WorldWideScience

Sample records for acceptance tests

  1. L-286, Acceptance Test Record

    This document provides a detailed account of how the acceptance testing was conducted for Project L-286, ''200E Area Sanitary Water Plant Effluent Stream Reduction''. The testing of the L-286 instrumentation system was conducted under the direct supervision

  2. Nitrogen trailer acceptance test report

    This Acceptance Test Report documents compliance with the requirements of specification WHC-S-0249. The equipment was tested according to WHC-SD-WM-ATP-108 Rev.0. The equipment being tested is a portable contained nitrogen supply. The test was conducted at Norco's facility

  3. Nitrogen trailer acceptance test report

    Kostelnik, A.J.

    1996-02-12

    This Acceptance Test Report documents compliance with the requirements of specification WHC-S-0249. The equipment was tested according to WHC-SD-WM-ATP-108 Rev.0. The equipment being tested is a portable contained nitrogen supply. The test was conducted at Norco`s facility.

  4. Acceptance tests and commissioning measurements

    Following the installation of a therapy machine, be it an orthovoltage X ray unit, cobalt unit, linac or brachytherapy machine, in a radiotherapy clinic, the medical physicist must perform a series of measurements and tasks prior to placing the unit into clinical operation. These duties include acceptance testing and commissioning. Various dosimetric and radiation measuring instruments and techniques are discussed

  5. Acceptance test of LANTIS system

    Acceptance tests of radiotherapy equipment are very important. It is essential for the quality control of the equipment. Quality assurance checks for LANTIS was done during the installation and also periodically. QA involves checks for individual workstations, as well as for overall system. In modern radiotherapy centers, transferring data from one workstation to another via networking improves the quality of the treatment, reduces the errors and reduces the overall treatment time. In this hospital, Local Area Network Therapy Information system (LANTIS) from Siemens, is available for patient data transfer. Here, some of the acceptance checks carried out are presented

  6. Mini-DACS acceptance test report

    The attached document is the acceptance test summary report, of the mini-DACS, that was used to test the spare mixer pump for tank 241-SY-101, at the maintenance and storage facility (MASF). It includes a copy of the acceptance test procedure (ATP) and all pertaining ECNS

  7. Acceptance testing of photographic film dosemeters

    The reports describes a system for acceptance testing of photographic film dosemeters in customary use in personal dosimetry. The system comprises a test of some of the fundamental dosimetric properties of the film. The acceptance test will be performed in connection with the semi-annual purchases of dosemeter film to the National Institute of Radiation Hygiene. The test program comprises both constancy tests and absolute requirements. The latter refer mainly to ISO 1757 - Personal photographic dosemeters. 2 refs

  8. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal

  9. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    NNSA/NSO Waste Management Project

    2008-06-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal.

  10. Acceptance Test Plan for ANSYS Software

    This plan governs the acceptance testing of the ANSYS software (Full Mechanical Release 5.5) for use on Project Word Management Contract (PHMC) computer systems (either UNIX or Microsoft Windows/NT). There are two phases to the acceptance testing covered by this test plan: program execution in accordance with the guidance provided in installation manuals; and ensuring results of the execution are consistent with the expected physical behavior of the system being modeled

  11. Cone penetrometer moisture probe acceptance test report

    This Acceptance Test Report (ATR) documents the results of WHC-SD-WM-ATP-146 (Prototype Cone Penetrometer Moisture Probe Acceptance Test Procedure) and WHC-SD-WM-ATP-145 (Cone Penetrometer Moisture Probe Acceptance Test Procedure). The master copy of WHC-SD-WM-ATP-145 can be found in Appendix A and the master copy of WHC-SD-WM-ATP-146 can be found in Appendix B. Also included with this report is a matrix showing design criteria of the cone penetrometer moisture probe and the verification method used (Appendix C)

  12. Generator acceptance test and inspection report

    This Acceptance Test Report(ATR) is the completed testing and inspection of the new portable generator. The testing and inspection is to verify that the generator provided by the vendor meets the requirements of specification WHC-S-0252, Revision 2. Attached is various other documentation to support the inspection and testing

  13. DACS upgrade acceptance test report

    The DACS, which is housed in a trailer located just outside of the north fence at the SY tank farm, receives input signals from a variety of sensors located in and around the SY-101 tank. These sensors provide information such as: (1) tank vapor space and ventilation system H2 concentration; (2) tank waste temperature; (3) tank pressure; (4) waste density; (5) operating pump parameters such as speed, flow, rotational position, discharge pressure, and internal temperature; (6) strain (for major equipment); and (7) waste level. The output of these sensors is conditioned and transmitted to the DACS computers where these signals are displayed, recorded, and monitored for out-of-specification conditions. If abnormal conditions are detected, then, in certain situations, the DACS automatically generates alarms and causes the system to abort pump operations. The report documents testing performed per WHC-SD-WM-ATP-082. Rev. 0-13

  14. Gas characterization system software acceptance test report

    This document details the results of software acceptance testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

  15. Gas characterization system software acceptance test procedure

    This document details the Software Acceptance Testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

  16. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    This document establishes the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal. Mixed waste generated within the State of Nevada by NNSA/NSO activities is accepted for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Site for storage or disposal

  17. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION, NEVADA SITE OFFICE

    2005-07-01

    This document establishes the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal. Mixed waste generated within the State of Nevada by NNSA/NSO activities is accepted for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Site for storage or disposal.

  18. Breathing air trailer acceptance test report

    This Acceptance Test Report documents compliance with the requirements of specification WHC-S-0251, Rev.0 and ECNs 613530 and 606113. The equipment was tested according to WHC-SD-WM-ATP-104. The equipment tested is a Breathing Air Supply Trailer purchased as a design and fabrication procurement activity. The ATP was written by the Seller and was performed by the Seller with representatives of the Westinghouse Hanford Company witnessing portions of the test at the Seller's location

  19. Acceptance test report: Backup power system

    Acceptance Test Report for construction functional testing of Project W-030 Backup Power System. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. Backup power includes a single 125 KW diesel generator, three 10-kva uninterruptible power supply units, and all necessary control

  20. Void fraction instrument acceptance test procedure

    This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating as designed

  1. W-087 Acceptance test procedure. Revision 1

    Joshi, A.W.

    1997-06-10

    This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks.

  2. Diesel generator trailer acceptance test procedure

    This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0252 Rev. 1 and ECNs 609271, and 609272. The equipment being tested is a 150KW Diesel Generator mounted on a trailer with switchgear. The unit was purchased as a Design and Fabrication procurement activity. The ATP was written by the Seller and will be performed by the Seller with representatives of the Westinghouse Hanford Company witnessing the test at the Seller's location

  3. GERDA phase II detectors and acceptance tests

    The GERDA collaboration aims at searching for the neutrinoless double beta decay of 76Ge into 76Se. It uses enriched Ge detectors that are operated in liquid argon. Phase I of the experiment started with a target mass of approximately 20 kg on November 1, 2011, and it will last for 1 year. Phase II is in preparation and envisions the installation of at least 25 new Broad Energy Ge detectors (BEGe) that will increase the target mass by nearly 20 kg. These detectors, however, have to be extensively tested prior to their usage. The talk briefly reviews the preparation of the detector screening campaign and focuses on the corresponding acceptance test strategy. The tests include energy resolution and leakage current measurements, dead layer and active volume determination, as well as the pulse shape discrimination efficiencies of the detectors. Finally we present results obtained with depleted BEGe detectors that are used for the optimization of the enriched ones during the acceptance tests.

  4. Void fraction instrument acceptance test procedure

    This document presents the results of the acceptance test for the mechanical and electrical features (not specifically addressed by the software ATP) of the void fraction instrument (VFI). Acceptance testing of the VFI, control console, and decontamination spray assembly was conducted in the 306E building high bay and area adjacent to the facility. The VFI was tested in the horizontal position supported in multiple locations on rolling tables. The control console was located next to the VFI pneumatic control assembly. The VFI system was operated exactly as is expected in the tank farm, with the following exceptions: power was provided from a building outlet and the VFI was horizontal. The testing described in this document verifies that the mechanical and electrical features are operating as designed and that the unit is ready for field service

  5. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal

  6. Nevada Test Site Waste Acceptance Criteria

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal

  7. Nevada Test Site Waste Acceptance Criteria

    U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2005-10-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal.

  8. Acceptance Testing Of Web Applications With Test Description Language

    Łukasz Olek; Bartosz Alchimowicz; Jerzy Nawrocki

    2014-01-01

    Acceptance tests are usually created by a client after a part of a system is implemented. However, some methodologies propose the elaboration of test cases before implementing a system. This approach increases the probability of system implementation that fulfills requirements, but may be problematic for customers and testers. To allow acceptance testing in such conditions, we propose to define test cases by recording them on an interactive mockup (a low detailed user-interface prototype). Th...

  9. W-026, acceptance test report manipulator system

    Watson, T.L.

    1997-04-15

    The purpose of the WRAP Manipulator System Acceptance Test Plan (ATP) is to verify that the 4 glovebox sets of WRAP manipulator components, including rail/carriage, slave arm, master controller and auxiliary equipment, meets the requirements of the functional segments of 14590 specification. The demonstration of performance elements of the ATP are performed as a part of the Assembly specifications. Manipulator integration is integrated in the performance testing of the gloveboxes. Each requirement of the Assembly specification will be carried out in conjunction with glovebox performance tests.

  10. Acceptance Testing Of Web Applications With Test Description Language

    Łukasz Olek

    2014-01-01

    Full Text Available Acceptance tests are usually created by a client after a part of a system is implemented. However, some methodologies propose the elaboration of test cases before implementing a system. This approach increases the probability of system implementation that fulfills requirements, but may be problematic for customers and testers. To allow acceptance testing in such conditions, we propose to define test cases by recording them on an interactive mockup (a low detailed user-interface prototype. The paper focuses on Test Description Language, a notation used to store test cases.

  11. Nevada test site waste acceptance criteria

    This document provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  12. Payload test philosophy. [JPL views on qualification/acceptance testing

    Gindorf, T.

    1979-01-01

    The general philosophy of how JPL views payload qualification/acceptance testing for programs that are done either in-house or by contractors is described. Particular attention is given to mission risk classifications, preliminary critical design reviews, environmental design requirements, the thermal and dynamics development tests, and the flight spacecraft system test.

  13. SPECT: How much acceptance testing is reasonable?

    Full text: Whereas in radiology national standards for acceptance testing of medical instrumentation are available, in nuclear medicine this is not the case. This resulted in some kind of uncertainty, so that the Austrian Societies for Nuclear Medicine and for Medical Physics decided to establish a task group for developing guidelines for acceptance testing. One important item that has to be kept in mind is the fact that acceptance testing of radiological equipment has to assure the observation of prescribed limits of radiation. Otherwise there would arise the risk of increased radiation exposure of the patient. On the other hand, the aim of acceptance testing of gamma cameras is only to assure that the specifications are observed. There are no prescribed limits and there is no risk for the patient. There are two standards for defining specifications of gamma cameras: the NEMA standards and the IEC standards. Most of the manufacturers determine the specifications of their gamma cameras according to the NEMA standards, so if we want to check the specifications in the field, we have to use the same methods as the manufacturer, that is the NEMA standards. The questions are: Should we check all parameters defined in the NEMA standards? That would not be possible in the field. Which parameters should we select? In which extent and how precisely should we check? In any case, there must be a reasonable balance between time and financial effort and technical information obtained. Facing these problems our task group decided to propose the following procedure: First, we apply all tests which are called 'primary tests' in the NEMA standards: 1. Intrinsic spatial resolution 2. Intrinsic energy resolution 3. Intrinsic flood field uniformity 4. System spatial resolution without scatter 5. System alignment 6. SPECT reconstructed spatial resolution without scatter 7. Whole body system spatial resolution without scatter. All these tests are basically performed according to the

  14. Acceptance testing and QA in interventional cardiology

    Interventional radiology has seen rapid growth in the field of cardiology over the past decade. This growth has been facilitated by advances in imaging technology and the development of increasingly sophisticated dedicated radiological equipment. Interventional cardiology (IC) procedures are complex and may involve prolonged irradiations, which may subject patients and operators to higher levels of risk than those, which normally prevail. Currently interventional cardiology contributes over 10% to annual collective dose in the UK in spite of contributing to a total annual frequency of 0.68%. The EU Medical Exposures Directive, 97/43/Euratom, identifies interventional radiology as an area of special concern. Acceptance testing and routine quality assurance (QA) programmes are particularly important in the field of interventional cardiology given the above. The requirements for acceptance testing and QA are underpinned in the EU Medical Exposures Directive and consequent national legislation. A QA survey of 16 interventional cardiology systems in Ireland was carried out by the Department of Medical Physics and Bioengineering, St. James's Hospital, Dublin. This is the continuation of a recently published survey and represents over half of the interventional cardiology systems in Ireland including new technology digital flat panel systems and dedicated mobile equipment in trailors. Acceptance testing and QA protocols were developed and reviewed in accordance with current international and national guidelines, standards and literature. Testing included assessing the performance of the X ray tube and generator, the automatic exposure control (AEC) device in fluoroscopy and digital acquisition modes and a subjective assessment of image quality using the Leeds test objects. Radiation shielding calculations and measurements were performed to determine the structural shielding required by new installations and electrical, mechanical and general radiation safety was also

  15. Acceptance Test Report for 241-U compressed air system

    This Acceptance Test Report (ATR) documents the results of acceptance testing of a newly upgraded compressed air system at 241-U Farm. The system was installed and the test successfully performed under work package 2W-92-01027

  16. Acceptance tests of a new gamma camera

    For best patient service, a QA programme is needed to produce quantitative/qualitative data and keep records of the results and equipment faults. Gamma cameras must be checked against the manufacturer's specifications.The service manual is usually useful to achieve this goal. Acceptance tests are very important not only to accept a new gamma camera system for routine clinical use but also to have a role in a reference for future measurements. In this study, acceptance tests were performed for a new gamma camera in our department. It is a General Electric MG system with two detectors, two collimators. They are low energy general purpose (LEGP) and medium energy general purpose (MEGP). All intrinsic calibrations and corrections were done by the service engineer at installation (PM tune, dynamic correction, energy calibration, geometric calibration, energy correction, linearity correction and second order corrections).After installation, calibrations and corrections, a close physical inspection of the mechanical and electrical safety aspects of the cameras were done by the responsible physicist of the department. The planar system is based on measurement of system uniformity, resolution/linearity and multiple window spatial registration. All test procedures were performed according to NEMA procedures developed by the manufacturer. Intrinsic uniformity: NEMA uniformity was done first by using service manual and then other isotope uniformities were acquired with 99mTc, 131I, 201Tl and 67Ga. They were evaluated qualitatively and quantitatively, but non-uniformities were observed, especially for detector II, The service engineers repeated all tests and made necessary corrections. We repeated all the intrinsic uniformity tests. 99mTc intrinsic images were also performed at 'no correction', 'no energy correction', 'no linearity correction', 'all correction' and '±10% off peak', and compared. Extrinsic uniformity: At the beginning, collimators were checked for defects

  17. Acceptance-test specifications for Test Number Four: process sensor and display test

    This document provides the general instructions for performing acceptance Test Number Four as indicated in the Acceptance Test Index (TI-022-130-003). Also indicated are the plant conditions and special equipment required to conduct the test. The acceptance criteria for each portion of the test are specified

  18. Acceptance testing and QA in dental radiology

    The HPA (UK) reported in 2002 that although the effective dose from dental examinations is low, dental imaging is the most frequent type of X ray examination undertaken (approx. 30%); a similar situation is likely to exist in Ireland. It is most likely that this will increase further in the future as the dental X ray technology moves from film to digital equipment. Dental X rays are taken more frequently with digital equipment than film based technology. The Department of Medical Physics and Bioengineering, St. James's Hospital, Dublin is particularly interested in the area of dental quality assurance (QA) as a result of a significant medical radiation safety incident in Ireland occurring with a faulty dental X ray installation. The implementation of a QA programme in Ireland has been enforced not only by the publication of the Dental Code of Practice by the Irish Regulatory Authority in the 1990s but also by the publication of the European Medical Exposures Directive. The current QA programme, which includes site visits in order to perform acceptance testing and routine QA checks on dental X ray equipment has been implemented in approximately 250 dental health centres to which the Department has provided radiation protection advisory services for approximately twenty years. In addition to the technical evaluation of the equipment, an assessment of the adequacy of the shielding in the X ray room and of the radiation protection facilities is performed. This paper identifies the findings from the dental radiology QA assessments. QA test protocols were developed in accordance with current national and internationally accepted guidelines. The tests include exposure time and kVp accuracy, radiation output consistency, filtration, irradiated field size, mechanical and electrical safety checks and measurement of tube output for specific X ray examinations to aid in the establishment of a national diagnostic reference levels, a requirement of the Medical Exposures

  19. On acceptance criteria for Mochovce startup physical tests

    Paper is focused on new acceptance criteria for physical startup tests of Mochovce Units 1, 2. The acceptance criteria are discussed at the stage of their development. The acceptance criteria determination is based on statistical processing of differences between the experimental and theoretical values of neutron-physical characteristics. The experimental values were taken from physical startup tests of Bohunice Unit 1, 2 and 4 and Dukovany Unit 1 - 4. The theoretical values were calculated by code BIPR-7. The acceptance criteria were established for critical boron concentration, core loading symmetry measurement, boric acid worth, temperature reactivity coefficient, 'ejected' control rod worth, pressure reactivity coefficient and power reactivity coefficient. The new acceptance criteria were applied to evaluate results of physical startup tests of Mochovce Unit 1 in June 1998. The acceptance criteria showed to be adequate. The summary results of statistical processing and the comparison of earlier, new and US acceptance criteria for physical startup tests are presented.(Authors)

  20. User acceptance testing a step-by-step guide

    Hambling, Brian

    2013-01-01

    Every information system brought into service in every type of organisation requires user acceptance testing. This book is a hands-on manual for non-testing specialists to plan and carry out an effective acceptance test of an information system. It also identifies ways of making the process as simple and cost-effective as possible.

  1. On acceptance criteria for Mochovce startup physical tests

    New acceptance criteria are discussed for physical startup tests of Mochovce Units 1, 2, at the stage of their development. The acceptance criteria determination is based on statistical processing of differences between the experimental and theoretical values of neutron-physical characteristics. The experimental values were taken from physical startup tests of Bohunice Unit 1, 2 and 4 and Dukovany Unit 1 - 4. The theoretical values were calculated by code BIPR-7. The acceptance criteria were established for critical boron concentration, core loading symmetry measurement, boric acid worth, temperature reactivity coefficient, 'ejected' control rod worth, pressure reactivity coefficient and power reactivity coefficient. The new acceptance criteria were applied to evaluate results of physical startup tests of Mochove Unit 1 in June 1998. The acceptance criteria showed to be adequate. The summary results of statistical processing and the comparison of earlier, new and US acceptance criteria for physical startup tests are presented. (author)

  2. 105-KE Isolation Barrier Leak Rate Acceptance Test Report

    McCracken, K.J.

    1995-06-14

    This Acceptance Test Report (ATR) contains the completed and signed Acceptance Procedure (ATP) for the 105-KE Isolations Barrier Leak Rate Test. The Test Engineer`s log, the completed sections of the ATP in the Appendix for Repeat Testing (Appendix K), the approved WHC J-7s (Appendix H), the data logger files (Appendices T and U), and the post test calibration checks (Appendix V) are included.

  3. 105-KE Isolation Barrier Leak Rate Acceptance Test Report

    This Acceptance Test Report (ATR) contains the completed and signed Acceptance Procedure (ATP) for the 105-KE Isolations Barrier Leak Rate Test. The Test Engineer's log, the completed sections of the ATP in the Appendix for Repeat Testing (Appendix K), the approved WHC J-7s (Appendix H), the data logger files (Appendices T and U), and the post test calibration checks (Appendix V) are included

  4. Nevada Test Site Waste Acceptance Criteria, December 2000

    NONE

    2000-12-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal.

  5. Nevada Test Site Waste Acceptance Criteria, December 2000

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal

  6. Acceptance test procedure for High Pressure Water Jet System

    The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet

  7. Enraf Series 854 advanced technology gauge (ATG) acceptance test procedure

    This Acceptance Test Procedure was written to test the Enraf Series 854 Advanced Technology Gauge (ATG) prior to installation in the Tank Farms. The procedure sets various parameters and verifies that the gauge is functional

  8. Acceptance test report for core sample trucks 3 and 4

    The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ''Engineering Practice Guidelines,'' Appendix M, ''Acceptance Test Procedures and Reports.'' Rotary mode core sample trucks 3 and 4 were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Successful completion of acceptance testing on June 30, 1995 verified that all design requirements were met. This report is divided into four sections, beginning with general information. Acceptance testing was performed on trucks 3 and 4 during the months of March through June, 1995. All testing was performed at the ''Rock Slinger'' test site in the 200 West area. The sequence of testing was determined by equipment availability, and the initial revision of the Acceptance Test Procedure (ATP) was used for both trucks. Testing was directed by ICF-KH, with the support of WHC Characterization Equipment Engineering and Characterization Project Operations. Testing was completed per the ATP without discrepancies or deviations, except as noted

  9. Operator coil monitoring Acceptance Test Procedure

    The readiness of the Data Acquisition and Control System (DACS) to provide monitoring and control of the Programmable Logic Controller (PLC) abort coils from the Master and RSS stations will be systematically tested during performance of this procedure. It should be noted that these are not physical abort coils but software coils controlled by the software's ladder logic. The readiness of the DACS to properly interface with the ENRAF wire level gauge installed in the SY-101 storage tank will also be tested. During this test, a verification of all abort coil indications will be conducted at the DACS Development Facility in the 306E Building by injecting an input signal for each DACS sensor that has an associated abort coil until the abort coil actuates, and then ensuring that the status of the abort coil indicated at the Master and RSS stations is correct. Each abort coil will also be tested to ensure that the ''ENABLE'' and ''DISABLE'' controls from the Master and RSS stations function correctly, and only with the use of proper passwords

  10. First experiences with acceptance testing of multiple head SPECT cameras

    User acceptance testing of newly installed gamma cameras is mandatory in order to verify manufacturers' specifications and to ensure optimal image quality. Acceptance test procedures are widely standardized today and are carried out following commonly accepted test protocols. Two new triple head gamma cameras have been installed during the last year at the Department of Nuclear Medicine of the Vienna University Hospital. For acceptance testing of these cameras a modified and expanded version of the commonly used test protocol for single head SPECT systems has been employed. Details of the tests that have been carried out and a comparison of the results obtained for both cameras are presented. Furthermore, some specific problems that are encountered during acceptance testing of multiple head systems are discussed. In particular it has been noted that some important tests of intrinsic camera parameters cannot be carried out, which makes a complete verification of vendors' specifications impossible. In spite of these problems the acceptance test system for multiple head cameras presented in this work was sufficient for establishing proper working conditions for clinical use. (authors)

  11. Acceptance test report for the Westinghouse 100 ton hydraulic trailer

    The SY-101 Equipment Removal System 100 Ton Hydraulic Trailer was designed and built by KAMP Systems, Inc. Performance of the Acceptance Test Procedure at KAMP's facility in Ontario, California (termed Phase 1 in this report) was interrupted by discrepancies noted with the main hydraulic cylinder. The main cylinder was removed and sent to REMCO for repair while the trailer was sent to Lampson's facility in Pasco, Washington. The Acceptance Test Procedure was modified and performance resumed at Lampson (termed Phase 2 in this report) after receipt of the repaired cylinder. At the successful conclusion of Phase 2 testing the trailer was accepted as meeting all the performance criteria specified

  12. Factory Acceptance Test Procedure Westinghouse 100 ton Hydraulic Trailer

    This Factory Acceptance Test Procedure (FAT) is for the Westinghouse 100 Ton Hydraulic Trailer. The trailer will be used for the removal of the 101-SY pump. This procedure includes: safety check and safety procedures; pre-operation check out; startup; leveling trailer; functional/proofload test; proofload testing; and rolling load test

  13. The Murmansk Initiative - RF: Acceptance Testing

    Czajkowski, C.; Wester, D. W.; Dyer, R. S.; Soerlie, A. A.; Moller, B.; Barnes, E.

    2002-02-26

    The Murmansk Initiative-RF (MI) was conceived to provide the Russian Federation (RF) with the capacity to manage low-level liquid radioactive waste (LLRW) and comply with the requirements of the London Convention that prohibit ocean dumping. The trilateral project among Norway, the RF, and the United States of America (U.S.) began in 1994 and was the first to utilize exclusively Russian subcontractors to upgrade and expand an existing LLRW treatment plant on the premises of RTP Atomflot in Murmansk, Russia. The project moved quickly through the design phase. Progress during the construction phase was somewhat slower because of difficulties with acquisition of hardware, inexperience with automated instrumentation and control equipment, and unexpected design changes in the cementation unit. The project advanced into the test-operation phase, which is currently underway, in June 2001. Initial runs with liquid waste have revealed that procedures for unloading spent ion-exchange sorbents could be improved and that sludges formed during removal of alkaline-earth metals should be compacted in order for the facility to operate at its full potential. Resolution of these issues is expected within the next few months.

  14. Acceptance test procedure MICON software exhaust fan control modifications

    This acceptance test verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, and the alarms for the new emergency fan damper backup air compressor

  15. Product acceptance environmental and destructive testing for reliability.

    Dvorack, Michael A.; Kerschen, Thomas J.; Collins, Elmer W.

    2007-08-01

    To determine whether a component is meeting its reliability requirement during production, acceptance sampling is employed in which selected units coming off the production line are subjected to additional environmental and/or destructive tests that are within the normal environment space to which the component is expected to be exposed throughout its life in the Stockpile. This report describes what these tests are and how they are scored for reliability purposes. The roles of screens, Engineering Use Only tests, and next assembly product acceptance testing are also discussed, along with both the advantages and disadvantages of environmental and destructive testing.

  16. Acceptance testing protocol for magnetic resonance imaging systems

    Objective: to develop an acceptance testing protocol for magnetic resonance imaging systems and to show which and how phantoms could be used to collect data. Materials and methods: the definition, procedure, analysis and the acceptation criteria were created for each of 15 selected tests. Results: These tests allow the evaluation of technical specifications stated on the manufacturer's sales proposal and to establish reference values to be used in subsequent constancy tests. Conclusion: future quality assurance programs in magnetic resonance imaging should consider employing tests similar or equal to the ones described in this paper. (author)

  17. Acceptance test report for the AY-102 ENRAF densitometer

    On February 11, 1998, the AY-1 02, Riser 15E ENRAF Densitometer was acceptance tested per HNF-SD-WM-ATP-077. The test was performed at the Department of Energy's Hanford Site, 200 East Area, building MO-407. The test validated the functionality of the Densitometer for use by project W-320, C-1 06 Retrieval. The purpose of the test procedure was to verify the functionality of the ENRAF Series 854 ATG densitometer. Typically, all ENRAF Series 854 ATGs are acceptance tested before transport to the field. The ATP, as performed for level gauges, sets default program values within the gauge and verifies the gauge's force transducer calibration

  18. W-026, acceptance test report LLW supercompactor (submittal number 567)

    The purpose of this acceptance test report was to verify the assembly is correct and complete and meets all the specification and performance requirements. On May 15--16, 1996, the LLW Supercompactor functional demonstrations and performance tests were carried out. These tests were carried out in accordance with the Acceptance Test Procedure, submittal 565, dated 5/3/96. The tests were performed by Herman Miller and Gene Rice of INET Corporation and Richard Lawrence and other PCL personnel. The VIHC representative on May 15, 1996 was Doug Dunlap and on May 16, 1996 the representative was Ken Leist

  19. W-026, transuranic waste (TRU) glovebox acceptance test report

    Leist, K.J.

    1998-03-11

    On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, sorting table, lidder/delidder device and the TRU empty drum compactor were also conducted. As of February 25, 1998, 10 of the 102 test exceptions that affect the TRU glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test exceptions are provided as appendices to this report.

  20. WRAP low level waste (LLW) glovebox acceptance test report

    Leist, K.J.

    1998-02-17

    In June 28, 1997, the Low Level Waste (LLW) glovebox was tested using glovebox acceptance test procedure 13031A-85. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, lidder/delidder device and the supercompactor were also conducted. As of November 24, 1997, 2 of the 131 test exceptions that affect the LLW glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test Exceptions are provided as appendices to this report.

  1. W-026, transuranic waste (TRU) glovebox acceptance test report

    On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, sorting table, lidder/delidder device and the TRU empty drum compactor were also conducted. As of February 25, 1998, 10 of the 102 test exceptions that affect the TRU glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test exceptions are provided as appendices to this report

  2. WRAP low level waste (LLW) glovebox acceptance test report

    In June 28, 1997, the Low Level Waste (LLW) glovebox was tested using glovebox acceptance test procedure 13031A-85. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, lidder/delidder device and the supercompactor were also conducted. As of November 24, 1997, 2 of the 131 test exceptions that affect the LLW glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test Exceptions are provided as appendices to this report

  3. PUREX SAMCONS uninterruptible power supply (UPS) acceptance test report

    This Acceptance Test Report for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) Acceptance Test Procedure validates the operation of the UPS, all alarming and display functions and the ability of the UPS to supply power to the SAMCONS as designed. The proper installation of the PUREX SAMCONS Trailer UPS components and wiring will be systematically evaluated by performance of this procedure. Proper operation of the SAMCONS computer UPS will be verified by performance of a timed functional load test, and verification of associated alarms and trouble indications. This test procedure will be performed in the SAMCONS Trailer and will include verification of receipt of alarms at the SAMCONS computer stations. This test may be performed at any time after the completion of HNF-SD-CP-ATP-083, PUREX Surveillance and Monitoring and Control System (SAMCONS) Acceptance Test Procedure, when computer display and alarm functions have been proven to operate correctly

  4. Two Types of Test Assembly Checked and Accepted for CEFR

    2002-01-01

    The detail design of two types of test assembly used in the simulating transportation, and themounting and hydraulic test were completed in 2002. This two types of test assembly are manufactured inshanghai No.1 machine tool works, and checked and accepted in March 2003. The former is used in the

  5. Surface moisture measurement system hardware acceptance test procedure

    The purpose of this acceptance test procedure is to verify that the mechanical and electrical features of the Surface Moisture Measurement System are operating as designed and that the unit is ready for field service. This procedure will be used in conjunction with a software acceptance test procedure, which addresses testing of software and electrical features not addressed in this document. Hardware testing will be performed at the 306E Facility in the 300 Area and the Fuels and Materials Examination Facility in the 400 Area. These systems were developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks

  6. Research on control rod drive mechanism seismic test acceptance criteria

    Background: There is no clear requirement on the rod drop performance of Control Rod Drive Mechanism (CRDM) in seismic condition. Purpose: Acceptance criteria of AP1OOO CRDM seismic test need to be determined. Methods: Related regulations and the safety function of AP1000 CRDM are investigated, as well as the conclusions drawn from the CRDM seismic tests worldwide. Results: Acceptance criteria of this test should be in accordance with the limit is in AP1OOO Nuclear Plant Safety Analysis Report. Conclusions: Drop time of control rods in AP1000 CRDM seismic test at the room temperature without flow is 2.7 s before and after Safe Shutdown Earthquake (SSE). (authors)

  7. Neutron absorber qualification and acceptance testing from the designer's perspective

    Starting in the mid 1990's, the USNRC began to require less than 100% credit for the 10B present in fixed neutron absorbers spent fuel transport packages. The current practice in the US is to use only 75% of the specified 10B in criticality safety calculations unless extensive acceptance testing demonstrates both the presence of the 10B and uniformity of its distribution. In practice, the NRC has accepted no more than 90% credit for 10B in recent years, while other national competent authorities continue to accept 100%. More recently, with the introduction of new neutron absorber materials, particularly aluminum / boron carbide metal matrix composites, the NRC has also expressed expectations for qualification testing, based in large part on Transnuclear's successful application to use a new composite material in the TN-68 storage / transport cask. The difficulty is that adding more boron than is really necessary to a metal has some negative effects on the material, reducing the ductility and the thermal conductivity, and increasing the cost. Excessive testing requirements can have the undesired effect of keeping superior materials out of spent fuel package designs, without a corresponding justification based on public safety. In European countries and especially in France, 100% credit has been accepted up to now with materials controls specified in the Safety Analysis Report (SAR): Manufacturing process approved by qualification testing Materials manufacturing controlled under a Quality Assurance system. During fabrication, acceptance testing directly on products or on representative samples. Acceptance criteria taking into account a statistical uncertainty corresponding to 3σ. The original and current bases for the reduced 10B credit, the design requirements for neutron absorber materials, and the experience of Transnuclear and Cogema Logistics with neutron absorber testing are examined. Guidelines for qualification and acceptance testing and process controls

  8. Type of Speech Material Affects Acceptable Noise Level Test Outcome

    Koch, Xaver; Dingemanse, Gertjan; Goedegebure, André; Janse, Esther

    2016-01-01

    The acceptable noise level (ANL) test, in which individuals indicate what level of noise they are willing to put up with while following speech, has been used to guide hearing aid fitting decisions and has been found to relate to prospective hearing aid use. Unlike objective measures of speech perception ability, ANL outcome is not related to individual hearing loss or age, but rather reflects an individual’s inherent acceptance of competing noise while listening to speech. As such, the measu...

  9. Type of speech material affects Acceptable Noise Level test outcome

    Xaver eKoch; Gertjan eDingemanse; André eGoedegebure; Esther eJanse

    2016-01-01

    The Acceptable Noise Level (ANL) test, in which individuals indicate what level of noise they are willing to put up with while following speech, has been used to guide hearing aid fitting decisions and has been found to relate to prospective hearing aid use. Unlike objective measures of speech perception ability, ANL outcome is not related to individual hearing loss or age, but rather reflects an individual's inherent acceptance of competing noise while listening to speech. As such, the measu...

  10. 105K West Isolation Barrier Acceptance Test results

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KW/100K. The tests were performed in accordance with the test plan and acceptance test procedure. The test report contains the test data. This document compares the test data against the criteria. A discussion of the leak rate analytical characterization describes how the flow characteristics flow rate will be determined using the test data from the test report. Two modes of water loss were considered; basin and/or discharge chute leakage, and evaporation. An initial test established baseline leakage data and instrumentation performance. Test 2 evaluated the sealing performance of the isolation barrier by inducing an 11 in. (27.9 cm) level differential across the barrier. The leak rate at this 11 in. (27.9 cm) level is extrapolated to the 16 ft. (4.9 m) level differential postulated in the DBE post seismic event. If the leak rate, adjusted for evaporation and basin leakage (determined from Test 1), is less than the SAR limit of 1,500 gph (5,680 lph) at a 16 ft (4.9 m) level differential, the barriers pass the acceptance test

  11. Initial acceptance test experience with FFTF plant equipment

    The purpose of this paper is to examine the initial acceptance test experience of certain pieces of auxiliary equipment of the Fast Flux Test Facility (FFTF). The scope focuses on the DHX blowers and drive train, inert gas blowers, H and V containment isolation valves, and the Surveillance and In-service Inspection (SISI) transporter and trolley. For each type of equipment, the discussion includes a summary of the design and system function, installation history, preoperational acceptance testing procedures and results, and unusual events and resolutions

  12. Acceptance testing of fluoroscopy systems used for interventional purposes

    This study presents the results of acceptance testing on 18 interventional fluoroscopy systems in Ireland. Acceptance testing and routine quality assurance (QA) of X-ray systems are the requirements of the EU Medical Exposures Directive (MED) and these requirements were subsequently implemented into Irish legislation. The MED states that special consideration should be given to the QA and dose assessment of high dose procedures such as interventional fluoroscopy. Owing to the advances in fluoroscopy technology, it has been found that comprehensive testing of interventional systems proves challenging in a busy hospital environment. A number of recurrent problems have been identified and are presented. (authors)

  13. Automated Acceptance Testing : Why and How to Implement?

    Muroma, Sebastian

    2015-01-01

    The goal of this thesis was to investigate why manual acceptance tests should be automated in a software project and how the automation should be carried out. The topic is of relevance because automated testing is one way to improve the quality of software. Different methods, procedures, types and tools can be used to create automated testing. The challenges of automated testing are implementation, setting the right objectives and choosing the right tool. The benef...

  14. Acceptance test report, plutonium finishing plant life safety upgrade

    Hodge, S.G.

    1994-12-02

    This acceptance Test Procedure (ATP) has been prepared to demonstrate that modifications to the Fir Protection systems function as required by project criteria. The ATP will test the Fire Alarm Control Panels, Flow Alarm Pressure Switch, Heat Detectors, Smoke Detectors, Flow Switches, Manual Pull Stations, and Gong/Door By Pass Switches.

  15. Acceptance test report for portable exhauster POR-007/Skid E

    This document describes Acceptance Testing performed on Portable Exhauster POR-007/Skid E. It includes measurements of bearing vibration levels, pressure decay testing, programmable logic controller interlocks, high vacuum, flow and pressure control functional testing. The purpose of Acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-0490, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuum exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document

  16. Multiport riser and flange assemblies acceptance test report

    This document presents the results of the acceptance test for the multiport riser (MPR) and multiport flange (MPF) assemblies. The accepted MPR and MPF assemblies will be used in support of the hydrogen mitigation project for double-shell waste tank 241-SY-101 and other related projects. The testing described in this document verifies that the mechanical and interface features are operating as designed and that the unit is ready for field service. The objectives of the acceptance testing were as follows: Basic equipment functions and mechanical interfaces were verified; Installation and removal of equipment were demonstrated to the degree possible; Operation of the decon spray system and all valving was confirmed; and the accumulated leak rate of the MPR and MPF assemblies was determined

  17. Acceptance test for graphite components and construction status of HTTR

    In March, 1991, the Japan Atomic Energy Research Institute (JAERI) started to constructed the High Temperature engineering Test Reactor(HTTR) which is a 30-MW(thermal) helium gas-cooled reactor with a core composed of prismatic graphite blocks piled on the core support graphite structures. Two types of graphite materials are used in the HTTR. One is the garde IG-110, isotropic fine grain graphite, another is the grade PGX, medium-to-fine grained molded graphite. These materials were selected on the basis of the appropriate properties required by the HTTR reactor design. Industry-wide standards for an acceptance test of graphite materials used as main components of a nuclear reactor had not been established. The acceptance standard for graphite components of the HTTR, therefore, was drafted by JAERI and reviewed by specialists outside JAERI. The acceptance standard consists of the material testing, non-destructive examination such as the ultrasonic and eddy current testings, dimensional and visual inspections and assembly test. Ultrasonic and eddy current testings are applied to graphite logs to detect an internal flaw and to graphite components to detect a surface flaw, respectively. The assembly test is performed at the works, prior to their installation in the reactor pressure vessel, to examine fabricating precision of each component and alignment of piled-up structures. The graphite components of the HTTR had been tested on the basis of the acceptance standard. It was confirmed that the graphite manufacturing process was well controlled and high quality graphite components were provided to the HTTR. All graphite components except for the fuel graphite blocks are to be installed in the reactor pressure vessel of the HTTR in September 1995. The paper describes the construction status of the HTTR focusing on the graphite components. The acceptance test results are also presented in this paper. (author). Figs

  18. ENRAF Series 854 Advanced Technology Gauge (ATG) Acceptance Test Procedure

    This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer's instructions and specifications and is properly setup prior to being delivered to the tank farm area. This ATP does not set up the gauge for any specific tank, but is generalized to permit testing the gauge prior to installation package preparation

  19. SEP BIMOD variable conductance heat pipes acceptance and characterization tests

    Hemminger, J. A.

    1981-08-01

    A series of six heat pipes, similar in design to those flown on the Comunications Technology Satellite Hermes, for use in a prototype Solar Electric Propulsion BIMOD thrust module are evaluated. The results of acceptance and characterization tests performed on the heat pipe subassemble are reported. The performance of all the heat pipes met, or exceeded, design specifications.

  20. Acceptance test report MICON software exhaust fan control modifications

    This report documents the results the acceptance test HNF-4108 which verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, the alarms for the new emergency fan damper backup air compressor, and the generator sequencer logic

  1. Automatically generated acceptance test: A software reliability experiment

    Protzel, Peter W.

    1988-01-01

    This study presents results of a software reliability experiment investigating the feasibility of a new error detection method. The method can be used as an acceptance test and is solely based on empirical data about the behavior of internal states of a program. The experimental design uses the existing environment of a multi-version experiment previously conducted at the NASA Langley Research Center, in which the launch interceptor problem is used as a model. This allows the controlled experimental investigation of versions with well-known single and multiple faults, and the availability of an oracle permits the determination of the error detection performance of the test. Fault interaction phenomena are observed that have an amplifying effect on the number of error occurrences. Preliminary results indicate that all faults examined so far are detected by the acceptance test. This shows promise for further investigations, and for the employment of this test method on other applications.

  2. Acceptance Test Plan for Fourth-Generation Corrosion Monitoring Cabinet

    This Acceptance Test Plan (ATP) will document the satisfactory operation of the third-generation corrosion monitoring cabinet (Hiline Engineering Part No.0004-CHM-072-C01). This ATP will be performed by the manufacturer of the cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinet. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation

  3. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA, JUNE 2006

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION NEVADA SITE OFFICE

    2006-06-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal.

  4. Specification and acceptance testing of radiotherapy treatment planning systems

    Quality assurance (QA) in the radiation therapy treatment planning process is essential to ensure accurate dose delivery to the patient and to minimize the possibility of accidental exposure. The computerized radiotherapy treatment planning systems (RTPSs) are now widely available in industrialized and developing countries and it is of special importance to support hospitals in Member States in developing procedures for acceptance testing, commissioning and QA of their RTPSs. Responding to these needs, a group of experts developed an IAEA publication with such recommendations, which was published in 2004 as IAEA Technical Reports Series No. 430. This report provides a general framework and describes a large number of tests and procedures that should be considered by the users of new RTPSs. However, small hospitals with limited resources or large hospitals with high patient load and limited staff are not always able to perform complete characterization, validation and software testing of algorithms used in RTPSs. Therefore, the IAEA proposed more specific guidelines that provide a step-by-step recommendation for users at hospitals or cancer centres how to implement acceptance and commissioning procedures for newly purchased RTPSs. The current publication was developed in the framework of the Coordinated Research Project on Development of Procedures for Quality Assurance for Dosimetry Calculations in Radiotherapy and uses the International Electrotechnical Commission (IEC) standard IEC 62083, Requirements for the Safety of Radiotherapy Treatment Planning Systems as its basis. The report addresses the procedures for specification and acceptance testing of RTPSs to be used by both manufacturers and users at the hospitals. Recommendations are provided for specific tests to be performed at the manufacturing facility known as type tests, and for acceptance tests to be performed at the hospital known as site tests. The purpose of acceptance testing is to demonstrate to the

  5. Startup of the FFTF sodium cooled reactor. [Acceptance Test Program

    Redekopp, R.D.; Umek, A.M.

    1981-03-01

    The Fast Flux Test Facility (FFTF), located on the Department of Energy (DOE) Hanford Reservation near Richland, Washington, is a 3 Loop 400 MW(t) sodium cooled fast reactor with a primary mission to test fuels and materials for development of the Liquid Metal Fast Breeder Reactor (LMFBR). Bringing FFTF to a condition to accomplish this mission is the goal of the Acceptance Test Program (ATP). This program was the mechanism for achieving startup of the FFTF. Highlights of the ATP involving the system inerting, liquid metal and inerted cell testing and initial ascent to full power are discussed.

  6. Swiss requirements concerning gamma camera acceptance and status testing

    Like in the field of radiology, digital systems are also becoming the standard in the field of nuclear medicine. This offers not only the possibility to process, transmit and archive data from patients more easily but also to introduce quantitative measurements for quality controls. In this framework standards concerning the qualification of gamma camera systems have been updated and appeared to be useful to set legal requirements, in spite of the fact that this is not their goal. The aim of this study was first to choose a set of tests described in standards to define measurements to be performed at the acceptance of the systems, after the regular maintenances (at least once every six months; status test) and for assuring the stability of the systems. To verify the feasibility, from the point of view of technical and a time requirements, the quality assurance programme proposed has been applied on three gamma camera systems. The results of this study show that, based on international standards, new requirements concerning the quality assurance of the gamma camera of the Swiss Public Health Authority make it necessary to slightly modify some procedures to reduce the time required for the acceptance and status tests. In the Ordinance related to the use of unsealed radioactive sources (November 1997) the Swiss Public Health Authority requires the supplier to carry out a reception test on all imaging devices used in the field of nuclear medicine before they can be used on patients. Moreover, a maintenance procedure of the imaging device has to be performed at least every six months by properly trained staff. This maintenance has to be followed by a status test that assures the integrity of the system before it can be used for further clinical applications. Daily and weekly stability tests, under the responsibility of the users of the system, are also defined. According to the Swiss Ordinance, all the measurements required for the acceptance and status tests should

  7. Acceptance of genetic testing in a general population

    Aro, A R; Hakonen, A; Hietala, M;

    1997-01-01

    The aim of the study was to analyze effects of age, education and gender on acceptance of genetic testing. Subjects, n = 1967 aged 15-69, were a stratified random sample of the Finnish population. One thousand, one hundred and sixty nine subjects, 530 men and 639 women, returned the questionnaire....... The majority of the respondents approved of the availability of genetic testing. Young, aged 15-24, were more favourable towards testing and more willing to undergo suggested tests, but they were also more worried than others about the misuse of test results. Men aged 45-69 with only basic education...... were more in favour of mandatory genetic testing than other respondents. Respondents with university education were more critical towards genetic testing and expressed their worry about eugenics more often than other education groups. In conclusion, there are age, education and gender related...

  8. Central Acceptance Testing for Camera Technologies for CTA

    Bonardi, A; Chadwick, P; Dazzi, F; Förster, A; Hörandel, J R; Punch, M

    2015-01-01

    The Cherenkov Telescope Array (CTA) is an international initiative to build the next generation ground based very-high energy gamma-ray observatory. It will consist of telescopes of three different sizes, employing several different technologies for the cameras that detect the Cherenkov light from the observed air showers. In order to ensure the compliance of each camera technology with CTA requirements, CTA will perform central acceptance testing of each camera technology. To assist with this, the Camera Test Facilities (CTF) work package is developing a detailed test program covering the most important performance, stability, and durability requirements, including setting up the necessary equipment. Performance testing will include a wide range of tests like signal amplitude, time resolution, dead-time determination, trigger efficiency, performance testing under temperature and humidity variations and several others. These tests can be performed on fully-integrated cameras using a portable setup at the came...

  9. MCO combustible gas management leak test acceptance criteria

    Existing leak test acceptance criteria for mechanically sealed and weld sealed multi-canister overpacks (MCO) were evaluated to ensure that MCOs can be handled and stored in stagnant air without compromising the Spent Nuclear Fuel Project's overall strategy to prevent accumulation of combustible gas mixtures within MCO's or within their surroundings. The document concludes that the integrated leak test acceptance criteria for mechanically sealed and weld sealed MCOs (1 x 10-5 std cc/sec and 1 x 10-7 std cc/sec, respectively) are adequate to meet all current and foreseeable needs of the project, including capability to demonstrate compliance with the NFPA 60 Paragraph 3-3 requirement to maintain hydrogen concentrations [within the air atmosphere CSB tubes] t or below 1 vol% (i.e., at or below 25% of the LFL)

  10. Acceptance test plan for the Waste Information Control System

    Flynn, D.F.

    1994-09-14

    This document describes the acceptance test plan for the WICS system. The Westinghouse Hanford Company (WHC) Hazardous Material Control Group (HMC) of the 222-S Laboratory has requested the development of a system to help resolve many of the difficulties associated with tracking and data collection of containers and drums of waste. This system has been identified as Waste Information and Control System (WICS). The request for developing and implementing WICS has been made to the Automation and Simulation Engineering Group (ASE).

  11. Central Acceptance Testing for Camera Technologies for CTA

    Bonardi, A.; T. Buanes; Chadwick, P.; Dazzi, F.; A. Förster(CERN, Geneva, Switzerland); Hörandel, J. R.; Punch, M.; Consortium, R. M. Wagner for the CTA

    2015-01-01

    The Cherenkov Telescope Array (CTA) is an international initiative to build the next generation ground based very-high energy gamma-ray observatory. It will consist of telescopes of three different sizes, employing several different technologies for the cameras that detect the Cherenkov light from the observed air showers. In order to ensure the compliance of each camera technology with CTA requirements, CTA will perform central acceptance testing of each camera technology. To assist with thi...

  12. Project W-049H Collection System Acceptance Test

    The Acceptance Test Procedure (ATP) Program for Project W-049H covers the following activities: Disposal system, Collection system, Instrumentation and control system. Each activity has its own ATP. The purpose of the ATPs is to verify that the systems have been constructed in accordance with the construction documents and to demonstrate that the systems function as required by the Project criteria. This ATP has been prepared to demonstrate that the Collection System Instrumentation functions as required by project criteria

  13. 242A Distributed Control System Year 2000 Acceptance Test Report

    This report documents acceptance test results for the 242-A Evaporator distributive control system upgrade to D/3 version 9.0-2 for year 2000 compliance. This report documents the test results obtained by acceptance testing as directed by procedure HNF-2695. This verification procedure will document the initial testing and evaluation of the potential 242-A Distributed Control System (DCS) operating difficulties across the year 2000 boundary and the calendar adjustments needed for the leap year. Baseline system performance data will be recorded using current, as-is operating system software. Data will also be collected for operating system software that has been modified to correct year 2000 problems. This verification procedure is intended to be generic such that it may be performed on any D/3(trademark) (GSE Process Solutions, Inc.) distributed control system that runs with the VMSTM (Digital Equipment Corporation) operating system. This test may be run on simulation or production systems depending upon facility status. On production systems, DCS outages will occur nine times throughout performance of the test. These outages are expected to last about 10 minutes each

  14. Acceptance test report for portable exhauster POR-008/Skid F

    Portable Exhauster POR-008 was procured via HNF-0490, Specification for a Portable Exhausted System for Waste Tank Ventilation. Prior to taking ownership, acceptance testing was performed at the vendors. However at the conclusion of testing a number of issues remained that required resolution before the exhausters could be used by Project W-320. The purpose of acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-O49O, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuum exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document

  15. Project W-049H collection system Acceptance Test Procedure

    The purpose of this Acceptance Test Procedure (ATP) for the Project W-049H, Treated Effluent Disposal Facility, is to verify that the collection system equipment installed as Pump Station No. 1 (225-W) and Pump Station No. 2 (225-E) have been installed in accordance with the design documents and function as required by the project criteria. This will be a wet test with potable water being introduced into the pump pits to test for leakage. Potable water will also be employed in the testing of the pumps and related mechanical equipment. All Instrument and Control equipment related to the pump stations will be checked electronically with simulated inputs/outputs when actual input/output signals are unavailable. Water from Pump Station 1 will be moved through the TEDF piping system and discharged into the disposal ponds. This will check the proper function of the air/vac valves not tested during construction, and the automated samplers

  16. Project W-049H instrument and control Acceptance Test Procedure

    The purpose of this Acceptance Test Procedure (ATP) for the Project W-049H, Treated Effluent Disposal Facility, is to verify that the instrument and control systems have been installed in accordance with the design documents and function as required by the project criteria. The instrument and control system includes three operator control stations, modems, and general purpose LAN interface cabinets in the Effluent Treatment Facility control room; two pump stations; disposal station pumping building; and all local control units installed in the fold. Testing will be performed using actual signals when available and simulated signals when actual signals are unavailable

  17. Planning and acceptance testing of MV therapy installations

    Purpose: This course is designed for practitioners and beginners in brachytherapy. The aim is to review biological principles equipment are aware of all aspects involved. The object is to cover in a broad overview the considerations that go into selecting, installing, testing and accepting megavoltage therapy equipment and to provide a resource for more detailed information. Planning and acceptance testing of a megavoltage therapy installation is a major undertaking for any size group, institution or department. It can take approximately two years from the time a decision is made to get a machine to where the first patient is treated. Because the equipment and site preparation are expensive, and most of the machines are complex and can be supplied by several different manufacturers, it is imperative that a great deal of thought and care go into the decision: the aim being that the specifications of the machine that is installed meet the immediate need of the department and the needs for the projected lifetime of the equipment. A general survey of the types of equipment available will be presented. This will concentrate on general purpose linear accelerators, although Cobalt 60 machines, microtrons and special purpose machines (intra-operative equipment) will also be covered. General descriptions of the machines along with typical specifications will be given. Selecting the best machine to meet specific needs can be quite complex and criteria for making the selection are presented in a series of twelve steps. site selection and room design, including the console area, are also critical. The general principles for shielding calculations will be provided. Critical to any installation is the acceptance testing of the equipment including material and radiation oncology performance tests. These tests will be outlined. A reading list of suitable references describing in detail many of the aspects of this course will be provided

  18. Planning and acceptance testing of Mv therapy installations

    Purpose/Objective: The purpose of this course is to ensure that the individuals responsible for acquiring megavoltage therapy equipment are aware of all aspects involved. The object is to cover in a broad overview the considerations that go into selecting, installing, testing and accepting megavoltage therapy equipment and to provide a resource for more detailed information. Planning and acceptance testing of a megavoltage therapy installation is a major undertaking for any size group, institution or department. It can take approximately two years from the time a decision is made to get a machine to where the first patient is treated. Because the equipment and site preparation are expensive, and most of the machines are complex and can be supplied by several different manufacturers, it is imperative that a great deal of thought and care go into the decision: the aim being that the specifications of the machine that is installed meet the immediate need of the department and the needs for the projected lifetime of the equipment. A general survey of the types of equipment available will be presented. This will concentrate on general purpose linear accelerators, although Cobalt 60 machines, microtrons and special purpose machines (intra-operative equipment) will also be covered. General descriptions of the machines along with typical specifications will be given. Selecting the best machine to meet specific needs can be quite complex and criteria for making the selection are presented in a series of twelve steps. Site selection and room design, including the console area, are also critical. The general principles for shielding calculations will be provided. Critical to any installation is the acceptance testing of the equipment including material and radiation oncology performance tests. These tests will be outlined. A reading list of suitable references describing in detail many of the aspects of this course will be provided

  19. Planning and acceptance testing of MV therapy installations

    Purpose/Objective: The purpose of this course is to ensure that the individuals responsible for acquiring megavoltage therapy equipment are aware of all aspects involved. The object is to cover in a broad overview the considerations that go into selecting, installing, testing and accepting megavoltage therapy equipment and to provide a resource for more detailed information. Planning and acceptance testing of a megavoltage therapy installation is a major undertaking for any size group, institution or department. It can take approximately two years from the time a decision is made to get a machine to where the first patient is treated. Because the equipment and site preparation are expensive, and most of the machines are complex and can be supplied by several different manufacturers, it is imperative that a great deal of thought and care go into the decision: the aim being that the specifications of the machine that is installed meet the immediate need of the department and the needs for the projected lifetime of the equipment. A general survey of the types of equipment available will be presented. This will concentrate on general purpose linear accelerators, although Cobalt 60 machines, microtrons and special purpose machines (intra-operative equipment) will also be covered. General descriptions of the machines along with typical specifications will be given. Selecting the best machine to meet specific needs can be quite complex and criteria for making the selection are presented in a series of twelve steps. Site selection and room design, including the console area, are also critical. The general principles for shielding calculations will be provided. Critical to any installation is the acceptance testing of the equipment including material and radiation oncology performance tests. These tests will be outlined. A reading list of suitable references describing in detail many of the aspects of this course will be provided

  20. Nevada Test Site waste acceptance criteria [Revision 1

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  1. Nevada Test Site waste acceptance criteria [Revision 1

    None

    1997-08-01

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

  2. Acceptance test report for project C-157 ''T-Plant electrical upgrade''

    This Acceptance Test Report (ATR) documents for record purposes the field results, acceptance, and approvals of the completed acceptance test per WHC-SD-Cl57-ATP-001, Rev. 0, ''Acceptance Test Proceedure for Project C-157 'T Plant Electrical Upgrade''' The test was completed and approved without any problems or exceptions

  3. Acceptance test plan for fourth generation Hanford corrosion monitoring system

    This Acceptance Test Plan (ATP) will document the satisfactory operation of the corrosion probe cabinets destined for installation on tanks 241-AN-102 and 241-AN-107. This ATP will be performed by the manufacturer on each cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinets to be installed on tanks 241-AN-102 and 241-AN-107. One cabinet will be installed on each tank. Each cabinet will contain corrosion monitoring hardware to be connected to existing corrosion probes already installed in each tank. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation (input a known signal and see if the instrumentation records the proper value)

  4. Acceptance Test Report for Fourth Generation Hanford Corrosion Monitoring System

    This Acceptance Test Report (ATR) will document the satisfactory operation of the corrosion probe cabinets destined for installation on tanks 241-AN-102 and 241-AN-107. This ATR will be performed by the manufacturer on each cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinets to be installed on tanks 241-AN-102 and 241-AN-107. One cabinet will be installed on each tank. Each cabinet will contain corrosion monitoring hardware to be connected to existing corrosion probes already installed in each tank. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation (input a known signal and see if the instrumentation records the proper value)

  5. Acceptance test report: Field test of mixer pump for 241-AN-107 caustic addition project

    The field acceptance test of a 75 HP mixer pump (Hazleton serial number N-20801) installed in Tank 241-AN-107 was conducted from October 1995 thru February 1996. The objectives defined in the acceptance test were successfully met, with two exceptions recorded. The acceptance test encompassed field verification of mixer pump turntable rotation set-up and operation, verification that the pump instrumentation functions within established limits, facilitation of baseline data collection from the mixer pump mounted ultrasonic instrumentation, verification of mixer pump water flush system operation and validation of a procedure for its operation, and several brief test runs (bump) of the mixer pump

  6. Acceptance test report for ENRAF control panel software

    On March 5, 1998, the ENRAF Control Panel Software program was acceptance tested per HNF-1991 Revision 0. The test was performed at the Department of Energy's Hanford Site, 200 West Area, building MO-281. The test validated the functionality of the software for use by project W-320, C-1 06 Retrieval. The purpose of the test procedure was to partially verify the functionality of the ENRAF Control Panel Software. The test cycled through the majority of functions within the program. Functions not tested will be tested per Operational Test Procedure OTP-320-01 0 at a later date. The following criteria was used to determine whether the software passed or failed the test. The gauge responds correctly (as described in vendor documentation, Reference 1) to all commands sent through the program. If gauge related error codes are encountered, they may be cleared either through the PET or the program. However, the program, while running, must provide some indication of all gauge related errors encountered. If any of the pass criteria are not met and cannot be immediately resolved. If the system crashes for reasons that are clearly related to program performance and cannot be immediately resolved

  7. Acceptability of prenatal testing and termination of pregnancy in Pakistan.

    Jafri, H; Hewison, J; Sheridan, E; Ahmed, S

    2015-01-01

    This study aimed to assess acceptability of prenatal testing (PNT) and termination of pregnancy (TOP) for a range of conditions in Pakistani parents with and without a child with a genetic condition. A structured questionnaire assessing acceptability of PNT and TOP for 30 conditions was completed by 400 Pakistani participants: 200 parents with a child with a genetic condition (100 fathers and 100 mothers) and 200 parents without an affected child (100 fathers and 100 mothers). There was a high level of interest in PNT, where over 80 % of parents in all four study groups would want PNT for the majority of the conditions. There was comparatively less interest in TOP for the same conditions (ranging from 5 to 70 % of parents, with mothers of an affected child being most interested). Parents were most likely to be interested in TOP for conditions at the serious end of the continuum. More than half of the participants in each group would consider TOP for anencephaly and quadriplegia. The interest in PNT and TOP for a range of conditions suggests that rapidly developing PNT technologies are likely to be acceptable in Pakistan, a low-middle income level and Muslim country. The comparatively lower level of interest in TOP for the same conditions highlights ethical dilemmas that such technologies are likely to raise. PMID:25081227

  8. Could quantitative liver function tests gain wide acceptance among hepatologists?

    Giovanni Tarantino

    2009-01-01

    It has been emphasized that the assessment of residual liver function is of paramount importance to determine the following: severity of acute or chronic liver diseases independent of etiology; long-term prognosis; step-bystep disease progression; surgical risk; and efficacy of antiviral treatment. The most frequently used tools are the galactose elimination capacity to asses hepatocyte cytosol activity, plasma clearance of indocyanine green to assess excretory function, and antipyrine clearance to estimate microsomal activity. However, a widely accepted liver test (not necessarily a laboratory one) to assess quantitative functional hepatic reserve still needs to be established, although there have been various proposals. Furthermore, who are the operators that should order these tests? Advances in analytic methods are expected to allow quantitative liver function tests to be used in clinical practice.

  9. [Clinical trial data validation and user acceptance testing].

    Sun, Hua-long; Dai, Nan

    2015-11-01

    For pharmaceutical industries, clinical data is one of the most valuable deliverables. It is also the basis of analysis, submission, approval, labeling and marketing of a drug product. To ensure the integrity and reliability of clinical data, a scientific standardized quality control (QC) has to be established at each step of a clinical trial. Data validation is conducted to ensure the reasonability and compliance of clinical data by checking data quality before the data is statistically analyzed. This paper focuses on purpose of data validation, creation of data validation plan, rationale of data validation, types of data validation and performance of user acceptance testing on clinical database. PMID:26911047

  10. Acceptance testing and quality assurance of Simulix evolution radiotherapy simulator

    The success of radiotherapy depends on precise treatment simulation and proper patient positioning. The simulator is a conventional radiographic and fluoroscopic system which emulates the geometrical positions of radiotherapy treatment unit. Hence, the acceptance tests and quality assurance (QA) of the simulator are important prior to its commissioning for the safe and precise clinical use. The verification of mechanical and optical readouts, field size, isocenter, optical and radiation field congruence were performed. The X-ray beam parameters were tested for kVp, mAs and consistency of radiation output. The flat panel detector performance was checked with respect to resolution, low contrast sensitivity (LCS), automatic dose rate control (ADRC), and gray image resolution (GIR). Gantry, table, and imaging system collision possibility was checked. Radiation survey around the room was also performed. The field size test for digital readout and on graph paper, the results of isocenter checkup for rotation of gantry, collimator, and couch, and the deviations observed in auto stop for various movements were found within the tolerance limits. Optical field and radiation field was found congruent. All the lasers were found aligned with the established isocenter. Maximum deviation for set and measured kV was found to be 3% in fluoro mode. The maximum deviation observed in mAs was 1.5% in 3-point as well as in 2-point film exposed mode. The X-ray output was found consistent. The results of tests for resolution, LCS, ADRC, and GIR of the flat panel detector were within tolerance limits. All the six safety interlocks were found working. Radiation level around the room was found within the acceptable limits. All the tests carried out were found within the tolerance limits. The data which has been taken in this study will provide basic support to the routine QA of the simulator. (author)

  11. Test Report for Acceptance Test Procedure for Pumping and Instrumentation Control Skid ''K''

    This is a Test Report for Acceptance Test Procedure (ATP) HNF-4276. This test report provides the results of the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''K''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  12. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  13. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid N

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5489. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''N''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  14. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid M

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5073. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''M''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document

  15. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid L

    KOCH, M.R.

    1999-11-09

    This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

  16. Test Report for Acceptance Test Procedure for Pumping and Instrumentation Control Skid ''K''

    Johns, B R

    1999-01-01

    This is a Test Report for Acceptance Test Procedure (ATP) HNF-4276. This test report provides the results of the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''K''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

  17. Topographical mapping system for radiological and hazardous environments acceptance testing

    During the summer of 1996, the Topographical Mapping System (TMS) for hazardous and radiological environments and its accompanying three-dimensional (3-D) visualization tool, the Interactive Computer-Enhanced Remote-Viewing System (ICERVS), were delivered to Oak Ridge National Laboratory (ORNL). ORNL and Mechanical Technology, Inc., performed final acceptance testing of the TMS during the next eight months. The TMS was calibrated and characterized during this period. This paper covers the calibration, characterization, and acceptance testing of the TMS. Development of the TMS and ICERVS was initiated by the US Department of Energy (DOE) for the purpose of characterization and remediation of underground storage tanks (USTs) at DOE sites across the country. DOE required a 3-D, topographical mapping system suitable for use in hazardous and radiological environments. The intended application is the mapping of the interior of USTs as part of DOE's waste characterization and remediation efforts and to obtain baseline data on the content of the storage tank interiors as well as data on changes in the tank contents and levels brought about by waste remediation steps. Initially targeted for deployment at the Hanford Washington site, the TMS is designed to be a self-contained, compact, and reconfigurable system that is capable of providing rapid, variable-resolution mapping information in poorly characterized workspaces with a minimum of operator intervention

  18. Type of speech material affects Acceptable Noise Level test outcome

    Xaver eKoch

    2016-02-01

    Full Text Available The Acceptable Noise Level (ANL test, in which individuals indicate what level of noise they are willing to put up with while following speech, has been used to guide hearing aid fitting decisions and has been found to relate to prospective hearing aid use. Unlike objective measures of speech perception ability, ANL outcome is not related to individual hearing loss or age, but rather reflects an individual's inherent acceptance of competing noise while listening to speech. As such, the measure may predict aspects of hearing aid success. Crucially, however, recent studies have questioned its repeatability (test-retest reliability. The first question for this study was whether the inconsistent results regarding the repeatability of the ANL test may be due to differences in speech material types used in previous studies. Second, it is unclear whether meaningfulness and semantic coherence of the speech modify ANL outcome. To investigate these questions, we compared ANLs obtained with three types of materials: the International Speech Test Signal (ISTS, which is non-meaningful and semantically non-coherent by definition, passages consisting of concatenated meaningful standard audiology sentences, and longer fragments taken from conversational speech. We included conversational speech as this type of speech material is most representative of everyday listening. Additionally, we investigated whether ANL outcomes, obtained with these three different speech materials, were associated with self-reported limitations due to hearing problems and listening effort in everyday life, as assessed by a questionnaire. ANL data were collected for 57 relatively good-hearing adult participants with an age range representative for hearing aid users. Results showed that meaningfulness, but not semantic coherence of the speech material affected ANL. Less noise was accepted for the non-meaningful ISTS signal than for the meaningful speech materials. ANL repeatability was

  19. Type of Speech Material Affects Acceptable Noise Level Test Outcome.

    Koch, Xaver; Dingemanse, Gertjan; Goedegebure, André; Janse, Esther

    2016-01-01

    The acceptable noise level (ANL) test, in which individuals indicate what level of noise they are willing to put up with while following speech, has been used to guide hearing aid fitting decisions and has been found to relate to prospective hearing aid use. Unlike objective measures of speech perception ability, ANL outcome is not related to individual hearing loss or age, but rather reflects an individual's inherent acceptance of competing noise while listening to speech. As such, the measure may predict aspects of hearing aid success. Crucially, however, recent studies have questioned its repeatability (test-retest reliability). The first question for this study was whether the inconsistent results regarding the repeatability of the ANL test may be due to differences in speech material types used in previous studies. Second, it is unclear whether meaningfulness and semantic coherence of the speech modify ANL outcome. To investigate these questions, we compared ANLs obtained with three types of materials: the International Speech Test Signal (ISTS), which is non-meaningful and semantically non-coherent by definition, passages consisting of concatenated meaningful standard audiology sentences, and longer fragments taken from conversational speech. We included conversational speech as this type of speech material is most representative of everyday listening. Additionally, we investigated whether ANL outcomes, obtained with these three different speech materials, were associated with self-reported limitations due to hearing problems and listening effort in everyday life, as assessed by a questionnaire. ANL data were collected for 57 relatively good-hearing adult participants with an age range representative for hearing aid users. Results showed that meaningfulness, but not semantic coherence of the speech material affected ANL. Less noise was accepted for the non-meaningful ISTS signal than for the meaningful speech materials. ANL repeatability was comparable across

  20. Loss on Ignition Furnace Acceptance and Operability Test Procedure

    JOHNSON, D.C.

    2000-06-01

    The purpose of this Acceptance Test Procedure and Operability Test Procedure (ATP/OTP)is to verify the operability of newly installed LOI equipment, including a model 1608FL CM{trademark} Furnace, a dessicator, and balance. The operability of the furnace will be verified. The arrangement of the equipment placed in Glovebox 157-3/4 to perform Loss on Ignition (LOI) testing on samples supplied from the Thermal Stabilization line will be verified. In addition to verifying proper operation of the furnace, this ATP/OTP will also verify the air flow through the filters, verify a damper setting to establish and maintain the required differential pressure between the glovebox and the room pressure, and test the integrity of the newly installed HEPA filter. In order to provide objective evidence of proper performance of the furnace, the furnace must heat 15 crucibles, mounted on a crucible rack, to 1000 C, according to a program entered into the furnace controller located outside the glovebox. The glovebox differential pressure will be set to provide the 0.5 to 2.0 inches of water (gauge) negative pressure inside the glovebox with an airflow of 100 to 125 cubic feet per minute (cfm) through the inlet filter. The glovebox inlet Glfilter will he flow tested to ensure the integrity of the filter connections and the efficiency of the filter medium. The newly installed windows and glovebox extension, as well as all disturbed joints, will be sonically tested via ultra probe to verify no leaks are present. The procedure for DOS testing of the filter is found in Appendix A.

  1. Acceptance test procedure for Project W-049H

    The Acceptance Test Procedure (ATP) program for Project W-049H (200 Area Treated Effluent Disposal Facility [TEDF]) covers three activities as follows: (1) Disposal System; (2) Collection System; and (3) Instrumentation and Control System. Each activity has its own ATP. The purpose of the ATPs is to reverify that the systems have been constructed in accordance with the construction documents and to demonstrate that the systems function as required by the Project criteria. The Disposal System ATP covers the testing of the following: disposal line flowmeters, room air temperatures in the Disposal Station Sampling Building, effluent valves and position indicators, disposal pond level monitors, automated sampler, pressure relief valves, and overflow diversion sluice gates. The Collection System ATP covers the testing of the two pump stations and all equipment installed therein. The Instrumentation and Control (I and C) ATP covers the testing of the entire TEDF I and C system. This includes 3 OCS units, modem, and GPLI cabinets in the ETC control room; 2 pump stations; disposal station sampling building; and all LCUs installed in the field

  2. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid ''P''

    This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix

  3. Test Report for Acceptance Test Procedure for Pumping Instrumentation and Control Skid Q

    This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix

  4. Test marketing and consumer acceptance of irradiated meat products

    This study consists of two parts: irradiation processing of cooked meat and irradiation preservation of prepackaged chilled fresh cut meats. Irradiation of prepackaged pickled meat products dipped in grains stillage at a dose 6-8 kGy eliminated common food-borne microorganisms, such as E. Coli and other microbial pathogens and extended the shelf life of the product to 10 days at 5 deg. C. Test marketing of 40,000 bags (about 10,000 kg) of the product in more than 100 supermarkets in the city of Shanghai showed no untoward problem with consumer acceptance. Irradiation of prepackaged chilled fresh cut pork at a dose 3 kGy led to inactivation of microbial pathogens and parasites with a concomitant reduction in numbers of common spoilage microorganisms and extension of shelf life of the product for 30 days at 5 deg. C. The cost benefit and marketing applications were evaluated. (author)

  5. Acceptance testing and commissioning of a new model HDR afterloader

    We have recently performed acceptance testing procedures and have commissioned a new model HDR afterloader, the Varian VariSource with ''Intelligent Drive.'' Our site was one of the first installations worldwide. It is our intent to describe our tests and the results of the tests particularly as they may differ from other afterloaders. The Ir-192 source is unique among afterloaders marketed in the US in that it is very slender (OD of source wire is 0.59 mm) and relatively long (two 0.5 cm sources for a total active length of 1.0 cm). A check of source homogeneity by autoradiograph as urged by the US Nuclear Regulatory Commission demonstrates no detectable source inhomogeneity. Reentrant well ionization chambers are calibrated in the US with a 3.5 mm long source at Accredited Dosimetry Calibration Laboratories. Therefore calibration needs to be considered with some care. Calibration of the first delivered source with a well ionization chamber indicated agreement with the manufacturer's stated activity to within 0.5%. Source positioning is checked with a device called a 'cam scale'. Tests have been carried out on this system and it has been found to accurately indicate source position to within ±0.5 mm. Timer accuracy has been found to be better than 0.1% for dwell times of several hundred seconds. The intelligent drive system and the small source diameter allow the source wire to negotiate paths with small radius of curvature. A series of tests have been made in which the source is forced to negotiate 'U' turns of decreasing radius of curvature. A 4.7 F, 100 cm long catheter was used for these tests and the 'U' turn was positioned at approximately 90 cm. Under these conditions, the VariSource was consistently able to traverse a 1.25 cm radius of curvature, which is better than the manufacturer's stated limit of 1.5 cm

  6. Acceptance test of graphite components in nuclear reactor

    The HTTR is the first high temperature gas-cooled reactor in Japan. It is a test reactor with thermal power of 30 MW and coolant outlet temperature of 950degC at maximum. To achieve high temperature coolant core internals were made of graphite and carbon materials due to their excellent thermal resistivity. After fabrication of graphite and carbon components at works they were installed in the HTTR, and now it is in the power up testing stage. Concerning the inspection standard of the graphite and carbon components, nondomestic standard exists as main components in the nuclear reactor. It is necessary, therefore, to prescribe the inspection standards for the HTTR graphite components. Many research and developments in relation to the inspection standard, e.g. in the research field of nondestructive examination of the graphite material, had been performed, and then the JAERI established the inspection standard. The acceptance test of the graphite and carbon components was carried out based on the inspection standard. This paper prescribes the outline of the established inspection standard. (author)

  7. Acceptance test report, 241-SY-101 Flexible Receiver System, Phase 3 testing

    This document summarizes the results of the phase 3 acceptance test of the 241-SY-101 Flexible Receiver System (FRS). The purpose of this acceptance test is to verify the sealing integrity of the FRS to ensure that the release of waste and aerosols will be minimized during the removal of the test mixer pump from Tank 241-SY-101. The FRS is one of six major components of the Equipment Removal System, which has been designed to retrieve, transport, and store the mixer pump. This acceptance test was performed at the 306E Facility in the 300 area from January 10, 1995 to January 17, 1995. The Phase 3 test consisted of two parts. Part one was a water leak test of the seal between the blast shield and mock load distribution frame (LDF) to ensure that significant contamination of the pump pit and waste interaction with the aluminum impact-limiting material under the LDF are prevented during the pump removal operation. The second part of this acceptance test was an air leak test of the assembled flexible receiver system. The purpose of this test was to verify that the release of hazardous aerosols will be minimized if the tank dome pressure becomes slightly positive during the decontamination of the mixer pump

  8. ISOLOK VALVE ACCEPTANCE TESTING FOR DWPF SME SAMPLING PROCESS

    Edwards, T.; Hera, K.; Coleman, C.; Jones, M.; Wiedenman, B.

    2011-12-05

    Evaluation of the Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. Of the opportunities, a focus area related to optimizing the equipment and efficiency of the sample turnaround time for DWPF Analytical Laboratory was identified. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) evaluated the possibility of using an Isolok{reg_sign} sampling valve as an alternative to the Hydragard{reg_sign} valve for taking process samples. Previous viability testing was conducted with favorable results using the Isolok sampler and reported in SRNL-STI-2010-00749 (1). This task has the potential to improve operability, reduce maintenance time and decrease CPC cycle time. This report summarizes the results from acceptance testing which was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 (2) and which was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNL-RP-2011-00145 (3). The Isolok to be tested is the same model which was tested, qualified, and installed in the Sludge Receipt Adjustment Tank (SRAT) sample system. RW-0333P QA requirements apply to this task. This task was to qualify the Isolok sampler for use in the DWPF Slurry Mix Evaporator (SME) sampling process. The Hydragard, which is the current baseline sampling method, was used for comparison to the Isolok sampling data. The Isolok sampler is an air powered grab sampler used to 'pull' a sample volume from a process line. The operation of the sampler is shown in Figure 1. The image on the left shows the Isolok's spool extended into the process line and the image on the right shows the sampler retracted and then dispensing the liquid into the sampling container. To determine tank homogeneity, a Coliwasa sampler was used to grab samples at a high and low location within the mixing tank. Data from

  9. Isolok Valve Acceptance Testing For DWPF SME Sampling Process

    Evaluation of the Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. Of the opportunities, a focus area related to optimizing the equipment and efficiency of the sample turnaround time for DWPF Analytical Laboratory was identified. The Mechanical Systems and Custom Equipment Development (MS and CED) Section of the Savannah River National Laboratory (SRNL) evaluated the possibility of using an Isolok(regsign) sampling valve as an alternative to the Hydragard(regsign) valve for taking process samples. Previous viability testing was conducted with favorable results using the Isolok sampler and reported in SRNL-STI-2010-00749 (1). This task has the potential to improve operability, reduce maintenance time and decrease CPC cycle time. This report summarizes the results from acceptance testing which was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 (2) and which was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNL-RP-2011-00145 (3). The Isolok to be tested is the same model which was tested, qualified, and installed in the Sludge Receipt Adjustment Tank (SRAT) sample system. RW-0333P QA requirements apply to this task. This task was to qualify the Isolok sampler for use in the DWPF Slurry Mix Evaporator (SME) sampling process. The Hydragard, which is the current baseline sampling method, was used for comparison to the Isolok sampling data. The Isolok sampler is an air powered grab sampler used to 'pull' a sample volume from a process line. The operation of the sampler is shown in Figure 1. The image on the left shows the Isolok's spool extended into the process line and the image on the right shows the sampler retracted and then dispensing the liquid into the sampling container. To determine tank homogeneity, a Coliwasa sampler was used to grab samples at a high and low location within the mixing tank. Data from the two

  10. Overcoming Denial through the Group: A Test of Acceptance Theory.

    Rugel, Robert P.; Barry, Denise

    1990-01-01

    Found participants (N=28) in alcohol treatment groups showed decreases in denial of drinking problems and decreases in psychopathology following 12 weeks of group counseling. Determined greater self-acceptance was associated with experiencing acceptance by group and with greater decreases in denial; decreases in denial and psychopathology were…

  11. Specification and acceptance testing of nuclear medicine equipment

    The purchase of nuclear medicine equipment is of prime importance in the operation of a clinical service. Failure to properly evaluate the potential uses of the instrumentation and the various operational characteristics of the equipment can often result in the purchase of inappropriate or inferior instruments. The magnitude of the purchase in terms of time and financial investments make it imperative that the purchase be approached in a systematic manner. Consideration of both the intended clinical functions and personnel requirements is important. It is necessary also to evaluate the ability of the equipment vendor to support the instrumentation after the purchase has been completed and the equipment installed in the clinical site. The desired specifications of the instrument characteristics should be stated in terms that can be verified by acceptance testing. The complexity of modern instrumentation and the sensitivity of it to the environment require the buyer to take into account the potential problems of controlling the temperature, humidity, and electrical power of the installation site. If properly and systematically approached, the purchase of new nuclear medicine instrumentation can result in the acquisition of a powerful diagnostic tool which will have a useful lifetime of many years. If not so approached, it may result in the expenditure of a large amount of money and personnel time without the concomitant return in useful clinical service. (author)

  12. Acceptance test procedure for the 105-KW isolation barrier leak rate

    This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals. This Acceptance Test Procedure (ATP) has been prepared in accordance with CM-6-1 EP 4.2, Standard Engineering Practices

  13. Acceptance test procedure for the 105-KW isolation barrier leak rate

    McCracken, K.J.

    1995-05-19

    This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an acceptable leakage rate through the barrier seals. This Acceptance Test Procedure (ATP) has been prepared in accordance with CM-6-1 EP 4.2, Standard Engineering Practices.

  14. In situ vitrification large-scale operational acceptance test analysis

    A thermal treatment process is currently under study to provide possible enhancement of in-place stabilization of transuranic and chemically contaminated soil sites. The process is known as in situ vitrification (ISV). In situ vitrification is a remedial action process that destroys solid and liquid organic contaminants and incorporates radionuclides into a glass-like material that renders contaminants substantially less mobile and less likely to impact the environment. A large-scale operational acceptance test (LSOAT) was recently completed in which more than 180 t of vitrified soil were produced in each of three adjacent settings. The LSOAT demonstrated that the process conforms to the functional design criteria necessary for the large-scale radioactive test (LSRT) to be conducted following verification of the performance capabilities of the process. The energy requirements and vitrified block size, shape, and mass are sufficiently equivalent to those predicted by the ISV mathematical model to confirm its usefulness as a predictive tool. The LSOAT demonstrated an electrode replacement technique, which can be used if an electrode fails, and techniques have been identified to minimize air oxidation, thereby extending electrode life. A statistical analysis was employed during the LSOAT to identify graphite collars and an insulative surface as successful cold cap subsidence techniques. The LSOAT also showed that even under worst-case conditions, the off-gas system exceeds the flow requirements necessary to maintain a negative pressure on the hood covering the area being vitrified. The retention of simulated radionuclides and chemicals in the soil and off-gas system exceeds requirements so that projected emissions are one to two orders of magnitude below the maximum permissible concentrations of contaminants at the stack

  15. 49 CFR 232.505 - Pre-revenue service acceptance testing plan.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Pre-revenue service acceptance testing plan. 232... § 232.505 Pre-revenue service acceptance testing plan. (a) General; submission of plan. Except as... its system the operating railroad or railroads shall submit a pre-revenue service acceptance...

  16. 7 CFR 1755.400 - RUS standard for acceptance tests and measurements of telecommunications plant.

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false RUS standard for acceptance tests and measurements of telecommunications plant. 1755.400 Section 1755.400 Agriculture Regulations of the Department of Agriculture..., ACCEPTABLE MATERIALS, AND STANDARD CONTRACT FORMS § 1755.400 RUS standard for acceptance tests...

  17. Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer

    This document comprises the Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer. This document presents the results of Acceptance Testing of the 241-AZ-101 Ultrasonic Interface Level Analyzers (URSILLAs). Testing of the URSILLAs was performed in accordance with ATP-260-001, ''URSILLA Pre-installation Acceptance Test Procedure''. The objective of the testing was to verify that all equipment and components function in accordance with design specifications and original equipment manufacturer's specifications

  18. Acceptance test report, 241-SY-101 Flexible Receiver System, Phase 2 testing

    This document summarizes the results of the Phase 2 acceptance test of the 241-SY-101 Flexible Receiver System (FRS). The FRS is one of six major components of the Equipment Removal System, which has been designed to retrieve, transport, and store the test mixer pump currently installed in Tank 241-SY-101. The purpose of this acceptance test is to verify the strength of the containment bag and bag bottom cinching mechanism. It is postulated that 68 gallons of waste could be trapped inside the pump internals. The bag must be capable of supporting this waste if it shakes loose and drains to the bottom of the bag after the bag bottom has been cinched closed. This acceptance test was performed at the Maintenance and Storage Facility (MASF) Facility in the 400 area on January 23, 1995. The bag assembly supported the weight of 920 kg (2,020 lbs) of water with no leakage or damage to the bag. This value meets the acceptance criteria of 910 kg of water and therefore the results were found to be acceptable. The maximum volume of liquid expected to be held up in the pump internals is 258 L (68 gallons), which corresponds to 410 kg. This test weight gives just over a safety factor of 2. The bag also supported a small shock load while it was filled with water when the crane hoisted the bag assembly up and down. Based on the strength rating of the bag components, the bag assembly should support 2--3 times the test weight of 910 kg

  19. Acceptance Test Report for the 241-AN-107 Enraf Advanced Technology Gauges

    This Acceptance Test Report covers the results of the execution of the Acceptance Test Procedure for the 241-AN-107 Enraf Advanced Technology Gauges. The test verified the proper operation of the gauges to measure waste density and level in the 241-AN-107 tank

  20. Acceptance Test Report for the 241-AN-107 Enraf Advanced Technology Gauges

    Dowell, J.L.; Enderlin, V.R.

    1995-06-01

    This Acceptance Test Report covers the results of the execution of the Acceptance Test Procedure for the 241-AN-107 Enraf Advanced Technology Gauges. The test verified the proper operation of the gauges to measure waste density and level in the 241-AN-107 tank.

  1. PDSS/IMC qualification test software acceptance procedures

    1984-01-01

    Tests to be performed for qualifying the payload development support system image motion compensator (IMC) are identified. The performance of these tests will verify the IMC interfaces and thereby verify the qualification test software.

  2. Eddy current testing on structures of nuclear-grade PGX graphite for acceptance test in HTTR

    Acceptance test with eddy current testing is planned to be applied to the core support graphite structures made of PGX graphite, nuclear-grade near-isotropic graphite, in the HTTR. The eddy current testing widely applied to metallic components is not applicable to porous graphite materials due to different characteristics compared with metallic ones. Hence, the eddy current testing method for the fine-grained, nuclear-grade IG-110 graphite had been established. However, this method is also not applicable to the PGX graphite owing to the different flaw detectability because the PGX consists of larger grains and pores than the IG-110. Therefore the eddy current testing method and condition for the PGX graphite were established on the bases of the experimental investigation. (author)

  3. Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

    This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver devices. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

  4. Project W-151 flexible receiver radiation detector system acceptance test plan. Revision 1

    The attached document is the Acceptance Test Plan for the portion of Project W-151 dealing with acceptance of gamma-ray detectors and associated electronics manufactured at the Idaho National Engineering Laboratory (INEL). The document provides a written basis for testing the detector system, which will take place in the 305 building (300 Area)

  5. 49 CFR 238.111 - Pre-revenue service acceptance testing plan.

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Pre-revenue service acceptance testing plan. 238... and General Requirements § 238.111 Pre-revenue service acceptance testing plan. (a) Passenger equipment that has previously been used in revenue service in the United States. For passenger...

  6. Determining the acceptance of the Brookhaven EBIS Test Stand for primary ions by computer simulation

    We report on computer studies to determine the acceptance of the Electron Beam Ion Source Test Stand (EBTS) at BNL. Knowledge of the acceptance is a useful guide in selecting a source of primary ions, and in designing a transfer line which best matches the primary ion beam to the acceptance of the EBTS. In this work, an ion beam with suitable parameters is tracked out of the EBIS, to a plane where knowledge of the acceptance is wanted. The emittance of the extracted beam in this plane gives a starting point for determining a more reliable value of acceptance. The result will be compared with a theoretical estimate

  7. Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

    The purpose of this document is to describe tests performed to validate Revision 12.0 of the TMACS Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be communicating to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

  8. Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

    BARNES, D.A.

    2000-06-01

    The purpose of this document is to describe tests performed to validate Revision 12.0 of the TMACS Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be communicating to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab.

  9. Project B610 process control configuration acceptance test report

    The purpose of this test is to verify the Westinghouse configuration of the MICON A/S Distributed Control System for project B610. The following will be verified: (1) proper assignment and operation of all field inputs to and outputs from the MICON Termination panels; (2) proper operation of all display data on the operators' console; (3) proper operation of all required alarms; and (4) proper operation of all required interlocks. This test only verifies the proper operation of the Westinghouse control configuration (or program). It will not be responsible for verifying proper operation of the MICON hardware or operating software. Neither does it test any of the B610 instrument. The MICON hardware and software has been tested as part of the equipment procurement. Instrumentation and wiring installed under project B620 will be tested under a separate functional test. In some cases, precise transmitter ranges, alarm setpoints, and controller tuning parameters are not available at this time. Therefore, approximate values are used during the test. This should not affect the proper operation of the configuration or the validity of this test. Final values will be assigned during operability testing

  10. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid W

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''W''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  11. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid L

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''L''. The ATP will be performed after the construction of the PIC skid in the shop

  12. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  13. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  14. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''U''

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''U''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  15. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid T

    This Acceptance Test Procedure (ATP) provides for the inspection and testing Of the new Pumping Instrumentation and Control (PIC) skid designed as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  16. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid R

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''R''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  17. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''Q''

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  18. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''T''

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  19. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid N

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''N''. The ATP will be performed after the construction of the PIC skid in the shop

  20. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid V

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control. (PIC) skid designed as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop

  1. Acceptance test report for the 241-SY-101 Flexible Receiver Gamma Detector System

    This Acceptance Test Report is for the 241-SY-101 Flexible Receiver Gamma Detector System. This test verified that the data logger and data converter for the gamma detector system functions as intended

  2. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid sup L sup

    Koch, M R

    1999-01-01

    This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''L''. The ATP will be performed after the construction of the PIC skid in the shop.

  3. Test and acceptance from the AE point of view

    The power industry has undergone the transition from utilizing construction engineers for startup activities to utilizing test engineers who are responsible for the preparation or execution of a formal test program. This has come about because testing has been given sufficient importance to justify those participating within the industry to establish it as a specialty phase apart from engineering/design and construction. Presently testing is being conducted by those organizations that have either engineered and/or constructed the unit which may be a position of conflict in regards to unbiased test. The tester (third party) concept promotes the repetition, independence, and expertise of a test organization responsible to the utility for certifying that each system has been tested to the design criteria established by others. A move to this concept should result in better generating stations with higher availability because it has been completely tested by an organization with this sole contractual responsibility. The AE, NSSS, and utility would all benefit with possibly no additional costs incurred

  4. Waste retrieval sluicing system data acquisition system acceptance test report

    This document describes the test procedure for the Project W-320 Tank C-106 Sluicing Data Acquisition System (W-320 DAS). The Software Test portion will test items identified in the WRSS DAS System Description (SD), HNF-2115. Traceability to HNF-2115 will be via a reference that follows in parenthesis, after the test section title. The Field Test portion will test sensor operability, analog to digital conversion, and alarm setpoints for field instrumentation. The W-320 DAS supplies data to assist thermal modeling of tanks 241-C-106 and 241-AY-102. It is designed to be a central repository for information from sources that would otherwise have to be read, recorded, and integrated manually. Thus, completion of the DAS requires communication with several different data collection devices and output to a usable PC data formats. This test procedure will demonstrate that the DAS functions as required by the project requirements stated in Section 3 of the W-320 DAS System Description, HNF-2115

  5. Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

    The purpose of this document is to describe tests performed to validate Revision 11.2 of the TMACS Monitor and Control System (TMCACS) and verify that the software functions as intended by design. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

  6. CSI computer system/remote interface unit acceptance test results

    Sparks, Dean W., Jr.

    1992-01-01

    The validation tests conducted on the Control/Structures Interaction (CSI) Computer System (CCS)/Remote Interface Unit (RIU) is discussed. The CCS/RIU consists of a commercially available, Langley Research Center (LaRC) programmed, space flight qualified computer and a flight data acquisition and filtering computer, developed at LaRC. The tests were performed in the Space Structures Research Laboratory (SSRL) and included open loop excitation, closed loop control, safing, RIU digital filtering, and RIU stand alone testing with the CSI Evolutionary Model (CEM) Phase-0 testbed. The test results indicated that the CCS/RIU system is comparable to ground based systems in performing real-time control-structure experiments.

  7. Acceptance Test Procedure: SY101 air pallet system

    The purpose of this test procedure is to verify that the system(s) procured to load the SY-101 Mitigation Test Pump package fulfills its functional requirements. It will also help determine the man dose expected due to handling of the package during the actual event. The scope of this procedure focuses on the ability of the air pallets and container saddles to carry the container package from the new 100 foot concrete pad into 2403-WD where it will be stored awaiting final disposition. This test attempts to simulate the actual event of depositing the SY-101 hydrogen mitigation test pump into the 2403-WD building. However, at the time of testing road modifications required to drive the 100 ton trailer into CWC were not performed. Therefore a flatbed trailer will be use to transport the container to CWC. The time required to off load the container from the 100 ton trailer will be recorded for man dose evaluation on location. The cranes used for this test will also be different than the actual event. This is not considered to be an issue due to minimal effects on man dose

  8. The Northern Regional Programme for the acceptance testing of X-ray equipment

    Since 1984 the Regional Medical Physics Department has participated in a regional acceptance testing programme for all X-ray equipment from mobile units to computed tomography scanners. The organizational and radiation physics aspects of the programme are described. Three levels of tests are performed by physicists: the first on installation, the second after 3 months, and the final visit just prior to the end of the manufacturer's warranty. The second test is only performed if any aspect of performance requires rechecking as a result of the first visit. Acceptance test protocols are based on those published by the Institute of Physical Sciences in Medicine. Details of the limiting values for the acceptance test measurements are given. The results of the programme are discussed. In some instances the testing has resulted in modifications to the design and construction of X-ray equipment. Acceptance testing is important in determining a baseline standard of performance against which routine quality assurance may be assessed. (author)

  9. Acceptance tests of the BEPC II RF transmitter and the circulator

    The high power RF transmitter and the circulator with 500 MHz/250 kW which will be operated in Beijing Electron-Positron Collider Upgrade (BEPC II) project have been installed on site, and adjustments and acceptance test have been finished, which is the first transmitter system of 500 MHz/250 kW in China. In this paper, the test principle and all measurements as well as commissioning result in the acceptance test are introduced in details, and the actual machine technical parameters and performance are presented. An acceptance test conclusion by comparing with the design requirements is given. (authors)

  10. Acceptance tests of cryogenic components for SST-1

    The cryogenics system is one of the critical sub-systems in SST-1. The role of cryogenics systems is to facilitate the smooth cool-down, warm up and steady state operation as well as to take care about any abnormal events in safe mode during the operation. As a part of SST-1 machine shell, the cryogenics division is responsible for cold helium (at 4.5 K) and liquid nitrogen (at 77 K) hydraulics. This hydraulic network consists of headers, 80 K embossed shields, interconnecting loops, ceramic feed through at the vacuum barrier, flexible hoses and electrical breaks for cold helium as well as liquid nitrogen circuits. Before installation of individual components in SST-1, the performance validation tests were mandatory as part of mandatory stringent protocols fulfillment. The performance validation tests were conducted from individual components to integrated assembly level. In this paper, we report the essence of procedures followed and the performance test results. (author)

  11. WRAP low level waste restricted waste management (LLW RWM) glovebox acceptance test report

    Leist, K.J.

    1997-11-24

    On April 22, 1997, the Low Level Waste Restricted Waste Management (LLW RWM) glovebox was tested using acceptance test procedure 13027A-87. Mr. Robert L. Warmenhoven served as test director, Mr. Kendrick Leist acted as test operator and test witness, and Michael Lane provided miscellaneous software support. The primary focus of the glovebox acceptance test was to examine glovebox control system interlocks, operator Interface Unit (OIU) menus, alarms, and messages. Basic drum port and lift table control sequences were demonstrated. OIU menus, messages, and alarm sequences were examined, with few exceptions noted. Barcode testing was bypassed, due to the lack of installed equipment as well as the switch from basic reliance on fixed bar code readers to the enhanced use of portable bar code readers. Bar code testing was completed during performance of the LLW RWM OTP. Mechanical and control deficiencies were documented as Test Exceptions during performance of this Acceptance Test. These items are attached as Appendix A to this report.

  12. WRAP low level waste restricted waste management (LLW RWM) glovebox acceptance test report

    On April 22, 1997, the Low Level Waste Restricted Waste Management (LLW RWM) glovebox was tested using acceptance test procedure 13027A-87. Mr. Robert L. Warmenhoven served as test director, Mr. Kendrick Leist acted as test operator and test witness, and Michael Lane provided miscellaneous software support. The primary focus of the glovebox acceptance test was to examine glovebox control system interlocks, operator Interface Unit (OIU) menus, alarms, and messages. Basic drum port and lift table control sequences were demonstrated. OIU menus, messages, and alarm sequences were examined, with few exceptions noted. Barcode testing was bypassed, due to the lack of installed equipment as well as the switch from basic reliance on fixed bar code readers to the enhanced use of portable bar code readers. Bar code testing was completed during performance of the LLW RWM OTP. Mechanical and control deficiencies were documented as Test Exceptions during performance of this Acceptance Test. These items are attached as Appendix A to this report

  13. MAC mini acceptance test procedures, software Version 3.3

    The K Basins Materials Accounting (MAC) programs had some improvements made to it to to change slightly the access authorized users had to the modification of critical data. This ATP describes how the code was to be tested to verify its correctness

  14. Probabilistic Requirements (Partial) Verification Methods Best Practices Improvement. Variables Acceptance Sampling Calculators: Empirical Testing. Volume 2

    Johnson, Kenneth L.; White, K. Preston, Jr.

    2012-01-01

    The NASA Engineering and Safety Center was requested to improve on the Best Practices document produced for the NESC assessment, Verification of Probabilistic Requirements for the Constellation Program, by giving a recommended procedure for using acceptance sampling by variables techniques as an alternative to the potentially resource-intensive acceptance sampling by attributes method given in the document. In this paper, the results of empirical tests intended to assess the accuracy of acceptance sampling plan calculators implemented for six variable distributions are presented.

  15. Solar panel acceptance testing using a pulsed solar simulator

    Hershey, T. L.

    1977-01-01

    Utilizing specific parameters as area of an individual cell, number in series and parallel, and established coefficient of current and voltage temperature dependence, a solar array irradiated with one solar constant at AMO and at ambient temperature can be characterized by a current-voltage curve for different intensities, temperatures, and even different configurations. Calibration techniques include: uniformity in area, depth and time, absolute and transfer irradiance standards, dynamic and functional check out procedures. Typical data are given for individual cell (2x2 cm) to complete flat solar array (5x5 feet) with 2660 cells and on cylindrical test items with up to 10,000 cells. The time and energy saving of such testing techniques are emphasized.

  16. Acceptance test report for the Tank 241-C-106 in-tank imaging system

    This document presents the results of Acceptance Testing of the 241-C-106 in-tank video camera imaging system. The purpose of this imaging system is to monitor the Project W-320 sluicing of Tank 241-C-106. The objective of acceptance testing of the 241-C-106 video camera system was to verify that all equipment and components function in accordance with procurement specification requirements and original equipment manufacturer's (OEM) specifications. This document reports the results of the testing

  17. Test report for run-in acceptance testing of hydrogen mitigation test pump-2

    This document provides the results of the run-in test of the replacement mixer pump for the Tank 241-SY-101. The test was conducted at the 400 Area MASF facility between August 12 and September 29, 1994. The report includes findings, analysis, recommendations, and corrective actions taken

  18. MBA acceptance test procedures, software Version 1.4

    The Mass Balance Program (MBA) is an adjunct to the Materials Accounting database system, Version 3.4. MBA was written to equip the personnel performing K-Basin encapsulation tasks with a conservative estimate of accumulated sludge during the processing of canisters into and out of the chute. The K Basins Materials Balance programs had some minor improvements made to it to feedback the chute processing status to the operator better. This ATP describes how the code was to be tested to verify its correctness

  19. 242-A MCS Logic Acceptance Test Report for Year 2000 Upgrade

    242-A Evaporator distributive control system upgrade to D/3 version 9.0-2 for year 2000 compliance. Testing was performed per test procedure HNF-3568. There were no unresolved exceptions. The system responded correctly to all testing and meets the requirements to operate the 242-A This report documents the acceptance test results for the Evaporator facility

  20. Acceptance of Genetic Testing in a General Population: Age, Education and Gender Differences.

    Aro, A. R.; Hakonen, A.; Hietala, M.; Lonnqvist, J.; Niemela, P.; Peltonen, L; Aula, P.

    1997-01-01

    Effects of age, education, and gender on acceptance of genetic testing were studied. Finnish participants responded to a questionnaire presenting reasons for and against genetic testing (N=1,967). Intentions to take genetic tests, worries, and experience of genetic test or hereditary disease were also assessed. Results are presented and discussed.…

  1. Acceptance Test Report for the high pressure water jet system canister cleaning fixture

    This Acceptance Test confirmed the test results and recommendations, documented in WHC-SD-SNF-DTR-001, Rev. 0 Development Test Report for the High Pressure Water Jet System Nozzles, for decontaminating empty fuel canisters in KE-Basin. Optimum water pressure, water flow rate, nozzle size and overall configuration were tested

  2. Affect and technology acceptance: A test of two mechanisms

    Scholderer, Joachim; Grunert, Klaus G.; Søndergaard, Helle Alsted

    Commercialization of new technologies may be hampered by stakeholder resistance and a sceptical public. Genetic modification (GM) has suffered particularly from such problems. At present, for example, practically no products exist on the shelves of European retailers that are labelled as containing...... resistant to all forms of communicative interventions. A study is presented in which the effectiveness and mechanisms of direct-experience interventions are experimentally tested. Results indicate that the positive affect evoked by a single trial of a high-quality genetically modified food can lead to...... practice, focusing on point-of-sale promotions that could be the key element in the launch of the first genetically modified foods in markets that are as yet GM-free....

  3. Project B610 process control configuration acceptance test procedure

    The purpose of this test is to verify the Westinghouse configuration of the MICON A/S Distributed Control System for project B610. The following will be verified: proper assignment and operation of all field inputs to and outputs from the MICON Termination panels; proper operation of all display data on the operator's console; proper operation of all required alarms; and proper operation of all required interlocks. The MICON A/S control system is configured to replace all the control, indication, and alarm panels now located in the Power Control Room. Nine systems are covered by this control configuration, 2736-ZB HVAC, 234-5Z HVAC, Process Vacuum, Dry Air, 291-Z Closed Loop Cooling, Building Accelerometer, Evacuation Siren, Stack CAMs, and Fire. The 2736-ZB HVAC system consists of the ventilation controls for 2736-ZB and 2736-Z as well as alarms for the emergency generators and 232-Z. The 234-5Z HVAC system is the ventilation controls for 235-5Z and 236-Z buildings. Process Vacuum covers the controls for the 26 inch vacuum system. Dry Air covers the controls for the steam and electric air dryers. The 291-Z Closed Loop Cooling system consists of the status indications and alarms for the 291-Z compressor and vacuum pump closed loop cooling system. The rest of closed loop cooling was tested earlier. The Building Accelerometer system consists of the status indications for the two seismic system accelerometers. The Evacuation Siren system includes the controls for the evacuation and take cover sirens. Stack CAMs cover the alarms for the various building ventilation stack continuous air monitors. Finally, the Fire system covers the various fire alarms now located in Room 321-A

  4. Acceptance/Operational Test Report for Tank 241-AN-104 camera and camera purge control system

    This Acceptance/Operational Test Procedure (ATP/OTP) will document the satisfactory operation of the camera purge panel, purge control panel, color camera system and associated control components destined for installation. The final acceptance of the complete system will be performed in the field. The purge panel and purge control panel will be tested for its safety interlock which shuts down the camera and pan-and-tilt inside the tank vapor space during loss of purge pressure and that the correct purge volume exchanges are performed as required by NFPA 496. This procedure is separated into seven sections. This Acceptance/Operational Test Report documents the successful acceptance and operability testing of the 241-AN-104 camera system and camera purge control system

  5. Delinquency and Peer Acceptance in Adolescence: A Within-Person Test of Moffitt’s Hypotheses

    Rulison, Kelly L.; Kreager, Derek A.; Osgood, D. Wayne

    2014-01-01

    We tested two hypotheses derived from Moffitt’s (1993) taxonomic theory of antisocial behavior, both of which are central to her explanation for the rise in delinquency during adolescence. Specifically, we tested whether persistently delinquent individuals become more accepted by their peers during adolescence and whether individuals who abstain from delinquent behavior become less accepted. Participants were 4,359 adolescents from 14 communities in the PROSPER study, which assessed friendshi...

  6. Test Report for Acceptance Test Procedure for Pumping and Instrumentation Control Skid ''K''

    JOHNS, B.R.

    1999-10-28

    This is a Test Report for Acceptance Test Procedure (ATP) HNF-4276. This test report provides the results of the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''K''. The ATP was successfully completed. A copy of the completed ATP is in the Appendix of this document.

  7. Test report for the run-in acceptance testing of the hydrogen mitigation retrieval Pump-3

    This report will provide the findings of the demonstration test conducted on the Double-Shell Tank (DST) 241-SY-101 HMR Pump-3 in accordance with WHC-SDWM-TP-434 ''Test plan for run-in acceptance testing of hydrogen mitigation/retrieval pump-3'' at the 400 Area Maintenance and Storage Facility (MASF) building from 7 June 1996 through 30 July 1996 per work package 4A-96-92/W. The DST 241-SY-101 hydrogen mitigation retrieval Pump-3 is a 200-HP submersible electric driven pump that has been modified for use in the DST 241-SY-101 containing mixed waste located in the 200W area. The pump has a motor driven rotation mechanism that allows the pump column to rotate through 355 degree. Prior to operation, pre-operational checks were performed which included loop calibration grooming and alignment of instruments, learning how plumb HMR-3 assembly hung in a vertical position and bump test of the motor to determine rotation direction. The pump was tested in the MASF Large Diameter Cleaning Vessel (LDCV) with process water at controlled temperatures and levels. In addition, the water temperature of the cooling water to the motor oil heat exchanger was recorded during testing. A 480-volt source powered a Variable Frequency Drive (VFD). The VFD powered the pump at various frequencies and voltages to control speed and power output of the pump. A second VFD powered the oil cooling pump. A third VFD was not available to operate the rotational drive motor during the 72 hour test, so it was demonstrated as operational before and after the test. A Mini Acquisition and Control System (Mini-DACS) controls pump functions and monitoring of the pump parameters. The Mini-DACS consists of three computers, software and some Programmable Logic Controllers (PLC). Startup and shutdown of either the pump motor or the oil cooling pump can be accomplished by the Mini-DACS. When the pump was in operation, the Mini-DACS monitors automatically collects data electronically. However, some required data

  8. Acceptance testing protocol for magnetic resonance imaging systems; Protocolo de testes de aceitacao em equipamentos de imagem por ressonancia magnetica

    Mazzola, Alessandro Andre [Universidade Federal, Rio de Janeiro, RJ (Brazil). Faculdade de Medicina. Programa de Pos-graduacao em Radiologia]. E-mail: aam.ez@terra.com.br; Herdade, Silvio Bruni [Sao Paulo Univ., SP (Brazil). Inst. de Fisica; Koch, Hilton Augusto; Carvalho, Antonio Carlos Pires [Universidade Federal, Rio de Janeiro, RJ (Brazil). Faculdade de Medicina. Dept. de Radiologia

    2005-05-15

    Objective: to develop an acceptance testing protocol for magnetic resonance imaging systems and to show which and how phantoms could be used to collect data. Materials and methods: the definition, procedure, analysis and the acceptation criteria were created for each of 15 selected tests. Results: These tests allow the evaluation of technical specifications stated on the manufacturer's sales proposal and to establish reference values to be used in subsequent constancy tests. Conclusion: future quality assurance programs in magnetic resonance imaging should consider employing tests similar or equal to the ones described in this paper. (author)

  9. Building Energy Simulation Test for Existing Homes (BESTEST-EX): Instructions for Implementing the Test Procedure, Calibration Test Reference Results, and Example Acceptance-Range Criteria

    Judkoff, R.; Polly, B.; Bianchi, M.; Neymark, J.; Kennedy, M.

    2011-08-01

    This publication summarizes building energy simulation test for existing homes (BESTEST-EX): instructions for implementing the test procedure, calibration tests reference results, and example acceptance-range criteria.

  10. Community acceptability of use of rapid diagnostic tests for malaria by community health workers in Uganda

    Waiswa Peter; Pariyo George W; Kiguli Juliet; Tibenderana James K; Mukanga David; Bajunirwe Francis; Mutamba Brian; Counihan Helen; Ojiambo Godfrey; Kallander Karin

    2010-01-01

    Abstract Background Many malarious countries plan to introduce artemisinin combination therapy (ACT) at community level using community health workers (CHWs) for treatment of uncomplicated malaria. Use of ACT with reliance on presumptive diagnosis may lead to excessive use, increased costs and rise of drug resistance. Use of rapid diagnostic tests (RDTs) could address these challenges but only if the communities will accept their use by CHWs. This study assessed community acceptability of the...

  11. Standard-B auto grab sampler hydrogen monitoring system, Acceptance Test Report

    Project W-369, Watch List Tank Hydrogen Monitors, installed a Standard-C Hydrogen Monitoring System (SHMS) on the Flammable gas waste tank AN-104. General Support Projects (8K510) was support by Test Engineering (7CH30) in the performance of the Acceptance Test Procedures (ATP) to qualify the SHMS cabinets on the waste tank. The ATP's performance was controlled by Tank Farm work package. This completed ATP is transmitted by EDT-601748 as an Acceptance Test Report (ATR) in accordance with WHC-6-1, EP 4.2 and EP 1.12

  12. Understanding Student Teachers’ Behavioural Intention to Use Technology: Technology Acceptance Model (TAM) Validation and Testing

    Kung-Teck, Wong; Rosma bt Osman; Pauline Swee Choo, Goh; Mohd Khairezan Rahmat

    2013-01-01

    This study sets out to validate and test the Technology Acceptance Model (TAM) in the context of Malaysian student teachers’ integration of their technology in teaching and learning. To establish factorial validity, data collected from 302 respondents were tested against the TAM using confirmatory factor analysis (CFA), and structural equation modelling (SEM) was used for model comparison and hypotheses testing. The goodness-of-fit test of the analysis shows partial support of the applicabili...

  13. Delinquency and peer acceptance in adolescence: a within-person test of Moffitt's hypotheses.

    Rulison, Kelly L; Kreager, Derek A; Osgood, D Wayne

    2014-11-01

    We tested 2 hypotheses derived from Moffitt's (1993) taxonomic theory of antisocial behavior, both of which are central to her explanation for the rise in delinquency during adolescence. We tested whether persistently delinquent individuals become more accepted by their peers during adolescence and whether individuals who abstain from delinquent behavior become less accepted. Participants were 4,359 adolescents from 14 communities in the PROSPER study, which assessed friendship networks and delinquency from 6th (M = 11.8 years) to 9th (M = 15.3 years) grade. We operationalized peer acceptance as number of nominations received (indegree centrality), attractiveness as a friend (adjusted indegree centrality), and network bridging potential (betweenness centrality) and tested the hypotheses with multilevel modeling. Contrary to Moffitt's hypothesis, persistently delinquent youths did not become more accepted between early and middle adolescence, and although abstainers were less accepted in early adolescence, they became more accepted over time. Results were similar for boys and girls; when differences occurred, they provided no support for Moffitt's hypotheses for boys and were opposite of her hypotheses for girls. Sensitivity analyses in which alternative strategies and additional data were used to identify persistently delinquent adolescents produced similar results. We explore the implications of these results for Moffitt's assertions that social mimicry of persistently antisocial adolescents leads to increases in delinquency and that social isolation leads to abstention. (PsycINFO Database Record (c) 2014 APA, all rights reserved). PMID:25243328

  14. Delinquency and Peer Acceptance in Adolescence: A Within-Person Test of Moffitt’s Hypotheses

    Rulison, Kelly L; Kreager, Derek A.; Osgood, D. Wayne

    2015-01-01

    We tested two hypotheses derived from Moffitt’s (1993) taxonomic theory of antisocial behavior, both of which are central to her explanation for the rise in delinquency during adolescence. Specifically, we tested whether persistently delinquent individuals become more accepted by their peers during adolescence and whether individuals who abstain from delinquent behavior become less accepted. Participants were 4,359 adolescents from 14 communities in the PROSPER study, which assessed friendship networks and delinquency from 6th (M = 11.8 years) to 9th (M = 15.3 years) grade. We operationalized peer acceptance as: number of nominations received (indegree centrality), attractiveness as a friend (adjusted indegree centrality), and network bridging potential (betweenness centrality) and tested the hypotheses using multilevel modeling. Contrary to Moffitt’s hypothesis, persistently delinquent youth did not become more accepted between early and middle adolescence, and although abstainers were less accepted in early adolescence, they became more accepted over time. Results were similar for boys and girls; when differences occurred, they provided no support for Moffitt’s hypotheses for boys and were opposite of her hypotheses for girls. Sensitivity analyses using alternative strategies and additional data to identify persistently delinquent adolescents produced similar results. We explore the implications of these results for Moffitt’s assertions that social mimicry of persistently antisocial adolescents leads to increases in delinquency and that social isolation leads to abstention. PMID:25243328

  15. Enraf series 854 Advanced Technology Gauge (ATG) acceptance test procedure. Revision 3

    This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer's instructions and specifications and is properly setup prior to being delivered to the tank farm area

  16. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''V''

    This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping Instrumentation and Control (PIC) skid ''V''. The scope section lists the systems and functions to be checked. This ATP will be performed at the Site Fabrication Services (SFS) shop upon completion of the construction of the PIC skid

  17. Acceptance Test Procedure for New Pumping and Instrumentation Control Skid M

    This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping and Instrumentation Control (PIC) skid ''M''. The Scope section lists the systems and functions to be checked. This ATP will be performed at the Site Fabrication Service's (SFS) shop upon completion of construction of the PIC skid

  18. Project W-320 acceptance test report for AY-farm electrical distribution

    This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the AY-Farm Electrical Distribution System functions as required by the design criteria. This test is divided into three parts to support the planned construction schedule; Section 8 tests Mini-Power Pane AY102-PPI and the EES; Section 9 tests the SSS support systems; Section 10 tests the SSS and the Multi-Pak Group Control Panel. This test does not include the operation of end-use components (loads) supplied from the distribution system. Tests of the end-use components (loads) will be performed by other W-320 ATPs

  19. High acceptance of an early dyslexia screening test involving genetic analyses in Germany.

    Wilcke, Arndt; Müller, Bent; Schaadt, Gesa; Kirsten, Holger; Boltze, Johannes

    2016-02-01

    Dyslexia is a developmental disorder characterized by severe problems in the acquisition of reading and writing skills. It has a strong neurobiological basis. Genetic influence is estimated at 50-70%. One of the central problems with dyslexia is its late diagnosis, normally not before the end of the 2nd grade, resulting in the loss of several years for early therapy. Currently, research is focusing on the development of early tests for dyslexia, which may be based on EEG and genetics. Our aim was to determine the acceptance of such a future test among parents. We conducted a representative survey in Germany with 1000 parents of children aged 3-7 years, with and without experience of dyslexia. 88.7% of the parents supported the introduction of an early test for dyslexia based on EEG and genetics; 82.8% would have their own children tested, and 57.9% were willing to pay for the test if health insurance did not cover the costs. Test acceptance was significantly higher if parents had prior experience with dyslexia. The perceived benefits of such a test were early recognition and remediation and, preventing deficits. Concerns regarded the precision of the test, its potentially stigmatizing effect and its costs. The high overall support for the test leads to the conclusion that parents would accept a test for dyslexia based on EEG and genetics. PMID:26036858

  20. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  1. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    NSTec Environmental Management

    2009-05-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  2. W-026 acceptance test report plant control system hardware (submittal {number_sign} 220.C)

    Watson, T.L., Fluor Daniel Hanford

    1997-02-14

    Acceptance Testing of the WRAP1 Plant Control System Hardware was conducted throughout the construction of WRAPI with the final testing on the Process Area hardware being completed in November 1996. The hardware tests were broken out by the following functional areas; Local Control Units, Operator Control Stations in the WRAP Control Room, DMS Server, PCS Server, Operator Interface Units, printers, DMS terminals, WRAP Local Area Network/Communications, and bar code equipment. This document contains a completed copy of each of the hardware tests along with the applicable test logs and completed test exception reports.

  3. W-026 acceptance test plan plant control system hardware (submittal {number_sign} 216)

    Watson, T.L., Fluor Daniel Hanford

    1997-02-14

    Acceptance Testing of the WRAP 1 Plant Control System Hardware will be conducted throughout the construction of WRAP I with the final testing on the Process Area hardware being completed in November 1996. The hardware tests will be broken out by the following functional areas; Local Control Units, Operator Control Stations in the WRAP Control Room, DMS Server, PCS Server, Operator Interface Units, printers, DNS terminals, WRAP Local Area Network/Communications, and bar code equipment. This document will contain completed copies of each of the hardware tests along with the applicable test logs and completed test exception reports.

  4. KE basin recirculation/skimmer/IX systems restart acceptance test report

    The 105 KE Basin Recirculation System and Skimmer Loop have been upgraded to provide the flexibility to run the Ion Exchange Modules on either system to support spent fuel removal for the Spent Nuclear Fuel Project. This Acceptance Test Report Provides the documentation of the leak Testing for the construction work associated with the IXM inlet and outlet piping, places the cartridge filters back in service and provides the functional testing of the IXM's on the recirculation and skimmer systems

  5. 105 K east ion exchange and cartridge filter restart instrumentation acceptance test report

    Acceptance Test Report following the completion of ATP-012 for the 105KE CP-A and CP-A Computer and PLC Panels. The test was conducted from 11/13/95 to 12/11/95. Three test discrepancies were generated during the ATP and all were dispositioned and closed. All sections were completed except Section 5.9 which was deleted per ECN 190556

  6. MAC Version 3.3, MBA Version 1.3 acceptance test summary report

    The K Basins Materials Accounting (MAC) and Materials Balance (MBA) programs had the Paradox Code Cleanup ATP run to check out the systems. This report describes the results of the test and provides the signoff sheets associated with the testing. The Acceptance Test results indicate that the MAC and MBA systems are ready for operation using the cleaned up code. The final codes were removed to the production space on the customer server on April 15th

  7. Utility-Scale Power Tower Solar Systems: Performance Acceptance Test Guidelines

    Kearney, D.

    2013-03-01

    The purpose of these Guidelines is to provide direction for conducting performance acceptance testing for large power tower solar systems that can yield results of a high level of accuracy consistent with good engineering knowledge and practice. The recommendations have been developed under a National Renewable Energy Laboratory (NREL) subcontract and reviewed by stakeholders representing concerned organizations and interests throughout the concentrating solar power (CSP) community. An earlier NREL report provided similar guidelines for parabolic trough systems. These Guidelines recommend certain methods, instrumentation, equipment operating requirements, and calculation methods. When tests are run in accordance with these Guidelines, we expect that the test results will yield a valid indication of the actual performance of the tested equipment. But these are only recommendations--to be carefully considered by the contractual parties involved in the Acceptance Tests--and we expect that modifications may be required to fit the particular characteristics of a specific project.

  8. Accepting test-anxiety-related thoughts increases academic performance among undergraduate students

    Senay Ibrahim

    2012-01-01

    Full Text Available Given that unwanted thoughts are enhanced when suppressed, we tested among college freshmen who were about to take an academic exam if an acceptance strategy consisting of not suppressing intrusive thoughts will improve test performance. This strategy proved superior to students’ own default strategies as much as a modified, alternative strategy, avoiding the antecedents of intrusive thoughts. Moreover, the combination of the two strategies counteracted a stronger, negative effect of test anxiety on test performance as compared with each strategy used alone. The results suggest that not only intrusive thoughts per se but also the suppression of these thoughts can disrupt test performance, and hint that approaching such thoughts with acceptance may not interfere with simultaneously working toward avoiding the antecedents of these thoughts.

  9. Acceptance test procedure for a portable, self-contained nitrogen supply

    This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0249 Rev. 1 and ECN 606112. The equipment being tested is a Portable, Self-Contained Nitrogen Supply. The unit was purchased as a Design and Fabrication procurement activity. The Functional Test was written by the Seller and is contained in Appendix A. The Functional test will be performed by the Seller with representatives of the Westinghouse Hanford Company performing inspection and witnessing the functional test at the Seller's location

  10. 14 CFR 91.1071 - Crewmember: Tests and checks, grace provisions, training to accepted standards.

    2010-01-01

    ... performance to the person conducting the check, the program manager may not use the pilot, nor may the pilot... OPERATING AND FLIGHT RULES Fractional Ownership Operations Program Management § 91.1071 Crewmember: Tests... provisions, training to accepted standards. 91.1071 Section 91.1071 Aeronautics and Space FEDERAL...

  11. Integrating Telemedicine for Disaster Response: Testing the Emergency Telemedicine Technology Acceptance Model

    Davis, Theresa M.

    2013-01-01

    Background: There is little evidence that technology acceptance is well understood in healthcare. The hospital environment is complex and dynamic creating a challenge when new technology is introduced because it impacts current processes and workflows which can significantly affect patient care delivery and outcomes. This study tested the effect…

  12. Acceptance Test Report for the Modular Automation System (MAS) Manufactured by Honeywell Inc

    This document details the performance of the acceptance test of the Honeywell MAS Control System for equipment to be installed in gloveboxes HA-20MB and HA-211 at a later date. Equipment that was anticipated included 6 stabilization furnaces, only three and their associated equipment were installed

  13. A FORTRAN IV Program for Multiple-choice Tests with Predetermined Minimal Acceptable Performance Levels

    Noe, Michael J.

    1976-01-01

    A Fortran IV multiple choice test scoring program for an IBM 370 computer is described that computes minimally acceptable performance levels and compares student scores to these levels. The program accomodates up to 500 items with no more than nine alternatives from a group of examinees numbering less than 10,000. (Author)

  14. Acceptance Test Report for Fourth-Generation Hanford Corrosion Monitoring Cabinet

    This Acceptance Test Plan (ATP) will document the satisfactory operation of the third-generation corrosion monitoring cabinet (Hiline Engineering Part No.0004-CHM-072-C01). This ATP will be performed by the manufacturer of the cabinet prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion monitoring cabinet. The test will consist of a continuity test of the cabinet wiring from the end of cable to be connected to corrosion probe, through the appropriate intrinsic safety barriers and out to the 15 pin D-shell connectors to be connected to the corrosion monitoring instrument. Additional testing will be performed using a constant current and voltage source provided by the corrosion monitoring hardware manufacturer to verify proper operation of corrosion monitoring instrumentation

  15. Rein tension acceptance in young horses in a voluntary test situation

    Christensen, Janne Winther; zharkikh, T.L.; Antoine, A.;

    2011-01-01

    inexperienced horses are willing to accept in order to obtain a food reward; whether the tension acceptance changes during 3 consecutive test days; and whether rein tension correlates with the expression of conflict behaviour and heart rate. Hypotheses: Pressure-naïve horses will apply only little rein tension...... bar) to obtain a food reward in a voluntary test situation. On each test day, each horse was exposed to 2 control sessions (loose reins), an intermediate and a short rein session (1 min/session). Rein tension, heart rate and behaviour were recorded. Results: The horses applied significantly more...... tension on the first day (mean rein tension: 10.2 N), compared to the second and third test day (Day 2: 6.0 and Day 3: 5.7 N). The horses showed significantly more conflict behaviour in the short rein treatment. There was no treatment effect on heart rate. Conclusions and potential relevance: The horses...

  16. Accepting test-anxiety-related thoughts increases academic performance among undergraduate students

    Senay Ibrahim; Cetinkaya Mustafa; Usak Muhammet

    2012-01-01

    Given that unwanted thoughts are enhanced when suppressed, we tested among college freshmen who were about to take an academic exam if an acceptance strategy consisting of not suppressing intrusive thoughts will improve test performance. This strategy proved superior to students’ own default strategies as much as a modified, alternative strategy, avoiding the antecedents of intrusive thoughts. Moreover, the combination of the two strategies counteracted a stronger, negative effect of te...

  17. W-026, acceptance test report TRU empty drum compactor (submittal number-sign 634)

    On 10/19/96 and 10/21/96, the 06/04/96 version of the Empty Drum Compactor Acceptance Test Procedure was used to perform tests by INET Corporation at the Hanford WRAP facility. The INET compaction components were installed in the Diversified glovebox. The Diversified glovebox and cart and the INET compaction components, EDC HPU and drum centering device constitute the Empty Drum Compactor

  18. Acceptance test procedure for K basins dose reduction project clean and coat equipment

    This document is the Acceptance Test Procedure (ATP) for the clean and coat equipment designed by Oceaneering Hanford, Inc. under purchase order MDK-XVC-406988 for use in the 105 K East Basin. The ATP provides the guidelines and criteria to test the equipment's ability to clean and coat the concrete perimeter, divider walls, and dummy elevator pit above the existing water level. This equipment was designed and built in support of the Spent Nuclear Fuel, Dose Reduction Project. The ATP will be performed at the 305 test facility in the 300 Area at Hanford. The test results will be documented in WHC-SD-SNF-ATR-020

  19. Acceptance test procedure for K basins dose reduction project clean and coat equipment

    Creed, R.F.

    1996-03-11

    This document is the Acceptance Test Procedure (ATP) for the clean and coat equipment designed by Oceaneering Hanford, Inc. under purchase order MDK-XVC-406988 for use in the 105 K East Basin. The ATP provides the guidelines and criteria to test the equipment`s ability to clean and coat the concrete perimeter, divider walls, and dummy elevator pit above the existing water level. This equipment was designed and built in support of the Spent Nuclear Fuel, Dose Reduction Project. The ATP will be performed at the 305 test facility in the 300 Area at Hanford. The test results will be documented in WHC-SD-SNF-ATR-020.

  20. Acceptance test procedure, 241-SY-101/241-C-106 shot loading system

    This Acceptance Test Procedure is for the 241-SY-101/241-C-106 Shot Loading System. The procedure will test the components of the Shot Loading System and its capability of adequately loading shot into the annular space of the Container. The loaded shot will provide shielding as required for transporting and storage of a contaminated pump after removal from the tank. This test serves as verification that the SLS is acceptable for use in the pump removal operations for Tanks 241-SY-101, 241-C-106 and 241-AY-102. The pump removal operation for these three tanks will be performed by two different organizations with different equipment, but the Shot Loading System will be compatible between the two operations

  1. The deformable secondary mirror of VLT: final electro-mechanical and optical acceptance test results

    Briguglio, Runa; Biasi, Roberto; Xompero, Marco; Riccardi, Armando; Andrighettoni, Mario; Pescoller, Dietrich; Angerer, Gerald; Gallieni, Daniele; Vernet, Elise; Kolb, Johann; Arsenault, Robin; Madec, Pierre-Yves

    2014-07-01

    The Deformable Secondary Mirror (DSM) for the VLT ended the stand-alone electro-mechanical and optical acceptance process, entering the test phase as part of the Adaptive Optics Facility (AOF) at the ESO Headquarter (Garching). The VLT-DSM currently represents the most advanced already-built large-format deformable mirror with its 1170 voice-coil actuators and its internal metrology based on co-located capacitive sensors to control the shape of the 1.12m-diameter 2mm-thick convex shell. The present paper reports the final results of the electro-mechanical and optical characterization of the DSM executed in a collaborative effort by the DSM manufacturing companies (Microgate s.r.l. and A.D.S. International s.r.l.), INAF-Osservatorio Astrofisico di Arcetri and ESO. The electro-mechanical acceptance tests have been performed in the company premises and their main purpose was the dynamical characterization of the internal control loop response and the calibration of the system data that are needed for its optimization. The optical acceptance tests have been performed at ESO (Garching) using the ASSIST optical test facility. The main purpose of the tests are the characterization of the optical shell flattening residuals, the corresponding calibration of flattening commands, the optical calibration of the capacitive sensors and the optical calibration of the mirror influence functions.

  2. Mixed Variables-Attributes Test Plans for Single and DoubleAcceptance Sampling under Exponential Distribution

    Dongdong Xiang; Xiaolong Pu; Yan Li

    2011-01-01

    The mixed variables-attributes test plans for single acceptance sampling are proposed to protect “good lots” from attributes aspect and to optimize sample sizes from variables aspect. For the single and double mixed plans, exact formulas of the operating characteristic and average sample number are developed for the exponential distribution. Numerical illustrations show that the mixed sampling plans have some advantages over the variables plans or attributes plans alone.

  3. Test report for run-in acceptance testing of Project W-151 300 HP mixing pumps

    This report documents the results of a performance demonstration and operational checkout of three 300 HP mixer pumps in accordance with WHC-SD-WI51-TS-001 ''Mixer Pump Test Specification for Project W-151'' and Statement of Work 8K520-EMN-95-004 ''Mixer Pump Performance Demonstration at MASF'' in the 400 Area Maintenance and Storage Facility (MASF) building. Testing of the pumps was performed by Fast Flux Test Facility (FFTF) Engineering and funded by the Tank Waste Remediation System (TWRS) Project W-151. Testing began with the first pump on 04-01-95 and ended with the third pump on 11-01-96. Prior to testing, the MASF was modified and prepared to meet the pump testing requirements set forth by the Test Specification and the Statement of Work

  4. Social trust, risk perceptions and public acceptance of recycled water: testing a social-psychological model.

    Ross, Victoria L; Fielding, Kelly S; Louis, Winnifred R

    2014-05-01

    Faced with a severe drought, the residents of the regional city of Toowoomba, in South East Queensland, Australia were asked to consider a potable wastewater reuse scheme to supplement drinking water supplies. As public risk perceptions and trust have been shown to be key factors in acceptance of potable reuse projects, this research developed and tested a social-psychological model of trust, risk perceptions and acceptance. Participants (N = 380) were surveyed a few weeks before a referendum was held in which residents voted against the controversial scheme. Analysis using structural equation modelling showed that the more community members perceived that the water authority used fair procedures (e.g., consulting with the community and providing accurate information), the greater their sense of shared identity with the water authority. Shared social identity in turn influenced trust via increased source credibility, that is, perceptions that the water authority is competent and has the community's interest at heart. The findings also support past research showing that higher levels of trust in the water authority were associated with lower perceptions of risk, which in turn were associated with higher levels of acceptance, and vice versa. The findings have a practical application for improving public acceptance of potable recycled water schemes. PMID:24603028

  5. W-026 acceptance test report system integration equipment (SIE)(submittal {number_sign} 018.6.A)

    Watson, T.L.

    1997-01-27

    Acceptance testing of the System Integration Equipment (SIE) at Hanford was performed in two stages. The first was inconclusive, and resulted in a number of findings. These finding. are summarized as part of this report. The second stage of testing addressed these findings, and performed full system testing per the approved test procedure. This report includes summaries of all testing, results and finding.. Although the SIE did not in some cases perform as required for plant operations, it did perform per the system specification. (These discrepancies were noted and are addressed elsewhere.) Following testing, the system was formaLLy accepted. Documentation of this acceptance is incLuded in this report.

  6. Biological and chemical tests of contaminated soils to determine bioavailability and environmentally acceptable endpoints (EAE)

    The understanding of the concept of bioavailability of soil contaminants to receptors and its use in supporting the development of EAE is growing but still incomplete. Nonetheless, there is increased awareness of the importance of such data to determine acceptable cleanup levels and achieve timely site closures. This presentation discusses a framework for biological and chemical testing of contaminated soils developed as part of a Gas Research Institute (GRI) project entitled ''Environmentally Acceptable Endpoints in Soil Using a Risk Based Approach to Contaminated Site Management Based on Bioavailability of Chemicals in Soil.'' The presentation reviews the GRI program, and summarizes the findings of the biological and chemical testing section published in the GRI report. The three primary components of the presentation are: (1) defining the concept of bioavailability within the existing risk assessment paradigm, (2) assessing the usefulness of the existing tests to measure bioavailability and test frameworks used to interpret these measurements, and (3) suggesting how a small selection of relevant tests could be incorporated into a flexible testing scheme for soils to address this issue

  7. Cassini RTG acceptance test results and RTG performance on Galileo and Ulysses

    Flight acceptance testing has been completed for the RTGs to be used on the Cassini spacecraft which is scheduled for an October 6, 1997 launch to Saturn. The acceptance test program includes vibration tests, magnetic field measurements, mass properties (weight and c.g.) and thermal vacuum test. This paper presents the thermal vacuum test results. Three RTGs are to be used, F-2, F-6, and F-7. F-5 is the backup RTG, as it was for the Galileo and Ulysses missions launched in 1989 and 1990, respectively. RTG performance measured during the thermal vacuum tests carried out at the Mound Laboratory facility met all specification requirements. Beginning of mission (BOM) and end of mission (EOM) power predictions have been made based on these tests results. BOM power is predicted to be 888 watts compared to the minimum requirement of 826 watts. Degradation models predict the EOM power after 16 years is to be 640 watts compared to a minimum requirement of 596 watts. Results of small scale module tests are also shown. The modules contain couples from the qualification and flight production runs. The tests have exceeded 28,000 hours (3.2 years) and are continuing to provide increased confidence in the predicted long term performance of the Cassini RTGs. All test results indicate that the power requirements of the Cassini spacecraft will be met. BOM and EOM power margins of over 5% are predicted. Power output from telemetry for the two Galileo RTGs are shown from the 1989 launch to the recent Jupiter encounter. Comparisons of predicted, measured and required performance are shown. Telemetry data are also shown for the RTG on the Ulysses spacecraft which completed its planned mission in 1995 and is now in the extended mission

  8. Cassini RTG acceptance test results and RTG performance on Galileo and Ulysses

    Flight acceptance testing has been completed for the RTGs to be used on the Cassini spacecraft which is scheduled for an October 6, 1997 launch to Saturn. The acceptance test program includes vibration tests, magnetic field measurements, properties (weight and c.g.) and thermal vacuum test. This paper presents The thermal vacuum test results. Three RTGs are to be used, F-2, F-6, and F-7. F-5 is tile back-up RTG, as it was for the Galileo and Ulysses missions launched in 1989 and 1990, respectively. RTG performance measured during the thermal vacuum tests carried out at die Mound Laboratory facility met all specification requirements. Beginning of mission (BOM) and end of mission (EOM) power predictions have been made based on than tests results. BOM power is predicted to be 888 watts compared to the minimum requirement of 826 watts. Degradation models predict the EOM power after 16 years is to be 640 watts compared to a minimum requirement of 596 watts. Results of small scale module tests are also showing. The modules contain couples from the qualification and flight production runs. The tests have exceeded 28,000 hours (3.2 years) and are continuing to provide increased confidence in the predicted long term performance of the Cassini RTGs. All test results indicate that the power requirements of the Cassini spacecraft will be met. BOM and EOM power margins of over five percent are predicted. Power output from telemetry for the two Galileo RTGs are shown from the 1989 launch to the recent Jupiter encounter. Comparisons of predicted, measured and required performance are shown. Telemetry data are also shown for the RTG on the Ulysses spacecraft which completed its planned mission in 1995 and is now in the extended mission

  9. Space Suit Portable Life Support System (PLSS) 2.0 Pre-Installation Acceptance (PIA) Testing

    Anchondo, Ian; Cox, Marlon; Meginnis, Carly; Westheimer, David; Vogel, Matt R.

    2016-01-01

    Following successful completion of the space suit Portable Life Support System (PLSS) 1.0 development and testing in 2011, the second system-level prototype, PLSS 2.0, was developed in 2012 to continue the maturation of the advanced PLSS design. This advanced PLSS is intended to reduce consumables, improve reliability and robustness, and incorporate additional sensing and functional capabilities over the current Space Shuttle/International Space Station Extravehicular Mobility Unit (EMU) PLSS. PLSS 2.0 represents the first attempt at a packaged design comprising first generation or later component prototypes and medium fidelity interfaces within a flight-like representative volume. Pre-Installation Acceptance (PIA) is carryover terminology from the Space Shuttle Program referring to the series of test sequences used to verify functionality of the EMU PLSS prior to installation into the Space Shuttle airlock for launch. As applied to the PLSS 2.0 development and testing effort, PIA testing designated the series of 27 independent test sequences devised to verify component and subsystem functionality, perform in situ instrument calibrations, generate mapping data, define set-points, evaluate control algorithms, evaluate hardware performance against advanced PLSS design requirements, and provide quantitative and qualitative feedback on evolving design requirements and performance specifications. PLSS 2.0 PIA testing was carried out in 2013 and 2014 using a variety of test configurations to perform test sequences that ranged from stand-alone component testing to system-level testing, with evaluations becoming increasingly integrated as the test series progressed. Each of the 27 test sequences was vetted independently, with verification of basic functionality required before completion. Because PLSS 2.0 design requirements were evolving concurrently with PLSS 2.0 PIA testing, the requirements were used as guidelines to assess performance during the tests; after the

  10. Quality assurance in diagnostic radiology in Hungary - first experiences in acceptance testing

    It is a general experience that optimum imaging with minimum patient doses, moreover, the safe operation and long life of X-ray equipment can be assured by regular measurement of technical parameters and checking of their constancy (routine performance testing) only. These tests are generally known as quality control, while together with the so-called corrective actions and its management it is called (physical-technical) quality assurance (QA). In the European Union, Directive 97/43/EURATOM about radiation protection of patients requires - among others - the good practice of (physical-technical) quality assurance. In Hungary, Decree No. 31/2001. (X.3.) of the Minister of Health harmonizes all of its requirements. Acceptance testing of new diagnostic X-ray equipment is assigned to NPHC-NRIRR. QA has been a daily practice in radiation therapy and nuclear medicine for a long time. A National Patient Dose Assessment Programme has also successfully run since 1989. We had, however, only few preliminaries in QA in diagnostic radiology in the second half of the eighties. Nowadays there are running QA programmes in some hospitals and mammography centres. he testing activity of our institute is independent from manufacturers, it is run within the frame of an accredited testing laboratory, using calibrated measuring instruments and based on valid international standards. So the started way of implementing QA in diagnostic radiology needs a lot of further efforts, adapting experiences of other countries, and also some financial help to reach an acceptable level in the EU. (authors)

  11. User Acceptance Test of Computer-Assisted Problem-Based Learning Assessment Tool (CAPBLAT

    Muhammad Qomaruddin

    2014-02-01

    Full Text Available Problem-based Learning (PBL is an instructional design method that is used by many lecturers to create more efficient and meaningful learning experiences. PBL emphasizes the lecturer in facilitating in collaborative learning. They conventionally play a little role in the formal assessment process. Peer-assessment and self-assessment are the most frequent methods of assessment employed by the lecturers in conducting PBL approach. This paper presents acceptance testing of a computer-based tool for peer-assessment and self-assessment in PBL approach, which called Computer-Assisted Problem-Based Learning Assessment Tool (CAPBLAT. The tool was designed to assist a lecturer in conducting PBL teaching method and assess students learning progress. Two PBL classes participated in the testing of the tool. During the study, questionnaires were administered to students. The results concerning the assessment tool acceptance demonstrate that using CAPBLAT in the PBL assessment process received better acceptance from both the students and lecturers.

  12. Consumer acceptance, market test and market development of irradiated rice, dehydrated vegetables and spices

    Establishment of irradiation processing parameters, a quality assurance system, consumer acceptance, market test and market development of irradiated rice, dehydrated vegetables and spices were the activities carried out in this project by the Chinese Agricultural Irradiation Center. The results of the studies showed that the process dose for rice was 0.2-0.5 kGy when the non-uniformity was lower than 2.5, dose range for dehydrated vegetables was 5-7 kGy, dose for spices was 7-8 kGy. The system for quality assurance was established. The processing standards for several irradiated food items were set up. Market test showed that more than 70-80% of consumers accepted irradiated food. Industrial companies also accepted irradiated dehydrated vegetables and spices. The latter were successfully introduced to the markets and successful commercialization of irradiated garlic was followed. The economic benefit of operating the Chinese Agricultural Irradiation Center was analyzed and found attractive, especially for low dose irradiation of foods in sufficient supply. (author)

  13. Geoscience Laser Altimeter System (GLAS) Instrument: Flight Loop Heat Pipe (LHP) Acceptance Thermal Vacuum Test

    Baker, Charles; Butler, Dan; Ku, Jentung; Grob, Eric; Swanson, Ted; Nikitkin, Michael; Powers, Edward I. (Technical Monitor)

    2001-01-01

    Two loop heat pipes (LHPs) are to be used for tight thermal control of the Geoscience Laser Altimeter System (GLAS) instrument, planned for flight in late 2001. The LHPs are charged with Propylene as a working fluid. One LHP will be used to transport 110 W from a laser to a radiator, the other will transport 160 W from electronic boxes to a separate radiator. The application includes a large amount of thermal mass in each LHP system and low initial startup powers. The initial design had some non-ideal flight design compromises, resulted in a less than ideal charge level for this design concept with a symmetrical secondary wick. This less than ideal charge was identified as the source of inadequate performance of the flight LHPs during the flight thermal vacuum test in October of 2000. We modified the compensation chamber design, re-built and charged the LHPs for a final LHP acceptance thermal vacuum test. This test performed March of 2001 was 100% successful. This is the last testing to be performed on the LHPs prior to instrument thermal vacuum test. This sensitivity to charge level was shown through varying the charge on a Development Model Loop Heat Pipe (DM LHP) and evaluating performance at various fill levels. At lower fills similar to the original charge in the flight units, the same poor performance was observed. When the flight units were re-designed and filled to the levels similar to the initial successful DM LHP test, the flight units also successfully fulfilled all requirements. This final flight Acceptance test assessed performance with respect to startup, low power operation, conductance, and control heater power, and steady state control. The results of the testing showed that both LHPs operated within specification. Startup on one of the LHPs was better than the other LHP because of the starter heater placement and a difference in evaporator design. These differences resulted in a variation in the achieved superheat prior to startup. The LHP with

  14. Home-based voluntary HIV counselling and testing found highly acceptable and to reduce inequalities

    Michelo Charles

    2010-06-01

    Full Text Available Abstract Background Low uptake of voluntary HIV counselling and testing (VCT in sub-Saharan Africa is raising acceptability concerns which might be associated with ways by which it is offered. We investigated the acceptability of home-based delivery of counselling and HIV testing in urban and rural populations in Zambia where VCT has been offered mostly from local clinics. Methods A population-based HIV survey was conducted in selected communities in 2003 (n = 5035. All participants stating willingness to be HIV tested were offered VCT at home and all counselling was conducted in the participants' homes. In the urban area post-test counselling and giving of results were done the following day whereas in rural areas this could take 1-3 weeks. Results Of those who indicated willingness to be HIV tested, 76.1% (95%CI 74.9-77.2 were counselled and received the test result. Overall, there was an increase in the proportion ever HIV tested from 18% before provision of home-based VCT to 38% after. The highest increase was in rural areas; among young rural men aged 15-24 years up from 14% to 42% vs. for urban men from 17% to 37%. Test rates by educational attainment changed from being positively associated to be evenly distributed after home-based VCT. Conclusions A high uptake was achieved by delivering HIV counselling and testing at home. The highest uptakes were seen in rural areas, in young people and groups with low educational attainment, resulting in substantial reductions in existing inequalities in accessing VCT services.

  15. ENRAF Series 854 Advanced Technology Gauge (ATG) with SPU II card for Leak Detector Use Acceptance Test Procedure

    The following Acceptance Test Procedure was written to test the ENRAF series 854 ATG with SPU II card prior to installation in the Tank Farms. The procedure sets various parameters and verifies the gauge and alarms functionality

  16. ENRAF Series 854 Advanced Technology Gauge (ATG) with SPU ll Card for Leak Detector Use Acceptance Test Procedure

    The following Acceptance Test Procedure was written to test the Enraf Series 854 ATG with SPU-II card prior to installation in the Tank Farms. The procedure sets various parameters and verifies the gauge and the alarms functionality

  17. Ten years experience in acceptance testing of diagnostic radiology equipment in Hungary

    The EURATOM directive for the radiation protection of patients, which declares the mandatory evaluation of the performance of diagnostic X-ray machines, took effect in 1997. In Hungary, this became a harmonized act, the 31/2001. (X. 3.) decree of the Minister of Health. The most highlighted segment of the evaluation of technical performance is acceptance testing. The NRIRR Department of Radiohygiene performs acceptance tests since 2002. From then on we have performed more than 400 examinations on different modalities such as radiographic, fluoroscopic, DSA, mammographic, CT and dental panoramic X-rays. The tests were performed according to IEC = EN = MSZ EN international, European and at the same time Hungarian standards. This presentation discusses our experience and gives a comprehensive overview of the examinations by the evaluation of the measurement data. Our results show the importance of testing, done independently from the manufacturer and installer: in est. 25 % of the cases overall we have found inadequacies which required remedial action on the part of the service

  18. Evaluation of a standard test method and material for low-activity waste product acceptance

    The dissolution behavior of a candidate reference glass has been measured under a range of test conditions. The data base from these tests can be used to evaluate the credibility and validity of test results reported by Private Contractors as part of the acceptance process for immobilized low-activity waste (ILAW) products for DOE wastes. The LRM-1 glass that was used in the tests was formulated to be compositionally representative of anticipated ILAW products for Hanford and other Department of Energy sites. Replicate tests with this glass were used to measure the variability in the response (i.e., the solution concentrations of B, Na, and Si) under different test conditions. The glass was further evaluated for possible use as a standard material by analysis of its composition, microstructure, density, and compressive strength. In addition, the Na leachability index was measured with the ANS 16.1 test, and the Toxicity Characteristic Leach Procedure was run. The results of those tests and analyses are summarized

  19. Utility-Scale Parabolic Trough Solar Systems: Performance Acceptance Test Guidelines, April 2009 - December 2010

    Kearney, D.

    2011-05-01

    Prior to commercial operation, large solar systems in utility-size power plants need to pass a performance acceptance test conducted by the engineering, procurement, and construction (EPC) contractor or owners. In lieu of the present absence of ASME or other international test codes developed for this purpose, the National Renewable Energy Laboratory has undertaken the development of interim guidelines to provide recommendations for test procedures that can yield results of a high level of accuracy consistent with good engineering knowledge and practice. The Guidelines contained here are specifically written for parabolic trough collector systems with a heat-transport system using a high-temperature synthetic oil, but the basic principles are relevant to other CSP systems.

  20. Multi-Canister Overpack (MCO) Combustible Gas Management Leak Test Acceptance Criteria (OCRWM)

    The purpose of this document is to support the Spent Nuclear Fuel Project's combustible gas management strategy while avoiding the need to impose any requirements for oxygen free atmospheres within storage tubes that contain multi-canister overpacks (MCO). In order to avoid inerting requirements it is necessary to establish and confirm leak test acceptance criteria for mechanically sealed and weld sealed MCOs that are adequte to ensure that, in the unlikely event the leak test results for any MCO were to approach either of those criteria, it could still be handled and stored in stagnant air without compromising the SNF Project's overall strategy to prevent accumulation of combustible gas mixtures within MCOs or within their surroundings. To support that strategy, this document: (1) establishes combustible gas management functions and minimum functional requirements for the MCO's mechanical seals and closure weld(s); (2) establishes a maximum practical value for the minimum required initial MCO inert backfill gas pressure; and (3) based on items 1 and 2, establishes and confirms leak test acceptance criteria for the MCO's mechanical seal and final closure weld(s)

  1. Factory acceptance test of COLDDIAG: A cold vacuum chamber for diagnostics

    Gerstl, Stefan; Baumbach, Tilo; Casalbuoni, Sara; Grau, Andreas; Hagelstein, Michael; Saez de Jauregui, David; Holubek, Tomas [Karlsruhe Institute of Technology, Karlsruhe (Germany); Boffo, Cristian; Sikler, Guenther [Babcock Noell GmbH, Wuerzburg (Germany); Baglin, Vincent [CERN, Geneva (Switzerland); Cox, Matthew; Schouten, Jos [Diamond Light Source, Oxfordshire (United Kingdom); Cimino, Roberto; Commisso, Mario; Spataro, Bruno [INFN/LNF, Frascatti (Italy); Mostacci, Andrea [Rome University La Sapienza, Rome (Italy); Wallen, Eric [MAX-Lab, Lund (Sweden); Weigel, Ralf [Max-Planck Institute for Metal Research, Stuttgart (Germany); Clarke, Jim; Scott, Duncan [STFC/ASTeC, Daresbury (United Kingdom); Bradshaw, Tom [STFC/RAL, Chilton (United Kingdom); Jones, Roger; Shinton, Ian [University Manchester (United Kingdom)

    2011-07-01

    Superconductive insertion devices (IDs) have higher fields for a given gap and period length compared with the state of the art technology of permanent magnet IDs. This technological solution is very interesting for synchrotron light sources since it permits to increase the brilliance and/or the photon energy at moderate costs. One of the key issues for the development of superconducting IDs is the understanding of the beam heat load to the cold vacuum chamber. Therefore a cold vacuum chamber for diagnostic was built. Here we report about the design, planned measurements and the factory acceptance test of COLDDIAG.

  2. Factory acceptance test of COLDDIAG: A cold vacuum chamber for diagnostics

    Superconductive insertion devices (IDs) have higher fields for a given gap and period length compared with the state of the art technology of permanent magnet IDs. This technological solution is very interesting for synchrotron light sources since it permits to increase the brilliance and/or the photon energy at moderate costs. One of the key issues for the development of superconducting IDs is the understanding of the beam heat load to the cold vacuum chamber. Therefore a cold vacuum chamber for diagnostic was built. Here we report about the design, planned measurements and the factory acceptance test of COLDDIAG.

  3. Formulation of a candidate glass for use as an acceptance test standard material

    In this report, the authors discuss the formulation of a glass that will be used in a laboratory testing program designed to measure the precision of test methods identified in the privatization contracts for the immobilization of Hanford low-activity wastes. Tests will be conducted with that glass to measure the reproducibility of tests and analyses that must be performed by glass producers as a part of the product acceptance procedure. Test results will be used to determine if the contractually required tests and analyses are adequate for evaluating the acceptability of likely immobilized low-activity waste (ILAW) products. They will also be used to evaluate if the glass designed for use in these tests can be used as an analytical standard test material for verifying results reported by vendors for tests withg ILAW products. The results of those tests and analyses will be presented in a separate report. The purpose of this report is to document the strategy used to formulate the glass to be used in the testing program. The low-activity waste reference glass LRM that will be used in the testing program was formulated to be compositionally similar to ILAW products to be made with wastes from Hanford. Since the ILAW product compositions have not been disclosed by the vendors participating in the Hanford privatization project, the composition of LRM was formulated based on simulated Hanford waste stream and amounts of added glass forming chemicals typical for vitrified waste forms. The major components are 54 mass % SiO2, 20 mass % Na2O, 10 mass % Al2O3, 8 mass % B2O3, and 1.5 mass % K2O. Small amounts of other chemicals not present in Hanford wastes were also included in the glass, since they may be included as chemical additives in ILAW products. This was done so that the use of LRM as a composition standard could be evaluated. Radionuclides were not included in LRM because a nonradioactive material was desired

  4. The Rapid Integration and Test Environment - A Process for Achieving Software Test Acceptance

    Rick Jack

    2010-01-01

    The Rapid Integration and Test Environment (RITE) initiative, implemented by the Program Executive Office, Command, Control, Communications, Computers and Intelligence, Command and Control Program Office (PMW-150), was born of necessity. Existing processes for requirements definition and management, as well as those for software development, did not consistently deliver high-quality Navy command and control (C2) systems on time and within budget. Navy C2 software programs experienced an inc...

  5. Acceptance/operational test procedure 241-AN-107 Video Camera System

    This procedure will document the satisfactory operation of the 241-AN-107 Video Camera System. The camera assembly, including camera mast, pan-and-tilt unit, camera, and lights, will be installed in Tank 241-AN-107 to monitor activities during the Caustic Addition Project. The camera focus, zoom, and iris remote controls will be functionally tested. The resolution and color rendition of the camera will be verified using standard reference charts. The pan-and-tilt unit will be tested for required ranges of motion, and the camera lights will be functionally tested. The master control station equipment, including the monitor, VCRs, printer, character generator, and video micrometer will be set up and performance tested in accordance with original equipment manufacturer's specifications. The accuracy of the video micrometer to measure objects in the range of 0.25 inches to 67 inches will be verified. The gas drying distribution system will be tested to ensure that a drying gas can be flowed over the camera and lens in the event that condensation forms on these components. This test will be performed by attaching the gas input connector, located in the upper junction box, to a pressurized gas supply and verifying that the check valve, located in the camera housing, opens to exhaust the compressed gas. The 241-AN-107 camera system will also be tested to assure acceptable resolution of the camera imaging components utilizing the camera system lights

  6. For your interest? The ethical acceptability of using non-invasive prenatal testing to test 'purely for information'.

    Deans, Zuzana; Clarke, Angus J; Newson, Ainsley J

    2015-01-01

    Non-invasive prenatal testing (NIPT) is an emerging form of prenatal genetic testing that provides information about the genetic constitution of a foetus without the risk of pregnancy loss as a direct result of the test procedure. As with other prenatal tests, information from NIPT can help to make a decision about termination of pregnancy, plan contingencies for birth or prepare parents to raise a child with a genetic condition. NIPT can also be used by women and couples to test purely 'for information'. Here, no particular action is envisaged following the test; it is motivated entirely by an interest in the result. The fact that NIPT can be performed without posing a risk to the pregnancy could give rise to an increase in such requests. In this paper, we examine the ethical aspects of using NIPT 'purely for information', including the competing interests of the prospective parents and the future child, and the acceptability of testing for 'frivolous' reasons. Drawing on several clinical scenarios, we claim that arguments about testing children for genetic conditions are relevant to this debate. In addition, we raise ethical concerns over the potential for objectification of the child. We conclude that, in most cases, using NIPT to test for adult-onset conditions, carrier status or non-serious traits presenting in childhood would be unacceptable. PMID:25521970

  7. Accuracy and user-acceptability of HIV self-testing using an oral fluid-based HIV rapid test.

    Oon Tek Ng

    Full Text Available BACKGROUND: The United States FDA approved an over-the-counter HIV self-test, to facilitate increased HIV testing and earlier linkage to care. We assessed the accuracy of self-testing by untrained participants compared to healthcare worker (HCW testing, participants' ability to interpret sample results and user-acceptability of self-tests in Singapore. METHODOLOGY/PRINCIPAL FINDINGS: A cross-sectional study, involving 200 known HIV-positive patients and 794 unknown HIV status at-risk participants was conducted. Participants (all without prior self-test experience performed self-testing guided solely by visual instructions, followed by HCW testing, both using the OraQuick ADVANCE Rapid HIV 1/2 Antibody Test, with both results interpreted by the HCW. To assess ability to interpret results, participants were provided 3 sample results (positive, negative, and invalid to interpret. Of 192 participants who tested positive on HCW testing, self-testing was positive in 186 (96.9%, negative in 5 (2.6%, and invalid in 1 (0.5%. Of 794 participants who tested negative on HCW testing, self-testing was negative in 791 (99.6%, positive in 1 (0.1%, and invalid in 2 (0.3%. Excluding invalid tests, self-testing had sensitivity of 97.4% (95% CI 95.1% to 99.7% and specificity of 99.9% (95% CI: 99.6% to 100%. When interpreting results, 96%, 93.1% and 95.2% correctly read the positive, negative and invalid respectively. There were no significant demographic predictors for false negative self-testing or wrongly interpreting positive or invalid sample results as negative. Eighty-seven percent would purchase the kit over-the-counter; 89% preferred to take HIV tests in private. 72.5% and 74.9% felt the need for pre- and post-test counseling respectively. Only 28% would pay at least USD15 for the test. CONCLUSIONS/SIGNIFICANCE: Self-testing was associated with high specificity, and a small but significant number of false negatives. Incorrectly identifying model results as

  8. Community acceptability of use of rapid diagnostic tests for malaria by community health workers in Uganda

    Waiswa Peter

    2010-07-01

    Full Text Available Abstract Background Many malarious countries plan to introduce artemisinin combination therapy (ACT at community level using community health workers (CHWs for treatment of uncomplicated malaria. Use of ACT with reliance on presumptive diagnosis may lead to excessive use, increased costs and rise of drug resistance. Use of rapid diagnostic tests (RDTs could address these challenges but only if the communities will accept their use by CHWs. This study assessed community acceptability of the use of RDTs by Ugandan CHWs, locally referred to as community medicine distributors (CMDs. Methods The study was conducted in Iganga district using 10 focus group discussions (FGDs with CMDs and caregivers of children under five years, and 10 key informant interviews (KIIs with health workers and community leaders. Pre-designed FGD and KII guides were used to collect data. Manifest content analysis was used to explore issues of trust and confidence in CMDs, stigma associated with drawing blood from children, community willingness for CMDs to use RDTs, and challenges anticipated to be faced by the CMDs. Results CMDs are trusted by their communities because of their commitment to voluntary service, access, and the perceived effectiveness of anti-malarial drugs they provide. Some community members expressed fear that the blood collected could be used for HIV testing, the procedure could infect children with HIV, and the blood samples could be used for witchcraft. Education level of CMDs is important in their acceptability by the community, who welcome the use of RDTs given that the CMDs are trained and supported. Anticipated challenges for CMDs included transport for patient follow-up and picking supplies, adults demanding to be tested, and caregivers insisting their children be treated instead of being referred. Conclusion Use of RDTs by CMDs is likely to be acceptable by community members given that CMDs are properly trained, and receive regular technical

  9. Evaluation Of ARG-1 Samples Prepared By Cesium Carbonate Dissolution During The Isolok SME Acceptability Testing

    Evaluation of Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. The Mechanical Systems and Custom Equipment Development (MS and CED) Section of the Savannah River National Laboratory (SRNL) recently completed the evaluation of one of these opportunities - the possibility of using an Isolok sampling valve as an alternative to the Hydragard valve for taking DWPF process samples at the Slurry Mix Evaporator (SME). The use of an Isolok for SME sampling has the potential to improve operability, reduce maintenance time, and decrease CPC cycle time. The SME acceptability testing for the Isolok was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 and was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNLRP-2011-00145. RW-0333P QA requirements applied to the task, and the results from the investigation were documented in SRNL-STI-2011-00693. Measurement of the chemical composition of study samples was a critical component of the SME acceptability testing of the Isolok. A sampling and analytical plan supported the investigation with the analytical plan directing that the study samples be prepared by a cesium carbonate (Cs2CO3) fusion dissolution method and analyzed by Inductively Coupled Plasma - Optical Emission Spectroscopy (ICP-OES). The use of the cesium carbonate preparation method for the Isolok testing provided an opportunity for an additional assessment of this dissolution method, which is being investigated as a potential replacement for the two methods (i.e., sodium peroxide fusion and mixed acid dissolution) that have been used at the DWPF for the analysis of SME samples. Earlier testing of the Cs2CO3 method yielded promising results which led to a TTR from Savannah River Remediation, LLC (SRR) to SRNL for additional support and an associated TTQAP to direct the SRNL efforts. A technical report resulting from this work was

  10. EVALUATION OF ARG-1 SAMPLES PREPARED BY CESIUM CARBONATE DISSOLUTION DURING THE ISOLOK SME ACCEPTABILITY TESTING

    Edwards, T.; Hera, K.; Coleman, C.

    2011-12-05

    Evaluation of Defense Waste Processing Facility (DWPF) Chemical Process Cell (CPC) cycle time identified several opportunities to improve the CPC processing time. The Mechanical Systems & Custom Equipment Development (MS&CED) Section of the Savannah River National Laboratory (SRNL) recently completed the evaluation of one of these opportunities - the possibility of using an Isolok sampling valve as an alternative to the Hydragard valve for taking DWPF process samples at the Slurry Mix Evaporator (SME). The use of an Isolok for SME sampling has the potential to improve operability, reduce maintenance time, and decrease CPC cycle time. The SME acceptability testing for the Isolok was requested in Task Technical Request (TTR) HLW-DWPF-TTR-2010-0036 and was conducted as outlined in Task Technical and Quality Assurance Plan (TTQAP) SRNLRP-2011-00145. RW-0333P QA requirements applied to the task, and the results from the investigation were documented in SRNL-STI-2011-00693. Measurement of the chemical composition of study samples was a critical component of the SME acceptability testing of the Isolok. A sampling and analytical plan supported the investigation with the analytical plan directing that the study samples be prepared by a cesium carbonate (Cs{sub 2}CO{sub 3}) fusion dissolution method and analyzed by Inductively Coupled Plasma - Optical Emission Spectroscopy (ICP-OES). The use of the cesium carbonate preparation method for the Isolok testing provided an opportunity for an additional assessment of this dissolution method, which is being investigated as a potential replacement for the two methods (i.e., sodium peroxide fusion and mixed acid dissolution) that have been used at the DWPF for the analysis of SME samples. Earlier testing of the Cs{sub 2}CO{sub 3} method yielded promising results which led to a TTR from Savannah River Remediation, LLC (SRR) to SRNL for additional support and an associated TTQAP to direct the SRNL efforts. A technical report resulting

  11. The Careful Puppet Master: Reducing risk and fortifying acceptance testing with Jenkins CI

    Smith, Jason A.; Richman, Gabriel; DeStefano, John; Pryor, James; Rao, Tejas; Strecker-Kellogg, William; Wong, Tony

    2015-12-01

    Centralized configuration management, including the use of automation tools such as Puppet, can greatly increase provisioning speed and efficiency when configuring new systems or making changes to existing systems, reduce duplication of work, and improve automated processes. However, centralized management also brings with it a level of inherent risk: a single change in just one file can quickly be pushed out to thousands of computers and, if that change is not properly and thoroughly tested and contains an error, could result in catastrophic damage to many services, potentially bringing an entire computer facility offline. Change management procedures can—and should—be formalized in order to prevent such accidents. However, like the configuration management process itself, if such procedures are not automated, they can be difficult to enforce strictly. Therefore, to reduce the risk of merging potentially harmful changes into our production Puppet environment, we have created an automated testing system, which includes the Jenkins CI tool, to manage our Puppet testing process. This system includes the proposed changes and runs Puppet on a pool of dozens of RedHat Enterprise Virtualization (RHEV) virtual machines (VMs) that replicate most of our important production services for the purpose of testing. This paper describes our automated test system and how it hooks into our production approval process for automatic acceptance testing. All pending changes that have been pushed to production must pass this validation process before they can be approved and merged into production.

  12. Waste acceptance and the DWPF Startup Test Program: Impacts of process changes

    The DWPF is currently carrying out a Startup Test Program which will lead to radioactive operations in the facility. The objective of a significant portion of this program is to demonstrate that the DWPF can reliably make glass which satisfies DOE's product specifications. This objective will be achieved through a series of integrated process campaigns using feeds of various compositions (the Qualification Runs).2 During these campaigns, the DWPF Glass Product Control Programs (GPCP) will be used to ensure that glass is made which meets specifications. The GPCP uses a correlation between glass composition and leach test results to determine whether a particular batch of feed will make acceptable glass (i.e., glass which will meet the specifications)

  13. Acceptance tests for electrometers used in radiotherapy; Pruebas de aceptacion para electrometros usados en radioterapia

    Moreno-Torres, M.; Tornero-Lopez, A. M.; Ruiz-Arrebola, S.; Guirado, D.; Vilches, M.

    2015-05-01

    We present a set of tests designed to check the compliance of the requirements established in the standard IEC 60731:19972 and TRS 3981 technical report for reference class electrometers using the material normally available in a medical physics department. The characteristics under exam are: stability in the start-up, zero shift, zero drift, leakage current, linearity and repeatability. The method is applied to 4 electrometers: PTW UNIDOS, Sun Nuclear PC-Electrometer, Scanditronix-Wellhofer DOSE1 and Standard Imaging MAX4000. We checked that the electrometers comply with the requirements, although we detected some differences in the performance between them. The method proved itself precise enough and efficient to provide with reliable results for these tests and we consider it could be used to establish an internal procedure for the acceptance of this kind of equipment. (Author)

  14. Waste acceptance and the DWPF Startup Test Program: Impacts of process changes

    Plodinec, M.J.

    1992-08-24

    The DWPF is currently carrying out a Startup Test Program which will lead to radioactive operations in the facility. The objective of a significant portion of this program is to demonstrate that the DWPF can reliably make glass which satisfies DOE's product specifications. This objective will be achieved through a series of integrated process campaigns using feeds of various compositions (the Qualification Runs).2 During these campaigns, the DWPF Glass Product Control Programs (GPCP) will be used to ensure that glass is made which meets specifications. The GPCP uses a correlation between glass composition and leach test results to determine whether a particular batch of feed will make acceptable glass (i.e., glass which will meet the specifications).

  15. Waste acceptance and the DWPF Startup Test Program: Impacts of process changes

    Plodinec, M.J.

    1992-08-24

    The DWPF is currently carrying out a Startup Test Program which will lead to radioactive operations in the facility. The objective of a significant portion of this program is to demonstrate that the DWPF can reliably make glass which satisfies DOE`s product specifications. This objective will be achieved through a series of integrated process campaigns using feeds of various compositions (the Qualification Runs).2 During these campaigns, the DWPF Glass Product Control Programs (GPCP) will be used to ensure that glass is made which meets specifications. The GPCP uses a correlation between glass composition and leach test results to determine whether a particular batch of feed will make acceptable glass (i.e., glass which will meet the specifications).

  16. 10 CFR 26.91 - Acceptable devices for conducting initial and confirmatory tests for alcohol and methods of use.

    2010-01-01

    ... or that has passed its expiration date. (3) For ASDs that test breath specimens and meet EBT.... Alcohol screening devices (ASDs), including devices that test specimens of oral fluids or breath, must be...) Acceptable evidential breath testing devices. Evidential breath testing devices listed in the NHTSA CPL...

  17. A review of acceptance testing of the Los Alamos, Canberra Alpha Sentry Continuous Air Monitor (CAM)

    Los Alamos National Laboratory (LANL) undertook the design and development of a new generation of alpha continuous air monitor (CAM) instrumentation that would incorporate advanced technologies in the design of the sampling inlet, multi-channel analyzer (MCA) electronics, solid state alpha detectors, radon background interference suppression, background interference compensation and based on spectral analysis, and microcomputer based data communication, processing, storage, and retrieval. The ANSI air monitoring instrument standards (Performance Specifications for Health Physics Instrumentation -- Occupational Airborne Radioactivity Monitoring Instrumentation, N42.17B) specify performance criteria and testing procedures for instruments and instrument systems designed to continuously sample and quantify airborne radioactivity in the workplace. Although the intent of the standard is to provide performance testing criteria for type testing, it is appropriate to evaluate the performance of a new instrument such as the Alpha Sentry against certain of these criteria for purposes of an acceptance test based on stated specifications and the Los Alamos CAM Requirements document. This report provides an overview of the results of these tests, as they pertain to instruments designed to detect alpha-emitting radionuclides in particulate form

  18. SU-E-P-46: Clinical Acceptance Testing and Implementation of a Portable CT Unit

    Purpose: Planning for the first installation in New England of a new portable CT unit to be used in the Operating Room required the integration of many departments including Surgery, Neurosurgery, Information Services, Clinical Engineering, Radiology and Medical Physics/Radiation Safety. Acceptance testing and the quality assurance procedures were designed to optimize image quality and patient and personnel radiation exposure. Methods: The vendor’s protocols were tested using the CT Dosimetry phantoms. The system displayed the CTDIw instead of the CTDIvol while testing the unit. Radiation exposure was compared to existing CT scanners from installed CT units throughout the facility. Brainlab measures all 4 periphery slots on the CT Dosimetry phantom. The ACR measures only the superior slot for the periphery measurement. A comprehensive radiation survey was also performed for several locations. Results: The CTDIvol measurements were comparable for the following studies: brain, C-Spine, and sinuses. However, the mobile CT measurements were slightly higher than other CT units but within acceptable tolerance if measured using the ACR method.Based on scatter measurements, it was determined if any personnel were to stay in the OR Suite during image acquisition that the appropriate lead apron and thyroid shields had to be worn.In addition, to reduce unnecessary scatter, there were two mobile 6 foot wide shields (1/16″ lead equivalent) available to protect personnel in the room and adjacent areas. Conclusion: Intraoperative CT provides the physician new opportunities for evaluation of the progression of surgical resections and device placement at the cost of increasing the amount of trained personnel required to perform this procedure. It also brings with it challenges to keep the radiation exposure to the patients and staff within reasonable limits

  19. SU-E-P-46: Clinical Acceptance Testing and Implementation of a Portable CT Unit

    LaFrance, M; Marsh, S; Hicks, R; O’Donnell-Moran, G [Baystate Health Systems, Inc., Springfield, MA (United States)

    2015-06-15

    Purpose: Planning for the first installation in New England of a new portable CT unit to be used in the Operating Room required the integration of many departments including Surgery, Neurosurgery, Information Services, Clinical Engineering, Radiology and Medical Physics/Radiation Safety. Acceptance testing and the quality assurance procedures were designed to optimize image quality and patient and personnel radiation exposure. Methods: The vendor’s protocols were tested using the CT Dosimetry phantoms. The system displayed the CTDIw instead of the CTDIvol while testing the unit. Radiation exposure was compared to existing CT scanners from installed CT units throughout the facility. Brainlab measures all 4 periphery slots on the CT Dosimetry phantom. The ACR measures only the superior slot for the periphery measurement. A comprehensive radiation survey was also performed for several locations. Results: The CTDIvol measurements were comparable for the following studies: brain, C-Spine, and sinuses. However, the mobile CT measurements were slightly higher than other CT units but within acceptable tolerance if measured using the ACR method.Based on scatter measurements, it was determined if any personnel were to stay in the OR Suite during image acquisition that the appropriate lead apron and thyroid shields had to be worn.In addition, to reduce unnecessary scatter, there were two mobile 6 foot wide shields (1/16″ lead equivalent) available to protect personnel in the room and adjacent areas. Conclusion: Intraoperative CT provides the physician new opportunities for evaluation of the progression of surgical resections and device placement at the cost of increasing the amount of trained personnel required to perform this procedure. It also brings with it challenges to keep the radiation exposure to the patients and staff within reasonable limits.

  20. Compliance with the Nevada Test Site's waste acceptance criteria for vitrified cesium-loaded crystalline silicotitanates

    As part of a joint project between the Oak Ridge National Laboratory (ORNL) and the Savannah River Technology Center (SRTC), Cs-137 loaded crystalline silicotitanate (CST) sorbent will be vitrified in a joule-heated melter. Glass formulation development for this CST sorbent is discussed in an accompanying abstract for this conference. One of the objectives for this project was to ensure that the vitrified waste form could be disposed of at the Nevada Test Site (NTS). To accomplish this objective, the waste form must meet the NTS Waste Acceptance Criteria (WAC). This paper presents SRTC's efforts at ensuring that the glass waste form produced as a result of vitrification of CST will meet all of the criteria of the WAC. The producer must demonstrate that the waste is neither TRU nor mixed, and that the glass has a radionuclide content which is less than the Class C limit of 4,600 Ci/m3. The impact of this requirement on the CST loading in the glass is discussed along with the benefits to the producer which result if greater than Class C waste is accepted by NTS since this limit may be relaxed in the near future. This paper demonstrates that vitrification leads to a waste form which meets all of the criteria of the NTS WAC

  1. Understanding Student Teachers’ Behavioural Intention to Use Technology: Technology Acceptance Model (TAM Validation and Testing

    Kung-Teck, Wong

    2013-01-01

    Full Text Available This study sets out to validate and test the Technology Acceptance Model (TAM in the context of Malaysian student teachers’ integration of their technology in teaching and learning. To establish factorial validity, data collected from 302 respondents were tested against the TAM using confirmatory factor analysis (CFA, and structural equation modelling (SEM was used for model comparison and hypotheses testing. The goodness-of-fit test of the analysis shows partial support of the applicability of the TAM in a Malaysian context. Overall, the TAM accounted for 37.3% of the variance in intention to use technology among student teachers and of the five hypotheses formulated, four are supported. Perceived usefulness is a significant influence on attitude towards computer use and behavioural intention. Perceived ease of use significantly influences perceived usefulness, and finally, behavioural intention is found to be influenced by attitude towards computer use. The findings of this research contribute to the literature by validating the TAM in the Malaysian context and provide several prominent implications for the research and practice of technology integration development.

  2. Full-Scale Cask Testing and Public Acceptance of Spent Nuclear Fuel Shipments - 12254

    Full-scale physical testing of spent fuel shipping casks has been proposed by the National Academy of Sciences (NAS) 2006 report on spent nuclear fuel transportation, and by the Presidential Blue Ribbon Commission (BRC) on America's Nuclear Future 2011 draft report. The U.S. Nuclear Regulatory Commission (NRC) in 2005 proposed full-scale testing of a rail cask, and considered 'regulatory limits' testing of both rail and truck casks (SRM SECY-05-0051). The recent U.S. Department of Energy (DOE) cancellation of the Yucca Mountain project, NRC evaluation of extended spent fuel storage (possibly beyond 60-120 years) before transportation, nuclear industry adoption of very large dual-purpose canisters for spent fuel storage and transport, and the deliberations of the BRC, will fundamentally change assumptions about the future spent fuel transportation system, and reopen the debate over shipping cask performance in severe accidents and acts of sabotage. This paper examines possible approaches to full-scale testing for enhancing public confidence in risk analyses, perception of risk, and acceptance of spent fuel shipments. The paper reviews the literature on public perception of spent nuclear fuel and nuclear waste transportation risks. We review and summarize opinion surveys sponsored by the State of Nevada over the past two decades, which show consistent patterns of concern among Nevada residents about health and safety impacts, and socioeconomic impacts such as reduced property values along likely transportation routes. We also review and summarize the large body of public opinion survey research on transportation concerns at regional and national levels. The paper reviews three past cask testing programs, the way in which these cask testing program results were portrayed in films and videos, and examines public and official responses to these three programs: the 1970's impact and fire testing of spent fuel truck casks at Sandia National Laboratories, the 1980's

  3. Full-Scale Cask Testing and Public Acceptance of Spent Nuclear Fuel Shipments - 12254

    Dilger, Fred [Black Mountain Research, Henderson, NV 81012 (United States); Halstead, Robert J. [State of Nevada Agency for Nuclear Projects Carson City, NV 80906 (United States); Ballard, James D. [Department of Sociology, California State University, Northridge Northridge, CA 91330 (United States)

    2012-07-01

    Full-scale physical testing of spent fuel shipping casks has been proposed by the National Academy of Sciences (NAS) 2006 report on spent nuclear fuel transportation, and by the Presidential Blue Ribbon Commission (BRC) on America's Nuclear Future 2011 draft report. The U.S. Nuclear Regulatory Commission (NRC) in 2005 proposed full-scale testing of a rail cask, and considered 'regulatory limits' testing of both rail and truck casks (SRM SECY-05-0051). The recent U.S. Department of Energy (DOE) cancellation of the Yucca Mountain project, NRC evaluation of extended spent fuel storage (possibly beyond 60-120 years) before transportation, nuclear industry adoption of very large dual-purpose canisters for spent fuel storage and transport, and the deliberations of the BRC, will fundamentally change assumptions about the future spent fuel transportation system, and reopen the debate over shipping cask performance in severe accidents and acts of sabotage. This paper examines possible approaches to full-scale testing for enhancing public confidence in risk analyses, perception of risk, and acceptance of spent fuel shipments. The paper reviews the literature on public perception of spent nuclear fuel and nuclear waste transportation risks. We review and summarize opinion surveys sponsored by the State of Nevada over the past two decades, which show consistent patterns of concern among Nevada residents about health and safety impacts, and socioeconomic impacts such as reduced property values along likely transportation routes. We also review and summarize the large body of public opinion survey research on transportation concerns at regional and national levels. The paper reviews three past cask testing programs, the way in which these cask testing program results were portrayed in films and videos, and examines public and official responses to these three programs: the 1970's impact and fire testing of spent fuel truck casks at Sandia National

  4. Source test of the prototype neutron detector for the large-acceptance multipurpose spectrometer at RAON

    Lee, Kisoo; Lee, Kyong Sei; Mulilo, Benard; Hong, Byungsik

    2013-05-01

    A neutron detector array will be essential for the study of the nuclear symmetry energy in the large-acceptance multipurpose spectrometer (LAMPS) at the planned rare-isotope beam facility RAON in Korea. We have built the prototype neutron detector for LAMPS and examined its performance by using radiation sources. For data taking, we tested the voltage-threshold discriminator (VTD) and the constant-fraction discriminator (CFD) modules for the pulse process. The intrinsic time resolution of the prototype detector is estimated to be 723 ps for VTD and 488 ps for CFD. The fission neutrons and gammas emitted from 252Cf can be clearly separated in the time distribution. We reconstruct the energy spectrum of the spontaneous fission neutrons from 252Cf, which can be described well by using the empirical Watt spectrum.

  5. Department of Defense picture archiving and communication system acceptance testing: results and identification of problem components.

    Allison, Scott A; Sweet, Clifford F; Beall, Douglas P; Lewis, Thomas E; Monroe, Thomas

    2005-09-01

    The PACS implementation process is complicated requiring a tremendous amount of time, resources, and planning. The Department of Defense (DOD) has significant experience in developing and refining PACS acceptance testing (AT) protocols that assure contract compliance, clinical safety, and functionality. The DOD's AT experience under the initial Medical Diagnostic Imaging Support System contract led to the current Digital Imaging Network-Picture Archiving and Communications Systems (DIN-PACS) contract AT protocol. To identify the most common system and component deficiencies under the current DIN-PACS AT protocol, 14 tri-service sites were evaluated during 1998-2000. Sixteen system deficiency citations with 154 separate types of limitations were noted with problems involving the workstation, interfaces, and the Radiology Information System comprising more than 50% of the citations. Larger PACS deployments were associated with a higher number of deficiencies. The most commonly cited systems deficiencies were among the most expensive components of the PACS. PMID:15924273

  6. Factors associated with willingness to accept oral fluid HIV rapid testing among most-at-risk populations in China.

    Huanmiao Xun

    Full Text Available BACKGROUND: The availability of oral fluid HIV rapid testing provides an approach that may have the potential to expand HIV testing in China, especially among most-a-risk populations. There are few investigations about the acceptability of oral fluid HIV testing among most-at-risk populations in China. METHOD: A cross-sectional study with men who have sex with men (MSM, female sex workers (FSW and voluntary counseling and testing (VCT clients was conducted in three cities of Shandong province, China from 2011 to 2012. Data were collected by face-to-face questionnaire. RESULTS: About 71% of participants were willing to accept the oral fluid HIV rapid testing, and home HIV testing was independently associated with acceptability of the new testing method among MSM, FSW and VCT clients (AOR of 4.46, 3.19 and 5.74, respectively. Independent predictors of oral fluid HIV rapid testing acceptability among MSM were having ever taken an oral fluid HIV rapid test (AOR= 15.25, having ever taken an HIV test (AOR= 2.07, and education level (AOR= 1.74. Engagement in HIV-related risk behaviors (AOR= 1.68 was an independent predictor of acceptability for FSW. Having taken an HIV test (AOR= 2.85 was an independent predictor of acceptability for VCT clients. The primary concern about the oral fluid HIV testing was accuracy. The median price they would pay for the testing ranged from 4.8 to 8.1 U.S. dollars. CONCLUSION: High acceptability of oral fluid HIV rapid testing was shown among most-at-risk populations. Findings provide support for oral rapid HIV testing as another HIV prevention tool, and provide a backdrop for the implementation of HIV home testing in the near future. Appropriate pricing and increased public education through awareness campaigns that address concerns about the accuracy and safety of the oral fluid HIV rapid testing may help increase acceptability and use among most-at-risk populations in China.

  7. Acceptability and feasibility of HIV self-testing among men who have sex with men in Peru and Brazil.

    Volk, Jonathan E; Lippman, Sheri A; Grinsztejn, Beatriz; Lama, Javier R; Fernandes, Nilo M; Gonzales, Pedro; Hessol, Nancy A; Buchbinder, Susan

    2016-06-01

    HIV self-testing has the potential to increase testing frequency and uptake. This pilot study assessed the feasibility and acceptability of HIV self-testing in a sample of sexually active men who have sex with men (MSM) in Peru and Brazil. Participants were trained to use a whole blood rapid HIV self-test and instructed to use the self-test monthly during this three-month study. Test acceptability was measured with self-reported use of the test at the one-month and three-month study visits, and test feasibility was assessed by direct observation of self-test administration at the final three-month visit. A total of 103 participants (52 in Peru and 51 in Brazil) were enrolled, and 86% completed the three-month study. Nearly all participants reported use of the self-test (97% at one-month and 98% at three-month visit), and all participants correctly interpreted the self-administered test results when observed using the test at the final study visit. HIV self-testing with a blood-based assay was highly acceptable and feasible. HIV self-testing may have the potential to increase testing frequency and to reach high-risk MSM not currently accessing HIV-testing services. PMID:25971262

  8. Record and Verify Systems for Radiation Treatment of Cancer: Acceptance Testing, Commissioning and Quality Control

    Quality assurance (QA) in the radiation therapy treatment planning and delivery process is essential to ensure accurate dose delivery to the patient and to minimize the possibility of accidental exposure. To support this, computerized record and verify systems (RVSs) are now widely available in both industrialized and low and middle income countries. Recent publications of errors in radiation therapy have demonstrated that the lack of proper QA procedures for RVSs can result in severe accidents, including death, as a result of accidental exposure. Furthermore, the use of RVSs can have a higher risk of repeated errors due to a false sense of security out of belief that a computerized RVS will generate safer treatment procedures. It is widely acknowledged that there are very few reports in the peer reviewed literature and no guidance documents available that professionals can follow for a systematic verification of all functionalities of RVSs and their related interfaces with imaging systems, treatment planning computers and treatment delivery systems. The need to develop specific guidelines for acceptance testing, commissioning and quality control of RVSs has been identified through the increased interest of Member States in efficient and safe radiotherapy treatment. To meet this need, the IAEA has convened several consultants meetings to prepare a publication for establishing QA for RVSs. A draft report was generated by the consultants and was submitted for review by manufacturers of RVSs. Furthermore, the draft report was field tested at the General Hospital (Allgemeines Krankenhaus) in Vienna, Austria. The comments of the manufacturers and field testing were incorporated in the revised document where appropriate. This report is intended mainly for radiotherapy medical physicists, but the information is also useful for radiation oncologists and therapy radiographers working in radiotherapy hospitals. In addition, the guidance given in this report is highly

  9. Acceptability of rapid oral fluid HIV testing among male injection drug users in Taiwan, 1997 and 2007.

    Lyu, Shu-Yu; Morisky, Donald E; Yeh, Ching-Ying; Twu, Shiing-Jer; Peng, Eugene Yu-Chang; Malow, Robert M

    2011-04-01

    Rapid oral fluid HIV testing (rapid oral testing) is in the process of being adapted in Taiwan and elsewhere given its advantages over prior HIV testing methods. To guide this process, we examined the acceptability of rapid oral testing at two time points (i.e., 1997 and 2007) among one of the highest risk populations, male injection drug users (IDUs). For this purpose, an anonymous self-administered survey was completed by HIV-negative IDUs involved in the criminal justice system in 1997 (N (1)=137 parolees) and 2007 (N (2)=106 prisoners). A social marketing model helped guide the design of our questionnaire to assess the acceptability of rapid oral testing. This included assessing a new product, across four marketing dimensions: product, price, promotion, and place. Results revealed that in both 1997 and 2007, over 90% indicated that rapid oral testing would be highly acceptable, particularly if the cost was under US$6, and that a pharmacy would be the most appropriate and accessible venue for selling the rapid oral testing kits. The vast majority of survey respondents believed that the cost of rapid oral testing should be federally subsidized and that television and newspaper advertisements would be the most effective media to advertise for rapid oral testing. Both the 1997 and 2007 surveys suggested that rapid oral HIV testing would be particularly accepted in Taiwan by IDUs after release from the criminal justice system. PMID:21271392

  10. Scaling of Lift Degradation Due to Anti-Icing Fluids Based Upon the Aerodynamic Acceptance Test

    Broeren, Andy P.; Riley, James T.

    2012-01-01

    In recent years, the FAA has worked with Transport Canada, National Research Council Canada (NRC) and APS Aviation, Inc. to develop allowance times for aircraft operations in ice-pellet precipitation. These allowance times are critical to ensure safety and efficient operation of commercial and cargo flights. Wind-tunnel testing with uncontaminated anti-icing fluids and fluids contaminated with simulated ice pellets had been carried out at the NRC Propulsion and Icing Wind Tunnel (PIWT) to better understand the flowoff characteristics and resulting aerodynamic effects. The percent lift loss on the thin, high-performance wing model tested in the PIWT was determined at 8 angle of attack and used as one of the evaluation criteria in determining the allowance times. Because it was unclear as to how performance degradations measured on this model were relevant to an actual airplane configuration, some means of interpreting the wing model lift loss was deemed necessary. This paper describes how the lift loss was related to the loss in maximum lift of a Boeing 737-200ADV airplane through the Aerodynamic Acceptance Test (AAT) performed for fluids qualification. A loss in maximum lift coefficient of 5.24 percent on the B737-200ADV airplane (which was adopted as the threshold in the AAT) corresponds to a lift loss of 7.3 percent on the PIWT model at 8 angle of attack. There is significant scatter in the data used to develop the correlation related to varying effects of the anti-icing fluids that were tested and other factors. A statistical analysis indicated the upper limit of lift loss on the PIWT model was 9.2 percent. Therefore, for cases resulting in PIWT model lift loss from 7.3 to 9.2 percent, extra scrutiny of the visual observations is required in evaluating fluid performance with contamination.

  11. Results of the NASA Kennedy Space Center 50-MHz Doppler Radar Wind Profiler Operational Acceptance Test

    Barbre', Robert E., Jr.; Decker, Ryan K.; Leahy, Frank B.; Huddleston, Lisa

    2016-01-01

    This paper presents results of the new Kennedy Space Center (KSC) 50-MHz Doppler Radar Wind Profiler (DRWP) Operational Acceptance Test (OAT). The goal of the OAT was to verify the data quality of the new DRWP against the performance of the previous DRWP in order to use wind data derived by the new DRWP for space launch vehicle operations support at the Eastern Range. The previous DRWP was used as a situational awareness asset for mission operations to identify rapid changes in the wind environment that weather balloons cannot depict. The Marshall Space Flight Center's Natural Environments Branch assessed data from the new DRWP collected during Jan-Feb 2015 against a specified set of test criteria. Data examination verified that the DRWP provides complete profiles every five minutes from 1.8-19.5 km in vertical increments of 150 m. Analysis of 49 concurrent DRWP and balloon profiles presented root mean square wind component differences around 2.0 m/s. Evaluation of the DRWP's coherence between five-minute wind pairs found the effective vertical resolution to be Nyquist-limited at 300 m for both wind components. In addition, the sensitivity to rejecting data that do not have adequate signal was quantified. This paper documents the data, quality control procedures, methodology, and results of each analysis.

  12. Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

    Mattigod, Shas V.; Westsik, Joseph H.; Chung, Chul-Woo; Lindberg, Michael J.; Parker, Kent E.

    2011-08-12

    To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions has initiated secondary-waste-form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is conducting tests on four candidate waste forms to evaluate their ability to meet potential waste acceptance criteria for immobilized secondary wastes that would be placed in the IDF. All three waste forms demonstrated compressive strengths above the minimum 3.45 MPa (500 psi) set as a target for cement-based waste forms. Further, none of the waste forms showed any significant degradation in compressive strength after undergoing thermal cycling (30 cycles in a 10 day period) between -40 C and 60 C or water immersion for 90 days. The three leach test methods are intended to measure the diffusion rates of contaminants from the waste forms. Results are reported in terms of diffusion coefficients and a leachability index (LI) calculated based on the diffusion coefficients. A smaller diffusion coefficient and a larger LI are desired. The NRC, in its Waste Form Technical Position (NRC 1991), provides recommendations and guidance regarding methods to demonstrate waste stability for land disposal of radioactive waste. Included is a recommendation to conduct leach tests using the ANS 16.1 method. The resulting leachability index (LI) should be greater than 6.0. For Hanford secondary wastes, the LI > 6.0 criterion applies to sodium leached from the waste form. For technetium and iodine, higher targets of LI > 9 for Tc and LI > 11 for iodine have been set based on early waste-disposal risk and performance assessment analyses. The results of these three leach tests conducted for a total time between 11days (ASTM C1308) to 90 days (ANS 16.1) showed: (1) Technetium diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that

  13. Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

    To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions has initiated secondary-waste-form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is conducting tests on four candidate waste forms to evaluate their ability to meet potential waste acceptance criteria for immobilized secondary wastes that would be placed in the IDF. All three waste forms demonstrated compressive strengths above the minimum 3.45 MPa (500 psi) set as a target for cement-based waste forms. Further, none of the waste forms showed any significant degradation in compressive strength after undergoing thermal cycling (30 cycles in a 10 day period) between -40 C and 60 C or water immersion for 90 days. The three leach test methods are intended to measure the diffusion rates of contaminants from the waste forms. Results are reported in terms of diffusion coefficients and a leachability index (LI) calculated based on the diffusion coefficients. A smaller diffusion coefficient and a larger LI are desired. The NRC, in its Waste Form Technical Position (NRC 1991), provides recommendations and guidance regarding methods to demonstrate waste stability for land disposal of radioactive waste. Included is a recommendation to conduct leach tests using the ANS 16.1 method. The resulting leachability index (LI) should be greater than 6.0. For Hanford secondary wastes, the LI > 6.0 criterion applies to sodium leached from the waste form. For technetium and iodine, higher targets of LI > 9 for Tc and LI > 11 for iodine have been set based on early waste-disposal risk and performance assessment analyses. The results of these three leach tests conducted for a total time between 11days (ASTM C1308) to 90 days (ANS 16.1) showed: (1) Technetium diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that

  14. Client characteristics and acceptability of a home-based HIV counselling and testing intervention in rural South Africa

    Naik, Reshma; Tabana, Hanani; Doherty, Tanya; Zembe, Wanga; Jackson, Debra

    2012-01-01

    Background HIV counselling and testing (HCT) is a critical gateway for addressing HIV prevention and linking people to treatment, care, and support. Since national testing rates are often less than optimal, there is growing interest in expanding testing coverage through the implementation of innovative models such as home-based HIV counselling and testing (HBHCT). With the aim of informing scale up, this paper discusses client characteristics and acceptability of an HBHCT intervention impleme...

  15. Client characteristics and acceptability of a home-based HIV counselling and testing intervention in rural South Africa

    Naik Reshma; Tabana Hanani; Doherty Tanya; Zembe Wanga; Jackson Debra

    2012-01-01

    Abstract Background HIV counselling and testing (HCT) is a critical gateway for addressing HIV prevention and linking people to treatment, care, and support. Since national testing rates are often less than optimal, there is growing interest in expanding testing coverage through the implementation of innovative models such as home-based HIV counselling and testing (HBHCT). With the aim of informing scale up, this paper discusses client characteristics and acceptability of an HBHCT interventio...

  16. Delinquency and Peer Acceptance in Adolescence: A Within-Person Test of Moffitt's Hypotheses

    Rulison, Kelly L.; Kreager, Derek A.; Osgood, D. Wayne

    2014-01-01

    We tested 2 hypotheses derived from Moffitt's (1993) taxonomic theory of antisocial behavior, both of which are central to her explanation for the rise in delinquency during adolescence. We tested whether persistently delinquent individuals become more accepted by their peers during adolescence and whether individuals who abstain from…

  17. Electrical/instrumentation acceptance test report for Project C-018H, 242-A Evaporator/PUREX Plant condensate treatment facility

    This project is part of the 200 Area Effluent Treatment Facility. The acceptance test procedure describes test methods for leak detection units, pump flow switches, pump level control valves, room air temperature monitor, leachate pump status contacts, basin pump status contacts, catch basin leak detector, leachate level monitors, and basin level monitors. These are all components of the C-018H Collection System

  18. Application of ultrasonic testing as acceptance test for the graphite component of HTTR (High Temperature Test Reactor)

    Ultrasonic testing method for the nuclear grade graphite was established. The effectiveness of this method was demonstrated through the application for the graphite component of the HTTR. The characteristics of noise echo were also investigated by relating with mechanical properties. (author). 2 refs., 6 figs., 3 tabs

  19. Value Acceptance on Adolescent Socialization: A Test of a Cognitive-Functional Theory of Television Effects.

    Tan, Alexis; Nelson, Leigh; Dong, Qingwen; Tan, Gerdean

    1997-01-01

    Presents a cognitive-functional explanation of television's influence on Anglo-American, Native American, and Hispanic adolescents' acceptance of values. Finds that adolescents accepted values observed in television when they recognized them (a measure of learning) and when they evaluated the values to be important in "being successful" in the…

  20. Acceptance of referral for partners by clients testing positive for human immunodeficiency virus

    Netsanet F

    2013-01-01

    Full Text Available Fetene Netsanet,1 Ayalew Dessie21IMA World Health SuddHealth Multi Donor Trust Fund-Basic Package of Health Services Project, Juba, South Sudan; 2United States Agency for International Development, Private Health Sector Program, Abt Associates Inc, Addis Ababa, EthiopiaBackground: Human immunodeficiency virus (HIV-positive individuals who do not disclose their HIV status to their partners are more likely to present late for HIV and acquired immune deficiency syndrome (AIDS care than those who have disclosed their HIV status to their partners. A major area of challenge with regards to HIV counseling for clients is disclosure of their HIV status to their partners. The main methods of partner notification are patient referral, provider referral, contract referral, and outreach assistance. The emphasis on a plausible and comprehensive partner referral strategy for widespread positive case detection in resource-limited countries needs to be thought out and developed.Methods: A qualitative study was conducted among newly HIV-positive clients to identify partners for notification and acceptance of referral by their partners. Health service providers working in HIV testing and counseling clinics were also provided with semistructured questionnaires in order to assess their view towards partner notification strategies for clients testing positive for HIV.Results: Fifteen newly diagnosed HIV-positive clients were counseled to provide referral slips to their partners. All clients agreed and took the referral card. However, only eight were willing and actually provided the card to their partners. Five of the eight partners of clients who tested HIV-positive and who were provided with referral cards responded to the referral and were tested for HIV. Three were positive and two were negative. Nine of 11 counselors did not agree to requesting partner locator information from HIV-positive clients for contractual referral and/or outreach assistance. The findings

  1. A data base and a standard material for use in acceptance testing of low-activity waste products

    The authors have conducted replicate dissolution tests following the product consistency test (PCT) procedure to measure the mean and standard deviation of the solution concentrations of B, Na, and Si at various combinations of temperature, duration, and glass/water mass ratio. Tests were conducted with a glass formulated to be compositionally similar to low-activity waste products anticipated for Hanford to evaluate the adequacy of test methods that have been designated in privatization contracts for use in product acceptance. An important finding from this set of tests is that the solution concentrations generated in tests at 20 C will likely be too low to measure the dissolution rates of waste products reliably. Based on these results, the authors recommend that the acceptance test be conducted at 40 C. Tests at 40 C generated higher solution concentrations, were more easily conducted, and the measured rates were easily related to those at 20 C. Replicate measurements of other glass properties were made to evaluate the possible use of LRM-1 as a standard material. These include its composition, homogeneity, density, compressive strength, the Na leachability index with the ANSI/ANS 16.1 leach test, and if the glass is characteristically hazardous with the toxicity characteristic leach procedure. The values of these properties were within the acceptable limits identified for Hanford low-activity waste products. The reproducibility of replicate tests and analyses indicates that the glass would be a suitable standard material

  2. W-026 acceptance test report plant control system software(submittal {number_sign}223.02)

    Watson, T.L.

    1997-02-14

    Acceptance Testing of the WRAP 1 Plant Control System software was conducted throughout the construction of WRAP 1 with final testing on the glovebox software being completed in December 1996. The software tests were broken out into five sections; one for each of the four Local Control Units and one for the supervisory software modules. This document contains a completed copy of the software tests along with the applicable test log and completed Exception Test Reports. The ETRs outside the scope of the contractor are not signed off. These will be resolved by the Buyer and all 1280 open issues will be tracked on Buyer`s ETR database pending resolution.

  3. Optimization of the general acceptability though affective tests and response surface methodology of a dry cacao powder mixture based beverage

    Elena Chau Loo Kung

    2013-09-01

    Full Text Available This research work had as main objective optimizing the general acceptability though affective tests and response surface methodology of a dry cacao powder mixture based beverage. We obtained formulations of mixtures of cacao powder with different concentrations of 15%, 17.5% and 20%, as well as lecithin concentrations of 0.1%; 0.3%; and 0.5% maintaining a constant content of sugar (25 %, Vanillin (1% that included cacao powder with different pH values: natural (pH 5 and alkalinized (pH 6.5 and pH 8 and water by difference to 100%, generating a total of fifteen treatments to be evaluated, according to the Box-Behnen design for three factors. The treatments underwent satisfaction level tests to establish the general acceptability. The treatment that included cacao powder with a concentration of 17.5 %, pH 6.5 and lecithin concentration of 0.3 % obtained the best levels of acceptability. The software Statgraphics Plus 5.1 was used to obtain the treatment with maximum acceptability that corresponded to cacao powder with pH 6.81, with a concentration of 18.24 % and soy lecithin in 0.28% with a tendency to what was obtained in the satisfaction levels tests. Finally we characterized in a physical-chemistry and microbiological way the optimum formulation as well as evaluated sensitively obtaining an acceptability of 6.17.

  4. Acceptability of using electronic vending machines to deliver oral rapid HIV self-testing kits: a qualitative study.

    Sean D Young

    Full Text Available Rates of unrecognized HIV infection are significantly higher among Latino and Black men who have sex with men (MSM. Policy makers have proposed that HIV self-testing kits and new methods for delivering self-testing could improve testing uptake among minority MSM. This study sought to conduct qualitative assessments with MSM of color to determine the acceptability of using electronic vending machines to dispense HIV self-testing kits.African American and Latino MSM were recruited using a participant pool from an existing HIV prevention trial on Facebook. If participants expressed interest in using a vending machine to receive an HIV self-testing kit, they were emailed a 4-digit personal identification number (PIN code to retrieve the test from the machine. We followed up with those who had tested to assess their willingness to participate in an interview about their experience.Twelve kits were dispensed and 8 interviews were conducted. In general, participants expressed that the vending machine was an acceptable HIV test delivery method due to its novelty and convenience.Acceptability of this delivery model for HIV testing kits was closely associated with three main factors: credibility, confidentiality, and convenience. Future research is needed to address issues, such as user-induced errors and costs, before scaling up the dispensing method.

  5. A proposed rationale and test methodology for establishment of acceptance criteria for vacuum integrity testing of pharmaceutical freeze dryers.

    Hardwick, Lisa M; Nail, Steven L; Jarman, James; Hasler, Kai; Hense, Thomas

    2013-10-01

    A scientific rationale is proposed for the establishment of acceptance criteria for leak rates in pharmaceutical freeze dryers. A method was developed to determine the quantity of air that could leak into any lyophilizer from the outside while still maintaining Class 100/Grade A microbial conditions. A lyophilizing product is assumed most vulnerable to microbial contamination during secondary drying, when mass transfer of water vapor from product to condenser is minimal. Using the void volume of the dryer, calculated from change in internal pressure when a known volume of air is introduced, and the potential maximum bioburden of the leaked air (based on measured values), calculations can determine the allowable leaked volume of air, the flow rate required to admit that volume in a given time frame, and the pressure rise that would result from the leak over a given testing period. For the dryers in this study, using worst-case air quality conditions, it was determined that a leak resulting in a pressure rise of 0.027 mbar over a 30 min period would allow the dryers to remain in secondary drying conditions for 62 h before the established action level of one colony forming unit for each cubic meter of air space would be reached. PMID:23899644

  6. South African physicians’ acceptance of e-prescribing technology: an empirical test of a modified UTAUT model

    Jason Cohen

    2013-07-01

    Full Text Available E-prescribing systems hold promise for improving the quality and efficiency of the scripting process. Yet, the use of the technology has been associated with a number of challenges. The diffusion of e-prescribing into physician practices and the consequent realisation of its potential benefits will depend on whether physicians are willing to accept and engage with the technology. This study draws on the Unified Theory of Acceptance and Use of Technology (UTAUT and recent literature on user trust in technology to develop and test a model of the factors influencing South African physicians’ acceptance of e-prescribing. Data was collected from a sample of 72 physicians. Results indicate a general acceptance of e-prescribing amongst physicians who on average reported strong intentions to use e-prescribing technologies if given the opportunity. PLS analysis revealed that physicians’ performance expectancies and perceptions of facilitating conditions had significant direct effects on acceptance whilst trust and effort expectancy had important indirect effects. Social influence and price value perceptions did not add additional explanatory power. The model explained 63% of the variation in physician acceptance.

  7. Market testing and consumer acceptance of irradiated rice (Oryza sativa indica Linn.)

    Special grade A fragrant rice (Jasmine rice) of 13% moisture content was obtained from a local miller in Bangkok. Low density polyethylene, 29.5 cm in width x 45 cm in length and 200 micron in thickness, was used to pack the rice with a net weight of 5 kg. The irradiated food label was printed on one side of the bag to comply with food control regulations. The color and the ink for marking were tested for gamma radiation compatibility. A total of 800 bags of rice, with a total gross weight of 4,000 kg, were irradiated at a minimum absorbed dose at 0.5 kGy for insect disinfestation. Radiation treatment was carried out using a multi-purpose, carrier type gamma irradiator (Model JS-8900, Serial No. IR-155) located at the Thai Irradiation Center. Irradiated rice was distributed on a weekly basis to food stores in Bangkok and Pathum Thani, as well as to various governmental organizations and interested individuals. The product was sold at 60 bahts per bag (approx. US$ 2.4) to retailers. Various commercial brands of non-irradiated rice of 5 kg size, were available in the market at 52 to 78 bahts per bag (approx. US $ 2.08 to 3.12), depending on quality and brand name. During the distribution, a leaflet of educational information was given to the consumer. A simple questionnaire used in the marketing trial indicated that 72% of the consumers bought irradiated rice because of the good quality of the product based on visual inspection, and 28% of them were willing to try the new product. Most consumers preferred irradiated rice to chemical treatment (fumigation) for insect disinfestation. However, most consumers were not sure if they would like to buy irradiated rice again unless its cooking quality was acceptable. Market testing of irradiated rice in the upper-class market or supermarket was unsuccessful because of limitations in the sale and service conditions. To meet the requirement of the supermarket retailer, irradiated rice had to be supplied on a monthly basis, with

  8. A Randomized Controlled Trial of Acceptance-Based Behavior Therapy and Cognitive Therapy for Test Anxiety: A Pilot Study

    Brown, Lily A.; Forman, Evan M.; Herbert, James D.; Hoffman, Kimberly L.; Yuen, Erica K.; Goetter, Elizabeth M.

    2011-01-01

    Many university students suffer from test anxiety that is severe enough to impair performance. Given mixed efficacy results of previous cognitive-behavior therapy (CBT) trials and a theoretically driven rationale, an acceptance-based behavior therapy (ABBT) approach was compared to traditional CBT (i.e., Beckian cognitive therapy; CT) for the…

  9. Empirical Testing of a Theoretical Extension of the Technology Acceptance Model: An Exploratory Study of Educational Wikis

    Liu, Xun

    2010-01-01

    This study extended the technology acceptance model and empirically tested the new model with wikis, a new type of educational technology. Based on social cognitive theory and the theory of planned behavior, three new variables, wiki self-efficacy, online posting anxiety, and perceived behavioral control, were added to the original technology…

  10. Acceptance test procedure for C-018H, 242-A evaporator/PUREX plant process condensate treatment facility

    This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Electrical/Instrumentation system function as required for this facility. Each company or organization participating in this ATP will designate personnel to assume the responsibilities and duties as defined herein for their respective roles

  11. Acceptability and Feasibility of HIV Self-Testing Among Transgender Women in San Francisco: A Mixed Methods Pilot Study.

    Lippman, Sheri A; Moran, Lissa; Sevelius, Jae; Castillo, Leslie S; Ventura, Angel; Treves-Kagan, Sarah; Buchbinder, Susan

    2016-04-01

    An estimated one in four transgender women (trans women) in the U.S. are infected with HIV. Rates of HIV testing are not commensurate with their risk, necessitating alternative strategies for early detection and care. We explored the feasibility and acceptability of HIV self-testing (HIVST) with 50 HIV-negative adult trans women in San Francisco. Participants received three self-test kits to perform once a month. Acceptability and behavioral surveys were collected as were 11 in-depth interviews (IDIs). Among 50 participants, 44 reported utilizing HIVST at least once; 94 % reported the test easy to use; 93 % said results were easy to read; and 91 % would recommend it to others. Most participants (68 %) preferred HIVST to clinic-based testing, although price was a key barrier to uptake. IDIs revealed a tension between desires for privacy versus support found at testing sites. HIVST for trans women was acceptable and feasible and requires careful consideration of linkage to support services. PMID:26511864

  12. Factors influencing the acceptability of energy policies : A test of VBN theory

    Steg, L; Dreijerink, L; Abrahamse, W

    2005-01-01

    This paper examines factors influencing the acceptability of energy policies aimed to reduce the emission of CO2 by households. More specifically, it is Studied to what extent the value-belief-norm theory of environmentalism (VBN theory; Stern, [(2000). Toward a coherent theory of environmentally si

  13. Commissioning and acceptance testing of Cadplan plus- a 3D treatment planning system

    3D treatment planning systems are finding wide acceptance in the radiotherapy community due to their improved dose calculation accuracy as well as the 3D visualization tools. Cadplan plus, a 3D treatment planning system from Varian, has been commissioned at the Tata Memorial Hospital in accordance to various international guidelines

  14. Acceptance of HIV testing among women attending antenatal care in south-western Uganda: risk factors and reasons for test refusal

    Dahl, Viktor; Mellhammar, Lisa; Bajunirwe, Francis; Björkman, Per

    2008-01-01

    Abstract A problem commonly encountered in programs for prevention of mother-to-child-transmission (PMTCT) of HIV in sub-Saharan Africa is low rates of HIV test acceptance among pregnant women. In this study, we examined risk factors and reasons for HIV test refusal among 432 women attending three antenatal care clinics offering PMTCT in urban and semi-urban parts of the Mbarara district, Uganda. Structured interviews were performed following pre-test counselling. Three-hundre...

  15. In Shop Acceptance Test Report for the SY Farm Annulus Leak Detectors

    The following test report was written for the SY tank farm annulus leak detectors. The test plan used was HNF-4546, Revision 1. The purpose of the test plan was to test the ENRAF series 854 ATG with SPU II card prior to installation. The test plan set various parameters and verifies the gauge and alarms functionality

  16. Healing Our Women for Transgender Women: Adaptation, Acceptability, and Pilot Testing.

    Collier, Kate L; Colarossi, Lisa G; Hazel, Daphne S; Watson, Kim; Wyatt, Gail E

    2015-10-01

    Healing Our Women (HOW) is a group-level HIV risk-reduction intervention developed to address the role of prior sexual victimization in HIV risk and protective behaviors among HIV-positive women of color. This article describes the process of adapting HOW for transgender women of color in New York City in accordance with CDC guidance for the adaptation of efficacious interventions. Twenty-one transgender women were enrolled in a study to evaluate the acceptability and fidelity of the adapted intervention, and to assess HIV knowledge, depressive symptoms, coping, condom use self-efficacy, and condom use via pre- and post-intervention surveys. We found the adapted program to be feasible to implement and acceptable to participants. We also found significant decreases in depressive symptoms and increases in positive coping from pre- to post-intervention, although replication with a larger sample and a control group comparison is needed to determine efficacy with this population. PMID:26485232

  17. International Space Station Environmental Control and Life Support System Acceptance Testing for Node 1 Temperature and Humidity Control Subsystem

    Williams, David E.

    2011-01-01

    The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Storage (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper will provide a summary of the Node 1 ECLS THC subsystem design and a detailed discussion of the ISS ECLS Acceptance Testing methodology utilized for this subsystem.The International Space Station (ISS) Node 1 Environmental Control and Life Support (ECLS) System is comprised of five subsystems: Atmosphere Control and Storage (ACS), Atmosphere Revitalization (AR), Fire Detection and Suppression (FDS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). This paper will provide a summary of the Node 1 ECLS THC subsystem design and a detailed discussion of the ISS ECLS Acceptance Testing methodology utilized for this subsystem.

  18. Acceptability and Feasibility of Sexually Transmitted Infection Testing and Treatment among Pregnant Women in Gaborone, Botswana, 2015

    Adriane Wynn

    2016-01-01

    Full Text Available Introduction. Chlamydia trachomatis (CT, Neisseria gonorrhoeae (NG, and Trichomonas vaginalis (TV are curable sexually transmitted infections (STIs that can cause adverse maternal and birth outcomes. Most countries do not conduct routine testing during antenatal care. We present data on the acceptability and feasibility of testing and treating pregnant women for STIs in an antenatal clinic in Gaborone, Botswana. Materials and Methods. We offered CT, NG, and TV testing using self-collected vaginal swabs to eligible pregnant women. Participants received same-day test results. Those who tested positive were given treatment. Results. Among the 225 women who were eligible and recruited, 200 (89% agreed to participate. The median age of our study sample was 30 years; most were unmarried (77%, with a median gestational age of 27 weeks and a 23% HIV prevalence. All participants received their results with at least 72% (n=143 on the same day. Thirty participants (15% tested positive for an STI, all were treated, and 24 (80% were treated on the same day. Conclusion. The acceptability of STI testing was high, and the intervention was feasible. This study provides support for continued research into STI prevalence, cost-effectiveness, and the association of STIs with adverse maternal and infant outcomes.

  19. 49 CFR 180.511 - Acceptable results of inspections and tests.

    2010-10-01

    ... all product piping, fittings and closures show no indication of leakage. (g) Hydrostatic test. A Class 107 tank car or a riveted tank car successfully passes the hydrostatic test when it shows no leakage... before the next inspection and test interval. (b) Structural integrity inspection and test. A tank...

  20. Human Factors Process Task Analysis: Liquid Oxygen Pump Acceptance Test Procedure at the Advanced Technology Development Center

    Diorio, Kimberly A.; Voska, Ned (Technical Monitor)

    2002-01-01

    This viewgraph presentation provides information on Human Factors Process Failure Modes and Effects Analysis (HF PFMEA). HF PFMEA includes the following 10 steps: Describe mission; Define System; Identify human-machine; List human actions; Identify potential errors; Identify factors that effect error; Determine likelihood of error; Determine potential effects of errors; Evaluate risk; Generate solutions (manage error). The presentation also describes how this analysis was applied to a liquid oxygen pump acceptance test.

  1. Questionnaire design: carry-over effects of overall acceptance question placement and pre-evaluation instructions on overall acceptance scores in central location tests.

    Bastian, Mauresa; Eggett, Dennis L; Jefferies, Laura K

    2015-02-01

    Question placement and usage of pre-evaluation instructions (PEI) in questionnaires for food sensory analysis may bias consumers' scores via carry-over effects. Data from consumer sensory panels previously conducted at a central location, spanning 11 years and covering a broad range of food product categories, were compiled. Overall acceptance (OA) question placement was studied with categories designated as first (the first evaluation question following demographic questions), after nongustation questions (immediately following questions that do not require panelists to taste the product), and later (following all other hedonic and just-about-right [JAR] questions, but occasionally before ranking, open-ended comments, and/or intent to purchase questions). Each panel was categorized as having or not having PEI in the questionnaire; PEI are instructions that appear immediately before the first evaluation question and show panelists all attributes they will evaluate before receiving test samples. Postpanel surveys were administered regarding the self-reported effect of PEI on panelists' evaluation experience. OA scores were analyzed and compared (1) between OA question placement categories and (2) between panels with and without PEI. For most product categories, OA scores tended to be lower when asked later in the questionnaire, suggesting evidence of a carry-over effect. Usage of PEI increased OA scores by 0.10 of a 9-point hedonic scale point, which is not practically significant. Postpanel survey data showed that presence of PEI typically improved the panelists' experience. Using PEI does not appear to introduce a meaningful carry-over effect. PMID:25604650

  2. IMPROVING OF ENERGY AND OTHER INDICATORS OF RECEIVING AND ACCEPTANCE TESTING OF ELECTRIC LOCOMOTIVES TRACTION MOTORS

    P. O. Loza

    2009-03-01

    Full Text Available The methods of determination of equivalent load current in tests of electric locomotive traction engines without forced ventilation with use of the results of qualification test of engines of certain types are offered in the article.

  3. CENRTC Project number-sign 2F3EOA, OCB A-376, acceptance test procedure

    This test procedure provides the steps necessary to verify correct functional operation of controls, annunciators, alarms, protective relays and related systems impacted by CENRTC number-sign 2F3E0A, Microwave Transfer Trip Project, modification work performed under work package 6B-93-00041/M. This procedure separates three tests into separate sections: energization of A-376 duplex panel and circuits; SCADA tests; and A-376 local trip tests

  4. Verification/acceptance test plan/procedure for Acromag calibration system

    Fordham, C.R.

    1994-12-01

    The purpose of this document is to describe and document the test of the Acromag calibration system software. The purpose of this test is to verify that the Acromag Calibration System (ACS) will reliably test the Acromag thermocouple (TC) type input modules and provide a file showing the temperatures at which the modules are tested, the response rom the Acromag station, instrument data, technician data, and date and time of the test. The ACS consists of a thermocouple calibration unit (TCU), a DOS based computer, a hand held resistance temperature detector (RTD) surface probe and connects to a field installed or a bench Acromag unit.

  5. Tank monitor and control system (TMACS) revision 11 acceptance test procedure

    The purpose of this document is to describe tests performed to validate Revision 11 of the Tank Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

  6. Acceptance test report for tank bottom thermocouples on Tank 241-SY-101

    This test report documents testing performed per WHC-SD-WM-ATP-069, Rev. 2. The proper monitoring of the 241-SY-101 Tank Bottom and Side Thermocouples (TBSTC) by the Data Acquisition and Control System (DACS) will be tested to establish continued operability of the system. During this test, an end-to-end verification of all of the sensor circuits associated with the TBSTCs, which provide signals both to the DACS computer system and an installed temporary Data Logger, shall be performed by injecting a signal at the appropriate field terminal and verifying the circuit completely through the system to the computer in the DACS trailer and the computer monitor used to display the output of the Data Logger. Each injected signal will be adjusted for appropriate 'near zero', 'mid range' and 'near full scale' values for the sensor being tested. The TBSTC screen, which provides for operator interface with the TBSTCs, will be utilized to monitor testing at the DACS computers. Testing per this procedure shall be conducted after the installation of the temporary Data Logger for the TBSTCs is complete. The temporary Data Logger will be installed to monitor the temperature readings of 13 of the 26 Tank Bottom Thermocouples in support of SY-101 excavation testing

  7. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid ''P''

    This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

  8. Acceptance Test Procedure for New Pumping Instrumentation and Control Skid Q

    This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis

  9. Acceptability of HIV/AIDS testing among pre-marital couples in Iran (2012

    Jamshid Ayatollahi

    2014-01-01

    Full Text Available Background: Human immunodeficiency virus (HIV/acquired immune deficiency syndrome (AIDS is a lifestyle-related disease. This disease is transmitted through unprotected sex, contaminated needles, infected blood transfusion and from mother to child during pregnancy and delivery. Prevention of infection with HIV, mainly through safe sex and needle exchange programmes is a solution to prevent the spread of the disease. Knowledge about HIV state helps to prevent and subsequently reduce the harm to the later generation. The purpose of this study was to assess the willingness rate of couples referred to the family regulation pre-marital counselling centre for performing HIV test before marriage in Yazd. Patients and Methods: In this descriptive study, a simple random sampling was done among people referred to Akbari clinic. The couples were 1000 men and 1000 women referred to the premarital counselling centre for pre-marital HIV testing in Yazd in the year 2012. They were in situations of pregnancy, delivery or nursing and milking. The data were analyzed using Statistical Package for the Social Sciences (SPSS software and chi-square statistical test. Results: There was a significant statistical difference between the age groups about willingness for HIV testing before marriage (P < 0.001 and also positive comments about HIV testing in asymptomatic individuals (P < 0.001. This study also proved a significant statistical difference between the two gender groups about willingness to marry after HIV positive test of their wives. Conclusion: The willingness rate of couples to undergo HIV testing before marriage was significant. Therefore, HIV testing before marriage as a routine test was suggested.

  10. Shielding requirements on-site loading and acceptance testing on the Leksell gamma knife.

    Maitz, A H; Lunsford, L D; Wu, A; Lindner, G; Flickinger, J C

    1990-02-01

    On August 14, 1987, the first stereotactic radiosurgical procedure using the gamma knife was performed in North America. Located in a self-contained radiosurgical suite in the basement of Presbyterian-University Hospital in Pittsburgh, Pennsylvania. This device uses 201 highly focused beams 60Co for the single-treatment closed-skull irradiation of brain lesions localized by stereotactic techniques (radiosurgery). One hundred and fifty-two patients with intracranial arteriovenous malformations or brain tumors were treated in the first year of operation. The Presbyterian University Hospital of Pittsburgh gamma knife is the first such unit in which the 60Co sources were loaded on-site. This effort required us to solve some difficult and unusual problems encountered during site preparation, delivery, and loading of the unit in a busy hospital setting. The solutions developed enabled installation and use of the gamma knife with minimal disruption of hospital activities while maintaining acceptable levels of exposure to radiation. Environmental surveys performed during the loading of the 201 radioactive sources (total, 219 TBq) confirmed that on-site loading is possible and practical. Our experience in the design, construction, and implementation of the first North American gamma knife supports the practicality and safety of on-site loading and may be of value in the planning and development of future gamma knife installations. PMID:2406231

  11. Shielding requirements on-site loading and acceptance testing on the Leksell gamma knife

    On August 14, 1987, the first stereotactic radiosurgical procedure using the gamma knife was performed in North America. Located in a self-contained radiosurgical suite in the basement of Presbyterian-University Hospital in Pittsburgh, Pennsylvania. This device uses 201 highly focused beams 60Co for the single-treatment closed-skull irradiation of brain lesions localized by stereotactic techniques (radiosurgery). One hundred and fifty-two patients with intracranial arteriovenous malformations or brain tumors were treated in the first year of operation. The Presbyterian University Hospital of Pittsburgh gamma knife is the first such unit in which the 60Co sources were loaded on-site. This effort required us to solve some difficult and unusual problems encountered during site preparation, delivery, and loading of the unit in a busy hospital setting. The solutions developed enabled installation and use of the gamma knife with minimal disruption of hospital activities while maintaining acceptable levels of exposure to radiation. Environmental surveys performed during the loading of the 201 radioactive sources (total, 219 TBq) confirmed that on-site loading is possible and practical. Our experience in the design, construction, and implementation of the first North American gamma knife supports the practicality and safety of on-site loading and may be of value in the planning and development of future gamma knife installations

  12. Is the nacelle mounted anemometer an acceptable option in performance testing?

    Dahlberg, J.A. [FFA, The Aeronautical Research Inst. of Sweden, Bromma (Sweden); Frandsen, S.; Madsen, H.A; Antoniou, I.; Friis Pedersen, T. [Risoe National Lab., Roskilde (Denmark); Hunter, R. [RES, Renewable Energy Systems, Glasgow, Scotland (United Kingdom); Klug, H. [DEWI, Wilhelmshaven (Germany)

    1999-03-01

    Although the nacelle anemometer method has been used for power verification purposes for several years, it is only relatively recently that a full understanding of its limitations has emerged. the technique is totally dependent upon the assumption that the nacelle to free wind speed relationship established for a reference turbine in free air can be applied universally to other turbines. Facts emerged from research projects have shown that this assumption is unjustified. In the present paper facts are presented of which some have not been identified nor presented before. E.g. the effect related to wake conditions is novel as a phenomena and the size of the effect can be considerable. The analysis shows that the total error caused by the effects considered in this paper can, in the worst case reach unacceptable high values, 24%, but by taking precautionary measures the errors can be kept at acceptable low levels, 4%. It is found probable that the future use of nacelle anemometry for power performance verification will be subject to strong restrictions. (au)

  13. Energy policy under power. Alternatives of power generation in the acceptance test

    As illustrated, both the quantitative and qualitative analysis of the evaluations of the examined seven electricity mixes the image of a rejection of nuclear and coal power with or without carbon capture (CCS) with simultaneous support for a renewable energy focus in the center of the transformation of the German systems on the electricity. Energy-political strategies that the electricity produced from renewable sources less space than concede the nuclear power and/or the coal found only in very rare and exceptional cases decidedly on consent. Conversely: if the way in which renewable energy production convincingly by high levels of the electricity mix of ecological power plants are expressed, reduced amounts of nuclear and coal power are accepted as a transitional phenomenon. The finding that actually can get unpopular technologies from the focus of criticism by an appropriate context design, also applies to the CCS technology. This makes it possible to identify some evidence that in the context of nuclear energy-free RE-mixes modern coal-fired power plants with CCS are not be refused per se. However, it should also be noted that CCS will be rejected as a supposedly extra evil often still more vehement than the ''familiar'' nuclear power.

  14. Animal testing, 3R models and regulatory acceptance : Technology transition in a risk-averse context

    Schiffelers, M.J.W.A.

    2016-01-01

    Risk avoidance has resulted in a broad range of regulations to guarantee the safety of products such as pharmaceuticals and chemicals. Many of these regulations rely on animal tests. About 3 million laboratory animals are used annually in Europe to meet such regulatory requirements.Regulatory animal testing raises concerns for scientific, ethical and economic reasons. There are many 3R initiatives to replace, reduce, or refine laboratory animal use. A broad range of 3R models is available and...

  15. Installation, Commissioning and Acceptance Testing of a High Temperature Ultra Nanoindentation Tester

    RUIZ MORENO ANA MARIA; RIPPLINGER Stefan

    2015-01-01

    The Institute for Energy and Transport (IET) of the Joint Research Centre (JRC) has purchased a modular Nanoindentation Test System for testing the physical properties of metallic, ceramic and composite materials at small length scales. The instrument allows the measurements of nanoindentation hardness and Young's modulus, creep, fracture toughness and ductile-to-brittle transition temperature at nano length scales from cryogenic to high temperatures (-150 °C ~ 700 °C). Measurements can be ap...

  16. HIV coping self-efficacy: a key to understanding stigma and HIV test acceptance among incarcerated men in Jamaica.

    Andrinopoulos, Katherine; Kerrigan, Deanna; Figueroa, J Peter; Reese, Richard; Ellen, Jonathan M

    2010-03-01

    Although prisons have been noted as important venues for HIV testing, few studies have explored the factors within this context that may influence HIV test acceptance. Moreover, there is a dearth of research related to HIV and incarcerated populations in middle and low-income countries, where both the burden of HIV and the number of people incarcerated is higher compared to high-income countries. This study explores the relationship between HIV coping self-efficacy, HIV-related stigma, and HIV test acceptance in the largest prisons in Jamaica. A random sample of inmates (n=298) recruited from an HIV testing demonstration project were asked to complete a cross-sectional quantitative survey. Participants who reported high HIV coping self-efficacy (adjusted odds ratio (AOR) 1.86: 95% confidence interval CI 1.24-2.78, p-value=0.003), some perceived risk of HIV (AOR 2.51: 95% (CI) 1.57-4.01, p-value=0.000), and low HIV testing stigma (AOR 1.71: 95% CI 1.05-2.79, p-value=0.032) were more likely to test for HIV. Correlates of HIV coping self-efficacy included external and internal HIV stigma (AOR 1.28: 95% CI 1.25-1.32, p-value=0.000 and AOR 1.76: 95% CI 1.34-2.30, p-value=0.000, respectively), social support (AOR 2.09: 95% CI 1.19-3.68, p-value=0.010), and HIV knowledge (AOR 2.33: 95% CI 1.04-5.22, p-value=0.040). Policy and programs should focus on the interrelationships of these constructs to increase participation in HIV testing in prison. PMID:20390514

  17. Feasibility of the gamma camera acceptance testing procedure introduced by the Swiss Federal Office of public health

    Like in the field of radiology, digital systems are also becoming the standard in the field of nuclear medicine. This offers not only the possibility to process, transmit and archive data from patients more easily but also to introduce quantitative measurements for quality controls. In this framework, standards concerning the qualification of gamma camera systems have been updated and appeared to be useful to set legal requirements, in spite of the fact, that this is not their goals. The aim of this study was first to choose a set of tests described in standards to define measurements to be performed at the acceptance of the systems and after the regular maintenance (at least once every six months). Reference values are then established to control the stability of the system. To verify the feasibility, from a technical and a time requirements points of view, the tests proposed for the quality assurance programme have been applied on three gamma camera systems. The results of this study show that new requirements concerning the quality assurance of gamma camera of the Swiss Federal Office of Public Health based on international standards required to slightly modify some procedures to reduce the time necessary for the acceptance and status tests. (authors)

  18. Feasibility of the gamma camera acceptance testing procedure introduced by the Swiss Federal Office of public health

    Baechler, S.; Bochud, F.; Verdun, F.R. [University Institute for Radiation Physics, Lausanne (Switzerland); Corminboeuf, F. [Klinik and Poliklinik fur Nuklearmedizin der Universitat, Inselspital, Bern (Switzerland); Linder, R.; Trueb, Ph. [Swiss Federal Office of Public Health, Bern (Switzerland); Malterre, J.; Bischof Delaloye, A. [University Hospital of Lausanne (CHUV), Nuclear Medicine Dept., Lausanne (Switzerland)

    2006-07-01

    Like in the field of radiology, digital systems are also becoming the standard in the field of nuclear medicine. This offers not only the possibility to process, transmit and archive data from patients more easily but also to introduce quantitative measurements for quality controls. In this framework, standards concerning the qualification of gamma camera systems have been updated and appeared to be useful to set legal requirements, in spite of the fact, that this is not their goals. The aim of this study was first to choose a set of tests described in standards to define measurements to be performed at the acceptance of the systems and after the regular maintenance (at least once every six months). Reference values are then established to control the stability of the system. To verify the feasibility, from a technical and a time requirements points of view, the tests proposed for the quality assurance programme have been applied on three gamma camera systems. The results of this study show that new requirements concerning the quality assurance of gamma camera of the Swiss Federal Office of Public Health based on international standards required to slightly modify some procedures to reduce the time necessary for the acceptance and status tests. (authors)

  19. The adaptive secondary mirror for the Large Binocular Telescope: optical acceptance test and preliminary on-sky commissioning results

    Riccardi, Armando; Xompero, Marco; Briguglio, Runa; Quirós-Pacheco, Fernando; Busoni, Lorenzo; Fini, Luca; Puglisi, Alfio; Esposito, Simone; Arcidiacono, Carmelo; Pinna, Enrico; Ranfagni, Piero; Salinari, Piero; Brusa, Guido; Demers, Richard; Biasi, Roberto; Gallieni, Daniele

    2010-07-01

    The Large Binocular Telescope (LBT) has two adaptive secondary mirrors based on 672 voice-coil force actuators. The shape of the mirror is controlled using internal metrology based on co-located capacitive sensors. The first mirror unit is currently mounted on LBT for on-sky commissioning as part of the First Light Adaptive Optics System (FLAO). During spring-time 2009 the optical acceptance test was performed using the 14-m optical test tower at the Osservatorio Astrofisico di Arcetri (INAF) showing the capability of flattening the shell at the level of 14nm rms residual surface error. This paper reports the optical layout, calibration procedures and results of the optical acceptance test. Moreover we report the first results obtained during the early runs of FLAO commissioning showing the ability of the mirror to compensate for atmospheric turbulence with extremely high Strehl ratio values (better than 80% in H-band) as permitted by the largest number of correcting degrees of freedom currently available on-sky for astronomical telescopes.

  20. Client characteristics and acceptability of a home-based HIV counselling and testing intervention in rural South Africa

    Naik Reshma

    2012-09-01

    Full Text Available Abstract Background HIV counselling and testing (HCT is a critical gateway for addressing HIV prevention and linking people to treatment, care, and support. Since national testing rates are often less than optimal, there is growing interest in expanding testing coverage through the implementation of innovative models such as home-based HIV counselling and testing (HBHCT. With the aim of informing scale up, this paper discusses client characteristics and acceptability of an HBHCT intervention implemented in rural South Africa. Methods Trained lay counsellors offered door-to-door rapid HIV testing in a rural sub-district of KwaZulu-Natal, South Africa. Household and client data were captured on cellular phones and transmitted to a web-based data management system. Descriptive analysis was undertaken to examine client characteristics, testing history, HBHCT uptake, and reasons for refusal. Chi-square tests were performed to assess the association between client characteristics and uptake. Results Lay counsellors visited 3,328 households and tested 75% (5,086 of the 6,757 people met. The majority of testers (73.7% were female, and 57% had never previously tested. With regard to marital status, 1,916 (37.7%, 2,123 (41.7%, and 818 (16.1% were single, married, and widowed, respectively. Testers ranged in age from 14 to 98 years, with a median of 37 years. Two hundred and twenty-nine couples received couples counselling and testing; 87.8%, 4.8%, and 7.4% were concordant negative, concordant positive, and discordant, respectively. There were significant differences in characteristics between testers and non-testers as well as between male and female testers. The most common reasons for not testing were: not being ready/feeling scared/needing to think about it (34.1%; knowing his/her status (22.6%, being HIV-positive (18.5%, and not feeling at risk of having or acquiring HIV (10.1%. The distribution of reasons for refusal differed significantly by gender

  1. CENRTC Project No. 2F3EOA, OCB A-372, acceptance test procedure

    Akerson, A.W.

    1995-01-01

    This test procedure provides the steps necessary to verify correct functional operation of controls, annunciators, alarms, protective relays and related systems impacted by CENRTC No. 2F3EOA, Microwave Transfer Trip Project, modification work performed under work package 6B-93-00038/M (CENRTC 2F3EOA MWTT OCB A-372 PACKAGE).

  2. Hanford immobilized LAW product acceptance: Initial Tanks Focus Area testing data package

    JD Vienna; A Jiricka; BP McGrail; BM Jorgensen; DE Smith; BR Allen; JC Marra; DK Peeler; KG Brown; IA Reamer; WL Ebert

    2000-03-08

    The Hanford Site's mission has been to produce nuclear materials for the US Department of Energy (DOE) and its predecessors. A large inventory of radioactive and mixed waste, largely generated during plutonium production, exists in 177 underground single- and double-shell tanks. These wastes are to be retrieved and separated into low-activity waste (LAW) and high-level waste (HLW) fractions. The total volume of LAW requiring immobilization will include the LAW separated from the tank waste, as well as new wastes generated by the retrieval, pretreatment, and immobilization processes. Per the Tri-Party Agreement (1994), both the LAW and HLW will be vitrified. It has been estimated that vitrification of the LAW waste will result in over 500,000 metric tons or 200,000 m{sup 3} of immobilized LAW (ILAW) glass. The ILAW glass is to be disposed of onsite in a near-surface burial facility. It must be demonstrated that the disposal system will adequately retain the radionuclides and prevent contamination of the surrounding environment. This report describes a study of the impacts of systematic glass-composition variation on the responses from accelerated laboratory corrosion tests of representative LAW glasses. A combination of two tests, the product consistency test and vapor-hydration test, is being used to give indictations of the relative rate at which a glass could be expected to corrode in the burial scenario.

  3. 40 CFR 86.1830-01 - Acceptance of vehicles for emission testing.

    2010-07-01

    ... emission data vehicles. (1) All EDV's shall have at least the minimum number of miles accumulated to... selected for emission data testing may not be used as the EDV for that configuration. Vehicles from outside... reconfigure EDV's under the provisions of paragraph (c)(2) of this section must be appropriately aged...

  4. Acceptance testing report of Eductor System to be installed in the 105 K Basins

    The Spent Nuclear Fuel (SNF) Project Engineering Support group cold-tested the Eductor System a 15 horsepower multi-stage centrifugal pump manufactured by the Grunfos Corporation with the housing manufactured and sold with the pump by the Tri-Nuclear Corporation and a 3-inch diameter water jet eductor manufactured by the Fox Valve Corporation. The Eductor System was tested to gather and document information to optimize sludge retrieval operations for use in the 105 K Basins. The cold-testing took place during February 12 through February 29, 1996 in the 305 Cold Test Facility basin located in the 300 area. The pump, utilized in conjunction with the eductor, makes up the core of the Eductor System. The pumping unit consists of a 15 hp stainless steel multi-stage centrifugal Grunfos pump which is seated in a stainless steel fabricated housing. Two baskets or filter elements make up part of the housing on the suction side of the pump. The pump can be used independent of the housing but the housing has two identified purposes. The first use is to stabilize the centrifugal pump and give the pneumatic valves and pump discharge piping a solid platform so the Eductor System can be more easily mobilized within the basin as one unit. The second use for the housing presents the option to utilize the suction-side filters for capturing larger fuel pieces after the smaller fines have been removed

  5. CENRTC Project No. 2F3EOA, OCB A-372, acceptance test procedure

    This test procedure provides the steps necessary to verify correct functional operation of controls, annunciators, alarms, protective relays and related systems impacted by CENRTC No. 2F3EOA, Microwave Transfer Trip Project, modification work performed under work package 6B-93-00038/M (CENRTC 2F3EOA MWTT OCB A-372 PACKAGE)

  6. Animal testing, 3R models and regulatory acceptance : Technology transition in a risk-averse context

    Schiffelers, M.J.W.A.

    2016-01-01

    Risk avoidance has resulted in a broad range of regulations to guarantee the safety of products such as pharmaceuticals and chemicals. Many of these regulations rely on animal tests. About 3 million laboratory animals are used annually in Europe to meet such regulatory requirements.Regulatory animal

  7. Hanford immobilized LAW product acceptance: Initial Tanks Focus Area testing data package

    The Hanford Site's mission has been to produce nuclear materials for the US Department of Energy (DOE) and its predecessors. A large inventory of radioactive and mixed waste, largely generated during plutonium production, exists in 177 underground single- and double-shell tanks. These wastes are to be retrieved and separated into low-activity waste (LAW) and high-level waste (HLW) fractions. The total volume of LAW requiring immobilization will include the LAW separated from the tank waste, as well as new wastes generated by the retrieval, pretreatment, and immobilization processes. Per the Tri-Party Agreement (1994), both the LAW and HLW will be vitrified. It has been estimated that vitrification of the LAW waste will result in over 500,000 metric tons or 200,000 m3 of immobilized LAW (ILAW) glass. The ILAW glass is to be disposed of onsite in a near-surface burial facility. It must be demonstrated that the disposal system will adequately retain the radionuclides and prevent contamination of the surrounding environment. This report describes a study of the impacts of systematic glass-composition variation on the responses from accelerated laboratory corrosion tests of representative LAW glasses. A combination of two tests, the product consistency test and vapor-hydration test, is being used to give indictations of the relative rate at which a glass could be expected to corrode in the burial scenario

  8. 105KE Basin Area Radiation Monitor System (ARMS) Acceptance Test Procedure

    KINKEL, C.C.

    1999-12-14

    This procedure is intended for the Area Radiation Monitoring System, ARMS, that is replacing the existing Programmable Input-Output Processing System, PIOPS, radiation monitoring system in the 105KE basin. The new system will be referred to as the 105KE ARMS, 105KE Area Radiation Monitoring System. This ATP will ensure calibration integrity of the 105KE radiation detector loops. Also, this ATP will test and document the display, printing, alarm output, alarm acknowledgement, upscale check, and security functions. This ATP test is to be performed after completion of the 105KE ARMS installation. The alarm outputs of the 105KE ARMS will be connected to the basin detector alarms, basin annunciator system, and security Alarm Monitoring System, AMS, located in the 200 area Central Alarm Station (CAS).

  9. 105KE Basin Area Radiation Monitor System (ARMS) Acceptance Test Procedure

    Kinkel, C C

    1999-01-01

    This procedure is intended for the Area Radiation Monitoring System, ARMS, that is replacing the existing Programmable Input-Output Processing System, PIOPS, radiation monitoring system in the 105KE basin. The new system will be referred to as the 105KE ARMS, 105KE Area Radiation Monitoring System. This ATP will ensure calibration integrity of the 105KE radiation detector loops. Also, this ATP will test and document the display, printing, alarm output, alarm acknowledgement, upscale check, and security functions. This ATP test is to be performed after completion of the 105KE ARMS installation. The alarm outputs of the 105KE ARMS will be connected to the basin detector alarms, basin annunciator system, and security Alarm Monitoring System, AMS, located in the 200 area Central Alarm Station (CAS).

  10. Acceptance Testing of a Satellite SCADA Photovoltaic-Diesel Hybrid System

    Kalu, A.; Emrich, C.; Ventre, G.; Wilson, W.; Acosta, Roberto (Technical Monitor)

    2000-01-01

    Satellite Supervisory Control and Data Acquisition (SCADA) of a Photovoltaic (PV)/diesel hybrid system was tested using NASA's Advanced Communication Technology Satellite (ACTS) and Ultra Small Aperture Terminal (USAT) ground stations. The setup consisted of a custom-designed PV/diesel hybrid system, located at the Florida Solar Energy Center (FSEC), which was controlled and monitored at a "remote" hub via Ka-band satellite link connecting two 1/4 Watt USATs in a SCADA arrangement. The robustness of the communications link was tested for remote monitoring of the health and performance of a PV/diesel hybrid system, and for investigating load control and battery charging strategies to maximize battery capacity and lifetime, and minimize loss of critical load probability. Baseline hardware performance test results demonstrated that continuous two-second data transfers can be accomplished under clear sky conditions with an error rate of less than 1%. The delay introduced by the satellite (1/4 sec) was transparent to synchronization of satellite modem as well as to the PV/diesel-hybrid computer. End-to-end communications link recovery times were less than 36 seconds for loss of power and less than one second for loss of link. The system recovered by resuming operation without any manual intervention, which is important since the 4 dB margin is not sufficient to prevent loss of the satellite link during moderate to heavy rain. Hybrid operations during loss of communications link continued seamlessly but real-time monitoring was interrupted. For this sub-tropical region, the estimated amount of time that the signal fade will exceed the 4 dB margin is about 10%. These results suggest that data rates of 4800 bps and a link margin of 4 dB with a 1/4 Watt transmitter are sufficient for end-to-end operation in this SCADA application.

  11. Fort St. Vrain helium circulator auxiliary systems: dynamic performance evaluation and acceptance tests

    The purpose of the tests described is to show that the dynamic performance of the Fort St. Vrain helium circulator auxiliary systems satisfies all the guidelines and criteria established and agreed to by Public Service Company of Colorado (PSC), Proto-Power, and General Atomic Company (GA). Specifically, it is shown that transfers to and from backup bearing water and helium purification system transients do not cause any circulator trips. Furthermore, at PSC's request, in an effort to resolve any NFSC questions concerning these systems, the satisfactory repeatability of their dynamic performance is shown beyond any doubt.

  12. Human Factors Process Task Analysis Liquid Oxygen Pump Acceptance Test Procedure for the Advanced Technology Development Center

    Diorio, Kimberly A.

    2002-01-01

    A process task analysis effort was undertaken by Dynacs Inc. commencing in June 2002 under contract from NASA YA-D6. Funding was provided through NASA's Ames Research Center (ARC), Code M/HQ, and Industrial Engineering and Safety (IES). The John F. Kennedy Space Center (KSC) Engineering Development Contract (EDC) Task Order was 5SMA768. The scope of the effort was to conduct a Human Factors Process Failure Modes and Effects Analysis (HF PFMEA) of a hazardous activity and provide recommendations to eliminate or reduce the effects of errors caused by human factors. The Liquid Oxygen (LOX) Pump Acceptance Test Procedure (ATP) was selected for this analysis. The HF PFMEA table (see appendix A) provides an analysis of six major categories evaluated for this study. These categories include Personnel Certification, Test Procedure Format, Test Procedure Safety Controls, Test Article Data, Instrumentation, and Voice Communication. For each specific requirement listed in appendix A, the following topics were addressed: Requirement, Potential Human Error, Performance-Shaping Factors, Potential Effects of the Error, Barriers and Controls, Risk Priority Numbers, and Recommended Actions. This report summarizes findings and gives recommendations as determined by the data contained in appendix A. It also includes a discussion of technology barriers and challenges to performing task analyses, as well as lessons learned. The HF PFMEA table in appendix A recommends the use of accepted and required safety criteria in order to reduce the risk of human error. The items with the highest risk priority numbers should receive the greatest amount of consideration. Implementation of the recommendations will result in a safer operation for all personnel.

  13. Storage, transportation, test marketing and consumer acceptance of irradiated potatoes, onions, garlic and fruit

    The Shanghai Irradiation Center irradiated 830 tonnes of garlic 395 tonnes of potatoes 620 tonnes of onions and 50 tonnes of apples from 1990 to 1993 for test marketing. A consumer trial on irradiated apples was conducted. The results showed that 90% of consumers liked irradiated fruit and would be willing to buy them again. SIC established technological standards for the irradiation of garlic, potatoes and onions based on the codes of good irradiation practices recommended by the International Consultative Group on Food Irradiation. These standards were followed during the conduct of the research studies reported in this paper. A cost-benefit analysis of irradiated apples and garlic was performed. It was observed that irradiated apples would provide a profit of 52% and irradiated garlic 100% compared to unirradiated products. Data from an economic benefits study showed that products requiring a low absorbed dose have a higher profit margin. Therefore, the irradiation of garlic, potatoes and apples would be more profitable than radiation treatment of medical supplies and industrial products. (author). 7 refs, 3 figs, 10 tabs

  14. HIV testing in non-traditional settings--the HINTS study: a multi-centre observational study of feasibility and acceptability.

    Michael Rayment

    Full Text Available BACKGROUND: UK guidelines recommend routine HIV testing in healthcare settings if the local diagnosed HIV prevalence >2/1000 persons. This prospective study assessed the feasibility and acceptability, to patients and staff, of routinely offering HIV tests in four settings: Emergency Department, Acute Care Unit, Dermatology Outpatients and Primary Care. Modelling suggested the estimated prevalence of undiagnosed HIV infection in attendees would exceed 1/1000 persons. The prevalence identified prospectively was not a primary outcome. METHODS: Permanent staff completed questionnaires assessing attitudes towards routine HIV testing in their workplace before testing began. Subsequently, over a three-month period, patients aged 16-65 were offered an HIV test by study staff. Demographics, uptake, results, and departmental activity were collected. Subsets of patients completed questionnaires. Analyses were conducted to identify factors associated with test uptake. FINDINGS: Questionnaires were received from 144 staff. 96% supported the expansion of HIV testing, but only 54% stated that they would feel comfortable delivering testing themselves, with 72% identifying a need for training. Of 6194 patients offered a test, 4105 (66·8% accepted (61·8-75·4% across sites. Eight individuals were diagnosed with HIV (0-10/1000 across sites and all transferred to care. Younger people, and males, were more likely to accept an HIV test. No significant associations were found between uptake and ethnicity, or clinical site. Questionnaires were returned from 1003 patients. The offer of an HIV test was acceptable to 92%. Of respondents, individuals who had never tested for HIV before were more likely to accept a test, but no association was found between test uptake and sexual orientation. CONCLUSIONS: HIV testing in these settings is acceptable, and operationally feasible. The strategy successfully identified, and transferred to care, HIV-positive individuals. However

  15. Compliance with the Nevada Test Site's waste acceptance criteria for vitrified cesium-loaded crystalline silicotitanate (CST)

    Oak Ridge National Laboratory (ORNL) and Savannah River Technology Center (SRTC) are involved in a joint project for immobilization of radionuclides from the Melton Valley Storage Tanks (MVST) at Oak Ridge (OR). The supernate from Tank W-29 of the MVST will be treated by passage through a crystalline silicotitanate (CST) ion exchange medium. The CST was designed to sorb cesium, the primary radio nuclide (Cs-137) in the supernate of MVST's. A smaller amount of strontium (Sr-90) will also be sorbed. This demonstration will be performed by ORNL. One column volume of cesium-loaded CST (∼10 gallons or 38 liters) will then be shipped to SRTC where it will be mixed with glass formers and fed as an aqueous slurry to a joule-heated melter within the SRTC Shielded Cells. A borosilicate glass formulation which will incorporate the CST has been developed as part oft SRTC's role in this project. The molten glass (∼1150 degrees C) will be poured into 500 ml stainless steel beakers which in turn will be placed in 30 gallon drums for disposal. An import ampersand f part of this project is to demonstrate that the glass waste form produced will meet the Waste Acceptance Criteria (WAC) for disposal at the Nevada Test Site (NTS). If vitrification of the cesium-loaded CST is implemented as the immobilization method for all of the MVST supernate, then it is essential to demonstrate that the waste can be disposed of at an acceptable disposal facility. NTS accepts low-level radioactive waste as long as it is not TRU and not hazardous. This paper documents the efforts in the development stage of this work to integrate the requirements of NTS into the formulation and processing efforts. This work is funded by the Tank Focus Area with additional funding for ORNL provided by EM-30 at OR

  16. Results of the Updated NASA Kennedy Space Center 50-MHz Doppler Radar Wind Profiler Operational Acceptance Test

    Barbre', Robert E., Jr.; Deker, Ryan K.; Leahy, Frank B.; Huddleston, Lisa

    2016-01-01

    We present here the methodology and results of the Operational Acceptance Test (OAT) performed on the new Kennedy Space Center (KSC) 50-MHz Doppler Radar Wind Profiler (DRWP). On day-of-launch (DOL), space launch vehicle operators have used data from the DRWP to invalidate winds in prelaunch loads and trajectory assessments due to the DRWP's capability to quickly identify changes in the wind profile within a rapidly-changing wind environment. The previous DRWP has been replaced with a completely new system, which needs to undergo certification testing before being accepted for use in range operations. The new DRWP replaces the previous three-beam system made of coaxial cables and a copper wire ground plane with a four-beam system that uses Yagi antennae with enhanced beam steering capability. In addition, the new system contains updated user interface software while maintaining the same general capability as the previous system. The new DRWP continues to use the Median Filter First Guess (MFFG) algorithm to generate a wind profile from Doppler spectra at each range gate. DeTect (2015) contains further details on the upgrade. The OAT is a short-term test designed so that end users can utilize the new DRWP in a similar manner to the previous DRWP during mission operations at the Eastern Range in the midst of a long-term certification process. This paper describes the Marshall Space Flight Center Natural Environments Branch's (MSFC NE's) analyses to verify the quality and accuracy of the DRWP's meteorological data output as compared to the previous DRWP. Ultimately, each launch vehicle program has the responsibility to certify the system for their own use.

  17. Flaw acceptance criteria taking into consideration the NDT: radiographic and ultrasonic testing. Analysis through the fracture mechanics methods

    The present study compares and evaluates the flaw acceptance criteria of the non-destructive inspections meeting European Community standards, through the application of the fracture mechanics methods that were determined and verified by the previous activity. Some choices were made; these, however, do not change the general validity of the conclusions. Shaved full-penetration butt welds of Class 1 components making up the primary circuit were considered and the following parameters varied: standards: French, German, Italian (ASME III) and UK; material: AISI 316 and low alloy steel A 533; base material and weld metal; temperature: RT, 370 deg C for the austenitic and 260 deg C for the ferritic steel; ultrasonic and radiographic methods; defect position: surface and internal; stress condition: situations with different primary and secondary stresses. From a preliminary examination of this study it is evident that the large quantity of results available and the abundance of information contained therein make a simple and exhaustive synthesis difficult. In fact, different analyses are possible and we have, therefore, limited the research to activities to perform a comparison and a general evaluation of the acceptance criteria of the non-destructive testing. (authors). 57 refs., 25 figs., 11 tabs

  18. Proton injector acceptance tests for a Dielectric Wall Accelerator (DWA):characterisation of Advanced Injection System of Light Ions (AISLI)

    Peng, S.X., E-mail: sxpeng@pku.edu.cn; Ren, H.T.; Xu, Y.; Zhang, T.; Zhao, J.; Zhang, A.L.; Guo, Z.Y.; Chen, J.E.

    2014-11-01

    To demonstrate the acceleration capability of a Dielectric Wall Accelerator (DWA), a proton injector has been developed at Peking University (PKU). It is composed of a compact permanent magnet 2.45 GHz Electron Cyclotron Resonance Ion Source (PKU PMECRIS) associated with a LEBT of two electrostatic Einzel lenses [1]. This injector is named as Advanced Injector System of Light Ions (AISLI). The acceptance tests have been performed with a 40 keV–55 mA hydrogen beam successfully passing through a ϕ 10 mm aperture diaphragm. This diaphragm is located 200 mm downstream the plasma emission hole at the location of the future DWA entrance flange. The beam rms emittance reached about 0.10 π mm mrad in pulsed mode. This article describes the AISLI experimental setup, the measurement principle and the obtained beam characteristics.

  19. Proton injector acceptance tests for a Dielectric Wall Accelerator (DWA):characterisation of Advanced Injection System of Light Ions (AISLI)

    To demonstrate the acceleration capability of a Dielectric Wall Accelerator (DWA), a proton injector has been developed at Peking University (PKU). It is composed of a compact permanent magnet 2.45 GHz Electron Cyclotron Resonance Ion Source (PKU PMECRIS) associated with a LEBT of two electrostatic Einzel lenses [1]. This injector is named as Advanced Injector System of Light Ions (AISLI). The acceptance tests have been performed with a 40 keV–55 mA hydrogen beam successfully passing through a ϕ 10 mm aperture diaphragm. This diaphragm is located 200 mm downstream the plasma emission hole at the location of the future DWA entrance flange. The beam rms emittance reached about 0.10 π mm mrad in pulsed mode. This article describes the AISLI experimental setup, the measurement principle and the obtained beam characteristics

  20. First light AO (FLAO) system for LBT: final integration, acceptance test in Europe, and preliminary on-sky commissioning results

    Esposito, Simone; Riccardi, Armando; Fini, Luca; Puglisi, Alfio T.; Pinna, Enrico; Xompero, Marco; Briguglio, Runa; Quirós-Pacheco, Fernando; Stefanini, Paolo; Guerra, Juan C.; Busoni, Lorenzo; Tozzi, Andrea; Pieralli, Francesca; Agapito, Guido; Brusa-Zappellini, Guido; Demers, Richard; Brynnel, Joar; Arcidiacono, Carmelo; Salinari, Piero

    2010-07-01

    In this paper we present the laboratory characterization and performance evaluation of the First Light Adaptive Optics (FLAO) the Natural Guide Star adaptive optics system for the Large Binocular Telescope (LBT). The system uses an adaptive secondary mirror with 672 actuators and a pyramid wavefront sensor with adjustable sampling of the telescope pupil from 30×30 down to 4×4 subapertures. The system was fully assembled in the Arcetri Observatory laboratories, passing the acceptance test in December 2009. The performance measured during the test were closed to goal specifications for all star magnitudes. In particular FLAO obtained 83% Strehl Ratio (SR) in the bright end (8.5 magnitudes star in R band) using H band filter and correcting 495 modes with 30×30 subapertures sampling. In the faint end (16.4 magnitude) a 5.0% SR correcting 36 modes with 7×7 subapertures was measured. The seeing conditions for these tests were 0.8" (r0 = 0.14m @ 550 nm) and an average wind speed of 15m/s. The results at other seeing conditions up to 1.5" are also presented. The system has been shipped to the LBT site, and the commissioning is taking place since March to December 2010. A few on sky results are presented.

  1. The Romanian experience on testing and quality acceptance criteria of packages used for transportation and storage of radioactive wastes

    The transport of radioactive wastes generated by nuclear facilities from non-power applications (research institutes, hospitals, nuclear fuel work) in Romania is one of the important subprograms of Romanian Waste Management Programme and the overall aim is to promote a safe transport of radioactive materials in Romania. After emphasizing the importance of the packaging tests in ensuring that the required safety features built into the design of packages comply with the Romanian Nuclear Regulatory Body - National Commission for Nuclear Activities Control (NCNAC) requirements and to IAEA's Regulations, the paper presents the type and production testing for type A packages (containers) which have been developed within Institute for Nuclear Research (INR) Pitesti. The paper describes and contains illustrations showing the various tests conducted on the prototype package and how they relate to normal conditions and minor mishaps during transport. Quality assurance and quality acceptance criteria as well as measures taken in order to meet technical specification provided by the design are also presented and commented. The paper concludes that the justification for containment, based on the use of freight container and the pessimistic assessment of potential inhalation doses to those persons involved with the packaging and transport of radwastes, supports the containers as being suitable for classification as an Industrial Type 3 (IP-3). (author)

  2. Acceptability and feasibility of using established geosocial and sexual networking mobile applications to promote HIV and STD testing among men who have sex with men

    Sun, Christina J.; Stowers, Jason; Miller, Cindy; BACHMANN, LAURA H.; Rhodes, Scott D.

    2015-01-01

    This study is the first published multi-app study, of which we are aware, to evaluate both the acceptability and feasibility of providing sexual health information and HIV/STD testing referrals via established geosocial and sexual networking apps for MSM. Data were collected using an online survey and through four apps (A4A Radar, Grindr, Jack’d, and Scruff). Two-thirds (64%) found apps to be an acceptable source for sexual health information. MSM who found apps as acceptable were more likely...

  3. Responsible technology acceptance

    Toft, Madeleine Broman; Schuitema, Geertje; Thøgersen, John

    2014-01-01

    on private consumers’ acceptance of having Smart Grid technology installed in their home. We analyse acceptance in a combined framework of the Technology Acceptance Model and the Norm Activation Model. We propose that individuals are only likely to accept Smart Grid technology if they assess...... usefulness in terms of a positive impact for society and the environment. Therefore, we expect that Smart Grid technology acceptance can be better explained when the well-known technology acceptance parameters included in the Technology Acceptance Model are supplemented by moral norms as suggested by the...... Norm Activation Model. We tested this proposition by means of an online survey of Danish (N=323), Norwegian (N=303) and Swiss (N=324) private consumers. The study confirms that adding personal norms to the independent variables of the Technology Acceptance Model leads to a significant increase in the...

  4. Gamma-ray spectrometry combined with acceptable knowledge (GSAK). A technique for characterization of certain remote-handled transuranic (RH-TRU) wastes. Part 2. Testing and results

    Gamma-ray spectrometry combined with acceptable knowledge (GSAK) is a technique for the characterization of certain remote-handled transuranic (RH-TRU) wastes. GSAK uses gamma-ray spectrometry to quantify a portion of the fission product inventory of RH-TRU wastes. These fission product results are then coupled with calculated inventories derived from acceptable process knowledge to characterize the radionuclide content of the assayed wastes. GSAK has been evaluated and tested through several test exercises. These tests and their results are described; while the former paper in this issue presents the methodology, equipment and techniques. (author)

  5. The T-1 Two-way Radio-Frequency Seal (TRFS) and acceptance testing for IAEA routine use

    Full text: The Two-way Radio Frequency Seal (TRFS) or T-1 Electronic Sensor Platform (T-1 ESP), which are the International Atomic Energy Agency (IAEA) and Sandia National Laboratories (SNL) designators, respectively, is an electronic sensor platform with two-way radio-frequency (rf) communications. The primary sensor is an active fiber optic loop seal; the ESP accommodates other internal and external, analog and digital output sensors. An embedded data authentication algorithm and a tamper resistant housing including active tamper sensors provide sensor-to- review end-to-end data security. A stainless steel housing provides limited radiation protection. A Data Review Station (DRS) provides an inspector's interface that is part of an integrated Material Monitoring System (MMS). Either the MMS/DRS or a separate portable computer is used to configure the TRFS, including authentication key installation. The T-1 TRFS is currently in the final stages of IAEA evaluation and approval for routine use. Environmental testing has been performed by Euratom's Joint Research Center in Ispra, Italy (JRC Ispra). Canada's Communications Security Establishment (CSE) and the UK's Communications-Electronics Security Group (CESG) have completed independent third-party vulnerability assessments. The remaining steps include modification of the MMS/DRS inspector's review software interface to satisfy IAEA requirements and IAEA testing and acceptance of the DRS. The planned first major operational installation of T-1 TRFS is for joint domestic and IAEA use at the U.S. Department of Energy's (DOE) Savannah River Site (SRS) K-Area Material Storage (KAMS) in Aiken, South Carolina, USA. The T-1 domestic material surveillance system is already installed and approved for operational use by the Westinghouse Savannah River Company (WSRC) and DOE. The IAEA T-1 TRFS KAMS implementation awaits a joint agreement regarding KAMS by the U.S. Government (USG) and the IAEA, and IAEA approval and acceptance

  6. Field studies to determine acceptable levels of contamination at former UK nuclear testing sites, Maralinga and Emu in Australia

    The Maralinga and Emu regions of South Australia were used between 1953 and 1961 for the UK nuclear weapon development program. Two types of trials were conducted - the major trials involved the detonation of fission weapons and the minor trials dealt with weapon design and operational safety. In 1986, as a result of the findings of the Royal Commission on Nuclear Testing in Australia, the UK and Australian governments agreed to set up a Technical Assessment Group (TAG) with one American, two Australian and two British members to review the Maralinga-Emu situation. TAG was to advise on a series of clean-up options and their associated costs and examine land-use options ranging from unrestricted use by the traditional Aboriginal land owners to options involving various degrees of administrative and physical control. In its interim report, presented in May 1986, TAG observed that the existing data base was inadequate and suggested a series of field and laboratory studies that would partly correct this situation. Six of these studies were concerned with redefining the existing levels of contamination and establishing acceptable levels of contamination for a range of land-use options. This paper discusses the rationale, organisational support, scope and experimental protocol adopted for each of the six studies

  7. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from equipment suppliers of manufacturers in new and existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing quality status of the equipment. A working group has developed guidelines for these acceptance tests. Items to be measured are reported and proposed limiting values and their tolerances are discussed. (author)

  8. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from the equipment suppliers or manufacturers in new and also existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing the quality status of the equipment. A working group has developed guidelines for these acceptance tests. The items to be measured are reported and the proposed limiting values and their tolerances are discussed. (author)

  9. Project W-314 acceptance test report HNF-4651 for HNF-4650 SN-268 encasement leak detection ANA-WT-LDSTA-335 for project W-314

    The purpose of the test was to verify that the AN Tank Farm Encasement Leak Detector components are functionally integrated and operate in accordance with engineering design specifications The Acceptance Test Procedure HNF-4650, SN-268 Encasement Leak Detection ANA-W-LDSTA-335, was conducted between 22 June and 01 July 1999 at the 200E AN Tank Farm. The test has been completed with no open test exceptions The test was conducted prior to final engineering ''as built'' activities being completed this had no impact on the procedure or test results. All components, identified in the procedure, were found to be labeled and identified as written in the procedure

  10. Acceptability and feasibility of using established geosocial and sexual networking mobile applications to promote HIV and STD testing among men who have sex with men.

    Sun, Christina J; Stowers, Jason; Miller, Cindy; Bachmann, Laura H; Rhodes, Scott D

    2015-03-01

    This study is the first published multi-app study, of which we are aware, to evaluate both the acceptability and feasibility of providing sexual health information and HIV/STD testing referrals via established geosocial and sexual networking apps for MSM. Data were collected using an online survey and through four apps (A4A Radar, Grindr, Jack'd, and Scruff). Two-thirds (64 %) found apps to be an acceptable source for sexual health information. MSM who found apps as acceptable were more likely non-white, not sure of their current HIV status, and have low HIV testing self-efficacy. One-quarter (26 %) of informational chats with the health educator resulted in users requesting and being referred to local HIV/STD testing sites. There were significant differences in the number and types of interactions across apps. Established apps designed for MSM may be both an acceptable and feasible platform to promote HIV/STD testing. Future research should evaluate interventions that leverage this technology. PMID:25381563

  11. HIV Testing in Non-Traditional Settings – The HINTS Study: A Multi-Centre Observational Study of Feasibility and Acceptability

    Michael Rayment; Alicia Thornton; Sundhiya Mandalia; Gillian Elam; Mark Atkins; Rachael Jones; Anthony Nardone; Patrick Roberts; Melinda Tenant-Flowers; Jane Anderson; Sullivan, Ann K.

    2012-01-01

    BACKGROUND: UK guidelines recommend routine HIV testing in healthcare settings if the local diagnosed HIV prevalence >2/1000 persons. This prospective study assessed the feasibility and acceptability, to patients and staff, of routinely offering HIV tests in four settings: Emergency Department, Acute Care Unit, Dermatology Outpatients and Primary Care. Modelling suggested the estimated prevalence of undiagnosed HIV infection in attendees would exceed 1/1000 persons. The prevalence identified ...

  12. Stigma Management in Normal-Stigmatized Interactions: Test of the Disclosure Hypothesis and a Model of Stigma Acceptance.

    Seibold, David R.; Thompson, Teresa L.

    1978-01-01

    Describes a study exploring the efficacy of disclosure as a stigma management strategy in normal-stigmatized interactions. Path analysis of the data indicates a process leading from uncertainty, tension, and attraction to acceptance/rejection, as expected. Findings are discussed in terms of stigma attributions and relational development. (JMF)

  13. Acceptance tests on the first micro multi-leaf collimator (mMLC) for stereotactic radiosurgery and radiotherapy in India

    The micro multi-Leaf Collimator from BrainLAB integrated on Varian 2100 C/D Linear Accelerator underwent stringent commissioning and acceptance procedures. Excellent agreement was found with the specification standards recommended by national and international bodies. The use of mMLC for SRS and SRT is expected to result in good treatment outcome

  14. Review of the Aerodynamic Acceptance Test and Application to Anti-Icing Fluids Testing in the NRC Propulsion and Icing Wind Tunnel

    Broeren, Andy P.; Riley, James T.

    2012-01-01

    In recent years, the FAA has worked with Transport Canada, National Research Council of Canada (NRC) and APS Aviation, Inc. to develop allowance times for aircraft operations in ice-pellet precipitation. These allowance times are critical to ensure safety and efficient operation of commercial and cargo flights. Wind-tunnel testing with uncontaminated anti-icing fluids and fluids contaminated with simulated ice-pellets had been carried out at the NRC Propulsion and Icing Wind Tunnel (PIWT) to better understand the flowoff characteristics and resulting aerodynamic effects. The percent lift loss on the thin, high-performance wing model tested in the PIWT was determined at 8 angle of attack and used as one of the evaluation criteria in determining the allowance times. Because it was unclear as to how performance degradations measured on this model were relevant to an actual airplane configuration, some means of interpreting the wing model lift loss was deemed necessary. In this report, the lift loss was related to the loss in maximum lift of a Boeing 737-200ADV airplane through the Aerodynamic Acceptance Test (AAT) performed for fluids qualification. This report provides a review of the research basis of the AAT in order to understand how this correlation was applied. A loss in maximum lift coefficient of 5.24 percent on the B737-200ADV airplane (which was adopted as the threshold in the AAT) corresponds to a lift loss of 7.3 percent on the PIWT model at 8 degrees angle of attack. There is significant scatter in the data used to develop the correlation related to varying effects of the various antiicing fluids that were tested and other factors. A statistical analysis indicated the upper limit of lift loss on the PIWT model was 9.2 percent. Therefore, for cases resulting in PIWT model lift loss from 7.3 to 9.2 percent, extra scrutiny of the visual observations is required in evaluating fluid performance with contamination. Additional research may result in future

  15. Acceptable risk

    The hazards of nuclear power, radioactive wastes and radiation are analysed in a general book describing and defining acceptable-risk problems, the difficulties in resolving them and considering such issues as uncertainty about their definition, lack of relevant facts, conflicting and conflicted social values and disagreements between technical experts and the lay public. The many methods that have been proposed for resolving acceptable-risk problems are identified and criticised. (author)

  16. Development of test acceptance standards for qualification of the glass-bonded zeolite waste form. Interim annual report, October 1995 - September 1996

    Glass-bonded zeolite is being developed at Argonne National Laboratory in the Electrometallurgical Treatment Program as a potential ceramic waste form for the disposition of radionuclides associated with the US Department of Energy's (DOE's) spent nuclear fuel conditioning activities. The utility of standard durability tests [e.g. Materials Characterization Center Test No. 1 (MCC-1), Product Consistency Test (PCT), and Vapor Hydration Test (VHT)] are being evaluated as an initial step in developing test methods that can be used in the process of qualifying this material for acceptance into the Civilian Radioactive Waste Management System. A broad range of potential repository conditions are being evaluated to determine the bounding parameters appropriate for the corrosion testing of the ceramic waste form, and its behavior under accelerated testing conditions. In this report we provide specific characterization information and discuss how the durability test results are affected by changes in pH, leachant composition, and sample surface area to leachant volume ratios. We investigate the release mechanisms and other physical and chemical parameters that are important for establishing acceptance parameters, including the development of appropriate test methodologies required to measure product consistency

  17. Acceptability of self-conducted home-based HIV testing among men who have sex with men in Brazil: data from an on-line survey

    Lippman, Sheri A.; Périssé, André R. S.; Veloso, Valdiléa G.; Sullivan, Patrick S.; Buchbinder, Susan; Sineath, R. Craig; Grinsztejn, Beatriz

    2014-01-01

    The Brazilian HIV/AIDS epidemic is concentrated among men who have sex with men (MSM), however HIV testing rates among MSM are not commensurate with their risk. Strategies to expand early diagnosis may include use of self-conducted home-based testing kits, which are now available for purchase in the US. In April 2011 we conducted a survey with Brazilian MSM using Facebook to assess HIV testing preferences and acceptability of home-based testing. Among 356 previously tested, HIV-negative MSM, 47% reported a preference for home-based testing, 27% preferred clinic-based testing, and 26% had no preference. Less frequent testers and those who had considered testing but failed to test were more likely to prefer home-based testing. Close to 90% reported that they would use self-test kits; 62% and 54% said they would use home-based testing to make choices about unprotected sex with regular and new partners, respectively. Concerns included difficulty to understand the tests (32%) and receiving results alone (23%). Overall, home-based testing may appeal to MSM and result in increased testing frequency. Research on feasibility and utilization of self-tests in practice is needed. PMID:24896048

  18. Project W-314 updated acceptance test report HNF-4649 for HNF-4648 241-A pit leak detection ANA-WT-LDSTA-331 for project W-314

    The purpose of the test was to verify that the AN Tank Farm AN-A Pit Leak Detector components are functionally integrated and operate in accordance with engineering design specifications. The Acceptance Test Procedure HNF-4648,24l-AN-A-Pit Leak Detection ANA-WT-LDSTA-331 was conducted between 23 June and 01 July 1999 at the 200E AN Tank Farm. The test has been completed with no open test exceptions. The test was conducted prior to final engineering ''as built'' activities being completed this had no impact on the procedure or test results. All components, identified in the procedure were found to be labeled and identified as written in the procedure

  19. Project W-314 acceptance test report HNF-4647 for HNF-4646 241-B pit leak detection ANB-WT-LDSTA-231 for project W-314

    The purpose of the test was to verify that the AN Tank Farm B Pit Leak Detector components are functionally integrated and operate in accordance with engineering design specifications. The Acceptance Test Procedure HNF-4646,241-AN-B-Pit Leak Detection ANB-WT-LDSTA-231 was conducted between 26 June and 02 July 1999 at the 200E AN Tank Farm. The test has been completed with no open test exceptions. The test was conducted prior to final engineering ''as built'' activities being completed this had no impact on the procedure or test results. All components, identified in the procedure were found to be labeled and identified as written in the procedure

  20. Acceptance of non-invasive prenatal testing by cell free foetal DNA for foetal aneuploidy in a developing country: experience at a tertiary care centre in India

    Namrata Kashyap

    2016-03-01

    Conclusions: Newer genomic technology involving cell free maternal DNA is a new storm in prenatal diagnosis. Its application in clinical practice is the need of the hour, however, the lack of awareness, high cost and unavailability of the test in the country appears to be a major limiting factor for its poor acceptability. [Int J Reprod Contracept Obstet Gynecol 2016; 5(3.000: 705-710

  1. Physicochemical properties and sensory acceptability of goat’s milk fruit yogurts with mango and banana using accelerated testing

    Víctor Aredo; Lía Velásquez; María Lázaro

    2015-01-01

    Two types of skimmed (fat 3%) goat’s milk fruit yogurt with mango (YM) and banana (YB) were stored at temperatures of 5 °C, 15 °C and 25 °C for 72 hours. Every 24 hours the pH, titratable acidity, total solids, fat and protein were analyzed. Sensory acceptability was also evaluated with 75 yogurt frequent consumers, who responded with "yes" or "no" to the question ¿would you consume this product? At the beginning pH, acidity, total solids, fat and protein were 4.35 and 4.36; 0.76% and 0.75%; ...

  2. Experimental tests and validation of calculation criteria of acceptable Tk shift with respect to PTS at VVER

    The following topics were examined: (i) Methodology of fracture tests at temperature gradients and pressurized thermal shock (PTS) cooling tests on large specimens (1500x1200x140 mm) with a designed postulated crack and other smaller cracks in the cooled area (test performed on a ZZ 8000 (80MN) loading stand); (ii) simulation of radiation embrittlement of tested material near the end of the RPV designed life, the material is subjected to standard mechanical property tests and fracture tests of standard test specimens modelling the PTS regime of material loading; (iii) 100% NDT tests of a specimen before the beginning of tests and μTOFD before and after each particular test of a specimen; (iv) on-line monitoring of the test conditions based on instrumentation of a specimen with thermocouples, COD and strain gauges together with on-line monitoring of Acoustic Emission during the tests; (v) calculation of Kl at the critical points of the crack front during the test, based on monitored boundary conditions; (vi) fractographic analysis after the fracture of a specimen and evaluation of the whole test. (P.A.)

  3. Factors affecting acceptance of provider-initiated HIV testing and counseling services among outpatient clients in selected health facilities in Harar Town, Eastern Ethiopia

    Abdurahman S

    2015-05-01

    Full Text Available Sami Abdurahman,1 Berhanu Seyoum,2 Lemessa Oljira,2 Fitsum Weldegebreal2 1Harari Regional Health Bureau, 2Haramaya University, College of Health and Medical Sciences, Harar, Ethiopia Purpose: To improve the slow uptake of HIV counseling and testing, the World Health Organization (WHO and the Joint United Nations Programme on HIV/AIDS (UNAIDS have developed draft guidelines on provider-initiated testing and counseling (PITC. Both in low- and high-income countries, mainly from outpatient clinics and tuberculosis settings, indicates that the direct offer of HIV testing by health providers can result in significant improvements in test uptake. In Ethiopia, there were limited numbers of studies conducted regarding PITC in outpatient clinics. Therefore, in this study, we have assessed the factors affecting the acceptance of PITC among outpatient clients in selected health facilities in Harar, Harari Region State, Ethiopia. Materials and methods: Institutional-based, cross-sectional quantitative and qualitative studies were conducted from February 12–30, 2011 in selected health facilities in Harar town, Harari Region State, Ethiopia. The study participants were recruited from the selected health facilities of Harar using a systematic random sampling technique. The collected data were double entered into a data entry file using Epi Info version 3.5.1. The data were transferred to SPSS software version 16 and analyzed according to the different variables. Results: A total of 362 (70.6% clients accepted PITC, and only 39.4% of clients had heard of PITC in the outpatient department service. Age, occupation, marital status, anyone who wanted to check their HIV status, and the importance of PITC were the variables that showed significant associations with the acceptance of PITC upon bivariate and multivariate analyses. The main reasons given for not accepting the tests were self-trust, not being at risk for HIV, not being ready, needing to consult their

  4. Acceptance test for 900 MWe PWR unit replacement steam generators; Essai de reception des generateurs de vapeur de remplacement des tranches REP 900

    Gourguechon, B.

    1993-12-31

    During the first half of 1994, the Gravelines 1 steam generators will be replaced (SG replacement procedure). The new SG`s differ from the former components notably by the alloy used for the tube bundle, in this case, the high chromium content Inconel 690. So, from this standpoint, they are to be considered as PWR 900 replacement SG first models and their thermal efficiency has consequently to be assessed. This will provide an opportunity of ensuring that the performance of the components delivered is in compliance with requirements and of making the necessary provisions if significant deviations are observed. The EFMT branch, which has been in charge of the instrumentation and acceptance of the different SG first models since the first PWR plants were commissioned, will be responsible for the acceptance tests and the ultimate validation of a performance assessment procedure applicable to the future replacement steam generators. The methods and tests proposed for SG expert appraisal are based on consideration of the importance of primary measurement quality for satisfactory SG assessment and of the new test facilities with which the 900 and 1 300 PWR plants are gradually being equipped. These facilities provide an on-site computer environment for tests compatible with the tools (PATTERN, etc.) used at EFMT and in other departments. This test is the first of this kind performed by EFMT and the test facility of a nuclear power plant. (author). 6 figs.

  5. Acceptance of non-invasive prenatal testing by cell free foetal DNA for foetal aneuploidy in a developing country: experience at a tertiary care centre in India

    Namrata Kashyap; Mandakini Pradhan; Piyush Kumar; Neeta Singh

    2016-01-01

    Background: Non-invasive prenatal testing is a new technique which is deepening its root all over the world. Its tremendous potential lies in its ability of using cell free fetal DNA from the plasma of pregnant women. However, to what extent the technology has reached to a common person is also to be given a thought. hence the study was planned to assess the acceptability of non-invasive prenatal testing in Indian settings, to study about the awareness and baseline knowledge about Down's synd...

  6. Operations Acceptance Management

    Suchá, Ivana

    2010-01-01

    This paper examines the process of Operations Acceptance Management, whose main task is to control Operations Acceptance Tests (OAT). In the first part the author focuses on the theoretical ground for the problem in the context of ITSM best practices framework ITIL. Benefits, process pitfalls and possibilities for automation are discussed in this part. The second part contains a case study of DHL IT Services (Prague), where a solution optimizing the overall workflow was implemented using simp...

  7. Acceptance and Operational Test Report for Neutron and Gamma Probe Application to Tank 241-SY-101 MITs

    This Operational Test Report (OTR) presents the results of the ATP/OTP testing performed to verify that newly procured neutron and gamma probes (reduced diameter design modifications) for operation in the Tank 241-SY-101 MITs are compatible with existing LOW van instrumentation and hardware. This verification was accomplished and a set of moisture data versus elevation were obtained from the Tank 241-SY-101 MITs as part of this testing program

  8. Perceptions about the acceptability and prevalence of HIV testing and factors influencing them in different communities in South Africa

    Ntsepe, Yoliswa; Simbayi, Leickness C; Shisana, Olive; Rehle, Thomas; Mabaso, Musawenkosi; Ncitakalo, Nolusindiso; Davids, Alicia; Naidoo, Yogandra Dhee

    2014-01-01

    Abstract HIV counselling and testing (HCT) is considered important because it is an entry point to a comprehensive continuum of care for HIV/AIDS. The South African Department of Health launched an HCT campaign in April 2010, and this reached 13,269,746 people by June 2011, of which 16% tested HIV positive and 400,000 of those were initiated into antiretroviral treatment. The overall objective of this project was to gain insight into the general perceptions about HIV testing in the different ...

  9. Impact of a "TED-Style" presentation on potential patients' willingness to accept dental implant therapy: a one-group, pre-test post-test study

    Ghanem, Henry; Afrashtehfar, Kelvin Ian; Abi-Nader, Samer; Tamimi, Faleh

    2015-01-01

    PURPOSE A survey was conducted to assess the impact of a TED-like educational session on participants' willingness to accept dental implant therapy. MATERIALS AND METHODS Volunteers interested in having information about dental implant therapies were recruited and asked to complete a two-part survey before and after an educational session. The initial survey elicited demographic information, self-perceived knowledge on dental implants and willingness to this kind of treatment. A "TED-style" p...

  10. Rapid HIV Testing Is Highly Acceptable and Preferred among High-Risk Gay And Bisexual Men after Implementation in Sydney Sexual Health Clinics.

    Damian P Conway

    Full Text Available Rapid HIV testing (RHT is well established in many countries, but it is new in Australia. We assessed the acceptability of RHT and its associations among gay, bisexual and other men who have sex with men (GBM after implementation of RHT in Sydney sexual health clinics.GBM were invited to complete an acceptability questionnaire before and after provision of the result of finger-prick blood RHT, comparing their experience of RHT with conventional HIV testing (CHT involving venipuncture. Logistic regression was used to assess associations between patient characteristics and the preference for RHT over CHT next time they tested for HIV.Of 1061 GBM who received non-reactive RHT results, 59% found RHT less stressful than CHT and 34% reported no difference, and 61% found RHT more comfortable than CHT and 26% reported no difference. Nearly all men were satisfied with RHT result delivery (99% and the RHT process overall (99%. Most men (79% preferred RHT for their next HIV test and this preference was stronger in men who were aged 35-44 years (adjusted odds ratio [AOR] 2.49, p<0.01, reported they would test more often if RHT was available (AOR 1.66, p=0.01, found returning for results annoying (AOR 1.67, p=0.01, and found RHT less stressful (AOR 2.37, p<0.01 and more comfortable (AOR 1.62, p=0.02 than CHT. Men concerned about the reliability of RHT were less than half as likely to prefer RHT for their next HIV test (AOR 0.44, p<0.01.Most GBM preferred RHT to CHT next time and this preference was associated with finding RHT more convenient, more comfortable and less stressful than CHT. These findings suggest that in a clinic setting RHT should be considered to improve the patient experience and may potentially increase uptake and frequency of HIV testing.

  11. Rapid HIV Testing Is Highly Acceptable and Preferred among High-Risk Gay And Bisexual Men after Implementation in Sydney Sexual Health Clinics

    Conway, Damian P.; Guy, Rebecca; Davies, Stephen C; Couldwell, Deborah L.; McNulty, Anna; Smith, Don E.; Keen, Phillip; Cunningham, Philip; Holt, Martin

    2015-01-01

    Background Rapid HIV testing (RHT) is well established in many countries, but it is new in Australia. We assessed the acceptability of RHT and its associations among gay, bisexual and other men who have sex with men (GBM) after implementation of RHT in Sydney sexual health clinics. Methods GBM were invited to complete an acceptability questionnaire before and after provision of the result of finger-prick blood RHT, comparing their experience of RHT with conventional HIV testing (CHT) involving venipuncture. Logistic regression was used to assess associations between patient characteristics and the preference for RHT over CHT next time they tested for HIV. Results Of 1061 GBM who received non-reactive RHT results, 59% found RHT less stressful than CHT and 34% reported no difference, and 61% found RHT more comfortable than CHT and 26% reported no difference. Nearly all men were satisfied with RHT result delivery (99%) and the RHT process overall (99%). Most men (79%) preferred RHT for their next HIV test and this preference was stronger in men who were aged 35-44 years (adjusted odds ratio [AOR] 2.49, p<0.01), reported they would test more often if RHT was available (AOR 1.66, p=0.01), found returning for results annoying (AOR 1.67, p=0.01), and found RHT less stressful (AOR 2.37, p<0.01) and more comfortable (AOR 1.62, p=0.02) than CHT. Men concerned about the reliability of RHT were less than half as likely to prefer RHT for their next HIV test (AOR 0.44, p<0.01). Conclusions Most GBM preferred RHT to CHT next time and this preference was associated with finding RHT more convenient, more comfortable and less stressful than CHT. These findings suggest that in a clinic setting RHT should be considered to improve the patient experience and may potentially increase uptake and frequency of HIV testing. PMID:25898140

  12. Development and Acceptance Testing of the Dual Wheel Mechanism for the Tunable Filter Imager Cryogenic Instrument on the JWST

    Leckie, Martin; Ahmad, Zakir

    2010-01-01

    The James Webb Space Telescope (JWST) will carry four scientific instruments, one of which is the Tunable Filter Imager (TFI), which is an instrument within the Fine Guidance Sensor. The Dual Wheel (DW) mechanism is being designed, built and tested by COM DEV Ltd. under contract from the Canadian Space Agency. The DW mechanism includes a pupil wheel (PW) holding seven coronagraphic masks and two calibration elements and a filter wheel (FW) holding nine blocking filters. The DW mechanism must operate at both room temperature and at 35K. Successful operation at 35K comprises positioning each optical element with the required repeatability, for several thousand occasions over the five year mission. The paper discusses the results of testing geared motors and bearings at the cryogenic temperature. In particular bearing retainer design and PGM-HT material, the effects of temperature gradients across bearings and the problems associated with cooling mechanisms down to cryogenic temperatures. The results of additional bearing tests are described that were employed to investigate an abnormally high initial torque experienced at cryogenic temperatures. The findings of these tests, was that the bearing retainer and the ball/race system could be adversely affected by the large temperature change from room temperature to cryogenic temperature and also the temperature gradient across the bearing. The DW mechanism is now performing successfully at both room temperature and at cryogenic temperature. The life testing of the mechanism is expected to be completed in the first quarter of 2010.

  13. The Romanian experience on testing and quality acceptance criteria of packages used for transportation and storage of radioactive wastes

    Full text: The transport of radioactive wastes generated by nuclear facilities from non-power applications (research institutes, hospitals, nuclear fuel work) in Romania is one of the important subprograms of Romanian Waste Management and the overall aim is to promote the safe transport of the radioactive materials in Romania. According to the International Atomic Energy Agency Regulations on 'Safe Transport of Radioactive Materials' the package is the main instrument to ensure safety during handling, transport and storage of radioactive materials. After emphasizing the importance of the packaging tests in ensuring that the requisite safety features built into the design of packages comply with the Romanian Nuclear Regulatory Body - National Commission for Nuclear Activities Control (CNCAN) requirements and with IAEA's Regulations, the paper presents the type and production testing for type A packages (containers) which have been developed within Institute for Nuclear Research (INR) Pitesti taking into consideration that packages (drums) when tested to this requirements, should prevent: loss of dispersal of the radioactive contents, and loss of shielding integrity which results in more than a 20% increase in radiation level at any external surface of the package. The criteria used for successful testing of type A packages are: 'would prevent loss or dispersal'. The wastes to be packaged are generated by INR TRIGA research reactor, by the post-irradiation laboratory and radiochemistry activities such as: metallic pieces, protection equipment, used ion exchanger, organic liquid radioactive wastes, used filters, etc. The paper describes and contains: a review of the qualification tests that have been laid down to simulate different conditions encountered during transport, normal conditions as well as the accident. These tests have been performed in order to simulate specific or accident scenarios and to produce the same kind of amount of damage that account for the

  14. Project W-314 acceptance test report HNF-4643 for HNF-4642 241-AN-A valve pit manifold valves and position indication for project W-314

    HAMMERS, J.S.

    1999-09-22

    The purpose of the test was to verify that the AN Tank Farm Manifold Valves can be manually manipulated to the required operating position and that the electrical and visual indications accurately reflect that position. Physical locking devices were also verified to function. The Acceptance Test Procedure HNF-4642, 241-AN-A Valve Pit Manifold Valves and Position Indication was conducted between 23 June and 10 August 1999 at the 200E AN Tank Farm. The test has no open test exceptions. The test was conducted prior to final engineering ''as built'' activities being completed, this had an impact on the procedure and test results, ECN 653752 was written to correct the mismatch between the procedure and actual field conditions. P&ID H-14-100941 was changed via ECN-W-314-4C-120. All components, identified in the procedure, were not found to be labeled and identified as written in the procedure, temporary tags were used for operational identification. A retest of valve ANA-WT-V 318 was required because it was removed from its installed position and modified after testing was completed.

  15. Project W-314 acceptance test report HNF-4643 for HNF-4642 241-AN-A valve pit manifold valves and position indication for project W-314

    The purpose of the test was to verify that the AN Tank Farm Manifold Valves can be manually manipulated to the required operating position and that the electrical and visual indications accurately reflect that position. Physical locking devices were also verified to function. The Acceptance Test Procedure HNF-4642, 241-AN-A Valve Pit Manifold Valves and Position Indication was conducted between 23 June and 10 August 1999 at the 200E AN Tank Farm. The test has no open test exceptions. The test was conducted prior to final engineering ''as built'' activities being completed, this had an impact on the procedure and test results, ECN 653752 was written to correct the mismatch between the procedure and actual field conditions. P and ID H-14-100941 was changed via ECN-W-314-4C-120. All components, identified in the procedure, were not found to be labeled and identified as written in the procedure, temporary tags were used for operational identification. A retest of valve ANA-WT-V 318 was required because it was removed from its installed position and modified after testing was completed

  16. Early experiences on the feasibility, acceptability, and use of malaria rapid diagnostic tests at peripheral health centres in Uganda-insights into some barriers and facilitators

    Asiimwe Caroline

    2012-01-01

    Full Text Available Abstract Background While feasibility of new health technologies in well-resourced healthcare settings is extensively documented, it is largely unknown in low-resourced settings. Uganda's decision to deploy and scale up malaria rapid diagnostic tests (mRDTs in public health facilities and at the community level provides a useful entry point for documenting field experience, acceptance, and predictive variables for technology acceptance and use. These findings are important in informing implementation of new health technologies, plans, and budgets in low-resourced national disease control programmes. Methods A cross-sectional qualitative descriptive study at 21 health centres in Uganda was undertaken in 2007 to elucidate the barriers and facilitators in the introduction of mRDTs as a new diagnostic technology at lower-level health facilities. Pre-tested interview questionnaires were administered through pre-structured patient exit interviews and semi-structured health worker interviews to gain an understanding of the response to this implementation. A conceptual framework on technology acceptance and use was adapted for this study and used to prepare the questionnaires. Thematic analysis was used to generate themes from the data. Results A total of 52 of 57 health workers (92% reported a belief that a positive mRDT result was true, although only 41 of 57 (64% believed that treatment with anti-malarials was justified for every positive mRDT case. Of the same health workers, only 49% believed that a negative mRDT result was truly negative. Factors linked to these findings were related to mRDT acceptance and use, including the design and characteristics of the device, availability and quality of mRDT ancillary supplies, health worker capacity to investigate febrile cases testing negative with the device and provide appropriate treatment, availability of effective malaria treatments, reliability of the health commodity supply chain, existing national

  17. Acceptance test for the linear motion actuator for the scanning slit of the HIE-ISOLDE short diagnostic boxes

    Cantero, E D; Bravin, E; Sosa, A

    2014-01-01

    We performed experimental tests to characterize the mechanical accuracy of a linear actuator designed by the company AVS for the movement of the scanning slit of the HIE-ISOLDE short diagnostic boxes. The mechanism consists of a linear actuator composed of two guiding rods and a lead screw, with a full stroke of 135 mm. A specially designed blade was mounted on the actuator and the transverse positioning of the blade was monitored with a camera-based optical system while moving the actuator at speeds of up to 10 mm/s. The repeatability of the positioning of the blade after several cycles around predefined positions was also measured. The results of the measurements and a general inspection of the device show that the proposed solution fulfils the specifications. A full prototype of short diagnostic box for the HIE-ISOLDE project can now be built for testing.

  18. Acceptance test procedure for the ultra high pressure bore head for use in the self-installing liquid observation well

    In order to monitor waste stored in single-shell tanks, liquid observation wells (LOWs) are installed to permit periodic insertion of instrumentation probes to evaluate the waste cross sections. An ultra high pressure water bore head, developed for installing instrument trees, was adapted for use with the LOWs. The modification facilitates the removal of the high pressure water feed system after installation. This document describes a series of tests that ensures that the design meets all the functional requirements

  19. Correlation between amount of virus with altered nucleotide sequence and the monkey test for acceptability of oral poliovirus vaccine.

    Chumakov, K M; Powers, L B; Noonan, K E; Roninson, I B; Levenbook, I S

    1991-01-01

    Production of live attenuated oral poliomyelitis vaccine (OPV) requires rigorous neurovirulence safety testing of each vaccine lot, currently carried out in monkeys. It has been reported that a change from 472-U to 472-C in the type 3 OPV RNA is associated with an increased histologic lesion score produced upon intraspinal inoculation of the mutant virus in monkeys. We have developed a method, based on polymerase chain reaction, for measuring the relative abundance of these mutant sequences d...

  20. Dispensary level pilot implementation of rapid diagnostic tests: an evaluation of RDT acceptance and usage by providers and patients – Tanzania, 2005

    O'Reilly Terrence

    2008-11-01

    Full Text Available Abstract Background Malaria rapid diagnostic tests (RDTs may assist in diagnosis, improve prescribing practices and reduce potential drug resistance development. Without understanding operational issues or acceptance and usage by providers and patients, the costs of these tests may not be justified. Objectives To evaluate the impact of RDTs on prescribing behaviours, assess prescribers' and patients' perceptions, and identify operational issues during implementation. Methods Baseline data were collected at six Tanzanian public dispensaries. RDTs were implemented for eight weeks and data collected on frequency of RDT use, results, malaria diagnoses and the prescription of antimalarials. Patients referred for RDTs completed a standardised exit interview. Qualitative methods assessed attitudes toward and satisfaction with RDTs, perceptions about the test and operational issues related to implementation. Results Of 595 patients at baseline, 200 (33% were diagnosed clinically with malaria but had a negative RDT. Among the 2519 RDTs performed during implementation, 289 (11.5% had a negative result and antimalarials prescribed. The proportion of "over-prescriptions" at baseline was 54.8% (198/365. At weeks four and eight this decreased to 16.1% (27/168 and 16.4% (42/256 respectively. A total of 355 patient or parent/caregiver and 21 prescriber individual interviews and 12 focus group discussions (FGDs were conducted. Patients, caregivers and providers trusted RDT results, agreed that use of RDTs was feasible at dispensary level, and perceived that RDTs improved clinical diagnosis. Negative concerns included community suspicion and fear that RDTs were HIV tests, the need for additional supervision in interpreting the results, and increased work loads without added compensation. Conclusion Overprescriptions decreased over the study period. There was a high degree of patient/caregiver and provider acceptance of and satisfaction with RDTs. Implementation

  1. SU-C-304-02: Robust and Efficient Process for Acceptance Testing of Varian TrueBeam Linacs Using An Electronic Portal Imaging Device (EPID)

    Purpose: The purpose of this project was to develop a process that utilizes the onboard kV and MV electronic portal imaging devices (EPIDs) to perform rapid acceptance testing (AT) of linacs in order to improve efficiency and standardize AT equipment and processes. Methods: In this study a Varian TrueBeam linac equipped with an amorphous silicon based EPID (aSi1000) was used. The conventional set of AT tests and tolerances was used as a baseline guide, and a novel methodology was developed to perform as many tests as possible using EPID exclusively. The developer mode on Varian TrueBeam linac was used to automate the process. In the current AT process there are about 45 tests that call for customer demos. Many of the geometric tests such as jaw alignment and MLC positioning are performed with highly manual methods, such as using graph paper. The goal of the new methodology was to achieve quantitative testing while reducing variability in data acquisition, analysis and interpretation of the results. The developed process was validated on two machines at two different institutions. Results: At least 25 of the 45 (56%) tests which required customer demo can be streamlined and performed using EPIDs. More than half of the AT tests can be fully automated using the developer mode, while others still require some user interaction. Overall, the preliminary data shows that EPID-based linac AT can be performed in less than a day, compared to 2–3 days using conventional methods. Conclusions: Our preliminary results show that performance of onboard imagers is quite suitable for both geometric and dosimetric testing of TrueBeam systems. A standardized AT process can tremendously improve efficiency, and minimize the variability related to third party quality assurance (QA) equipment and the available onsite expertise. Research funding provided by Varian Medical Systems. Dr. Sasa Mutic receives compensation for providing patient safety training services from Varian Medical

  2. SU-C-304-02: Robust and Efficient Process for Acceptance Testing of Varian TrueBeam Linacs Using An Electronic Portal Imaging Device (EPID)

    Yaddanapudi, S; Cai, B; Sun, B; Li, H; Noel, C; Goddu, S; Mutic, S [Washington University School of Medicine, Saint Louis, MO (United States); Harry, T [Oregon State University, Corvallis, OR (United States); Pawlicki, T [UCSD Medical Center, La Jolla, CA (United States)

    2015-06-15

    Purpose: The purpose of this project was to develop a process that utilizes the onboard kV and MV electronic portal imaging devices (EPIDs) to perform rapid acceptance testing (AT) of linacs in order to improve efficiency and standardize AT equipment and processes. Methods: In this study a Varian TrueBeam linac equipped with an amorphous silicon based EPID (aSi1000) was used. The conventional set of AT tests and tolerances was used as a baseline guide, and a novel methodology was developed to perform as many tests as possible using EPID exclusively. The developer mode on Varian TrueBeam linac was used to automate the process. In the current AT process there are about 45 tests that call for customer demos. Many of the geometric tests such as jaw alignment and MLC positioning are performed with highly manual methods, such as using graph paper. The goal of the new methodology was to achieve quantitative testing while reducing variability in data acquisition, analysis and interpretation of the results. The developed process was validated on two machines at two different institutions. Results: At least 25 of the 45 (56%) tests which required customer demo can be streamlined and performed using EPIDs. More than half of the AT tests can be fully automated using the developer mode, while others still require some user interaction. Overall, the preliminary data shows that EPID-based linac AT can be performed in less than a day, compared to 2–3 days using conventional methods. Conclusions: Our preliminary results show that performance of onboard imagers is quite suitable for both geometric and dosimetric testing of TrueBeam systems. A standardized AT process can tremendously improve efficiency, and minimize the variability related to third party quality assurance (QA) equipment and the available onsite expertise. Research funding provided by Varian Medical Systems. Dr. Sasa Mutic receives compensation for providing patient safety training services from Varian Medical

  3. Feasibility and acceptability of point of care HIV testing in community outreach and GUM drop-in services in the North West of England: A programmatic evaluation

    Jelliman Pauline

    2011-06-01

    Full Text Available Abstract Background In Liverpool, injecting drug users (IDUs, men-who-have-sex-with-men (MSM and UK Africans experience a disproportionate burden of HIV, yet services do not reach out to these groups and late presentations continue. We set out to: increase testing uptake in targeted marginalized groups through a community and genitourinary medicine (GUM-based point of care testing (POCT programme; and conduct a process evaluation to examine service provider inputs and document service user perceptions of the programme. Methods Mixed quantitative, qualitative and process evaluation methods were used. Service providers were trained to use fourth generation rapid antibody/antigen HIV tests. Existing outreach services incorporated POCT into routine practice. Clients completed a semi-structured questionnaire and focus group discussions (FGDs were held with service providers. Results Between September 2009 and June 2010, 953 individuals underwent POCT (GUM: 556 [59%]; community-based sites: 397 [42%]. Participants in the community were more likely to be male (p = 0.028, older (p Conclusions Community and GUM clinic-based POCT for HIV was feasible and acceptable to clients and service providers in a low prevalence setting. It successfully reached target groups, many of whom would not have otherwise tested. We recommend POCT be considered among strategies to increase the uptake of HIV testing among groups who are currently underserved.

  4. Whole-body PET acceptance test in 2D and 3D using NEMA NU 2-2001 protocol

    Integrated PET/CT has emerged as an integral component of oncology management because of its unique potential of providing both functional and morphological images in a single imaging session. In this work, performance of the 'bismuth germinate (BGO) crystal'-based PET of a newly installed Discovery ST PET/CT was evaluated in 2D and 3D mode for whole-body scanning using National Electrical Manufacturers Association (NEMA) NU 2-2001 protocol and the recommended phantoms. During the entire measurements, the system operates with an energy window of 375-650 keV and 11.7 ns coincidence time window. The set of tests performed were spatial resolution, sensitivity, scatter fraction (SF) and counting rate performance. The average transaxial and axial spatial resolution measured as full width at half maximum (FWHM) of the point spread function at 1 cm (and 10 cm) off-axis was 0.632 (0.691) and 0.491 (0.653) cm in 2D and 0.646 (0.682) and 0.54 (0.601) cm in 3D respectively. The average sensitivity for the two radial positions (R = 0 cm and R = 10 cm) was 2.56 (2.63) cps/kBq in 2D and 11.85 (12.14) cps/kBq in 3D. The average scatter fraction was 19.79% in 2D and 46.19% in 3D. The peak noise equivalent counting rate (NECR) evaluated with single random subtraction was 89.41 kcps at 49 kBq/cc in 2D and 60 kcps at 12 kBq/cc in 3D acquisition mode. The NECR with delayed random subtraction was 61.47 kcps at 40.67 kBq/cc in 2D and 45.57 kcps at 16.45 kBq/cc in 3D. The performance of the PET scanner was satisfactory within the manufacturer-specified limits. The test result of PET shows excellent system sensitivity with relatively uniform resolution throughout the FOV, making this scanner highly suitable for whole-body studies. (author)

  5. Acceptance/operational test procedure 101-AW tank camera purge system and 101-AW video camera system

    This procedure will document the satisfactory operation of the 101-AW Tank Camera Purge System (CPS) and the 101-AW Video Camera System. The safety interlock which shuts down all the electronics inside the 101-AW vapor space, during loss of purge pressure, will be in place and tested to ensure reliable performance. This procedure is separated into four sections. Section 6.1 is performed in the 306 building prior to delivery to the 200 East Tank Farms and involves leak checking all fittings on the 101-AW Purge Panel for leakage using a Snoop solution and resolving the leakage. Section 7.1 verifies that PR-1, the regulator which maintains a positive pressure within the volume (cameras and pneumatic lines), is properly set. In addition the green light (PRESSURIZED) (located on the Purge Control Panel) is verified to turn on above 10 in. w.g. and after the time delay (TDR) has timed out. Section 7.2 verifies that the purge cycle functions properly, the red light (PURGE ON) comes on, and that the correct flowrate is obtained to meet the requirements of the National Fire Protection Association. Section 7.3 verifies that the pan and tilt, camera, associated controls and components operate correctly. This section also verifies that the safety interlock system operates correctly during loss of purge pressure. During the loss of purge operation the illumination of the amber light (PURGE FAILED) will be verified

  6. Acceptability, acceptance and decision making

    There is a fundamental difference between the acceptability of a civilizatory or societal risk and the acceptability of the decision-making process that leads to a civilizatory or societal risk. The analysis of individual risk decisions - regarding who, executes when which indisputably hazardous, unhealthy or dangerous behaviour under which circumstances - is not helpful in finding solutions for the political decisions at hand in Germany concerning nuclear energy in particular or energy in general. The debt for implementation of any technology, in the sense of making the technology a success in terms of broad acceptance and general utilisation, lies with the particular industry involved. Regardless of the technology, innovation research identifies the implementation phase as most critical to the success of any innovation. In this sense, nuclear technology is at best still an innovation, because the implementation has not yet been completed. Fear and opposition to innovation are ubiquitous. Even the economy - which is often described as 'rational' - is full of this resistance. Innovation has an impact on the pivotal point between stability, the presupposition for the successful execution of decisions already taken and instability, which includes insecurity, but is also necessary for the success of further development. By definition, innovations are beyond our sphere of experience; not at the level of reliability and trust yet to come. Yet they are evaluated via the simplifying heuristics for making decisions proven not only to be necessary and useful, but also accurate in the familiar. The 'settlement of the debt of implementation', the accompanying communication, the decision-making procedures concerning the regulation of averse effects of the technology, but also the tailoring of the new technology or service itself must be directed to appropriate target groups. But the group often aimed at in the nuclear debate, the group, which largely determines political

  7. Protocolo de testes de aceitação em equipamentos de imagem por ressonância magnética Acceptance testing protocol for magnetic resonance imaging systems

    Alessandro André Mazzola

    2005-06-01

    Full Text Available OBJETIVO: Este trabalho tem como objetivo criar um protocolo de testes de aceitação para equipamentos de imagem por ressonância magnética e demonstrar como e quais tipos de dispositivos de teste podem ser usados para a coleta de dados. MATERIAIS E MÉTODOS: Para cada um dos 15 testes selecionados foram elaborados a definição, o procedimento, a forma de análise e o critério de aceitação. RESULTADOS: Através dos testes de aceitação descritos é possível verificar características técnicas que constam nas propostas de venda dos fabricantes, assim como estabelecer valores de referências para serem utilizados em posteriores testes de constância. CONCLUSÃO: Futuros programas de garantia da qualidade em imagem por ressonância magnética devem considerar testes semelhantes ou iguais aos descritos neste trabalho.OBJECTIVE: To develop an acceptance testing protocol for magnetic resonance imaging systems and to show which and how phantoms could be used to collect data. MATERIALS AND METHODS: The definition, procedure, analysis and the acceptation criteria were created for each of 15 selected tests. RESULTS: These tests allow the evaluation of technical specifications stated on the manufacturer's sales proposal and to establish reference values to be used in subsequent constancy tests. CONCLUSION: Future quality assurance programs in magnetic resonance imaging should consider employing tests similar or equal to the ones described in this paper.

  8. Refraining from intrusive thoughts is strategy dependent: a comment on Sugiura, et al. And a preliminary informal test of detached mindfulness, acceptance, and other strategies.

    Wells, Adrian; Roussis, Panagiotis

    2014-10-01

    The control of cognition is fundamental to psychological well being. One dimension recently explored by Sugiura, Sugiura and Tanno (2013) is the perceived ability to refrain from catastrophic thinking-a construct that could be a marker of several factors. The current paper recommends deeper consideration in terms of metacognitive theory and exemplifies this by testing the effect of a strategy that focuses on abstaining from processes (detached mindfulness) vs. transforming content (acceptance, brief exposure). Fifty-six participants (M age = 21.5 yr., range = 18-42) were randomly assigned to detached mindfulness, acceptance, exposure, or a control group before watching a stressful film that induced intrusive images. Afterwards, they engaged in their respective strategies for 5 min. and the frequency of intrusive images was rated. Detached mindfulness was the only manipulation that was associated with a statistically significant lower frequency of intrusions than the control condition. It is argued that assessment of perceived skills to refrain from thinking should be conceptualized within a metacognitive framework that distinguish process- and content-oriented strategies and address the question: When is a strategy a true refrain? PMID:25243365

  9. Measurements and calculations of water velocity, momentum flux, and related flow parameters obtaned from single-phase water integral acceptance tests of the PKL instrumented spool pieces

    Stein, W.

    1979-10-09

    The operation of the emergency core cooling system and its related steam-binding problems in pressurized water reactors is the subject of a cooperative study by the United States, Germany, and Japan. Lawrence Livermore Laboratory and EG and G, Inc., San Ramon Operations, are responsible for the design, hardware, and software of the 80.8-mm and 113-mm spool piece measurement systems for the German Primarkreislauf (PKL) Test Facility at Kraftwerk Union in Erlangen, West Germany. This work was done for the US Nuclear Regulatory Commission, Division of Reactor Safety Research, under its 3-D Technical Support and Instrumentation Program. Four instrumented spools capable of measuring individual phase parameters in two-phase flows were constructed. Each spool contains a flow turbine, drag screen, three-beam densitometer, and pressure and temperature probes. A computerized data acquisition system is also provided to store and analyze data from the four spools. The four spools were shipped to the PKL Test Facility in West Germany for acceptance testing in a water-flow loop. Spool measurements of velocity and momentum flux were compared to the values obtained from an orifice meter installed in the loop piping system. The turbine flowmeter velocity data for all tests were within allowable tolerances. Drag screen momentum flux measurements were also within tolerance with the exception of a few points.

  10. Measurements and calculations of water velocity, momentum flux, and related flow parameters obtaned from single-phase water integral acceptance tests of the PKL instrumented spool pieces

    The operation of the emergency core cooling system and its related steam-binding problems in pressurized water reactors is the subject of a cooperative study by the United States, Germany, and Japan. Lawrence Livermore Laboratory and EG and G, Inc., San Ramon Operations, are responsible for the design, hardware, and software of the 80.8-mm and 113-mm spool piece measurement systems for the German Primarkreislauf (PKL) Test Facility at Kraftwerk Union in Erlangen, West Germany. This work was done for the US Nuclear Regulatory Commission, Division of Reactor Safety Research, under its 3-D Technical Support and Instrumentation Program. Four instrumented spools capable of measuring individual phase parameters in two-phase flows were constructed. Each spool contains a flow turbine, drag screen, three-beam densitometer, and pressure and temperature probes. A computerized data acquisition system is also provided to store and analyze data from the four spools. The four spools were shipped to the PKL Test Facility in West Germany for acceptance testing in a water-flow loop. Spool measurements of velocity and momentum flux were compared to the values obtained from an orifice meter installed in the loop piping system. The turbine flowmeter velocity data for all tests were within allowable tolerances. Drag screen momentum flux measurements were also within tolerance with the exception of a few points

  11. 可接受噪声级测试临床应用可行性探讨%A Study of Clinical Feasibility of Acceptable Noise Level Test

    胡旭君; 胡湘云; 李文靖

    2013-01-01

    目的探讨普通话可接受噪声级测试中给予受试者不同测试指令对结果的影响。方法将12名听力正常(听阈≤15dB HL)年轻人随机等分成两组,每组6人,A组先采用测试方法一(受试者接受口头测试指令,指令内容因测试者对英文指令的不同理解而不同),半小时后再采用测试方法二(受试者接受预先指定的完全一致书面测试指令),分别测试各对象普通话可接受噪声级值,B组测试方法则反之,比较两种测试方法测得的12名受试者的平均可接受噪声级(acceptable noise level ,ANL)、平均最舒适响度级(most comfortable level ,MCL)和平均可接受最大背景噪声级(background noise level ,BNL)。结果A、B组12名受试者两种测试方法所测得ANL值为7.51±6.61、8.29±6.54dBSPL;MCL值分别为83.58±8.57、85.41±8.89dBSPL,BNL值分别为78.92±10.56、77.13±7.91dBSPL,两种测试方法所得MCL、BNL、ANL值之间差异无统计学意义(P>0.05)。方法一所得ANL值范围为-6.40~17.10dBSPL,方法二所得ANL值范围为2.50~20.12dBSPL。不同个体在同一测试所得ANL值差异较大,同一个体前后两次测试所得ANL值差异无统计学意义(P>0.05)。结论不同的测试指令对普通话可接受噪声级值并无直接影响,测试者可根据对英文指令的理解进行ANL测试。%Objective To observe the clinical feasibility of the acceptable noise level (ANL) test ,analyze the effect of different test instructions to the result of Mandarin acceptable noise level test .Methods Twelve young peo-ple (24 ears) with normal pure-tone test and acoustic immittance test (threshold≤15 dB HL) were included in this study .They were randomly divided into two groups with 12 ears in each group .Group A received the same test in-struction firstly and then received different instructions depended on the different

  12. 普通话可接受噪声级的复测信度分析%Test-retest reliability of Mandarin acceptable noise level

    吴丹; 张华; 陈建勇; 王硕; 陈静; 吴燕君; 李玉玲; 任丹丹

    2013-01-01

    Objective:To evaluate test-retest reliability of Mandarin acceptable noise leveKM-ANL) test materials. Method:M-ANL was evaluated during three test sessions approximately one week apart, by testing 30 Mandarin-speaking people aged from 21 to 28 with normal aural/oral communicational abilities. The participants completed the preference for background noise questionnaire before the first session. Analysis of the test-retest results were administered by SPSS 17. 0 (Statistically Package for the Social Sciences Software Version 17. 0). Result: ANLs in the three sessions were(8. 1 ± 2. 9) , (7. 4±2. 2), (7. 6 ± 2. 5)dB S/N,respectively. The correlation coefficients were 0. 722,0. 746 and 0. 849 between two of the three sessions. The correlation coefficients of the ANL and 7 questions of the questionnaire were below 0. 3. Conclusion:M-ANL test materials are found to have good test-retest reliability. Listeners' preference for background noise is not related to their acceptance of background noise. Listeners cannot accurately assess their ability to accept background noise.%目的:通过对普通话可接受噪声级(M-ANL)材料进行复测信度评估,分析正常人的ANL与对噪声耐受的关系.方法:选取听力言语正常的21~28岁青年受试者30例,对其进行M-ANL测试,再分别于1周及2周后,以同样的测试条件进行第2次复测.每位受试者于第1次测试前填写1份对噪声耐受问卷.使用SPSS17.0软件对结果进行统计学分析.结果:3次ANL值分别为(8.1±2.9)dB S/N、(7.4±2.2)dB S/N、(7.6±2.5)dB S/N,两两配对t检验及Pearson相关分析,P=0.079、0.147、0.588,r=0.722、0.746、0.849.ANL与问卷中7个问题得分均r<0.3.结论:M-ANL测试具有较好的复测信度;个体对噪声的耐受与ANL无关,其并不能正确地自我判断实际对噪声的接受能力.

  13. [Possibilities of testing the biological acceptability of composite filling materials, with special reference to the microscopic test for pulp vitality. Review of the literature].

    Nyárasdy, I

    1990-08-01

    The main problem of microscopically observing the living pulpa consists in that it lies embedded into hard tissue. The haemodynamics of the pulpa may be defined by studying the physical parameters by examining the characteristics of blood flow and by the factors determining them. By comparison with other tissues little work is dealing with regulating the blood flow. The vital microscopic model of the rat incisor pulpa was first employed by Gängler to testing dental filling materials. The results thereof well complete the findings of standardized tests. On basis of the foregoing the sublining in case of clinical employment of composite filling materials is unconditionally suggested. PMID:2401373

  14. Protocol for stage 2 of the GaP study (genetic testing acceptability for Paget's disease of bone: A questionnaire study to investigate whether relatives of people with Paget's disease would accept genetic testing and preventive treatment if they were available

    McCallum Marilyn

    2008-05-01

    Full Text Available Abstract Background Paget's disease of bone (PDB disrupts normal bone architecture and causes pain, deformity, deafness, osteoarthritis, and fractures. Genetic factors play a role in PDB and genetic tests are now conducted for research purposes. It is thus timely to investigate the potential for a clinical programme of genetic testing and preventative treatment for people who have a family history of PDB. This study examines the beliefs of relatives of people with PDB. It focuses particularly on illness and treatment representations as predictors of the acceptability and uptake of potential clinical programmes. Illness representations are examined using Leventhal's Common Sense Self-Regulation Model while cognitions about treatment behaviours (acceptance of testing and treatment uptake are conceptualised within the Theory of Planned Behaviour. Methods/Design A postal questionnaire of non-affected relatives of people with Paget's disease. The sample will include relatives of Paget's patients with a family history of Paget's disease and relatives of Paget's patients without a family history of Paget's disease. The questionnaire will explore whether a range of factors relate to acceptability of a programme of genetic testing and preventive treatment in relatives of Paget's disease sufferers. The questionnaire will include several measures: illness representations (as measured by the Brief Illness Perceptions Questionnaire; treatment representations (as measured by Theory of Planned Behaviour-based question items, informed by a prior interview elicitation study; descriptive and demographic details; and questions exploring family environment and beliefs of other important people. Data will also be collected from family members who have been diagnosed with Paget's disease to describe the disease presentation and its distribution within a family. Discussion The answers to these measures will inform the feasibility of a programme of genetic testing and

  15. Attitudes and factors affecting acceptability of self-administered cervicovaginal sampling for human papillomavirus (HPV) genotyping as an alternative to Pap testing among multiethnic Malaysian women

    Ma'som, Mahirah; Bhoo-Pathy, Nirmala; Nasir, Nazrila Hairizan; Bellinson, Jerome; Subramaniam, Shridevi; Ma, Yuntong; Yap, Siew-Hwei; Goh, Pik-Pin; Gravitt, Patti; Woo, Yin Ling

    2016-01-01

    Objective The objective of this study was to determine the attitudes and acceptability of self-administered cervicovaginal sampling compared with conventional physician-acquired Papanicolaou (Pap) smear among multiethnic Malaysian women. Method A cross-sectional study was carried out via interviewer-administered surveys from August 2013 through August 2015 at five government-run, urban health clinics in the state of Selangor. Subjects were participants from an ongoing community-based human papillomavirus (HPV) prevalence study who answered a standard questionnaire before and after self-sampling. The cervicovaginal self-sampling for HPV genotyping was performed using a simple brush (‘Just for Me’; Preventive Oncology International, Hong Kong). Detailed data on sociodemographics, previous Pap smear experience, and attitudes towards self-administered cervicovaginal sampling were collected and analysed. Acceptability was inferred using a five-item Likert scale that included six different subjective descriptives: experience, difficulty, convenience, embarrassment, discomfort or pain, and confidence in collecting one's own sample. Results Of the 839 participants, 47.9% were Malays, followed by 30.8% Indians, 18.8% Chinese and 2.5% from other ethnicities. The median age of the participants was 38 years (IQR 30–48). Some 68.2% of participants indicated a preference for self-sampling over the Pap test, with 95% indicating willingness to follow-up a positive result at the hospital. Age, ethnicity and previous Pap test experience were significant independent factors associated with preference for self-sampling. The older the individual, the less likely they were to prefer self-sampling (adjusted OR 0.94, 95% CI 0.90 to 0.98). The Chinese were less likely to prefer self-sampling (72.6%) than the Malays (85.1%) (adjusted OR 0.57, 95% CI 0.33 to 0.98, p=0.004). Participants who had never undergone a Pap smear were also more likely to prefer self-sampling (88.5%) than

  16. International Fusion Materials Irradiation Facility injector acceptance tests at CEA/Saclay: 140 mA/100 keV deuteron beam characterization

    Gobin, R., E-mail: rjgobin@cea.fr; Bogard, D.; Chauvin, N.; Chel, S.; Delferrière, O.; Harrault, F.; Mattei, P.; Senée, F. [Commissariat à l’Energie Atomique et aux Energies Alternatives, CEA/Saclay, DSM/IRFU, 91191-Gif/Yvette (France); Cara, P. [Fusion for Energy, BFD Department, Garching (Germany); Mosnier, A. [Commissariat à l’Energie Atomique et aux Energies Alternatives, CEA/Saclay, DSM/IRFU, 91191-Gif/Yvette (France); Fusion for Energy, BFD Department, Garching (Germany); Shidara, H. [IFMIF/EVEDA Project Team, Obuchi-Omotedate 2-166, Rokkasho, Aomori (Japan); Okumura, Y. [JAEA, Division of Rokkasho BA Project, Obuchi-Omotedate 2-166, Rokkasho, Aomori (Japan)

    2014-02-15

    In the framework of the ITER broader approach, the International Fusion Materials Irradiation Facility (IFMIF) deuteron accelerator (2 × 125 mA at 40 MeV) is an irradiation tool dedicated to high neutron flux production for future nuclear plant material studies. During the validation phase, the Linear IFMIF Prototype Accelerator (LIPAc) machine will be tested on the Rokkasho site in Japan. This demonstrator aims to produce 125 mA/9 MeV deuteron beam. Involved in the LIPAc project for several years, specialists from CEA/Saclay designed the injector based on a SILHI type ECR source operating at 2.45 GHz and a 2 solenoid low energy beam line to produce such high intensity beam. The whole injector, equipped with its dedicated diagnostics, has been then installed and tested on the Saclay site. Before shipment from Europe to Japan, acceptance tests have been performed in November 2012 with 100 keV deuteron beam and intensity as high as 140 mA in continuous and pulsed mode. In this paper, the emittance measurements done for different duty cycles and different beam intensities will be presented as well as beam species fraction analysis. Then the reinstallation in Japan and commissioning plan on site will be reported.

  17. International Fusion Materials Irradiation Facility injector acceptance tests at CEA/Saclay: 140 mA/100 keV deuteron beam characterization.

    Gobin, R; Bogard, D; Cara, P; Chauvin, N; Chel, S; Delferrière, O; Harrault, F; Mattei, P; Mosnier, A; Senée, F; Shidara, H; Okumura, Y

    2014-02-01

    In the framework of the ITER broader approach, the International Fusion Materials Irradiation Facility (IFMIF) deuteron accelerator (2 × 125 mA at 40 MeV) is an irradiation tool dedicated to high neutron flux production for future nuclear plant material studies. During the validation phase, the Linear IFMIF Prototype Accelerator (LIPAc) machine will be tested on the Rokkasho site in Japan. This demonstrator aims to produce 125 mA/9 MeV deuteron beam. Involved in the LIPAc project for several years, specialists from CEA/Saclay designed the injector based on a SILHI type ECR source operating at 2.45 GHz and a 2 solenoid low energy beam line to produce such high intensity beam. The whole injector, equipped with its dedicated diagnostics, has been then installed and tested on the Saclay site. Before shipment from Europe to Japan, acceptance tests have been performed in November 2012 with 100 keV deuteron beam and intensity as high as 140 mA in continuous and pulsed mode. In this paper, the emittance measurements done for different duty cycles and different beam intensities will be presented as well as beam species fraction analysis. Then the reinstallation in Japan and commissioning plan on site will be reported. PMID:24593497

  18. The Romanian experience on testing and quality acceptance criteria of packages used for transportation and storage of low level radioactive wastes

    The transport of radioactive wastes generated by nuclear facilities from non-power applications (research institutes, hospitals, nuclear fuel work) in Romania is one of the important subprogram of Romanian Waste Management Programme and the overall aim is to promote a safe transport and storage (disposal) of the low activity radioactive materials in Romania. After emphasizing the importance of the packaging tests in ensuring that the requisite safety features built into the design of packages comply with the Romanian Nuclear Regulatory Body - National Commission for Nuclear activities Control (NCNAC) requirements and to IAEA's Regulations, the paper presents the type and production testing for type A packages (containers) which have been developed within Institute for Nuclear Research (INR) Pitesti. The paper describes and contains illustrations showing the various tests conducted on the prototype package and how they relate to normal conditions and minor mishaps during transport. Quality assurance and quality acceptance criteria as well as measures taken in order to meet technical specification provided by the design are also presented and commented. The paper concludes that the justification for containment, based on the use of freight container and the pessimistic assessment of potential inhalation doses to those persons involved with the packaging and transport of radwastes, supports the containers as being suitable for classification as an Industrial Type 3 (IP-3). (author)

  19. Trinity Acceptance Tests Performance Summary.

    Rajan, Mahesh [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-12-01

    Ensuring Real Applications perform well on Trinity is key to success. Four components: ASC applications, Sustained System Performance (SSP), Extra-Large MiniApplications problems, and Micro-benchmarks.

  20. SU-E-T-71: Commissioning and Acceptance Testing of a Commercial Monte Carlo Electron Dose Calculation Model (eMC) for TrueBeam

    Purpose: To provide commissioning and acceptance test data of the Varian Eclipse electron Monte Carlo model (eMC v.11) for TrueBeam linac. We also investigated the uncertainties in beam model parameters and dose calculation results for different geometric configurations. Methods: For beam commissioning, PTW CC13 thimble chamber and IBA Blue Phantom2 were used to collect PDD and dose profiles in air. Cone factors were measured with a parallel plate chamber (PTW N23342) in solid water. GafChromic EBT3 films were used for dose calculation verifications to compare with parallel plate chamber results in the following test geometries: oblique incident, extended distance, small cutouts, elongated cutouts, irregular surface, and heterogeneous layers. Results: Four electron energies (6e, 9e, 12e, and 15e) and five cones (6×6, 10×10, 15×15, 20×20, and 25×25) with standard cutouts were calculated for different grid sizes (1, 1.5,2, and 2.5 mm) and compared with chamber measurements. The results showed calculations performed with a coarse grid size underestimated the absolute dose. The underestimation decreased as energy increased. For 6e, the underestimation (max 3.3 %) was greater than the statistical uncertainty level (3%) and was systematically observed for all cone sizes. By using a 1mm grid size, all the calculation results agreed with measurements within 5% for all test configurations. The calculations took 21s and 46s for 6e and 15e (2.5mm grid size) respectively distributed on 4 calculation servants. Conclusion: In general, commissioning the eMC dose calculation model on TrueBeam is straightforward and thedose calculation is in good agreement with measurements for all test cases. Monte Carlo dose calculation provides more accurate results which improves treatment planning quality. However, the normal acceptable grid size (2.5mm) would cause systematic underestimation in absolute dose calculation for lower energies, such as 6e. Users need to be cautious in this

  1. The acceptances and quality control test of the system of thyroid iodine uptake coupled to PC, model DETEC-PC SNR1C-04

    The thyroid iodine uptake is a diagnostic method of great importance in the study and treatment of the thyroid illnesses. The acceptances and quality control test of the system of thyroid iodine uptake coupled to PC, Model DETEC-PC SNR1C-04 manufactured by the CEADEN were made according to the procedures described in the National Manual of Quality Control in Nuclear Medicine Instruments using certified sources of 137Cs, 57Co, 133Ba and 131I, with 5% of uncertainty in the activity value. 670 V was determinate as voltage of work. For the range of energy of 122 keV up to 662 keV the energy linearity had a deviation smaller than 1%. The energy resolution was 13.91% for 131I and 11.12% for 137Cs. The behavior to the activity variation is lineal up to 500 μ Ci (R2 = 0.99) for 131I source to 20 cm of the detector. The maximum count rate was of 34.08 Kc/s. The reproducibility of the system, for 137Cs and 133Ba was smaller than 3%, the losses of count rate in the measurement of the 133Ba using the calibration for 131I was smaller than 2%, for that reason the 133Ba was select like source to made the reproducibility. 131I sources of different activities were measured (simulating patient), determining the experimental uptake and calculating the theoretical values; the absolute differences among these values were between 0.04% and 1.23%. According to obtained values and the system stability the radiometer DETEC-PC SNR1C-04 is accepted for its use like iodine uptake. (Author)

  2. An Introduction to Fuzzy Testing of Multialternative Hypotheses for Group of Samples with the Single Parameter: Through the Fuzzy Confidence Interval of Region of Acceptance

    Manikandan Harikrishnan

    2015-01-01

    Full Text Available Classical statistics and many data mining methods rely on “statistical significance” as a sole criterion for evaluating alternative hypotheses. It is very useful to find out the significant difference existing between the samples as well as the population or between two samples. But in this paper, the researchers try to apply the concepts of fuzzy group testing of hypothesis problem between multi group of samples of same size or different, through comparing the parameters like mean, standard deviation, and so forth. Hence we can compare multigroups such that they have the significant difference in their mean or standard deviation or other parameters through the fuzzy group testing of multihypotheses. The authors introduced and investigated the concepts very first time through fuzzy analysis that can decide which group(s or samples can be taken for further investigation and either H0 is rejected or accepted and hence the next discussion provides the properties of group of samples which may result in the optimized solution for the problem.

  3. Why was Relativity Accepted?

    Brush, S. G.

    Historians of science have published many studies of the reception of Einstein's special and general theories of relativity. Based on a review of these studies, and my own research on the role of the light-bending prediction in the reception of general relativity, I discuss the role of three kinds of reasons for accepting relativity (1) empirical predictions and explanations; (2) social-psychological factors; and (3) aesthetic-mathematical factors. According to the historical studies, acceptance was a three-stage process. First, a few leading scientists adopted the special theory for aesthetic-mathematical reasons. In the second stage, their enthusiastic advocacy persuaded other scientists to work on the theory and apply it to problems currently of interest in atomic physics. The special theory was accepted by many German physicists by 1910 and had begun to attract some interest in other countries. In the third stage, the confirmation of Einstein's light-bending prediction attracted much public attention and forced all physicists to take the general theory of relativity seriously. In addition to light-bending, the explanation of the advance of Mercury's perihelion was considered strong evidence by theoretical physicists. The American astronomers who conducted successful tests of general relativity became defenders of the theory. There is little evidence that relativity was `socially constructed' but its initial acceptance was facilitated by the prestige and resources of its advocates.

  4. Progress of the United States foreign research reactor spent nuclear fuel acceptance program. Reduced enrichment for research and test reactors conference 2002

    Foreign Research Reactor Spent nuclear fuel Acceptance Program is actively working with research reactors to accept eligible material before the Acceptance Policy proper expires in 2006. Reactors/governments wishing to participate should contact US immediately if they have not done so already. Program operations are changing to adapt to new challenges. We continue to promote the importance of this Program to senior management in the Department of Energy

  5. Feasibility and acceptability of home-based management of malaria strategy adapted to Sudan's conditions using artemisinin-based combination therapy and rapid diagnostic test

    Mudather Mahmoud A

    2009-03-01

    Full Text Available Abstract Background Malaria remains a major public health problem especially in sub-Saharan Africa. Despite the efforts exerted to provide effective anti-malarial drugs, still some communities suffer from getting access to these services due to many barriers. This research aimed to assess the feasibility and acceptability of home-based management of malaria (HMM strategy using artemisinin-based combination therapy (ACT for treatment and rapid diagnostic test (RDT for diagnosis. Methods This is a study conducted in 20 villages in Um Adara area, South Kordofan state, Sudan. Two-thirds (66% of the study community were seeking treatment from heath facilities, which were more than 5 km far from their villages with marked inaccessibility during rainy season. Volunteers (one per village were trained on using RDTs for diagnosis and artesunate plus sulphadoxine-pyrimethamine for treating malaria patients, as well as referral of severe and non-malaria cases. A system for supply and monitoring was established based on the rural health centre, which acted as a link between the volunteers and the health system. Advocacy for the policy was done through different tools. Volunteers worked on non-monetary incentives but only a consultation fee of One Sudanese Pound (equivalent to US$0.5. Pre- and post-intervention assessment was done using household survey, focus group discussion with the community leaders, structured interview with the volunteers, and records and reports analysis. Results and discussion The overall adherence of volunteers to the project protocol in treating and referring cases was accepted that was only one of the 20 volunteers did not comply with the study guidelines. Although the use of RDTs seemed to have improved the level of accuracy and trust in the diagnosis, 30% of volunteers did not rely on the negative RDT results when treating fever cases. Almost all (94.7% the volunteers felt that they were satisfied with the spiritual outcome of

  6. Análise da aceitação de aguardentes de cana por testes afetivos e mapa de preferência interno Acceptance evaluation of sugar cane brandy by sensorial affective tests and internal preference map

    Helena Maria André Bolini CARDELLO

    2000-04-01

    ência dos provadores pelas amostras de aguardentes envelhecidas. Os resultados sugerem também que aguardentes envelhecidas por mais de 24 meses em tonel de carvalho de 200L são preferidas pelos consumidores, em detrimento das comerciais não envelhecidas e mesmo das comerciais envelhecidas, que podem ser adicionadas de aguardente não envelhecida (processo denominado corte e também ter correção da cor, conforme permite a Legislação Brasileira. O conteúdo de polifenóis totais e a intensidade de cor também foram determinados, e ambos apresentaram correlação linear positiva significativa (pIn order to compare distincts statistical treatments used in sensorial analysis, the acceptance of 11 sugar cane brandy samples were evaluated by sensorial affective tests, treated by two distints statistical analysis: univariate variance analysis (ANOVA and the multivariate internal preference map (MDPREF. It were analyzed samples stored in a 200 l oak casks during zero, 12, 24, 36 and 48 months and six commercial brands, three of then having the denomination stored and the other three not stored. The samples were evaluated by 100 judges, selected based in a questionary that evaluated affectivity for the product. The sensorial tests conducted in individual cabins were based in a hedonic scale of nine centimeters. The ANOVA and Tukey test and the Internal preference Map (MDPREF, were used to evaluate the obtained data. The ANOVA results showed that the samples stored during 48, 36 and 24 months in the oak cask, presented the higher acceptance scores (scores near 8.0 in the hedonic scale, one commercial brand not stored showed the lowest score, and the others samples showed intermediate acceptance scores. The MDPREF analysis generated in a multidimensional space where the preference data variations were presented in orthogonal axes values, based in the consumers response for each sample. Based on the acceptance data of individual consumers and the vectors of preference, it was

  7. High acceptability of voluntary counselling and HIV-testing but unacceptable loss to follow up in a prevention of mother-to-child HIV transmission programme in rural Malawi: scaling-up requires a different way of acting.

    Manzi, M; Zachariah, R.; Teck, R; Buhendwa, L.; Kazima, J.; Bakali, E; Firmenich, Peter; Humblet, P

    2005-01-01

    SETTING: Thyolo District Hospital, rural Malawi. OBJECTIVES: In a prevention of mother-to-child HIV transmission (PMTCT) programme, to determine: the acceptability of offering 'opt-out' voluntary counselling and HIV-testing (VCT); the progressive loss to follow up of HIV-positive mothers during the antenatal period, at delivery and to the 6-month postnatal visit; and the proportion of missed deliveries in the district. DESIGN: Cohort study. METHODS: Review of routine antenatal, VCT and PMTCT ...

  8. Design of inspection and acceptance test methodology for TIG welded aluminum-alloy bracket for camera housings for IRS-1A space craft and executing it

    Manglik, V. K.; Vaghmare, Rajeev; Shah, A. K.

    1992-10-01

    The Indian Remote Sensing Satellite (IRS) 1A was the first indigenously developed operational remote sensing satellite. The most critical element in the satellite was the remote sensing camera. The camera was mounted on aluminum alloy bracket which was fabricated by TIG welding. The methodology of acceptance and inspection of the TIG welded bracket is presented and discussed. These efforts not only provided the confidence in reliable welded joint but also provided trouble free operation of the camera on board the satellite for its whole life.

  9. Iterative Evaluation in a Mobile Counseling and Testing Program to Reach People of Color at Risk for HIV--New Strategies Improve Program Acceptability, Effectiveness, and Evaluation Capabilities

    Spielberg, Freya; Kurth, Ann; Reidy, William; McKnight, Teka; Dikobe, Wame; Wilson, Charles

    2011-01-01

    This article highlights findings from an evaluation that explored the impact of mobile versus clinic-based testing, rapid versus central-lab based testing, incentives for testing, and the use of a computer counseling program to guide counseling and automate evaluation in a mobile program reaching people of color at risk for HIV. The program's…

  10. Development and testing of two lifestyle interventions for persons with chronic mild-to-moderate traumatic brain injury: Acceptability and feasibility.

    Bay, Esther; Ribbens-Grimm, Christine; Chan, Roxane R

    2016-05-01

    This clinical methods discursive highlights the development, piloting, and evaluation of two group interventions designed for persons who experienced chronic traumatic brain injury (TBI). Intervention science for this population is limited and lacking in rigor. Our innovative approach to customize existing interventions and develop parallel delivery methods guided by Allostatic Load theory is presented and preliminary results described. Overall, parallel group interventions delivered by trained leaders with mental health expertise were acceptable and feasible for persons who reported being depressed, stressed, and symptomatic. They reported being satisfied with the overall programs and mostly satisfied with the individual classes. Attendance was over the anticipated 70% expected rate and changes in daily living habits were reported by participants. These two group interventions show promise in helping persons to self manage their chronic stress and symptomatology. PMID:27091260

  11. ARC Code TI: ACCEPT

    National Aeronautics and Space Administration — ACCEPT consists of an overall software infrastructure framework and two main software components. The software infrastructure framework consists of code written to...

  12. Mistrust in marriage-Reasons why men do not accept couple HIV testing during antenatal care- a qualitative study in eastern Uganda

    Popenoe Rebecca; Namusoko Sarah; Nsabagasani Xavier; Thorson Anna; Larsson Elin C; Ekström Anna

    2010-01-01

    Abstract Background A policy for couple HIV counseling and testing was introduced in 2006 in Uganda, urging pregnant women and their spouses to be HIV tested together during antenatal care (ANC). The policy aims to identify HIV-infected pregnant women to prevent mother-to-child transmission of HIV through prophylactic antiretroviral treatment, to provide counseling, and to link HIV-infected persons to care. However, the uptake of couple testing remains low. This study explores men's views on,...

  13. The Relationship Between Treatment Acceptability and Familism

    Joy R. Pemberton; Joaquin Borrego, Jr.

    2005-01-01

    Many studies have examined the acceptability of treatments for children with disruptive behaviors. However, few studies to date have tested the effects of home environment variables such as family support on treatment acceptability. In the current study, parents’ level of familism was used to predict the ir willingness toaccept several behavioral child treatment techniques. Eighty-two parents completed measures related to familism, child behavior problems, parenting stress, and acceptance of ...

  14. 16 CFR Table 3 to Part 1512 - Minimum Acceptable Values for the Quantity A Defined in the Retroreflective Tire and Rim Test...

    2010-01-01

    ... Defined in the Retroreflective Tire and Rim Test Procedure 3 Table 3 to Part 1512 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES... Retroreflective Tire and Rim Test Procedure Observation angle (degrees) Entrance angle (degrees)...

  15. Acceptable noise level

    Olsen, Steen Østergaard; Nielsen, Lars Holme; Lantz, Johannes;

    2012-01-01

    The acceptable noise level (ANL) is used to quantify the amount of background noise that subjects can accept while listening to speech, and is suggested for prediction of individual hearing-aid use. The aim of this study was to assess the repeatability of the ANL measured in normal-hearing subjects...

  16. The acceptability of the introduction of a type specific herpes antibody screening test into a genitourinary medicine clinic in the United Kingdom

    Mullan, H; Munday, P.

    2003-01-01

    Objective: To determine the uptake of a type specific herpes simplex antibody test if it were offered as part of routine screening in a genitourinary medicine clinic in a district general hospital in the United Kingdom.

  17. Feasibility and acceptability of point of care HIV testing in community outreach and GUM drop-in services in the North West of England: A programmatic evaluation

    Jelliman Pauline; Harrison Ian; Spaine Vida; Coffey Emer; Jones Kathy; Chawla Anu; MacPherson Peter; Phillips-Howard Penelope; Beynon Caryl; Taegtmeyer Miriam

    2011-01-01

    Abstract Background In Liverpool, injecting drug users (IDUs), men-who-have-sex-with-men (MSM) and UK Africans experience a disproportionate burden of HIV, yet services do not reach out to these groups and late presentations continue. We set out to: increase testing uptake in targeted marginalized groups through a community and genitourinary medicine (GUM)-based point of care testing (POCT) programme; and conduct a process evaluation to examine service provider inputs and document service use...

  18. Mistrust in marriage-Reasons why men do not accept couple HIV testing during antenatal care- a qualitative study in eastern Uganda

    Popenoe Rebecca

    2010-12-01

    Full Text Available Abstract Background A policy for couple HIV counseling and testing was introduced in 2006 in Uganda, urging pregnant women and their spouses to be HIV tested together during antenatal care (ANC. The policy aims to identify HIV-infected pregnant women to prevent mother-to-child transmission of HIV through prophylactic antiretroviral treatment, to provide counseling, and to link HIV-infected persons to care. However, the uptake of couple testing remains low. This study explores men's views on, and experiences of couple HIV testing during ANC. Methods The study was conducted at two time points, in 2008 and 2009, in the rural Iganga and Mayuge districts of eastern Uganda. We carried out nine focus group discussions, about 10 participants in each, and in-depth interviews with 13 men, all of whom were fathers. Data were collected in the local language, Lusoga, audio-recorded and thereafter translated and transcribed into English and analyzed using content analysis. Results Men were fully aware of the availability of couple HIV testing, but cited several barriers to their use of these services. The men perceived their marriages as unstable and distrustful, making the idea of couple testing unappealing because of the conflicts it could give rise to. Further, they did not understand why they should be tested if they did not have symptoms. Finally, the perceived stigmatizing nature of HIV care and rude attitudes among health workers at the health facilities led them to view the health facilities providing ANC as unwelcoming. The men in our study had several suggestions for how to improve the current policy: peer sensitization of men, make health facilities less stigmatizing and more male-friendly, train health workers to meet men's needs, and hold discussions between health workers and community members. Conclusions In summary, pursuing couple HIV testing as a main avenue for making men more willing to test and support PMTCT for their wives, does not seem

  19. Program for establishing long-time flight service performance of composite materials in the center wing structure of C-130 aircraft. Phase 4: Ground/flight acceptance tests

    Harvill, W. E.; Kizer, J. A.

    1976-01-01

    The advantageous structural uses of advanced filamentary composites are demonstrated by design, fabrication, and test of three boron-epoxy reinforced C-130 center wing boxes. The advanced development work necessary to support detailed design of a composite reinforced C-130 center wing box was conducted. Activities included the development of a basis for structural design, selection and verification of materials and processes, manufacturing and tooling development, and fabrication and test of full-scale portions of the center wing box. Detailed design drawings, and necessary analytical structural substantiation including static strength, fatigue endurance, flutter, and weight analyses are considered. Some additional component testing was conducted to verify the design for panel buckling, and to evaluate specific local design areas. Development of the cool tool restraint concept was completed, and bonding capabilities were evaluated using full-length skin panel and stringer specimens.

  20. Newbery Medal Acceptance.

    Freedman, Russell

    1988-01-01

    Presents the Newbery Medal acceptance speech of Russell Freedman, writer of children's nonfiction. Discusses the place of nonfiction in the world of children's literature, the evolution of children's biographies, and the author's work on "Lincoln." (ARH)

  1. Analysis of Scrum acceptance

    Vončina, Bojan

    2016-01-01

    The purpose of the thesis was to analyse the acceptance of Scrum methodology, which has become one of the leading agile methodologies, and to find out which were the key factors that influenced the acceptance. The analysis was conducted in Comtrade, which is one of the largest Slovenian software development companies. The First part (theoretical part) contains an introduction chapter, a detailed presentation of Scrum methodology and the presentation of theoretical models, on which practical ...

  2. Acceptability of human risk.

    Kasperson, R.E.

    1983-01-01

    This paper has three objectives: to explore the nature of the problem implicit in the term "risk acceptability," to examine the possible contributions of scientific information to risk standard-setting, and to argue that societal response is best guided by considerations of process rather than formal methods of analysis. Most technological risks are not accepted but are imposed. There is also little reason to expect consensus among individuals on their tolerance of risk. Moreover, debates abo...

  3. Acceptable noise level

    Olsen, Steen Østergaard; Nielsen, Lars Holme; Lantz, Johannes;

    2012-01-01

    The acceptable noise level (ANL) is used to quantify the amount of background noise that subjects can accept while listening to speech, and is suggested for prediction of individual hearing-aid use. The aim of this study was to assess the repeatability of the ANL measured in normal-hearing subjects...... using running Danish and non-semantic speech materials as stimuli and modulated speech-spectrum and multi-talker babble noises as competing stimuli....

  4. Accepting grammars and systems.

    Bordihn, Henning; Fernau, Henning

    2007-01-01

    We investigate several kinds of regulated rewriting (programmed, matrix, with regular control, ordered, and variants thereof) and of parallel rewriting mechanisms (Lindenmayer systems, uniformly limited Lindenmayer systems, limited Lindenmayer systems and scattered context grammars) as accepting devices, in contrast with the usual generating mode. In some cases, accepting mode turns out to be just as powerful as generating mode, e.g. within the grammars of the Chomsky ...

  5. Network Security Acceptance Testing System and Stragety Research of Telecom Operators%电信基础运营商网络安全验收体系及策略探讨

    王渭清; 陈军; 薄明霞

    2011-01-01

    电信基础运营商开放的网络环境、承载的用户信息和现金业务给其带来了大量的网络攻击和入侵隐患。随着安全工作的推进,传统的在线网络和系统的安全防护策略存在许多问题。本文从新建网络和系统工程的安全验收入手,提出了安全验收的体系和策略,并给出了安全验收的主要内容。%Telecom Operators have a widely open network enviroment and carry user information and cash business now.It brings a great deal of network attack and intrusion risk.With the development of network security work,the traditional security protection way,focusing on online network/system,comes out many problems.This article introduces security acceptance testing for new construct of network and system,describes related stragety and system and presents the main content of security acceptance testing.

  6. Sensory acceptance tests of red beet (Beta vulgaris ssp. vulgaris L.), cv. Early Wonder, minimally processed and irradiated; Testes sensoriais de aceitacao da beterraba vermelha (Beta vulgaris ssp. vulgaris L.), cv. Early Wonder, minimamente processada e irradiada

    Hernandes, Nilber Kenup; Vital, Helio de Carvalho, E-mail: nilberkenup@ctex.eb.b [Centro Tecnologico do Exercito (CTEx), Rio de Janeiro, RJ (Brazil). Secao de Defesa Nuclear; Coneglian, Regina Celi Cavestre [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Rio de Janeiro, RJ (Brazil). Inst. de Agronomia. Dept. de Fitotecnia; Godoy, Ronoel Luiz de Oliveira; Freire Junior, Murillo [EMBRAPA Agroindustria de Alimentos, Rio de Janeiro, RJ (Brazil)

    2007-08-15

    Red beet (Early Wonder) was cultivated in an experimental area of the Department of Fitotecnia at the Institute of Agronomy at the Rural Federal University of Rio de Janeiro. After harvest, the roots were minimally processed; packed; exposed to different doses of gamma radiation (0; 0.5; 1.0 and 1.5 kGy) and stored for 20 days at 8.0 deg C. Sensory evaluations were performed 1; 9; 13 and 20 days after irradiation by 12 testers who rated the overall appearance and aroma on a hedonic scale. The results indicated that the irradiated samples remained within the limit of acceptance for 20 days. In addition, the aroma was found to be a more sensitive indicator of the effect of different doses of radiation to the acceptance of the product. (author)

  7. Performance acceptance test of a portable instrument to detect uranium in water at the DOE Advanced Waste Water Treatment Plant, Fernald, Ohio

    The Eppendorf-Biotronik Model IC 2001-2, a portable field ruggedized ion chromatography instrument, was rigorously tested at the DOE Advanced Waste Water Treatment Plant, Fernald, Ohio. This instrument rapidly detected the uranium concentration in water, and has a detection limit in the low ppb range without using the sample concentrating feature. The test set of samples analyzed included: ''Real World'' water samples from the AWWT containing uranium concentrations in the 9--110 ppb range, a sample blank, and a performance evaluation sample. The AWWT samples contained sets of both raw water and acid-preserved water samples. Selected samples were analyzed in quadruplicate to asses the instrument's precision, and these results were compared with the results from an off-site confirmatory laboratory to assess the instrument's accuracy. Additional comparisons with on-site laboratory instruments, Chemcheck KPA-11 and Scintrex UA-3 are reported. Overall, the Eppendorf-Biotronik IC 2001-2 performed exceptionally well providing a detection limit in the low ppb region (< 10 ppb) and giving rapid (< 5 minutes) accurate and reproducible analytical results for the AWWT, ''real world'', water samples with uranium concentrations in the region of interest (10--40 ppb). The per sample operating cost for this instrument is equivalent to the per sample cost for the currently used KPA. The time required to analyze a sample and provide a result is approximately the same for the CI 2001-2, KPA, and Scintrex instruments

  8. Protocol for stage 1 of the GaP study (Genetic testing acceptability for Paget's disease of bone: an interview study about genetic testing and preventive treatment: would relatives of people with Paget's disease want testing and treatment if they were available?

    Marteau Theresa M

    2006-06-01

    Full Text Available Abstract Background Paget's disease of bone (PDB is characterised by focal increases in bone turnover, affecting one or more bones throughout the skeleton. This disrupts normal bone architecture and causes pain, deformity, deafness, osteoarthritis, and fractures. Genetic factors are recognised to play a role in PDB and it is now possible to carry out genetic tests for research. In view of this, it is timely to investigate the clinical potential for a programme of genetic testing and preventative treatment for people who have a family history of PDB, to prevent or delay the development of PDB. Evidence from non-genetic conditions, that have effective treatments, demonstrates that patients' beliefs may affect the acceptability and uptake of treatment. Two groups of beliefs (illness and treatment representations are likely to be influential. Illness representations describe how people see their illness, as outlined in Leventhal's Self-Regulation Model. Treatment representations describe how people perceive potential treatment for their disease. People offered a programme of genetic testing and treatment will develop their own treatment representations based on what is offered, but the beliefs rather than the objective programme of treatment are likely to determine their willingness to participate. The Theory of Planned Behaviour is a theoretical model that predicts behaviours from people's beliefs about the consequences, social pressures and perceived control over the behaviour, including uptake of treatment. Methods/design This study aims to examine the acceptability of genetic testing, followed by preventative treatment, to relatives of people with PDB. We aim to interview people with Paget's disease, and their families, from the UK. Our research questions are: 1. What do individuals with Paget's disease think would influence the involvement of their relatives in a programme of genetic testing and preventative treatment? 2. What do relatives of

  9. Spain accepts safeguards controls

    Spain became the 26th country to accept safeguards controls by the Agency in December. An agreement was signed in Vienna, transferring to IAEA the administration of safeguards against diversion of materials and installations to military purposes provided for under a nuclear co-operation agreement concluded between Spain and USA in 1957

  10. Robustness - acceptance criteria

    Rizzuto, Enrico; Sørensen, John Dalsgaard; Kroon, Inger B.

    2010-01-01

    This factsheet describes the general framework on the bases of which acceptance criteria for requirements on the robustness of structures can be set. Such framework is based on the more general concept of risk-based assessment of engineering systems. The present factsheet is to be seen in...

  11. Approaches to acceptable risk

    Several alternative approaches to address the question open-quotes How safe is safe enough?close quotes are reviewed and an attempt is made to apply the reasoning behind these approaches to the issue of acceptability of radiation exposures received in space. The approaches to the issue of the acceptability of technological risk described here are primarily analytical, and are drawn from examples in the management of environmental health risks. These include risk-based approaches, in which specific quantitative risk targets determine the acceptability of an activity, and cost-benefit and decision analysis, which generally focus on the estimation and evaluation of risks, benefits and costs, in a framework that balances these factors against each other. These analytical methods tend by their quantitative nature to emphasize the magnitude of risks, costs and alternatives, and to downplay other factors, especially those that are not easily expressed in quantitative terms, that affect acceptance or rejection of risk. Such other factors include the issues of risk perceptions and how and by whom risk decisions are made

  12. Approaches to acceptable risk

    Whipple, C.

    1997-04-30

    Several alternative approaches to address the question {open_quotes}How safe is safe enough?{close_quotes} are reviewed and an attempt is made to apply the reasoning behind these approaches to the issue of acceptability of radiation exposures received in space. The approaches to the issue of the acceptability of technological risk described here are primarily analytical, and are drawn from examples in the management of environmental health risks. These include risk-based approaches, in which specific quantitative risk targets determine the acceptability of an activity, and cost-benefit and decision analysis, which generally focus on the estimation and evaluation of risks, benefits and costs, in a framework that balances these factors against each other. These analytical methods tend by their quantitative nature to emphasize the magnitude of risks, costs and alternatives, and to downplay other factors, especially those that are not easily expressed in quantitative terms, that affect acceptance or rejection of risk. Such other factors include the issues of risk perceptions and how and by whom risk decisions are made.

  13. 1984 Newbery Acceptance Speech.

    Cleary, Beverly

    1984-01-01

    This acceptance speech for an award honoring "Dear Mr. Henshaw," a book about feelings of a lonely child of divorce intended for eight-, nine-, and ten-year-olds, highlights children's letters to author. Changes in society that affect children, the inception of "Dear Mr. Henshaw," and children's reactions to books are highlighted. (EJS)

  14. Den betingede accept

    Kolind, Torsten

    1999-01-01

    difficulties in underscoring this normality. This conditioned accept tends to leave the ex-prisoner in an vacuum of signification; he is neither fully normal nor fully deviant. In regard to identity, this vacuum, and the practices that follows, leaves the ex-prisoner badly equipped in his attempt to live up to...

  15. Nota científica: teste de aceitação de bebida mista de soja e amora Scientific note: acceptance test of a mixed soybean and mulberry drink

    Maíra Rodrigues Uliana

    2012-06-01

    Full Text Available O objetivo deste trabalho consistiu em elaborar e avaliar a aceitação de bebida mista de extrato hidrossolúvel de soja (EHS e suco de amora (SA. As bebidas, produzidas com diferentes proporções de EHS e SA (1:1; 1:1,5; 1:2 m/m, e diferentes concentrações de sólidos solúveis (10, 12 e 14 °Brix, foram analisadas sensorialmente e seus resultados foram submetidos à análise de variância e regressão. As diferentes proporções de EHS e SA nas bebidas produzidas interferiram no aroma e na aparência das bebidas; porém, não existiu uma relação direta entre essas proporções e a aceitabilidade desses atributos. O teor de sólidos solúveis, entretanto, influenciou o sabor e a impressão global. A preferência dos provadores, tanto no sabor como na impressão global, recaiu nas bebidas mais doces, havendo uma relação direta entre o teor de açúcar e a aceitação. Todas as bebidas formuladas foram aprovadas pela equipe de provadores.The purpose of this study was to prepare and evaluate the acceptability of a mixed hydrosoluble soybean extract (EHS and mulberry juice (SA drink. The drinks, made with different proportions of EHS and SA (1:1, 1:1.5 and 1:2 w/w and different concentrations of soluble solids (10, 12 and 14 °Brix, were analyzed by a sensory evaluation and the results submitted to an analysis of variance and regression. The different proportions of EHS and SA interfered in the beverage aroma and appearance, but there was no direct relationship between these proportions and acceptability of the attributes. However, the soluble solids content affected the taste and overall impression. The preference of the panellists, both with respect to flavour and overall impression, was for the sweeter drinks, and there was a direct relationship between the sugar content and acceptance. All the beverages were approved by the panellists.

  16. Differences in HIV vaccine acceptability between genders.

    Kakinami, Lisa; Newman, Peter A; Lee, Sung-Jae; Duan, Naihua

    2008-05-01

    The development of safe and efficacious preventive HIV vaccines offers the best long-term hope of controlling the AIDS pandemic. Nevertheless, suboptimal uptake of safe and efficacious vaccines that already exist suggest that HIV vaccine acceptability cannot be assumed, particularly among communities most vulnerable to HIV. The present study aimed to identify barriers and motivators to future HIV vaccine acceptability among low socioeconomic, ethnically diverse men and women in Los Angeles County. Participants completed a cross-sectional survey assessing their attitudes and beliefs regarding future HIV vaccines. Hypothetical HIV vaccine scenarios were administered to determine HIV vaccine acceptability. Two-sided t-tests were performed, stratified by gender, to examine the association between vaccine acceptability and potential barriers and motivators. Barriers to HIV vaccine acceptability differed between men and women. For women, barriers to HIV vaccine acceptability were related to their intimate relationships (pnegative experiences with health care providers (pGender-specific interventions may increase vaccine acceptability among men and women at elevated risk for HIV infection. Among women, interventions need to focus on addressing barriers due to gendered power dynamics in relationships and discrimination in health care. Among men, education that addresses fears and misconceptions about adverse effects of HIV vaccination on health and the importance of vaccination as one component of integrated HIV prevention may increase vaccine acceptability. PMID:18484322

  17. Development of a Weight Loss Mobile App Linked With an Accelerometer for Use in the Clinic: Usability, Acceptability, and Early Testing of its Impact on the Patient-Doctor Relationship

    Choo, Seryung; Jung, Se Young; Kim, Sarah; Kim, Jeong Eun; Han, Jong Soo; Kim, Sohye; Kim, Jeong Hyun; Kim, Jeehye; Kim, Yongseok; Kim, Dongouk; Steinhubl, Steve

    2016-01-01

    Background Although complications of obesity are well acknowledged and managed by clinicians, management of obesity itself is often difficult, which leads to its underdiagnosis and undertreatment in hospital settings. However, tools that could improve the management of obesity, including self-monitoring, engagement with a social network, and open channels of communication between the patient and doctor, are limited in a clinic-based setting. Objective The objective of our study was to evaluate the usability and acceptability of a newly developed mobile app linked with an accelerometer and its early effects on patient-doctor relationships. Methods From September 2013 to February 2014, we developed a mobile app linked with an accelerometer as a supportive tool for a clinic-based weight loss program. The app used information from electronic health records and delivered tailored educational material. Personal goal setting, as well as monitoring of weight changes and physical activity combined with feedback, are key features of the app. We also incorporated an interactive message board for patients and doctors. During the period of March 2014 to May 2014, we tested our mobile app for 1 month in participants in a hospital clinic setting. We assessed the app’s usability and acceptability, as well as the patient-doctor relationship, via questionnaires and analysis of app usage data. Results We recruited 30 individuals (18 male and 12 female) for the study. The median number of log-ins per day was 1.21, with the most frequently requested item being setting goals, followed by track physical activities and view personal health status. Scales of the depth of the patient-doctor relationship decreased from 27.6 (SD 4.8) to 25.1 (SD 4.5) by a Wilcoxon signed rank test (P=.02). Conclusions A mobile phone app linked with an accelerometer for a clinic-based weight loss program is useful and acceptable for weight management but exhibited less favorable early effects on patient

  18. The Acceptability of Speech with Radio Interference

    Baykaner, K.; Hummersone, H.; Mason, R.;

    2014-01-01

    A listening test was conducted to investigate the acceptability of audio-on-audio interference for radio programs featuring speech as the target. Twenty-one subjects, including naïve and expert listeners, were presented with 200 randomly assigned pairs of stimuli and asked to report, for each trial......, whether the listening scenario was acceptable or unacceptable. Stimuli pairs were set to randomly selected SNRs ranging from 0 to 45 dB. Results showed no significant difference between subjects according to listening experience. A logistic regression to acceptability was carried out based on SNR. The...

  19. Acceptance of Tinnitus : Validation of the Tinnitus Acceptance Questionnaire

    Weise, Cornelia; Kleinstäuber, Maria; Hesser, Hugo; Westin, Vendela; Andersson, Gerhard

    2013-01-01

    The concept of acceptance has recently received growing attention within tinnitus research due to the fact that tinnitus acceptance is one of the major targets of psychotherapeutic treatments. Accordingly, acceptance-based treatments will most likely be increasingly offered to tinnitus patients and assessments of acceptance-related behaviours will thus be needed. The current study investigated the factorial structure of the Tinnitus Acceptance Questionnaire (TAQ) and the role of tinnitus acce...

  20. Schematic effects of rape myth acceptance

    Süssenbach, Philipp

    2011-01-01

    In a set of studies, the present work investigates the type of influence exerted by rape myth acceptance (RMA). Rape myths may be defined as "beliefs about rape (i.e., about its causes, context, consequences, perpetrators, victims, and their interaction) that serve to deny, downplay or justify male sexual aggression against women" (Gerger, Kley, Bohner, & Siebler, 2007, p. 423). In this work the hypothesis is made and tested that the acceptance of rape myths influences the processing of relev...

  1. A structural model of technology acceptance

    Etienne Erasmus; Sebastiaan Rothmann; Chrizanne van Eeden

    2015-01-01

    Orientation: Enterprise resource systems have not always led to significant organisational enhancement and many projects in which these systems have been implemented turn out to be over budget, not on time and unsuccessful.Research purpose: The aim of this study was to test the technology acceptance model within a South African SAP® Enterprise Resource Planning user environment.Motivation for the study: No study could be traced in which the technology acceptance model has been evaluated in th...

  2. Waste acceptance and logistics

    There are three major components which are normally highlighted when the Civilian Radioactive Waste Management Program is discussed - the repository, the monitored retrievable storage facility, and the transportation system. These are clearly the major physical system elements and they receive the greatest external attention. However, there will not be a successful, operative waste management system without fully operational waste acceptance plans and logistics arrangements. This paper will discuss the importance of developing, on a parallel basis to the normally considered waste management system elements, the waste acceptance and logistics arrangements to enable the timely transfer of spent nuclear fuel from more than one hundred and twenty waste generators to the Federal government. The paper will also describe the specific activities the Program has underway to make the necessary arrangements. (author)

  3. Shielded canister transporter equipment acceptance test operations

    The defense waste processing facility (DWPF) processes high level waste at the Savannah River Plant (SRP) by vitrifying the waste and placing it in stainless stell canisters for long term storage. The shielded canister transporter (SCT) is a diesel powered mobile rubber tired self-propelled vehicle which transports the canisters from the DWPF processing facility to the on-site waste storage building. The SCT has a system of automatic programmable logic controls (PLC) which provides operational handling control with a shielded transfer cask and associated canister positional equipment

  4. Two-stage sampling for acceptance testing

    Atwood, C.L.; Bryan, M.F.

    1992-09-01

    Sometimes a regulatory requirement or a quality-assurance procedure sets an allowed maximum on a confidence limit for a mean. If the sample mean of the measurements is below the allowed maximum, but the confidence limit is above it, a very widespread practice is to increase the sample size and recalculate the confidence bound. The confidence level of this two-stage procedure is rarely found correctly, but instead is typically taken to be the nominal confidence level, found as if the final sample size had been specified in advance. In typical settings, the correct nominal [alpha] should be between the desired P(Type I error) and half that value. This note gives tables for the correct a to use, some plots of power curves, and an example of correct two-stage sampling.

  5. Two-stage sampling for acceptance testing

    Atwood, C.L.; Bryan, M.F.

    1992-09-01

    Sometimes a regulatory requirement or a quality-assurance procedure sets an allowed maximum on a confidence limit for a mean. If the sample mean of the measurements is below the allowed maximum, but the confidence limit is above it, a very widespread practice is to increase the sample size and recalculate the confidence bound. The confidence level of this two-stage procedure is rarely found correctly, but instead is typically taken to be the nominal confidence level, found as if the final sample size had been specified in advance. In typical settings, the correct nominal {alpha} should be between the desired P(Type I error) and half that value. This note gives tables for the correct a to use, some plots of power curves, and an example of correct two-stage sampling.

  6. kitchingroup-57: Accepted

    John Kitchin

    2016-01-01

    This is the accepted version of this manuscript. @article{kitchin-2015-examp, author = {Kitchin, John R.}, title = {Examples of Effective Data Sharing in Scientific Publishing}, journal = {ACS Catalysis}, volume = {5}, number = {6}, pages = {3894-3899}, year = 2015, doi = {10.1021/acscatal.5b00538}, url = { http://dx.doi.org/10.1021/acscatal.5b00538 }, keywords = {DESC0004031, early-career, orgmode, Data sharing }, eprint = { http://dx.doi.org/10.1021/acscatal.5b00538 }, }

  7. Environment and public acceptance

    The problems involved in the siting of nuclear power stations at a local level are of a political economic, social or ecological order. The acceptance of a nuclear station mostly depends on its interest for the local population. In order to avoid negative reactions, the men who are responsible must make the harmonious integration of the station within the existing economic and social context their first priority

  8. Age and Acceptance of Euthanasia.

    Ward, Russell A.

    1980-01-01

    Study explores relationship between age (and sex and race) and acceptance of euthanasia. Women and non-Whites were less accepting because of religiosity. Among older people less acceptance was attributable to their lesser education and greater religiosity. Results suggest that quality of life in old age affects acceptability of euthanasia. (Author)

  9. KOMPOSISI GIZI DAN DAYA TERIMA MAKANAN TERAPI: READY TO USE THERAPEUTIC FOOD UNTUK BALITA GIZI BURUK (NUTRITION COMPOSITION AND ACCEPTANCE TEST OF READY TO USE THERAPEUTIC FOOD FOR SEVERE MALNOURISHED CHILDREN

    Komari Komari

    2012-12-01

    Full Text Available Abstract Severe malnourished children need special diet which is nutritious, easily digested, and safe to improve their nutritional status. The diet could be Ready-to-Use Therapeutic Food (RUTF, composed by highly digestible component such as milk, vegetable oil, sugar, vitamines, minerals, and indigenous food such as peanut, mungbean and tempeh powder. This study was aimed to examine the nutrients content and the sensory quality of local RUTF. The method utilised were acceptability test on severe malnourished children, chemical analyses to identify nutrient content and safety analysis towards microbial and heavy metal contaminants. The  results showed that RUTF contained energy ranging from 521 kcal /100 g to 530 kcal/100 g, and protein ranging from 14,1 g/100 g to 16,9 g/100g. The RUTF was acceptable by malnourished children under five years old. Keywords: ready to use, therapeutic food, malnourished Abstrak Anak gizi buruk memerlukan diet yang khusus untuk meningkatkan status gizinya dengan makanan yang mudah dicerna, bergizi tinggi dan aman. Makanan tersebut dapat berupa Ready to Use Therapeutic Food (RUTF yang terdiri dari bahan yang mudah dicerna seperti susu, minyak sayur, gula, vitamin dan mineral, dan menggunakan bahan makanan lokal yakni tepung kacang tanah, kacang hijau, dan tempe. Penelitian ini bertujuan menilai komposisi zat gizi dan kualitas sensori produk RUTF lokal. Metode yang digunakan adalah uji daya terima yang dilakukan terhadap anak balita gizi buruk, uji kimia untuk mengukur komposisi gizi dan keamanan terhadap mikroba dan logam berat. Hasil menunjukkan bahwa komposisi gizi untuk RUTF mengandung cukup tinggi energi  yaitu berkisar antara 521-530 kkal/100g dan protein berkisar antara 14,1-16,9 g/100g. Makanan tersebut juga dapat diterima oleh  anak-anak balita gizi buruk. [Penel Gizi Makan 2012, 35(2: 159-167] Kata Kunci: ready to use, makanan terapi, gizi buruk

  10. Understanding social acceptance of electricity generation sources

    Social acceptability is a determinant factor in the failure or success of the government's decisions about which electricity generation sources will satisfy the growing demand for energy. The main goal of this study was to validate a causal trust-acceptability model for electricity generation sources. In the model, social acceptance of an energy source is directly caused by perceived risk and benefit and also by social trust in regulatory agencies (both directly and indirectly, through perceived risk and benefit). Results from a web-based survey of Chilean university students demonstrated that data for energy sources that are controversial in Chilean society (fossil fuels, hydro, and nuclear power) fit the hypothesized model, whereas data for non conventional renewable energy sources (solar, wind, geothermal and tidal) did not. Perceived benefit had the greatest total effect on acceptability, thus emerging as a key predictive factor of social acceptability of controversial electricity generation sources. Further implications for regulatory agencies are discussed. - Highlights: ► We tested a causal trust-acceptability model for electricity generation sources in Chile. ► Data for controversial energy sources in the Chilean society (fossil fuels, hydro and nuclear power) fit the hypothesized model. ► Data for non conventional renewable energy sources did not fit the data. ► Perceived benefit showed the greatest total effect on acceptability.

  11. Acceptance, Tolerance, Participation

    The problem of radioactive waste management from an ethical and societal viewpoint was treated in this seminar, which had participants from universities (social, theological, philosophical and science institutes), waste management industry, and regulatory and controlling authorities. After initial reviews on repository technology, policies and schedules, knowledge gaps, and ethical aspects on decision making under uncertainty, four subjects were treated in lectures and discussions: Democratic collective responsibility, Handling threats in democratic decision making, Waste management - a technological operation with a social dimension, Acceptance and legitimity. Lectures with comments and discussions are collected in this report

  12. Marketing for Acceptance

    Tina L. Johnston, Ph.D.

    2009-11-01

    Full Text Available Becoming a researcher comes with the credentializing pressure to publish articles in peer-reviewed journals (Glaser, 1992; Glaser, 2007; Glaser, 2008. The work intensive process is exacerbated when the author’s research method is grounded theory. This study investigated the concerns of early and experienced grounded theorists to discover how they worked towards publishing research projects that applied grounded theory as a methodology. The result was a grounded theory of marketing for acceptance that provides the reader with insight into ways that classic grounded theorists have published their works. This is followed by a discussion of ideas for normalizing classic grounded theory research methods in our substantive fields.

  13. High acceptance recoil polarimeter

    In order to detect neutrons and protons in the 50 to 600 MeV energy range and measure their polarization, an efficient, low-noise, self-calibrating device is being designed. This detector, known as the High Acceptance Recoil Polarimeter (HARP), is based on the recoil principle of proton detection from np→n'p' or pp→p'p' scattering (detected particles are underlined) which intrinsically yields polarization information on the incoming particle. HARP will be commissioned to carry out experiments in 1994

  14. Morsleben waste acceptance requirements

    The Morsleben waste acceptance requirements take into account the valid stipulations in the permanent operational license of the Morsleben repository for radioactive waste (Eram) dated April 22, 1986, and in the documents underlying it. In line with the guaranteed continued validity until June 30, 2000 of this permanent operational license, also the classification of radioactive waste by waste types (A) and radiation protection groups (S) was retained. The revised requirements to be met by radioactive waste to be disposed of in Eram as issued by the German Federal Office for Radiation Protection (BfS) effective August 1996 constitute the safety framework which must be adhered to by this waste. They also take into account other stipulations by the BfS, especially voluntary restrictions and conditions imposed by the self-surveillance. Eram accepts the 'solid waste' and 'spent sealed radiation sources' categories. The waste generators must observe the requirements to be met by waste to be stored permanently. In the case of solid waste, these conditions include criteria to be met by waste forms, activity limitations for radionuclides and groups of radionuclides, and packaging criteria. (orig.)

  15. Heat exchanger staybolt acceptance criteria

    The structural integrity demonstration of the primary coolant piping system includes evaluating the structural capacity of each component against a large break or equivalent Double-Ended Guillotine Break. A large break at the inlet or outlet heads of the heat exchangers would occur if the restraint members of the heads become inactive. The structural integrity of the heads is demonstrated by showing the redundant capacity of the staybolts to restrain the head at design conditions and under seismic loadings. The Savannah River Site heat exchanger head is attached to the tubesheet by 84 staybolts. Access to the staybolts is limited due to a welded seal cap over the staybolts. An ultrasonic testing (UT) inspection technique to provide an in-situ examination of the staybolts has recently been developed at SRS. Examination of the staybolts will be performed to ensure their service condition and configuration is within acceptance limits. An acceptance criteria methodology has been developed to disposition flaws reported in the staybolt inspections while ensuring adequate restraint capacity of the staybolts to maintain integrity of the heat exchanger heads against collapse. The methodology includes an approach for the baseline and periodic inspections of the staybolts. The heat exchanger head is analyzed with a three-dimensional finite element model. The restraint provided by the staybolts is evaluated for several postulated cases of inactive or missing staybolts. Evaluation of specific, inactive staybolt configurations based on the UT results can be performed with the finite element model and fracture methodology in this report

  16. Is nuclear power acceptable

    The energy shortage forecast for the early 21st century is considered. Possible energy sources other than fossil fuel are stated as geothermal, fusion, solar and fission, of which only fission has been demonstrated technically and economically. The environmental impacts of fission are examined. The hazards are discussed under the following headings: nuclear accident, fatality risk, safe reactor, property damage, acts of God, low-level release of radioactivity, diversion of fissile material and sabotage, radioactive waste disposal, toxicity of plutonium. The public reaction to nuclear power is analyzed, and proposals are made for a programme of safety and security which the author hopes will make it acceptable as the ultimate energy source. (U.K.)

  17. Public acceptance of nuclear power

    The lecture addresses the question why we need public acceptance work and provides some clues to it. It explains various human behaviour patterns which determine the basics for public acceptance. To some extent, the opposition to nuclear energy and the role the media play are described. Public acceptance efforts of industry are critically reviewed. Some hints on difficulties with polling are provided. The lecture concludes with recommendations for further public acceptance work. (author)

  18. The development and equivalence analysis of mandarin acceptable noise level test materials%普通话可接受噪声级测试材料的开发与等价性评估

    陈建勇; 张华; 陈静; 陈雪清; 郭连生; 曹文; 吴燕君; 李玉玲

    2011-01-01

    目的 开发普通话版可接受噪声级(acceptable noise level,ANL)测试材料.方法 从小学、初中和高中语文教材中选取3篇难易程度不同的短文材料;选取31例听力言语正常人分别进行3种材料的ANL测试,获得3种材料下的最舒适响度级(most comfortable loudness,MCL)、最大背景噪声级(background noise level,BNL)和ANL值.结果 听力正常人群个体问ANL值存在很大差异(F=22.414,P<0.05),变化范围从-1~21 dB HL不等;但3组测试材料的MCL、BNL和ANL值均无统计学差异.相关分析结果显示,3组材料间MCL与ANL的相关性依次为:,r=0.532,P=0.002; ,r=0.474,P=0.007; ,r=0.530,P=0.002.结论 ANL值不受测试材料的影响,可利用不同性质的材料进行ANL测试,便于临床该项测试的开展和应用:初步选取相关性较好且较易理解的作为普通话ANL正式测试材料,用于助听器选配和人工耳蜗植入效果的评估.%OBJECTIVE To develop the mandarin test material of acceptable noise level (ANL) .METHODS ANL tests were measured for 31 normal hearing participants using the different intelligible materials. For each discourse, the most comfortable loudness (MCL) and background noise level (BNL)were found. The ANL was then computed by subtracting the mean BNL from MCL. RESULTS Statistic analysis indicated that there were significant differences of the ANL (P< 0.05) among the normal hearing listeners,but no differences of the three materials' MCL, BNL, and ANL were found. The Pearson correlation coefficients between MCL-ANL showed that "The Spring Festival of Beijing" had much better correlation than the other two discourses. CONCLUSION ANL may not change as speech intelligibility changes and can be measured using various types of speech signals; "The Spring Festival of Beijing" will be used as the mandarin ANL test material to evaluate the outcomes of hearing aid fitting and cochlear implantation.

  19. Public acceptance of biofuels

    The public acceptance of biofuels in Greece is examined in this work. The analysis of 571 face to face interviews shows that 90.7% of the respondents believe that climatic changes are related to fossil fuel consumption, while only 23.8% know the difference between biodiesel and bioethanol. 76.1% believe that energy saving should precede the use of an alternative source of energy. Only 27.3% believe that priority must be given to biofuels over other renewable energy sources. Only 49.9% think that the use of biofuels can be an effective solution against climatic changes and 53.9% believe that the use of biofuels can be an effective solution for the energy problem. Finally, 80.9% of the car owners are willing to use biofuels, 44.8% are willing to pay the supplementary amount of 0.06 Euro /L of the fuel market price, while the average amount reported as willing to pay was 0.079 Euro /L on top of the fuel market price. Furthermore, eight models correlating the eight main responses with several socioeconomic variables are developed and analyzed. Those findings heave important policy implications related to the use and promotion of biofuels.

  20. Public acceptance of biofuels

    Savvanidou, Electra; Zervas, Efthimios; Tsagarakis, Konstantinos P. [Department of Environmental Engineering, Democritus University of Thrace, Vas. Sofias 12, 67100 Xanthi (Greece)

    2010-07-15

    The public acceptance of biofuels in Greece is examined in this work. The analysis of 571 face to face interviews shows that 90.7% of the respondents believe that climatic changes are related to fossil fuel consumption, while only 23.8% know the difference between biodiesel and bioethanol. 76.1% believe that energy saving should precede the use of an alternative source of energy. Only 27.3% believe that priority must be given to biofuels over other renewable energy sources. Only 49.9% think that the use of biofuels can be an effective solution against climatic changes and 53.9% believe that the use of biofuels can be an effective solution for the energy problem. Finally, 80.9% of the car owners are willing to use biofuels, 44.8% are willing to pay the supplementary amount of 0.06 EUR/L of the fuel market price, while the average amount reported as willing to pay was 0.079 EUR/L on top of the fuel market price. Furthermore, eight models correlating the eight main responses with several socioeconomic variables are developed and analyzed. Those findings heave important policy implications related to the use and promotion of biofuels. (author)

  1. Calculation of gas temperature at the outlet of the combustion chamber and in the air-gas channel of a gas-turbine unit by data of acceptance tests in accordance with ISO

    Kostyuk, A. G.; Karpunin, A. P.

    2016-01-01

    This article describes a high accuracy method enabling performance of the calculation of real values of the initial temperature of a gas turbine unit (GTU), i.e., the gas temperature at the outlet of the combustion chamber, in a situation where manufacturers do not disclose this information. The features of the definition of the initial temperature of the GTU according to ISO standards were analyzed. It is noted that the true temperatures for high-temperature GTUs is significantly higher than values determined according to ISO standards. A computational procedure for the determination of gas temperatures in the air-gas channel of the gas turbine and cooling air consumptions over blade rims is proposed. As starting equations, the heat balance equation and the flow mixing equation for the combustion chamber are assumed. Results of acceptance GTU tests according to ISO standards and statistical dependencies of required cooling air consumptions on the gas temperature and the blade metal are also used for calculations. An example of the calculation is given for one of the units. Using a developed computer program, the temperatures in the air-gas channel of certain GTUs are calculated, taking into account their design features. These calculations are performed on the previously published procedure for the detailed calculation of the cooled gas turbine subject to additional losses arising because of the presence of the cooling system. The accuracy of calculations by the computer program is confirmed by conducting verification calculations for the GTU of the Mitsubishi Comp. and comparing results with published data of the company. Calculation data for temperatures were compared with the experimental data and the characteristics of the GTU, and the error of the proposed method is estimated.

  2. Comparison of acceptability of tropical fruit mixed nectars by mean test and multivariate statistical analysisComparação da aceitabilidade de néctares mistos de frutas tropicais por teste de médias e análise estatística multivariada

    Paulo Henrique Machado Sousa

    2013-10-01

    Full Text Available Fruits are a rich source of nutrients and fruit juices are a popular way of consuming them. Development of mixed juices, where two or more fruit juices are blended to obtain a product that combines the nutritional value of fruits, has been encouraged by the food industry and well accepted by consumers. This work aimed to develop mixed nectars of tropical fruits (cashew apple, mango and acerola and to compare the acceptability data by mean test and multivariate statistical analysis of hierarchic grouping and principal compounds. The tropical fruit nectars showed good acceptability, the formulations with higher mango and cashew and lower acerola contents the most accepted. The formulation with 12.25% cashew apple pulp, 21% mango pulp and 1.75% acerola pulp had the highest global evaluation score. However, it could be observed by the cluster analysis of consumers’ data and posterior principal components analysis of these results a clearly segmentation of consumers. As frutas são fontes ricas de nutrientes e os sucos de frutas são formas mais populares de consumi-las. O desenvolvimento de sucos mistos, em que duas ou mais frutas são misturadas para se obter um produto que combina o valor nutricional das frutas, tem sido estimulado pela indústria de alimentos e bem aceita pelos consumidores. Este trabalho teve como objetivo desenvolver néctares mistos de frutas tropicais (caju, manga e acerola e comparar os dados de aceitabilidade por teste de média e análises estatísticas multivariadas de agrupamento hierárquico e componentes principais. O resultado do teste de médias indicou uma maior aceitação para os néctares com maiores teores de manga e caju e menores teores de acerola. A formulação contendo 12,25% de polpa de caju, 21% de polpa de manga e 1,75% de polpa de acerola teve o maior escore na avaliação global. No entanto, pode ser observado pela análise de cluster de dados dos consumidores e posterior análise de componentes

  3. Analysis on visual acceptance tests of the turbine model for the Three Gorges Project%三峡水轮机模型目击验收试验剖析

    黄源芳; 熊腾晖; 田子勤

    2001-01-01

    The turbine for the Three Gorges Project is one of the mixed-flow turbines with great changes of operation water head. Its appearance dimensions and weight also rank the first in the current mixed-flow turbines. The operation stability of the generating units for the Three Gorges Project always is the key focused by the designer, scientific research institute, manufacturer and user. The results of visual acceptance tests showed that its comprehensive energy performances and cavitation characteristics basically meet the requirements of the Contract. The optimum efficiency of its model is 94.54% (guaranteed value is 94.51%), the rated efficiency 89.53% (guaranteed value 87.85%), and the weighted average efficiency without surplus water season 92.29% (guaranteed value 92.16%). Because of various reasons, the stability indexes could not meet the guaranteed value required by the Contract so that the manufacturer is required to optimize the design of sluice taper and make other tests.%三峡电站水轮机是运行水头变幅最大的混流式水轮机之一,其外形尺寸和重量亦是当前混流式水轮机之最。三峡机组的运行稳定性始终是设计、科研、制造和使用部门关注的首要课题。目击验收试验的结果表明,综合能量特性和空化特性基本上满足了合同要求,其模型最优效率为94.54%(保证值为94.51%);额定效率为89.53 %(保证值为87.85%);无弃水期加权平均效率为92.29%(保证值为92.16%)。由于各种原因,稳定性指标未能全面达到合同保证值。

  4. FFTBM and primary pressure acceptance criterion

    When thermalhydraulic computer codes are used for simulation in the area of nuclear engineering the question is how to conduct an objective comparison between the code calculation and measured data. To answer this the fast Fourier transform based method (FFTBM) was developed. When the FFTBM method was developed the acceptance criteria for primary pressure and total accuracy were set. In the recent study the FFTBM method was used for accuracy quantification of RD-14M large LOCA test B9401 calculations. The blind accuracy analysis indicated good total accuracy while the primary pressure criterion was not fulfilled. The objective of the study was therefore to investigate the reasons for not fulfilling the primary pressure acceptance criterion and the applicability of the criterion to experimental facilities simulating heavy water reactor. The results of the open quantitative analysis showed that sensitivity analysis for influence parameters provide sufficient information to judge in which calculation the accuracy of primary pressure is acceptable. (author)

  5. American acceptance of nuclear power

    The characteristic adventurous spirit that built American technology will eventually lead to American acceptance of nuclear power unless an overpowering loss of nerve causes us to reject both nuclear technology and world leadership. The acceptance of new technology by society has always been accompanied by activist opposition to industralization. To resolve the debate between environmental and exploitive extremists, we must accept with humility the basic premise that human accomplishment is a finite part of nature

  6. American acceptance of nuclear power

    Barrett, W.

    The characteristic adventurous spirit that built American technology will eventually lead to American acceptance of nuclear power unless an overpowering loss of nerve causes us to reject both nuclear technology and world leadership. The acceptance of new technology by society has always been accompanied by activist opposition to industralization. To resolve the debate between environmental and exploitive extremists, we must accept with humility the basic premise that human accomplishment is a finite part of nature. (DCK)

  7. Decision modeling and acceptance criteria

    Ditlevsen, Ove Dalager

    2003-01-01

    formulation of decision criteria and public acceptance criteria connected to risk analysis of technical operations that may endanger human life and property. Public restrictions on the decisions concerning the design, construction and managing of the technical operation have in the past been imposed on the......, Ronold K. Societal indicators and risk acceptance. In: 17th International Conference on Offshote Mechanics and Arctic Engineering, number OMAE98-1488. ASME; 1998; Rackwitz R. Optimization and risk acceptability based on the Life Quality Index. Structural Safety 2002;24;297-331.). Keywords: Acceptance...

  8. Radioactive waste package acceptance criteria

    Preliminary acceptance criteria have been developed for packages containing nuclear waste which must be stored or disposed of by the US Department of Energy. Acceptance criteria are necessary to ensure that the waste packages are compatible with all elements of the Waste Management System. The acceptance criteria are subject to revision since many of the constraints that will be imposed on the waste packages by the Waste Management System have either not been defined or are being revised. Delineation of the acceptance criteria will provide bases for handling, transporting and disposing of the commercial waste

  9. Italian Consumer Acceptance of Nutritionally Enhanced GM Food

    Canavari, Maurizio; Tisselli, Farid; Nayga, Rodolfo M.; Scarpa, Riccardo

    2009-01-01

    The aim of this article is to evaluate Italian consumers’ acceptance and willingness to purchase GM foods based on the type of benefit (input vs output trait) and product (plant based vs animal based). Two surveys were administered in two consecutive years (2004 and 2005) and the data used to test for possible changes in consumer acceptance. The results of a multinomial logit analysis suggest that on average consumer acceptance for plant-based GM food was higher in 2005. This study confirmed ...

  10. Empirical Study and Model of User Acceptance for Personalized Recommendation

    Zheng Hua

    2013-01-01

    Personalized recommendation technology plays an important role in the current e-commerce system, but the user willingness to accept the personalized recommendation and its influencing factors need to be study. In this study, the Theory of Reasoned Action (TRA) and Technology Acceptance Model (TAM) are used to construct a user acceptance model of personalized recommendation which tested by the empirical method. The results show that perceived usefulness, perceived ease of use, subjective rules...

  11. Worldwide nuclear revival and acceptance

    The current status and trends of the nuclear revival in Europe and abroad are outlined. The development of public opinion in the last decade is playing an important part. This has turned from clear rejection to careful acceptance. Transparency and open communication will be important aspects in the further development of nuclear acceptance. (orig.)

  12. The Usage of Mandarin Acceptable Noise Level Test in Outcome Measurements of Hearing Aids%可接受噪声级测试在助听器效果评估中的初步应用

    陈建勇; 张华; 陈雪清; 吴燕君; 孔颖; 郭连生; 李靖; 李玉玲

    2011-01-01

    目的 探讨可接受噪声级(acceptable noise level,ANL)测试在普通话听障人群助听器效果评估中的应用.方法 选取佩带助听器3个月~3年的中度到中重度听障者37例,根据助听器使用情况将其分为全天使用助听器组、部分时间使用组和拒绝使用组;利用前期经过等价性评估的普通话可接受噪声级测试材料,对三组人群依次进行裸耳和助听下的ANL测试,日常生活助听器满意度问卷(the satisfaction with amplification in daily life,SADL)评估,分析三组ANL值和SADL得分的差异.结果 ①37例听障者个体自身裸耳和助听下最舒适响度级(most comfortable level,MCL)、背景噪声级(background noise level,BNL)值差异有统计学意义(P0.05);②全天使用助听器组裸耳下ANL值明显低于部分时间和拒绝使用助听器组(P0.05);④Pearson相关分析显示:裸耳ANL值与听障者性别、年龄均无相关性(P>0.05),与气导平均听阈存在较弱相关性(r=0.460,P=0.004).结论 可接受噪声级测试可反映个体耐受噪声能力的大小,可初步利用其来预估助听器选配效果.%Objective The purpose of this study was to compare the difference of ANL value among the full -time hearing aid users, part-time users, and nonusers,and then to determine the relationship between the hearing aid outcomes of the three groups and ANL values. Methods 37 hearing aid users for 3 months to 3 years were selected for this research. Listeners were assigned to one of the three groups based on patterns of hearing aid use:full-time use (whenever hearing aids are needed), part-time use (occasional use), and non use. ANL test was measured for the three groups using the mandarin acceptable noise level test material. The mandarin ANL test was measured in aided and unaided conditions for each group; and the outiones were evaluated by SADL. The results were analyzed statistically with SPSS13.0 to determine the differences of the ANL value for the

  13. Automated Transportation Management System (ATMS) V2.0 logistics module PBI acceptance criteria

    This document defines the acceptance criteria for the Automated Transportation Management System V2.0 Logistics Module Performance Based Incentive (PBI). This acceptance criteria will be the primary basis for the generation of acceptance test procedures. The purpose of this document is to define the minimum criteria that must be fulfilled to guarantee acceptance of the Logistics Module

  14. Values, Perceived Risks and Benefits, and Acceptability of Nuclear Energy

    de Groot, Judith I. M.; Steg, Linda; Poortinga, Wouter

    2013-01-01

    We examined how personal values and perceptions of risks and benefits are associated with the acceptability of nuclear energy (NE). A theoretical model is tested in which beliefs about the risks and benefits of NE mediate the relationship between values and acceptability. The results showed that ego

  15. Acceptance of a Theory: Justification or Rhetoric?

    Chow, Siu L.

    1992-01-01

    The rhetoric-analytic critique of experimental psychology owes its apparent attractiveness to (a) some erroneous ideas about cognitive psychology and the rationale of experimentation, (b) the failure to distinguish between prior data and evidential data vis-à-vis the to-be-corroborated explanatory theory, and (c) evidential data owes their identity to a theory that is independent of the theory being tested. Theories in cognitive psychology are accepted because they can withstand concerted eff...

  16. Consumer Acceptance Of Functional Foods In Montenegro

    Zaklina Stojanovic; Jelena Filipovic; Boban Mugosa

    2013-01-01

    This study aimed to investigate determinants of acceptance of functional food in Montenegro and to analyze to what extent these factors affected individuals' consumption of food with health claims. The questionnaire was administered to 479 respondents in Montenegro. The stratified three-stage random sampling method was adopted. Several statistical techniques were employed for investigating data: regression, cluster analysis, independent-samples t test and chi-square. The results indicate that...

  17. Testing the Product Test

    Brea, H.; Grifell-Tatjé, Emili; Lovell, C.A. Knox

    2010-01-01

    The product test asks the product of a quantity index number and a price index number to equal the corresponding value change. The literature treats the product test as being so important that it is used to identify acceptable index number pairs, and to construct implicit index numbers when an otherwise desirable pair fails the test. We treat the product test as a hypothesis to be tested, and we provide an empirical application.

  18. Acceptance- versus Change-Based Pain Management: The Role of Psychological Acceptance

    Blacker, Kara J.; Herbert, James D.; Forman, Evan M.; Kounios, John

    2012-01-01

    This study compared two theoretically opposed strategies for acute pain management: an acceptance-based and a change-based approach. These two strategies were compared in a within-subjects design using the cold pressor test as an acute pain induction method. Participants completed a baseline pain tolerance assessment followed by one of the two…

  19. Examining Engineering & Technology Students' Acceptance of Network Virtualization Technology Using the Technology Acceptance Model

    Yousif, Wael K.

    2010-01-01

    This causal and correlational study was designed to extend the Technology Acceptance Model (TAM) and to test its applicability to Valencia Community College (VCC) Engineering and Technology students as the target user group when investigating the factors influencing their decision to adopt and to utilize VMware as the target technology. In…

  20. Application of QC_DR Software for Acceptance Testing and Routine Quality Control of Direct Digital Radiography Systems: Initial Experiences using the Italian Association of Physicist in Medicine Quality Control Protocol

    Nitrosi, Andrea; Bertolini, Marco; Borasi, Giovanni; Botti, Andrea; Barani, Adriana; Rivetti, Stefano; Pierotti, Luisa

    2008-01-01

    Ideally, medical x-ray imaging systems should be designed to deliver maximum image quality at an acceptable radiation risk to the patient. Quality assurance procedures are employed to ensure that these standards are maintained. A quality control protocol for direct digital radiography (DDR) systems is described and discussed. Software to automatically process and analyze the required images was developed. In this paper, the initial results obtained on equipment of different DDR manufacturers ...

  1. Public acceptance of small reactors

    The success of any nuclear program requires acceptance by the local public and all levels of government involved in the decision to initiate a reactor program. Public acceptance of a nuclear energy source is a major challenge in successful initiation of a small reactor program. In AECL's experience, public acceptance will not be obtained until the public is convinced that the specific nuclear program is needed, safe and economic and environmental benefit to the community. The title of public acceptance is misleading. The objective of the program is a fully informed public. The program proponent cannot force public acceptance, which is beyond his control. He can, however, ensure that the public is informed. Once information has begun to flow to the public by various means as will be explained later, the proponent is responsible to ensure that the information that is provided by him and by others is accurate. Most importantly, and perhaps most difficult to accomplish, the proponent must develop a consultative process that allows the proponent and the public to agree on actions that are acceptable to the proponent and the community

  2. Assessing acceptance of assistive social agent technology by older adults: the Almere model

    M. Heerink; B. Kröse; V. Evers; B. Wielinga

    2010-01-01

    This paper proposes a model of technology acceptance that is specifically developed to test the acceptance of assistive social agents by elderly users. The research in this paper develops and tests an adaptation and theoretical extension of the Unified Theory of Acceptance and Use of Technology (UTA

  3. Produção de brotos de soja utilizando a cultivar BRS 216: caracterização físico-química e teste de aceitabilidade Production of soybean sprouts from the cultivar BRS 216: physical and chemical characterization and acceptability test

    Marcelo Alvares de Oliveira

    2013-03-01

    Full Text Available O presente trabalho teve por objetivo avaliar os parâmetros físico-químicos e os processos para a produção de brotos de soja a partir de sementes da cultivar BRS 216, bem como sua composição química e aceitabilidade. Foram avaliados o comprimento e o peso dos brotos viáveis, a composição centesimal e os teores de isoflavonas e de inibidor de tripsina. O desenho experimental foi ao acaso com três repetições e os tratamentos foram avaliados num esquema fatorial 3 × 3: três frequências de irrigação (a cada quatro, oito e 12 horas e três períodos de crescimento (cinco, seis e sete dias. O teste de aceitabilidade dos brotos de soja foi realizado utilizando-se a escala hedônica estruturada de nove pontos, avaliando-se cor, aparência, odor, textura, sabor e avaliação global, além da intenção de compra. A frequência de irrigação com intervalos de quatro horas e o período de sete dias de crescimento foram ideais para produção dos brotos de soja, favorecendo maior produtividade, teores mais elevados de proteínas e menores teores de inibidor de tripsina. O índice de aceitabilidade dos brotos de soja foi superior a 70 em todas as características avaliadas, com exceção do odor.The aim of the present study was to evaluate the physical and chemical parameters and process for the production of soybean sprouts from the BRS 216 cultivar, as well as determining their chemical composition and acceptability. The length and weight of viable sprouts, proximate composition, and the isoflavone and trypsin inhibitor contents were evaluated. The experimental design was completely randomized with three replications, and the treatments were evaluated using a 3 × 3 factorial design: three irrigation frequencies (four, eight and 12 hours and three growth periods (five, six and seven days. The soybean sprout acceptability was determined using a nine point structured hedonic scale, evaluating colour, appearance, aroma, texture, flavour

  4. Test

    Bendixen, Carsten

    2014-01-01

    Bidrag med en kortfattet, introducerende, perspektiverende og begrebsafklarende fremstilling af begrebet test i det pædagogiske univers.......Bidrag med en kortfattet, introducerende, perspektiverende og begrebsafklarende fremstilling af begrebet test i det pædagogiske univers....

  5. Validation and acceptance of synthetic infrared imagery

    Smith, Moira I.; Bernhardt, Mark; Angell, Christopher R.; Hickman, Duncan; Whitehead, Philip; Patel, Dilip

    2004-08-01

    This paper describes the use of an image query database (IQ-DB) tool as a means of implementing a validation strategy for synthetic long-wave infrared images of sea clutter. Specifically it was required to determine the validity of the synthetic imagery for use in developing and testing automatic target detection algorithms. The strategy adopted for exploiting synthetic imagery is outlined and the key issues of validation and acceptance are discussed in detail. A wide range of image metrics has been developed to achieve pre-defined validation criteria. A number of these metrics, which include post processing algorithms, are presented. Furthermore, the IQ-DB provides a robust mechanism for configuration management and control of the large volume of data used. The implementation of the IQ-DB is reviewed in terms of its cardinal point specification and its central role in synthetic imagery validation and EOSS progressive acceptance.

  6. Wind power: basic challenge concerning social acceptance

    M. Wolsink

    2012-01-01

    This reference article gives an overview of social acceptance (acceptance by all relevant actors in society) of all relevant aspects of implementation and diffusion of wind power. In social acceptance three dimensions of acceptance are distinguished (socio-political -; community -; market acceptance

  7. The real problem: public acceptability

    The paper concerns the problem of public acceptibility of radioactive waste disposal in the United Kingdom. U.K. Nirex has responsibility for developing a deep repository for low-and intermediate-level radioactive wastes in the U.K., and it is also developing a public information programme aimed at obtaining public acceptibility for such a repository. The main objective of the programme is to raise the level of public awareness of radioactive waste disposal to the point where scientifically supported assurances on safety and environmental impact would be accepted by concerned people. Previous experience of Nirex in dealing with the public on the waste disposal issue is described - this includes the public opposition to the proposed use of Billingham and Elstow as sites for a repository. The main lesson learnt from the latter opposition by Nirex is that public relations must be part of Nirex's main business. (U.K.)

  8. Stochastic phonological grammars and acceptability

    Coleman, J; Coleman, John; Pierrehumbert, Janet

    1997-01-01

    In foundational works of generative phonology it is claimed that subjects can reliably discriminate between possible but non-occurring words and words that could not be English. In this paper we examine the use of a probabilistic phonological parser for words to model experimentally-obtained judgements of the acceptability of a set of nonsense words. We compared various methods of scoring the goodness of the parse as a predictor of acceptability. We found that the probability of the worst part is not the best score of acceptability, indicating that classical generative phonology and Optimality Theory miss an important fact, as these approaches do not recognise a mechanism by which the frequency of well-formed parts may ameliorate the unacceptability of low-frequency parts. We argue that probabilistic generative grammars are demonstrably a more psychologically realistic model of phonological competence than standard generative phonology or Optimality Theory.

  9. Nuclear Energy and Public Acceptance

    The continued use of nuclear power in the European Union and elsewhere requires an adequate level of public and political acceptance. A lack of acceptance is often mistakenly cited as a reason for the slowdown in nuclear power plant construction in Western Europe and as a justification for abandoning nuclear power. In fact, the reasons for the slowdown have more to do with the following two factors: Plentiful supplies of low-priced natural gas, making gas-fired power plants a more attractive investment choice; more than adequate supplies of electricity which have curbed the need for the construction of new plant of any kind. In general, moves towards a withdrawal from nuclear in certain Community countries have been due to party political pressures and have not been a response to public opposition to nuclear. In addition, opinion polls do not show widespread public opposition to the use of nuclear power. Figures consistently indicate that the use of nuclear power does not come high on the list of most people's main worries. Their main concerns focus on other issues such as crime and financial problems. In the main, electricity is taken for granted in the industrialised world. Electric power only becomes an issue when there is a threat of shortages. So if public acceptance is not the main obstacle, what is? Political acceptance is an integral part of the process in which nuclear becomes acceptable or not. The relationship between public and political acceptance and the role of the industry in this context, on how to foster a better trialogue, will be examined. (author)

  10. Safety culture and public acceptance

    After the Chernobyl NPP accident a public acceptance has become a key factor in nuclear power development all over the world. Therefore, nuclear safety culture should be based not only on technical principles, responsibilities, supervision, regulatory provisions, emergency preparedness, but the public awareness of minimum risk during the operation and decommissioning of NPPs, radioactive waste management, etc. (author)

  11. AAL- technology acceptance through experience

    Huldtgren, A.; Ascencio San Pedro, G.; Pohlmeyer, A.E.; Romero Herrera, N.A.

    2014-01-01

    Despite substantial research and development of Ambient Assisted Living (AAL) technologies, their acceptance remains low. This is partially caused by a lack of accounting for users' needs and values, and the social contexts these systems are to be embedded in. Participatory design has some potential

  12. Euthanasia Acceptance: An Attitudinal Inquiry.

    Klopfer, Fredrick J.; Price, William F.

    The study presented was conducted to examine potential relationships between attitudes regarding the dying process, including acceptance of euthanasia, and other attitudinal or demographic attributes. The data of the survey was comprised of responses given by 331 respondents to a door-to-door interview. Results are discussed in terms of preferred…

  13. Worldwide nuclear revival and acceptance

    The paper outlines the current status and trends of the nuclear revival in Europe and abroad, the evolution of the public opinion in the last decade, and the interaction between the former and the latter. It emphasises the absolute priority of a professional communication and exchange to gain public acceptance. (orig.)

  14. Teste de aceitação e composição centesimal de carne de jacaré-do-papo-amarelo (Caiman latirostris em conserva Acceptance test and percent composition of broad-snouted caiman (Caiman latirostris canned meat

    Isabela Ciarlini de Azevedo

    2009-04-01

    jacaré-do-papo-amarelo em conserva é viável, permitindo o melhor aproveitamento da carne após o abate, com aumento do seu valor agregado e uma boa aceitação sensorial do produto.This research focused on the evaluation of three broad-snouted caiman (Caiman latirostris canned meat formulas: one in edible oil, another in salt with onions, and the third one in seasoned salt. Some cuts (six pairs of members, one tail, two ribs and two loins were separated after slaughter to produce the canned meat. Gas chromatographic analysis of the fatty acids in the non-processed meat was conducted before industrial processing. After the canning process, a commercial sterility test for low acidity food was conducted for the canned meat samples. Subsequently, the three formulations were tested for sensory acceptance by a 9-point hedonic scale with respect to their appearance and global impression. The sodium chloride content, pH and percent composition (moisture, fixed mineral residue, proteins and lipids contents of the canned meat samples were determined. The saturated, monounsaturated and polyunsaturated fatty acids values were, respectively, 28.5; 42.5 and 29.0% of the total fatty acids in the non-processed meat. The canned meat samples were released after verifying that there were no leaking or blown cans in the sterility test. The three samples were significantly different in respect to appearance. The results showed the following order, from the least to the most acceptable sample: salt with onions, seasoned salt and edible oil. As for the global impression, the formulation in edible oil was also the most acceptable. The sodium chloride content was in the range of 0.5 to 1.2%, where the highest value was found for the samples in salt. The canned meat samples had an average pH of 5.0, 76.0% moisture content and 1.3% of fixed mineral residue, a protein concentration of 12.4% and a total lipid content of 5.5%. The sample in edible oil showed a higher concentration of lipids (12

  15. A structural model of technology acceptance

    Etienne Erasmus

    2015-02-01

    Full Text Available Orientation: Enterprise resource systems have not always led to significant organisational enhancement and many projects in which these systems have been implemented turn out to be over budget, not on time and unsuccessful.Research purpose: The aim of this study was to test the technology acceptance model within a South African SAP® Enterprise Resource Planning user environment.Motivation for the study: No study could be traced in which the technology acceptance model has been evaluated in the South African context.Research approach, design and method: A cross-sectional survey design was used. The 23-item Technology Acceptance Model Questionnaire was deployed amongst SAP® Enterprise Resource Planning users (N = 241. Main findings: The results confirmed significant paths from perceived usefulness of the information system to attitudes towards and behavioural intentions to use it. Furthermore, behavioural intention to use the system predicted actual use thereof. Perceived ease of use indirectly affected attitudes towards and behavioural intentions to use via perceived usefulness of the information system.Practical/managerial implications: Practitioners should build user confidence by ensuring the ease of use of a new system, providing relevant education, training and guidance and reiterating its usefulness and future added value to the user’s job and career.Contribution/value-add: This study contributes to scientific knowledge regarding the influence of individuals’ perceptions of information system usage on their attitudes, behavioural intentions and actual use of such a system.

  16. 105 K East isolation barrier acceptance analysis report

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KE/100K. The tests were performed in accordance with the test plan (McCracken 1995c) and acceptance test procedure (McCracken 1995a). The test report (McCracken 1995b) contains the test data. This document compares the test data (McCracken 1995b) against the criteria (McCracken 1995a, c). A discussion of the leak rate analytical characterization (Irwin 1995) describes how the flow characteristics and the flow rate will be determined using the test data from the test report (McCracken 1995b). The barriers must adequately control the leakage from the main basin to the discharge chute to less than the 1,500 gph (5,680 lph) Safety Analysis Report (SAR 1994) limit

  17. Study on public acceptance of irradiated potatoes

    4,500 kg potatoes of different sorts were irradiated by a 137Cs source with a dose of 10 krad. The potatoes were then stored for several months at a room temperature of 6 to 100C and a humidity of 80 to 85%. 0% of the irradiated potatoes sprouted, as compared to 100% of the non-irradiated potatoes. The percentage of rotting varied in the irradiated potatoes, depending on the variety. Cooking tests showed no difference between irradiated and non-irradiated potatoes. The irradiated potatoes were consumed and accepted by about 4,000 persons in the cafeteria of the institute. (AJ)

  18. Empirical Study and Model of User Acceptance for Personalized Recommendation

    Zheng Hua

    2013-02-01

    Full Text Available Personalized recommendation technology plays an important role in the current e-commerce system, but the user willingness to accept the personalized recommendation and its influencing factors need to be study. In this study, the Theory of Reasoned Action (TRA and Technology Acceptance Model (TAM are used to construct a user acceptance model of personalized recommendation which tested by the empirical method. The results show that perceived usefulness, perceived ease of use, subjective rules and trust tend had an impact on personalized recommendation.

  19. The Chinese in America : A Recently Accepted Old Immigrant Group

    2002-01-01

    This thesis, "The Chinese in America: A Recently Accepted Old Immigrant Group," aims at testing the hypothesis that the transition of Chinese immigrants into an accepted ethnic group in mainstream America and their influence on the evolution of the American identity were mainly regulated by the United States economy. This hypothesis is rooted in the belief that their primary arena of ethnicization was the labor market, first the California labor market, then the national one. The Chinese were...

  20. The Influence of Trust on Internet Banking Acceptance

    Khalil Md Nor; J Michael Pearson

    2007-01-01

    The theory of diffusion of innovation (IDT) has been widely used to examine factors that influence an individual to adopt an innovation or a new technology. In online environment, trust has been suggested to play an important role in influencing one’s acceptance of an innovation. The purpose of this study is to test empirically the influence of trust together with some of the attributes of IDT on Internet banking acceptance. We surveyed 1164 business students and MBAs in f...