Method of and arrangement for extracting volatile bituminous condensable materials from shales, etc

Energy Technology Data Exchange (ETDEWEB)

Flodin, H G

1918-06-22

A method and arrangement for extracting volatile bituminous condensable materials, such as oils and similar material, as well as sulfur, whereby the material used is heated in a generator by introduction of a hot indifferent gas, such as carbon monoxide or generator gas, which is brought into circulation through a heating apparatus and the generator are characterized by removal of the shales distilled in the generator and their being charged into another generator or furnace where they are oxidized by means of air. Sulfur dioxide and carbon dioxide and possible carbon monoxide are formed and the sulfur dioxide and carbon dioxide formed by the oxidation of the distilled shales are brought into contact with hot coal for regeneration of sulfur and carbon monoxide. The patent contains five additional claims.

Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

Directory of Open Access Journals (Sweden)

Dipankar Sarkar

2016-01-01

Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

Method of recovering oils, etc. , from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1921-05-23

In the low-temperature distillation of bituminous shales or similar bituminous materials with high ash content for recovery of oil etc., steam or inert gases are introduced from outside through gas taps arranged in a circle in the retort. By the method used steam is introduced simultaneously in levels higher and lower than the one in which the gaseous and vaporized products are removed from the shale material and in such a manner that the zone of oil formation chiefly will be between the two places mentioned where vapors or steam are introduced into the retort. The patent has one additional claim.

Carbonizing bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

1921-05-01

A process for carbonizing bituminous minerals, like oil-shale, in a furnace with addition of air in the presence of heat-receiving material is characterized by the fact that to the feed such solid or liquid material (with the exception of oil) is added, which, through vaporization or heat-binding decomposition or conversion, hinders the establishment of excessive temperatures.

Fatigue behaviour of bituminous materials : from binders to mixes

OpenAIRE

SOENEN, H; DE LA ROCHE, C; REDELIUS, P

2003-01-01

Test procedures, aiming at measuring fatigue directly on bituminous binders, are increasingly used. The purpose of this paper is to investigate the relevance of this type of binder fatigue tests and to compare the results with laboratory fatigue properties of the corresponding mixes, using one mix composition for all binders, and similar fatigue tests conditions. Eight binders were selected, derived from two crude sources, including an oxidised and two polymer modified samples. All fatigue te...

Process for carbonizing hard-to-heat bituminous material like shale

Energy Technology Data Exchange (ETDEWEB)

Nagel, K

1921-11-29

A process is described for carbonizing bituminous material, like shale, with the production of sufficient heat for carbonization by burning a part of the bitumen itself by means of a gas stream going in a circuit, to which oxygen in regulated amounts is admitted. It is characterized by the fact that the gas stream already cooled for detarring before its re-entrance into the carbonization chamber is mixed in the inlet channels with an amount of oxygen (air or other free oxygen containing gases), that without sintering or melting of the residue it is burned and the carbonization is carried out evenly.

Advances in Interlaboratory Testing and Evaluation of Bituminous Materials State-of-the-Art Report of the RILEM Technical Committee 206-ATB

CERN Document Server

Bahia, Hussain; Canestrari, Francesco; Roche, Chantal; Benedetto, Hervé; Piber, Herald; Sybilski, Dariusz

2013-01-01

This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.

Bituminization of liquid radioactive waste. Part 3

International Nuclear Information System (INIS)

G'oshev, G.S.; Gradev, G.D.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Stefanov, G.I.

1991-01-01

The elaborated technology for bituminization of liquid radioactive wastes (salt concentrates) is characterized by the fact that the bituminization process takes place in two stages: concentration of the liquid residue and evaporation of the water with simultaneous homogeneous incorporation of the salts in the melted bitumen. An experimental installation for bituminization of salt concentrates was designed on the basis of this technology. The experience accumulated during the design and construction of the installation for bituminization of salt concentrates could be used for designing and constructing an industrial installation for bituminization of the liquid residue of the nuclear power plants. 2 tabs., 3 figs., 3 refs

Design and verification of bituminous mixtures with the increased content of reclaimed asphalt pavement

Science.gov (United States)

Bańkowski, Wojciech; Król, Jan; Gałązka, Karol; Liphardt, Adam; Horodecka, Renata

2018-05-01

Recycling of bituminous pavements is an issue increasingly being discussed in Poland. The analysis of domestic and foreign experience indicates a need to develop this technology in our country, in particular the hot feeding and production technologies. Various steps are being taken in this direction, including research projects. One of them is the InnGA project entitled: “Reclaimed asphalt pavement: Innovative technology of bituminous mixtures using material from reclaimed asphalt pavement”. The paper presents the results of research involving the design of bituminous mixtures in accordance with the required properties and in excess of the content of reclaimed asphalt permitted by the technical guidelines. It presents selected bituminous mixtures with the content of RAP of up to 50% and the results of tests from verification of industrial production of those mixtures. The article discusses the details of the design process of mixtures with a high content of reclaimed asphalt, the carried out production tests and discusses the results of tests under the verification of industrial production. Testing included basic tests according to the Polish technical requirements of WT- 2 and the extended functional testing. The conducted tests and analyses helped to determine the usefulness of the developed bituminous mixtures for use in experimental sections and confirmed the possibility of using an increased amount of reclaimed asphalt up to 50% in mixtures intended for construction of national roads.

Influence of the ionizing radiation on bituminous oil

International Nuclear Information System (INIS)

Aliyeva-Chichek, S.N; Guliyeva, S.; Aliyev, S.; Ahmedbekova, N. Ibadov.

2012-01-01

Full text : Bituminous oil is suitable for the production of road bitumen, lubricant oils, and energy fuel. In their structure, there is found an increased concentration of valuable metals (vanadium, nickel, etc.). The radiation-chemical transformations of bituminous oil, as well as the influence of an ionizing radiation on radiating stability of oil were investigated. Investigated oil was taken from Binagadi deposits from a depth in excess of 100 m.The source of ionizing radiation was used the isotope γ radiation 20 60 Ca MRX - γ 30 . The dose rate of the source of radiation is 0, 49 Gy/s, at the absorbed doses of 34,5-216 kGy. Methods of IR-Spectroscopy with an application of Spectrometer M-80 were used in the determination of the structural-group componential composition. Gas products were analyzed with the method of gas chromatography. Liquid products were identified by mass-spectrometer methods. The kinetics of the formations of gases was investigated by the radiolysis of oil as one of the parameters of the radiating stability of the bituminous oil. Samples of oil were irradiated in a vacuum and air conditions. It was established that presence of oxygen in the system does not significantly influence the radiation-chemical yields of the gases. Because at the room temperature, radiation-chemical disintegration proceeds without the introduction of oxygen into the reaction. This means that the rate of regrouping and splitting in the polycondensed systems is greater than the rate of interaction of the active radiolysis particles with oxygen. The influence of γ - irradiation on the structural-group composition of bituminous oil was investigated. It is visible from the comparison of IR-spectra of initial and irradiated samples of oil in the presence of air and in a vacuum, that there is a decrease in the optical density as a result of irradiation both in the aliphatic groups -CH 2 , -CH 3 , and in the double chemical bonds C=C. This shows that formation of

Shaft-retort for treating waste materials, like washery waste, bituminous shale, oil-bearing sands and the like

Energy Technology Data Exchange (ETDEWEB)

Koppers, H

1916-10-29

A shaft-retort for converting waste materials, like washery waste, bituminous shale, oil-bearing sands, brown coal and non-coking mineral coal to oil and tar by supplying heat through the shaft wall formed of an iron-sheet to the material, which is forced through a feeding member perforated for the removal of gases and vapors, and moved downward in a thin layer on the shaft wall; that is characterized by the fact that the iron heating sheet is made rotatable for the purpose of equalizing overheating of itself and the material to be treated.

Recovering bituminous matter from shale

Energy Technology Data Exchange (ETDEWEB)

Ryan, H D

1922-08-29

A process is described for obtaining valuable hydro-carbons from bituminous solids such as shale and the like, which comprises digesting a mixture of such a bituminous solid with a hydro-carbon liquid, the digestion being conducted at temperature high enough to effectively liquefy heavy bituminous matter contained in the solid but insufficiently high to effect substantial distillation of heavy bituminous matter, separating a resultant liquid mixture of hydrocarbons from the residue of such bituminous solid and refining the liquid mixture.

Reuse of steel slag in bituminous paving mixtures.

Science.gov (United States)

Sorlini, Sabrina; Sanzeni, Alex; Rondi, Luca

2012-03-30

This paper presents a comprehensive study to evaluate the mechanical properties and environmental suitability of electric arc furnace (EAF) steel slag in bituminous paving mixtures. A variety of tests were executed on samples of EAF slag to characterize the physical, geometrical, mechanical and chemical properties as required by UNI EN specifications, focusing additionally on the volumetric expansion associated with hydration of free CaO and MgO. Five bituminous mixtures of aggregates for flexible road pavement were designed containing up to 40% of EAF slag and were tested to determine Marshall stability and indirect tensile strength. The leaching behaviour of slag samples and bituminous mixtures was evaluated according to the UNI EN leaching test. The tested slag showed satisfactory physical and mechanical properties and a release of pollutants generally below the limits set by the Italian code. Tests on volume stability of fresh materials confirmed that a period of 2-3 months is necessary to reduce effects of oxides hydration. The results of tests performed on bituminous mixtures with EAF slag were comparable with the performance of mixtures containing natural aggregates and the leaching tests provided satisfactory results. Copyright © 2012 Elsevier B.V. All rights reserved.

Report: Potential environmental impact of exempt site materials - a case study of bituminous road planings and waste soils.

Science.gov (United States)

Bark, Marjorie; Bland, Michael; Grimes, Sue

2009-09-01

The use of waste materials for ecological benefit, agricultural improvement or as part of construction works are often exempt from waste management control in order to maximize the reuse of material that would otherwise be disposed of to landfill. It is important, however, to determine whether there is potential for such waste to cause environmental harm in the context of the basis for granting exemptions under the relevant framework objective to ensure that waste is recovered or disposed of without risk to water, air, soil, plants or animals. The potential for environmental harm was investigated by leaching studies on two wastes commonly found at exempt sites: bituminous road planings and waste soils. For bituminous road planings, the organic components of the waste were identified by their solubility in organic solvents but these components would have low environmental impact in terms of bioavailability. Leaching studies of the heavy metals copper, lead and zinc, into the environment, under specific conditions and particularly those modelling acid rain and landfill leachate conditions showed that, except for copper, the amounts leached fell within Waste Acceptance Criteria compliance limits for defining waste as inert waste. The fact that the amount of copper leached was greater than the Waste Acceptance Criteria level suggests that either additional testing of wastes regarded as exempt should be carried out to ensure that they are in analytical compliance or that legislation should allow for the potential benefits of reuse to supersede deviations from analytical compliance.

On the microstructure of bituminous binders

NARCIS (Netherlands)

Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

2014-01-01

The objective of this work is to study the common features and the evolution of microstructures of bituminous binders regardless of their grade (PEN 10/20 to 160/220) and source/origin using the atomic force microscope operated in phase contrast mode. All bituminous binders show the same

Adhesion Promoters in Bituminous Road Materials: A Review

Directory of Open Access Journals (Sweden)

Cesare Oliviero Rossi

2017-05-01

Full Text Available This review focuses on certain classes of organic compounds known variously in the specific literature of asphalt as adhesion promoters, antistripping agents, wetting agents, antistrips, or adhesion agents. These kinds of organic additives are currently formulated to enhance the bitumen coating of mineral aggregates and improve the workability of asphalt mixtures. In this review, the term “adhesion promoters” includes both synthetic organic compounds as well as those extracted from natural resources, mixed in trace amounts to bitumen. Their main role is to alter the interfacial energy, so that the presence of water, even in trace, does not weaken the bitumen-aggregate bond and tends to favor adhesion. The report also considers the chemical functionalities that play a predominant role in bonding, as well as the effects of surface modification of the aggregate due to the presence of adhesion promoters in pre-blended bituminous mixtures. Although bitumen is widely used in road pavement construction and the discussion is mainly addressed to the improvement of adhesion in road materials, adhesion and wetting properties can also represent a general issue in various bitumen-based industrial products.

Bituminization of low- and intermediate-level radioactive concentrates

International Nuclear Information System (INIS)

Breza, M.; Krejci, F.; Timulak, J.; Tibensky, L.

1985-01-01

The results and experiences are summed up from the research and development of the technology of bituminization of low- and intermediate-level radioactive concentrates generated in the operation of nuclear power plants with WWER-440 reactors. The experiments took place on a pilot plant bituminization line with various model solutions at an evaporator capacity of 70, 100 and 140 litres per hour. The composition of the solutions changed in dependence on the knowledge of the composition of actual concentrates in the V-1 nuclear power plant at Jaslovske Bohunice. The following factors were studied in the concentrate: the effect of its pH, its borate content and content of metal carbonates, the content of organic acid salts, the content of detergents, etc., on the process of bituminization. Physico-chemical conditions are described under which the operation of the evaporator was fail-safe and filling of the bituminization product with salts homogeneous. A low water content of up to 1% was achieved. The properties of the bituminization product were negatively affected by a high level of heavy metal oxides, surfactants, oxalates and citrates. In order to improve the properties of the product it will be necessary to replace bitumen emulsion Silembit-60 used as reinforcement matrix, by a different type of bitumen. (Z.M.)

30 CFR 716.4 - Special bituminous coal mines.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Special bituminous coal mines. 716.4 Section... INTERIOR INITIAL PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.4 Special bituminous coal mines. (a) Definition. Special bituminous coal surface mines as used in this section means those bituminous...

Study of bituminous surface treatments in Virginia : Phase II, Summer, 1964 : Distribution characteristics of materials, effectiveness of one size aggregate, setting time.

Science.gov (United States)

1970-01-01

Distribution Characteristics of Materials: Ten bituminous distributors and ten chip spreading operations were investigated the former by cotton pad, cup, and trough tests; the latter by measuring the distance covered by a truckload and by placing pan...

Prediction of Marshall Parameters of Modified Bituminous Mixtures Using Artificial Intelligence Techniques

Directory of Open Access Journals (Sweden)

Sunil Khuntia

2014-09-01

Full Text Available This study presents the application of artificial neural networks (ANN and least square support vector machine (LS-SVM for prediction of Marshall parameters obtained from Marshall tests for waste polyethylene (PE modified bituminous mixtures. Waste polyethylene in the form of fibres processed from utilized milk packets has been used to modify the bituminous mixes in order to improve their engineering properties. Marshall tests were carried out on mix specimens with variations in polyethylene and bitumen contents. It has been observed that the addition of waste polyethylene results in the improvement of Marshall characteristics such as stability, flow value and air voids, used to evaluate a bituminous mix. The proposed neural network (NN model uses the quantities of ingredients used for preparation of Marshall specimens such as polyethylene, bitumen and aggregate in order to predict the Marshall stability, flow value and air voids obtained from the tests. Out of two techniques used, the NN based model is found to be compact, reliable and predictable when compared with LS-SVM model. A sensitivity analysis has been performed to identify the importance of the parameters considered.

Evaluating Self Healing Capability of Bituminous Mastics

NARCIS (Netherlands)

Qiu, J.; Van de Ven, M.; Wu, S.; Yu, J.; Molenaar, A.

2012-01-01

The self-healing capability of bituminous materials has been known for many years. Researches were mostly focused on the self healing behaviour during load repetitions. The tests are either time consuming and/or complex. In this paper, a simple self healing test procedure is presented combining the

Process for carbonization of bituminous combustibles

Energy Technology Data Exchange (ETDEWEB)

1923-02-02

A process for the carbonizing of bituminous materials is characterized in that the material is exposed to the action of radiant heat by insertion of a gas layer between the charge and the gasflames and at the same time to convection heating. The process spreads the material on a permeable support and by employing generator gases form the spent residue and if necessary also the permanent gases from the condenser for heating is characterized in that these gases are conducted directly over the material, and partly passed through it and partly burned over it by means of air.

Process for recovering oil from shale and other bituminous materials

Energy Technology Data Exchange (ETDEWEB)

1918-08-23

A process for recovering oil from shale and other bituminous minerals in rotary retorts heated from outside and flushed with water vapor or other oxygen-free gases is characterized by the fact that all kinds of minerals are carbonized, and that during the carbonization process the temperature of the superheated steam or gases is about 50/sup 0/ C higher than the temperature of the carbonized mineral.

Bituminization of low- and medium-level radioactive wastes

International Nuclear Information System (INIS)

Lefillatre, G.

1976-01-01

French operations are presented concerning mainly: the bituminization of radioactive wastes produced in light water reactors; the direct bituminization of liquid effluents without concentration; the experiments carried out for 18 months on the land burial of concentrates solidified by bitumen into blocks of 100 liters. The knowledge acquired in France is exposed: in Valduc and in Saclay with facilities equipped with thin film evaporators and in Marcoule with the conditioning of trilaurylamine and tributyl-phosphate. At last the Cadarache bituminization [fr

Distillation of bituminous substances

Energy Technology Data Exchange (ETDEWEB)

du Buisson, M A.B.B.

1845-06-23

New and improved methods are described for the distillation of bituminous schistus and other bituminous substances, as well as for the purification, rectification, and preparation necessary for the employment of the productions obtained by such distillation for various useful purposes. This invention consists, first, in the arrangement and construction of furnace or apparatus for the distillation of schistus, and (any) other bituminous rocks. This furnace is made of circular brick-work, and is provided with the requisite number of fires placed round the circumference. The retort is of a conical or funnel shape, and when ready for use, has the appearance of one inverted cone being placed within a larger cone, in such a manner as to leave a space between the two cones for the reception of the schistus. Both cones are capable of being closed at their apexes, and their mouths, which are placed upwards, are connected together, and hermetically closed by a flat ring. The flame draft is caused to impinge against the lower portion of the outer cone and ascending, turns over the upper edge and descends within the inner cone to the mouth of the chimney, which is placed in the interior, and as low as may be convenient. A third cone is so placed within the inner cone as to cause the flame draft, in its descent, to bind against the surface of the retort.

Response Modelling of Bitumen, Bituminous Mastic and Mortar

NARCIS (Netherlands)

Woldekidan, M.F.

2011-01-01

This research focuses on testing and modelling the viscoelastic response of bituminous binders. The main goal is to find an appropriate response model for bituminous binders. The desired model should allow implementation into numerical environments such as ABAQUS. On the basis of such numerical

Long-term properties of bituminized waste products

International Nuclear Information System (INIS)

Snellman, M.; Valkiainen, M.

1985-10-01

This study is a survey of the factors of importance for the long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are related to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product

Long-term properties of bituminized waste products

International Nuclear Information System (INIS)

Snellman, M.; Valkiainen, M.

1985-10-01

This study is a survey of the factors of importance for long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are ralated to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product. (author)

Crumb Rubber in cold recycled bituminous mixes

DEFF Research Database (Denmark)

Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo

2014-01-01

Today recycling is one of the most innovative and interesting techniques for the rehabilitation of destressed road pavements. In recent years the increased interest in this process, has led to the development of various alternative methods for the recovery and the reuse of road bituminous materials...

Process for treating bituminous coal, lignite, peat, and shale, and products obtained

Energy Technology Data Exchange (ETDEWEB)

Schabelitz, E J

1951-06-27

A process is described comprising leaching bituminous coal, lignite, peat, or shale by immersing said material in ethylene dichloride for a period of time sufficient to remove the ethylene dichloride-soluble constituents, separating the treated material from the ethylene dichloride solution and recovering from the solution the soluble constituents of the material dissolved in the solution. Soluble constituents include oils and waxes.

Apparatus for carbonizing bituminous substances, etc

Energy Technology Data Exchange (ETDEWEB)

Meguin, A G

1921-06-24

A process is disclosed of carbonizing bituminous substances such as coal, or shale, at a low temperature, the distinguishing feature being that during the gas-distillation period, the material is subjected to centrifugal action in a rotary drum or retort is distributed over the whole circumference of the drum and is at the same time compressed.

Leachability of bituminized radioactive waste. Literature survey

International Nuclear Information System (INIS)

Akimoto, Toshiyuki; Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi

1999-02-01

Bituminized radioactive waste that will be returned from COGEMA, France is planned to be disposed of in deep geologic repository in Japan. Data on leachability of radionuclides from bituminized waste are required for the performance assessment of the disposal. We made a literature survey on bitumen and bituminized radioactive waste, placing emphasis on leach tests and leach data in terms of geologic disposal. This survey revealed that reliable leach data on transuranium elements and data obtained under reducing conditions that is characteristic to deep underground are lacking. (author). 64 refs

Evaluation of bituminous sub-ballast manufactured at low temperatures as an alternative for the construction of more sustainable railway structures

Directory of Open Access Journals (Sweden)

L. Pirozzolo

2017-07-01

Full Text Available Hot bituminous mixtures are becoming widely used in modern railway tracks in the sub-ballast layer. The reason is that these materials allow for both an increase in bearing capacity and greater protection of the substructure respect the traditional granular sub-ballast. Despite these advantages, the fact that these materials are manufactured at a temperature of 160°C means that their application can lead to an important increase in construction costs, pollution and energy consumption. This paper aims to study the possibility of using WMA manufactured at lower temperatures, as bituminous sub-ballast, in order to save energy and reduce emissions throughout the production process, as well as diminish the global costs of this layer. To this end, this study focuses on a comparison of the mechanical behaviour of warm and hot bituminous mixtures as sub-ballast under various loading conditions. The results indicate that WMA offers mechanical behaviour that is comparable to conventional HMA.

Evaluation of bituminized waste reactivity

International Nuclear Information System (INIS)

Camaro, S.; Moulinier, D.

2000-01-01

The bituminization process has been used for conditioning low and medium level (LML) radioactive waste, particularly to immobilize coprecipitation slurries and evaporation concentrates generated by effluent treatment. The process consists in mixing bitumen matrix with inactive soluble and slightly soluble salts added to insolubilize the radionuclides or resulting from the neutralization of acid effluents. This operation is performed at a sufficient temperature - depending on waste composition and bitumen grade to ensure the flow of the resulting mixture into metal containers. Exothermicity due to salts/salts or salts/bitumen reactions depending on the type of waste can be induced during or after the mixing step. This could produce an additional heat emission that the drum must be able to release to avoid a potentially incidental pattern with ignition risk, explaining why the CEA has been involved in evaluating the thermal reactivity of bituminized waste and its repercussions on the bituminization process. Given the difficulty of discriminating each exothermal reaction, the characterization of a global reactivity appears as a further precautionary measure, in addition to the definition of a working safety margin. The CEA has accordingly developed studies on this aspect. The article discusses the experimental methodology developed for the determination of the global reactivity. (authors)

Bituminization of liquid radioactive wastes. Part 1

International Nuclear Information System (INIS)

Gradev, G.D.; Ivanov, V.I.; Stefanova, I.G.; Milusheva, A.G.; Guteva, E.S.; Zhelyazkov, V.T.; Stefanov, G.I.; G'oshev, G.S.

1991-01-01

Salt-bitumen products are produced by the method of 'hot mixing' of some Bulgarian bitumens (road bitumen PB 66/99 and the hydroinsulating bitumen HB 80/25) and salts (chlorides, sulphates, borates, salt mixtures modelling the liquid waste from nuclear power plants) in different ratios to determine the optimum conditions for bituminization of liquid radioactive waste. The penetration, ductility and softening temperature were determined. The sedimentation properties and the thermal resistance of the various bitumen-salt mixtures were studied. The most suitable bitumen for technological research at the Kozloduy NPP was found to be the road bitumen PB 66/90 with softening temperature at 48 o C. The optimum amount of salts incorporated in the bitumen - about 45% - was found. No exothermal effects were observed in the bituminization process in the temperature range of up to 200 o C. The results obtained may be useful in the elaboration of a technology for bituminization of liquid radioactive wastes in the Kozloduy NPP. 4 tabs., 5 figs., 4 refs

FY 1991 report on the bituminous coal liquefaction section; 1991 nendo rekiseitan ekikabukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

The paper reported activities of the bituminous coal liquefaction section in FY 1991. In the 1st bituminous coal liquefaction section meeting, report/discussion were made on the outline of the plan on the FY 1991 research using pilot plant and the support study of pilot plant. In the 2nd section meeting, report was made on 'How the development of coal liquefaction technology should be in the 21st century,' a report made by the joint section of bituminous coal/brown coal liquefaction. In the 3rd section meeting, report/discussion were made on the state of progress of the FY 1991 R and D and results. In the study using the bituminous coal liquefaction pilot plant, report was made on the outline of construction of a 150t/d pilot plant, study on the acquisition of material balance, analytical study of the data on liquefaction tower, testing survey on properties of coal slurry, and testing survey on slurry preheating furnace. In the support study of pilot plant, report was made on the study using 1t/d PUS, study on the development of the optimum coal refining technology and improvement in the distillate distribution, study of conditions for coal liquefaction and study of solvent hydrogenation catalyst. (NEDO)

Apparatus for treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

1942-11-24

A method is given of transforming finely crushed bituminous shale, for instance of maximum particle size of about 5 mm, into balls, nodules, or similar shapes, in which the shale to be treated is passed in the form of lumps through a rotary drum. The finely crushed shale with a higher content of moisture is brought into contact with finely crushed shale of a lower content of moisture, and thereby serves as kernel material during the formation of the nodules or similar shapes.

On inflammability and explosiveness in bituminization

International Nuclear Information System (INIS)

Zakharova, K.P.; Kulichenko, V.V.; Nazin, E.R.; Sadovnikov, Yu.N.; Ukke, O.V.

1978-01-01

Results of a study of safety in the bituminization of radioactive wastes and storage of the final product are presented. The temperature of interaction of bitumen with one of the basic waste components, i.e. sodium nitrate, is 385-408 deg C. A noticeable decrease in this value is observed only in the presence of an alkali. The introduction of an additive in bitumen does not increase its inflammability as measured by a number of indicators. Bituminous substances containing less than 15% bitumen are capable of detonating, while those with a higer percentage are not

Use of additives to improve the capacity of bituminous mixtures to be heated by means of microwaves

International Nuclear Information System (INIS)

Gallego, J.; Val, M.A. del; Contreras, V.; Páez, A.

2017-01-01

This study examines the potential of adding electric arc furnace slag to bituminous mixtures to be heated by microwaves. The susceptibility of bituminous mixtures to microwave energy is limited and so, in order to improve the energy performance of the heating process, it is necessary to incorporate additives or components to the mixture so as to improve the capacity for microwave heating. The article presents the results of adding various components, (steel wool, scrap tire wire, silicon carbide, iron filings) and an alternative aggregate: electric arc furnace slag. According to the results obtained in the laboratory, slag addition of at least 5% by weight of the bituminous mixture represents the best option for both technical and economic reasons. The results may promote the valorization of this steel industry residue in bituminous mixtures by improving microwave heating response. [es

Development of bituminization process for radioactive wastes

International Nuclear Information System (INIS)

Segawa, Takeshi; Yamamoto, Masao; Miyao, Hidehiko; Mizuno, Ryukichi

1973-01-01

For the bituminization of radioactive wastes from a fuel reprocessing plant, the leachability, irradiation stability and burning property of bitumen products have been studied. Sodium nitrate was used for simulated evaporator concentrate, and mixed with distillation bitumen or blown bitumen; the sodium nitrate content in the mixture was 30 to 60 wt%. The distillation bitumen is superior to the blown bitumen in leachability and flash point, but inferior in the increase of volume by irradiation. Since the volume increase is not large, the distillation bitumen is satisfactory for the bituminization of the evaporator concentrate from a fuel reprocessing plant. (Mori, K.)

Technological research of bituminization of model concentrates of radioactive wastes

International Nuclear Information System (INIS)

Breza, M.; Timulak, J.; Krejci, F.; Pekar, A.; Krajc, T.; Hladky, E.

1986-01-01

In the years 1981-1984 research was carried out of bituminization technology on model concentrates whose physical and chemical composition approximated that of radioactive concentrates from WWER-440 type nuclear power plants. The bitumen emulsion Silembit EAS-60 was used for bituminization. The process of bituminization took place at a temperature of approximately 180 degC in a rotary film evaporator into which was proportioned both the model concentrate and the bitumen emulsion heated to a temperature of 50 to 60 degC. All basic technical parameters of the process were controlled on an hourly basis. The experiments demonstrated the following technological conditions of bituminization: pressure of heating steam must be maintained within 0.85 and 0.95 MPa; optimal output of the evaporator (type FRO-2 S) is 100 to 120 kg of evaporated water/h; concentrates with a borate content must be heated to a temperature of 80 to 90 degC prior to their introduction into the evaporator; the pH value of the concentrates must be adjusted such as to be within the range of 11.0 to 11.5 or 7.0 to 8.0; the concentrate and the bitumen emulsion must be proportioned evenly; the optimal speed of the rotor is 500 r.p.m.; the load of the rotor must be monitored continuously because it indicates changes in the flow values of the bitumen composition. The experience gained was used in the operation of the pilot plant bituminization line for actual concentrates from the V-1 nuclear power plant. (A.K.)

Evaluation of mastic in bituminous mixtures

OpenAIRE

Silva, Hugo Manuel Ribeiro Dias da; Pais, Jorge C.; Pereira, Paulo A. A.

2002-01-01

The efficiency of the asphalt-aggregate bond is one of the key factors which affects the mechanical resistance of bituminous mixtures and a better understanding of its performance allows the behaviour of mixture to be more accurately predicted. The asphalt-aggregate bond depends on the properties of the mastic and the mixture of fine aggregate and bitumen which bonds itself to the larger sized particles within the bituminous mixture. This mastic plays an im-portant role in the asphalt-aggr...

Utilization of Waste Clay from Boron Production in Bituminous Geosynthetic Barrier (GBR-B Production as Landfill Liner

Directory of Open Access Journals (Sweden)

Müfide Banar

2016-01-01

Full Text Available Bituminous geomembranes, one type of geosynthetics, include a hot bituminous mixture with mineral filler and reinforcement. In this study, boron production waste clay (CW was used as filler to produce a geosynthetic barrier with bentonite, waste tire, and bitumen. Bentonite and waste tires were used as auxiliary fillers and bitumen as the binder. CW/bitumen, CW/bentonite/bitumen, and CW/waste tire/bitumen mixtures were prepared by using a laboratory mixer at 100°C. Hot mixtures were extruded into strips by using a lab-scale corotating twin screw extruder (L/D: 40 followed by die casting (2 mm × 100 mm. Glass fleece or nonwoven polyester was used as reinforcement material and while die casting, both sides of the reinforcement materials were covered with bituminous mixture. Thickness, mass per unit area, tensile strength, elongation at yield, and hydraulic conductivity were used to characterize the geomembranes. Among all geomembranes, nonwoven polyester covered with 30% bitumen-70% boron waste clay mixture (PK-BTM30CW70 was found to be the most promising in terms of structure and mechanical behaviour. After that, consequences of its exposure to distilled water (DW, municipal solid waste landfill leachate (L-MSW, and hazardous waste landfill leachate (L-HW were examined to use for an innovative impermeable liner on solid waste landfills.

Investigation and analytical results of bituminized products in drums at filing room

International Nuclear Information System (INIS)

Shibata, Atsuhiro; Kato, Yoshiyuki; Sano, Yuichi; Kitajima, Takafumi; Fujita, Hideto

1999-09-01

This report describes the results of investigation of the bituminized products in drums, liquid waste in the receiving tank V21 and the bituminized mixture in the extruder. The investigation of the products in drums showed most of the unburned products filled after 28B had abnormality, such as hardened surfaces, caves and porous brittle products. The particle sizes of the salt fixed in bituminized products depended neither on batch number nor on feed rate. It indicates the fining of the salt particle caused by the decreased feed rate did not occur. The measured concentrations of metals and anions in the bituminized products showed no abnormality. The catalytic content was not recognized in the products. The infrared absorption spectra obtained with the bituminized products show the oxidation at the incident occurred without oxygen. There was no organic phase on the surface of liquid waste in V21. Chemical analysis and thermal analysis on the precipitate in V21 showed no abnormality. Concentration of sodium nitrate/nitrite in the mixture collected from the extruder was lower than normal products. These results show no chemical activation of the bituminized products. It can be concluded that the chemical characteristics of the products had little abnormality even around the incident. (author)

INVESTIGATION ON UTILITY OF PLASTIC WASTE AS AN ADDITIVE FOR BITUMINOUS CONCRETE USING WET PROCESS OF MIXING

Directory of Open Access Journals (Sweden)

Anurag Virendra Tiwari

2017-12-01

Full Text Available Purpose. Plastic waste has become a major environmental issue of concern due to its exponential growth due to rapid urbanization. The paper investigates utility of plastic waste as an additive for bituminous concrete using wet process of mixing. Methodology. The methodology for the present paper has been designed with complex research consisting of Marshall mix design of the bituminous mix added with plastic waste for modifying bitumen using wet process of mixing, performing the tests on the samples and analyzing the results in the form of table and figures. In the present paper LDPE and HDPE type of plastic waste are used to modify the bitumen. Finding. The results show that addition of 6 percent of bitumen improves the Marshall properties of the mix. Use of plastic to modify the bitumen not only makes the road surface more durable but also it is an eco-friendly way of proper disposal of plastic waste. Originality. The processes used for mixing the plastic waste to the bitumen are dry process and wet process. Dry process of mixing the plastic waste to the bituminous mix is most common and lot of study is carried out on its application. In the present paper wet process of mixing has not yet been studied much. Practical Value. The practical application of utilizing the plastic waste to modify bitumen in the bituminous mix improves the stability values resulting in the more durable road surface. Also the method ensures the proper disposal of plastic waste in eco-friendly way.

Bituminization plant Jaslovske Bohunice

International Nuclear Information System (INIS)

1999-01-01

In this leaflet the principle of the bituminization plant for radioactive concentrate (the intermediate liquid radioactive waste generated during the NPP A1, V-1, V-2 operations) solidification used in the Bohunice Radwaste Treatment Centre (BSC RAO) is presented

Process and apparatus for distilling bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

Veyrier, J A

1922-03-27

This process of distillation of bituminous minerals and particularly bituminous limestone is characterized by the fact that the minerals are introduced into the retort where they stand only the temperature necessary to distill the water and lighter oils that they contain and then are drawn out into the hearth and serve for heating the retort. The apparatus is characterized by the fact that the retort has a screw conveyor, placed in the flue of the hearth, supplied with a chamber for evacuation below this hearth.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

Energy Technology Data Exchange (ETDEWEB)

Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Braet, Johan, E-mail: johan.braet@uantwerpen.be [Department Engineering Management, Faculty of Applied Economics, University of Antwerp, Prinsstraat 13, 2000 Antwerp (Belgium)

2016-09-15

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

International Nuclear Information System (INIS)

Anthonissen, Joke; Van den bergh, Wim; Braet, Johan

2016-01-01

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach

NARCIS (Netherlands)

Sourty, E.; Tamminga, A.Y.; Michels, M.A.J.; Vellinga, W.P.; Meijer, H.E.H.

2011-01-01

Selected carbon-rich refinery residues (‘binders’) mixed with mineral particles can form composite materials (‘bituminous concrete’) with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related

Adsorption of SO2 on bituminous coal char and activated carbon fiber prepared from phenol formaldehyde

Science.gov (United States)

DeBarr, Joseph A.; Lizzio, Anthony A.; Daley, Michael A.

1996-01-01

Carbon-based materials are used commercially to remove SO2 from coal combustion flue gases. Historically, these materials have consisted of granular activated carbons prepared from lignite or bituminous coal. Recent studies have reported that activated carbon fibers (ACFs) may have potential in this application due to their relatively high SO2 adsorption capacity. In this paper, a comparison of SO2 adsorption for both coal-based carbons and ACFs is presented, as well as ideas on carbon properties that may influence SO2 adsorption

Influence of association of "EVA-NBR" on indirect tensile strength of modified bituminous concrete

Science.gov (United States)

Chinoun, M.; Soudani, K.; Haddadi, S.

2016-04-01

The aim of this work is to contribute to the improvement of the mechanical properties of bituminous concrete by modification of bituminous concrete. In this study, we present the results of the indirect tensile strength "ITS" of modified bituminous concrete by the combination of two modifiers, one is a plastomer EVA (Ethylene Vinyl Acetate) and the other is a industrial waste from the shoe soles grinding NBR (Nitrile Butadiene Rubber) as crumb rubber. To modify the bitumen a wet process was used. The results show that the modification of bitumen by EVA-NBR combination increases their resistance to the indirect traction "ITS" compared to the bituminous concrete control. The mixture of 5% [50% EVA+ 50% NBR] is given the best result among the other associations.

Environmental problems caused by bituminous schist and possible solutions

International Nuclear Information System (INIS)

Elmas, N.; Aykul, H.; Erarslan, K.; Ediz, I.G.

1998-01-01

Schist, as a disposal of mine, has harmful effects on environment. however, several manners can be utilized to prevent the environmental destruction as well as an economical benefit is gained. In this study, environmental problems caused by bituminous schist and other disposals have been investigated on a specific lignite coal mine where schist is disposed as waste material. Pollution and damage on land and in water sources around the coal district and the villages have been observed, recorded and several solutions to environmental problems have been proposed. Discussed proposals will not only solve the environmental pollution problem but also provide waste management facility. Industrial structure of the district enables such a disposal to be used as an economical raw material. Besides, general effects of the coal mine and the power plant nearby have been discussed from environmental point of view, too. 7 refs

Assessment of the Remaining Life of Bituminous Layers in Road Pavements

Directory of Open Access Journals (Sweden)

Kálmán Adorjányi

2017-02-01

Full Text Available In this paper, a mechanistic-empirical approach is presented for the assessment of bearing capacity condition of asphalt pavement layers by Falling Weight Deflectometer measurements and laboratory fatigue tests. The bearing capacity condition ratio was determined using past traffic data and the remaining fatigue life which was determined from multilayer pavement response model. The traffic growth rate was taken into account with finite arithmetic and geometric progressions. Fatigue resistance of layers’ bituminous materials was obtained with indirect tensile fatigue tests. Deduct curve of condition scores was derived with Weibull distribution.

Effect of asphaltene and resin oils on the viscosity of bituminous petroleum materials to be used as asphalt primers

Directory of Open Access Journals (Sweden)

Bencomo, M. R.

2006-03-01

Full Text Available The bituminous crude from the Machete, Venezuela, area, which has such a fluid consistency that it falls outside the normal scope of the A5TM D-5 (1 penetration test exceeding the 3D-mm ceiling specified in that standard and can be used as an asphalt primer: Like other asphalt products, these materials are -chemically speaking- a mix of numerous naphthenic, paraffinic and aromatic hydrocarbons and heterocyclic compounds containing sulphur, nitrogen, oxygen and so on. They have a dense and a malthene oil phase which, along with the natural hydrocarbons additives used in these products acts as a volatile fluidizer. The former is described as a mix of asphaltenes: complex high molecular weight substances that are insoluble in paraffinic hydrocarbons and soluble in aromatic compounds such as benzene. The malthene oil phase, in turn, consists in a mix of resins and hydrocarbons and together the two constitute a colloidal system. The experiments discussed in the present paper were conducted to determine the effect of the proportion of asphaltenes and resin oils on the viscosity of such bituminous crude emulsions/ with a view to their use as primers. These experiments were run in a Parr batch reactor in a nitrogen atmosphere using n-heptane as a solvent. The resins were separated after the asphaltenes precipitated from the samples and subsequently from the malthene fraction obtained. The results showed that the asphaltenes account for the structural characteristics and consistency of the medium and the resin oils for its cohesive properties/,the malthene oils act as solvents.Los crudos extrapesados procedentes del área Machete (Venezuela son materiales de consistencia blanda o fluida, por lo que se salen del campo en el que normalmente se aplica el ensayo de penetración a productos asfálticos según el método ASTM D-5 (1, cuyo límite máximo es 30 mm, y pueden ser utilizados como pinturas asfálticas de imprimación. Al igual que otros productos

Identification of aggregates for Tennessee bituminous surface courses

Science.gov (United States)

Sauter, Heather Jean

Tennessee road construction is a major venue for federal and state spending. Tax dollars each year go to the maintenance and construction of roads. One aspect of highway construction that affects the public is the safety of its state roads. There are many factors that affect the safety of a given road. One factor that was focused on in this research was the polish resistance capabilities of aggregates. Several pre-evaluation methods have been used in the laboratory to predict what will happen in a field situation. A new pre-evaluation method was invented that utilized AASHTO T 304 procedure upscaled to accommodate surface bituminous aggregates. This new method, called the Tennessee Terminal Textural Condition Method (T3CM), was approved by Tennessee Department of Transportation to be used as a pre-evaluation method on bituminous surface courses. It was proven to be operator insensitive, repeatable, and an accurate indication of particle shape and texture. Further research was needed to correlate pre-evaluation methods to the current field method, ASTM E 274-85 Locked Wheel Skid Trailer. In this research, twenty-five in-place bituminous projects and eight source evaluations were investigated. The information gathered would further validate the T3CM and find the pre-evaluation method that best predicted the field method. In addition, new sources of aggregates for bituminous surface courses were revealed. The results of this research have shown T3CM to be highly repeatable with an overall coefficient of variation of 0.26% for an eight sample repeatability test. It was the best correlated pre-evaluation method with the locked wheel skid trailer method giving an R2 value of 0.3946 and a Pearson coefficient of 0.710. Being able to predict field performance of aggregates prior to construction is a powerful tool capable of saving time, money, labor, and possibly lives.

Results of exploitation of a pilot-plant installation for bituminization of radioactive sludges

International Nuclear Information System (INIS)

Golinski, M.; Ksiazak, Z.; Surala, J.; Dziubecki, R.

1974-01-01

Results are discussed of exploitation of a pilot-plant installation for bituminization of radioactive sludges of an efficiency of 25 l/h. In a time period of 20 month 120 cycles were carried out in which 60 m 3 of 2-4% sludges from treatment of low-level waste by the phosphate-ferrocyanide method were solidified. The P-60 asphalt was used for bituminization. The bituminization products contained 5-13.5% of mineral substances. Their activity was in the range 5 x 10 -4 - 5 x 10 -3 μCi/g for alpha emitters and 1.2 - 3.8 x 10 -2 μCi/g for beta emitters. (author)

Effect of Mixing Process on Polypropylene Modified Bituminous Concrete Mix Properties

OpenAIRE

Noor Zainab Habib; Ibrahim Kamaruddin; Madzalan Napiah; Isa Mohd Tan

2011-01-01

This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely cont...

Solidification of radioactive wastes by bituminization technology. II

International Nuclear Information System (INIS)

Stuchlik, S.; Brzobohaty, J.

1985-01-01

The bituminization line consists of a rotor film evaporator, a condenser, reserve tanks of bitumen emulsion and model concentrates, a roller train, a vapour concentrate tank, a control console, a bitumen emulsion pump, a model concentrates pump, and a tank for model concentrate preparation. Anion-active emulsion Silembit S-60 produced by Paramo Pardubice was chosen as the bitumen emulsion. A block diagram is given of the experimental bituminization line and its processing is described of model nonactive concentrates whose composition corresponds to that of actual wastes from the V-1 nuclear power plant. Successful tests of the line showed that it could be used for the disposal of radioactive wastes. (E.S.)

Nitrogen-enriched bituminous coal-based active carbons as materials for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

R. Pietrzak; K. Jurewicz; P. Nowicki; K. Babel; H. Wachowska [A. Mickiewicz University, Poznan (Poland). Laboratory of Coal Chemistry and Technology

2010-11-15

The paper presents the results of a study on obtaining N-enriched active carbons from bituminous coal and on testing its use as an electrode material in supercapacitors. The coal was carbonised, activated with KOH and ammoxidised by a mixture of ammonia and air at the ratio 1:3 at 300{sup o}C or 350{sup o}C, at different stages of the production, that is, at those of precursor, carbonisate, and active carbon. The products were microporous N-enriched active carbon samples of well-developed surface area reaching from 1577 to 2510 m{sup 2}/g and containing 1.0 to 8.5 wt% of nitrogen. The XPS measurements have shown that in the active carbons enriched in nitrogen at the stage of precursor and at the stage of carbonisate, the dominant nitrogen species are the N-5 groups, while in the samples ammoxidised at the last stage of the treatment the dominant nitrogen species are the surface groups of imines and/or nitriles, probably accompanied by amines and amides. The paper reports the results of a comprehensive study of the effect of the structure and chemical composition of a series of active carbon samples of different properties on their capacity performance in water solutions of H{sub 2}SO{sub 4} or KOH, with the behaviour of positive and negative electrodes analysed separately. 33 refs., 7 figs., 8 tabs.

State of the art report on bituminized waste forms of radioactive wastes

International Nuclear Information System (INIS)

Kim, Tae Kook; Shon, Jong Sik; Kim, Kil Jeong; Lee, Kang Moo; Jung, In Ha

1998-03-01

In this report, research and development results on the bituminization of radioactive wastes are closely reviewed, especially those regarding waste treatment technologies, waste solidifying procedures and the characteristics of asphalt and solidified forms. A new concept of the bituminization method is suggested in this report which can improve the characteristics of solidified forms. Stable solid forms with high leach resistance, high thermal resistance and good compression strength were produced by the suggested bituminization method, in which spent polyethylene from agricultural farms was added. This report can help further research and development of improved bituminized forms of radioactive wastes that will maintain long term stabilities in disposal sites. (author). 59 refs., 19 tabs., 18 figs

Mechanical properties of hot bituminous mixes manufactured with recycled aggregate of Silestone® waste

Directory of Open Access Journals (Sweden)

Rubio, M. C.

2011-03-01

Full Text Available This article presents the results of a research project which analyzes the viability of incorporating waste material from decorative quartz solid surfacing in the manufacture of hot bituminous mixes. For this purpose, various bituminous mixes were manufactured with waste aggregate in different percentage. A set of tests were carried out that permitted the characterization of the mechanical behavior of these mixes. The results of these tests were similar to the results obtained when conventional mixes made from virgin quarry aggregate were tested. The results for moisture sensitivity as well as for wheel track rutting on mixes showed the optimal performance of this waste material even under very demanding traffic conditions. Laboratory studies showed that the use of this waste material in the manufacture of bituminous mixes is technically viable and can provide high-quality recycled aggregates at a very low cost, which can be used in the pavement of road.

Este artículo muestra los resultados de un proyecto de investigación que tiene por objeto analizar la viabilidad de incorporación de residuos procedentes de piedra decorativa en la fabricación de mezclas bituminosas en caliente. Para ello se fabricaron mezclas con áridos reciclados de residuos procedentes de piedra decorativa en distintos porcentajes, realizando un conjunto de ensayos que posibilitaron caracterizar el comportamiento mecánico de dichas mezclas. Los resultados obtenidos fueron similares a los de las mezclas convencionales fabricadas con áridos vírgenes procedentes de cantera. Los valores de resistencia conservada ante la acción del agua y deformación en pista, pusieron de manifiesto la aptitud del residuo incluso ante las condiciones de tráfico más exigentes. Los trabajos realizados en el laboratorio indican que la utilización del residuo en la fabricación de mezclas bituminosas es técnicamente viable, pudiendo obtenerse áridos reciclados de gran calidad y

Process of heat-treating fuels of a bituminous nature, such as shale

Energy Technology Data Exchange (ETDEWEB)

Bergh, S V

1927-11-25

A process is described of heat treating any kind of material of a bituminous nature usable as fuel, like shale, mineral coal, peat, etc., whereby the fuel undergoes in a retort or the like a distillation for recovering from it the total amount or the greatest part of gaseous or vaporous distillation products. The warm distillation residue is burned, characterized by the retorts, containing the fuel going through, being wholly or partly surrounded by materials to be heated. These materials and the warm distillation residue resulting from the distillation during the burning are moved forward independently one of the other.

The problem of extracting oil from bituminous rock

Energy Technology Data Exchange (ETDEWEB)

Liatifov, A.I.; Bagirov, M.K.; Shirinov, S.G.; Sokov, U.I.; Zhirnov, E.I.

1982-01-01

Results are given from experimental laboratory research on flushing bituminous sandstones using diesel or oil alkaline by-products as the flushing agent and a sodium silicate solution as the desensitization initiator for the rock.

Effects of graphite on rheological and conventional properties of bituminous binders

Directory of Open Access Journals (Sweden)

Yunus Erkuş

2017-07-01

Full Text Available In this study, the effects of graphite used for developing the rheological and conventional properties of bitumen were investigated using various bituminous binder tests. Penetration, softening point, rotational viscosity (RV, dynamic shear rheometer (DSR and bending beam rheometer (BBR tests were applied to bituminous binders modified with four different proportions of graphite by bitumen weight. The penetration values declined while softening point values increased with rising graphite content. While graphite induced 8 °C increases in mixing-compacting temperature by increasing the viscosity values, it also increased the rutting parameter. According to the BBR test, the deformation and stiffness values changed significantly with increasing graphite content, but the m-values did not change significantly. These results showed that graphite generally used for improving the thermal properties can improve to high temperature performance of mixtures. Keywords: Graphite, Bitumen, Conventional properties, Rheological properties

Recovery of asphalt from bituminous minerals

Energy Technology Data Exchange (ETDEWEB)

Jossinet, J

1881-12-31

A process is disclosed for the recovery of asphalt from bituminous minerals, consisting in that the mineral is extracted with mineral oil, which is recovered by distilling the raw asphalt and distilling the solution to obtain on the one hand the liquid oil contained in the raw asphalt for use in the extraction and on the other hand distilled asphalt.

The influence of student characteristics on the use of adaptive e-learning material

NARCIS (Netherlands)

Seters, van J.R.; Ossevoort, M.A.; Tramper, J.; Goedhart, M.J.

2012-01-01

Adaptive e-learning materials can help teachers to educate heterogeneous student groups. This study provides empirical data about the way academic students differ in their learning when using adaptive elearning materials. Ninety-four students participated in the study. We determined characteristics

High temperature solvent extraction of oil shale and bituminous coal using binary solvent mixtures

Energy Technology Data Exchange (ETDEWEB)

Goetz, G.K.E. [Lehrstuhl fuer Geologie, Geochemie und Lagerstaetten des Erdoels und der Kohle, RWTH Aachen (Germany)

1997-12-31

A high volatile bituminous coal from the Saar Basin and an oil shale from the Messel deposit, both Germany, were extracted with binary solvent mixtures using the Advanced Solvent Extraction method (ASE). Extraction temperature and pressure were kept at 100 C, respectively 150 C, and 20,7 MPa. After the heating phase (5 min) static extractions were performed with mixtures (v:v, 1:3) of methanol with toluene, respectively trichloromethane, for further 5 min. Extract yields were the same or on a higher level compared to those from classical soxhlet extractions (3 days) using the same solvents at 60 C. Comparing the results from ASE with those from supercritical fluid extraction (SFE) the extract yields were similar. Increasing the temperature in ASE releases more soluble organic matter from geological samples, because compounds with higher molecular weight and especially more polar substances were solubilized. But also an enhanced extraction efficiency resulted for aliphatic and aromatic hydrocarbons which are used as biomarkers in Organic Geochemistry. Application of thermochemolysis with tetraethylammonium hydroxide (TEAH) using pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) on the extraction residues shows clearly that at higher extraction temperatures minor amounts of free fatty acids or their methyl esters (original or produced by ASE) were trapped inside the pore systems of the oil shale or the bituminous coal. ASE offers a rapid and very efficient extraction method for geological samples reducing analysis time and costs for solvents. (orig.)

Biowaste utilization in the process of co-gasification with bituminous coal and lignite

International Nuclear Information System (INIS)

Howaniec, Natalia; Smoliński, Adam

2017-01-01

Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1986-01-01

The results of the study of simulated radwaste, spent ion-exchange resins, borates/evaporator-concentrates and animal ashes, in bituminized form, are presented and discussed. Distilled and oxidized bitumen were used for characterizing the crude material and simulated wastes-bitumen mixtures of varying weight composition 30, 40, 50, 60% by weight the dry waste material. The asphaltine and parafin contents in the bitumens were determined. Some additives and clays were used aiming best characteristics of solidified wastes. For leaching studies, granular ion-exchange resins were loaded with Cs 134 and mixtures of resins-bitumens were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. It was used a conventional screw-extruder, used in plastic industry, to determine operational conditions and process difficulties. Mixtures resins-bitumen and concentrate-bitumen in differents operational condition were prepared and analysed. (Author) [pt

The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach.

Science.gov (United States)

Sourty, E D; Tamminga, A Y; Michels, M A J; Vellinga, W-P; Meijer, H E H

2011-02-01

Selected carbon-rich refinery residues ('binders') mixed with mineral particles can form composite materials ('bituminous concrete') with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related to the appearance of a rigid percolating network consisting of asphaltenes and mineral particles [Wilbrink M. et al. (2005) Rigidity percolation in dispersions with a structured visco-elastic matrix. Phys. Rev. E71, 031402]. In this paper, we explore the microstructure of thin binder films of varying thickness with a number of microscopic characterization techniques, and attempt to relate the observed microstructure to the distinctive mechanical behaviour. Two binders, only one of which has been proven to be suitable for bituminous concrete were investigated, and their microstructure compared. Both binders show the formation of asphaltene aggregates. The binder suitable for bituminous concrete is distinguished by the fact that the asphaltenes show a stronger tendency towards such aggregation, due to a higher concentration and less stabilization in the maltene phase. They also show a clear affinity to other species (such as waxes) and may act as nucleation sites for crystals and aggregates of those species. © 2010 The Authors Journal compilation © 2010 The Royal Microscopical Society.

The influence of student characteristics on the use of adaptive e-learning material

NARCIS (Netherlands)

van Seters, J. R.; Ossevoort, M. A.; Tramper, J.; Goedhart, M. J.

Adaptive e-learning materials can help teachers to educate heterogeneous student groups. This study provides empirical data about the way academic students differ in their learning when using adaptive e-learning materials. Ninety-four students participated in the study. We determined characteristics

Application of the cementitious grouts on stability and durability of semi flexible bituminous mixtures

Science.gov (United States)

Karami, Muhammad

2017-11-01

This paper describes the results of laboratory test for a high durability semi flexible bituminous mixtures (SFBM). The SFBM consists of an open asphalt structure where a high strength mortar is penetrated into the air voids of the bituminous mixtures. The SFBM combines the cement concrete's strength and the asphalt material flexibility. The objective of this study is to involve in the determination of stability and durability of SFBM by located the position of the specimen on an exposed area for 7, 90, 180 and 240 days. The performance of the SFBM was assessed using Marshall and wheel tracking apparatus. Total 18 specimens were prepared and examined for both of test. The Marshall specimens were cylindrical with dimension of 10.16 cm in diameter and 6.35 cm in high. For wheel tracking test, the specimens consisted of slabs with dimension of 30 cm in length, 30 cm in width and 5 cm in height. The results indicated that the first durability index and second durability index increased significantly. For Marshall test, the first and second durability index increased about 0.9% per day and 52.3%, respectively. However, for wheel tracking test, the first and second durability index increased about 1.9% per day and 119%, respectively.

Biodegradation of bituminous products from processing liquid radioactive wastes

International Nuclear Information System (INIS)

Tibensky, L.; Krejci, F.; Hladky, E.; Halama, D.

1988-01-01

One of the possible ways of disturbing the stability of bituminous products from liquid radioactive waste processing, is biodegradation caused by common microorganisms. Pseudomonas bacteria and a Bacillus cereus culture were selected for experimental study of cultivation of microorganisms. Experiments with mixed cultures were also performed. Pitches, ajatin and imidazoline were used as inhibitors. The thin layer and the emulsion methods were used in assessing biological corrosion. The results of the experiments are discussed with respect to the dependence of bacterial growth on bitumen biodegradation, the effect of pH on bitumen degradation and the effect of inhibitors on bitumen biodegradation. The salts contained in bituminous products were not found to significantly affect the rate of destruction. The degree of degradation was found to mainly depend on the bitumen, its chemical composition, and on the conditions of storage. It was also found that inhibitor additions in some cases modified the properties of the matrix such that it became more liquid. The coefficient of extractibility thus increased of matrix salts. The recultivation of bacteria on a full-value medium resulted in the loss of the inhibitory effect. In some cases, the inhibitor even stimulated the growth of microorganisms. The use of inhibitors in an effort to achieve biostability of bituminous products thus did not solve the problem. (Z.M.). 2 tabs., 9 refs

Quality assurance program : bituminous concrete and central mix aggregates.

Science.gov (United States)

1980-01-01

This report presents the results of a pilot quality assurance program initiated in the Richmond District in 1978. Under this program the producer's control tests are used for the acceptance of central mix aggregate and bituminous concrete and the Dep...

Bituminization of radioactive wastes at the Nuclear Research Center Karlsruhe

International Nuclear Information System (INIS)

Hild, W.; Kluger, W.; Krause, H.

1976-05-01

A summary is given of the main operational experience gained at the Nuclear Research Center Karlsruhe in 4 years operation of the bituminization plant for evaporator concentrates from low- and medium level wastes. At the same time some of the essential results are compiled that have been obtained in the R + D activities on bituminization. (orig.) [de

Bituminous reference document: synthesis of knowledge on the long time behavior of bituminous packages; Dossier de reference bitume: synthese des connaissances sur le comportement a long terme des colis bitumes

Energy Technology Data Exchange (ETDEWEB)

Sercombe, J.; Adenot, F.; Vistoli, P.P.; Parraud, S.; Riglet-Martial, C.; Gwinner, B.; Felines, I.; Tiffreau, C.; Libert, M

2004-07-01

This document is a synthesis of the knowledge acquired at the CEA on the behavior of bituminous packages. In this framework, the CEA studied bituminous packages in generic conditions of a package lifetime. The main factors, the evolution mechanisms and influential parameters have been determined and quantitative s simulation have been developed. After a description of the main initial bituminous packages characterizations, the evolutions in saturated and un-saturated environment are exposed. (A.L.B.)

Behaviour of bituminized radioactive wastes under irradiation

International Nuclear Information System (INIS)

Camaro, S.; Gilardi, T.; Vistoli, P.P.

2000-01-01

Studies are carried out by the CEA in order to predict the behaviour of bituminized radioactive wastes under self irradiation. Bitumen radiolysis produces gas (mainly H 2 ) which diffuses in the organic matrix. If the hydrogen yield is higher than the diffusion flux through the free surface, hydrogen concentration increases and exceeds its solubility in bitumen. Beyond saturation, bubbles are formed and gas is also evacuated by bubbles drift. The aim of these studies is to evaluate the evacuation capacity of radiolytic gas produced in function of initial bituminized wasteform characteristics. A model was developed to achieve this purpose, by calculating the evolution of bubbles population considering all elementary mechanisms of gas evacuation. (authors)

Concentration of viruses from water on bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Lakhe, S.B.; Parhad, N.M.

1988-05-01

The potential of bituminous coal for adsorption of viruses, using poliovirus as a model, was investigated. Influence of pH of water on the adsorption of viruses on a coal bed with and without addition of cation (Al/sup 3 +/) indicated that poliovirus could be adsorbed efficiently at pH 5 in presence of AlCl/sub 3/ at a concentration of 0.0005 M. studies on the effect of different concentrations of monovalent, divalent and trivalent cations showed that the trivalent cation was more effective and was required at a lower concentration than other cations tested. A coal bed of 1.5 g could adsorb as high as 204,000 PFU from water based on the absence of virus in the filtrate. Total organic carbon content of the water did not interfere in virus adsorption to coal. The results obtained indicated that a bituminous coal bed could be used as one of the methods for efficient concentration of viruses from water. 31 refs., 8 tabs.

Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1987-01-01

The results of the study of bituminization of simulated radwaste - spennt ion-exchange resins, borate evaporator/concentrates and animal ashes, are presented and discussed. Distilled and oxidizer bitumen were used. Characterization of the crude material and simulated wastes-bitumen mixtures of varying weigt composition (30, 40, 50, 60% by weight of dry waste material) was carried out. The asphaltene and parafin contents in the bitumens were also determined. Some additives and were used with an aim to improve the characteristcs of solidified wastes. For leaching studies, granular ion-exchange resins were with Cs - 134 and mixtures of resin-bitumen were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. A conventional screw-extruder, common in plastic industry, was used determine operational parameters and process difficulties. Mixtures of resin-bitumen and evaporator concentrate-bitumen obtained from differents operational conditions were characterized. (Author) [pt

Using bamboo (Bambusa vulgaris) as a field drainage material in ...

African Journals Online (AJOL)

user

shaped ceramic tile, circular clay tile, concrete tile, bituminized fibre perforated pipe, perforated smooth plastic pipe to corrugated plastic pipe. Currently, corrugated pipes are frequently used, although clay and concrete pipes are still being used as well. The use of drainage pipes made of various assorted materials is.

Pre-treatment of bituminized NPP wastes for disposal in near-surface repository

Energy Technology Data Exchange (ETDEWEB)

Vieira, Vanessa Mota; Tello, Clédola Cássia Oliveira de, E-mail: vanessamotavieira@gmail.com, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The implementation of the national repository is an important technical requirement, and a legal requirement for the entry into operation of the nuclear power plant Angra 3. The Brazilian repository is being planned to be a near-surface one. In Brazil the low and intermediate level radioactive wastes are immobilized using cement and bitumen for Angra 1 and Angra 2 NPP, respectively. The main problems due to the disposal of bituminized wastes in repositories are swelling of the waste products and their degradation in the long term. To accommodate the swelling of the bituminized wastes, the drums are filled up to 70 - 90% of their volume, which reduces the structural the repository stability and the disposal availability. Countries, which use bitumen in the solidification of NPP's radioactive waste and have near-surface repositories, need to immobilize this bituminized waste within other drums containing cement pastes or mortars to disposal them. This study aims to find solutions for the storage in surface repository of bituminized radioactive waste products, making them compatible with the acceptance criteria of cemented waste products. It was also performed a modeling with the results obtained in the leaching test using the ALT program and defined the transport model of the cesium leachate element and it was verified that in the early times the leaching was governed by the diffusion model and later by the partition model. The results obtained in this study can be used in the evaluation of performance of repositories. (author)

Pre-treatment of bituminized NPP wastes for disposal in near-surface repository

International Nuclear Information System (INIS)

Vieira, Vanessa Mota; Tello, Clédola Cássia Oliveira de

2017-01-01

The implementation of the national repository is an important technical requirement, and a legal requirement for the entry into operation of the nuclear power plant Angra 3. The Brazilian repository is being planned to be a near-surface one. In Brazil the low and intermediate level radioactive wastes are immobilized using cement and bitumen for Angra 1 and Angra 2 NPP, respectively. The main problems due to the disposal of bituminized wastes in repositories are swelling of the waste products and their degradation in the long term. To accommodate the swelling of the bituminized wastes, the drums are filled up to 70 - 90% of their volume, which reduces the structural the repository stability and the disposal availability. Countries, which use bitumen in the solidification of NPP's radioactive waste and have near-surface repositories, need to immobilize this bituminized waste within other drums containing cement pastes or mortars to disposal them. This study aims to find solutions for the storage in surface repository of bituminized radioactive waste products, making them compatible with the acceptance criteria of cemented waste products. It was also performed a modeling with the results obtained in the leaching test using the ALT program and defined the transport model of the cesium leachate element and it was verified that in the early times the leaching was governed by the diffusion model and later by the partition model. The results obtained in this study can be used in the evaluation of performance of repositories. (author)

Rutting performance of cold bituminous emulsion mixtures

Science.gov (United States)

Arshad, Ahmad Kamil; Ali, Noor Azilatom; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

2017-10-01

Cold Bituminous Emulsion Mixture (CBEM) is an environmentally friendly alternative to hot mix asphalt (HMA) for road surfacing, due to its low energy requirements. However, CBEM has generally been perceived to be less superior in performance, compared to HMA. This paper details a laboratory study on the rutting performance of CBEM. The main objective of this study is to determine the Marshall properties of CBEM and to evaluate the rutting performance. The effect of cement in CBEM was also evaluated in this study. The specimens were prepared using Marshall Mix Design Method and rutting performance was evaluated using the Asphalt Pavement Analyzer (APA). Marshall Properties were analysed to confirm compliance with the PWD Malaysia's specification requirements. The rutting performance for specimens with cement was also found to perform better than specimens without cement. It can be concluded that Cold Bituminous Emulsion Mixtures (CBEM) with cement is a viable alternative to Hot Mix Asphalt (HMA) as their Marshall Properties and performance obtained from this study meets the requirements of the specifications. It is recommended that further study be conducted on CBEM for other performance criteria such as moisture susceptibility and fatigue.

Active materials for adaptive architectural envelopes based on plant adaptation principles

Directory of Open Access Journals (Sweden)

Marlen Lopez

2015-06-01

Full Text Available In this paper, the authors present research into adaptive architectural envelopes that adapt to environmental changes using active materials, as a result of application of biomimetic principles from plants to architecture. Buildings use large amounts of energy in order to maintain their internal comfort, because conventional buildings are designed to provide a static design solution. Most of the current solutions for facades are not designed for optimum adaptation to contextual issues and needs, while biological solutions to adaptation are often complex, multi-functional and highly responsive. We focus on plant adaptations to the environment, as, due to their immobility, they have developed special means of protection against weather changing conditions. Furthermore, recent developments in new technologies are allowing the possibility to transfer these plant adaptation strategies to technical implementation. These technologies include: multi-material 3D printing, advances in materials science and new capabilities in simulation software. Unlike traditional mechanical activation used for dynamic systems in kinetic facades, adaptive architectural envelopes require no complex electronics, sensors, or actuators. The paper proposes a research of the relationship that can be developed between active materials and environmental issues in order to propose innovative and low-tech design strategies to achieve living envelopes according to plant adaptation principles.  

Bituminous sands : tax issues

International Nuclear Information System (INIS)

Patel, B.

2004-01-01

This paper examined some of the tax issues associated with the production of bitumen or synthetic crude oil from oil sands. The oil sands deposits in Alberta are gaining more attention as the supplies of conventional oil in Canada decline. The oil sands reserves located in the Athabasca, Cold Lake and Peace River areas contain about 2.5 trillion barrels of highly viscous hydrocarbons called bitumen, of which nearly 315 billion barrels are recoverable with current technology. The extraction method varies for each geographic area, and even within zones and reservoirs. The two most common extraction methods are surface mining and in-situ extraction such as cyclic steam stimulation (CSS); low pressure steam flood; pressure cycle steam drive; steam assisted gravity drainage (SAGD); hot water flooding; and, fire flood. This paper also discussed the following general tax issues: bituminous sands definition; bituminous sands leases and Canadian development expense versus Canadian oil and gas property expense (COGPE); Canadian exploration expense (CEE) for surface mining versus in-situ methods; additional capital cost allowance; and, scientific research and experimental development (SR and ED). 15 refs

Losses due to weather phenomena in the bituminous concrete construction industry in Wisconsin

Science.gov (United States)

Kuhn, H. A. J.

1973-01-01

The losses (costs) due to weather phenomena as they affect the bituminous concrete industry in Wisconsin were studied. The bituminous concrete industry's response to precipitation, in the form of rain, is identified through the use of a model, albeit crude, which identifies a typical industry decision-response mechanism. Using this mechanism, historical weather data and 1969 construction activity, dollar losses resulting from rain occurrences were developed.

Framework for replacing steel with aluminum fibers in bituminous mixes

NARCIS (Netherlands)

Pavlatos, N.; Apostolidis, P.; Scarpas, Athanasios

2018-01-01

This research explores the incentives for replacing steel fibers with aluminum fibers in fiber modified bituminous mixes. In this work the focus is on fiber modified bituminous mixes especially designed for induction heating. Inductive fibers are heated up because eddy currents are generated -

MECHANICAL BEHAVIOR OF COLD BITUMINOUS MIXTURE UNDER EFFECTS OF STATIC AND REPEATED LOADS1

OpenAIRE

Tamyres Karla da Silva; Carlos Alexandre Braz de Carvalho; Geraldo Luciano de Oliveira Marques; Dario Cardoso de Lima; Taciano Oliveira da Silva; Carlos Cardoso Machado

2017-01-01

Abstract This paper presents the results of an experimental research aimed at analyzing the mechanical behavior of a cold bituminous mixture under effects of static and repeated loads. Initially, a Marshall mixture design was performed to determine the mixture design contents according to standard DNER (1994a). After obtaining the mixture design contents, nine bituminous specimens were molded and subjected to the following tests: resilient modulus, tensile strength by diametral compression, a...

Process for continuous distillation of bituminous minerals, etc

Energy Technology Data Exchange (ETDEWEB)

Marie, J J

1923-01-26

An apparatus is described for operating the process, in which the petroleum-bearing asphaltic or bituminous minerals are charged to the upper part of a vertical furnace with a lining of refractory material and varying sections; air is necessary for combustion and inert gas is necessary to regulate this combustion and to remove the hydrocarbons being blown into the lower part of the furnace; the hydrocarbons in vapor state or gases being removed are received in the condensers where they are deposited in the liquid state; the liquid from the condensers is next centrifuged to give oils essentially like natural petroleum, leaving as residue solid hydrocarbons and entrained mineral; the minerals treated are removed by gravity at the bottom of the furnace.

Leaching behavior of a simulated bituminized radioactive waste form under deep geological conditions

International Nuclear Information System (INIS)

Nakayama, Shinichi; Iida, Yoshihisa; Nagano, Tetsushi; Akimoto, Toshiyuki

2003-01-01

The leaching behavior of a simulated bituminized waste form was studied to acquire data for the performance assessment of the geologic disposal of bituminized radioactive waste. Laboratory-scale leaching tests were performed for radioactive and non-radioactive waste specimens simulating bituminized waste of a French reprocessing company, COGEMA. The simulated waste was contacted with deionized water, an alkaline solution (0.03-mol/l KOH), and a saline solution (0.5-mol/l KCl) under atmospheric and anoxic conditions. The concentrations of Na, Ba, Cs, Sr, Np, Pu, NO 3 , SO 4 and I in the leachates were determined. Swelling of the bituminized waste progressed in deionized water and KOH. The release of the soluble components, Na and Cs, was enhanced by the swelling, and considered to be diffusion-controlled in the swelled layers of the specimens. The release of sparingly soluble components such as Ba and Np was solubility-limited in addition to the progression of leaching. Neptunium, a redox-sensitive element, showed a distinct difference in release between anoxic and atmospheric conditions. The elemental release from the bituminized waste specimens leached in the KCl was very low, which is likely due to the suppression of swelling of the specimens at high ionic strength. (author)

Inductive bituminous mortar with steel and aluminum fibers

NARCIS (Netherlands)

Pavlatos, N.; Apostolidis, P.; Scarpas, Athanasios; Liu, X.; van de Ven, M.F.C.

2018-01-01

This research presents the implementation of a finite element model analysis for assessing the potential of utilizing alternative fibers for the development of inductive bituminous mixes with lower total weight, higher resistance against corrosion, and sufficient induction heating efficiency.

Carbonization process for bituminous shale, etc

Energy Technology Data Exchange (ETDEWEB)

1917-11-08

A process for uninterrupted carbonization with possibly greater yield of primary products and subsequent burning of the bituminous shale and other material with preponderantly inorganic constituents through direct flushing-through of the gases is characterized by a rustless shaft furnace wider at the bottom with lower inlets for air through the hot residue and air or gas inlets into the burning zone for the purpose of levelling the burning zone on one hand and regulating it in a determined cross section, and on the other hand to make possible ready determination of the temperature of the burning zone, the requisite means (vapor, wet or dry-air, air-hot gas mixture) going into the shaftcasing in the cross section in which the burning zone should be regulated, through an annular movable and double-sided coolable slit.

Properties of bituminization product from Olkiluoto power plant

International Nuclear Information System (INIS)

Valkiainen, M.; Vuorinen, U.

1985-09-01

In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

Treating bituminous shale

Energy Technology Data Exchange (ETDEWEB)

Ginet, J H

1921-03-09

Apparatus for the treatment of bituminous shales is described wherein a number of separate compartments are arranged in alignment and communicate with each other near the bottom thereof, each of the compartments being provided with outlets for the gases evolved therein, while agitators are arranged in each of the compartments, each agitator being composed of a number of shovels which sweep up the comminuted shale at their forward end and discharge it at their rearward end into the path of the next adjacent agitator.

Towards more efficient e-learning, intelligence and adapted teaching material

Directory of Open Access Journals (Sweden)

Damir Kalpić

2010-12-01

Full Text Available This article presents results of a research project in which we attempted to determine the relationship between efficient E-learning and teaching materials adapted based on students’ structure of intelligence. The project was conducted on approximately 500 students, 23 classes, nine elementary schools, with ten teachers of history, informatics and several licensed psychologists. E-teaching material was prepared for the subject of History for eight-grade students of elementary school. Students were tested for the structure of intelligence, and based on their most prominent component, they were divided into groups, using teaching materials adapted to their most prominent intelligence component. The results have shown that use of the adapted teaching materials achieved 6-12% better results than E-materials not adapted to students’ structure of intelligence.

Research on the thermal decomposition of Mongolian Baganuur lignite and Naryn sukhait bituminous coal

Directory of Open Access Journals (Sweden)

A. Ariunaa

2016-03-01

Full Text Available The technical characteristics, elemental composition of the organic and mineral matters, ash melting behaviors and carbonization and gasification reactivities of coals from Baganuur and Naryn sukhait deposits were investigated. The results of proximate and ultimate analysis confirmed that the coal from Baganuur deposit can be graded as a low rank lignite B2 mark coal and Naryn sukhait coal is a bituminous G mark one. The carbonization and gasification experiments were performed using TGA apparatus and fixed bed quartz reactor. The data obtained with two experimental reactors showed that Baganuur lignite had lower thermal stability and much higher CO2 gasification reactivity at 950°C as compared to those for Naryn sukhait bituminous coal.Mongolian Journal of Chemistry 16 (42, 2015, 22-29

Long-term behaviour of bituminized waste: modelling self-irradiation and leaching

International Nuclear Information System (INIS)

Simondi-Teisseire, B.; Vistoli, P.P.; Libert, M.; Gilardi, T.; Chaix, P.; Blanc, V.

2001-01-01

During interim storage, the main evolution factor of bituminized wastes is radiolysis, due to self-irradiation. In deep disposal conditions, after site re-saturation and corrosion of the containers, the main evolution will be due to leaching. This paper deals with two models designed to describe respectively radiolytic gas evacuation (JACOB- 2) and bituminized waste leaching (COLONBO), and some of the typical results obtained from these two models. The first model describes radiolytic gas production, diffusive transport of gas, bubble nucleation and ripening and movement under buoyancy. The second one is based on descriptions of water sorption, solubilization, and diffusion into the matrix, water uptake by the most soluble salts leading to alteration of the matrix and finally to diffusive transport of the salts outside the bitumenisate. (author)

Method for obtaining a varnish with a base of mineral oil obtained by distillation of bituminous schists

Energy Technology Data Exchange (ETDEWEB)

Marchionni, A

1945-07-24

A method for obtaining a varnish is described characterized by the fact that the following ingredients are being used; mineral oil from the distillation of bituminous schists in the proportions already cited in the description, diluted with benzene or turpentine, with admixture of coloring matter. Varnish with a base of mineral oil from the distillation of bituminous schists is obtained.

Aerobic Biofilms Grown from Athabasca Watershed Sediments Are Inhibited by Increasing Concentrations of Bituminous Compounds

Science.gov (United States)

Lawrence, John R.; Sanschagrin, Sylvie; Roy, Julie L.; Swerhone, George D. W.; Korber, Darren R.; Greer, Charles W.

2013-01-01

Sediments from the Athabasca River and its tributaries naturally contain bitumen at various concentrations, but the impacts of this variation on the ecology of the river are unknown. Here, we used controlled rotating biofilm reactors in which we recirculated diluted sediments containing various concentrations of bituminous compounds taken from the Athabasca River and three tributaries. Biofilms exposed to sediments having low and high concentrations of bituminous compounds were compared. The latter were 29% thinner, had a different extracellular polysaccharide composition, 67% less bacterial biomass per μm2, 68% less cyanobacterial biomass per μm2, 64% less algal biomass per μm2, 13% fewer protozoa per cm2, were 21% less productive, and had a 33% reduced content in chlorophyll a per mm2 and a 20% reduction in the expression of photosynthetic genes, but they had a 23% increase in the expression of aromatic hydrocarbon degradation genes. Within the Bacteria, differences in community composition were also observed, with relatively more Alphaproteobacteria and Betaproteobacteria and less Cyanobacteria, Bacteroidetes, and Firmicutes in biofilms exposed to high concentrations of bituminous compounds. Altogether, our results suggest that biofilms that develop in the presence of higher concentrations of bituminous compounds are less productive and have lower biomass, linked to a decrease in the activities and abundance of photosynthetic organisms likely due to inhibitory effects. However, within this general inhibition, some specific microbial taxa and functional genes are stimulated because they are less sensitive to the inhibitory effects of bituminous compounds or can degrade and utilize some bitumen-associated compounds. PMID:24056457

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Directory of Open Access Journals (Sweden)

Cieślik Ewelina

2018-01-01

Full Text Available One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Science.gov (United States)

Cieślik, Ewelina; Konieczny, Tomasz; Bobik, Bartłomiej

2018-01-01

One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction) were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Aqueous radioactive waste bituminization

International Nuclear Information System (INIS)

Williamson, A.S.

1980-08-01

The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

1995-12-31

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

Leaching test of bituminized waste and waste solidified by epoxy resin

International Nuclear Information System (INIS)

Yoshinaka, Kazuyuki; Sugaya, Atsushi; Onizawa, Toshikazu; Takano, Yugo; Kimura, Yukihiko

2008-10-01

About 30,000 bituminized waste drums and about 1800 drums of waste solidified by epoxy resin, generated from Tokai Reprocessing Plant, were stored in storage facilities. And study for disposal of these waste is performed. It was considered that radioactive nuclides and chemical components were released from these waste by contact of underground water, when disposed there waste. This paper is reported that result of leaching tests for these waste, done from 2003 to 2006. We've get precious knowledge and data, as follows. (1) In leaching tests for bituminized waste, it has detected iodine-129 peak, considered difficult too low energy gamma to detect. We've get data and knowledge of iodine-129 behavior first. Leached radioactivity for 50 days calculated by peak area was equal for about 40% and 100% of including radioactivity in bituminized waste sample. And we've get data of behavior of nitric acid ion and so on, important to study for disposal, in various condition of sample shape or leaching liquid temperature. (2) In leaching test for waste solidified by epoxy resin, we've get data of behavior of TBP, radionuclides and so on, important to study for disposal. Leached TBP was equal about 1% of including of sample. And we've get data of iodine-129 behavior, too. It was confirmed that leached iodine-129 was equal for about 60% and 100% of including sample, for 90 days. (author)

Wetting of bituminized ion-exchangers under simulated repository conditions

International Nuclear Information System (INIS)

Aalto, H.; Valkiainen, M.

2001-01-01

According to the present plans the spent nuclear fuel from four Finnish nuclear power units will be transferred after interim storage to the final disposal site where it will be encapsulated and disposed of in a final repository constructed into the bedrock at a depth of 500 meters. Low and medium level waste generated at nuclear power plants will be finally disposed of in caverns constructed in the bedrock at the power plant site. The safety of the final disposal is based on a multibarrier concept and the degree of safety is estimated by using predictive models. The properties of the waste form are taken into account in the design of the repository construction. Bitumen has been chosen as an immobilisation agent for the wet wastes at Olkiluoto Power Plant, where two BWR units, TVO 1 and TVO 2, have separate bituminization facilities designed by Asea-Atom. Properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied by VTT Chemical Technology since the late 70's. These studies have concentrated mainly on determining the long-term behaviour of the bituminization product under the repository conditions. Current interest lies on wetted product as a diffusion barrier. For this purpose a microscopic method for the visualisation of the structure of the wetted product has been developed. The equilibration of the samples in simulated concrete groundwater is currently going on at a temperature of 5-8 deg. C. Preliminary results are presented in this paper. Diffusion experiments have been planned for the further characterising of the wetted product as a release barrier for radionuclides including modelling. (author)

Method of distillation of sulfurous bituminous shales

Energy Technology Data Exchange (ETDEWEB)

Hallback, A J.S.; Bergh, S V

1918-04-22

A method of distillation of sulfur-containing bituminous shales is characterized by passing the hot sulfur-containing and oil-containing gases and vapors formed during the distillation through burned shale containing iron oxide, so that when these gases and vapors are thereafter cooled they will be, as far as possible, free from sulfur compounds. The patent contains six more claims.

Process of producing fuels from slates or bituminous shales. [distillation at incandescent heat

Energy Technology Data Exchange (ETDEWEB)

Huppenbauer, M

1902-07-31

A process of producing a fuel from slates or bituminous shales by saturating or impregnating them after preliminary distillation with the vapors of tars, resins, oils, etc., is given. The process is characterized by the bituminous shale being submitted in the form of fragments to distillation at incandescent heat to make the shale porous and able to absorb the vapors of the substances already mentioned.

Bituminization of radioactive wastes at the Nuclear Research Center Karlsruhe. Experience from plant operation and development work

Energy Technology Data Exchange (ETDEWEB)

Hild, W; Kluger, W; Krause, H

1976-05-01

A summary is given of the main operational experience gained at the Nuclear Research Center Karlsruhe in 4 years operation of the bituminization plant for evaporator concentrates from low- and medium level wastes. At the same time some of the essential results are compiled that have been obtained in the R + D activities on bituminization.

Comparison of the performances of several modified bituminous mix formulas

Science.gov (United States)

Saoula, Samia; Haddadi, Smail; Mokhtar, Khedidja Ait

2012-09-01

The mechanical behaviour of several formulas of bituminous concrete containing polymer (HDPE), polymer-bitumens (EVA) and waste of sole of shoes (containing copolymer butadiene-styrene-SBR noted DSBR and ethylene and vinyl acetate-EVA noted DEVA) were studied. The aim of this work is to improvement of the poor mechanicals performances of a bituminous concrete formula (0/14) which isn't conforming to the Algerian standards. Also, the mechanical tests showed that the permanent deformations and the indirect tensile strength at the temperatures of service resistances are improved. At high-temperature service, formulas of asphalt bitumen-EVA most resistant against the average temperature in service, it mixes made with waste are best resistant. All the formulas have a good behaviour with water.

Pressure analysis in ventilation ducts at bituminization facility

International Nuclear Information System (INIS)

Kikuchi, Naoki; Iimura, Masato; Takahashi, Yuki; Omori, Eiichi; Yamanouchi, Takamichi

1997-09-01

Pressure analysis in cell ventilation ducts at bituminization facility where the fire and explosion accident occured was carried out. This report also describes the results of bench mark calculations for computer code EVENT84 which was used for the accident analysis. The bench mark calculations were performed by comparing the analytical results by EVENT84 code with the experimental data of safety demonstration tests of ventilation system which were carried out by JAERI. We confirmed the applicability of EVENT84 code with the conservative results. The pressure analysis in cell ventilation ducts at bituminization facility were performed by comparing the analytical results of duct pressure by EVENT84 code with the yield stress of destroyed ducts by explosion, in order to estimate the scale of explosion. As a result, we could not explain the damage of ducts quantitatively, but we found the local pressure peaks analytically in downstream ducts where the serious damages were observed. (author)

Determination of bitumen and rubber content in bituminous mixes containing crumb tyre rubber; Determinacion del contenido de betum y de caucho en las mezclas bituminosas que incorporan plvo de caucho procedente de neumaticos fuera de uso

Energy Technology Data Exchange (ETDEWEB)

Rubio Guzamn, B.; Jimenez Saez, R.

2009-07-01

In recent years the use of crumb rubber from scrap tyres as a component of hot bituminous mixes for road construction, has been officially promoted by the Public Administration in Spain, by issuing several publications of both informative and normative nature, aimed to spread knowledge and experiences on the subject and also to specify the requirement and regulate the working applications for this material. However, it also seems necessary to develop new test methods which, allows control of the rubber content in crumb rubber-added mixes, regardless of the process (wet or dry) followed for the mix production. This article describes a procedure reliable enough to determine both the soluble bituminous binder and the rubber contents in bituminous mixes based on two combined, previously standardized test methods: binder extraction with solvent and ignition. (Author) 7 refs.

Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

Energy Technology Data Exchange (ETDEWEB)

Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

2013-07-01

The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

DEPOSITIONAL ENVIRONMENT AND ORGANIC GEOCHEMICAL CHARACTERISTICS OF LOWER EOCENE BITUMINOUS ROCKS, IN THE KÜRNÜÇ/GÖYNÜK-BOLU AREA

Directory of Open Access Journals (Sweden)

Ali SARI

2016-12-01

Full Text Available In this study, dark gray and dark brown colored, organic-carbon rich bituminous rocks (bituminous marl and bituminous shale exposing around the Kürnüç area (Göynük, Bolu are investigated by means of or- ganic geochemical characteristics. In this respect, rock lithologies, depositional environments, rock source potential, kerogen and organic maturity types and hydrocarbon generation potentials of bituminous rocks were determined. For this reason, pyrolysis (Rock Eval–VI analysis, gas chromatography (GC and gas chromatography-mass spectrometer (GC-MS analyses were carried out. In addition, spore color index (SCI was determined with organic petrographic method and stable carbon analysis (δ13C of the samples were also conducted. Lithology of the studied samples is of clastic source and the depositional environ- ment is a lagoon with a partial connection to the sea. In bituminous rocks with excellent source rock potential TOC values are in the range of 2.52-8.38 wt % (average 6.08 wt %. With the exception of two samples (Type II kerogen type of all samples is Type I. According to pyrolysis, GC and GC-MS organic maturity results, all the samples are in immature stage. Organic geochemical data indicate that bituminous rocks have an excellent oil generation potential and there is no organic contamination.

Analysis of the use of coal tar as a binder in bituminous mixtures, using Marshall and Ramcodes methodologies

International Nuclear Information System (INIS)

Ochoa-Díaz, R

2013-01-01

This paper presents an alternative use of coal tar, a by-product of the steel industry, given the problems of accumulation and negative environmental impact. Therefore, it is necessary to analyze the incorporation of coal tar as a binder in paving mixtures. First, this paper presents the origin, description of the main characteristics, and properties of tar. Then, this paper evaluates the mix of coal tar by means of the RAMCODES and Marshall methodologies to determine its resistance. The results of the tests explain the physical and mechanical properties of the mix. Taking into account the results of both methods, this paper makes a comparison to determine the suitability of the RAMCODES methodology in the mix design. Finally, it analyzes the alternatives to coal tar that can be used as binders in bituminous mixes for pavement and the advantages of their uses under some specific conditions

Synthesis document on the long time behavior of packages: operational document ''bituminous'' 2204

International Nuclear Information System (INIS)

Tiffreau, C.

2004-09-01

This document is realized in the framework of the law of 1991 on the radioactive wastes management. The 2004 synthesis document on long time behavior of bituminous sludges packages is constituted by two documents, the reference document and the operational document. This paper presents the operational model describing the water alteration of the packages and the associated radioelements release, as the gas term source and the swelling associated to the self-irradiation and the bituminous radiolysis. (A.L.B.)

Waste bituminization system in CDTN

International Nuclear Information System (INIS)

Guzella, M.F.R.; Miaw, S.T.W.

1990-01-01

Experimental works on low level waste bituminization have been developed at the Radioactive Waste Treatment Division of CDTN. A small scale bitumen extruder (1 kg/h) similar to the Angra II one is in operation. Some types of Brazilian bitumen have been selected and incorporation experiments with different types of waste were carried out; the operating conditions have been defined and the final product properties investigated. (author) [pt

Relation between particle size and properties of some bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Palmer, A.D.; Cheng, M.; Goulet, J.-C.; Furimsky, E. (CANMET, Ottawa, ON (Canada). Energy Research Laboratories)

1990-02-01

Coal fractions of different size distributions exhibited different H/C ratio, ash and sulphur contents, and surface structures. This was confirmed using two low-sulphur and two high-sulphur bituminous coals. The effect was much less pronounced for low-sulphur coals than for high-sulphur coals. A significant difference in properties was noted between the two high-sulphur coals in spite of similar basic compositional parameters. This was confirmed by the fractal dimensionality factor D of Illinois No. 6 coal, which exceeded the theoretical value. 14 refs., 9 figs., 5 tabs.

Global market trade policy analysis for petroleum oils and oils obtained from bituminous minerals, crude

Directory of Open Access Journals (Sweden)

Bagheri, F.

2012-01-01

Full Text Available This article is based on surveying the custom tariffs imposed on the world export market of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. We obtained the data according to the most updated available data provided online by UNCTAD and World Bank. The results indicate that none of the 142 countries in the world market of this product have imposed non-tariff trade barriers on the import of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. The developed countries and the countries with transition economies are the main world import partners. European Union, United States, China, Japan, South Korea, Canada, Singapore, Taiwan, Thailand, South Africa, Australia, Turkey, Brazil, Sweden and Belarus are the examples and have imposed low custom tariffs on Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude.

Low NOx firing systems for bituminous coal and lignite

International Nuclear Information System (INIS)

Knyrim, W.; Scheffknecht, G.

1997-01-01

In the case of lignite fluidized boilers the denitrification down to less than 200 mg/m 3 was possible with primary measures on the firing side only. On account of the excellent results achieved with the reconstructed plants the firing systems for the new generation of brown coal fire steam generators with a capacity of 800 MW and more is designed in a similar way. For bituminous coal fire steam generators the primary measures on the firing side are nor sufficient to keep the German NO x emission limit. Therefore these units had to be retrofitted with a SCR-DENOX plant. The experience with the new firing system made in a 110 MW steam generator in Austria with a wide range of fuels is introduced. One of the largest bituminous coal fired once-trough steam generator built by EVT is the boiler for the power station Bexbach I (750 MW). The firing system is designed as a tangential firing system with 32 jet burners. These are arranged in pairs in the corners and divided into 4 burner levels with 4 burner pairs each. One mill is allocated to each burner level. An important characteristic feature is that the four bowl mills are arranged on one side of the steam generator. The plant is constructed with upper air nozzles which are arranged above the top burner level for the reduced of nitrogen oxides. During tests at steam generator with similar design, the nO x formation could be reduced from 750 to 500 mg/m 3 s.t.p. (dry, 6% O 2 ) with an addition of upper air of 20% at 100% unit capacity and constant total flow. As a main approach for the further reduction of the primary NO x emission at bituminous coal fired steam generators with tangential firing systems, the experience gained from the firing of brown coal has also been taken into account. A fundamental aspect in this respect was the vertical air staging in the direction of the furnace height. The results of many tests in a test reactor have shown that the differences of the achievable NO x values of brown and

Unexpectedly high uptake of palladium by bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Brown, S.D.; Snape, C.E. [Univ. of Strathclyde, Dept. of Pure and Applied Chemistry, Glasgow (United Kingdom)

1997-12-31

The uptake of palladium as a conversion catalyst onto coals of different rank was investigated. Palladium fixation occurs by a different mode to that for alkaline earth and first row transition metals. Therefore, the dispersion of relatively high concentration of palladium by an ion sorption process is even possible for bituminous coals. (orig.)

Log evaluation of sub-bituminous coals in Magallanes, Chile

International Nuclear Information System (INIS)

Weltz, L.S.

1976-01-01

In coal exploration a drilling program is normally used for coal inquest through core analysis, with a high cost and operating time. However, in many cases, there is poor cores recovery due to operating procedures and/or formation conditions which leads to the determination of parameters non-representative of the coal seam. The cost and operating time can be minimized through the use of logs which also represent a continuous and in situ sampling. In the case of sub-bituminous coals, the analysis through logs is more complex due to the high content of clay, which masks the presence of water. This paper describes the analysis of sub-bituminous coals in Magallanes-Chile. The main coal seam components are: coal, clay, secondary quartz and water. An interpretation system using the density log, gamma ray, sonic and microlog, based on rho/sub B/-GR and rho/sub B/--Δ/sub T/ cross plots, permits to know the weight percentages of the following elements: total carbon, ash, moisture, which form the main local coal parameters. Empirical relationships permit us to obtain also the heating value and an estimate strength index to elastic-dynamic forces. The results obtained agree within 3 percent with the Laboratory cores analysis. The method is processed through a sequence of simple computer programs for IBM-360

Isotopic variations in the nitrogen of natural humic and bituminous organic substances

International Nuclear Information System (INIS)

Stiehl, G.; Lehmann, M.

1980-01-01

delta 15 N-values and nitrogen contents of a series of humic and bituminous organic sediments of different ranks were determined. The change of the isotopic abundance of nitrogen was investigated during heating in model experiments, using a gas flame coal. In the case of humic carbon coals the relative nitrogen contents vary from 0.8 to 1.4% and the delta 15 N-values from + 3.5 to + 6.3 parts per thousand increasing from the brown coal to anthracite ranks. During the coalification process both the delta 15 N-values and the relative nitrogen contents do not vary continuously with the rank, but pass through maxima and minima. Model experiments using a gas flame coal show the same trend. Nitrogen with delta 15 N-values of + 2.8 or -7 parts per thousand was released in pyrolysis experiments, applying a gas flame coal and a steam coal at temperatures of 650 and 1000 0 C, respectively. The investigated bituminous sediments yielded relative amounts of 0.1 to 0.8% with delta 15 N-values of + 4.2 to + 10.7 parts per thousand. The obtained results are discussed with respect to the elucidation of nitrogen genesis in natural gas deposits. (author)

Process and furnace for working bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Klotzer, M

1921-06-28

A process for working up bitumen-containing materials, such as coal, peat and shale is characterized in that the material in thin-height batches with constant shaking by means of forward and backward movement of an elongated horizontal hearth heated underneath on which the material freely lies and on which it is moved in the furnace, through a single narrow furnace space with zone-wise heating of the hearth. A drying zone, a spent-material removal zone, and a carbonization zone are provided. Under separate hoods the gases and vapors are removed from these zones.

Nigerian bituminous coal as a fuel-coal. | OGUGBUAJA | Global ...

African Journals Online (AJOL)

Nigerian bituminous coal as a fuel-coal. V O OGUGBUAJA, C L NDIOKWERE, G A DIMARI. http://dx.doi.org/10.4314/gjpas.v6i2.16113 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

Energy Technology Data Exchange (ETDEWEB)

Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

2009-03-29

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

Petrography and geochemistry of Oligocene bituminous coal from the Jiu Valley, Petrosani basin (southern Carpathian Mountains), Romania

Energy Technology Data Exchange (ETDEWEB)

Belkin, Harvey E.; Tewalt, Susan J. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Hower, James C. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); Stucker, J.D. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); University of Kentucky Department of Earth and Environmental Sciences, Lexington, KY 40506 (United States); O' Keefe, Jennifer M.K. [Morehead State University, Morehead, KY, 40351 (United States); Tatu, Calin A. [University of Medicine and Pharmacy, Department of Immunology, Clinical Laboratory No. 1, Pta. E. Murgu No. 2, RO-1900 Timisoara (Romania); Buia, Grigore [University of Petrosani, Department of Geology, University St. 20, RO-2675 Petrosani (Romania)

2010-05-01

Belt samples of Oligocene (Chattian) bituminous coal from 10 underground mines located in the Jiu Valley, Hunedoara County, Petrosani basin, Romania, have been examined and analyzed for proximate and ultimate analysis, major-, minor- and trace-element chemistry, organic petrography, and vitrinite reflectance. The mineral chemistry and mode of occurrence of trace elements also have been investigated using SEM and electron microprobe techniques. Twenty coal beds occur in the Jiu Valley and most of the samples are from bed no. 3, the most productive bed of the Dilja-Uricani Formation of Oligocene age. The Petrosani basin, oriented SW-NE, is 48-km long, 10-km wide at the eastern part and 2-km wide at the western part. The coal mines are distributed along the center of the valley generally following the Jiu de Vest River. Reflectance measurements indicate that the rank of the coals ranges from high-volatile B to high-volatile A bituminous. Overall, rank decreases from the southwest to the northeast. In bed no. 3, R{sub max} varies from 0.75% in the northeast to 0.93% in the southwest. Although, most Oligocene coals in Romania and adjacent countries are lignite in rank, the Jiu Valley bituminous coals have been affected by regional metamorphism and attending hydrothermal fluids related to the Alpine orogenic event. The coals are all dominated by vitrinite; resinite and funginite are important minor macerals in most of the coals. Pyrite and carbonate generally dominate the mineral assemblages with carbonate more abundant in the northwest. Siderite occurs as nodules and masses within the macerals (generally vitrinite). Dolomite and calcite occur as fracture fillings, plant-cell fillings, and in other authigenic forms. Late-stage fracture fillings are siderite, dolomite, calcite, and ankerite. In one instance, two populations of siderite ({proportional_to} 35 and {proportional_to} 45 wt.% FeO) plus ankerite fill a large fracture. Late-stage pyrite framboid alteration is Ni

Cause finding experiments and environmental analysis on the accident of the fire and explosion in TRP bituminization facility

International Nuclear Information System (INIS)

Fujine, Sachio; Murata, Mikio; Abe, Hitoshi

1999-09-01

This report is the summary of the cause finding experiments and environmental analysis on the accident of the fire and explosion occurred at March 11th, 1997, in TRP bituminization facility of PNC (Power Reactor and Nuclear Fuel Development Corporation). Regarding the cause finding experiments, chemical components have been analyzed for the effluent samples taken from PNC's facility, bituminized mock waste has been produced using the simulated salt effluent prepared according to the results of chemical analysis, thermal analysis and experiment of runaway exothermic reaction have been conducted using the mock waste, and the component of flammable gases emitted from the heated waste have been collected and analyzed. Regarding environmental analysis on the accident, the amount of radioactive cesium released by the accident has been calculated by the comparative analysis using the atmospheric dispersion simulation code SPEEDI with the data of environmental monitoring and the public dose has been assessed. (author)

Chemomechanics of Damage Accumulation and Damage-Recovery Healing in Bituminous Asphalt Binders

NARCIS (Netherlands)

Pauli, A.T.

2014-01-01

As a contribution to the development of mutli-scale multi-physics approaches to modelling pavement performance, the present thesis considers the topic of damage accumulation accompanied by damage recover self-healing of the bituminous asphalt phase of pavement systems. It is found insightful that by

Experimental and computational study and development of the bituminous coal entrained-flow air-blown gasifier for IGCC

International Nuclear Information System (INIS)

Abaimov, N A; Osipov, P V; Ryzhkov, A F

2016-01-01

In the paper the development of the advanced bituminous coal entrained-flow air- blown gasifier for the high power integrated gasification combined cycle is considered. The computational fluid dynamics technique is used as the basic development tool. The experiment on the pressurized entrained-flow gasifier was performed by “NPO CKTI” JSC for the thermochemical processes submodel verification. The kinetic constants for Kuznetsk bituminous coal (flame coal), obtained by thermal gravimetric analysis method, are used in the model. The calculation results obtained by the CFD model are in satisfactory agreements with experimental data. On the basis of the verified model the advanced gasifier structure was suggested which permits to increase the hydrogen content in the synthesis gas and consequently to improve the gas turbine efficiency. In order to meet the specified requirements vapor is added on the second stage of MHI type gasifier and heat necessary for air gasification is compensated by supplemental heating of the blasting air. (paper)

Relations among pH, sulfate, and metals concentrations in anthracite and bituminous coal-mine discharges, Pennsylvania

Science.gov (United States)

Cravotta, III, Charles A.

2006-01-01

Water-quality data for discharges from 140 abandoned mines in the Bituminous and Anthracite Coalfields of Pennsylvania illustrate relations among pH, sulfate, and dissolved metal concentrations. The pH for the 140 samples ranged from 2.7 to 7.3, with two modes at pH 2.5 to 4 (acidic) and 6 to 7 (near neutral). Generally, flow rates were smaller and solute concentrations were greater for low-pH samples; flow rates increased with pH. Although the pH distribution was similar for the bituminous and anthracite subsets, the bituminous discharges had smaller median flow rates, greater concentrations of sulfate, iron, and aluminum, and smaller concentrations of barium and lead than anthracite discharges with the same pH values. The observed relations between the pH and constituent concentrations can be attributed to (1) dilution of acidic water by alkaline ground water; (2) solubility control of aluminum, iron, manganese, barium, and lead by hydroxide, sulfate, and/or carbonate minerals; and (3) aqueous sulfate-complex formation. The formation of AlSO4+ and AlHSO4+2 complexes adds to the total dissolved aluminum concentration at pH of equilibrium with aluminum hydroxide or hydroxysulfate minerals and can account for 10 to 20 times greater concentrations of dissolved aluminum in bituminous discharges compared to anthracite discharges at similar pH. Sulfate complexation also can account for 10 to 30 times greater concentrations of dissolved ferric iron concentrations at equilibrium with ferrihydrite (Fe(OH)3) and/or schwertmannite (Fe8O8(OH)4.5(SO4)1.75) at pH of 3 to 5. In contrast, lower barium and lead concentrations in bituminous than anthracite discharges indicates elevated sulfate concentration could decrease mobility of these metals by the formation of insoluble minerals such as barite (BaSO4) or anglesite (PbSO4). Most samples were saturated with barite, but none were saturated with anglesite. Hence, lead concentrations could be controlled by coprecipitation with

Carbon Isotope Analyses of Individual Hydrocarbon Molecules in Bituminous Coal, Oil Shale and Murchison Meteorite

Directory of Open Access Journals (Sweden)

Kyoungsook Kim

1998-06-01

Full Text Available To study the origin of organic matter in meteorite, terrestrial rocks which contain organic compounds similar to the ones found in carbonaceous chondrites are studied and compared with Murchison meteorite. Hydrocarbon molecules were extracted by benzene and methanol from bituminous coal and oil shale and the extracts were partitioned into aliphatic, aromatic, and polar fractions by silica gel column chromatography. Carbon isotopic ratios in each fractions were analysed by GC-C-IRMS. Molecular compound identifications were carried by GC-MS Engine. Bituminous coal and oil shale show the organic compound composition similar to that of meteorite. Oil shale has a wide range of δ(13C, -20.1%_0 - -54.4%_0 compared to bituminous coal, -25.2%_0 - -34.3%_0. Delta values of several molecular compounds in two terrestrial samples are different. They show several distinct distributions in isotopic ratios compared to those of meteorite; Murchison meteorite has a range of δ(13C from -13%_0 to +30%_0. These results provide interpretation for the source and the formation condition of each rock, in particular alteration and migration processes of organic matter. Especially, they show an important clue whether some hydrocarbon molecules observed in meteorite are indigenous or not.

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

NARCIS (Netherlands)

Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

2013-01-01

The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in

Zeolite facies and regional rank of bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Kisch, H J

1966-01-01

The author has correlated diagnostic analcime-, heulandite-, and laumontite-bearing mineral assemblages from four areas in the Upper Carboniferous and the Permian of New South Wales with the rank of the associated coals, represented by the carbon content of vitrinite. The results show that lowest-grade regional metamorphism of the zeolite facies reflects at least in part the same physical conditions of metamorphism as the increase in degree of coalification (rank) in the bituminous coal range. Degree of coalification is probably independent of partial pressures of H/sub 2/O and CO/sub 2/: it is controlled mainly by maximum depth of burial, its duration, and the geothermal gradient.

Mathematical simulation of gas pressure in fibre-reinforced concrete container at radiation and biological decomposition of cellulose, bituminized and concrete radwastes

International Nuclear Information System (INIS)

Kuruc, J.; Kvito, P.

2005-01-01

Fibre-reinforced concrete container (FRCC) are used for long-time repository of radioactive wastes. Low- and middle-active radwastes from operation of the NPPs V-1, V-2 Jaslovske Bohunice, Mochovce NPP and from decommissioned NPP A-1 (Jaslovske Bohunice) are treated in the plant SE-VYZ in Jaslovske Bohunice and after immobilisation are deposited in National Radwaste Repository Mochovce (RU RAO). After filling of the RU RAO, FRCC will be stored during 300 years. During this time the integrity of the FRCC must be guaranteed. By the influence of autoradiolysis of the cellulose and bituminized radwastes as well as in cement grout the gases are formed, mainly the hydrogen, methane and carbon dioxide. In the case of presence of available water (a w ≥ 0.63) and in presence of microbes and moulds at appropriate conditions the biological decomposition of cellulose materials may proceed with formation of H 2 , CH 4 a CO 2 . With increasing of developed gases may increase pressure in FRCC, that may initiate the loss of integrity of the FRCC with following endangering of radiation safety of the RU RAO, respectively of the territory over the repository.Authors developed the new mathematical model of pressure of gases in FRCC and in deposited barrels with cellulose and bituminized radwastes. The mathematical model is based on biological decomposition of cellulose materials as well as on radiation decomposition of cellulose, bitumen and concrete. In this mathematical model the diffusion through the walls of FRCC is the main process responsible for decreasing of the pressure. This model was developed in two basic variants: (1) Mathematical model of gas pressure in FRCC as function of dose; (2) Mathematical model of gas pressure in FRCC as function of mass of cellulose

Assessing radioactive concentrates and waste vapor condensate in solidifying radioactive wastes by bituminization

International Nuclear Information System (INIS)

Tibensky, L.; Krejci, F.; Breza, M.; Timulak, J.; Hladky, E.

1986-01-01

A brief overview is presented of chemical and radiochemical methods used in the world for the analysis of the concentrate of liquid radioactive wastes from nuclear power plants destined for bituminization. Most methods are also suitable for an analysis of the condensate of waste vapors produced in bituminization. The methods of analysis of the radioactive concentrate from the V-1 nuclear power plant in Jaslovske Bohunice and of the waste vapors condensate were developed and tested in practice. Gross gamma activity was measured using a well-type Na(Tl) scintillation detector, the content of radionuclides was determined using semiconductor Ge(Li) spectrometry. The concentration of boric acid in the concentrate was determined by titration with mannite; in the condensate, using spectrophotometry with curcumine. The content of nitrates in both the concentrate and the condensate was determined spectrophotometrically using salicylic acid, the content of nitrites was determined by spectrophotometry using sulfanilic acid and α-naphthylamine. Carbonates and chlorides were determined by titration, sodium and potassium by flame photometry. The content of organic acids was measured by gravimetry of extracted methyl esters, the content of surfactants by spectrophotometry. Infrared spectrophotometry was used in determining hydrocarbons in the waste vapor condensate. The measured value range and the measurement errors are shown for each method. (A.K.)

Elemental analysis of Indonesian and Australian bituminous coal used at Kapar Power Station

International Nuclear Information System (INIS)

Muneer Saleh; Ahmad Suhaimi

2008-01-01

An instrumental neutron activation analytical (INAA) technique is used for the determination of thirty elements in five coal samples collected from Kapar power station, imported from Indonesia and Australia. Analyses of the samples are being associated with standards. All irradiation were performed in the nuclear reactor of Malaysia Nuclear Agency (MNA). samples were counted by Hyper Pure Germanium (HPGe) detector for short period irradiations at MNA, while for the long period irradiations the samples were counted at Universiti Kebangsaan Malaysia (UKM). The concentrations of thirty elements have been determined: The major components are Cl, Ca, Mg, K, Fe, Ti, and Na with the mean concentrations in the range between 70±69 ppm-6100±1639 ppm; and the trace elements are Zr, V, Mn, Sc, Cr, Co, As, Br, Rb, Sb, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, Hf, Th, U and Ta with the mean concentrations in the range between 0.1381±0.0202 - 69.0±2.8 ppm. The results have been compared to the reported data of eight coal samples from the United States and the reported data of Australian bituminous coal. (Author)

Analysis of the sensitivity of the impact resonance frequency test as a tool to determine the elastic properties of bituminous materials; Análisis de la sensibilidad del ensayo de resonancia por impacto como herramienta para determinar las propiedades elásticas de materiales bituminosos.

Energy Technology Data Exchange (ETDEWEB)

Tauste, R.; Moreno-Navarro, F.; Gallego, R.; Rubio-Gámez, M.C.

2017-07-01

The modulus value of bituminous materials is a key factor in the design of road pavements and the estimation of their life service. This parameter can be measured in laboratory but, unfortunately, this requires the deterioration of the pavement so as the consumption of time and resources. Therefore, this study analyses the feasibility of using impact resonance frequency tests as an alternative to traditional methods for determining the dynamic modulus of bituminous mixtures. The sensitivity of this technique has been studied by analyzing its repeatability and reproducibility, studying the variations in the values measured by modifying the dimensions of the specimens, test temperatures and types of mixture tested. In addition, this non-destructive technique has been compared with other traditional tests used to determine the elastic properties of bituminous materials. The results show that this test could be an interesting tool to characterize the properties and damage state of asphalt layers. [Spanish] El valor de módulo de los materiales bituminosos es un factor clave en el diseño de pavimentos y la estimación de su vida de servicio. Este parámetro puede ser medido en laboratorio pero, desafortunadamente, esto requiere deteriorar el pavimento así como el consumo de tiempo y recursos. Por ello, este estudio analiza la viabilidad de usar el ensayo de frecuencia de resonancia mediante impacto como alternativa a los métodos tradicionales para determinar el módulo dinámico de mezclas bituminosas. La sensibilidad de esta técnica se ha estudiado analizando su repetibilidad y reproducibilidad, estudiando variaciones en los valores medidos al modificar dimensiones de probetas, temperaturas y tipos de mezcla ensayados. Además, esta técnica no destructiva se ha comparado con otros ensayos tradicionales empleados para determinar propiedades elásticas de materiales bituminosos. Los resultados muestran este ensayo como una herramienta interesante para caracterizar

Noise Reduction Properties of an Experimental Bituminous Slurry with Crumb Rubber Incorporated by the Dry Process

Directory of Open Access Journals (Sweden)

Moisés Bueno

2014-08-01

Full Text Available Nowadays, cold technology for asphalt pavement in the field of road construction is considered as an alternative solution to conventional procedures from both an economic and environmental point of view. Among these techniques, bituminous slurry surfacing is obtaining an important role due to the properties of the obtained wearing course. The functional performance of this type of surfaces is directly related to its rough texture. Nevertheless, this parameter has a significant influence on the tire/road noise generation. To reduce this undesirable effect on the sound performance, new designs of elastic bituminous slurries have been developed. Within the FENIX project, this work presents the acoustical characterization of an experimental bituminous slurry with crumb rubber from wasted automobile tires incorporated by the dry process. The obtained results show that, under controlled operational parameters, the close proximity sound levels associated to the experimental slurry are considerably lower than those emitted by a conventional slurry wearing course. However, after one year of supporting traffic loads and different weather conditions, the evaluated bituminous slurry, although it conserves the original noise reduction properties in relation to the conventional one, noticeably increases the generated sound emission. Therefore, it is required to continue improving the design of experimental surfaces in order to enhance its long-term performance.

THE HISTORY OF EXPLORATION AND EXPLOITATION OF BITUMINOUS AND KEROGENOUS DEPOSITS IN CROATIA

Directory of Open Access Journals (Sweden)

Berislav Šebečić

1995-12-01

Full Text Available It is assumed thal the first known sedimens of natural bitumen or asphalt in coastal Croatia were exploited as the early moddle ages. Yet authenticated written documents about Vinišće near Trogir derive from no earlier than 1628, about Vrgorac/Paklina from only 1753. By the end of the 18th century, many deposits were discovered in Dalmatia, but it was Škrip on the Island of Brač and Suhi Dolac that were important. The earliest known deposits and occurrences of kerogenous rocks, or bituminous or oil shales, are mentioned as stone or fossil coal in Sovinjak, in the upper course of the River Mirna, and in Rebići in Istria; near Sinj, Slivno not far from the River Neretva, Mirta and near Nerežišće on the Island uf Brač. All if these were well known and described in 1804, while Sovinjak was mentioned in the 16th century. In the article, some of new information derived from mining and geological research into bituminous and kerogenous sediments and deposits are provided (the paper is published in Croatian.

Effect of bituminous coal properties on carbon dioxide and methane high pressure sorption

Czech Academy of Sciences Publication Activity Database

Weishauptová, Zuzana; Přibyl, Oldřich; Sýkorová, Ivana; Machovič, Vladimír

2015-01-01

Roč. 139, JAN 1 (2015), s. 115-124 ISSN 0016-2361 Institutional support: RVO:67985891 Keywords : bituminous coal * sorption capacity * maceral composition * Upper Silesian Coal Basin Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.611, year: 2015

Trace elemental analysis of bituminous coals using the Heidelberg proton microprobe

Energy Technology Data Exchange (ETDEWEB)

Chen, J R; Kneis, H; Martin, B; Nobiling, R; Traxel, K [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany, F.R.); Heidelberg Univ. (Germany, F.R.). Physikalisches Inst.); Chao, E C.T.; Minkin, J A [Geological Survey, Reston, VA (USA)

1981-03-01

Trace elements in coal can occur as components of either the organic constituents (macerals) or the inorganic constituents (minerals). Studies of the concentrations and distribution of the trace elements are vital to understanding the geochemical milieu in which the coal was formed and in evaluating the attempts to recover rare but technologically valuable metals. In addition, information on the trace element concentrations is important in predicting the environmental impact of burning particular coals, as many countries move toward greater utilization of coal reserves for energy production. Traditionally, the optical and the electron microscopes and more recently the electron microprobe have been used in studying the components of coal. The proton-induced X-ray emission (PIXE) microprobe offers a new complementary approach with an order of magnitude or more better minimum detection limit. We present the first measurements with a PIXE microprobe of the trace element concentrations of bituminous coal samples. Elemental analyses of the coal macerals-vitrinite, exinite, and inertinite - are discussed for three coal samples from the Eastern U.S.A., three samples from the Western U.S.A., and one sample from the Peoples Republic of China.

Stimuli-Adaptable Materials

DEFF Research Database (Denmark)

Frankær, Sarah Maria Grundahl

The work presented in this Thesis deals with the development of a stimuli-adaptable polymer material based on the UV-induced dimerisation of cinnamic acid and its derivatives. It is in the nature of an adhesive to adhere very well to its substrate and therefore problems can arise upon removal...

Use of additives to improve the capacity of bituminous mixtures to be heated by means of microwaves; Uso de un material volcánico como filler en la producción de hormigones autocompactantes de baja resistencia.

Energy Technology Data Exchange (ETDEWEB)

Gallego, J.; Val, M.A. del; Contreras, V.; Páez, A.

2017-07-01

This study examines the potential of adding electric arc furnace slag to bituminous mixtures to be heated by microwaves. The susceptibility of bituminous mixtures to microwave energy is limited and so, in order to improve the energy performance of the heating process, it is necessary to incorporate additives or components to the mixture so as to improve the capacity for microwave heating. The article presents the results of adding various components, (steel wool, scrap tire wire, silicon carbide, iron filings) and an alternative aggregate: electric arc furnace slag. According to the results obtained in the laboratory, slag addition of at least 5% by weight of the bituminous mixture represents the best option for both technical and economic reasons. The results may promote the valorization of this steel industry residue in bituminous mixtures by improving microwave heating response. [Spanish] El presente trabajo examina el potencial de añadir escorias siderúrgicas de horno de arco eléctrico en mezclas bituminosas cuando se calientan con energía de microondas. La susceptibilidad de las mezclas bituminosas a las microondas es limitada y con el objetivo de incrementarla es necesario incorporar aditivos o componentes que sí son susceptibles. El artículo presenta los resultados obtenidos con varios aditivos (lana de acero, alambre metálico reciclado de neumáticos fuera de uso, carburo de silíceo y limaduras de hierro) y un árido alternativo: escorias de horno de arco eléctrico. De acuerdo con los resultados obtenidos en el estudio, la incorporación de escorias en al menos un 5% en masa de la mezcla bituminosa representa la mejor opción por motivos técnicos y económicos. Este resultado puede potenciar la valorización de este residuo de la industria del acero en mezclas bituminosas para mejorar su respuesta al calentamiento con energía microondas.

Report on the bituminous coal liquefaction sub-committee in fiscal 1993; 1993 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in fiscal 1993. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant, launched in fiscal 1991, will be performed under the operation research plan for efficient operation, based on the result of discussing the total project cost in fiscal 1992. The status of constructing the 150-t/d pilot plant in fiscal 1993 is in the phase of making the foundations subsequently from fiscal 1992, procurement of devices and construction materials, constructions of iron structures, installation, heat insulation, and painting, and building the central control building and piping facilities outside the battery limit. The paper also reports the tests and investigations on improving performance of natural pylite catalyst, the tests and investigations on improving performance of circulating solvent, and the technological investigations on structuring a liquefying reaction data analyzing system. For the supportive researches on the pilot plant, the paper describes studies by using a 1-t/d PSU, studies on coal liquefaction conditions, studies on synthesized iron sulfide catalysts, and studies on solvent hydrogenating catalysts. A comprehensive discussion was also given. (NEDO)

Towards an Accurate Stress Dependant Time & Frequency Domain VE Response Model for Bituminous Binders

NARCIS (Netherlands)

Woldekidan, M.F.; Huurman, M.; Pronk, A.C.

2010-01-01

Linear viscoelastic properties of bituminous binders for short loading times are analyzed using dynamic mechanical analysis methods. Dynamic Shear Rheometer (DSR) test with parallel plate (PP) configuration is widely used for this purpose. Due to the complex stress distribution over the

Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

Science.gov (United States)

Zhang, Lihui; Duan, Feng; Huang, Yaji

2015-04-01

Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Developing an Instructional Material Using a Concept Cartoon Adapted to the 5E Model: A Sample of Teaching Erosion

Science.gov (United States)

Birisci, Salih; Metin, Mustafa

2010-01-01

Using different instructional materials adapted within the constructivist learning theory will enhance students' conceptual understanding. From this point of view, an instructional instrument using a concept cartoon adapted with 5E model has developed and introduced in this study. The study has some deficiencies in investigating students'…

Investigation of activity release from bituminized intermediate-level waste forms under thermal stresses

International Nuclear Information System (INIS)

Kluger, W.; Vejmelka, P.; Koester, R.

1983-01-01

To determine the consequences of a fire during fabrication, intermediate storage and transport of bituminized NaNO 3 waste forms, the fractions of plutonium released from the waste forms were assessed. For this purpose, laboratory tests were made with PuO 2 -containing specimens as well as a field test with specimens containing Eu 2 O 3 . By the evaluation of plutonium release in the laboratory and by the determination of the total sodium release and the relative Eu/Na release in the field tests the plutonium release can be deduced from full-scale specimens. The results show that for bituminized waste forms with high NaNO 3 contents (approx. 36 wt%) the average plutonium release obtained in laboratory testing is 15%. In the field tests (IAEA fire test conditions) an average Eu release of 8% was found. These results justify the statement that also for waste forms in open 175 L drum inserts a maximum plutonium release of about 15% can be expected. From the time-dependence of Eu/Na release in the field tests an induction period of 15-20 minutes between the start of testing and the first Na/Eu release can be derived. The maximum differential Na/Eu release occurs after a test period of 45 to 60 minutes duration and after 90 to 105 minutes (tests K2 and K4, respectively); after that time also the highest temperatures in the products are measured. The release values were determined for products in open 175 L drum inserts which in this form are not eligible for intermediate and ultimate storage. For bituminized waste forms in concrete packages (lost concrete shieldings) a delayed increase in temperature to only 70-80 deg. C takes place (4-5 hours after extinction of the fire) if the fire lasts 45 minutes. The concrete package remains intact under test conditions. This means that activity release from bituminized waste forms packaged in this way can be ruled out in the case under consideration. (author)

Enhancing the Ductility of Laser-Welded Copper-Aluminum Connections by using Adapted Filler Materials

Science.gov (United States)

Weigl, M.; Albert, F.; Schmidt, M.

Laser micro welding of direct copper-aluminum connections typically leads to the formation of intermetallic phases and an embrittlement of the metal joints. By means of adapted filler materials it is possible to reduce the brittle phases and thereby enhance the ductility of these dissimilar connections. As the element silicon features quite a well compatibility with copper and aluminum, filler materials based on Al-Si and Cu-Si alloys are used in the current research studies. In contrast to direct Cu-Al welds, the aluminum filler alloy AlSi12 effectuates a more uniform element mixture and a significantly enhanced ductility.

Characterization of uranium in bituminized radioactive waste drums by self-induced X-ray fluorescence

International Nuclear Information System (INIS)

Pin, Patrick; Perot, Bertrand

2013-06-01

This paper reports the experimental qualification of an original uranium characterization method based on fluorescence X rays induced by the spontaneous gamma emission of bituminized radioactive waste drums. The main 661.7 keV gamma ray following the 137 Cs decay produces by Compton scattering in the bituminized matrix an intense photon continuum around 100 keV, i.e. in the uranium X-ray fluorescence region. 'Self-induced' X-rays produced without using an external source allow a quantitative assessment of uranium as 137 Cs and uranium are homogeneously mixed and distributed in the bituminized matrix. The paper presents the experimental qualification of the method with real waste drums, showing a detection limit well below 1 kg of uranium in 20 min acquisitions while the usual gamma rays of 235 U (185 keV) or 238 U (1001 keV of 234m Pa in the radioactive decay chain) are not detected. The relative uncertainty on the uranium mass assessed by self-induced X-ray fluorescence (SXRF) is about 50%, with a 95% confidence level, taking into account the correction of photon attenuation in the waste matrix. This last indeed contains high atomic numbers elements like uranium, but also barium, in quantities which are not known for each drum. Attenuation is estimated thanks to the peak-to-Compton ratio to limit the corresponding uncertainty. The SXRF uranium masses measured in the real drums are in good agreement with long gamma-ray spectroscopy measurements (1001 keV peak) or with radiochemical analyses. (authors)

Multistability in Bistable Ferroelectric Materials toward Adaptive Applications

NARCIS (Netherlands)

Ghosh, Anirban; Koster, Gertjan; Rijnders, Augustinus J.H.M.

2016-01-01

Traditionally thermodynamically bistable ferroic materials are used for nonvolatile operations based on logic gates (e.g., in the form of field effect transistors). But, this inherent bistability in these class of materials limits their applicability for adaptive operations. Emulating biological

Low-temperature carbonization of bituminous coal for the production of solid, liquid, and gaseous fuels

Energy Technology Data Exchange (ETDEWEB)

1942-01-01

Properties and uses of low-temperature coke for producing ferrosilicon, CaC/sub 2/ generator gas and water gas, as a fuel for boilers and household use and as a diluent for coking coal, and the properties and uses of low-temperature tar, gasoline, gas, and liquefied gas are described. By using a circulating gas, it is possible to obtain in low-temperature carbonization of bituminous coal a fuel oil for the navy. Aging-test data of such an oil are given. Several plants in Upper Silesia, using the Lurgi circulation process are producing a fuel oil that meets specification.

Marginal adaptation and CAD-CAM technology: A systematic review of restorative material and fabrication techniques.

Science.gov (United States)

Papadiochou, Sofia; Pissiotis, Argirios L

2018-04-01

The comparative assessment of computer-aided design and computer-aided manufacturing (CAD-CAM) technology and other fabrication techniques pertaining to marginal adaptation should be documented. Limited evidence exists on the effect of restorative material on the performance of a CAD-CAM system relative to marginal adaptation. The purpose of this systematic review was to investigate whether the marginal adaptation of CAD-CAM single crowns, fixed dental prostheses, and implant-retained fixed dental prostheses or their infrastructures differs from that obtained by other fabrication techniques using a similar restorative material and whether it depends on the type of restorative material. An electronic search of English-language literature published between January 1, 2000, and June 30, 2016, was conducted of the Medline/PubMed database. Of the 55 included comparative studies, 28 compared CAD-CAM technology with conventional fabrication techniques, 12 contrasted CAD-CAM technology and copy milling, 4 compared CAD-CAM milling with direct metal laser sintering (DMLS), and 22 investigated the performance of a CAD-CAM system regarding marginal adaptation in restorations/infrastructures produced with different restorative materials. Most of the CAD-CAM restorations/infrastructures were within the clinically acceptable marginal discrepancy (MD) range. The performance of a CAD-CAM system relative to marginal adaptation is influenced by the restorative material. Compared with CAD-CAM, most of the heat-pressed lithium disilicate crowns displayed equal or smaller MD values. Slip-casting crowns exhibited similar or better marginal accuracy than those fabricated with CAD-CAM. Cobalt-chromium and titanium implant infrastructures produced using a CAD-CAM system elicited smaller MD values than zirconia. The majority of cobalt-chromium restorations/infrastructures produced by DMLS displayed better marginal accuracy than those fabricated with the casting technique. Compared with copy

Overview of BELGATOM's industrial experience in the field of radwaste bituminization, cementation and radwaste package storage

International Nuclear Information System (INIS)

Glibert, R.; Debieve, P.; Averbeke, J. van; Centner, B.

1993-01-01

Radioactive waste processing experience in Belgium is introduced. BELGATOM partners in Belgium have accumulated experience for over 25 years in the field of rad waste treatment and conditioning by bituminization and cementation and in the storage of the resulting rad waste packages

Topology optimization of compliant adaptive wing leading edge with composite materials

Directory of Open Access Journals (Sweden)

Tong Xinxing

2014-12-01

Full Text Available An approach for designing the compliant adaptive wing leading edge with composite material is proposed based on the topology optimization. Firstly, an equivalent constitutive relationship of laminated glass fiber reinforced epoxy composite plates has been built based on the symmetric laminated plate theory. Then, an optimization objective function of compliant adaptive wing leading edge was used to minimize the least square error (LSE between deformed curve and desired aerodynamics shape. After that, the topology structures of wing leading edge of different glass fiber ply-orientations were obtained by using the solid isotropic material with penalization (SIMP model and sensitivity filtering technique. The desired aerodynamics shape of compliant adaptive wing leading edge was obtained based on the proposed approach. The topology structures of wing leading edge depend on the glass fiber ply-orientation. Finally, the corresponding morphing experiment of compliant wing leading edge with composite materials was implemented, which verified the morphing capability of topology structure and illustrated the feasibility for designing compliant wing leading edge. The present paper lays the basis of ply-orientation optimization for compliant adaptive wing leading edge in unmanned aerial vehicle (UAV field.

Geochemistry of radioactive elements in bituminous sands and sandstones of Permian bitumen deposits of Tatarstan (east of the Russian plate)

Science.gov (United States)

Mullakaev, A. I.; Khasanov, R. R.; Badrutdinov, O. R.; Kamaletdinov, I. R.

2018-05-01

The article investigates geochemical features of Permian (Cisuralian, Ufimian Stage and Biarmian, Kazanian Stage of the General Stratigraphic Scale of Russia) bituminous sands and sandstones located on the territory of the Volga-Ural oil and gas province (Republic of Tatarstan). Natural bitumens are extracted using thermal methods as deposits of high-viscosity oils. In the samples studied, the specific activity of natural radionuclides from the 238U (226Ra), 232Th, and 40K series was measured using gamma spectrometry. As a result of the precipitation of uranium and thorium and their subsequent decay, the accumulation of radium (226Ra and 228Ra) has been shown to occur in the bituminous substance. In the process of exploitation of bitumen-bearing rock deposits (as an oil fields) radium in the composition of a water-oil mixture can be extracted to the surface or deposited on sulfate barriers, while being concentrated on the walls of pipes and other equipment. This process requires increased attention to monitoring and inspection the environmental safety of the exploitation procedure.

Continuous distillation of bituminous shale. [hot gas in chamber and chamber heated externally

Energy Technology Data Exchange (ETDEWEB)

1921-04-27

A process of continuous distillation of bituminous shale is given in which the heat necessary is produced not only on the exterior but also in the interior of the distillation apparatus in the form of hot gas directly bathing the shale. The residual carbon in the shale after distillation, or maybe with other fuel added to it, can be utilized; the fuel may be utilized not only for the heat it furnishes but also for the gas it gives and which adds itself to the incondensable gas from the distillation. The temperature of the zone of distillation of the shale is regulated by the quantity of gas, the temperature of this gas (which can be lowered voluntarily by injecting into the air a certain quantity of water vapor), the length of the zone comprised between the zone of gasification and distillation; the injection of water vapor permits the recovery of part of the nitrogen of the shale in the form of ammonia; the materials are withdrawn continuously in a mechanical way.

Using proximate analysis to characterize airborne dust generation from bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Page, S.J.; Organiscak, J.A.

2005-11-01

Prolonged exposure to airborne respirable coal dust is responsible for coal workers pneumoconiosis (CWP), commonly called black lung. Health research studies have identified that the prevalence and severity of CWP are directly related to both the amount of dust exposure and the coal rank. The amount of airborne respirable dust (ARD) smaller than 10 micrometers generated from breakage of different coals varies widely. To investigate the cause, researchers for the National Institute for Occupational Safety and Health (NIOSH) have conducted experiments to identify the causes of airborne respirable dust liberation. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals from eight mines. The results indicate that the proximate analysis of a coal sample can provide a very good indicator of the potential for a dust problem. For application to the coal mining, processing, and utilization industries, data from 977 US coal seams compiled by the Department of Energy (DoE) has been used to calculate this dust generation potential from an equation based on the NIOSH measured data. A simple procedure for this calculation is provided. 1 fig.

Development of a methodology to determine the radionuclide inventory of bituminized waste packages; Entwicklung eines Verfahrens zur Bestimmung des Nuklid-Inventars in bituminierten Abfallgebinden

Energy Technology Data Exchange (ETDEWEB)

Mesalic, E.; Kortmann, F.; Lierse von Gostomski, C.

2016-02-22

For the declaration of the nuclide-inventory of bituminous waste there are currently no standardized sampling-, dissolving- and analysis methods such as for cemented waste, resins and sludge is the case. The aim of this project was to develop a method for the destructive sampling and subsequent radionuclide separation and declaration for the characterization of bituminized waste. The qualitative and quantitative results of non-destructive measurement methods (segmented gamma scanning in combination with digital radiography and gamma transmission computed tomography) are compared with results from destructive analysis. The project involves: - the development of a routine method for sampling bituminized 200-L-waste containers, exemplarily applied to real drums with bituminized waste. - the development of destructive treatment and preparation methods for the obtained bitumen samples with subsequent analysis for: - Alpha emitters, e.g. Pu-, Am- and Cm-isotopes, - Beta/Gamma emitters, e.g. Co-60, Cs-137, - pure Beta emitters, e.g. Sr-90. - Comparison of the results from destructive and non-destructive methods.

Effect of mix parameters on longevity of bituminous mixtures

Science.gov (United States)

Reichle, Clayton Matthew

This study was performed to evaluate the effects of varying aggregate sources, aggregate gradations on the stripping and rutting potential of bituminous based plant mixes specified by the Missouri Department of Transportation. The different aggregate combinations included two different aggregate sources (Potosi Dolomite and Jefferson City Dolomite) including two variations for the Jefferson City Dolomite mix to simulate a marginally in-specification mix and an out-of-specification but in-field tolerance mix. The "field" mix simulated the marginal mix where field tolerance of high dust and low binder content were maximized. All three mixes were evaluated for stripping susceptibility using the Tensile Strength Ratio (TSR) test and the Hamburg Wheel Tracking Device (HWTD). The mix characteristics (unit weight, effective binder content, and air voids) were used for a Level 3 analysis in the Mechanistic-Empirical Pavement Design Guide (MEPDG) to determine long term pavement distress conditions such as fatigue cracking, rutting, and IRI (smoothness). The Potosi mix exhibited the best resistance to rutting and stripping during both the TSR testing as well as the Hamburg testing. The Jefferson City In-Spec and Out-of-Spec mixes showed less resistance to rutting and stripping in order, respectively. This was expected for the Jefferson City mixes where the aggregate was of lower quality (higher Los Angeles Abrasion, Micro Deval loss, absorption, and deleterious materials). Also, in the case of the Jefferson City Out-of-Spec mix, the binder content was lower. Upon evaluating the mixes using the MEPDG software, it was shown that mix characteristics such as air voids, VMA, and VFA influenced the fatigue cracking, rutting, and IRI predictions to a minor degree.

A new radiometric instrument designed to measure the parameters of bituminous coal on transport belts

International Nuclear Information System (INIS)

Kubicek, P.

1993-01-01

A new radiometric instrument developed in Czechoslovakia, for the measurement of ash content of bituminous coal, and for the determination of approximate values of moisture and weight is described. (Author)

Oil production from bituminous materials

Energy Technology Data Exchange (ETDEWEB)

Gotting, H E.B.; Gotting, L K

1940-07-30

The material such as shale, coal, lignite and the like, is heated in an externally heated retort and the generated gas is passed to a series of cells comprising a bubble tower, the cells of which are separated by plates, through which pipes, with perforated caps pass, also overflow pipes. The gas passing through the cell produces further oil vapour, and is decomposed by heated oil into lighter fractions, till it passes out of the tower through a pipe and through condensing coil to receiving vessels for the oil. Fixed gas passes to cylindrical wash vessels, the back pressure inducing the required pressure in the retort.

Chemical activation of bituminous coal for hampering oligomerization of organic contaminants.

Science.gov (United States)

Yan, Liang; Sorial, George A

2011-12-15

Activated carbons prepared by KOH activation of bituminous coal were studied for hampering oligomerization of phenolic compounds on its surface. A total of 24 activated carbons with different microporosity and BET surface area were created. The effect of the different variables of the activation process (KOH/bituminous coal ratio, heating temperature, activation time, and flow rate of nitrogen gas) on critical carbon parameters was analyzed. The impact of activated carbon on oligomerization was examined by conducting isotherm experiments at a neutral pH on Carbon(exp) produced with optimal characteristics and granular activated carbon (GAC) F400 for phenol, 2-methylphenol and 2-ethylphenol. These isotherms were collected under anoxic (absence of molecular oxygen) and oxic (presence of molecular oxygen) conditions. The single solute adsorption of phenol, 2-methylphenol and 2-ethylphenol on Carbon(exp) showed no obvious differences between oxic and anoxic environment, which indicated that the Carbon(exp) sample is very effective in hampering the oligomerization of phenolic compounds under oxic conditions. On the other hand, F400, which have lower micropore percentage and BET surface area, significant increases in the adsorptive capacity had been observed when molecular oxygen was present. Copyright © 2011 Elsevier B.V. All rights reserved.

Natural radioactivity associated with bituminous coal mining in Nigeria

International Nuclear Information System (INIS)

Balogun, F.A.; Mokobia, C.E.; Fasasi, M.K.; Ogundare, F.O.

2003-01-01

Gamma spectroscopic method was used to determine the natural radioactivity associated with the mining of Nigerian bituminous coal for the purpose of determining the radiological implications of coal mining in the country. The activity concentrations of the radionuclides detected range from 0.20±0.002 to 48.42±5.32 Bq kg -1 . The overall natural radionuclide contribution to the radioactivity of the environment was found to be 404.16±23.44 Bq kg -1 . Of this, coal waste (tailing) alone contributed 49.5% representing the largest contribution. Coal contributed just 5.5%. A comparison of the concentrations obtained in this work for coal with those from other parts of the world indicates that the radioactivity content of the Nigerian bituminous coal is not significantly different. The outdoor and indoor exposure rates in air 1 m above the ground are estimated to be (6.31±1.20)x10 -8 and (7.57±1.20) x10 -8 Gy h -1 , respectively, for the mining environment. These values compare very well with the global values reported by UNSCEAR: 5x10 -8 and 6x10 -8 Gy h -1 , respectively. The resulting annual effective dose equivalent estimated is (4.49±0.74)x10 -4 Sv yr -1 . This also compares favourably with the global value -4x10 -4 Sv yr -1 , reported by UNSCEAR

The UP/SP merger could derail Western bituminous

International Nuclear Information System (INIS)

Vaninetti, J.; Leshock, J.C.

1995-01-01

The 3 billion dollars per year US Western bituminous coal industry annually produces more than 100 million tons of compliance coal to utility, industrial and export markets. About half of production is consumed locally, this sector has grown most in recent years. New markets are utilities in the Mid-west. The UP and SP railroads have profited accordingly. The merger may cause a change in the pricing strategies for the new company, leading to increased freight and coal prices. 1 fig., 1 tab

ICAN Computer Code Adapted for Building Materials

Science.gov (United States)

Murthy, Pappu L. N.

1997-01-01

The NASA Lewis Research Center has been involved in developing composite micromechanics and macromechanics theories over the last three decades. These activities have resulted in several composite mechanics theories and structural analysis codes whose applications range from material behavior design and analysis to structural component response. One of these computer codes, the Integrated Composite Analyzer (ICAN), is designed primarily to address issues related to designing polymer matrix composites and predicting their properties - including hygral, thermal, and mechanical load effects. Recently, under a cost-sharing cooperative agreement with a Fortune 500 corporation, Master Builders Inc., ICAN was adapted to analyze building materials. The high costs and technical difficulties involved with the fabrication of continuous-fiber-reinforced composites sometimes limit their use. Particulate-reinforced composites can be thought of as a viable alternative. They are as easily processed to near-net shape as monolithic materials, yet have the improved stiffness, strength, and fracture toughness that is characteristic of continuous-fiber-reinforced composites. For example, particlereinforced metal-matrix composites show great potential for a variety of automotive applications, such as disk brake rotors, connecting rods, cylinder liners, and other hightemperature applications. Building materials, such as concrete, can be thought of as one of the oldest materials in this category of multiphase, particle-reinforced materials. The adaptation of ICAN to analyze particle-reinforced composite materials involved the development of new micromechanics-based theories. A derivative of the ICAN code, ICAN/PART, was developed and delivered to Master Builders Inc. as a part of the cooperative activity.

Process of extraction in liquid way, of the bitumen from asphaltic and bituminous rocks, shale, etc

Energy Technology Data Exchange (ETDEWEB)

Freda, L

1936-06-04

A process is described for liquid extraction of the bitumen in asphaltic and bituminous rocks, shales, and the like. The substances impregnated with bitumen are suitably treated for the extraction of pitch with any given solvent derived from ethylene, in a series of apparatuses fixed and rotary at atmospheric pressure or in vacuum with vapor and hot air.

The hydrogasification of lignite and sub-bituminous coals

Science.gov (United States)

Bhatt, B.; Fallon, P. T.; Steinberg, M.

1981-02-01

A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

Gamma radiation hazard to miners in bituminous coal mines

International Nuclear Information System (INIS)

Skubacz, K.

1986-01-01

Radiation hazard to miners working in 16 bituminous coal mines was determined by a thermoluminescence method. While the miners exposure to gamma radiation is higher than that of the general population, the yearly dose was never found to exceed 5 mSv in any investigated person. Factors contributing to the estimate of the exposure hazard and the need for individual dose monitoring in mines are discussed in more detail. 3 refs., 4 figs. (author)

Materials for making coke

Energy Technology Data Exchange (ETDEWEB)

Kern, L

1936-08-19

In the preparation of carbonized fuel briquettes, material such as bituminous, lignitic, or anthracitic coal, slack, waste or shale is treated with an electropositive solution such as hydrochloric acid or an acidic chloride to bring ash-forming constituents into colloidal form. The mixture is pressed with a colloid precipitating electro-negative solution such as sodium hydroxide, and moulded, the product being heated in the absence of air and coked. In an example bituminous coal is ground and then masticated with dilute hydrochloric acid. Some dilute manganese chloride is added followed by a solution of sodium hydroxide which precipitates the metals and silica as colloidal gels while the mixture is thoroughly agitated. The plastic mass is briquetted and dried at about 125/sup 0/C and then coked in vertical ovens at 700/sup 0/C. Chlorides recovered with the distillate gases may be utilized as solvent instead of hydrochloric acid. If the coal contains a large amount of sulfur acidified manganese chloride including a large proportion of iron is used as colloid forming material, the oxides of manganese and iron subsequently precipitated forming stable compounds with the non-volatile sulfur on coking or combustion.

Organic petrology and geochemistry of Eocene Suzak bituminous marl, north-central Afghanistan: Depositional environment and source rock potential

Science.gov (United States)

Hackley, Paul C.; Sanfilipo, John

2016-01-01

Organic geochemistry and petrology of Eocene Suzak bituminous marl outcrop samples from Madr village in north-central Afghanistan were characterized via an integrated analytical approach to evaluate depositional environment and source rock potential. Multiple proxies suggest the organic-rich (TOC ∼6 wt.%) bituminous marls are ‘immature’ for oil generation (e.g., vitrinite Ro  1) indicating organic input from marine algae and/or bacterial biomass, and sterane/hopane ratios are low (0.12–0.14). Monoaromatic steroids are dominated by C28clearly indicating a marine setting. High gammacerane index values (∼0.9) are consistent with anoxia stratification and may indicate intermittent saline-hypersaline conditions. Stable C isotope ratios also suggest a marine depositional scenario for the Suzak samples, consistent with the presence of marine foraminifera including abundant planktic globigerinida(?) and rare benthic discocyclina(?) and nummulites(?). Biomarker 2α-methylhopane for photosynthetic cyanobacteria implies shallow photic zone deposition of Madr marls and 3β-methylhopane indicates presence of methanotrophic archaea in the microbial consortium. The data presented herein are consistent with deposition of Suzak bituminous marls in shallow stratified waters of a restricted marine basin associated with the southeastern incipient or proto-Paratethys. Geochemical proxies from Suzak rock extracts (S content, high polar content, C isotopes, normal (αααR) C27–29 steranes, and C29/C30 and C26/C25 hopane ratios) are similar to extant data from Paleogene oils produced to the north in the Afghan-Tajik Basin. This observation may indicate laterally equivalent strata are effective source rocks as suggested by previous workers; however, further work is needed to strengthen oil-source correlations.

Effect of transesterification degree and post-treatment on the in-service performance of NCO-functionalized vegetable oil bituminous products

OpenAIRE

Cuadri Vega, Antonio Abad; García Morales, Moisés; Navarro Domínguez, Francisco Javier; Partal López, Pedro

2014-01-01

The bitumen modification through polyurethane prepolymers presents significant benefits for the manufacture of bituminous products for the paving industry. In this sense, this work explores the use, as bitumen modifier, of a novel reactive prepolymer synthesized by reaction of 4,4´,diphenylmethane diisocyanate (MDI) and a vegetable oil-based polyol, castor oil (CO), previously transesterified with pentaerythritol. On the one hand, thermal analysis on transesterified CO revealed a highly stabl...

Process to dry and preheat fine-grained bituminous coal using non- or weakly baking coal and/or carbon materials. Verfahren zur Trocknung und Vorerhitzung von feinkoerniger Steinkohle unter Verwendung nicht oder nur schwach backender Kohle und/oder Kohlenstofftraegern

Energy Technology Data Exchange (ETDEWEB)

Echterhoff, J.; Frick, H.; Schaper, A.; Mohmeyer, H.

1982-11-04

Fine-grained bituminous coal is dried and preheated in an inert gas to prevent its oxidation. The inert gas consists essentially of steam which originates from the coal to be dried. The coal is heated besides by using steam intensively but gently. The drying is carried out in a drying drum in co-current flow. The coal is mixed with a binding agent in the presence of steam. The dried and preheated coal is taken out and, after being covered with a binding agent, transported without further safety measures to the atmosphere, stored and further processed. (KHH).

The bituminization of intermediate level liquid radioactive wastes at Eurochemic. Part 3

International Nuclear Information System (INIS)

Demonie, M.; Hild, W.; Kokkelenberg, F.; Kretschmer, H.

1980-10-01

After 5.050 hours of operation, the screw elements of the extruder evaporator in the bituminization plant have been exchanged for elements with a higher abrasion resistance. The report describes the various working phases that have led, within ten weeks, to a successful accomplishment, and gives details on the required manpower, the total dose commitment, the wastes produced, and the wear of the extruder screw elements. (author)

Swelling behavior of several bituminous coals and their thermally treated coals

Energy Technology Data Exchange (ETDEWEB)

Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

2007-07-01

The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

Chemical composition of spoil from bituminous coal and anthracite in Spain. Composicion quimica de los esteriles de hulla y antracita de Espana

Energy Technology Data Exchange (ETDEWEB)

Gonzalez Canibano, J; Fernandez Valcarce, A

1991-05-01

The article describes the chemical composition of spoil from bituminous coal and anthracite in Spain. Chemical composition, mineralogical properties and physical and mechanical characteristics are used to determine the most suitable application for the spoil in order to solve the problem of disposal. 20 refs., 5 figs., 4 tabs.

Thermotropic and Thermochromic Polymer Based Materials for Adaptive Solar Control

Directory of Open Access Journals (Sweden)

Olaf Mühling

2010-12-01

Full Text Available The aim of this review is to present the actual status of development in adaptive solar control by use of thermotropic and organic thermochromic materials. Such materials are suitable for application in smart windows. In detail polymer blends, hydrogels, resins, and thermoplastic films with a reversible temperature-dependent switching behavior are described. A comparative evaluation of the concepts for these energy efficient materials is given as well. Furthermore, the change of strategy from ordinary shadow systems to intrinsic solar energy reflection materials based on phase transition components and a first remark about their realization is reported. Own current results concerning extruded films and high thermally stable casting resins with thermotropic properties make a significant contribution to this field.

Method of simultaneous recovery of oil and sulfur from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

1919-02-25

The method consists of means for dry distillation of bituminous shales in furnaces heated from inside to recover simultaneously oil and sulfur, and is characterized by obtaining the sulfur partly in the form of sulfuretted hydrogen as a direct distillation product produced in the upper part of the furnace and partly in the form of free sulfur formed in the reduction zone of the furnace by the reduction of the sulfur dioxide formed in the burning zone. It is also characterized by the recovery of sulfur--in so far as the reduction and formation of sulfur dioxide are concerned--being regulated by means of the corresponding regulation of the proportion of the speed of discharging to the amount of air introduced into the process.

Optimization of the encapsulation process of bituminized radioactive wastes

International Nuclear Information System (INIS)

Silva, Jarine E.C.; Tello, Clédola C.O.

2017-01-01

The objective of this paper is to propose alternatives for the deposition of bituminized waste in metallic packages coated with a cementitious matrix for surface repository, aiming to meet the standards criteria and increasing the integrity of the metallic packaging during the planned storage time, transportation and disposal. For this purpose, tests will be carried out to evaluate cement pastes and mortar with cementitious additives, aiming at the durability and reduction of pores. Leaching tests with different thicknesses will also be carried out, where optimization of the encapsulation can meet safety, durability and economy standards for the repository, as well as practices that contribute to reduce environmental impacts and the economic burden imposed on future generations

Reducing the emissions of nitrogen oxides when burning Kuznetsk bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Kotler, V.R.

1983-02-01

Bituminous coals from the Kuzbass have a high nitrogen content. As a result, emissions of NO/SUB/x from power stations burning these coals frequently exceed the existing Standard. In order to reduce NO/SUB/x emissions tests were carried out using stage-wise combustion, supplying to the burners only part of the air required for complete combustion. The remaining air is supplied via tertiary nozzles situated about 14 m above the burners. As a result of the tests, this method of combustion is recommended for low-sulphur Kuznetsk coals for all sub-critical boilers having dry-bottom furnaces. Extension to boilers with wet-bottom furnaces and to supercritical boilers requires further investigation.

Sustainable use of oil sands for geotechnical construction and road building

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2012-02-01

Full Text Available Oil sands are natural deposits of bituminous sand materials that are mined and processed for crude oil. They are routinely used in oil sand fields for building temporary and sometimes permanent roads serving mining and hauling activities. Although...

Effectiveness of ProTaper Universal retreatment instruments used with rotary or reciprocating adaptive motion in the removal of root canal filling material.

Science.gov (United States)

Capar, I D; Arslan, H; Ertas, H; Gök, T; Saygılı, G

2015-01-01

To compare the effectiveness of ProTaper Universal retreatment instruments with continuous rotation and adaptive motion (AM; a modified reciprocating motion that combines rotational and reciprocating motion) in the removal of filling material. Mesiobuccal root canals in 36 mandibular first molars were instrumented up to size F2 with the ProTaper Universal instrument (Dentsply Maillefer, Ballaigues, Switzerland) and filled using sealer and ProTaper Universal F2 gutta-percha cones. Gutta-percha was then down-packed and the root canal backfilled using the extruder hand-piece of the Elements Obturation System (SybronEndo, Orange, CA, USA). The teeth were assigned to two groups (n = 18), and removal of the root fillings was performed using one of the following techniques: group 1) ProTaper Universal retreatment files used with rotational motion (RM) and group 2) ProTaper Universal retreatment files used with adaptive motion (AM) (600° clockwise/0° counter-clockwise to 370° clockwise/50° counter-clockwise). The teeth were sectioned, and both halves were analysed at 8 × magnification. The percentage of remaining filling material was recorded. The data were analysed statistically using the Student's t-test at a 95% confidence level (P ProTaper Universal retreatment files with adaptive motion removed more filling materials from root canals than the rotational movement. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

The X-ray fluorescent method for determination of total sulphur in bituminous coals

International Nuclear Information System (INIS)

Widowska-Kusmierska, J.; Siess, K.

1979-01-01

The X-ray fluorescent technique for the determination of total sulphur covering concentrations from 0,1 to 10% has been applied for bituminous coals showing a great variability in qualitative and quantitative composition of mineral matter (ash). The described method is a quick one giving results during one hour. The obtained good accuracy of determinations gives prospects for wide industrial application. (author)

Long-term properties of TVO's bituminized resins

International Nuclear Information System (INIS)

Valkiainen, M.; Vuorinen, U.

1989-06-01

Long-term properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied since 1981. This report summarizes the results on water uptake and leaching obtained up till now. It is observed that water uptake in excess of rewetting of the ion-exchange resins is taking place. Leach test in water equilibrated with cement have been performed for about five years. Separation of granular resin particles caused by density differences observed in former experiments was further studied and confirmed in this work. Anaerobic corrosion of a steel drum has been studied in laboratory conditions generally giving corrosion rates below l μm/a. Radiolytic gases will accumulate and be trapped in the waste product. The rate of swelling is estimated by a specially constructed device based on ultrasonic distance meter observing changes in level of the product surface in the drum

Application of infrared camera to bituminous concrete pavements: measuring vehicle

Science.gov (United States)

Janků, Michal; Stryk, Josef

2017-09-01

Infrared thermography (IR) has been used for decades in certain fields. However, the technological level of advancement of measuring devices has not been sufficient for some applications. Over the recent years, good quality thermal cameras with high resolution and very high thermal sensitivity have started to appear on the market. The development in the field of measuring technologies allowed the use of infrared thermography in new fields and for larger number of users. This article describes the research in progress in Transport Research Centre with a focus on the use of infrared thermography for diagnostics of bituminous road pavements. A measuring vehicle, equipped with a thermal camera, digital camera and GPS sensor, was designed for the diagnostics of pavements. New, highly sensitive, thermal cameras allow to measure very small temperature differences from the moving vehicle. This study shows the potential of a high-speed inspection without lane closures while using IR thermography.

Impact reduction of the uncertain geometrical parameters on magnetic material identification of an EI electromagnetic inductor using an adaptive inverse algorithm

International Nuclear Information System (INIS)

Abdallh, A.; Crevecoeur, G.; Dupré, L.

2012-01-01

The magnetic characteristics of the electromagnetic devices' core materials can be recovered by solving an inverse problem, where sets of measurements need to be properly interpreted using a forward numerical model of the device. However, the uncertainties of the geometrical parameter values in the forward model lead to appreciable recovery errors in the recovered values of the material parameters. In this paper, we propose an effective inverse approach technique, in which the influences of the uncertainties in the geometrical model parameters are minimized. In this proposed approach, the cost function that needs to be minimized is adapted with respect to the uncertain geometrical model parameters. The proposed methodology is applied onto the identification of the magnetizing B–H curve of the magnetic material of an EI core inductor. The numerical results show a significant reduction of the recovery errors in the identified magnetic material parameter values. Moreover, the proposed methodology is validated by solving an inverse problem starting from real magnetic measurements. - Highlights: ► A new method to minimize the influence of the uncertain parameters in inverse problems is proposed. ► The technique is based on adapting iteratively the objective function that needs to be minimized. ► The objective function is adapted by the model response sensitivity to the uncertain parameters. ► The proposed technique is applied for recovering the B–H curve of an EI core inductor material. ► The error in the inverse problem solution is dramatically reduced using the proposed methodology.

Use for refuse of shale carbonization

Energy Technology Data Exchange (ETDEWEB)

1917-09-25

A process is disclosed for using the refuse from the carbonization of bituminous shales in the preparation of light building material, characterized in that the pulverized material is mixed wet with a light filler, formed in a mold, and burned with or without the addition of clay or with the addition of binding and preserving material, preparing the mold from the pulverized material in the cold.

Effects of culture-sensitive adaptation of patient information material on usefulness in migrants: a multicentre, blinded randomised controlled trial.

Science.gov (United States)

Hölzel, Lars P; Ries, Zivile; Kriston, Levente; Dirmaier, Jörg; Zill, Jördis M; Rummel-Kluge, Christine; Niebling, Wilhelm; Bermejo, Isaac; Härter, Martin

2016-11-23

To evaluate the usefulness of culture-sensitive patient information material compared with standard translated material. Multicentre, double-blind randomised controlled trial. 37 primary care practices. 435 adult primary care patients with a migration background with unipolar depressive disorder or non-specific chronic low back pain were randomised. Patients who were unable to read in the language of their respective migration background were excluded. Sufficient data were obtained from 203 women and 106 men. The largest group was of Russian origin (202 patients), followed by those of Turkish (52), Polish (30) and Italian (25) origin. Intervention group: provision of culture-sensitive adapted material. provision of standard translated material. Primary outcome: patient-rated usefulness (USE) assessed immediately after patients received the material. patient-rated usefulness after 8 weeks and 6 months, symptoms of depression (PHQ-9), back pain (Back Pain Core Set) and quality of life (WHO-5) assessed at all time points. Usefulness was found to be significantly higher (t=1.708, one-sided p=0.04) in the intervention group (USE-score=65.08, SE=1.43), compared with the control group (61.43, SE=1.63), immediately after patients received the material, in the intention-to-treat analysis, with a mean difference of 3.65 (one-sided 95% lower confidence limit=0.13). No significant differences were found for usefulness at follow-up (p=0.16, p=0.71). No significant effect was found for symptom severity in depression (p=0.95, p=0.66, p=0.58), back pain (p=0.40, p=0.45, p=0.32) or quality of life (p=0.76, p=0.86, p=0.21), either immediately after receiving the material, or at follow-up (8 weeks; 6 months). Patients with a lower level of dominant society immersion benefited substantially and significantly more from the intervention than patients with a high level of immersion (p=0.005). Cultural adaptation of patient information material provides benefits over high quality

Studies on preparation and adaptive thermal control performance of novel PTC (positive temperature coefficient) materials with controllable Curie temperatures

International Nuclear Information System (INIS)

Cheng, Wen-long; Yuan, Shuai; Song, Jia-liang

2014-01-01

PTC (positive temperature coefficient) material is a kind of thermo-sensitive material. In this study, a series of novel PTC materials adapted to thermal control of electron devices are prepared. By adding different low-melting-point blend matrixes into GP (graphite powder)/LDPE (low density polyethylene) composite, the Curie temperatures are adjusted to 9 °C, 25 °C, 34 °C and 41 °C, and the resistance–temperature coefficients are enhanced to 1.57/°C–2.15/°C. These PTC materials remain solid in the temperature region of PTC effect, which makes it possible to be used as heating element to achieve adaptive temperature control. In addition, the adaptive thermal control performances of this kind of materials are investigated both experimentally and theoretically. The result shows that the adaptive effect becomes more significant while the resistance–temperature coefficient increases. A critical heating power defined as the initial heating power which makes the equilibrium temperature reach terminal temperature is presented. The adaptive temperature control will be effective only if the initial power is below this value. The critical heating power is determined by the Curie temperature and resistance–temperature coefficient of PTC materials, and a higher Curie temperature or resistance–temperature coefficient will lead to a larger critical heating power. - Highlights: • A series of novel PTC (positive temperature coefficient) materials were prepared. • The Curie point of PTC material can be adjusted by choosing different blend matrixes. • The resistance–temperature coefficient of PTC materials is enhanced to 2.15/°C. • The material has good adaptive temperature control ability with no auxiliary method. • A mathematical model is established to analyze the performance and applicability

Influence of metal additives on pyrolysis behavior of bituminous coal by TG-FTIR analysis

Energy Technology Data Exchange (ETDEWEB)

Su, Wenjuan; Fang, Mengxiang; Cen, Jianmeng; Li, Chao; Luo, Zhongyang; Cen, Kefa [Zhejiang Univ., Hangzhou (China). State Key Lab. of Clean Energy Utilization

2013-07-01

To study the catalytic effects of alkali, alkaline earth and transition metal additives on coal pyrolysis behavior, bituminous coal loaded NaCl, KCl, CaCl{sub 2}, MgCl{sub 2}, FeCl{sub 3} and NiCl{sub 2} was respectively investigated using Thermogravimetry and Fourier Transform Infrared Spectroscopy (TG-FTIR). Results indicated that the maximum mass loss rate decreased under the metal additives in the primary pyrolysis stage. The total mass loss of pyrolysis was reduced in metals catalyzed pyrolysis except for Na loaded sample. Kinetic analysis was taken for all samples adopting the method of Coats-Redfern. Activation energy of raw coal in the primary pyrolysis stage was 92.15vkJ.mol{sup -1}, which was lowered to 44.59-73.42 kJ.mol{sup -1} under metal additives. The orders of catalytic effect for this bituminous coal were Mg > Fe > Ca > Ni > K > Na according to their activation energies. Several investigated volatiles including CH{sub 4}, CO{sub 2}, CO, toluene, phenol and formic acid were identified from FTIR spectra. The yields of CH{sub 4}, CO{sub 2}, toluene, phenol and formic acid were decreased, but the evolution of CO was increased. The presence of metals in the coal samples have been involved in a repeated bond-forming and bond-breaking process, which greatly hindered the release of tars during pyrolysis as the tar precursors were connected to coal/char matrix and were thermally cracked, becoming a part of char.

Co-combustion characteristics and blending optimization of tobacco stem and high-sulfur bituminous coal based on thermogravimetric and mass spectrometry analyses.

Science.gov (United States)

Zhang, Kaihua; Zhang, Kai; Cao, Yan; Pan, Wei-ping

2013-03-01

Despite much research on co-combustion of tobacco stem and high-sulfur coal, their blending optimization has not been effectively found. This study investigated the combustion profiles of tobacco stem, high-sulfur bituminous coal and their blends by thermogravimetric analysis. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions were also studied by thermogravimetric and mass spectrometry analyses. The results indicated that combustion of tobacco stem was more complicated than that of high-sulfur bituminous coal, mainly shown as fixed carbon in it was divided into two portions with one early burning and the other delay burning. Ignition and burnout performances, heat release performances, and gaseous pollutant emissions of the blends present variable trends with the increase of tobacco stem content. Taking into account the above three factors, a blending ratio of 0–20% tobacco stem content is conservatively proposed as optimum amount for blending. Copyright © 2012 Elsevier Ltd. All rights reserved.

Material and Social Construction: A Framework for the Adaptation of Buildings

Directory of Open Access Journals (Sweden)

Jesse M. Keenan

2014-12-01

Full Text Available This article is a formulation of a framework for understanding the nature of change, particularly climate change, as it applies to the scale of a building. Through an exploration of various scientific and social scientific literutre, the article positions the concept of adaptation as the appropriate mode for understanding and managing change. Through the classification of a duality of material and social construction in the ontological composition of a building, various lines of thought relating to adaptive capacity and adaptive cycling within systems theory are appropriated within an integrated framework for adaptation. Specifically, it is theorized that as buildings as objects are developing greater capacities for intergrated operations and management through artificial intelligence, they will possess an ex ante capacity to autonomously adapt in dynamic relation to and with the ex post adaptation of owners and operators. It is argued that this top-down and bottom-up confluence of multi-scalar dynamic change is consistent with the prevailing theory of Panarchy applied in social-ecological systems theory. The article concludes with normative perspectives on the limitations of systems theory in architecture, future directions for research and an alternative positioning of professional practices.

Supplementary material for: The adaptive synchronization of ...

Indian Academy of Sciences (India)

Supplementary material for: The adaptive synchronization of fractional-order Liu chaotic system with unknown parameters. ADELEH NOURIAN and SAEED BALOCHIAN. -50. -40. -30. -20. -10. 0. 10. 20. 30. 40. -25. -20. -15. -10. -5. 0. 5. 10. 15. 20. 25. Y. Z. -12. -10. -8. -6. -4. -2. 0. 2. 4. 6. 8. -25. -20. -15. -10. -5. 0. 5. 10. 15.

Thermo-mechanical behavior of bituminous mixtures at low temperatures. Links between the binder characteristics and the mix properties; Comportement thermomecanique des enrobes bitumeux a basses temperatures: relations entre les proprietes du liant et de l'enrobe

Energy Technology Data Exchange (ETDEWEB)

Olard, F.

2003-10-01

This thesis has been realized within the framework of a partnership between the Ecole Nationale des TPE, APPIA and EUROVIA. The company Total has also been associated to this project. The study deals with the thermo-mechanical behavior of bituminous materials at low temperatures. The aim is to establish the links between the characteristics of the binder and the properties of bituminous mixes at low temperatures, and to better understand the existing low-temperature parameters and criteria for binders (or to propose new ones), related to the in-situ behavior of bituminous mixtures. A large experimental campaign has been carried out so as to fulfill this goal. After a bibliographical study on the rheology and the thermo-mechanical properties of (pure or modified) binders, putties and mixes, the experimental campaign carried out both in the small strain domain and in the large strain domain, is presented. The low temperature behavior of binders has been evaluated with three common fundamental tests: i)the complex modulus determination, ii)the Bending Beam Rheometer and iii)the tensile strength at a constant strain rate and constant temperatures. A new three point bending test on pre-notched bitumen beams has also been developed at the ENTPE. The low-temperature fracture properties of bitumens were studied at constant temperatures and cross-head speeds considering the Linear Elastic Fracture Mechanics (LEFM) assumptions. The thermo-mechanical behavior of bituminous mixtures has been studied by performing i)complex modulus tests, ii)measurements of the coefficient of thermal dilatation and contraction, iii)tensile tests at constant temperatures and strain rates, and iv)Thermal Stress Restrained Specimen Tests. Apart from the determination of some pertinent links between binder and mix properties and discriminating characteristics with regard to the thermal cracking of bituminous mixes at low temperatures, the analysis has also consisted in modeling the behavior of

Simulation Research on Adaptive Control of a Six-degree-of-freedom Material-testing Machine

Directory of Open Access Journals (Sweden)

Dan Wang

2014-02-01

Full Text Available This paper presents an adaptive controller equipped with a stiffness estimation method for a novel material-testing machine, in order to alleviate the performance depression caused by the stiffness variance of the tested specimen. The dynamic model of the proposed machine is built using the Kane method, and kinematic model is established with a closed-form solution. The stiffness estimation method is developed based on the recursive least-squares method and the proposed stiffness equivalent matrix. Control performances of the adaptive controller are simulated in detail. The simulation results illustrate that the proposed controller can greatly improve the control performance of the target material-testing machine by online stiffness estimation and adaptive parameter tuning, especially in low-cycle fatigue (LCF and high-cycle fatigue (HCF tests.

Treating carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Pier, M

1929-08-26

To separate the constituents or conversion products, which are liquid or which liquefy when heated, from solid distillable carbonaceous materials such as coals, oil shales, or other bituminous substances, the initial materials are subjected to a destructive hydrogenation under mild conditions so that the formation of benzines is substantially avoided, after which the material is subjected to an extraction treatment with solvents. The constituents of high boiling point range, suitable for the production of lubricating oils and solid paraffins, obtained by the said destructive hydrogenation are separated off before or/and after the said extraction treatment.

Chemical and Pyrolytic Thermogravimetric Characterization of Nigerian Bituminous Coals

Directory of Open Access Journals (Sweden)

Nyakuma Bemgba Bevan

2016-12-01

Full Text Available The discovery of new coal deposits in Nigeria presents solutions for nation’s energy crises and prospects for socioeconomic growth and sustainable development. Furthermore, the quest for sustainable energy to limit global warming, climate change, and environmental degradation has necessitated the exploration of alternatives using cleaner technologies such as coal pyrolysis. However, a lack of comprehensive data on physico-chemical and thermal properties of Nigerian coals has greatly limited their utilization. Therefore, the physico-chemical properties, rank (classification, and thermal decomposition profiles of two Nigerian bituminous coals – Afuze (AFZ and Shankodi-Jangwa (SKJ – were examined in this study. The results indicate that the coals contain high proportions of C, H, N, S, O and a sufficiently high heating value (HHV for energy conversion. The coal classification revealed that the Afuze (AFZ coal possesses a higher rank, maturity, and coal properties compared to the Shankodi-Jangwa (SKJ coal. A thermal analysis demonstrated that coal pyrolysis in both cases occurred in three stages; drying (30-200 °C, devolatilization (200-600 °C, and char decomposition (600-1000 °C. The results also indicated that pyrolysis at 1000 °C is not sufficient for complete pyrolysis. In general, the thermochemical and pyrolytic fuel properties indicate that the coal from both places can potentially be utilized for future clean energy applications.

Study of thermal reactivity during bituminization of radioactive waste

International Nuclear Information System (INIS)

Mouffe, Sh.

2004-10-01

This work deals with the study of chemical reactions and phases transitions which can occur between magnesium nitrate, sodium nitrate, cobalt sulphur product, and nickel potassium ferrocyanide, when they are heated together during bituminization process of nuclear waste. The applied methodology associates a few techniques: temperature, enthalpy, and kinetics of reaction are determined by calorimetry, reaction products are characterised by chemical analyses, mass spectrometry and XRD analysis. Three fields of temperature and energy are observed in function of composition (one compound or a mixture of compounds). The study of reactions between NaNO 3 and cobalt sulphur product shows that the presence of water has got an effect on reaction temperature. The study of Mg(NO 3 ) 2 , 6 H 2 O and CoS shows an overlapping of different signals, and that the reaction rate is very slow (a few hours). (author)

Bituminization of biologically harmful wastes

International Nuclear Information System (INIS)

Freund, M.; Magyar, M.; Mozes, G.; Csikos, R.; Kristof, M.; Toth, L.; Hima, G.

1977-01-01

The invention claims the bitumenization of biologically harmful wastes, such as industrial wastes containing radioactive materials. These wastes containing water are transported from sludge basins, this either by gravity or by mechanical stirrino. into a suitably adapted absorption zone or to several parallel zones filled with bitumen heated to 100 to 250 degC. An inert gas is forced into the system foaming the zone contents. The foam phase is decomposed by the action of heat while water is evaporated and condensed. Bitumen containing dry matter of the radioactive wastes is discharged from the bottom part of the absorption zone and stored in a tank. (Kr)

Adaptive and active materials: selected papers from the ASME 2012 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS 12) (Stone Mountain, GA, USA, 19-21 September 2012)

Science.gov (United States)

Seelecke, Stefan; Erturk, Alper; Ounaies, Zoubeida; Naguib, Hani; Huber, John; Turner, Travis; Anderson, Iain; Philen, Michael; Baba Sundaresan, Vishnu

2013-09-01

The fifth annual meeting of the ASME/AIAA Smart Materials, Adaptive Structures and Intelligent Systems Conference (SMASIS) was held in beautiful Stone Mountain near Atlanta, GA. It is the conference's objective to provide an up-to-date overview of research trends in the entire field of smart materials systems. This was reflected in keynote speeches by Professor Eduard Arzt (Institute of New Materials and Saarland University, Saarbrücken, Germany) on 'Micro-patterned artificial 'Gecko' surfaces: a path to switchable adhesive function', by Professor Ray H Baughman (The Alan G MacDiarmid NanoTech Institute, University of Texas at Dallas) on 'The diverse and growing family of carbon nanotube and related artificial muscles', and by Professor Richard James (University of Minnesota) on 'The direct conversion of heat to electricity using multiferroic materials with phase transformations'. SMASIS 2012 was divided into eight symposia which span basic research, applied technological design and development, and industrial and governmental integrated system and application demonstrations. • SYMP 1. Development and characterization of multifunctional materials. • SYMP 2. Mechanics and behavior of active materials. • SYMP 3. Modeling, simulation and control of adaptive systems. • SYMP 4. Integrated system design and implementation. • SYMP 5. Structural health monitoring/NDE. • SYMP 6. Bio-inspired materials and systems. • SYMP 7. Energy harvesting. • SYMP 8. Structural and materials logic. This year we were particularly excited to introduce a new symposium on energy harvesting, which has quickly matured from a special track in previous years to an independent symposium for the first time. The subject cuts across fields by studying different materials, ranging from piezoelectrics to electroactive polymers, as well as by emphasizing different energy sources from wind to waves and ambient vibrations. Modeling, experimental studies, and technology applications all

Dependence of carbon dioxide sorption on the petrographic composition of bituminous coals from the Czech part of the Upper Silesian Basin, Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Zuzana Weishauptova; Ivana Sykorova [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Institute of Rock Structure and Mechanics

2011-01-15

The effect of the rank and of the maceral composition of bituminous coal on carbon dioxide sorption capacity was studied on the basis of samples from two coal mines (Darkov, CSM) from the Czech part of the Upper Silesian Basin. The samples from the two mines cover a small but very significant section of coalification within the transition zone between high-volatile bituminous A coal and medium-volatile bituminous coal, where porosity and sorption properties pass through their minima. The coal porous system was characterized by the micropore volume evaluated using the sorption isotherm of carbon dioxide and the volumes of meso-, macro- and coarse pores were determined by high-pressure mercury porosimetry. The micropore fraction in the coal porous system ranged between 53% and 75%. It was particularly high in coals with high vitrinite content, namely collotelinite, and also in coals with high inertinite content. The carbon dioxide sorption capacity was determined from the carbon dioxide sorption isotherms measured using a gravimetric sorption analyzer at 298 K until a relative pressure of 0.015 p/p{sub s}, and was interpreted by characteristic parameters of the Dubinin and Langmuir equations. It was found that the adsorbed amount of CO{sub 2} in the CSM coal increases with the content of vitrinite and collotelinite, whereas no increase or only a slight increase was observed for the Darkov coal. The tendency of adsorption capacity to depend on maceral composition, and also to some extent on coalification, observed for the CSM coal, may be related to higher microporosity due to the coalification process or oxidative processes leading to the formation of pseudovitrinite. 42 refs., 8 figs., 4 tabs.

Cultural Adaptation and Translation of Outreach Materials on Autism Spectrum Disorder

Science.gov (United States)

Grinker, Roy R.; Kang-Yi, Christina D.; Ahmann, Chloe; Beidas, Rinad S.; Lagman, Adrienne; Mandell, David S.

2015-01-01

In order to connect with families and influence treatment trajectories, outreach materials should address cultural perceptions of the condition, its causes, and post-diagnostic care. This paper describes the cultural adaptation and translation of the Autism Speaks First 100 Days Kit into Korean for the purpose of improving autism spectrum disorder…

Low-temperature tar from bituminous coal and its further treatment

Energy Technology Data Exchange (ETDEWEB)

Hansen, C J

1950-01-01

High-temperature carbonization of bituminous coal yields only 3 to 4 percent tar, as compared with 8 to 10 percent or even more for low-temperature carbonization. The yield of phenols is 20 to 30 times as great from the low-temperature tar. Five conditions that must be met by a satisfactory low-temperature carbonization process are listed. The only method that satisfies all of these conditions is the Brennstoff-Technik (BT) process, in which iron retorts with movable walls are used. One disadvantage of most of the other processes is the high-pitch content of the tar. These tars are processed further to a neutral oil and a phenol-containing oil which are good diesel fuels with high-cetane numbers; the neutral oil can be fractionated to give oils of high-, medium-, and low-cetane number. Attempts to fractionate the tar oil by solvents have not proved commercially useful. However, the tar can be diluted with low-temperature light oil and phenols extracted with NaOH solution without distillation. Some difficulty is found, owing to the simultaneous extraction of viscous resins and other products that are readily removed from the phenols by distillation.

Determination of ultratrace levels of mercury in three SRMs by combustion RNAA

International Nuclear Information System (INIS)

Norman, B.R.; Becker, D.A.

2000-01-01

A radiochemical neutron activation analysis (RNAA) combustion method coupled with a neutron exposure normalization technique was used to determine low μg/kg mercury levels in three National Institute of Standards and Technology (NIST) Standard Reference Materials (SRMs). Two coals (sub-bituminous and bituminous) and a diet material were analyzed. The results obtained provided recommended values of approximately 5 μg/kg for SRM 1548a Typical Diet, 24 μg/kg for SRM 1635 Trace Elements in Coal (sub-bituminous), and 100 μg/kg for SRM 1632b Trace Elements in Coal (bituminous). (author)

Materials learning from life: concepts for active, adaptive and autonomous molecular systems.

Science.gov (United States)

Merindol, Rémi; Walther, Andreas

2017-09-18

Bioinspired out-of-equilibrium systems will set the scene for the next generation of molecular materials with active, adaptive, autonomous, emergent and intelligent behavior. Indeed life provides the best demonstrations of complex and functional out-of-equilibrium systems: cells keep track of time, communicate, move, adapt, evolve and replicate continuously. Stirred by the understanding of biological principles, artificial out-of-equilibrium systems are emerging in many fields of soft matter science. Here we put in perspective the molecular mechanisms driving biological functions with the ones driving synthetic molecular systems. Focusing on principles that enable new levels of functionalities (temporal control, autonomous structures, motion and work generation, information processing) rather than on specific material classes, we outline key cross-disciplinary concepts that emerge in this challenging field. Ultimately, the goal is to inspire and support new generations of autonomous and adaptive molecular devices fueled by self-regulating chemistry.

Properties and long-term behaviour of bitumen and radioactive waste-bitumen mixtures

International Nuclear Information System (INIS)

Eschrich, H.

1980-10-01

Part I represents a survey of the properties and the long-term behaviour of pure bitumens and mixtures of bitumens with radioactive reactor and reprocessing wastes. This survey includes information on the origin, amounts, and composition of the various wastes considered for bituminization and the different waste bituminization techniques used. The influence of various factors on the quality of waste-bitumen products and on the radiological safety during transport, short- and long-term storage of the final products is described. Special consideration is given to the most important safety relevant factors associated to the use of bitumen as matrix material for radioactive wastes, such as leach-resistance, radiolysis, chemical and mechanical stability, combustibility, and microbial attack. Part II consists of a comprehensive bibliography on the bituminization of radioactive wastes, giving about 300 references to literature published from the beginning of the use of bitumen in radioactive waste management in 1960 until the beginning of 1979. Methods for the quality control of bituminous materials and some useful data are given in an annex. (author)

Systems and methods for neutron detection using scintillator nano-materials

Science.gov (United States)

Letant, Sonia Edith; Wang, Tzu-Fang

2016-03-08

In one embodiment, a neutron detector includes a three dimensional matrix, having nanocomposite materials and a substantially transparent film material for suspending the nanocomposite materials, a detector coupled to the three dimensional matrix adapted for detecting a change in the nanocomposite materials, and an analyzer coupled to the detector adapted for analyzing the change detected by the detector. In another embodiment, a method for detecting neutrons includes receiving radiation from a source, converting neutrons in the radiation into alpha particles using converter material, converting the alpha particles into photons using quantum dot emitters, detecting the photons, and analyzing the photons to determine neutrons in the radiation.

Adaptive all the way down: building responsive materials from hierarchies of chemomechanical feedback.

Science.gov (United States)

Grinthal, Alison; Aizenberg, Joanna

2013-09-07

A living organism is a bundle of dynamic, integrated adaptive processes: not only does it continuously respond to constant changes in temperature, sunlight, nutrients, and other features of its environment, but it does so by coordinating hierarchies of feedback among cells, tissues, organs, and networks all continuously adapting to each other. At the root of it all is one of the most fundamental adaptive processes: the constant tug of war between chemistry and mechanics that interweaves chemical signals with endless reconfigurations of macromolecules, fibers, meshworks, and membranes. In this tutorial we explore how such chemomechanical feedback - as an inherently dynamic, iterative process connecting size and time scales - can and has been similarly evoked in synthetic materials to produce a fascinating diversity of complex multiscale responsive behaviors. We discuss how chemical kinetics and architecture can be designed to generate stimulus-induced 3D spatiotemporal waves and topographic patterns within a single bulk material, and how feedback between interior dynamics and surface-wide instabilities can further generate higher order buckling and wrinkling patterns. Building on these phenomena, we show how yet higher levels of feedback and spatiotemporal complexity can be programmed into hybrid materials, and how these mechanisms allow hybrid materials to be further integrated into multicompartmental systems capable of hierarchical chemo-mechano-chemical feedback responses. These responses no doubt represent only a small sample of the chemomechanical feedback behaviors waiting to be discovered in synthetic materials, and enable us to envision nearly limitless possibilities for designing multiresponsive, multifunctional, self-adapting materials and systems.

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; MacPhee, J.A.; Vancea, L.; Ciavaglia, L.A.; Nandi, B.N.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500 C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by N.M.R. and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars. (19 refs.)

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Ciavaglia, L.A.; MacPhee, J.A.; Nandi, B.N.; Vancea, L.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500/sup 0/C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by n.m.r., and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars.

Effect of ultrasonic agitation on push-out bond strength and adaptation of root-end filling materials.

Science.gov (United States)

Alcalde, Murilo Priori; Vivan, Rodrigo Ricci; Marciano, Marina Angélica; Duque, Jussaro Alves; Fernandes, Samuel Lucas; Rosseto, Mariana Bailo; Duarte, Marco Antonio Hungaro

2018-05-01

This study evaluated the effect of ultrasonic agitation of mineral trioxide aggregate (MTA), calcium silicate-based cement (CSC), and Sealer 26 (S26) on adaptation at the cement/dentin interface and push-out bond strength. Sixty maxillary canines were divided into 6 groups ( n = 10): MTA, S26, and CSC, with or without ultrasonic activation (US). After obturation, the apical portions of the teeth were sectioned, and retrograde cavities were prepared and filled with cement by hand condensation. In the US groups, the cement was activated for 60 seconds: 30 seconds in the mesio-distal direction and 30 seconds in the buccal-lingual direction, using a mini Irrisonic insert coupled with the ultrasound transducer. After the materials set, 1.5-mm thick sections were obtained from the apexes. The presence of gaps and the bond between cement and dentin were analyzed using low-vacuum scanning electron microscopy. Push-out bond strength was measured using a universal testing machine. Ultrasonic agitation increased the interfacial adaptation of the cements. The S26 US group showed a higher adaptation value than MTA ( p < 0.05). US improved the push-out bond strength for all the cements ( p < 0.05). The US of retrograde filling cements enhanced the bond to the dentin wall of the root-end filling materials tested.

Bituminous solidification, disposal, transport and burial of spent ion-exchange resins. Part of a coordinated programme on treatment of spent ion exchange resins

International Nuclear Information System (INIS)

Mozes, G.; Kristof, M.

1983-07-01

The project dealing with the incorporation of spent ion-exchange resins into bitumen was performed within the Agency coordinated research programme on treatment of spent ion-exchange resins. Physical and chemical properties of commercial ion-exchange resins, bitumens and bituminized resins were studied. It was shown that bitumen with low oil content and with a softening point of 60-70 deg. C are applicable for the incorporation of resins. The final waste form is allowed to contain maximum 50% resin. The comprehensive study of the biological resistance of B-30 bitumen was performed. That showed that any bacteriological attack can be regarded as generally insignificant. A continuously operating technology was realized on a semi-plant scale. The best operating conditions of this technology were determined. On the basis of the experience gained from the experiments a design of the bituminization plant of 50m 3 dry resin/year treatment capacity was proposed

Analysis of Porous Structure Parameters of Biomass Chars Versus Bituminous Coal and Lignite Carbonized at High Pressure and Temperature—A Chemometric Study

Directory of Open Access Journals (Sweden)

Adam Smoliński

2017-09-01

Full Text Available The characteristics of the porous structure of carbonized materials affect their physical properties, such as density or strength, their sorption capacity, and their reactivity in thermochemical processing, determining both their applicability as fuels or sorbents and their efficiency in various processes. The porous structure of chars is shaped by the combined effects of physical and chemical properties of a carbonaceous material and the operating parameters applied in the carbonization process. In the study presented, the experimental dataset covering parameters of various fuels, ranging from biomass through lignite to bituminous coal, and chars produced at 1273 K and under the pressure of 1, 2, 3, and 4 MPa was analyzed with the application of the advanced method of data exploration. The principal component analysis showed that the sample of the highest coal rank was characterized by lower values of parameters reflecting the development of the porous structure of chars. A negative correlation was also observed between the carbon content in a fuel and the evolution of the porous structure of chars at high pressure. The highest total pore volume of chars produced under 1 and 3 MPa and the highest micropore surface area under 3 MPa were reported for a carbonized fuel sample of the highest moisture content.

Fire and explosion incident at bituminization demonstration facility of PNC Tokai works, on march 11, 1997

International Nuclear Information System (INIS)

Miura, A.; Sato, Y.; Koyama, T.; Omori, E.; Kato, Y.; Suzuki, H.; Norjiri, I.; Yamanouchi, T.

2001-01-01

On March 11, a fire and explosion incident occurred at the Bituminization Demonstration Facility (BDF) of Tokai Reprocessing Plant in Power Reactor and Nuclear Fuel Development Corporation (PNC). Soon after the incident, PNC (now reorganized to JNC) started to investigate the facility damage, operational records around the incident, technical notes including facility design and reviews of R and D results, operators witness and to perform several analysis, tests and calculations. This paper describes outline and cause of the incident which were concluded based on the results of continuous serious investigation, analysis and calculation. (author)

Possibilities to improve the adaptation quality of calculated material substitutes

Energy Technology Data Exchange (ETDEWEB)

Geske, G.

1981-04-01

In calculating the composition of material substitutes by a system of simultaneous equations it is possible, by using a so called quality index, to find out of the set of solutions which generally exists that solution which possesses the best adaptation quality. Further improvement is often possible by describing coherent scattering and photoelectric interaction by an own material parameter for each effect. The exact formulation of these quantities as energy indepedent functions is, however, impossible. Using a set of attenuation coefficients at suitably chosen energies as coefficients for the system of equations the best substitutes are found. The solutions for the investigated example are identical with the original relative to its chemical composition. Such solutions may be of use in connection with neutrons, protons, heavy ions and negative pions. The components taken into consideration must, of course, permit such solutions. These facts are discussed in detail by two examples.

Improved process for the treatment of bituminous materials. [two heat treatments

Energy Technology Data Exchange (ETDEWEB)

1947-04-30

A continuous process for recovering valuable hydrocarbon oils from solid minerals adapted to produce such oils upon application of heat, consists of reducing the raw minerals to a powder, suspending the powdered minerals in a gaseous medium and subjecting the suspension thus formed to heat treatment in a primary reaction zone, followed by heat treatment in a secondary reaction zone separate from the primary reaction zone. The temperature during the second of said treatments being substantially higher than that of the first.

Inoculum density of Glomus mosseae and growth of onion plants in unsterilized bituminous coal spoil

Energy Technology Data Exchange (ETDEWEB)

Khan, A.G.

1988-01-01

The effect of inoculum, density (number of vesicular-arbuscular mycorrhizal (VAM) propagules g/sup -1/ of inoculum) on the growth of onions (Allium cepa L.) infected by Glomus mosseae (Nicol and Gerd). Gerdemann and Trappe, Comb nov in unsterilized coal spoil containing indigenous VAM fungi, including G. mosseae, was investigated. The amount of onion roots converted to mycorrhizas by inoculant fungus, estimated by a gridline intersect method, increased with inoculum density (..gamma..0.62, P0.05) until a plateau was reached. Onion growth responses also increased significantly (P<0.05) with the amount of VAM inoculum present in the coal spoil. The initial linear relationship between inoculum propagules (MPN estimates), percent colonization of onion roots and onion shoot dry weight became quadratic as the number of infection propagules increased. VAM infection had no significant effect on root:shoot ratios. Similarly there was no significant interaction (P>0.05) between the inoculum density, VAM-colonized root mass and the onion root:shoot fresh weight ratios. The amount of the windswept bituminous coal spoil bound to VAM (presumably because of VAM external hyphae) also increased as inoculum density increased (..gamma..0.63, P<0.05). There was a stronger correlation (ga0.85, P<0.05) between the amount of spoil adhered per plant and the root fresh wt plant/sup -1/ indicating that root effects were primarily responsible for increasing spoil adherence. There were negative correlations (P<0.05) between root fresh wt plant/sup -1/ (..gamma..-0.68), inoculum density (..gamma..-0.589), percent root elngth infected (..gamma..-0.73) and the amount of spoil adhered g/sup -1/ root fresh wt. The possible exploitation of VAM in revegetation of bituminous coal spoil is discussed. 25 refs., 2 tabs.

Co-gasification of bituminous coal and hydrochar derived from municipal solid waste: Reactivity and synergy.

Science.gov (United States)

Wei, Juntao; Guo, Qinghua; He, Qing; Ding, Lu; Yoshikawa, Kunio; Yu, Guangsuo

2017-09-01

In this work, the influences of gasification temperature and blended ratio on co-gasification reactivity and synergy of Shenfu bituminous coal (SF) and municipal solid waste-derived hydrochar (HTC) were investigated using TGA. Additionally, active alkaline and alkaline earth metal (AAEM) transformation during co-gasification was quantitatively analyzed by inductively coupled plasma optical emission spectrometer for correlating synergy on co-gasification reactivity. The results showed that higher char gasification reactivity existed at higher HTC char proportion and gasification temperature, and the main synergy behaviour on co-gasification reactivity was performed as synergistic effect. Enhanced synergistic effect at lower temperature was mainly resulted from more obviously inhibiting the primary AAEM (i.e. active Ca) transformation, and weak synergistic effect still existed at higher temperature since more active K with prominent catalysis was retained. Furthermore, more active HTC-derived AAEM remaining in SF sample during co-gasification would lead to enhanced synergistic effect as HTC char proportion increased. Copyright © 2017 Elsevier Ltd. All rights reserved.

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

Energy Technology Data Exchange (ETDEWEB)

Fischer, Hartmut R., E-mail: hartmut.fischer@tno.nl [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands); Dillingh, E.C.; Hermse, C.G.M. [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands)

2013-01-15

Highlights: Black-Right-Pointing-Pointer Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. Black-Right-Pointing-Pointer Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. Black-Right-Pointing-Pointer Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

International Nuclear Information System (INIS)

Fischer, Hartmut R.; Dillingh, E.C.; Hermse, C.G.M.

2013-01-01

Highlights: ► Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. ► Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. ► Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

Translation and adaptation of smoking relapse-prevention materials for pregnant and postpartum Hispanic women.

Science.gov (United States)

Simmons, Vani Nath; Cruz, Ligia M; Brandon, Thomas H; Quinn, Gwendolyn P

2011-01-01

Quitting smoking is one of the most important behavior changes a pregnant woman can make, with health benefits extending beyond pregnancy for the woman and her child. Increasing numbers of pregnant women are quitting smoking; however, the majority resume smoking later in their pregnancy or shortly after giving birth. Previous research has demonstrated the efficacy of self-help smoking relapse-prevention booklets; however, there is a dearth of materials available in Spanish for Hispanic smokers. The goal of the present study was to translate and adapt existing, theoretically based, smoking relapse-prevention materials for pregnant and postpartum Hispanic women. This article describes the transcreation approach used to ensure the Forever Free for Baby and Me booklets were linguistically and culturally relevant for the heterogeneous populations of Hispanic women. The authors conducted multistage formative research to adapt the booklets and modify vignettes and graphics. Compared with previous research conducted with pregnant non-Hispanic women, results revealed the following: (a) a lack of association or concern about smoking and weight gain, (b) the importance of family approval of behavior, and (c) stress related to difficulties surrounding the immigration experience. The authors' qualitative findings confirm and extend past research that has suggested ways to enhance the cultural relevance and acceptability of a health intervention.

Bituminization of simulated PWR type reactor wastes, boric evaporator bottons and ion exchange resins, carried out in CNEN/SP using commercial bitumen available in the Brazilian market

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1986-01-01

The first results of the study of bituminization of simulated PWR wastes, boric evaporator bottons and spent ion-exclange resins (OH - , H + ) and incinerated ash-wates are presented and discussed. The study consisted of characterization of the commercial bitumen, locally available and bitumen wastes products of varying whight compositions. The characterization was carried out using standard analysis methods of ABNT and ASTM, and included measurement of, penetration, softening point and flash point. In addition, the bitumen samples were analized for their resin and asphaltene contents. For leaching studies, wastes products of bitumen and resin loaded with 134 Cs were utilized. The method used was according to the ISO norms. The simulation of the industrial process was carried out using an extruder-evaporator typically used in the plastic industries offered by Industria de Maquinas Miotto Ltda., Sao Bernardo do Campo - SP. (Author) [pt

Modified composite material developed on the basis of no-fines asphalt concrete

Directory of Open Access Journals (Sweden)

Mikhasek Andrey

2017-01-01

Full Text Available Being a composite material, asphalt concrete is widely used in hydraulic engineering and road construction. The paper proves one of asphalt concrete modification, which includes first creating a skeleton of no-fines concrete and then its washing-down with bituminous materials by a hot procedure, can be successfully used in hydraulic structures Modified composite material based on no-fines asphalt concrete has a harder skeleton because of links from cement stone and has a technological advantage, as through the proposed technology it allows to reduce the cost of filling porous spaces. This technology allows to conclude that concrete aggregate with size fractions of 120 mm or less and frost resistance of 50 cycles and less can be recommended for fastening of slopes.

Nuclear magnetic resonance studies of ancient buried wood-II. Observations on the origin of coal from lignite to bituminous coal

Science.gov (United States)

Hatcher, P.G.; Breger, I.A.; Szeverenyi, N.; Maciel, G.E.

1982-01-01

Coalified logs ranging in age from Late Pennsylvania to Miocene and in rank from lignite B to bituminous coal were analyzed by 13C nuclear magnetic resonance (NMR) utilizing the cross-polarization, magic-angle spinning technique, as well as by infrared spectroscopy. The results of this study indicate that at least three major stages of coalification can be observed as wood gradually undergoes transformation to bituminous coal. The first stage involves hydrolysis and loss of cellulose from wood with retention and differential concentration of the resistant lignin. The second stage involves conversion of the lignin residues directly to coalified wood of lignitic rank, during which the oxygen content of intermediate diagenetic products remains constant as the hydrogen content and the carbon content increases. These changes are thought to involve loss of methoxyl groups, water, and C3 side chains from the lignin. In the third major stage of coalification, the coalified wood increases in rank to subbituminous and bituminous coal; during this stage the oxygen content decreases, hydrogen remains constant, and the carbon content increases. These changes are thought to result from loss of soluble humic acids that are rich in oxygen and that are mobilized during compaction and dewatering. Relatively resistant resinous substances are differentially concentrated in the coal during this stage. The hypothesis that humic acids are formed as mobile by-products of the coalification of lignin and function only as vehicles for removal of oxygen represents a dramatic departure from commonly accepted views that they are relatively low-molecular-weight intermediates formed during the degradation of lignin that then condense to form high-molecular-weight coal structures. ?? 1982.

Characterizing volumetric deformation behavior of naturally occuring bituminous sand materials

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2009-05-01

Full Text Available newly proposed hydrostatic compression test procedure. The test procedure applies field loading conditions of off-road construction and mining equipment to closely simulate the volumetric deformation and stiffness behaviour of oil sand materials. Based...

Adaptive and active materials: selected papers from the ASME 2013 Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS 13) (Snowbird, UT, USA, 16-18 September 2013)

Science.gov (United States)

Johnson, Nancy; Naguib, Hani; Turner, Travis; Anderson, Iain; Bassiri-Gharb, Nazanin; Daqaq, Mohammed; Baba Sundaresan, Vishnu; Sarles, Andy

2014-10-01

The sixth annual meeting of the ASME Smart Materials, Adaptive Structures and Intelligent Systems Conference (SMASIS) was held in the beautiful mountain encircled Snowbird Resort and Conference Center in Little Cottonwood Canyon near Salt Lake City, Utah. It is the conference's objective to provide an up-to-date overview of research trends in the entire field of smart materials systems in a friendly casual forum conducive to the exchange of ideas and latest results. As each year we strive to grow and offer new experiences, this year we included special focused topic tracks on nanoscale multiferroic materials and origami engineering. The cross-disciplinary emphasis was reflected in keynote speeches by Professor Kaushik Bhattacharya (California Institute of Technology) on 'Cyclic Deformation and the Interplay between Phase Transformation and Plasticity in Shape Memory Alloys', by Professor Alison Flatau (University of Maryland at College Park) on 'Structural Magnetostrictive Alloys: The Other Smart Material', and by Dr Leslie Momoda (Director of the Sensors and Materials Laboratories, HRL Laboratories, LLC, Malibu, CA) on 'Architecturing New Functional Materials: An Industrial Perspective'. SMASIS 2013 was divided into seven symposia which span basic research, applied technological design and development, and industrial and governmental integrated system and application demonstrations. SYMP 1. Development and Characterization of Multifunctional Materials. SYMP 2. Mechanics and Behavior of Active Materials. SYMP 3. Modeling, Simulation and Control of Adaptive Systems. SYMP 4. Integrated System Design and Implementation. SYMP 5. Structural Health Monitoring. SYMP 6. Bioinspired Smart Materials and Systems. SYMP 7. Energy Harvesting. Authors of selected papers in the materials areas (symposia 1, 2, and 6) as well as energy harvesting (symposium 7) were invited to write a full journal article on their presentation topic for publication in this special issue of Smart

System for the fixation of radioactive and/or toxic waste materials

International Nuclear Information System (INIS)

Meier, G.

1975-01-01

In a bituminization process with a double-screw extruder aqueous concentrates, slimes, and resins are treated. In order to improve the operational safety in each evaporation nozzle the sight windows are purified with steam provided by a steam pipe and the areas of the nozzles bordering on the extrusion screws by means of steam lances mounted on a distribution. In addition, two alternately operable filters of, e.g. oil separating material are arranged in the connecting pipe between condenser and distillate collector in order to collect spatters of bitumen. During change of the receiving vessel for the mixed material, an interruption pot collecting the remains of the emerging mixed material is mounted on the filling nipple of the extruder. (DG/PB) [de

Modular titanium alloy neck adapter failures in hip replacement - failure mode analysis and influence of implant material

Directory of Open Access Journals (Sweden)

Bloemer Wilhelm

2010-01-01

Full Text Available Abstract Background Modular neck adapters for hip arthroplasty stems allow the surgeon to modify CCD angle, offset and femoral anteversion intraoperatively. Fretting or crevice corrosion may lead to failure of such a modular device due to high loads or surface contamination inside the modular coupling. Unfortunately we have experienced such a failure of implants and now report our clinical experience with the failures in order to advance orthopaedic material research and joint replacement surgery. The failed neck adapters were implanted between August 2004 and November 2006 a total of about 5000 devices. After this period, the titanium neck adapters were replaced by adapters out of cobalt-chromium. Until the end of 2008 in total 1.4% (n = 68 of the implanted titanium alloy neck adapters failed with an average time of 2.0 years (0.7 to 4.0 years postoperatively. All, but one, patients were male, their average age being 57.4 years (36 to 75 years and the average weight 102.3 kg (75 to 130 kg. The failures of neck adapters were divided into 66% with small CCD of 130° and 60% with head lengths of L or larger. Assuming an average time to failure of 2.8 years, the cumulative failure rate was calculated with 2.4%. Methods A series of adapter failures of titanium alloy modular neck adapters in combination with a titanium alloy modular short hip stem was investigated. For patients having received this particular implant combination risk factors were identified which were associated with the occurence of implant failure. A Kaplan-Meier survival-failure-analysis was conducted. The retrieved implants were analysed using microscopic and chemical methods. Modes of failure were simulated in biomechanical tests. Comparative tests included modular neck adapters made of titanium alloy and cobalt chrome alloy material. Results Retrieval examinations and biomechanical simulation revealed that primary micromotions initiated fretting within the modular tapered neck

Report on the bituminous coal liquefaction sub-committee in fiscal 1992; 1992 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in the Sunshine Project in fiscal 1992. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant was launched in fiscal 1991. It is necessary to execute the pilot plant plan steadily in the future, and at the same time, reliably acquire different data by means of supportive researches. Economic performance of the process is also important. The first sub-committee meeting presented the following agenda: the status of constructing the 150-t/d pilot plant, tests and investigations thereon, research works by using a 1-t/d PSU, development of the most suitable coal refining technology, development of a coal pretreatment technology, improvement of the distilled oil distribution, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. The second sub-committee meeting presented the following agenda: the status of constructing the pilot plant, tests and investigations on improving the performance of natural pylite catalyst and circulating solvent, technological investigations on structuring a liquefying reaction data analyzing system, studies using a 1-t/d PSU, development of the most suitable coal refining technology, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. (NEDO)

Kinetics and equilibrium modeling of uranium(VI) sorption by bituminous shale from aqueous solution

International Nuclear Information System (INIS)

Ortaboy, Sinem; Atun, Gülten

2014-01-01

Highlights: • Oil shales are sedimentary rocks containing a polymeric matter in a mineral matrix. • Sorption potential of bituminous shale (BS) for uranium recovery was investigated. • U(VI) sorption increased with decreasing pH and increasing temperature. • Kinetic data were analyzed based on single and two resistance diffusion models. • The results fit well to the McKay equation assuming film and intraparticle diffusion. - Abstract: Sorption of U(VI) onto a bituminous shale (BS) from a nuclear power plant project site in Black Sea region was investigated for potential risk assessment when it releases into the environment with contaminated ground and surface water. The sorption characteristics of the BS for U(VI) recovery were evaluated as a function of contact time, adsorbent dosage, initial concentration, pH and temperature. Kinetic results fit better with pseudo-second-order model rather than pseudo-first-order. The possibility of diffusion process was analyzed based on Weber–Morris intra-particle diffusion model. The McKay equation assuming film- and intraparticle diffusion better predicted the data than the Vermeulen approximation presuming surface diffusion. Equilibrium sorption data were modeled according to the Langmuir, Dubinin–Radushkevich (D–R) and Freundlich isotherm equations. Sorption capacity increased from 0.10 to 0.15 mmol g −1 in 298–318 K temperature range. FT-IR analysis and pH dependent sorption studies conducted in hydroxide and carbonate media revealed that U(VI) species were sorbed in uranyl and its hydroxo forms on the BS. Desorption studies showed that U(VI) leaching with Black Sea water was negligible from the loaded BS. The activation parameters (E a , ΔH ∗ and ΔG ∗ ) estimated from diffusion coefficients indicated the presence of an energy barrier in the sorption system. However, thermodynamic functions derived from sorption equilibrium constants showed that overall sorption process was spontaneous in nature

An evidence for the strong association of N-methyl-2-pyrrolidinone with some organic species in three Chinese bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Liu, C.M.; Zong, Z.M.; Jia, J.X.; Liu, G.F.; Wei, X.Y. [China University of Mining and Technology, Xuzhou (China). School for Chemical Engineering

2008-04-15

Three Chinese bituminous coals collected from Shenfu, Heidaigou and Feicheng coal fields were respectively extracted with carbon-disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) mixed solvent (volume ratio 1:1) at room temperature followed by distillation of CS{sub 2} under ambient pressure and subsequent removal of most of NMP by distillation at 110{sup o}C under reduced pressure to afford mixed solvent-extractable fractions (MSEFs) with small amount of NMP. Acetone-extractable fraction 1 (AEF1) was obtained by extracting each MSEF under ultrasonic irradiation at room temperature and subsequently using a Soxhlet extractor. Direct extraction of each bituminous coal affords acetone-soluble fraction 2 (AEF2). GC/MS analysis shows that mlz of base or secondary peak in mass spectra of a series of components from each AEF1 is 98, whereas such components were not detected in AEF2. Since m/z of base peak in mass spectrum of NMP itself is 99, the base or secondary peak at m/z 98 should result from loss of a-H from NMP, i.e., NMP is strongly associated with some organic species (OSs) and thereby the components detected with base or secodary peak at m/z 98 in their mass spectra should be associated NMP-OS.

The effect of the textural properties of bituminous coal chars on NO emissions

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pis, J.J.; Jones, J.M.; Williams, A. [CSIC, Oviedo (Spain). Inst. Nacional del Carbon

1999-11-01

NO is the primary product of the oxidation of char nitrogen, and in some combustion processes the NO can be reduced on the char surface to give N{sub 2}O and/or N{sub 2}. In this study a range of bituminous coal (low, medium and high volatile matter content) were pyrolysed in a fixed bed reactor at various heating rates. Textural characterisation was carried out by measuring true (He) and apparent (Hg) densities and N{sub 2} (-196{degree}C) and CO{sub 2} (0{degree}C) adsorption isotherms. Pore volume distributions and surface areas were obtained for the chars studied. A thermogravimetric analyser coupled to a quadrupole mass spectrometer (TG-MS) was used to study the combustion behaviour of the samples and the nitrogen compounds evolved during temperature-programmed combustion. Results are discussed in terms of the influence of both textural properties and reactivity on NO emissions and on the heterogeneous reduction of NO. 23 refs., 8 figs., 4 tabs.

Use of fixation techniques in processing radioactive wastes from nuclear power plants in Czechoslovakia

International Nuclear Information System (INIS)

Seliga, M.

1977-01-01

The current state of radioactive waste disposal from the Bohunice nuclear power plant is described. The method of vacuum cementation was chosen for solidifying liquid radioactive wastes. This method makes it possible to obtain a product whose properties, namely strength, leachability, and radiation stability allow for the production of blocks without packing material. Also solved was the fixation of liquid radioactive waste using bituminization based on mixing liquid radioactive waste with aqueous bitumen emulsion in a film evaporator in which the mixture of liquid radioactive wastes and bitumen emulsion evaporate producing solid bitumen. The parameters are given of the cementation and bituminization lines which are designed for use in nuclear power plants with WWER type reactors. (J.B.)

Efecto de la tenacidad del asfalto en la resistencia a fatiga de las mezclas asfálticas Asphalt toughness effect on bituminous mixture fatigue behavior

Directory of Open Access Journals (Sweden)

Alfredo H Noguera

2011-08-01

Full Text Available Uno de los parámetros más importantes para definir el comportamiento de la mezcla en servicio es la tenacidad que el asfalto proporciona al aglomerar los agregados, es decir, la energía que se disipa al fracturar la mezcla, entre mayor sea dicha energía mejor será su calidad. Y por lo tanto, deberá existir una relación si dicha cantidad de energía se disipa en un ciclo de carga (tracción o con muchos ciclos durante el tiempo (fatiga. El objetivo de éste trabajo es establecer una relación entre la tenacidad que ofrecen distintos asfaltos y el comportamiento a fatiga de sus correspondientes mezclas asfálticas, para lo cual, se ha obtenido la tenacidad mediante un ensayo de tracción directa y se ha comparado con los valores de las leyes de fatiga y energía disipada obtenidas del ensayo de flexo-tracción dinámica.One of the most important parameters to define bituminous mixture behavior in service is the toughness that the bitumen provides when binding the aggregate particles; that is; the dissipated energy during the materials fracture process. The greater the dissipated energy in fracture, the better the bituminous mixture quality is. Hence, a relationship will have to exist if the toughness is removed during one load cycle (direct tension or during many cycles along time (fatigue. The purpose of this study is to determinate relationships between the toughness of different bitumens and the fatigue behavior of their corresponding bituminous mixtures, for which, the toughness has been obtained by means of direct tension test and has been compared with the value of the fatigue law and dissipated energy obtained by fatigue bending test. Results showed that, this study expect to give important means for further research to predict fatigue life from a static test.

Investigation on Adaptive Re-use of Heritage Building in George Town, Penang

Directory of Open Access Journals (Sweden)

Marhamah Abdul Hadi

2013-09-01

Full Text Available Adaptive re-use of heritage buildings in George Town has gained attention from their owners. Their owners either private owners or government, want to adapt their respective buildings to new usage for instance to become a gallery, museum, restaurant, boutique hotel and many more. Every heritage building that is being adapted to paper main objective is to identify the changes made in terms of structure, space and material when adapting the heritage buildings to a new usage specifically into a gallery. Two heritage buildings are chosen as case studies for this paper which are Rumah Teh Bunga and Fort Cornwallis; both buildings located in Penang, Malaysia. The changes made to these two buildings were analyzed using the guidelines provided which are Guideline for Conservation areas and Heritage Buildings and National Heritage Acts 2005. Both buildings will be analyzed using National Heritage Acts, while only Fort Cornwallis will be analyzed using Guideline for Conservation areas and Heritage Buildings. Adaptation of these two heritage buildings requires changes in structure, space and material. The changes in Rumah Teh Bunga focuses more on materials and space while changes in Fort Cornwallis emphasize more to space and addition of other structures. Analysis on the changes are made by using the guideline provided, most of the changes made to both of these heritage buildings comply the rules and regulations stated in the guideline. It was found from the data that some of the reasons on why the owner change Rumah Teh Bunga to gallery are because of its complicated procedure that involves in privatization of this building to other owner and the need to promote the heritage significance of this building to the public. As for Fort Cornwallis, the adaptation is more on strengthening its value as a fort and becoming a tourist attraction.

Development of advanced air-blown entrained-flow two-stage bituminous coal IGCC gasifier

Directory of Open Access Journals (Sweden)

Abaimov Nikolay A.

2017-01-01

Full Text Available Integrated gasification combined cycle (IGCC technology has two main advantages: high efficiency, and low levels of harmful emissions. Key element of IGCC is gasifier, which converts solid fuel into a combustible synthesis gas. One of the most promising gasifiers is air-blown entrained-flow two-stage bituminous coal gasifier developed by Mitsubishi Heavy Industries (MHI. The most obvious way to develop advanced gasifier is improvement of commercial-scale 1700 t/d MHI gasifier using the computational fluid dynamics (CFD method. Modernization of commercial-scale 1700 t/d MHI gasifier is made by changing the regime parameters in order to improve its cold gas efficiency (CGE and environmental performance, namely H2/CO ratio. The first change is supply of high temperature (900°C steam in gasifier second stage. And the second change is additional heating of blast air to 900°C.

Effect of processing on the rheological properties of poly-urethane/urea bituminous products

Energy Technology Data Exchange (ETDEWEB)

Carrera, V.; Partal, P.; Garcia-Morales, M.; Gallegos, C. [Dpto. Ingenieria Quimica, Facultad de Ciencias Experimentales, Campus de ' El Carmen' , Universidad de Huelva, 21071, Huelva (Spain); Perez-Lepe, A. [Technology Centre REPSOL YPF. Road N-V, Km 8, 28931, Mostoles (Spain)

2010-09-15

In this work, bitumen modification, by ''in situ'' formation of poly-urethane/urea-based polymers in the bituminous matrix, has been studied. This procedure consisted of a first modification by the addition of MDI-PPG reactive prepolymer (polypropylene-glycol, PPG, functionalized by polymeric MDI, 4,4'-diphenylmethane diisocyanate), in a first stage, and a further modification of the new bitumen-MDI-PPG molecules as water was added, in a second stage. Thin layer chromatography, TLC-FID, and infrared spectroscopy, FTIR, techniques have been used to follow the reactions occurring in four different types of bitumen. Rheological measurements have demonstrated that the resulting bitumen modification strongly depends on the processing conditions selected during the first stage. Thus, bitumen modification degree after water addition increases as processing time does. Furthermore, water addition has been found to promote bitumen foaming at low processing temperatures, which could be used in novel applications where a foamed binder is required. As a result, a reactive bitumen modification mechanism, involving a set of three chemical reactions, has been proposed. (author)

Use of various types of carbon-containing raw materials to produce thermal energy

Directory of Open Access Journals (Sweden)

В. Б. Кусков

2016-08-01

Full Text Available Many types of carbon-containing organic compounds and all possible carbon-containing products or wastes in low demand can be used to produce thermal energy. A technology has been developed for producing highly flammable briquettes on the basis of bituminous coal. These briquettes have a special incendiary layer. It is easily ignites from low energy heat sources (e.g. matches, and then flame spreads to the rest of briquette. Use of coal slacks and paper wastes as carbon-containing components playing the role of binders provides an opportunity to get a fuel briquette easy in terms of production and plain in composition while at the same time dispose of coal and paper wastes. Such briquettes may also have a special incendiary layer. Technology for fuel briquettes production from wood and slate wastes employed no binding agents, as wood products acted as binders. Thus technologies have been developed to produce fuel briquettes from various carbon-containing materials in low demand. The briquettes are intended for household boilers, fireplaces, different ovens in order to cook food, heat residential and utility premises, cabins, etc.

Active materials for automotive adaptive forward lighting Part 1: system requirements vs. material properties

Science.gov (United States)

Keefe, Andrew C.; Browne, Alan L.; Johnson, Nancy L.

2011-04-01

Adaptive Frontlighting Systems (AFS in GM usage) improve visibility by automatically optimizing the beam pattern to accommodate road, driving and environmental conditions. By moving, modifying, and/or adding light during nighttime, inclement weather, or in sharp turns, the driver is presented with dynamic illumination not possible with static lighting systems The objective of this GM-HRL collaborative research project was to assess the potential of active materials to decrease the cost, mass, and packaging volume of current electric stepper-motor AFS designs. Solid-state active material actuators, if proved suitable for this application, could be less expensive than electric motors and have lower part count, reduced size and weight, and lower acoustic and EMF noise1. This paper documents Part 1 of the collaborative study, assessing technically mature, commercially available active materials for use as actuators. Candidate materials should reduce cost and improve AFS capabilities, such as increased angular velocity on swivel. Additional benefits to AFS resulting from active materials actuators were to be identified as well such as lower part count. In addition, several notional approaches to AFS were documented to illustrate the potential function, which is developed more fully in Part 2. Part 1 was successful in verifying the feasibility of using two active materials for AFS: shape memory alloys, and piezoelectrics. In particular, this demonstration showed that all application requirements including those on actuation speed, force, and cyclic stability to effect manipulation of the filament assembly and/or the reflector could be met by piezoelectrics (as ultrasonic motors) and SMA wire actuators.