives observed sex differences in rating style. Implications for interpretation and design of anchoring vignette studies are discussed. Findings also show significant sex, educational, and racial/ethnic differences in styles of rating health, and racial/ethnic differences in styles of rating political efficacy. These findings underscore the incomparability of unadjusted subjective self-ratings across demographic groups.

Arthroscopic knotless anchor repair of triangular fibrocartilage in distal radius fracture.

Science.gov (United States)

García-Ruano, Á A; Najarro-Cid, F; Jiménez-Martín, A; Gómez de los Infantes-Troncoso, J G; Sicre-González, M

2015-01-01

Lesions of triangular fibrocartilage (TFC) are associated with distal radioulnar joint instability. Arthroscopic treatment of these lesions improves functional outcome of affected patients. The aim of the present work is to evaluate functional and occupational outcome of TCF repair using an arthroscopic knotless anchor device in patients with associated distal radius fracture. An observational, descriptive study was carried out between November 2011 and January 2014 including 21 patients with distal radius fracture and Palmer 1B lesions of TCF (Atzei class 2 and 3) that were treated by arthroscopic knotless anchor (PopLok® 2,8mm, ConMed, USA). Mean follow-up was 18 months. Functional (Mayo Wrist Score) and occupational outcome results were analyzed. Mean age of the group was 43.0±8.8 years, with 19% of the patients being female. There was an associated scapholunate lesion in 5 cases. Functional results reached a mean of 83.4±16.1 points onMayo Wrist Score. Mean sick-leave time was 153.16±48.5 days. Complete occupational reintegration was reached in 89.5% of cases. There were no postoperative complications. Arthroscopic knotless anchor repair of 1B TFC tears is a minimally invasive method of treatment that improves tension of fixation, avoiding subsequent loosen, in our experience, with few complications and good functional and occupational results. Copyright © 2014 SECOT. Published by Elsevier Espana. All rights reserved.

Anchorage Behaviors of Frictional Tieback Anchors in Silty Sand

Science.gov (United States)

Hsu, Shih-Tsung; Hsiao, Wen-Ta; Chen, Ke-Ting; Hu, Wen-Chi; Wu, Ssu-Yi

2017-06-01

Soil anchors are extensively used in geotechnical applications, most commonly serve as tieback walls in deep excavations. To investigate the anchorage mechanisms of this tieback anchor, a constitutive model that considers both strain hardening and softening and volume dilatancy entitled SHASOVOD model, and FLAC3D software are used to perform 3-D numerical analyses. The results from field anchor tests are compared with those calculated by numerical analyses to enhance the applicability of the numerical method. After the calibration, this research carried out the parameter studies by numerical analyses. The numerical results reveal that whether the yield of soil around an anchor develops to ground surface and/or touches the diaphragm wall depending on the overburden depth H and the embedded depth Z of an anchor, this study suggests the minimum overburden and embedded depths to avoid the yield of soils develop to ground surface and/or touch the diaphragm wall. When the embedded depth, overburden depth or fixed length of an anchor increases, the anchorage capacity also increases. Increasing fixed length should be the optimum method to increase the anchorage capacity for fixed length less than 20m. However, when the fixed length of an anchor exceeds 30 m, the increasing rate of anchorage capacity per fixed length decreases, and progressive yield occurs obviously between the fixed length and surrounding soil.

Constrained Active Learning for Anchor Link Prediction Across Multiple Heterogeneous Social Networks.

Science.gov (United States)

Zhu, Junxing; Zhang, Jiawei; Wu, Quanyuan; Jia, Yan; Zhou, Bin; Wei, Xiaokai; Yu, Philip S

2017-08-03

Nowadays, people are usually involved in multiple heterogeneous social networks simultaneously. Discovering the anchor links between the accounts owned by the same users across different social networks is crucial for many important inter-network applications, e.g., cross-network link transfer and cross-network recommendation. Many different supervised models have been proposed to predict anchor links so far, but they are effective only when the labeled anchor links are abundant. However, in real scenarios, such a requirement can hardly be met and most anchor links are unlabeled, since manually labeling the inter-network anchor links is quite costly and tedious. To overcome such a problem and utilize the numerous unlabeled anchor links in model building, in this paper, we introduce the active learning based anchor link prediction problem. Different from the traditional active learning problems, due to the one-to-one constraint on anchor links, if an unlabeled anchor link a = ( u , v ) is identified as positive (i.e., existing), all the other unlabeled anchor links incident to account u or account v will be negative (i.e., non-existing) automatically. Viewed in such a perspective, asking for the labels of potential positive anchor links in the unlabeled set will be rewarding in the active anchor link prediction problem. Various novel anchor link information gain measures are defined in this paper, based on which several constraint active anchor link prediction methods are introduced. Extensive experiments have been done on real-world social network datasets to compare the performance of these methods with state-of-art anchor link prediction methods. The experimental results show that the proposed Mean-entropy-based Constrained Active Learning (MC) method can outperform other methods with significant advantages.

Effects of the anchor system on postural control in older Adults

Directory of Open Access Journals (Sweden)

Eliane Mauerberg de Castro

2012-03-01

Full Text Available Falls are common during aging, and can have drastic consequences. Within this context, maintaining the ability to balance plays an essential role in enabling older adults to continue to perform their daily activities. Therefore, the use of interventional and treatment tools for development of balance becomes essential. The objective of this study was to analyze the anchor system as a potential tool for decreasing body sway in older and young adults. Older adults had more postural sway than their young counterparts. The absence of visual information led to larger instability in both groups. The anchor system improved postural stability of both groups. Thus, it may be a useful tool for posture stabilization in old and young adults.

Rational use of anchor pile material of the thin retaining walls

Directory of Open Access Journals (Sweden)

Yushkov Boris Semenovich

2014-12-01

Full Text Available The article considers the urgency of application of the reinforced concrete anchor piles in the constructions of retaining structures associated with the possibility of establishing rigid joint of element interface and more durable pile constructions in the soil. The features of the inclined anchor piles work as a part of sheet-pile retaining walls are noted. There was performed a study of the stress-strain state of the inclined reinforced concrete anchor piles of the thin sheet-pile wall with the reinforced concrete face members of T-section, combined with piles by a longitudinal beam. The authors consider a constructive scheme of retaining structure and list the applied loads. The efforts in the anchor piles were determined. The bending-moment curves show the character of the force distribution along the pile. A form of the pile ensuring the rational distribution of material along the pile is presented. The distribution of efforts along the length and effect of filling on its operation in the soil were accepted as the criteria of construction solution for a pile. The substantiation of the proposed design of pile is presented in terms of its stress-strain state and the rational use of material. The authors made conclusions on the reasonability of adopted design solutions associated with an increase in the flexural strength of pile, increment of the ultimate pullout capacity, stability improvement, effective use of backfill and exception of the «out of operation» areas of the pile.

The Primary Stability of a Bioabsorbable Poly-L-Lactic Acid Suture Anchor for Rotator Cuff Repair Is Not Improved with Polymethylmethacrylate or Bioabsorbable Bone Cement Augmentation.

Science.gov (United States)

Güleçyüz, Mehmet F; Kraus-Petersen, Michael; Schröder, Christian; Ficklscherer, Andreas; Wagenhäuser, Markus U; Braun, Christian; Müller, Peter E; Pietschmann, Matthias F

2018-02-01

The incidence of osteoporosis and rotator cuff tears increases with age. Cement augmentation of bones is an established method in orthopedic and trauma surgery. This study analyses if polymethylmethacrylate or bioabsorbable cement can improve the primary stability of a bioabsorbable suture anchor in vitro in comparison to a non-augmented suture anchor in osteoporotic human humeri. The trabecular bone mineral density was measured to ensure osteopenic human specimens. Then the poly-l-lactic acid Bio-Corkscrew® FT was implanted in the greater tuberosity footprint with polymethylmethacrylate Refobacin® cement augmentation ( n  = 8), with Cerament™ Bone Void Filler augmentation ( n  = 8) and without augmentation ( n  = 8). Using a cyclic testing protocol, the failure loads, system displacement, and failure modes were recorded. The Cerament™ augmented Bio-Corkscrew® FT yielded the highest failure loads (206.7 N), followed by polymethylmethacrylate Refobacin® augmentation (206.1 N) and without augmentation (160.0 N). The system displacement was lowest for Cerament™ augmentation (0.72 mm), followed by polymethylmethacrylate (0.82 mm) and without augmentation (1.50 mm). Statistical analysis showed no significant differences regarding the maximum failure loads ( p  = 0.1644) or system displacement ( p  = 0.4199). The main mode of failure for all three groups was suture slippage. The primary stability of the Bio-Corkscrew® FT is not influenced by bone cement augmentation with polymethylmethacrylate Refobacin® or with bioabsorbable Cerament™ in comparison to the non-cemented anchors. The cement augmentation of rotator cuff suture anchors in osteoporotic bones remains questionable since biomechanical tests show no significant advantage.

Link Anchors in Images: Is there Truth?

NARCIS (Netherlands)

Aly, Robin; McGuinness, Kevin; Kleppe, Martijn; Ordelman, Roeland J.F.; O'Connor, Noel; de Jong, Franciska M.G.

2012-01-01

While automatic linking in text collections is well understood, little is known about links in images. In this work, we investigate two aspects of anchors, the origin of a link, in images: 1) the requirements of users for such anchors, e.g. the things users would like more information on, and 2)

ANCHORING IN THE POLITICAL AND ECONOMIC MARKETING

Directory of Open Access Journals (Sweden)

Tatyana L. Shklyar

2015-01-01

Full Text Available The main purpose of marketing, both ineconomy and in politics is to attract themaximum number of customers or voters, maximizing customer satisfaction and ,ideally, improve the quality of life.The author, in various aspects, thetechnology of anchoring used in NLP, to attract customers and voters, both in the economy and in politics.In different examples demonstrate theoverall impact on the psychology of the consumer. Separating policy and the economy, marketers are missing something. The author proposes to look at how psychologicalanchors affect these two, at fi rst glance, different vector.

Comparison of bone tunnel and suture anchor techniques in the modified Broström procedure for chronic lateral ankle instability.

Science.gov (United States)

Hu, Chang-Yong; Lee, Keun-Bae; Song, Eun-Kyoo; Kim, Myung-Sun; Park, Kyung-Soon

2013-08-01

The modified Broström procedure is frequently used to treat chronic lateral ankle instability. There are 2 common methods of the modified Broström procedure, which are the bone tunnel and suture anchor techniques. To compare the clinical outcomes of the modified Broström procedure using the bone tunnel and suture anchor techniques. Cohort study; Level of evidence, 2. Eighty-one patients (81 ankles) treated with the modified Broström procedure for chronic lateral ankle instability constituted the study cohort. The 81 ankles were divided into 2 groups, namely, a bone tunnel technique (BT group; 40 ankles) and a suture anchor technique (SA group; 41 ankles). The Karlsson score, American Orthopaedic Foot and Ankle Society (AOFAS) ankle-hindfoot score, anterior talar translation, and talar tilt angle were used to evaluate clinical and radiographic outcomes. The BT group consisted of 32 men and 8 women with a mean age of 34.8 years at surgery and a mean follow-up duration of 34.2 months. The SA group consisted of 33 men and 8 women with a mean age of 33.3 years at surgery and a mean follow-up duration of 32.8 months. Mean Karlsson scores improved significantly from 57.0 points preoperatively to 94.9 points at final follow-up in the BT group and from 59.9 points preoperatively to 96.4 points at final follow-up in the SA group. Mean AOFAS scores also improved from 64.2 points preoperatively to 97.8 points at final follow-up in the BT group and from 70.3 points preoperatively to 97.4 points at final follow-up in the SA group. Mean anterior talar translations in the BT group and SA group improved from 9.0 mm and 9.2 mm preoperatively to 6.5 mm and 6.8 mm at final follow-up, respectively. Mean talar tilt angles were 12.0° in the BT group and 12.5° in the SA group preoperatively and 8.8° at final follow-up for both groups. No significant differences were found between the 2 groups in terms of the Karlsson score, AOFAS score, anterior talar translation, and talar tilt

Arthroscopic repair of lateral ankle ligament complex by suture anchor.

Science.gov (United States)

Wang, Jingwei; Hua, Yinghui; Chen, Shiyi; Li, Hongyun; Zhang, Jian; Li, Yunxia

2014-06-01

Arthroscopic repair of the lateral ligament complex with suture anchors is increasingly used to treat chronic ankle instability (CAI). Our aims are (1) to analyze and evaluate the literature on arthroscopic suture anchor repair of the anterior talofibular ligament and (2) to conduct a systematic review of the clinical evidence on the reported outcomes and complications of treating CAI with this technique. We performed a systematic review of the literature using PubMed, Ovid, Elsevier ScienceDirect, Web of Science-Conference Proceedings Citation Index, and the Cochrane Database of Systematic Reviews from 1987 to September 2013. Clinical studies using the arthroscopic suture anchor technique to treat CAI were included. Outcome measures consisted of clinical assessment of postoperative ligament stability and complications. In addition, the methodologic quality of the included studies was assessed by use of the modified Coleman Methodology Score. After reviewing 371 studies, we identified 6 studies (5 retrospective case series and 1 prospective case series, all Level IV) that met the inclusion criteria, with a mean Coleman Methodology Score of 71.8 ± 7.52 (range, 63 to 82). In these studies 178 patients (179 ankles) underwent arthroscopic suture anchor repair of the anterior talofibular ligament with a mean follow-up period of 38.9 months (range, 6 to 117.6 months). All patients were reported to have subjective improvement of their ankle instability, with complications in 31 cases. Studies of arthroscopic suture anchor technique to treat CAI are sparse, with moderate mean methodologic quality. The included studies suggest that the arthroscopic technique is a feasible procedure to restore ankle stability; however, on the basis of our review, this technique seems to be associated with a relatively high complication rate. Extensive cadaveric studies, clinical trials, and comparative studies comparing arthroscopic and open repair should be performed in the future. Level

The Effect of Mini and Midi Anchor Tests on Test Equating

Science.gov (United States)

Arikan, Çigdem Akin

2018-01-01

The main purpose of this study is to compare the test forms to the midi anchor test and the mini anchor test performance based on item response theory. The research was conducted with using simulated data which were generated based on Rasch model. In order to equate two test forms the anchor item nonequivalent groups (internal anchor test) was…

Use of the ROC anchor in foot and ankle surgery. A retrospective study.

Science.gov (United States)

Kuwada, G T

1999-05-01

A retrospective study was conducted on the use of the ROC (Radial Osteo Compression) soft-tissue anchor in foot and ankle surgery. This article describes how the anchor is deployed, problematic aspects of using the anchor, and complications and success rates associated with the anchor in ankle stabilizations, posterior tibial tendon reconstruction, peroneus brevis tendon reconstruction after fracture of the base of the fifth metatarsal, and detachment and reattachment of the Achilles tendon. The ROC anchor consists of the anchor with nonabsorbable suture attached to the shaft, the deployment handle, and drill bits. The anchor and shaft are snapped into the deployment handle and inserted into the drill hole. Compression of the trigger deploys the anchor into the hole. The ROC anchor was found to be reliable, useful, and relatively easy to deploy, with outcomes similar to those of other soft-tissue anchors.

Anchoring Proteins as Regulators of Signaling Pathways

Science.gov (United States)

Perino, Alessia; Ghigo, Alessandra; Scott, John D.; Hirsch, Emilio

2012-01-01

Spatial and temporal organization of signal transduction is coordinated through the segregation of signaling enzymes in selected cellular compartments. This highly evolved regulatory mechanism ensures the activation of selected enzymes only in the vicinity of their target proteins. In this context, cAMP-responsive triggering of protein kinase A is modulated by a family of scaffold proteins referred to as A-kinase anchoring proteins. A-kinase anchoring proteins form the core of multiprotein complexes and enable simultaneous but segregated cAMP signaling events to occur in defined cellular compartments. In this review we will focus on the description of A-kinase anchoring protein function in the regulation of cardiac physiopathology. PMID:22859670

On the Robustness of Anchoring Effects in WTP and WTA Experiments

OpenAIRE

Drew Fudenberg; David K Levine; Zacharias Maniadis

2010-01-01

We reexamine the effects of the anchoring manipulation of Ariely, Loewenstein, and Prelec (2003) on the evaluation of common market goods and find very weak anchoring effects. We perform the same manipulation on the evaluation of binary lotteries, and find no anchoring effects at all. This suggests limits on the robustness of anchoring effects. (JEL C91, D12, D44)

Career Paths, Images and Anchors: A Study with Brazilian Professionals

Science.gov (United States)

Kilimnik, Zelia Miranda; de Oliveira, Luiz Claudio Vieira; Sant'anna, Anderson De Souza; Barros, Delba Teixeira Rodrigues

2011-01-01

This article analyses career anchors changes associated to images and professionals trajectories. Its main question: Do anchors careers change through time? We conducted twelve interviews involving professionals from the Administration Area, applying Schein's Career Anchors Inventory (1993). We did the same two years later. In both of them, the…

Stone anchors of India: Findings, classification and significance.

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

Various types of stone anchors have been observed during inshore and offshore explorations along the east and west coasts of India. The earliest stone anchors of India have been recorded from the Harappan sites (3rd millennium BC), but their shape...

Investigation of suction anchor pullout capacity under undrained conditions

OpenAIRE

Jarand, Pollestad

2015-01-01

Master's thesis in Offshore technology Floating units are dependent on reliable mooring systems to ensure safety during marine operations. Suction anchors have proved to be a technologically viable and cost-effective concept. They are capable of precision installation, re-use, and provide large resistive capacity. This thesis investigates load capacity and failure modes of suction anchors subjected to vertical, horizontal (lateral), and incline loading. Suction anchor design co...

Pyramidal anchor stone from Baga waters of Goa, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.

. Pyramidal anchor stones have an apex hole which goes up to the round hole, however Goa anchor stone has no such perforation, but, instead has a rectangular cutting on the apex. The anchor stone is compared with Greek pyramidal anchor stones, and probably...

Mutational analysis of the glycosylphosphatidylinositol (GPI) anchor pathway demonstrates that GPI-anchored proteins are required for cell wall biogenesis and normal hyphal growth in Neurospora crassa.

Science.gov (United States)

Bowman, Shaun M; Piwowar, Amy; Al Dabbous, Mash'el; Vierula, John; Free, Stephen J

2006-03-01

Using mutational and proteomic approaches, we have demonstrated the importance of the glycosylphosphatidylinositol (GPI) anchor pathway for cell wall synthesis and integrity and for the overall morphology of the filamentous fungus Neurospora crassa. Mutants affected in the gpig-1, gpip-1, gpip-2, gpip-3, and gpit-1 genes, which encode components of the N. crassa GPI anchor biosynthetic pathway, have been characterized. GPI anchor mutants exhibit colonial morphologies, significantly reduced rates of growth, altered hyphal growth patterns, considerable cellular lysis, and an abnormal "cell-within-a-cell" phenotype. The mutants are deficient in the production of GPI-anchored proteins, verifying the requirement of each altered gene for the process of GPI-anchoring. The mutant cell walls are abnormally weak, contain reduced amounts of protein, and have an altered carbohydrate composition. The mutant cell walls lack a number of GPI-anchored proteins, putatively involved in cell wall biogenesis and remodeling. From these studies, we conclude that the GPI anchor pathway is critical for proper cell wall structure and function in N. crassa.

Peptide-Mediated Liposome Fusion: The Effect of Anchor Positioning

Directory of Open Access Journals (Sweden)

Niek S. A. Crone

2018-01-01

Full Text Available A minimal model system for membrane fusion, comprising two complementary peptides dubbed “E” and “K” joined to a cholesterol anchor via a polyethyleneglycol spacer, has previously been developed in our group. This system promotes the fusion of large unilamellar vesicles and facilitates liposome-cell fusion both in vitro and in vivo. Whilst several aspects of the system have previously been investigated to provide an insight as to how fusion is facilitated, anchor positioning has not yet been considered. In this study, the effects of placing the anchor at either the N-terminus or in the center of the peptide are investigated using a combination of circular dichroism spectroscopy, dynamic light scattering, and fluorescence assays. It was discovered that anchoring the “K” peptide in the center of the sequence had no effect on its structure, its ability to interact with membranes, or its ability to promote fusion, whereas anchoring the ‘E’ peptide in the middle of the sequence dramatically decreases fusion efficiency. We postulate that anchoring the ‘E’ peptide in the middle of the sequence disrupts its ability to form homodimers with peptides on the same membrane, leading to aggregation and content leakage.

Testing methods of steel wi re ropes at the anchor

Directory of Open Access Journals (Sweden)

Stanislav Kropuch

2012-12-01

Full Text Available The present paper introduces an application of the acoustic andthermographic method in the defectoscopic testing of immobilesteel wire ropes at the most critical point, the anchor. Firstmeasurements and their results by these new defectoscopic methodsare shown. In defectoscopic tests at the anchor, the widelyused magnetic method gives unreliable results, and therefore presentsa problem for steel wire defectoscopy. Application of the two new methods in the steel wire defectoscopy at the anchor point will enableincreased safety measures at the anchor of steel wire ropes in bridge, roof, tower and aerial cable lift constructions.

Assessing tether anchor labeling and usability in pickup trucks.

Science.gov (United States)

Klinich, Kathleen D; Manary, Miriam A; Malik, Laura A; Flannagan, Carol A; Jermakian, Jessica S

2018-04-03

The objective of this study was to investigate vehicle factors associated with child restraint tether use and misuse in pickup trucks and evaluate 4 labeling interventions designed to educate consumers on proper tether use. Volunteer testing was performed with 24 subjects and 4 different pickup trucks. Each subject performed 8 child restraint installations among the 4 pickups using 2 forward-facing restraints: a Britax Marathon G4.1 and an Evenflo Triumph. Vehicles were selected to represent 4 different implementations of tether anchors among pickups: plastic loop routers (Chevrolet Silverado), webbing routers (Ram), back wall anchors (Nissan Frontier), and webbing routers plus metal anchors (Toyota Tundra). Interventions included a diagram label, Quick Response (QR) Code linked to video instruction, coordinating text label, and contrasting text tag. Subjects used the child restraint tether in 93% of trials. However, tether use was completely correct in only 9% of trials. An installation was considered functional if the subject attached the tether to a tether anchor and had a tight installation (ignoring routing and head restraint position); 28% of subjects achieved a functional installation. The most common installation error was attaching the tether hook to the anchor/router directly behind the child restraint (near the top of the seatback) rather than placing the tether through the router and attaching it to the anchor in the adjacent seating position. The Nissan Frontier, with the anchor located on the back wall of the cab, had the highest rate of correct installations but also had the highest rate of attaching the tether to components other than the tether anchor (seat adjustor, child restraint storage hook, around head restraint). None of the labeling interventions had a significant effect on correct installation; not a single subject scanned the QR Code to access the video instruction. Subjects with the most successful installations spent extensive time

Anchoring submersible ultrasonic receivers in river channels with stable substrate

Science.gov (United States)

Bettoli, Phillip William; Scholten, G.D.; Hubbs, D.

2010-01-01

We developed an anchoring system for submersible ultrasonic receivers (SURs) that we placed on the bottom of the riverine reaches of three main-stem reservoirs in the upper Tennessee River. Each anchor consisted of a steel tube (8.9 x 35.6 cm) welded vertically to a round plate of steel (5.1 x 40.6 cm). All seven SURs and their 57-kg anchors were successfully deployed and retrieved three times over 547 d by a dive team employing surface air-breathing equipment and a davit-equipped boat. All of the anchors and their SURs remained stationary over two consecutive winters on the hard-bottom, thalweg sites where they were deployed. The SUR and its anchor at the most downriver site experienced flows that exceeded 2,100 m(3)/s and mean water column velocities of about 0.9 m/s.

Self-Assembled Monolayers on Gold of β-Cyclodextrin Adsorbates with Different Anchoring Groups

NARCIS (Netherlands)

Méndez Ardoy, Alejandro; Steentjes, Tom; Kudernac, Tibor; Huskens, Jurriaan

2014-01-01

We designed multivalent β-cyclodextrin-based adsorbates bearing different anchoring groups aiming to yield stable monolayers with improved packing and close contact of the cavity to the gold surface. Toward this end the primary rim of the β-cyclodextrin was decorated with several functional groups,

Archaeometallurgical investigation of the iron anchor from the Tantura F shipwreck

Energy Technology Data Exchange (ETDEWEB)

Aronson, A. [Faculty of Engineering, Tel Aviv University, Ramat Aviv 69978 (Israel); Ashkenazi, D., E-mail: dana@eng.tau.ac.il [Faculty of Engineering, Tel Aviv University, Ramat Aviv 69978 (Israel); Barkai, O.; Kahanov, Y. [Leon Recanati Institute for Maritime Studies, University of Haifa, Haifa 31905 (Israel)

2013-04-15

The Tantura F shipwreck was a coaster or a fishing vessel about 15.7 m long, discovered in the Dor/Tantura lagoon, Israel in 1995. It was dated to between the mid-7th and the end of the 8th centuries CE. Among the finds excavated were two T-shaped type iron anchors. Of the two anchors, one (anchor A) was thoroughly studied by archaeometallurgical methods in order to identify forge-welding lines, to determine the welding quality and to understand the manufacturing technology. The examinations included X-ray radiography, XRF analysis, optical microscopy, SEM/EDS observation and analysis, OES analysis and microhardness tests. The investigation included characterization of the composition, microstructure, thermal treatments, forge-welding junctions and slag analysis. The results revealed a heterogeneous microstructure, rich in glassy, fayalite and wüstite slag. Iron based phases included ferrite, pearlite, cementite and Widmanstätten plates, all typical to wrought iron. The forge-welds of Anchor A were located. Each arm was made of one piece, weighing about 2.5–3 kg and the shank was made of a few 1.5–2 kg pieces. The second anchor (anchor B) was only briefly examined visually and with a few radiographs, which support the results from anchor A. The research results revealed significant information about T-shaped anchors and their manufacturing process, including hot-working processes without any additional heat treatments, and folding techniques. The microstructure was similar to other ancient simple tools such as saws, sickles, axes and mortise chisels, and though the technology to make complicated structures and objects, such as swords, existed at that time, the anchors did not require this sophistication; thus simpler techniques were used, presumably because they were more cost-effective. - Highlights: ► Tantura F was a coaster dated to mid-7th–end-8th centuries. ► Two iron anchors were discovered at the Tantura F shipwreck-site. ► Anchor A was

Do budget balance rules anchor budget balance expectations? -- Some international evidence

OpenAIRE

Rülke, Jan-Christoph; Frenkel, Michael; Lis, Eliza

2013-01-01

This is the first study that analyzes whether budget balance expectations are anchored and whether budget balance rules effectively anchor expectations. To this end, we use a unique data set which covers budget balance expectations in 17 countries that implemented a budget balance rules. While our results are mixed concerning the general impact of budget balance rules on anchoring expectations, we do find that specific features of budget balance rules are important to successfully anchor budg...

Ultimate load capacities of expansion anchor bolts

International Nuclear Information System (INIS)

Czarnecki, R.M.; Manrique, M.A.; Samaddar, S.K.

1993-01-01

A summary of available experimental expansion anchor bolt test data is presented. These data were collected as part of programs by the nuclear industry to address generic issues related to verification of seismic adequacy of equipment in nuclear power plants. Some of the data presented are suitable for use in seismic probabilistic risk assessments. For example, mean values of ultimate strength, along with their standard deviation and coefficients of variation, for a range of most typical expansion anchor bolt sizes are presented. Effects of interaction between shear and tension, edge distance, spacing, and cracking of the concrete are presented in a manner that is more suitable for use in deterministic evaluations. Related industry programs to derive anchor bolt capacities are briefly discussed. Recommendations for areas of further investigation are also presented

[Treatment of calcaneal avulsion fractures with twinfix suture anchors fixation].

Science.gov (United States)

Zhao, Bin-xiu; Wang, Kun-zheng; Wang, Chun-sheng; Xie, Yue; Dai, Zhi-tang; Liu, Gang; Liu, Wei-dong

2011-06-01

For the calcaneal avulsion fracture, the current method is more commonly used screws or Kirschner wire to fix fracture fragment. This article intended to explore the feasibility and clinical efficacy for the treatment of avulsion fractures with TwinFix suture anchors. From July 2007 to November 2010, 21 patients were reviewed, including 15 males and 6 females, ranging in age from 49 to 65 years,with a mean of 58.7 years. Twelve patients had nodules in the right heel and 9 patients had nodules in the left heel. All the patients had closed fractures. The typical preoperative symptoms of the patients included pain in the upper heel and weak in heel lift. Body examination results: palpable sense of bone rubbing in the back of the heel, and swelling in the heel. Surgery treatment with TwinFix suture anchors performed as follows : to fix TwinFix suture anchors into the calcaneal body, then to drill the fracture block, to make the double strand suture through the fracture holes, to knot the suture eachother to fix the block, and to use stitch to fix the remaining suture in the Achilles tendon in order to improve the block fixation. The criteria of the AOFAS Foot and Ankle Surgery by the United States Association of ankle-rear foot functional recovery was used to evaluate the Achilles tendon. Total average score was (95.5 +/- 3.12) points, including pain items of(38.5 +/- 2.18) points,the average score of functional items of (49.5 +/- 3.09) points,and power lines of 10 points in all patients. Twenty-one patients got an excellent result, 16 good and 5 poor. The methods of treatment for the calcaneal avulsion fractures with TwinFix suture anchors is a simple operation, and have excellent clinical effect, which is worthy of promotion.

Novel applications for glycosylphosphatidylinositol-anchored proteins in pharmaceutical and industrial biotechnology.

Science.gov (United States)

Müller, Günter

2011-04-01

Glycosylphosphatidylinositol (GPI)-anchored proteins have been regarded as typical cell surface proteins found in most eukaryotic cells from yeast to man. They are embedded in the outer plasma membrane leaflet via a carboxy-terminally linked complex glycolipid GPI structure. The amphiphilic nature of the GPI anchor, its compatibility with the function of the attached protein moiety and the capability of GPI-anchored proteins for spontaneous insertion into and transfer between artificial and cellular membranes initially suggested their potential for biotechnological applications. However, these expectations have been hardly fulfilled so far. Recent developments fuel novel hopes with regard to: (i) Automated online expression, extraction and purification of therapeutic proteins as GPI-anchored proteins based on their preferred accumulation in plasma membrane lipid rafts, (ii) multiplex custom-made protein chips based on GPI-anchored cell wall proteins in yeast, (iii) biomaterials and biosensors with films consisting of sets of distinct GPI-anchored binding-proteins or enzymes for sequential or combinatorial catalysis, and (iv) transport of therapeutic proteins across or into relevant tissue cells, e.g., enterocytes or adipocytes. Latter expectations are based on the demonstrated translocation of GPI-anchored proteins from plasma membrane lipid rafts to cytoplasmic lipid droplets and eventually further into microvesicles which upon release from donor cells transfer their GPI-anchored proteins to acceptor cells. The value of these technologies, which are all based on the interaction of GPI-anchored proteins with membranes and surfaces, for the engineering, production and targeted delivery of biomolecules for a huge variety of therapeutic and biotechnological purposes should become apparent in the near future.

Do anchor investors create value for initial public offerings? An empirical investigation

Directory of Open Access Journals (Sweden)

Seshadev Sahoo

2017-12-01

Full Text Available The concept of anchor investors was introduced by the market regulator, Securities Exchange Board of India (SEBI, to bring transparency in the book building mechanism. We examine anchor investors' investment in initial public offerings (IPOs to determine how they create value for issuing firms and participating investors. Using a database of 135 IPOs issued in the Indian market through book building mechanism during 2009–2014, we find that anchor investors' investment in IPOs reduces underpricing. Larger subscription from retail investors for anchor-supported IPOs indicates that anchor investors' participation is viewed as a credible attestation of quality of the issue. We document that anchor-supported IPOs are more liquid and less volatile in the short run. We also find that by controlling for other factors such as offer size, subscription rate and age of the firm, a part of the underpricing is reduced by anchor investors.

Considerations on the design of through-wall anchors

International Nuclear Information System (INIS)

Ricklefs, Ulf

2012-01-01

Connections to existing buildings are often the most difficult planning challenge for the realization of construction measures in case of piping system replacements in nuclear power plants. This is due to restricted space or limited load reserves of the building structure. Usually the realization of support connections to the existing buildings is achieved by anchor bolts. But in critical cases the preferred alternative solution uses through-wall anchors. Up to now uniform assessment thresholds are not available, no technical guidelines or regulations for construction variants exist. Through-wall anchors allow significantly higher load capacities for tensile and shear loads but require enhanced planning and realization efforts.

Bonding, Bridging, and Linking Social Capital and Self-Rated Health among Chinese Adults: Use of the Anchoring Vignettes Technique.

Directory of Open Access Journals (Sweden)

He Chen

Full Text Available Three main opposing camps exist over how social capital relates to population health, namely the social support perspective, the inequality thesis, and the political economy approach. The distinction among bonding, bridging, and linking social capital probably helps close the debates between these three camps, which is rarely investigated in existing literatures. Moreover, although self-rated health is a frequently used health indicator in studies on the relationship between social capital and health, the interpersonal incomparability of this measure has been largely neglected. This study has two main objectives. Firstly, we aim to investigate the relationship between bonding, bridging, and linking social capital and self-rated health among Chinese adults. Secondly, we aim to improve the interpersonal comparability in self-rated health measurement. We use data from a nationally representative survey in China. Self-rated health was adjusted using the anchoring vignettes technique to improve comparability. Two-level ordinal logistic regression was performed to model the association between social capital and self-rated health at both individual and community levels. The interaction between residence and social capital was included to examine urban/rural disparities in the relationship. We found that most social capital indicators had a significant relationship with adjusted self-rated health of Chinese adults, but the relationships were mixed. Individual-level bonding, linking social capital, and community-level bridging social capital were positively related with health. Significant urban/rural disparities appeared in the association between community-level bonding, linking social capital, and adjusted self-rated health. For example, people living in communities with higher bonding social capital tended to report poorer adjusted self-rated health in urban areas, but the opposite tendency held for rural areas. Furthermore, the comparison between

Bonding, Bridging, and Linking Social Capital and Self-Rated Health among Chinese Adults: Use of the Anchoring Vignettes Technique.

Science.gov (United States)

Chen, He; Meng, Tianguang

2015-01-01

Three main opposing camps exist over how social capital relates to population health, namely the social support perspective, the inequality thesis, and the political economy approach. The distinction among bonding, bridging, and linking social capital probably helps close the debates between these three camps, which is rarely investigated in existing literatures. Moreover, although self-rated health is a frequently used health indicator in studies on the relationship between social capital and health, the interpersonal incomparability of this measure has been largely neglected. This study has two main objectives. Firstly, we aim to investigate the relationship between bonding, bridging, and linking social capital and self-rated health among Chinese adults. Secondly, we aim to improve the interpersonal comparability in self-rated health measurement. We use data from a nationally representative survey in China. Self-rated health was adjusted using the anchoring vignettes technique to improve comparability. Two-level ordinal logistic regression was performed to model the association between social capital and self-rated health at both individual and community levels. The interaction between residence and social capital was included to examine urban/rural disparities in the relationship. We found that most social capital indicators had a significant relationship with adjusted self-rated health of Chinese adults, but the relationships were mixed. Individual-level bonding, linking social capital, and community-level bridging social capital were positively related with health. Significant urban/rural disparities appeared in the association between community-level bonding, linking social capital, and adjusted self-rated health. For example, people living in communities with higher bonding social capital tended to report poorer adjusted self-rated health in urban areas, but the opposite tendency held for rural areas. Furthermore, the comparison between multivariate analyses

Anchor enhanced capsulorraphy in bunionectomies using an L-shaped capsulotomy.

Science.gov (United States)

Gould, John S; Ali, Sheriff; Fowler, Rachel; Fleisig, Glenn S

2003-01-01

The objective of this study was to investigate potential benefit of a suture anchor-enhanced capsulorraphy in the early maintenance of correction in bunionectomies. We compared, retrospectively, in successive series, the loss of correction of the Hallux Valgus (HV) and intermetatarsal (IM) angle, in those repaired with an L-shaped capsulorraphy enhanced with anchors to those without. Intraoperative and second week postoperative simulated weightbearing anterior posterior (AP) X-rays were used to evaluate results. By using only intraoperative and early postoperative X-rays, we should have effectively eliminated extraneous factors that might have influenced our results. A Total of 106 cases were investigated, 65 of which were repaired using anchors, the remaining 41 without. In the anchor group, 38 underwent a proximal metatarsal concentric shelf osteotomy (CSO)/modified McBride procedure, while the remaining 27 had a distal Chevron correction. In the without-anchor group, 21 had a CSO/modified McBride procedure while 20 underwent the Chevron procedure. In the without-anchor group, the average HV and IM loss of correction was 4.60 degrees (range, -2 to 21 degrees) and 0.6 degrees (range, -1 to 9 degrees) respectively. In the anchor group, the corresponding loss was 2.8 degrees (range, -3 to 17 degrees) and 0.6 degrees (range, -2 to 14 degrees) respectively. These results, when statistically analyzed, demonstrated that while the IM angle change was not statistically significant, the HV angle change was statistically significant, implying that the anchor plays a significant role in maintaining the surgical correction in both the distal Chevron and CSO/ modified McBride bunionectomies.

Stone anchors from the Okhamandal region, Gujarat Coast, India

Digital Repository Service at National Institute of Oceanography (India)

Sundaresh; Gaur, A.S.; Gudigar, P.; Tripati, S.; Vora, K.H.; Bandodkar, S.N.

During marine archaeological explorations since 1983, off Dwarka, a large number of stone anchors were discovered and dated to 1400 BC, comparing with anchors found in Mediterranean waters. In recent archaeological explorations off Dwarka, Bet...

Functionalized Nanostructures: Redox-Active Porphyrin Anchors for Supramolecular DNA Assemblies

KAUST Repository

Börjesson, Karl

2010-09-28

We have synthesized and studied a supramolecular system comprising a 39-mer DNA with porphyrin-modified thymidine nucleosides anchored to the surface of large unilamellar vesicles (liposomes). Liposome porphyrin binding characteristics, such as orientation, strength, homogeneity, and binding site size, was determined, suggesting that the porphyrin is well suited as a photophysical and redox-active lipid anchor, in comparison to the inert cholesterol anchor commonly used today. Furthermore, the binding characteristics and hybridization capabilities were studied as a function of anchor size and number of anchoring points, properties that are of importance for our future plans to use the addressability of these redox-active nodes in larger DNA-based nanoconstructs. Electron transfer from photoexcited porphyrin to a lipophilic benzoquinone residing in the lipid membrane was characterized by steady-state and time-resolved fluorescence and verified by femtosecond transient absorption. © 2010 American Chemical Society.

Effects of anchoring and arc structure on the control authority of a rail plasma actuator

International Nuclear Information System (INIS)

Choi, Young-Joon; Gray, Miles; Sirohi, Jayant; Raja, Laxminarayan L

2017-01-01

Experiments were conducted on a rail plasma actuator (RailPAc) with different electrode cross sections (rails or rods) to assess methods to improve the actuation authority, defined as the impulse generated for a given electrical input. The arc was characterized with electrical measurements and high-speed images, while impulse measurements quantified the actuation authority. A RailPAc power supply capable of delivering  ∼1 kA of current at  ∼100 V was connected to rod electrodes (free-floating with circular cross-section) and rail electrodes (flush-mounted in a flat plate with rectangular cross-section). High-speed images show that the rail electrodes cause the arc to anchor itself to the anode electrode and transit in discrete jumps, while rod electrodes permit the arc to transit smoothly without anchoring. The impulse measurements reveal that the anchoring reduces the actuation authority by  ∼21% compared to a smooth transit, and the effect of anchoring can be suppressed by reducing the gap between the rails to 2 mm. The study further demonstrates that if a smooth transit is achieved, the control authority can be increased with a larger gap and larger arc current. In conclusion, the actuation authority of a RailPAc can be maximized by carefully choosing a gap width that prevents anchoring. Further study is warranted to increase the RailPAc actuation authority by introducing multiple turns of wires beneath the RailPAc to augment the induced magnetic field. (paper)

Effectiveness of TAD-anchored maxillary protraction in late mixed dentition.

Science.gov (United States)

Feng, Xiaoxia; Li, Jianhua; Li, Yu; Zhao, Zhihe; Zhao, Sen; Wang, Jue

2012-11-01

To evaluate the effectiveness of temporary anchorage device (TAD)-anchored maxillary protraction (MP) in terms of the skeletal and dentoalveolar changes and to compare it with traditional tooth-anchored MP. A computerized literature search for relative randomized controlled trials and prospective controlled trials was performed in PubMed, MEDLINE, Cochrane Central Register of Controlled Trials, Embase, CNKI, and Google Scholar, complemented with manual search. Data extraction and quality assessment were carried out by two reviewers independently. Meta-analysis was followed when possible; otherwise, description was done. Forty articles were found, among which four trials were qualified for meta-analysis. The results showed that there was significant difference between TAD-anchored MP and untreated control in terms of maxillary advancement (weighted mean differences (WMD) 3.08 mm; 95% CI: 1.61 to approximately 4.56; P TAD-anchored MP might have a greater maxillary advancement effect and might reduce skeletal and dental side effects, compared with tooth-anchored MP.

Empirical evidence for resource-rational anchoring and adjustment.

Science.gov (United States)

Lieder, Falk; Griffiths, Thomas L; M Huys, Quentin J; Goodman, Noah D

2018-04-01

People's estimates of numerical quantities are systematically biased towards their initial guess. This anchoring bias is usually interpreted as sign of human irrationality, but it has recently been suggested that the anchoring bias instead results from people's rational use of their finite time and limited cognitive resources. If this were true, then adjustment should decrease with the relative cost of time. To test this hypothesis, we designed a new numerical estimation paradigm that controls people's knowledge and varies the cost of time and error independently while allowing people to invest as much or as little time and effort into refining their estimate as they wish. Two experiments confirmed the prediction that adjustment decreases with time cost but increases with error cost regardless of whether the anchor was self-generated or provided. These results support the hypothesis that people rationally adapt their number of adjustments to achieve a near-optimal speed-accuracy tradeoff. This suggests that the anchoring bias might be a signature of the rational use of finite time and limited cognitive resources rather than a sign of human irrationality.

Thermal anchoring of wires in large scale superconducting coil test experiment

International Nuclear Information System (INIS)

Patel, Dipak; Sharma, A.N.; Prasad, Upendra; Khristi, Yohan; Varmora, Pankaj; Doshi, Kalpesh; Pradhan, S.

2013-01-01

Highlights: • We addressed how thermal anchoring in large scale coil test is different compare to small cryogenic apparatus? • We did precise estimation of thermal anchoring length at 77 K and 4.2 K heat sink in large scale superconducting coil test experiment. • We addressed, the quality of anchoring without covering entire wires using Kapton/Teflon tape. • We obtained excellent results in temperature measurement without using GE Varnish by doubling estimated anchoring length. -- Abstract: Effective and precise thermal anchoring of wires in cryogenic experiment is mandatory to measure temperature in milikelvin accuracy and to avoid unnecessary cooling power due to additional heat conduction from room temperature (RT) to operating temperature (OT) through potential, field, displacement and stress measurement instrumentation wires. Instrumentation wires used in large scale superconducting coil test experiments are different compare to cryogenic apparatus in terms of unique construction and overall diameter/area due to errorless measurement in large time-varying magnetic field compare to small cryogenic apparatus, often shielded wires are used. Hence, along with other variables, anchoring techniques and required thermal anchoring length are entirely different in this experiment compare to cryogenic apparatus. In present paper, estimation of thermal anchoring length of five different types of instrumentation wires used in coils test campaign at Institute for Plasma Research (IPR), India has been discussed and some temperature measurement results of coils test campaign have been presented

Strength of bone tunnel versus suture anchor and push-lock construct in Broström repair.

Science.gov (United States)

Giza, Eric; Nathe, Ryan; Nathe, Tyler; Anderson, Matthew; Campanelli, Valentina

2012-06-01

Operative treatment of mechanical ankle instability is indicated for patients who have had multiple sprains and have continued episodes of instability despite bracing and rehabilitation. Anatomic reconstruction has been shown to have improved outcomes and return to sport as compared with nonanatomic reconstruction. The use of 2 suture anchors and a push-lock anchor is equal to 2 bone tunnels in strength to failure for anatomic Broström repair. Controlled laboratory study. In 7 matched pairs of human cadaver ankles, the calcaneofibular ligament (CFL) and anterior talofibular ligament (ATFL) were incised from their origin on the fibula. A No. 2 Fiberwire suture was placed into the CFL and a separate suture into the ATFL in a running Krackow fashion with a total of 4 locking loops. In 1 ankle of the matched pair, the ligaments were repaired to their anatomic insertion with bone tunnels. In the other, 2 suture anchors were used to reattach the ligaments to their anatomic origins, and a push-lock was used proximally to reinforce these suture anchors. The ligaments were cyclically loaded 20 times and then tested to failure. Torque to failure, degrees to failure, and stiffness were measured. The authors performed a matched pair analysis. An a priori power analysis of 0.8 demonstrated 6 pairs were needed to show a difference of 30% with a 15% standard error at a significance level of .05. There was no difference in the degrees to failure, torque to failure, and stiffness. A post hoc power analysis of torque to failure showed a power of .89 with 7 samples. Power for initial stiffness was .97 with 7 samples. Eleven of 14 specimens failed at either the suture anchor or the bone tunnel. There is no statistical difference in strength or stiffness for a suture anchor and push-lock construct as compared with a bone tunnel construct for an anatomic repair of the lateral ligaments of the ankle. The use of suture anchors in lateral ligament stabilization allows for a smaller

Design and Vibration Sensitivity Analysis of a MEMS Tuning Fork Gyroscope with an Anchored Diamond Coupling Mechanism

Directory of Open Access Journals (Sweden)

Yanwei Guan

2016-04-01

Full Text Available In this paper, a new micromachined tuning fork gyroscope (TFG with an anchored diamond coupling mechanism is proposed while the mode ordering and the vibration sensitivity are also investigated. The sense-mode of the proposed TFG was optimized through use of an anchored diamond coupling spring, which enables the in-phase mode frequency to be 108.3% higher than the anti-phase one. The frequencies of the in- and anti-phase modes in the sense direction are 9799.6 Hz and 4705.3 Hz, respectively. The analytical solutions illustrate that the stiffness difference ratio of the in- and anti-phase modes is inversely proportional to the output induced by the vibration from the sense direction. Additionally, FEM simulations demonstrate that the stiffness difference ratio of the anchored diamond coupling TFG is 16.08 times larger than the direct coupling one while the vibration output is reduced by 94.1%. Consequently, the proposed new anchored diamond coupling TFG can structurally increase the stiffness difference ratio to improve the mode ordering and considerably reduce the vibration sensitivity without sacrificing the scale factor.

Retroperitoneal aortic hemorrhage caused by penetration of an endovascular stent-graft anchoring barb.

Science.gov (United States)

Twine, Christopher P; Winterbottom, Andrew; Shaida, Nadeem; Boyle, Jonathan R

2013-08-01

To report a rare case of acute intraoperative retroperitoneal hemorrhage secondary to aortic penetration by the suprarenal anchoring barb on a stent-graft. A 75-year-old patient on dual antiplatelet therapy for coronary stents and low-molecular-weight heparin for atrial thrombus underwent elective endovascular repair of a 6.7-cm infrarenal abdominal aortic aneurysm. A device with suprarenal fixation and metal anchoring barbs was implanted, and a molding balloon was used that at no time covered the proximal bare metal stents or barbs. In recovery, the patient became tachycardic and hypotensive. After resuscitation, imaging identified an anterior barb penetrating the aortic wall, causing the acute retroperitoneal hemorrhage. A decision to treat conservatively rather than resort to open surgery was difficult but ultimately influenced by the patients' high risk for open surgery. The patient was treated by aggressive reversal of heparin and platelet transfusion, and the bleed settled spontaneously. Major surgery and subsequent morbidity may be avoided by medical management of what would appear to be a surgical problem.

Strand Tension Control in Anchor Span for Suspension Bridge Using Dynamic Balance Theory

Directory of Open Access Journals (Sweden)

Da Wang

Full Text Available Abstract Strand tension control is essential in suspension bridge safety. However, few quantitative studies have examined the bending rigidity and boundary condition behavior of strands in the anchor span of suspension bridges because of their special structure and complex configuration. In this paper, a new calculation method for strand tension is explored by using dynamic balance theory to determine the effect of bending rigidity and boundary conditions. The accuracy and effectiveness of the proposed method are tested and confirmed with verification examples and application on Nanxi Yangtze Suspension Bridge in China. The results indicated that only low-order frequency calculation could be used to calculate the strand tension without considering the effect of bending rigidity to ensure control accuracy. The influence of bending rigidity on the control precision is related to the tension and the length of the strands, which is significantly determined by the specific value between the stress rigidity and the bending rigidity. The uncertain boundary conditions of the anchor span cable, which are fixed between consolidated and hinged, also have a major effect on the control accuracy. To improve the accuracy of strand tension control, the least squares method is proposed during the tension construction control of the anchor span. This approach can significantly improve the accuracy of the tension control of the main cable strand. Some recommendations for future bridge analysis are provided based on the results of this study.

Satisfaction with Dental Appearance and Attitude toward improving Dental Esthetics among Patients attending a Dental Teaching Center.

Science.gov (United States)

Maghaireh, Ghada A; Alzraikat, Hanan; Taha, Nessrin A

2016-01-01

The aim of this study was to evaluate the factors influencing the satisfaction of dental appearance and attitude toward treatments to improve dental esthetics among patients attending a dental teaching center. A questionnaire was used to collect data of four background variables among 450 patients attended a dental teaching center in the city of Irbid in Jordan. The questionnaire enclosed self-reported questions about the appearance of anterior teeth, received esthetic treatment and desired treatment for improving esthetics. Descriptive, multiple logistic regression and Chi-square tests were used for data analysis (p ≤ 0.05). The 450 participants consisted of (66.2%) male and (33.8%) female. Of these, 69.3% were satisfied with their dental appearance and 58.0% with the color of their teeth. Esthetic restorations were the most received treatment (39.8%) and whitening of teeth was the most desired treatment (55.3%). The patients' satisfaction with dental appearance was influenced by teeth color, crowding and receiving whitening (p < 0.05. r = 0.561, r(2) = 0.315). The most desired esthetic treatments influenced by the satisfaction with dental appearance were esthetic restorations and orthodontics (p < 0.05. r = 0.223, r(2) = 0.05). Significantly more female reported having esthetic restorations and orthodontics (p = 0.008, 0.000) and desired to have orthodontic, crowns or veneers and esthetic restorations (p = 0.000, 0.015, 0.028). Satisfaction with dental appearance was affected by teeth color, feeling teeth are crowded, desire for esthetic restorations and orthodontic treatment. A high percentage of patients were not satisfied with the color of their teeth. Recognizing the factors that affect patients' satisfaction with their present dental appearance and attitude toward treatments to improve dental esthetic can guide clinicians to strategies to improve esthetics.

Understanding low uptake of bone anchored hearing ads: A review.

OpenAIRE

Powell, Rachael; Wearden, Alison; Pardesi, Sophie M; Green, Kevin

2017-01-01

Background: Bone anchored hearing aids (Baha) improve hearing for patients for whom conventional behind-the-ear aids are problematic. However, uptake of Baha is low and it is important to understand why this is the case. Method: A narrative review was conducted. Studies examining why people accept or decline Baha and satisfaction in people with Baha were reviewed. Results: Reasons for declining Baha included limited perceived benefits, concerns about surgery, aesthetic concerns and treatment ...

Cyclic biomechanical testing of biocomposite lateral row knotless anchors in a human cadaveric model.

Science.gov (United States)

Barber, F Alan; Bava, Eric D; Spenciner, David B; Piccirillo, Justin

2013-06-01

The purpose of this study was to assess the mechanical performance of biocomposite knotless lateral row anchors based on both anchor design and the direction of pull. Two lateral row greater tuberosity insertion sites (anterior and posterior) were identified in matched pairs of fresh-frozen human cadaveric shoulders DEXA (dual energy X-ray absorptiometry) scanned to verify comparability. The humeri were stripped of all soft tissue and 3 different biocomposite knotless lateral row anchors: HEALIX Knotless BR (DePuy Mitek, Raynham MA), BioComposite PushLock (Arthrex, Naples, FL), and Bio-SwiveLock (Arthrex). Fifty-two anchors were distributed among the insertion locations and tested them with either an anatomic or axial pull. A fixed-gauge loop (15 mm) of 2 high-strength sutures from each anchor was created. After a 10-Nm preload, anchors were cycled from 10 to 45 Nm at 0.5 Hz for 200 cycles and tested to failure at 4.23 mm/second. The load to reach 3 mm and 5 mm displacement, ultimate failure load, displacement at ultimate failure, and failure mode were recorded. Threaded anchors (Bio-SwiveLock, P = .03; HEALIX Knotless, P = .014) showed less displacement with anatomic testing than did the nonthreaded anchor (BioComposite PushLock), and the HEALIX Knotless showed less overall displacement than did the other 2 anchors. The Bio-SwiveLock exhibited greater failure loads than did the other 2 anchors (P < .05). Comparison of axial and anatomic loading showed no maximum load differences for all anchors as a whole (P = .1084). Yet, anatomic pulling produced higher failure loads than did axial pulling for the Bio-SwiveLock but not for the BioComposite PushLock or the HEALIX Knotless. The nonthreaded anchor (BioComposite PushLock) displayed lower failure loads than did both threaded anchors with axial pulling. Threaded biocomposite anchors (HEALIX Knotless BR and Bio-SwiveLock) show less anatomic loading displacement and higher axial failure loads than do the nonthreaded

The anchors of steel wire ropes, testing methods and their results

Directory of Open Access Journals (Sweden)

J. Krešák

2012-10-01

Full Text Available The present paper introduces an application of the acoustic and thermographic method in the defectoscopic testing of immobile steel wire ropes at the most critical point, the anchor. First measurements and their results by these new defectoscopic methods are shown. In defectoscopic tests at the anchor, the widely used magnetic method gives unreliable results, and therefore presents a problem for steel wire defectoscopy. Application of the two new methods in the steel wire defectoscopy at the anchor point will enable increased safety measures at the anchor of steel wire ropes in bridge, roof, tower and aerial cable lift constructions.

Failure Capacity Evaluation for Anchor System of NPP Facilities by using a Shaking Table Test

International Nuclear Information System (INIS)

Kwon, Hyung O; Jung, Min Ki; Park, Jin Wan; Lim, Ji Hoon

2010-02-01

This study investigate the destructive influence of crack locations on the anchor performance to evaluate the seismic performance of NPP equipment anchored on damaged concrete. For this purpose, small-scale specimens were fabricated according to the following three cases: 1) with a non-damaged anchor; 2) with cracks running through the anchor; and 3) with cracks along the expected corn-shape fracture away from the anchor. The result verified with the finite element method is as follows: In the first and second cases that is, with a non-damaged anchor and with cracks running through the anchor destruction occurred at the anchor steel. In the third case that is, with cracks around the anchor, a 30% decline in the seismic performance was identified. This result indicates that evaluation of seismic performance and relevant reinforcement are required when cracks occur away from the anchor along the expected destructive surface

The anchoring bias reflects rational use of cognitive resources.

Science.gov (United States)

Lieder, Falk; Griffiths, Thomas L; M Huys, Quentin J; Goodman, Noah D

2018-02-01

Cognitive biases, such as the anchoring bias, pose a serious challenge to rational accounts of human cognition. We investigate whether rational theories can meet this challenge by taking into account the mind's bounded cognitive resources. We asked what reasoning under uncertainty would look like if people made rational use of their finite time and limited cognitive resources. To answer this question, we applied a mathematical theory of bounded rationality to the problem of numerical estimation. Our analysis led to a rational process model that can be interpreted in terms of anchoring-and-adjustment. This model provided a unifying explanation for ten anchoring phenomena including the differential effect of accuracy motivation on the bias towards provided versus self-generated anchors. Our results illustrate the potential of resource-rational analysis to provide formal theories that can unify a wide range of empirical results and reconcile the impressive capacities of the human mind with its apparently irrational cognitive biases.

Anchored but not internalized: shape dependent endocytosis of nanodiamond

Science.gov (United States)

Zhang, Bokai; Feng, Xi; Yin, Hang; Ge, Zhenpeng; Wang, Yanhuan; Chu, Zhiqin; Raabova, Helena; Vavra, Jan; Cigler, Petr; Liu, Renbao; Wang, Yi; Li, Quan

2017-04-01

Nanoparticle-cell interactions begin with the cellular uptake of the nanoparticles, a process that eventually determines their cellular fate. In the present work, we show that the morphological features of nanodiamonds (NDs) affect both the anchoring and internalization stages of their endocytosis. While a prickly ND (with sharp edges/corners) has no trouble of anchoring onto the plasma membrane, it suffers from difficult internalization afterwards. In comparison, the internalization of a round ND (obtained by selective etching of the prickly ND) is not limited by its lower anchoring amount and presents a much higher endocytosis amount. Molecular dynamics simulation and continuum modelling results suggest that the observed difference in the anchoring of round and prickly NDs likely results from the reduced contact surface area with the cell membrane of the former, while the energy penalty associated with membrane curvature generation, which is lower for a round ND, may explain its higher probability of the subsequent internalization.

Plant glycosylphosphatidylinositol (GPI) anchored proteins at the plasma membrane-cell wall nexus.

Science.gov (United States)

Yeats, Trevor H; Bacic, Antony; Johnson, Kim L

2018-04-18

Approximately 1% of plant proteins are predicted to be post-translationally modified with a glycosylphosphatidylinositol (GPI) anchor that tethers the polypeptide to the outer leaflet of the plasma membrane. While the synthesis and structure of GPI anchors is largely conserved across eukaryotes, the repertoire of functional domains present in the GPI-anchored proteome has diverged substantially. In plants, this includes a large fraction of the GPI-anchored proteome being further modified with plant-specific arabinogalactan (AG) O-glycans. The importance of the GPI-anchored proteome to plant development is underscored by the fact that GPI biosynthetic null mutants exhibit embryo lethality. Mutations in genes encoding specific GPI-anchored proteins (GAPs) further supports their contribution to diverse biological processes occurring at the interface of the plasma membrane and cell wall, including signaling, cell wall metabolism, cell wall polymer cross-linking, and plasmodesmatal transport. Here, we review the literature concerning plant GPI-anchored proteins in the context of their potential to act as molecular hubs that mediate interactions between the plasma membrane and the cell wall and their potential to transduce the signal into the protoplast and thereby activate signal transduction pathways. This article is protected by copyright. All rights reserved.

Numerical Simulation of Electro-Mechanical Impedance Response in Cable-Anchor Connection Interface

International Nuclear Information System (INIS)

Nguyen, Khac Duy; Kim, Jeong Tae

2011-01-01

In this study, a finite element(FE) analysis on electro-mechanical impedance response of cable-anchor connection interface under various anchor force is presented. In order to achieve the objective, the following approaches are implemented. Firstly, an interface washer coupled with piezoelectric(PZT) material is designed for monitoring cable-force loss. The interface washer is a small aluminum plate on which a PZT patch is surface-bonded. Cable-force loss could be monitored by installing the interface washer between the anchor plate and the anchorage of cable-anchor connection and examining the changes of impedance of the interface washer. Secondly, a FE model for cable-anchor connection is established to examine the effect of cable-force on impedance response of interface washer. Also, the effects of geometrical and material properties of the interface washer on impedance responses under various cable-forces are investigated. Finally, validation of the FE analysis is experimentally evaluated by a lab-scale cable-anchor connection

Proteomic analysis of GPI-anchored membrane proteins

DEFF Research Database (Denmark)

Jung, Hye Ryung; Jensen, Ole Nørregaard

2006-01-01

Glycosyl-phosphatidyl-inositol-anchored proteins (GPI-APs) represent a subset of post-translationally modified proteins that are tethered to the outer leaflet of the plasma membrane via a C-terminal GPI anchor. GPI-APs are found in a variety of eukaryote species, from pathogenic microorganisms...... to humans. GPI-APs confer important cellular functions as receptors, enzymes and scaffolding molecules. Specific enzymes and detergent extraction methods combined with separation technologies and mass spectrometry permit proteomic analysis of GPI-APs from plasma membrane preparations to reveal cell...

Anchor stabilization of trapped particle modes in mirror machines

International Nuclear Information System (INIS)

Berk, H.L.; Roslyakov, G.V.

1986-07-01

It is shown that for trapped particle modes in tandem mirrors, the pressure of the passing particles in the anchor region introduces a stabilizing term proportional to the sum of the anchor's field line curvature and total diamagnetic pressure. The theory is applied to the proposed gas dynamic trap experiment

Anchor stabilization of trapped particle modes in mirror machines

International Nuclear Information System (INIS)

Berk, H.L.; Roslyakov, G.V.

1986-04-01

It is shown that for trapped particle modes in tandem mirrors, the pressure of the passing particles in the anchor region introduces a stabilizing term proportional to the sum of the anchor's field line curvature and total diamagnetic pressure. The theory is applied to the proposed gas dynamic trap experiment

Functionalized Nanostructures: Redox-Active Porphyrin Anchors for Supramolecular DNA Assemblies

KAUST Repository

Börjesson, Karl; Wiberg, Joanna; El-Sagheer, Afaf H.; Ljungdahl, Thomas; Må rtensson, Jerker; Brown, Tom; Nordén, Bengt; Albinsson, Bo

2010-01-01

, such as orientation, strength, homogeneity, and binding site size, was determined, suggesting that the porphyrin is well suited as a photophysical and redox-active lipid anchor, in comparison to the inert cholesterol anchor commonly used today. Furthermore

Steel shear strength of anchors with stand-off base plates.

Science.gov (United States)

2013-09-01

Sign and signal structures are often connected to concrete foundations through a stand-off annular base plate with a double-nut anchor bolt connection, which leaves exposed anchor bolt lengths below leveling nuts used in these connections. Cantilever...

Simplified design of flexible expansion anchored plates for nuclear structures

International Nuclear Information System (INIS)

Mehta, N.K.; Hingorani, N.V.; Longlais, T.G.; Sargent and Lundy, Chicago, IL)

1984-01-01

In nuclear power plant construction, expansion anchored plates are used to support pipe, cable tray and HVAC duct hangers, and various structural elements. The expansion anchored plates provide flexibility in the installation of field-routed lines where cast-in-place embedments are not available. General design requirements for expansion anchored plate assemblies are given in ACI 349, Appendix B (1). The manufacturers recommend installation procedures for their products. Recent field testing in response to NRC Bulletin 79-02 (2) indicates that anchors, installed in accordance with manufacturer's recommended procedures, perform satisfactorily under static and dynamic loading conditions. Finite element analysis is a useful tool to correctly analyze the expansion anchored plates subject to axial tension and biaxial moments, but it becomes expensive and time-consuming to apply this tool for a large number of plates. It is, therefore, advantageous to use a simplified method, even though it may be more conservative as compared to the exact method of analysis. This paper presents a design method referred to as the modified rigid plate analysis approach to simplify both the initial design and the review of as-built conditions

The Effect of Anchors and Training on the Reliability of Voice Quality Ratings for Different Types of Speech Stimuli.

Science.gov (United States)

Brinca, Lilia; Batista, Ana Paula; Tavares, Ana Inês; Pinto, Patrícia N; Araújo, Lara

2015-11-01

The main objective of the present study was to investigate if the type of voice stimuli-sustained vowel, oral reading, and connected speech-results in good intrarater and interrater agreement/reliability. A short-term panel study was performed. Voice samples from 30 native European Portuguese speakers were used in the present study. The speech materials used were (1) the sustained vowel /a/, (2) oral reading of the European Portuguese version of "The Story of Arthur the Rat," and (3) connected speech. After an extensive training with textual and auditory anchors, the judges were asked to rate the severity of dysphonic voice stimuli using the phonation dimensions G, R, and B from the GRBAS scale. The voice samples were judged 6 months and 1 year after the training. Intrarater agreement and reliability were generally very good for all the phonation dimensions and voice stimuli. The highest interrater reliability was obtained using the oral reading stimulus, particularly for phonation dimensions grade (G) and breathiness (B). Roughness (R) was the voice quality that was the most difficult to evaluate, leading to interrater unreliability in all voice quality ratings. Extensive training using textual and auditory anchors and the use of anchors during the voice evaluations appear to be good methods for auditory-perceptual evaluation of dysphonic voices. The best results of interrater reliability were obtained when the oral reading stimulus was used. Breathiness appears to be a voice quality that is easier to evaluate than roughness. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Biomechanical advantages of triple-loaded suture anchors compared with double-row rotator cuff repairs.

Science.gov (United States)

Barber, F Alan; Herbert, Morley A; Schroeder, F Alexander; Aziz-Jacobo, Jorge; Mays, Matthew M; Rapley, Jay H

2010-03-01

To evaluate the strength and suture-tendon interface security of various suture anchors triply and doubly loaded with ultrahigh-molecular weight polyethylene-containing sutures and to evaluate the relative effectiveness of placing these anchors in a single-row or double-row arrangement by cyclic loading and then destructive testing. The infraspinatus muscle was reattached to the original humeral footprint by use of 1 of 5 different repair patterns in 40 bovine shoulders. Two single-row repairs and three double-row repairs were tested. High-strength sutures were used for all repairs. Five groups were studied: group 1, 2 triple-loaded screw suture anchors in a single row with simple stitches; group 2, 2 triple-loaded screw anchors in a single row with simple stitches over a fourth suture passed perpendicularly ("rip-stop" stitch); group 3, 2 medial and 2 lateral screw anchors with a single vertical mattress stitch passed from the medial anchors and 2 simple stitches passed from the lateral anchors; group 4, 2 medial double-loaded screw anchors tied in 2 mattress stitches and 2 push-in lateral anchors capturing the medial sutures in a "crisscross" spanning stitch; and group 5, 2 medial double-loaded screw anchors tied in 2 mattress stitches and 2 push-in lateral anchors creating a "suture-bridge" stitch. The specimens were cycled between 10 and 180 N at 1.0 Hz for 3,500 cycles or until failure. Endpoints were cyclic loading displacement (5 and 10 mm), total displacement, and ultimate failure load. A single row of triply loaded anchors was more resistant to stretching to a 5- and 10-mm gap than the double-row repairs with or without the addition of a rip-stop suture (P row repair (P row created by 2 medial double-loaded suture anchors and 2 lateral push-in anchors stretched more than any other group (P row repairs with either crossing sutures or 4 separate anchor points were more likely to fail (5- or 10-mm gap) than a single-row repair loaded with 3 simple sutures

Management of subluxated capsular bag-fixated intraocular lenses using a capsular anchor

NARCIS (Netherlands)

Ton, Yokrat; Naftali, Modi; Lapid Gortzak, Ruth; Assia, Ehud I.

2016-01-01

We describe the use of the capsular anchor (AssiAnchor) to manage a subluxated intraocular lens (IOL) in the capsular bag. The anchor comprises 2 prongs that hold the anterior lens capsule and a central rod that is sutured to the scleral wall, enabling centration of the IOL-capsular bag complex. Six

Suture slippage in knotless suture anchors resulting in subacromial-subdeltoid bursitis.

Science.gov (United States)

Hayeri, Mohammad Reza; Keefe, Daniel T; Chang, Eric Y

2016-05-01

Rotator cuff repair using a suture bridge and knotless suture anchors is a relatively new, but increasingly used technique. The suture bridge technique creates an anatomically similar and more secure rotator cuff repair compared with conventional arthroscopic techniques and the use of knotless anchors eliminates the challenges associated with knot tying during arthroscopic surgery. However, previous in vitro biomechanical tests have shown that the hold of the suture in a knotless suture anchor is far lower than the pullout strength of the anchor from bone. Up until now slippage has been a theoretical concern. We present a prospectively diagnosed case of in vivo suture loosening after rotator cuff repair using a knotless bridge technique resulting in subacromial-subdeltoid bursitis.

Biomechanical comparison of a single-row versus double-row suture anchor technique for rotator cuff repair.

Science.gov (United States)

Kim, David H; Elattrache, Neal S; Tibone, James E; Jun, Bong-Jae; DeLaMora, Sergai N; Kvitne, Ronald S; Lee, Thay Q

2006-03-01

Reestablishment of the native footprint during rotator cuff repair has been suggested as an important criterion for optimizing healing potential and fixation strength. A double-row rotator cuff footprint repair will demonstrate superior biomechanical properties compared with a single-row repair. Controlled laboratory study. In 9 matched pairs of fresh-frozen cadaveric shoulders, the supraspinatus tendon from 1 shoulder was repaired with a double-row suture anchor technique: 2 medial anchors with horizontal mattress sutures and 2 lateral anchors with simple sutures. The tendon from the contralateral shoulder was repaired using a single lateral row of 2 anchors with simple sutures. Each specimen underwent cyclic loading from 10 to 180 N for 200 cycles, followed by tensile testing to failure. Gap formation and strain over the footprint area were measured using a video digitizing system; stiffness and failure load were determined from testing machine data. Gap formation for the double-row repair was significantly smaller (P row repair for the first cycle (1.67 +/- 0.75 mm vs 3.10 +/- 1.67 mm, respectively) and the last cycle (3.58 +/- 2.59 mm vs 7.64 +/- 3.74 mm, respectively). The initial strain over the footprint area for the double-row repair was nearly one third (P row repair. Adding a medial row of anchors increased the stiffness of the repair by 46% and the ultimate failure load by 48% (P row repair improved initial strength and stiffness and decreased gap formation and strain over the footprint when compared with a single-row repair. To achieve maximal initial fixation strength and minimal gap formation for rotator cuff repair, reconstructing the footprint attachment with 2 rows of suture anchors should be considered.

Understanding Rasch Measurement: Partial Credit Model and Pivot Anchoring.

Science.gov (United States)

Bode, Rita K.

2001-01-01

Describes the Rasch measurement partial credit model, what it is, how it differs from other Rasch models, and when and how to use it. Also describes the calibration of instruments with increasingly complex items. Explains pivot anchoring and illustrates its use and describes the effect of pivot anchoring on step calibrations, item hierarchy, and…

Weighing the Benefits of Anchored Math Instruction for Students with Disabilities in General Education Classes.

Science.gov (United States)

Bottge, Brian A.; Heinrichs, Mary; Mehta, Zara Dee; Hung, Ya-Hui

2002-01-01

A study examined the effectiveness of enhanced anchor instruction and traditional problem instruction in improving the problem-solving performance of 42 seventh-graders with and without disabilities in inclusive classrooms. Students without disabilities profited from contextualized instruction, but benefits for the students with disabilities were…

Model test of anchoring effect on zonal disintegration in deep surrounding rock masses.

Science.gov (United States)

Chen, Xu-Guang; Zhang, Qiang-Yong; Wang, Yuan; Liu, De-Jun; Zhang, Ning

2013-01-01

The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

Model Test of Anchoring Effect on Zonal Disintegration in Deep Surrounding Rock Masses

Directory of Open Access Journals (Sweden)

Xu-Guang Chen

2013-01-01

Full Text Available The deep rock masses show a different mechanical behavior compared with the shallow rock masses. They are classified into alternating fractured and intact zones during the excavation, which is known as zonal disintegration. Such phenomenon is a great disaster and will induce the different excavation and anchoring methodology. In this study, a 3D geomechanics model test was conducted to research the anchoring effect of zonal disintegration. The model was constructed with anchoring in a half and nonanchoring in the other half, to compare with each other. The optical extensometer and optical sensor were adopted to measure the displacement and strain changing law in the model test. The displacement laws of the deep surrounding rocks were obtained and found to be nonmonotonic versus the distance to the periphery. Zonal disintegration occurs in the area without anchoring and did not occur in the model under anchoring condition. By contrasting the phenomenon, the anchor effect of restraining zonal disintegration was revealed. And the formation condition of zonal disintegration was decided. In the procedure of tunnel excavation, the anchor strain was found to be alternation in tension and compression. It indicates that anchor will show the nonmonotonic law during suppressing the zonal disintegration.

Calculation of anchor forces on penetration liners for the reactor vessel Schmehausen (Germany)

International Nuclear Information System (INIS)

Roennert, J.K.

1976-01-01

Penetrations through the walls of the single cavity PCPV Prestressed Concrete Pressure Vessel for the 300 MW(e) reactor are lined with steel penetration liners welded to the liner of the cavity. For gas-tightness of the system the penetrations are closed by covers. To secure their integration with the concrete, the liners are anchored to it by means of shear studs and/or angles. Being embedded in concrete, over the full width of the walls, the liners are exposed to lateral and longitudinal concrete deformations causing forces on the anchors. The axial blow-out force due to the pressure of the coolant on the closures must also be transferred through the anchors to the concrete. In the design of anchored penetration liners stress analyses are performed to determine anchor forces under different loading conditions and at several ages of the PCPV. The present paper deals with the mathematical estimation of the anchor forces on the basis of given concrete deformations, temperature of liners, and pressure in the vessel by the method of replacing the penetration liners and their anchors by a spring model with linear stiffness characteristics for both the liner and the anchors. An example of the computations on a digital computer is shown. (author)

A scale distortion theory of anchoring.

Science.gov (United States)

Frederick, Shane W; Mochon, Daniel

2012-02-01

We propose that anchoring is often best interpreted as a scaling effect--that the anchor changes how the response scale is used, not how the focal stimulus is perceived. Of importance, we maintain that this holds true even for so-called objective scales (e.g., pounds, calories, meters, etc.). In support of this theory of scale distortion, we show that prior exposure to a numeric standard changes respondents' use of that specific response scale but does not generalize to conceptually affiliated judgments rendered on similar scales. Our findings highlight the necessity of distinguishing response language effects from representational effects in places where the need for that distinction has often been assumed away.

Retractable Robotic Anchor for Hard Rock and Granular Soils, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — ProtoInnovations, LLC, is developing an innovative retractable robotic anchor that works in hard rock and granular soils permitting anchoring and subsequent...

Software Note: Using BILOG for Fixed-Anchor Item Calibration

Science.gov (United States)

DeMars, Christine E.; Jurich, Daniel P.

2012-01-01

The nonequivalent groups anchor test (NEAT) design is often used to scale item parameters from two different test forms. A subset of items, called the anchor items or common items, are administered as part of both test forms. These items are used to adjust the item calibrations for any differences in the ability distributions of the groups taking…

Not all nutrition claims are perceived equal: anchoring effects and moderating mechanisms in food advertising.

Science.gov (United States)

Paek, Hye-Jin; Yoon, Hye Jin; Hove, Thomas

2011-03-01

Despite the increased use of health claims in food advertising, few studies have investigated how specific nutrition claims have differential effects depending on how they are presented. In this context, the current study tests the anchoring hypothesis. Anchoring refers to a common human tendency to evaluate information differently depending on the presence or absence of a numerical "anchor" or reference point. Two (pilot and main) experimental studies explore anchoring effects on audience response to food advertising both directly and moderated by cognitive, motivational, and message factors. The pilot study finds that food product ads employing nutrition claims with an anchor rather than without an anchor generate two results: First, participants perceive the product to have lower fat/lower calorie contents (anchoring hypothesis); second, they prefer the messages with an anchor over those without an anchor. The main study reports that when anchoring is successfully evoked, it produces favorable attitudes toward the ad, favorable attitudes toward the brand, and purchase intention-but only when moderated by health orientation, claim believability, and nutrition knowledge. Practical implications are provided with respect to regulatory guidelines and effective communication strategies for promoting low-fat and low-calorie products in food advertising.

Career Anchors: Results of an Organisational Study in the UK.

Science.gov (United States)

Yarnall, Jane

1998-01-01

Career anchors of 374 British employees were identified using Schein's questionnaire. Age, gender, and length of service had no significant effect on distribution of anchors. Job level had some relationship. The information could be used to determine appropriate career-development strategies. (SK)

Robotic Ankle for Omnidirectional Rock Anchors

Science.gov (United States)

Parness, Aaron; Frost, Matthew; Thatte, Nitish

2013-01-01

Future robotic exploration of near-Earth asteroids and the vertical and inverted rock walls of lava caves and cliff faces on Mars and other planetary bodies would require a method of gripping their rocky surfaces to allow mobility without gravitational assistance. In order to successfully navigate this terrain and drill for samples, the grippers must be able to produce anchoring forces in excess of 100 N. Additionally, the grippers must be able to support the inertial forces of a moving robot, as well gravitational forces for demonstrations on Earth. One possible solution would be to use microspine arrays to anchor to rock surfaces and provide the necessary load-bearing abilities for robotic exploration of asteroids. Microspine arrays comprise dozens of small steel hooks supported on individual suspensions. When these arrays are dragged along a rock surface, the steel hooks engage with asperities and holes on the surface. The suspensions allow for individual hooks to engage with asperities while the remaining hooks continue to drag along the surface. This ensures that the maximum possible number of hooks engage with the surface, thereby increasing the load-bearing abilities of the gripper. Using the microspine array grippers described above as the end-effectors of a robot would allow it to traverse terrain previously unreachable by traditional wheeled robots. Furthermore, microspine-gripping robots that can perch on cliffs or rocky walls could enable a new class of persistent surveillance devices for military applications. In order to interface these microspine grippers with a legged robot, an ankle is needed that can robotically actuate the gripper, as well as allow it to conform to the large-scale irregularities in the rock. The anchor serves three main purposes: deploy and release the anchor, conform to roughness or misalignment with the surface, and cancel out any moments about the anchor that could cause unintentional detachment. The ankle design contains a

Assessment of behavior, design and testing of anchors for fastening to concrete

Energy Technology Data Exchange (ETDEWEB)

Yoon, Young Soo; Choi, Han Tae; Jung, Woo Young; Park, Sung Kyun [Korea Univ., Seoul (Korea, Republic of)

1998-11-15

This report presents the evaluation of behavior and the prediction of tensile capacity of anchors that fail concrete, as the design basis for anchorage. Tests of cast-in place headed anchors, domestically manufactured and installed in uncracked, unreinforced concrete were performed to investigate the behavior of single anchors and multiple anchors with the consideration of various embedment lengths and edge distances. The failure mode and the load-deformation response of these anchors are discussed and the concrete failure data then compared with capacities by the two exiting methods : the 45 degree cone method of ACI 349, appendix B and the Concrete Capacity Design (CCD) method. Discrepancies between the test results and these two prediction methods are assessed and also the basic differences in philosophy and the factors contributing to the philosophical differences in these two methods are addressed.

Effects of anchoring and adjustment in the evaluation of product pricing.

Science.gov (United States)

Elaad, Eitan; Sayag, Neta; Ezer, Aliya

2010-08-01

Anchoring and adjustment comprise a heuristic that creates expectations. Two types of anchors were applied on participants' evaluation of products: the price reference of the product (maximum, minimum, or no price reference) and the context in which the products were evaluated (the prestige of the shopping center). Results showed that both factors anchored evaluations of products' value. Context effects were explained by the different expectations of visitors in prestigious (looking for quality) and less prestigious (seeking a bargain) centers.

Characterization of the C-terminal ER membrane anchor of PTP1B

International Nuclear Information System (INIS)

Anderie, Ines; Schulz, Irene; Schmid, Andreas

2007-01-01

The tyrosine phosphatase PTP1B is an important regulator of cell function. In living cells PTP1B activity is restricted to the vicinity of the endoplasmic reticulum (ER) by post-translational C-terminal attachment of PTP1B to the ER membrane network. In our study we investigated the membrane anchor of PTP1B by use of EGFP fusion proteins. We demonstrate that the membrane anchor of PTP1B cannot be narrowed down to a unique amino acid sequence with a defined start and stop point but rather is moveable within several amino acids. Removal of up to seven amino acids from the C-terminus, as well as exchange of single amino acids in the putative transmembrane sequence did not influence subcellular localization of PTP1B. With the method of bimolecular fluorescence complementation we could demonstrate dimerization of PTP1B in vivo. Homodimerization was, in contrast to other tail-anchored proteins, not dependent on the membrane anchor. Our data demonstrate that the C-terminal membrane anchor of PTP1B is formed by a combination of a single stretch transmembrane domain (TMD) followed by a tail. TMD and tail length are variable and there are no sequence-specific features. Our data for PTP1B are consistent with a concept that explains the ER membrane anchor of tail-anchored proteins as a physicochemical structure

Reinforcing mechanism of anchors in slopes: a numerical comparison of results of LEM and FEM

Science.gov (United States)

Cai, Fei; Ugai, Keizo

2003-06-01

This paper reports the limitation of the conventional Bishop's simplified method to calculate the safety factor of slopes stabilized with anchors, and proposes a new approach to considering the reinforcing effect of anchors on the safety factor. The reinforcing effect of anchors can be explained using an additional shearing resistance on the slip surface. A three-dimensional shear strength reduction finite element method (SSRFEM), where soil-anchor interactions were simulated by three-dimensional zero-thickness elasto-plastic interface elements, was used to calculate the safety factor of slopes stabilized with anchors to verify the reinforcing mechanism of anchors. The results of SSRFEM were compared with those of the conventional and proposed approaches for Bishop's simplified method for various orientations, positions, and spacings of anchors, and shear strengths of soil-grouted body interfaces. For the safety factor, the proposed approach compared better with SSRFEM than the conventional approach. The additional shearing resistance can explain the influence of the orientation, position, and spacing of anchors, and the shear strength of soil-grouted body interfaces on the safety factor of slopes stabilized with anchors.

Conceptualization and Exploration of Composite Career Anchors: An Analysis of Information Systems Personnel.

Science.gov (United States)

Ramakrishna, Hindupur V.; Potosky, Denise

2003-01-01

Information systems professionals (n=163) completed measures of career anchors and outcomes (career/job satisfaction, job performance, perceived advancement prospects); 46% had multiple dominant anchors and these individuals did not have significantly different career outcomes than those with single dominant anchors. (Contains 26 references.) (SK)

An anchoring system for fish habitat structures: field technique, evaluation, and application.

Science.gov (United States)

Barbara L. Fontaine; Thomas D. Merritt

1988-01-01

Steel cable can be used to bind rocks and logs together to construct fish habitat structures in streams. Cables must be securely anchored if structures are to withstand floods. This paper describes a way to anchor cables into bedrock or ballast boulders. Anchor tensile strength ranged from 7,500 to 36,500 pounds and was related to type of resin and embedment depth....

Knotless single-row rotator cuff repair: a comparative biomechanical study of 2 knotless suture anchors.

Science.gov (United States)

Efird, Chad; Traub, Shaun; Baldini, Todd; Rioux-Forker, Dana; Spalazzi, Jeffrey P; Davisson, Twana; Hawkins, Monica; McCarty, Eric

2013-08-01

The purpose of this study was to compare the gap formation during cyclic loading, maximum repair strength, and failure mode of single-row full-thickness supraspinatus repairs performed using 2 knotless suture anchors with differing internal suture-retention mechanisms in a human cadaver model. Nine matched pairs of cadaver shoulders were used. Full-thickness tears were induced by detaching the supraspinatus tendon from the greater tuberosity. Single-row repairs were performed with either type I (Opus Magnum PI; ArthroCare, Austin, Texas) or type II (ReelX STT; Stryker, Mahwah, New Jersey) knotless suture anchors. The repaired tendon was cycled from 10 to 90 N for 500 cycles, followed by load to failure. Gap formation was measured at 5, 100, 200, 300, 400, and 500 cycles with a video digitizing system. Anchor type or location (anterior or posterior) had no effect on gap formation during cyclic loading regardless of position (anterior, P=.385; posterior, P=.389). Maximum load to failure was significantly greater (P=.018) for repairs performed with type II anchors (288±62 N) compared with type I anchors (179±39 N). Primary failure modes were anchor pullout and tendon tearing for type II anchors and suture slippage through the anchor for type I anchors. The internal ratcheting suture-retention mechanism of type II anchors may have helped this anchor outperform the suture-cinching mechanism of type I anchors by supporting significantly higher loads before failure and minimizing suture slippage, potentially leading to stronger repairs clinically. Copyright 2013, SLACK Incorporated.

Display of GPI-anchored anti-EGFR nanobodies on extracellular vesicles promotes tumour cell targeting

Directory of Open Access Journals (Sweden)

Sander A. A. Kooijmans

2016-03-01

Full Text Available Background: Extracellular vesicles (EVs are attractive candidate drug delivery systems due to their ability to functionally transport biological cargo to recipient cells. However, the apparent lack of target cell specificity of exogenously administered EVs limits their therapeutic applicability. In this study, we propose a novel method to equip EVs with targeting properties, in order to improve their interaction with tumour cells. Methods: EV producing cells were transfected with vectors encoding for anti-epidermal growth factor receptor (EGFR nanobodies, which served as targeting ligands for tumour cells, fused to glycosylphosphatidylinositol (GPI anchor signal peptides derived from decay-accelerating factor (DAF. EVs were isolated using ultrafiltration/size-exclusion liquid chromatography and characterized using western blotting, Nanoparticle Tracking Analysis, and electron microscopy. EV–tumour cell interactions were analyzed under static conditions using flow cytometry and under flow conditions using a live-cell fluorescence microscopy-coupled perfusion system. Results: V analysis showed that GPI-linked nanobodies were successfully displayed on EV surfaces and were highly enriched in EVs compared with parent cells. Display of GPI-linked nanobodies on EVs did not alter general EV characteristics (i.e. morphology, size distribution and protein marker expression, but greatly improved EV binding to tumour cells dependent on EGFR density under static conditions. Moreover, nanobody-displaying EVs showed a significantly improved cell association to EGFR-expressing tumour cells under flow conditions. Conclusions: We show that nanobodies can be anchored on the surface of EVs via GPI, which alters their cell targeting behaviour. Furthermore, this study highlights GPI-anchoring as a new tool in the EV toolbox, which may be applied for EV display of a variety of proteins, such as antibodies, reporter proteins and signaling molecules.

Extracellular glycosylphosphatidylinositol-anchored mannoproteins and proteases of Cryptococcus neoformans.

Science.gov (United States)

Eigenheer, Richard A; Jin Lee, Young; Blumwald, Eduardo; Phinney, Brett S; Gelli, Angie

2007-06-01

Extracellular proteins of Cryptococcus neoformans are involved in the pathogenesis of cryptococcosis, and some are immunoreactive antigens that may potentially serve as candidates for vaccine development. To further study the extracellular proteome of the human fungal pathogen Cry. neoformans, we conducted a proteomic analysis of secreted and cell wall-bound proteins with an acapsular strain of Cry. neoformans. Proteins were identified from both intact cells and cell walls. In both cases, extracellular proteins were removed with trypsin or beta-glucanase, and then all proteins/peptides were purified by solid-phase extraction, spin dialysis, and HPLC, and identified by liquid chromatography-mass spectrometry. This study identified 29 extracellular proteins with a predicted N-terminal signal sequence and also a predicted glycosylphosphatidylinositol anchor motif in more than half. Among the novel proteins identified were five glycosylphosphatidylinositol-anchored proteins with extensive Ser/Thr-rich regions but no apparent functional domains, a glycosylphosphatidylinositol-anchored aspartic protease, and a metalloprotease with structural similarity to an elastinolytic metalloprotease of Aspergillus fumigatus. This study suggests that Cry. neoformans has the machinery required to target glycosylphosphatidylinositol-anchored proteins to the cell wall, and it confirms the extracellular proteolytic ability of Cry. neoformans.

Small-angle light scattering symmetry breaking in polymer-dispersed liquid crystal films with inhomogeneous electrically controlled interface anchoring

Energy Technology Data Exchange (ETDEWEB)

Loiko, V. A., E-mail: loiko@ifanbel.bas-net.by; Konkolovich, A. V. [National Academy of Sciences of Belarus, Stepanov Institute of Physics (Belarus); Zyryanov, V. Ya. [Russian Academy of Sciences, Kirensky Institute of Physics, Federal Research Center “Krasnoyarsk Scientific Center,” Siberian Branch (Russian Federation); Miskevich, A. A. [National Academy of Sciences of Belarus, Stepanov Institute of Physics (Belarus)

2017-03-15

We have described the method of analyzing and reporting on the results of calculation of the small-angle structure of radiation scattered by a polymer-dispersed liquid crystal film with electrically controlled interfacial anchoring. The method is based on the interference approximation of the wave scattering theory and the hard disk model. Scattering from an individual liquid crystal droplet has been described using the anomalous diffraction approximation extended to the case of droplets with uniform and nonuniform interface anchoring at the droplet–polymer boundary. The director field structure in an individual droplet is determined from the solution of the problem of minimizing the volume density of the free energy. The electrooptical effect of symmetry breaking in the angular distribution of scattered radiation has been analyzed. This effect means that the intensities of radiation scattered within angles +θ{sub s} and–θ{sub s} relative to the direction of illumination in the scattering plane can be different. The effect is of the interference origin and is associated with asymmetry of the phase shift of the wavefront of an incident wave from individual parts of the droplet, which appears due to asymmetry of the director field structure in the droplet, caused by nonuniform anchoring of liquid crystal molecules with the polymer on its surface. This effect is analyzed in the case of normal illumination of the film depending on the interfacial anchoring at the liquid crystal–polymer interface, the orientation of the optical axes of droplets, their concentration, sizes, anisometry, and polydispersity.

Development of a Behaviorally Anchored Rating Scale for Leadership

Science.gov (United States)

2018-01-01

Research Product 2018-06 Development of a Behaviorally Anchored Rating Scale for Leadership Tatiana H. Toumbeva Krista L...anchored Rating Scale for Leadership 5a. CONTRACT NUMBER W5J9CQ-11-D-0004 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62278 6...observer- based behavioral measure to help instructors more reliably and accurately evaluate the development of leadership attributes and competencies

Enhancement of Orthodontic Anchor Screw Stability Under Immediate Loading by Ultraviolet Photofunctionalization Technology.

Science.gov (United States)

Takahashi, Maiko; Motoyoshi, Mitsuru; Inaba, Mizuki; Hagiwara, Yoshiyuki; Shimizu, Noriyoshi

Ultraviolet (UV)-mediated photofunctionalization technology is intended to enhance the osseointegration capability of titanium implants. There are concerns about orthodontic anchor screws loosening under immediate loading protocols in adolescent orthodontic treatment. The purpose of this in vivo study was to evaluate the effects of photofunctionalization on the intrabony stability of orthodontic titanium anchor screws and bone-anchor screw contact under immediate loading in growing rats. Custom-made titanium anchor screws (1.4 mm in diameter and 4.0 mm in length) with or without photofunctionalization pretreatment were placed on the proximal epiphysis of the tibial bone in 6-week-old male Sprague-Dawley rats and were loaded immediately after placement. After 2 weeks of loading, the stability of the anchor screws was evaluated using a Periotest device, and the bone-anchor screw contact ratio (BSC) was assessed by a histomorphometric analysis using field-emission scanning electron microscopy. In the unloaded group, Periotest values (PTVs) were ~25 for UV-untreated screws and 13 for UVtreated screws (P < .01), while in the immediate-loading group, PTVs were 28 for UV-untreated screws and 16 for UV-treated screws (P < .05). Significantly less screw mobility was observed in both UV-treated groups regardless of the loading protocol. The BSC was increased ~1.8 fold for UV-treated screws, compared with UV-untreated screws, regardless of the loading protocol. Photofunctionalization enhanced the intrabony stability of orthodontic anchor screws under immediate loading in growing rats by increasing bone-anchor screw contact.

Management of subluxated capsular bag-fixated intraocular lenses using a capsular anchor.

Science.gov (United States)

Ton, Yokrat; Naftali, Modi; Gortzak, Ruth Lapid; Assia, Ehud I

2016-05-01

We describe the use of the capsular anchor (AssiAnchor) to manage a subluxated intraocular lens (IOL) in the capsular bag. The anchor comprises 2 prongs that hold the anterior lens capsule and a central rod that is sutured to the scleral wall, enabling centration of the IOL-capsular bag complex. Six pseudophakic patients presenting with subluxated posterior chamber IOLs in the capsular bag were operated on using the device. The anchor was used successfully in all cases, although in 2 cases only 1 prong was placed under the capsulorhexis edge. In 1 eye, 2 anchors were used 1 month apart following repeated traumatic zonular injury. The capsular bag holding the IOL remained centered and stable throughout the follow-up period. The anchoring device, which was originally designed to preserve the lens capsule and stabilize subluxated crystalline lenses, can also be used to treat subluxation of a capsular bag-fixated IOL. Dr. Assia is the inventor of the AssiAnchor, has a licensed patent of the anchor, and is consultant to Hanita Lenses. Dr. Lapid-Gortzak is a consultant to and speaker for Alcon Surgical, Inc., Hanita Lenses, Orca Surgical, and Sanoculis Ltd.; a speaker for Santen; and a consultant to Icon. Drs. Ton and Naftali have no financial or proprietary interest in any material or method mentioned. Copyright © 2016 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Time trade-off and attitudes toward euthanasia: implications of using 'death' as an anchor in health state valuation.

Science.gov (United States)

Augestad, Liv A; Rand-Hendriksen, Kim; Stavem, Knut; Kristiansen, Ivar Sønbø

2013-05-01

Health state values are by convention anchored to 'perfect health' and 'death.' Attitudes toward death may consequently influence the valuations. We used attitudes toward euthanasia (ATE) as a sub-construct for attitudes toward death. We compared the influence on values elicited with time trade-off (TTO), lead-time TTO (LT-TTO) and visual analogue scale (VAS).Since the 'death' anchor is most explicit in TTO, we hypothesized that TTO values would be most influenced by ATE. Respondents valued eight EQ-5D health states with VAS, then TTO (n = 328) or LT-TTO (n = 484). We measured ATE on a scale from -2 (fully disagree) to 2 (fully agree) and used multiple linear regressions to predict VAS, TTO, and LT-TTO values by ATE, sex, age, and education. A one-point increase on the ATE scale predicted a mean TTO value change of -.113 and LT-TTO change of -.072. Demographic variables, but not ATE, predicted VAS values. TTO appears to measure ATE in addition to preferences for health states. Different ways of incorporating death in the valuation may impact substantially on the resulting values. 'Death' is a metaphysically unknown concept, and implications of attitudes toward death should be investigated further to evaluate the appropriateness of using 'death' as an anchor.

HKUST-1 Membranes Anchored on Porous Substrate by Hetero MIL-110 Nanorod Array Seeds.

Science.gov (United States)

Mao, Yiyin; Cao, Wei; Li, Junwei; Sun, Luwei; Peng, Xinsheng

2013-09-02

Great anchors and seeds: Hetero-seeding growth processes and anchored nanorod arrays were successfully utilized in the synthesis of HKUST-1 membranes. These arrays were firmly anchored on porous substrates by using a MIL-110 nanorod array as both the anchor and seed. The resulting HKUST-1 membranes demonstrated good separation factors for binary gases exceeding the Knudson selectivity. Copyright © 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

Stability calculation method of slope reinforced by prestressed anchor in process of excavation.

Science.gov (United States)

Li, Zhong; Wei, Jia; Yang, Jun

2014-01-01

This paper takes the effect of supporting structure and anchor on the slope stability of the excavation process into consideration; the stability calculation model is presented for the slope reinforced by prestressed anchor and grillage beam, and the dynamic search model of the critical slip surface also is put forward. The calculation model of the optimal stability solution of each anchor tension of the whole process is also given out, through which the real-time analysis and checking of slope stability in the process of excavation can be realized. The calculation examples indicate that the slope stability is changed with the dynamic change of the design parameters of anchor and grillage beam. So it is relatively more accurate and reasonable by using dynamic search model to determine the critical slip surface of the slope reinforced by prestressed anchor and grillage beam. Through the relationships of each anchor layout and the slope height of various stages of excavation, and the optimal stability solution of prestressed bolt tension design value in various excavation stages can be obtained. The arrangement of its prestressed anchor force reflects that the layout of the lower part of bolt and the calculation of slope reinforcement is in line with the actual. These indicate that the method is reasonable and practical.

Spontaneous insertion of GPI anchors into cholesterol-rich membrane domains

Directory of Open Access Journals (Sweden)

Jing Li

2018-05-01

Full Text Available GPI-Anchored proteins (GPI-APs can be exogenously transferred onto bilayer membranes both in vivo and in vitro, while the mechanism by which this transfer process occurs is unknown. In this work, we used atomistic molecular dynamics simulations and free energy calculations to characterize the essential influence of cholesterol on insertion of the GPI anchors into plasma membranes. We demonstrate, both dynamically and energetically, that in the presence of cholesterol, the tails of GPI anchors are able to penetrate inside the core of the lipid membrane spontaneously with a three-step mechanism, while in the absence of cholesterol no spontaneous insertion was observed. We ascribe the failure of insertion to the strong thermal fluctuation of lipid molecules in cholesterol-free bilayer, which generates a repulsive force in entropic origin. In the presence of cholesterol, however, the fluctuation of lipids is strongly reduced, thus decreasing the barrier for the anchor insertion. Based on this observation, we propose a hypothesis that addition of cholesterol creates vertical creases in membranes for the insertion of acyl chains. Moreover, we find that the GPI anchor could also spontaneously inserted into the boundary between cholesterol-rich and cholesterol-depleted domains. Our results shed light on the mechanism of cholesterol-mediated interaction between membrane proteins with acyl chain and plasma membranes in living cells.

Spontaneous insertion of GPI anchors into cholesterol-rich membrane domains

Science.gov (United States)

Li, Jing; Liu, Xiuhua; Tian, Falin; Yue, Tongtao; Zhang, Xianren; Cao, Dapeng

2018-05-01

GPI-Anchored proteins (GPI-APs) can be exogenously transferred onto bilayer membranes both in vivo and in vitro, while the mechanism by which this transfer process occurs is unknown. In this work, we used atomistic molecular dynamics simulations and free energy calculations to characterize the essential influence of cholesterol on insertion of the GPI anchors into plasma membranes. We demonstrate, both dynamically and energetically, that in the presence of cholesterol, the tails of GPI anchors are able to penetrate inside the core of the lipid membrane spontaneously with a three-step mechanism, while in the absence of cholesterol no spontaneous insertion was observed. We ascribe the failure of insertion to the strong thermal fluctuation of lipid molecules in cholesterol-free bilayer, which generates a repulsive force in entropic origin. In the presence of cholesterol, however, the fluctuation of lipids is strongly reduced, thus decreasing the barrier for the anchor insertion. Based on this observation, we propose a hypothesis that addition of cholesterol creates vertical creases in membranes for the insertion of acyl chains. Moreover, we find that the GPI anchor could also spontaneously inserted into the boundary between cholesterol-rich and cholesterol-depleted domains. Our results shed light on the mechanism of cholesterol-mediated interaction between membrane proteins with acyl chain and plasma membranes in living cells.

AnchorDock for Blind Flexible Docking of Peptides to Proteins.

Science.gov (United States)

Slutzki, Michal; Ben-Shimon, Avraham; Niv, Masha Y

2017-01-01

Due to increasing interest in peptides as signaling modulators and drug candidates, several methods for peptide docking to their target proteins are under active development. The "blind" docking problem, where the peptide-binding site on the protein surface is unknown, presents one of the current challenges in the field. AnchorDock protocol was developed by Ben-Shimon and Niv to address this challenge.This protocol narrows the docking search to the most relevant parts of the conformational space. This is achieved by pre-folding the free peptide and by computationally detecting anchoring spots on the surface of the unbound protein. Multiple flexible simulated annealing molecular dynamics (SAMD) simulations are subsequently carried out, starting from pre-folded peptide conformations, constrained to the various precomputed anchoring spots.Here, AnchorDock is demonstrated using two known protein-peptide complexes. A PDZ-peptide complex provides a relatively easy case due to the relatively small size of the protein, and a typical peptide conformation and binding region; a more challenging example is a complex between USP7 N-term and a p53-derived peptide, where the protein is larger, and the peptide conformation and a binding site are generally assumed to be unknown. AnchorDock returned native-like solutions ranked first and third for the PDZ and USP7 complexes, respectively. We describe the procedure step by step and discuss possible modifications where applicable.

The Analysis Stability of Anchor Retaining Wall

International Nuclear Information System (INIS)

Benamara, F. Z.; Belabed, L

2011-01-01

The construction of anchored retaining walls reach every day in the field of Civil Engineering especially in public works. Their dimensioning and stability are the axes of research for geotechnical. The rule is to reduce the active forces of the slide and increase the effective normal stress on the rupture surface. So that, we anchored tied-back (constituted by steel cables) in the stable ground located under the failure surface and we apply at the top a traction force. This effort can be distributed over the ground surface by means of small plates or massive reinforced concrete. The study of the stability of anchored retaining wall was also performed by using software GEO4. Many cases can be solved using analytical solutions available in the group GEO4 program, but for our standard model solution studied analytically proved unsatisfactory so we used a numerical analysis based on the method of finite element in this program. The results obtained by numerical study were interpreted to identify the precision numerical predictions. Moreover these methods were useful and economics in the realization of reinforced slopes by tied-buck. (author)

A study on plate anchor detailing systems of shear re-bar

International Nuclear Information System (INIS)

Tsurumaki, S.; Ujiie, K.; Nishikawa, T.; Kitayama, K.

1995-01-01

For shell walls and base slabs in reactor buildings, besides a large amount of main bars, numerous shear re-bars have been employed to resist to out-of-plane force. As a result , detailing work involving shear re-bar is extremely involved. For example, the employed re-bar anchor method differs from the ordinary methods in which, a end of shear re-bar with 135-degrees hook or with anchor plate type and another re-bar end with 90-degrees hook are used. However the structural characteristics in members using shear re-bar of the bolt-mounted anchor plate have not yet been examined. A test was performed to confirm the effects of anchor methods for shear re-bars on shearing behavior of members. This paper describes the test plan, method and results. (author). 12 figs., 7 tabs

Grapnel stone anchors from Saurashtra: Remnants of Indo-Arab trade on the Indian coast

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.

Stone anchors have been used as a primary source of information on ancient navigation by marine archaeologists since long. These anchors used by ancient mariners are often noticed underwater at various places across the world. Stone anchors are also...

Proteomic analysis of glycosylphosphatidylinositol-anchored membrane proteins

DEFF Research Database (Denmark)

Elortza, Felix; Nühse, Thomas S; Foster, Leonard J

2003-01-01

Glycosylphosphatidylinositol-anchored proteins (GPI-APs) are a functionally and structurally diverse family of post-translationally modified membrane proteins found mostly in the outer leaflet of the plasma membrane in a variety of eukaryotic cells. Although the general role of GPI-APs remains...... unclear, they have attracted attention because they act as enzymes and receptors in cell adhesion, differentiation, and host-pathogen interactions. GPI-APs may represent potential diagnostic and therapeutic targets in humans and are interesting in plant biotechnology because of their key role in root...... and 44 GPI-APs in an Arabidopsis thaliana membrane preparation, representing the largest experimental dataset of GPI-anchored proteins to date....

Electrochromic mirror using viologen-anchored nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Kim, Han Na [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of); Cho, Seong M.; Ah, Chil Seong; Song, Juhee; Ryu, Hojun; Kim, Yong Hae [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); Kim, Tae-Youb, E-mail: youby@etri.re.kr [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of)

2016-10-15

Highlights: • Three types of ECM device were fabricated using viologen-anchored ECDs. • The devices were investigated according to their optical structures. • The anti-reflection material affects the reflectance and the coloration efficiency. • The device design of ECMs is a crucial factor for clear reflected images. - Abstract: Electrochromic mirrors (ECMs) that are used in automobile mirrors need to have high reflectance, a high contrast ratio, and a clear image. In particular, it is critical that distortions of clear images are minimized for safety. Therefore, an ECM is fabricated using viologen-anchored nanoparticles and a magnesium fluoride (MgF{sub 2}) layer with an anti-reflection function. The ECM has approximately 30.42% in the reflectance dynamic range and 125 cm{sup 2}/C high coloration efficiency.

Comprehensive evaluation of Streptococcus sanguinis cell wall-anchored proteins in early infective endocarditis.

Science.gov (United States)

Turner, Lauren Senty; Kanamoto, Taisei; Unoki, Takeshi; Munro, Cindy L; Wu, Hui; Kitten, Todd

2009-11-01

Streptococcus sanguinis is a member of the viridans group of streptococci and a leading cause of the life-threatening endovascular disease infective endocarditis. Initial contact with the cardiac infection site is likely mediated by S. sanguinis surface proteins. In an attempt to identify the proteins required for this crucial step in pathogenesis, we searched for surface-exposed, cell wall-anchored proteins encoded by S. sanguinis and then used a targeted signature-tagged mutagenesis (STM) approach to evaluate their contributions to virulence. Thirty-three predicted cell wall-anchored proteins were identified-a number much larger than those found in related species. The requirement of each cell wall-anchored protein for infective endocarditis was assessed in the rabbit model. It was found that no single cell wall-anchored protein was essential for the development of early infective endocarditis. STM screening was also employed for the evaluation of three predicted sortase transpeptidase enzymes, which mediate the cell surface presentation of cell wall-anchored proteins. The sortase A mutant exhibited a modest (approximately 2-fold) reduction in competitiveness, while the other two sortase mutants were indistinguishable from the parental strain. The combined results suggest that while cell wall-anchored proteins may play a role in S. sanguinis infective endocarditis, strategies designed to interfere with individual cell wall-anchored proteins or sortases would not be effective for disease prevention.

Inflation targeting and the anchoring of inflation expectations in the CEE countries

Directory of Open Access Journals (Sweden)

Nedeljković Milan

2017-01-01

Full Text Available This paper studies the time evolution in the degree and level of anchoring of inflation expectations in four Central and Eastern European inflation targeting countries. The results suggest that the degree of anchoring of inflation expectations increased gradually in all countries over the last decade, while the level of implied inflation targets moved towards the official target. The extent of anchoring increased more strongly in the first years following the IT adoption and more gradually over the later period. We also find that smooth changes of the official target had a positive impact on anchoring. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 47028: Advancing Serbia’s Competitiveness in the Process of EU Accession

Reduction of lateral loads in abutments using ground anchors

OpenAIRE

Laefer, Debra F.; Truong-Hong, Linh; Le, Khanh Ba

2013-01-01

In bridge design, economically addressing large, lateral earth pressures on bridge abutments is a major challenge. Traditional approaches employ enlargement of the abutment components to resist these pressures. This approach results in higher construction costs. As an alternative, a formal approach using ground anchors to resist lateral soil pressure on bridge abutments is proposed herein. The ground anchors are designed to minimise lateral forces at the pile cap base. Design examples for hig...

Biomechanical Analysis of Suture Anchor vs Tenodesis Screw for FHL Transfer.

Science.gov (United States)

Drakos, Mark C; Gott, Michael; Karnovsky, Sydney C; Murphy, Conor I; DeSandis, Bridget A; Chinitz, Noah; Grande, Daniel; Chahine, Nadeen

2017-07-01

Chronic Achilles injury is often treated with flexor hallucis longus (FHL) tendon transfer to the calcaneus using 1 or 2 incisions. A single incision avoids the risks of extended dissections yet yields smaller grafts, which may limit fixation options. We investigated the required length of FHL autograft and biomechanical profiles for suture anchor and biotenodesis screw fixation. Single-incision FHL transfer with suture anchor or biotenodesis screw fixation to the calcaneus was performed on 20 fresh cadaveric specimens. Specimens were cyclically loaded until maximal load to failure. Length of FHL tendon harvest, ultimate load, stiffness, and mode of failure were recorded. Tendon harvest length needed for suture anchor fixation was 16.8 ± 2.1 mm vs 29.6 ± 2.4 mm for biotenodesis screw ( P = .002). Ultimate load to failure was not significantly different between groups. A significant inverse correlation existed between failure load and donor age when all specimens were pooled (ρ = -0.49, P Anchor failure occurred mostly by suture breakage (n = 8). Adequate FHL tendon length could be harvested through a single posterior incision for fixation to the calcaneus with either fixation option, but suture anchor required significantly less graft length. Stiffness, fixation strength, and load to failure were comparable between groups. An inverse correlation existed between failure load and donor age. Younger specimens with screw fixation demonstrated significantly greater failure loads. Adequate harvest length for FHL transfer could be achieved with a single posterior incision. There was no difference in strength of fixation between suture anchor and biotenodesis screw.

The Effect of Suture Anchor Insertion Angle on Calcaneus Pullout Strength: Challenging the Deadman's Angle.

Science.gov (United States)

Weiss, William M; Saucedo, Ramon P; Robinson, John D; Lo, Chung-Chieh Jason; Morris, Randal P; Panchbhavi, Vinod K

2017-10-01

Refractory cases of Achilles tendinopathy amenable to surgery may include reattachment of the tendon using suture anchors. However, there is paucity of information describing the optimal insertion angle to maximize the tendon footprint and anchor stability in the calcaneus. The purpose of this investigation is to compare the fixation strength of suture anchors inserted at 90° and 45° (the Deadman's angle) relative to the primary compressive trabeculae of the calcaneus. A total of 12 matched pairs of adult cadaveric calcanei were excised and potted to approximate their alignment in vivo. Each pair was implanted with 5.5-mm bioabsorbable suture anchors placed either perpendicular (90°) or oblique (45°) to the primary compressive trabeculae. A tensile load was applied until failure of anchor fixation. Differences in failure load and stiffness between anchor fixation angles were determined by paired t-tests. No significant differences were detected between perpendicular and oblique suture anchor insertion relative to primary compressive trabeculae in terms of load to failure or stiffness. This investigation suggests that the fixation strength of suture anchors inserted perpendicular to the primary compression trabeculae and at the Deadman's angle are possibly comparable. Biomechanical comparison study.

Stone anchors from Sindhudurg Fort on the west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Gaur, A.S.

, of which there are triangular and three grapnet-type, used to construct the jetty along with the locally available sand stone. The two remaining grapnet-type anchors are erected on the jetty for mooring purposes. It is found that none of the anchors were...

Mean-field density functional theory of a nanoconfined classical, three-dimensional Heisenberg fluid. I. The role of molecular anchoring

Science.gov (United States)

Cattes, Stefanie M.; Gubbins, Keith E.; Schoen, Martin

2016-05-01

In this work, we employ classical density functional theory (DFT) to investigate for the first time equilibrium properties of a Heisenberg fluid confined to nanoscopic slit pores of variable width. Within DFT pair correlations are treated at modified mean-field level. We consider three types of walls: hard ones, where the fluid-wall potential becomes infinite upon molecular contact but vanishes otherwise, and hard walls with superimposed short-range attraction with and without explicit orientation dependence. To model the distance dependence of the attractions, we employ a Yukawa potential. The orientation dependence is realized through anchoring of molecules at the substrates, i.e., an energetic discrimination of specific molecular orientations. If the walls are hard or attractive without specific anchoring, the results are "quasi-bulk"-like in that they can be linked to a confinement-induced reduction of the bulk mean field. In these cases, the precise nature of the walls is completely irrelevant at coexistence. Only for specific anchoring nontrivial features arise, because then the fluid-wall interaction potential affects the orientation distribution function in a nontrivial way and thus appears explicitly in the Euler-Lagrange equations to be solved for minima of the grand potential of coexisting phases.

Stability Analysis of Anchored Soil Slope Based on Finite Element Limit Equilibrium Method

Directory of Open Access Journals (Sweden)

Rui Zhang

2016-01-01

Full Text Available Under the condition of the plane strain, finite element limit equilibrium method is used to study some key problems of stability analysis for anchored slope. The definition of safe factor in slices method is generalized into FEM. The “true” stress field in the whole structure can be obtained by elastic-plastic finite element analysis. Then, the optimal search for the most dangerous sliding surface with Hooke-Jeeves optimized searching method is introduced. Three cases of stability analysis of natural slope, anchored slope with seepage, and excavation anchored slope are conducted. The differences in safety factor quantity, shape and location of slip surface, anchoring effect among slices method, finite element strength reduction method (SRM, and finite element limit equilibrium method are comparatively analyzed. The results show that the safety factor given by the FEM is greater and the unfavorable slip surface is deeper than that by the slice method. The finite element limit equilibrium method has high calculation accuracy, and to some extent the slice method underestimates the effect of anchor, and the effect of anchor is overrated in the SRM.

Composite materials formed with anchored nanostructures

Science.gov (United States)

Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei

2015-03-10

A method of forming nano-structure composite materials that have a binder material and a nanostructure fiber material is described. A precursor material may be formed using a mixture of at least one metal powder and anchored nanostructure materials. The metal powder mixture may be (a) Ni powder and (b) NiAl powder. The anchored nanostructure materials may comprise (i) NiAl powder as a support material and (ii) carbon nanotubes attached to nanoparticles adjacent to a surface of the support material. The process of forming nano-structure composite materials typically involves sintering the mixture under vacuum in a die. When Ni and NiAl are used in the metal powder mixture Ni.sub.3Al may form as the binder material after sintering. The mixture is sintered until it consolidates to form the nano-structure composite material.

Chemical biology of Glycosylphosphatidylinositol (GPI) anchors

Indian Academy of Sciences (India)

Admin

CSIR-IIIM. Chemical biology of. Glycosylphosphatidylinositol (GPI) anchors. Ram Vishwakarma. CSIR-Indian Institute of Integrative Medicine, Jammu. N ti l I tit t f I l. N. D lhi. National Institute of Immunology, New Delhi. Piramal Life Sciences Ltd, Mumbai ...

Model for ion confinement in a hot-electron tandem mirror anchor

International Nuclear Information System (INIS)

Baldwin, D.E.

1980-01-01

Anisotropic, hot electrons trapped in local minimum-B wells have been proposed as MHD-stabilizing anchors to an otherwise axisymmetric tandem configuration. This work describes a model for plasma confinement between the anchors and the remainder of the system and calcuates the power loss implied by maintenance of this plasma

Bioabsorbable Suture Anchor Migration to the Acromioclavicular Joint: How Far Can These Implants Go?

Directory of Open Access Journals (Sweden)

Giovanna Medina

2014-01-01

Full Text Available Few complications regarding the use of bioabsorbable suture anchors in the shoulder have been reported. What motivated this case report was the unusual location of the anchor, found in the acromioclavicular joint which, to our knowledge, has never been reported so far. A 53-year old male with previous rotator cuff (RC repair using bioabsorbable suture anchors presented with pain and weakness after 2 years of surgery. A suspicion of retear of the RC led to request of a magnetic resonance image, in which the implant was found located in the acromioclavicular joint. The complications reported with the use of metallic implants around the shoulder led to the development of bioabsorbable anchors. Advantages are their absorption over time, minimizing the risk of migration or interference with revision surgery, less artifacts with magnetic resonance imaging, and tendon-to-bone repair strength similar to metallic anchors. Since the use of bioabsorbable suture anchors is increasing, it is important to know the possible complications associated with these devices.

Evolutionary morphology in shape and size of haptoral anchors in 14 Ligophorus spp. (Monogenea: Dactylogyridae).

Science.gov (United States)

Rodríguez-González, Abril; Sarabeev, Volodimir; Balbuena, Juan Antonio

2017-01-01

The search for phylogenetic signal in morphological traits using geometric morphometrics represents a powerful approach to estimate the relative weights of convergence and shared evolutionary history in shaping organismal form. We assessed phylogenetic signal in the form of ventral and dorsal haptoral anchors of 14 species of Ligophorus occurring on grey mullets (Osteichthyes: Mugilidae) from the Mediterranean, the Black Sea and the Sea of Azov. The phylogenetic relationships among these species were mapped onto the morphospaces of shape and size of dorsal and ventral anchors and two different tests were applied to establish whether the spatial positions in the morphospace were dictated by chance. Overall significant phylogenetic signal was found in the data. Allometric effects on anchor shape were moderate or non-significant in the case of evolutionary allometry. Relatively phylogenetically distant species occurring on the same host differed markedly in anchor morphology indicating little influence of host species on anchor form. Our results suggest that common descent and shared evolutionary history play a major role in determining the shape and, to a lesser degree in the size of haptoral anchors in Ligophorus spp. The present approach allowed tracing paths of morphological evolution in anchor shape. Species with narrow anchors and long shafts were associated predominately with Liza saliens. This morphology was considered to be ancestral relative to anchors of species occurring on Liza haematocheila and M. cephalus possessing shorter shafts and longer roots. Evidence for phylogenetic signal was more compelling for the ventral anchors, than for the dorsal ones, which could reflect different functional roles in attachment to the gills. Although phylogeny and homoplasy may act differently in other monogeneans, the present study delivers a common framework to address effectively the relationships among morphology, phylogeny and other traits, such as host specificity

Evolutionary morphology in shape and size of haptoral anchors in 14 Ligophorus spp. (Monogenea: Dactylogyridae.

Directory of Open Access Journals (Sweden)

Abril Rodríguez-González

Full Text Available The search for phylogenetic signal in morphological traits using geometric morphometrics represents a powerful approach to estimate the relative weights of convergence and shared evolutionary history in shaping organismal form. We assessed phylogenetic signal in the form of ventral and dorsal haptoral anchors of 14 species of Ligophorus occurring on grey mullets (Osteichthyes: Mugilidae from the Mediterranean, the Black Sea and the Sea of Azov. The phylogenetic relationships among these species were mapped onto the morphospaces of shape and size of dorsal and ventral anchors and two different tests were applied to establish whether the spatial positions in the morphospace were dictated by chance. Overall significant phylogenetic signal was found in the data. Allometric effects on anchor shape were moderate or non-significant in the case of evolutionary allometry. Relatively phylogenetically distant species occurring on the same host differed markedly in anchor morphology indicating little influence of host species on anchor form. Our results suggest that common descent and shared evolutionary history play a major role in determining the shape and, to a lesser degree in the size of haptoral anchors in Ligophorus spp. The present approach allowed tracing paths of morphological evolution in anchor shape. Species with narrow anchors and long shafts were associated predominately with Liza saliens. This morphology was considered to be ancestral relative to anchors of species occurring on Liza haematocheila and M. cephalus possessing shorter shafts and longer roots. Evidence for phylogenetic signal was more compelling for the ventral anchors, than for the dorsal ones, which could reflect different functional roles in attachment to the gills. Although phylogeny and homoplasy may act differently in other monogeneans, the present study delivers a common framework to address effectively the relationships among morphology, phylogeny and other traits, such

Experimental Study On Lateral Load Capacity of Bamboo RC Beam Column Joints Strengthened By Bamboo Mechanical Anchors

Directory of Open Access Journals (Sweden)

Sri Umniati B.

2017-01-01

Full Text Available In this paper, the prospective of bamboos which available abundantly especially in Indonesia as rebars and mechanical anchors are studied. And also the endurance of the bamboos mechanical anchors to withstand cyclic loading were observed. Nine classes of bamboos bar were evaluated: consist of 3 different anchors (0, 4 and 8 anchors and 3 different compressive strength (19.19 MPa, 29.61 MPa and 37.96 MPa means 3 × 3 parameters. The results show that the lateral load capacity increased significantly with the present of bamboo anchors specimens: 26.04 % for 4 anchors specimens (C2 and 25 % for the 8 anchors specimens (C3 compared to zero anchor specimens (C1. On the other hand, the compressive strength of concrete have no significant effects to the lateral load capacity. Overall it can be concluded that, bamboo can be used as mechanical anchorage to strengthen beam column joint.

Data for identification of GPI-anchored peptides and ω-sites in cancer cell lines

Directory of Open Access Journals (Sweden)

Yusuke Masuishi

2016-06-01

Full Text Available We present data obtained using a focused proteomics approach to identify the glycosylphosphatidylinositol (GPI-anchored peptides in 19 human cancer cell lines. GPI-anchored proteins (GPI-APs, which localize to the outer leaflet of the membrane microdomains commonly referred to as lipid rafts play important roles in diverse biological processes. Due to the complex structure of the GPI-anchor moiety, it has been difficult to identify GPI-anchored peptide sequences on the proteomic scale by database searches using tools such as MASCOT. Here we provide data from 73 ω-sites derived from 49 GPI-APs in 19 human cancer cell lines. This article contains data related to the research article entitled “Identification of glycosylphosphatidylinositol-anchored proteins and ω-sites using TiO2-based affinity purification followed by hydrogen fluoride treatment” (Masuishi et al., 2016 [1].

Comprehensive Evaluation of Streptococcus sanguinis Cell Wall-Anchored Proteins in Early Infective Endocarditis▿ †

Science.gov (United States)

Turner, Lauren Senty; Kanamoto, Taisei; Unoki, Takeshi; Munro, Cindy L.; Wu, Hui; Kitten, Todd

2009-01-01

Streptococcus sanguinis is a member of the viridans group of streptococci and a leading cause of the life-threatening endovascular disease infective endocarditis. Initial contact with the cardiac infection site is likely mediated by S. sanguinis surface proteins. In an attempt to identify the proteins required for this crucial step in pathogenesis, we searched for surface-exposed, cell wall-anchored proteins encoded by S. sanguinis and then used a targeted signature-tagged mutagenesis (STM) approach to evaluate their contributions to virulence. Thirty-three predicted cell wall-anchored proteins were identified—a number much larger than those found in related species. The requirement of each cell wall-anchored protein for infective endocarditis was assessed in the rabbit model. It was found that no single cell wall-anchored protein was essential for the development of early infective endocarditis. STM screening was also employed for the evaluation of three predicted sortase transpeptidase enzymes, which mediate the cell surface presentation of cell wall-anchored proteins. The sortase A mutant exhibited a modest (∼2-fold) reduction in competitiveness, while the other two sortase mutants were indistinguishable from the parental strain. The combined results suggest that while cell wall-anchored proteins may play a role in S. sanguinis infective endocarditis, strategies designed to interfere with individual cell wall-anchored proteins or sortases would not be effective for disease prevention. PMID:19703977

Factors influencing patient satisfaction with dental appearance and treatments they desire to improve aesthetics

Directory of Open Access Journals (Sweden)

Hassan Nurhidayati

2011-02-01

Full Text Available Abstract Background We assessed factors influencing patients' satisfaction with their dental appearance and the treatments they desired to improve dental aesthetics. Methods A cross-sectional study was performed out among 235 adult patients who visited the Hospital Universiti Sains Malaysia dental clinic. A structured, interviewer-guided questionnaire was used to identify patient satisfaction with their general dental appearance, cosmetic elements and desired treatments. Results The 235 patients consisted of 70 males (29.8% and 165 females (70.2%, of mean age 31.5 years (SD 13.0. Of these patients, 124 (52.8% were not satisfied with their general dental appearance. In addition, 132 patients (56.2% were not happy with the color of their teeth, 76 (32.3%, regarded their teeth were poorly aligned, 62 (26.4%, as crowded and 56 (23.4% protruded. Dissatisfaction with tooth color was significantly higher in female than in male patients (odds ratio [OR] of 1.99 (95% confidence interval [CI] 1.13-3.50. Tooth whitening was the treatment most desired by patients (48.1%. Results of multiple logistic regression analysis showed that patient dissatisfaction with general dental appearance was significantly associated with female gender (OR = 2.18; 95% CI: 1.18-4.03, unhappiness with tooth color (OR = 3.05; 95% CI: 1.74-5.34 and the opinion that their teeth protruded (OR = 2.91, 95% CI: 1.44-5.91. Conclusions Most patients in this study were not satisfied with their dental appearance with a greater percentage of females expressing dissatisfaction than males. An age was not associated with satisfaction. Unhappiness with tooth color and feelings of having protruding teeth also had a significant negative influence on patient satisfaction with general dental appearance.

Career anchors and career resilience: Supplementary constructs?

Directory of Open Access Journals (Sweden)

L. J. Van Vuuren

2000-06-01

Full Text Available Previously the authors reported on a study in which an attempt was made at defining and measuring the construct career resilience (Fourie & Van Vuuren, 1998. The present article continues this investigation by reporting on the relationship between career resilience and career anchors, as defined in Scheins (1975; 1978; 1990; 1992 career anchor model. The aim of the study was to determine whether career anchor patterning could potentially inhibit or facilitate individuals' levels of career resilience. The "Career Resilience Questionnaire" (CRQ (Fourie & Van Vuuren, 1998 together with Scheins (1990 "Career Orientations Inventory" (COI were administered to 352 skilled employees. The findings regarding the statistical relationship between the two constructs are discussed. Opsomming Loopbaanankers en loopbaangehardheid: supplementere konstrukte? In n vorige publikasie van Fourie en Van Vuuren (1998 is die bevindinge aangaande die afbakening en meting van die konstruk, loopbaangehardheid, gerapporteer. In die huidige artikel word die ondersoek voortgesit met 'n beskrywing van die verwantskap tussen loopbaangehardheid en loopbaanankers, soos gedefinieer in die loopbaanankermodel van Schein (1975; 1978; 1990; 1992. Die doel met die studie was om te bepaal of die mate van loopbaanankerontplooiing individuele vlakke van loopbaangehardheid potensieel fasiliteer ofinhibeer. Die "Career Resilience Questionnaire" (CRQ (Fourie & Van Vuuren, 1998 is tesame met die "Career Orientation Inventory" (COI (Schein, 1990 op 352 geskoolde werknemers geadministreer. Die bevindinge betreffende die statistiese verwantskap tussen die twee konstrukte word bespreek.

Ultraweak azimuthal anchoring of a nematic liquid crystal on a planar orienting photopolymer

International Nuclear Information System (INIS)

Nespoulous, Mathieu; Blanc, Christophe; Nobili, Maurizio

2007-01-01

The search of weak anchoring is an important issue for a whole class of liquid crystal displays. In this paper we present an orienting layer showing unreached weak planar azimuthal anchoring for 4-n-pentyl-4 ' -cyanobiphenyl nematic liquid crystal (5CB). Azimuthal extrapolation lengths as large as 80 μm are easily obtained. Our layers are made with the commercial photocurable polymer Norland optical adhesive 60. The anisotropy of the film is induced by the adsorption of oriented liquid crystal molecules under a 2 T magnetic field applied parallel to the surfaces. We use the width of surface π-walls and a high-field electro-optical method to measure, respectively, the azimuthal and the zenithal anchorings. The azimuthal anchoring is extremely sensitive to the ultraviolet (UV) dose and it also depends on the magnetic field application duration. On the opposite, the zenithal anchoring is only slightly sensitive to the preparation parameters. All these results are discussed in terms of the adsorption/desorption mechanisms of the liquid crystal molecules on the polymer layer and of the flexibility of the polymer network

Factors related to furniture anchoring: a method for reducing harm during earthquakes.

Science.gov (United States)

Haraoka, Tomoko; Hayasaka, Shinya; Murata, Chiyoe; Yamaoka, Taiji; Ojima, Toshiyuki

2013-02-01

Fatalities and injuries during an earthquake can be reduced by taking preemptive measures before-hand, and furniture anchoring is an important safety measure for all residents. This study sought to clarify the factors associated with furniture anchoring within the home. A self-administered mail survey was completed from July to August 2010 by 3500 men and women between the ages of 20 and 69 years who were chosen at random from an official government resident registry of 2 cities in Japan. Of the 1729 valid responses, 37.1% reported furniture anchoring. An association with furniture anchoring was observed for having viewed earthquake intensity maps or damage predictions (odds ratio [OR] 1.92, 95% C1 1.54-2.39), expressing concern about a future earthquake (OR 2.07, 95% C1 1.36-3.15), feelings of urgency (OR 1.90, 95% CI 1.47-2.45), accuracy of the government disaster preparedness information (OR 1.68, 95% CI 1.17-2.42), knowledge of the meaning of emergency earthquake warnings (OR 1.67, 95% CI 1.12-2.48), and participation in voluntary disaster preparedness activities (OR 1.40, 95% C1 1.12-1.75). Furniture anchoring was found to be associated with risk awareness, risk perception, disaster preparedness information provided by government to residents, knowledge of earthquakes, participation in voluntary disaster preparedness activities, nonwooden structures, and marital status. An increase in furniture anchoring is important and can be achieved through education and training in daily life.

Career Anchors: Distribution and Impact on Job Satisfaction, the Israeli Case

Science.gov (United States)

Danziger, Nira; Valency, Rony

2006-01-01

Purpose: The purpose of this paper is to examine the career anchor concept developed by Edgar Schein. Design/methodology/approach: The paper focuses on the distribution of the eight career anchors, on a large heterogeneous sample and the differences in the distribution by gender and type of employment; and the impact of the congruence on job…

Contact area and pressure in suture bridge rotator cuff repair using knotless lateral anchors.

Science.gov (United States)

Tompkins, Marc; Monchik, Keith O; Plante, Matthew J; Fleming, Braden C; Fadale, Paul D

2011-10-01

To evaluate whether the use of knotless lateral anchors in a suture bridge construct produces better contact area and pressure parameters than a suture bridge construct with standard lateral anchors that require knots or a double-row repair. The hypothesis was that knotless lateral anchors would produce better contact area and pressure parameters than the other two constructs. A total of fifteen matched pairs of cadaveric shoulders were divided into three groups. In Group 1, a suture bridge using knotless anchors for the lateral row was performed on five shoulders. A suture bridge using standard lateral row anchors that require knots was performed on the contralateral shoulders. In Group 2, suture bridge with knotless lateral row anchors was compared with double-row repair. In Group 3, suture bridge using standard lateral row anchors was compared with double-row repair. The contact conditions of the rotator cuff footprint were measured using pressure-sensitive film. There were no statistically significant differences between any of the techniques regarding contact area F(2, 15.7) = 3.09, P = 0.07 or mean contact pressure F(2, 15.1) = 2.35, P = 0.12. A post hoc power analysis suggests differences between techniques are likely less than 91-113 mm(2) for area and 0.071-0.089 N for pressure. The use of knotless anchors in the lateral row of a suture bridge repair did not increase the footprint contact area or contact pressure when compared to a suture bridge repair requiring knots laterally or to a double-row repair.

Microfocused Ultrasound with Visualization and Calcium Hydroxylapatite for Improving Skin Laxity and Cellulite Appearance

Science.gov (United States)

Pereira, Gregório

2017-01-01

Background: Age-associated skin laxity contributes to worsening of cellulite appearance. This study evaluated the effects of microfocused ultrasound with visualization (MFU-V; Ultherapy) in combination with diluted calcium hydroxylapatite (CaHA; Radiesse) on cellulite appearance and on neocollagenesis. Methods: Twenty women (18–55 years old) with skin laxity and moderate-to-severe cellulite on the buttocks and thighs were retrospectively enrolled. MFU-V was applied using 4 and 7 MHz transducers (25 lines/transducer/site) and immediately followed by subdermal CaHA injection (1 ml/buttock or thigh). Photographs at baseline and 90 days were assessed by 2 independent, blinded evaluators using a 5-item cellulite severity scale. One subject scheduled for thighplasty received treatment with 6 different CaHA dilutions (0.3 ml/5 cm2) followed by MFU-V. Tissue specimens from each dilution site were examined under polarized light microscopy to assess neocollagenesis. Results: Both evaluators reported statistically significant improvements compared with baseline for each item on the cellulite severity scale (P treatment. At 90 days, histologic analysis showed peak neocollagenesis in samples treated with the 1:1 dilution, whether with CaHA alone or in combination with MFU-V. The highest conversion of collagen type III into collagen type I at month 3 occurred in samples injected with 1:1 and 1:0.6 CaHA dilutions without subsequent MFU-V treatment. Both procedures were well tolerated, and subject satisfaction was high. Conclusions: Combination treatment with MFU-V and diluted CaHA is effective for improving skin laxity and the appearance of cellulite on the buttocks and upper thighs. PMID:28831339

A reusable suture anchor for arthroscopy psychomotor skills training.

Science.gov (United States)

Tillett, Edward D; Rogers, Rainie; Nyland, John

2003-03-01

For residents to adequately develop the early arthroscopy psychomotor skills required to better learn how to manage the improvisational situations they will encounter during actual patient cases, they need to experience sufficient practice repetitions within a contextually relevant environment. Unfortunately, the cost of suture anchors can be a practice repetition-limiting factor in learning arthroscopic knot-tying techniques. We describe a technique for creating inexpensive reusable suture anchors and provide an example of their application to repair the anterior glenoid labrum during an arthroscopy psychomotor skills laboratory training session.

Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

Science.gov (United States)

Hamidah, I.; Wati, R.; Hamdani, R. A.

2018-05-01

The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

JOB SATISFACTION AND CAREER CHOICES: A STUDY USING SCHEIN´S CAREER ANCHOR MODEL

OpenAIRE

Codaro, Rosana Silvina; Tomei, Patricia Amelia; Serra, Bernardo Paraiso de Campos

2017-01-01

This study explores the relationship between job satisfaction and alignment between the individual´s current occupation and his/her talents, needs and values, namely as career anchors. A quantitative survey using Schein e Van Maanen´s Career Anchor model (2013) and Siqueira´s Job Satisfaction survey (2008) was performed for a non-probabilistic sample students at the Business School of a private University in Rio de Janeiro. The most frequent career anchor found for both genders was Lifestyle,...

Development of a New Nondestructive Inspection Strategy for Corroded Multistrand Anchor Cables

Science.gov (United States)

2016-07-01

parking structures, rock and soil anchors, houses, and many other structures. Figure 1 (left) and (middle) show a typical cable and multistrand anchor...primary tool to identify the ideal propagating modes, the inspection itself is typically carried out in the time domain. The selected tone- burst

Investigation into the behaviour of concrete anchored diaphragm walls under earthquake condition

International Nuclear Information System (INIS)

Saba, H. R.; Rahaii, A. R.

2003-01-01

Diaphragm walls are frequently used in civil Engineering projects. Considering the variety and important volume of consumed materials (concrete, anchors and soil), one of the important factors for design and construction of these walls, are their behaviour under different executive, and loading conditions. In this paper, various models of concrete diaphragms with different number of anchors and soil parameters under static and dynamic loading have been investigated using finite element method with nonlinear models. Results including the internal forces in diaphragm walls, variation of forces in the anchors, shape of the sliding surface and variation of pressure in soil are obtained and compared. An experimental tool with suitable measurement systems for determining the pressure and internal forces was designed and realised. Also with similitude and dimensional analyses, diaphragms with different number of anchors were built and set on the shaking table test and experimented under different accelograms. Finally results of nonlinear dynamic analysis were compared with experimental results

The detrimental consequences for seagrass of ineffective marine park management related to boat anchoring.

Science.gov (United States)

La Manna, G; Donno, Y; Sarà, G; Ceccherelli, G

2015-01-15

Posidonia oceanica (L.) Delile meadows are recognized as priority habitat for conservation by the EU Habitats Directive. The La Maddalena Archipelago National Park (Mediterranean Sea) P. oceanica meadow, the dominant coastal habitat of the area, is mostly threatened by boat anchoring. 12 years after the establishment of mooring fields and anchoring restrictions, a study was conducted to measure their effectiveness on the conservation of seagrass and the mitigation of anchoring damage. We found that: (i) the condition of P. oceanica was disturbed, both in the mooring fields and in control locations; (ii) mooring fields and anchoring restrictions did not show to be an efficient system for the protection of seagrass, in fact anchor scars increased after the tourist season; (iii) the mooring systems had an impact on the surrounding area of the meadow, probably due to their misuse. On the basis of these results, management recommendations for marine parks are proposed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effects of carboxyl and ester anchoring groups on solar conversion efficiencies of TiO2 dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Sepehrifard, A.; Stublla, A.; Haftchenary, S.; Chen, S.; Potvin, P.; Morin, S. [York Univ., Toronto, ON (Canada). Dept. of Chemistry

2008-07-01

This paper reported on a study in which 2 new Ruthenium (Ru(2)) dyes bearing different anchoring groups were applied to sensitize TiO2 for dye-sensitized solar cells (DSSCs). The solar conversion efficiencies were measured. Results for 2 of the dyes which carried ester and carboxyl anchoring groups were presented. The extent and nature of the surface binding was studied using electrochemical, UV-visible, fluorescence and FTIR measurements. Solar cell performance was discussed in terms of surface concentration of chemisorbed dyes, electronic properties of the photoanodes and electrochemical properties of adsorbed dyes. The study showed that carboxylic acid groups offer better dye adsorption than ester groups. However, sensitization with warm solutions improved the adsorption of the esterified dye, most likely through transesterification. It was concluded that this may be a useful means of improving solar conversion efficiencies of ester-bearing dyes. 6 refs., 1 tab., 2 figs.

The Holding Power of Anchors

Indian Academy of Sciences (India)

as the chain begins to drag along the ground; and it also serves, by lying flat on the ground, to keep the palm set at the correct angle as it buries itself. In stockless anchors there are two digging blades set on opposite sides of the shank, and hinged to it by a horizontal hinge which allows them to set themselves at the correct.

Optimal suture anchor direction in arthroscopic lateral ankle ligament repair.

Science.gov (United States)

Yoshimura, Ichiro; Hagio, Tomonobu; Noda, Masahiro; Kanazawa, Kazuki; Minokawa, So; Yamamoto, Takuaki

2017-05-26

In this study, the distance between the insertion point of the suture anchors and posterior surface of the fibula during arthroscopic lateral ankle ligament repair was investigated on computed tomography (CT) images. The hypothesis of this study was that there is an optimal insertional direction of the suture anchor to avoid anchor-related complications. One hundred eleven ankles of 98 patients who had undergone three-dimensional CT scans for foot or ankle disorders without deformity of the fibula were assessed (59 males, 52 females; median age 25.5 years; age range 12-78 years). The shortest distance from the insertion point of the suture anchor to the deepest point of the fossa/top of the convex aspect of the fibula was measured on the axial plane, tilting from the longitudinal axis of the fibula at 90°, 75°, 60°, and 45°. The distance from the insertion point of the suture anchor to the posterior surface of the fibula was also measured in a direction parallel to the sagittal plane of the lateral surface of the talus on the axial plane, tilting from the longitudinal axis of the fibula at 90°, 75°, 60°, and 45°. The posterior fossa was observed in all cases on the 90° and 75° images. The distance from the insertion point to the posterior surface of the fibula in the parallel direction was 15.0 ± 3.4 mm at 90°, 17.5 ± 3.2 mm at 75°, 21.7 ± 3.3 mm at 60°, and 25.7 ± 3.6 mm at 45°. The posterior points in the parallel direction were located on the posterior fossa in 36.0% of cases at 90°, in 12.6% at 75°, and in 0.0% at 60° and 45°. The suture anchor should be directed from anterior to posterior at an angle of <45° to the longitudinal axis of the fibula, parallel to the lateral surface of the talus, to avoid passing through the fibula. Cohort study, Level III.

Anchoring effect on first passage process in Taiwan financial market

Science.gov (United States)

Liu, Hsing; Liao, Chi-Yo; Ko, Jing-Yuan; Lih, Jiann-Shing

2017-07-01

Empirical analysis of the price fluctuations of financial markets has received extensive attention because a substantial amount of financial market data has been collected and because of advances in data-mining techniques. Price fluctuation trends can help investors to make informed trading decisions, but such decisions may also be affected by a psychological factors-the anchoring effect. This study explores the intraday price time series of Taiwan futures, and applies diffusion model and quantitative methods to analyze the relationship between the anchoring effect and price fluctuations during first passage process. Our results indicate that power-law scaling and anomalous diffusion for stock price fluctuations are related to the anchoring effect. Moreover, microscopic price fluctuations before switching point in first passage process correspond with long-term price fluctuations of Taiwan's stock market. We find that microscopic trends could provide useful information for understanding macroscopic trends in stock markets.

Career Anchors of United States Air Force Information Systems Workers: A Turnover Predictor

National Research Council Canada - National Science Library

Wynne, Lee

2002-01-01

...) and the work of Schein (1987) to measure the career anchors, job satisfaction, and turnover intention of AF IS workers to determine if those whose job type and career anchor match report higher satisfaction and lower turnover...

Glycosylphosphatidylinositol-anchored proteins are required for cell wall synthesis and morphogenesis in Arabidopsis.

Science.gov (United States)

Gillmor, C Stewart; Lukowitz, Wolfgang; Brininstool, Ginger; Sedbrook, John C; Hamann, Thorsten; Poindexter, Patricia; Somerville, Chris

2005-04-01

Mutations at five loci named PEANUT1-5 (PNT) were identified in a genetic screen for radially swollen embryo mutants. pnt1 cell walls showed decreased crystalline cellulose, increased pectins, and irregular and ectopic deposition of pectins, xyloglucans, and callose. Furthermore, pnt1 pollen is less viable than the wild type, and pnt1 embryos were delayed in morphogenesis and showed defects in shoot and root meristems. The PNT1 gene encodes the Arabidopsis thaliana homolog of mammalian PIG-M, an endoplasmic reticulum-localized mannosyltransferase that is required for synthesis of the glycosylphosphatidylinositol (GPI) anchor. All five pnt mutants showed strongly reduced accumulation of GPI-anchored proteins, suggesting that they all have defects in GPI anchor synthesis. Although the mutants are seedling lethal, pnt1 cells are able to proliferate for a limited time as undifferentiated callus and do not show the massive deposition of ectopic cell wall material seen in pnt1 embryos. The different phenotype of pnt1 cells in embryos and callus suggest a differential requirement for GPI-anchored proteins in cell wall synthesis in these two tissues and points to the importance of GPI anchoring in coordinated multicellular growth.

Anchored LH2 complexes in 2D polarization imaging.

Science.gov (United States)

Tubasum, Sumera; Sakai, Shunsuke; Dewa, Takehisa; Sundström, Villy; Scheblykin, Ivan G; Nango, Mamoru; Pullerits, Tõnu

2013-09-26

Protein is a soft material with inherently large structural disorder. Consequently, the bulk spectroscopies of photosynthetic pigment protein complexes provide averaged information where many details are lost. Here we report spectroscopy of single light-harvesting complexes where fluorescence excitation and detection polarizations are both independently rotated. Two samples of peripheral antenna (LH2) complexes from Rhodopseudomonas acidophila were studied. In one, the complexes were embedded in polyvinyl alcohol (PVA) film; in the other, they were anchored on the glass surface and covered by the PVA film. LH2 contains two rings of pigment molecules-B800 and B850. The B800 excitation polarization properties of the two samples were found to be very similar, indicating that orientation statistics of LH2s are the same in these two very different preparations. At the same time, we found a significant difference in B850 emission polarization statistics. We conclude that the B850 band of the anchored sample is substantially more disordered. We argue that both B800 excitation and B850 emission polarization properties can be explained by the tilt of the anchored LH2s due to the spin-casting of the PVA film on top of the complexes and related shear forces. Due to the tilt, the orientation statistics of two samples become similar. Anchoring is expected to orient the LH2s so that B850 is closer to the substrate. Consequently, the tilt-related strain leads to larger deformation and disorder in B850 than in B800.

ARTHROSCOPIC REPAIR OF BANKART’S LESION USING SUTURE ANCHORS IN RECURRENT ANTERIOR SHOULDER INSTABILITY

Directory of Open Access Journals (Sweden)

Santosh Kumar

2015-06-01

, rest 14(40% patients had Left shoulder involved. The mean follow - up period was 12 months (range 8 - 28 months. The patients were evaluated by visual analogue score (VAS, ROWE’s score at final fo llow - up. RESULTS : 34/35 patient’s regained almost preoperative range of forward flexion at the last follow - up. Preoperative scores were compared with the most recent follow - up scores for all variables with the help of paired t test. All patients had significant improvement in visual analogue score and ROWE’s score. In the preoperative period 18(51.43% patients had full range and 14(48.57% patient had painful/limited terminal range of motion, as regards external rotation with arm at the side (ER1. A nd 07(20% patients had 0 - 65º, 22(62.85% patients had 0 - 70º, 3(8.57% patient had 0 - 70º with pain at terminal range of motion, 3(8.57% of patients had full range of motion, as regards external rotation at 90º abduction (ER2. At the last follow - up, 33/35 (94.28% patients had full range of ER1 & 32/35(91.42% patients had full range of ER2. This improvement in external rotation deficit was statistically significant (P <.05 . Preoperative scores were compared with the most recent follow - up scores for all var iables with the help of paired t test. Three of the patients developed apprehension which got resolved after proper physiotherapy. Pre - operative: mean Total Rowe score was 48.51, mean scores of stability 21.17, mean score of function 12.14, mean score of motion 15.77. The mean post - operative Rowe score improved to 97.63, mean stability component to 47.77, mean motion component to19.47 and mean function component to 28.63 compared to the pre - operative Rowe scores. We had final Rowe’s Score excelle nt in 32 patients, good in 2 and fair in 1 and Poor in 1 (P - value 2.992X10 - 12 . There was no radiological evidence of loosening and migration of anchors or any gleno - humeral arthritis on subsequent follow - up skiagrams in any of our patients

A group of 20 stone anchors from the waters of Dwarka, on the Gujarat Coast, India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S; Sundaresh; Tripati, S.; Gudigar, P.; Vora, K.H.; Bandodkar, S.N.

A large number of stone anchors were discovered in a water depth of 10-14 m off Dwarka during the 1998-99 season. The seabed near the anchors consists of a ledge with an average height of 1 m. Several anchors were found trapped between the rocks...

Membrane curvature enables N-Ras lipid anchor sorting to liquid-ordered membrane phases

DEFF Research Database (Denmark)

Larsen, Jannik Bruun; Jensen, Martin Borch; Bhatia, Vikram Kjøller

2015-01-01

Trafficking and sorting of membrane-anchored Ras GTPases are regulated by partitioning between distinct membrane domains. Here, in vitro experiments and microscopic molecular theory reveal membrane curvature as a new modulator of N-Ras lipid anchor and palmitoyl chain partitioning. Membrane...

Talar anchor placement for modified Brostrom lateral ankle stabilization procedure.

Science.gov (United States)

Angirasa, Arush K; Barrett, Michael J

2008-01-01

The modified Brostrom procedure has been a proven procedure with excellent utility in the treatment of lateral ankle instability within limitation. Multiple variations of the original technique have been described in the literature to date. Included in these variations are differences in anchor placement, suture technique, or both. In this research study, we propose placing a bone screw anchor into the lateral shoulder of the talus rather than the typical placement at the lateral malleolus for anatomic reconstruction of the lateral ankle ligaments.

Career Anchors: A New Concept in Career Development for the Professional Educator.

Science.gov (United States)

DeLong, Thomas J.

Created by Dr. Edgar Schein of the Massachusetts Institute of Technology (MIT), the career anchor model suggests that certain motivational/talent/value drives, formed through work experience, function to guide and constrain entire careers; and that such anchors are the source of stability that permits growth and change in other areas. The concept…

The Double-Anchoring Theory of Lightness Perception: A Comment on Bressan (2006)

Science.gov (United States)

Howe, Piers D. L.; Sagreiya, Hersh; Curtis, Dwight L.; Zheng, Chengjie; Livingstone, Margaret S.

2007-01-01

Comments on an article by Bressan. Recently, a double-anchoring theory (DAT) of lightness perception was proposed (P. Bressan, 2006), which offers explanations for all the data explained by the original anchoring theory (A. Gilchrist et al., 1999), as well as a number of additional lightness phenomena. Consequently, DAT can account for an…

Highly Dispersed Nickel-Containing Mesoporous Silica with Superior Stability in Carbon Dioxide Reforming of Methane: The Effect of Anchoring

Directory of Open Access Journals (Sweden)

Wenjia Cai

2014-03-01

Full Text Available A series of nickel-containing mesoporous silica samples (Ni-SiO2 with different nickel content (3.1%–13.2% were synthesized by the evaporation-induced self-assembly method. Their catalytic activity was tested in carbon dioxide reforming of methane. The characterization results revealed that the catalysts, e.g., 6.7%Ni-SiO2, with highly dispersed small nickel particles, exhibited excellent catalytic activity and long-term stability. The metallic nickel particle size was significantly affected by the metal anchoring effect between metallic nickel particles and unreduced nickel ions in the silica matrix. A strong anchoring effect was suggested to account for the remaining of small Ni particle size and the improved catalytic performance.

Research on Anchorage Performance of Grouting Anchor Connection of Precast Concrete Structure

Science.gov (United States)

Wang, Donghui; Liu, Xudong; Wang, Sheng; Cao, Xixi

2018-03-01

The bonding of grouted anchor bars is one of the vertical connection forms of steel bars in fabricated concrete structures. The performance of grouted connection is mainly affected by the anchorage length and lap length of steel bars. The mechanisms of bond and anchorage between steel bar and concrete are analyzed, and the factors that influence the anchorage performance of steel bar are systematically summarized. Results show that the bond and anchorage performance of steel and concrete have been studied widely, but there are still shortcomings, and the connection forms need to be further improved.

Test on the splitting failure capacity of the bottom rail due to uplift in partially anchored shear walls

OpenAIRE

Caprolu, Giuseppe; Girhammar, Ulf Arne; Källsner, Bo; Johnsson, Helena

2012-01-01

Källsner and Girhammar have developed a new plastic design method for wood-frame shear walls at ultimate limit state. The method is capable of calculating the load-carrying capacity of partially anchored shear walls, where the leading stud is not necessarily anchored against uplift. In fully anchored shear walls, the leading stud needs to be anchored using some kind of hold-downs to resist uplift and the bottom rail needs to be fixed by anchor bolts to resist horizontal shear forces. In parti...

Successful bone-anchored hearing aid implantation in a patient with osteogenesis imperfecta.

Science.gov (United States)

Coutinho, M B; Marques, C; Mendes, G J; Gonçalves, C

2015-11-01

To report a case of successful bone-anchored hearing aid implantation in an adult patient with type III osteogenesis imperfecta, which is commonly regarded as a contraindication to this procedure. A 45-year-old man with type III osteogenesis imperfecta presented with mixed hearing loss. There was a mild sensorineural component in both ears, with an air-bone gap between 45 and 50 dB HL. He was implanted with a bone-anchored hearing aid. The audiological outcome was good, with no complications and good implant stability (as measured by resonance frequency analysis). To our knowledge, this is the first recorded case of bone-anchored hearing aid implantation in a patient with osteogenesis imperfecta.

Traction endurance biomechanical study of metallic suture anchors at different insertion angles

Directory of Open Access Journals (Sweden)

Azato Flávia Namie

2003-01-01

Full Text Available The suture anchors' insertion angle and its traction resistance are the main subjects of this study. Twenty trials were realized using threaded suture anchors in four diferents angulations (30º /45º /60º /90º in human bone (distal femur and another twenty trials in artificial bone (SawboneTM. The anchors were pulled out being tractioned uprightly from its bone surface by a Kratos Universal test machine. The human bone results found no relation between the main subjects of this study, so whithout statistical value. On the other hand at the artificial bone the insertion angle of 90º beared more traction, being statistically significant compared to the other angles.

Experience-based, body-anchored qualitative research interviewing

DEFF Research Database (Denmark)

Stelter, Reinhard

2010-01-01

-anchored interviewing, and second, by an interview guide that explores a research participant's personal experience with mindfulness meditation. An excerpt from an interview is discussed to illustrate the advantages of this interview form, namely its value as a methodological instrument for qualitative research...

Extrusion of bone anchor suture following flexor digitorum profundus tendon avulsion injury repair.

LENUS (Irish Health Repository)

Tiong, William H C

2011-09-01

Flexor digitorum profundus (FDP) zone I tendon avulsion injury is traditionally repaired with a pullout suture technique. More recently, bone anchor sutures have been used as a viable alternative and have largely replaced areas in hand surgery where pullout suture technique was once required. To date, there have been very few complications reported related to bone anchor suture use in FDP tendon reattachment to the bone. We report a very unusual case of extrusion of bone anchor through the nailbed, 6 years after zone I FDP tendon avulsion injury repair and a brief review of literature.

The anchoring mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.

2014-09-01

The objective of this work is to investigate the mechanism of the laminar premixed flame anchoring near a heat-conducting bluff-body. We use unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. No artificial flame anchoring boundary conditions were imposed. Simulations show a shear-layer stabilized flame just downstream of the bluff-body, with a recirculation zone formed by the products of combustion. A steel bluff-body resulted in a slightly larger recirculation zone than a ceramic bluff-body; the size of which grew as the equivalence ratio was decreased. A significant departure from the conventional two-zone flame-structure is shown in the anchoring region. In this region, the reaction zone is associated with a large negative energy convection (directed from products to reactants) resulting in a negative flame-displacement speed. It is shown that the premixed flame anchors at an immediate downstream location near the bluff-body where favorable ignition conditions are established; a region associated with (1) a sufficiently high temperature impacted by the conjugate heat exchange between the heat-conducting bluff-body and the hot reacting flow and (2) a locally maximum stoichiometry characterized by the preferential diffusion effects. © 2014 The Combustion Institute.

Reinforcement mechanism of multi-anchor wall with double wall facing

Science.gov (United States)

Suzuki, Kouta; Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo

2017-10-01

The reinforced soil wall has high seismic performance as generally known. However, the seismic behavior has not been clarified accurately yet, especially on multi-anchor wall with double wall facing. Indefinite behavior of reinforced soil wall during earthquake make us complicated in case with adopting to the abutment, because of arrangement of anchor plate as reinforcement often different according to the width of roads. In this study, a series of centrifuge model tests were carried out to investigate the reinforcement mechanism of multi anchor wall with double wall facing from the perspective of the vertical earth pressure. Several types of reinforce arrangement and rigid wall were applied in order to verify the arch function in the reinforced regions. The test results show unique behavior of vertical earth pressure, which was affected by arch action. All the vertical earth pressure placed behind facing panel, are larger than that of middle part between facing panel despite of friction between backfill and facing panel. Similar results were obtained in case using rigid wall. On the other hands, the vertical earth pressure, which were measured at the 3cm high from bottom of model container, shows larger than that of bottom. This results show the existence of arch action between double walls. In addition, it implies that the wall facing of such soil structure confined the backfill as pseudo wall, which is very reason that the multi anchor wall with double wall facing has high seismic performance.

National Needs for Appearance Metrology

Science.gov (United States)

Nadal, Maria E.

2003-04-01

Appearance greatly influences a customer's judgement of the quality and acceptability of manufactured products, as yearly there is approximately $700 billion worth of shipped goods for which overall appearance is critical to their sale. For example, appearance is reported to be a major factor in about half of automobile purchases. The appearance of an object is the result of a complex interaction of the light field incident upon the object, the scattering and absorption properties of the object, and human perception. The measurable attributes of appearance are divided into color (hue, saturation, and lightness) and geometry (gloss, haze). The nature of the global economy has increased international competition and the need to improve the quality of many manufactured products. Since the manufacturing and marketing of these products is international in scope, the lack of national appearance standard artifacts and measurement protocols results in a direct loss to the supplier. One of the primary missions of the National Institute of Standards and Technology (NIST) is to strengthen the U.S. economy by working with industry to develop and apply technology, measurements and standards. The NIST Physics Laboratory has established an appearance metrology laboratory. This new laboratory provides calibration services for 0^o/45^o color standards and 20^o°, 60^o°, and 85^o° specular gloss, and research in the colorimetric characterization of gonioapparent including a new Standard Reference Material for metallic coatings (SRM 2017) and measurement protocols for pearlescent coatings. These services are NIST's first appearance metrology efforts in many years; a response to needs articulated by industry. These services are designed to meet demands for improved measurements and standards to enhance the acceptability of final products since appearance often plays a major role in their acceptability.

Fullerene-based Anchoring Groups for Molecular Electronics

DEFF Research Database (Denmark)

Martin, Christian A.; Ding, Dapeng; Sørensen, Jakob Kryger

2008-01-01

We present results on a new fullerene-based anchoring group for molecular electronics. Using lithographic mechanically controllable break junctions in vacuum we have determined the conductance and stability of single-molecule junctions of 1,4-bis(fullero[c]pyrrolidin-1-yl)benzene. The compound can...

Bone-anchored titanium implants for auricular rehabilitation: case report and review of literature.

Science.gov (United States)

Gumieiro, Emne Hammoud; Dib, Luciano Lauria; Jahn, Ricardo Schmitutz; Santos Junior, João Ferreira dos; Nannmark, Ulf; Granström, Gösta; Abrahão, Márcio

2009-01-01

Osseointegrated implants have acquired an important role in the prosthetic rehabilitation of patients with craniofacial defects. The main indications are lack of local tissue for autogenous reconstruction, previous reconstruction failure and selection of this technique by the patient. This paper presents a clinical case and discusses indications and advantages of the osseointegrated implant technique for retention of auricular prostheses. Case report, Universidade Federal de São Paulo (UNIFESP). A female patient received three auricular implants after surgical resection of a hemangioma in her left ear. The time taken for osseointegration of the temporal bone was three months. After fabrication of the implant-retained auricular prosthesis, the patient was monitored for 12 months. The clinical parameters evaluated showed good postoperative healing, healthy peri-implant tissue, good hygiene and no loss of implants. Good hygiene combined with thin and immobile peri-implant soft tissues resulted in minimal complications. Craniofacial implant integration appears to be site-dependent; increasing age affects osseointegration in the temporal bone. The frequency of adverse skin reactions in peri-implant tissues is generally low. The surgical technique for rehabilitation using implant-retained auricular prostheses seems to be simple. It is associated with low rates of adverse skin reactions and long-term complications. Prostheses anchored by osseointegrated implants seem to provide better retention than do prostheses supported on spectacle frames, less risk of discoloration through the use of adhesives and better esthetic results than do prostheses anchored in the surgical cavity.

The Place of White in a World of Grays: A Double-Anchoring Theory of Lightness Perception

Science.gov (United States)

Bressan, Paola

2006-01-01

The specific gray shades in a visual scene can be derived from relative luminance values only when an anchoring rule is followed. The double-anchoring theory I propose in this article, as a development of the anchoring theory of Gilchrist et al. (1999), assumes that any given region (a) belongs to one or more frameworks, created by Gestalt…

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

International Nuclear Information System (INIS)

Wang, Jimin; Li, Yue; Modis, Yorgo

2014-01-01

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. - Highlights: • Structures of pestivirus E2 proteins impose constraints on E1, E2 membrane anchors. • Atomic models of the E1 and E2 membrane anchors were generated in silico. • A “snorkeling” arginine completes the short helical hairpin in the E2 membrane anchor. • Roles in pH sensing and E1–E2 disulfide bond formation are proposed for E1 residues. • Implications for E1 ectodomain structure and disulfide bonding pattern are discussed

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

Energy Technology Data Exchange (ETDEWEB)

Wang, Jimin, E-mail: jimin.wang@yale.edu; Li, Yue; Modis, Yorgo, E-mail: yorgo.modis@yale.edu

2014-04-15

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. - Highlights: • Structures of pestivirus E2 proteins impose constraints on E1, E2 membrane anchors. • Atomic models of the E1 and E2 membrane anchors were generated in silico. • A “snorkeling” arginine completes the short helical hairpin in the E2 membrane anchor. • Roles in pH sensing and E1–E2 disulfide bond formation are proposed for E1 residues. • Implications for E1 ectodomain structure and disulfide bonding pattern are discussed.

Two endoplasmic reticulum (ER) membrane proteins that facilitate ER-to-Golgi transport of glycosylphosphatidylinositol-anchored proteins.

Science.gov (United States)

Barz, W P; Walter, P

1999-04-01

Many eukaryotic cell surface proteins are anchored in the lipid bilayer through glycosylphosphatidylinositol (GPI). GPI anchors are covalently attached in the endoplasmic reticulum (ER). The modified proteins are then transported through the secretory pathway to the cell surface. We have identified two genes in Saccharomyces cerevisiae, LAG1 and a novel gene termed DGT1 (for "delayed GPI-anchored protein transport"), encoding structurally related proteins with multiple membrane-spanning domains. Both proteins are localized to the ER, as demonstrated by immunofluorescence microscopy. Deletion of either gene caused no detectable phenotype, whereas lag1Delta dgt1Delta cells displayed growth defects and a significant delay in ER-to-Golgi transport of GPI-anchored proteins, suggesting that LAG1 and DGT1 encode functionally redundant or overlapping proteins. The rate of GPI anchor attachment was not affected, nor was the transport rate of several non-GPI-anchored proteins. Consistent with a role of Lag1p and Dgt1p in GPI-anchored protein transport, lag1Delta dgt1Delta cells deposit abnormal, multilayered cell walls. Both proteins have significant sequence similarity to TRAM, a mammalian membrane protein thought to be involved in protein translocation across the ER membrane. In vivo translocation studies, however, did not detect any defects in protein translocation in lag1Delta dgt1Delta cells, suggesting that neither yeast gene plays a role in this process. Instead, we propose that Lag1p and Dgt1p facilitate efficient ER-to-Golgi transport of GPI-anchored proteins.

Unlocking Hospitality Managers Career Transitions through Applying Schein's Career Anchors Theory

Science.gov (United States)

McGuire, David; Polla, Giovana; Heidl, Britta

2017-01-01

Purpose: This paper seeks to unlock the career transitions of hospitality managers through applying Schein's career anchors theory. It seeks to understand how Schein's Career Anchors help explain the career transitions of managers in the Scottish hospitality industry. Design/methodology/approach: The paper adopts a non-sequential multi-method…

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors.

Science.gov (United States)

Bester, C L; Mouton, T

2006-08-01

In order to contribute to higher levels of job satisfaction, job involvement and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual's set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one's occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect that it is likely that their dominant career anchor would be service orientation. If this is the case, psychologists with service as their dominant career anchor are supposed to have greater job satisfaction and job involvement compared to those with different career anchors. However, according to literature, this assumption is not necessarily correct. The primary goals of the current study were to determine whether in fact service is the dominant career anchor of psychologists in the Free State and whether there are significant differences regarding job satisfaction and job involvement between psychologists with and without service as their dominant career anchor. A third goal was to determine whether psychologists with different dominant career anchors differ significantly from one another regarding job satisfaction and job involvement. Questionnaires measuring career orientations, job satisfaction and job involvement were sent to 165 of the 171 registered psychologists in the Free State region. Only 75 psychologists (45,5%) responded which exceeded the traditional return rate of 20 to 30%. Due to the small sample of respondents, a nonparametric statistical test, namely the Mann Whitney U test was conducted to determine possible differences. An analysis of the data showed that 21 respondents had entrepreneurship as their dominant career orientation while 12 fell in the technical/functional, 12 in the challenging, 9 in the service and 8 in the autonomy categories of dominant

Controlling the Anchoring Effect through Transcranial Direct Current Stimulation (tDCS to the Right Dorsolateral Prefrontal Cortex

Directory of Open Access Journals (Sweden)

Jianbiao Li

2017-06-01

Full Text Available Selective accessibility mechanisms indicate that anchoring effects are results of selective retrieval of working memory. Neuroimaging studies have revealed that the right dorsolateral prefrontal cortex (DLPFC is closely related to memory retrieval and performance. However, no research has investigated the effect of changing the cortical excitability in right DLPFC on anchoring effects. Transcranial direct current stimulation (tDCS can modulate the excitability of the human cerebral cortex, while anodal and cathodal tDCS are postulated to increase or decrease cortical activity, respectively. In this study, we used tDCS to investigate whether effects of increased or decreased right DLPFC excitability influence anchoring effects in willingness to pay (WTP experiments. Ninety participants were first randomly assigned to receive either anodal, cathodal, or sham stimulation of 15 min, then they performed a valuation task regarding WTP. The results showed that anchoring effects were negatively related to activities of right DLPFC: the anodal stimulation diminished anchoring effects while the cathodal stimulation increased anchoring effects. These outcomes provide one of the first instances of neural evidence for the role of the right DLPFC in anchoring effects and support psychological explanations of the selective accessibility mechanisms and cognitive sets.

Anchor-dependent lipofection with non-glycerol based cytofectins containing single 2-hydroxyethyl head groups.

Science.gov (United States)

Venkata Srilakshmi, Gollapudi; Sen, Joyeeta; Chaudhuri, Arabinda; Ramadas, Yerramsetti; Madhusudhana Rao, Nalam

2002-02-15

Detailed structure-activity investigations aimed at probing the anchor chain length dependency for glycerol-based lipofectins have been reported previously. Herein, we report on the first detailed investigation on the anchor-dependent transfection biology of non-glycerol based simple monocationic cytofectins containing single 2-hydroxyethyl head group functionality using 11 new structural analogs of our previously published first generation of non-glycerol based transfection lipids (lipids 1-11). The C-14 and C-16 analogs of DOMHAC (lipids 4 and 5, respectively) were found to be remarkably efficient in transfecting COS-1 cells. In addition, the present anchor-dependency investigation also revealed that the C-14 analog of DOHEMAB (lipid 10) is significantly efficient in transfecting both COS-1 and NIH3T3 cells. Our results also indicate that too strong lipid-DNA interactions might result in weaker transfection for non-glycerol based cationic lipids. In summary, the anchor-dependence investigations presented here convincingly demonstrate that non-glycerol based cationic lipids containing a single hydroxyethyl head group and hydrophobic C-14 or C-16 anchors are promising non-toxic cationic transfection lipids for future use in liposomal gene delivery.

Enhanced Charge Separation Efficiency in Pyridine-Anchored Phthalocyanine-Sensitized Solar Cells by Linker Elongation.

Science.gov (United States)

Ikeuchi, Takuro; Agrawal, Saurabh; Ezoe, Masayuki; Mori, Shogo; Kimura, Mutsumi

2015-11-01

A series of zinc phthalocyanine sensitizers (PcS22-24) having a pyridine anchoring group are designed and synthesized to investigate the structural dependence on performance in dye-sensitized solar cells. The pyridine-anchor zinc phthalocyanine sensitizer PcS23 shows 79 % incident-photon to current-conversion efficiency (IPCE) and 6.1 % energy conversion efficiency, which are comparable with similar phthalocyanine dyes having a carboxylic acid anchoring group. Based on DFT calculations, the high IPCE is attributed with the mixture of an excited-state molecular orbital of the sensitizer and the orbitals of TiO2 . Between pyridine and carboxylic acid anchor dyes, opposite trends are observed in the linker-length dependence of the IPCE. The red-absorbing PcS23 is applied for co-sensitization with a carboxyl-anchor organic dye D131 that has a complementary spectral response. The site-selective adsorption of PcS23 and D131 on the TiO2 surface results in a panchromatic photocurrent response for the whole visible-light region of sun light. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Proteome analysis of Aspergillus fumigatus identifies glycosylphosphatidylinositol-anchored proteins associated to the cell wall biosynthesis.

Science.gov (United States)

Bruneau, J M; Magnin, T; Tagat, E; Legrand, R; Bernard, M; Diaquin, M; Fudali, C; Latgé, J P

2001-08-01

Previous studies in Aspergillus fumigatus (Mouyna I., Fontaine T., Vai M., Monod M., Fonzi W. A., Diaquin M., Popolo L., Hartland R. P., Latgé J.-P, J. Biol. Chem. 2000, 275, 14882-14889) have shown that a glucanosyltransferase playing an important role in fungal cell wall biosynthesis is glycosylphosphatidylinositol (GPI) anchored to the membrane. To identify other GPI-anchored proteins putatively involved in cell wall biogenesis, a proteomic analysis has been undertaken in A. fumigatus and the protein data were matched with the yeast genomic data. GPI-anchored proteins of A. fumigatus were released from membrane preparation by an endogenous GPI-phospholipase C, purified by liquid chromatography and separated by two-dimensional electrophoresis. They were characterized by their peptide mass fingerprint through matrix-assisted laser desorption/ionization-time of flight-(MALDI-TOF)-mass spectrometry and by internal amino acid sequencing. Nine GPI-anchored proteins were identified in A. fumigatus. Five of them were homologs of putatively GPI-anchored yeast proteins (Csa1p, Crh1p, Crh2p, Ecm33p, Gas1p) of unknown function but shown by gene disruption analysis to play a role in cell wall morphogenesis. In addition, a comparative study performed with chitin synthase and glucanosyl transferase mutants of A. fumigatus showed that a modification of the growth phenotype seen in these mutants was associated to an alteration of the pattern of GPI-anchored proteins. These results suggest that GPI-anchored proteins identified in this study are involved in A. fumigatus cell wall organization.

Nominal Anchors in the CIS

OpenAIRE

Peter M Keller; Thomas J Richardson

2003-01-01

Monetary policy has become increasingly important in the countries of the Commonwealth of Independent States (CIS) as fiscal adjustment and structural reforms have taken root. Inflation has been brought down to relatively low levels in almost all of these countries, raising the question of what should be the appropriate nominal anchor at this stage. Formally, almost all CIS countries have floating exchange rate regimes, yet in practice they manage their exchange rates very heavily, perhaps be...

Geometric nonlinear analysis of self-anchored cable-stayed suspension bridges.

Science.gov (United States)

Hui-Li, Wang; Yan-Bin, Tan; Si-Feng, Qin; Zhe, Zhang

2013-01-01

Geometric nonlinearity of self-anchored cable-stayed suspension bridges is studied in this paper. The repercussion of shrinkage and creep of concrete, rise-to-span ratio, and girder camber on the system is discussed. A self-anchored cable-stayed suspension bridge with a main span of 800 m is analyzed with linear theory, second-order theory, and nonlinear theory, respectively. In the condition of various rise-to-span ratios and girder cambers, the moments and displacements of both the girder and the pylon under live load are acquired. Based on the results it is derived that the second-order theory can be adopted to analyze a self-anchored cable-stayed suspension bridge with a main span of 800 m, and the error is less than 6%. The shrinkage and creep of concrete impose a conspicuous impact on the structure. And it outmatches suspension bridges for system stiffness. As the rise-to-span ratio increases, the axial forces of the main cable and the girder decline. The system stiffness rises with the girder camber being employed.

Geometric Nonlinear Analysis of Self-Anchored Cable-Stayed Suspension Bridges

Directory of Open Access Journals (Sweden)

Wang Hui-Li

2013-01-01

Full Text Available Geometric nonlinearity of self-anchored cable-stayed suspension bridges is studied in this paper. The repercussion of shrinkage and creep of concrete, rise-to-span ratio, and girder camber on the system is discussed. A self-anchored cable-stayed suspension bridge with a main span of 800 m is analyzed with linear theory, second-order theory, and nonlinear theory, respectively. In the condition of various rise-to-span ratios and girder cambers, the moments and displacements of both the girder and the pylon under live load are acquired. Based on the results it is derived that the second-order theory can be adopted to analyze a self-anchored cable-stayed suspension bridge with a main span of 800 m, and the error is less than 6%. The shrinkage and creep of concrete impose a conspicuous impact on the structure. And it outmatches suspension bridges for system stiffness. As the rise-to-span ratio increases, the axial forces of the main cable and the girder decline. The system stiffness rises with the girder camber being employed.

Impingement syndrome of the shoulder following double row suture anchor technique for arthroscopic rotator cuff repair: a case report

Directory of Open Access Journals (Sweden)

Rambani Rohit

2009-06-01

Full Text Available Abstract Introduction Arthroscopic repair of the rotator cuff is a demanding surgery. Accurate placement of anchors is key to success. Case presentation A 38-year-old woman received arthroscopic repair of her rotator cuff using a double row suture anchor technique. Postoperatively, she developed impingement syndrome which resulted from vertical displacement of a suture anchor once the shoulder was mobilised. The anchor was removed eight weeks following initial surgery and the patient had an uneventful recovery. Conclusion Impingement syndrome following arthroscopic repair of the rotator cuffs using double row suture anchor has not been widely reported. This is the first such case where anchoring has resulted in impingement syndrome.

Study of the interaction of the rupture zones of contiguous anchor plates in analogical medium

Directory of Open Access Journals (Sweden)

Abbad H.

2018-01-01

Full Text Available Knowing what occurs above anchor plates is certainly instructive. In this general vision of the interaction soil-anchor plates that our work was directed. An experimental study which required the design and implantation of a model containing plastic granules powder to similate a natural environment, is presented. The latter is subjected to the removal of anchor paltes. For each test, digital photographs are taken to materialize different deformed configurations during the pullout process. These photos processed in couples by the 7D software (image correlation giving the evolution of the displacement field and plane strain analogical environment. Particular attention is paid to the discussion of the interference of rupture zones of contiguous anchors by reducing the distance between plates.

Career Anchors and the Effects of Downsizing: Implications for Generations and Cultures at Work. A Preliminary Investigation.

Science.gov (United States)

Marshall, Verena; Bonner, Dede

2003-01-01

The relationships among career anchors, age, culture, gender, employment experience, and the impact of career planning on downsizing were examined with data from 423 management students (49% had been downsized). Lifestyle was the most valued anchor across age groups, stability/security the least; compared with Schein's earlier anchors research,…

The count of losses by eddy currents in the windings of electric motors with hollow anchor

Directory of Open Access Journals (Sweden)

N. V. Pribylova

2017-01-01

Full Text Available Given the rationale of taking into account losses on eddy currents in the windings of a low-inertia DC motors with offered magnetoelectric systems. Increased in recent years, the power of these motors (through the use of highly coercive magnets permanent caused an increase in the volume of copper in the air gap and the magnetic induction values. All this has values given rise to significant eddy currents in the windings made in the air gap, and hence the necessity of taking into account losses from these currents. The experimentally obtained dependence of the losses on eddy currents on the frequency of rotation for a DC motor with a hollow anchor with a power of 350 watts. The magnitude of these losses can reach 30% of the nominal power of the motor. Described mechanism of occurrence of losses. Eddy currents occur in areas with variable magnetic flux and cause the appearance of force, which is directed toward the velocity vector and inhibits the anchor. The directions of these currents, the vectors of magnetic induction, magnetic field and force acting on the conductor winding and a braking anchor. The proposed methods reduce losses: crushing contours of eddy currents and achieve uniform distribution of magnetic induction in the interpolar space of the motor. Shows their strengths and weaknesses. The crushing circuits of windings occur surge currents. To eliminate the losses on the surge currents it is necessary to apply a transposition of the conductors. Given a refined formula for finding the losses on eddy currents in the armature winding, the conductors of which is made in the form of a harness of several wires. Formula has shown a good convergence with experimental data.

Amplatzer Vascular Plug Anchoring Technique to Stabilize the Delivery System for Microcoil Embolization

International Nuclear Information System (INIS)

Onozawa, Shiro; Murata, Satoru; Mine, Takahiko; Sugihara, Fumie; Yasui, Daisuke; Kumita, Shin-ichiro

2016-01-01

PurposeTo evaluate the feasibility of a novel embolization technique, the Amplatzer vascular plug (AVP) anchoring technique, to stabilize the delivery system for microcoil embolization.Materials and methodsThree patients were enrolled in this study, including two cases of internal iliac artery aneurysms and one case of internal iliac arterial occlusion prior to endovascular aortic repair. An AVP was used in each case for embolization of one target artery, and the AVP was left in place. The AVP detachment wire was then used as an anchor to stabilize the delivery system for microcoil embolization to embolize the second target artery adjacent to the first target artery. The microcatheter for the microcoils was inserted parallel to the AVP detachment wire in the guiding sheath or catheter used for the AVP.ResultsThe AVP anchoring technique was achieved and the microcatheter was easily advanced to the second target artery in all three cases.ConclusionThe AVP anchoring technique was found to be feasible to advance the microcatheter into the neighboring artery of an AVP-embolized artery.

Proposed Methodology for Design of Carbon Fiber Reinforced Polymer Spike Anchors into Reinforced Concrete

Energy Technology Data Exchange (ETDEWEB)

MacFarlane, Eric Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-05-26

The included methodology, calculations, and drawings support design of Carbon Fiber Reinforced Polymer (CFRP) spike anchors for securing U-wrap CFRP onto reinforced concrete Tbeams. This content pertains to an installation in one of Los Alamos National Laboratory’s facilities. The anchors are part of a seismic rehabilitation to the subject facility. The information contained here is for information purposes only. The reader is encouraged to verify all equations, details, and methodology prior to usage in future projects. However, development of the content contained here complied with Los Alamos National Laboratory’s NQA-1 quality assurance program for nuclear structures. Furthermore, the formulations and details came from the referenced published literature. This literature represents the current state of the art for FRP anchor design. Construction personnel tested the subject anchor design to the required demand level demonstrated in the calculation. The testing demonstrated the ability of the anchors noted to carry loads in excess of 15 kips in direct tension. The anchors were not tested to failure in part because of the hazards associated with testing large-capacity tensile systems to failure. The calculation, methodology, and drawing originator was Eric MacFarlane of Los Alamos National Laboratory’s (LANL) Office of Seismic Hazards and Risk Mitigation (OSHRM). The checker for all components was Mike Salmon of the LANL OSHRM. The independent reviewers of all components were Insung Kim and Loring Wyllie of Degenkolb Engineers. Note that Insung Kim contributed to the initial formulations in the calculations that pertained directly to his Doctoral research.

Task difficulty has no effect on haptic anchoring during tandem walking in young and older adults.

Science.gov (United States)

Costa, Andréia Abud da Silva; Santos, Luciana Oliveira Dos; Mauerberg-deCastro, Eliane; Moraes, Renato

2018-02-14

This study assessed the contribution of the "anchor system's" haptic information to balance control during walking at two levels of difficulty. Seventeen young adults and seventeen older adults performed 20 randomized trials of tandem walking in a straight line, on level ground and on a slightly-raised balance beam, both with and without the use of the anchors. The anchor consists of two flexible cables, whose ends participants hold in each hand, to which weights (125 g) are attached at the opposing ends, and which rest on the ground. As the participants walk, they pull on the cables, dragging the anchors. Spatiotemporal gait variables (step speed and single- and double-support duration) were processed using retro-reflective markers on anatomical sites. An accelerometer positioned in the cervical region registered trunk acceleration. Walking on the balance beam increased single- and double-support duration and reduced step speed in older adults, which suggests that this condition was more difficult than walking on the level ground. The anchors reduced trunk acceleration in the frontal plane, but the level of difficulty of the walking task showed no effect. Thus, varying the difficulty of the task had no influence on the way in which participants used the anchor system while tandem walking. The older adults exhibited more difficulty in walking on the balance beam as compared to the younger adults; however, the effect of the anchor system was similar in both groups. Copyright © 2017 Elsevier B.V. All rights reserved.

Final Technical Report Advanced Anchoring Technology DOE Award Number DE-EE0003632 Project Period 09/10 - 09/12

Energy Technology Data Exchange (ETDEWEB)

Meggitt, Dallas J

2012-11-09

It is generally conceded that the costs associated with current practices for the mooring, anchoring, or foundation systems of Marine HydroKinetic (MHK) and Deepwater Floating Wind systems are a disproportionate portion of the total cost of an installed system. Reducing the cost of the mooring and anchoring components for MHK systems can contribute substantially to reducing the levelized cost of electricity (LCOE). Micropile anchors can reduce the LCOE both directly, because the anchors, associated mooring hardware and installation costs are less than conventional anchor and mooring systems, but also because micropile anchors require less extensive geotechnical surveys for confident design and proper implementation of an anchor or foundation system. This report presents the results of the development of critical elements of grouted marine micropile anchor (MMA) technology for application to MHK energy conversion systems and other ocean engineering applications that require fixing equipment to the seafloor. Specifically, this project identified grout formulations and developed designs for grout dispensing systems suitable for use in a seawater environment as a critical development need for successful implementation of practical MMA systems. The project conducted a thorough review of available information on the use of cement-based grouts in seawater. Based on this review and data available from commercial sources, the project selected a range of grout formulations for testing as part of a micropile system. The project also reviewed instrumentation for measuring grout density, pressure and flow rate, and integrated an instrumentation system suitable for use with micropile installation. The grout formulations and instrumentation system were tested successfully and demonstrated the suitability of MMA technology for implementation into anchor systems for MHK and other marine renewable energy systems. In addition, this project developed conceptual designs for micropile

SNP discovery and chromosome anchoring provide the first physically-anchored hexaploid oat map and reveal synteny with model species.

Directory of Open Access Journals (Sweden)

Rebekah E Oliver

Full Text Available A physically anchored consensus map is foundational to modern genomics research; however, construction of such a map in oat (Avena sativa L., 2n = 6x = 42 has been hindered by the size and complexity of the genome, the scarcity of robust molecular markers, and the lack of aneuploid stocks. Resources developed in this study include a modified SNP discovery method for complex genomes, a diverse set of oat SNP markers, and a novel chromosome-deficient SNP anchoring strategy. These resources were applied to build the first complete, physically-anchored consensus map of hexaploid oat. Approximately 11,000 high-confidence in silico SNPs were discovered based on nine million inter-varietal sequence reads of genomic and cDNA origin. GoldenGate genotyping of 3,072 SNP assays yielded 1,311 robust markers, of which 985 were mapped in 390 recombinant-inbred lines from six bi-parental mapping populations ranging in size from 49 to 97 progeny. The consensus map included 985 SNPs and 68 previously-published markers, resolving 21 linkage groups with a total map distance of 1,838.8 cM. Consensus linkage groups were assigned to 21 chromosomes using SNP deletion analysis of chromosome-deficient monosomic hybrid stocks. Alignments with sequenced genomes of rice and Brachypodium provide evidence for extensive conservation of genomic regions, and renewed encouragement for orthology-based genomic discovery in this important hexaploid species. These results also provide a framework for high-resolution genetic analysis in oat, and a model for marker development and map construction in other species with complex genomes and limited resources.

Anchors from Goa waters, central west coast of India: Remains of Goa's overseas trade contacts with Arabian countries and Portugal

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Gaur, A.S.; Sundaresh

iron anchors, five anchors are similar in shape and belong to the 16th-17th century, whereas the other two anchors are similar in shape and datable to the 18th century. None of the stone or iron anchors have been found with any datable context except...

Towards robot-assisted anchor deployment in beating-heart mitral valve surgery.

Science.gov (United States)

Cheng, Lingbo; Sharifi, Mojtaba; Tavakoli, Mahdi

2018-06-01

Beating-heart intracardiac surgery promises significant benefits for patients compared with cardiopulmonary bypass based procedures. However, the fast motions of the heart introduce serious challenges for surgeons. In this work, a new impedance-controlled master-slave telerobotic system is developed to help perform anchor deployment for mitral valve annuloplasty under the guidance of live ultrasound images of the heart. The proposed bilateral teleoperation system can both reflect the non-oscillatory portion of slave-heart tissue interaction force on the surgeon's hand as haptic feedback and implement rapid compensation for the beating heart's motion. The surgical task involves performing anchor deployment on a simulated moving heart tissue to evaluate the effectiveness of the proposed strategy for safely interacting with a moving organ. The results obtained show that the telerobotic system increases the success rate of anchor deployment by 100% and reduces the excess force application rate by 70% compared with manual attempts. Copyright © 2018 John Wiley & Sons, Ltd.

Career anchor profiles of a sample of business and professional women

Directory of Open Access Journals (Sweden)

Ronel Erwee

1990-06-01

Full Text Available The career anchors of a sample of 95 business and professional woman were studied by means of the Career Orientations Inventory (DeLong, 1982. The hierarchy of career anchors of the sample was as follows: Service, Variety, Security (job tenure, Managerial competence. Autonomy, Identity, Technical/functional competence, Entrepreneurship and Security (geographical location. A few significant differences in career anchors did occur between various occupational groups. The implicatons of these findings in terms of career management in organisations are discussed. Opsomming Die loopbaanankers van 'n steekproef van 95 sake- en beroepsvroue is bestudeer deur middel van die "Career Orientations Inventory" (DeLong, 1982. Die steekproef het die volgende hierargie van loopbaanankers getoon: Diens, Verskeidenheid, Sekuriteit (organisatories, Bestuursbevoegdheid, Outonomie, Identiteit, Tegnies/funksionele bevoegdheid, Entrepreneurskap en Sekuriteit (geografies. 'n Paar beduidende verskille in loopbaanankerprofiele het tussen die onderskeie beroepsgroepe voorgekom. Die implikasies van die bevindings ten opsigte van loopbaanbeplanning in ondernemings word bespreek.

Comparison of two bone anchored hearing instruments: BP100 and Ponto Pro

DEFF Research Database (Denmark)

Olsen, Steen Østergaard; Glad, Henrik; Nielsen, Lars Holme

2011-01-01

This study aimed at investigating if there were differences in auditory performance, operation, or user preference between the Ponto Pro or the BP100, two bone anchored hearing instruments (BAHI) with modern sound processing technology.......This study aimed at investigating if there were differences in auditory performance, operation, or user preference between the Ponto Pro or the BP100, two bone anchored hearing instruments (BAHI) with modern sound processing technology....

Direct visualization of membrane architecture of myelinating cells in transgenic mice expressing membrane-anchored EGFP.

Science.gov (United States)

Deng, Yaqi; Kim, BongWoo; He, Xuelian; Kim, Sunja; Lu, Changqing; Wang, Haibo; Cho, Ssang-Goo; Hou, Yiping; Li, Jianrong; Zhao, Xianghui; Lu, Q Richard

2014-04-01

Myelinogenesis is a complex process that involves substantial and dynamic changes in plasma membrane architecture and myelin interaction with axons. Highly ramified processes of oligodendrocytes in the central nervous system (CNS) make axonal contact and then extrapolate to wrap around axons and form multilayer compact myelin sheathes. Currently, the mechanisms governing myelin sheath assembly and axon selection by myelinating cells are not fully understood. Here, we generated a transgenic mouse line expressing the membrane-anchored green fluorescent protein (mEGFP) in myelinating cells, which allow live imaging of details of myelinogenesis and cellular behaviors in the nervous systems. mEGFP expression is driven by the promoter of 2'-3'-cyclic nucleotide 3'-phosphodiesterase (CNP) that is expressed in the myelinating cell lineage. Robust mEGFP signals appear in the membrane processes of oligodendrocytes in the CNS and Schwann cells in the peripheral nervous system (PNS), wherein mEGFP expression defines the inner layers of myelin sheaths and Schmidt-Lanterman incisures in adult sciatic nerves. In addition, mEGFP expression can be used to track the extent of remyelination after demyelinating injury in a toxin-induced demyelination animal model. Taken together, the membrane-anchored mEGFP expression in the new transgenic line would facilitate direct visualization of dynamic myelin membrane formation and assembly during development and process remodeling during remyelination after various demyelinating injuries.

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors

Directory of Open Access Journals (Sweden)

CL Bester

2006-09-01

Full Text Available In order to contribute to higher levels of job satisfaction, job involvement , and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual’s set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one’s occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect that it is likely that their dominant career anchor would be service orientation. If this is the case, psychologists with service as their dominant career anchor are supposed to have greater job satisfaction and job involvement compared to those with different career anchors. However, according to literature, this assumption is not necessarily correct. The primary goals of the current study were to determine whether in fact service is the dominant career anchor of psychologists in the Free State and whether there are significant differences regarding job satisfaction and job involvement between psychologists with and without service as their dominant career anchor. A third goal was to determine whether psychologists with different dominant career anchors differ significantly from one another regarding job satisfaction and job involvement. Questionnaires measuring career orientations, job satisfaction and job involvement were sent to 165 of the 171 registered psychologists in the Free State region. Only 75 psychologists (45,5% responded which exceeded the traditional return rate of 20 to 30%. Due to the small sample of respondents, a nonparametric statistical test, namely the Mann Whitney U test was conducted to determine possible differences. An analysis of the data showed that 21 respondents had entrepreneurship as their dominant career orientation while 12 fell in the technical/functional, 12 in the challenging, 9 in the service and 8 in the autonomy

Structural models of the membrane anchors of envelope glycoproteins E1 and E2 from pestiviruses

Science.gov (United States)

Wang, Jimin; Li, Yue; Modis, Yorgo

2014-01-01

The membrane anchors of viral envelope proteins play essential roles in cell entry. Recent crystal structures of the ectodomain of envelope protein E2 from a pestivirus suggest that E2 belongs to a novel structural class of membrane fusion machinery. Based on geometric constraints from the E2 structures, we generated atomic models of the E1 and E2 membrane anchors using computational approaches. The E1 anchor contains two amphipathic perimembrane helices and one transmembrane helix; the E2 anchor contains a short helical hairpin stabilized in the membrane by an arginine residue, similar to flaviviruses. A pair of histidine residues in the E2 ectodomain may participate in pH sensing. The proposed atomic models point to Cys987 in E2 as the site of disulfide bond linkage with E1 to form E1–E2 heterodimers. The membrane anchor models provide structural constraints for the disulfide bonding pattern and overall backbone conformation of the E1 ectodomain. PMID:24725935

ANTS-anchored Zn-Al-CO3-LDH particles as fluorescent probe for sensing of folic acid

International Nuclear Information System (INIS)

Liu, Pengfei; Liu, Dan; Liu, Yanhuan; Li, Lei

2016-01-01

A novel fluorescent nanosensor for detecting folic acid (FA) in aqueous media has been developed based on 8-aminonaphthalene-1,3,6-trisulfonate (ANTS) anchored to the surface of Zn-Al-CO 3 -layered double hydroxides (LDH) particles. The nanosensor showed high fluorescence intensity and good photostability due to a strong coordination interaction between surface Zn 2+ ions of Zn-Al-CO 3 -LDH and N atoms of ANTS, which were verified by result of X-ray photoelectron spectroscopy (XPS). ANTS-anchored on the surface of Zn-Al-CO 3 -LDH restricted the intra-molecular rotation leading to ANTS-anchored J-type aggregation emission enhancement. ANTS-anchored Zn-Al-CO 3 -LDH particles exhibited highly sensitive and selective response to FA over other common metal ions and saccharides present in biological fluids. The proposed mechanism was that oxygen atoms of -SO 3 groups in ANTS-anchored on the surface of Zn-Al-CO 3 -LDH were easily collided by FA molecules to form potential hydrogen bonds between ANTS-anchored and FA molecules, which could effectively quench the ANTS-anchored fluorescence. Under the simulated physiological conditions (pH of 7.4), the fluorescence quenching was fitted to Stern-Volmer equation with a linear response in the concentration range of 1 μM to 200 μM with a limit of detection of 0.1 μM. The results indicate that ANTS-anchored Zn-Al-CO 3 -LDH particles can afford a very sensitive system for the sensing FA in aqueous solution. - Highlights: • A novel fluorescent nanosensor has been developed. • The sensor exhibited highly sensitive and selective response to FA. • The fluorescence quenching was fitted to Stern–Volmer equation. • The linear response range was 1–200 μM with a limit of detection of 0.1 μM.

Employees’ work engagement and job commitment: The moderating role of career anchors

Directory of Open Access Journals (Sweden)

Melinde Coetzee

2014-08-01

Research purpose: The objective of the present study was to assess whether individuals’career anchors (measured by the career orientations inventory significantly moderate therelationship between their work engagement (measured by the Utrecht work engagementscale and job commitment (measured by the organisation-related commitment scale. Motivation for the study: Although the literature review suggests that people’s workengagement and job commitment may be influenced by their career anchors, there seems to bea paucity of research examining the interaction effects between these three variables. Research approach, design and method: A cross-sectional quantitative survey approach wasused. A non-probability purposive sample of adults (N = 318 employed in a human resourcecapacity in the South African service industry participated in the study. Stepwise hierarchicalmoderated regression analysis was performed to achieve the objective of the study. Main findings: The results showed that the work engagement-job commitment relationshipwas generally stronger for high career anchor preferences than for low career anchorpreferences.Practical/managerial implications: The results of the study can be useful when human resourceinterventions for enhancing employees’ engagement and commitment are developed. Contribution: The results of the study add new insights to the career literature by showing thatpeople’s career self-concepts (as reflected by their career anchors are important to consider inenhancing their work engagement and job commitment.

High Performance Flexible Pseudocapacitor based on Nano-architectured Spinel Nickel Cobaltite Anchored Multiwall Carbon Nanotubes

International Nuclear Information System (INIS)

Shakir, Imran

2014-01-01

Highlights: • Two-step fabrication method for nano-architectured spinel nickel cobaltite (NiCo 2 O 4 ) anchored MWCNTs composite. • High performance flexible energy-storage devices. • The NiCo 2 O 4 anchored MWCNTs Exhibits 2032 Fg −1 capacitance which is 1.62 times greater than pristine NiCo 2 O 4 at 1 Ag −1 . - Abstract: We demonstrate a facile two-step fabrication method for nano-architectured spinel nickel cobaltite (NiCo 2 O 4 ) anchored multiwall carbon nanotubes (MWCNTs) based electrodes for high performance flexible energy-storage devices. As electrode materials for flexible supercapacitors, the NiCo 2 O 4 anchored MWCNTs exhibits a high specific capacitance of 2032 Fg −1 , which is nearly 1.62 times greater than pristine NiCo 2 O 4 nanoflakes at 1 Ag −1 . The synthesized NiCo 2 O 4 anchored MWCNTs composite shows excellent rate performance (83.96% capacity retention at 30 Ag −1 ) and stability with coulombic efficiency over 96% after 5,000 cycles when being fully charged/discharged at 1 Ag −1 . Furthermore, NiCo 2 O 4 anchored MWCNTs achieve a maximum energy density of 48.32 Whkg −1 at a power density of 480 Wkg −1 which is 60% higher than pristine NiCo 2 O 4 electrode and significantly outperformed electrode materials based on NiCo 2 O 4 which are currently used in the state-of-the-art supercapacitors throughout the literature. This superior rate performance and high-capacity value offered by NiCo 2 O 4 anchored MWCNTs is mainly due to enhanced electronic and ionic conductivity, which provides a short diffusion path for ions and an easy access of electrolyte flow to nickel cobaltite redox centers besides the high conductivity of MWCNTs

Use of an all-suture anchor for re-creation of the anterior talofibular ligament: a case report.

Science.gov (United States)

Piraino, Jason A; Busch, Elliot L; Sansosti, Laura E; Pettineo, Steven J; Creech, Corine

2015-01-01

The lateral ankle ligament complex is typically injured during athletic activity caused by an inversion force on a plantar flexed foot. Numerous open surgical procedures to reconstruct the lateral ankle complex have been described. In contrast, we present a case report in which an all-suture anchor was used arthroscopically to re-create the anterior talofibular ligament in conjunction with ankle arthroscopy. A retrospective analysis of a 55-year-old male with a work-related inversion ankle sprain was performed with 14 months of follow-up. Objective and subjective assessments were obtained using range of motion measures, a strength assessment, and the Foot Function Index. An all-suture anchor was deployed through the anterolateral portal and secured in both the fibula and talus, re-creating the anterior talofibular ligament at its origin and insertion. Active range of motion physical therapy began at 2 weeks postoperatively. The patient started a neuromuscular re-education program at 5 weeks with minimal pain or discomfort. A return to full duty was achieved at 3 months postoperatively. To our knowledge, the use of an all-suture anchor has not been previously reported for lateral ankle complex re-creation. It is hoped that this approach to anterior talofibular ligament repair will decrease the incidence of complications and improve outcomes. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

A legged anchoring mechanism for capsule endoscopes using micropatterned adhesives.

Science.gov (United States)

Glass, Paul; Cheung, Eugene; Sitti, Metin

2008-12-01

This paper presents a new concept for an anchoring mechanism to enhance existing capsule endoscopes. The mechanism consists of three actuated legs with compliant feet lined with micropillar adhesives to be pressed into the intestine wall to anchor the device at a fixed location. These adhesive systems are inspired by gecko and beetle foot hairs. Single-leg and full capsule mathematical models of the forces generated by the legs are analyzed to understand capsule performance. Empirical friction models for the interaction of the adhesives with an intestinal substrate were experimentally determined in vitro using dry and oil-coated elastomer micropillar arrays with 140 microm pillar diameter, 105 microm spacing between pillars, and an aspect ratio of 1:1 on fresh porcine small intestine specimens. Capsule prototypes were also tested in a simulated intestine environment and compared with predicted peristaltic loads to assess the viability of the proposed design. The experimental results showed that a deployed 10 gr capsule robot can withstand axial peristaltic loads and anchor reliably when actuation forces are greater than 0.27 N using dry micropillars. Required actuation forces may be reduced significantly by using micropillars coated with a thin silicone oil layer.

Double-Row Suture Anchor Repair of Posterolateral Corner Avulsion Fractures.

Science.gov (United States)

Gilmer, Brian B

2017-08-01

Posterolateral corner avulsion fractures are a rare variant of ligamentous knee injury primarily described in the skeletally immature population. Injury is often related to a direct varus moment placed on the knee during sporting activities. Various treatment strategies have been discussed ranging from nonoperative management, to excision of the bony fragment, to primary repair with screws or suture. The described technique is a means for achieving fixation of the bony avulsion using principles familiar to double-row transosseous equivalent rotator cuff repair. Proximal anchors are placed in the epiphysis, and sutures are passed in horizontal mattress fashion. Once tied, the limbs of these same sutures are then passed to more distal anchors. Remaining eyelet sutures can be used to manage peripheral tissue. The final repair provides anatomic reduction and compression of the fragment to its bony bed with minimal extracortical hardware prominence and no violation of the physis. Risks include potential for physeal injury or chondral damage to the lateral femoral condyle through aberrant anchor placement. Postoperative care includes toe-touch weight-bearing restrictions and range of motion restrictions of 0°-90° in a hinged brace for 6 weeks followed by gradual return to activity.

A Single-hole stone anchor from Kottapatnam: Early historic port site of Andhra Pradesh, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Rao, K.P.; Kumari, S.; Imsong, O.; Vanlalhruaitluangi, V.

of Kottapatnam and this is the first stone anchor reported from Andhra coast. In this paper the single hole stone anchor has been detailed along with its probable period and the trade contacts of Kottapatnam as a port...

Study of intrinsic anchoring in nematic liquid crystals based on modified Gruhn-Hess pair potential

International Nuclear Information System (INIS)

Zhang Zhidong; Zhang Yanjun

2008-01-01

A nematic liquid crystal slab composed of N molecular layers is investigated using a simple cubic lattice model, based upon the molecular pair potential which is spatially anisotropic and dependent on elastic constants of liquid crystals. A perfect nematic order is assumed in the theoretical treatment, which means the orientation of the molecular long axis coincides with the director of liquid crystal and the total free energy equals to the total interaction energy. We present a modified Gruhn-Hess model, which is relative to the splay-bend elastic constant K 13 . Furthermore, we have studied the free nematic interfacial behavior (intrinsic anchoring) by this model in the assumption of the perfect nematic order. We find that the preferred orientation at the free interface and the intrinsic anchoring strength change with the value of modification, and that the director profile can be determined by the competition of the intrinsic anchoring with external forces present in the system. Also we simulate the intrinsic anchoring at different temperatures using Monte Carlo method and the simulation results show that the intrinsic anchoring favors planar alignment and the free interface is more disordered than the bulk

The utilisation of a career conversation framework based on Schein’s career anchors model

Directory of Open Access Journals (Sweden)

Magda Bezuidenhout

2013-07-01

Full Text Available Orientation: This  study  constituted  and  reported  on  the  outcomes  of  a  structured  career conversation  framework  based  on  Schein’s  eight  career  anchors  in  an  open  distance  and e-learning (ODeL university in South Africa. Research purpose: The purpose of the research was to report on the utilisation of a structured career conversation framework based on Schein’s career anchors model. Motivation for the study: The rationale for the study was the paucity of studies investigating career anchors in South Africa’s multicultural organisational context. Research design, approach and method: A quantitative approach was adopted in the study. The population consisted of 4200 employees at a university in South Africa. Statistical analysis was performed using one-way analysis of variance (ANOVA as well as a Scheffe post hoc test. Main  findings: The  findings  of  this  study  suggest  that  career  conversation  has  a  dynamic nature (i.e. it changes over a period of time. Consequently, career development interventions in the workplace need to approach the workforce holistically. Practical/managerial implications: The findings and results will assist managers, practitioners and  career  development  specialists  in  the  practical  implementation  of  the  career  anchor concept. Contribution/value-add: The career conversation framework based on Schein’s career anchors has expanded the existing theory to find the right balance between career conversations and career anchors to keep people motivated to perform optimally in an organisation.

Bone-anchored titanium implants for auricular rehabilitation: case report and review of literature

Directory of Open Access Journals (Sweden)

Emne Hammoud Gumieiro

Full Text Available CONTEXT AND OBJECTIVE: Osseointegrated implants have acquired an important role in the prosthetic rehabilitation of patients with craniofacial defects. The main indications are lack of local tissue for autogenous reconstruction, previous reconstruction failure and selection of this technique by the patient. This paper presents a clinical case and discusses indications and advantages of the osseointegrated implant technique for retention of auricular prostheses. TYPE OF STUDY: Case report, Universidade Federal de São Paulo (UNIFESP. METHODS: A female patient received three auricular implants after surgical resection of a hemangioma in her left ear. The time taken for osseointegration of the temporal bone was three months. After fabrication of the implant-retained auricular prosthesis, the patient was monitored for 12 months. RESULTS: The clinical parameters evaluated showed good postoperative healing, healthy peri-implant tissue, good hygiene and no loss of implants. Good hygiene combined with thin and immobile peri-implant soft tissues resulted in minimal complications. Craniofacial implant integration appears to be site-dependent; increasing age affects osseointegration in the temporal bone. The frequency of adverse skin reactions in peri-implant tissues is generally low. CONCLUSION: The surgical technique for rehabilitation using implant-retained auricular prostheses seems to be simple. It is associated with low rates of adverse skin reactions and long-term complications. Prostheses anchored by osseointegrated implants seem to provide better retention than do prostheses supported on spectacle frames, less risk of discoloration through the use of adhesives and better esthetic results than do prostheses anchored in the surgical cavity

MAIL1 is essential for development of the primary root but not of anchor roots.

Science.gov (United States)

Ühlken, Christine; Hoth, Stefan; Weingartner, Magdalena

2014-01-01

MAIN-LIKE1 (MAIL1) is a ubiquitously expressed nuclear protein, which has a crucial function during root development. We have recently described loss of function mutants for MAIL1, in which the organization and function of the primary root meristem is lost soon after germination. Moreover cell differentiation is impaired resulting in primary root growth arrest soon after emergence. Here we show that mail1 mutants form several anchor roots from the hypocotyl to root junction. These anchor roots show similar defects in the organization of the stem cell niche as the primary root. In contrast, differentiation processes are not impaired and thus anchor roots seem to be able to compensate for the loss of primary root function. Our data show that MAIL1 is essential for specification of cell fate in the primary root but not in anchor roots.

Influence of weak anchoring upon the alignment of smectic A liquid crystals with surface pretilt

International Nuclear Information System (INIS)

De Vita, R; Stewart, I W

2008-01-01

Equilibrium configurations for smectic A liquid crystals in a 'bookshelf' geometry are determined from a nonlinear continuum model under strong and weak anchoring conditions at the boundary for the usual director n. Natural boundary conditions are derived for n and the smectic layer normal a when a preferred director orientation n p , which generally induces a director pretilt, is prescribed on the boundaries. Two key aspects are examined via the nonlinear equilibrium equations: the separation of n from a and the influence of weak anchoring. The orientations of n and a relative to n p may differ significantly and depend very much upon the magnitude of the anchoring strength. These results from a nonlinear theory are natural and novel developments of previous classical linearized models for which n ≡ a. Comparisons are also drawn between solutions for strong and weak anchoring conditions

A three-dimensional rupture analysis of steel liners anchored to concrete pressure and containment vessels

International Nuclear Information System (INIS)

Bangash, Y.

1987-01-01

Steel liners or plates are anchored to concrete pressure and containment vessels for nuclear and offshore facilities. Due to extreme loading conditions a liner may buckle due to the pull-out or shearing of anchors from the base metal and concrete. Under certain conditions attributed to loadings, liner metal deterioration and cracking of concrete behind the liner, the liner may fail by rupture. This paper presents a three-dimensional analysis of steel-concrete elements, using finite elements analysis in which a provision is made for liner instability, anchor strength and stiffness, concrete cracking and finally liner rupture. The analysis is tested first on an octagonal slab with and without an anchored steel liner. It is then extended to concrete pressure and containment vessels. The analytical results obtained are compared well with those available from the experimental tests and other sources. (author)

Biomechanical evaluation of straight antegrade nailing in proximal humeral fractures: the rationale of the "proximal anchoring point".

Science.gov (United States)

Euler, Simon A; Petri, Maximilian; Venderley, Melanie B; Dornan, Grant J; Schmoelz, Werner; Turnbull, Travis Lee; Plecko, Michael; Kralinger, Franz S; Millett, Peter J

2017-09-01

Varus failure is one of the most common failure modes following surgical treatment of proximal humeral fractures. Straight antegrade nails (SAN) theoretically provide increased stability by anchoring to the densest zone of the proximal humerus (subchondral zone) with the end of the nail. The aim of this study was to biomechanically investigate the characteristics of this "proximal anchoring point" (PAP). We hypothesized that the PAP would improve stability compared to the same construct without the PAP. Straight antegrade humeral nailing was performed in 20 matched pairs of human cadaveric humeri for a simulated unstable two-part fracture. Biomechanical testing, with stepwise increasing cyclic axial loading (50-N increments each 100 cycles) at an angle of 20° abduction revealed significantly higher median loads to failure for SAN constructs with the PAP (median, 450 N; range, 200-1.000 N) compared to those without the PAP (median, 325 N; range, 100-500 N; p = 0.009). SAN constructs with press-fit proximal extensions (endcaps) showed similar median loads to failure (median, 400 N; range, 200-650 N), when compared to the undersized, commercially available SAN endcaps (median, 450 N; range, 200-600 N; p = 0.240). The PAP provided significantly increased stability in SAN constructs compared to the same setup without this additional proximal anchoring point. Varus-displacing forces to the humeral head were superiorly reduced in this setting. This study provides biomechanical evidence for the "proximal anchoring point's" rationale. Straight antegrade humeral nailing may be beneficial for patients undergoing surgical treatment for unstable proximal humeral fractures to decrease secondary varus displacement and thus potentially reduce revision rates.

Lower limit of strength wedge-type anchor bolts

International Nuclear Information System (INIS)

Arnedo Pena, A.; Frances Urmeneta, M.

1998-01-01

Simple expansion bolts, with a split expansion ring and a threaded bolt with an integral cone expander, called wedge type, are very used in securing and anchoring structures. The anchorage is obtained by a mechanism of torque-controlled expansion. Although less resistant than other types, its easy installation and low cost make them very competitive in light structures. In this paper, the minimum capacity values are analysed, when they are used to anchor safety-related equipment in NPP. The EPRI criteria developed in response to USI A-46 are applied and complemented by the new CEB Anchorage Design Guide. The results are compared with the information from european manufactures, adopting different safety factors for cracked and non-cracked concrete. With adequate control and inspection measures, including areas of noticeable cracking of concrete. minimum values for equipment can be obtained satisfying the strictest seismic validation requirements. (Author) 5 refs

Optimization Analysis Model of Self-Anchored Suspension Bridge

Directory of Open Access Journals (Sweden)

Pengzhen Lu

2014-01-01

Full Text Available The hangers of self-anchored suspension bridge need to be tensioned suitably during construction. In view of this point, a simplified optimization calculation method of cable force for self-anchored suspension bridge has been developed based on optimization theories, such as minimum bending energy method, and internal force balanced method, influence matrix method. Meanwhile, combined with the weak coherence of main cable and the adjacently interaction of hanger forces, a simplified analysis method is developed using MATLAB, which is then compared with the optimization method that consider the main cable's geometric nonlinearity with software ANSYS in an actual example bridge calculation. This contrast proves the weak coherence of main cable displacement and the limitation of the adjacent cable force influence. Furthermore, a tension program that is of great reference value has been developed; some important conclusions, advices, and attention points have been summarized.

Design method of redundancy of brace-anchor sharing supporting based on cooperative deformation

Science.gov (United States)

Liu, Jun-yan; Li, Bing; Liu, Yan; Cai, Shan-bing

2017-11-01

Because of the complicated environment requirement, the support form of foundation pit is diversified, and the brace-anchor sharing support is widely used. However, the research on the force deformation characteristics and the related aspects of the cooperative response of the brace-anchor sharing support is insufficient. The application of redundancy theory in structural engineering has been more mature, but there is little theoretical research on redundancy theory in underground engineering. Based on the idea of collaborative deformation, the paper calculates the ratio of the redundancy degree of the cooperative deformation by using the local reinforcement design method and the structural component redundancy parameter calculation formula based on Frangopol. Combined with the engineering case, through the calculation of the ratio of cooperative deformation redundancy in the joint of brace-anchor sharing support. This paper explores the optimal anchor distribution form under the condition of cooperative deformation, and through the analysis and research of displacement field and stress field, the results of the collaborative deformation are validated by comparing the field monitoring data. It provides theoretical basis for the design of this kind of foundation pit in the future.

Method and apparatus for dismantling mechanical anchors

Energy Technology Data Exchange (ETDEWEB)

Dubovskiy, Yu P; Chendev, F S; Gritsayuk, B I; Gubin, N I; Osipov, S P

1982-01-01

This apparatus is designed to reduce the amount of labor required to dismantle mechanical anchors while at the same time lowering expenditures for lumber. Longwall beams and timber skips are used to support the cap and any fractured rock faces. The apparatus itself has grooves, vertical guides, and a drive system to position the longwall beams.

A Proteomics Investigation of Anchored PKA-RI Signaling

NARCIS (Netherlands)

Kovanich, D.

2013-01-01

Compartmentalization of kinases and phosphatases plays an important role in the specificity of second messenger mediated signaling events. Localization of the cAMP-dependent protein kinase is mediated by interaction of its regulatory subunit (PKA-R) with the versatile family of A-kinase anchoring

Study on monitoring of deep foundation pit with SMW engineering method plus anchor cable retaining structure

Science.gov (United States)

Chen, Wenzhao; Cui, Wenping

2018-03-01

The SMW method has many advantages, such as little influence on the surrounding environment, good watertight performance, wide range of application, short construction period, low cost and so on. In this paper, we chose the SMW engineering method combined with anchor cable to support structure in the second phase deep foundation pit of Jinan LuJinDongCheng as the research object, monitored and analysed the horizontal displacement of the pile top, Peripheral surface subsidence and internal force of the anchor cable in the foundation pit. We also discussed the displacement, internal force of anchor cable and the settlement of surrounding environment in the excavation of foundation pit and in different stages of construction. Conclusion:(1)The maximum horizontal displacement of the retaining structure is closely related to the depth and time of excavation, the construction of anchor cable can well limit the deformation of pile body; (2)Groundwater seepage caused by foundation pit dewatering will change the effective stress of soil. The change of groundwater level has an important influence on the working behavior of smw anchor cable supporting structure.

Influence of weak anchoring upon the alignment of smectic A liquid crystals with surface pretilt

Energy Technology Data Exchange (ETDEWEB)

De Vita, R [Department of Engineering Science and Mechanics, Virginia Tech, 230 Norris Hall, Blacksburg, VA 24061 (United States); Stewart, I W [Department of Mathematics, University of Strathclyde, Livingstone Tower, 26 Richmond Street, Glasgow G1 1XH (United Kingdom)], E-mail: devita@vt.edu, E-mail: i.w.stewart@strath.ac.uk

2008-08-20

Equilibrium configurations for smectic A liquid crystals in a 'bookshelf' geometry are determined from a nonlinear continuum model under strong and weak anchoring conditions at the boundary for the usual director n. Natural boundary conditions are derived for n and the smectic layer normal a when a preferred director orientation n{sub p}, which generally induces a director pretilt, is prescribed on the boundaries. Two key aspects are examined via the nonlinear equilibrium equations: the separation of n from a and the influence of weak anchoring. The orientations of n and a relative to n{sub p} may differ significantly and depend very much upon the magnitude of the anchoring strength. These results from a nonlinear theory are natural and novel developments of previous classical linearized models for which n {identical_to} a. Comparisons are also drawn between solutions for strong and weak anchoring conditions.

Triple-Loaded Suture Anchors Versus a Knotless Rip Stop Construct in a Single-Row Rotator Cuff Repair Model.

Science.gov (United States)

Noyes, Matthew P; Lederman, Evan; Adams, Christopher R; Denard, Patrick J

2018-05-01

To compare the biomechanical properties of single-row repair with triple-loaded (TL) anchor repair versus a knotless rip stop (KRS) repair in a rotator cuff repair model. Rotator cuff tears were created in 8 cadaveric matched-pair specimens and repaired with a TL anchor or KRS construct. In the TL construct, anchors were placed in the greater tuberosity and then all suture limbs were passed through the rotator cuff as simple sutures and tied. In the KRS construct, a 2-mm suture tape was passed through the tendon in an inverted mattress fashion, and a free suture was passed medial to the suture tape to create a rip-stop. Then, the suture tape and free suture were secured with knotless anchors. Displacement was observed with video tracking after cyclic loading, and specimens were loaded to failure. The mean load to failure was 438 ± 59 N in TL anchor repairs compared with 457 ± 110 N in KRS repairs (P = .582). The mean displacement with cyclic loading was 3.8 ± 1.6 mm in TL anchor repairs versus 4.3 ± 1.8 mm in the KRS group (P = .297). Mode of failure was consistent in both groups, with 6 of 8 failures in the TL anchor group and 7 of 8 failures in KRS group occurring from anchor pullout. There is no statistical difference in load to failure and cyclic loading between TL anchor and KRS single-row repair techniques. KRS repair technique may be an alternative method of repairing full-thickness supraspinatus tendon tears with a single-row construct. Copyright © 2018 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Binding constants of membrane-anchored receptors and ligands: A general theory corroborated by Monte Carlo simulations.

Science.gov (United States)

Xu, Guang-Kui; Hu, Jinglei; Lipowsky, Reinhard; Weikl, Thomas R

2015-12-28

Adhesion processes of biological membranes that enclose cells and cellular organelles are essential for immune responses, tissue formation, and signaling. These processes depend sensitively on the binding constant K2D of the membrane-anchored receptor and ligand proteins that mediate adhesion, which is difficult to measure in the "two-dimensional" (2D) membrane environment of the proteins. An important problem therefore is to relate K2D to the binding constant K3D of soluble variants of the receptors and ligands that lack the membrane anchors and are free to diffuse in three dimensions (3D). In this article, we present a general theory for the binding constants K2D and K3D of rather stiff proteins whose main degrees of freedom are translation and rotation, along membranes and around anchor points "in 2D," or unconstrained "in 3D." The theory generalizes previous results by describing how K2D depends both on the average separation and thermal nanoscale roughness of the apposing membranes, and on the length and anchoring flexibility of the receptors and ligands. Our theoretical results for the ratio K2D/K3D of the binding constants agree with detailed results from Monte Carlo simulations without any data fitting, which indicates that the theory captures the essential features of the "dimensionality reduction" due to membrane anchoring. In our Monte Carlo simulations, we consider a novel coarse-grained model of biomembrane adhesion in which the membranes are represented as discretized elastic surfaces, and the receptors and ligands as anchored molecules that diffuse continuously along the membranes and rotate at their anchor points.

Organization, 'Anchoring' of Knowledge, and Innovative Activity in Construction

DEFF Research Database (Denmark)

Drejer, Ina; Vinding, Anker Lund

2006-01-01

The construction industry is characterised by the widespread use of project organisation. It has been suggested that the relatively low level of innovative activity in the industry can be explained by the temporary nature of firm boundary-crossing projects. Survey data from the Danish construction...... industry is used to investigate the importance of learning and 'anchoring' of project-specific knowledge at the firm level for participation in innovative activities. The data cover both the overall Danish construction industry and a specific region, North Jutland, which has a relatively high...... specialisation of construction workers. Latent class and regression analyses reveal that firms that make extensive use of partnering, together with internal product and process evaluation and knowledge diffusion (labelled 'knowledge-anchoring mechanisms'), are more likely to participate in innovative activities...

Others' opinions count, but not all of them: anchoring to ingroup versus outgroup members' behavior in charitable giving

Directory of Open Access Journals (Sweden)

Dorina Hysenbelli

2013-11-01

Full Text Available Because of the large amount of information and the difficulty in selecting an appropriate recipient in the context of charitable giving, people tend to make extensive use of heuristics, which sometimes leads them to wrong decisions. In the present work, we focused on exploring how individuals are influenced by anchoring heuristics and how group membership interacts with this heuristic. In Experiment 1, two different groups of participants were informed about low versus high average donations of other people, and a third control group did not receive any information about the others' donations. The results showed that participants were willing to donate significantly more in the high-anchor condition compared to the low-anchor condition, as well as about the same amount of money in the low-anchor condition and no-anchor condition. Experiment 2 and 3 showed that high anchors are more effective when the information about others' donations reflects members of the ingroup rather than the outgroup. Other variables related to these results are further discussed.

Nanofabricated racks of aligned and anchored DNA substrates for single-molecule imaging.

Science.gov (United States)

Gorman, Jason; Fazio, Teresa; Wang, Feng; Wind, Shalom; Greene, Eric C

2010-01-19

Single-molecule studies of biological macromolecules can benefit from new experimental platforms that facilitate experimental design and data acquisition. Here we develop new strategies to construct curtains of DNA in which the molecules are aligned with respect to one another and maintained in an extended configuration by anchoring both ends of the DNA to the surface of a microfluidic sample chamber that is otherwise coated with an inert lipid bilayer. This "double-tethered" DNA substrate configuration is established through the use of nanofabricated rack patterns comprised of two distinct functional elements: linear barriers to lipid diffusion that align DNA molecules anchored by one end to the bilayer and antibody-coated pentagons that provide immobile anchor points for the opposite ends of the DNA. These devices enable the alignment and anchoring of thousands of individual DNA molecules, which can then be visualized using total internal reflection fluorescence microscopy under conditions that do not require continuous application of buffer flow to stretch the DNA. This unique strategy offers the potential for studying protein-DNA interactions on large DNA substrates without compromising measurements through application of hydrodynamic force. We provide a proof-of-principle demonstration that double-tethered DNA curtains made with nanofabricated rack patterns can be used in a one-dimensional diffusion assay that monitors the motion of quantum dot-tagged proteins along DNA.

Operative treatment of acromioclavicular joint dislocation: a new technique with suture anchors

Directory of Open Access Journals (Sweden)

Zhang Jingwei

2014-07-01

Full Text Available 【Abstract】Objective: To evaluate clinical outcome of suture anchors in strengthening both acromioclavicular and coracoclavicular ligaments in the surgical treatment of acromioclavicular joint dislocation. Methods: Twenty-eight patients with acute traumatic Rockwood III, IV and V dislocations of the acromioclavicular joint surgically treated at our institute between October 2010 and January 2012 were recruited. All patients underwent open reduction combined with suture anchors. Function was evaluated using the ConstantMurley shoulder score. Clinical and radiographic shoulder ratings were evaluated using Taft criteria at 3, 6 and 12 months. Results:Two cases with fixation loosening were not included in final statistical analysis. Other patients obtained full joint reposition on immediate postoperative radiographs. Follow-up was performed with an average of 15.6 months (range, 12-19. After early range of motion exercises, 96.2% of the patients (25/26 could abduct and elevate their shoulders more than 90 degrees within postoperative 3 months. There was no infection. Average Constant-Murley score was 96.3 points (range, 94-100 and mean Taft shoulder rating was 10.7 points (range, 8-12 at 12 months. Conclusion: The suture anchor is a relatively simple technique and can avoid screw removal which is helpful in reconstructing both acromioclavicular and coracoclavicular ligaments in acute traumatic acromioclavicular joint dislocation. Key words: Acromioclavicular joint; Dislocations; Surgery; Suture anchors

Innovation in abutment-free bone-anchored hearing devices in children: Updated results and experience.

Science.gov (United States)

Baker, Shaun; Centric, Aaron; Chennupati, Sri Kiran

2015-10-01

Bone-anchored hearing devices are an accepted treatment option for hearing restoration in various types of hearing loss. Traditional devices have a percutaneous abutment for attachment of the sound processor that contributes to a high complication rate. Previously, our institution reported on the Sophono (Boulder, CO, USA) abutment-free system that produced similar audiologic results to devices with abutments. Recently, Cochlear Americas (Centennial, CO, USA) released an abutment-free bone-anchored hearing device, the BAHA Attract. In contrast to the Sophono implant, the BAHA Attract utilizes an osseointegrated implant. This study aims to demonstrate patient benefit abutment-free devices, compare the results of the two abutment-free devices, and examine complication rates. A retrospective chart review was conducted for the first eleven Sophono implanted patients and for the first six patients implanted with the BAHA Attract at our institution. Subsequently, we analyzed patient demographics, audiometric data, clinical course and outcomes. Average improvement for the BAHA Attract in pure-tone average (PTA) and speech reception threshold (SRT) was 41dB hearing level (dBHL) and 56dBHL, respectively. Considering all frequencies, the BAHA Attract mean improvement was 39dBHL (range 32-45dBHL). The Sophono average improvement in PTA and SRT was 38dBHL and 39dBHL, respectively. The mean improvement with Sophono for all frequencies was 34dBHL (range 24-43dBHL). Significant improvements in both pure-tone averages and speech reception threshold for both devices were achieved. In direct comparison of the two separate devices using the chi-square test, the PTA and SRT data between the two devices do not show a statistically significant difference (p-value 0.68 and 0.56, respectively). The complication rate for these abutment-free devices is lower than that of those featuring the transcutaneous abutment, although more studies are needed to further assess this potential advantage

ANTS-anchored Zn-Al-CO{sub 3}-LDH particles as fluorescent probe for sensing of folic acid

Energy Technology Data Exchange (ETDEWEB)

Liu, Pengfei; Liu, Dan; Liu, Yanhuan [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Key Laboratory of Environmentally Harmful Chemical Analysis, Beijing University of Chemical Technology, Beijing 100029 (China); Li, Lei, E-mail: lilei@mail.buct.edu.cn [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Beijing Key Laboratory of Environmentally Harmful Chemical Analysis, Beijing University of Chemical Technology, Beijing 100029 (China)

2016-09-15

A novel fluorescent nanosensor for detecting folic acid (FA) in aqueous media has been developed based on 8-aminonaphthalene-1,3,6-trisulfonate (ANTS) anchored to the surface of Zn-Al-CO{sub 3}-layered double hydroxides (LDH) particles. The nanosensor showed high fluorescence intensity and good photostability due to a strong coordination interaction between surface Zn{sup 2+} ions of Zn-Al-CO{sub 3}-LDH and N atoms of ANTS, which were verified by result of X-ray photoelectron spectroscopy (XPS). ANTS-anchored on the surface of Zn-Al-CO{sub 3}-LDH restricted the intra-molecular rotation leading to ANTS-anchored J-type aggregation emission enhancement. ANTS-anchored Zn-Al-CO{sub 3}-LDH particles exhibited highly sensitive and selective response to FA over other common metal ions and saccharides present in biological fluids. The proposed mechanism was that oxygen atoms of -SO{sub 3} groups in ANTS-anchored on the surface of Zn-Al-CO{sub 3}-LDH were easily collided by FA molecules to form potential hydrogen bonds between ANTS-anchored and FA molecules, which could effectively quench the ANTS-anchored fluorescence. Under the simulated physiological conditions (pH of 7.4), the fluorescence quenching was fitted to Stern-Volmer equation with a linear response in the concentration range of 1 μM to 200 μM with a limit of detection of 0.1 μM. The results indicate that ANTS-anchored Zn-Al-CO{sub 3}-LDH particles can afford a very sensitive system for the sensing FA in aqueous solution. - Highlights: • A novel fluorescent nanosensor has been developed. • The sensor exhibited highly sensitive and selective response to FA. • The fluorescence quenching was fitted to Stern–Volmer equation. • The linear response range was 1–200 μM with a limit of detection of 0.1 μM.

Anatomic suture anchor versus the Broström technique for anterior talofibular ligament repair: a biomechanical comparison.

Science.gov (United States)

Waldrop, Norman E; Wijdicks, Coen A; Jansson, Kyle S; LaPrade, Robert F; Clanton, Thomas O

2012-11-01

Despite the popularity of the Broström procedure for secondary repair of chronic lateral ankle instability, there have been no biomechanical studies reporting on the strength of this secondary repair method, whether using suture fixation or suture anchors. The purpose of our study was to perform a biomechanical comparison of the ultimate load to failure and stiffness of the traditional Broström technique using only a suture repair compared with a suture anchor repair of the anterior talofibular ligament (ATFL) at time zero. We believed that fixation strength of the suture anchor repair would be closer to the strength of the native ligament and allow more aggressive rehabilitation. Controlled laboratory study. Twenty-four fresh-frozen cadaveric ankles were randomly divided into 4 groups of 6 specimens. One group was an intact control group, and the other groups consisted of the traditional Broström and 2 suture anchor modifications (suture anchors in talus or fibula) of the Broström procedure. The specimens were loaded to failure to determine the strength and stiffness of each construct. In load-to-failure testing, ultimate failure loads of the Broström (68.2 ± 27.8 N; P = .013), suture anchor fibula (79.2 ± 34.3 N; P = .037), and suture anchor talus (75.3 ± 45.6 N; P = .027) repairs were significantly lower than that of the intact (160.9 ± 72.2 N) ATFL group. Stiffness of the Broström (6.0 ± 2.5 N/mm; P = .02), suture anchor fibula (6.8 N/mm ± 2.7; P = .05), and suture anchor talus (6.6 N/mm ± 4.0; P = .04) repairs were significantly lower than that of the intact (12.4 N/mm ± 4.1 N/mm) ATFL group. The 3 repair groups were not significantly different from each other, but all 3 were substantially lower in strength and stiffness when compared to the intact ATFL. The use of suture anchors to repair the ATFL produces a repair that can withstand loads to failure similar to the suture-only Broström repair. However, all 3 repair groups were much weaker than

Dynamic behaviour of anchors in cracked and uncracked concrete: a progress report

International Nuclear Information System (INIS)

Rodriguez, M.; Klingner, R.E.

1997-01-01

In early 1993, the US Nuclear Regulatory Commission began a research program at The University of Texas at Austin, dealing with the dynamic behavior of anchors in cracked and uncracked concrete. In this paper, the progress of that research program is reviewed. The test program is summarized, and work performed to date is reviewed, with emphasis on the dynamic and static behavior of single tensile anchors in uncracked concrete. General conclusions from that work are discussed, and future plans are presented. (orig.)

Stable Pt clusters anchored to monovacancies on graphene sheets

Energy Technology Data Exchange (ETDEWEB)

Medasani, Bharat K.; Liu, Jun; Sushko, Maria L.

2017-10-09

anchor'>

Phosphatidylkojibiosyl Diglyceride: metabolism and function as an anchor in bacterial cell membrane.

Science.gov (United States)

Pieringer, R A

1975-07-01

The recently discovered phosphoglycolipid, phosphatidylkojibiosyl diglyceride (PKD), was first observed as a biosynthetic by-product of glycosyl diglyceride metabolism in Streptococcus faecalis (faecium) ATCC 9790. Its structure is 1, 2-diacyl-3-O-alpha-Dglucopyranosyl-6'-O-phosphoryl- [1'', 2''-diacyl-3''-O-sn-glycerol]-alpha-D-glucopyranosyl)-sn-glycerol. The biosynthesis of phosphatidyl-kojibiosyl diglyceride occurs by a novel transphosphatidylation reaction in which a phosphatidyl glycerol to the primary alcohol function at the 6 position of the internal glucose of kojibiosyl diglyceride. The reaction is catalyzed by a membrane-derived enzyme. Phosphatidyl-kojibiosyl diglyceride is bound covalently through a phosphodiester bond to the polyglycerol phosphate moiety of membrane lipoteichoic acid from S. faecalis. Phosphatidylkojibiosyl diglyceride has four nonpolar long chain fatty acyl groups and appears to have the necessary physico-chemical properties to anchor the long hydrophilic glycerol phosphate polymer of lipoteichoic acid to the hydrophobic enviroment of the membrane of S. faecalis and probably other gram-positive bacteria as well.

Culturally-Anchored Values and University Education Experience Perception

Science.gov (United States)

Mitsis, Ann; Foley, Patrick

2009-01-01

Purpose: The purpose of this paper is to examine whether business students' gender, age and culturally-anchored values affect their perceptions of their university course experience. Design/methodology/approach: Culturally diverse business students (n 1/4 548) studying at an Australian university were surveyed using previously established scales.…

Mining Tasks from the Web Anchor Text Graph: MSR Notebook Paper for the TREC 2015 Tasks Track

Science.gov (United States)

2015-11-20

Mining Tasks from the Web Anchor Text Graph: MSR Notebook Paper for the TREC 2015 Tasks Track Paul N. Bennett Microsoft Research Redmond, USA pauben...anchor text graph has proven useful in the general realm of query reformulation [2], we sought to quantify the value of extracting key phrases from...anchor text in the broader setting of the task understanding track. Given a query, our approach considers a simple method for identifying a relevant

Consistency Anchor Formalization and Correctness Proofs

OpenAIRE

Miguel, Correia; Bessani, Alysson

2014-01-01

This is report contains the formal proofs for the techniques for increasing the consistency of cloud storage as presented in "Bessani et al. SCFS: A Cloud-backed File System. Proc. of the 2014 USENIX Annual Technical Conference. June 2014." The consistency anchor technique allows one to increase the consistency provided by eventually consistent cloud storage services like Amazon S3. This technique has been used in the SCFS (Shared Cloud File System) cloud-backed file system for solving rea...

Inelastic seismic behavior of post-installed anchors for nuclear safety related structures: Generation of experimental database

Energy Technology Data Exchange (ETDEWEB)

Mahadik, Vinay, E-mail: vinay.mahadik@iwb.uni-stuttgart.de; Sharma, Akanshu; Hofmann, Jan

2016-02-15

Highlights: • Experiments for evaluating seismic behavior of anchors were performed. • Two undercut anchor products in use in nuclear facilities were considered. • Monotonic tension, shear and cycling tension tests at different crack widths. • Crack cycling tests at constant, in-phase and out-of phase tension loads. • Characteristics for the two anchors as a function of crack width were identified. - Abstract: Post installed (PI) anchors are often employed for connections between concrete structure and components or systems in nuclear power plants (NPP) and related facilities. Standardized practices for nuclear related structures demand stringent criteria, which an anchor has to satisfy in order to qualify for use in NPP related structures. In NPP and related facilities, the structure–component interaction in the event of an earthquake depends on the inelastic behavior of the concrete structure, the component system and also the anchorage system that connects them. For analysis, anchorages are usually assumed to be rigid. Under seismic actions, however, it is known that anchors may undergo significant plastic displacement and strength degradation. Analysis of structure–component interaction under seismic loads calls for numerical models simulating inelastic behavior of anchorage systems. A testing program covering different seismic loading scenarios in a reasonably conservative manner is required to establish a basis for generating numerical models of anchorage systems. Currently there is a general lack of modeling techniques to consider the inelastic behavior of anchorages in structure–component interaction under seismic loads. In this work, in view of establishing a basis for development of numerical models simulating the inelastic behavior of anchors, seismic tests on two different undercut anchors qualified for their use in NPP related structures were carried out. The test program was primarily based on the DIBt-KKW-Leitfaden (2010) guidelines

Appearance traits in fish farming: progress from classical genetics to genomics, providing insight into current and potential genetic improvement

Directory of Open Access Journals (Sweden)

Nelson eColihueque

2014-08-01

Full Text Available Appearance traits in fish, those external body characteristics that influence consumer acceptance at point of sale, have come to the forefront of commercial fish farming, as culture profitability is closely linked to management of these traits. Appearance traits comprise mainly body shape and skin pigmentation. Analysis of the genetic basis of these traits in different fish reveals significant genetic variation within populations, indicating potential for their genetic improvement. Work into ascertaining the minor or major genes underlying appearance traits for commercial fish is emerging, with substantial progress in model fish in terms of identifying genes that control body shape and skin colors. In this review, we describe research progress to date, especially with regard to commercial fish, and discuss genomic findings in model fish in order to better address the genetic basis of the traits. Given that appearance traits are important in commercial fish, the genomic information related to this issue promises to accelerate the selection process in coming years.

Appearance traits in fish farming: progress from classical genetics to genomics, providing insight into current and potential genetic improvement

Science.gov (United States)

Colihueque, Nelson; Araneda, Cristian

2014-01-01

Appearance traits in fish, those external body characteristics that influence consumer acceptance at point of sale, have come to the forefront of commercial fish farming, as culture profitability is closely linked to management of these traits. Appearance traits comprise mainly body shape and skin pigmentation. Analysis of the genetic basis of these traits in different fish reveals significant genetic variation within populations, indicating potential for their genetic improvement. Work into ascertaining the minor or major genes underlying appearance traits for commercial fish is emerging, with substantial progress in model fish in terms of identifying genes that control body shape and skin colors. In this review, we describe research progress to date, especially with regard to commercial fish, and discuss genomic findings in model fish in order to better address the genetic basis of the traits. Given that appearance traits are important in commercial fish, the genomic information related to this issue promises to accelerate the selection process in coming years. PMID:25140172

Setting sail for glucose homeostasis with the AKAP150-PP2B-anchor.

Science.gov (United States)

Teo, Adrian Kee Keong; Kulkarni, Rohit N

2012-10-17

Glucose-stimulated insulin secretion, controlled by multiple protein phosphorylation events, is critical for the regulation of glucose homeostasis. Protein kinase A (PKA) is known to play a role in β cell physiology, but the role of its anchoring protein is not fully understood. Hinke et al (2012) illustrate the significance of A-kinase anchoring protein 150 in tethering protein phosphatase 2B to mediate nutrient-stimulated insulin secretion and thus modulate glucose homeostasis.

The relation between career anchors, occupational types and job satisfaction of midcareer employees

OpenAIRE

J. A. Ellison; A. M. G. Schreuder

2000-01-01

The objective of this research was to determine the value of the career anchor model in career decision-making. Career models that can provide the individual with greater self-insight can serve as an important guide when making career choices in todays turbulent working environment. Two hundred and ninety-five midcareer employees (managerial and non-managerial) completed questionnaires to determine their career anchor, occupation type and levels of general, intrinsic and extrinsic job satisfa...

Analysis of timber and coating material on an iron anchor recovered off Aguada Bay, Goa

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Rao, B.R.; Shashikala, S.; Rao, R.V.; Khedekar, V.D.

Shanked iron anchor measuring 3.30 m long with a 4.37 m wooden stock was recovered off Aguada Bay, Goa at a water depth of 11 m. The anchor has been tentatively dated contemporary with the maritime history of Goa and Portugal between the 16th and 17th...

The Architecture of School Improvement

Science.gov (United States)

Murphy, Joseph

2013-01-01

Purpose: The aim of this paper is to present a comprehensive framework for capturing the complex concept the authors call school improvement. Design/methodology/approach: The author begins by anchoring that framework on an historical understanding of school improvement. The framework itself is then presented. Five dimensions are described: the…

Modeling and experimental validation of sawing based lander anchoring and sampling methods for asteroid exploration

Science.gov (United States)

Zhang, Jun; Dong, Chengcheng; Zhang, Hui; Li, Song; Song, Aiguo

2018-05-01

This paper presents a novel lander anchoring system based on sawing method for asteroid exploration. The system is composed of three robotic arms, three cutting discs, and a control system. The discs mounted at the end of the arms are able to penetrate into the rock surface of asteroids. After the discs cut into the rock surface, the self-locking function of the arms provides forces to fix the lander on the surface. Modeling, trajectory planning, simulations, mechanism design, and prototype fabrication of the anchoring system are discussed, respectively. The performances of the system are tested on different kinds of rocks, at different sawing angles, locations, and speeds. Results show that the system can cut 15 mm deep into granite rock in 180 s at sawing angle of 60°, with the average power of 58.41 W, and the "weight on bit" (WOB) of 8.637 N. The 7.8 kg anchoring system is capable of providing omni-directional anchoring forces, at least 225 N normal and 157 N tangent to the surface of the rock. The system has the advantages of low-weight, low energy consumption and balance forces, high anchoring efficiency and reliability, and could enable the lander to move and sample or assist astronauts and robots in walking and sampling on asteroids.

Induction of bone ingrowth with a micropore bioabsorbable suture anchor in rotator cuff tear: an experimental study in a rabbit model.

Science.gov (United States)

Kang, Yun Gyeong; Kim, Jung-Han; Shin, Jung-Woog; Baik, Jong-Min; Choo, Hye-Jung

2013-11-01

The bioabsorbable suture anchor is probably one of the most commonly used tools in arthroscopic shoulder operations. However, there is controversy about whether the bioabsorbable anchor is replaced by bone. The object of this study is to evaluate bone ingrowth into the micropore bioabsorbable suture anchor and the differences in the biomechanical properties of a micropore anchor and a nonpore anchor. A total of 16 microsized holes (diameter, 250 ± 50 μm; depth, 0.2 mm) were made on the bioabsorbable anchors with a microdrill. Twelve adult New Zealand White rabbits were randomly divided into two groups: group A (n = 6), the nonpore bioabsorbable suture anchor group, and group pA (n = 6), the micropore bioabsorbable suture anchor group. Microcomputed tomography was used at 4 and 8 weeks postoperatively to evaluate ingrowth by bone volume fraction (BVF), which was measured by calculating the ratio of the total volume of bone ingrowth to that of the region of interest. For pullout strength testing, 3 additional rabbits (6 limbs) were used for mechanical testing. The mean BVF was higher in group pA (0.288 ± 0.054) than in group A (0.097 ± 0.006). The micropore anchor had a higher pullout strength (0.520 ± 0.294 N) than the nonpore anchor (0.275 ± 0.064 N). Micropore bioabsorbable suture anchors induced bone ingrowth and showed higher pullout strength, despite processing. Copyright © 2013 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Mosby, Inc. All rights reserved.

The double-anchoring theory of lightness perception: a comment on Bressan (2006).

Science.gov (United States)

Howe, Piers D L; Sagreiya, Hersh; Curtis, Dwight L; Zheng, Chengjie; Livingstone, Margaret S

2007-10-01

Recently, a double-anchoring theory (DAT) of lightness perception was proposed (P. Bressan, 2006), which offers explanations for all the data explained by the original anchoring theory (A. Gilchrist et al., 1999), as well as a number of additional lightness phenomena. Consequently, DAT can account for an unprecedented range of empirical results, potentially explaining everything from the basic simultaneous contrast display to subtle variations of the Gelb effect. In this comment, the authors raised 4 concerns that demonstrate serious theoretical and empirical difficulties for DAT. PsycINFO Database Record (c) 2007 APA, all rights reserved.

Exploring body-anchored and experience-based learning in a community of practice

DEFF Research Database (Denmark)

Stelter, Reinhard

2008-01-01

which, in a second step, is presented as part of the social realm and as one of the prerequisites of learning in a community of practice. This integration is established and becomes visible through the following two concepts: 1. Reification as the outflow of co-ordinated action, and 2. narratives......The article aims to integrate body-anchored and experience-based learning in the theoretical concept of learning in a community of practice. Present moment, epoché, intentional orientation and meaning making are introduced as the four basic premises for body-anchored and experience-based learning...

Spectroscopic and first principles investigation on 4-[(4-pyridinylmethylene)amino]-benzoic acid bearing pyridyl and carboxyl anchoring groups

Science.gov (United States)

Zhang, Lei; Wang, Qiaoyi

2018-03-01

We report a combined experimental and computational investigation on the structure and photophysics of 4-[(4-pyridinylmethylene)amino]-benzoic acid, a functional molecule bearing two anchoring groups for attachment onto a TiO2 surface and perovskite surface, for potential solar cell application. This molecule possesses interesting adsorption properties in perovskite solar cell because the pyridyl group serves as the Lewis base and targets Lewis acidic sites in the perovskite surface, while the carboxyl group targets TiO2 surface, improving the coupling between the perovskite surface and the TiO2 surface. The electronic structures of the molecule and its photochemistry are revealed by the UV-vis absorption spectra and the fluorescence spectra under visible light irradiation, which are combined with density functional theory (DFT) and time-dependent density functional theory (TDDFT) analysis. Considering the bi-anchoring groups and the conjugated π system embedded in the molecule, we anticipate it can molecular engineer the TiO2/perovskite interface in perovskite solar cell.

Decay accelerating factor (DAF) is anchored to membranes by a C-terminal glycolipid

International Nuclear Information System (INIS)

Medof, M.E.; Haas, R.; Walter, E.I.; Rosenberry, T.L.

1986-01-01

Purified 70 kDa membrane (m) DAF incorporates into cells when added in vitro. A 2 kDa smaller DAF form which functions extrinsically like C4bp but is unable to incorporate can be isolated from urine (u). Because of common deficits of mDAF and acetylcholinesterase (AChE) in erythrocytes (E) of patients with paroxysmal nocturnal hemoglobinuria (PNH), mDAF was analyzed for a O-terminal glycolipid membrane anchor similar to that in E AChE. Incubation of E with phosphatidylinositol-specific phospholipase C, an enzyme which cleaves a similar glycolipid anchor in trypanosome variant surface glycoproteins (mfVSGs), released 20% of the DAF antigen. The released DAF species resembled uDAF in size, extrinsic model of C4b2a decay, and lack of hydrophobicity. Reductive radiomethylation of mDAF with [ 14 C]HCHO and NaCNBH 3 revealed ethanolamine and glucosamine in proportions similar to those in the E AChE glycolipid anchor. Papain cleavage of radiomethylated mDAF released the labeled ethanolamine and glucosamine in small O-terminal fragments from the residual DAF that retained N-terminal Asp. Following labeling of the anchors of mDAF and E AChE with the lipophilic photoreagent 3-trifluoromethyl-3-(m-[ 125 I]iodophenyl)diazirine, cleavage at the glucosamine residue by deamination quantitatively released the label from both proteins. Biosynthetic labeling of Hela cells with [ 3 H]ethanolamine resulted in rapid 3 H incorporation into both 48 kDa proDAF and 70 kDa mDAF. These data indicate that mDAF is anchored by a glycolipid similar to that in E AChE, mfVSGs and Thy-1 antigen and raise the possibility that a defect in the assembly or attachment of this structure could account for the deficits of mDAF and E AChE in PNH

Root hairs aid soil penetration by anchoring the root surface to pore walls.

Science.gov (United States)

Bengough, A Glyn; Loades, Kenneth; McKenzie, Blair M

2016-02-01

The physical role of root hairs in anchoring the root tip during soil penetration was examined. Experiments using a hairless maize mutant (Zea mays: rth3-3) and its wild-type counterpart measured the anchorage force between the primary root of maize and the soil to determine whether root hairs enabled seedling roots in artificial biopores to penetrate sandy loam soil (dry bulk density 1.0-1.5g cm(-3)). Time-lapse imaging was used to analyse root and seedling displacements in soil adjacent to a transparent Perspex interface. Peak anchorage forces were up to five times greater (2.5N cf. 0.5N) for wild-type roots than for hairless mutants in 1.2g cm(-3) soil. Root hair anchorage enabled better soil penetration for 1.0 or 1.2g cm(-3) soil, but there was no significant advantage of root hairs in the densest soil (1.5g cm(-3)). The anchorage force was insufficient to allow root penetration of the denser soil, probably because of less root hair penetration into pore walls and, consequently, poorer adhesion between the root hairs and the pore walls. Hairless seedlings took 33h to anchor themselves compared with 16h for wild-type roots in 1.2g cm(-3) soil. Caryopses were often pushed several millimetres out of the soil before the roots became anchored and hairless roots often never became anchored securely.The physical role of root hairs in anchoring the root tip may be important in loose seed beds above more compact soil layers and may also assist root tips to emerge from biopores and penetrate the bulk soil. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

A general pipeline for the development of anchor markers for comparative genomics in plants

Directory of Open Access Journals (Sweden)

Stougaard Jens

2006-08-01

Full Text Available Abstract Background Complete or near-complete genomic sequence information is presently only available for a few plant species representing a large phylogenetic diversity among plants. In order to effectively transfer this information to species lacking sequence information, comparative genomic tools need to be developed. Molecular markers permitting cross-species mapping along co-linear genomic regions are central to comparative genomics. These "anchor" markers, defining unique loci in genetic linkage maps of multiple species, are gene-based and possess a number of features that make them relatively sparse. To identify potential anchor marker sequences more efficiently, we have established an automated bioinformatic pipeline that combines multi-species Expressed Sequence Tags (EST and genome sequence data. Results Taking advantage of sequence data from related species, the pipeline identifies evolutionarily conserved sequences that are likely to define unique orthologous loci in most species of the same phylogenetic clade. The key features are the identification of evolutionarily conserved sequences followed by automated design of intron-flanking Polymerase Chain Reaction (PCR primer pairs. Polymorphisms can subsequently be identified by size- or sequence variation of PCR products, amplified from mapping parents or populations. We illustrate our procedure in legumes and grasses and exemplify its application in legumes, where model plant studies and the genome- and EST-sequence data available have a potential impact on the breeding of crop species and on our understanding of the evolution of this large and diverse family. Conclusion We provide a database of 459 candidate anchor loci which have the potential to serve as map anchors in more than 18,000 legume species, a number of which are of agricultural importance. For grasses, the database contains 1335 candidate anchor loci. Based on this database, we have evaluated 76 candidate anchor loci

A new technique of "midline anchoring" in spinal cord stimulation dramatically reduces lead migration.

Science.gov (United States)

Mironer, Y Eugene; Brown, Christopher; Satterthwaite, John R; Cohen, Mary; Tonder, Lisa M; Grumman, Steve

2004-01-01

Spinal cord stimulation (SCS) is a popular method of treatment of chronic pain. Unfortunately, migration of the lead continues to be a serious complication of this therapy. In an attempt to reduce lateral migration of the SCS lead, we performed a retrospective assessment of a new technique of percutaneous lead placement. This new method of "midline anchoring" of the lead using the plica mediana dorsalis was tested against conventional technique in a retrospective study involving 122 trials and 91 implants of SCS over a period of five years. The use of "midline anchoring" resulted in a decrease in lead migration from 23% to 6% after trial insertion and from 24% to 7% after implantation. We conclude that "midline anchoring" of the SCS lead is an effective method of preventing lead migration.

Tritium labelling of a cholesterol amphiphile designed for cell membrane anchoring of proteins.

Science.gov (United States)

Schäfer, Balázs; Orbán, Erika; Kele, Zoltán; Tömböly, Csaba

2015-01-01

Cell membrane association of proteins can be achieved by the addition of lipid moieties to the polypeptide chain, and such lipid-modified proteins have important biological functions. A class of cell surface proteins contains a complex glycosylphosphatidylinositol (GPI) glycolipid at the C-terminus, and they are accumulated in cholesterol-rich membrane microdomains, that is, lipid rafts. Semisynthetic lipoproteins prepared from recombinant proteins and designed lipids are valuable probes and model systems of the membrane-associated proteins. Because GPI-anchored proteins can be reinserted into the cell membrane with the retention of the biological function, they are appropriate candidates for preparing models via reduction of the structural complexity. A synthetic headgroup was added to the 3β-hydroxyl group of cholesterol, an essential lipid component of rafts, and the resulting cholesterol derivative was used as a simplified GPI mimetic. In order to quantitate the membrane integrated GPI mimetic after the exogenous addition to live cells, a tritium labelled cholesterol anchor was prepared. The radioactive label was introduced into the headgroup, and the radiolabelled GPI mimetic anchor was obtained with a specific activity of 1.37 TBq/mmol. The headgroup labelled cholesterol derivative was applied to demonstrate the sensitive detection of the cell membrane association of the anchor under in vivo conditions. Copyright © 2015 John Wiley & Sons, Ltd.

Electrical properties and mechanical stability of anchoring groups for single-molecule electronics

Directory of Open Access Journals (Sweden)

Riccardo Frisenda

2015-07-01

Full Text Available We report on an experimental investigation of transport through single molecules, trapped between two gold nano-electrodes fabricated with the mechanically controlled break junction (MCBJ technique. The four molecules studied share the same core structure, namely oligo(phenylene ethynylene (OPE3, while having different aurophilic anchoring groups: thiol (SAc, methyl sulfide (SMe, pyridyl (Py and amine (NH2. The focus of this paper is on the combined characterization of the electrical and mechanical properties determined by the anchoring groups. From conductance histograms we find that thiol anchored molecules provide the highest conductance; a single-level model fit to current–voltage characteristics suggests that SAc groups exhibit a higher electronic coupling to the electrodes, together with better level alignment than the other three groups. An analysis of the mechanical stability, recording the lifetime in a self-breaking method, shows that Py and SAc yield the most stable junctions while SMe form short-lived junctions. Density functional theory combined with non-equlibrium Green’s function calculations help in elucidating the experimental findings.

Anchored PKA as a gatekeeper for gap junctions.

Science.gov (United States)

Pidoux, Guillaume; Taskén, Kjetil

2015-01-01

Anchored protein kinase A (PKA) bound to A Kinase Anchoring Protein (AKAP) mediates effects of localized increases in cAMP in defined subcellular microdomains and retains the specificity in cAMP-PKA signaling to distinct extracellular stimuli. Gap junctions are pores between adjacent cells constituted by connexin proteins that provide means of communication and transfer of small molecules. While the PKA signaling is known to promote human trophoblast cell fusion, the gap junction communication through connexin 43 (Cx43) is a prerequisite for this process. We recently demonstrated that trophoblast fusion is regulated by ezrin, a known AKAP, which binds to Cx43 and delivers PKA in the vicinity gap junctions. We found that disruption of the ezrin-Cx43 interaction abolished PKA-dependent phosphorylation of Cx43 as well as gap junction communication and subsequently cell fusion. We propose that the PKA-ezrin-Cx43 macromolecular complex regulating gap junction communication constitutes a general mechanism to control opening of Cx43 gap junctions by phosphorylation in response to cAMP signaling in various cell types.

Analytical and experimental evaluation of the capacity of the bottom rail in partially anchored timber shear walls

OpenAIRE

Caprolu, Giuseppe; Källsner, Bo; Girhammar, Ulf Arne; Vessby, Johan

2012-01-01

Källsner and Girhammar have developed plastic design methods for light-frame timber shear walls that can be used for determining the load-carrying capacity when the shear walls are partially anchored. For such walls, the leading stud is not fully anchored against uplift and tying down forces are developed in the sheathing-to-framing joints. Since the forces in the anchor bolts and the sheathing-to-framing joints do not act in the same vertical plane, the bottom rail will be subjected to cross...

Correlation of Persistence, Initiative and Career Anchors Categories of Students

Directory of Open Access Journals (Sweden)

I A Novikova

2008-03-01

Full Text Available The article is devoted to the analysis of the results of comparative empirical study of persistence, initiative and Career Anchors categories of the students on the basis of the systemic-functional approach.

Interaction of Rupture Zones of Adjacent Anchor Plates in an Analogical Medium

Directory of Open Access Journals (Sweden)

H. Abbad

2013-12-01

Full Text Available In this paper, an experimental study which required the design and implementation of a model containing plastic granules powder to simulate a natural environment, is presented. The latter is subjected to the removal of "anchor plates." For each test, several digital photographs are taken to materialize different deformed configurations during the pullout process. These photos processed in couples by the 7D software (image correlation giving the evolution of the displacement field and plane strain analogical environment. Particular attention is paid to the discussion of the interference of rupture zones of neighboring anchors by reducing the axis between plates.

Interpreting the Third International Mathematics and Science Study (TIMSS) achievement scales using scale anchoring

Science.gov (United States)

Kelly, Dana L.

1999-11-01

The scale anchoring method was used to analyze and describe the TIMSS primary and middle school (Populations 1 and 2) mathematics and science achievement scales. Scale anchoring is a way of attaching meaning to a scale by describing what students know and can do at specific points on the scale. Student achievement was scrutinized at four points on the TIMSS primary and middle school achievement scales---the 25th, 50th, 75th, and 90th international percentiles for fourth and eighth grades. The scale anchoring method was adapted for the TIMSS data and items that students scoring at each of the four scale points were likely to answer correctly (with a 65 percent probability) were identified. The items were assembled in binders organized by anchor level and content area. Two ten-member panels of subject-matter specialists were convened to scrutinize the items, draft descriptions of student proficiency at the four scale points, and identify example TIMSS items to illustrate performance at each level. Following the panel meetings, the descriptions were refined through an iterative review process. The result is a content-referenced interpretation of the TIMSS scales through which TIMSS achievement results can be better communicated and understood.

Adaptive Anchoring Model: How Static and Dynamic Presentations of Time Series Influence Judgments and Predictions.

Science.gov (United States)

Kusev, Petko; van Schaik, Paul; Tsaneva-Atanasova, Krasimira; Juliusson, Asgeir; Chater, Nick

2018-01-01

When attempting to predict future events, people commonly rely on historical data. One psychological characteristic of judgmental forecasting of time series, established by research, is that when people make forecasts from series, they tend to underestimate future values for upward trends and overestimate them for downward ones, so-called trend-damping (modeled by anchoring on, and insufficient adjustment from, the average of recent time series values). Events in a time series can be experienced sequentially (dynamic mode), or they can also be retrospectively viewed simultaneously (static mode), not experienced individually in real time. In one experiment, we studied the influence of presentation mode (dynamic and static) on two sorts of judgment: (a) predictions of the next event (forecast) and (b) estimation of the average value of all the events in the presented series (average estimation). Participants' responses in dynamic mode were anchored on more recent events than in static mode for all types of judgment but with different consequences; hence, dynamic presentation improved prediction accuracy, but not estimation. These results are not anticipated by existing theoretical accounts; we develop and present an agent-based model-the adaptive anchoring model (ADAM)-to account for the difference between processing sequences of dynamically and statically presented stimuli (visually presented data). ADAM captures how variation in presentation mode produces variation in responses (and the accuracy of these responses) in both forecasting and judgment tasks. ADAM's model predictions for the forecasting and judgment tasks fit better with the response data than a linear-regression time series model. Moreover, ADAM outperformed autoregressive-integrated-moving-average (ARIMA) and exponential-smoothing models, while neither of these models accounts for people's responses on the average estimation task. Copyright © 2017 The Authors. Cognitive Science published by Wiley

Density control of dodecamanganese clusters anchored on silicon(100).

Science.gov (United States)

Condorelli, Guglielmo G; Motta, Alessandro; Favazza, Maria; Nativo, Paola; Fragalà, Ignazio L; Gatteschi, Dante

2006-04-24

A synthetic strategy to control the density of Mn12 clusters anchored on silicon(100) was investigated. Diluted monolayers suitable for Mn12 anchoring were prepared by Si-grafting mixtures of the methyl 10-undecylenoate precursor ligand with 1-decene spectator spacers. Different ratios of these mixtures were tested. The grafted surfaces were hydrolyzed to reveal the carboxylic groups available for the subsequent exchange with the [Mn12O12(OAc)16(H2O)4]4 H2O2 AcOH cluster. Modified surfaces were analyzed by attenuated total reflection (ATR)-FTIR spectroscopy, X-ray photoemission spectroscopy (XPS), and AFM imaging. Results of XPS and ATR-FTIR spectroscopy show that the surface mole ratio between grafted ester and decene is higher than in the source solution. The surface density of the Mn12 cluster is, in turn, strictly proportional to the ester mole fraction. Well-resolved and isolated clusters were observed by AFM, using a diluted ester/decene 1:1 solution.

AKAP18:PKA-RIIα structure reveals crucial anchor points for recognition of regulatory subunits of PKA.

Science.gov (United States)

Götz, Frank; Roske, Yvette; Schulz, Maike Svenja; Autenrieth, Karolin; Bertinetti, Daniela; Faelber, Katja; Zühlke, Kerstin; Kreuchwig, Annika; Kennedy, Eileen J; Krause, Gerd; Daumke, Oliver; Herberg, Friedrich W; Heinemann, Udo; Klussmann, Enno

2016-07-01

A-kinase anchoring proteins (AKAPs) interact with the dimerization/docking (D/D) domains of regulatory subunits of the ubiquitous protein kinase A (PKA). AKAPs tether PKA to defined cellular compartments establishing distinct pools to increase the specificity of PKA signalling. Here, we elucidated the structure of an extended PKA-binding domain of AKAP18β bound to the D/D domain of the regulatory RIIα subunits of PKA. We identified three hydrophilic anchor points in AKAP18β outside the core PKA-binding domain, which mediate contacts with the D/D domain. Such anchor points are conserved within AKAPs that bind regulatory RII subunits of PKA. We derived a different set of anchor points in AKAPs binding regulatory RI subunits of PKA. In vitro and cell-based experiments confirm the relevance of these sites for the interaction of RII subunits with AKAP18 and of RI subunits with the RI-specific smAKAP. Thus we report a novel mechanism governing interactions of AKAPs with PKA. The sequence specificity of each AKAP around the anchor points and the requirement of these points for the tight binding of PKA allow the development of selective inhibitors to unequivocally ascribe cellular functions to the AKAP18-PKA and other AKAP-PKA interactions. © 2016 The Author(s). published by Portland Press Limited on behalf of the Biochemical Society.

Relation between anchorings of liquid crystals and conformation changes in aligning agents by the Langmuir-Blodgett film technique investigation

International Nuclear Information System (INIS)

Zhu, Y.; Lu, Z.; Wei, Y.

1995-01-01

The anchoring direction of liquid crystals on a solid substrate surface depends upon many parameters characterizing the liquid-crystal--substrate interface, a variation of which may change this anchoring direction leading to the so-called anchoring transition. Here, based on the Langmuir-Blodgett film technique, we present two model systems to study the relation between anchoring directions and the conformation changes in aligning agents. A double-armed crown ether liquid crystal and a side chain polymer liquid crystal at an air-water interface both show phase transitions, accompanied by conformation changes. However, when the monolayers in different phases were transferred onto solid substrates to orient liquid crystals, we found that for the crown ether material the conformation change can alter the anchoring of liquid crystals between homeotropic and homogeneous alignments, while for the polymer liquid crystal, despite the conformation changes, the liquid crystals can only be aligned homeotropically. The involved mechanisms were briefly discussed in terms of the Landau-type phenomenological theory

Stone anchors along the coast of Chilika Lake: New light on the maritime activities of Orissa, India

Digital Repository Service at National Institute of Oceanography (India)

Tripati, S.; Patnaik, A.P.

the growth of maritime trade. With increase in the carrying capacity of ships, changes made in their sizes and construction patterns, subsequently, the size and shape of the anchors also got modified. On the basis of anchor findings, an attempt has been made...

Surgical repair of central slip avulsion injuries with Mitek bone anchor--retrospective analysis of a case series.

LENUS (Irish Health Repository)

Chan, Jeffrey C Y

2007-01-01

The purpose of this study is to describe our technique of central slip repair using the Mitek bone anchor and to evaluate the treatment outcome. Eight digits in eight patients were reconstructed using the bone anchor: three little fingers, two middle fingers, two index fingers and one ring finger. There were two immediate and six delayed repairs (range from one day to eight months). Four patients had pre-operative intensive splinting and physiotherapy to restore passive extension of the proximal interphalangeal joint prior to central slip reconstruction. All patients have made good progress since surgery. No patient requires a second procedure and none of the bone anchors have dislodged or loosened. We conclude that the Mitek bone anchor is a reliable technique to achieve soft tissue to bone fixation in central slip avulsion injuries. We recommend that this technique be considered as a treatment option for patients requiring surgical repair.

Understanding and valuing environmental issues: the effects of availability and anchoring on judgment.

Science.gov (United States)

van der Pligt, J; van Schie, E C; Hoevenagel, R

1998-01-01

This paper addresses the effects of availability and anchoring-and-adjustment on people's beliefs and values concerning environmental issues. The first three studies focus on lay people's perceptions of the causes of large scale environmental risks, the second series of three studies deals with how people value environmental goods and how much they are prepared to pay to mitigate environmental risks. In studies 1-3 we investigate the effects of availability and anchoring-and-adjustment on estimating the contribution of various factors to large scale environmental risks. Highly complex risks such as acid rain and global warming tend to be associated with multiple causes, and our results show that estimating the role of these causes is clearly affected by availability and anchoring-and-adjustment. Both have sizeable effects and persist over time. Moreover, corrective procedures only seem to have a limited effect. Availability and anchoring-and-adjustment not only play a role in judging the possible causes of risks; they also play a role in research attempting to assess the public's willingness to pay (WTP) to protect our environment. The outcomes of WTP surveys are often used as a tool to help policy decision making. In the second part of this article we present three studies on this issue. Results provide further evidence of the impact of the two heuristics on the outcomes of WTP research. Implications for research and practice are briefly discussed.

Phospholipase D specific for the phosphatidylinositol anchor of cell-surface proteins is abundant in plasma

International Nuclear Information System (INIS)

Low, M.G.; Prasad, A.R.S.

1988-01-01

An enzyme activity capable of degrading the glycosyl-phosphatidylinositol membrane anchor of cell-surface proteins has previously been reported in a number of mammalian tissues. The experiments reported here demonstrate that this anchor-degrading activity is also abundant in mammalian plasma. The activity was inhibited by EGTA or 1,10-phenanthroline. It was capable of removing the anchor from alkaline phosphatase, 5'-nucleotidase, and variant surface glycoprotein but had little or no activity toward phosphatidylinositol or phosphatidylcholine. Phosphatidic acid was the only 3 H-labeled product when this enzyme hydrolyzed [ 3 H]myristate-labeled variant surface glycoprotein. It could be distinguished from the Ca 2 =-dependent inositol phospholipid-specific phospholipase C activity in several rat tissues on the basis of its molecular size and its sensitivity to 1,10-phenanthroline. The data therefore suggest that this activity is due to a phospholipase D with specificity for glycosylphosphatidylinositol structures. Although the precise physiological function of this anchor-specific phospholipase D remains to be determined, these findings indicate that it could play an important role in regulating the expression and release of cell-surface proteins in vivo

Technical Note: Drifting vs. anchored flux chambers for measuring greenhouse gas emissions from running waters

Science.gov (United States)

Lorke, A.; Bodmer, P.; Noss, C.; Alshboul, Z.; Koschorreck, M.; Somlai, C.; Bastviken, D.; Flury, S.; McGinnis, D. F.; Maeck, A.; Müller, D.; Premke, K.

2015-09-01

Stream networks were recently discovered as major but poorly constrained natural greenhouse gas (GHG) sources. A fundamental problem is that several measurement approaches have been used without cross comparisons. Flux chambers represent a potentially powerful methodological approach if robust and reliable ways to use chambers on running water can be defined. Here we compare the use of anchored and freely drifting chambers on various streams having different flow velocities. The study clearly shows that (1) drifting chambers have a very small impact on the water turbulence under the chamber and thus generate more reliable fluxes, (2) anchored chambers enhance turbulence under the chambers and thus elevate fluxes, (3) the bias of the anchored chambers greatly depends on chamber design and sampling conditions, and (4) there is a promising method to reduce the bias from anchored chambers by using a flexible plastic foil seal to the water surface rather than having rigid chamber walls penetrating into the water. Altogether, these results provide novel guidance on how to apply flux chambers in running water, which will have important consequences for measurements to constrain the global GHG balances.

Technical note: drifting versus anchored flux chambers for measuring greenhouse gas emissions from running waters

Science.gov (United States)

Lorke, A.; Bodmer, P.; Noss, C.; Alshboul, Z.; Koschorreck, M.; Somlai-Haase, C.; Bastviken, D.; Flury, S.; McGinnis, D. F.; Maeck, A.; Müller, D.; Premke, K.

2015-12-01

Stream networks have recently been discovered to be major but poorly constrained natural greenhouse gas (GHG) sources. A fundamental problem is that several measurement approaches have been used without cross-comparisons. Flux chambers represent a potentially powerful methodological approach if robust and reliable ways to use chambers on running water can be defined. Here we compare the use of anchored and freely drifting chambers on various streams with different flow velocities. The study clearly shows that (1) anchored chambers enhance turbulence under the chambers and thus elevate fluxes, (2) drifting chambers have a very small impact on the water turbulence under the chamber and thus generate more reliable fluxes, (3) the bias of the anchored chambers greatly depends on chamber design and sampling conditions, and (4) there is a promising method to reduce the bias from anchored chambers by using a flexible plastic foil collar to seal the chambers to the water surface, rather than having rigid chamber walls penetrating into the water. Altogether, these results provide novel guidance on how to apply flux chambers in running water, which will have important consequences for measurements to constrain the global GHG balances.

High-throughput physical map anchoring via BAC-pool sequencing

Czech Academy of Sciences Publication Activity Database

Cviková, Kateřina; Cattonaro, F.; Alaux, M.; Stein, N.; Mayer, K.F.X.; Doležel, Jaroslav; Bartoš, Jan

2015-01-01

Roč. 15, APR 11 (2015) ISSN 1471-2229 R&D Projects: GA ČR GA13-08786S; GA MŠk(CZ) LO1204 Institutional support: RVO:61389030 Keywords : Physical map * Contig anchoring * Next generation sequencing Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.631, year: 2015

Approaches to enhance body-anchored and experience-based learning

DEFF Research Database (Denmark)

Stelter, Reinhard

2008-01-01

in the rhythm and intentional orientation can also be applied to different areas, for example, psychotherapy or coaching. But the main focus is on examples from physical education. The final part of the article sees body-anchored learning as integrated in a cultural setting and as part of learning...

Mandatory appearances of forensic examiner for cross-examination in court and related systemic improvement under china's criminal procedure

Directory of Open Access Journals (Sweden)

Jianye Qu

2017-01-01

Full Text Available In China's criminal procedure system, forensic advice is one of the key types of evidence. These advices play an important part in discovering the facts of a case, convictions, and sentencing, and they cannot be ignored in assessments of guilt and the death penalty. However, due to broad and flexible criminal laws, in actual litigation, the nonappearance of forensic examiner or mere provision of documentation of advice read in court has become the norm. This has led to the existence in name only of cross-examination rights, which directly damages the legitimate rights and interests of the parties and the objective and impartial rulings of referees. At present, there is no legal clarity in criminal proceedings that examiner should or should not be examined in court. In my opinion, the entire court system should require an appearance in court, which must be a clear mandatory appearance with specific exceptions. The system should guarantee the forensic examiner' mandatory appearances, which would inevitably improve the rules of evidence.

Retractable Robotic Anchor for Hard Rock and Granular Soils, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — ProtoInnovations proposes to research, develop, and validate an innovative retractable robotic anchoring mechanism that works both in hard rock and granular soils...

Percutaneous Transcholecystic Biliary Interventions Using Gallbladder Anchors: Feasibility Study in the Swine

International Nuclear Information System (INIS)

Lopera, Jorge E.; Kirsch, David; Qian Zhong; Ruiz, Bernardo; Brazzini, Augusto; Gonzales, Arturo; Castaneda-Zuniga, Wilfrido

2005-01-01

The purpose of this study was to report our initial experience with a swine model for biliary interventions by using a percutaneous transcholecystic access after suture anchor of the gallbladder. Telepaque tablets were given to five pigs to opacify the gallbladder. Under fluoroscopy, the opacified gallbladder was punctured percutaneously and three suture anchors were used to fix the anterior wall of the gallbladder to the abdominal wall. Two weeks later, the gallbladder was punctured and access into the distal common bile was obtained through the cystic duct. Balloon expandable stents were deployed into the distal common bile duct. Follow-up cholangiograms were obtained at 1 and 2 weeks. Necropsy was performed after 2 weeks to evaluate the relationship between the gallbladder and abdominal wall. Suture anchor placement was successful in all five pigs. One pig with a deep and highly positioned gallbladder developed fever, anorexia, and vomiting secondary to excessive stretch of the gallbladder. Placement of the guidewire through the extremely tortuous and small cystic ducts proved to be the most challenging step of the procedure. Metallic stents were successfully deployed in all four pigs in which it was attempted. Four animals tolerated the procedures without changes in their clinical conditions and no symptoms. Successful follow-up cholangiograms were performed at 1 and 2 weeks post-stent deployment without complications. All stents remained patent during the follow-up period. Necropsy demonstrated close attachment and adherence of the gallbladders to the antero-lateral abdominal wall in all four animals. Suture anchoring of the gallbladder is feasible in most pigs with superficially located gallbladders. This technique allows a safe and repeat access into the biliary system using a transcholecystic approach

Seismic response of unanchored and partially anchored liquid-storage tanks. Final report

International Nuclear Information System (INIS)

Malhotra, P.K.; Veletsos, A.S.

1995-12-01

Ground-mounted vertical storage tanks are important components of nuclear plant safety systems. A systematic study is made of the principal effects of base uplifting on the seismic response of laterally excited, unanchored and partially anchored cylindrical liquid-storage tanks. The study consists of two parts: the first deals with the static uplifting resistance of the flexible base plate, and the second deals with the dynamic response of the uplifting system. An insight into the behavior of the uplifting base plate is first gained with the help of a prismatic beam solution. In Section 2, the solution is implemented exactly, whereas in Section 3 it is implemented approximately by use of the Ritz energy procedure. Solutions are next presented for axisymmetrically and asymmetrically uplifted base plate of tanks, in Section 4. For the axisymmetric case the solution is implemented exactly, as well as approximately by modeling the plate by a series of semiinfinite prismatic beams. The accuracy of the latter approach is confirmed by comparing its predictions with those of the former. In Section 5, a highly efficient and rational method is presented for the dynamic response analysis of uplifting tanks. Both unanchored tanks and partially anchored tanks, for which the number of anchor bolts at the base is insufficient to ensure full fixity, are considered. It is shown that base uplifting may reduce significantly the hydrodynamic pressures, but these reductions may be associated with increased axial compressive stresses in the tank wall and large plastic rotations at the plate-shell junction. For partially anchored tanks, energy loss due to bolt yielding is found to be small

Bulk chirality effect for symmetric bistable switching of liquid crystals on topologically self-patterned degenerate anchoring surface.

Science.gov (United States)

Park, Min-Kyu; Joo, Kyung-Il; Kim, Hak-Rin

2017-06-26

We demonstrate a bistable switching liquid crystal (LC) mode utilizing a topologically self-structured dual-groove surface for degenerated easy axes of LC anchoring. In our study, the effect of the bulk elastic distortion of the LC directors on the bistable anchoring surface is theoretically analyzed for balanced bistable states based on a free energy diagram. By adjusting bulk LC chirality, we developed ideally symmetric and stable bistable anchoring and switching properties, which can be driven by a low in-plane pulsed field of about 0.7 V/µm. The fabricated device has a contrast ratio of 196:1.

Differences regarding job satisfaction and job involvement of psychologists with different dominant career anchors

OpenAIRE

CL Bester; T Mouton

2006-01-01

In order to contribute to higher levels of job satisfaction, job involvement , and productivity, a match or fit should be established between the dominant career anchor associated with a specific occupation and that of the employee. A career anchor is an individual’s set of self-perceived talents, abilities, motives, needs and values that form the nucleus of one’s occupational self-concept. Psychologists have always been part of the service orientated careers and therefore one would expect th...

Aggregate Effect on the Concrete Cone Capacity of an Undercut Anchor under Quasi-Static Tensile Load.

Science.gov (United States)

Marcon, Marco; Ninčević, Krešimir; Boumakis, Ioannis; Czernuschka, Lisa-Marie; Wan-Wendner, Roman

2018-05-01

In the last decades, fastening systems have become an essential part of the construction industry. Post-installed mechanical anchors are frequently used in concrete members to connect them with other load bearing structural members, or to attach appliances. Their performance is limited by the concrete related failure modes which are highly influenced by the concrete mix design. This paper aims at investigating the effect that different aggregates used in the concrete mix have on the capacity of an undercut anchor under tensile quasi-static loading. Three concrete batches were cast utilising three different aggregate types. For two concrete ages (28 and 70 days), anchor tensile capacity and concrete properties were obtained. Concrete compressive strength, fracture energy and elastic modulus are used to normalize and compare the undercut anchor concrete tensile capacity employing some of the most widely used prediction models. For a more insightful comparison, a statistical method that yields also scatter information is introduced. Finally, the height and shape of the concrete cones are compared by highly precise and objective photogrammetric means.

SiC2 siligraphene as a promising anchoring material for lithium-sulfur batteries: a computational study

Science.gov (United States)

Zhao, Yuming; Zhao, Jingxiang; Cai, Qinghai

2018-05-01

The development of stable and effective anchoring materials to immobilize the soluble lithium polysulfide (Li2Sn) species for suppressing their shuttle effects is vital for the large-scale practical applications of lithium-sulfur (Li-S) batteries. Here, by means of density functional theory (DFT) computations, the potential applications of the experimentally available SiC2 siligraphene (g-SiC2) as an anchoring material of Li-S batteries are systemically investigated. Our results reveal that g-SiC2 exhibits remarkable but not strong binding strength for the soluble Li2Sn species due to the S-Si and Li-C interactions. Especially, the intactness of the Li2Sn species and the good conductance of g-SiC2 can be well preserved after anchoring the Li2Sn species. The further comparative research demonstrate that g-SiC2 is superior to other siligraphenes, enabling it to be a very promising material as an ideal anchoring material for the immobilization of soluble Li2Sn species to avoid their dissolution into electrolyte.

4D modeling in a gimbaled linear accelerator by using gold anchor markers.

Science.gov (United States)

Miura, Hideharu; Ozawa, Shuichi; Matsuura, Takaaki; Kawakubo, Atsushi; Hosono, Fumika; Yamada, Kiyoshi; Nagata, Yasushi

2018-01-01

The purpose of this study was to verify whether the dynamic tumor tracking (DTT) feature of a Vero4DRT system performs with 10-mm-long and 0.28 mm diameter gold anchor markers. Gold anchor markers with a length of 10 mm and a diameter of 0.28 mm were used. Gold anchor markers were injected with short and long types into bolus material. These markers were sandwiched by a Tough Water (TW) phantom in the bolus material. For the investigation of 4-dimensional (4D) modeling feasibility under various phantom thicknesses, the TW phantom was added at 2 cm intervals (in upper and lower each by 1 cm). A programmable respiratory motion table was used to simulate breathing-induced organ motion, with an amplitude of 30 mm and a breathing cycle of 3 s. X-ray imaging parameters of 80 kV and 125 kV (320 mA and 5 ms) were used. The least detection error of the fiducial marker was defined as the 4D-modeling limitation. The 4D modeling process was attempted using short and long marker types and its limitation with the short and long types was with phantom thicknesses of 6 and 10 cm at 80 kV and 125 kV, respectively. However, the loss in detectability of the gold anchor because of 4D-modeling errors was found to be approximately 6% (2/31) with a phantom thickness of 2 cm under 125 kV. 4D-modeling could be performed except under the described conditions. This work showed that a 10-mm-long gold anchor marker in short and long types can be used with DTT for short water equivalent path length site, such as lung cancer patients, in the Vero4DRT system.

Poor Anchoring Limits Dyslexics' Perceptual, Memory, and Reading Skills

Science.gov (United States)

Oganian, Yulia; Ahissar, Merav

2012-01-01

The basic deficits underlying the severe and persistent reading difficulties in dyslexia are still highly debated. One of the major topics of debate is whether these deficits are language specific, or affect both verbal and non-verbal stimuli. Recently, Ahissar and colleagues proposed the "anchoring-deficit hypothesis" (Ahissar, Lubin,…

A Tenebrio molitor GPI-anchored alkaline phosphatase is involved in binding of Bacillus thuringiensis Cry3Aa to brush border membrane vesicles.

Science.gov (United States)

Zúñiga-Navarrete, Fernando; Gómez, Isabel; Peña, Guadalupe; Bravo, Alejandra; Soberón, Mario

2013-03-01

Bacillus thuringiensis Cry toxins recognizes their target cells in part by the binding to glycosyl-phosphatidyl-inositol (GPI) anchored proteins such as aminopeptidase-N (APN) or alkaline phosphatases (ALP). Treatment of Tenebrio molitor brush border membrane vesicles (BBMV) with phospholipase C that cleaves out GPI-anchored proteins from the membranes, showed that GPI-anchored proteins are involved in binding of Cry3Aa toxin to BBMV. A 68 kDa GPI-anchored ALP was shown to bind Cry3Aa by toxin overlay assays. The 68 kDa GPI-anchored ALP was preferentially expressed in early instar larvae in comparison to late instar larvae. Our work shows for the first time that GPI-anchored ALP is important for Cry3Aa binding to T. molitor BBMV suggesting that the mode of action of Cry toxins is conserved in different insect orders. Copyright © 2012 Elsevier Inc. All rights reserved.

Biomechanical comparison of an all-soft suture anchor with a modified Broström-Gould suture repair for lateral ligament reconstruction.

Science.gov (United States)

Brown, Christopher A; Hurwit, Daniel; Behn, Anthony; Hunt, Kenneth J

2014-02-01

Anatomic repair is indicated for patients who have recurrent lateral ankle instability despite nonoperative measures. There is no difference in repair stiffness, failure torque, or failure angle between specimens repaired with all-soft suture anchors versus the modified Broström-Gould technique with sutures only. Controlled laboratory study. In 10 matched pairs of human cadaveric ankles, the anterior talofibular ligament (ATFL) was incised from its origin on the fibula. After randomization, 1 ankle was repaired to its anatomic insertion using two 1.4-mm JuggerKnot all-soft suture anchors; the other ankle was repaired with a modified Broström-Gould technique using 2-0 FiberWire. All were augmented using the inferior extensor retinaculum. All ankles were mounted to the testing machine in 20° of plantar flexion and 15° of internal rotation and loaded to failure after the repair. Stiffness, failure torque, and failure angle were recorded and compared using a paired Student t test with a significance level set at P anchors pulled out of bone. The primary mode of failure was pulling through the ATFL tissue. There was no statistical difference in strength or stiffness between a 1.4-mm all-soft suture anchor and a modified Broström-Gould repair with 2-0 FiberWire. The primary mode of failure was at the tissue level rather than knot failure or anchor pullout. The particular implant choice (suture only, tunnel, anchor) in repairing the lateral ligament complex may not be as important as the time to biological healing. The suture-only construct as described in the Broström-Gould repair was as strong as all-soft suture anchors, and the majority of the ankles failed at the tissue level. For those surgeons whose preference is to use anchor repair, this novel all-soft suture anchor may be an alternative to other larger anchors, as none failed by pullout.

Progress on Poverty? New Estimates of Historical Trends Using an Anchored Supplemental Poverty Measure

Science.gov (United States)

Wimer, Christopher; Fox, Liana; Garfinkel, Irwin; Kaushal, Neeraj; Waldfogel, Jane

2016-01-01

This study examines historical trends in poverty using an anchored version of the U.S. Census Bureau’s recently developed Research Supplemental Poverty Measure (SPM) estimated back to 1967. Although the SPM is estimated each year using a quasi-relative poverty threshold that varies over time with changes in families’ expenditures on a core basket of goods and services, this study explores trends in poverty using an absolute, or anchored, SPM threshold. We believe the anchored measure offers two advantages. First, setting the threshold at the SPM’s 2012 levels and estimating it back to 1967, adjusted only for changes in prices, is more directly comparable to the approach taken in official poverty statistics. Second, it allows for a better accounting of the roles that social policy, the labor market, and changing demographics play in trends in poverty rates over time, given that changes in the threshold are held constant. Results indicate that unlike official statistics that have shown poverty rates to be fairly flat since the 1960s, poverty rates have dropped by 40 % when measured using a historical anchored SPM over the same period. Results obtained from comparing poverty rates using a pretax/pretransfer measure of resources versus a posttax/posttransfer measure of resources further show that government policies, not market incomes, are driving the declines observed over time. PMID:27352076

Progress on Poverty? New Estimates of Historical Trends Using an Anchored Supplemental Poverty Measure.

Science.gov (United States)

Wimer, Christopher; Fox, Liana; Garfinkel, Irwin; Kaushal, Neeraj; Waldfogel, Jane

2016-08-01

This study examines historical trends in poverty using an anchored version of the U.S. Census Bureau's recently developed Research Supplemental Poverty Measure (SPM) estimated back to 1967. Although the SPM is estimated each year using a quasi-relative poverty threshold that varies over time with changes in families' expenditures on a core basket of goods and services, this study explores trends in poverty using an absolute, or anchored, SPM threshold. We believe the anchored measure offers two advantages. First, setting the threshold at the SPM's 2012 levels and estimating it back to 1967, adjusted only for changes in prices, is more directly comparable to the approach taken in official poverty statistics. Second, it allows for a better accounting of the roles that social policy, the labor market, and changing demographics play in trends in poverty rates over time, given that changes in the threshold are held constant. Results indicate that unlike official statistics that have shown poverty rates to be fairly flat since the 1960s, poverty rates have dropped by 40 % when measured using a historical anchored SPM over the same period. Results obtained from comparing poverty rates using a pretax/pretransfer measure of resources versus a post-tax/post-transfer measure of resources further show that government policies, not market incomes, are driving the declines observed over time.

Lifestyle integration-gender based stereotypes: a study on Schein‟s career anchors within an ODeL HEI

Directory of Open Access Journals (Sweden)

Marili Williams

2014-01-01

Full Text Available This article is based on research that examined the differences between the aspirations of females and males in the workplace in terms of Schein‟s career anchors and enablers. The stereotype that females only work to ensure enhanced family lifestyles remains evident in the daily life of all (Hoobler, Lemmon & Wyane, 2014, p. 704; Mihail, 2006. Furthermore the stereotype that males‟ focus is much more ambitious in terms of reaching the highest managerial achievement/technical/ functional competence is regarded as a reality within society (Hoobler, Lemmon & Wyane, 2014, p. 704; Mihail, 2006. Insight into the question whether females work to live or live to work was investigated and this article reports on the differences between females and males regarding their work life ambitions. The data resulted from a quantitative research approach and the population consisted of 4 200 employees within an Open Distance electronic Learning (ODeL Higher Education Institution (HEI in South Africa. The focus was on the composition of a structured career conversation framework, using the original Schein career anchors (Schein, 1978; 1990; 1996 and the three-factor career-enabler model, developed by Grobler, Bezuidenhout and Rudolph (2014. Descriptive statistics, chi-square statistics as well as independent t-test analysis was used to identify the differences between genders with regard to career anchors and career enablers in different career stages. The results of the analysis illustrated that females focus more on the autonomy/independence- and lifestyle integration career anchors than males in the first 3 years of employment, thereafter their focus remains more on the lifestyle integration career anchor than males. Males however focus more on the general managerial career anchor in the first 3 years of their careers than women; and after 3 years males‟ focus moves more to the entrepreneurial creativity career anchor. The reported differences between

Bone-anchored maxillary expansion and bilateral interoral mandibular distraction osteogenesis in adult with severe obstructive sleep apnea syndrome.

Science.gov (United States)

Nie, Ping; Zhu, Min; Lu, Xiao-Feng; Fang, Bing

2013-05-01

Severe obstructive sleep apnea syndrome (OSAS) threatens patients' lives. To solve ventilation problem, snoring, and avoid another orthognathic surgery for mandibular advancement, bone-anchored rapid maxillary expansion and bilateral interoral mandibular distraction osteogenesis were tried on a 20-year-old Chinese male patient with severe skeletal class II malocclusion and OSAS.The patient had polysomnography (apnea-hypopnea index 54.2), body mass index measurement (19.7 kg/m), and cephalometry before the treatment. Bone-anchored rapid maxillary expansion was performed for the correction of maxillary transverse and minor sagittal deficiency and the improvement of nasal airflow by decreasing nasal resistance. Bilateral interoral mandibular distraction osteogenesis was operated to lengthen the small, retruded mandible by 15 mm. Orthodontic treatment after the maxillary expansion and mandibular distraction osteogenesis can help obtain stable occlusion.The Epworth Sleepiness Scale, a questionnaire for temporomandibular joint, cephalometric analysis, polysomnography, acoustic rhinometry, and multislice spiral computed tomography were performed to evaluate changes from the treatment. All the results showed that the patient had a significantly alleviated OSAS. In addition, an acceptable occlusion was also obtained.

Synergism Analysis of Bedding Slope with Piles and Anchor Cable Support under Sine Wave Vehicle Load

Directory of Open Access Journals (Sweden)

Li Dan-Feng

2016-01-01

Full Text Available Slope instability under dynamic load is the technical difficulty in the engineering; the evaluation of slope stability under dynamic load and the control of dynamic load is particularly important. In this paper, taking the right side slope of K27+140 m~380 m typical section (K27 slope for short in Chongqing Fuling-Fengdu-Shizhu expresses highway as an example to calculate and analyze. The K27 slope is under sinusoidal vehicle load and supported by anchor cable and antislide pile to resist downslide strength; at the same time, the combined effect of them is studied. Three-dimensional finite element methodology (FEM is used to simulate the bedding slope with piles and anchor cable support; furthermore, the eigenvalue can be obtained. In order to reduce error of the elastic boundary conditions caused by the reflection effect of wavelengths, the combination of Lysmer surface viscous boundary and traditional ground support boundaries is utilized to analyze and calculate the time-histories during bedding slope under dynamic load. The dynamic response of pile anchor support to resist sliding force is obtained. The concept of the pile anchor supporting coordinate interval is put forward. Furthermore, it is verified that the pile anchor supporting coordinate interval can be used to evaluate the stability of the slope under dynamic load and provide a new method for the control of the dynamic load.

Double row anchor fixation: a novel technique for a diabetic calanceal insufficiency avulsion fracture.

Science.gov (United States)

Greenhagen, Robert M; Highlander, Peter D; Burns, Patrick R

2012-01-01

Avulsion fractures of the calcaneal tuberosity represent only 1.3% to 2.7% of calcaneal fractures. These fractures are common pathologically in nature and attributed to decreased bone mineral density. Calcaneal insufficiency avulsion (CIA) fracture in patients with diabetes mellitus is most likely due to Charcot neuroarthropathy (CN) as described by the Brodsky classification (Brodsky 3B). Traditional open reduction and internal fixation is difficult in all calcaneal avulsion fractures because of poor bone quality. The authors report the first known description of the use of fracture fragment excision and double row anchor fixation.A 39-year-old woman with type I diabetes mellitus and a history of CN presented with an avulsion fracture of the calcaneal tuberosity. Excision of the fracture fragment and a gastrocnemius recession and reattachment of the Achilles tendon with double row anchor fixation to the calcaneus were performed. At 1 year, the patient's American Orthopaedic Foot & Ankle Society rearfoot score improved from 27/100 to 88/100. CIA fractures are an infrequently described injury. Because diabetes mellitus is frequently associated with this disease, it most likely represents a CN event. Traditionally, CIA fractures have been operatively treated with open reduction internal fixation. Previous authors have described difficulty with fixation because of poor quality. In the current report, the authors describe a novel operative approach to CIA fractures through the use of double row anchor fixation and excision of the fracture fragments. The authors feel that this previously undescribed treatment is superior to traditional methods and may serve as a new treatment option for all patients who have sustained this unusual pathology regardless of the underlying cause. The current authors provide a novel operative technique that provides inherent advantages to the traditional repair of CIA fractures. We believe CIA fractures represent a CN-type event and care

Quantifying Heuristic Bias: Anchoring, Availability, and Representativeness.

Science.gov (United States)

Richie, Megan; Josephson, S Andrew

2018-01-01

Construct: Authors examined whether a new vignette-based instrument could isolate and quantify heuristic bias. Heuristics are cognitive shortcuts that may introduce bias and contribute to error. There is no standardized instrument available to quantify heuristic bias in clinical decision making, limiting future study of educational interventions designed to improve calibration of medical decisions. This study presents validity data to support a vignette-based instrument quantifying bias due to the anchoring, availability, and representativeness heuristics. Participants completed questionnaires requiring assignment of probabilities to potential outcomes of medical and nonmedical scenarios. The instrument randomly presented scenarios in one of two versions: Version A, encouraging heuristic bias, and Version B, worded neutrally. The primary outcome was the difference in probability judgments for Version A versus Version B scenario options. Of 167 participants recruited, 139 enrolled. Participants assigned significantly higher mean probability values to Version A scenario options (M = 9.56, SD = 3.75) than Version B (M = 8.98, SD = 3.76), t(1801) = 3.27, p = .001. This result remained significant analyzing medical scenarios alone (Version A, M = 9.41, SD = 3.92; Version B, M = 8.86, SD = 4.09), t(1204) = 2.36, p = .02. Analyzing medical scenarios by heuristic revealed a significant difference between Version A and B for availability (Version A, M = 6.52, SD = 3.32; Version B, M = 5.52, SD = 3.05), t(404) = 3.04, p = .003, and representativeness (Version A, M = 11.45, SD = 3.12; Version B, M = 10.67, SD = 3.71), t(396) = 2.28, p = .02, but not anchoring. Stratifying by training level, students maintained a significant difference between Version A and B medical scenarios (Version A, M = 9.83, SD = 3.75; Version B, M = 9.00, SD = 3.98), t(465) = 2.29, p = .02, but not residents or attendings. Stratifying by heuristic and training level, availability maintained

High-resolution structure of TBP with TAF1 reveals anchoring patterns in transcriptional regulation.

Science.gov (United States)

Anandapadamanaban, Madhanagopal; Andresen, Cecilia; Helander, Sara; Ohyama, Yoshifumi; Siponen, Marina I; Lundström, Patrik; Kokubo, Tetsuro; Ikura, Mitsuhiko; Moche, Martin; Sunnerhagen, Maria

2013-08-01

The general transcription factor TFIID provides a regulatory platform for transcription initiation. Here we present the crystal structure (1.97 Å) and NMR analysis of yeast TAF1 N-terminal domains TAND1 and TAND2 bound to yeast TBP, together with mutational data. We find that yeast TAF1-TAND1, which in itself acts as a transcriptional activator, binds TBP's concave DNA-binding surface by presenting similar anchor residues to TBP as does Mot1 but from a distinct structural scaffold. Furthermore, we show how TAF1-TAND2 uses an aromatic and acidic anchoring pattern to bind a conserved TBP surface groove traversing the basic helix region, and we find highly similar TBP-binding motifs also presented by the structurally distinct TFIIA, Mot1 and Brf1 proteins. Our identification of these anchoring patterns, which can be easily disrupted or enhanced, provides insight into the competitive multiprotein TBP interplay critical to transcriptional regulation.

Influence of anchoring on miscarriage risk perception associated with amniocentesis.

Science.gov (United States)

Nuccio, Regina; Hashmi, S Shahrukh; Mastrobattista, Joan; Noblin, Sarah Jane; Refuerzo, Jerrie; Smith, Janice L; Singletary, Claire N

2015-04-01

One factor women consider when deciding whether to pursue amniocentesis is the risk of miscarriage. People use mechanisms like anchoring, or the prior belief regarding the magnitude of risk, as a frame of reference for new information. This study aimed to determine a woman's perception of miscarriage risk associated with amniocentesis before and after genetic counseling and to determine what factors anchor a woman's perception of miscarriage risk. One hundred thirteen women being seen for prenatal genetic counseling and possible amniocentesis at six Houston clinics participated in the two-part anonymous survey. While most women (56.7 %) perceived the risk as low or average pre-counseling and indicated the numeric risk of amniocentesis as risk as risk perception did not change after the genetic counseling session (60 %). Those who changed their feeling about the risk after counseling showed a decreased perception of the risk (p perception of the risk (p = 0.017) whereas those who declined amniocentesis were more likely to view the risk as high (p = 0.004). The only two anchoring factors that had an effect were having a friend or relative with a personal or family history of a genetic disorder (p = 0.001) and having a child already (p = 0.038); both were associated with a lower risk perception. The lack of significant factors may reflect the uniqueness of each patient's risk assessment framework and reinforces the importance of genetic counseling to elucidate individual concerns, particularly as non-invasive prenatal testing becomes more widely available and further complicates the prenatal testing landscape.

Treatment of chronic deltoid ligament injury using suture anchors.

Science.gov (United States)

Wang, Xu; Ma, Xin; Zhang, Chao; Wang, Chen; Huang, Jia-zhang

2014-08-01

To explore the efficacy of overlapping suture-anchor fixation for treatment of chronic deltoid ligament injury. Seventeen patients (11 men, 6 women of mean age 32.1 years [range, 18-58 years]) who had undergone surgery for chronic deltoid ligament injury from January 2007 to December 2011 were retrospectively analyzed. Preoperatively, they had undergone bilateral weight-bearing posterior-anterior radiographs, (MRI) and ultrasound examinations of the ankle. Ankle arthroscopy was performed to confirm the diagnosis, followed by surgery to clear intra-articular proliferating synovial tissues and remove cartilage debris and scar tissue. The deep layer of the deltoid ligament was sutured onto the tip of the medial malleolus and its superficial layer sutured onto its periosteum and fixed with suture anchors. American Orthopedic Foot and Ankle Society (AOFAS) scoring system for the ankle-hindfoot was used to evaluate the ankles pre- and post-operatively. The 17 patients were followed up for 12-34 months (mean 20.1 months). The angle between the long axes of the talus and first metatarsal and the hindfoot angle measured in a hindfoot alignment view (as described by Saltzman) were reduced from 5.4° ± 1.8° and 8.2° ± 2.6° preoperatively to 4.0° ± 0.9° and 5.3° ± 1.3° postoperatively, respectively. The mean AOFAS ankle-hindfoot score was 76.8 ± 7.0 preoperatively and 94.1 ± 3.3 at the last follow-up visit. Ten patients were scored as excellent, six as good, and one as fair. Pain was relieved in all patients and no patients had recurrent deltoid ligament injury. Using suture anchors to treat chronic deltoid ligament injury has relatively satisfactory outcomes. © 2014 Chinese Orthopaedic Association and Wiley Publishing Asia Pty Ltd.

Silver nanoparticles anchored reduced graphene oxide for enhanced electrocatalytic activity towards methanol oxidation

Science.gov (United States)

Kumar, Sanjeev; Mahajan, Mani; Singh, Rajinder; Mahajan, Aman

2018-02-01

In this report, silver nanoparticles (Ag NPs) anchored reduced graphene oxide (rGO) sheets (rGO/Ag) nanohybrid has been explored as anode material in direct methanol fuel cells (DMFCs). The synthesized rGO/Ag nanohybrid is characterized by XRD, XPS, FTIR spectroscopy and HRTEM techniques. Cyclic voltammograms demonstrate that the rGO/Ag nanohybrid exhibits higher electrocatalytic activity in comparison to rGO sheets for methanol oxidation reaction (MOR). This enhancement is attributed to the synergetic effect produced by the presence of more active sites provided by Ag NPs anchored on a conducting network of large surface area rGO sheets.

Psychological career resources as predictors of working adults’ career anchors: An exploratory study

Directory of Open Access Journals (Sweden)

Melinde Coetzee

2009-07-01

Full Text Available This study explored the relationship between the psychological career resources and career anchors of a sample of 2 997 working adults at predominantly managerial and supervisory levels in the service industry. The Psychological Career Resources Inventory and the Career Orientations Inventory were applied. Stepwise regression analyses indicated dimensions of psychological career resources as significant predictors of  participants’ career anchors. The findings add valuable new knowledge that can be used to inform organisational career development support practices as well as career counselling and guidance services concerned with promoting individuals’ employability and experiences of intrinsic career success.

Design of Ru(II) sensitizers endowed by three anchoring units for adsorption mode and light harvesting optimization

International Nuclear Information System (INIS)

Lobello, Maria Grazia; Fantacci, Simona; Manfredi, Norberto; Coluccini, Carmine; Abbotto, Alessandro; Nazeeruddin, Mohammed K.; De Angelis, Filippo

2014-01-01

We report the design, synthesis and computational investigation of a class of Ru(II)-dyes based on mixed bipyridine ligands for use in dye-sensitized solar cells. These dyes are designed to preserve the optimal anchoring mode of the prototypical N719 sensitizer by three carboxylic groups, yet allowing for tunable optimization of their electronic and optical properties by selective substitution at one of the 4-4′ positions of a single bipyridine ligand with π-excessive heteroaromatic groups. We used Density Functional Theory/Time Dependent Density Functional Theory calculations to analyze the electronic structure and optical properties of the dye and to investigate the dye adsorption mode on a TiO 2 nanoparticle model. Our results show that we are effectively able to introduce three carboxylic anchoring units into the dye and achieve at the same time an enhanced dye light harvesting, demonstrating the design concept. As a drawback of this type of dyes, the synthesis leads to a mixture of dye isomers, which are rather tedious to separate. - Highlights: • We designed heteroleptic Ru(II) sensitizers with three carboxylic anchoring groups. • The three carboxylic anchoring groups are essential for high open circuit potentials. • Introduction of the mixed bipyridine ligand increases the dye light absorption. • Computational simulations confirm the three anchoring sites on TiO 2

Design of Ru(II) sensitizers endowed by three anchoring units for adsorption mode and light harvesting optimization

Energy Technology Data Exchange (ETDEWEB)

Lobello, Maria Grazia; Fantacci, Simona [Computational Laboratory for Hybrid/Organic Photovoltaics (CLHYO), Istituto CNR di Scienze e Tecnologie Molecolari, Via elce di Sotto 8, I-06213 Perugia (Italy); Manfredi, Norberto; Coluccini, Carmine [Department of Materials Science and Milano-Bicocca Solar Energy Research Center-MIB-Solar, University of Milano-Bicocca and INSTM, Via Cozzi 53, I-20125 Milano (Italy); Abbotto, Alessandro, E-mail: alessandro.abbotto@unimib.it [Department of Materials Science and Milano-Bicocca Solar Energy Research Center-MIB-Solar, University of Milano-Bicocca and INSTM, Via Cozzi 53, I-20125 Milano (Italy); Nazeeruddin, Mohammed K., E-mail: mdkhaja.nazeeruddin@epfl.ch [Laboratory for Photonics and Interfaces, Station 6, Institute of Chemical Sciences and Engineering, School of Basic Sciences, Swiss Federal Institute of Technology, CH-1015 Lausanne (Switzerland); De Angelis, Filippo, E-mail: filippo@thch.unipg.it [Computational Laboratory for Hybrid/Organic Photovoltaics (CLHYO), Istituto CNR di Scienze e Tecnologie Molecolari, Via elce di Sotto 8, I-06213 Perugia (Italy)

2014-06-02

We report the design, synthesis and computational investigation of a class of Ru(II)-dyes based on mixed bipyridine ligands for use in dye-sensitized solar cells. These dyes are designed to preserve the optimal anchoring mode of the prototypical N719 sensitizer by three carboxylic groups, yet allowing for tunable optimization of their electronic and optical properties by selective substitution at one of the 4-4′ positions of a single bipyridine ligand with π-excessive heteroaromatic groups. We used Density Functional Theory/Time Dependent Density Functional Theory calculations to analyze the electronic structure and optical properties of the dye and to investigate the dye adsorption mode on a TiO{sub 2} nanoparticle model. Our results show that we are effectively able to introduce three carboxylic anchoring units into the dye and achieve at the same time an enhanced dye light harvesting, demonstrating the design concept. As a drawback of this type of dyes, the synthesis leads to a mixture of dye isomers, which are rather tedious to separate. - Highlights: • We designed heteroleptic Ru(II) sensitizers with three carboxylic anchoring groups. • The three carboxylic anchoring groups are essential for high open circuit potentials. • Introduction of the mixed bipyridine ligand increases the dye light absorption. • Computational simulations confirm the three anchoring sites on TiO{sub 2}.

76 FR 10627 - Assumption Buster Workshop: Trust Anchors Are Invulnerable

Science.gov (United States)

2011-02-25

... day-long workshop on the pros and cons of the use and implementation of trust anchors. The workshop... National Coordination Office (NCO) for the Networking and Information Technology Research and Development... Coordination Office for the Networking and Information Technology Research and Development (NITRD) Program on...

A radiographic investigation to determine the safety of suture anchor systems for pediatric modified Broström ankle ligament reconstruction.

Science.gov (United States)

Hazratwala, Kaushik; Best, Alistair; Kopplin, Matthew; Giza, Eric; Sullivan, Martin

2005-03-01

The modified Broström ligament reconstruction using anchor sutures has been performed in adults with clinical success; however, the safety parameters for the use of suture anchors in adolescent lateral ankle ligament reconstruction have not been established. To perform a radiographic analysis comparing the depth of penetration of suture anchors in adult ankle ligament reconstruction with the average distance of the physis from the tip of the fibula in adolescents. Cross-sectional study, Level of evidence, 4. Forty postoperative ankle radiographs of adult patients who had a modified Broström procedure were compared with 40 normal adolescent ankle radiographs. In the adult group, the distance of the suture anchor penetration from the distal tip of the fibula was measured; in the adolescent group, the distance of the physis from the distal tip of the fibula was measured. The mean depth of the suture anchors was 17 mm (range, 14-21 mm) from the tip of the fibula in the adult group, and the mean distance of the growth plate was 23 mm (range, 18-29 mm) in the adolescent group. Eight radiographs from the adolescent group (20%) had a physis measurement of ankle ligament repair in the skeletally immature patient using suture anchors.

Anchoring group effects in molecular devices: An ab initio study on the electronic transport of a carbon-dimer

International Nuclear Information System (INIS)

Wang, R.N.; Zheng, X.H.; Dai, Z.X.; Hao, H.; Song, L.L.; Zeng, Z.

2011-01-01

The conductance of a molecular device is sensitive to the contact geometry between the molecules and the probing electrodes. Taking a carbon-dimer C 2 as an example and connecting it to the electrodes by different linking atoms H, Cu and S, we investigate the anchoring group effect in molecular devices by the first-principles approaches. The results exhibit that, depending on the anchoring groups and the subsequent different metal-molecule chemical bonds, the current varies over more than two orders of magnitude under the same bias. This emphasizes the great importance of the anchoring groups in molecular devices.

Dependence of optical phase modulation on anchoring strength of dielectric shield wall surfaces in small liquid crystal pixels

Science.gov (United States)

Isomae, Yoshitomo; Shibata, Yosei; Ishinabe, Takahiro; Fujikake, Hideo

2018-03-01

We demonstrated that the uniform phase modulation in a pixel can be realized by optimizing the anchoring strength on the walls and the wall width in the dielectric shield wall structure, which is the needed pixel structure for realizing a 1-µm-pitch optical phase modulator. The anchoring force degrades the uniformity of the phase modulation in ON-state pixels, but it also keeps liquid crystals from rotating against the leakage of an electric field. We clarified that the optimal wall width and anchoring strength are 250 nm and less than 10-4 J/m2, respectively.

A Comparative Study of McDonald’s Wedding Narratives with the Model of Anchoring

Directory of Open Access Journals (Sweden)

Mimi Huang

2016-12-01

Full Text Available Fast-food giant McDonald’s announced in 2010 that they would start hosting wedding ceremonies and receptions for couples who would like to get married in their restaurants in Hong Kong. This paper conducts a study comparing the differing representations of McDonald’s wedding services through a narrative analytical approach. Specifically, this paper examines relevant discourses surrounding the launch of the corporation’s wedding services from the British media (e.g. Daily Mail, the Independent as well as public discourses in Hong Kong (e.g. McDonald’s Hong Kong website, and CNN’s Hong Kong news.  It is found that these narratives have a significant degree of discrepancy in depicting McDonald’s wedding stories. These differences further raise the question of how differing narrative strategies are employed to conceptualise the brand’s emergent wedding narratives in a unique social-cultural environment.  In the discussion of McDonald’s wedding stories, the focus is placed on the cognitive and linguistic aspects of the discourse. An analytical model of “anchoring” will be proposed and applied to investigate the cooperation’s marketing strategies as well as the media’s reaction towards such promotions. It is argued that a narrative can promote or demote a brand’s identity and position through the process of anchoring. It is further argued that anchoring is an important cognitive-psychological strategy in conceptualization and meaning construction. Keywords: narrative inquiry, cognitive narratology, anchors, anchoring, meaning construction

Supramolecule-Inspired Fabrication of Carbon Nanoparticles In Situ Anchored Graphene Nanosheets Material for High-Performance Supercapacitors.

Science.gov (United States)

Huang, Yulan; Gao, Aimei; Song, Xiaona; Shu, Dong; Yi, Fenyun; Zhong, Jie; Zeng, Ronghua; Zhao, Shixu; Meng, Tao

2016-10-12

The remarkable electrochemical performance of graphene-based materials has drawn a tremendous amount of attention for their application in supercapacitors. Inspired by supramolecular chemistry, the supramolecular hydrogel is prepared by linking β-cyclodextrin to graphene oxide (GO). The carbon nanoparticles-anchored graphene nanosheets are then assembled after the hydrothermal reduction and carbonization of the supramolecular hydrogels; here, the β-cyclodextrin is carbonized to carbon nanoparticles that are uniformly anchored on the graphene nanosheets. Transmission electron microscopy reveals that carbon nanoparticles with several nanometers are uniformly anchored on both sides of graphene nanosheets, and X-ray diffraction spectra demonstrate that the interlayer spacing of graphene is enlarged due to the anchored nanoparticles among the graphene nanosheets. The as-prepared carbon nanoparticles-anchored graphene nanosheets material (C/r-GO-1:3) possesses a high specific capacitance (310.8 F g -1 , 0.5 A g -1 ), superior rate capability (242.5 F g -1 , 10 A g -1 ), and excellent cycle stability (almost 100% after 10 000 cycles, at the scan rate of 50 mV s -1 ). The outstanding electrochemical performance of the resulting C/r-GO-1:3 is mainly attributed to (i) the presence of the carbon nanoparticles, (ii) the enlarged interlayer spacing of the graphene sheets, and (iii) the accelerated ion transport rates toward the interior of the electrode material. The supramolecule-inspired approach for the synthesis of high-performance carbon nanoparticles-modified graphene sheets material is promising for future application in graphene-based energy storage devices.

Effect of historical earthquakes on pre-stressed anchor tie back diaphragm wall and on near-by building

Directory of Open Access Journals (Sweden)

Kamal Mohamed Hafez Ismail Ibrahim

2013-04-01

Full Text Available Pre-stressed tie back anchored diaphragm walls are considered one of the safest lateral supports which help in overall stability when there is a significant difference in land level between back and front of these walls. Permanent lateral supports to these walls are frequently represented by supporting it laterally with foundation and floor slabs of the building. In this paper a special study of one raw anchor diaphragm wall subjected to different earthquake dynamic loads will be presented. The wall retains an excavation of 9.5 m and supports laterally a near-by 5 floor building. Five historical strong motions with different fundamental frequencies are subjected on the wall. The wall displacement, straining actions, anchor extreme force and the influence of variation of anchor stiffness are calculated using a dynamic Plaxis finite element program. The soil is considered as elasto-plastic material and represented using Mohr–Coulomb criteria, the wall and the anchor are considered to behave elastically. Prescribed displacement at the lower bottom boundary represents the earthquake motion. Far left and right absorbent boundaries are assumed to prevent dynamic wave reflection. Four static phases representing construction procedure and one dynamic loading phase are considered. It is found that the straining actions of different historical earthquakes match in shape with each other, the only change is in the amplitude which is affected by earthquake fundamental frequency and its intensity. The maximum dynamic lateral displacement of the wall is at its free top. The near-by building shows a differential settlement towards the wall which causes a change in the sign and amplitude of the straining actions. Increasing the stiffness of anchor was also studied and it was found that it reduces too much the maximum dynamic top wall lateral displacement.

Local ecological knowledge (LEK) on fish behavior around anchored FADs

NARCIS (Netherlands)

Macusi, Edison D.; Abreo, Neil A.S.; Babaran, Ricardo P.

2017-01-01

The Fishing Industry in the Philippines plays an important role in the food and employment need of Filipino fishers. By using anchored Fish Aggregating Devices (FADs or payao), the Philippine tuna fisheries was transformed into a million-dollar industry. Minimal studies on exploitation rates and

Utility of gel nails in improving the appearance of cosmetically disfigured nails: Experience with 25 cases

Directory of Open Access Journals (Sweden)

Soni Nanda

2014-01-01

Full Text Available Background: Gel nails are a commonly used cosmetic procedure, though their use by dermatologists has not been evaluated. These can be used to improve the appearance of cosmetically disfigured nails where other treatment options have failed; the condition is self-limiting or irreversible; or to camouflage the dystrophy until healing. Materials and Methods: A prospective, uncontrolled, open-label study on 25 participants presenting with cosmetically disfigured nails was undertaken. Mycologically negative, consenting patients with various nail plate surface abnormalities like trachyonychia (n =8; superficial pitting (n =6; onychorrhexis (n =4; superficial pitting with onychoschizia (n =3; Beau′s lines (n =3 and pterygium (n =1 were included. The patients received gel nail application using Ranara gel nail kit ® . Extra care was taken to avoid any damage to cuticle. Standard pre- and post-treatment photographs were taken to assess improvement. Patient satisfaction score (1-10; Global assessment score of improvement (no improvement to excellent improvement and any side effects reported were recorded. Results: The average age of treated patients was 30.44±11.39 years (range 18-60 years. A total of 69 nails were treated (average of 2.76 per patient. Post-procedure, the average patient satisfaction score was 9.08 ± 0.86 (range 7-10. The Global assessment showed excellent improvement (40% cases; good improvement (56% cases and mild improvement in the single case of pterygium treated. Conclusions: The use of Gel nails in patients with cosmetically disfiguring nail plate surface abnormalities (like trachyonychia, onychoschizia, pitting, etc. was found to produce good to excellent improvement in most of the cases. The patient satisfaction with the procedure was rated as high. This, coupled with absence of side effects, make gel nails a valuable tool in improving cosmesis and satisfaction among patients presenting with nail plate surface abnormalities

Anchoring device enabling relaxation of a multi-strand prestressing cable

International Nuclear Information System (INIS)

1979-01-01

Anchoring device, in a concrete structure, for a multi-strand prestressing cable, enabling the cable to be stressed or relaxed, comprising: (a) an axisymmetrical block, fitted with channels to enable the cable strands to be stressed and anchored through this block, (b) a duct with its opening splayed to a diameter greater than that of the block over a length corresponding to the stretching of the cable when being stressed, (c) a round bearing plate on the concrete around the expanded hole of the duct and (d) at least one intermediate removable bearing piece coming between the edge of the block and the internal edge of the plate. The removable parts are crown sectors of which the opposite bearing faces of each are slanted with respect to the centre line of the block and orientated in the same direction so as to transmit the cable stress at an angle from the block to the edge of the bearing plate [fr

Radiocarbon dates of the medieval period stone anchors from Dabhol, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.; Vora, K.H.

(Table 1) belong to Indo-Arab type and are similar to those reported from Dwarka, Bet Dwarka, Miyani, Visawada and Mithivirdi on the Saurash- tra coast 8 , and also on the Tamil Nadu coast 9 . Anchor 1 is with lower portion broad and tapers upper... the history of the place as a port/harbour. The anchors are similar to those reported from other places on the coast of India and the other Indian Ocean countries, including Dwarka 10 , Bet Dwarka 11 , Miyani and Visawada 12 , Somnath 13 and Mithivirdi...

Metallurgical evaluation of failed post-tensioned containment tendon anchors at Joseph M. Farley Unit 2

International Nuclear Information System (INIS)

Czajkowski, C.J.

1986-01-01

A metallurgical examination has been performed on three failed post-tensioned containment tendon anchors and one intact anchor from the Farley Unit 2 Nuclear Power Station. The evaluation consisted of chemical/mechanical testing, optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. The conclusions drawn from the investigation were: 1) the anchors met the chemical and mechanical properties of AISI 4140/4142 steel; 2) there was no evidence of phosphorous segregation to the grain boundary (by ethereal picral etch); 3) the observed cracking was generally a mixed mode of intergranular and quasi-cleavage as well as ductile rupture with the intergranular cracking occurring along prior austenite grain boundaries; 4) the results of the mechanical tests coupled with the discontinuous nature of the intergranular areas and the elimination of other modes of failure give sufficient indication that the failure was a hydrogen induced cracking phenomenon

Hypomorphic mutations in PGAP2, encoding a GPI-anchor-remodeling protein, cause autosomal-recessive intellectual disability

DEFF Research Database (Denmark)

Hansen, Lars; Tawamie, Hasan; Murakami, Yoshiko

2013-01-01

PGAP2 encodes a protein involved in remodeling the glycosylphosphatidylinositol (GPI) anchor in the Golgi apparatus. After synthesis in the endoplasmic reticulum (ER), GPI anchors are transferred to the proteins and are remodeled while transported through the Golgi to the cell membrane. Germline...... mutations in six genes (PIGA, PIGL, PIGM, PIGV, PIGN, and PIGO) in the ER-located part of the GPI-anchor-biosynthesis pathway have been reported, and all are associated with phenotypes extending from malformation and lethality to severe intellectual disability, epilepsy, minor dysmorphisms, and elevated...... alkaline phosphatase (ALP). We performed autozygosity mapping and ultra-deep sequencing followed by stringent filtering and identified two homozygous PGAP2 alterations, p.Tyr99Cys and p.Arg177Pro, in seven offspring with nonspecific autosomal-recessive intellectual disability from two consanguineous...

The relation between career anchors, occupational types and job satisfaction of midcareer employees

Directory of Open Access Journals (Sweden)

J. A. Ellison

2000-06-01

Full Text Available The objective of this research was to determine the value of the career anchor model in career decision-making. Career models that can provide the individual with greater self-insight can serve as an important guide when making career choices in todays turbulent working environment. Two hundred and ninety-five midcareer employees (managerial and non-managerial completed questionnaires to determine their career anchor, occupation type and levels of general, intrinsic and extrinsic job satisfaction. The differences in job satisfaction between employees with a fit between career anchor and occupational type and those with no such fit were compared. It was found that respondents with a fit had a significantly higher level of general and intrinsic job satisfaction than those with no such fit. It is therefore suggested that the career anchor construct could probably serve as a useful tool for midcareer employees to make career choices. Opsomming Die doel van hierdie ondersoek was om die waarde van die loopbaanankermodel in loopbaanbesluitneming te bepaal. Loopbaanmodelle wat individue van groter insig kan voorsien kan as n belangrike riglyn in vandag se turbulente werksomgewing dien. Tweehonderd vyf-en-negentig middelloopbaan-werknemers (bestuur en nie-bestuur het vraelyste voltooi om hulle loopbaanankers, beroepstipe en vlakke van algemene, intrinsieke en ekstrinsieke werkstevredenheid te bepaal. Die verskille in werkstevredenheid tussen werknemers met n passing tussen loopbaananker en beroepstipe en die sender n sodanige passing, is vergelyk. Daar is bevind dat respondente met n passing 'n beduidende hoer vlak van algemene en intrinsieke werkstevredenheid het as die sender so 'n passing. Daar word derhalwe voorgestel dat die loopbaanankermodel waarskynlik as n nuttige instrument by middelloopbaan-werknemers gebruik kan word om loopbaanbesluite te neem.

Anchoring platinum on graphene using metallic adatoms: a first principles investigation

International Nuclear Information System (INIS)

Sen, F G; Alpas, A T; Qi, Y

2012-01-01

First principles calculations based on spin-polarized density functional theory were used to identify metallic adatoms that would strengthen the Pt(111)/graphene interface (with a low work of separation of 0.009 J m -2 ), when the adatom was placed between the Pt(111) and the graphene. It was shown that the strength of the Pt-adatom bond, which had a metallic character, increased with the amount of charge transferred from the adatom to the Pt. The carbon-adatom bond, on the other hand, had a mixed ionic and covalent character and was weaker than the Pt-adatom bond for each of the 25 elements considered. Consequently, the total Pt(111)/graphene interface strength and, hence, the anchoring effect of the adatom were controlled by the carbon-adatom bond strength. Metals with unfilled d orbitals increased the Pt/graphene interface strength to above 0.5 J m -2 . The carbon-adatom bond strength was proportional to the ratio between the charge transferred from the adatom to the graphene (ΔZ C ) and the charge transferred to the Pt surface (ΔZ Pt ); i.e., the ΔZ C /ΔZ Pt ratio defined the ability of an adatom to anchor Pt to graphene. For Ir, Os, Ru, Rh and Re, ΔZ C /ΔZ Pt > 1.0, making these elements the most effective adatoms for anchoring Pt to graphene. (paper)

Dynamic Rewiring of Promoter-Anchored Chromatin Loops during Adipocyte Differentiation

DEFF Research Database (Denmark)

Siersbæk, Rasmus; Madsen, Jesper Grud Skat; Javierre, Biola Maria

2017-01-01

-C to demonstrate a rapid reorganization of promoter-anchored chromatin loops within 4 hr after inducing differentiation of 3T3-L1 preadipocytes. The establishment of new promoter-enhancer loops is tightly coupled to activation of poised (histone H3 lysine 4 mono- and dimethylated) enhancers, as evidenced...

Development of the Career Anchors Scale among Occupational Health Nurses in Japan.

Science.gov (United States)

Kubo, Yoshiko; Hatono, Yoko; Kubo, Tomohide; Shimamoto, Satoko; Nakatani, Junko; Burgel, Barbara J

2016-11-29

This study aimed to develop the Career Anchors Scale among Occupational Health Nurses (CASOHN) and evaluate its reliability and validity. Scale items were developed through a qualitative inductive analysis of interview data, and items were revised following an examination of content validity by experts and occupational health nurses (OHNs), resulting in a provisional scale of 41 items. A total of 745 OHNs (response rate 45.2%) affiliated with the Japan Society for Occupational Health participated in the self-administered questionnaire survey. Two items were deleted based on item-total correlations. Factor analysis was then conducted on the remaining 39 items to examine construct validity. An exploratory factor analysis with a main factor method and promax rotation resulted in the extraction of six factors. The variance contribution ratios of the six factors were 37.45, 7.01, 5.86, 4.95, 4.16, and 3.19%. The cumulative contribution ratio was 62.62%. The factors were named as follows: Demonstrating expertise and considering position in work (Factor 1); Management skills for effective work (Factor 2); Supporting health improvement in groups and organizations (Factor 3); Providing employee-focused support (Factor 4); Collaborating with occupational health team members and personnel (Factor 5); and Compatibility of work and private life (Factor 6). The confidence coefficient determined by the split-half method was 0.85. Cronbach's alpha coefficient for the overall scale was 0.95, whereas those of the six subscales were 0.88, 0.90, 0.91, 0.80, 0.85, and 0.79, respectively. CASOHN was found to be valid and reliable for measuring career anchors among OHNs in Japan.

Development of the Career Anchors Scale among Occupational Health Nurses in Japan

Science.gov (United States)

Kubo, Yoshiko; Hatono, Yoko; Kubo, Tomohide; Shimamoto, Satoko; Nakatani, Junko; Burgel, Barbara J.

2016-01-01

Objectives: This study aimed to develop the Career Anchors Scale among Occupational Health Nurses (CASOHN) and evaluate its reliability and validity. Methods: Scale items were developed through a qualitative inductive analysis of interview data, and items were revised following an examination of content validity by experts and occupational health nurses (OHNs), resulting in a provisional scale of 41 items. A total of 745 OHNs (response rate 45.2%) affiliated with the Japan Society for Occupational Health participated in the self-administered questionnaire survey. Results: Two items were deleted based on item-total correlations. Factor analysis was then conducted on the remaining 39 items to examine construct validity. An exploratory factor analysis with a main factor method and promax rotation resulted in the extraction of six factors. The variance contribution ratios of the six factors were 37.45, 7.01, 5.86, 4.95, 4.16, and 3.19%. The cumulative contribution ratio was 62.62%. The factors were named as follows: Demonstrating expertise and considering position in work (Factor 1); Management skills for effective work (Factor 2); Supporting health improvement in groups and organizations (Factor 3); Providing employee-focused support (Factor 4); Collaborating with occupational health team members and personnel (Factor 5); and Compatibility of work and private life (Factor 6). The confidence coefficient determined by the split-half method was 0.85. Cronbach's alpha coefficient for the overall scale was 0.95, whereas those of the six subscales were 0.88, 0.90, 0.91, 0.80, 0.85, and 0.79, respectively. Conclusions: CASOHN was found to be valid and reliable for measuring career anchors among OHNs in Japan. PMID:27725484

MAIL1 is essential for development of the primary root but not of anchor roots

OpenAIRE

Ühlken, Christine; Hoth, Stefan; Weingartner, Magdalena

2014-01-01

MAIN-LIKE1 (MAIL1) is a ubiquitously expressed nuclear protein, which has a crucial function during root development. We have recently described loss of function mutants for MAIL1, in which the organization and function of the primary root meristem is lost soon after germination. Moreover cell differentiation is impaired resulting in primary root growth arrest soon after emergence. Here we show that mail1 mutants form several anchor roots from the hypocotyl to root junction. These anchor root...

The biggest stone anchors (Indo-Arab type) from Mithi Virdi, Bhavnagar, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Kumar, B.

of Oceanography, Goa on the Saurashtra coast have been undertaken at Dwarka (Gaur et al. 2000), Bet Dwarka (Sundaresh et al. 2002) and Somnath {Gaur et al. 2002). The prospections *National Institute of Oceanography, Dona Paula, Goa **Devli, Talaza, Bhavnagar... of stone anchors at Dwarka, Bet Dwarka, Aramda (Gaur et al. 2003), Somnath (Gaur ef al. 2002), Vijayadurg (Sila ef al. 1998), Sindhudurg (Sila and Gaur 1997), Goa waters (Sila et al. 2003) and Tamilnadu coast (Athiyaman 2001). These anchors...

Early functional outcome of a modified Brostrom-Gould surgery using bioabsorbable suture anchor for chronic lateral ankle instability.

Science.gov (United States)

Shahrulazua, A; Ariff Sukimin, M S; Tengku Muzaffar, T M; Yusof, M I

2010-03-01

The purpose of this study was to evaluate the early functional outcome following the use of a bioabsorbable suture anchor to simplify the repair of injured lateral ankle structures as a variation of an established technique known as the Brostrom-Gould procedure. This was a prospective study of 30 ankles with chronic lateral instability that underwent a modified Brostrom-Gould surgery using a bioabsorbable suture anchor, performed by a single surgeon. A total of 29 patients, aged 15 to 52 (mean is 33) years, were enrolled in the study. The follow-up period ranged from three to six (mean is four) months. The function of the patients' ankles was scored using the Kaikkonen Functional Scale, both preoperatively and postoperatively. Preoperatively, all ankles had poor scores (less than 50). Postoperatively, 28 ankles showed excellent scores and two ankles showed good scores, while none obtained a fair or poor score. The difference in the overall means between the postoperative and preoperative scores was statistically significant (p-value is 0.001). Post surgery, 24 ankles had no symptoms, while six had only mild ankle tightness with extreme inversion movement at the last review. All patients were able to walk normally, and 29 ankles regained their normal running capability. There was marked improvement in the ability to descend stairs, to rise on heels and toes, to perform a single-limb stance, and in range of motions of the ankle dorsiflexion as well as in ankle laxity. The modified Brostrom-Gould procedure using a bioabsorbable suture anchor allowed for early ankle rehabilitation and offered a reproducible and excellent early functional outcome with minimal complications.

Strength of suture anchor versus transosseous tunnel in anatomic reconstruction of the ankle lateral ligaments: a biomechanical study.

Science.gov (United States)

Li, Hong-Yun; Hua, Ying-Hui; Wu, Zi-Ying; Chen, Bo; Chen, Shi-Yi

2013-11-01

The purpose of this study was to compare the biomechanical characteristics of fixation with 2-suture anchors versus transosseous tunnel fixation in anatomic reconstruction of the ankle lateral ligaments. Six matched pairs of human cadaveric ankles underwent anatomic lateral ankle reconstruction, and fixation of the graft on the talus was achieved with 2 suture anchors or a transosseous tunnel. Ankles for the transosseous tunnel group were chosen at random, with the paired contralateral ankles used for the 2-suture anchor group. Half of the peroneus brevis tendon was harvested as a graft. For each technique, one end of the tendon was secured to the original insertion point of the anterior talofibular ligament (ATFL) at the talus, whereas the other end was armed with 2 No. 5 nonabsorbable sutures (Ethicon, Somerville, NJ) and passed through the bone tunnel in the fibula. Biomechanical testing was performed by applying the force in line with the graft. Load to failure was determined at a displacement rate of 50 mm/min. The load-displacement curve, maximum load at failure (N), and stiffness (N/mm) were recorded and compared between the 2 techniques. There was no difference between constructs in the 2-suture anchor group and the transosseous tunnel group in terms of the ultimate load and stiffness (161.8 ± 47.6 N v 171.9 ± 76.0 N; P = .92; 4.59 ± 1.85 N/mm v 5.77 ± 1.98 N/mm; P = .35). Most constructs failed because of anchor pullout in the 2-suture anchor group (5 of 6) and fracture of the bony bridge in the transosseous tunnel group (6 of 6). The strength of fixation with suture anchors in anatomic reconstruction of the ankle lateral ligaments was equivalent to transosseous tunnel fixation as determined with biomechanical testing. However, this study did not prove that one is advantageous over the other. Both techniques showed excellent biomechanical results. Therefore, the 2-suture anchor fixation approach can be safely used in anatomic reconstruction of the

Test results on the dynamic testing of expansion type concrete anchors

International Nuclear Information System (INIS)

Barron, B.; Rice, R.; Stephen, R.M.

1974-12-01

Tests were performed to determine the structural response of commercially available expansion type anchors for the FFTF when subjected to dynamic loadings similar to machine vibrations and earthquakes. The specimens were subjected to tension, shear, and combined shear-tension loads

Robust conductance of dumbbell molecular junctions with fullerene anchoring groups

DEFF Research Database (Denmark)

Markussen, Troels; Settnes, Mikkel; Thygesen, Kristian Sommer

2011-01-01

The conductance of a molecular wire connected to metallic electrodes is known to be sensitive to the atomic structure of the molecule-metal contact. This contact is to a large extent determined by the anchoring group linking the molecular wire to the metal. It has been found experimentally that a...

The development of argon arc brazing with Cu-based filler for ITER thermal anchor attachment

International Nuclear Information System (INIS)

Sun Zhenchao; Li Pengyuan; Pan Chuanjie; Hou Binglin; Han Shilei; Pei Yinyin; Long Weimin

2012-01-01

Thermal anchor is the key component of ITER magnet supports to maintain the low temperature for the nor mal operation of superconducting coils. During the advanced research of ITER thermal anchor attachment, dozens of brazing filler and several kinds of brazing technique have been developed and investigated. The test result shows that Cu-based alloy have the preferable mechanical properties at both room temperature and liquid nitrogen temperatures (77 K) for high brazing temperature. And it has a good weldability to 316LN. The brazing temperature of Cu-based filler is over 1000℃, but heat input is relatively low for shallower heating depth of argon arc brazing. Lower heat input is good for the control of brazing deformation. It is no need to clean after brazing because for argon arc brazing there is no bra- zing flux used. Arc brazing with Cu-based filler was chosen as the principal method for the attachment of thermal anchor. (authors)

Anchor effects in decision making can be reduced by the interaction between goal monitoring and the level of the decision maker's executive functions.

Science.gov (United States)

Schiebener, Johannes; Wegmann, Elisa; Pawlikowski, Mirko; Brand, Matthias

2012-11-01

Models of decision making postulate that interactions between contextual conditions and characteristics of the decision maker determine decision-making performance. We tested this assumption by using a possible positive contextual influence (goals) and a possible negative contextual influence (anchor) in a risky decision-making task (Game of Dice Task, GDT). In this task, making advantageous choices is well known to be closely related to a specific decision maker variable: the individual level of executive functions. One hundred subjects played the GDT in one of four conditions: with self-set goal for final balance (n = 25), with presentation of an anchor (a fictitious Top 10 list, showing high gains of other participants; n = 25), with anchor and goal definition (n = 25), and with neither anchor nor goal setting (n = 25). Subjects in the conditions with anchor made more risky decisions irrespective of the negative feedback, but this anchor effect was influenced by goal monitoring and moderated by the level of the subjects' executive functions. The findings imply that impacts of situational influences on decision making as they frequently occur in real life depend upon the individual's cognitive abilities. Anchor effects can be overcome by subjects with good cognitive abilities.

Semantic attributes for people's appearance description: an appearance modality for video surveillance applications

Science.gov (United States)

Frikha, Mayssa; Fendri, Emna; Hammami, Mohamed

2017-09-01

Using semantic attributes such as gender, clothes, and accessories to describe people's appearance is an appealing modeling method for video surveillance applications. We proposed a midlevel appearance signature based on extracting a list of nameable semantic attributes describing the body in uncontrolled acquisition conditions. Conventional approaches extract the same set of low-level features to learn the semantic classifiers uniformly. Their critical limitation is the inability to capture the dominant visual characteristics for each trait separately. The proposed approach consists of extracting low-level features in an attribute-adaptive way by automatically selecting the most relevant features for each attribute separately. Furthermore, relying on a small training-dataset would easily lead to poor performance due to the large intraclass and interclass variations. We annotated large scale people images collected from different person reidentification benchmarks covering a large attribute sample and reflecting the challenges of uncontrolled acquisition conditions. These annotations were gathered into an appearance semantic attribute dataset that contains 3590 images annotated with 14 attributes. Various experiments prove that carefully designed features for learning the visual characteristics for an attribute provide an improvement of the correct classification accuracy and a reduction of both spatial and temporal complexities against state-of-the-art approaches.

Research on mobile strategy of anchor node based on weighted virtual force model%基于加权虚拟力模型的锚节点移动策略的研究

Institute of Scientific and Technical Information of China (English)

魏连锁; 蔡绍滨; 潘实

2017-01-01

The existing mobility strategy of the anchor node in wireless sensor network (WSN) has the shortcomings of too long moving path and low positioning accuracy when the anchor node traverses the network voids area. A new mobility strategy of WSN anchor node was proposed based on an improved virtual forces model. The number of neighbor nodes and the distance between the neighbor nodes to the anchor nodes were introduced as their own dense weight attributes. The unknown nodes in-tensity was used as weights to improve the traditional virtual force model. Meantime the distance-measuring errorε was taken into account. The optimal distribution, direction selection, shift step length and fallback strategy of anchor node could be ana-lyzed by the trilateration. Using the number of virtual beacon received by the unknown node and the distance between the un-known node to the anchor node calculate the virtual force. Then according to the virtual force, the direction was chosen and the anchor nodes were moved. Simulation experiments show that the strategy can make the anchor nodes move according to the specific circumstances of unknown node distribution. It has a high positioning accuracy and strong adaptability. It can success-fully shorten the path of the anchor node movement and reduce the number of virtual beacon. Moreover it can effectively avoid the anchor node to enter the network voids area and reduce the number of collinear virtual anchor nodes.%针对现有无线传感器网络(WSN)锚节点移动策略不能有效避免遍历网络空洞区域时引起的移动路径过长、定位精度低等缺点,提出一种基于改进虚拟力模型的无线传感器网络锚节点移动策略.将未知节点的邻居节点数量及其到邻居节点的距离作为自身的密集权重属性,利用未知节点的密集度作为权值来改进传统的虚拟力模型.同时考虑测距误差ε的大小,利用三边测量法分析锚节点的最优分�

The improved oval forceps suture-guiding method for minimally invasive Achilles tendon repair.

Science.gov (United States)

Liu, Yang; Lin, Lixiang; Lin, Chuanlu; Weng, Qihao; Hong, Jianjun

2018-06-01

To discuss the effect and advantage of the improved oval forceps suture-guiding method combined with anchor nail in the treatment of acute Achilles tendon rupture. A retrospective research was performed on 35 cases of acute Achilles tendon rupture treated with the improved oval forceps suture-guiding method from January 2013 to October 2016. Instead of the Achillon device, we perform the Achillon technique with the use of simple oval forceps, combined with absorbable anchor nail, percutaneously to repair the acute Achilles tendon rupture. All patients were followed up for at least 12 months (range, 12-19 months), and all the patients underwent successful repair of their acute Achilles tendon rupture using the improved oval forceps suture-guiding method without any major intra- or postoperative complications. All the patients returned to work with pre-injury levels of activity at a mean of 12.51 ± 0.76 weeks. Mean AOFAS ankle-hindfoot scores improved from 63.95 (range, 51-78) preoperatively to 98.59 (range, 91-100) at last follow-up. This was statistically significant difference (P anchor nail, the improved technique has better repair capacity and expands the operation indication of oval forceps method. Copyright © 2018 Elsevier Ltd. All rights reserved.

Material and welding development of anchor plates to build nuclear power plant by blue arc process

International Nuclear Information System (INIS)

Gibelli, C.E.

1986-01-01

To build nuclear power plants, anchor plates are plenty used. These anchor plates serve as a system with the purpose to fix many heavy components or a simple stair. Considering the necessity of element fabrication fastly, with reasonable economy and quality, the arc study welding process (blue arc) was used. A special development of the material concept as well as a welding procedure and a subsuppliers qualification of the raw material was necessary. (Author) [pt

Fixation of a human rib by an intramedullary telescoping splint anchored by bone cement.

Science.gov (United States)

Liovic, Petar; Šutalo, Ilija D; Marasco, Silvana F

2016-09-01

A novel concept for rib fixation is presented that involves the use of a bioresorbable polymer intramedullary telescoping splint. Bone cement is used to anchor each end of the splint inside the medullary canal on each side of the fracture site. In this manner, rib fixation is achieved without fixation device protrusion from the rib, making the splint completely intramedullary. Finite element analysis is used to demonstrate that such a splint/cement composite can preserve rib fixation subjected to cough-intensity force loadings. Computational fluid dynamics and porcine rib experiments were used to study the anchor formation process required to complete the fixation.

The Naturalized Nation: Anchoring, Objectification and Naturalized Social Representations of History

Directory of Open Access Journals (Sweden)

Eemeli Hakoköngäs

2016-12-01

Full Text Available This study focuses on the connection between social representations of history and collective memory from the perspective of elementary concepts of social representations theory: anchoring, objectification and naturalization. The aims of the study are to arrive at a conceptual clarity of this connection and demonstrate how to apply basic concepts of social representations theory to the study of collective memory. The study also focuses on the naturalized characteristics of Finnish history. The data consist of the covers of twenty Finnish history books between the years 1965 and 2014. All the covers are embellished with typography or visual images. The covers were analysed using a semiotic approach in which the interest is in the description (denotation, the associations (connotation and the meaning system these construe (myth. The analysis shows how national history is concretized with visual images (objectification, how the meaning of representation is conveyed (anchoring and how collective memory is maintained (naturalization, transmitted and shaped during the years. The results show how the stable collective memories and changing social representations of history are interacting. The most frequently used visual element was the colour blue, which alludes to the Finnish flag, a symbol of the nation that represents the core of Finnish history. The study suggests that it is possible to conceptualize collective memories as naturalized social representations of history. It shows how processes of anchoring and objectification serve as tools of collective memory and how the naturalized conceptions are subtly changed. In addition, the study develops the use of visual semiotic analysis in social representations research.

Rhenium and technetium: application of organometallic rhenium and technetium complexes in radiopharmacy. Evaluation of optimal anchor groups

International Nuclear Information System (INIS)

Alberto, R.; Schibli, R.; Egli, A.; Schaffland, A.; Rattat, D.; Mueller, J.; Iftimia, M.; Berke, H.; Kaden, T.A.; Abram, U.

1997-01-01

The coordinative properties of the '[fac-M(CO) 3 ] + ' moiety (M= 188 Re, Re, 99 Tc and 99m Tc) have been investigated in water and organic solvents in order to evaluate the anchor group attached to antibodies, small peptides and biologically active molecules. The preparation of [M(OH 2 ) 3 (CO) 3 ] + has been improved in a way that this complex can be prepared from a Kit formulation. The '[fac-M(CO) 3 ] + ' has been transformed to the '[fac-M(NO)(CO) 2 ] 2+ ' moiety to achieve higher direct labelling yields and faster incorporation kinetics. (author) 5 figs

Design Analysis and Observed Performance of a Tieback Anchored Pile Wall in Sand

Directory of Open Access Journals (Sweden)

Jian-Yong Han

2017-01-01

Full Text Available This paper aims to study the design process and service performance of a deep excavation supported by tieback anchored pile walls. The design procedure and design approaches for deep excavation in China are described. Based on the excavation case history for Shenyang, China, design results obtained using the elastic method and the finite element method (FEM are compared and analyzed. Special emphasis is given to the analysis of horizontal wall deformations, internal forces in the wall, earth pressures on the wall, ground surface settlements, and stabilities of the excavation. The similarities and differences between the Chinese code (JGJ 120-2012 and the European code (EN 1997-1 for the design of geotechnical structures are presented based on a design example. Through the comparison, it is indicated that the Chinese code focuses on the design result, while the European code focuses on the design process. The crucial construction methods for reducing construction risk based on the excavation case history are described. The mechanical behaviors of the excavation retained by an anchored pile wall were investigated by analyzing observed field cases. The results provide good, practical guidelines for the design and construction of a tieback anchored pile wall retained excavation in sandy soil.

78 FR 45104 - Model Manufactured Home Installation Standards: Ground Anchor Installations

Science.gov (United States)

2013-07-26

... anchor capacity. In granular soils, large lateral movements may produce failure planes that can reduce..., Consumer protection, Intergovernmental relations, Manufactured homes, Reporting and recordkeeping... relative to the plane of the ground surface and shall be permitted to be rounded to the nearest 5-degree...

Bearing Capacity Analyses for the Great Belt East Bridge Anchor Blocks

DEFF Research Database (Denmark)

Sørensen, Carsten Steen; Clausen, Carl J. Frimann; Andersen, Henrik

1993-01-01

This paper presents a comparison between different methods of bearing capacity analyses: Upper Bound Method. Limit Equilibrium Analysis and Finite Element Analysis. For the Great Belt East Bridge anchor blocks it was concluded that these methods of calculation agree within 5%. However, for cases ...

Spatial Rearrangement and Mobility Heterogeneity of an Anionic Lipid Monolayer Induced by the Anchoring of Cationic Semiflexible Polymer Chains

Directory of Open Access Journals (Sweden)

Xiaozheng Duan

2016-06-01

Full Text Available We use Monte Carlo simulations to investigate the interactions between cationic semiflexible polymer chains and a model fluid lipid monolayer composed of charge-neutral phosphatidyl-choline (PC, tetravalent anionic phosphatidylinositol 4,5-bisphosphate (PIP2, and univalent anionic phosphatidylserine (PS lipids. In particular, we explore how chain rigidity and polymer concentration influence the spatial rearrangement and mobility heterogeneity of the monolayer under the conditions where the cationic polymers anchor on the monolayer. We find that the anchored cationic polymers only sequester the tetravalent PIP2 lipids at low polymer concentrations, where the interaction strength between the polymers and the monolayer exhibits a non-monotonic dependence on the degree of chain rigidity. Specifically, maximal anchoring occurs at low polymer concentrations, when the polymer chains have an intermediate degree of rigidity, for which the PIP2 clustering becomes most enhanced and the mobility of the polymer/PIP2 complexes becomes most reduced. On the other hand, at sufficiently high polymer concentrations, the anchoring strength decreases monotonically as the chains stiffen—a result that arises from the pronounced competitions among polymer chains. In this case, the flexible polymers can confine all PIP2 lipids and further sequester the univalent PS lipids, whereas the stiffer polymers tend to partially dissociate from the monolayer and only sequester smaller PIP2 clusters with greater mobilities. We further illustrate that the mobility gradient of the single PIP2 lipids in the sequestered clusters is sensitively modulated by the cooperative effects between anchored segments of the polymers with different rigidities. Our work thus demonstrates that the rigidity and concentration of anchored polymers are both important parameters for tuning the regulation of anionic lipids.

Analytical Model for Hook Anchor Pull-Out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, Jens Peder; Adamsen, Peter

1995-01-01

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Analytical Model for Hook Anchor Pull-out

DEFF Research Database (Denmark)

Brincker, Rune; Ulfkjær, J. P.; Adamsen, P.

A simple analytical model for the pull-out of a hook anchor is presented. The model is based on a simplified version of the fictitious crack model. It is assumed that the fracture process is the pull-off of a cone shaped concrete part, simplifying the problem by assuming pure rigid body motions...... allowing elastic deformations only in a layer between the pull-out cone and the concrete base. The derived model is in good agreement with experimental results, it predicts size effects and the model parameters found by calibration of the model on experimental data are in good agreement with what should...

Ru-bis(pyridine)pyrazolate (bpp)-Based Water-Oxidation Catalysts Anchored on TiO2: The Importance of the Nature and Position of the Anchoring Group.

Science.gov (United States)

Francàs, Laia; Richmond, Craig; Garrido-Barros, Pablo; Planas, Nora; Roeser, Stephan; Benet-Buchholz, Jordi; Escriche, Lluís; Sala, Xavier; Llobet, Antoni

2016-04-04

Three distinct functionalisation strategies have been applied to the in,in-[{Ru(II)(trpy)}2(μ-bpp)(H2O)2](3+) (trpy=2,2':6',2''-terpyridine, bpp=bis(pyridine)pyrazolate) water-oxidation catalyst framework to form new derivatives that can adsorb onto titania substrates. Modifications included the addition of sulfonate, carboxylate, and phosphonate anchoring groups to the terpyridine and bis(pyridyl)pyrazolate ligands. The complexes were characterised in solution by using 1D NMR, 2D NMR, and UV/Vis spectroscopic analysis and electrochemical techniques. The complexes were then anchored on TiO2-coated fluorinated tin oxide (FTO) films, and the reactivity of these new materials as water-oxidation catalysts was tested electrochemically through controlled-potential electrolysis (CPE) with oxygen evolution detected by headspace analysis with a Clark electrode. The results obtained highlight the importance of the catalyst orientation with respect to the titania surface in regard to its capacity to catalytically oxidize water to dioxygen. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrophilic Cucurbit[7]uril-Pseudorotaxane-Anchored-Monolayer-Protected Gold Nanorods

Science.gov (United States)

2013-03-20

FULL PAPER DOI:10.1002/ejic.201300010 Hydrophilic Cucurbit[7]uril-Pseudorotaxane-Anchored- Monolayer-Protected Gold Nanorods Xiang Ma,[a] Yuhua Xue... Cao , Q. Wang, H. Tian, Chem. Commun. 2011, 47, 3559–3561. [8] a) I. Hwang, K. Baek, M. Jung, Y. Kim, K. M. Park, D. W. Lee, N. Selvapalam, K. Kim, J. Am

Memory for Dialogue: Recalling an Anchor through Talk and Response.

Science.gov (United States)

Beaver, Pam

This paper reports on a project involving student recall of the dialogue in a movie and retention of the "anchor," which in this case refers to a videotape recording of "To Kill a Mockingbird." The project looked at how students retained knowledge over a few days and what kind of activities resulted from expertise with an…

Binding equilibrium and kinetics of membrane-anchored receptors and ligands in cell adhesion: Insights from computational model systems and theory

Science.gov (United States)

Weikl, Thomas R.; Hu, Jinglei; Xu, Guang-Kui; Lipowsky, Reinhard

2016-01-01

ABSTRACT The adhesion of cell membranes is mediated by the binding of membrane-anchored receptor and ligand proteins. In this article, we review recent results from simulations and theory that lead to novel insights on how the binding equilibrium and kinetics of these proteins is affected by the membranes and by the membrane anchoring and molecular properties of the proteins. Simulations and theory both indicate that the binding equilibrium constant K2D and the on- and off-rate constants of anchored receptors and ligands in their 2-dimensional (2D) membrane environment strongly depend on the membrane roughness from thermally excited shape fluctuations on nanoscales. Recent theory corroborated by simulations provides a general relation between K2D and the binding constant K3D of soluble variants of the receptors and ligands that lack the membrane anchors and are free to diffuse in 3 dimensions (3D). PMID:27294442

Germ Plasm Anchoring Is a Dynamic State that Requires Persistent Trafficking

Directory of Open Access Journals (Sweden)

Kristina S. Sinsimer

2013-12-01

Full Text Available Localized cytoplasmic determinants packaged as ribonucleoprotein (RNP particles direct embryonic patterning and cell fate specification in a wide range of organisms. Once established, the asymmetric distributions of such RNP particles must be maintained, often over considerable developmental time. A striking example is the Drosophila germ plasm, which contains RNP particles whose localization to the posterior of the egg during oogenesis results in their asymmetric inheritance and segregation of germline from somatic fates in the embryo. Although actin-based anchoring mechanisms have been implicated, high-resolution live imaging revealed persistent trafficking of germ plasm RNP particles at the posterior cortex of the Drosophila oocyte. This motility relies on cortical microtubules, is mediated by kinesin and dynein motors, and requires coordination between the microtubule and actin cytoskeletons. Finally, we show that RNP particle motility is required for long-term germ plasm retention. We propose that anchoring is a dynamic state that renders asymmetries robust to developmental time and environmental perturbations.

Technical note: Endoscopic resection of a dermoid cyst anchored to the anterior optic chiasm

Directory of Open Access Journals (Sweden)

Yuichiro Yoneoka, MD, PhD

2014-06-01

Conclusion: To the best of our knowledge, ours is the only case of a dermoid cyst anchored to the anterior optic chiasma, which was visually confirmed under endoscopic observation. After surgery, the patient presented a transient impairment of the visual field, which was not evident at four month follow-up. It will contribute to a similar case, in which surgeons hesitate to make an incision in the optic chiasm. A subtotal excision should be considered in cases of dermoid cysts anchored to the anterior optic chiasm, because all the previously reported cases of suprasellar dermoid cysts are young people or those who have a relatively long life expectancy.

Anchoring tick salivary anti-complement proteins IRAC I and IRAC II to membrane increases their immunogenicity.

Science.gov (United States)

Gillet, Laurent; Schroeder, Hélène; Mast, Jan; Thirion, Muriel; Renauld, Jean-Christophe; Dewals, Benjamin; Vanderplasschen, Alain

2009-01-01

Tick salivary proteins are promising targets for the development of anti-tick vaccines. Recently, we described two paralogous anti-complement proteins, called Ixodes ricinus anti-complement (IRAC) proteins I and II, that are co-expressed in tick I. ricinus salivary glands. However, our previous attempts to immunize rabbits against IRAC via infection with recombinant Bovine herpesvirus 4 (BoHV-4) vectors invariably failed although both recombinants expressed high levels of functional IRAC proteins in vitro. As IRAC are soluble monovalent antigens, one of the possible explanations is that monovalent ligation of the B-cell receptor induces receptor activation but fails to promote antigen presentation, a phenomenon that is thought to induce a state of B-cell tolerance. In the present study, we tried to increase IRAC immunogenicity by expressing them as oligovalent antigens. To this end, IRAC were fused to membrane anchors and BoHV-4 vectors expressing these recombinant forms were produced. The immunization potentials of recombinant viruses expressing either secreted or transmembrane IRAC proteins were then compared. While the former did not induce a detectable immune response against IRAC, the latter led to high titres of anti-IRAC antibodies that only marginally affected tick blood feeding. All together, the data presented in this study demonstrate that the immunogenicity of a soluble antigen can be greatly improved by anchoring it in membrane.

Avulsion Fracture of the Calcaneus Treated With a Soft Anchor Bridge and Lag Screw Technique: A Report of Two Cases.

Science.gov (United States)

Yoshida, Kazushige; Kasama, Kentaro; Akahane, Tsutomu

2016-01-01

The displaced extra-articular avulsion fracture of the calcaneus has been classified as a Böhler type 1c calcaneal fracture, and most cases will require surgical repair. In the present report, we describe 2 patients in whom we performed the soft anchor bridge technique using single loaded suture anchors with lag screws for the repair of Böhler type 1c avulsion fractures of the calcaneus. In one of these patients, clinically relevant osteoporosis complicated the injury. In both cases, bone union was achieved, and by 1.5 months after surgery satisfactory recovery was observed. To our knowledge, the soft anchor bridge technique was first used for the treatment of rotator cuff tears, and the greatest merit of this technique is the ability to generate vertical compression force to the pulled out rotator cuff through the use of knotting sutures. In recent years, the soft anchor bridge technique using 4 suture anchors has also been used for fractures of the greater tuberosity of the humerus, an injury that poses operative difficulties similar to those encountered with an avulsion fracture of the calcaneus owing to the traction force of the rotator cuff and relative weakness of adjacent bone. The outcomes of our patients suggest that the soft anchor bridge technique combined with adjunct lag screws is useful in the fixation of avulsion fractures of the calcaneus. In addition, the result in the elderly patient indicates the possibility of using this technique for patients with osteoporosis. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Quadriceps tendon rupture: a biomechanical comparison of transosseous equivalent double-row suture anchor versus transosseous tunnel repair.

Science.gov (United States)

Hart, Nathan D; Wallace, Matthew K; Scovell, J Field; Krupp, Ryan J; Cook, Chad; Wyland, Douglas J

2012-09-01

Quadriceps rupture off the patella is traditionally repaired by a transosseous tunnel technique, although a single-row suture anchor repair has recently been described. This study biomechanically tested a new transosseous equivalent (TE) double-row suture anchor technique compared with the transosseous repair for quadriceps repair. After simulated quadriceps-patella avulsion in 10 matched cadaveric knees, repairs were completed by either a three tunnel transosseous (TT = 5) or a TE suture anchor (TE = 5) technique. Double-row repairs were done using two 5.5 Bio-Corkscrew FT (fully threaded) (Arthrex, Inc., Naples, FL, USA) and two 3.5 Bio-PushLock anchors (Arthrex, Inc., Naples, FL, USA) with all 10 repairs done with #2 FiberWire suture (Arthrex, Inc., Naples, FL). Cyclic testing from 50 to 250 N for 250 cycles and pull to failure load (1 mm/s) were undertaken. Gap formation and ultimate tensile load (N) were recorded and stiffness data (N/mm) were calculated. Statistical analysis was performed using a Mann-Whitney U test and survival characteristics examined with Kaplan-Meier test. No significant difference was found between the TE and TT groups in stiffness (TE = 134 +/- 15 N/mm, TT = 132 +/- 26 N/mm, p = 0.28). The TE group had significantly less ultimate tensile load (N) compared with the TT group (TE = 447 +/- 86 N, TT = 591 +/- 84 N, p = 0.04), with all failures occurring at the suture eyelets. Although both quadriceps repairs were sufficiently strong, the transosseous repairs were stronger than the TE suture anchor repairs. The repair stiffness and gap formation were similar between the groups.

Bone-anchored hearing aids in conductive and mixed hearing losses: why do patients reject them?

Science.gov (United States)

Siau, Richard T K; Dhillon, Baljeet; Siau, Derrick; Green, Kevin M J

2016-10-01

This study aimed to report the bone-anchored hearing aid uptake rate and the reasons for their rejection by patients with conductive and mixed hearing losses. A retrospective review was performed of 113 consecutive patients with unilateral or bilateral conductive or mixed hearing loss referred to the Greater Manchester bone-anchored hearing aid (BAHA) programme between September 2008 and August 2011. 98 (86.7 %) patients were deemed audiologically suitable for BAHA implantation. Of these, 38 (38.8 %) had BAHA implanted; 60 (61.2 %) patients declined. Of those who declined, 27 (45 %) cited anxiety over surgery, 18 (30 %) cited cosmetic reasons, 16 (26.7 %) perceived limited benefit from the device and six (10 %) preferred conventional hearing aids. Our study highlights a 38.8 % BAHA uptake rate in audiologically suitable patients. The main reasons cited for rejection of BAHA were anxiety over surgery and cosmetic concerns. It is important that clinicians address these early during consultation with prospective BAHA recipients and avoid rushing to implant these patients with a bone-anchored hearing aid.

Fluorine-doped SnO2 nanoparticles anchored on reduced graphene oxide as a high-performance lithium ion battery anode

Science.gov (United States)

Cui, Dongming; Zheng, Zhong; Peng, Xue; Li, Teng; Sun, Tingting; Yuan, Liangjie

2017-09-01

The composite of fluorine-doped SnO2 anchored on reduced graphene oxide (F-SnO2/rGO) has been synthesized through a hydrothermal method. F-SnO2 particles with average size of 8 nm were uniformly anchored on the surfaces of rGO sheets and the resulting composite had a high loading of F-SnO2 (ca. 90%). Benefiting from the remarkably improved electrical conductivity and Li-ion diffusion in the electrode by F doping and rGO incorporation, the composite material exhibited high reversible capacity, excellent long-term cycling stability and superior rate capability. The electrode delivered a large reversible capacity of 1037 mAh g-1 after 150 cycles at 100 mA g-1 and high rate capacities of 860 and 770 mAh g-1 at 1 and 2 A g-1, respectively. Moreover, the electrode could maintain a high reversible capacities of 733 mAh g-1 even after 250 cycles at 500 mA g-1. The outstanding electrochemical performance of the as-synthesized composite make it a promising anode material for high-energy lithium ion batteries.

Organisation, ‘anchoring’ of knowledge, and innovation in the construction industry

DEFF Research Database (Denmark)

Drejer, Ina; Vinding, Anker Lund

2004-01-01

explanation for the relatively poor innovation performance of the industry. Using survey data from the Danish construction industry the paper investigates the importance of learning and ?anchoring? of project specific knowledge within the firms for facilitating engagement in innovative activities...... at the firm level. The data refer to the overall Danish construction industry, as well as a specific region, North Jutland, which is relatively specialised in construction. By using latent class and regression analysis the results show that firms, which to a high extent make use of partnering and other...... interorganisational features, combined with internal product and process evaluation and knowledge diffusion, are more likely to engage in innovative activities than firms that make less use of what we label ?knowledge anchoring mechanisms?. This indicates that there are ways for firms to compensate for the problems...

Work values and career anchors: the perspective of students of higher education in classroom methods and distance

Directory of Open Access Journals (Sweden)

Tais de Andrade

2018-01-01

Full Text Available This study takes into account the factors that interfere with career decisions from the internal demands of individuals, represented by the work values. Investigated university students’ perspective on work values and career anchors. For this, we used a survey along the 958 undergraduate students of face and distance higher education institutions in the interior of Rio Grande do Sul. The data collection instrument was developed from the Work Values Scale Revised developed by Porto and Pilati (2010 and the Inventory of Career Anchors proposed by Schein (1993; 1996. As for the results, there were significant differences between the perceptions of the two methods of teaching, but the hierarchy assigned to the values and anchors in both was similar, which shows certain pattern of agreement as to the perception of importance attached to each dimension studied.

The RIO approach : Design and anchoring of sustainable animal husbandry systems

NARCIS (Netherlands)

Elzen, Boelie; Bos, Bram

2016-01-01

This paper discusses an approach to develop new 'integrally sustainable' animal production systems and stimulate their uptake in practice. It consists of a design approach called RIO, and a set of 'anchoring' activities to stimulate their uptake in niches and in the regime. In the period 2001-2015

Coupled thermo-fluid stress analysis of Kambara Reactor with various anchors in the stirring of molten iron at extremely high temperatures

International Nuclear Information System (INIS)

Huang, De-Shau; Huang, Feng-Chi

2014-01-01

Kambara Reactors (KR) are commonly used to reduce sulfur content in steel making, achieving efficiency levels exceeding 85% at 1300 °C. Unfortunately, the operational lifespan of the KR impeller is somewhat limited due to fracturing of the refractory material via thermal shock, resulting in the penetration of molten iron into the inner core. Few studies have investigated the coupled thermo-fluid stress of KR impellers at extremely high temperatures. This study employed CFX and FEM to simulate and analyze the molten iron and the resulting thermal stress imposed on the KR impeller. Simulation results including flow field, temperature, and thermal stress under extremely high temperatures are in strong agreement with empirical data. V-type anchors for the KR impeller outperformed Y-type anchors. - Highlights: • A thermo-fluid coupling approach is proposed to analyze the thermal stress. • The temperature and stress of the impeller are 790 °C and 744 MPa at the final stage. • The highest temperatures occur at the tip of anchors, which causes material crack. • The thermal stress in impellers with Y-type anchors is greater than V-type anchors

A prospective outcome and cost-effectiveness comparison between two ligament reattachment techniques using suture anchors for chronic ankle instability.

Science.gov (United States)

Cho, Byung-Ki; Kim, Yong-Min; Park, Kyoung-Jin; Park, Ji-Kang; Kim, Do-Kyoon

2015-02-01

There are various ligament reattachment techniques for the modified Brostrom procedure. There have been few comparative studies on recently developed techniques. This prospective study was performed to compare the functional outcomes of 2 different ligament reattachment techniques using suture anchors. We furthermore evaluated the cost-effectiveness of the suture bridge technique. Forty-five amateur athletes under 30 years of age were followed for more than 2 years. Twenty-four procedures with the suture anchor technique and 21 procedures with the suture bridge technique were performed by one surgeon. The functional evaluation consisted of the American Orthopaedic Foot & Ankle Society (AOFAS) score, Foot and Ankle Outcome Score (FAOS), Karlsson score, Sefton grading system, and the period to return to various forms of exercise (jogging, spurt running, jumping, one leg standing for >1 minute, walking on uneven ground, and going down stairs). Measurement of talar tilt angle and anterior talar translation was obtained from stress radiographs to evaluate mechanical stability. There were no significant differences on AOFAS score, FAOS, Karlsson score, Sefton grade, and stress radiographs. There were no significant differences on the return to exercises, except for jumping. As the most common complication, there were 3 cases of skin irritation by suture materials in the suture anchor group and 2 cases of intraoperative breakage of the suture anchor in suture bridge group. Both ligament reattachment techniques using suture anchors showed similar functional outcomes. Considering the additional medical expenses incurred by more suture anchors, the modified Brostrom procedure using the suture bridge technique had low cost-effectiveness. Proper indication and clinical usefulness of suture bridge technique for chronic ankle instability will be addressed in further studies. Level II, prospective comparative study. © The Author(s) 2014.

Comparison of optical see-through head-mounted displays for surgical interventions with object-anchored 2D-display.

Science.gov (United States)

Qian, Long; Barthel, Alexander; Johnson, Alex; Osgood, Greg; Kazanzides, Peter; Navab, Nassir; Fuerst, Bernhard

2017-06-01

Optical see-through head-mounted displays (OST-HMD) feature an unhindered and instantaneous view of the surgery site and can enable a mixed reality experience for surgeons during procedures. In this paper, we present a systematic approach to identify the criteria for evaluation of OST-HMD technologies for specific clinical scenarios, which benefit from using an object-anchored 2D-display visualizing medical information. Criteria for evaluating the performance of OST-HMDs for visualization of medical information and its usage are identified and proposed. These include text readability, contrast perception, task load, frame rate, and system lag. We choose to compare three commercially available OST-HMDs, which are representatives of currently available head-mounted display technologies. A multi-user study and an offline experiment are conducted to evaluate their performance. Statistical analysis demonstrates that Microsoft HoloLens performs best among the three tested OST-HMDs, in terms of contrast perception, task load, and frame rate, while ODG R-7 offers similar text readability. The integration of indoor localization and fiducial tracking on the HoloLens provides significantly less system lag in a relatively motionless scenario. With ever more OST-HMDs appearing on the market, the proposed criteria could be used in the evaluation of their suitability for mixed reality surgical intervention. Currently, Microsoft HoloLens may be more suitable than ODG R-7 and Epson Moverio BT-200 for clinical usability in terms of the evaluated criteria. To the best of our knowledge, this is the first paper that presents a methodology and conducts experiments to evaluate and compare OST-HMDs for their use as object-anchored 2D-display during interventions.

Pipe supports and anchors - LMFBR applications

International Nuclear Information System (INIS)

Anderson, M.J.

1983-06-01

Pipe design and support design can not be treated as separate disciplines. A coordinated design approach is required if LMFBR pipe system adequacy is to be achieved at a reasonable cost. It is particularly important that system designers understand and consider those factors which influence support train flexibility and thus the pipe system dynamic stress levels. The system approach must not stop with the design phase but should continue thru the erection and acceptance test procedures. The factors that should be considered in the design of LMFBR pipe supports and anchors are described. The various pipe support train elements are described together with guidance on analysis, design and application aspects. Post erection acceptance and verification test procedures are then discussed

Medical Image Visual Appearance Improvement Using Bihistogram Bezier Curve Contrast Enhancement: Data from the Osteoarthritis Initiative

Science.gov (United States)

Gan, Hong-Seng; Swee, Tan Tian; Abdul Karim, Ahmad Helmy; Sayuti, Khairil Amir; Abdul Kadir, Mohammed Rafiq; Tham, Weng-Kit; Wong, Liang-Xuan; Chaudhary, Kashif T.; Yupapin, Preecha P.

2014-01-01

Well-defined image can assist user to identify region of interest during segmentation. However, complex medical image is usually characterized by poor tissue contrast and low background luminance. The contrast improvement can lift image visual quality, but the fundamental contrast enhancement methods often overlook the sudden jump problem. In this work, the proposed bihistogram Bezier curve contrast enhancement introduces the concept of “adequate contrast enhancement” to overcome sudden jump problem in knee magnetic resonance image. Since every image produces its own intensity distribution, the adequate contrast enhancement checks on the image's maximum intensity distortion and uses intensity discrepancy reduction to generate Bezier transform curve. The proposed method improves tissue contrast and preserves pertinent knee features without compromising natural image appearance. Besides, statistical results from Fisher's Least Significant Difference test and the Duncan test have consistently indicated that the proposed method outperforms fundamental contrast enhancement methods to exalt image visual quality. As the study is limited to relatively small image database, future works will include a larger dataset with osteoarthritic images to assess the clinical effectiveness of the proposed method to facilitate the image inspection. PMID:24977191

Medical Image Visual Appearance Improvement Using Bihistogram Bezier Curve Contrast Enhancement: Data from the Osteoarthritis Initiative

Directory of Open Access Journals (Sweden)

Hong-Seng Gan

2014-01-01

Full Text Available Well-defined image can assist user to identify region of interest during segmentation. However, complex medical image is usually characterized by poor tissue contrast and low background luminance. The contrast improvement can lift image visual quality, but the fundamental contrast enhancement methods often overlook the sudden jump problem. In this work, the proposed bihistogram Bezier curve contrast enhancement introduces the concept of “adequate contrast enhancement” to overcome sudden jump problem in knee magnetic resonance image. Since every image produces its own intensity distribution, the adequate contrast enhancement checks on the image’s maximum intensity distortion and uses intensity discrepancy reduction to generate Bezier transform curve. The proposed method improves tissue contrast and preserves pertinent knee features without compromising natural image appearance. Besides, statistical results from Fisher’s Least Significant Difference test and the Duncan test have consistently indicated that the proposed method outperforms fundamental contrast enhancement methods to exalt image visual quality. As the study is limited to relatively small image database, future works will include a larger dataset with osteoarthritic images to assess the clinical effectiveness of the proposed method to facilitate the image inspection.

Fracture resistance of reattached incisor fragments with mini fibre-reinforced composite anchors.

NARCIS (Netherlands)

Fennis, W.M.M.; Kreulen, C.M.; Wolke, J.G.C.; Fokkinga, W.A.; Machado, C.; Creugers, N.H.J.

2009-01-01

OBJECTIVES: Fractured coronal fragments of incisors can be adhered to the remaining tooth with resin composite, but are prone to failure. This study explores whether mini fibre-reinforced composite (FRC) anchors increase fracture resistance of reattached fragments. METHODS: Forty-five extracted

Laparoscopic sacrocolpopexy with bone anchor fixation: short-term anatomic and functional results.

NARCIS (Netherlands)

Withagen, M.I.J.; Vierhout, M.E.; Mannaerts, G.H.; Weiden, R.M.F. van der

2012-01-01

INTRODUCTION AND HYPOTHESIS: The aim of this study was to evaluate short-term anatomic and functional outcomes and safety of laparoscopic sacrocolpopexy with bone anchor fixation. METHODS: A prospective cohort study of women undergoing laparoscopic sacrocolpopexy between 2004 and 2009. Anatomic

Cerebral CT appearances of toxic encephalopathy of tetramine

International Nuclear Information System (INIS)

Zheng Wenlong; Wu Aiqin; Xu Chongyong; Ying Binyu; Hong Ruizhen

2003-01-01

Objective: To investigate the cerebral CT appearances of toxic encephalopathy of tetramine and improve the recognition on this disease. Methods: Four cases of toxic encephalopathy of tetramine were collected and their cerebral CT appearances were retrospectively analyzed. Results: Cerebral CT appearances in acute phase (within 8 days): (1) cerebral edema in different degree. CT abnormalities consisted of cortical hypodensities and complete loss of gray-white matter differentiation. The CT value were in 11-13 HU, and to be watery density in serious case, (2) subarachnoid hemorrhage. It demonstrated the signs of poisoning hypoxic ischemic encephalopathy in chronic phase. Conclusion: The cerebral CT appearances of toxic encephalopathy of tetramine had some character in acute phase and it can predict the serious degree of intoxication, but there was no characteristic findings in chronic phase

Anchor-Free Localization Method for Mobile Targets in Coal Mine Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Xiao Xu

2009-04-01

Full Text Available Severe natural conditions and complex terrain make it difficult to apply precise localization in underground mines. In this paper, an anchor-free localization method for mobile targets is proposed based on non-metric multi-dimensional scaling (Multi-dimensional Scaling: MDS and rank sequence. Firstly, a coal mine wireless sensor network is constructed in underground mines based on the ZigBee technology. Then a non-metric MDS algorithm is imported to estimate the reference nodes’ location. Finally, an improved sequence-based localization algorithm is presented to complete precise localization for mobile targets. The proposed method is tested through simulations with 100 nodes, outdoor experiments with 15 ZigBee physical nodes, and the experiments in the mine gas explosion laboratory with 12 ZigBee nodes. Experimental results show that our method has better localization accuracy and is more robust in underground mines.

Anchor-free localization method for mobile targets in coal mine wireless sensor networks.

Science.gov (United States)

Pei, Zhongmin; Deng, Zhidong; Xu, Shuo; Xu, Xiao

2009-01-01

Severe natural conditions and complex terrain make it difficult to apply precise localization in underground mines. In this paper, an anchor-free localization method for mobile targets is proposed based on non-metric multi-dimensional scaling (Multi-dimensional Scaling: MDS) and rank sequence. Firstly, a coal mine wireless sensor network is constructed in underground mines based on the ZigBee technology. Then a non-metric MDS algorithm is imported to estimate the reference nodes' location. Finally, an improved sequence-based localization algorithm is presented to complete precise localization for mobile targets. The proposed method is tested through simulations with 100 nodes, outdoor experiments with 15 ZigBee physical nodes, and the experiments in the mine gas explosion laboratory with 12 ZigBee nodes. Experimental results show that our method has better localization accuracy and is more robust in underground mines.

The Effect of Listener Experience and Anchors on Judgments of Dysphonia

Science.gov (United States)

Eadie, Tanya L.; Kapsner-Smith, Mara

2011-01-01

Purpose: To determine the effect of auditory anchors on judgments of overall severity (OS) and vocal effort (VE) in dysphonic speech when judgments are made by experienced and inexperienced listeners, and when self-rated by individuals with dysphonia (speaker-listeners). Method: Twenty individuals with dysphonia and 4 normal controls provided…

Decay accelerating factor of complement is anchored to cells by a C-terminal glycolipid

International Nuclear Information System (INIS)

Medof, M.E.; Walter, E.I.; Roberts, W.L.; Haas, R.; Rosenberry, T.L.

1986-01-01

Membrane-associated decay accelerating factor (DAF) of human erythrocytes (E/sup hu/) was analyzed for a C-terminal glycolipid anchoring structure. Automated amino acid analysis of DAF following reductive radiomethylation revealed ethanolamine and glucosamine residues in proportions identical with those present in the E/sup hu/ acetylcholinesterase (AChE) anchor. Cleavage of radiomethylated 70-kilodalton (kDa) DAF with papain released the labeled ethanolamine and glucosamine and generated 61- and 55-kDa DAF products that retained all labeled Lys and labeled N-terminal Asp. Incubation of intact E/sup hu/ with phosphatidylinositol-specific phospholipase C (PI-PLC), which cleaves the anchors in trypanosome membrane form variant surface glycoproteins (mfVSGs) and murine thymocyte Thy-1 antigen, released 15% of the cell-associated DAF antigen. The released 67-kDa PI-PLC DAF derivative retained its ability to decay the classical C3 convertase C4b2a but was unable to membrane-incorporate and displayed physicochemical properties similar to urine DAF, a hydrophilic DAF form that can be isolated for urine. Nitrous acid deamination cleavage of E/sup hu/ DAF at glucosamine following labeling with the lipophilic photoreagent 3-(trifluoromethyl)-3-(m-[ 125 I]iodophenyl)diazirine ([ 125 I]TID) released the [ 125 I]TID label in a parallel fashion as from [ 125 I]TID-labeled AChE. Biosynthetic labeling of HeLa cells with [ 3 H] ethanolamine resulted in rapid 3 H incorporation into both 48-kDa pro-DAF and 72-kDa mature epithelial cell DAF. The findings indicate that DAF and AChE are anchored in E/sup hu/ by the same or a similar glycolipid structure and that, like VSGs, this structure is incorporated into DAF early in DAF biosynthesis prior to processing of pro-DAF in the Golgi

Making a model meaningful to coral reef managers in a developing nation: a case study of overfishing and rock anchoring in Indonesia.

Science.gov (United States)

Maynard, Jeffrey A; Anthony, Kenneth R N; Afatta, Siham; Dahl-Tacconi, Nancy; Hoegh-Guldberg, Ove

2010-10-01

Most of the world's coral reefs line the coasts of developing nations, where impacts from intense and destructive fishing practices form critical conservation issues for managers. Overfishing of herbivorous fishes can cause phase shifts to macroalgal dominance, and fishers' use of rocks as anchors lowers coral cover, giving further competitive advantage to macroalgae. Overfishing and anchoring have been studied extensively, but the role of their interaction in lowering coral reef resilience has not been quantified formally. We analyzed the combined effects of overfishing and rock anchoring on a range of reef habitat types--varying from high coral and low macroalgae cover to low coral and high macroalgae cover--in a marine park in Indonesia. We parameterized a model of coral and algal dynamics with three intensities of anchoring and fishing pressure. Results of the model indicated that damage caused by rock anchoring was equal to or possibly more devastating to coral reefs in the area than the impact of overfishing. This is an important outcome for local managers, who usually have the funds to distribute less-damaging anchors, but normally are unable to patrol regularly and effectively enough to reduce the impact of overfishing. We translated model results into an interactive visual tool that allows managers to explore the benefits of reducing anchoring frequency and fishing pressure. The potential consequences of inaction were made clear: the likelihood that any of the reef habitats will be dominated in the future by macroalgae rather than corals depends on reducing anchoring frequency, fishing pressure, or both. The tool provides a platform for strengthened relationships between managers and conservationists and can facilitate the uptake of recommendations regarding resource allocation and management actions. Conservation efforts for coral reefs in developing nations are likely to benefit from transforming model projections of habitat condition into tools local

High-Performance Modeling and Simulation of Anchoring in Granular Media for NEO Applications

Science.gov (United States)

Quadrelli, Marco B.; Jain, Abhinandan; Negrut, Dan; Mazhar, Hammad

2012-01-01

NASA is interested in designing a spacecraft capable of visiting a near-Earth object (NEO), performing experiments, and then returning safely. Certain periods of this mission would require the spacecraft to remain stationary relative to the NEO, in an environment characterized by very low gravity levels; such situations require an anchoring mechanism that is compact, easy to deploy, and upon mission completion, easy to remove. The design philosophy used in this task relies on the simulation capability of a high-performance multibody dynamics physics engine. On Earth, it is difficult to create low-gravity conditions, and testing in low-gravity environments, whether artificial or in space, can be costly and very difficult to achieve. Through simulation, the effect of gravity can be controlled with great accuracy, making it ideally suited to analyze the problem at hand. Using Chrono::Engine, a simulation pack age capable of utilizing massively parallel Graphic Processing Unit (GPU) hardware, several validation experiments were performed. Modeling of the regolith interaction has been carried out, after which the anchor penetration tests were performed and analyzed. The regolith was modeled by a granular medium composed of very large numbers of convex three-dimensional rigid bodies, subject to microgravity levels and interacting with each other with contact, friction, and cohesional forces. The multibody dynamics simulation approach used for simulating anchors penetrating a soil uses a differential variational inequality (DVI) methodology to solve the contact problem posed as a linear complementarity method (LCP). Implemented within a GPU processing environment, collision detection is greatly accelerated compared to traditional CPU (central processing unit)- based collision detection. Hence, systems of millions of particles interacting with complex dynamic systems can be efficiently analyzed, and design recommendations can be made in a much shorter time. The figure

[PART-KESSLER TECHNIQUE WITH SUTURE ANCHOR IN REPAIR OF SPONTANEOUS Achilles TENDON RUPTURE].

Science.gov (United States)

Qi, Jie; Duan, Liang; Li, Weiwei; Wei, Wenbo

2016-02-01

To summarize the application and experience of repairing spontaneous Achilles tendon rupture by part-Kessler technique with suture anchor. Between January 2011 and December 2013, 31 patients with spontaneous Achilles tendon rupture were treated by part-Kessler technique with suture anchor. Of 31 cases, 23 were male and 8 were female, aged 16-53 years (mean, 38 years). The left side was involved in 15 cases and the right side in 16 cases. The causes of injury included sudden heel pain and walking weakness during sports in 22 cases; no surefooted down-stairs, slip, and carrying heavy loads in 9 cases. The distance from broken site to the calcaneus adhension of Achilles tendon was 3-6 cm (mean, 4.2 cm). The time from injury to operation was 7 hours to 4 days (mean, 36.8 hours). All incisions healed by first intention without nerve injury or adhering with skin. The patients were followed up 6-24 months (mean, 15 months). All patients could complete 25 times heel raising without difficulty at 6 months after operation. No Achilles tendon rupture occurred again during follow-up. At 6 months after operation, the range of motion of the ankle joint in dorsiflexion and plantar flexion showed no significant difference between normal and affected sides (t=0.648, P=0.525; t=0.524, P=0.605). The circumference of the affected leg was significantly smaller than that of normal leg at 6 months after operation (t=2.074, P=0.041), but no significant difference was found between affected and normal sides at 12 months after operation (t=0.905, P=0.426). The American Orthopedic Foot and Ankle Society (AOFAS) scores at 6, 12, 18, and 24 months after operation were significantly higher than preoperative score (P0.05). Repairing spontaneous Achilles tendon rupture by part-Kessler technique with suture anchor can supply strong strain and decrease the shear forces of suture. So part-Kessler technique with suture anchor is successful in repairing spontaneous Achilles tendon rupture.

Formation and properties of surface-anchored polymer assemblies with tunable physico-chemical characteristics

Science.gov (United States)

Wu, Tao

We describe two new methodologies leading to the formation of novel surface-anchored polymer assemblies on solid substrates. While the main goal is to understand the fundamentals pertaining to the preparation and properties of the surface-bound polymer assemblies (including neutral and chargeable polymers), several examples also are mentioned throughout the Thesis that point out to practical applications of such structures. The first method is based on generating assemblies comprising anchored polymers with a gradual variation of grafting densities on solid substrates. These structures are prepared by first covering the substrate with a molecular gradient of the polymerization initiator, followed by polymerization from these substrate-bound initiator centers ("grafting from"). We apply this technique to prepare grafting density gradients of poly(acryl amide) (PAAm) and poly(acrylic acid) (PAA) on silica-covered substrates. We show that using the grafting density gradient geometry, the characteristics of surface-anchored polymers in both the low grafting density ("mushroom") regime as well as the high grafting density ("brush") regime can be accessed conveniently on a single sample. We use a battery of experimental methods, including Fourier transform infrared spectroscopy (FTIR), Near-edge absorption fine structure spectroscopy (NEXAFS), contact angle, ellipsometry, to study the characteristics of the surface-bound polymer layers. We also probe the scaling laws of neutral polymer as a function of grafting density, and for weak polyelectrolyte, in addition to the grafting density, we study the affect of solution ionic strength and pH values. In the second novel method, which we coined as "mechanically assisted polymer assembly" (MAPA), we form surface anchored polymers by "grafting from" polymerization initiators deposited on elastic surfaces that have been previously extended uniaxially by a certain length increment, Deltax. Upon releasing the strain in the

Starting point anchoring effects in choice experiments

DEFF Research Database (Denmark)

Ladenburg, Jacob; Olsen, Søren Bøye

of preferences in Choice Experiments resembles the Dichotomous Choice format, there is reason to suspect that Choice Experiments are equally vulnerable to anchoring bias. Employing different sets of price levels in a so-called Instruction Choice Set presented prior to the actual choice sets, the present study...... subjectivity in the present study is gender dependent, pointing towards, that female respondents are prone to be affected by the price levels employed. Male respondents, on the other hand, are not sensitive towards these prices levels. Overall, this implicates that female respondents, when employing a low......-priced Instruction Choice Set, tend to express lower willingness-to-pay than when higher prices are employed....

Codend selectivity in a commercial Danish anchor seine

DEFF Research Database (Denmark)

Noack, Thomas; Frandsen, Rikke; Krag, Ludvig Ahm

2017-01-01

Danish seining (or anchor seining) is a fishing technique that is gaining increasing attention because itis considered to be a fuel-efficient fishing method with low environmental impact. However, scientificdocumentation of the selectivity characteristics of Danish seines is lacking, and the gear....... The estimatedselectivity curve of dab indicated, contrary to cod and plaice, low retention of individuals below MLS.Confidence limits for larger length classes of cod and red gurnard were relatively wide. For plaice, theestimated selection factor, which is the length with 50% retention divided by mesh size...

Investigation of edge plasmas in the anchor cell region of GAMMA 10

International Nuclear Information System (INIS)

Islam, Khairul; Nakashima, Yousuke; Yatsu, Kiyoshi

2000-01-01

The first results of Langmuir probe measurements at the outer transition region of the anchor cell of GAMMA 10 are given. A probe current asymmetry in vertical direction is found in this region. It is also found that the asymmetry of probe current increases in outward direction and the direction of the asymmetry is independent on movable limiter position. A relation of the plasma asymmetry with the main magnetic field configuration is investigated. Plasma flow through the non-asymmetric magnetic field configuration region is thought to be the source of plasma asymmetry in this region, i.e., ∇B and curvature drifts are responsible for the asymmetry. Possibility of cold plasma formation in the anchor cell region is obtained during plug electron cyclotron resonance heating (ECRH) and can be explained with the desorption of particles due to the collision of the drifted out particles with the wall. (author)

Electromagnetic interference of bone-anchored hearing aids by cellular phones.

Science.gov (United States)

Kompis, M; Negri, S; Häusler, R

2000-10-01

We report a case of electromagnetic interference between a bone-anchored hearing aid (BAHA) and a cellular phone. A 54-year-old women was successfully treated for severe mixed conductive and sensorineural hearing loss with a BAHA. Five years after implantation, the patient experienced a sudden feeling of dizziness, accompanied by a loud buzzing sound and by a sensation of head pressure while examining a digital mobile phone. During a subsequent experiment, the buzzing sound could be reproduced and was identified as electromagnetic interference between the BAHA and digital cellular phones. Seventeen adult BAHA users from our clinic participated in a subsequent survey. Of the 13 patients with some experience of digital cellular phones, 11 reported hearing annoying noises elicited by these devices. However, no other sensation, such as dizziness, was described. Owing to the increasing number of users of both hearing aids and cellular phones, the incidence of electromagnetic interference must be expected to increase as well. Although to date there is no evidence that such interference may be harmful or dangerous to users of conventional or bone-anchored hearing aids, unexpected interference can be a frightening experience.

Predicting the Pullout Capacity of Small Ground Anchors Using Nonlinear Integrated Computing Techniques

Directory of Open Access Journals (Sweden)

Mosbeh R. Kaloop

2017-01-01

Full Text Available This study investigates predicting the pullout capacity of small ground anchors using nonlinear computing techniques. The input-output prediction model for the nonlinear Hammerstein-Wiener (NHW and delay inputs for the adaptive neurofuzzy inference system (DANFIS are developed and utilized to predict the pullout capacity. The results of the developed models are compared with previous studies that used artificial neural networks and least square support vector machine techniques for the same case study. The in situ data collection and statistical performances are used to evaluate the models performance. Results show that the developed models enhance the precision of predicting the pullout capacity when compared with previous studies. Also, the DANFIS model performance is proven to be better than other models used to detect the pullout capacity of ground anchors.

Lipid Binding of the Amphipathic Helix Serving as Membrane Anchor of Pestivirus Glycoprotein Erns.

Science.gov (United States)

Aberle, Daniel; Oetter, Kay-Marcus; Meyers, Gregor

2015-01-01

Pestiviruses express a peculiar protein named Erns representing envelope glycoprotein and RNase, which is important for control of the innate immune response and persistent infection. The latter functions are connected with secretion of a certain amount of Erns from the infected cell. Retention/secretion of Erns is most likely controlled by its unusual membrane anchor, a long amphipathic helix attached in plane to the membrane. Here we present results of experiments conducted with a lipid vesicle sedimentation assay able to separate lipid-bound from unbound protein dissolved in the water phase. Using this technique we show that a protein composed of tag sequences and the carboxyterminal 65 residues of Erns binds specifically to membrane vesicles with a clear preference for compositions containing negatively charged lipids. Mutations disturbing the helical folding and/or amphipathic character of the anchor as well as diverse truncations and exchange of amino acids important for intracellular retention of Erns had no or only small effects on the proteins membrane binding. This result contrasts the dramatically increased secretion rates observed for Erns proteins with equivalent mutations within cells. Accordingly, the ratio of secreted versus cell retained Erns is not determined by the lipid affinity of the membrane anchor.

Lipid Binding of the Amphipathic Helix Serving as Membrane Anchor of Pestivirus Glycoprotein Erns.

Directory of Open Access Journals (Sweden)

Daniel Aberle

Full Text Available Pestiviruses express a peculiar protein named Erns representing envelope glycoprotein and RNase, which is important for control of the innate immune response and persistent infection. The latter functions are connected with secretion of a certain amount of Erns from the infected cell. Retention/secretion of Erns is most likely controlled by its unusual membrane anchor, a long amphipathic helix attached in plane to the membrane. Here we present results of experiments conducted with a lipid vesicle sedimentation assay able to separate lipid-bound from unbound protein dissolved in the water phase. Using this technique we show that a protein composed of tag sequences and the carboxyterminal 65 residues of Erns binds specifically to membrane vesicles with a clear preference for compositions containing negatively charged lipids. Mutations disturbing the helical folding and/or amphipathic character of the anchor as well as diverse truncations and exchange of amino acids important for intracellular retention of Erns had no or only small effects on the proteins membrane binding. This result contrasts the dramatically increased secretion rates observed for Erns proteins with equivalent mutations within cells. Accordingly, the ratio of secreted versus cell retained Erns is not determined by the lipid affinity of the membrane anchor.

Anatomical principles for minimally invasive reconstruction of the acromioclavicular joint with anchors.

Science.gov (United States)

Xiong, Chuanzhi; Lu, Yaojia; Wang, Qiang; Chen, Gang; Hu, Hansheng; Lu, Zhihua

2016-11-01

The aim of this study was to evaluate the outcome of a minimally invasive surgical technique for the treatment of patients with acromioclavicular joint dislocation. Sixteen patients with complete acromioclavicular joint dislocation were enrolled in this study. All patients were asked to follow the less active rehabilitation protocol post-operatively. Computed tomography with 3-D reconstruction of the injured shoulder was performed on each patient post operatively for the assessment of the accuracy of the suture anchor placement in the coracoid process and the reduction of the acromioclavicular joint. Radiographs of Zanca view and axillary view of both shoulders were taken for evaluating the maintenance of the acromioclavicular joint reduction at each follow-up visit. The Constant shoulder score was used for function assessment at the final follow-up. Twenty seven of the 32 anchors implanted in the coracoid process met the criteria of good position. One patient developed complete loss of reduction and another had partial loss of reduction in the anteroposterior plane. For the other 14 patients, the mean Constant score was 90 (range, 82-95). For the patients with partial and complete loss of reduction, the Constant score were 92 and 76 respectively. All of them got nearly normal range of motion of the shoulders and restored to pre-operative life and works. With this minimally invasive approach and limited exposure of the coracoid, a surgeon can place the suture anchors at the anatomical insertions of the coracoclavicular ligament and allow the dislocated joint reduced and maintained well. Level IV, Case series; therapeutic study.

The anchoring bias reflects rational use of cognitive resources

OpenAIRE

Goodman, Noah; Huys, Quentin; Griffiths, Tom; Lieder, Falk

2017-01-01

© 2017, Psychonomic Society, Inc. Cognitive biases, such as the anchoring bias, pose a serious challenge to rational accounts of human cognition. We investigate whether rational theories can meet this challenge by taking into account the mind’s bounded cognitive resources. We asked what reasoning under uncertainty would look like if people made rational use of their finite time and limited cognitive resources. To answer this question, we applied a mathematical theory of bounded rationality to...

Facile Synthesis of SiO2@C Nanoparticles Anchored on MWNT as High-Performance Anode Materials for Li-ion Batteries

Science.gov (United States)

Zhao, Yan; Liu, Zhengjun; Zhang, Yongguang; Mentbayeva, Almagul; Wang, Xin; Maximov, M. Yu.; Liu, Baoxi; Bakenov, Zhumabay; Yin, Fuxing

2017-07-01

Carbon-coated silica nanoparticles anchored on multi-walled carbon nanotubes (SiO2@C/MWNT composite) were synthesized via a simple and facile sol-gel method followed by heat treatment. Scanning and transmission electron microscopy (SEM and TEM) studies confirmed densely anchoring the carbon-coated SiO2 nanoparticles onto a flexible MWNT conductive network, which facilitated fast electron and lithium-ion transport and improved structural stability of the composite. As prepared, ternary composite anode showed superior cyclability and rate capability compared to a carbon-coated silica counterpart without MWNT (SiO2@C). The SiO2@C/MWNT composite exhibited a high reversible discharge capacity of 744 mAh g-1 at the second discharge cycle conducted at a current density of 100 mA g-1 as well as an excellent rate capability, delivering a capacity of 475 mAh g-1 even at 1000 mA g-1. This enhanced electrochemical performance of SiO2@C/MWNT ternary composite anode was associated with its unique core-shell and networking structure and a strong mutual synergistic effect among the individual components.

Crystal structures of two thiacalix[4]arene derivatives anchoring four ...

Indian Academy of Sciences (India)

Administrator

Abstract. The crystal structures of two thiacalixarene derivatives anchoring thiadiazole functional groups at lower rim, C60H72O4S12N8 (1), C64H80O4S12N8 (2), have been determined by single crystal X-ray diffraction. The thiacalix[4]arene framework in both 1 and 2 adopts the 1,3-alternate conformation. Com- pound 1 ...

Membrane Curvature and Lipid Composition Synergize To Regulate N-Ras Anchor Recruitment

DEFF Research Database (Denmark)

Larsen, Jannik B.; Kennard, Celeste; Pedersen, Søren L.

2017-01-01

Proteins anchored to membranes through covalently linked fatty acids and/or isoprenoid groups play crucial roles in all forms of life. Sorting and trafficking of lipidated proteins has traditionally been discussed in the context of partitioning to membrane domains of different lipid composition. We...

Biomechanical properties of double- and single-row suture anchor repair for surgical treatment of insertional Achilles tendinopathy.

Science.gov (United States)

Beitzel, Knut; Mazzocca, Augustus D; Obopilwe, Elifho; Boyle, James W; McWilliam, James; Rincon, Lina; Dhar, Yasmin; Arciero, Robert A; Amendola, Annunziato

2013-07-01

Because of intratendinous ossifications, retrocalcaneal bursitis, or intratendinous necrosis commonly found in insertional tendinosis, it is often necessary to detach the tendon partially or entirely from its tendon-to-bone junction. Double-row repair for insertional Achilles tendinopathy will generate an increased contact area and demonstrate higher biomechanical stability. Controlled laboratory study. Eighteen cadaver Achilles tendons were split longitudinally and detached, exposing the calcaneus; an ostectomy was performed and the tendon was reattached to the calcaneus in 1 of 2 ways: 2 suture anchors (single row) or a 4-anchor (double row) construct. Footprint area measurements over time, displacement after cyclic loading (2000 cycles), and final load to failure were measured. The double-row refixation technique was statistically superior to the single-row technique in footprint area measurement initially and 5 minutes after repair (P = .009 and P = .01, respectively) but not after 24 hours (P = .713). The double-row construct demonstrated significantly improved measures for peak load (433.9 ± 84.3 N vs 212.0 ± 49.7 N; P = .042), load at yield (354.7 ± 106.2 N vs 198.7 ± 39.5 N; P = .01), and slope (51.8 ± 9.9 N/mm vs 66.7 ± 16.2 N/mm; P = .021). Cyclic loading did not demonstrate significant differences between the 2 constructs. Double-row construct for reinsertion of a completely detached Achilles tendon using proximal and distal rows resulted in significantly larger contact area initially and 5 minutes after repair and led to significantly higher peak load to failure on destructive testing. In treatment for insertional Achilles tendinosis, the tendon often has to be detached and anatomically reattached to its insertion at the calcaneus. To our knowledge there is a lack of biomechanical studies supporting either a number or a pattern of suture anchor fixation. Because the stresses going across the insertion site of the Achilles tendon are significant

Curcumin Protects Neurons from Glutamate-Induced Excitotoxicity by Membrane Anchored AKAP79-PKA Interaction Network

Directory of Open Access Journals (Sweden)

Kui Chen

2015-01-01

Full Text Available Now stimulation of AMPA receptor as well as its downstream pathways is considered as potential central mediators in antidepressant mechanisms. As a signal integrator which binds to AMPA receptor, A-kinase anchoring protein 79-(AKAP79- PKA complex is regarded as a potential drug target to exert neuroprotective effects. A well-tolerated and multitarget drug curcumin has been confirmed to exert antidepressant-like effects. To explore whether AKAP79-PKA complex is involved in curcumin-mediated antiexcitotoxicity, we detected calcium signaling, subcellular location of AKAP79-PKA complex, phosphorylation of glutamate receptor, and ERK and AKT cascades. In this study, we found that curcumin protected neurons from glutamate insult by reducing Ca2+ influx and blocking the translocation of AKAP79 from cytomembrane to cytoplasm. In parallel, curcumin enhanced the phosphorylation of AMPA receptor and its downstream pathways in PKA-dependent manner. If we pretreated cells with PKA anchoring inhibitor Ht31 to disassociate PKA from AKAP79, no neuroprotective effects were observed. In conclusion, our results show that AKAP79-anchored PKA facilitated the signal relay from AMPA receptor to AKT and ERK cascades, which may be crucial for curcumin-mediated antiexcitotoxicity.

Preparation of raspberry-like γ-Fe2O3/crackled nitrogen-doped carbon capsules and their application as supports to improve catalytic activity.

Science.gov (United States)

Zhang, Junshuai; Yao, Tongjie; Zhang, Hui; Zhang, Xiao; Wu, Jie

2016-11-10

In this manuscript, we have introduced a novel method to improve the catalytic activity of metal nanoparticles via optimizing the support structure. To this end, raspberry-like γ-Fe 2 O 3 /crackled nitrogen-doped carbon (CNC) capsules were prepared by a two-step method. Compared with traditional magnetic capsules, in γ-Fe 2 O 3 /CNC capsules, the γ-Fe 2 O 3 nanoparticles were embedded in a CNC shell; therefore, they neither occupied the anchoring sites for metal nanoparticles nor came into contact with them, which was beneficial for increasing the metal nanoparticle loading. Numerous tiny cracks appeared on the porous CNC shell, which effectively improved the mass diffusion and transport in catalytic reactions. Additionally, the coordination interaction could be generated between the precursor metal ions and doped-nitrogen atoms in the capsule shell. With the help of these structural merits, γ-Fe 2 O 3 /CNC capsules were ideal supports for Pd nanoparticles, because they were beneficial for improving the Pd loading, reducing the nanoparticle size, increasing their dispersity and maximizing the catalytic performance of Pd nanoparticles anchored on the inner shell surface. As expected, γ-Fe 2 O 3 /CNC@Pd catalysts exhibited a dramatically enhanced catalytic activity towards hydrophilic 4-nitrophenol and hydrophobic nitrobenzene. The reaction rate constant k was compared with recent work and the corresponding reference samples. Moreover, they could be easily recycled by using a magnet and reused without an obvious loss of catalytic activity.

Aspartate tightens the anchoring of staphylococcal lipoproteins to the cytoplasmic membrane.

Science.gov (United States)

Kumari, Nimerta; Götz, Friedrich; Nguyen, Minh-Thu

2017-12-01

In gram-negative bacteria, the ABC transporter LolCDE complex translocates outer membrane-specific lipoproteins (Lpp) from the inner membrane to the outer membrane. Lpp possessing aspartate (Asp) at position +2 are not translocated because it functions as a LolCDE avoidance signal. In gram-positive bacteria, lacking an outer membrane and the Lol system, Lpp are only anchored at the outer leaflet of the cytoplasmic membrane. However, the release of Lpp particularly in pathogenic or commensal species is crucial for immune modulation. Here, we provide evidence that in Staphylococcus aureus Asp at position +2 plays a role in withholding Lpp to the cytoplasmic membrane. Screening of published exoproteomic data of S. aureus revealed that Lpp mainly with Gly or Ser at position +2 were found in exoproteome, but there was no Lpp with Asp+2. The occurrence of Lpp with Asp+2 is infrequent in gram-positive bacteria. In S. aureus USA300 only seven of the 67 Lpp possess Asp+2; among them five Lpp represented Lpl lipoproteins involved in host cell invasion. Our study demonstrated that replacing the Asp+2 present in Lpl8 with a Ser enhances its release into the supernatant. However, there is no different release of Asp+2 and Ser+2 in mprF mutant that lacks the positive charge of lysyl-phosphatidylglycerol (Lys-PG). Moreover, substitution of Ser+2 by Asp in SitC (MntC) did not lead to a decreased release indicating that in staphylococci positions +3 and +4 might also be important for a tighter anchoring of Lpp. Here, we show that Asp in position +2 and adjacent amino acids contribute in tightening the anchoring of Lpp by interaction of the negative charged Asp with the positive charged Lys-PG. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Active appearance pyramids for object parametrisation and fitting.

Science.gov (United States)

Zhang, Qiang; Bhalerao, Abhir; Dickenson, Edward; Hutchinson, Charles

2016-08-01

Object class representation is one of the key problems in various medical image analysis tasks. We propose a part-based parametric appearance model we refer to as an Active Appearance Pyramid (AAP). The parts are delineated by multi-scale Local Feature Pyramids (LFPs) for superior spatial specificity and distinctiveness. An AAP models the variability within a population with local translations of multi-scale parts and linear appearance variations of the assembly of the parts. It can fit and represent new instances by adjusting the shape and appearance parameters. The fitting process uses a two-step iterative strategy: local landmark searching followed by shape regularisation. We present a simultaneous local feature searching and appearance fitting algorithm based on the weighted Lucas and Kanade method. A shape regulariser is derived to calculate the maximum likelihood shape with respect to the prior and multiple landmark candidates from multi-scale LFPs, with a compact closed-form solution. We apply the 2D AAP on the modelling of variability in patients with lumbar spinal stenosis (LSS) and validate its performance on 200 studies consisting of routine axial and sagittal MRI scans. Intervertebral sagittal and parasagittal cross-sections are typically used for the diagnosis of LSS, we therefore build three AAPs on L3/4, L4/5 and L5/S1 axial cross-sections and three on parasagittal slices. Experiments show significant improvement in convergence range, robustness to local minima and segmentation precision compared with Constrained Local Models (CLMs), Active Shape Models (ASMs) and Active Appearance Models (AAMs), as well as superior performance in appearance reconstruction compared with AAMs. We also validate the performance on 3D CT volumes of hip joints from 38 studies. Compared to AAMs, AAPs achieve a higher segmentation and reconstruction precision. Moreover, AAPs have a significant improvement in efficiency, consuming about half the memory and less than 10% of

Cultural Anchors and the Organization of Differences: A Multi-method Analysis of LGBT Marches on Washington

Science.gov (United States)

Ghaziani, Amin; Baldassarri, Delia

2013-01-01

Social scientists describe culture as either coherent or incoherent and political dissent as either unifying or divisive. This article moves beyond such dichotomies. Content, historical, and network analyses of public debates on how to organize four lesbian, gay, bisexual, and transgender (LGBT) Washington marches provide evidence for an integrative position. Rather than just describe consistencies or contradictions, we contend that the key analytic challenge is to explain the organization of differences. We propose one way of doing this using the mechanism of a cultural anchor. Within and across marches, a small collection of ideas remains fixed in the national conversation, yet in a way that allows activists to address their internal diversity and respond to unfolding historical events. These results suggest that activists do not simply organize around their similarities but, through cultural anchors, they use their commonalities to build a thinly coherent foundation that can also support their differences. Situated at the nexus of culture, social movements, sexualities, and networks, this article demonstrates how the anchoring mechanism works in the context of LGBT political organizing. PMID:23661809

New 'one-step' method for the simultaneous synthesis and anchoring of organic monolith inside COC microchip channels

International Nuclear Information System (INIS)

Ladner, Yoann; Cretier, Gerard; Dugas, Vincent; Randon, Jerome; Faure, Karine; Bruchet, Anthony

2012-01-01

A new method for monolith synthesis and anchoring inside cyclic olefin copolymer (COC) microchannels in a single step is proposed. It is shown that type I photo-initiators, typically used in a polymerization mixture to generate free radicals during monolith synthesis, can simultaneously act as type II photo-initiators and react with the plastic surface through hydrogen abstraction. This mechanism is used to 'photo-graft' poly(ethylene glycol) methacrylate (PEGMA) on COC surfaces. Contact angle measurements were used to observe the changes in surface hydrophilicity when increasing initiator concentration and irradiation duration. The ability of type I photo-initiators to synthesize and anchor a monolith inside COC microchannels in a single step was proved through SEM observations. Different concentrations of photo-initiators were tried. Finally, electro-chromatographic separations of polycyclic aromatic hydrocarbons were realized to illustrate the beneficial effect of anchoring on chromatographic performances. The versatility of the method was demonstrated with two widely used photo-initiators: benzoin methyl ether (BME) and azobisisobutyronitrile (AIBN). (authors)

The moderated relationship of appearance valence on appearance self consciousness: development and testing of new measures of appearance schema components.

Directory of Open Access Journals (Sweden)

Timothy P Moss

Full Text Available This paper describes the creation and psychometric properties of two independent measures of aspects of appearance schematicity--appearance salience and valence, assessed by the CARSAL and CARVAL, and their relation to appearance self-consciousness. Five hundred and ninety two participants provided data in a web based task. The results demonstrate the sound psychometric properties of both scales. This was demonstrated by good item total characteristics, good internal reliability of each scale, and the independence of the two scales shown through principal components analysis. Furthermore, the scales show independent and moderated relationships with valid measures of appearance related psychosocial distress. Negatively valenced appearance information was associated with increased appearance self-consciousness. More crucially, the impact of negative valence on appearance self-consciousness was exacerbated by the moderating effect increased salience of appearance.

A biomechanical comparison of 2 transosseous-equivalent double-row rotator cuff repair techniques using bioabsorbable anchors: cyclic loading and failure behavior.

Science.gov (United States)

Spang, Jeffrey T; Buchmann, Stefan; Brucker, Peter U; Kouloumentas, Panos; Obst, Tobias; Schröder, Manuel; Burgkart, Rainer; Imhoff, Andreas B

2009-08-01

A novel double-row configuration was compared with a traditional double-row configuration for rotator cuff repair. In 10 matched-pair sheep shoulders in vitro repair was performed with either a double-row technique with corkscrew suture anchors for the medial row and insertion anchors for the lateral row (group A) or a double-row technique with a new tape-like suture material with insertion anchors for both the medial and lateral rows (group B). Each specimen underwent cyclic loading from 10 to 150 N for 100 cycles, followed by unidirectional failure testing. Gap formation and strain within the repair area for the first and last cycles were analyzed with a video digitizing system, and stiffness and failure load were determined from the load-elongation curve. The results were similar for the 2 repair types. There was no significant difference between the ultimate failure loads of the 2 techniques (421 +/- 150 N in group A and 408 +/- 66 N in group B, P = .31) or the stiffness of the 2 techniques (84 +/- 26 N/mm in group A and 99 +/- 20 N/mm in group B, P = .07). In addition, gap formation was not different between the repair types. Strain over the repair area was also not different between the repair types. Both tested rotator cuff repair techniques had high failure loads, limited gap formation, and acceptable strain patterns. No significant difference was found between the novel and conventional double-row repair types. Two double-row techniques-one with corkscrew suture anchors for the medial row and insertion anchors for the lateral row and one with insertion anchors for both the medial and lateral rows-provided excellent biomechanical profiles at time 0 for double-row repairs in a sheep model. Although the sheep model may not directly correspond to in vivo conditions, all-insertion anchor double-row constructs are worthy of further investigation.

All-inside arthroscopic lateral collateral ligament repair for ankle instability with a knotless suture anchor technique.

Science.gov (United States)

Vega, Jordi; Golanó, Pau; Pellegrino, Alexandro; Rabat, Eduard; Peña, Fernando

2013-12-01

Recently, arthroscopic-assisted techniques have been described to treat lateral ankle instability with excellent results. However, complications including neuritis of the superficial peroneal or sural nerve, and pain or discomfort due to a prominent anchor or suture knot have been reported. The aim of this study was to describe a novel technique, the "all-inside arthroscopic lateral collateral ankle ligament repair," and its results for treating patients with ankle instability. Sixteen patients (10 men and 6 women, mean age 29.3 years, 17-46) with lateral ankle instability were treated with an arthroscopic procedure. Using a suture passer and a knotless anchor, the ligaments were repaired with an all-inside technique. The right ankle was affected in 10 cases. Mean follow-up was 22.3 (12-35) months. On arthroscopic examination, 13 patients had an isolated anterior talofibular ligament (ATFL) injury, and in 3 patients, both the ATFL and calcaneofibular ligament (CFL) were affected. All-inside arthroscopic anatomic repair of the lateral collateral ligament complex was performed in all cases. All patients reported subjective improvement of their ankle instability. The mean AOFAS score increased from 67 preoperatively to 97 at final follow-up. No major complications were reported. The all-inside arthroscopic ligament repair was a safe, reliable, and reproducible technique that both provided an anatomic repair of the lateral collateral ligament complex and restored ankle stability while preserving all the advantages of an arthroscopic technique. Level IV, retrospective case series.

INAA, AAS, and lead isotope analysis of ancient lead anchors from the black SEA

International Nuclear Information System (INIS)

Kuleff, I.; Djingova, R.; Alexandrova, A.

1995-01-01

Lead stock of wooden-lead anchors found along the Bulgarian Black Sea coast and typo logically dated VI c. B.C. - III c. A.D. have been analyzed for chemical composition and lead isotope ratios by INAA, AAS and mass spectrometry. Using multivariate methods for analysis as well as simple bi variate plots the lead for production of the stocks was localized as originating from Laurion, Thassos, Troas, Chalkidike and the Rhodopes. In general, the chemical composition is not recommended to be used for provenance study of lead artefacts. Combining the results from this study with the existing typo logical classification certain conclusion about the production and distribution of lead anchors in the Aegean region are made. (author). 22 refs., 3 figs., 4 tabs

Note on the hydrodynamic description of thin nematic films: Strong anchoring model

KAUST Repository

Lin, Te-Sheng; Cummings, Linda J.; Archer, Andrew J.; Kondic, Lou; Thiele, Uwe

2013-01-01

We discuss the long-wave hydrodynamic model for a thin film of nematic liquid crystal in the limit of strong anchoring at the free surface and at the substrate. We rigorously clarify how the elastic energy enters the evolution equation for the film thickness in order to provide a solid basis for further investigation: several conflicting models exist in the literature that predict qualitatively different behaviour. We consolidate the various approaches and show that the long-wave model derived through an asymptotic expansion of the full nemato-hydrodynamic equations with consistent boundary conditions agrees with the model one obtains by employing a thermodynamically motivated gradient dynamics formulation based on an underlying free energy functional. As a result, we find that in the case of strong anchoring the elastic distortion energy is always stabilising. To support the discussion in the main part of the paper, an appendix gives the full derivation of the evolution equation for the film thickness via asymptotic expansion. © 2013 AIP Publishing LLC.

Conceptual design of cooling anchor for current lead on HTS field coils

Energy Technology Data Exchange (ETDEWEB)

Hyeon, C. J.; Kim, J. H.; Quach, H. L. [Dept. of Electrical Engineering, Jeju National University, Jeju (Korea, Republic of); and others

2017-06-15

The role of current lead in high-temperature superconducting synchronous machine (HTSSM) is to function as a power supply by connecting the power supply unit at room temperature with the HTS field coils at cryogenic temperature. Such physical and electrical connection causes conduction and Joule-heating losses, which are major thermal losses of HTSSM rotors. To ensure definite stability and economic feasibility of HTS field coils, quickly and smoothly cooling down the current lead is a key design technology. Therefore, in this paper, we introduce a novel concept of a cooling anchor to enhance the cooling performance of a metal current lead. The technical concept of this technology is the simultaneously chilling and supporting the current lead. First, the structure of the current lead and cooling anchor were conceptually designed for field coils for a 1.5 MW-class HTSSM. Then, the effect of this installation on the thermal characteristics of HTS coils was investigated by 3D finite element analysis.

Glycolipid precursors for the membrane anchor of Trypanosoma brucei variant surface glycoproteins. II. Lipid structures of phosphatidylinositol-specific phospholipase C sensitive and resistant glycolipids

International Nuclear Information System (INIS)

Mayor, S.; Menon, A.K.; Cross, G.A.

1990-01-01

A common diagnostic feature of glycosylinositol phospholipid (GPI)-anchored proteins is their release from the membrane by a phosphatidylinositol-specific phospholipase C (PI-PLC). However, some GPI-anchored proteins are resistant to this enzyme. The best characterized example of this subclass is the human erythrocyte acetylcholinesterase, where the structural basis of PI-PLC resistance has been shown to be the acylation of an inositol hydroxyl group(s). Both PI-PLC-sensitive and resistant GPI-anchor precursors (P2 and P3, respectively) have been found in Trypanosoma brucei, where the major surface glycoprotein is anchored by a PI-PLC-sensitive glycolipid anchor. The accompanying paper shows that P2 and P3 have identical glycans, indistinguishable from the common core glycan found on all the characterized GPI protein anchors. This paper shows that the single difference between P2 and P3, and the basis for the PI-PLC insusceptibility of P3, is a fatty acid, ester-linked to the inositol residue in P3. The inositol-linked fatty acid can be removed by treatment with mild base to restore PI-PLC sensitivity. Biosynthetic labeling experiments with [3H]palmitic acid and [3H]myristic acid show that [3H]palmitic acid specifically labels the inositol residue in P3 while [3H]myristic acid labels the diacylglycerol portion. Possible models to account for the simultaneous presence of PI-PLC-resistant and sensitive glycolipids are discussed in the context of available information on the biosynthesis of GPI-anchors

'Saurashtra stone anchors' (Ring-stones) from Dwarka and Somnath, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Gaur, A.S.; Sundaresh; Tripati, S.; Gudigar, P.; Bandodkar, S.N.

Last two decades of marine archaeological research along the Indian coast has brought to light a large number of stone anchors of different types and sizes, indicating that the Indian coast has witnessed brisk maritime activities in the past...

Endometrial ablation: normal appearance and complications.

Science.gov (United States)

Drylewicz, Monica R; Robinson, Kathryn; Siegel, Cary Lynn

2018-03-14

Global endometrial ablation is a commonly performed, minimally invasive technique aimed at improving/resolving abnormal uterine bleeding and menorrhagia in women. As non-resectoscopic techniques have come into existence, endometrial ablation performance continues to increase due to accessibility and decreased requirements for operating room time and advanced technical training. The increased utilization of this method translates into increased imaging of patients who have undergone the procedure. An understanding of the expected imaging appearances of endometrial ablation using different modalities is important for the abdominal radiologist. In addition, the frequent usage of the technique naturally comes with complications requiring appropriate imaging work-up. We review the expected appearance of the post-endometrial ablated uterus on multiple imaging modalities and demonstrate the more common and rare complications seen in the immediate post-procedural time period and remotely.

Enhanced vapor transport in membrane distillation via functionalized carbon nanotubes anchored into electrospun nanofibres

KAUST Repository

An, Alicia Kyoungjin; Lee, Eui-Jong; Guo, Jiaxin; Jeong, Sanghyun; Lee, Jung Gil; Ghaffour, NorEddine

2017-01-01

To ascertain membrane distillation (MD) as an emerging desalination technology to meet the global water challenge, development of membranes with ideal material properties is crucial. Functionalized carbon nanotubes (CNTs) were anchored to nanofibres of electrospun membranes. Covalent modification and fluorination of CNTs improved their dispersibility and interfacial interaction with the polymer membrane, resulting in well-aligned CNTs inside crystalline fibres with superhydrophobicity. Consideration for the chemical/physical properties of the CNT composite membranes and calculation of their theoretical fluxes revealed the mechanism of MD: CNTs facilitated the repulsive force for Knudsen and molecular diffusions, reduced the boundary-layer effect in viscous flow, and assisted surface diffusion, allowing for fast vapor transport with anti-wetting. This study shows that the role of CNTs and an optimal composite ratio can be used to reduce the gap between theoretical and experimental approaches to desalination.

Enhanced vapor transport in membrane distillation via functionalized carbon nanotubes anchored into electrospun nanofibres

KAUST Repository

An, Alicia Kyoungjin

2017-01-30

To ascertain membrane distillation (MD) as an emerging desalination technology to meet the global water challenge, development of membranes with ideal material properties is crucial. Functionalized carbon nanotubes (CNTs) were anchored to nanofibres of electrospun membranes. Covalent modification and fluorination of CNTs improved their dispersibility and interfacial interaction with the polymer membrane, resulting in well-aligned CNTs inside crystalline fibres with superhydrophobicity. Consideration for the chemical/physical properties of the CNT composite membranes and calculation of their theoretical fluxes revealed the mechanism of MD: CNTs facilitated the repulsive force for Knudsen and molecular diffusions, reduced the boundary-layer effect in viscous flow, and assisted surface diffusion, allowing for fast vapor transport with anti-wetting. This study shows that the role of CNTs and an optimal composite ratio can be used to reduce the gap between theoretical and experimental approaches to desalination.

A cell-surface-anchored ratiometric i-motif sensor for extracellular pH detection.

Science.gov (United States)

Ying, Le; Xie, Nuli; Yang, Yanjing; Yang, Xiaohai; Zhou, Qifeng; Yin, Bincheng; Huang, Jin; Wang, Kemin

2016-06-14

A FRET-based sensor is anchored on the cell surface through streptavidin-biotin interactions. Due to the excellent properties of the pH-sensitive i-motif structure, the sensor can detect extracellular pH with high sensitivity and excellent reversibility.

Single-incision laparoscopic surgery in a survival animal model using a transabdominal magnetic anchoring system.

Science.gov (United States)

Cho, Yong Beom; Park, Chan Ho; Kim, Hee Cheol; Yun, Seong Hyeon; Lee, Woo Yong; Chun, Ho-Kyung

2011-12-01

Though single-incision laparoscopic surgery (SILS) can reduce operative scarring and facilitates postoperative recovery, it does have some limitations, such as reduction in instrument working, difficulty in triangulation, and collision of instruments. To overcome these limitations, development of new instruments is needed. The aim of this study is to evaluate the feasibility and safety of a magnetic anchoring system in performing SILS ileocecectomy. Experiments were performed in a living dog model. Five dogs (26.3-29.2 kg) underwent ileocecectomy using a multichannel single port (OCTO port; Darim, Seoul, Korea). The port was inserted at the umbilicus and maintained a CO(2) pneumoperitoneum. Two magnet-fixated vascular clips were attached to the colon using an endoclip applicator, and it was held together across the abdominal wall by using an external handheld magnet. The cecum was then retracted in an upward direction by moving the external handheld magnet, and the mesocolon was dissected with Ultracision(®). Extracorporeal functional end-to-end anastomosis was done using a linear stapler. All animals survived during the observational period of 2 weeks, and then re-exploration was performed under general anesthesia for evaluation of intra-abdominal healing and complications. Mean operation time was 70 min (range 55-100 min), with each subsequent case taking less time. The magnetic anchoring system was effective in achieving adequate exposure in all cases. All animals survived and convalesced normally without evidence of clinical complication during the observation period. At re-exploration, all anastomoses were completely healed and there were no complications such as abscess, bleeding or organ injury. SILS ileocecectomy using a magnetic anchoring system was safe and effective in a dog model. The development of magnetic anchoring systems may be beneficial for overcoming the limitations of SILS.

Effects of an Anchoring Configuration on the Static Response of Geotextile and Geogrid Fabrics

National Research Council Canada - National Science Library

Simmons, Lebron

2000-01-01

An investigation is made of a potential retrofit system for in-fill masonry walls subjected to blast effects that consist of geotextile or geogrid materials anchored to the roof, floor slabs and beams...

Intraoperative Ultrasound-Guided Removal of Retained Mini Sling Anchor Causing Vaginal Pain: A Case Report.

Science.gov (United States)

Almassi, Nima; Goldman, Howard B

2016-01-01

Since the introduction of the tension-free vaginal tape, the surgical management of female stress urinary incontinence has undergone a dramatic shift toward synthetic midurethral slings (MUSs). The evolution of the MUS has led to the development of the single incision mini sling (SIMS), a minimally invasive procedure that can be performed under local anesthesia. Complications arising after SIMS placement parallel those of the traditional MUS, including pelvic pain, dyspareunia, and mesh erosion. The patient in this case presented with persistent pelvic pain due to a retained SIMS anchor after having previously undergone SIMS placement and subsequent transvaginal exploration with mesh removal. We report the use of intraoperative ultrasound for identification and removal of the retained SIMS anchor.

Initial clinical experience with a sac-anchoring endoprosthesis for aortic aneurysm repair.

Science.gov (United States)

Donayre, Carlos E; Zarins, Christopher K; Krievins, Dainis K; Holden, Andrew; Hill, Andrew; Calderas, Carlos; Velez, Jaime; White, Rodney A

2011-03-01

All current aortic endografts depend on proximal and distal fixation to prevent migration. However, migration and rupture can occur, particularly in patients with aortic necks that are short or angulated, or both. We present our initial clinical experience with a new sac-anchoring endoprosthesis designed to anchor and seal the device within the aneurysm sac. The initial worldwide experience using a new endoprosthesis for the treatment of aortic aneurysms (Nellix Endovascular, Palo Alto, Calif) was reviewed. The endoprosthesis consists of dual balloon-expandable endoframes surrounded by polymer-filled endobags designed to obliterate the aneurysm sac and maintain endograft position. Clinical results and follow-up contrast computed tomography (CT) scans at 30 days and 6 and 12 months were reviewed. The endograft was successfully deployed in 21 patients with infrarenal aortic aneurysms measuring 5.7 ± 0.7 cm (range, 4.3-7.4 cm). Two patients with common iliac aneurysms were treated with sac-anchoring extenders that maintained patency of the internal iliac artery. Infusion of 71 ± 37 mL of polymer (range, 19-158 mL) into the aortic endobags resulted in complete aneurysm exclusion in all patients. Mean implant time was 76 ± 35 minutes, with 33 ± 17 minutes of fluoroscopy time and 180 ± 81 mL of contrast; estimated blood loss was 174 ± 116 mL. One patient died during the postoperative period (30-day mortality, 4.8%), and one died at 10 months from non-device-related causes. During a mean follow-up of 8.7 ± 3.1 months and a median of 6.3 months, there were no late aneurysm- or device-related adverse events and no secondary procedures. CT imaging studies at 6 months and 1 year revealed no increase in aneurysm size, no device migration, and no new endoleaks. One patient had a limited proximal type I endoleak at 30 days that resolved at 60 days and remained sealed. One patient has an ongoing distal type I endoleak near the iliac bifurcation, with no change in aneurysm

Suture anchor tenodesis in repair of distal Achilles tendon injuries.

Science.gov (United States)

Kiliçoğlu, Onder; Türker, Mehmet; Yildız, Fatih; Akalan, Ekin; Temelli, Yener

2014-01-01

Distal Achilles tendon avulsions are in the form of either bony and nonbony avulsion of Achilles tendon from its calcaneal insertion. Four patients with distal Achilles tendon avulsions or ruptures which were treated with tendon to bone repair using suture anchors are presented here. Operated leg was immobilized in above-knee cast for 4 weeks while the patient walked non-weight-bearing. Then, cast was changed to below knee, and full weight-bearing was allowed. Patients underwent gait analysis minimum at first postoperative year. Mean American Orthopedics Foot Ankle Society ankle/hindfoot score of patients at last visit was 88.75 (range 85-100), and Achilles tendon total rupture score was 77.75 (range 58-87). Mean passive dorsiflexion of injured ankles (14° ± 5°) was lower than uninjured ankles (23° ± 9°). All the kinematic parameters of gait analysis were comparable to the uninjured side. Maximum plantar flexion power of injured ankle was 1.40 W/kg, and this was significantly lower than the contralateral side value 2.38 W/kg; (P = 0.0143). There were no visually altered gait or problems in daily life. Suture anchor tenodesis technique of distal Achilles tendon avulsions was successful in achieving durable osteotendinous repairs.

Protein kinase C zeta suppresses low- or high-grade colorectal cancer (CRC) phenotypes by interphase centrosome anchoring.

Science.gov (United States)

Deevi, Ravi Kiran; Javadi, Arman; McClements, Jane; Vohhodina, Jekaterina; Savage, Kienan; Loughrey, Maurice Bernard; Evergren, Emma; Campbell, Frederick Charles

2018-04-01

Histological grading provides prognostic stratification of colorectal cancer (CRC) by scoring heterogeneous phenotypes. Features of aggressiveness include aberrant mitotic spindle configurations, chromosomal breakage, and bizarre multicellular morphology, but pathobiology is poorly understood. Protein kinase C zeta (PKCz) controls mitotic spindle dynamics, chromosome segregation, and multicellular patterns, but its role in CRC phenotype evolution remains unclear. Here, we show that PKCz couples genome segregation to multicellular morphology through control of interphase centrosome anchoring. PKCz regulates interdependent processes that control centrosome positioning. Among these, interaction between the cytoskeletal linker protein ezrin and its binding partner NHERF1 promotes the formation of a localized cue for anchoring interphase centrosomes to the cell cortex. Perturbation of these phenomena induced different outcomes in cells with single or extra centrosomes. Defective anchoring of a single centrosome promoted bipolar spindle misorientation, multi-lumen formation, and aberrant epithelial stratification. Collectively, these disturbances induce cribriform multicellular morphology that is typical of some categories of low-grade CRC. By contrast, defective anchoring of extra centrosomes promoted multipolar spindle formation, chromosomal instability (CIN), disruption of glandular morphology, and cell outgrowth across the extracellular matrix interface characteristic of aggressive, high-grade CRC. Because PKCz enhances apical NHERF1 intensity in 3D epithelial cultures, we used an immunohistochemical (IHC) assay of apical NHERF1 intensity as an indirect readout of PKCz activity in translational studies. We show that apical NHERF1 IHC intensity is inversely associated with multipolar spindle frequency and high-grade morphology in formalin-fixed human CRC samples. To conclude, defective PKCz control of interphase centrosome anchoring may underlie distinct categories of

Unimpeded permeation of water through biocidal graphene oxide sheets anchored on to 3D porous polyolefinic membranes

Science.gov (United States)

Mural, Prasanna Kumar S.; Jain, Shubham; Kumar, Sachin; Madras, Giridhar; Bose, Suryasarathi

2016-04-01

3D porous membranes were developed by etching one of the phases (here PEO, polyethylene oxide) from melt-mixed PE/PEO binary blends. Herein, we have systematically discussed the development of these membranes using X-ray micro-computed tomography. The 3D tomograms of the extruded strands and hot-pressed samples revealed a clear picture as to how the morphology develops and coarsens over a function of time during post-processing operations like compression molding. The coarsening of PE/PEO blends was traced using X-ray micro-computed tomography and scanning electron microscopy (SEM) of annealed blends at different times. It is now understood from X-ray micro-computed tomography that by the addition of a compatibilizer (here lightly maleated PE), a stable morphology can be visualized in 3D. In order to anchor biocidal graphene oxide sheets onto these 3D porous membranes, the PE membranes were chemically modified with acid/ethylene diamine treatment to anchor the GO sheets which were further confirmed by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and surface Raman mapping. The transport properties through the membrane clearly reveal unimpeded permeation of water which suggests that anchoring GO on to the membranes does not clog the pores. Antibacterial studies through the direct contact of bacteria with GO anchored PE membranes resulted in 99% of bacterial inactivation. The possible bacterial inactivation through physical disruption of the bacterial cell wall and/or reactive oxygen species (ROS) is discussed herein. Thus this study opens new avenues in designing polyolefin based antibacterial 3D porous membranes for water purification.3D porous membranes were developed by etching one of the phases (here PEO, polyethylene oxide) from melt-mixed PE/PEO binary blends. Herein, we have systematically discussed the development of these membranes using X-ray micro-computed tomography. The 3D tomograms of the extruded strands and

Polyacrylonitrile Fibers Anchored Cobalt/Graphene Sheet Nanocomposite: A Low-Cost, High-Performance and Reusable Catalyst for Hydrogen Generation.

Science.gov (United States)

Zhang, Fei; Huang, Guoji; Hou, Chengyi; Wang, Hongzhi; Zhang, Qinghong; Li, Yaogang

2016-06-01

Cobalt and its composites are known to be active and inexpensive catalysts in sodium borohydride (NaBH4) hydrolysis to generate clean and renewable hydrogen energy. A novel fiber catalyst, cobalt/graphene sheet nanocomposite anchored on polyacrylonitrile fibers (Co/GRs-PANFs), which can be easily recycled and used in any reactor with different shapes, were synthesized by anchoring cobalt/graphene (Co/GRs) on polyacrylonitrile fibers coated with graphene (GRs-PANFs) at low temperature. The unique structure design effectively prevents the inter-sheet restacking of Co/GRs and fully exploits the large surface area of novel hybrid material for generate hydrogen. And the extra electron transfer path supplied by GRs on the surface of GRs-PANFs can also enhance their catalysis performances. The catalytic activity of the catalyst was investigated by the hydrolysis of NaBH4 in aqueous solution with GRs-PANFs. GRs powders and Co powders were used as control groups. It was found that both GRs and fiber contributed to the hydrogen generation rate of Co/GRs-PANFs (3222 mL x min(-1) x g(-1)), which is much higher than that of cobalt powders (915 mL x min(-1) x g(-1)) and Co/GRs (995 mL x min(-1) x g(-1)). The improved hydrogen generation rate, low cost and uncomplicated recycling make the Co/GRs-PANFs promising candidate as catalysts for hydrogen generation.

Non-uniformly functionalized titanium carbide-based MXenes as an anchoring material for Li-S batteries: A first-principles calculation

Science.gov (United States)

Sim, Eun Seob; Chung, Yong-Chae

2018-03-01

In this study, the influence of the non-uniform surface of F- and O-functionalized Ti2C on the anchoring behavior of lithium polysulfide (LiPS) is investigated using density functional theory. In order to consider the non-uniform surface, the substitutional, vacancy, and S-trapped sites of F- and O-functionalized Ti2C are designed. The anchoring behavior is investigated considering the adsorption energy of LiPS, reactivity between Li atoms and the substrate, and the reduction state of the S atoms. On the F-substitutional site of the O-functionalized surface, it is confirmed that the suppressing mechanism changes from the neutralization of S atoms to the anchoring of LiPS. However, too strong of an interaction between Ti atoms exposed at the vacancy site and S atoms induces trapping of the S atom at the vacancies of both F- and O-functionalized surfaces. As a result of the trapping of the S atom, the use of active material decreases. In addition, the S-trapped site originated from the vacancy site does not affect the suppressing mechanism. In conclusion, to optimize the Ti2C-based MXene as an anchoring material for Li-S batteries, the preparation process should be focused on eliminating the vacancy of functional groups.