International Nuclear Information System (INIS)

The consumption of food products obtained in areas subjected to radioactive contamination as a consequence of a radiation accident appears to be the most significant source of irradiation for the population. At the same time, this route can be regulated very effectively. The regularities of contamination of agricultural production, peculiar features of internal dose formation in the population and the effectiveness of countermeasures in agriculture have been analysed using the experience of two major accidents in the former USSR - in the South Urals (Kyshtym accident) in 1957, and at the Chernobyl NPP in 1986. (Author).

UK PubMed Central (United Kingdom)

The objectives of this study were to evaluate the current fitness of an area ambulance service based in Belfast and to quantify the physiological demands of accident and emergency work. From a total...Full Text Available

Science.gov (United States)

Accidents Accident Preparedness, Accident Prevention, Chemical Accidents, Radiation Accidents Characterization Contingency Plans National Contingency Plan (NCP), Oil Removal...

Science.gov (United States)

Accidents Accident Preparedness, Accident Prevention, Chemical Accidents, Radiation Accidents Characterization Contingency Plans National Contingency Plan (NCP), Oil Removal...

Energy Technology Data Exchange (ETDEWEB)

The results of a scoping study of onsite radiation exposures which could take place in each of three types of postulated reactor accidents are presented. The accident types are (1) a fuel handling accident at a Mark III BWR; an interfacing system LOCA or V sequence at a PWR; and and Anticipated Transient Without Scram (ATWS) at a Mark I BWR. Both external and internal dose pathways are considered. The results of the study indicate the prohibitively high radiation doses could be received in some plant areas if personnel were to remain there. However, times of the order of a few minutes to a few hours, depending on the type of accident, would be available before life-threatening doses would be accumulated assuming that the provided full face respiratory protection equipment were used promptly. Special attention was given radiation doses possibly received by control room personnel for ...

Energy Technology Data Exchange (ETDEWEB)

FLOWTRAN-TF is a new two-component, two-phase thermal-hydraulics code to capture the detailed assembly behavior associated with loss-of-coolant accident analyses in multichannel assemblies of the SRS reactors. The local interfacial area of the two-phase mixture is computed by summing the interfacial areas contributed by each of three flow regimes. For smooth flow regime transitions, the code uses an interpolation technique in terms of component void fraction for each basic flow regime.

Energy Technology Data Exchange (ETDEWEB)

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study.

International Nuclear Information System (INIS)

The main aim of sanitary pass-control regime is to prevent propagation of radioactive contamination outside the area of emergency-rescue works and guarantee of sanitary treatment of all persons having radioactive contamination. The paper has studied the questions of organization of sanitary pass-control regime, arrangement of sanitary treatment of the injured persons and rendering first aid in case of radioactive contamination of wounds. 5 refs.

Energy Technology Data Exchange (ETDEWEB)

This study examines the extent of radioactive pollution of moss cover of forest communities of the Kamenskii district of the Sverdlovsk region. This area contains the periphery section of the Eastern-Ural Radioactive Trace, formed as a result of the Kyshtymskii accident. Mosses do not release radionuclides for a long time, making them a biological indicator of radioactive environmental pollution and making them useful for radioecological monitoring. 14 refs., 2 figs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

Using longitudinal data from Ukraine we examine the extent of any long-lasting effects of exposure to the Chernobyl disaster on the health and labour market performance of the adult workforce. Variation in the local area level of radiation fallout from the Chernobyl accident is considered as a random exogenous shock with which to try to establish its causal impact on poor health, labour force participation, hours worked and wages. There appears to be a significant positive association between local area-level radiation dosage and perception of poor health, though much weaker associations between local area-level dosage and other specific self-reported health conditions. There is also some evidence to suggest that those who lived in areas more exposed to Chernobyl-induced radiation have sig...

International Nuclear Information System (INIS)

During the past 2 yr, significant progress has been made in several areas related to the safety and environmental (S and E) aspects of inertial fusion energy (IFE). An updated methodology has been developed, and accident analyses have been performed for two IFE conceptual power plants and a target fabrication facility. Parallel to the consequence analyses of different accident scenarios, ongoing studies of accident initiating events are being used to support safety assessment and create a basic framework of types of events to consider in future risk characterization of new plant designs. Target designers/fabrication specialists have been provided with ranking information related to the S and E characteristics of candidate target materials. We have revisited waste management options for IFE, introducing the concept of clearance versus the traditional shallow land burial. A brief summary of results in ...

International Nuclear Information System (INIS)

Plasma surface interactions in tokamaks are known to create significant quantities of dust, which settles onto surfaces and accumulates in the vacuum vessel. In ITER, a loss of vacuum accident may result in the release of dust which will be radioactive and/or toxic, and provides increased surface area for chemical reactions or dust explosion. A new method of analysis has been developed for modeling dust resuspension and transport in loss of vacuum accidents. The aerosol dynamic equation is solved via the user defined scalar (UDS) capability in the commercial CFD code Fluent. Fluent solves up to 50 generic transport equations for user defined scalars, and allows customization of terms in these equations through user defined functions (UDF). This allows calculation of diffusion coefficients based on local flow properties, inclusion of body forces such as gravity and thermophoresis in the convection term, and user defined ...

Energy Technology Data Exchange (ETDEWEB)

In the Carpathian Basin, significant percentage of watershed area and floodplains of rivers are utilised agriculturally. Several potential sources of poisonous metal pollution have been identified in these areas. Because of spills from some of them a few severe accidents have happened especially in the watershed area of Tisza River during the last decades. The motivation of our present work was to produce {sup 62,65}Zn and {sup 203}Pb radioisotopes because they can be used especially as tracers for studying the kinetics of uptake, transport and accumulation of zinc and lead by plants under different circumstances. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Energy Technology Data Exchange (ETDEWEB)

This report shows the probability of a catastrophic accident involving the WIPP waste hoist system. Calculations and mitigation to reduce the probability of an accident and to minimize the impact of such an accident should be included. 10 refs., 8 figs., 4 tabs.

International Nuclear Information System (INIS)

Short communication.

International Nuclear Information System (INIS)

... computer calculations fftf reactor nonlinear problems reactor accidents reactor

Energy Technology Data Exchange (ETDEWEB)

The mission of the Emerging Technologies thrust area at Lawrence Livermore National Laboratory is to help individuals establish technology areas that have national and commercial impact, and are outside the scope of the existing thrust areas. We continue to encourage innovative ideas that bring quality results to existing programs. We also take as our mission the encouragement of investment in new technology areas that are important to the economic competitiveness of this nation. In fiscal year 1992, we have focused on nine projects, summarized in this report: (1) Tire, Accident, Handling, and Roadway Safety; (2) EXTRANSYT: An Expert System for Advanced Traffic Management; (3) Odin: A High-Power, Underwater, Acoustic Transmitter for Surveillance Applications; (4) Passive Seismic Reservoir Monitoring: Signal Processing Innovations; (5) Paste Extrudable Explosive Aft Charge for ...

Science.gov (United States)

Automatic weapons such as machine guns and submachine guns are found in the German-speaking region only in special army and police units and appear accordingly rarely in homicides, suicides and accidents. In the following, the findings in two cases of death with the use of machine and submachine guns are presented. The first case was a fatal accident during shooting on a training area (current machine gun of the German army, calibre 7.62 x 51 mm), the second case was a killing during a physical conflict (submachine gun MP 40 from World War II, calibre 9 x 19 mm). In the case with the machine gun autopsy disclosed typical entry holes corresponding to the calibre, but unusually large exit wounds with tissue bridges in the wound ground, measuring 4 x 2.5 cm in diameter. By contrast, the second case (submachine gun) showed "normal" entry and exit wounds. The differences are mainly caused by deviating ballistic data of the ...

International Nuclear Information System (INIS)

The purpose of this document is to provide a framework for developing protective strategies in the longer term following an accidental release of radionuclides to the offsite environment. This advice covers all forms and scales of accidental release, including releases from nuclear sites and reactors, weapons accidents, and damaged industrial or medical sealed sources. The countermeasures considered are those intended to protect the public from external irradiation from radionuclides deposited in the environment, from the inhalation of resuspended radionuclides, and from inadvertent ingestion of radionuclides resulting from contact with contaminated surfaces. The Board terms these recovery countermeasures. They can be broadly grouped as either decontamination measures (ie measures that deal directly with the radionuclides, whether by removing them, shielding them or physically or chemically bonding them) or as restricted access measures (ie measures that reduce ...

International Nuclear Information System (INIS)

Accidents from three main practices: medical applications, industrial radiography and industrial irradiators are used to illustrate some common causes of accidents and the main lessons to be learned. A brief description of some of these accidents is given. Lessons learned from the described accidents are approached by subjects covering: safety culture, quality assurance, human factors, good engineering practice, defence in depth, security of sources, safety assessment and monitoring and verification compliance. (author)

Energy Technology Data Exchange (ETDEWEB)

Several steam generator tube rupture accidents have occurred at plants in the past. In this paper the Computational Multi-Fluid Dynamics (CMFD) investigation of the horizontal steam generator thermal-hydraulics during the tube rupture accident is performed. A guillotine of a steam generator U-tube is assumed with choked flow from the primary to the secondary side of the steam generator. We have computed water and steam velocity fields, steam volume fraction distribution on the steam generator secondary (shell) side, as well as the swell level increase. The simulation results are a support to the safety analyses of the steam generator tube rupture accident. Numerical simulation is performed with the multidimensional multi-fluid modelling approach. The two-phase flow around steam generator tubes in the bundle is modelled by the porous media approach. Interfacial mass, momentum and energy transfer are modelled with the closure ...

Energy Technology Data Exchange (ETDEWEB)

The program introduced here for determining and describing the multi-axial creep of pipes is based, on the one hand, on the results of the nuclear process heat prototype plant material program and, on the other hand, on the possible load conditions which arise for evaluating accidents or extreme working situations. The basis of a theoretical description of multi-axial creep is the invariant theory in which both the von Mises configuration change hypothesis and the Norton creep law are included. Combined tension and torsion are also considered in detail, the superimposition of cyclic stresses in the tensile threshold area is discussed and cases of partial relaxation are explained. Experimental results for the discussed loads are introduced, which have led to satisfactory agreement between theory and experiment. (orig./MM).

Energy Technology Data Exchange (ETDEWEB)

The Level 1 probabilistic safety assessment (PSA) for Wolsung(WS) 2/3/4 nuclear power plant (NPPs) in design stage is performed using the methodologies being equivalent to PWR PSA. Accident sequence evaluation program (ASEP) human reliability analysis (HRA) procedure and technique for human error rate prediction (THERR) are used in HRA of WS 2/3/4 NPPs PSA. The= purpose of this paper is to introduce the procedure and methodology of HRA in WS 2/3/4 NPPs PSA. Also, this paper describes the interim results of importance analysis for human actions modeled in WS 2/3/4 PSA and the findings and recommendations of administrative control of secondary control area from the view of human factors. (Author) 10 refs., 2 tabs.

CERN Document Server

As a result of nuclear power plant accidents, large areas receive radioactive inputs of Cs-137. This cesium accumulates in herbs growing in such territories. The problem is whether the herbs contaminated by radiocesium may be used as a raw material for medicine. The answer depends on the amount of Cs-137 transfered from the contaminated raw material to the medicine. We have presented new results of the transfer of Cs-137 from contaminated Digitalis grandiflora Mill. and Convallaria majalis L. to medicine. We found that the extraction of Cs-137 depends strongly on the hydrophilicity of the solvent. For example 96.5%(vol.) ethyl alcohol extracts less Cs-137 (11.6%) than 40%(vol.) ethyl alcohol or pure water (66.2%). The solubility of the cardiac glycosides is inverse to the solubility of cesium, which may be of use in the technological processes for manufacturing ecologically pure herbal medicine.

International Nuclear Information System (INIS)

Computer software for risk assessment of transportation of important freight has been developed. It incorporates models of transport accidents, including terrorist attacks. These models use, among the others, input data of cartographic character. Geographic information system technology and electronic maps of a geographic area are involved as an instrument for handling this kind of data. Fuzzy set theory methods as well as standard methods of probability theory have been used for quantitative risk assessment. Fuzzy algebraic operations and their computer realization are discussed. Risk assessment for one particular route of railway transportation is given as an example. (author)

International Nuclear Information System (INIS)

The accident assessment under emergency situation includes the accident status evaluation and its consequence estimation. This paper introduces evaluation methods for accident status and its assistant computer system (SESAME-GNP) utilized during the emergency situation in Guangdong Daya Bay Nuclear Power Station (GNPS) in detail. At the same time, an improved accident consequence estimation system in GNPS (RACAS-GNP) is briefly described. With the improvement of the accident assessment systems, the capability of emergency response in GNPS is strengthened

Energy Technology Data Exchange (ETDEWEB)

To make a quantitative comparison of risks between the SNR-300 and a modern PWR (Biblis B), the consequences of an accident or the extent of damage of a release of radionuclides to the environment due to an accident are estimated by computer programs for accident consequence models. The accident analysis includes an analysis of events for Bethe-Tait accidents with failure of the outer containment. The FGSB release rates are compared with those of the Society for Reactor Safety (GRS).

Energy Technology Data Exchange (ETDEWEB)

The Institute of Energetic and Nuclear Research - IPEN is a research and development institution, located in a densely populated area, in the city of Sao Paulo. The nuclear fuel cycle was developed from the Yellow Cake to the enrichment and reconversion at IPEN. After this phase, all the technology was transferred to private enterprises and to the Brazilian Navy (CTM/SP). Some plants of the fuel cycle were at semi-industrial level, with a production over 20 kg/h. As a research institute, IPEN accomplished its function of the fuel cycle, developing and transferring technology. With the necessity of space for the implementation of new projects, the uranium hexafluoride (UF{sub 6}) production plant was chosen, since it had been idle for many years and presented potential leaking risks, which could cause environmental aggression and serious accidents. This plant decommission required accurate planning, as this work had not been carried out in ...

Science.gov (United States)

The biological age (BA) of the majority of the liquidators of the consequences of the radiation accidents in the Navy and of the liquidators of the Chernobyl' APS accident exceeds the medium standard and the DBA (due BA). The index of the BA can be a characteristic of the influence of the social-hygienic factors on the health condition of the Special Risk Subunit--the liquidators of the consequences of the radiation accidents. It was established, that the radiation influence concerns to the factors dramatically increasing the BA and the rate of senescence of the liquidators of the consequences of the radiation accidents. PMID:21809627

Energy Technology Data Exchange (ETDEWEB)

A brief guide to training and equipment needed to effectively manage victims of radiation accidents. (DT)

International Nuclear Information System (INIS)

Industrial radiography accounts for approximately half of all the reported accidents for the nuclear related industry, in both developed and developing countries. This Safety Report is the result of a review made of a large selection of accidents in industrial radiography reported by regulatory authorities, professional associations and scientific journals. A small, representative selection of 43 accident descriptions has been used to illustrate the primary causes of radiography accidents, and a set of measures provided to prevent the recurrence of such accidents or to mitigate the consequences of those that do occur. These accident descriptions were categorized by primary causes as follows: inadequate regulatory control; failure to follow operational procedures; inadequate training; inadequate maintenance; human error; equipment malfunction or defect; design ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: The Nuclear Power Plants (NPPs) are always designed for the highest level of safety against postulated accidents which may be initiated due to internal or external causes. One of the external/internal causes, which may lead to accident in the reactor and its associated systems, is fire in certain vital areas of the plant. Conventionally, the fire containment approach and/or the fire confinement approach is used in designing the fire protection systems of NPPs. Indian NPPs (PHWRs) follow the combined approach to ensure plant safety and all newly designed plants are required to comply with the provisions of Atomic Energy Regulatory Board (AERB) fire safety Guide. In respect of older plants, the reassessment of adequacy of fire safety provisions in the light of current advances has becomes essential so as to decide upon the steps for retrofitting. Keeping this in mind the deterministic fire ...

Energy Technology Data Exchange (ETDEWEB)

Severe accident management can be defined as the use of existing and alternative resources, systems, and actions to prevent or mitigate a core-melt accident in nuclear power plants. TRAIN (Training pRogram for AMP In NPP), developed for training control room staff and the technical group, is introduced in this report. The TRAIN composes of phenomenological knowledge base (KB), accident sequence KB and accident management procedures with AM strategy control diagrams and information needs. This TRAIN might contribute to training them by obtaining phenomenological knowledge of severe accidents, understanding plant vulnerabilities, and solving problems under high stress. 24 refs., 76 figs., 102 tabs. (Author)

Energy Technology Data Exchange (ETDEWEB)

Human Reliability Analysis (HRA) is a very important part of Probabilistic Risk Analysis (PRA), and constant work is dedicated to improving methods, guidance and data in order to approach realism in the results as well as looking for ways to use these to reduce accident frequency at plants. Further, in order to advance in these areas, several HRA studies are being performed globally. Mexico has participated in the International HRA Empirical study with the objective of -benchmarking- HRA methods by comparing HRA predictions to actual crew performance in a simulator, as well as in the empirical study on a US nuclear power plant currently in progress. The focus of the first study was the development of an understanding of how methods are applied by various analysts, and characterize the methods for their capability to guide the analysts to identify potential human failures, and associated causes and performance shaping factors. The HRA ...

Energy Technology Data Exchange (ETDEWEB)

Severe accident analysis has been performed for the Wolsung nuclear power plants in Korea to investigate severe accident phenomena of CANDU-600 reactors as a part of Level II PSA study. The accident sequence analyzed in this paper is loss of active heat sinks (LOAH) which is caused by loss of off-site power, diesel generators, and DC power, ISAAC(Integrated Severe Accident Analysis Code) computer code developed by KAERI (Korea Atomic Energy Research Institute) was used in this analysis. This paper describes the important thermal-hydraulics and source term behaviors in the primary system and inside containment, and the failure mechanisms of calandria vessel and containment. In addition, some insights for accident management program (AMP) are also given.

International Nuclear Information System (INIS)

Following the 1986 Chernobyl accident there was an understandable increase in public interest in nuclear accidents and emergency planning for them. It became clear that the broad nature, timing and scale of the radiological hazard presented by such accidents was, however, little understood. This Paper sets out in simple terms the basic features of the radiological hazard to persons in the vicinity of a nuclear power plant should a serious accident occur. The Paper starts by stressing the difference between faults -events that may occur relatively frequently - and accidents -unplanned releases of radioactivity that are by design extremely unlikely events. The Paper examines the significance of different exposure pathways and relates them to the protective measures (countermeasures) that may be taken. These countermeasures include sheltering, evacuation and the consumption of stable ...

International Nuclear Information System (INIS)

A variety of special regulations exist in Costa Rica for registration and transport of hazardous substances; these set the requirements for entry into the country and the security of transport units. However, the regulations mentioned no specific rules for storing hazardous substances. Tax deposits have been the initial place where are stored the substances that enter the country.The creation of basic rules that would be regulating the storage of hazardous substances has taken place through the analysis of regulations and national and international laws governing hazardous substances. The regulatory domain that currently exists will be established with a field research in fiscal deposits in the metropolitan area. The storage and security measures that have been used by the personnel handling the substances will be identified to be putting the reality with that the hazardous substances have been handled in tax deposits. A rule base for the storage of hazardous ...

International Nuclear Information System (INIS)

In Romania, the nuclear power is an element of sustainable development, being competitive, efficient and viable in the market economy. Fuel supply is ensured as nuclear fuel is manufactured in the country out of local uranium resources available in Romania. As for the environmental protection, it is known that, unlike the thermal power plants, the nuclear power plants do not release sulfur and nitrogen oxides, carbon dioxide and do not generate slag and ashes. The operation of nuclear power units does not release pollutants and, accordingly, these stations can contribute to the limitation and the abatement of environmental pollution. After seven years of Cernavoda NPP Unit 1 operation, a facility for storing low and medium level nuclear fuel wastes was built at the plant site as well as an intermediate dry storage for spent nuclear fuel whose first modules were commissioned in July 2003. They shall provide safe storage conditions for nuclear fuel wastes for many decades ahead. After ...

Science.gov (United States)

The Heavy Water Reactor Facility (HWRF), as part of the defense-in-depth philosophy to mitigate the effect of design-basis and severe accidents, is equipped with a passive containment cooling system (PCCS). The function of the PCCS is to provide a safety-grade path to the ultimate heat sink for the removal of the reactor coolant system sensible heat and core decay heat. Ambient air enters an annular space between the steel containment shell and the surrounding concrete shield building through inlets in the shield building wall, is heated via natural convection, rises, and exits the building through a chimney located above the containment dome. A test program is in place to access parameters important to the effective operation of the PCCS. This paper focuses on the large-scale tests (LSTs). The objectives of these tests are as follows: (1) demonstrate natural circulation cooling with more prototypic cylinder and dome surface area ratios than ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a liquid-metal-cooled test reactor located on the Hanford Site. The FFTF is the only reactor of this type designed and operated with the intent of meeting the licensing requirements of the Nuclear Regulatory Commission (NRC). Unique characteristics of the FFTF that present special challenges related to leak rate testing include thin wall containment vessel construction, cover gas systems that penetrate containment, and a low-pressure design basis accident. The successful completion in 1986 of the third FFTF Integrated Leak Rate Test (ILRT) five days ahead of schedule and 10% under budget was a major achievement for the Westinghouse Hanford Company. The success of this operational safety test was due in large part to a special local area network (LAN) of three IBM PC/XT computers that monitored the sensor data, calculated the containment vessel leak rate, and displayed test results. The multiple computer ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion control on gas pipelines plays an important role on the assessment of pipeline integrity and reliability. In many countries a great extension of buried pipelines is used on transport and distribution systems. This extension will be certainly increased in a near future due to the increasing consumption of natural gas. Inadequate corrosion control can drive to pipeline failures, bringing up the possibility of accidents in populated or environmental protected areas, bringing together severe economical, legal and environmental consequences. Corrosion is frequently considered as a natural and inevitable phenomenon. Based upon this assumption, some recommendations are included on design standards of gas pipelines in order to compensate its detrimental effect. The aim of this work is to present a review of the correlation between external corrosion process and the guidelines established during the project phase of gas pipelines. It is ...

International Nuclear Information System (INIS)

ARIES-AT is a 1000 MWe conceptual fusion power plant design with a very low projected cost of electricity. The design contains many innovative features to improve both the physics and engineering performance of the system. From the safety and environmental perspective, there is greater depth to the overall analysis than in past ARIES studies. For ARIES-AT, the overall spectrum of off-normal events to be examined has been broadened. They include conventional loss of coolant and loss of flow events, an ex-vessel loss of coolant, and in-vessel off-normal events that mobilize in-vessel inventories (e.g., tritium and tokamak dust) and bypass primary confinement such as a loss of vacuum and an in-vessel loss of coolant with bypass. This broader examination of accidents improves the robustness of the design from the safety perspective and gives additional confidence that the facility can meet the no-evacuation requirement under average weather conditions. We also provide ...

Energy Technology Data Exchange (ETDEWEB)

In 2004, the Southeastern France regional council asked the regional health observatory to conduct an environmental health inventory to i) identify environmental health problems in this area; ii) examine the relations between environmental exposure to pollutants and human health; and iii) help public officials to identify priorities in this area. We collected and validated data from national, regional and local institutions, constructed environmental (levels of emissions and pollutants), health (mortality, incidence, prevalence) and behavioral indicators (e.g., complaints about odors), and compared these over time and between places when possible. For each topic, we summarized current knowledge about the links between environment and health. In southeastern France, as in other French areas, indoor air pollution, home and leisure injuries and other home-related risks are public health issues. Other topics are more ...

UK PubMed Central (United Kingdom)

This is a retrospective study of the development of the social worker role within the multi-disciplinary team setting of the Accident and Emergency (A&E) Department at Burnley General Hospital...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This document presents an assessment of the severe accident phenomena observed from four Full-Length High-Temperature (FLHT) tests that were performed by the Pacific Northwest Laboratory (PNL) in the National Research Universal (NRU) reactor at Chalk River, Ontario, Canada. These tests were conducted for the US Nuclear Regulatory Commission (NRC) as part of the Severe Accident Research Program. The objectives of the test were to simulate conditions and provide information on the behavior of full-length fuel rods during hypothetical, small-break, loss-of-coolant severe accidents, in commercial light water reactors.

International Nuclear Information System (INIS)

... 5 360 p. RADIATION PROTECTION AND DOSIMETRY fire fighting occupational

International Nuclear Information System (INIS)

The early accident Sequence of the Station Blackout accident is simulated for Daya Bay Nuclear Power Plant, using MELCOR code. The radioactivity of main fission products was derived after calculating the source term in containment. The data will be used for Daya Bay NPP PSA analysis

Energy Technology Data Exchange (ETDEWEB)

DOE installations possessing sufficient quantities of fissile material to potentially constitute a critical mass, such that the excessive exposure of personnel to radiation from a nuclear accident is possible, are required to provide nuclear accident dosimetry services. This document describes the personal nuclear accident dosimeter (PNAD) used by SNL and prescribes methodologies to initially screen, and to process PNAD results. In addition, this report describes PNAD dosimetry results obtained during the Nuclear Accident Dosimeter Intercomparison Study (NAD23), held during 12-16 June 1995, at Los Alamos National Laboratories. Biases for reported neutron doses ranged from -6% to +36% with an average bias of +12%.

Energy Technology Data Exchange (ETDEWEB)

In case of a severe nuclear accident at a PWR plant, countermeasures will be initiated in the short term by authorities to reduce the consequences of the atmospheric radioactive releases on the neighbouring population. Various factors influence the level of protection afforded by countermeasures. For instance, a too late intervention would lead to a Jack of efficiency in terms of dose reduction if the actual evolution of the accident is not considered. Thus, implementation of countermeasures should be optimized. In general, the projected doses (those without countermeasure) are compared with those expected when a particular countermeasure or strategy is implemented. In this paper, an in-depth analysis associates the kinetics of the release with the corresponding evolution of the dosimetric efficiency of countermeasures. This is done at different times in the short term of the accident and for various distances from the ...

International Nuclear Information System (INIS)

Understanding of the thermal hydraulic phenomena is now the key issue in solving the severe accident problems of light water reactors. The Atomic Energy Society of Japan has organized a special committee on the evaluation of the thermal hydraulic phenomena in severe accident. The committee has continued the investigation of present status of thermal hydraulics in severe accident. Industries have completed the detailed implementation of the accident management measures, and industries have established also a self-regulatory document mainly on phase II accident management for the containment design of the future reactors. Present paper reviews the current status of evaluation activity referring to severe accident research in Japan. The phenomena included in this paper are (1) molten core behavior in lower plenum of pressure vessel, (2) fuel-coolant interaction, ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the activities for improving the Probabilistic Safety Assessment (PSA) quality in the human reliability analysis (HRA) of the pre-accident human errors for the Korea Standard Nuclear Power Plant (KSNP). We evaluate the HRA results of the PSA for the KSNP and identify the items to be improved using the ASME PRA Standard. Evaluation results show that the ratio of items to be improved for pre-accident human errors is relatively high when compared with the ratio of those for post-accident human errors. They also show that more than 50% of the items to be improved for pre-accident human errors are related to the identification and screening analysis for them. In this paper, we develop the modeling guidelines for pre-accident human errors and apply them to the auxiliary feedwater system of the KSNP. Application results show that more than 50% of the items to be ...

International Nuclear Information System (INIS)

Full text of publication follows: The hydrogen mitigation system of 20 igniters and 6 PARs is installed to control the hydrogen in the containment during severe accidents and design basis accidents, respectively, in Shin-Wolsung 1 and 2 nuclear power plants. The igniters are primarily installed at the hydrogen source locations, and the PARs are installed in the open spaces. The PARs will maintain the hydrogen concentration within the containment atmosphere below the limit of 4 v/o in accordance with Regulatory Guide 1.7 during design basis accidents. The igniters will maintain the hydrogen concentration within the containment atmosphere below the limit of 10 v/o in accordance with 10CFR50.34(f) during severe accidents. In addition, the PARs can be used as a supplementary means to control the hydrogen concentration during severe accidents because of their inherent passive ...

International Nuclear Information System (INIS)

Construction and commissioning period of NPP are reduced world over drastically by stringent schedule for financial and economic reasons. For meeting the schedule, commissioning of components and systems are started immediate after installation, while construction activities are continued in parallel at the same place. Parallel activities' and 'Time Constraint' have brought new challenges to 'Management of Fire and Industrial Safely' during commissioning. An innovative approach was used during such phase of commissioning of TAPP-3 and 4. This paper outlines challenges encountered during this phase and special approach and measures used to meet those challenges. This paper also outlines problems encountered during implementation of these measures and subsequent change in approach to ensure smooth and safe execution of activities. Primarily, challenges were conflicting requirements by various agencies to carryout commissioning in parallel with construction activities concurrently. Main ...

International Nuclear Information System (INIS)

Korea Atomic Energy Research Institute, using the ANS low power and shutdown (LPSD) probabilistic risk assessment (PRA) Standard, evaluated the LPSD PSA model of the KSNP, Yonggwang Units 5 and 6, and identified the items to be improved. The evaluation results of human reliability analysis (HRA) of the post-accident human errors in the LPSD PSA model for the KSNP showed that 10 items among 19 items of supporting requirements for those in the ANS PRA Standard were identified as them to be improved. Thus, we newly carried out a HRA for post-accident human errors in the LPSD PSA model for the KSNP. Following tasks are the improvements in the HRA of post-accident human errors of the LPSD PSA model for the KSNP compared with the previous one: Interviews with operators in the interpretation of the procedure, modeling of operator actions, and the quantification results of human errors, site visit. Applications of limiting value to ...

Science.gov (United States)

A ground-breaking study was recently completed as part of the Seabrook Level 2 PRA update. This study updates the post-core damage phenomena to be consistent with the most recent information and includes accident management activities that should be modeled in the Level 2 PRA. Overall, the result is a Level 2 PRA that fully meets the requirements of the ASME PRA Standard with respect to modeling accident management in the LERF assessment and NRC requirements in Regulatory Guide 1.174 for considering late containment failures. This technical paper deals only with the incorporation of operator actions into the Level 2 PRA based on a comprehensive study of the Seabrook Station accident response procedures and guidance. The paper describes the process used to identify the key operator actions that can influence the Level 2 PRA results and the development of success criteria for these key operator actions. This addresses a key ...

International Nuclear Information System (INIS)

A lot of recent experimental results show that cladding failure limits to the RCCA ejection accident will be changed because of the impact of the high irradiation on the fuel rod behavior in the reactor. The maximal assembly discharge burnup in Daya Bay unit 1 and 2 will reach up to 52 GMd/tU with 18 month fuel cycle. It is necessary to perform the specific RCCA ejection accident analysis for the high burnup fuel assembly in order to evaluate the maximal enthalpy in the fuel rods. There is no definite design limit of maximal enthalpy for high burnup assembly during the RCCA ejection accident. One could perform the rod ejection accident analysis for the high burnup assemblies and compare the analytical results with the specific experimental results. The RCCA ejection accident analysis for the high burnup assemblies for Daya Bay NPS has been performed based on the conventional ...

International Nuclear Information System (INIS)

The Food Safety and Inspection Service (FSIS) of the United States Department of Agriculture (USDA) inspects domestic and imported meat and poultry food products to assure the public that they are safe, wholesome, not economically adulterated and properly labeled. The Service also monitors the activities of meat and poultry plants and related activities in allied industries, and establishes standards and approves labels for meat and poultry products. As part of its responsibility, shortly after the Chernobyl accident occurred, FSIS developed a plan to assess this accident's impact on domestically produced and imported meat and poultry

International Nuclear Information System (INIS)

The potential public safety impacts from accidents in conceptual fusion power plants were investigated. Fusion was found to have some potential for accidents, as does any energy generating system. Functions of fusion power plants were identified that possess sufficient potential for an accidental release of toxic materials to the environment. An assessment was made of the impact of the potential accidents and recommendations are included for R and D that will allow incorporation of safety concerns in fusion power plant design. This work was based on a review of information available in conceptual design documents of fusion reactor systems.

International Nuclear Information System (INIS)

The authors suggested a conceptual model of automatic processing the data on radioactive environment contamination (REC) after the accidents at the plants with nuclear fuel cycle. The possibilities of mathematic methods of processing the data on REC in automatic-control systems of radiation situation. It is stated that the following 2 methods most of all satisfy the existing requirements: linear interpolation on the locally homogenous fields and successive parametric adaptation. As an example there are demonstrated the results of estimation of the actual radiation situation in the region of accident at Siberian Chemical Plant (town Tomsk-7) in April, 1993. 6 refs.; 2 figs.

UK PubMed Central (United Kingdom)

This paper attempts to clarify the most common measures available for the fire and electrical engineer in the prevention of polychlorinated biphenyl (PCB) hazards. It points out the risks and the potential...Full Text Available

Science.gov (United States)

... Except for isolated radiation accidents over the ensuing years, little practical experience has been gained in the treatment of thermal injuries ...

UK PubMed Central (United Kingdom)

During a high speed road traffic accident, a 26-year-old man suffered multiple fractures of his thoracic vertebrae and bilateral pneumothoraces. The day after admission and commencement of nasogastric...Full Text Available

International Nuclear Information System (INIS)

Korea Atomic Energy Research Institute, using the ANS Low Power /Shutdown (LPSD)PRA Standard, evaluated the LPSD PSA model of the KSNP, Younggwang (YGN) Units 5 and 6, and identified the items to be improved. The evaluation results of human reliability analysis (HRA) of the pre-accident human errors in the LPSD PSA model of the KSNP showed that 13 items among 15 items of supporting requirements for those in the ANS PRA Standard were identified as them to be improved. Thus, we newly carried out a HRA for pre-accident human errors in the LPSD PSA model for the KSNP to improve its quality. We considered potential pre-accident human errors for all manual valves and control/instrumentation equipment of the systems modeled in the KSNP LPSD PSA model except reactor protection system/ engineering safety features actuation system. We reviewed 160 manual valves and 56 control/instrumentation equipment. The number of newly identified ...

International Nuclear Information System (INIS)

During the last years one focus of German PWR safety analysis was boron dilution events with the potential of reactivity transients. Coolant with a low boron concentration could be collected in localized areas of the reactor coolant system e.g. by separation of borated reactor coolant into highly concentrated and diluted fractions (inherent dilution) which can occur during reflux- condenser heat transfer after a small break loss of coolant accident with a limited availability of the emergency core cooling systems. The TUeV NORD SysTec was charged by German supervisory authorities with the assessment of the safety analyses of boron dilution events presented by the utilities. These analyses are based on the simulation of boron dilution and transport processes in conjunction with a number of dedicated experiments. The analyses shall demonstrate that boron dilution events cannot lead to recriticality of the core. Hence the boron concentration at ...

Energy Technology Data Exchange (ETDEWEB)

In the case of a serious accident and as a precautionary measure, several protection actions can be implemented by the prefect during the emergency phase. In France the levels of intervention are given by a ministerial decree of the 13. october 2003, resuming recommendations of the International Atomic Energy Agency. The selected values are: an efficient dose of 10 mSv for the stake under cover and in the listening: the concerned persons have to put under cover in a building, any openings carefully closed and stay in the listening of the orders of the prefect; an efficient dose of 50 mSv for evacuation; an efficient dose to the thyroid of 100 mSv for the taking of stable iodine tablets. In order to help the authorities to choose between the keeping of populations at their place or immediate evacuation the decision criteria are: if the forecasted efficient dose of the first month is under 1 mSv, the populations stay in place; if the forecasted efficient dose is ...

Science.gov (United States)

The Army Reactor Area (ARA) II was constructed in the late 1950s as a test site for the Stationary Low Power Reactor No. 1 (SL-1). The SL-1 was a prototype power and heat source developed for use at remote military bases using a direct cycle, boiling water, natural circulation reactor designed to operate at a thermal power of 3,000 kW. The ARA II compound encompassed 3 acres and was comprised of (a) the SL-1 Reactor Building, (b) eight support facilities, (c) 50,000-gallon raw water storage tank, (d) electrical substation, (e) aboveground 1,400-gallon heating oil tank, (f) underground 1,000-gallon hazardous waste storage tank, and (g) belowground power, sewer, and water systems. The reactor building was a cylindrical, aboveground facility, 39 ft in diameter and 48 ft high. The lower portion of the building contained the reactor pressure vessel surrounded by gravel shielding. Above the pressure vessel, in the center portion of the building, was a turbine generator ...

International Nuclear Information System (INIS)

In the present paper, experimental study of forced convection boiling were performed to investigate the post-CHF characteristics of a vertical annular channel with one heated rod and four spacer grids for new refrigerant R-134a. The experiments were conducted under outlet pressure of 11.6, 13, 16 and 20 bar, mass fluxes of 100-600 kg/m2s, and inlet temperatures of 25-51 .deg. C. The parametric trend of the post-CHF data was well consistent with previous studies. The two phase flow regime in tube flow occurring downstream of the CHF has been called post-CHF, dispersed flow, liquid-deficient flow, mist flow and film boiling. This regime is characterized by a continuous vapor phase with discrete liquid drops and a non-wetted heated surface. This regime has a considerable importance in the areas of light water reactor(LWR) accident analysis and other film boiling applications. The post-CHF region occurs by design in heat exchangers operating in the ...

International Nuclear Information System (INIS)

Steam generators (SG) are among the most critical components of pressurized water Nuclear Power Plants (NPP). SG tubes must provide a reliable pressure boundary between the primary and secondary cooling water. It is because that any leakage from tube defects could result in the release of radioactivity to the environment. Thus degradations of steam generators tubes should be monitored and inspected periodically under nuclear regulatory. In-service inspections of SG tubes are carried out using eddy current test (ECT) and the defected tubes are usually plugged. Because the radioactivity in the internal of SG chambers limits free access of human worker, remote manipulators are required. In South Korea, Manipulators such as the Zetec SM series and the Westinghouse ROSA series have been used. Such manipulators are rigidly mounted to manways or tube sheets of SG. Confusions for the inspected tubes may occur from deflection of the manipulators. To reduce the deflections of the manipulators ...

Energy Technology Data Exchange (ETDEWEB)

Following the Chernobyl accident of April 1986, there has been a continual increase in the numbers of reported cases of childhood thyroid carcinoma. An EC-supported consortium to study the pathology and molecular biology of the thyroid cancers is being coordinated from the University of Cambridge. This paper reports the findings of this study so far, together with its recommendations for further studies. (author).

International Nuclear Information System (INIS)

In Aug 2002, the National Nuclear Safety Administration of China issued the policy statement for building new nuclear power plants, which requires the probability based safety goal of severe core damage must be lower than 10"-"5/a. The station blackout accident would be possible to cause a severe accident if there were no effective engineering measures to prevent or mitigate the consequences of the accident. By using MELCOR1.8.5 and KORIGEN codes, the present paper has simulated the station blackout accident for Daya Bay Nuclear Power Plant and calculated the source term and radioactivity of main fission products in the containment in the late phase of the accident. CsI is found the main part of aerosol in the containment. The Xe133 and Xe133m start releasing from the containment after its failure, and the upper limit of the amount of released radioactivity is evaluated less than ...

International Nuclear Information System (INIS)

The volume contains reports on plant technology, on systems organisation with the aim to minimize the risk (human error), on the problem of seismic risk, on core-disruptive accidents and on accident consequence models with different release categories and a comparison of the potential damage incurred. Mr. Webb; one of the authors, attempts to disprove the objections to his two earliest SNR statements by experts of Karlsruhe Nuclear Research Centre. (AK).

International Nuclear Information System (INIS)

Requirements and guidance are provided for a quality assurance program for the design of nuclear fuel reprocessing facilities involving structures, systems and components whose satisfactory performance is required to prevent accidents that could cause undue risk to the health and safety of the public, or to mitigate the consequences of such accidents if they were to occur. The standard is to be used in conjunction with ANSI N46.2.

Energy Technology Data Exchange (ETDEWEB)

The management procedure of a large PRISE (Primary-to-Secondary) leakage accident at Loviisa nuclear power plant taking into account the plant modifications which are expected to be realized during 1995-96 is described. The management procedure has been validated by performing thermal hydraulic analyses with the computer code RELAP5/MOD3 and the results from these analyses are also shortly discussed. (4 refs., 6 figs., 1 tab.).

UK PubMed Central (United Kingdom)

We report for the first time a case of a 54 years old man with a fatal motorcycle accident due to an external bleeding compression of left internal mammary artery graft to the left anterior descending...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The objectives of this project to interface the site-specific real-time radiological dose assessment system FADAS(Following Accident Dose Assessment System) to CARE. In this study, the results of the field tracer experiments conducted on the Younggwang site have been analysed. And the experimental procedure on Ulchin site has been introduced. The environmental characteristics on Ulchin and Wolsung has been investigated.

Energy Technology Data Exchange (ETDEWEB)

In developing severe accident management strategies, an engineering decision would be made based on the available data and information that are vague, imprecise and uncertain by nature. These sorts of vagueness and uncertainty are due to lack of knowledge for the severe accident sequences of interest. The fuzzy set theory offers a possibility of handling these sorts of data and information. In this paper, the possibility to apply the decision-making method based on fuzzy set theory to the evaluation of the accident management strategies at a nuclear power plant is scrutinized. The fuzzy decision-making method uses linguistic variables and fuzzy numbers to represent the decision-maker's subjective assessments for the decision alternatives according to the decision criteria. The fuzzy mean operator is used to aggregate the decision-maker's subjective assessments, while the total integral value method is used ...

International Nuclear Information System (INIS)

The report presents the results of the study carried out to estimate the accident risk involved in the transport of spent fuel from Rajasthan Atomic Power Station near Kota to the fuel reprocessing plant at Tarapur. The technique of probabilistic safety analysis is used. The fuel considered is the Indian pressurised heavy water reactor fuel with a minimum cooling period of 485 days. The spent fuel is transported in a cuboidal, naturally-cooled shipping cask over a distance of 822 km by rail. The Indian rail accident statistics are used to estimate the basic rail accident frequency. The possible ways in which a release of radioactive material can occur from the spent fuel cask are identified by the fault tree analysis technique. The release sequences identified are classified into eight accident severity categories, and release fractions are assigned to each. The consequences resulting from the release ...

International Nuclear Information System (INIS)

An uncertainty decrease is an very important issue for enhancing risk-informed (RI) activities worldwide. Especially, a relatively large uncertainty in a level-2 (L2) PSA risk compared with level-1 internal PSA risk has been a bottleneck problem in the RI application to the extent of a severe accident management. According to the ASME PRA standard in which sources of an uncertainty to capture a category-II RI (= Option 2) capability are listed, an uncertainty analysis which identifies the key sources of an uncertainty and includes sensitivity studies for dominant contributors to LERF (Large Early Release Frequency) needs to be provided. To solve these problems, USNRC have developed the 'SPAR-LERF' model related to the L2 RI application and 'L2 uncertainty assessment and improvement' work is being taken as a main PSA2 topic of the SARNET (Severe Accident Research Network of Excellence) program in Europe by OECD/NEA. Domestically, a mid/long-term ...

Science.gov (United States)

This report summarizes the results of an expert-opinion elicitation activity designed to qualitatively assess the status and capabilities of currently available computer codes and models for accident analysis and reactor safety calculations of advanced sodium fast reactors, and identify important gaps. The twelve-member panel consisted of representatives from five U.S. National Laboratories (SNL, ANL, INL, ORNL, and BNL), the University of Wisconsin, the KAERI, the JAEA, and the CEA. The major portion of this elicitation activity occurred during a two-day meeting held on Aug. 10-11, 2010 at Argonne National Laboratory. There were two primary objectives of this work: (1) Identify computer codes currently available for SFR accident analysis and reactor safety calculations; and (2) Assess the status and capability of current US computer codes to adequately model the required accident scenarios and associated phenomena, and ...

International Nuclear Information System (INIS)

Stable boiloff of core water during a severe LWR accident, that is, boiloff driven only by the decay power generated below the water level, is tractable analytically and is relatively insensitive to axial power distribution. As might be expected, calculated accident event times are sensitive to the fidelity of the decay power model. During later stages of boiloff, heat transfer or transport of energy from above the water level to the residual water can result in an unstable condition during which the boiloff rate increases greatly. The unstable boiloff phenomenon illustrates the highly nonlinear influence of core heat transfer during meltdown and emphasizes the great accuracy requirements which attend the modeling of the accident during periods of enhanced heat transfer when significant zirconium oxidation is possible.

British Library Electronic Table of Contents (United Kingdom)

Abstract:- Two motorcycle riders lost control of their vehicle, fell, and hit a guardrail, which acted as a blade and led to a rapid, fatal outcome. In one case, the high velocity of the body at the time of the impact resulted in complete detachment of the trunk. Reconstruction of the accident dynamics enabled the guardrail post to be identified as the means of injury in both cases. The two accidents occurred over a short period of time, highlighting a dangerous phenomenon that in less severe cases is presumably associated with different degrees of survivor disability. The accidents deserve mention, because a different design of the impact surface of the guardrail post might have prevented the lethal outcome. There is an urgent need for legislators to pass regulations that modify crash bar...

International Nuclear Information System (INIS)

SAMPSON is an integration of twelve analysis modules under the final development phase (phase-2) and will be capable of simulating hypothesized severe accidents in a nuclear power plant. One of these modules, the Molten Core Relocation Analysis (MCRA) module, simulates the relocation behavior of a molten core during a severe accident. MCRA models severe accident phenomena by using mechanistic formulations for multi-phase, multi-component, and multi-velocity field. As one of the verification studies of SAMPSON in Phase-1, the in-core phenomena of PHEBUS/FPT0 was analyzed with three modules, MCRA, fuel rod heat up analysis (FRHA) module, and the analysis control module (ACM) of SAMPSON. (author)

International Nuclear Information System (INIS)

In view of the persisting and understandable fear of parents with regard to radioactivity in the food of their babies as a consequence of the Chernobyl reactor accident, the Commission on Nutrition of the Deutsche Gesellschaft fuer Kinderheilkunde (German Society of Pediatrics) and the Strahlenschutzkommission have published a statement. According to this statement, the maximum permissible level of radioactivity in commercial baby food has been fixed by the EC to be 370 Bq/kg. The dietetic food industry itself has fixed a maximum for its products which is only a tenth of the radioactivity level permitted by the EC directive. The milk powders for infants tested since the reactor accident contained no measurable radioactivity or only very low amounts of Cs 134 or Cs 137, correspondung to a maximum of 25 Bq/kg in the product. Late damage to health is not to be expected. (orig./ECB).

Energy Technology Data Exchange (ETDEWEB)

The 200 Area Interim Storage Area Technical Safety Requirements define administrative controls and design features required to ensure safe operation during receipt and storage of canisters containing spent nuclear fuel. This document is based on the 200 Area Interim Storage Area, Annex D, Final Safety Analysis Report which contains information specific to the 200 Area Interim Storage Area.

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: A porous media solution PORFLO has been developed for the 3-dimensional two-phase flow by describing the process facility in Cartesian or cylindrical coordinates. The local porosity fraction is applied for distinguishing the fluid filled volumes from the solid structures. The solid structure contribute the two-phase flow through the wall friction, flow area and heat transfer. Optionally the solid structure may contain primary liquid of steam generators, steam in the higher temperature and pressure to be condensed or electrical heating power. By using these optional boundary conditions three different process facilities have been analysed. The thermohydraulic solution based on 5-equation approach, where the conservation equations are solved for the liquid and gas (vapour) mass, mixture momentum (giving the velocity only for the mixture), liquid and gas energy, is described shortly. In addition to that the principles modelling ...

UK PubMed Central (United Kingdom)

Thus far there are relatively few data on the risk of leukemia among those who were exposed to external radiation during cleanup operations following the Chornobyl nuclear accident, and results...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The motto of the U.S. Coast Guard, Semper Paratus (Always Ready), should resonate strongly with those of us in the health and safety business, because we must also be ready to deal with a variety of possible radiation accidents that could occur at any time.

UK PubMed Central (United Kingdom)

BackgroundAlthough some previous studies have suggested that posttraumatic growth (PTG) is comprised of several factors with different properties, few have examined both the association...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

NUPEC has carried out hydrogen mixing tests to investigate hydrogen distribution behavior within a model containment and to provide a set of experimental data for validation of severe accident analysis codes.

UK PubMed Central (United Kingdom)

Blunt chest-wall trauma is common; however, resultant tricuspid valve rupture is rare and can be subtle in its presentation. Transthoracic echocardiography plays a key role in diagnosis.Herein,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This guidebook organizes the profusion of rules and regulations surrounding radiation protection into a single-volume reference. Employee and public protection, accident prevention, and emergency preparedness are included in this comprehensive coverage. Whenever possible, information is presented in convenient checklists, tables, or outlines that enable you to locate information quickly.

Energy Technology Data Exchange (ETDEWEB)

This article, published in issue 80 of 'l'ACROnique du nucleaire', aims to retrace the early steps in the consideration of the possibility of a nuclear accident in France, with the inclusion of 'non-institutional' participants and applying the lessons learned in Belarus in the contaminated territories around the Chernobyl nuclear power plant. After a review of the origin of the involvement of the Association pour le Controle de la Radioactivite dans l'Ouest (ACRO) in addressing post-accident issues alongside the populations living in an environment polluted by radioactivity, it discusses, from the critical viewpoint of an NGO, the context and the working method adopted for this examination. This is followed by some key elements of the programme and unresolved questions about the available body of knowledge which motivates research and about the method adopted for the work. The conclusion, ...

International Nuclear Information System (INIS)

The major feed-water line break accident is re-analyzed, which is based on Guangdong Daya Bay nuclear power station final safety analysis report, to justify the impacts of the decreasing of auxiliary feed-water flow rate on the safety margin in Daya Bay. The results showed that the accident analysis can meet the demands of acceptance criteria with the auxiliary feed-water flowrate decreasing from 45 m"3/h to 41.8 m"3/h, and enough safety margin is still retained

International Nuclear Information System (INIS)

An experimental technique is described which allows for parametric investigations of transient behavior of mobile core materials in a fuel bundle geometry. For the out-of-pile simulation of energy releases resulting from mild TOP- or LOF-accidents the exothermic reaction of an aluminium-oxide-thermite is used. Transient material relocation inside the test section is recorded by X-ray-cinematography. Results of some experiments recently performed close to conditions expected to be achieved during mild TOP-accidents are described in detail.

International Nuclear Information System (INIS)

Within the APROS simulation environment we have built a thermo-hydraulic model of a conceptual fusion power plant which is water cooled and uses lithium-lead for tritium breeding. For the safety assessment of this design we have studied an accident sequence which starts from a loss or coolant flow then leads to first wall breach and pressurisation of the vacuum vessel. Simulations have revealed strong pressure transients which can be alleviated by design changes. One goal is to verify the adequacy of the containment design: it remains intact at least 14 h without any mitigating efforts. Estimates for radioactive releases are obtained. (author)

Energy Technology Data Exchange (ETDEWEB)

This document contains the accident sequence analysis of internally initiated events for Grand Gulf, Unit 1 as it operates in the Low Power and Shutdown Plant Operational State 5 during a refueling outage. The report documents the methodology used during the analysis, describes the results from the application of the methodology, and compares the results with the results from two full power analyses performed on Grand Gulf.

International Nuclear Information System (INIS)

A semi-mechanistic model for calculating solid radionuclide release rates from bubbling pools of sodium was developed. The influence of particle spacial and size distributions on the decontamination of the releases was analysed and found significant. Decontamination factors are shown as a function of pool depth, bubbling characteristics and particle size distribution. The calculation of a decontamination factor for estimating the source term of large scale hypothetical core disruptive accidents is presented. The decontamination factor for a large scale accident was found to be two orders of magnitude greater than results obtained from small scale experiments conducted with uniform particle distributions. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Short communication

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

On 21 October 1994, three brothers entered a waste repository at Tammiku, Estonia, without authorization and removed a metal container enclosing a caesium-137 source. During the removal the source was dislodged and fell to the ground. One of the men picked up the source, placed it in his pocket and took it to his home in the nearby village of Kiisa. Very soon after entry into the repository he began to feel ill, and few hours later he began to vomit. The man was subsequently admitted to hospital with severe injuries to his leg and hip and died on 2 November 1994. The injury and subsequent death were not attributed to radiation exposure, and the source remained in the man's house with his wife and stepson and the boy's great-grandmother. The boy was hospitalized on 17 November with severe burns on his hands, and these were identified by a doctor as radiation induced. The authorities were alerted, and the Estonian Rescue Board recovered the source from the house. The source was returned ...

International Nuclear Information System (INIS)

In this paper a comparison between severe accident calculations performed for a WWER 1000 with the ASTEC1.1v0 and MELCOR 1.8.5 computer codes for a small break LOCA (ID 60 mm) without intervention of hydro accumulators is presented. This investigation has been performed in the framework of the SARNET project under the EURATOM 6th framework program. Once the accident sequence scenario is specified, both codes (MELCORE and ASTEC) are able to determine the core and containment damaged states, to estimate the release of radionuclides from the fuel as well as from the primary circuit and containment. Theses results are used to estimate the maximum period of the time during which the personnel could still take particular decisions in order to mitigate such an accident. The aim of the performed analysis is to estimate the discrepancy between ASTEC and MELCORE 1.8.5 calculations. Such discrepancies will be studied, if the case, ...

International Nuclear Information System (INIS)

In areas where radiation dose monitoring has not been performed, it is essential to use material available in the environment be able to rapidly assess doses to individuals for immediate emergency medical care or for general estimation of the radiological consequences. It was shown that certain types of telephone cards containing microchips have the potential to be used as individual radiation dosimeters in emergency situations to detect doses over 250 mGy by luminescence measurements. In order to understand the dosimetric properties of chip cards, the components obtained from INFINIEON Company at various stages of production were used for luminescence measurements. It is found that the protecting layer used above the chips so called 'globe top' is the main source of radiation induced signal in chip cards. The globe top produced by INFINIEON at that stage is found to contain SiO2 and Epoxy. In order to improve the dosimetric properties of the chip cards, the raw ...

Energy Technology Data Exchange (ETDEWEB)

On March 28, 1979, the Pennsylvania Three Mile Island nuclear power plant Unit 2 (TMI-2) suffered a partial fuel-melt accident. During this accident, over 20,000 lb of molten fuel flowed through holes melted through the baffle plates and through the lower-core support assembly (LCSA). The molten fuel subsequently resolidified in the bottom of the reactor vessel. The lower-core support assembly of the TMI-2 reactor was not structurally damaged during the accident. In order to permit defueling of that region of the core, the LCSA was cut to permit access. A five-axis teleoperator was developed to deliver plasma arc cutting, rotary grinding and abrasive waterjet cutting of end effectors to the LCSA. Complex geometry sectioning was completed in a mock-up facility at chemistry and pressure conditions simulating those of the vessel, prior to actual in-vessel operations. In-vessel activities began in early May 1988 and were ...

Energy Technology Data Exchange (ETDEWEB)

The RADionuclide Transport, Removal, And Dose (RADTRAD) code is designed for US Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the offsite population and to control room operators following a design-basis accident at Light Water Reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465, ``Accident Source Terms for Light-Water Nuclear Power Plants.`` The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different ...

International Nuclear Information System (INIS)

The paper discusses the safety problems connected with the conversion to dense storage of RBMK-1000 spent fuel in reactor cooling pools and independent storage facilities. Recourse to dense storage has been made for a number of reasons, among which are the absence of spent fuel shipments from the nuclear power plant site, prolongation of storage time and a partial change in storage conditions. Increasing the storage density per unit volume of the storage facility and turning to new technical procedures (as against the basic design) call for further investigation of safety problems. The safety assessment of the dense storage mode includes: (1) Selecting a list of initiating events for design basis and unforeseeable accidents; (2) Assessing dense storage safety under normal as well as design basis accident conditions; (3) Safety analysis and development of measures to compensate for unforeseen accidents. Based on the studies ...

Energy Technology Data Exchange (ETDEWEB)

Analyses have been performed of the potential consequences to the public of hypothetical loss-of-coolant accidents in conceptual fusion power plant designs. In order to establish upper bounds to the consequences of such events, a case has been studied in which total loss of all active cooling has been assumed, with no remedial intervention for the duration of the accident sequence. The analyses are based on three conceptual power plant designs, two of them similar to those assumed in the earlier safety and environmental assessment of fusion power (SEAFP) study (Raeder et al., 1995), with updating of assumed structural materials. The three models studied provide a broad range of design options. In all cases the decay-heat driven temperature transients are well below the level at which structural melting would begin. Based on conservative assumptions, mobilisation, release and dose calculations show that potential maximum doses to the public are ...

Energy Technology Data Exchange (ETDEWEB)

Use of hydrogen in large scale applications is more usual than public is mentioning normally. Nevertheless reserve against hydrogen can be observed up to highest level decision-makers. Possibly a main reason can be found and eliminated by fixing: Some spectacular accidents happened in the past and found great interest. The publication of impressive accidents and the follow up of the events course was very carefully. The research in finding causalities in former decisions and follow up was not in the interest of some people or institutions. Important facts are even not noticed by insiders, but would have been very important for future decision makings and public acceptance of new applications. It will be demonstrated in three historical examples. Much more examples would be available and each one could help to find new applications for a saver and effective use of hydrogen in power supply. Awaking from new reserves could be avoided. Additional a ...

Energy Technology Data Exchange (ETDEWEB)

The Feedwater System supplies feedwater to the steam generator at the required pressure, temperature and flow rate during the plant start-up, normal power operation, shutdown. When the Feedwater System is inoperable or unavailable, the Auxiliary Feedwater System supplies emergency feedwater to the steam generator. If main steam line break occurs, the increase of feedwater flow rate of the faulted steam generator due to decrease of the pressure in the faulted steam generator results in adverse effects in aspect of overcooling the Reactor Coolant System and increased containment pressure/temperature. To optimize the containment mass/energy analysis, this paper evaluates the maximum feedwater and auxiliary feedwater flow rate delivered to the faulted steam generator at each stage of pressure decrease in the faulted steam generator after a main steam line break accident. Calculated Feedwater flows are applied to calculate mass and energy release following MSLB ...

International Nuclear Information System (INIS)

The program package COSYMA for assessing the radiological and economic consequences of nuclear accidents, developed with the support of the European Commission, was applied to investigate the health effects and risks from accidental releases of radioactive material from the Daya Bay nuclear power plant. Population distribution data in the range of 80 km around the site and hourly meteorological data for the year 1985 representative of accident consequence analysis were used. The results showed that early effects are more important at distances closer to the site, while the number of fatal cancers is closely related to the population density and the late effects are still important at distances larger than 50 km from the site. The mean annual expected values for early mortality and late mortality estimated for the population within a circle of 80 km around the Daya Bay nuclear power plant are 4.5x10"-"3 and 0.1 yr"-"1, respectively.

International Nuclear Information System (INIS)

This standard provides requirements and guidelines for installation, inspection and testing activities that assure the quality of important mechanical parts of a nuclear power plant not covered by the ASME Boiler and Pressure Vessel Code, Section III, during construction. These parts include those mechanical systems and components whose satisfactory performance is required: for the plant to operate reliably; to prevent accidents that could cause undue risk to the health and safety of the public; or to mitigate the consequences of such accidents if they were to occur. The requirements of this standard deal with the protection and control necessary to assure that the requisite quality of those important parts of the plant are preserved from the time items are removed from storage or receiving until they are incorporated into the plant up to but not including fuel loading for PWR plants and the completion of cold functional testing for BWR and ...

Energy Technology Data Exchange (ETDEWEB)

The probability of damage and the potential resulting hazards are analyzed for a representative rail shipping container for three severe rail accident scenarios. The scenarios are: (1) the rupture of closure bolts and resulting opening of closure lid due to a severe impact, (2) the puncture of container by an impacting rail-car coupler, and (3) the yielding of container due to side impact on a rigid uneven surface. The analysis results indicate that scenario 2 is a physically unreasonable event while the probabilities of a significant loss of containment in scenarios 1 and 3 are extremely small. Before assessing the potential risk for the last two scenarios, the uncertainties in predicting complex phenomena for rare, high- consequence hazards needs to be addressed using a rigorous methodology.

International Nuclear Information System (INIS)

Through an international collaborative effort, a special version of the CONTAIN code is being developed for integrated mechanistic analysis of the conditions in liquid metal reactor (LMR) containments during severe accidents. The capabilities of the most recent code version, CONTAIN LMR/1B-Mod.1, are discussed. These include new models for the treatment of two condensables, sodium condensation on aerosols, chemical reactions, hygroscopic aerosols, and concrete outgassing. This code version also incorporates all of the previously released LMR model enhancements. The results of an integral demonstration calculation of a sever core-melt accident scenario are given to illustrate the features of this code version. 11 refs., 7 figs., 1 tab.

International Nuclear Information System (INIS)

Dr. Rudolf Schulten of West Germany and expert witnesses from national laboratories, utilities, and the nuclear industry testified on reactor safety issues as they relate to the Chernobyl accident and public concern that modern technology has not paid enough attention to public safety. Each of the witnesses contributed safety-related information based on what has been learned from the Soviet incident. Particular focus went to similarities and differences between the Chernobyl and US reactors in safety design and engineering and to the environmental effects of the accident. The N reactor near Richland and a commercial reactor at Fort St. Vrain, Colorado are the only two operating graphite reactors, but neither is a boiling water reactor.

International Nuclear Information System (INIS)

The present paper deals with the experimental determination of pressure drop across a four-cusped vertical channel. This geometry represents, ideally, the blockage condition in a typical pressurized water reactor with core degraded by accident. Experiments were performed for both single and two-phase flow. Water was utilized for the single-phase measurements whilst simultaneous flow of air and water simulated the steam-water flow. Observation of the prevailing two-phase flow regime was carried out, so that its mechanism could be fully understood. The averaged void fraction was also measured, by the gamma-ray attenuation technique. A wide range of water and air mass flow rates was covered, so that all flow conditions, possible to exist in a reactor with LOCA, could be investigated. New correlations for pressure drop are proposed. (Author).

International Nuclear Information System (INIS)

Integrated Leakage Rate Test (ILRT) of containment system plays a very important role in safety of a Nuclear Power Plant. Containment system constitutes the last physical barrier to release of radioactivity from the core and is called upon to mitigate the consequences of not only accidents within the design basis, but also some of the highly unlikely severe accidents. Hence, leak tightness of containment becomes uttermost priority for the safety of plant personnel and public. The containment and associated ESFs are tested before the first criticality and there after periodically during service. The pre-operational integrated leakage rate is carried out at LOCA based design pressure, at periodic test pressure and at some intermediate pressure points to assess the leakage characteristics. This paper summarizes the various requirements and activities relevant to the ILRT of the Indian Pressurized Heavy Water Reactor (PHWR) containment system. ...

Energy Technology Data Exchange (ETDEWEB)

Possible accident scenarios for a fusion reactor include breaches in the vacuum or cooling system. Intruding air or steam could react with structural or plasma facing materials, possibly mobilizing radioactive isotopes. Safety assessments must consider the early dose at the site boundary from the release of these activated materials. Previous calculations have indicated that cobalt isotopes dominate dose calculations for designs using stainless steel. Values used in these calculations, however, had been largely determined by the measurement limits of the chemical analysis methodology instead of measured releases. The purpose of the current study was to refine the analytical method to reduce the limit for detecting cobalt, and then test PCA steel in air and steam between 973 and 1473 K. Goals were to obtain more accurate measurements of cobalt mobilization in terms of g/m{sup 2}{center_dot}h and insight into the mobilization mechanisms.

Energy Technology Data Exchange (ETDEWEB)

This association participated in different working groups: North Cotentin radioecology group, groups of expertise on the uranium mines of Limousin, executive committee for the management of the post accidental phase of a nuclear accident or a radiological emergency situation, radioactive waste management, radiological surveillance of the territory, radiation protection mission by the Asn, radiological surveillance of the environment of the Chinon nuclear power plant, study of the presence of {sup 235}U around the site of Brennilis, study of the radioactive waste management at the Manche plant, radiological surveillance of the Cyceron cyclotron at Caen, Aurengo commission on the consequences in France of the Chernobylsk accident. Actions of information, regular publications, meeting with public are also a part of the work of this association. (N.C.)

International Nuclear Information System (INIS)

The term 'Post-CHF' was generally used in the two-phase flow regime in tube flow occurring downstream of the CHF. It has various other names such as dispersed flow, liquid-deficient flow, mist flow and film boiling because the two-phase regime is characterized by a continuous vapor phase with discrete liquid drops and a non-wetted heated surface. The regime has been adopted in a lot of applications including nuclear power plants, fossil power plants, steam generators, refrigeration systems and spray cooling, In particular, this regime has a considerable importance in the areas of light water reactor(LWR) accident analysis (off-normal operating conditions) and design in heat exchangers operating in the once-through mode where subcooled liquid enters the exchanger and superheated vapor exits. Recently, innovative PWRs adopt very high power density increases and so require increased safety margins. For instance, advanced PWRs would be going to use ...

International Nuclear Information System (INIS)

Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.

International Nuclear Information System (INIS)

The possibility of using Direct Flow Control (DFC) to avoid catastrophic accidents due to containment breaches in chemical plant is discussed. Recommendations are made for locating fluidic elements, and the effectiveness of simple DFC protection is analysed. More powerful methods of protection are outlined using spin diversion and the complementary properties of fluidic and conventional valves are exploited. (author).

International Nuclear Information System (INIS)

The petroleum and petroleum products increase offer a real development opportunity to the alternative fuels. In the context of the french energy accounting increase, the energy independence notion incites the government to promote these new fuels. If the LPG seems declining because of the accident risks fear, the fuel cell is not for today. Near these two sectors what is the future of the biofuels and the natural gas vehicle or the electric cars? (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

This document presents the analysis of the simulation of the loss of coolant accident at uprate power conditions, that is 2027 MWt (105% of the current rated power of 1931MWt). This power was reached allowing an increase in the turbine steam flow rate without changing the steam dome pressure value at its rated conditions (1020 psiaJ. There are also presented the results of the simulation of the main steam isolation va/ve transient at overpressure conditions 1065 psia and 1067 MWt), for Laguna Verde Nuclear Power Station. Both simulations were performed with the best estimate computer code TRA C BF1. The results obtained in the loss of coolant accident show that the emergency core coolant systems can recover the water level in the core before fuel temperature increases excessively, and that the peak pressure reached in the drywell is always below its design pressure. Therefore it is concluded that the integrity of the containment is not ...

International Nuclear Information System (INIS)

'Small radioactive source results in big accident' have occurred repeatedly in China and worldwide alike. Radioactive source management is one of the key activities for a nuclear power plant to maintain its good safety record and image to the public. From aspects of establishing the management system, centralized storage, periodic accounting, performing whole process control to the source usage and experience feedback etc., the author reports the practice and experience of radioactive source management in Daya Bay Nuclear Power Plant

International Nuclear Information System (INIS)

Since 1945, more than 1.8 x 10"2"1 Bq of artificial radionuclides have been released into the atmosphere. Approximately 2.04 x 10"1"8B, i.e. approx. 0.11%, are the result of accidents at nuclear industrial facilities. This percentage is causing increased interest among researchers. This is due to the fact that in the wake of accidental release radionuclides become distributed unevenly across the Earth's surface, and the associated exposures, fluctuating from background level to several grays, an induce both stochastic and deterministic effects in the irradiated population. A comparative analysis of the medical consequences of the twentieth century's most serious nuclear events, namely the authorized dumping of high level radioactive waste into the river Techa in 1950, the explosion of a storage tank containing long lived radioactive waste in the Southern Urals in 1957, the fire at Sellafield in 1957 and the accident at the Chernobyl nuclear ...

International Nuclear Information System (INIS)

In the case of a release of residual power and fragmenting following a hypothetical accident the applied powers are small. The boiling in the fluid in the bed promotes leveling and the angles of repose obtained are very small. For a specific power in water of 3.1 W/cm_3 a limiting angle of repose of less than 2 degrees is obtained after a time interval of between 1 and 3 hours. EDULCOREE-and ETABUL-research programs are carried out. (DG).

Energy Technology Data Exchange (ETDEWEB)

Following a postulated meltdown accident, the integrity of containment building structural material under attack by hot molten core debris and the safeguard of environment against radiological releases constitutes the final line of defense in PAHR safety assessment. Such assessment requires a good knowledge of UO/sub 2//interaction and penetration with different types of concrete. The present study focuses on the phenomena associated with core debris interaction/penetration with substrate basalt concrete.

International Nuclear Information System (INIS)

Objective: To develop a computerized method of internal dose estimation on radiation protection. Methods: Based on MIRD mathematic model of the organs and by means of the programming language of MS Visual Basic 6.0, a computer program of dose estimation in internal radiation was developed for radiation protection. Results: The computerized method of dose estimation for internal radiation was completed. Conclusions: This computerized method is very convenient for internal radiation dose estimation of several aspects. It can also be used in radiation accident. (authors)

International Nuclear Information System (INIS)

To estimate the success criteria of an operator's action time for a probabilistic safety/risk assessment (PSA/PRA) of a nuclear power plant, the information from a safety analysis report (SAR) and/or that by using a simplified simulation code such as the MAAP code has been used in a conventional PSA. However, the information from these is often too conservative to perform a realistic PSA for a risk-informed application. To reduce the undue conservatism, the use of a best-estimate thermal hydraulic code has become an essential issue in the latest PSA and it is now recognized as a suitable tool. In the same context, the 'ASME PRA standard' also recommends the use of a best-estimate code to improve the quality of a PSA. In Korea, a platform to use a best-estimate thermal hydraulic code called the MARS code has been developed for the PSA of the Korea standard nuclear power plant (KSNP). This study has proposed an estimation method for an operator's action time by using the MARS platform. ...

UK PubMed Central (United Kingdom)

OBJECTIVE: To use Medicaid claims data to construct patient origin-based market areas for dental services and compare constructed market areas with those based on the practice county. DATA SOURCES:...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy is conducting cleanup operations at the Weldon Spring site, St. Charles, Missouri, that will include development of a 77-ha (191-acre) soil borrow area. Eight wetlands, including riverine and palustrine emergent wetland types and totaling 0.9 ha (2.2 acres), will be eliminated during excavation of the borrow area. A 23-ha (57-acre) wetland/shorebird complex will be created at the Busch Conservation Area. The complex will include 2 ha (5 acres) of palustrine emergent wetland as mitigation for wetland losses in the borrow area.

Science.gov (United States)

... Air Station, Oahu, Kahuku Training Area ... K-Pier, Hawaii, Bradshaw Army Airfield, Hawaii (R&S ... impact area); Makua Military Reservation, Oahu (R&S ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Wastenet

market is addressed through a move to a recycling-led area-based franchise model. ...market is addressed through a move to a recycling-led area-based franchise model.

DEFF Research Database (Denmark)

Udgivelsesdato: May 2009

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The Cadomin area in Alberta contains two major coal mines and may be the site of Alberta's next new coal mine in the Coalspur Coalfield. No recent geological maps exist of the area. This paper details the methodology for mapping this heavily forested area. Coalbed methane potential is also discussed. 12 refs., 5 figs.

Wastenet

society organisations (more than 30) in reaching the most vulnerable groups and dealing with a subject area as sensitive

Energy Technology Data Exchange (ETDEWEB)

This Phase IV Remedial Design/Remedial Action Work Plan addresses the remediation of areas with the potential for UXO at the Idaho National Laboratory. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. Five areas within the Naval Proving Ground that are known to contain UXO include the Naval Ordnance Disposal Area, the Mass Detonation Area, the Experimental Field Station, The Rail Car Explosion Area, and the Land Mine Fuze Burn Area. The Phase IV remedial action will be concentrated in these five areas. For other areas, such as the Arco High-Altitude Bombing Range and the Twin Buttes Bombing Range, ordnance has largely consisted of sand-filled practice bombs that do not pose an explosion risk. Ordnance encountered in ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this paper is to perform an impact analysis of the Interim Storage Cask (ISC) of the Fast Flux Test Facility (FFTF) for a 4-ft end drop. The ISC is a concrete cask used to store spent nuclear fuels. The analysis is to justify the impact force calculated by General Atomics (General Atomics, 1994) using the ILMOD computer code. ILMOD determines the maximum force developed by the concrete crushing which occurs when the drop energy has been absorbed. The maximum force, multiplied by the dynamic load factor (DLF), was used to determine the maximum g-level on the cask during a 4-ft end drop accident onto the heavily reinforced FFTF Reactor Service Building`s concrete surface. For the analysis, this surface was assumed to be unyielding and the cask absorbed all the drop energy. This conservative assumption simplified the modeling used to qualify the cask`s structural integrity for this accident condition.

Energy Technology Data Exchange (ETDEWEB)

Condensing two-phase channel flow occurs in many industrial applications, including heating and refrigeration systems. It can also occur in certain nuclear reactor accidents. For example, during a small-break loss-of-coolant accident in a pressurized water reactor, following the partial depletion of the primary coolant, condensation of steam on the primary side of the steam generator tubes can provide a heat sink for disposal of the decay heat generated in the reactor core. Condensing two-phase flow can also play an important role in the operation of the passive emergency cooling system in the advanced simplified boiling water reactor. Here, steady-state condensation in the presence of a noncondensable in a concurrent two-phase channel flow is analyzed using a two-fluid model. The effect of noncondensables on the combined heat transfer at the liquid-gas mixture interphase is accounted for by using the stagnant film model, and closure relations ...

International Nuclear Information System (INIS)

The Belgian Tihange 2 nuclear power plant went into commercial operation in 1983 producing a thermal power of 2785 MW. Since the commissioning of the plant the steam generators U-tubes have been affected by primary stress corrosion cracking. In order to avoid further degradation of the performance and an increase in repair costs, Electrabel, the owner of the plant, decided in 1997 to replace the 3 steam generators. This decision was supported by the feasibility study performed by Tractebel Energy Engineering which demonstrated that an increase of 10% of the initial power together with a fuel cycle length of 18 months was achieved. Tractebel Energy Engineering was entrusted by Electrabel as the owner's engineer to manage the project. This paper presents the role of Tractebel Energy Engineering in this project and the safety analysis program necessary to justify the new operation point and the fuel cycle extension to 18 months re-analysis of FSAR chapter 15 accidents ...

Energy Technology Data Exchange (ETDEWEB)

The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE`s independent review and evaluation of the PFP FSAR and the basis for ...

International Nuclear Information System (INIS)

Tarapur Atomic Power Station 3 and 4 is a 540 MWe Pressurized Heavy Water Reactor. It uses 37 - element natural Uranium dioxide (UO_2) fuel pellets encapsulated inside the cylindrical sheath and are welded to the end plate at each end. During an postulated accident in which part of the fuel bundle are exposed to very high temperature (no means of heat removal) and other are at lower temperature (coolant temperature) possibility of failure of end plate weld due of thermal stresses developed by these relative temperature cannot be ruled out. In this report an attempt is made to study behaviour of fuel bundle under different temperature loading. Modelling of 37 element fuel bundle was done in ANSYS FEM. System was analysed for various sets of temperature loading. The system was analysed for plasticity and creep as material nonlinearity. The total strain, creep strain and stress increase as the temperature increases in upper portion of fuel bundle and decrease with ...

Energy Technology Data Exchange (ETDEWEB)

The efficacy of external flooding of a reactor vessel as a severe accident management strategy is assessed for an AP600-like reactor design. The overall approach is based on the Risk Oriented Accident Analysis Methodology (ROAAM), and the assessment includes consideration of bounding scenarios and sensitivity studies, as well as arbitrary parametric evaluations that allow the delineation of the failure boundaries. Quantification of the input parameters is carried out for an AP600-like design, and the results of the assessment demonstrate that lower head failure is physically unreasonable. Use of this conclusion for any specific application is subject to verifying the required reliability of the depressurization and cavity-flooding systems, and to showing the appropriateness (in relation to the database presented here, or by further testing as necessary) of the thermal insulation design and of the external surface properties of the lower head, ...

Energy Technology Data Exchange (ETDEWEB)

This report presents the thermal-hydraulic analysis of four Loss-of-Flow Accidents (LOFAs) in the first wall/blanket cooling system of the alternative SEAFP reactor design. The LOFAs considered result from a loss of electrical power for the recirculation pump in the primary cooling circuit. The analyses have been performed using the thermal-hydraulic system analysis code RELAP5/MOD3. In the analyses, special attention has been paid to the transient thermal-hydraulic behaviour of the cooling system and the temperature development in the first wall and blanket. For the LOFA without plasma shutdown, significant loss of heat removal due to dryout occurs at the midplane of the outboard first wall cooling pipes about 41 s after pump trip. For the three LOFA cases with emergency plasma shutdown that have been studied, the temperature increase in the Be-coating at the midplane of the outboard first wall is limited to about 30 K. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Presented in this paper is the transient analysis of a Group Distribution Header (GDH) following a guillotine break at the end of the header. The GDH is the most important component of reactor safety in case of accidents. Emergency Core Cooling System (ECCS) piping is connected to the GDH piping such that, during an accident, coolant passes from the GDH into the ECCS. The GDH that is propelled into motion after a guillotine break can impact neighboring GDH pipes or the nearest wall of the compartment. Therefore, two cases are investigated: GDH impact on an adjacent GDH and its attached piping; and GDH impact on an adjacent reinforced concrete wall. A whipping RBMK-1500 GDH along with neighboring concrete walls and pipelines is modeled using finite elements. The finite element code NEPTUNE used in this study enables a dynamic pipe whip structural analysis that accommodates large displacements and nonlinear material characteristics. The results ...

International Nuclear Information System (INIS)

The MACSTOR/KN-400 of Wolsung power plant in Korea is a dry interim storage facilities. There are 400 long slender cylinders in MACSTOR/KN-400. In one cylinder, ten baskets where Candu spent fuels are loaded are stacked and stored. For this MACSTOR/KN-400 facilities, analyses and tests for the hypothetical accident conditions that might happen during moving and storing baskets into a cylinder were performed. The hypothetical accident conditions to be considered are two cases. One is the case of basket dropping onto the bottom plate of a cylinder. The other is the case of basket dropping onto the other basket top plate stored in the cylinder. For the drop analyses, the case of hanging cylinder and the case of cylinder on the unyielding target surface were considered. Based on the dropping analysis, testing condition was determined as the latter case that is for the cylinder on the target surface. In a basket, 60 dummy fuel bundles are loaded ...

International Nuclear Information System (INIS)

A detailed outline of the application of the MELCOR and RELAP5/MOD3.1 codes to the analysis of the thermohydraulic response and determination of other parameters of the medium on the floor is given for several classes of secondary coolant circuit accidents along with the description of the related facilities. An overview is presented of the maximum values and time behavior of the thermohydraulic parameters, pressure, temperature, relative humidity, and water level on the floor. Transverse rupture of the steam generator, main steam header, or main feedwater header piping during normal operation is considered as the initiating event. Pressure is only 10% higher than the atmospheric pressure. Air temperature attains a value as high as 100 degC. Relative humidity is 100%, persisting as long as the steam source is available. The water level is typically about 8 cm and never exceeds 15 cm. (M.D.). 16 tabs., 37 figs., 32 refs.

International Nuclear Information System (INIS)

Debris coolability in the lower plenum of the reactor pressure vessel is an important factor for evaluation of debris in-vessel retention. The debris coolability analysis module is developed for the accurate prediction of the safety margin of the present reactor vessels in a severe accident. The module calculates debris spreading and cooling through melting and solidification in combination with a temperature distribution and failure evaluation of the vessel wall. Debris spreading is solved by the explicit method on a quasi-three-dimensional scheme and debris coolability is solved on the basis of natural convection analysis. The calculation for spreading is compared with a water spreading experiment on the floor and the calculation for coolability is compared with a n-octadecane melting experiment in a rectangular vessel. The comparisons show capabilities for predictions of spearhead transportation in the debris spreading process and of melting front transportation ...

Energy Technology Data Exchange (ETDEWEB)

Mitsubishi is now developing a new Pressurized water reactor (PWR), the Mitsubishi simplified PWR (MS-PWR), which has the innovative features of hybrid safety systems (an optimum combination of passive and active systems) and cooling by horizontal steam generators. In order to confirm the feasibility of the Mitsubishi hybrid safety system, various kinds of safety analyses are performed for loss-of-coolant accident events. In parallel to these safety analysis efforts, the following thermal-hydraulic tests are to be performed: (1) thermal-hydraulic test of a horizontal steam generator; (2) integrated thermal-hydraulic test using a simulation loop for the innovative MS-PWR (SLIM).

Energy Technology Data Exchange (ETDEWEB)

For light water reactors, loss of coolant is an important point in safety analysis, whereas for gas-cooled reactors the ingress of water into the core region is an incident of safety relevance. The applicability of the computer code system GAMTEREX to pebble beds of spherical high-temperature gas-cooled reactor fuel elements with simulated water ingress is verified by experiment. The measurements were performed at a Siemens-Argonaut reactor, using its ring core as a driver zone for a pebble-bed core in the center of the reactor.

International Nuclear Information System (INIS)

This paper presents a rationale for and a summary of tasks and missions to which mobile and stationary robots and other teleoperator-controlled devices could be assigned in response to the accidental release of radioactive and other hazardous/toxic materials to the environment. Many of these vehicles and devices currently support operation and maintenance of nuclear power plants and other nuclear industry facilities. This paper also discusses specific missions for these devices at the Three Mile Island and Chernobyl nuclear power plant sites at the time of the accidents. Also discussed is the status of devices under development for future applications, as well as research on robotics.

International Nuclear Information System (INIS)

After the reactor accident at Chernobyl on April 26, 1986 radioactive fallout was carried by air currents to most parts of Europe. The radioactive air currents reached Finland on April 27. Immediately after the arrival of such air in Finland, contamination of people by radioactive nuclides began via inhalation of this air. The ingestion route become important later, when radionuclides were transported via different foodchains to man. To determine the level of radionuclides in the body and to estimate the internal radiation doses caused by the Chernobyl accident, whole-body counting measurements were performed. The results of whole-body counting of six different groups of Finnish people measured during 1986 after the accident at Chernobyl are reported. Three were reference groups measured routinely once or twice annually, two groups were comprised of workers at nuclear power stations and one group consisted of 262 persons ...

International Nuclear Information System (INIS)

In this paper, probabilistic safety assessment (PSA) of the station blackout (SBO) and 5th emergency diesel in Daya Bay NPP has been carried out, the calculation method of non-recover factors of power supplies is given, and sensitivity analysis on the connection duration of 5th emergency diesel has been executed. It is concluded that the core damage frequency (CDF) induced by SBO is relatively large, the addition of 5th emergency diesel is very helpful for the CDF reduction, and the connection duration of this diesel has great effect on the CDF reduction

International Nuclear Information System (INIS)

In FY 1984 three specific tasks which are all related to not-well-understood two-phase phenomena of importance to LWR accidents have been identified under the program. These three tasks are: (1) inverted annular flow experiments and modeling; (2) hot leg U-bend two-phase flow simulation study; and (3) development and evaluation of two-phase flow scaling criteria. Some of the important results obtained under Tasks (1) and (2) are reported in this paper.

Energy Technology Data Exchange (ETDEWEB)

This paper presents a numerical simulation with the EUROPLEXUS fast dynamics software of a pipe whipping phenomenon occurring in the thermal hydraulic conditions of a loss of coolant accident in a PWR primary circuit. Different physical phenomena take place simultaneously during the rupture and the whipping of the pipe such as plasticity, contact, large displacements, two-phase flow regime and fluid structure interaction. Two kinds of numerical models - a simplified pipeline model and a mixed 1D/3D model - are considered and compared throughout modelling and computation. Numerical results are compared with experimental data belonging to the Aquitaine II test campaign.

Energy Technology Data Exchange (ETDEWEB)

Norwegian authorities regard with some disquiet the possibility of a criticality accident in a ship propulsion reactor core at the Kola coast. Along this coast, in land storages, floating storages and in submarines taken out of service, the total number of spent fuel reactor cores amount to two hundred. The total Cs-137 radioactivity in spent ship propulsion reactor fuel at the Kola peninsula can be assessed to 600,000 TBq. A worst case release may amount to more than 5,000 TBq Cs-137, a quantity which under unfavourable conditions might cause serious contamination locally and even across the border to Norway.

International Nuclear Information System (INIS)

In the analysis of the consequences of a hypothetical meltdown accident in an LMFBR, it is important to estimate the final location of the molten fuel pool in the concrete and ground underlying the reactor vessel. The GROWS program and the AYER program have been developed to calculate the final location of the molten fuel pool as the culmination of the transient analysis of this unusual Stefan problem but these programs require extensive computational resources. The solution is provided to the concrete and ground temperatures surrounding the stationary fuel pool and the related heat flux from the pool to the ground surface outside the containment building. This solution can be used to estimate the final location of the fuel pool and to check the end results of the sophisticated programs.

Energy Technology Data Exchange (ETDEWEB)

The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main topics presented in the fourth seminar were: thermal hydraulic experiments and analyses, primary collector integrity, feedwater distributor replacement, management of primary-to-secondary leakage accidents and new developments in the VVER safety technology. The number of participants, representing designers and manufacturers of the horizontal steam generators, plant operators, engineering companies, research organizations, universities and regulatory authorities, was 70 from 10 countries.

International Nuclear Information System (INIS)

During a hypothetical severe incident in a nuclear power plant with core meltdown a large part of radioactive material is present as aerosol particles in the reactor containment. In current severe accident containment codes the potential influences of hydrogen combustions on the behaviour of aerosols are not considered. Among other effects dry resuspension can increase the aerosol concentration in the atmosphere. Already deposited aerosol material can be re-released into the containment atmosphere by atmospheric currents induced by hydrogen deflagrations or by other phenomena like steam explosions. The objective is to assess the possible influence of this dry resuspension effect on the radioactive source term. (author)

Energy Technology Data Exchange (ETDEWEB)

The WWR-SM reactor at the Institute of Nuclear Physics of the Academy of Sciences (INP AS) in Uzbekistan was converted to 6-tube IRT-4M LEU (19.7%) fuel in 2009. Presently, INP intends to also use IRT-4M 8-tube FA, and a safety analysis for these 'mixed' (8-tube and 6-tube FA) cores is required by the regulatory authorities. This paper presents results of control rod ejection transient analysis for these mixed cores

Energy Technology Data Exchange (ETDEWEB)

The focus of the Chernobyl Studies Project has now turned to the issue of health effects from the Chernobyl accident. Currently, we are involved in and making progress on the case-control and co-hort studies of thyroid diseases among Belarussian children. Dosimetric aspects are a fundamental part of these studies. We are working to implement similar studies in Ukraine. A major part of the effort of these projects is supporting these studies, both by providing methods and applications of dose reconstruction and by providing support and equipment for the medical teams.

Energy Technology Data Exchange (ETDEWEB)

A novel device called the gas expansion model (GEM) is being developed at the Hanford Engineering Development Laboratory for testing in the 400-MW(th) fast flux test facility (FFTF) reactor. Incorporation of the GEM into liquid-metal reactor designs is intended to measurably contribute to the achievement of inherent safety, by allowing the reactor to passively shut down even in the extremely remote (hypothetical) event of an unprotected (no scram) loss-of-flow accident. The purpose of this paper is to describe the GEM and present predictive analyses of the effectiveness of the device during unprotected loss-of-flow experiments in the FFTF.

International Nuclear Information System (INIS)

When analyzing the loss-of-coolant accidents at VVER reactor NPP the problem of the effect of noncondensable gases on heat transfer in a horizontal steam generator (HSG) is gaining in importance. Based on the RELAP5/MOD3.2 computer code one analyzed the experiments to condense steam-and-gas mixture in a HSG. The calculations are shown to predict satisfactorily duration of steam generator poisoning from noncondensable gas

Energy Technology Data Exchange (ETDEWEB)

On July 18, 2001, a freight train carrying hazardous (non-nuclear) materials derailed and caught fire while passing through the Howard Street railroad tunnel in downtown Baltimore, Maryland. The United States Nuclear Regulatory Commission (USNRC), one of the agencies responsible for ensuring the safe transportation of radioactive materials in the United States, undertook an investigation of the train derailment and fire to determine the possible regulatory implications of this particular event for the transportation of spent nuclear fuel by railroad. Shortly after the accident occurred, the USNRC met with the National Transportation Safety Board (NTSB), the U.S. agency responsible for determining the cause of transportation accidents, to discuss the details of the accident and the ensuing fire. Following these discussions, the USNRC assembled a team of experts from the National Institute of Standards and Technology (NIST), ...

Energy Technology Data Exchange (ETDEWEB)

General-Purpose Heat Source radioisotope thermoelectric generators (GPHS-RTGs) will provide electrical power for the NASA Galileo and European Space Agency (ESA) Ulysses missions. Each GPHS-RTG comprises two major components: GPHS modules, which provide thermal energy, and a thermoelectric converter, which converts the thermal energy into electrical power. Each of the 18 GPHS modules in a GPHS-RTG contains four /sup 238/PuO/sub 2/-fueled capsules. LANL conducted a series of safety verification tests on the GPHS-RTG before the scheduled May 1986 launch of the Galileo spacecraft to assess the ability of the GPHS modules to contain plutonia in potential accident environments. As a result of the Challenger 51-L accident in January 1986, NASA postponed the launch of Galileo; the spacecraft launch vehicle was reconfigured and the spacecraft trajectory modified. These actions prompted NASA to reevaluate potential mission accidents ...

Energy Technology Data Exchange (ETDEWEB)

The understanding of fission product deposition in realistic steam generator conditions is needed for release estimates in PSA studies, and for the design of efficient accident management procedures. This is considered very important because primary-to-secondary leakages risk dominant sequences in many plants. Furthermore, the decay heat of the fission product deposits adds to the thermal load to the steam generator tubes also in other sequences, especially in case of cold leg leakages. This brings out the concern of induced steam generator tube ruptures in cases, where the steam generators are initially intact. The experimental data showed that the highest deposited fraction within the tubes were found in cases with lowest flow velocities. The minimum value of the deposited fraction was observed at intermediate flow velocities. With these relatively low Reynolds numbers, the results calculated with deposition models agree well with the experiments. At high ...

Energy Technology Data Exchange (ETDEWEB)

This decision document presents the selected remedial action for the Westerly Wetlands, Northerly Wetlands, and Tar Patch Area at the Burnt Fly Bog Superfund Site. It addresses contaminated soil present on the three remaining contaminated areas on the Site, including the Westerly Wetlands, Northerly Wetlands, and Tar Patch Area. The major components of the selected remedy include: Excavation and off-site disposal of contaminated soil from the Northerly Wetlands; Excavation and off-site disposal of contaminated soil from the Tar Patch Area; Backfilling the excavated area in the Northerly Wetland and reestablishing wetlands; Backfilling the excavated area in the Tar Patch Area and creating wetlands; Provision of additional security fencing around the Westerly Wetlands, and the recording of a Deed Notice for the Westerly Wetlands, Northerly ...

International Nuclear Information System (INIS)

This research centered on finding and perfecting methods of collection and disposal of refuse in Ibadan North Local Government Areas. The methodology used included questionnaire administration, personal interviews, field reconnaissance, and biochemical tests of water samples, all aimed at providing useful data for the design of effective methods of collecting and disposing refuse. The local government area was divided into three classes based on resident income: a high-income area (Bodija Avenue, etc.), a medium-income area (Sanngo, Oluyole, etc.), and a low-income area (Beere, Adeoyo, etc.). The research outcomes revealed that the waste generation rate for the local government ranged from 0.2 to 0.33 kg/cap/day and waste density ranged from 172.41 to 217.61 kg/m"3. Water analyses showed that the chloride, manganese, lead, and cadmium levels in water from low-income ...

British Library Electronic Table of Contents (United Kingdom)

Purpose - After almost 60 years of water supply development in Nigeria, it is unfortunate that as many as 43 per cent of the population still lack access to safe water. The situation is worse in the rural areas. There is, therefore, the need to better understand the constraints and challenges of water supply, especially in the rural areas of the country. With this regard this study seeks to assess the extent to which stakeholders are willing and able to adopt and implement sustainable, cost-effective and environmentally friendly management options for water resources in selected rural areas of Oyo State, Nigeria. Design/methodology/approach - The study areas include three rural/semi-urban Local Government Areas (LGAs) of Oyo state. The three LGAs are Ibarapa, Afijio, and Lagelu. The choice...

CERN Document Server

In the 21st century, Aerial and satellite images are information rich. They are also complex to analyze. For GIS systems, many features require fast and reliable extraction of open space area from high resolution satellite imagery. In this paper we will study efficient and reliable automatic extraction algorithm to find out the open space area from the high resolution urban satellite imagery. This automatic extraction algorithm uses some filters and segmentations and grouping is applying on satellite images. And the result images may use to calculate the total available open space area and the built up area. It may also use to compare the difference between present and past open space area using historical urban satellite images of that same projection

Science.gov (United States)

Environmental monitoring data were collected at and around the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site. These data are associated with radiation exposure, air, groundwater, meteorology, vadose zone, subsidence, and biota. This report summarizes the 2006 environmental data to provide an overall evaluation of RWMS performance and to support environmental compliance and performance assessment (PA) activities. Some of these data (e.g., radiation exposure, air, and groundwater) are presented in other reports (U.S. Department of Energy, 2006; Warren and Grossman, 2007; National Security Technologies, LLC, 2007). Direct radiation monitoring data indicate that exposure levels around the RWMSs are at or below background levels. Air monitoring data at the Area 3 and Area 5 RWMSs indicate that tritium concentrations are slightly above background levels. There is no ...

Science.gov (United States)

Este sistema de informacion provee al usuarion con un listado de areas protegidas argentinas ordenado por nombre, por provincia, ... ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the piezometer network is to establish baseline hydraulic head data for the water table aquifer at the F- and H-Area seeplines prior to startup of the groundwater extraction/injection remediation system.

Energy Technology Data Exchange (ETDEWEB)

Laboratory studies were performed to support field-testing of base injection into the F-Area Seepage Basins groundwater. The general purpose of these experiments is to provide information to guide the test of base injection and to identify potential adverse effects.

UK PubMed Central (United Kingdom)

A fundamental property of neuronal networks in Ammon’s horn is that each area is comprised of a single glutamatergic cell population and various types of GABAergic neurons. Here we describe...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThe objective of the study was to analyse the evolution of Bordetella pertussis population and the influence of herd immunity in different areas of the...Full Text Available

UK PubMed Central (United Kingdom)

The objectives of this study were to examine the association between dietary factors and underweight and overweight adult Vietnamese living in the rural areas of Vietnam. A cross-sectional study of...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundIn malarious areas of the world, a higher proportion of the population has blood group O than in non-malarious areas. This is probably due to a survival advantage conferred...Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... as time delay shifters for large-area phased arrays in military (MILSTAR) as well as commercial (Sky phone and other satellite communication) systems, ...

International Nuclear Information System (INIS)

... body body areas diagnostic techniques hazards health hazards mammals

Science.gov (United States)

This coverage describes forest practices and habitat conditions in the Hoh Usual and Accustomed Areas....

Science.gov (United States)

... in the Vicinity of Terminal Areas," Ph. ... WORDS Operations Research Stochastic processes Mathematical ... theory Aut',matic control Queueing theory ...

Science.gov (United States)

... AIR TRAFFIC, TERMINAL FLIGHT ... FLIGHT, RANDOM VARIABLES, STOCHASTIC PROCESSES ... COMPUTER PROGRAMS, QUEUEING THEORY. ...

Energy Technology Data Exchange (ETDEWEB)

A supplementary report to the plan for waste disposal in the Copenhagen area, Denmark. It presents a mapping of wastes and waste flow in invidual areas, a description of recycling methods and waste collection systems. In addition legislative demands and potentials are dealth with. (CLS).

Energy Technology Data Exchange (ETDEWEB)

Air Force Prototype Thermal Flash Protective Device (TFPD) Goggles were furnished to USAFSAM by the Life Support System Program Office, Aeronautical Systems Division, for determination and evaluation of their eye-type goggles caused stressed areas. The bonding used in the production model eliminated the stressed areas, resulting in increased closed-state optical density, particularly in the upper nasal area of the lens.

British Library Electronic Table of Contents (United Kingdom)

In order to provide pigs a comfortable sleeping area in hot weather, a floor cooling system was designed and applied to production buildings. Experiments were conducted to compare the floor temperatures and to observe the lying behaviour of pigs in the sleeping area of the buildings with and without floor cooling system. The results showed that, without the floor cooling system, the floor temperature was nearly the same as the air temperature in the open pig house. With the floor cooling system, the floor temperature of the sleeping area was controlled at 22-26degreeC, even though the air temperature was as high as 34degreeC, which improved the comfort of the pigs in the sleeping area. The pig lying behaviour was greatly affected by the floor temperature. More than 85% of the pigs were lyi...

British Library Electronic Table of Contents (United Kingdom)

The Sulige gas field and the Yulin gas field are located in the north of the Ordos Basin. Reservoir pressure in the Sulige area is subnormal, whereas reservoirs in the Yulin area have normal hydrostatic pressure. This paper provides an explanation of this difference. The characteristics of reservoir sediment and formation water chemistry in the gas reservoirs of these two areas were analyzed. The results showed that both reservoirs have good sealing ability. Data of numerical simulation showed that tectonic uplift resulted in a great reduction in formation pressure in the northern Ordos Basin during the late Cretaceous period, and the decrease was greater in the Yulin gas field than in the Sulige gas field. However, because the total hydrocarbon-generating intensity of the Sulige area (<24...