WorldWideScience

Sample records for acid affect bleaching

  1. Influence of Bleaching on Flavor of 34% Whey Protein Concentrate and Residual Benzoic Acid Concentration in Dried Whey Proteins

    Previous studies have shown that bleaching negatively affects the flavor of 70% whey protein concentrate (WPC70), but bleaching effects on lower-protein products have not been established. Benzoyl peroxide (BP), a whey bleaching agent, degrades to benzoic acid (BA) and may elevate BA concentrations...

  2. MOLYBDENUM CATALYZED ACID PEROXIDE BLEACHING OF EUCALYPTUS KRAFT PULP

    Marcos S. Rabelo; Jorge L. Colodette; Vera M. Sacon; Marcelo R. Silva; Marco A. B. Azevedo

    2008-01-01

    Molybdenum catalyzed peroxide bleaching (PMo Stage) consists of pulp treatment with hydrogen peroxide under acidic conditions in the presence of a molybdenum catalyst. Molybdenum is applied in catalytic doses (50-200 mg/kg pulp) and may originate from various sources, including (NH4)6Mo7O24.4H2O, Na2MoO4.2H2O, siliconmolybdate, etc. This work is aimed at optimizing the PMo stage and evaluating its industrial application in the OAZDP sequence. Optimum PMo stage conditions for bleaching eucalyp...

  3. Acid hydrolysis of cellulosic fibres: Comparison of bleached kraft pulp, dissolving pulps and cotton textile cellulose.

    Palme, Anna; Theliander, Hans; Brelid, Harald

    2016-01-20

    The behaviour of different cellulosic fibres during acid hydrolysis has been investigated and the levelling-off degree of polymerisation (LODP) has been determined. The study included a bleached kraft pulp (both never-dried and once-dried) and two dissolving pulps (once-dried). Additionally, cotton cellulose from new cotton sheets and sheets discarded after long-time use was studied. Experimental results from the investigation, together with results found in literature, imply that ultrastructural differences between different fibres affect their susceptibility towards acid hydrolysis. Drying of a bleached kraft pulp was found to enhance the rate of acid hydrolysis and also result in a decrease in LODP. This implies that the susceptibility of cellulosic fibres towards acid hydrolysis is affected by drying-induced stresses in the cellulose chains. In cotton cellulose, it was found that use and laundering gave a substantial loss in the degree of polymerisation (DP), but that the LODP was only marginally affected. PMID:26572472

  4. Effect of acid activation on structural and bleaching properties of a bentonite

    A natural bentonite obtained from Khorasan, Iran, was submitted to acid activation with sulphuric acid. Sample aliquots (5 gr) were leached with 100 ml H2SO4 solutions of various concentrations (2-7 N) at 80±2 degreeC for 2 hours. X-ray diffraction, chemical analysis, infrared spectroscopy and specific surface area measurements were performed in order to evaluate important structural modifications occurring as a result of acid attack. Octahedral sheet was affected by acid activation resulting into the dissolution of cations (Mg2+, Fe2+, Al3+) and consequent decomposition of montmorillonite structure. Bentonite samples were then tested in order to verify their capacity to bleach colza-soybean oil, and their performances were compared to that of a commercial bleaching clay. The bleaching ability of the natural clay was poor when compared with that of the industrial adsorbent. Acid activation of the bentonite sample with 7N sulphuric acid yielded an adsorbent material which was highly efficient in the bleaching of the oil functioned better than the commercial clay product under the same conditions.

  5. Corrosion Study of Stainless Steels in Peracetic Acid Bleach Media With and Without Chloride and Chelant

    Rohtash

    2014-12-01

    Full Text Available The paper industries are adopting non-chlorine containing chemicals e.g. peroxide, ozone, peracids etc. as alternate of chlorine based bleach chemicals e.g. chlorine and chlorine dioxide etc. with the aim of eco-friend atmospheres. Changeover to the new chemicals in the bleaching process is likely to affect the metallurgy of the existing bleach plants due to change in the corrosivity of the media. Accordingly, corrosion investigations were performed in a peracid namely peracetic acid to test the suitability of austenitic stainless steels 654SMO, 265SMO, 2205, 317L and 316L. The performance of above stainless steels was evaluated through long term immersion tests and Electrochemical polarization measurements in peracetic acid (PAA bleach media at pH value 4 maintaining concentration 0.2 % as active oxygen along with three chloride levels 0, 500 and 1000 ppm in pulp-free laboratory. To study the effect of corrosion inhibitors with extending limit of chloride in liquors, measurements were also made with two types of chelants- EDTA & MgSO4. The results showed that corrosivity of PAA reduced by addition of chelant while increased with concentration of Cl¯. The results also exhibited that EDTA is better inhibitor than MgSO4.

  6. ISOLATION OF PECTIC ACIDS FROM BLEACHED TMP WATER AND AGGREGATION OF MODEL AND TMP PECTIC ACIDS BY CALCIUM

    Anna C. Sundberg; Andrey V. Pranovich; Ville J. Saarimaa; Bjarne R. Holmbom

    2007-01-01

    Pectins are important structural elements in spruce fibres. Alkaline peroxide bleaching of spruce thermomechanical pulp (TMP) causes degradation and demethylation of pectins, yielding high-charge-density pectic acids. The pectic acids in fibres contribute strongly to the negative fibre charge, and the dissolved pectic acids increase the cationic demand of bleached TMP water. In this study, a method to isolate pectic acids from peroxide-bleached TMP pulp water is presented. The pectic acids we...

  7. MOLYBDENUM CATALYZED ACID PEROXIDE BLEACHING OF EUCALYPTUS KRAFT PULP

    Marcos S. Rabelo

    2008-08-01

    Full Text Available Molybdenum catalyzed peroxide bleaching (PMo Stage consists of pulp treatment with hydrogen peroxide under acidic conditions in the presence of a molybdenum catalyst. Molybdenum is applied in catalytic doses (50-200 mg/kg pulp and may originate from various sources, including (NH46Mo7O24.4H2O, Na2MoO4.2H2O, siliconmolybdate, etc. This work is aimed at optimizing the PMo stage and evaluating its industrial application in the OAZDP sequence. Optimum PMo stage conditions for bleaching eucalyptus pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/adt Mo and 5 kg/adt H2O2. The PMo stage was more efficient to remove pulp hexenuronic acids than lignin. Its efficiency decreased with increasing pH in the range of 1.5-5.5, while it increased with increasing temperature and peroxide and molybdenum doses. The application of the PMo stage as replacement for the A-stage of the AZDP sequence significantly decreased chlorine dioxide demand. The PMo stage caused a decrease of 20-30% in the generation of organically bound chlorine. The quality parameters of the pulp produced during the PMo stage mill trial were comparable to those obtained with the reference A-stage.

  8. Boring sponges, an increasing threat for coral reefs affected by bleaching events

    Carballo, José L; Bautista, Eric; Nava, Héctor; Cruz-Barraza, José A; Chávez, Jesus A

    2013-01-01

    Coral bleaching is a stress response of corals induced by a variety of factors, but these events have become more frequent and intense in response to recent climate-change-related temperature anomalies. We tested the hypothesis that coral reefs affected by bleaching events are currently heavily infested by boring sponges, which are playing a significant role in the destruction of their physical structure. Seventeen reefs that cover the entire distributional range of corals along the Mexican P...

  9. Corrosion Study of Stainless Steels in Peracetic Acid Bleach Media With and Without Chloride and Chelant

    Rohtash; Ajay K Singh; Rajendra Kumar

    2014-01-01

    The paper industries are adopting non-chlorine containing chemicals e.g. peroxide, ozone, peracids etc. as alternate of chlorine based bleach chemicals e.g. chlorine and chlorine dioxide etc. with the aim of eco-friend atmospheres. Changeover to the new chemicals in the bleaching process is likely to affect the metallurgy of the existing bleach plants due to change in the corrosivity of the media. Accordingly, corrosion investigations were performed in a peracid namely peracetic a...

  10. SIMULTANEOUS DETERMINATION OF CHLORINE DIOXIDE AND HYPOCHLOROUS ACID IN BLEACHING SYSTEM

    Qiang Wang

    2011-04-01

    Full Text Available This study has demonstrated a rapid spectroscopic method for the determination of chlorine dioxide and hypochlorous acid concentrations in the pulp bleaching processes. It was found that chlorine dioxide and hypochlorous acid have an isosbestic wavelength of 295 nm. The soluble lignin in such a system is the main interference, but can be corrected by determining the absorbances at 295 nm, 380 nm, and 480 nm. Thus, based on the spectroscopic measurements at 295 nm (the isosbestic point wavelength for chlorine dioxide and hypochlorous acid, 380 nm (absorbance wavelength of chlorine dioxide and 480 nm (the acid soluble lignin absorbance wavelength, the chlorine dioxide and hypochlorous acid concentrations in the bleaching process can be quantified. However, hypochlorous acid was not detected in the real bleaching effluent for its low content. The present method is simple, rapid, accurate, and has the potential for on-line monitoring of the chlorine dioxide bleaching process.

  11. Histological observations in the Hawaiian reef coral, Porites compressa, affected by Porites bleaching with tissue loss

    Sudek, M.; Work, T.M.; Aeby, G.S.; Davy, S.K.

    2012-01-01

    The scleractinian finger coral Porites compressa is affected by the coral disease Porites bleaching with tissue loss (PBTL). This disease initially manifests as bleaching of the coenenchyme (tissue between polyps) while the polyps remain brown with eventual tissue loss and subsequent algal overgrowth of the bare skeleton. Histopathological investigation showed a loss of symbiont and melanin-containing granular cells which was more pronounced in the coenenchyme than the polyps. Cell counts confirmed a 65% reduction in symbiont density. Tissue loss was due to tissue fragmentation and necrosis in affected areas. In addition, a reduction in putative bacterial aggregate densities was found in diseased samples but no potential pathogens were observed.

  12. Performance of an Argentinian acid-activated bentonite in the bleaching of soybean oil

    Foletto E.L.

    2003-01-01

    Full Text Available In this work, a bentonite clay from Mendoza, Argentina was activated with H2SO4 (4 and 8 N at 90ºC for 2 and 3.5 hours. Under these conditions several cations were removed from the octahedral sheet (Mg, Al, and Fe and the DTA-TGA curves of the solids obtained after treatment were modified. Treatment time and acid concentration increased the degree of destruction of the bentonite structure. Activated samples were tested in order to verify their capacity to bleach soybean oil and were compared to a standard commercial bleaching clay. Treated samples are more efficient in bleaching than the standard.

  13. Influence of pH, bleaching agents, and acid etching on surface wear of bovine enamel

    Soares, Ana Flávia; Bombonatti, Juliana Fraga Soares; Alencar, Marina Studart; Consolmagno, Elaine Cristina; Honório, Heitor Marques; Mondelli, Rafael Francisco Lia

    2016-01-01

    ABSTRACT Development of new materials for tooth bleaching justifies the need for studies to evaluate the changes in the enamel surface caused by different bleaching protocols. Objective The aim of this study was to evaluate the bovine dental enamel wear in function of different bleaching gel protocols, acid etching and pH variation. Material and Methods Sixty fragments of bovine teeth were cut, obtaining a control and test areas. In the test area, one half received etching followed by a bleaching gel application, and the other half, only the bleaching gel. The fragments were randomly divided into six groups (n=10), each one received one bleaching session with five hydrogen peroxide gel applications of 8 min, activated with hybrid light, diode laser/blue LED (HL) or diode laser/violet LED (VHL) (experimental): Control (C); 35% Total Blanc Office (TBO35HL); 35% Lase Peroxide Sensy (LPS35HL); 25% Lase Peroxide Sensy II (LPS25HL); 15% Lase Peroxide Lite (LPL15HL); and 10% hydrogen peroxide (experimental) (EXP10VHL). pH values were determined by a pHmeter at the initial and final time periods. Specimens were stored, subjected to simulated brushing cycles, and the superficial wear was determined (μm). ANOVA and Tukey´s tests were applied (α=0.05). Results The pH showed a slight decrease, except for Group LPL15HL. Group LPS25HL showed the highest degree of wear, with and without etching. Conclusion There was a decrease from the initial to the final pH. Different bleaching gels were able to increase the surface wear values after simulated brushing. Acid etching before bleaching increased surface wear values in all groups. PMID:27008254

  14. Influence of pH, bleaching agents, and acid etching on surface wear of bovine enamel

    Ana Flávia Soares

    2016-02-01

    Full Text Available ABSTRACT Development of new materials for tooth bleaching justifies the need for studies to evaluate the changes in the enamel surface caused by different bleaching protocols. Objective The aim of this study was to evaluate the bovine dental enamel wear in function of different bleaching gel protocols, acid etching and pH variation. Material and Methods Sixty fragments of bovine teeth were cut, obtaining a control and test areas. In the test area, one half received etching followed by a bleaching gel application, and the other half, only the bleaching gel. The fragments were randomly divided into six groups (n=10, each one received one bleaching session with five hydrogen peroxide gel applications of 8 min, activated with hybrid light, diode laser/blue LED (HL or diode laser/violet LED (VHL (experimental: Control (C; 35% Total Blanc Office (TBO35HL; 35% Lase Peroxide Sensy (LPS35HL; 25% Lase Peroxide Sensy II (LPS25HL; 15% Lase Peroxide Lite (LPL15HL; and 10% hydrogen peroxide (experimental (EXP10VHL. pH values were determined by a pHmeter at the initial and final time periods. Specimens were stored, subjected to simulated brushing cycles, and the superficial wear was determined (μm. ANOVA and Tukey´s tests were applied (α=0.05. Results The pH showed a slight decrease, except for Group LPL15HL. Group LPS25HL showed the highest degree of wear, with and without etching. Conclusion There was a decrease from the initial to the final pH. Different bleaching gels were able to increase the surface wear values after simulated brushing. Acid etching before bleaching increased surface wear values in all groups.

  15. Influence of pH, bleaching agents, and acid etching on surface wear of bovine enamel.

    Soares, Ana Flávia; Bombonatti, Juliana Fraga Soares; Alencar, Marina Studart; Consolmagno, Elaine Cristina; Honório, Heitor Marques; Mondelli, Rafael Francisco Lia

    2016-02-01

    Development of new materials for tooth bleaching justifies the need for studies to evaluate the changes in the enamel surface caused by different bleaching protocols. Objective The aim of this study was to evaluate the bovine dental enamel wear in function of different bleaching gel protocols, acid etching and pH variation. Material and Methods Sixty fragments of bovine teeth were cut, obtaining a control and test areas. In the test area, one half received etching followed by a bleaching gel application, and the other half, only the bleaching gel. The fragments were randomly divided into six groups (n=10), each one received one bleaching session with five hydrogen peroxide gel applications of 8 min, activated with hybrid light, diode laser/blue LED (HL) or diode laser/violet LED (VHL) (experimental): Control (C); 35% Total Blanc Office (TBO35HL); 35% Lase Peroxide Sensy (LPS35HL); 25% Lase Peroxide Sensy II (LPS25HL); 15% Lase Peroxide Lite (LPL15HL); and 10% hydrogen peroxide (experimental) (EXP10VHL). pH values were determined by a pHmeter at the initial and final time periods. Specimens were stored, subjected to simulated brushing cycles, and the superficial wear was determined (μm). ANOVA and Tukey´s tests were applied (α=0.05). Results The pH showed a slight decrease, except for Group LPL15HL. Group LPS25HL showed the highest degree of wear, with and without etching. Conclusion There was a decrease from the initial to the final pH. Different bleaching gels were able to increase the surface wear values after simulated brushing. Acid etching before bleaching increased surface wear values in all groups. PMID:27008254

  16. Improved microscopical detection of acid-fast bacilli by the modified bleach method in lymphnode aspirates

    Annam Vamseedhar

    2009-07-01

    Full Text Available Objectives: To improve the smear microscopy for detection of acid-fast bacilli (AFB in fine needle aspiration cytology (FNAC of lymph node using the bleach method and also to compare this with cytological diagnosis and the conventional Ziehl-Neelsen (ZN method. Study Design: In 99 consecutive patients with clinical suspicion of tuberculosis (TB presenting with lymphadenopathy, FNACs were performed. Smears from the aspirates were processed for routine cytology and the conventional ZN method. The remaining material in the needle hub and/or the syringe was used for the bleach method. The significance of the bleach method over the conventional ZN method and cytology was analyzed using the χ2 test. Results: Of 99 aspirates, 93 were studied and the remaining six were excluded from the study due to diagnosis of malignancy in 4.04% (4/6 and inadequate aspiration in 2.02% (2/6. Among the 93 aspirates, 33.33% (31/93 were positive for AFB on conventional ZN method, 41.94% (39/93 were indicative of TB on cytology and the smear positivity increased to 63.44% (59/93 on bleach method. Conclusion: The bleach method is simple, inexpensive and potent disinfectant, also limiting the risk of laboratory-acquired infections. The implementation of the bleach method clearly improves microscopic detection and can be a useful contribution to routine cytology.

  17. Effect of temperature and concentration on benzoyl peroxide bleaching efficacy and benzoic acid levels in whey protein concentrate.

    Smith, T J; Gerard, P D; Drake, M A

    2015-11-01

    Much of the fluid whey produced in the United States is a by-product of Cheddar cheese manufacture and must be bleached. Benzoyl peroxide (BP) is currently 1 of only 2 legal chemical bleaching agents for fluid whey in the United States, but benzoic acid is an unavoidable by-product of BP bleaching. Benzoyl peroxide is typically a powder, but new liquid BP dispersions are available. A greater understanding of the bleaching characteristics of BP is necessary. The objective of the study was to compare norbixin destruction, residual benzoic acid, and flavor differences between liquid whey and 80% whey protein concentrates (WPC80) bleached at different temperatures with 2 different benzoyl peroxides (soluble and insoluble). Two experiments were conducted in this study. For experiment 1, 3 factors (temperature, bleach type, bleach concentration) were evaluated for norbixin destruction using a response surface model-central composite design in liquid whey. For experiment 2, norbixin concentration, residual benzoic acid, and flavor differences were explored in WPC80 from whey bleached by the 2 commercially available BP (soluble and insoluble) at 5 mg/kg. In liquid whey, soluble BP bleached more norbixin than insoluble BP, especially at lower concentrations (5 and 10 mg/kg) at both cold (4°C) and hot (50°C) temperatures. The WPC80 from liquid whey bleached with BP at 50°C had lower norbixin concentration, benzoic acid levels, cardboard flavor, and aldehyde levels than WPC80 from liquid whey bleached with BP at 4°C. Regardless of temperature, soluble BP destroyed more norbixin at lower concentrations than insoluble BP. The WPC80 from soluble-BP-bleached wheys had lower cardboard flavor and lower aldehyde levels than WPC80 from insoluble-BP-bleached whey. This study suggests that new, soluble (liquid) BP can be used at lower concentrations than insoluble BP to achieve equivalent bleaching and that less residual benzoic acid remains in WPC80 powder from liquid whey

  18. SIMULTANEOUS DETERMINATION OF CHLORINE DIOXIDE AND HYPOCHLOROUS ACID IN BLEACHING SYSTEM

    Qiang Wang; Kefu Chen; Jun Li Mail; Jun Xu; Shanshan Liu Mail

    2011-01-01

    This study has demonstrated a rapid spectroscopic method for the determination of chlorine dioxide and hypochlorous acid concentrations in the pulp bleaching processes. It was found that chlorine dioxide and hypochlorous acid have an isosbestic wavelength of 295 nm. The soluble lignin in such a system is the main interference, but can be corrected by determining the absorbances at 295 nm, 380 nm, and 480 nm. Thus, based on the spectroscopic measurements at 295 nm (the isosbestic point wavelen...

  19. ISOLATION OF PECTIC ACIDS FROM BLEACHED TMP WATER AND AGGREGATION OF MODEL AND TMP PECTIC ACIDS BY CALCIUM

    Anna C. Sundberg

    2007-11-01

    Full Text Available Pectins are important structural elements in spruce fibres. Alkaline peroxide bleaching of spruce thermomechanical pulp (TMP causes degradation and demethylation of pectins, yielding high-charge-density pectic acids. The pectic acids in fibres contribute strongly to the negative fibre charge, and the dissolved pectic acids increase the cationic demand of bleached TMP water. In this study, a method to isolate pectic acids from peroxide-bleached TMP pulp water is presented. The pectic acids were isolated and purified in good yield using a polyacrylate resin to remove lignin, a cellulose filter to remove galactoglucomannans (GGM, and an anion exchange resin to separate pectic acids from neutral carbohydrates. Salts and residual low-molar-mass carbohydrates were further removed from the isolated pectic acids by dialysis. The isolated pectic acids (>80% purity had a low molar mass and a wide polydispersity (5.9 kDa, MW/MN 3.3. The aggregation and precipitation of the isolated pectic acids, as well as citrus fruit pectic acids with well-defined molar masses, by Ca2+-ions were studied. The molar mass of pectic acids was a key factor determining the precipitation of Ca2+-pectates. Pectic acids below 6 kDa were not precipitated by Ca2+, while higher molar masses led first to partial and then to complete precipitation. The precipitated Ca2+-pectates may impair paper machine runnability and paper quality.

  20. Gas Chromatography Analysis of Resin and Fatty Acids from Laboratory Generated Bleach Plant Effluents

    Chhaya Sharma; S. Mohanty; S. Kumar; N.J. Rao

    2007-01-01

    Laboratory generated spent bleached liquor from the chlorination, caustic extraction stage of mixed wood kraft pulp processing has been analyzed both qualitatively and quantitatively for various resin & fatty acids by using GC. A number of resin acids,saturated and unsaturated fatty acids, chloro fatty and resin acid have been detected and their concentrations are estimated. The results are compared with results on different agriculture residue/hardwood pulps, which were reported earlier. The concentrations of various compounds detected have also been compared with their reported LC50 values.

  1. Whiteness improvement of citric acid crosslinked cotton fabrics: H2O2 bleaching under alkaline condition.

    Tang, Peixin; Ji, Bolin; Sun, Gang

    2016-08-20

    Polycarboxylic acids have been employed as formaldehyde-free crosslinking agents in anti-wrinkle treatment for cotton fabrics. Cotton fabrics treated by citric acid (CA) catalyzed with effective catalysts have shown satisfactory anti-wrinkle properties. Meanwhile, CA is a natural-based and environmental friendly compound. However, the yellowing of CA treated fabrics is a stumbling block for its practical application. Due to the fact that CA firstly forms aconitic acid (AA) before forming anhydrides, the cause of the yellowing, hydrogen peroxide (H2O2) bleaching was adopted to treat the CA treated fabrics in order to break the CC bond structure and reduce the yellow color but retaining the desired anti-wrinkle properties. Thermogravimetric analysis and Fourier transformed infrared spectroscopy were employed to investigate the reactions. The results revealed that the H2O2 bleaching can effectively improve the whiteness and also maintain a good anti-wrinkle performance of the CA treated fabrics under an appropriate bleaching temperature and time. PMID:27178918

  2. IMPACT OF ACID WASHING AND CHELATION ON Mg(OH2-BASED HYDROGEN PEROXIDE BLEACHING OF MIXED HARDWOODS CMP AT A HIGH CONSISTENCY

    Somayeh Ghasemi

    2010-09-01

    Full Text Available The removal of transition metal ions is crucial for improving the efficiency of subsequent peroxide bleaching. Acid-washing and chelation have been proposed for such a purpose. However, their influences on the Mg(OH2-based peroxide bleaching of hardwood pulps at a high consistency have not been well documented in the literature. In this work, we studied the influence of acid-washing using sulfuric acid or chelation using diethylenetriaminepentaacetic (DTPA on the Mg(OH2- or NaOH-based hydrogen peroxide bleaching efficiency, effluent properties of bleaching filtrates, and paper properties. The results showed that for Mg(OH2-based peroxide bleaching, the pulp yield and water retention value of acid-washed pulp were higher than those of the chelated pulp; the chemical oxygen demand (COD and turbidity of the bleaching filtrates for the acid-washed pulp were lower than those of the chelated pulp. The bleached acid-washed pulp had lower strength properties than bleached chelated pulp did. Additionally, at a high pulp consistency (25%, the Mg(OH2-based process had a higher bleaching efficiency and superior bleaching effluent properties, but a lower strength properties, in comparison with the NaOH-based process.

  3. The Effect of Fiber Bleaching Treatment on the Properties of Poly(lactic acid)/Oil Palm Empty Fruit Bunch Fiber Composites

    Marwah Rayung; Nor Azowa Ibrahim; Norhazlin Zainuddin; Wan Zuhainis Saad; Nur Inani Abdul Razak; Buong Woei Chieng

    2014-01-01

    In this work, biodegradable composites from poly(lactic acid) (PLA) and oil palm empty fruit bunch (OPEFB) fiber were prepared by melt blending method. Prior to mixing, the fiber was modified through bleaching treatment using hydrogen peroxide. Bleached fiber composite showed an improvement in mechanical properties as compared to untreated fiber composite due to the enhanced fiber/matrix interfacial adhesion. Interestingly, fiber bleaching treatment also improved the physical appearance of th...

  4. Removal of hexenuronic acid by xylanase to reduce adsorbable organic halides formation in chlorine dioxide bleaching of bagasse pulp.

    Nie, Shuangxi; Wang, Shuangfei; Qin, Chengrong; Yao, Shuangquan; Ebonka, Johnbull Friday; Song, Xueping; Li, Kecheng

    2015-11-01

    Xylanase-aided chlorine dioxide bleaching of bagasse pulp was investigated. The pulp was pretreated with xylanase and followed a chlorine dioxide bleaching stage. The ATR-FTIR and XPS were employed to determine the surface chemistry of the control pulp, xylanase treated and chlorine dioxide treated pulps. The hexenuronic acid (HexA) could obviously be reduced after xylanase pretreatment, and the adsorbable organic halides (AOX) were reduced after chlorine dioxide bleaching. Compared to the control pulp, AOX could be reduced by 21.4-26.6% with xylanase treatment. Chlorine dioxide demand could be reduced by 12.5-22% to achieve the same brightness. The ATR-FTIR and XPS results showed that lignin and hemicellulose (mainly HexA) were the main source for AOX formation. Xylanase pretreatment could remove HexA and expose more lignin, which decreased the chlorine dioxide demand and thus reduced formation of AOX. PMID:26263004

  5. Bleach vs. Bacteria

    ... Articles | Inside Life Science Home Page Bleach vs. Bacteria By Sharon Reynolds Posted April 2, 2014 Your ... hypochlorous acid to help kill invading microbes, including bacteria. Researchers funded by the National Institutes of Health ...

  6. The Effect of Fiber Bleaching Treatment on the Properties of Poly(lactic acid/Oil Palm Empty Fruit Bunch Fiber Composites

    Marwah Rayung

    2014-08-01

    Full Text Available In this work, biodegradable composites from poly(lactic acid (PLA and oil palm empty fruit bunch (OPEFB fiber were prepared by melt blending method. Prior to mixing, the fiber was modified through bleaching treatment using hydrogen peroxide. Bleached fiber composite showed an improvement in mechanical properties as compared to untreated fiber composite due to the enhanced fiber/matrix interfacial adhesion. Interestingly, fiber bleaching treatment also improved the physical appearance of the composite. The study was extended by blending the composites with commercially available masterbatch colorant.

  7. The effect of fiber bleaching treatment on the properties of poly(lactic acid)/oil palm empty fruit bunch fiber composites.

    Rayung, Marwah; Ibrahim, Nor Azowa; Zainuddin, Norhazlin; Saad, Wan Zuhainis; Razak, Nur Inani Abdul; Chieng, Buong Woei

    2014-01-01

    In this work, biodegradable composites from poly(lactic acid) (PLA) and oil palm empty fruit bunch (OPEFB) fiber were prepared by melt blending method. Prior to mixing, the fiber was modified through bleaching treatment using hydrogen peroxide. Bleached fiber composite showed an improvement in mechanical properties as compared to untreated fiber composite due to the enhanced fiber/matrix interfacial adhesion. Interestingly, fiber bleaching treatment also improved the physical appearance of the composite. The study was extended by blending the composites with commercially available masterbatch colorant. PMID:25153628

  8. The Effect of Fiber Bleaching Treatment on the Properties of Poly(lactic acid)/Oil Palm Empty Fruit Bunch Fiber Composites

    Rayung, Marwah; Ibrahim, Nor Azowa; Zainuddin, Norhazlin; Saad, Wan Zuhainis; Razak, Nur Inani Abdul; Chieng, Buong Woei

    2014-01-01

    In this work, biodegradable composites from poly(lactic acid) (PLA) and oil palm empty fruit bunch (OPEFB) fiber were prepared by melt blending method. Prior to mixing, the fiber was modified through bleaching treatment using hydrogen peroxide. Bleached fiber composite showed an improvement in mechanical properties as compared to untreated fiber composite due to the enhanced fiber/matrix interfacial adhesion. Interestingly, fiber bleaching treatment also improved the physical appearance of the composite. The study was extended by blending the composites with commercially available masterbatch colorant. PMID:25153628

  9. BLEACHING EUCALYPTUS PULPS WITH SHORT SEQUENCES

    Flaviana Reis Milagres

    2011-03-01

    Full Text Available Eucalyptus spp kraft pulp, due to its high content of hexenuronic acids, is quite easy to bleach. Therefore, investigations have been made attempting to decrease the number of stages in the bleaching process in order to minimize capital costs. This study focused on the evaluation of short ECF (Elemental Chlorine Free and TCF (Totally Chlorine Free sequences for bleaching oxygen delignified Eucalyptus spp kraft pulp to 90% ISO brightness: PMoDP (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, PMoD/P (Molybdenum catalyzed acid peroxide, chlorine dioxide and hydrogen peroxide, without washing PMoD(PO (Molybdenum catalyzed acid peroxide, chlorine dioxide and pressurized peroxide, D(EPODP (chlorine dioxide, extraction oxidative with oxygen and peroxide, chlorine dioxide and hydrogen peroxide, PMoQ(PO (Molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide, and XPMoQ(PO (Enzyme, molybdenum catalyzed acid peroxide, DTPA and pressurized peroxide. Uncommon pulp treatments, such as molybdenum catalyzed acid peroxide (PMo and xylanase (X bleaching stages, were used. Among the ECF alternatives, the two-stage PMoD/P sequence proved highly cost-effective without affecting pulp quality in relation to the traditional D(EPODP sequence and produced better quality effluent in relation to the reference. However, a four stage sequence, XPMoQ(PO, was required to achieve full brightness using the TCF technology. This sequence was highly cost-effective although it only produced pulp of acceptable quality.

  10. Coral Bleaching

    Brinch, Anna; Hemmingsen, Sofie K. Møhlenfeldt; Rosenquist, Camilla; Tangaa, Stine Rosendal

    2010-01-01

    This review scrutinises the different cellular mechanisms and environmental stressors that lead to bleaching and discuss the numerous effects of these. Coral bleaching is characterized by corals losing their symbiotic zooxanthellae. Different environmental stressors, e.g. elevated sea temperatures, irradiance, changing salinity and increasing atmospheric CO2 induce damage in multiple sites of the photosynthetic apparatus of the zooxanthellae, leading to bleaching. Reactive oxygen species ...

  11. Peroxy bleaches

    Fabric laundering is now a sophisticated chemical process involving a variety of operations including bleaching. The chemistry of peroxy bleaches is described including the use of novel organic compounds to provide effective bleaching at the lower temperatures of modern wash cycles. The instability of peroxy compounds is illustrated using cameo case histories to relate theory and practice. Techniques available for determining their thermochemistry are summarised. A model is provided for hazard and risk assessment of development projects in general (particularly those involving new molecules, processes or formulations) from ideas phase through exploratory laboratory investigations to pilot plant scale-up and eventual manufacture and commercial exploitation. This paper is a prelude to Part 2, which describes the determination of thermodynamic and kinetic properties of peroxy bleaches and discusses the implication of the results in terms of precautions for their safe storage and incorporation into detergent formulations during processing

  12. Peroxy bleaches

    Carson, P.A. [Unilever Research, Port Sunlight Laboratory (United States) and Chemistry Department, University of Manchester, Institute of Science and Technology (United States)]. E-mail: pcarson2005@aol.com; Fairclough, C.S. [Unilever Research, Port Sunlight Laboratory (United States); Mauduit, C. [Chemistry Department, University of Manchester, Institute of Science and Technology (United States); Colsell, M. [Chemistry Department, University of Manchester, Institute of Science and Technology (United States)

    2006-08-25

    Fabric laundering is now a sophisticated chemical process involving a variety of operations including bleaching. The chemistry of peroxy bleaches is described including the use of novel organic compounds to provide effective bleaching at the lower temperatures of modern wash cycles. The instability of peroxy compounds is illustrated using cameo case histories to relate theory and practice. Techniques available for determining their thermochemistry are summarised. A model is provided for hazard and risk assessment of development projects in general (particularly those involving new molecules, processes or formulations) from ideas phase through exploratory laboratory investigations to pilot plant scale-up and eventual manufacture and commercial exploitation. This paper is a prelude to Part 2, which describes the determination of thermodynamic and kinetic properties of peroxy bleaches and discusses the implication of the results in terms of precautions for their safe storage and incorporation into detergent formulations during processing.

  13. BLEACHING EUCALYPTUS PULPS WITH SHORT SEQUENCES

    Flaviana Reis Milagres; Jorge Luiz Colodette; Marcos Sousa Rabelo; Danila Morais de Carvalho

    2011-01-01

    Eucalyptus spp kraft pulp, due to its high content of hexenuronic acids, is quite easy to bleach. Therefore, investigations have been made attempting to decrease the number of stages in the bleaching process in order to minimize capital costs. This study focused on the evaluation of short ECF (Elemental Chlorine Free) and TCF (Totally Chlorine Free) sequences for bleaching oxygen delignified Eucalyptus spp kraft pulp to 90% ISO brightness: PMoDP (Molybdenum catalyzed acid peroxide, chlorine d...

  14. Influence of H2SO4 as Activator to ClO2 on the Bleaching Effects

    Xingxiang Ji; Jiachuan Chen; Guihua Yang,; Zhong Jian Tian

    2012-01-01

    In this study, we show that chlorine dioxide activated by 4% Hydrochloric Acid Solution (HCl) has the same bleaching effects as that by sulfuric acid (H2SO4). Chlorine dioxide is an important bleaching agent in ECF bleaching. Stable chlorine dioxide in conjunction with Hydrochloric Acid Solution (HCl) activation in a certain proportion can be applied in the process of pulp bleach with a bleaching result of environment friendly, positive brightness stability, low pollutant bleach and pulp brig...

  15. Docosahexaenoic acid affects arachidonic acid uptake in megakaryocytes

    Schick, P.K.; Webster, P.

    1987-05-01

    Dietary omega 3 fatty acids are thought to prevent atherosclerosis, possibly by modifying platelet (PT) function and arachidonic acid (20:4) metabolism. The study was designed to determine whether omega 3 fatty acids primarily affect 20:4 metabolism in megakaryocytes (MK), bone marrow precursors of PT, rather than in circulating PT. MK and PT were isolated from guinea pigs and incubated with (/sup 14/C)-20:4 (0.13uM). Docosahexaenoic acid (22:6) is a major omega 3 fatty acid in marine oils. The incubation of MK with 22:6 (0.1, 1.0 uM) resulted in the decrease of incorporation of (/sup 14/C)-20:4 into total MK phospholipids, 16% and 41% respectively. Alpha-linolenic acid (18:3), a major omega 3 fatty acid present in American diets, had no effect on 20:4 uptake in MK. 22:6 primarily affected the uptake of (/sup 14/C)-20:4 into phosphatidylethanolamine (PE) and phosphatidylserine (PS) in MK. In MK, 22:6 (0.1, 1.0 uM) caused a decrease of incorporation of (/sup 14/C)-20:4 into PE, 21% and 55% respectively; a decrease into PS, 16% and 48% respectively; but only a decrease of 4% and 18%, respectively, into phosphatidylcholine; and a decrease of 3% and 21% into phosphatidylinositol 22:6 (3.0 uM) had no effect on the uptake of AA into PT phospholipids. The study shows that 22:6 has a selective effect on AA uptake in MK and that the acylation or transacylation of PE and PS are primarily affected. 22:6 and other marine omega 3 fatty acids appear to primarily affect megakaryocytes which may result in the production of platelets with abnormal content and compartmentalization of AA.

  16. OZONE BLEACHING AT NEUTRAL PH – A NEW CONCEPT

    Fernando de Carvalho

    2010-08-01

    Full Text Available The effect of medium consistency ozone stage pH was evaluated for brown and oxygen delignified eucalyptus kraft pulp samples obtained from VCP - Luiz Antônio pulp mill. These samples were used as such or previously treated with the hot acid stage (A. The main objective of this study was to determine the viability of increasing the ozone stage pH aiming at decreasing bleaching variable costs. The ozone stage was studied in the pH range of 2.5-9.0, taking into account some important variables which affect ozone bleaching: (1 pulp kappa number entering the ozone stage, (2 reactivity of ozone towards lignin versus hexenuronic acids (HexA´s, (3 pulp treatments prior to ozone stage (acid hydrolysis, and (4 pulp treatments after the ozone stage (extraction or a chlorine dioxide stage.  Therefore, the impact of ozone stage pH was investigated in bleaching process such as Z/DEop vs AZ/DEop, Z/DEopD vs AZ/DEopD, Z/E vs AZ/E. The results were interpreted based on ozone stage efficiency and selectivity, and overall bleaching performance measured by the total bleaching chemical consumption required to achieve full brightness, pulp quality and environmental impact. It was concluded that the increase of ozone stage pH from 2.5 to 7.0 has a slightly negative impact on the efficiency and selectivity, measured after Z/DEop sequence, but this effect is not expressive in the end of Z/DEopD bleaching sequence. The increase of ozone stage pH from 2.5 to 7.0 in the sequence Z/DEopD is cost-effective at industrial level because it represents expressive reduction of sulphuric acid and caustic soda demand for pH control in the bleaching plant. These gain areas achieved without any significant changes in pulp quality and effluent load discharge. Nevertheless, the increase of ozone stage pH from 2.5 to 7.0 has a very high negative impact on the efficiency and selectivity for the Z/E and AZ/E processes and it is not recommended in such cases.

  17. Esthetic rehabilitation with tooth bleaching, enamel microabrasion, and direct adhesive restorations.

    Bezerra-Júnior, Douglas Machado; Silva, Luciana Mendonça; Martins, Leandro de Moura; Cohen-Carneiro, Flávia; Pontes, Danielson Guedes

    2016-01-01

    The aim of this case report is to report esthetic rehabilitation with combined tooth bleaching, enamel microabrasion, and anterior restoration replacement in a 26-year-old man. Clinical examination showed deficient restorations in the maxillary anterior teeth, significant discoloration of the maxillary left central incisor, and hypoplastic stains affecting the maxillary right lateral incisor. A radiograph of the left central incisor showed satisfactory endodontic treatment, allowing preparation for the walking bleach technique. For 3 weeks, 37% carbamide peroxide in the pulp chamber was renewed every week. In-office bleaching with 35% hydrogen peroxide was also performed on the maxillary teeth. After 21 days, all teeth had been bleached to shade A1. After bleaching was completed, enamel microabrasion of the maxillary right lateral incisor was conducted with 6% hydrochloric acid. In later sessions, microhybrid composite resin restorations were placed in all 4 maxillary incisors. A combination of dental bleaching techniques, enamel microabrasion, and resin restorations was a successful and conservative choice for reestablishing the natural appearance of discolored teeth, improving the self-esteem of the patient. PMID:26943091

  18. A utilização de perácidos na deslignificação e no branqueamento de polpas celulósicas The use of peracids in delignification and cellulose pulp bleaching

    Lilian Borges Brasileiro

    2001-12-01

    Full Text Available Peracids are strong oxidant species and their use is being largely studied in the delignification and cellulose pulp bleaching. Some of them has already an industrial application, specially in non-conventional bleaching sequences like ECF (Elemental chlorine free and TCF (Totally chlorine free. This review presents the main aspects of the structure, properties, preparation and reaction of peracids (peracetic acid, peroxymonosulfuric acid and their mixture with lignin, specially for peracetic acid. Information about bleaching and delignification of wood pulps with peracids and the factors affecting its efficiency are also presented.

  19. Study of Melanin Bleaching After Immunohistochemistry of Melanin-containing Tissues

    Shen, Hongwu; Wu, Wenqiao

    2015-01-01

    Melanin may interfere with immunohistochemical staining. The goal of this study was to investigate the effects of trichloroisocyanuric acid (TCCA) bleaching, potassium permanganate bleaching, and potassium dichromate bleaching on melanin, tissue antigen, and 3,3′-diaminobenzidine (DAB) using melanin-containing and melanin-free tissue samples. Our results demonstrated that all 3 bleaching methods efficiently bleached melanin and partially destroyed tissue antigen. In addition, potassium perman...

  20. Evaluation of peanut hulls as an alternative to bleaching clays

    Hassanein, M. M.M.; El- Shami, S. M.; Taha, F. S.

    2011-01-01

    Peanut hulls (PNH) were carbonized at different temperatures, times, and evaluated at different concentrations as an alternative to bleaching clays. Evaluation of bleached crude soybean oil with PNH was based on their delta free fatty acids, reduction in peroxide value (PV), reduction in phospholipids (PL) and bleachability. The performance of several commercially used bleaching clays was evaluated, for comparison. Mixtures were formulated including: PNH and Tonsil -N (TN), PNH and Fuller’s e...

  1. EFFECT OF BIRCH KRAFT PULP PRIMARY FINES ON BLEACHING AND SHEET PROPERTIES

    Sari Anneli Asikainen

    2010-08-01

    Full Text Available By removing the primary fines from an oxygen-delignified mill birch pulp, a fiber fraction was obtained having low metals content and no extractives. After DEDeD bleaching the fiber fraction had somewhat higher brightness and better brightness stability than the birch pulp containing the primary fines. The fines fraction was enriched with lignin, extractives, xylan, and metals. Bleaching the fines fraction in a QQP sequence did not affect the extractives, whereas a ZeQP sequence clearly reduced the extractives content. In a biorefinery concept, the fines fraction could be utilized as a source of xylan, fatty acids, sterols, and betulinol. Another possibility is to use the fines fraction unbleached or separately bleached as a bonding material in various fiber furnishes.

  2. Use of Carbonized Seed Hulls as Alternative to Bleaching Clay During Miscella Bleaching of Oils

    Mona El- Hamidi; Taha, F. S.; Safinaz M. El- Shami; Hassanein, Minar M. M.

    2016-01-01

    Soybean oil (SBO) was miscella bleached in hexane using carbonized hulls of Jojoba (Jo), Jatrova (Ja), Peanuts (PN) and Pistachios (P) as alternatives to bleaching clays. Evaluation of bleached crude SBO with carbonized hulls was based on their delta-Free Fatty Acids (ΔFFA), reduction in Peroxide Value (PV), carotenoid content, color index and bleachability. Fuller’s Earth (FE) and Tonsil N (TN) were used for comparison with the carbonized hulls. Three oil: hexane ratios, 1: 0.5, 1:1 and 1:1....

  3. Layer-by-layer hyaluronic acid/chitosan polyelectrolyte coated mesoporous silica nanoparticles as pH-responsive nanocontainers for optical bleaching of cellulose fabrics.

    Yilmaz, M Deniz

    2016-08-01

    Polyelectrolyte multilayer (PEM) films composed of two natural polysaccharides (hyaluronic acid and chitosan) were deposited through layer-by-layer (LbL) assembly on top of biocompatible mesoporous silica nanoparticles (MSNPs). Polyelectrolyte multilayer coated mesoporous silica nanoparticles (PEM-MSNPs) were characterized by using attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), nitrogen adsorption-desorption isotherms, UV-vis and fluorescence spectrophotometer. A commercially available and industrially used optical brightener, 4,4'-distyrylbiphenyl sulfonate sodium salt (CBSX) was loaded into nanocontainers (CBSX@PEM-MSNPs) to evaluate their use for the pH-sensitive release. The controlled release of CBSX from nanocontainers in response to pH is monitored by using UV-vis and fluorescence spectrophotometer in water and the almost 100% of encapsulated CBSX is released within 2h at pH 7. The increase in both whiteness and total color change at pH 7 on a cellulose fabric demonstrates the great potential of nanocontainers as pH-sensitive whitening agents for optical bleaching of cellulose fabrics. PMID:27112863

  4. Adsorption and photocatalytic and photosensitised bleaching of acid orange 7 on multilayer mesoporous films of TiO2

    Mills, A.; O´Rourke, Ch.; Kalousek, Vít; Rathouský, Jiří

    2012-01-01

    Roč. 211, SI (2012), s. 182-187. ISSN 0304-3894 Institutional support: RVO:61388955 Keywords : acid orange 7 * photocatalysis * titania Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.925, year: 2012

  5. Thermoluminescence emission spectra and optical bleaching of oligoclase

    Thermoluminescence (TL) spectra of oligoclase samples have been recorded in the temperature range from 300 to 700 K and the wavelength range from 300 to 850 nm. Like other feldspars, oligoclase produces blue (peaking at 460 nm) and red (peaking at 765 nm) emission bands. The maximum of the red emission occurs 20 K lower than that of the blue band. Optical bleaching was performed at wavelengths varying from 360 to 800 nm. Bleaching of artificially irradiated oligoclase causes a decrease of the TL signal. The bleaching efficiency increases with decreasing wavelength. Bleaching does not only influence the height of the glow curve but also the shape. An interesting observation is that the ratio of the blue and red band intensities is not affected by a bleaching procedure. No evidence has been found that bleaching influences the shape of the emission spectra. The correlation between the blue and red bands is discussed. (Author)

  6. Kraft pulp bleaching with molybdenum activated acid peroxide (P{sub Mo} stage); Branqueamento de polpa celulosica kraft de eucalipto com peroxido acido ativado por molibdenio

    Rabelo, Marcos Sousa [Servico Nacional de Aprendizagem Industrial (SENAI), Lauro de Freitas, BA (Brazil). Dept. Regional da Bahia; Silva, Vanessa Lopes; Barros, Denise Pires de; Colodette, Jorge Luiz [Universidade Federal de Vicosa (UFV), MG (Brazil). Dept. de Engenharia Florestal; Sacon, Vera Maria; Silva, Marcelo Rodrigues da [Votorantim Celulose e Papel, Jacarei, SP (Brazil)

    2009-07-01

    Optimum conditions to run the P{sub Mo} stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H{sub 2}O{sub 2}. The P{sub Mo} stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P{sub Mo} stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

  7. Factors Affecting the Relative Efficiency of General Acid Catalysis

    Kwan, Eugene E.

    2005-01-01

    A simple framework for evaluating experimental kinetic data to provide support for Specific Acid Catalysis (SAC) and General Acid Catalysis (GAC) is described based on the factors affecting their relative efficiency. Observations reveal that increasing the SAC-to-GAC rate constant ratio reduces the effective pH range for GAC.

  8. Patterns of coral bleaching: Modeling the adaptive bleaching hypothesis

    Ware, J.R.; Fautin, D.G.; Buddemeier, R.W.

    1996-01-01

    Bleaching - the loss of symbiotic dinoflagellates (zooxanthellae) from animals normally possessing them - can be induced by a variety of stresses, of which temperature has received the most attention. Bleaching is generally considered detrimental, but Buddemeier and Fautin have proposed that bleaching is also adaptive, providing an opportunity for recombining hosts with alternative algal types to form symbioses that might be better adapted to altered circumstances. Our mathematical model of this "adaptive bleaching hypothesis" provides insight into how animal-algae symbioses might react under various circumstances. It emulates many aspects of the coral bleaching phenomenon including: corals bleaching in response to a temperature only slightly greater than their average local maximum temperature; background bleaching; bleaching events being followed by bleaching of lesser magnitude in the subsequent one to several years; higher thermal tolerance of corals subject to environmental variability compared with those living under more constant conditions; patchiness in bleaching; and bleaching at temperatures that had not previously resulted in bleaching. ?? 1996 Elsevier Science B.V. All rights reserved.

  9. Ocean Acidification: A Major Driver of Coral Bleaching in the 21st Century?

    Anthony, K.; Eakin, M. C.; Cao, L.; Caldeira, K.; Hoegh-Guldberg, O.

    2009-05-01

    Heat stress long been known to drive patterns of coral bleaching. Recently, however, it was discovered that ocean acidification can drive coral bleaching independently of temperature. This raises the question: how important will acidification be in driving coral bleaching under climate change? Here, we develop and apply a model that accounts for both thermal stress and ocean acidification in the coral bleaching response. Our analyses, which combine experimental bleaching data under manipulated ocean chemistry and warming with projections of CO2 and SST based on global circulation models, show that ocean acidification will become a key driver of future mass bleaching events within a few decades. Our findings, based on highly conservative assumptions, reveal that coral bleaching alert systems based on warming alone could underestimate coral bleaching by up to 50% during the 21st century. This is a striking result that will affect coral reef management strategies worldwide and has policy implications relating to global efforts to reduce greenhouse gas emissions.

  10. Bleached dissolving pulps applying laccase treatments

    Quintana, Elisabet; Valls Vidal, Cristina; Roncero Vivero, María Blanca

    2012-01-01

    A biobleaching sequence, using a laccase enzyme (Trametes Villosa) in combination with different mediators, was applied to softwood dissolving cellulose in order to study its bleaching efficiency and its potential in terms of kappa number, ISO brightness and viscosity. The tested mediators were classified as synthetic compounds such as HBT (1-hydroxybenzotriazole) and VA (violuric acid), and as natural compounds such as SA (syringaldehyde) and pCA (p-coumaric acid). The influence of the enzym...

  11. Bleach Neutralizes Mold Allergens

    Science Teacher, 2005

    2005-01-01

    Researchers at National Jewish Medical and Research Center have demonstrated that dilute bleach not only kills common household mold, but may also neutralize the mold allergens that cause most mold-related health complaints. The study, published in the Journal of Allergy and Clinical Immunology, is the first to test the effect on allergic…

  12. Enzymes improve ECF bleaching of pulp

    Lachenal, D.

    2006-07-01

    Full Text Available The delignification efficiency of different laccase enzymes was examined on the eucalyptus Kraft pulp. The laccase enzyme from Trametes versicolor showing the highest delignification efficiency was selected and used in the elemental chlorine-free bleaching sequence for improving the pulp bleachability. An appreciable reduction in chlorine dioxide consumption was also obtained. Further reduction in chlorine dioxide consumption was obtained when the same laccase treated pulp was subjected to an acid treatment after the extraction stage followed by the DEPD sequence. Elemental-chlorine free bleaching was also performed using the xylanase-laccase treated pulp. Xylanase treatment was incorporated to the laccase mediator system in the elemental-chlorine free bleaching both sequentially and simultaneously. The bleaching sequence DEPD followed and in both the cases, the reduction in chlorine dioxide consumption was greater in comparison to the control. The chlorine dioxide consumption was reduced further when xylanase-laccase treated pulp was given an additional acid treatment. The final pulp properties of the treated pulps were comparable to the control pulp.

  13. BLEACHING NEPTUNE BALLS

    BONET Maria Angeles

    2014-05-01

    Full Text Available Posidonia Oceanic is a seaweed from Mediterranean Sea and it is more concentrated at the Balerian SEA. This implies the Valencian Community also. It forms vaste underwater meadows in the sea and are part of the Mediterranean ecosystem. It is a sea-grass specie with fruits and flowers. Leaves are ribbon-like and they grow in winter and at the end of summer some of them are separated and arrive to some sea line. Fuit is separated and can floate, it is known as “the olive of the sea” mainly in Italy, or as the Neptune Balls. As it can be used in different fields, it is is being studied in order ro have the precitice tests. Some authors have reported the manufacturing of fully bio-based comites with a gluten matrix by hot-press molding. And it has been considered as an effective insulator for building industry or even though to determine the presence of mercure in the Mediterranean sea some years ago. As many applications can be designed from that fibers, it has been considered to be bleached in order to used them in fashionable products. Consequently, its original brown color is not the most suitable one and it should be bleached as many other cellulosic fibers. The aim of this paper is to bleache neptune balls however, the inner fibers were not accessible at all and it implied not to bleach the inner fibers in the neptune ball. Further studiesd will consider bleaching the individualized fibers.

  14. Influence of H2SO4 as Activator to ClO2 on the Bleaching Effects

    Xingxiang Ji

    2012-08-01

    Full Text Available In this study, we show that chlorine dioxide activated by 4% Hydrochloric Acid Solution (HCl has the same bleaching effects as that by sulfuric acid (H2SO4. Chlorine dioxide is an important bleaching agent in ECF bleaching. Stable chlorine dioxide in conjunction with Hydrochloric Acid Solution (HCl activation in a certain proportion can be applied in the process of pulp bleach with a bleaching result of environment friendly, positive brightness stability, low pollutant bleach and pulp brightness stability, not easy to reverse. By experiment of OD, ODED, ODQP bleach Triploid of Populus Tomentos with stable chlorine dioxide activated by sulfuric acid (H2SO4. Moreover, the result of the experiment can prove that principle of activation of HCl to ClO2 is similar to H2SO4 to ClO2, that is, to provide an acid environment for ClO2.

  15. Effect of bleaching on the microhardness of tooth-colored restorative materials

    Abdolrahim Davari

    2013-08-01

    Full Text Available   Background and Aims: Bleaching agents not only affect the tooth structure, but also may alter the properties of restorative materials. The aim of this in vitro study was to evaluate the effect of different bleaching regimens on the microhardness of four tooth-colored restorative materials.   Materials and Methods: Eighty specimens of four restorative materials (Microhybrid resin composite (Z250 (3M, ESPE, nanohybrid composite Z350 (3M, ESPE, packable composite P60 (3M, ESPE, and resin modified glass ionomer Vitremer (3M, ESPE were fabricated and were polished after 24 h with Soflex discs (3M,ESPE. Then the specimens were divided into two groups: In office bleach group, 40 specimens (10 of each restorative material were bleached with hydrogen peroxide 37.5% for 30 min in two sessions with 7 days interval. In home bleaching group, 40 specimens were bleached with carbamid peroxide 22%, 6 h a day for 14 days. Vickers microhardness test were done before and after bleaching (baseline. Finally data were evaluated using analysis of Variance.   Results: Two bleaching regimens were significantly decreased the microhardness values. In Z250 resin composite, the microhardness values before and after bleaching were 95.30 and 92.67 kg/mm2, respectively. for office bleaching (P=0.011 and 95.38 and 92.39 kg/mm2 for home bleaching (P<0.001. In Z350 resin composite, the microhardness values before and after bleaching were 98.29 and 92.41 kg/mm2, for office bleaching (P<0.001 and 97.35 and 93.44 kg/mm2 for home bleaching (P<0.001 respectively. In P60 resin composite, the microhardness values before and after bleaching were 103.10 and 96.16 kg/mm2, respectively. for office bleaching (P=0.045 and 102.61 and 98.16 kg/mm2 for home bleaching (P=0.001. In resin modified glass ionomer (Vitremer, the microhardness values before and after bleaching were 56.79 and 49.41 kg/mm2, respectively. for office bleaching (P=0.004 and 54.17 and 46.50 kg/mm2 for home bleaching (P

  16. Coral bleaching response index: a new tool to standardize and compare susceptibility to thermal bleaching.

    Swain, Timothy D; Vega-Perkins, Jesse B; Oestreich, William K; Triebold, Conrad; DuBois, Emily; Henss, Jillian; Baird, Andrew; Siple, Margaret; Backman, Vadim; Marcelino, Luisa

    2016-07-01

    As coral bleaching events become more frequent and intense, our ability to predict and mitigate future events depends upon our capacity to interpret patterns within previous episodes. Responses to thermal stress vary among coral species; however the diversity of coral assemblages, environmental conditions, assessment protocols, and severity criteria applied in the global effort to document bleaching patterns creates challenges for the development of a systemic metric of taxon-specific response. Here, we describe and validate a novel framework to standardize bleaching response records and estimate their measurement uncertainties. Taxon-specific bleaching and mortality records (2036) of 374 coral taxa (during 1982-2006) at 316 sites were standardized to average percent tissue area affected and a taxon-specific bleaching response index (taxon-BRI) was calculated by averaging taxon-specific response over all sites where a taxon was present. Differential bleaching among corals was widely variable (mean taxon-BRI = 25.06 ± 18.44%, ±SE). Coral response may differ because holobionts are biologically different (intrinsic factors), they were exposed to different environmental conditions (extrinsic factors), or inconsistencies in reporting (measurement uncertainty). We found that both extrinsic and intrinsic factors have comparable influence within a given site and event (60% and 40% of bleaching response variance of all records explained, respectively). However, when responses of individual taxa are averaged across sites to obtain taxon-BRI, differential response was primarily driven by intrinsic differences among taxa (65% of taxon-BRI variance explained), not conditions across sites (6% explained), nor measurement uncertainty (29% explained). Thus, taxon-BRI is a robust metric of intrinsic susceptibility of coral taxa. Taxon-BRI provides a broadly applicable framework for standardization and error estimation for disparate historical records and collection of novel

  17. Reef fishes can recognize bleached habitat during settlement: sea anemone bleaching alters anemonefish host selection.

    Scott, Anna; Dixson, Danielle L

    2016-05-25

    Understanding how bleaching impacts the settlement of symbiotic habitat specialists and whether there is flexibility in settlement choices with regard to habitat quality is essential given our changing climate. We used five anemonefishes (Amphiprion clarkii, Amphiprion latezonatus, Amphiprion ocellaris, Amphiprion percula and Premnas biaculeatus) and three host sea anemones (Entacmaea quadricolor, Heteractis crispa and Heteractis magnifica) in paired-choice flume experiments to determine whether habitat naive juveniles have the olfactory capabilities to distinguish between unbleached and bleached hosts, and how this may affect settlement decisions. All anemonefishes were able to distinguish between bleached and unbleached hosts, and responded only to chemical cues from species-specific host anemones irrespective of health status, indicating a lack of flexibility in host use. While bleached hosts were selected as habitat, this occurred only when unbleached options were unavailable, with the exception of A. latezonatus, which showed strong preferences for H. crispa regardless of health. This study highlights the potential deleterious indirect impacts of declining habitat quality during larval settlement in habitat specialists, which could be important in the field, given that bleaching events are becoming increasingly common. PMID:27226472

  18. Mill Designed Bio bleaching Technologies

    Institute of Paper Science Technology

    2004-01-30

    A key finding of this research program was that Laccase Mediator Systems (LMS) treatments on high-kappa kraft could be successfully accomplished providing substantial delignification (i.e., > 50%) without detrimental impact on viscosity and significantly improved yield properties. The efficiency of the LMS was evident since most of the lignin from the pulp was removed in less than one hour at 45 degrees C. Of the mediators investigated, violuric acid was the most effective vis-a-vis delignification. A comparative study between oxygen delignification and violuric acid revealed that under relatively mild conditions, a single or a double LMS{sub VA} treatment is comparable to a single or a double O stage. Of great notability was the retention of end viscosity of LMS{sub VA} treated pulps with respect to the end viscosity of oxygen treated pulps. These pulps could then be bleached to full brightness values employing conventional ECF bleaching technologies and the final pulp physical properties were equal and/or better than those bleached in a conventional ECF manner employing an aggressively O or OO stage initially. Spectral analyses of residual lignins isolated after LMS treated high-kappa kraft pulps revealed that similar to HBT, VA and NHA preferentially attack phenolic lignin moieties. In addition, a substantial decrease in aliphatic hydroxyl groups was also noted, suggesting side chain oxidation. In all cases, an increase in carboxylic acid was observed. Of notable importance was the different selectivity of NHA, VA and HBT towards lignin functional groups, despite the common N-OH moiety. C-5 condensed phenolic lignin groups were overall resistant to an LMS{sub NHA, HBT} treatments but to a lesser extent to an LMS{sub VA}. The inactiveness of these condensed lignin moieties was not observed when low-kappa kraft pulps were biobleached, suggesting that the LMS chemistry is influenced by the extent of delignification. We have also demonstrated that the current

  19. Evaluation of peanut hulls as an alternative to bleaching clays

    Hassanein, M. M.; El-Shami, S. M.; Taha, F. S.

    2011-07-01

    Peanut hulls (PNH) were carbonized at different temperatures, times, and evaluated at different concentrations as an alternative to bleaching clays. Evaluation of bleached crude soybean oil with PNH was based on their delta free fatty acids, reduction in peroxide value (PV), reduction in phospholipids (PL) and bleachability. The performance of several commercially used bleaching clays was evaluated, for comparison. Mixtures were formulated including: PNH and Tonsil -N (TN), PNH and Fuller's earth (FE) and PNH and O-passive (OP) and examined. The oxidative stability of oils was determined. Results for the investigated commercial bleaching clays revealed: TN > FE > F > TF > OP. Highest reduction in PV and PL, and highest bleachability were achieved for soybean oil bleached with 2% PNH carbonized at 500 degree centigrade for 30 min (PNH). Mixtures of PNH with the three chosen bleaching clays indicated that 1PNH : 2TN gave the highest bleachability. CSO was miscella bleached in hexane using PNH and resulted in an appreciable improvement in all oil characteristics, especially in bleachability. Oxidative stability of oils was in the following order: TN > control > FE > PNH with Induction period values of 23.1 > 6.43 > 5.73 > 2.85 h, respectively. (Author) 20 refs.

  20. STUDY ON THE EFFECTS OF ACID ETCHING ON AFFECTED ENAMEL

    Simona Stoleriu

    2011-12-01

    Full Text Available The purpose of the study was to establish and compare the effects of ortophosphoric and hydrochloric acids on the enamel affected by incipient carious lesions with different evolution. Materials and method. 20 teeth with acute and chronic non-cavitary carious lesions were considered for the study. The teeth were sectioned in two halves through the middle of the non-cavitary lesions. The halves of 5 white spot-type lesions and of 5 brown spot-type ones were analyzed as to their surface roughness, on an atomic force microscope (AFM. 5 halves with white spot-type lesions and 5 halves with brown spot-type ones were subjected to acid etching with 37% ortophosphoric acid (Scotchbond etchant gel, 3M ESPE, and an equal number of samples was subjected to the action of 15% hydrochloric acid (ICON-etch, DMG Dental Products Ltd for 2 min, then washed with water and analyzed by AFM. Results. The initial surface roughness of the enamel was higher in the white spot–type carious lesions, comparatively with the brown spot-type ones. For both types of carious non-cavitary lesions, acid etching with phosphoric and hydrochloric acid significantly increased the surface roughness of the enamel, comparatively with the status of the enamel surface prior to etching. The hydrochloric acid led to a surface roughness significantly higher than in the case of ortophosphoric acid, in both acute and chronic non-cavitary carious lesions. The roughness values obtained through etching with ortophosphoric and hydrochloric acid were higher in the white spot-type carious lesions, comparatively with the brown spot-type ones. Conclusions. Both the 37% ortophosphoric acid and the 15% hydrochloric acid determined a significantly higher surface roughness of the enamel affected by acute and chronic non-cavitary carious lesions. The surface condition of the brown spot-type carious lesions was less significantly modified, comparatively with that of the white spot-type lesions, by the

  1. Augmenting acid with affective details to assess credibility

    Roland Fleck

    2011-07-01

    Full Text Available There is a need within the criminal justice systems of many countries to create a valid and applicable system of investigative interviewing and credibility assessment. The present study assesses the general validity one such system, called Assessment Criteria Indicative of Deception (ACID. ACID comprises interviewing strategies that facilitate the detection of deception and content criteria that highlight differences in verbal behavior. Sixty university undergraduates performed a staged theft under time pressure and with incentives designed to increase external validity. The participants were interviewed and assessed using the ACID procedure. Half of them were instructed to answer honestly and the other half to deny his/her participation in the theft. Results showed that honest statements were longer, more vividly detailed, and more spontaneously structured than deceptive statements. Also, the addition of affective details as a dependent measure significantly improved the ACID system. Overall, 48 of 60 statements were accurately classified (26 of 30 honest statements and 22 of 30 deceptive statements. The ACID procedure was effective and benefited from the addition of affective details. The strengths and weaknesses of this study are discussed in light of basic research into deception and potential forensic application.

  2. Mineral loss and color change of enamel after bleaching and staining solutions combination.

    de Araújo, Larissa Sgarbosa Napoleão; dos Santos, Paulo Henrique; Anchieta, Rodolfo Bruniera; Catelan, Anderson; Fraga Briso, André Luiz; Fraga Zaze, Ana Carolina Soares; Sundfeld, Renato Herman

    2013-10-01

    Pigments of food and beverages could affect dental bleaching efficacy. The aim of this investigation was to evaluate color change and mineral loss of tooth enamel as well as the influence of staining solutions normally used by adolescent patients undergoing home bleaching. Initial hardness and baseline color were measured on enamel blocks. Specimens were divided into five groups (n=5): G1 (control) specimens were kept in artificial saliva throughout the experiment (3 weeks); G2 enamel was exposed to 10% carbamide peroxide for 6 h daily, and after this period, the teeth were cleaned and stored in artificial saliva until the next bleaching session; and G3, G4, and G5 received the same treatments as G2, but after bleaching, they were stored for 1 h in cola soft drink, melted chocolate, or red wine, respectively. Mineral loss was obtained by the percentage of hardness reduction, and color change was determined by the difference between the data obtained before and after treatments. Data were subjected to analysis of variance and Fisher's test (α=0.05). G3 and G5 showed higher mineral loss (92.96 ± 5.50 and 94.46 ± 1.00, respectively) compared to the other groups (p ≤ 0.05). G5 showed high-color change (9.34 ± 2.90), whereas G1 presented lower color change (2.22 ± 0.44) (p ≤ 0.05). Acidic drinks cause mineral loss of the enamel, which could modify the surface and reduce staining resistance after bleaching. PMID:24165745

  3. Biomass pretreatment affects Ustilago maydis in producing itaconic acid

    Klement Tobias

    2012-04-01

    Full Text Available Abstract Background In the last years, the biotechnological production of platform chemicals for fuel components has become a major focus of interest. Although ligno-cellulosic material is considered as suitable feedstock, the almost inevitable pretreatment of this recalcitrant material may interfere with the subsequent fermentation steps. In this study, the fungus Ustilago maydis was used to produce itaconic acid as platform chemical for the synthesis of potential biofuels such as 3-methyltetrahydrofuran. No studies, however, have investigated how pretreatment of ligno-cellulosic biomass precisely influences the subsequent fermentation by U. maydis. Thus, this current study aims to first characterize U. maydis in shake flasks and then to evaluate the influence of three exemplary pretreatment methods on the cultivation and itaconic acid production of this fungus. Cellulose enzymatically hydrolysed in seawater and salt-assisted organic-acid catalysed cellulose were investigated as substrates. Lastly, hydrolysed hemicellulose from fractionated beech wood was applied as substrate. Results U. maydis was characterized on shake flask level regarding its itaconic acid production on glucose. Nitrogen limitation was shown to be a crucial condition for the production of itaconic acid. For itaconic acid concentrations above 25 g/L, a significant product inhibition was observed. Performing experiments that simulated influences of possible pretreatment methods, U. maydis was only slightly affected by high osmolarities up to 3.5 osmol/L as well as of 0.1 M oxalic acid. The production of itaconic acid was achieved on pretreated cellulose in seawater and on the hydrolysed hemicellulosic fraction of pretreated beech wood. Conclusion The fungus U. maydis is a promising producer of itaconic acid, since it grows as single cells (yeast-like in submerged cultivations and it is extremely robust in high osmotic media and real seawater. Moreover, U. maydis can grow on

  4. ECF AND TCF BLEACHING OF SECONDARY FIBER PULP

    Gustavo Ventorim

    2009-09-01

    Full Text Available In this study, ECF and TCF bleaching processes were evaluated for the bleaching of a deinked mixed office waste (MOW pulp sample produced in a pilot plant. The sample was bleached by all processes to a target brightness of 78 % ISO minimum. The results were interpreted on the basis of chemical cost to reach the target brightness, bleaching yield and bleached pulp quality as measured by viscosity, fluorescence and b* color coordinate. Among the ECF sequences, the mosattractive was the DEDD which showed the lowest chemical cost and produced bleached pulp of high quality as measured by viscosity, fluorescence and b* coordinate. The best TCF sequence with ozone was the Q(PO(ZQ(PO which resulted in very high brightness ceiling. This sequence decreased moderately the pulp b* coordinate and viscosity and slightly its fluorescence. Among the TCF sequences without ozone the Q(POQ(PO was the most effective but showed poor flexibility with regard to brightness ceiling. This sequence had little effect on pulp viscosity, fluorescence and b* coordinate. For all three  bleaching processes, it was determined that process yield is negatively affected by hot alkaline stages such as O, P and (PO.

  5. Factors Affecting Sensitivity of Variable Charge Soils to Acid Rain

    WANGJING-HUA

    1995-01-01

    The sensitivity of a large number of variable charge soils to acid rain was evaluated through examining pH-H2SO4 input curves.Two derivative parameters,the consumption of hydrogen ions by the soil and the acidtolerant limit as defined as the quantity of sulfuric acid required to bring the soil to pH 3.5 in a 0.001mol L-1 Ca(NO3)2 solution,were used.The sensitivity of variable charge soils was higher than that of constant charge soils,due to the predominance of kaolinite in clay mineralogical composition.Among these soils the sensitivity was generally of the order lateritic red soil>red soil> latosol.For a given type of soil within the same region the sensitivity was affected by parent material,due to differences in clay minerals and texture.The sensitivity of surface soil may be lower or higher than that of subsiol,depending on whether organic matter or texture plays the dominant role in determining the buffering capacity.Paddy soils consumed more acid within lower range of acid input when compared with upland soils,due to the presence of more exchangeable bases,but consumed less acid within higher acid input range,caused by the decrease in clay content.

  6. RESPONSE SURFACE METHODOLOGY APPROACH FOR OPTIMIZATION OF FLAX SEED OIL BLEACHING PROCESS

    Miroslav Ondrejovič

    2013-10-01

    Full Text Available Flax seed is an important source of omega-3 polyunsaturated fatty acids essential for human physiology. For low oxidation stability, specific taste and concomitant color compounds this oil is poorly applicable as nutraceutical additive. The aim of this study was optimization of flax seed oil bleaching. The optimal conditions for the bleaching process were determined using response surface methodology. A central composite design was used to investigate the effects of three independent variables, namely solid to liquid ratio, temperature and time, to output parameters of the bleaching process such as crude oil color expressed as optical density at 490 nm, acid and peroxide value. Calculated optimal conditions for the bleaching, expressed by the optical density of the oil were as follows: temperature 50°C, bleaching time 77 minutes and solid-liquid ratio 56 g of bleaching agent to 1 liter of oil.

  7. Evaluation of bleach-sedimentation for sterilising and concentrating Mycobacterium tuberculosis in sputum specimens

    Valencia Teresa

    2011-10-01

    Full Text Available Abstract Background Bleach-sedimentation may improve microscopy for diagnosing tuberculosis by sterilising sputum and concentrating Mycobacterium tuberculosis. We studied gravity bleach-sedimentation effects on safety, sensitivity, speed and reliability of smear-microscopy. Methods This blinded, controlled study used sputum specimens (n = 72 from tuberculosis patients. Bleach concentrations and exposure times required to sterilise sputum (n = 31 were determined. In the light of these results, the performance of 5 gravity bleach-sedimentation techniques that sterilise sputum specimens (n = 16 were compared. The best-performing of these bleach-sedimentation techniques involved adding 1 volume of 5% bleach to 1 volume of sputum, shaking for 10-minutes, diluting in 8 volumes distilled water and sedimenting overnight before microscopy. This technique was further evaluated by comparing numbers of visible acid-fast bacilli, slide-reading speed and reliability for triplicate smears before versus after bleach-sedimentation of sputum specimens (n = 25. Triplicate smears were made to increase precision and were stained using the Ziehl-Neelsen method. Results M. tuberculosis in sputum was successfully sterilised by adding equal volumes of 15% bleach for 1-minute, 6% for 5-minutes or 3% for 20-minutes. Bleach-sedimentation significantly decreased the number of acid-fast bacilli visualised compared with conventional smears (geometric mean of acid-fast bacilli per 100 microscopy fields 166, 95%CI 68-406, versus 346, 95%CI 139-862, respectively; p = 0.02. Bleach-sedimentation diluted paucibacillary specimens less than specimens with higher concentrations of visible acid-fast bacilli (p = 0.02. Smears made from bleach-sedimented sputum were read more rapidly than conventional smears (9.6 versus 11.2 minutes, respectively, p = 0.03. Counting conventional acid-fast bacilli had high reliability (inter-observer agreement, r = 0.991 that was significantly reduced (p

  8. HE EFFECT OF TRANSITION METAL IONS-IRON ON HYDROGEN PEROXIDE BLEACHING

    Yumeng Zhao; Shuhui Yang; Liang Sheng; Yonghao Ni

    2004-01-01

    Hydrogen peroxide bleaching has been extensively used in high-yield pulp bleaching. Unfortunately,hydrogen peroxide can be decomposed under alkaline condition, especially when transition metal ions exit. Experiments show that the valence of transition metal ion is also responsible for the decomposition of hydrogen peroxide.Iron ions are present in two oxidation states, Fe2+ and Fe3+. They are both catalytically active to hydrogen peroxide decomposition. Because Fe3+ is brown, it can affect the brightness of pulp directly, it can also combine with phenol, forming complexes which not only are stable structures and are difficult to be removed from pulp, but also significantly affect the brightness of pulp because of their color.Sodium silicate and magnesium sulfate, when used together, can greatly decrease hydrogen peroxide decomposition. The optimum dosage of sodium silicate is about 0.1% (on solution) for Fe2+ and 0.25% (on solution) for Fe3+. Adding chelants such as DTPA or EDTA with stabilizers simultaneously can obviously improve pulp brightness. For iron ions, the chelate effect of DTPA is better than that of EDTA.Under acidic conditions, sodium hyposulfite and cellulose can reduce Fe3+ to Fe2+ effectively, and pulp brightness is improved greatly. Adding sodium thiosulfate simultaneously with magnesium sulfate,sodium silicate, and DTPA to alkaline peroxide solution can result in higher brightness of pulp.pH is a key parameter during hydrogen peroxide bleaching, the optimum pH value should be 10.5-12.

  9. The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

    Kátia Maria Morais Eiras; Jorge Luiz Colodette; Vanessa Lopes Silva

    2009-01-01

    Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX) content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxi...

  10. Major hydrogeochemical processes in an Acid Mine Drainage affected estuary

    Highlights: • Mixing of acid riverine water with alkaline seawater was studied in an estuary. • Combination of data and geochemical tools allowed modeling the water mixing. • The main geochemical processes were identified and for the first time quantified. • Water chemistry is the result of mixing, dissolution-precipitation and sorption. • Main reactions: gypsum and calcite dissolution and Al and Fe solids precipitation. - Abstract: This study provides geochemical data with the aim of identifying and quantifying the main processes occurring in an Acid Mine Drainage (AMD) affected estuary. With that purpose, water samples of the Huelva estuary were collected during a tidal half-cycle and ion–ion plots and geochemical modeling were performed to obtain a general conceptual model. Modeling results indicated that the main processes responsible for the hydrochemical evolution of the waters are: (i) the mixing of acid fluvial water with alkaline ocean water; (ii) precipitation of Fe oxyhydroxysulfates (schwertmannite) and hydroxides (ferrihydrite); (iii) precipitation of Al hydroxysulfates (jurbanite) and hydroxides (amorphous Al(OH)3); (iv) dissolution of calcite; and (v) dissolution of gypsum. All these processes, thermodynamically feasible in the light of their calculated saturation states, were quantified by mass-balance calculations and validated by reaction-path calculations. In addition, sorption processes were deduced by the non-conservative behavior of some elements (e.g., Cu and Zn)

  11. Trace elementary concentration in enamel after dental bleaching using HI-ERDA

    Added, N. [GFAA, Depto de Fisica Nuclear, IFUSP, University of Sao Paulo, Travessa R da rua do Matao 187, Cidade Universitaria, Caixa Postal 66318, CEP 05508-970 Sao Paulo, SP (Brazil)]. E-mail: nemitala@dfn.if.usp.br; Rizzutto, M.A. [GFAA, Depto de Fisica Nuclear, IFUSP, University of Sao Paulo, Travessa R da rua do Matao 187, Cidade Universitaria, Caixa Postal 66318, CEP 05508-970 Sao Paulo, SP (Brazil); Curado, J.F. [GFAA, Depto de Fisica Nuclear, IFUSP, University of Sao Paulo, Travessa R da rua do Matao 187, Cidade Universitaria, Caixa Postal 66318, CEP 05508-970 Sao Paulo, SP (Brazil); Francci, C. [School of Dentistry, University of Sao Paulo (Brazil); Markarian, R. [School of Dentistry, University of Sao Paulo (Brazil); Mori, M. [School of Dentistry, University of Sao Paulo (Brazil)

    2006-08-15

    Changes of elementary concentrations in dental enamel after a bleaching treatment with different products, is presented, with special focus on the oxygen contribution. Concentrations for Ca, P, O and C and some other trace elements were obtained for enamel of bovine incisor teeth by HI-ERDA measurements using a {sup 35}Cl incident beam and an ionization chamber. Five groups of teeth with five samples each were treated with a different bleaching agents. Each tooth had its crown sectioned in two halves, one for bleaching test and one the other used as a control. Average values of C/Ca, O/Ca, F/Ca enrichment factors were found. The comparison between bleached and non-bleached halves indicates that bleaching treatment did not affect the mineral structure when low-concentration whitening systems were used. The almost constant oxygen concentration in enamel, suggests little changes due to whitening therapy.

  12. Trace elementary concentration in enamel after dental bleaching using HI-ERDA

    Changes of elementary concentrations in dental enamel after a bleaching treatment with different products, is presented, with special focus on the oxygen contribution. Concentrations for Ca, P, O and C and some other trace elements were obtained for enamel of bovine incisor teeth by HI-ERDA measurements using a 35Cl incident beam and an ionization chamber. Five groups of teeth with five samples each were treated with a different bleaching agents. Each tooth had its crown sectioned in two halves, one for bleaching test and one the other used as a control. Average values of C/Ca, O/Ca, F/Ca enrichment factors were found. The comparison between bleached and non-bleached halves indicates that bleaching treatment did not affect the mineral structure when low-concentration whitening systems were used. The almost constant oxygen concentration in enamel, suggests little changes due to whitening therapy

  13. Humidity testing of bleached holograms.

    Chenoweth, A J

    1971-04-01

    One of the proposed storage media for semipermanent optical stores is an array of bleached holograms fabricated on photographic plates. If a store utilizing this medium is to be operated in a field environment, the effect of humidity variation requires consideration. In this study holograms were made using either Burckhardt's potassium ferricyanide or Russo and Sottini's modified R-10 type bleach on Kodak 649F and Agfa 10E70 plates. Diffraction efficiency was measured as a function of relative humidity over the range 30-98%. For holograms fabricated and tested as described above it was found that relative humidity values above 75% caused a permanent loss in diffraction efficiency for potassium ferricyanide bleached plates; humidity above 90% produced a temporary loss in R-10 bleached plates. PMID:20094561

  14. Optical dating: insufficiently bleached sediments

    Although infrared-stimulated luminescence (IRSL) signals in feldspars can be bleached rapidly by sunlight, there could still be a small amount of IRSL signal remaining in sediment grains if they have experienced only relatively short sunlight exposure before deposition. This remaining signal results in a ''remnant dose'' stored in the grain and is important for young samples but negligible for old samples. Several methods have been introduced to detect insufficient bleaching, and some of them can provide information on the extent of the bleaching. Others can only distinguish between samples bleached for a very long time and for a short time. Empirical methods are introduced to evaluate the possible values of equivalent dose accumulated since the grains were deposited. These methods involve the analysis of the equivalent doses and the natural IRSL signals obtained using single-disc dose determination methods. (author)

  15. Post-bleaching application of an antioxidant on dentin bond strength of three dental adhesives

    Maryam Khoroushi

    2012-01-01

    Conclusions: The findings suggest that bond strength of resin to bleached dentin may be affected with the adhesive system. Reduced SBS to bleached dentin can be amended by the use of SA as an antioxidizing agent. However, the amount of reversed bond strength subsequent to applying antioxidant might be related to the kind of dental adhesive.

  16. Corals differential susceptibilities to bleaching along the Red Sea Coast, Egypt

    MONTASER ALY MAHMOUD AL-HAMMADY

    2011-07-01

    Full Text Available Ammar MSA, Obuid-Allah AH, Al-Hammady MAM. 2011. Corals differential susceptibilities to bleaching along the Red Sea Coast, Egypt. Nusantara Bioscience 3: 73-81. Coral bleaching was studied at four sites in four widely geographically separated areas. Three of these sites are subjected to different human activities and the fourth one is considered as a control site. Data were collected by using SCUBA diving equipments and the line transects method. A total of 3940 coral colonies, representing 62 species in 21genera and 10 families, were recorded on transects on the reefs of four studied sites.20.11% of all corals were affected by bleaching: 5.4% were moderately affected; 2.7% severely affected and 12.007% were dead. Overall, there were differences in the proportion of colonies affected by bleaching between the studied sites. Ras El-Behar, the site impacted by petroleum oil, has the maximum average proportion of moderately, severely bleached and dead colonies. While, the lowest average proportions of severely bleached colonies and dead colonies were found at Kalawy bay. Surprisingly, coral reef taxa at El-Hamraween harbor showed high resistance to bleaching probably because of having a new different clade of Symbiodinium which can withstand sea water temperature. Species with highest susceptibilities to bleaching in areas of oil pollution, increased sedimentation and heavy load of phosphate are Stylophora pistillata, Acropora granulosa and Montipora meandrina, respectively while species with lowest susceptibilities are Fungia fungites, Alveopora daedalea and Millepora dichotoma, respectively.

  17. Local bleaching thresholds established by remote sensing techniques vary among reefs with deviating bleaching patterns during the 2012 event in the Arabian/Persian Gulf

    Shuail, Dawood; Wiedenmann, Jörg; D'Angelo, Cecilia; Baird, Andrew H.; Pratchett, Morgan S.; Riegl, Bernhard; Burt, John A.; Petrov, Peter; Amos, Carl

    2016-01-01

    A severe bleaching event affected coral communities off the coast of Abu Dhabi, UAE in August/September, 2012. In Saadiyat and Ras Ghanada reefs ~ 40% of the corals showed signs of bleaching. In contrast, only 15% of the corals were affected on Delma reef. Bleaching threshold temperatures for these sites were established using remotely sensed sea surface temperature (SST) data recorded by MODIS-Aqua. The calculated threshold temperatures varied between locations (34.48 °C, 34.55 °C, 35.05 °C)...

  18. The corrosion of titanium and some other construction materials during hydrogen peroxide bleaching according to the field measurements

    In a Finnish pulp mill, the field measurements of different materials were performed in different stages of peroxide bleaching: P1 and P2. The field measurements were performed with three different sensors. The sensors were designed in co-operation with Valmet Automation Kajaani Oy. Each sensor measured the corrosion potential, the redox potential and the weight losses of three different materials. Simultaneously, the data of the most important parameters of bleaching, i.e. temperature, pH, peroxide flow rate and concentration, mass flow, consistency, residuals, flow rate and concentration of alkaline, were collected in the data logger by a dedicated program. The results proved that the corrosion of different materials (stainless steel S31654, nickel-based alloy N10276 and titanium Gr. 5) could be estimated with field experiments. The uniform corrosion of titanium occurred in a certain bleaching situation. The field measurements gave a good estimation of whether the material dissolved during process operation or process disorders. Our results clearly show that the mixing of the chemicals can be reliably estimated, and thus advantageous for a pulp mill. The materials studied withstood the bleaching significantly better if the chemicals were mixed directly with a pulp. Usually the chemicals are mixed with alkaline and then added to the pulp. The field measurements could also be applied in ozone and in the peracetic acid bleaching stage. The sensors can be utilized as tools during process monitoring or diagnostics. With the aid of monitoring it is possible to clarify how the different process operation models affect the corrosion of materials. (author)

  19. Effect of thickener agents on dental enamel microhardness submitted to at-home bleaching Efeito de agentes espessantes na microdureza do esmalte submetido ao clareamento dental caseiro

    José Augusto Rodrigues; Glauco Paulo Felício Oliveira; Cristiane Mariote Amaral

    2007-01-01

    Dental bleaching occurs due to an oxidation reaction between the bleaching agents and the macromolecules of pigments in the teeth. This reaction is unspecific and the peroxides can also affect the dental matrix causing mineral loss. On the other hand, recent studies have suggested that the thickener agent carbopol can also cause mineral loss. Thus, the objective of this study was to evaluate in vitro the effect of at-home dental bleaching on dental enamel microhardness after the use of bleach...

  20. Antioxidant therapy enhances pulpal healing in bleached teeth

    Lima, Adriano Fonseca; Marques, Marcelo Rocha; Soares, Diana Gabriela; Hebling, Josimeri; Marchi, Giselle Maria

    2016-01-01

    Objectives The purpose of this study was to evaluate the histopathological effects of an antioxidant therapy on the pulp tissue of rat teeth exposed to a bleaching gel with 35% hydrogen peroxide. Materials and Methods Forty rats were subjected to oral ingestion by gavage of distilled water (DW) or ascorbic acid (AA) 90 min before the bleaching therapy. For the bleaching treatment, the agent was applied twice for 5 min each to buccal surfaces of the first right mandibular molars. Then, the animals were sacrificed at 6 hr, 24 hr, 3 day, or 7 day post-bleaching, and the teeth were processed for microscopic evaluation of the pulp tissue. Results At 6 hr, the pulp tissue showed moderate inflammatory reactions in all teeth of both groups. In the DW and AA groups, 100% and 80% of teeth exhibited pulp tissue with significant necrosis and intense tissue disorganization, respectively. At 24 hr, the AA-treated group demonstrated a greater regenerative capability than the DW group, with less intense inflammatory reaction and new odontoblast layer formation in 60% of the teeth. For up to the 7 day period, the areas of pulpal necrosis were replaced by viable connective tissue, and the dentin was underlined by differentiated odontoblast-like cells in most teeth of both groups. Conclusions A slight reduction in initial pulpal damage during post-bleaching was promoted by AA therapy. However, the pulp tissue of AA-treated animals featured faster regenerative potential over time. PMID:26877990

  1. SUGARCANE BAGASSE PULPING AND BLEACHING: THERMAL AND CHEMICAL CHARACTERIZATION

    Paulo Henrique Fernandes Pereira

    2011-05-01

    Full Text Available Cellulose fibers were isolated from sugarcane bagasse in three stages. Initially sugarcane bagasse was subjected to a pre-treatment process with hydrolyzed acid to eliminate hemicellulose. Whole cellulosic fibers thus obtained were then subjected to a two-stage delignification process and finally to a bleaching process. The chemical structure of the resulting cellulose fibers was studied by Fourier Transform Infrared (FTIR spectroscopy. Scanning Electron Microscopy (SEM and X-ray diffraction (XRD were used to analyze the effects of hydrolysis, delignification, and bleaching on the structure of the fibers. Two different thermal analysis techniques were used to study the bleaching cellulose fibers. These techniques confirmed that cellulose fibers were isolated from sugarcane bagasse. A future goal is to use these fibers as reinforcement elements in composites, organic-inorganic hybrid, and membranes for nanofiltration.

  2. Nanotribological and Nanomechanical Properties Changes of Tooth After Bleaching and Remineralization in Wet Environment

    Yu, Dandan; Gao, Shanshan; Min, Jie; Zhang, Qianqian; Gao, Shuai; Yu, Haiyang

    2015-12-01

    Teeth bleaching cases had increased with people's desire for oral aesthetic; however, bleached teeth would still undertake chewing actions and remineralizing process in saliva. Nanotribological and nanomechanical properties are proper displays for dental performance of bleached teeth. The purpose of the research was to reveal the effect of bleaching and remineralization on the nanotribological and nanomechanical properties of teeth in wet environment. The specimens were divided into four groups according to the bleaching products used: 12 % hydrogen peroxide (HP) (12HP group); 15 % carbamide peroxide (CP) (15CP group); 35 % CP (35CP group); and artificial saliva (control group). The nanotribological and nanomechanical property changes of tooth enamel after bleaching and remineralization were evaluated respectively by nanoscratch and nanoindentation tests in wet environment, imitating the wet oral environment. The morphology changes were evaluated by statistical parametric mapping (SPM) and scanning electron microscopy (SEM). After bleaching, 12HP group and 15CP group showed increased scratch depth with more pile ups on the scratch edges, decreased nanohardness, and corroded surface appearance. While the 35CP group showed an increase in nanoscratch depth, no change in nanohardness and surface appearance was observed. The control group showed no change in these measurements. After remineralization, the three bleaching groups showed decreased nanoscratch depth and no change of nanohardness compared with the bleached teeth. And the control group showed no changes in nanotribological and nanomechanical properties. The nanotribological and nanomechanical properties of the 12HP group and 15CP group were affected by bleaching, but the nanotribological properties recovered partly and the nanomechanical properties got no change after 1 week of remineralization. As for the 35CP group, the nanotribological properties were influenced and the nanomechanical properties were not

  3. Effects of coral bleaching on the obligate coral-dwelling crab Trapezia cymodoce

    Stella, J. S.; Munday, P. L.; Jones, G. P.

    2011-09-01

    Corals are an essential and threatened habitat for a diverse range of reef-associated animals. Episodes of coral bleaching are predicted to increase in frequency and intensity over coming decades, yet the effects of coral-host bleaching on the associated animal communities remain poorly understood. The present study investigated the effects of host-colony bleaching on the obligate coral-dwelling crab, Trapezia cymodoce, during a natural bleaching event in the lagoon of Lizard Island, Australia. Branching corals, which harbour the highest diversity of coral associates, comprised 13% of live coral cover at the study site, with 83% affected by bleaching. Crabs on healthy and bleached colonies of Pocillopora damicornis were monitored over a 5-week period to determine whether coral bleaching affected crab density and movement patterns. All coral colonies initially contained one breeding pair of crabs. There was a significant decline in crab density on bleached corals after 5 weeks, with many corals losing one or both crabs, yet all healthy colonies retained a mating pair. Fecundity of crabs collected from bleached and healthy colonies of P. damicornis was also compared. The size of egg clutches of crabs collected from bleached hosts was 40% smaller than those from healthy hosts, indicating a significant reduction in fecundity. A laboratory experiment on movement patterns found that host-colony bleaching also prompted crabs to emigrate in search of more suitable colonies. Emigrant crabs engaged in aggressive interactions with occupants of healthy hosts, with larger crabs always usurping occupants of a smaller size. Decreased densities and clutch sizes, along with increased competitive interactions, could potentially result in a population decline of these important coral associates with cascading effects on coral health.

  4. Reuse of discarded deactivated bleaching earth in the bleaching of oils

    Girgis, Adel Y.

    2005-03-01

    Full Text Available Discarded bleaching earth was used after its reactivation for the bleaching of sunflower, soybean and corn oils. The efficiency of reactivated bleaching earth was compared to the efficiency of virgin activated bleaching earth. Acid reactivated earth (pH 2.5-3 had a slightly higher content in silicone than virgin activated or neutralized reactivated earths. The best results in the color of sunflower and corn oils were obtained when neutralized earth (pH 6–7 was used at 1 and 2 % levels. Acid reactivated earth used at 2 % achieved a higher reduction in soybean oil color than virgin earth (pH 3 at the same dosage. Both reactivated earths reduced peroxide value, iron, conjugated dienes and soap, while they increased acidity and conjugated trienes. Furthermore, these reactivated earths determined higher decrements in the oil induction period than virgin earth. Reactivated earth could be used for 5 cycles for the bleaching of soybean or corn oils and for more than 6 cycles for sunflower oil.Tierra decolorante desechada, fue empleada, tras su reactivación para decolorar aceites de girasol, soja y maíz. La eficiencia de la tierra decolorante reactivada fue comparada con la de la virgen activada. La tierra reactivada ácida (pH 2,5–3 tuvo ligeramente mayor contenido en silicona que la tierra virgen o la reactivada neutra. Los mejores resultados en el color de los aceites de girasol y maíz fueron obtenidos cuando se emplearon niveles del 1 y 2 % de tierra reactivada neutra (pH 6-7. La tierra ácida reactivada, usada al 2 % consiguió una mayor reducción del color del aceite de soja, que una misma dosis de tierra virgen (pH 3. Ambas tierras reactivadas redujeron el índice de peróxidos, hierro, dienos conjugados y jabón de los aceites, mientras que hicieron aumentar la acidez y los trienos conjugados. Además, estas tierras reactivadas determinaron mayores descensos en los periodos de inducción del aceite que la tierra virgen. Las tierras

  5. Quantification of cross-bleaching during infrared (IR) light stimulation

    Kreutzer, Sebastian; Hülle, Daniela; Thomsen, Kristina Jørkov; Hilgers, Alexandra; Kadereit, Annette; Fuchs, Markus

    2013-01-01

    1 at the time” option can result in significant dose underestimation (1) if the sequence is not split into different sets, or (2) if samples are not placed on every 2nd position. In addition, a newly designed flange for the optical unit of the TL/OSL reader is presented which appears to reduce cross-bleaching......The cross-bleaching behaviour of automated Risø TL/OSL (DA-12, DA-15, DA-20) luminescence readers is investigated. By design, up to 24 or 48 aliquots can be stored on a carousel in a single measurement chamber. Due to this construction, irradiation or illumination on one sample may affect the...... adjacent position resulting in systematic errors. Previously reported for blue LEDs, such cross-talk (cross-bleaching/illumination) has never been quantified explicitly for the infrared (IR) LEDs, although they are intensively used in IRSL measurements of e.g. feldspar and polymineral samples. In IRSL...

  6. Ten years after bleaching - facing the consequences of climate change in the Indian Ocean.CORDIO Status Report 2008.

    Grimsditch, G.; Mwaura, J.; Kilonzo, J.; Amiyo, N.; Obura, D.

    2008-01-01

    When a coral bleaches, the obligate symbiosis between the coral polyp and the micro-algal zooxanthellae is disrupted and the zooxanthellae are expelled from the polyp. Although a bleached coral does not necessarily die, it is more vulnerable to disease, algal overgrowth, bioerosion and eventually mortality. Mass bleaching and mortality events in the last decade have prompted increased research into zooxanthellae, and it is possible that zooxanthellae population strategies affect a coral’s tol...

  7. Spring ``bleaching'' among Pocillopora in the Sea of Cortez, Eastern Pacific

    Lajeunesse, T. C.; Reyes-Bonilla, H.; Warner, M. E.

    2007-06-01

    A mild bleaching event was observed among Pocillopora spp. in the southern Gulf of California in the spring of 2006. Uniform bleaching occurred in numerous colonies on the upper portions of their branches. Most (˜90%) colonies that exhibited bleaching contained a species of endosymbiotic dinoflagellate, Symbiodinium C1b-c, which differed from the Symbiodinium D1 found inhabiting most unbleached colonies. Analysis of chlorophyll fluorescence, indicated a decline in photosystem II photochemical activity, especially among colonies populated with C1b-c. By early August, most affected colonies had recovered their normal pigmentation and fluorescence values were once again high for all colonies. No mortality was observed among tagged bleached colonies nor did symbiont species composition change during recovery. This unusual episode of bleaching did not appear to be a response to thermal stress, but may have been triggered by high levels of solar radiation during a period of unseasonally high water clarity in the early spring.

  8. Coral Mortality and Bleaching Output

    COMBO is a spreadsheet-based model for the use of managers, conservationists, and biologists for projecting the effects of climate change on coral reefs at local-to-regional scales. The COMBO (Coral Mortality and Bleaching Output) model calculates the impacts to coral reefs from...

  9. Coral reef bleaching and sea surface temperature anomalies: 1991-1996 global patterns

    Goreau, T.J.; Hayes, R.L.; Strong, A.

    1997-12-31

    Global spatio-temporal patterns of mass coral reef bleaching during the first half of the 1990s continued to show the strong temperature correlations which first became established in the 1980s. Satellite sea surface temperature data and field observations were used to track thermal bleaching events in real time. Most bleaching events followed warm season sea surface temperature anomalies of around +1 degree celsius above historical means. Global bleaching patterns appear to have been strongly affected by worldwide cooling which followed eruption of Mount Pinatubo in June 1991. High water temperatures and mass coral reef bleaching took place in the Caribbean, Indian Ocean, and South Pacific in 1991, but there were few thermal anomalies or bleaching events in 1992 and 1993, years which were markedly cooler worldwide. Following the settling of Mount Pinatubo aerosols and resumption of global warming trends, extensive ocean thermal hot spots and bleaching events resumed in the South Pacific, South Atlantic, and Indian Oceans in 1994. Bleaching again took place in hot spots in the Indian Ocean and Caribbean in 1995, and in the South Atlantic, Caribbean, South Pacific, North Pacific, and Persian Gulf in 1996. Coral reefs worldwide are now very close to their upper temperature tolerance limits. This sensitivity, and the fact that the warmest ecosystems have no source of immigrant species pre-adapted to warmer conditions, may make coral reef ecosystems the first to be severely impacted if global temperatures and sea levels remain at current values or increase further.

  10. The effect of elapsed time following bleaching on enamel bond strength of resin composite.

    Cavalli, V; Reis, A F; Giannini, M; Ambrosano, G M

    2001-01-01

    Recent studies have concluded that carbamide peroxide bleaching agents significantly affect the bond strength of composite to bleached enamel. This study evaluated the effects of bleaching regimen with different carbamide peroxide concentrations and post-treatment times on composite bond strength to enamel. Two hundred and four flat buccal and lingual enamel surfaces obtained from erupted sound third molars were randomly divided into 17 groups (n = 12). Sixteen experimental groups comprised the evaluation of four carbamide peroxide home bleaching agents (Opalescence 10%-20% and Whiteness 10%-16%) and four time intervals after bleaching (one day, one, two and three weeks). Specimens of control group were not submitted to bleaching and were stored in artificial saliva at 37 degrees C for 10 days. The specimens of experimental groups were exposed to one daily application of carbamide peroxide for six hours for 10 consecutive days. After each daily treatment and post-bleaching, the specimens were stored in artificial saliva solution. Bonds were formed with Scotchbond MP and Z-100 composite resin, and shear bond test was carried out 24 hours after adhesive-composite application. Two-way ANOVA showed that the bond strengths were significantly different (p < 0.05). For the first two weeks post-bleaching, the bond strengths of resin to enamel were low. After a lapse of three weeks, the bond strength returned to that of the untreated control group. Increased concentration did not prolong the time needed prior to bonding. PMID:11699184

  11. ECF bleaching with a final hydrogen peroxide stage: Impact of the chemical composition of Eucalyptus globulus kraft pulps

    Loureiro, Pedro E. G.; Eva F. Domingues; Evtuguin, Dmitry V.; M. Graça Videira Sousa Carvalho

    2010-01-01

    Two industrial elemental chlorine free (ECF) bleaching sequences, D0(EOP)D1(EP)D2 and OQ(PO)DP, are compared with respect to the bulk content of lignin, carboxyl, hexeneuronic acids (HexA), and reducing groups after each bleaching stage. HexA groups contribute significantly to the total content of carboxyl groups, and their degradation during chlorine dioxide bleaching is reflected by a decrease of the carboxyl content. The higher degradation using an enhanced use of oxygen-based bleaching ch...

  12. Cloning and transcriptional analysis of Crepis alpina fatty acid desaturases affecting the biosynthesis of crepenynic acid.

    Nam, Jeong-Won; Kappock, T Joseph

    2007-01-01

    Crepis alpina acetylenase is a variant FAD2 desaturase that catalyses the insertion of a triple bond at the Delta12 position of linoleic acid, forming crepenynic acid in developing seeds. Seeds contain a high level of crepenynic acid but other tissues contain none. Using reverse transcriptase-coupled PCR (RT-PCR), acetylenase transcripts were identified in non-seed C. alpina tissues, which were highest in flower heads. To understand why functional expression of the acetylenase is limited to seeds, genes that affect acetylenase activity by providing substrate (FAD2) or electrons (cytochrome b5), or that compete for substrate (FAD3), were cloned. RT-PCR analysis indicated that the availability of a preferred cytochrome b5 isoform is not a limiting factor. Developing seeds co-express acetylenase and FAD2 isoform 2 (FAD2-2) at high levels. Flower heads co-express FAD2-3 and FAD3 at high levels, and FAD2-2 and acetylenase at moderate levels. FAD2-3 was not expressed in developing seed. Real-time RT-PCR absolute transcript quantitation showed 10(4)-fold higher acetylenase expression in developing seeds than in flower heads. Collectively, the results show that both the acetylenase expression level and the co-expression of other desaturases may contribute to the tissue specificity of crepenynate production. Helianthus annuus contains a Delta12 acetylenase in a polyacetylene biosynthetic pathway, so does not accumulate crepenynate. Real-time RT-PCR analysis showed relatively strong acetylenase expression in young sunflowers. Acetylenase transcription is observed in both species without accumulation of the enzymatic product, crepenynate. Functional expression of acetylenase appears to be affected by competition and collaboration with other enzymes. PMID:17329262

  13. Effect of casein phosphopeptide-amorphous calcium phosphate on the flexural strength of enamel-dentin complex following extracoronal bleaching

    Diatri Nari Ratih

    2015-03-01

    Full Text Available Background: Bleaching can affect the mechanical properties of enamel-dentin complex, such as flexural strength. Casein phosphopeptide-amorphus calcium phosphate (CPP-ACP is often used following bleaching treatment to reduce hypersensitivity and to increase demineralization of tooth. Purpose: The purpose of the study was to investigate the effect of CPP-ACP on the flexural strength of enamel-dentin complex following extracoronal bleaching. Methods: Forty-eight enamel-dentin plates (size 8 x 2 x 3 mm were randomly assigned into 6 groups, each consisted of 8 samples. Group 1, no bleaching and immersed in artificial saliva. Group 2, no bleaching, CPP-ACP application only. Group 3, bleaching using 15% carbamide peroxide. Group 4, similar to group 3, except application of CPP-ACP for the times between bleaching. Group 5, bleaching with 40% hydrogen peroxide. Group 6, similar to group 5, except application of CPP-ACP for the times between bleaching. Flexural strength of each enamel-dentin plate was tested by threepoint bending test using universal testing machine. Results: The results showed that 15% carbamide peroxide and 40% hydrogen peroxide significantly reduced flexural strength of enamel-dentin (216.25±26.44 MPa and 206.67±32.07 MPa respectively. Conversely, application of CPP-ACP following both bleachings increased flexural strength (266.75± 28.27MPa and 254.58±36.59 MPa respectively. A two-way Anova revealed that extracoronal bleaching agents significantly reduced flexural strength (p<0.05. Conclusion: Extracoronal bleaching agents reduce flexural strength, whereas application of CPP-ACP following bleaching either with 15% carbamide peroxide or 40% hydrogen peroxide can increase the flexural strength of enamel-dentin complex.

  14. Augmenting acid with affective details to assess credibility

    Roland Fleck; Amber Hines; Cheryl Hiscock-Anisman; Kevin Colwell; Ryan Ansarra; Lindsey Cole; Delyana Belarde

    2011-01-01

    There is a need within the criminal justice systems of many countries to create a valid and applicable system of investigative interviewing and credibility assessment. The present study assesses the general validity one such system, called Assessment Criteria Indicative of Deception (ACID). ACID comprises interviewing strategies that facilitate the detection of deception and content criteria that highlight differences in verbal behavior. Sixty university undergraduates performed a staged thef...

  15. THE EFFECT OF TRANSITION METAL IONS-IRON ON HYDROGEN PEROXIDE BLEACHING

    YumengZhao; ShuhuiYang; LiangSheng; YonghaoNi

    2004-01-01

    Hydrogen peroxide bleaching has been extensivelyused in high-yield pulp bleaching. Unfortunately,hydrogen peroxide can be decomposed underalkaline condition, especially when transition metalions exit. Experiments show that the valence oftransition metal ion is also responsible for thedecomposition of hydrogen peroxide.Iron ions are present in two oxidation states, Fe2+ andFe3+. They are both catalytically active to hydrogenperoxide decomposition. Because Fe3+ is brown, itcan affect the brightness of pulp directly, it can alsocombine with phenol, forming complexes which notonly are stable structures and are difficult to beremoved from pulp, but also significantly affect thebrightness of pulp because of their color.Sodium silicate and magnesium sulfate, when usedtogether, can greatly decrease hydrogen peroxidedecomposition. The optimum dosage of sodiumsilicate is about 0.1% (on solution) for Fe2~ and0.25% (on solution) for Fe3~. Adding chelants such asDTPA or EDTA with stabilizers simultaneously canobviously improve pulp brightness. For iron ions, thechelate effect of DTPA is better than that of EDTA.Under acidic conditions, sodium hyposulfite andcellulose can reduce Fe3+ to Fez+ effectively, and pulpbrightness is improved greatly. Adding sodiumthiosulfate simultaneously with magnesium sulfate,sodium silicate, and DTPA to alkaline peroxidesolution can result in higher brightness of pulp.pH is a key parameter during hydrogen peroxidebleaching, the optimum pH value should be 10.5-12.

  16. Response of millepora alcicornis (Milleporina: Milleporidae) to two bleaching enventgs at Puerto Morelos reef, Mexican Caribbean

    Two naturally occurring colonies of Millepora alcicornis were monitored during 1997 and 1998, both years in which this species bleached in the Mexican Caribbean. One colony (HL) was naturally exposed to a high light environment and another nearby colony (LL) was exposed to 5.9 times lower light levels due to shadowing by a pier. For 10 days in August 1997, seawater temperatures in the surrounding reef lagoon rose up to 1.5 degrees C above the 6-year August average. The HL colony bleached to white during this period, whereas, the LL colony remained dark-brown colored. The HL colony recovered its normal dark-brown coloration (reversible bleaching) within several weeks, during which time the seawater temperatures returned to average. The following year, for 10 days, seawater temperatures rose up to 3 degrees C above the 7-year August average and both colonies bleached to white and neither colony recovered (irreversible bleaching). Both colonies were rapidly overgrown by algae and hydroids and, as of June 2003, no recovery has taken place. Prior to the 1997 bleaching, experiments using solar radiation showed that the quantum yield of photosystem II charge separation of branches from HL and LL colonies were affected for several hours by exposure to ultraviolet radiation (UVR, 280 to 400 nm), but recovered by the same evening, suggesting that UVR does not have long-term effects on photochemistry in M. alcicornis. In situ effective quantum yield of photosystem II charge separation (ΔF/Fm') measurements before the 1998 bleaching event indicate that both colonies were healthy in terms of the physiological status of their endosymbionts. During and after the 1998 bleaching event, both colonies showed a reduction in ΔF/Fm' and consequently an increase in excitation pressure on photosystem II. The data suggest that temperature is not the only factor that causes bleaching and that solar radiation may play an important role in coral bleaching. (Author)

  17. Retinoic Acid Signaling Affects Cortical Synchrony During Sleep

    Maret, Stéphanie; Franken, Paul; Dauvilliers, Yves; Ghyselinck, Norbert B.; Chambon, Pierre; Tafti, Mehdi

    2005-10-01

    Delta oscillations, characteristic of the electroencephalogram (EEG) of slow wave sleep, estimate sleep depth and need and are thought to be closely linked to the recovery function of sleep. The cellular mechanisms underlying the generation of delta waves at the cortical and thalamic levels are well documented, but the molecular regulatory mechanisms remain elusive. Here we demonstrate in the mouse that the gene encoding the retinoic acid receptor beta determines the contribution of delta oscillations to the sleep EEG. Thus, retinoic acid signaling, which is involved in the patterning of the brain and dopaminergic pathways, regulates cortical synchrony in the adult.

  18. Optical bleaching studies of quartz

    The bleaching properties of a hydrothermal, Arkansas quartz are studied in detail. The thermoluminescence (TL) and phototransferred TL (PTTL) signals are examined as a function of wavelength, illumination time and temperature at which the sample is illuminated. We have also briefly studied the effects of pre-irradiation annealing on the sample. The results of these experiments are described and their relevance to the models for TL is discussed. (Author)

  19. Study on Bleaching Technology of Cotton Fabric with Sodium Percarbonate

    Li Zhi

    2016-01-01

    Full Text Available Bleach cotton fabric with sodium percarbonate solution. Analyse of the effect of the concentration of sodium percarbonate solution, bleaching time, bleaching temperature and the light radiation on the bleaching effect of fabric.The result shows that increasing concentrations of percarbonate,increasing the bleaching time , raising the bleaching temperature and the UV irradiation may whiten the cotton fabric.The most suitable conditions for the bleaching process is concentration of sodium percarbonate solution 6 g/ L, bleaching temperature 80°C and bleaching time 60 min.

  20. The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

    Kátia Maria Morais Eiras

    2009-01-01

    Full Text Available Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxide in sequences ending with a chlorine dioxide stage but similarly in sequences ending with a final peroxide stage. The use of secondary condensate for pulp washing decreases reversion.

  1. RESPONSE SURFACE METHODOLOGY APPROACH FOR OPTIMIZATION OF FLAX SEED OIL BLEACHING PROCESS

    Miroslav Ondrejovič; Daniela Chmelová; Tibor Maliar

    2013-01-01

    Flax seed is an important source of omega-3 polyunsaturated fatty acids essential for human physiology. For low oxidation stability, specific taste and concomitant color compounds this oil is poorly applicable as nutraceutical additive. The aim of this study was optimization of flax seed oil bleaching. The optimal conditions for the bleaching process were determined using response surface methodology. A central composite design was used to investigate the effects of three independent variable...

  2. STUDIES ON XYLANASE AND LACCASE ENZYMATIC PREBLEACHING TO REDUCE CHLORINE-BASED CHEMICALS DURING CEH AND ECF BLEACHING

    Vasanta V. Thakur,

    2012-02-01

    Full Text Available The biobleaching efficiency of xylanase and laccase enzymes was studied on kraft pulps from wood and nonwood based raw materials employed in the Indian paper industry. Treatment of these pulps with xylanase enzyme could result in improved properties, showing 2.0% ISO gain in pulp brightness and/or reducing the demand of chlorine-based bleach chemicals by up to 15% with simultaneous reduction of 20 to 25% in AOX generation in bleach effluents. Further, mill-scale trial results revealed that enzymatic prebleaching can be successfully employed with xylanases to reach the same bleach boosting efficacy. Laccase bleaching was also studied on hardwood pulp at a pH around 8.0, where most of the pulp mills in India are operating, in contrast to earlier studies on laccase enzyme bleaching, which were conducted at acidic pHs, i.e. 4.0 to 5.0. In case of laccase bleaching, interesting results were found wherein a bleach-boosting effect was observed even at pH 8.0. Further studies carried out with HOBT as mediator in comparison to the commonly used and expensive ABTS laccase mediator system (LMS resulted in improvement of the bleaching efficiency with reduction in demand of chlorine dioxide by more than 35%. Potential for further reduction was indicated by the brightness gain, when compared with a control using the DE(pD bleach sequence.

  3. Evaluation of cotton-fabric bleaching using hydrogen peroxide and Blue LED

    de Oliveira, Bruno P.; Moriyama, Lilian T.; Bagnato, Vanderlei S.

    2015-06-01

    The raw cotton production requires multiple steps being one of them the removal of impurities acquired during previous processes. This procedure is widely used by textile industries around the world and is called bleaching. The raw cotton is composed by cellulosic and non-cellulosic materials like waxes, pectins and oils, which are responsible for its characteristic yellowish color. The bleaching process aims to remove the non-cellulosic materials concentration in the fabric, increasing its whiteness degree. The most used bleaching method utilizes a bath in an alkali solution of hydrogen peroxide, stabilizers and buffer solutions under high temperature. In the present study we evaluated the possibility of using a blue illumination for the bleaching process. We used blue LEDs (450 nm) to illuminate an acid hydrogen peroxide solution at room temperature. The samples treated by this method were compared with the conventional bleaching process through a colorimetric analysis and by a multiple comparison visual inspection by volunteers. The samples were also studied by a tensile test in order to verify the integrity of the cloth after bleaching. The results of fabric visual inspection and colorimetric analysis showed a small advantage for the sample treated by the standard method. The tensile test showed an increasing on the yield strength of the cloth after blue light bleaching. The presented method has great applicability potential due to the similar results compared to the standard method, with relative low cost and reduced production of chemical waste.

  4. Effectiveness of bleaching agent on composite resin discoloration

    Galih Sampoerno

    2012-03-01

    Full Text Available Background: The discoloration of teeth, especially anterior teeth, is one of aesthetic problems. The use of tooth bleaching agents for discolored natural teeth is becoming increasingly popular. Many dentists, however, get many problems when they conduct bleaching process since there is much composite filling on patient’s anterior teeth. Although many research have focused on the discoloration of composite resin after bleaching process, the problem still becomes debatable. Purpose: The purpose of this study was to investigate the difference of the discoloration between hybrid composite and nano composite before and after the application of tooth bleaching agent, 38% hydrogen peroxide. Methods: Eighteen disk-shaped specimens (5 mm of each of two composite resins, hybrid and nano filler, were prepared. The each group was treated 3 times and the specimens were divided into two groups consisted of 9 specimens for each, and then immersed in black tea solutions for 72 hours. Next, after having staining and bleaching processes, the color of the specimens was measured with a optic spectrophotometer by using photo with type BPY-47 and digital microvolt. The differences of the light intensity among three measurements were then calculated. Afterwards, GLM MANOVA Repeated Measure and parametric analysis (Independent t-test and Paired t-test were then used to analyze the data. Results: After staining process, it is then known that the nano composite had more discoloration and more affected by the black tea solution than the hybrid one. Conclusion: After bleaching, the discoloration was finally removed completely from both hybride and nano filler composite resins and became brighter from the baseline color.Latar belakang: Salah satu problem estetik adalah adanya perubahan warna pada gigi anterior. Peningkatan pemakaian bahan bleaching semakin popular. Banyak dokter gigi mempunyai problem ketika mereka akan melakukan proses bleaching dan ditemukan banyak

  5. Arachidonic Acid and Eicosapentaenoic Acid Metabolism in Juvenile Atlantic Salmon as Affected by Water Temperature

    Norambuena, Fernando; Morais, Sofia; Emery, James A.; Turchini, Giovanni M.

    2015-01-01

    Salmons raised in aquaculture farms around the world are increasingly subjected to sub-optimal environmental conditions, such as high water temperatures during summer seasons. Aerobic scope increases and lipid metabolism changes are known plasticity responses of fish for a better acclimation to high water temperature. The present study aimed at investigating the effect of high water temperature on the regulation of fatty acid metabolism in juvenile Atlantic salmon fed different dietary ARA/EPA ratios (arachidonic acid, 20:4n-6/ eicosapentaenoic acid, 20:5n-3), with particular focus on apparent in vivo enzyme activities and gene expression of lipid metabolism pathways. Three experimental diets were formulated to be identical, except for the ratio EPA/ARA, and fed to triplicate groups of Atlantic salmon (Salmo salar) kept either at 10°C or 20°C. Results showed that fatty acid metabolic utilisation, and likely also their dietary requirements for optimal performance, can be affected by changes in their relative levels and by environmental temperature in Atlantic salmon. Thus, the increase in temperature, independently from dietary treatment, had a significant effect on the β-oxidation of a fatty acid including EPA, as observed by the apparent in vivo enzyme activity and mRNA expression of pparα -transcription factor in lipid metabolism, including β-oxidation genes- and cpt1 -key enzyme responsible for the movement of LC-PUFA from the cytosol into the mitochondria for β-oxidation-, were both increased at the higher water temperature. An interesting interaction was observed in the transcription and in vivo enzyme activity of Δ5fad–time-limiting enzyme in the biosynthesis pathway of EPA and ARA. Such, at lower temperature, the highest mRNA expression and enzyme activity was recorded in fish with limited supply of dietary EPA, whereas at higher temperature these were recorded in fish with limited ARA supply. In consideration that fish at higher water temperature

  6. Wood Properties of Poplar from Stand Affected by Acid Rain

    2002-01-01

    Wood properties from 28 trees (Populus euramericana) selected from healthy and acid rain damaged forest were measured to evaluate the possible impacts on wood quality and utilization. On the heavily damaged location, the pH value of precipitation ranged from 3.7-5.0, and sulfate loading ranged from 20-40 kg·ha-2.y-1. Quantitative and qualitative studies on ring width, physical properties and mechanical properties indicated that changes of wood properties between diseased and healthy poplar occurred. Aci...

  7. Microhardness of demineralized enamel following home bleaching and laser-assisted in office bleaching

    Ghanbarzadeh, Majid; Akbari, Majid; Hamzei, Haniye

    2015-01-01

    Background There is little data regarding the effect of tooth whitening on microhardness of white spot lesions. This study was conducted to investigate the effect of home-bleaching and laser-assisted in-office bleaching on microhardness of demineralized enamel. Material and Methods Forty bovine incisors were selected and immersed in a demineralizing solution for 12 weeks to induce white spot lesions. Enamel blocks were prepared and randomly assigned to two groups of 20 each. The first group underwent home bleaching with 15% carbamide peroxide which was applied for 8 hours a day over a period of 15 days. In the second group, in-office bleaching was performed by 40% hydrogen peroxide and powered by irradiation from an 810 nm gallium-aluminum-arsenide (GaAlAs) diode laser (CW, 2W). This process was performed for 3 sessions every seven days, in 15 days. The specimens were stored in Fusayama Meyer artificial saliva during the experiment. Surface microhardness was assessed before and after the bleaching therapies in both groups. Results Microhardness decreased significantly following both home bleaching and laser-assisted in-office bleaching (plaser-assisted in-office bleaching can result in a significant reduction in microhardness of white spot lesions. Therefore, it is suggested to take protective measures on bleached demineralized enamel. Key words:White spot lesion, bleaching, laser, microhardness, demineralized enamel, home bleaching, in-office bleaching. PMID:26330939

  8. Influence of bleach activators on the fabric made from cotton (gossypium hamster l.)

    Raw cotton contains various type of trash and most of the impurities are removed during the spinning process but still the cotton fabric coming from the weaving or knitting process always contains some impurities. Some time cotton fabric gets the oil, stains and coloured materials which affect the quality of dyed fabric. Bleaching is a process that eliminates unwanted coloured matters from the fibres, yarn and fabrics. A bleaching agent is a material that lightens or whitens a substrate through chemical action. Hydrogen peroxide is by far the most commonly used oxidative bleaching agent for cotton and its blends, accounting for more than 90 percent of all the bleaching agents. The use of activators to enhance the bleaching performance of hydrogen peroxide for cellulosic materials has gained popularity now a day. In this context the main objectives of this paper are to study the influence of different bleaching activators on cotton fabric and to give implications for textile extension.The results indicate that the activators with different concentrations, along with different concentrations of hydrogen peroxide (H/sub 2/O/sub 2) have significant influence on the bleaching performance of cotton fabric. (author)

  9. Effect of three nanobiomaterials on the surface roughness of bleached enamel

    Maryam Khoroushi

    2015-01-01

    Full Text Available Background: The ever-increasing demand for enhanced esthetic appearance has resulted in significant developments in bleaching products. However, the enamel surface roughness (SR might be negatively affected by bleaching agents. This in vitro study was undertaken to compare the effects of three nanobiomaterials on the enamel SR subsequent to bleaching. Materials and Methods: The crowns of six extracted intact nonerupted human third molars were sectioned. Five dental blocks measuring 2 mm × 3 mm × 4 mm were prepared from each tooth and placed in colorless translucent acrylic resin. The enamel areas from all the specimens were divided into five groups (n = 6: Group 1 did not undergo any bleaching procedures; Group 2 was bleached with a 40% hydrogen peroxide (HP gel; Groups 3, 4, and 5 were bleached with a 40% HP gel modified by bioactive glass (BAG, amorphous calcium phosphate, and hydroxyapatite, respectively. The enamel SR was evaluated before and after treatment by atomic force microscopy. The data were analyzed by Kruskal–Wallis and Mann–Whitney tests. Results: SR increased significantly in the HP group. SR decreased significantly in the HP gel modified by BAG group as compared to other groups. Conclusions: Within the limitations of this study, incorporation of each one of the three test biomaterials proved effective in decreasing enamel SR subsequent to in-office bleaching technique.

  10. Short-Term Coral Bleaching Is Not Recorded by Skeletal Boron Isotopes

    Schoepf, Verena; Malcolm T McCulloch; Mark E Warner; Stephen J Levas; Matsui, Yohei; Aschaffenburg, Matthew D.; Andréa G Grottoli

    2014-01-01

    Coral skeletal boron isotopes have been established as a proxy for seawater pH, yet it remains unclear if and how this proxy is affected by seawater temperature. Specifically, it has never been directly tested whether coral bleaching caused by high water temperatures influences coral boron isotopes. Here we report the results from a controlled bleaching experiment conducted on the Caribbean corals Porites divaricata, Porites astreoides, and Orbicella faveolata. Stable boron (δ11B), carbon (δ1...

  11. Influence of Coral Bleaching on the Fauna of Tutia Reef, Tanzania

    Öhman, M.C.; Lindahl, U.; Schelten, C.K.

    1999-01-01

    In 1998, coral reefs of Tanzania were severely affected by bleaching. The coral mortality that followed caused a concern for coral reef degradation and overall resource depletion. In this study, we investigated coral bleaching effects on the coral reef fauna at Tutia Reef in Mafia Island Marine Park, Tanzania. Corals from adjacent reef patches of the species Acropora formosa were transplanted into plots, and reef structure and associated fish assemblages were examined before and after the ble...

  12. Low irradiances affect abscisic acid, indole-3-acidic acid, and cytokinin levels of wheat (Triticum aestivum L.) tissues

    Nan, R.; Carman, J. G.; Salisbury, F. B.

    1999-01-01

    Wheat (Triticum aestivum L.) plants were grown under four irradiance levels: 1,400, 400, 200, and 100 micromol m-2 s-1. Leaves and roots were sampled before, during, and after the boot stage, and levels of abscisic acid (ABA), indole-3-acetic acid (IAA), zeatin, zeatin riboside, dihydrozeatin, dihydrozeatin riboside, isopentenyl adenine, and isopentenyl adenosine were quantified using noncompetitive indirect ELISA systems. Levels of IAA in leaves and roots of plants exposed to 100 micromol m-2 s-1 of irradiance were 0.7 and 2.9 micromol kg-1 dry mass (DM), respectively. These levels were 0.2 and 1.0 micromol kg-1 DM, respectively, when plants were exposed to 1,400 micromol m-2 s-1. Levels of ABA in leaves and roots of plants exposed to 100 micromol m-2 s-1 were 0.65 and 0.55 micromol kg-1 DM, respectively. They were 0.24 micromol kg-1 DM (both leaves and roots) when plants were exposed to 1,400 micromol m-2 s-1. Levels of isopentenyl adenosine in leaves (24.3 nmol kg-1 DM) and roots (29.9 nmol kg-1 DM) were not affected by differences in the irradiance regime. Similar values were obtained in a second experiment. Other cytokinins could not be detected (<10 nmol kg 1 DM) in either experiment with the sample sizes used (150-600 mg DM for roots and shoots, respectively).

  13. Habitat and Bleaching in the Foraminiferan Peneroplis Pertusus

    Ellison, Aimee

    2006-01-01

    The effects of human activities on the earth’s environment have gained increasing attention in recent years. With coral reefs declining worldwide, efficient tools for assessing reef health are more important than ever. The species of larger foraminifera known as Peneroplis pertusus share key characteristics with reef building corals. By examining the populations’ natural distribution along with the abiotic factors affecting bleaching, a better understanding of reef systems as a whole is a...

  14. Physicochemical properties and oxidative stability of bleached pomace-olive oil on Tunisian activated clays

    This work is a contribution to studying bleaching process, which is an important stage in refining of vegetable oils. This process permitted to reduce or convert undesired constituents to harmless ones from oils and fats. Virgin olive oil, considered as reference, and pomace-olive oil were bleached in optimal conditions using Tunisian activated clays ( collected from the South of Tunisia) which were prepared in our laboratory and compared with commercial bleaching earths. It was shown that activated Tunisian clays are characterized by a very important adsorptive capacity, which is similar to that of commercial ones. In addition, the study of physicochemical properties of bleached oils was considered. The fatty acid composition (GC), the triacylglycerol composition (HPLC), and oxidative stability (UV spectrometry) allowed to conclude that treated oils do not undergo considerable physicochemical alterations and their caracteristics remain in concordance with international standards relative to edible refined oils. (Author)

  15. Post-bleaching application of an antioxidant on dentin bond strength of three dental adhesives

    Khoroushi, Maryam; Saneie, Tahereh

    2012-01-01

    Background: Antioxidizing agents have recently been suggested to compensate decreased bond strength of resin materials to bleached tooth tissues. This study compared the shear bond strength (SBS) of three different adhesives on bleached dentin immediately after bleaching, bleached/delayed for 1 week, and bleached/applied antioxidizing agent. Materials and Methods: The dentinal surfaces of 132 intact extracted molars were prepared and divided into 12 groups. The following adhesives were investigated: Optibond FL (OFL) (three-step etch-and-rinse), Optibond Solo Plus (two-step etch-and-rinse), and Optibond all-in-one (OA) (one-step self-etch) (Kerr, Orange, USA). Unbleached dentin groups (groups 1-3) were prepared as negative controls (NC). The remainder surfaces (groups 4-12) were bleached with 20% Opalescent PF (Ultradent, USA). Specimens were bonded immediately after bleaching (groups 4-6), after 1 week (groups 7-9), or after using 10% sodium ascorbate (SA) gel (groups 10-12). Subsequent to bonding of composite resin, the samples were tested for SBS and analyzed using Kruskal-Wallis and Mann-Whitney tests (α=0.05). Results: Regarding control groups, OA showed the highest SBS among the studied adhesives (P0.05) except the of delay bonding with OA. Conclusions: The findings suggest that bond strength of resin to bleached dentin may be affected with the adhesive system. Reduced SBS to bleached dentin can be amended by the use of SA as an antioxidizing agent. However, the amount of reversed bond strength subsequent to applying antioxidant might be related to the kind of dental adhesive. PMID:22363363

  16. An Effective Ostrich Oil Bleaching Technique Using Peroxide Value as an Indicator

    Gan Seng Chiew

    2011-07-01

    Full Text Available Ostrich oil has been used extensively in the cosmetic and pharmaceutical industries. However, rancidity causes undesirable chemical changes in flavour, colour, odour and nutritional value. Bleaching is an important process in refining ostrich oil. Bleaching refers to the removal of certain minor constituents (colour pigments, free fatty acid, peroxides, odour and non-fatty materials from crude fats and oils to yield purified glycerides. There is a need to optimize the bleaching process of crude ostrich oil prior to its use for therapeutic purposes. The objective of our study was to establish an effective method to bleach ostrich oil using peroxide value as an indicator of refinement. In our study, we showed that natural earth clay was better than bentonite and acid-activated clay to bleach ostrich oil. It was also found that 1 hour incubation at a 150 °C was suitable to lower peroxide value by 90%. In addition, the nitrogen trap technique in the bleaching process was as effective as the continuous nitrogen flow technique and as such would be the recommended technique due to its cost effectiveness.

  17. In vitro penetration of bleaching agents into the pulp chamber

    Benetti, Ana Raquel; Valera, M C; Mancini, M N G;

    2004-01-01

    To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures.......To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures....

  18. REEF MANAGER'S GUIDE TO CORAL BLEACHING

    A Reef Manager's Guide to Coral Bleaching is the result of a collaborative effort by over 50 scientists and managers to: (1) engage in information-sharing in the areas of coral reef science and management for climate change and coral bleaching; and (2) compile a management tool ...

  19. On luminescence bleaching of tidal channel sediments

    Fruergaard, Mikkel; Pejrup, Morten; Murray, Andrew S.;

    2015-01-01

    We investigate the processes responsible for bleaching of the quartz OSL signal from tidal channel sediment. Tidal dynamics are expected to play an important role for complete bleaching of tidal sediments. However, no studies have examined the amount of reworking occurring in tidal channels and o...

  20. A bleaching earth from egyptian local deposits

    El Kinawy, Omayma S.

    2001-10-01

    Full Text Available The present investigation deals with the bleaching of vegetable oils using activated clays collected from some deposits in Egypt as compared to Tonsil FF currently used by local oil industry. The comparison was made; not only on the basis of the decolourising power of the earth, but also on the basis of its effects on the oil acidity, formation of the oil peroxides and the decomposition rate of the formed peroxides to aldehydes and ketones during the bleaching process. The activation of the collected earth samples was made using 4N HCl, 6N HCl and 30 % H2SO4. The bleaching tests of the activated samples were performed using the major four oil types processed in Egypt being cottonseed, sunflower, soybean and palm oils. In addition to the laboratory-evaluation tests, the performance of the activated samples, which showed promise on the lab-scale have been also tested on an industrial scale. The industrial application has proved that the activated local earth's can be successfully used as bleaching earth of local oils. Thus it can be used as a substitute of the varieties currently imported and used by the local oil sector.La presente investigación trata de la decoloración de aceites vegetales usando tierras activadas obtenidas de yacimientos egipcios, comparándola con el Tonsil FF usado normalmente en la industria oleícola local. La comparación se realizó, no sólo sobre la base del poder decolorante de la tierra, sino también sobre la base de sus efectos en la acidez del aceite, la formación de peróxidos y la velocidad de descomposición de los peróxidos formados en aldehidos y cetonas durante el proceso de decoloración. La activación de las muestras de tierras recogidas se hizo utilizando ClH 4N, ClH 6N y H2SO4 30 %. Los tests de decoloración de las muestras activadas se llevaron a cabo usando los cuatro tipos mayoritarios de aceites procesados en Egipto: aceite de semilla de algodón, de girasol, de soja y de palma. Además de los

  1. Utilization of concentrate of membrane filtration of bleach plant effluent in brick production

    Utilization potential of membrane filtration retentate (concentrate) of bleach plant effluent from paper industry, in bricks production, was investigated in the present study. Bricks were prepared by using retentate of membrane filtration in place of water. The physical properties measured for bricks were dimensions, density, moisture content, compressive strength, water absorption and porosity. Chemical analysis of the bricks was performed for water leachability and acid leachability, using ASTM Standard methods D 3987-06 and D 5233-92 respectively. The leachate samples were analyzed for Al, Cu, Fe, Co, Cr, Pb, Ni and Zn using AAS (atomic absorption spectrophotometer). Adsorbable organic halides (AOX) of leachate were analyzed by using AOX analyzer model ECS 1200 using column method. It was observed that the physical and chemical properties of bricks especially fire clay bricks were not adversely affected by the use of wastewater. Therefore, the organic matter of the retentate of membrane filtration creates no problems for this application.

  2. Removal of lead from aqueous solutions with a treated spent bleaching earth

    A spent bleaching earth from an edible oil refinery has been treated by impregnation with a normal sodium hydroxide solution followed by mild thermal treatment (100 deg. C). The obtained material (TSBE) was washed, dried and characterized by X-ray diffraction, FTIR, SEM, BET and thermal analysis. The clay structure was not apparently affected by the treatment and the impregnated organic matter was quantitatively removed. We have investigated the sorption of lead on this material, the spent bleaching earth (SBE) and the virgin bleaching earth (VBE). The kinetic results fit the pseudo second-order kinetic model and the Weber and Morris, intraparticle diffusion model. The pH had effect on the sorption efficiency. The sorption isotherms followed the Langmuir model for various sorbent concentrations with good values of determination coefficient. A comparison between the results obtained with this material and those of the literature highlighted a good removal capacity of the treated spent bleaching earth at low cost

  3. Short-term coral bleaching is not recorded by skeletal boron isotopes.

    Verena Schoepf

    Full Text Available Coral skeletal boron isotopes have been established as a proxy for seawater pH, yet it remains unclear if and how this proxy is affected by seawater temperature. Specifically, it has never been directly tested whether coral bleaching caused by high water temperatures influences coral boron isotopes. Here we report the results from a controlled bleaching experiment conducted on the Caribbean corals Porites divaricata, Porites astreoides, and Orbicella faveolata. Stable boron (δ11B, carbon (δ13C, oxygen (δ18O isotopes, Sr/Ca, Mg/Ca, U/Ca, and Ba/Ca ratios, as well as chlorophyll a concentrations and calcification rates were measured on coral skeletal material corresponding to the period during and immediately after the elevated temperature treatment and again after 6 weeks of recovery on the reef. We show that under these conditions, coral bleaching did not affect the boron isotopic signature in any coral species tested, despite significant changes in coral physiology. This contradicts published findings from coral cores, where significant decreases in boron isotopes were interpreted as corresponding to times of known mass bleaching events. In contrast, δ13C and δ18O exhibited major enrichment corresponding to decreases in calcification rates associated with bleaching. Sr/Ca of bleached corals did not consistently record the 1.2°C difference in seawater temperature during the bleaching treatment, or alternatively show a consistent increase due to impaired photosynthesis and calcification. Mg/Ca, U/Ca, and Ba/Ca were affected by coral bleaching in some of the coral species, but the observed patterns could not be satisfactorily explained by temperature dependence or changes in coral physiology. This demonstrates that coral boron isotopes do not record short-term bleaching events, and therefore cannot be used as a proxy for past bleaching events. The robustness of coral boron isotopes to changes in coral physiology, however, suggests that

  4. Bleaching in vital teeth: a literary review

    Felipe Fagundes Soares

    2008-01-01

    Full Text Available Tooth bleaching technique has presented a significant evolution, promoting higher satisfaction and comfort to the patients. Therefore, the aim of this study was to present the bleaching agents and the techniques, discussing advantages and disadvantages of each one, and the effect of these agents in the oral environment. The main agents used in the bleaching technique are the hydrogen peroxide and the carbamide peroxide, promoting the bleaching effect through oxidation of organic compounds. The application of these agents can be made at home or at a doctor office. During treatment, it may occur some adverse effects, such as tooth sensibility, increasing of dental porosity, and some interactions with the restorative material. However, these adverse effects can be eliminated or controlled when the treatment is executed under professional orientation. When the bleaching technique is well indicated and correctly conducted, it is associated with significantly positive results.

  5. [Gingival bleaching: teaching and ethnocentrism].

    Bolla, Edson Daruich; Goldenberg, Paulete

    2010-06-01

    The aim of this study was to identify buccal/gingival cosmetic dentistry patterns subjacent to formation and professional practice of the dental surgeon from the ethnocentrism point of view. This is an exploratory study with a qualitative approach based on the thematic analysis. Initially a documental analysis was carried out. Thereafter, dental surgeons were interviewed and semi-structured questions were applied. In the Periodontal teaching field, this study showed that the presence of racial melanosis is omitted or treated as an alteration in the normality patterns and it is considered anti-aesthetic. All the interviewers learnt how to practice gingival bleaching in the post-graduation courses, they were all encouraged to offer this cosmetic dentistry procedure with the opportunity of obtaining a beautiful and healthy smile, thus assuring the belief of the Caucasian racial aesthetic superiority. This study make us think that the offer of gingival bleaching is oriented by the Caucasian pattern of beauty evidencing the ethnocentric character of this procedure. PMID:20640340

  6. Optical bleaching, TSL and OSL features of CVD diamond

    Luminescence and optical features of chemical vapour deposition (CVD) diamond have been studied in view of the potential application of this material in ionising radiation dosimetry field. For this purpose, thermally stimulated luminescence (TSL) and optically stimulated luminescence (OSL) techniques have been used. A large amount of work has emphasised the excellent dosimetric properties of CVD diamond. Nevertheless, TSL measurements showed that after irradiation, this material is extremely sensitive to ambient light and the stored dose information is drastically affected by optical bleaching. From OSL analysis, it follows that both types of processes (TSL and OSL) were characterised by the same excitation and emission spectra and that optical bleaching originated from a broad stimulation band lying from visible to near infrared with a continuous character. (authors)

  7. Whole transcriptome analysis reveals changes in expression of immune-related genes during and after bleaching in a reef-building coral

    Pinzón, Jorge H.; Kamel, Bishoy; Burge, Colleen A.; Harvell, C. Drew; Medina, Mónica; Weil, Ernesto; Mydlarz, Laura D.

    2015-01-01

    Climate change is negatively affecting the stability of natural ecosystems, especially coral reefs. The dissociation of the symbiosis between reef-building corals and their algal symbiont, or coral bleaching, has been linked to increased sea surface temperatures. Coral bleaching has significant impacts on corals, including an increase in disease outbreaks that can permanently change the entire reef ecosystem. Yet, little is known about the impacts of coral bleaching on the coral immune system...

  8. Local bleaching thresholds established by remote sensing techniques vary among reefs with deviating bleaching patterns during the 2012 event in the Arabian/Persian Gulf.

    Shuail, Dawood; Wiedenmann, Jörg; D'Angelo, Cecilia; Baird, Andrew H; Pratchett, Morgan S; Riegl, Bernhard; Burt, John A; Petrov, Peter; Amos, Carl

    2016-04-30

    A severe bleaching event affected coral communities off the coast of Abu Dhabi, UAE in August/September, 2012. In Saadiyat and Ras Ghanada reefs ~40% of the corals showed signs of bleaching. In contrast, only 15% of the corals were affected on Delma reef. Bleaching threshold temperatures for these sites were established using remotely sensed sea surface temperature (SST) data recorded by MODIS-Aqua. The calculated threshold temperatures varied between locations (34.48 °C, 34.55 °C, 35.05 °C), resulting in site-specific deviations in the numbers of days during which these thresholds were exceeded. Hence, the less severe bleaching of Delma reef might be explained by the lower relative heat stress experienced by this coral community. However, the dominance of Porites spp. that is associated with the long-term exposure of Delma reef to elevated temperatures, as well as the more pristine setting may have additionally contributed to the higher coral bleaching threshold for this site. PMID:26971815

  9. Effects of light activated in-office bleaching on permeability, microhardness, and mineral content of enamel.

    Parreiras, S O; Vianna, P; Kossatz, S; Loguercio, A D; Reis, A

    2014-01-01

    The aim of this study was to evaluate the permeability (PE), microhardness (KHN), and mineral change in enamel after LED/laser activated in-office bleaching. For PE, the coronal portion of premolars (n=51) was subjected to bleaching with 35% hydrogen peroxide (Whiteness HP Maxx, FGM Dental Products, Joinville, SC, Brazil). The samples were stained via the histochemical method, which involves a copper sulphate solution and rubeanic acid. The penetration of dye into the enamel was measured. The KHN of enamel was assessed before treatment, immediately after the bleaching treatment, and again after one week. The calcium and phosphorus content were analyzed with a scanning electron microscope with energy-dispersive X-ray (JSM 6360LV, Jeol Ltd, Tokyo, Japan). The data set from each test was subjected to appropriate parametric statistical analysis (α=0.05). No significant differences were observed for PE in NLA and LA compared to the control group (p=0.98), as well as for calcium (p=0.16) and phosphorus (p=0.80) content. Significant reduction of KHN after bleaching occurred for both groups (p<0.001). After immersion in artificial saliva, the KHN of the enamel for all groups was similar to that seen before bleaching. Light activation during in-office bleaching does not produce significant changes in the enamel compared to a non-light-activated technique. PMID:24815914

  10. Trans fatty acid intake is related to emotional affect in the Adventist Health Study-2.

    Ford, Patricia A; Jaceldo-Siegl, Karen; Lee, Jerry W; Tonstad, Serena

    2016-06-01

    Trans fatty acids in Western diets increase health risks, and have been associated with the risk of depression. We hypothesized that intakes of trans fatty acids (primarily from margarines and baked goods) were inversely associated with positive affect and positively associated with negative affect in a longitudinal study. Church attendees residing in North America completed a food frequency questionnaire in 2002-6 as part of the Adventist Health Study-2. A subset in which we excluded participants with established cardiovascular disease (n=8,771) completed the Positive and Negative Affect Schedule (PANAS) in 2006-7. The associations between dietary intakes of fatty acids to positive and negative affect were tested with linear regression analysis controlling for age, gender, ethnicity, education, body mass index, exercise, sleep, sleep squared, Mediterranean diet, total energy intake and alcohol. Intakes of trans fatty acids were inversely associated with positive affect (β=-0.06, B=-0.27 [95% CI -0.37, -0.17], pemotional affect while the n-6: n-3 ratio is detrimental to positive affect. PMID:27188896

  11. Effect of two bleaching agents on enamel morphology: a SEM study

    Ghavam M.

    2005-05-01

    Full Text Available Statement of Problem: Bleaching materials are able to change the surface morphology as well as mineral and organic content of tooth structure. Considering that bleaching is done for aesthetic purpose, awareness of the possible effect of these materials on hard tissue is important, because it may affect the restorative treatments. Purpose: The aim of this study was comparing the effect of two bleaching materials, Kimia and Ultradent both containing 35% H2O2, on tooth enamel by SEM. Materials and Methods: Five intact central incisors were cut into three sections vertically and each part was randomly divided into three groups. Group 1 (control, without any bleaching. Group 2, bleached with Kimia 35% H2O2. Group 3, bleached with Ultradent 35% H2O2. Each tooth served as its own control. Then the samples were observed by SEM with 250 and 500 magnifications. Results: In the control group some scratches and small white grains were observed which seems to be the result of mastication trauma and pumice powder. In the other groups, morphologic changes like increased surface roughness, deepening of cracks, rod exposure and presence of new cracks were observed. The two experimental materials did not differ in these regards. Conclusion: It seems that both studied materials have limited destructive effects on tooth enamel which seems to be of no clinical importance.

  12. Coral bleaching on high-latitude marginal reefs at Sodwana Bay, South Africa

    Coral bleaching, involving the expulsion of symbiotic zooxanthellae from the host cells, poses a major threat to coral reefs throughout their distributional range. The role of temperature in coral bleaching has been extensively investigated and is widely accepted. A bleaching event was observed on the marginal high-latitude reefs of South Africa located at Sodwana Bay during the summer months of 2000. This was associated with increased sea temperatures with high seasonal peaks in summer and increased radiation in exceptionally clear water. The bleaching was limited to Two-mile Reef and Nine-mile Reef at Sodwana Bay and affected -1 from May 1994 to April 2000. High maximum temperatures were measured (>29 deg. C). The lowest mean monthly and the mean maximum monthly temperatures at which coral bleaching occurred were 27.5 and 28.8 deg. C, respectively, while the duration for which high temperatures occurred in 2000 was 67 days at ≥27.5 deg. C (4 days at ≥28.8 deg. C). Increased water clarity and radiation appeared to be a synergistic cause in the coral bleaching encountered at Sodwana Bay

  13. Effect of postoperative bleaching on microleakage of etch-and-rinse and self-etch adhesives

    Vajihesadat Mortazavi

    2011-01-01

    Full Text Available Background: Bleaching the discoloured teeth may affect the tooth/composite interface. The aim of this in vitro experimental study was to evaluate the effect of vital tooth bleaching on microleakage of existent class V composite resin restorations bonded with three dental bonding agents. Methods : Class V cavities were prepared on buccal surfaces of 72 intact, extracted human anterior teeth with gingival margins in dentin and occlusal margins in enamel, and randomly divided into 3 groups. Cavities in the three groups were treated with Scotch bond Multi-Purpose, a total etch system and Prompt L-Pop and iBond, two self-etch adhesives. All teeth were restored with Z250 resin composite material and thermo-cycled. Each group was equally divided into the control and the bleached subgroups (n = 12. The bleached subgroups were bleached with 15% carbamide peroxide gel for 8 hours a day for 15 days. Microleakage scores were evaluated on the incisal and cervical walls. Data were analyzed using Kruskal-Wallis, Mann-Whitney and Bonferroni post-hoc tests (α = 0.05. Results: Bleaching with carbamide peroxide gel significantly increased the microleakage of composite restorations in Prompt L-Pop group at dentinal walls (P = 0.001. Bleaching had no effect on microleakage of restorations in the Scotch bond Multi-Purpose and iBond groups. Conclusion: Vital tooth bleaching with carbamide peroxide gel has an adverse effect on marginal seal of dentinal walls of existent composite resin restorations bonded with prompt L-Pop self-etch adhesive.

  14. The effect of remin pro and MI paste plus on bleached enamel surface roughness.

    Haleh Heshmat

    2014-04-01

    Full Text Available The growing demand for enhanced esthetic appearance has led to great developments in bleaching products. The exposure of hard tissues of the tooth to bleaching agents can affect the roughness of the enamel surface. The freshly bleached enamel surface exposed to various surface treatments such as fluoride and other remineralizing agents have been assessed in this study. The aim of this experimental study was to compare the effect of Casein Phosphopeptide-Amorphous Calcium Phosphate with Fluoride (MI Paste Plus and Remin Pro on the enamel surface roughness after bleaching.Thirty enamel samples of sound human permanent molars were prepared for this study. After initial roughness measurement with profilometer, the samples were exposed to 37% carbamide peroxide bleaching agent 20 minutes twice, and randomly divided into three groups of ten. In group 1, a CPP-ACPF containing paste (MI Paste Plus and in group 2, Remin Pro were applied to the teeth during a 15 day period for 5 minutes, twice a day. Samples of group 3 (control were immersed in artificial saliva for 15 days. The roughness of all samples were measured at the beginning, after bleaching and after the study intervention and statistically analyzed.The surface roughness significantly increased in all groups following bleaching, and then it showed a decrease after application of both Remin Pro and CPP-ACPF in comparison to using bleaching agent (P0.05.There was no difference between surface roughness of MI Paste Plus and Remin Pro groups. Also the surface roughness was decreased compared to the initial enamel surface roughness.

  15. Coral bleaching under unconventional scenarios of climate warming and ocean acidification

    Kwiatkowski, Lester; Cox, Peter; Halloran, Paul R.; Mumby, Peter J.; Wiltshire, Andy J.

    2015-08-01

    Elevated sea surface temperatures have been shown to cause mass coral bleaching. Widespread bleaching, affecting >90% of global coral reefs and causing coral degradation, has been projected to occur by 2050 under all climate forcing pathways adopted by the IPCC for use within the Fifth Assessment Report. These pathways include an extremely ambitious pathway aimed to limit global mean temperature rise to 2 °C (ref. ; Representative Concentration Pathway 2.6--RCP2.6), which assumes full participation in emissions reductions by all countries, and even the possibility of negative emissions. The conclusions drawn from this body of work, which applied widely used algorithms to estimate coral bleaching, are that we must either accept that the loss of a large percentage of the world’s coral reefs is inevitable, or consider technological solutions to buy those reefs time until atmospheric CO2 concentrations can be reduced. Here we analyse the potential for geoengineering, through stratospheric aerosol-based solar radiation management (SRM), to reduce the extent of global coral bleaching relative to ambitious climate mitigation. Exploring the common criticism of geoengineering--that ocean acidification and its impacts will continue unabated--we focus on the sensitivity of results to the aragonite saturation state dependence of bleaching. We do not, however, address the additional detrimental impacts of ocean acidification on processes such as coral calcification that will further determine the benefit to corals of any SRM-based scenario. Despite the sensitivity of thermal bleaching thresholds to ocean acidification being uncertain, stabilizing radiative forcing at 2020 levels through SRM reduces the risk of global bleaching relative to RCP2.6 under all acidification-bleaching relationships analysed.

  16. Surviving coral bleaching events: porites growth anomalies on the Great Barrier Reef.

    Neal E Cantin

    Full Text Available Mass coral bleaching affected large parts of the Great Barrier Reef (GBR in 1998 and 2002. In this study, we assessed if signatures of these major thermal stress events were recorded in the growth characteristics of massive Porites colonies. In 2005 a suite of short (<50 cm cores were collected from apparently healthy, surviving Porites colonies, from reefs in the central GBR (18-19°S that have documented observations of widespread bleaching. Sites included inshore (Nelly Bay, Pandora Reef, annually affected by freshwater flood events, midshelf (Rib Reef, only occasionally affected by freshwater floods and offshore (Myrmidon Reef locations primarily exposed to open ocean conditions. Annual growth characteristics (extension, density and calcification were measured in 144 cores from 79 coral colonies and analysed over the common 24-year period, 1980-2003. Visual examination of the annual density bands revealed growth hiatuses associated with the bleaching years in the form of abrupt decreases in annual linear extension rates, high density stress bands and partial mortality. The 1998 mass-bleaching event reduced Porites calcification by 13 and 18% on the two inshore locations for 4 years, followed by recovery to baseline calcification rates in 2002. Evidence of partial mortality was apparent in 10% of the offshore colonies in 2002; however no significant effects of the bleaching events were evident in the calcification rates at the mid shelf and offshore sites. These results highlight the spatial variation of mass bleaching events and that all reef locations within the GBR were not equally stressed by the 1998 and 2002 mass bleaching events, as some models tend to suggest, which enabled recovery of calcification on the GBR within 4 years. The dynamics in annual calcification rates and recovery displayed here should be used to improve model outputs that project how coral calcification will respond to ongoing warming of the tropical oceans.

  17. ALKALINE PEROXIDE BLEACHING OF HOT WATER TREATED WHEAT STRAW

    Suvi Mustajoki

    2010-05-01

    Full Text Available The aim of this study was to evaluate the possibilities for chemical consumption reduction in P-P-Paa-P bleaching (P alkaline peroxide stage, Paa peracetic stage of hot water treated straw and the effect of the wheat straw variability on the process. Papermaking fibre production from wheat straw using such a process could be implemented on a small scale if chemical consumption was low enough to eliminate the need for chemical recovery. The pulp properties obtained with this process are equal to or even superior to the properties of wheat straw soda pulp. The possibility of enhancing the first peroxide stage with oxygen and pressure was studied. The possibility for substitution of sodium hydroxide partially with sodium carbonate was also investigated. The objective was to achieve International Standardization Organization (ISO brightness of 75%, with minimal sodium hydroxide consumption, whilst maintaining the pulp properties. The optimization of the peroxide bleaching is challenging if the final brightness target cannot be reduced. Results indicate that up to 25% of the sodium hydroxide could be substituted with sodium carbonate without losing brightness or affecting pulp properties. Another possibility is a mild alkali treatment between the hot water treatment and the bleaching sequence.

  18. Modeling Reef Hydrodynamics to Predict Coral Bleaching

    Bird, James; Steinberg, Craig; Hardy, Tom

    2005-11-01

    The aim of this study is to use environmental physics to predict water temperatures around and within coral reefs. Anomalously warm water is the leading cause for mass coral bleaching; thus a clearer understanding of the oceanographic mechanisms that control reef water temperatures will enable better reef management. In March 1998 a major coral bleaching event occurred at Scott Reef, a 40 km-wide lagoon 300 km off the northwest coast of Australia. Meteorological and coral cover observations were collected before, during, and after the event. In this study, two hydrodynamic models are applied to Scott Reef and validated against oceanographic data collected between March and June 2003. The models are then used to hindcast the reef hydrodynamics that led up to the 1998 bleaching event. Results show a positive correlation between poorly mixed regions and bleaching severity.

  19. Thermoluminescence dating of partially bleached sediments

    A major problem in TL dating of sediments is the lack of knowledge concerning the degree of bleaching that took place during transport of the material prior to deposition. A method is proposed that may enable partially bleached sediments to be dated by determining the correct residual value to be used with the build-up curve. The method uses a combination of results for quartz and feldspar, presuming that these two minerals have the same age. Samples are bleached by sunlight for different periods, and the correct bleaching time is taken as that producing residual values which yield identical ages for the minerals. Preliminary results for a number of aeolian sediments from Jutland are presented. In most cases the TL ages were in acceptable agreement with expected ages. (author)

  20. Ocean acidification has no effect on thermal bleaching in the coral Seriatopora caliendrum

    Wall, C. B.; Fan, T.-Y.; Edmunds, P. J.

    2014-03-01

    The objective of this study was to test whether elevated pCO2 predicted for the year 2100 (85.1 Pa) affects bleaching in the coral Seriatopora caliendrum (Ehrenberg 1834) either independently or interactively with high temperature (30.5 °C). Response variables detected the sequence of events associated with the onset of bleaching: reduction in the photosynthetic performance of symbionts as measured by maximum photochemical efficiency ( F v/ F m) and effective photochemical efficiency (Δ F/ F m') of PSII, declines in net photosynthesis ( P net) and photosynthetic efficiency (alpha, α), and finally, reduced chlorophyll a and symbiont concentrations. S. caliendrum was collected from Nanwan Bay, Taiwan, and subjected to combinations of temperature (27.7 vs. 30.5 °C) and pCO2 (45.1 vs. 85.1 Pa) for 14 days. High temperature reduced values of all dependent variables (i.e., bleaching occurred), but high pCO2 did not affect Symbiodinium photophysiology or productivity, and did not cause bleaching. These results suggest that short-term exposure to 81.5 Pa pCO2, alone and in combination with elevated temperature, does not cause or affect coral bleaching.

  1. Fatty acid composition of camelina sativa as affected by combined nitrogen and sulphur fertilisation

    Šípalová, Markéta; Lošák, Tomáš; Hlušek, Jaroslav; Vollmann, Johann; Hudec, Jozef; Filipčík, Radek; Macek, Michal; Kráčmar, Stanislav

    2011-01-01

    Camelina (false flax) oil is an important source of linolenic acid (C18:3). As agronomic treatments such as fertilization may affect seed quality parameters in oilseeds, fatty acid composition and oil content of Camelina sativa were investigated as affected by the combined application of nitrogen and sulphur in pot experiments. Nitrogen was applied as NH4NO3 at rates of 0.6 (N1), 0.9 (N2) or 1.2 (N3) g per pot. To increase the natural soil S-SO42- level of 25 mg/kg (S0) to 35 mg/kg (S1), 45 m...

  2. Fermentation Conditions that Affect Clavulanic Acid Production in Streptomyces clavuligerus: A Systematic Review

    Ser, Hooi-Leng; Law, Jodi Woan-Fei; Chaiyakunapruk, Nathorn; Jacob, Sabrina Anne; Palanisamy, Uma Devi; Chan, Kok-Gan; Goh, Bey-Hing; Lee, Learn-Han

    2016-01-01

    The β-lactamase inhibitor, clavulanic acid is frequently used in combination with β-lactam antibiotics to treat a wide spectrum of infectious diseases. Clavulanic acid prevents drug resistance by pathogens against these β-lactam antibiotics by preventing the degradation of the β-lactam ring, thus ensuring eradication of these harmful microorganisms from the host. This systematic review provides an overview on the fermentation conditions that affect the production of clavulanic acid in the firstly described producer, Streptomyces clavuligerus. A thorough search was conducted using predefined terms in several electronic databases (PubMed, Medline, ScienceDirect, EBSCO), from database inception to June 30th 2015. Studies must involve wild-type Streptomyces clavuligerus, and full texts needed to be available. A total of 29 eligible articles were identified. Based on the literature, several factors were identified that could affect the production of clavulanic acid in S. clavuligerus. The addition of glycerol or other vegetable oils (e.g., olive oil, corn oil) could potentially affect clavulanic acid production. Furthermore, some amino acids such as arginine and ornithine, could serve as potential precursors to increase clavulanic acid yield. The comparison of different fermentation systems revealed that fed-batch fermentation yields higher amounts of clavulanic acid as compared to batch fermentation, probably due to the maintenance of substrates and constant monitoring of certain entities (such as pH, oxygen availability, etc.). Overall, these findings provide vital knowledge and insight that could assist media optimization and fermentation design for clavulanic acid production in S. clavuligerus. PMID:27148211

  3. Fermentation Conditions that Affect Clavulanic Acid Production in Streptomyces clavuligerus: A Systematic Review.

    Ser, Hooi-Leng; Law, Jodi Woan-Fei; Chaiyakunapruk, Nathorn; Jacob, Sabrina Anne; Palanisamy, Uma Devi; Chan, Kok-Gan; Goh, Bey-Hing; Lee, Learn-Han

    2016-01-01

    The β-lactamase inhibitor, clavulanic acid is frequently used in combination with β-lactam antibiotics to treat a wide spectrum of infectious diseases. Clavulanic acid prevents drug resistance by pathogens against these β-lactam antibiotics by preventing the degradation of the β-lactam ring, thus ensuring eradication of these harmful microorganisms from the host. This systematic review provides an overview on the fermentation conditions that affect the production of clavulanic acid in the firstly described producer, Streptomyces clavuligerus. A thorough search was conducted using predefined terms in several electronic databases (PubMed, Medline, ScienceDirect, EBSCO), from database inception to June 30th 2015. Studies must involve wild-type Streptomyces clavuligerus, and full texts needed to be available. A total of 29 eligible articles were identified. Based on the literature, several factors were identified that could affect the production of clavulanic acid in S. clavuligerus. The addition of glycerol or other vegetable oils (e.g., olive oil, corn oil) could potentially affect clavulanic acid production. Furthermore, some amino acids such as arginine and ornithine, could serve as potential precursors to increase clavulanic acid yield. The comparison of different fermentation systems revealed that fed-batch fermentation yields higher amounts of clavulanic acid as compared to batch fermentation, probably due to the maintenance of substrates and constant monitoring of certain entities (such as pH, oxygen availability, etc.). Overall, these findings provide vital knowledge and insight that could assist media optimization and fermentation design for clavulanic acid production in S. clavuligerus. PMID:27148211

  4. Local Stressors Reduce Coral Resilience to Bleaching

    Carilli, Jessica E; Norris, Richard D.; Black, Bryan A.; Walsh, Sheila M.; McField, Melanie

    2009-01-01

    Coral bleaching, during which corals lose their symbiotic dinoflagellates, typically corresponds with periods of intense heat stress, and appears to be increasing in frequency and geographic extent as the climate warms. A fundamental question in coral reef ecology is whether chronic local stress reduces coral resistance and resilience from episodic stress such as bleaching, or alternatively promotes acclimatization, potentially increasing resistance and resilience. Here we show that following...

  5. HOME BLEACHING TECHNIQUE USING CARBAMIDE PEROXIDE

    Rahmi Alma Farah Adang

    2015-06-01

    Full Text Available There are two basic kinds of tooth whitening agents. The first is over the counter materials and the other is material used by the dentist or under dentist control. Home bleaching is a technique using 10% carbamide peroxide on a tray applied by patient under dentist supervision. This paper is a review of the effect of 10% carbamide peroxide home bleaching technique. It is revealed that this method is simple, safe, economic, and has short chairside time.

  6. Melanin bleaching with dilute hydrogen peroxide: a simple and rapid method.

    Liu, Chia-Hsing; Lin, Chih-Hung; Tsai, Min-Jan; Chen, Wan-Tzu; Chai, Chee-Yin; Huang, Ya-Chun; Tsai, Kun-Bow

    2013-05-01

    Melanins are naturally occurring pigments in both normal and pathologic tissues. Two common bleaching processes are potassium permanganate followed by oxalic acid treatment and dilute hydrogen peroxide (H2O2) process. The potassium permanganate/oxalic acid method is faster and more easily incorporated in conventional daily immunostaining protocols, whereas the dilute H2O2 method requires 24 hours. This study aimed to reduce melanin bleaching time by using a 10% H2O2 dilution. First, reaction time was reduced to 30 minutes by raising the temperature to 65°C. Second, containers with high thermal conductivity were used to improve bleaching effectiveness. Experimental comparisons of melanin treatments with H2O2 contained in an iron jar, a glass coplin jar, and a plastic steel jar obtained bleaching time of 20, 30, and 40 minutes, respectively. These modifications of the conventional bleaching method significantly improve the speed and efficiency of the procedure and are recommended when performing immunohistochemical studies. PMID:23060296

  7. OZONE BLEACHING AT NEUTRAL PH – A NEW CONCEPT

    Fernando Carvalho; Denis Asbahr; Antonio A. R. Godoy; Jorge Luiz Colodette

    2010-01-01

    The effect of medium consistency ozone stage pH was evaluated for brown and oxygen delignified eucalyptus kraft pulp samples obtained from VCP - Luiz Antônio pulp mill. These samples were used as such or previously treated with the hot acid stage (A). The main objective of this study was to determine the viability of increasing the ozone stage pH aiming at decreasing bleaching variable costs. The ozone stage was studied in the pH range of 2.5-9.0, taking into account some important variables ...

  8. ECF BLEACHING WITH A FINAL HYDROGEN PEROXIDE STAGE: IMPACT ON THE CHEMICAL COMPOSITION OF Eucalyptus globulus KRAFT PULPS

    Pedro E. G. Loureiro

    2010-11-01

    Full Text Available Two industrial elemental chlorine free (ECF bleaching sequences, D0(EOPD1(EPD2 and OQ(PODP, are compared with respect to the bulk content of lignin, carboxyl, hexeneuronic acids (HexA, and reducing groups after each bleaching stage. HexA groups contribute significantly to the total content of carboxyl groups, and their degradation during chlorine dioxide bleaching is reflected by a decrease of the carboxyl content. The higher degradation using an enhanced use of oxygen-based bleaching chemicals is associated with a higher fiber charge reduction, mainly due to xylan depletion. Additionally, the effect of process variables of a laboratory final hydrogen peroxide stage on the chemical composition of the fully bleached pulp (D0(EOPD1P and OQ(PODP is studied. The ability of final peroxide bleaching to raise the content of carboxyl groups is dependent on the operating conditions and pulp bleaching history. A balance between carbohydrate oxidation and dissolution of oxidized groups determines the effect on fiber charge. The effect of hydrogen peroxide stabilizers added into the final stage on the content of carboxyl groups is also reported.

  9. Metal cycling during sediment early diagenesis in a water reservoir affected by acid mine drainage

    Torres, Ester; Ayora, Carlos; Canovas, C. R.;

    2013-01-01

    The discharge of acid mine drainage (AMD) into a reservoir may seriously affect the water quality. To investigate the metal transfer between the water and the sediment, three cores were collected from the Sancho Reservoir (Iberian Pyrite Belt, SW Spain) during different seasons: turnover event...

  10. Characterization of napthenic acids in oil sands process-affected waters using fluorescence technology

    Brown, L.; Alostaz, M.; Ulrich, A. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering

    2009-07-01

    Process-affected water from oil sands production plants presents a major environmental challenge to oil sands operators due to its toxicity to different organisms as well as its corrosiveness in refinery units. This abstract investigated the use of fluorescence excitation-emission matrices to detect and characterize changes in naphthenic acid in oil sands process-affected waters. Samples from oil sands production plants and storage ponds were tested. The study showed that oil sands naphthenic acids show characteristic fluorescence signatures when excited by ultraviolet light in the range of 260 to 350 mm. The signal was a unique attribute of the naphthenic acid molecule. Changes in the fluorescence signature can be used to determine chemical changes such as degradation or aging. It was concluded that the technology can be used as a non-invasive continuous water quality monitoring tool to increase process control in oil sands processing plants.

  11. Diatoms as biomonitors in two temporary streams affected by acid drainage from disused mines

    Diatoms are increasingly used as biomonitors of water quality in Australia, partly as an extension of the AUSRIVAS concept and partly through the increasing emphasis on biological/ecological monitoring of stream health that is acknowledged in the Australian and New Zealand water quality guidelines (ANZECC and ARMCANZ, 2000). This work brings together the findings of three studies relating diatom populations to the water chemistry of two temporary streams affected by acid drainage. In the three studies reported, changes in the benthic diatom flora have been successfully used to: show the toxic effects of acid drainage from two mine sites; differentiate between nutrient and acid drainage pollution in a stream system affected by more than one pollutant and provide independent corroboration of the AQUARISK ecological risk assessment code

  12. Characterization of napthenic acids in oil sands process-affected waters using fluorescence technology

    Process-affected water from oil sands production plants presents a major environmental challenge to oil sands operators due to its toxicity to different organisms as well as its corrosiveness in refinery units. This abstract investigated the use of fluorescence excitation-emission matrices to detect and characterize changes in naphthenic acid in oil sands process-affected waters. Samples from oil sands production plants and storage ponds were tested. The study showed that oil sands naphthenic acids show characteristic fluorescence signatures when excited by ultraviolet light in the range of 260 to 350 mm. The signal was a unique attribute of the naphthenic acid molecule. Changes in the fluorescence signature can be used to determine chemical changes such as degradation or aging. It was concluded that the technology can be used as a non-invasive continuous water quality monitoring tool to increase process control in oil sands processing plants

  13. Assessment of the process of cottonseed oil bleaching in hexane

    Megahed, Ola A.

    2002-12-01

    Full Text Available This work has been initiated to assess the feasibility of bleaching cottonseed oil in miscella as a processing step next to alkali refining in miscella. Alkali refining of cottonseed oil in miscella has several advantages over conventional refining technologies with respect to oil quality, oil losses and process cost. Therefore, the process efficiency of the bleaching of cottonseed oil in presence of hexane (at a volumetric ratio of 1:1, has been studied and compared to that without solvent. The process efficiency has been evaluated according to the decolourization capacity, the oil losses on spent earth, the filtration rate of the oil from the clay and the acidity of the bleached oil as well as its peroxide content. The bleaching in presence of hexane was carried out at 25ºC whereas that by conventional bleaching at 110ºC. Different clay loads were used in each of the two bleaching techniques and the colour indices of the oils before and after bleaching determined in each case. The results were used to predict Freundlich adsorption equations for the oil pigments in both cases. These equations were then used to predict the colour of the oils obtained by bleaching of refined oils of different grades. The results have shown that oil decolourization is more efficient in presence of solvent when the starting oil is of an acceptable grade and the reverse is true for low grade oils. Also, the possibility of oil oxidation during bleaching is less in presence of solvent. Moreover, the bleaching in miscella has proved two other additional advantages over conventional bleaching. The filtration of oil from clay is much faster in miscella bleaching and the oil losses on spent earth is lower. This will be reflected on the overall process economy.Este trabajo ha sido iniciado para evaluar la viabilidad de la decoloración del aceite de semilla de algodón en miscela como un paso de procesado próximo a la refinación alcalina en miscela. La refinaci

  14. Broiler skin color as affected by organic acids: influence of concentration and method of application.

    Bilgili, S F; Conner, D E; Pinion, J L; Tamblyn, K C

    1998-05-01

    Color of broiler skin was evaluated after exposure to organic acids under various concentrations and simulated potential plant application conditions. Breast skin from chilled broiler carcasses was treated with acetic (AA), citric (CA), lactic (LA), malic (ML), mandelic (MN), propionic (PA), or tartaric (TA) acids at 0.5, 1, 2, 4, and 6% concentrations. Each acid and concentration was applied in simulated dip (23 C for 15 s), scalder (50 C for 2 min), and immersion chiller (1 C for 60 min) conditions. A tap water control was included with each application method. Objective color values of L* (lightness), a* (redness), and b* (yellowness) were measured before and after the treatments to calculate color differentials under a factorial arrangement of organic acids and concentrations. Skin lightness increased (P dip and scalder applications. Skin redness was reduced significantly in scalder, and yellowness in dip and scalder applications, respectively. In simulated dip application, with the exception of PA, all acids decreased lightness and increased redness and yellowness values. Propionic acid had little affect on lightness and redness values, but decreased yellowness values. In simulated scalder application, with the exception of PA, all acids decreased lightness with increasing concentration. The redness values changed little in scalder application. However, yellowness values were increased with all acids, except for PA, which decreased yellowness values. In simulated chiller conditions, all acids, except for PA, decreased lightness and redness and increased yellowness values. Propionic acid increased lightness and decreased yellowness values significantly in chiller conditions. Alterations in skin color should be taken into account in the selection and application of organic acids as carcass disinfectants. PMID:9603365

  15. Recycling of bleach plant filtrates by electrodialysis removal of inorganic non-process elements.; TOPICAL

    Water use in the pulp and paper industry is very significant, and the U.S. pulp and paper industries as well as other processing industries are actively pursuing water conservation and pollution prevention by in-process recycling of water. Bleach plant effluent is a large portion of the water discharged from a typical bleached kraft pulp mill. The recycling of bleach plant effluents to the kraft recovery cycle is widely regarded as an approach to low effluent bleached kraft pulp production. The focus of this work has been on developing an electrodialysis process for recycling the acidic bleach plant effluent of bleached Kraft pulp mills. Electrodialysis is uniquely suited as a selective kidney to remove non-process elements (NPEs) from bleach plant effluent before they reach the chemical recovery cycle. Using electrodialysis for selective NPE removal can prevent the problems caused by accumulation of inorganic NPEs in the pulping cycle and recovery boiler. In this work, acidic bleach plant filtrates from three mills using different bleaching sequences based on chlorine dioxide were characterized. The analyses showed no fundamental differences in the inorganic NPE composition or other characteristics among these filtrates. The majority of total dissolved solids in the effluents were found to be inorganic NPEs. Chloride and nitrate were present at significant levels in all effluent samples. Sodium was the predominant metal ion, while calcium and magnesium were also present at considerable levels. The feasibility of using electrodialysis to selectively remove inorganic NPEs from the acidic bleach effluent was successfully demonstrated in laboratory experiments with effluents from all these three mills. Although there were some variations in these effluents, chloride and potentially harmful cations, such as potassium, calcium, and magnesium, were removed efficiently from the bleach effluents into a small-volume, concentrated purge stream. This effective removal of

  16. OVERVIEW OF IN-OFFICE BLEACHING OF VITAL TEETH

    Hegde Mithra N.

    2012-11-01

    Full Text Available The importance of tooth whitening for patients has shown a dramatic increase in the number of products and procedures over recent years. Vital tooth bleaching refers to chair-side clinical application of a chemical solution to a tooth surface in order to achieve whitening effect of the teeth. Vital bleaching have found to be very effective but they also have their the drawbacks. The current article gives knowledge of vital tooth whitening with respect to external bleaching methods. the external bleaching of vital teeth focuses on patient selection, mechanisms, bleaching procedure and various in-office bleaching systems and techniques and their disadvantages.

  17. Impact of mass coral bleaching on reef fish community and fishermen catches at Sabang, Aceh Province, Indonesia

    Edi Rudi; Taufiq Iskandar; Nur Fadli; Hidayati Hidayati

    2012-01-01

    Mass coral bleaching was observed at Sabang, Aceh in early 2010, and approximately 60% ofhard coral in waters surrounding Sabang died post-event. Coral mortality was expected to affect thecomposition of reef fish due to decrease its function such as providing a shelter, feeding and spawninggrounds for fish and other marine organisms. The objectives of this research were to evaluate the impactof coral bleaching on coral reef fish community and to compare the composition of fishermen catchesbef...

  18. Omega-3 fatty acids in the gravid pig uterus as affected by maternal supplementation with omega-3 fatty acids.

    Brazle, A E; Johnson, B J; Webel, S K; Rathbun, T J; Davis, D L

    2009-03-01

    Two experiments evaluated the ability of maternal fatty acid supplementation to alter conceptus and endometrial fatty acid composition. In Exp. 1, treatments were 1) the control, a corn-soybean meal diet; 2) flax, the control diet plus ground flax (3.75% of diet); and 3) protected fatty acids (PFA), the control plus a protected fish oil source rich in n-3 PUFA (Gromega, JBS United Inc., Sheridan, IN; 1.5% of diet). Supplements replaced equal parts of corn and soybean meal. When gilts reached 170 d of age, PG600 (PMSG and hCG, Intervet USA, Millsboro, DE) was injected to induce puberty, and dietary treatments (n = 8/treatment) were initiated. When detected in estrus, gilts were artificially inseminated. On d 40 to 43 of gestation, 7 gilts in the control treatment, 8 gilts in the PFA treatment, and 5 gilts in the flax treatment were pregnant and were slaughtered. Compared with the control treatment, the flax treatment tended to increase eicosapentaenoic acid (EPA: C20:5n-3) in fetuses (0.14 vs. 0.25 +/- 0.03 mg/g of dry tissue; P = 0.055), whereas gilts receiving PFA had more (P flax and PFA diets increased (P flax, and PFA diet, respectively) in the chorioallantois. In the endometrium, EPA and docosapentaenoic acid (C22:5n-3) were increased by the flax diet (P flax diet selectively increased EPA, and the PFA diet selectively increased DHA in the fetus and endometrium. In Exp. 2, gilts were fed diets containing PFA (1.5%) or a control diet beginning at approximately 170 of age (n = 13/treatment). A blood sample was collected after 30 d of treatment, and gilts were artificially inseminated when they were approximately 205 d old. Conceptus and endometrial samples were collected on d 11 to 19 of pregnancy. Plasma samples indicated that PFA increased (P breeding, affected endometrial, conceptus, and fetal fatty acid composition in early pregnancy. Dynamic day effects in fatty acid composition indicate this may be a critical period for maternal fatty acid resources to

  19. Effectiveness of home bleaching agents in discolored teeth and influence on enamel microhardness

    Carina Sinclér Delfino

    2009-08-01

    Full Text Available OBJECTIVES: This study evaluated the effectiveness of different home bleaching agents on color alteration and their influence on surface and subsurface microhardness of discolored bovine enamel. MATERIAL AND METHODS: Forty-five fragments of bovine incisors were randomly allocated into 3 groups (n=15 according to the bleaching agent: 10% carbamide peroxide gel (CP10, 16% carbamide peroxide gel (CP16 and 6.5%-hydrogen-peroxide-based strip (HP6.5. Before bleaching treatment, initial values of Knoop surface microhardness and color (CIEL*a*b* were obtained and the fragments were artificially stained in hemolyzed rat blood. Then, bleaching treatments were performed over a 21-day period. Color changes (ΔE were assessed at 7, 14 and 21 days, and final surface microhardness reading was done after 21 days. Thereafter, the fragments were bisected to obtain subsurface microhardness. Data were subjected to ANOVA and Tukey's tests (α=5%. RESULTS: Color changes produced by CP16 were similar to those of CP10, and the color changes produced by these materials were significantly superior to those produced by HP6.5. Color changes at 21 days were superior to 7 days and similar to 14 days. The time did not influence color changes for CP16, which showed similarity between the 14- and 21-day results. No statistically significant differences were found among the home bleaching agents for surface and subsurface microhardness. CONCLUSIONS: Microhardness of bovine enamel was not affected by the bleaching agents. The 16% carbamide peroxide gel was the most effective for bleaching the stained substrate.

  20. Coral bleaching on high-latitude marginal reefs at Sodwana Bay, South Africa

    Celliers, Louis; Schleyer, Michael H

    2002-12-01

    Coral bleaching, involving the expulsion of symbiotic zooxanthellae from the host cells, poses a major threat to coral reefs throughout their distributional range. The role of temperature in coral bleaching has been extensively investigated and is widely accepted. A bleaching event was observed on the marginal high-latitude reefs of South Africa located at Sodwana Bay during the summer months of 2000. This was associated with increased sea temperatures with high seasonal peaks in summer and increased radiation in exceptionally clear water. The bleaching was limited to Two-mile Reef and Nine-mile Reef at Sodwana Bay and affected <12% of the total living cover on Two-mile Reef. Montipora spp., Alveopora spongiosa and Acropora spp. were bleached, as well as some Alcyoniidae (Sinularia dura, Lobophytum depressum, L. patulum). A cyclical increase in sea temperature (with a period of 5-6 years) was recorded during 1998-2000 in addition to the regional temperature increase caused by the El Nino Southern Oscillation phenomenon. The mean sea temperature increased at a rate of 0.27 deg. C year{sup -1} from May 1994 to April 2000. High maximum temperatures were measured (>29 deg. C). The lowest mean monthly and the mean maximum monthly temperatures at which coral bleaching occurred were 27.5 and 28.8 deg. C, respectively, while the duration for which high temperatures occurred in 2000 was 67 days at {>=}27.5 deg. C (4 days at {>=}28.8 deg. C). Increased water clarity and radiation appeared to be a synergistic cause in the coral bleaching encountered at Sodwana Bay.

  1. Evaluation of peanut hulls as an alternative to bleaching clays

    Hassanein, M. M. M.

    2011-09-01

    Full Text Available Peanut hulls (PNH were carbonized at different temperatures, times, and evaluated at different concentrations as an alternative to bleaching clays. Evaluation of bleached crude soybean oil with PNH was based on their delta free fatty acids, reduction in peroxide value (PV, reduction in phospholipids (PL and bleachability. The performance of several commercially used bleaching clays was evaluated, for comparison. Mixtures were formulated including: PNH and Tonsil -N (TN, PNH and Fuller’s earth (FE and PNH and O-passive (OP and examined. The oxidative stability of oils was determined. Results for the investigated commercial bleaching clays revealed: TN > FE > F > TF > OP. Highest reduction in PV and PL, and highest bleachability were achieved for soybean oil bleached with 2% PNH carbonized at 500°C for 30 min (PNH”. Mixtures of PNH” with the three chosen bleaching clays indicated that 1PNH”: 2TN gave the highest bleachability. CSO was miscella bleached in hexane using PNH” and resulted in an appreciable improvement in all oil characteristics, especially in bleachability. Oxidative stability of oils was in the following order: TN > control > FE > PNH” with Induction period values of 23,1 > 6,43 > 5,73 > 2,85 h, respectively.

    Las cáscaras de maní (PNH fueron carbonizadas a diferentes temperaturas y tiempos, y utilizadas a diferentes concentraciones como una alternativa a las tierras decolorantes. La evaluación de un aceite de soja decolorado con PNH se ha basado en sus ácidos grasos libres, reducción del índice de peróxidos (PV, reducción de los fosfolípidos (PL, y en la blanqueabilidad. El rendimiento de varias tierras decolorantes de uso comercial fue evaluado y comparado con el de PNH carbonizada. Las mezclas formuladas incluían: PNH y Tonsil-N (TN, PNH y tierras de Fuller (FE y PNH y O-pasivo (OP. La estabilidad oxidativa de los aceites resultantes fue determinada. Los resultados revelaron que la efectividad de la

  2. Coupling of hydrologic transport and chemical reactions in a stream affected by acid mine drainage

    Kimball, B.A.; Broshears, R.E.; Bencala, K.E.; McKnight, Diane M.

    1994-01-01

    Experiments in St. Kevin Gulch, an acid mine drainage stream, examined the coupling of hydrologic transport to chemical reactions affecting metal concentrations. Injection of LiCl as a conservative tracer was used to determine discharge and residence time along a 1497-m reach. Transport of metals downstream from inflows of acidic, metal-rich water was evaluated based on synoptic samples of metal concentrations and the hydrologic characteristics of the stream. Transport of SO4 and Mn was generally conservative, but in the subreaches most affected by acidic inflows, transport was reactive. Both 0.1-??m filtered and particulate Fe were reactive over most of the stream reach. Filtered Al partitioned to the particulate phase in response to high instream concentrations. Simulations that accounted for the removal of SO4, Mn, Fe, and Al with first-order reactions reproduced the steady-state profiles. The calculated rate constants for net removal used in the simulations embody several processes that occur on a stream-reach scale. The comparison between rates of hydrologie transport and chemical reactions indicates that reactions are only important over short distances in the stream near the acidic inflows, where reactions occur on a comparable time scale with hydrologic transport and thus affect metal concentrations.

  3. Erosion and abrasion on dental structures undergoing at-home bleaching

    Tarquinio SBC

    2011-07-01

    Full Text Available Flávio Fernando Demarco1, Sônia Saeger Meireles2, Hugo Ramalho Sarmento1, Raquel Venâncio Fernandes Dantas1, Tatiana Botero3, Sandra Beatriz Chaves Tarquinio11Graduate Program in Dentistry, School of Dentistry, Federal University of Pelotas, Brazil; 2Department of Operative Dentistry, Federal University of Paraíba, Brazil; 3Cariology, Restorative Science, and Endodontics Department, School of Dentistry, University of Michigan, MI, USAAbstract: This review investigates erosion and abrasion in dental structures undergoing at-home bleaching. Dental erosion is a multifactorial condition that may be idiopathic or caused by a known acid source. Some bleaching agents have a pH lower than the critical level, which can cause changes in the enamel mineral content. Investigations have shown that at-home tooth bleaching with low concentrations of hydrogen or carbamide peroxide have no significant damaging effects on enamel and dentin surface properties. Most studies where erosion was observed were in vitro. Even though the treatment may cause side effects like sensitivity and gingival irritation, these usually disappear at the end of treatment. Considering the literature reviewed, we conclude that tooth bleaching agents based on hydrogen or carbamide peroxide have no clinically significant influence on enamel/dentin mineral loss caused by erosion or abrasion. Furthermore, the treatment is tolerable and safe, and any adverse effects can be easily reversed and controlled.Keywords: peroxide, tooth bleaching, enamel, dentin, erosion, abrasion

  4. Influence of microhybrid resin and etching times on bleached enamel for the bonding of ceramic brackets

    Leily Macedo Firoozmand

    2013-04-01

    Full Text Available The aim of this study was to evaluate the shear bond strength (SBS of polycrystalline ceramic brackets (PCB bonded after bleaching treatment using different composite resins and enamel etching times. A total of 144 bovine incisors were randomly divided into two study groups (n = 72, each as follows: G1, enamel bleached with 35% hydrogen peroxide, and G2 (control group, enamel unbleached. After the bleaching treatment, the samples were stored in artificial saliva for 14 days. These groups were further divided into two subgroups (n = 36, each as follows: GA, brackets bonded with Transbond XT (3M and GB, brackets bonded with Filtek Z250 (3M. For each resin used, three different etching times with 37% phosphoric acid (15, 30 and 60 seconds were tested. SBS tests were performed using a universal testing machine (EMIC, and the adhesive remnant index (ARI score was verified. Significant differences among the three experimental conditions and interactions between the groups were observed. The type of composite resin accounted for 24% of the influence on the bond strength, whereas the etching time and bleaching treatment accounted for 14.5% and 10% of the influence on bond strength, respectively. The ARI revealed that the most common area of adhesion failure was at the composite resin-bracket interface. The type of composite resin, etching time and external bleaching significantly influenced the SBS of PCB on enamel, even after 14 days of saliva storage.

  5. APPLIED STUDY OF BIRCH PULP BLEACHING USING DIMETHYLDIOXIRANE TO OBTAIN ACETATE-GRADE PULP

    Shu-Ke Zhou

    2010-06-01

    Full Text Available As a pulp bleaching agent, dimethyldioxirane (DMD is effective and selective. In this study, it was employed as a delignifying agent or as an activating agent for hydrogen peroxide treatment in bleaching acetate-grade pulp. Brightness, kappa number, degree of polymerization (DP, and alpha-cellulose content were evaluated to determine the optimal charges of DMD: 2.5% AO, and 4% HSO5-, respectively. Results from the totally chlorine-free (TCF sequences MEQMPA, MEpQMPA, and OQMPA suggested that DMD is both effective and selective as a delignifying agent but not as a brightening agent as compared to oxygen. And in a long sequence for the bleaching of dissolving pulp, acid treatment can be used in two approaches: to remove the metal ions without washing before the chelation stage, and to reduce hemicellulose and ash in the final stage.

  6. Ultrasound aided in situ transesterification of crude palm oil adsorbed on spent bleaching clay

    Boey, Peng-Lim [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Ganesan, Shangeetha, E-mail: shangeetha.ganesan@gmail.co [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Maniam, Gaanty Pragas [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Ali, Dafaalla Mohamed Hag [School of Chemical Sciences, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Chemistry Department, Sudan University of Science and Technology, P.O. Box 407, Khartoum (Sudan)

    2011-05-15

    Research highlights: {yields} Crude palm oil adsorbed on spent bleaching clay converted to biodiesel. {yields} Ultrasound dislodges adsorbed oil from spent bleaching clay into reaction mixture. {yields} Co-solvents promotes miscibility of the reactants. -- Abstract: Adsorbed crude palm oil on spent bleaching clay (SBC) was in situ transesterified to methyl esters (biodiesel) by the aid of ultrasound and organic co-solvents (petroleum ether (PE) or ethyl methyl ketone (EMK)). The SBC under study was found to contain 24.2-27.0% of crude oil with free fatty acids (FFA) of 3.01% and moisture content of 0.29%. The optimized reaction conditions were as follows: methanol to oil molar ratio of 150:1; catalyst (KOH), 20%; reaction temperature, 60 {+-} 2 {sup o}C; reaction time, 2 h. Using PE as a co-solvent, highest conversion of 75.2% was achieved while 60% was recorded with EMK.

  7. The effects of bleach plant effluent recycle in kraft mill green liquors

    Richardson, B.M.; Uloth, V.C. [Pulp and Paper Research Inst. of Canada, Vancouver, BC (Canada); Dorris, G.M. [Pulp and Paper Research Inst. of Canada, Pointe Claire, PQ (Canada); Stafford, E. C.

    1995-12-31

    A new approach to reducing or eliminating effluent flows from a kraft mill through process changes and by recycling, was presented. A closed system experiment was conducted in which bleach plant effluents and green liquors were used to simulate effluent recycling to the recausticizing area in place of fresh water. Results showed that with current levels of water use, acid effluents from bleaching of softwood pulp could be recycled to the recausticizing area if a 5-18 per cent loss in causticizing efficiency and a 10 per cent decrease in the lime mud settling rate was tolerable. High levels of sodium chloride did not always reduce causticizing efficiency. It was found that bleach plant water usage was very high in the plants studied. New ways to minimize water use in the plant must be found if a significant degree of closure is to be achieved. 15 refs., 6 tabs., 8 figs.

  8. Ultrasound aided in situ transesterification of crude palm oil adsorbed on spent bleaching clay

    Research highlights: → Crude palm oil adsorbed on spent bleaching clay converted to biodiesel. → Ultrasound dislodges adsorbed oil from spent bleaching clay into reaction mixture. → Co-solvents promotes miscibility of the reactants. -- Abstract: Adsorbed crude palm oil on spent bleaching clay (SBC) was in situ transesterified to methyl esters (biodiesel) by the aid of ultrasound and organic co-solvents (petroleum ether (PE) or ethyl methyl ketone (EMK)). The SBC under study was found to contain 24.2-27.0% of crude oil with free fatty acids (FFA) of 3.01% and moisture content of 0.29%. The optimized reaction conditions were as follows: methanol to oil molar ratio of 150:1; catalyst (KOH), 20%; reaction temperature, 60 ± 2 oC; reaction time, 2 h. Using PE as a co-solvent, highest conversion of 75.2% was achieved while 60% was recorded with EMK.

  9. Lamb meat quality and intramuscular fatty acid composition as affected by concentrates including different legume seeds

    Pietro Pennisi

    2011-04-01

    Full Text Available The aim of the experiment was to study the effect of concentrates including legume seeds (Vicia faba var. minor or Pisum sativum on lamb performances and on meat quality, with an emphasis on intramuscular fatty acid composition. Thirty lambs (14.5 ± 3.45 kg live weight were randomly assigned to three dietary treatments: PEA group (concentrate including 400 g/kg of peas; FB group (concentrate including 380 g/kg of faba bean; SBM group (concentrate including 180 g/kg of soybean meal. Growth and slaughter performances were not affected by treatments as well as physical and proximate chemical meat characteristics. FB and SBM meat showed higher (P<0.001 vaccenic acid levels compared to PEA meat. Oleic acid was higher (P<0.05 in PEA meat compared to SBM meat while its level in FB meat was similar to counterparts. Linoleic acid levels tended to increase (P<0.10 in SBM lambs compared to PEA animals. PEA group showed higher (P<0.001 α-linolenic acid proportions compared to FB and SBM groups and a tendentially higher (P<0.10 eicosapentaenoic acid content compared to SBM meat. As a result, total n-3 fatty acids were higher (P<0.05 in PEA meat compared to SBM one while the proportions in FB meat were at intermediate level. These findings accounted for a lower and more favourable (P<0.001 n-6/n-3 ratio in PEA group compared to counterparts. Peas based-concentrate seemed to be more effective than faba bean- or soybean meal-included concentrates to improve the acidic profile of meat leading to higher α-linolenic acid levels and a lower n-6/n-3 ratio.

  10. Maternal dietary Alpine butter intake affects human milk: fatty acids and conjugated linoleic acid isomers.

    Bertschi, Isabelle; Collomb, Marius; Rist, Lukas; Eberhard, Pius; Sieber, Robert; Bütikofer, Ulrich; Wechsler, Daniel; Folkers, Gerd; von Mandach, Ursula

    2005-06-01

    Consumption of CLA by lactating women affects the composition of their milk, but the pattern of the different CLA isomers is still unknown. We determined the effects of short maternal supplementation with CLA-rich Alpine butter on the occurrence of FA and CLA isomers in human milk. In an open randomized controlled study with a two-period cross-over design, milk FA and CLA isomer concentrations were measured on postpartum days > or = 20 in two parallel groups of lactating women before, during, and after consumption of defined quantities of Alpine butter or margarine with comparable fat content (10 d of butter followed by 10 d of margarine for one group, and vice versa in the other). In the 16 women who completed the study (8/group), Alpine butter supplementation increased the C16 and C18 FA, the sum of saturated FA, the 18:1 trans FA, and the trans FA with CLA. The CLA isomer 18:2 c9,t11 increased by 49.7%. Significant increases were also found for the isomers t9,t11, t7,c9, t11,c13, and t8,c10 18:2. The remaining nine of the total 14 detectable isomers showed no changes, and concentrations were <5 mg/100 g fat. A breastfeeding mother can therefore modulate the FA/CLA supply of her child by consuming Alpine butter. Further studies will show whether human milk containing this FA and CLA isomer pattern acts as a functional food for newborns. PMID:16149737

  11. Local stressors reduce coral resilience to bleaching.

    Jessica E Carilli

    Full Text Available Coral bleaching, during which corals lose their symbiotic dinoflagellates, typically corresponds with periods of intense heat stress, and appears to be increasing in frequency and geographic extent as the climate warms. A fundamental question in coral reef ecology is whether chronic local stress reduces coral resistance and resilience from episodic stress such as bleaching, or alternatively promotes acclimatization, potentially increasing resistance and resilience. Here we show that following a major bleaching event, Montastraea faveolata coral growth rates at sites with higher local anthropogenic stressors remained suppressed for at least 8 years, while coral growth rates at sites with lower stress recovered in 2-3 years. Instead of promoting acclimatization, our data indicate that background stress reduces coral fitness and resilience to episodic events. We also suggest that reducing chronic stress through local coral reef management efforts may increase coral resilience to global climate change.

  12. Cone photopigment bleaching abnormalities in diabetes.

    Elsner, A E; Burns, S A; Lobes, L A; Doft, B H

    1987-04-01

    We have used a color-matching technique to obtain estimates of the optical density of cone photopigments as a function of retinal illuminance in patients with insulin-dependent diabetes mellitus (IDDM). We found that the half-bleach illuminance of some patients is abnormally high. That is, it takes more light to bleach an equivalent amount of photopigment in these patients. Since low illuminance color matches for these patients are normal, this implies that these patients have normal amounts of photopigment, but the photopigment is not bleaching normally. This result clearly points to abnormalities in the outer retina of these diabetic patients. The most likely causes of this abnormality are either decreases in the ability of the cones to absorb light, or an increased rate of regeneration of the cone photopigments. PMID:3557875

  13. Lactobacillus acidophilus NCFM affects vitamin E acetate metabolism and intestinal bile acid signature in monocolonized mice

    Roager, Henrik Munch; Sulek, Karolina; Skov, Kasper;

    2014-01-01

    deconjugation and dehydroxylation of bile acids. Furthermore, we confirmed that carbohydrate metabolism is affected by NCFM in the mouse intestine. Especially, the digestion of larger carbohydrates (penta- and tetrasaccharides) was increased in MC mice. Interestingly, we also found vitamin E (α......-tocopherol acetate) in higher levels in the intestine of GF mice compared to MC mice, suggesting that NCFM either metabolizes the compound orindirectly affects the absorption by changing the metabolome in the intestine. The use of NCFM to increase the uptake of vitamin E supplements in humans and animals is a highly...

  14. Comparative study of lipophilic extractives of hardwoods and corresponding ECF bleached kraft pulps

    Pascoal Neto, C.

    2006-07-01

    Full Text Available The lipophilic extractives of Eucalyptus globulus , Eucalyptus grandis , Eucalyptus urograndis , Betula verrucosa and Acacia mangium woods and of the corresponding ECF bleached kraft pulps, were characterised by GC-MS. The five hardwoods showed significant differences in the content and composition of the main families of extractives, namely fatty acids, long chain aliphatic alcohols and sterols. Significant differences in the composition persist after wood pulping and ECF bleaching of pulps. The fate of the various types of extractives during the wood and pulp processing is discussed. Long chain aliphatic acids and alcohols are quite stable during the pulp production and are retained to a great extent in the final bleached pulp; delta 5 sterols are mostly oxidised and partially retained in the pulps, while delta 7 sterols are completely degraded and/or dissolved. B. verrucosa and A. mangium bleached pulps show contents of fatty acids about 4 and 20 times higher than that of Eucalyptus pulps, respectively, while the content of long chain aliphatic alcohols in A. mangium pulp is of the order of 100 times higher than Eucalyptus and B. verrucosa pulps.

  15. Surviving Coral Bleaching Events: Porites Growth Anomalies on the Great Barrier Reef

    Cantin, Neal E.; Lough, Janice M.

    2014-01-01

    Mass coral bleaching affected large parts of the Great Barrier Reef (GBR) in 1998 and 2002. In this study, we assessed if signatures of these major thermal stress events were recorded in the growth characteristics of massive Porites colonies. In 2005 a suite of short (

  16. Study of thermal annealing induced plasmonic bleaching in Ag:TiO2 nanocomposite thin films

    Graphical abstract: The plasmonic bleaching observed in Ag:TiO2 nanocomposite thin films, when annealed at 450 °C in Ar environment, is due to the dissociation of Ag nanoparticles followed by diffusion of Ag atoms outside the nanocomposite film and into substrate. - Plasmonic properties of metal nanomaterials critically affect on thermal treatments. One of such effects is ‘plasmonic-bleaching’ observed in ‘atom beam co-sputtering’ derived Ag:TiO2 nanocomposite thin films, when annealed at 450 °C. The origin of bleaching is investigated using glancing angle X-ray diffraction and Rutherford backscattering spectroscopy. The kinetics of Ag nanoparticles during the deposition and after thermal treatment is presented to understand involved host-matrix interactions. Based on Rutherford Materials Program simulation, possible mechanism of bleaching is presented

  17. Exogenous abscisic acid significantly affects proteome in tea plant (Camellia sinensis) exposed to drought stress

    Lin Zhou; Hui Xu; Sue Mischke; Meinhardt, Lyndel W.; Dapeng Zhang; Xujun Zhu; Xinghui Li; Wanping Fang

    2014-01-01

    Tea [Camellia sinensis (L.) O. Kuntze] is an important economic crop, and drought is the most important abiotic stress affecting yield and quality. Abscisic acid (ABA) is an important phytohormone responsible for activating drought resistance. Increased understanding of ABA effects on tea plant under drought stress is essential to develop drought-tolerant tea genotypes, along with crop management practices that can mitigate drought stress. The objective of the present investigation is evaluat...

  18. Copper complexation by fulvic acid affects copper toxicity to the larvae of the polychaete

    Qiu, Jian-Wen; Tang, Xiao; Zheng, Chuanbo; Li, Yan; Huang, Yanliang

    2007-01-01

    Copper complexation by fulvic acid affects copper toxicity to the larvae of the polychaete Hydroides elegans correspondence: Corresponding author. Tel.: +852 34117055; fax: +852 34115995. (Qiu, Jian-Wen) (Qiu, Jian-Wen) Department of Biology, Hong Kong Baptist University - HONG KONG, CHINA (Qiu, Jian-Wen) CHINA (Qiu, Jian-Wen) Department of Biology, Hong Kong Baptist University - HONG KONG, CHINA (Tang, Xiao) Insti...

  19. Sediment-water interaction in a water reservoir affected by acid mine drainage : experimental and modeling

    Torres Sánchez, Ester

    2013-01-01

    The discharge of acid mine drainage into a water reservoir may seriously affect the water quality. In this setting, sediment is commonly thought to act as a sink for pollutants. However, redox oscillations in the bottom water promoted by stratification-turnover events may significantly alter the metal cycling. A new sequential extraction procedure has been developed to study the metal partitioning in the sediment. The new scheme for iron, sulfur and organic carbon rich sediments was evaluated...

  20. The Effects of Habitat on Coral Bleaching Responses in Kenya

    Grimsditch, Gabriel; Mwaura, Jelvas M.; Kilonzo, Joseph; Amiyo, Nassir

    2010-01-01

    This study examines the bleaching responses of scleractinian corals at four sites in Kenya (Kanamai, Vipingo, Mombasa and Nyali) representing two distinct lagoon habitats (relatively shallow and relatively deep). Bleaching incidence was monitored for the whole coral community, while zooxanthellae densities and chlorophyll levels were monitored for target species (Pocillopora damicornis, Porites lutea, and Porites cylindrica) during a non-bleaching year (2006) and a year of mild-bleaching (200...

  1. Photo-bleaching response in chlorophyll solutions

    Photo-excitation processes were investigated in chlorophyll solutions by irradiation with UV light sources. Photo-excited bulk effects during the bleaching experiments were diagnosed. The optical diagnostic was expressed by a Beer-Lambert matrix formulation and applied to the experimental results. The chromophores evaluated optical cross-section was 10-15 cm2 and the optical absorption coefficient dynamic variation was fitted to a simple reaction rate model. The bleaching rates were expressed by this model and fitted to the experimental data

  2. Meat fatty acid composition as affected by fatness and genetic factors: a review

    De Smet, Stefaan; Raes, Katleen; Demeyer, Daniel

    2004-01-01

    Influence des facteurs génétiques et de l'état d'engraissement sur la composition en acides gras de la viande. Revue. La composition en acides gras de la viande est affectée par divers facteurs : des facteurs nutritionnels, mais aussi des facteurs génétiques, quoiqu'à un degré moindre. L'espèce animale est également une source de variation importante, c'est même la plus importante. La viande des ruminants est plus riche en acides gras saturés que celle des monogastriques, en raison de la bioh...

  3. Soil acidity as affecting micronutrients concentration, nitrato reductase enzyme activity and yield in upland rice plants

    Edemar Moro

    2013-12-01

    Full Text Available The lowest grain yield of rice under no-tillage system (NTS in relation to the conventional system may be due to the predominance nitrate in the soil and the low nitrate reductase activity. Another reason may be caused by micronutrient deficiency because of superficially soil acidity corrections. Therefore, the objective of this study was to evaluate the changes caused by soil pH in the N forms in the soil, micronutrients concentration in rice plants, nitrate reductase activity, yield of rice and its components. The experiment was performed in a greenhouse conditions. The experimental design was a completely randomized in a factorial three (levels of soil acidity x five (micronutrients sources with four replications. The addition of micronutrients does not affect levels of nitrate and ammonium in the soil; soil acidity significantly affects levels of nitrate and ammonium in the soil, concentration of micronutrients in rice plants and crop yield and its components; medium soil acidity (pH 5.5 result in medium to high levels of Cu and Fe, medium level of Zn and Mn, high nitrate reductase activity, resulting in higher dry matter, tillers, panicles, spikelets, weight of 100 grains and hence grain yield.

  4. 21 CFR 872.6475 - Heat source for bleaching teeth.

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Heat source for bleaching teeth. 872.6475 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6475 Heat source for bleaching teeth. (a) Identification. A heat source for bleaching teeth is an AC-powered device that consists of...

  5. Bleaching and diffusion dynamics in optofluidic dye lasers

    Gersborg-Hansen, Morten; Balslev, Søren; Mortensen, Asger;

    2007-01-01

    The authors have investigated the bleaching dynamics that occur in optofluidic dye lasers where the liquid laser dye in a microfluidic channel is locally bleached due to optical pumping. They find that for microfluidic devices, the dye bleaching may be compensated through diffusion of dye molecules...... pumping devices. ©2007 American Institute of Physics....

  6. Lactobacillus acidophilus NCFM affects vitamin E acetate metabolism and intestinal bile acid signature in monocolonized mice.

    Roager, Henrik M; Sulek, Karolina; Skov, Kasper; Frandsen, Henrik L; Smedsgaard, Jørn; Wilcks, Andrea; Skov, Thomas H; Villas-Boas, Silas G; Licht, Tine R

    2014-01-01

    Monocolonization of germ-free (GF) mice enables the study of specific bacterial species in vivo. Lactobacillus acidophilus NCFM(TM) (NCFM) is a probiotic strain; however, many of the mechanisms behind its health-promoting effect remain unknown. Here, we studied the effects of NCFM on the metabolome of jejunum, cecum, and colon of NCFM monocolonized (MC) and GF mice using liquid chromatography coupled to mass-spectrometry (LC-MS). The study adds to existing evidence that NCFM in vivo affects the bile acid signature of mice, in particular by deconjugation. Furthermore, we confirmed that carbohydrate metabolism is affected by NCFM in the mouse intestine as especially the digestion of oligosaccharides (penta- and tetrasaccharides) was increased in MC mice. Additionally, levels of α-tocopherol acetate (vitamin E acetate) were higher in the intestine of GF mice than in MC mice, suggesting that NCFM affects the vitamin E acetate metabolism. NCFM did not digest vitamin E acetate in vitro, suggesting that direct bacterial metabolism was not the cause of the altered metabolome in vivo. Taken together, our results suggest that NCFM affects intestinal carbohydrate metabolism, bile acid metabolism and vitamin E metabolism, although it remains to be investigated whether this effect is unique to NCFM. PMID:24717228

  7. Fenomena Bleaching Karang Tahun 2009 di Pulau Badi Selat Makassar (Coral Bleaching Event on 2009 in Badi Island Makassar Strait)

    Yusuf, Syafyudin; Rani, Chair; Jompa, Jamaluddin

    2010-01-01

    Bleaching event is loss of zooxanthella from the marine organisms tissue, as a caused by enviromental stress. Coral bleaching fenomenom was observed on May and June 2009 in Badi Island on Makassar Strait, Indonesia . The method used in this study is identified the photos coral colonies which bleaching infected were photographed with a Ixus Digital Canon 75 camera in an underwater housing. The results showed that the bleaching corals are caused by temperature anomaly above 1,24oC higher...

  8. Factors affecting the fatty acid composition and fat oxidative stability in pigs

    Karel Vehovsky

    2015-03-01

    Full Text Available The aim of the study was to evaluate the effect of selected factors affecting fatty acids (FA composition in pig fat. In the experiment, the influence of nutrition, gender, carcass weight, lean meat proportion (LMP and intramuscular fat (IMF were monitored. The effect of diet, specifically the influence of added linseed or corn on the fatty acids composition in the backfat was studied in pigs. From the perspective of the required increase of polyunsaturated fatty acids (PUFA only the addition of the linseed proved to have a significant effect. Another evaluated aspect concerning the FA spectrum was the gender. While the backfat in barrows showed higher (P≤0.05 amount of monounsaturated fatty acids (MUFA, the backfat in gilts displayed a significantly higher proportion (P≤0.01 of the PUFA and total unsaturated fatty acids (UFA. A significant effect on the PUFA proportion has also been demonstrated for the lean meat proportion (LMP parameter, which therefore represents not only a qualitative carcass meat parameter but also plays an important role in relation to the FA composition in the fat in pigs. In connection to the FA proportion changes the study also monitored the fat oxidative stability with the use of the TBARS method. Concerning the oxidative stability the effects of nutrition, FA groups, gender, carcass weight and LMP were studied. The relationship between the above mentioned factors and oxidative stability was found to be insignificant.

  9. Identifying well-bleached quartz using the different bleaching rates of quartz and feldspar luminescence signals

    Murray, A.S.; Thomsen, Kristina Jørkov; Masuda, N.; Buylaert, Jan-Pieter; Jain, Mayank

    2012-01-01

    relative bleaching rates of quartz optically stimulated luminescence (OSL) and feldspar luminescence stimulated at 50 °C by infrared light (IR50) and feldspar luminescence stimulated at 290 °C by infrared light after a stimulation at 50 °C (pIRIR290), and use recently deposited samples to determine the......When dating older sedimentary deposits using quartz, there are no unambiguous methods for identifying the presence of incomplete bleaching. Current statistical analysis of dose distributions depends entirely on the assumption that incomplete bleaching and mixing are the main causes of any excess...... dispersion in the distribution; the only existing way to test this assumption is using independent age control. Here we suggest a new approach to this question, based on the differential bleaching rates of quartz and feldspar luminescence signals. We first present data that confirm the differences in...

  10. Low environmental impact bleaching sequences for attaining high brightness level with eucalyptus SPP pulp

    M. M. Costa

    2009-03-01

    Full Text Available The alternatives used for minimizing the usage of chlorine dioxide in bleaching sequences included a hot acid hydrolysis (Ahot stage, the use of hot chlorine dioxide (Dhot and ozone stages at medium consistency and high consistency (Zmc and Zhc, in addition to stages with atmospheric hydrogen peroxide (P and pressurized hydrogen peroxide (PO. The results were interpreted based on the cost of the chemical products, bleaching process yields and on minimizing the environmental impact of the bleaching process. In spite of some process restrictions, high ISO brightness levels were kept around 90 % brightness. Additionally, the inclusion of stages like acid hydrolysis, pressurized peroxide and ozone in the bleaching sequences provided an increase in operating flexibility, aimed at reducing environmental impact (ECF Light. The Dhot(EOPD(PO sequence presented lower operating cost for ISO brightness above 92 %. However, this kind of sequence was not allowed for closing the wastewater circuit, even partially. For ISO brightness level around 91%, the AhotZhcDP sequence presented a lower operating cost than the others.

  11. Oxidation of rapeseed oil in waste activated bleaching earth and its effect on riboflavin production in culture of Ashbya gossypii.

    Park, Enoch Y; Ming, Hwa

    2004-01-01

    Long-term behavior of rapeseed oil in waste activated bleaching earth (ABE) and the effect of this oil on riboflavin production in the culture of Ashbya gossypii were investigated. Waste ABE with 40% (w/w) rapeseed oil was stored for 80 d, and the extent of oxidation of rapeseed oil was measured by several analytical methods to determine the chemical properties of the oil at different stages of the oil deterioration process:peroxide value, acid value, concentrations of organic acids, acetaldehyde and unsaturated fatty acid, and content of polymerized triglycerides. Peroxide value, acid value, and concentrations of organic acids and acetaldehyde did not affect riboflavin production. However, the content of polymerized triglycerides markedly increased the viscosity of rapeseed oil and was the main reason for the exponential decrease in riboflavin production. A good correlation between the polymerized triglyceride content or viscosity and riboflavin production in the culture of A. gossypii using rapeseed oil as the sole carbon source was found. PMID:16233590

  12. Improved sensitivity, safety and laboratory turnaround time in the diagnosis of pulmonary tuberculosis by use of bleach sedimentation

    Ameh James

    2015-05-01

    Full Text Available Background: Inadequate diagnostic processes and human resources in laboratories contribute to a high burden of tuberculosis (TB in low- and middle-income countries. Direct smear microscopy is relied on for TB diagnosis; however, sensitivity rates vary. To improve sensitivity of direct microscopy, the researchers employed several approaches, including sputum digestion and concentration of acid-fast bacilli (AFB, a technique which uses commercial bleach.Objectives: This study compared methods used to diagnose active Mycobacterium tuberculosis infections.Methods: Three sputum specimens were collected from each of 340 participants in Abuja, Nigeria, over two consecutive days. Direct microscopy was performed on all specimens; following microscopy, one specimen from each patient was selected randomly for bleach sedimentation and one for Lowenstein-Jensen culture.Results: Direct microscopy produced 28.8% AFB-positive results, whilst bleach sedimentation resulted in 30.3%. When compared with the cultures, 26.5% were AFB true positive using direct microscopy and 27.1% using bleach sedimentation. Whilst the specificity rate between these two methods was not statistically significant (P = 0.548, the sensitivity rate was significant (P = 0.004.Conclusion: Based on these results, bleach increases the sensitivity of microscopy compared with direct smear and has similar specificity. When diagnosing new cases of pulmonary TB, one bleach-digested smear is as sensitive as three direct smears, reducing waiting times for patients and ensuring the safety of laboratory technicians.

  13. Modelling the optical bleaching of a complex TL signal

    Thermoluminescence (TL) intensity decrease is observed in many materials after optical stimulation and is called optical bleaching of TL. The optical bleaching of a TL peak does not always mean that the traps responsible for this peak are emptied by stimulating light. The McKeever model explains TL bleaching by the emptying of deep thermally disconnected traps. The modification of this model is used for simulating the optical bleaching of complex TL curves in the case of complex TL spectrum. Some characteristic outcomes important for interpreting the results of TL optical bleaching measurements are reported

  14. Enamel alteration following tooth bleaching and remineralization.

    Coceska, Emilija; Gjorgievska, Elizabeta; Coleman, Nichola J; Gabric, Dragana; Slipper, Ian J; Stevanovic, Marija; Nicholson, John W

    2016-06-01

    The purpose of this study was to compare the effects of professional tooth whitening agents containing highly concentrated hydrogen peroxide (with and without laser activation), on the enamel surface; and the potential of four different toothpastes to remineralize any alterations. The study was performed on 50 human molars, divided in two groups: treated with Opalescence(®) Boost and Mirawhite(®) Laser Bleaching. Furthermore, each group was divided into five subgroups, a control one and 4 subgroups remineralized with: Mirasensitive(®) hap+, Mirawhite(®) Gelleѐ, GC Tooth Mousse™ and Mirafluor(®) C. The samples were analysed by SEM/3D-SEM-micrographs, SEM/EDX-qualitative analysis and SEM/EDX-semiquantitative analysis. The microphotographs show that both types of bleaching cause alterations: emphasized perikymata, erosions, loss of interprizmatic substance; the laser treatment is more aggressive and loss of integrity of the enamel is determined by shearing off the enamel rods. In all samples undergoing remineralization deposits were observed, those of toothpastes based on calcium phosphate technologies seem to merge with each other and cover almost the entire surface of the enamel. Loss of integrity and minerals were detected only in the line-scans of the sample remineralized with GC Tooth Mousse™. The semiquantitative EDX analysis of individual elements in the surface layer of the enamel indicates that during tooth-bleaching with HP statistically significant loss of Na and Mg occurs, whereas the bleaching in combination with a laser leads to statistically significant loss of Ca and P. The results undoubtedly confirm that teeth whitening procedures lead to enamel alterations. In this context, it must be noted that laser bleaching is more aggressive for dental substances. However, these changes are reversible and can be repaired by application of remineralization toothpastes. PMID:27197087

  15. Identification of Chlorinated Fatty Acids in Standard Samples and Fish Lipids : Verification and Validation of Extraction, Transesterification and GC-MS/XSD

    Brown, Philip; Järlskog, Ida

    2015-01-01

    Chlorine gas bleaching was a common method used in pulp industries. As a consequence, significant amounts of chlorine were discharged into surrounding aquatic ecosystems, affecting the biota. Chlorinated organic pollutants are formed when chlorine react with organic material. Octadecanoic acid (stearic acid) is one of the most common saturated fatty acids in aquatic biota. In a naturally occurring process two and four chlorine atoms, respectively, are added over the unsaturated bonds, forming...

  16. Bonding Effectiveness of Universal Adhesive to Intracoronal Bleached Dentin Treated with Sodium Ascorbate.

    Trindade, Thaís Fantinato; Moura, Luana Kelle Batista; Raucci, Walter; Messias, Danielle Cristine Furtado; Colucci, Vivian

    2016-01-01

    This study evaluated the effect of restorative protocol with sodium ascorbate on the shear bond strength (SBS) of a universal adhesive to intracoronal bleached dentin. One hundred-and-twenty bovine dentin fragments were randomly divided into 12 groups (n=10), according to the bleaching procedure (unbleached and bleached) and restorative protocol (no treatment, 10% sodium ascorbate -10SA, 35% sodium ascorbate -35SA and two-step etch-and-rinse -ER or one-step self-etch -SE Scotchbond universal adhesive approaches). Four whitening sessions were performed using 35% hydrogen peroxide. The samples from control groups were kept in relative humidity at 37 °C. Immediately after bleaching procedures, the assigned antioxidant solution was applied on dentin and restorative procedures were performed following either the ER or the SE approach. After 24 h, the specimens were subjected to SBS test. Data (MPa) were analyzed by ANOVA and Tukey's test (?=0.05). Lower SBS values were found for bleached specimens (8.54 MPa) compared with those unbleached (12.13 MPa) (pbond strength of the sodium ascorbate-treated groups was higher than those untreated, regardless of the strategy employed (pbond strength values for both ER (8.32 MPa) and SE (8.28 MPa) adhesive strategies. The group treated with 10SA submitted to ER approach (10.14 MPa) was similar to untreated groups (p>0.05). It may be concluded that bond strength of composite resin to intracoronal dentin was affected by restorative protocol and reduced by bleaching. PMID:27224564

  17. N-3 polyunsaturated fatty acid DHA during IVM affected oocyte developmental competence in cattle.

    Oseikria, Mouhamad; Elis, Sébastien; Maillard, Virginie; Corbin, Emilie; Uzbekova, Svetlana

    2016-06-01

    The positive effect of n-3 polyunsaturated fatty acids (FAs) on fertility in ruminants seems to be partly mediated through direct effects on the oocyte developmental potential. We aimed to investigate whether supplementation with physiological levels of docosahexaenoic acid (DHA, C22:6 n-3 polyunsaturated fatty acids) during IVM has an effect on oocyte maturation and in vitro embryo development in cattle. We reported that DHA (0, 1, 10, or 100 μM) had no effect on oocyte viability or maturation rate after 22-hour IVM. Incubation of oocyte-cumulus complexes with 1-μM DHA during IVM significantly increased (P reaction, negative effects of 100-μM DHA were associated with significant increase of progesterone synthesis by oocyte-cumulus complexes, a three-fold increase in expression level of FA transporter CD36 and a two-fold decrease of FA synthase FASN genes in cumulus cells (CCs) of corresponding oocytes. Docosahexaenoic acid at 1 and 10 μM had no effect on expression of those and other key lipid metabolism-related genes in CC. In conclusion, administration of a low physiological dose of DHA (1 μM) during IVM may have beneficial effects on oocyte developmental competence in vitro without affecting lipid metabolism gene expression in surrounding CCs, contrarily to 100 μM DHA which diminished oocyte quality associated with perturbation of lipid and steroid metabolism in CC. PMID:26898414

  18. Accumulation of aluminium and iron by bryophytes in streams affected by acid-mine drainage

    Engleman, C.J.; McDiffett, W.F. [Bucknell University, Lewisburg, PA (United States). Dept. of Biology

    1996-12-31

    This paper examines the accumulation of two heavy metals (Al and Fe) by bryophytes in a northern Pennsylvania stream system affected by acid-mine drainage. Four sites within one watershed were selected on the basis of their pH and dissolved metal concentrations. Significant differences among sites were found with regard to bioaccumulation of Al an Fe. A negative relationship between pH and Fe concentrations in bryophyte tissues was found, with the highest accumulation of Fe observed at the most acidic site (pH 3.5), whereas accumulation of Al was highest at a site with an intermediate pH of 5.2. Bryophytes transplanted from a circum-neutral site to acidic sites showed highly significant increases in Fe and Al concentrations in tissues after 6 weeks, and transplants from more acidic sites to a circum-neutral site generally showed highly significant declines in Fe and Al concentration in tissues after the incubation period.

  19. Factors that affect the degradation of naphthenic acids in oil sands wastewater by indigenous microbial communities

    The acute toxicity of wastewater generated during the extraction of bitumen from oil sands is believed to be due to naphthenic acids (NAs). To determine the factors that affect the rate of degradation of representative NAs in microcosms containing wastewater and the acute toxicity of treated and untreated wastewater, the effects of temperature, dissolved oxygen concentration, and phosphate addition on the rate of 14CO2 release form two representative naphthenic acid substrates, (linear) U-14C-palmitic acid (PA) and (bicyclic) decahydro-2-naphthoic acid-8-14C (DHNA), were monitored. Tailings pond water (TPW) contained microorganisms well adapted to mineralizing both PA and DHNA:PA was degraded more quickly (10--15% in 4 weeks) compared to DHNA (2--4% in 8 weeks). On addition of phosphate, the rate of NA degradation increased up to twofold in the first 4 weeks, with a concurrent increase in the rate of oxygen consumption by oil sands TPW. The degradation rate then declined to levels equivalent to those measured in flasks without phosphate. The observed plateau was not due to phosphate limitation. Decreases in either the dissolved oxygen concentration or the temperature reduced the rate. Phosphate addition also significantly decreased the acute toxicity of TPW to fathead minnows. In contrast, Microtox reg-sign analyses showed no reduction in the toxicity of treated or untreated TPW after incubation for up to 8 weeks at 15 C

  20. Impact of mass coral bleaching on reef fish community and fishermen catches at Sabang, Aceh Province, Indonesia

    Edi Rudi

    2012-12-01

    Full Text Available Mass coral bleaching was observed at Sabang, Aceh in early 2010, and approximately 60% ofhard coral in waters surrounding Sabang died post-event. Coral mortality was expected to affect thecomposition of reef fish due to decrease its function such as providing a shelter, feeding and spawninggrounds for fish and other marine organisms. The objectives of this research were to evaluate the impactof coral bleaching on coral reef fish community and to compare the composition of fishermen catchesbefore and after the coral bleaching. The data were collected before (in 2008 and after (in 2010 themass coral bleaching event in Sabang waters by using a photographic method and the data on theaverage catch of fishermen (catch per fishing effort was calculated in kg/hour. The data of theknowledge of fishermen on climate change was collected by questionnaire method. The results showedthat 259 species of coral reef fishes were caught by fishermen in 2008 and 2010. There was nosignificantly difference between the fish catches before and after the mass coral bleaching. However,species richness decreased up to 50% after the mass coral bleaching. The knowledge of fishermen onclimate change issue was very low.

  1. Seychelles Lagoon Provides Corals with a Refuge from Bleaching

    An extensive bleaching event in the summer of the year 1997-1998 affected most reefs along East Africa's shores. In the aftermath of that episode, the reefs of Ile Alphonse in the Seychelles were examined and it was found that reefs along the seaward slopes of the island lost >95% of their branching coral colonies, with considerably higher survival of massive species. Ile Alphonse features a nearly circular shallow lagoon, with steep seaward slopes. Contrary to our expectations, mortality in the warmer lagoon was far lower than of coral colonies on the surrounding slopes, bathed in deeper and cooler waters. We suggest that corals in the lagoon were protected from UV radiation by leachate stemming from sea grass leaves steeped in the lagoon. Our measurements in the lagoon showed a strong attenuation of ultraviolet radiation, no observed in the waters outside the lagoon, and laboratory examination confirmed that the strong UV absorption of substances leached into seawater from decomposing leaves of the sea grass Thalassodendron (=Cymodocea) testudinaceum. Our findings demonstrate the synergism between elevated seawater temperature and UV radiation in triggering bleaching on shallow reefs.

  2. Seychelles Lagoon Provides Corals with a Refuge from Bleaching

    Zvy Dubinsky

    2008-06-01

    Full Text Available An extensive bleaching event in the summer of the year 1997-1998 affected most reefs along East Africa's shores. In the aftermath of that episode, the reefs of Île Alphonse in the Seychelles were examined and it was found that reefs along the seaward slopes of the island lost >95% of their branching coral colonies, with considerably higher survival of massive species. Île Alphonse features a nearly circular shallow lagoon, with steep seaward slopes. Contrary to our expectations, mortality in the warmer lagoon was far lower than of coral colonies on the surrounding slopes, bathed in deeper and cooler waters. We suggest that corals in the lagoon were protected from UV radiation by leachate stemming from seagrass leaves steeped in the lagoon. Our measurements in the lagoon showed a strong attenuation of ultraviolet radiation, not observed in the waters outside the lagoon, and laboratory examination confirmed that the strong UV absorption of substances leached into seawater from decomposing leaves of the seagrass Thalassodendron (=Cymodocea testudinaceum. Our findings demonstrate the synergism between elevated seawater temperature and UV radiation in triggering bleaching on shallow reefs.

  3. Behaviour of U-Isotopes in an Estuary Affected by Acid Mine Drainage and Industrial Releases

    Tinto and Odiel rivers (SW of Spain) is an ecosystem of great interest that is seriously affected by acid mine drainage (AMD) from long-term mining activities (pH < 3). Additionally, a large industrial complex is located in the surroundings of this estuary and Huelva town, which includes two phosphate rock processing plants that produce about 3 millions of tons per year of a byproduct called phosphogypsum (PG) containing high U-series radionuclides concentrations. For these reasons, the estuary of Huelva is one of the most heavy metals and radionuclides polluted estuarine systems in Europe with extremely low pH.

  4. A novel paleo-bleaching proxy using boron isotopes and high-resolution laser ablation to reconstruct coral bleaching events

    G. Dishon

    2015-06-01

    Full Text Available Coral reefs occupy only ~0.1% of the oceans habitat, but are the most biologically diverse marine ecosystem. In recent decades, coral reefs have experienced significant global declines due to a variety of causes, one of the major being widespread coral bleaching events. During bleaching the coral expels its symbiotic algae losing its main source of nutrition generally obtained through photosynthesis. While recent coral bleaching events have been extensively investigated, there is no scientific data on historical coral bleaching prior to 1979. In this study, we employ high-resolution femtosecond Laser Ablation Multiple Collector Inductively Coupled Plasma Mass Spectrometry (LA-MC-ICP-MS to demonstrate a distinct biologically-induced decline of boron (B isotopic composition (δ11B as a result of coral bleaching. These findings and methodology offer a new use for a previously developed isotopic proxy to reconstruct paleo-coral bleaching events. Based on a literature review of published δ11B data and our recorded "vital effect" of coral bleaching on the δ11B signal, we also describe at least two possible coral bleaching events since the Last Glacial Maximum. The implementation of this bleaching proxy holds the potential of identifying occurrences of coral bleaching throughout the geological record. A deeper temporal view of coral bleaching will enable scientists to determine if it occurred in the past during times of environmental change and what outcome it may have had on coral population structure.

  5. Immune defenses of healthy, bleached and diseased Montastraea faveolata during a natural bleaching event.

    Mydlarz, Laura D; Couch, Courtney S; Weil, Ernesto; Smith, Garriet; Harvell, C Drew

    2009-11-16

    One prominent hypothesis regarding climate change and scleractinian corals is that thermal stress compromises immune competence. To test this hypothesis we tracked how the immune defenses of bleached, apparently healthy and yellow band disease (YBD) diseased Montastraea faveolata colonies varied with natural thermal stress in southwestern Puerto Rico. Colonies were monitored for 21 mo from the peak of the bleaching event in October 2005 to August 2007. Since sea surface temperature was significantly higher in summer and fall 2005 than 2006, year of collection was used as a proxy for temperature stress, and colony fragments collected in 2005 were compared with those collected in 2006. Mortality rate was high (43% overall) and all colonies (except one) either died or became infected with YBD by August 2007. YBD-infected tissue did not bleach (i.e. expel zooxanthellae) during the 2005 bleaching event, even when healthy tissue of these colonies bleached. Immune activity was assayed by measuring prophenoloxidase (PPO), peroxidase (POX), lysozyme-like (LYS) and antibacterial (AB) activity. Immune activity was variable between all coral samples, but there was a significant elevation of PPO activity in bleached colonies collected in 2005 relative to apparently healthy and YBD-diseased corals in 2006. In YBD-diseased colonies, LYS and AB activity were elevated in both healthy and infected tissue, indicating a systemic response; activity levels in these colonies were higher compared to those that appeared healthy. In both these immune parameters, there was a trend for suppression of activity in corals that were bleached in 2005. These data, while complicated by between-genet variability, illustrate the complex interaction between disease and temperature stress on immune function. PMID:20095242

  6. Changes in bleaching susceptibility among corals subject to ocean warming and recurrent bleaching in Moorea, French Polynesia.

    Morgan S Pratchett

    Full Text Available BACKGROUND: Climate-induced coral bleaching poses a major threat to coral reef ecosystems, mostly because of the sensitivities of key habitat-forming corals to increasing temperature. However, susceptibility to bleaching varies greatly among coral genera and there are likely to be major changes in the relative abundance of different corals, even if the wholesale loss of corals does not occur for several decades. Here we document variation in bleaching susceptibility among key genera of reef-building corals in Moorea, French Polynesia, and compare bleaching incidence during mass-bleaching events documented in 1991, 1994, 2002 and 2007. METHODOLOGY/PRINCIPAL FINDINGS: This study compared the proportion of colonies that bleached for four major genera of reef-building corals (Acropora, Montipora, Pocillopora and Porites, during each of four well-documented bleaching events from 1991 to 2007. Acropora and Montipora consistently bleached in far greater proportions (up to 98% than Pocillopora and Porites. However, there was an apparent and sustained decline in the proportion of colonies that bleached during successive bleaching events, especially for Acropora and Montipora. In 2007, only 77% of Acropora colonies bleached compared with 98% in 1991. Temporal variation in the proportion of coral colonies bleached may be attributable to differences in environmental conditions among years. Alternately, the sustained declines in bleaching incidence among highly susceptible corals may be indicative of acclimation or adaptation. CONCLUSIONS/SIGNIFICANCE: Coral genera that are highly susceptible to coral bleaching, and especially Acropora and Montipora, exhibit temporal declines in their susceptibility to thermal anomalies at Moorea, French Polynesia. One possible explanation for these findings is that gradual removal of highly susceptible genotypes (through selective mortality of individuals, populations, and/or species is producing a coral assemblage that is

  7. Perfluorooctanoic acid exposure for 28 days affects glucose homeostasis and induces insulin hypersensitivity in mice

    Yan, Shengmin; Zhang, Hongxia; Zheng, Fei; Sheng, Nan; Guo, Xuejiang; Dai, Jiayin

    2015-06-01

    Perfluoroalkyl acids (PFAAs) are widely used in many applications due to their unique physical and chemical characteristics. Because of the increasing prevalence of metabolic syndromes, including obesity, dyslipidemia and insulin resistance, concern has arisen about the roles of environmental pollutants in such diseases. Earlier epidemiologic studies showed a potential association between perfluorooctanoic acid (PFOA) and glucose metabolism, but how PFOA influences glucose homeostasis is still unknown. Here, we report on the modulation of the phosphatidylinositol 3-kinase-serine/threonine protein kinase (PI3K-AKT) signaling pathway in the livers of mice after 28 d of exposure to PFOA. Compared with normal mice, PFOA exposure significantly decreased the expression of the phosphatase and tensin homologue (PTEN) protein and affected the PI3K-AKT signaling pathway in the liver. Tolerance tests further indicated that PFOA exposure induced higher insulin sensitivity and glucose tolerance in mice. Biochemical analysis revealed that PFOA exposure reduced hepatic glycogen synthesis, which might be attributed to gluconeogenesis inhibition. The levels of several circulating proteins were altered after PFOA exposure, including proteins potentially related to diabetes and liver disease. Our results suggest that PFOA affected glucose metabolism and induced insulin hypersensitivity in mice.

  8. Expression, protein stability and transcriptional activity of retinoic acid receptors are affected by microtubules interfering agents and all-trans retinoic acid in primary rat hepatocytes

    2007-01-01

    Expression, protein stability and transcriptional activity of retinoic acid receptors are affected by microtubules interfering agents and all-trans retinoic acid in primary rat hepatocytes CZECH REPUBLIC (Dvorak, Zdenek) CZECH REPUBLIC Received: 2006-08-22 Revised: 2006-11-16 Accepted: 2007-01-02

  9. Basal omega-3 fatty acid status affects fatty acid and oxylipin responses to high-dose n3-HUFA in healthy volunteers

    Objective: Baseline concentrations of highly unsaturated omega-3 fatty acid (n3-HUFA) may influence the ability of dietary n3-HUFA to affect changes in concentrations of esterified fatty acids and their metabolites. This study evaluates the influence of basal n3-HUFA and n3-HUFA metabolite status ...

  10. Whole transcriptome analysis reveals changes in expression of immune-related genes during and after bleaching in a reef-building coral.

    Pinzón, Jorge H; Kamel, Bishoy; Burge, Colleen A; Harvell, C Drew; Medina, Mónica; Weil, Ernesto; Mydlarz, Laura D

    2015-04-01

    Climate change is negatively affecting the stability of natural ecosystems, especially coral reefs. The dissociation of the symbiosis between reef-building corals and their algal symbiont, or coral bleaching, has been linked to increased sea surface temperatures. Coral bleaching has significant impacts on corals, including an increase in disease outbreaks that can permanently change the entire reef ecosystem. Yet, little is known about the impacts of coral bleaching on the coral immune system. In this study, whole transcriptome analysis of the coral holobiont and each of the associate components (i.e. coral host, algal symbiont and other associated microorganisms) was used to determine changes in gene expression in corals affected by a natural bleaching event as well as during the recovery phase. The main findings include evidence that the coral holobiont and the coral host have different responses to bleaching, and the host immune system appears suppressed even a year after a bleaching event. These results support the hypothesis that coral bleaching changes the expression of innate immune genes of corals, and these effects can last even after recovery of symbiont populations. Research on the role of immunity on coral's resistance to stressors can help make informed predictions on the future of corals and coral reefs. PMID:26064625

  11. Exudation of organic acids by Lupinus albus and Lupinus angustifolius as affected by phosphorus supply

    Hentschel, Werner; Wiche, Oliver

    2016-04-01

    In phytomining and phytoremediation research mixed cultures of bioenergy crops with legumes hold promise to enhance availability of trace metals and metalloids in the soil plant system. This is due to the ability of certain legumes to mobilize trace elements during acquisition of nutrients making these elements available for co-cultured species. The legumes achieve this element mobilization by exudating carboxylates and enzymes as well as by lowering the pH value in the rhizosphere. The aim of our research was to determine characteristics and differences in the exudation of Lupinus albus and Lupinus angustifolius regarding to quantitative as to qualitative aspects. Especially the affection by phosphorus (P) supply was a point of interest. Thus we conducted laboratory batch experiments, wherein the plants were grown over four weeks under controlled light, moisture and nutritional conditions on sand as substrate. Half of the plants were supplied with 12 mg P per kg substrate, the other half were cultivated under a total lack of P. After cultivation the plants were transferred from the cultivation substrate into a 0,05 mmolṡL‑1 CaCl2 solution. After two hours the plants were removed, moist and dry mass off shoots and roots were measured together with the root length (Tennants' method). Concentrations of exudated carboxylates in the CaCl2 solution were determined via IC (column: Metrosept OrganicAcids, eluent 0.5 molṡL‑1 H2SO4 + 15% acetone, pH=3; 0.5 mLṡmin‑1). As a result four different organic acids were identified (citric acid, fumaric acid, tartaric acid, malic acid) in concentration ranges of 0.15 mgṡL‑1 (fumaric acid) to 9.21 mgṡL‑1 (citric acid). Lupinus angustifolius showed a higher exudation rate (in nmol per cm root length per hour) than Lupinus albus in the presence of phosphorus (e.g. regarding citric acid: 1.99 vs 0.64 nmolṡ(gṡh)‑1). However, as the root complexity and length of L. albus were far higher than of L. angustifolius

  12. The ratio of unsaturated fatty acids in biosurfactants affects the efficiency of gene transfection.

    Inoh, Yoshikazu; Furuno, Tadahide; Hirashima, Naohide; Kitamoto, Dai; Nakanishi, Mamoru

    2010-10-15

    An unsaturated hydrocarbon chain in phospholipid was reported to affect a phase transition and a fusogenic activity after mixing membranes, and consequently to achieve a high DNA transfection efficiency. We previously showed that a biosurfactant mannosylerythritol lipid-A (MEL-A) enhances the gene transfection efficiency of cationic liposomes. Here, we have studied the effects of unsaturated fatty acid ratio of MEL-A on the physicochemical properties and gene delivery into cells of cationic liposomes using MEL-A with three different unsaturated fatty acid ratios (9.1%, 21.5%, and 46.3%). The gene transfer efficiency of cationic liposomes containing MEL-A (21.5%) was much higher than that of those containing MEL-A (9.1%) and MEL-A (46.3%). MEL-A (21.5%)-containing cationic liposomes induced highly efficient membrane fusion after addition of anionic liposomes and led to subsequent DNA release. Imaging analysis revealed that MEL-A (21.5%)-containing liposomes fused with the plasma membrane and delivered DNA into the nucleus of NIH-3T3 cells, MEL-A (46.3%)-containing liposomes fused with the plasma membrane did not deliver DNA into the nucleus, and MEL-A (9.1%)-containing liposomes neither fused with the plasma membrane nor delivered DNA into the nucleus. Thus, it is understandable that the unsaturated fatty acid ratio of MEL-A strongly influences the gene transfection efficiency of cationic liposomes. PMID:20674726

  13. Metagenomic analysis of the coral holobiont during a natural bleaching event on the Great Barrier Reef.

    Littman, Raechel; Willis, Bette L; Bourne, David G

    2011-12-01

    Understanding the effects of elevated seawater temperatures on each member of the coral holobiont (the complex comprised of coral polyps and associated symbiotic microorganisms, including Bacteria, viruses, Fungi, Archaea and endolithic algae) is becoming increasingly important as evidence accumulates that microbial members contribute to overall coral health, particularly during thermal stress. Here we use a metagenomic approach to identify metabolic and taxonomic shifts in microbial communities associated with the hard coral Acropora millepora throughout a natural thermal bleaching event at Magnetic Island (Great Barrier Reef). A direct comparison of metagenomic data sets from healthy versus bleached corals indicated major shifts in microbial associates during heat stress, including Bacteria, Archaea, viruses, Fungi and micro-algae. Overall, metabolism of the microbial community shifted from autotrophy to heterotrophy, including increases in genes associated with the metabolism of fatty acids, proteins, simple carbohydrates, phosphorus and sulfur. In addition, the proportion of virulence genes was higher in the bleached library, indicating an increase in microorganisms capable of pathogenesis following bleaching. These results demonstrate that thermal stress results in shifts in coral-associated microbial communities that may lead to deteriorating coral health. PMID:23761353

  14. Effect of ultrasonic pre-treatment of thermomechanical pulp on hydrogen peroxide bleaching

    Ultrasound pre-treatments of softwood TMP had been carried to evaluate its impact on the efficiency of hydrogen peroxide bleaching. The trials were performed after a factorial design of experiment using frequency, power and time as variables. The experiments were conducted in an ultrasonic bath and then bleached with hydrogen peroxide. Measurements such as brightness, L*A*B* color system coordinate, residual hydrogen peroxide and metal content were evaluated on bleached pulp. The results indicate that the effect of ultrasonic treatment on brightness was dependent on the ultrasound frequency used; the brightness increased slightly at 68 kHz and decreased at 40 and 170 kHz. These results were correlated to the ultrasound effect on the generation of transition metals (copper, iron and manganese) which are responsible for catalytic decomposition of hydrogen peroxide. The influence of metal interference was minimized by using a chelating agent such as diethylene triamine pentaacetic acid (DTPA). With the results obtained in this study we have identified a set of option conditions, e.g. 1000 W, 40 kHz, 1.5 % consistency and 0.2% addition of DTPA prior to the bleaching stage (after ultrasonic pre-treatment) who improve brightness by 2.5 %ISO.

  15. Side effects of external tooth bleaching

    E.M., Bruzell; Pallesen, Ulla; Thoresen, N.R.;

    2013-01-01

    -office = 39.3% [n = 28]; p >0.05; 95% CI [OR]: 0.198‑1.102) whereas prevalence of gingival irritation was higher after in-office treatment (at-home = 14.0%; in-office = 35.7%; p <0.05) (mean age: 37.3 years; 73.7% women; n = 171). At the second follow-up, two and three patients reported side effects...... attributed to the bleaching treatment in the at-home and in-office groups, respectively. Predictors for side effects were tooth sensitivity, surface loss and gingivitis when observed at inclusion. Treatment-related predictors were bleaching concentration and contact between tray and gingiva. Conclusions...

  16. Enzymes improve ECF bleaching of pulp

    Lachenal, D.; Bajpai, P. K.; S P Mishra; Sharma, N.; Anand, A; Bajpai, P.

    2006-01-01

    The delignification efficiency of different laccase enzymes was examined on the eucalyptus Kraft pulp. The laccase enzyme from Trametes versicolor showing the highest delignification efficiency was selected and used in the elemental chlorine-free bleaching sequence for improving the pulp bleachability. An appreciable reduction in chlorine dioxide consumption was also obtained. Further reduction in chlorine dioxide consumption was obtained when the same laccase treated pulp was subjected to an...

  17. How dietary arachidonic- and docosahexaenoic- acid rich oils differentially affect the murine hepatic transcriptome

    Roberts Matthew A

    2006-04-01

    Full Text Available Introduction Herein, we expand our previous work on the effects of long chain polyunsaturated fatty acids (LC-PUFA on the murine hepatic transcriptome using novel statistical and bioinformatic approaches for evaluating microarray data. The analyses focuses on key differences in the transcriptomic response that will influence metabolism following consumption of FUNG (rich in 20:4n6, FISH (rich in 20:5n3, 22:5n3, and 22:6n3 and COMB, the combination of the two. Results Using a variance-stabilized F-statistic, 371 probe sets (out of 13 K probe sets in the Affymetrix Mu11K chip set were changed by dietary treatment (P Conclusion Distinct transcriptomic, signaling cascades, and predicted affects on murine liver metabolism have been elucidated for 20:4n6-rich dietary oils, 22:6n3-rich oils, and a surprisingly distinct set of genes were affected by the combination of the two. Our results emphasize that the balance of dietary n6 and n3 LC-PUFA provided for infants and in nutritional and neutraceutical applications could have profoundly different affects on metabolism and cell signaling, beyond that previously recognized.

  18. Pigmentation changes in Siderastrea spp. during bleaching events in the costal reefs of northeastern Brazil

    Roberto Sassi

    2015-03-01

    Full Text Available We report here the occurrence of seasonal changes in the pigmentation of colonies of Siderastrea spp. during bleaching events on coastal reefs in northeastern Brazil. Bleached affected almost 50% of coral colonies analyzed in Cabo Branco reefs (Paraiba state in the summer of 2005. The same phenomenon was detected along various coastal reefs in northeastern Brazil during the summer of 2007 and 2008. These events were seasonal, and began with the emergence of pale colonies that became pale-pink and then purple during the rainy months. The patterns and intensity of colonies pigmentation changes varied with the studied sites. The decrease in zooxanthellae density and chlorophyll-a content was quantified in the colonies with their pigmentation pattern altered (bleaching. Microbiological analyses revealed higher densities of bacteria in pink colonies (bleached as compared to brown colonies (normal. Environmental disturbances may lead to the pigmentation changes in Siderastrea spp., but the immediate causes of this phenomenon are not clear and require further investigations.

  19. Coral reef recovery status in south Andaman Islands after the bleaching event 2010

    Marimuthu, N.; Jerald Wilson, J.; Vinithkumar, N. V.; Kirubagaran, R.

    2013-03-01

    The Andaman and Nicobar Islands are one of the Union Territories of India, located in the eastern part of the Bay of Bengal. In 2010 summer, the increment in sea surface water temperature (up to 34°C) resulted in the bleaching of about 74% to 77% of corals in the South Andaman. During this event, coral species such as Acropora cerealis, A. humilis, Montipora sp., Favia pallida, Diploastrea sp., Goniopora sp. Fungia concinna, Gardineroseries sp., Porites sp., Favites abdita and Lobophyllia robusta were severely affected. This study is to assess the recovery status of the reef ecosystem by estimating the percentage of Live Coral cover, Bleached coral cover, Dead coral with algae, Rubble, Sandy flat, Algal assemblage and other associated organisms. The sedimentation rate (mg cm-2 d-1) and coral coverage (%) were assessed during this study period. The average sedimentation rate was ranged between 0.27 and 0.89 mg cm-2 d-1. The observed post bleaching recovery of coral cover was 21.1% at Port Blair Bay and 13.29% at Havelock Island. The mortality rate of coral cover due to this bleaching was estimated as 2.05% at Port Blair Bay and 9.82% at Havelock Island. Once the sea water temperature resumed back to the normal condition, most of the corals were found recovered.

  20. Coral Reef Recovery Status in South Andaman Islands after the Bleaching Event 2010

    N. Marimuthu; J. Jerald Wilson; N.V. Vinithkumar; R. Kirubagaran

    2013-01-01

    The Andaman and Nicobar Islands are one of the Union Territories of India,located in the eastern part of the Bay of Bengal.In 2010 summer,the increment in sea surface water temperature (up to 34℃) resulted in the bleaching of about 74% to 77% of corals in the South Andaman.During this event,coral species such as Acropora cerealis,A.humilis,Montipora sp.,Favia pallida,Diploastrea sp.,Goniopora sp.Fungia concinna,Gardineroseries sp.,Porites sp.,Favites abdita and Lobophyllia robusta were severely affected.This study is to assess the recovery status of the reef ecosystem by estimating the percentage of Live Coral cover,Bleached coral cover,Dead coral with algae,Rubble,Sandy fiat,Algal assemblage and other associated organisms.The sedimentation rate (mg cm-2 d-1) and coral coverage (%) were assessed during this study period.The average sedimentation rate was ranged between 0.27 and 0.89mg cm-2 d-1.The observed post bleaching recovery of coral cover was 21.1% at Port Blair Bay and 13.29% at Havelock Island.The mortality rate of coral cover due to this bleaching was estimated as 2.05% at Port Blair Bay and 9.82% at Havelock Island.Once the sea water temperature resumed back to the normal condition,most of the corals were found recovered.

  1. A study on the recovery of Tobago's coral reefs following the 2010 mass bleaching event.

    Buglass, Salome; Donner, Simon D; Alemu I, Jahson B

    2016-03-15

    In 2010, severe coral bleaching was observed across the southeastern Caribbean, including the island of Tobago, where coral reefs are subject to sedimentation and high nutrient levels from terrestrial runoff. Here we examine changes in corals' colony size distributions over time (2010-2013), juvenile abundances and sedimentation rates for sites across Tobago following the 2010 bleaching event. The results indicated that since pre-bleaching coral cover was already low due to local factors and past disturbance, the 2010 event affected only particular susceptible species' population size structure and increased the proportion of small sized colonies. The low density of juveniles (mean of 5.4±6.3 juveniles/m(-2)) suggests that Tobago's reefs already experienced limited recruitment, especially of large broadcasting species. The juvenile distribution and the response of individual species to the bleaching event support the notion that Caribbean reefs are becoming dominated by weedy non-framework building taxa which are more resilient to disturbances. PMID:26856646

  2. Biodiesel production from residual oils recovered from spent bleaching earth

    This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

  3. Anaerobic treatment of cellulose bleach plant wastewater: chlorinated organics and genotoxicity removal

    T. R. Chaparro; E. C. Pires

    2011-01-01

    This study assessed the removal efficiency of organic matter and how it relates to the decrease of toxic and mutagenic effects when an anaerobic reactor is used to treat the bleaching effluent from two kraft pulp mills. Parameters such as COD (chemical oxygen demand), DOC (dissolved organic carbon), AOX (adsorbable organic halogen), ASL (acid soluble lignin), color, chlorides, total phenols and absorbance values in the UV-VIS spectral region were measured. The acute and chronic toxicity and g...

  4. Integrating a xylanase treatment into an industrial-type sequence for eucalyptus kraft pulp bleaching

    Fillat Latorre, Úrsula; Roncero Vivero, María Blanca; Sacón, Vera Maria; Bassa, Alexandre

    2012-01-01

    The influence of a treatment with two commercial xylanases on pulp and effluents obtained after the bleaching stages in the OXAZDP (O, oxygen stage; X, xylanase treatment; A, acid stage; Z, ozone stage; D, chlorine dioxide stage; P, hydrogen peroxide stage) sequence was studied. Also, the potential saving in chlorine dioxide was assessed. The enzyme treatment was performed on pulp containing some black liquor since the operating conditions were close to the conditions used in the storage towe...

  5. Mass Coral Bleaching in 2010 in the Southern Caribbean

    Alemu I, Jahson Berhane; Clement, Ysharda

    2014-01-01

    Ocean temperatures are increasing globally and the Caribbean is no exception. An extreme ocean warming event in 2010 placed Tobago's coral reefs under severe stress resulting in widespread coral bleaching and threatening the livelihoods that rely on them. The bleaching response of four reef building taxa was monitored over a six month period across three major reefs systems in Tobago. By identifying taxa resilient to bleaching we propose to assist local coral reef managers in the decision mak...

  6. Dental pulp vascular permeability changes induced by dental bleaching

    Cristiane da Costa; Sueli Patricia Harumi Miyagi; Marcelo dos Santos; Manoel Eduardo de Lima Machado; Márcia Martins Marques

    2012-01-01

    Aiming to compare the effect of different light sources for dental bleaching on vascular permeability of dental pulps, forty-eight incisors were used. The bleaching agent (35 % hydrogen peroxide) was activated by halogen light; LED (Light Emitting Diode) or LED, followed by laser phototherapy (LPT) (λ = 780 nm; 3 J/cm²). After the bleaching procedures, the animals received an intra-arterial dye injection and one hour later were sacrificed. The teeth were diaphanized and photographed. The...

  7. Effectiveness of bleaching agent on composite resin discoloration

    Galih Sampoerno

    2012-01-01

    Background: The discoloration of teeth, especially anterior teeth, is one of aesthetic problems. The use of tooth bleaching agents for discolored natural teeth is becoming increasingly popular. Many dentists, however, get many problems when they conduct bleaching process since there is much composite filling on patient’s anterior teeth. Although many research have focused on the discoloration of composite resin after bleaching process, the problem still becomes debatable. Purpose: The purpose...

  8. Coral community response to bleaching on a highly disturbed reef

    Guest, J R; Low, J.; Tun, K.; Wilson, B.; Ng, C.; D. Raingeard; Ulstrup, K. E.; Tanzil, J. T. I.; Todd, P.A.; Toh, T. C.; McDougald, D; Chou, L. M.; Steinberg, P D

    2016-01-01

    While many studies of coral bleaching report on broad, regional scale responses, fewer examine variation in susceptibility among coral taxa and changes in community structure, before, during and after bleaching on individual reefs. Here we report in detail on the response to bleaching by a coral community on a highly disturbed reef site south of mainland Singapore before, during and after a major thermal anomaly in 2010. To estimate the capacity for resistance to thermal stress, we report on:...

  9. A global protocol for monitoring of coral bleaching

    Oliver, J.; Setiasih, N.; Marshall, P.; Hansen, L.

    2004-01-01

    Coral bleaching and subsequent mortality represent a major threat to the future health and productivity of coral reefs. However a lack of reliable data on occurrence, severity and other characteristics of bleaching events hampers research on the causes and consequences of this important phenomenon. This article describes a global protocol for monitoring coral bleaching events, which addresses this problem and can be used by people with different levels of expertise and resources.

  10. Interactions between major chlorogenic acid isomers and chemical changes in coffee brew that affect antioxidant activities.

    Liang, Ningjian; Xue, Wei; Kennepohl, Pierre; Kitts, David D

    2016-12-15

    Coffee bean source and roasting conditions significantly (p<0.05) affected the content of chlorogenic acid (CGA) isomers, several indices of browning and subsequent antioxidant values. Principal component analysis was used to interpret the correlations between physiochemical and antioxidant parameters of coffee. CGA isomer content was positively correlated (p<0.001) to capacity of coffee to reduce nitric oxide and scavenge Frémy's salt. Indices of browning in roasted coffee were positively correlated (p<0.001) to ABTS and TEMPO radical scavenging capacity, respectively. Only the CGA content of coffee corresponded to intracellular antioxidant capacity measured in Caco-2 intestinal cells. This study concluded that the intracellular antioxidant capacity that best describes potential health benefits of coffee positively corresponds best with CGA content. PMID:27451179

  11. Identification of significant medium components that affect docosahexaenoic acid production by Schizochytrium sp. SW1

    Manikan, Vidyah; Hamid, Aidil A.

    2013-11-01

    Central composite design (CCD) was employed to investigate the significance of glucose, yeast extract, MSG and sea salt in affecting the amount of docosahexaenoic acid (DHA) accumulated by a locally isolated strain of Schizochytrium. Design Expert software was used to construct a set of experiments where each medium component mentioned above was varied over three levels. Cultivation was carried out in 250mL flasks containing 50mL of medium, incubated at 30°C with 200 rpm agitation for 96 hours. ANOVA was conducted to identify the influential factors and the level of their significance where factors that scored a probability value of less than 0.05 were considered significant. The level of influence for each independent variable was also interpreted using perturbation whereas pattern of interaction between the factors were interpreted using interaction plots. This experiment revealed that yeast extract and monosodium glutamate have significant influence on DHA accumulation process by Schizochytrium sp. SW1.

  12. Regeneration of irradiated optical fibres by photo-bleaching?

    It is known that a light power between 0,1 and 20 μW caused bleaching of colour centres, which implies a reduction of induced loss. Older fibres especially those with a core made of undoped, low OH silica, experience tremendous photo-bleaching. Light of shorter wavelengths has a higher bleaching efficiency than that of longer wavelengths and same light intensity. The investigations have demonstrated that the injection of photo-bleaching light of shorter wavelength and higher intensity can distinctly decrease the radiation-induced loss of Ge-doped fibres, especially at low temperatures. Another possibility to apply photo-bleaching by short wavelength is to regenerate fibres that are permanently installed in radiation environments. Modern undoped multi-mode (MM) step index (Si), Ge-doped MM graded index (Gi) and Ge-doped single-mode (SM) fibres that had been irradiated were submitted to bleaching light. In this article it is shown how loss reduction and necessary bleaching time depend on wavelength and intensity of the bleaching light, on fibre length (bleaching time) and on radiation dose. These results are promising for the regeneration of optical fibres in facilities where the fibres cannot be replaced easily by new ones. (A.C.)

  13. Coral community response to bleaching on a highly disturbed reef.

    Guest, J R; Low, J; Tun, K; Wilson, B; Ng, C; Raingeard, D; Ulstrup, K E; Tanzil, J T I; Todd, P A; Toh, T C; McDougald, D; Chou, L M; Steinberg, P D

    2016-01-01

    While many studies of coral bleaching report on broad, regional scale responses, fewer examine variation in susceptibility among coral taxa and changes in community structure, before, during and after bleaching on individual reefs. Here we report in detail on the response to bleaching by a coral community on a highly disturbed reef site south of mainland Singapore before, during and after a major thermal anomaly in 2010. To estimate the capacity for resistance to thermal stress, we report on: a) overall bleaching severity during and after the event, b) differences in bleaching susceptibility among taxa during the event, and c) changes in coral community structure one year before and after bleaching. Approximately two thirds of colonies bleached, however, post-bleaching recovery was quite rapid and, importantly, coral taxa that are usually highly susceptible were relatively unaffected. Although total coral cover declined, there was no significant change in coral taxonomic community structure before and after bleaching. Several factors may have contributed to the overall high resistance of corals at this site including Symbiodinium affiliation, turbidity and heterotrophy. Our results suggest that, despite experiencing chronic anthropogenic disturbances, turbid shallow reef communities may be remarkably resilient to acute thermal stress. PMID:26876092

  14. Mass coral bleaching in 2010 in the southern Caribbean.

    Jahson Berhane Alemu I

    Full Text Available Ocean temperatures are increasing globally and the Caribbean is no exception. An extreme ocean warming event in 2010 placed Tobago's coral reefs under severe stress resulting in widespread coral bleaching and threatening the livelihoods that rely on them. The bleaching response of four reef building taxa was monitored over a six month period across three major reefs systems in Tobago. By identifying taxa resilient to bleaching we propose to assist local coral reef managers in the decision making process to cope with mass bleaching events. The bleaching signal (length of exposure to high ocean temperatures varied widely between the Atlantic and Caribbean reefs, but regardless of this variation most taxa bleached. Colpophyllia natans, Montastraea faveolata and Siderastrea siderea were considered the most bleaching vulnerable taxa. Interestingly, reefs with the highest coral cover showed the greatest decline reef building taxa, and conversely, reefs with the lowest coral cover showed the most bleaching but lowest change in coral cover with little algal overgrowth post-bleaching.

  15. Movement of Phosphorus in a Calcareous Soil as Affected by Humic Acid

    DU Zhen-Yu; WANG Qing-Hua; LIU Fang-Chun; MA Hai-Lin; MA Bing-Yao; S.S.MALHI

    2013-01-01

    When humic acid (HA) and phosphorus (P) fertilizer are simultaneously applied to soil,HA may affect the movement of P.A laboratory incubation experiment was conducted to quantify the effects of a commercial HA product co-applied with monocalcium phosphate (MCP) on the distance of P movement and the concentration of P in various forms at different distances from the P fertilizer application site in a calcareous soil from northern China.Fertilizer MCP (at a rate equivalent to 26.6 kg P ha-1) was applied alone or in combination with HA (at 254.8 kg HA ha-1) to the surface of soil packed in cylinders (150 mm high and 50 mm internal diameter),and then incubated at 320 g kg-1 moisture content for 7 and 28 d periods.Extraction and analysis of each 2 mm soil layer in columns showed that the addition of HA to MCP increased the distance of P movement and the concentrations of water-extractable P,acid-extractable P and Olsen P in soil.The addition of HA to MCP could enhance P availability by increasing the distance of P movement and the concentration of extractable P in soil surrounding the P fertilizer.

  16. Solar photocatalytic degradation of naphthenic acids in oil sands process-affected water.

    Leshuk, Tim; Wong, Timothy; Linley, Stuart; Peru, Kerry M; Headley, John V; Gu, Frank

    2016-02-01

    Bitumen mining in the Canadian oil sands creates large volumes of oil sands process-affected water (OSPW), the toxicity of which is due in part to naphthenic acids (NAs) and other acid extractable organics (AEO). The objective of this work was to evaluate the potential of solar photocatalysis over TiO2 to remove AEO from OSPW. One day of photocatalytic treatment under natural sunlight (25 MJ/m(2) over ∼14 h daylight) eradicated AEO from raw OSPW, and acute toxicity of the OSPW toward Vibrio fischeri was eliminated. Nearly complete mineralization of organic carbon was achieved within 1-7 day equivalents of sunlight exposure, and degradation was shown to proceed through a superoxide-mediated oxidation pathway. High resolution mass spectrometry (HRMS) analysis of oxidized intermediate compounds indicated preferential degradation of the heavier and more cyclic NAs (higher number of double bond equivalents), which are the most environmentally persistent fractions. The photocatalyst was shown to be recyclable for multiple uses, and thus solar photocatalysis may be a promising "green" advanced oxidation process (AOP) for OSPW treatment. PMID:26539710

  17. Survey of SSC12 regions affecting fatty acid composition of intramuscular fat using high density SNP data

    María eMuñoz

    2012-01-01

    Full Text Available Fatty acid composition is a critical aspect of pork because it affects sensorial and technological aspects of meat quality and it is relevant for human health. Previous studies identified significant QTLs in porcine chromosome 12 for fatty acid profile of backfat and intramuscular fat. In the present study, 374 SNPs mapped in SSC12 from the 60K Porcine SNP Beadchip were used. We have combined linkage and association analyses with expression data analysis in order to identify regions of SSC12 that could affect fatty acid composition of intramuscular fat in longissimus muscle. The QTL scan showed a region around the 60 cM position that significantly affects palmitic fatty acid and two related fatty acid indexes. The Iberian QTL allele increased the palmitic content (+2.6% of mean trait. This QTL does not match any of those reported in the previous study on fatty acid composition of backfat, suggesting different genetic control acting at both tissues. The SNP association analyses showed significant associations with linolenic and palmitic acids besides several indexes. Among the polymorphisms that affect palmitic fatty acid and match the QTL region at 60 cM, there were three that mapped in the Phosphatidylcholine Transfer Protein (PCTP gene and one in the Acetyl-CoA Carboxylase  gene (ACACA. Interestingly one of the PCTP SNPs also affected significantly unsaturated and double bound indexes and the ratio between polyunsaturated/monounsaturated fatty acids. Differential expression was assessed on longissimus muscle conditional on the genotype of the QTL and on the most significant SNPs, according to the results obtained in the former analyses. Results from the microarray expression analyses, validated by RT-qPCR, showed that PCTP expression levels significantly vary depending on the QTL as well as on the own PCTP genotype. The results obtained with the different approaches point out the PCTP gene as a powerful candidate underlying the QTL for

  18. Changes in Bleaching Susceptibility among Corals Subject to Ocean Warming and Recurrent Bleaching in Moorea, French Polynesia

    Pratchett, Morgan S.; McCowan, Dominique; Maynard, Jeffrey A; Heron, Scott F.

    2013-01-01

    Background Climate-induced coral bleaching poses a major threat to coral reef ecosystems, mostly because of the sensitivities of key habitat-forming corals to increasing temperature. However, susceptibility to bleaching varies greatly among coral genera and there are likely to be major changes in the relative abundance of different corals, even if the wholesale loss of corals does not occur for several decades. Here we document variation in bleaching susceptibility among key genera of reef-bu...

  19. A novel paleo-bleaching proxy using boron isotopes and high-resolution laser ablation to reconstruct coral bleaching events

    Dishon, G.; Fisch, J.; Horn, I.; Kaczmarek, K.; Bijma, J.; Gruber, D. F.; Nir, O.; Popovich, Y.; Tchernov, D.

    2015-10-01

    Coral reefs occupy only ~ 0.1 percent of the ocean's habitat, but are the most biologically diverse marine ecosystem. In recent decades, coral reefs have experienced a significant global decline due to a variety of causes, one of the major causes being widespread coral bleaching events. During bleaching, the coral expels its symbiotic algae, thereby losing its main source of nutrition generally obtained through photosynthesis. While recent coral bleaching events have been extensively investigated, there is no scientific data on historical coral bleaching prior to 1979. In this study, we employ high-resolution femtosecond Laser Ablation Multiple Collector Inductively Coupled Plasma Mass Spectrometry (LA-MC-ICP-MS) to demonstrate a distinct biologically induced decline of boron (B) isotopic composition (δ11B) as a result of coral bleaching. These findings and methodology offer a new use for a previously developed isotopic proxy to reconstruct paleo-coral bleaching events. Based on a literature review of published δ11B data and our recorded vital effect of coral bleaching on the δ11B signal, we also describe at least two possible coral bleaching events since the Last Glacial Maximum. The implementation of this bleaching proxy holds the potential of identifying occurrences of coral bleaching throughout the geological record. A deeper temporal view of coral bleaching will enable scientists to determine if it occurred in the past during times of environmental change and what outcome it may have had on coral population structure. Understanding the frequency of bleaching events is also critical for determining the relationship between natural and anthropogenic causes of these events.

  20. A novel paleo-bleaching proxy using boron isotopes and high-resolution laser ablation to reconstruct coral bleaching events

    Dishon, G.; Fisch, J.; Horn, I.; K. Kaczmarek; Bijma, J.; D. F. Gruber; O. Nir; Y. Popovich; D. Tchernov

    2015-01-01

    Coral reefs occupy only ~0.1% of the oceans habitat, but are the most biologically diverse marine ecosystem. In recent decades, coral reefs have experienced significant global declines due to a variety of causes, one of the major being widespread coral bleaching events. During bleaching the coral expels its symbiotic algae losing its main source of nutrition generally obtained through photosynthesis. While recent coral bleaching events hav...

  1. A novel paleo-bleaching proxy using boron isotopes and high-resolution laser ablation to reconstruct coral bleaching events

    Dishon, G.; Fisch, J.; Horn, I.; K. Kaczmarek; Bijma, J.; D. F. Gruber; O. Nir; Y. Popovich; D. Tchernov

    2015-01-01

    Coral reefs occupy only ~ 0.1 percent of the ocean's habitat, but are the most biologically diverse marine ecosystem. In recent decades, coral reefs have experienced a significant global decline due to a variety of causes, one of the major causes being widespread coral bleaching events. During bleaching, the coral expels its symbiotic algae, thereby losing its main source of nutrition generally obtained through photosynthesis. While recent coral bleaching events have been ex...

  2. The Salicylic Acid-Mediated Release of Plant Volatiles Affects the Host Choice of Bemisia tabaci.

    Shi, Xiaobin; Chen, Gong; Tian, Lixia; Peng, Zhengke; Xie, Wen; Wu, Qingjun; Wang, Shaoli; Zhou, Xuguo; Zhang, Youjun

    2016-01-01

    The whitefly Bemisia tabaci (Gennadius) (Hemiptera: Aleyrodidae) causes serious crop losses worldwide by transmitting viruses. We have previously shown that salicylic acid (SA)-related plant defenses directly affect whiteflies. In this study, we applied exogenous SA to tomato plants in order to investigate the interaction between SA-induced plant volatiles and nonviruliferous B. tabaci B and Q or B- and Q-carrying tomato yellow leaf curl virus (TYLCV). The results showed that exogenous SA caused plants to repel nonviruliferous whiteflies, but the effect was reduced when the SA concentration was low and when the whiteflies were viruliferous. Exogenous SA increased the number and quantity of plant volatiles-especially the quantity of methyl salicylate and δ-limonene. In Y-tube olfactometer assays, methyl salicylate and δ-limonene repelled the whiteflies, but the repellency was reduced for viruliferous Q. We suggest that the release of plant volatiles as mediated by SA affects the interaction between whiteflies, plants, and viruses. Further studies are needed to determine why viruliferous Q is less sensitive than nonviruliferous Q to repellent plant volatiles. PMID:27376280

  3. Selection for low erucic acid and genetic mapping of loci affecting the accumulation of very long-chain fatty acids in meadowfoam seed storage lipids.

    Gandhi, S D; Kishore, V K; Crane, J M; Slabaugh, M B; Knapp, S J

    2009-06-01

    Erucic acid (22:1(13)) has been identified as an anti-nutritional compound in meadowfoam (Limnanthes alba) and other oilseeds in the Brassicales, a classification which has necessitated the development of low erucic acid cultivars for human consumption. The erucic acid concentrations of meadowfoam wild types (8%-24%) surpass industry standards for human consumption (acid lines and identify loci affecting the accumulation of 22:1(13) and other very long-chain fatty acids (VLCFAs) in meadowfoam seed storage lipids. LE76, a low erucic acid line, was developed by 3 cycles of selection in an ethyl methanesulfonate-treated wildtype population. LE76 produced 3% 22:1(13), threefold less than the M0 population. Wildtype x LE76 F2 populations produced continuous, approximately normal erucic and dienoic acid distributions. Loss-of-function mutations apparently did not segregate and individuals with low 22:1(13) concentrations (affecting VLCFA profiles in seed storage lipids by genotyping and phenotyping wildtype x low erucic acid F2 progeny. Composite interval mapping identified 3 moderately large-effect erucic acid QTL. The low erucic acid parent transmitted favorable alleles for 2 of 3 QTL, suggesting low erucic acid cultivars can be developed by combining favorable alleles transmitted by wildtype and low erucic acid parents. PMID:19483773

  4. Environmental factors affecting the low temperature isomerization of homohopanes in acidic peat deposits, central China

    Huang, Xianyu; Meyers, Philip A.; Xue, Jiantao; Gong, Linfeng; Wang, Xinxin; Xie, Shucheng

    2015-04-01

    Progressively more evidence reveals the abundant occurrence of the C31 homohopane with a 17α, 21β-configuration (C31 αβ) in immature peats. This compound is commonly considered to be an indicator of thermal maturity in petroleum source rocks, but in peats it has also been interpreted to reflect the oxidation and subsequent decarboxylation reactions of bacteriohopanepolyols with microbially mediated epimerization at C-17 that is catalyzed by the acidic peat conditions. To learn more about the environmental factors that affect the low-temperature isomerization of homohopanes, we investigated the distribution patterns of homohopanes in a well-studied peat core from the Dajiuhu peatland, central China, together with data from modern surface peat samples from Dajiuhu and three other locations. From comparison with paleotemperature and paleohydrologic records in the peat core, we hypothesize that the ratio of C31 αβ hopane relative to the ββ isomer (C31 αβ/ββ) is mainly influenced on a centennial to millennial timescale by ambient temperature with a secondary effect from redox conditions that are defined by peatland water levels. The surface peat samples revealed that relatively high C31 αβ/ββ values occurred under pH < 6. These results suggest that pH is indeed an important factor in the low-temperature isomerization of C31 homohopanes, although the magnitude of the pH effect may be less than those of ambient temperature and redox conditions. In both surface peat and peat horizons from the Dajiuhu peatland, the amount of the C31 αβ compound with R configuration relative to that with S configuration (C31 R/S) varied closely with C31 αβ/ββ, suggesting that the epimerization at both C-17 and C-22 may happen synchronously and at similar rates. This study reveals that the isomerization of homohopanes has the potential to reflect paleoenvironmental changes in acidic peat deposits. In addition, acidic peat samples investigated in this and previous studies

  5. PROCESS OPTIMIZATION OF TETRA ACETYL ETHYLENE DIAMINE ACTIVATED HYDROGEN PEROXIDE BLEACHING OF POPULUS NIGRA CTMP

    Qiang Zhao; Junwen Pu; Shulei Mao; Guibo Qi

    2010-01-01

    To enhance the bleaching efficiency, the activator of tetra acetyl ethylene diamine (TAED) was used in conventional H2O2 bleaching. The H2O2/TAED bleaching system can accelerate the reaction rate and shorten bleaching time at relative low temperature, which can reduce the production cost. In this research, the process with hydrogen peroxide activated by TAED bleaching of Populus nigra chemi-thermo mechanical pulp was optimized. Suitable bleaching conditions were confirmed as follows: pulp con...

  6. Coral disease following massive bleaching in 2005 causes 60% decline in coral cover on reefs in the US Virgin Islands

    Miller, J.; Muller, E.; Rogers, C.; Waara, R.; Atkinson, A.; Whelan, K.R.T.; Patterson, M.; Witcher, B.

    2009-01-01

    In the northeast Caribbean, doldrum-like conditions combined with elevated water temperatures in the summer/fall 2005 created the most severe coral bleaching event ever documented within this region. Video monitoring of 100 randomly chosen, permanent transects at five study sites in the US Virgin Islands revealed over 90% of the scleractinian coral cover showed signs of thermal stress by paling or becoming completely white. Lower water temperatures in October allowed some re-coloring of corals; however, a subsequent unprecedented regional outbreak of coral disease affected all sites. Five known diseases or syndromes were recorded; however, most lesions showed signs similar to white plague. Nineteen scleractinian species were affected by disease, with >90% of the disease-induced lesions occurring on the genus Montastraea. The disease outbreak peaked several months after the onset of bleaching at all sites but did not occur at the same time. The mean number of disease-induced lesions increased 51-fold and the mean area of disease-associated mortality increased 13-fold when compared with pre-bleaching disease levels. In the 12 months following the onset of bleaching, coral cover declined at all sites (average loss: 51.5%, range: 42.4-61.8%) reducing the five-site average from 21.4% before bleaching to 10.3% with most mortality caused by white plague disease, not bleaching. Continued losses through October 2007 reduced the average coral cover of the five sites to 8.3% (average 2-year loss: 61.1%, range: 53.0-79.3%). Mean cover by M. annularis (complex) decreased 51%, Colpophyllia natans 78% and Agaricia agaricites 87%. Isolated disease outbreaks have been documented before in the Virgin Islands, but never as widespread or devastating as the one that occurred after the 2005 Caribbean coral-bleaching event. This study provides insight into the effects of continued seawater warming and subsequent coral bleaching events in the Caribbean and highlights the need to

  7. Ocean acidification causes bleaching and productivity loss in coral reef builders

    Anthony, K. R. N.; Kline, D. I.; Diaz-Pulido, G.; Dove, S.; Hoegh-Guldberg, O

    2008-01-01

    Ocean acidification represents a key threat to coral reefs by reducing the calcification rate of framework builders. In addition, acidification is likely to affect the relationship between corals and their symbiotic dinoflagellates and the productivity of this association. However, little is known about how acidification impacts on the physiology of reef builders and how acidification interacts with warming. Here, we report on an 8-week study that compared bleaching, productivity, and calcifi...

  8. Physiological and biogeochemical traits of bleaching and recovery in the mounding species of coral Porites lobata: implications for resilience in mounding corals.

    Stephen J Levas

    Full Text Available Mounding corals survive bleaching events in greater numbers than branching corals. However, no study to date has determined the underlying physiological and biogeochemical trait(s that are responsible for mounding coral holobiont resilience to bleaching. Furthermore, the potential of dissolved organic carbon (DOC as a source of fixed carbon to bleached corals has never been determined. Here, Porites lobata corals were experimentally bleached for 23 days and then allowed to recover for 0, 1, 5, and 11 months. At each recovery interval a suite of analyses were performed to assess their recovery (photosynthesis, respiration, chlorophyll a, energy reserves, tissue biomass, calcification, δ(13C of the skeletal, δ(13C, and δ(15N of the animal host and endosymbiont fractions. Furthermore, at 0 months of recovery, the assimilation of photosynthetically acquired and zooplankton-feeding acquired carbon into the animal host, endosymbiont, skeleton, and coral-mediated DOC were measured via (13C-pulse-chase labeling. During the first month of recovery, energy reserves and tissue biomass in bleached corals were maintained despite reductions in chlorophyll a, photosynthesis, and the assimilation of photosynthetically fixed carbon. At the same time, P. lobata corals catabolized carbon acquired from zooplankton and seemed to take up DOC as a source of fixed carbon. All variables that were negatively affected by bleaching recovered within 5 to 11 months. Thus, bleaching resilience in the mounding coral P. lobata is driven by its ability to actively catabolize zooplankton-acquired carbon and seemingly utilize DOC as a significant fixed carbon source, facilitating the maintenance of energy reserves and tissue biomass. With the frequency and intensity of bleaching events expected to increase over the next century, coral diversity on future reefs may favor not only mounding morphologies but species like P. lobata, which have the ability to utilize heterotrophic

  9. Conjugated linoleic acid of dairy foods is affected by cows’ feeding system and processing of milk

    Juan Pablo Avilez Ruiz

    2016-04-01

    Full Text Available ABSTRACT The distribution of conjugated linoleic acid (CLA in dairy products commercially available in Chile is poorly understood. This study aimed to assess the content of CLA in dairy cow products from Chile and the effect of processing fresh milk into dairy products. Samples of raw milk were categorized into two groups based on the animal feeding system utilized by the dairy farm: 1 grazing based systems (Los Lagos region; and 2 housing systems using total mixed ration (TMR diets (Los Angeles region. Simultaneously, commercial samples of condensed milk, powdered milk, butter and Gouda cheese were analyzed. Furthermore, samples of raw milk and processed products (powdered and sweetened condensed milk were also analyzed. Dairy farms based on grazing systems had higher levels of CLA in raw milk than TMR farms. In addition, average values of CLA were 1.72 g 100 g−1 of total fatty acids, in spring milk in the Los Lagos region, and 0.42 g 100 g−1 in summer milk, in the Los Angeles region. Similarly, the CLA content of dairy products was higher than that of raw milk. Milk processing affected the transferring of CLA from fresh milk into the final products. Sweetened condensed milk presented lower CLA values than raw and powdered milk. In conclusion, this study indicates the importance of the production systems to the CLA content as well as the effects of milk processing into dairy products. To sum up, more research is needed to elucidate the exact effect of the processing conditions of dairy products on the CLA content.

  10. Soil Components Affecting Phosphate Sorption Parameters of Acid Paddy Soils in Guangdong Province

    2000-01-01

    Soil components affecting phosphate sorption parameters were studied using acid paddy soils derived from basalt, granite, sand-shale and the Pearl River Delta sediments, respectively, in Guangdong Province.For each soil, seven 2.50 g subsamples were equilibrated with 50 mL 0.02 mol L-1 (pH=7.0) of KCl containing 0, 5, 10, 15, 25, 50 and 100 ng P kg-1, respectively, in order to derive P sorption parameters (P sorption maximum, P sorption intensity factor and maximum buffer capacity) by Langmuir isotherm equation. It was shown that the main soil components influencing phosphate sorption maximum (Xm) included soil clay, pH,amorphous iron oxide (Feo) and amorphous aluminum oxide (Alo), with their effects in the order of Alo >Feo > pH > clay. Among these components, pH had a negative effect, and the others had a positive effect.Organic matter (OM) was the only soil component influencing P sorption intensity factor (K). The main components influencing maximum phosphate buffer capacity (MBC) consisted of soil clay, OM, pH, Feo and Alo, with their effects in the order of Alo > OM > pH > Feo > clay. Path analysis indicated that among the components with positive effects on maximum phosphate buffer capacity (MBC), the effect was in the order of Alo > Feo > Clay, while among the components with negative effects, OM > pH. OM played an important role in mobilizing phosphate in acid paddy soils mainly through decreasing the sorption intensity of phosphate by soil particles.