Energy Technology Data Exchange (ETDEWEB)

The high temperature abrasive wear resistant of the composites with different Al{sub 2}O{sub 3} volume fractions, particle coating and size were investigated and the failure action of composites under different conditions at high temperature was analyzed. The results showed that the high temperature abrasive wear resistant of composite with Ni coating and wide size and 39% volume fraction of particle is the best among all composites examined. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The properties of cast basalt and alumina are examined. The ways in which these materials have been used in applications in coal preparation plants, for example in bunker and pipe linings where abrasion and corrosion resistant materials are required, are discussed.

Energy Technology Data Exchange (ETDEWEB)

Prior to 1986, the abrasive coking coal processed in the coal preparation plant at the Fording River operation at Elkford, British Columbia, was destroying the mild steel straight pipe and elbows at such a rate that they were having to be replaced annually and every 6-8 months respectively. To solve the problem, Fording River began to replace existing pipe and elbows with fused-cast, basalt-lined abrasion-resistant pipe, elbows and fittings manufactured by Abresist Corp. of Urbana, Indiana. The Abresist straight pipe has lasted 7 seven years and the Abresist elbows 5 years and both are still in use. 2 photos.

Science.gov (United States)

This study investigated the effect of board type (unmodified vs. MAPE modified) on the surface quality and thickness swelling-water absorption properties of recycled high density polyethylene (HDPE) based wood plastic composites. Additionally, two commercially available coatings (cellulosic coating and polyurethane lacquer coating) were also applied to composite surfaces and their adhesion strength, abrasion and scratch resistance, and gloss values were determined. This study showed that modification of the composites with MAPE coupling agent increased the surface smoothness and reduced the water absorption and thickness swelling of the panels. Abrasion resistance of the composites was also improved through MAPE modification. Regardless of board type, higher scratch resistance and gloss values were observed for polyurethane lacquer coated samples compared to those of cellulosic ...

Science.gov (United States)

A rapidly hydrated sorbent for moderate-temperature dry flue gas desulfurization was prepared by rapidly hydrating adhesive carrier particles and lime. The circulation ash from a circulating fluidized bed boiler and chain boiler ash, both of which have rough surfaces with large specific surface areas and specific pore volumes, can improve the adhesion, abrasion resistance, and desulfurization characteristics of rapidly hydrated sorbent when used as the adhesive carrier particles. The adhesion ability of sorbent made from circulation ash is 67.4% higher than that of the existing rapidly hydrated sorbent made from fly ash, the abrasion ratio is 76.2% lower, and desulfurization ability is 14.1% higher. For sorbent made from chain boiler ash, the adhesion ability is increased by 74.7%, the desulfurization ability is increased by 30.3%, and abrasion ratio is decreased by 52.4%. The ...

Energy Technology Data Exchange (ETDEWEB)

A filter for extracting solids and liquids from gaseous combustion exhausts comprises a textile filter element formed of polyacrylonitrile fibers oxidized by careful heat treatment and comprising approximately 61% carbon after treatment. The filter may be woven, knitted or formed as a batting of randomly-oriented fibers. Abrasion resistant coatings and lubricants for the fibers are disclosed. The filter material is especially useful as a filter bag.

Science.gov (United States)

... Accession Number : ADD330829. Title : NOZZLE WEAR DETECTION IN ABRASIVE WATERJET CUTTING SYSTEMS,. Corporate Author : ...

Energy Technology Data Exchange (ETDEWEB)

The present paper deals with the fouling process of calcium sulfate dehydrate on heat-transfer surfaces. The crystallization of calcium sulfate showed typical asymptotic fouling curves, the asymptotic value of which was greatly influenced by the surface temperature and fluid velocity. The fouling mechanism was discussed with a generalized fouling model and proved to be surface process controlled, where the activation energy was 6.2 {times} 10{sup 4} J/mol. The availability of mechanical cleaning against the formed scale was quantitatively evaluated by applying the particle abrasion method. The removal test verified that the removing rate per unit particle concentration decreased in an inverse proportion to the overall particle load, to the power of 0.8, and that it was affected by the fluid velocity. The observed final residual fouling resistance decreased asymptotically with an increase in particle concentration. The suitable concentration of ...

International Nuclear Information System (INIS)

The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester resins improved the impact strength of wood composite materials. (author).

Energy Technology Data Exchange (ETDEWEB)

Effect of final temperature and duration of coking on the properties of formed coke from weakly-caking Donetsk and Kuznetsk coals was studied. An increase of the final temperature to 850 C produced significant changes in the mechanical and chemical properties of the coke. Increasing the temperature beyond this point did not affect the mechanical strength significantly, but did increase hardness, real density and electroconductivity of the coke and decrease reactivity. Increasing the period of coking at final temperatures in the 650 and 750 C range, produced insignificant hardening of the formed coke. An objective evaluation of the effect of final temperature can be performed by a series of tests which characterize the resistivity of the formed coke to impact and abrasion and the fine structure of the matter in coke. 9 references.

Energy Technology Data Exchange (ETDEWEB)

Titanium alloys are characterized by poor tribological properties, and the traditional use of titanium alloys has been restricted to nontribological applications. The deposition of a well adherent diamond coating is a promising way to solve this problem. In this study, the tribological properties of diamond-coated titanium were studied using a pin-on-disk tribometer, and the results were compared with those of pure titanium and plasma nitrided titanium. The tribological behavior of pure titanium was characterized by high coefficient of friction and rapid wear of materials. Plasma nitriding improved the wear resistance only under low normal load; however, this hardened layer was not efficient in improving the wear resistance and the friction properties under high normal load. Diamond coating on pure titanium improved the wear resistance of titanium significantly. Surface profilometry measurement indicated that little or no ...

Energy Technology Data Exchange (ETDEWEB)

There is presently considerable interest in wear resistant coatings produced using closed field unbalanced magnetron sputtering technology. For example, layered films of diamond-like carbon (DLC) with tungsten or titanium additions have been widely reported. The benefit is that the mechanical properties are enhanced (e.g. giving greater toughness); also it is possible to control the stress state and enhance adhesion. Here we report the further development of this concept by the addition of TiN, TiCN and TiC layers in DLC-based composites, utilizing an additional source of electrons in the vicinity of substrate to enhance ionisation of the plasma and increase coating density. Composite coatings of ceramics TiN, TiC{sub x}N{sub y}, TiC, CrN, TiCrN, TiCrCN, TiCrC, metal doped Ti{sub x%}-DLC and their combinations were deposited on 316 stainless steel substrates. The mass flow of reactive gases into the chamber was controlled using plasma optical emission monitoring to ...

Energy Technology Data Exchange (ETDEWEB)

The dispersion of more than 20 vol pct submicrometer ceramic particles within a metallic matrix and the deposition of such a cermet to form a thick and tough coating presents problems. Most of the coating techniques have failed in attempting to homogeneously disperse very fine and hard particles in large amounts while avoiding their decomposition or reaction with the metal matrix during the deposition process. A simple and efficient method has been developed for producing ceramic-containing composite coatings. It consists in synthesizing cermet-based materials and in depositing them by a rapid solidification process, such as thermal spraying. Boride- and carbide-based materials have been successfully obtained by plasma spraying reactive powders comprising the basic reagents. These materials, with a microstructure of submicrometer ceramic particles dispersed in a metallic matrix, exhibit good wear-resistant properties (abrasion and sliding ...

British Library Electronic Table of Contents (United Kingdom)

BACKGROUND: Glyphosate resistance has been confirmed in 58 populations of Lolium rigidum (Gaud.), a major weed of crops in southern Australia. Extensive use of glyphosate in conjunction with minimal soil disturbance has been identified as high risk for resistance to that herbicide. Land managers need a simple method for rapid assessment of the risk of resistance occurring as a result of past and proposed future management practices. Modelled on risk assessment nomographs, a simple calculator for indicating the risk of evolved glyphosate resistance in L. rigidum is described.RESULTS: The calculator uses the generations since first use and the frequency of use of glyphosate in combination with historical cultivation levels as critical factors for determining the risk of glyphosate resistance...

International Nuclear Information System (INIS)

Russian 2010 p. 382 Ukraine Yuferov, VB Ozerov, AN Ponomarev,

Environmental Research Database

DescriptionThis project investigates in silico the interactive consequences of breeding for parasite resistance and nutritional environment on livestock productivity. The thesis of the work is that conflicting evidence regarding the consequences of breeding for parasite resistance arises from the failure to consider the interactions between host genetics and nutritional environment. Starting with a framework that accounts for the consequences of host nutrition on the development of parasitism, we will (1 [continued...

British Library Electronic Table of Contents (United Kingdom)

Zirconium and particularly Zr-2.5wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate. In this study, we demonstrate a two step pro...

British Library Electronic Table of Contents (United Kingdom)

A type of Si3N4-based nanocomposites ceramic cutting tool material was prepared by the addition of nano-scale Si3N4W whisker and nano-scale TiN particle. Cutting performance of the Si3N4/Si3N4W/TiN nanocomposite ceramic tool in machining of cast iron was investigated in comparison with a commercial sialon ceramic tool, and the tool wear mechanism was studied. The two types of cutting tools have similar cutting performance at relatively low cutting parameters, while Si3N4/Si3N4W/TiN nanocomposite tool exhibits a better wear resistance than sialon tool at the relatively high cutting parameters. The wear of sialon ceramic cutting tool is dominated by the plastic deformation, abrasive action, microcracking, pullout of grains and chemical action at the higher cutting parameters. The higher mech...

Energy Technology Data Exchange (ETDEWEB)

In response to a heat shock, the yeast Saccharomyces cerevisiae undergoes a large increase in its resistance to heat and, by the induction of its recombinational DNA repair capacity, a corresponding increase in resistance to radiation. Yeast which lack mitochondrial DNA, mitochondria-controlled protein synthetic apparatus, aerobic respiration, and electron transport (rho/sup 0/ strain) were used to assess the role of O/sub 2/, mitochondria, and oxidative processes controlled by mitochondria in the induction of these resistances. We have found that rho/sup 0/ yeast grown and heat shocked in either the presence or absence of O/sub 2/ are capable of developing both radiation and heat resistance. We conclude that neither the stress signal nor its cellular consequences of induced heat and radiation resistance are directly dependent on O/sub 2/, mitochondrial DNA, or ...

Energy Technology Data Exchange (ETDEWEB)

Particulate Reinforced Titanium matrix composites (PRTi) exhibit some improved specific mechanical properties in comparison with those of unreinforced titanium alloys as a result of the combination of the high strength and stiffness of ceramic particles with the toughness and damage tolerance provided by the metal matrix. The poor tribological properties of the titanium exclude titanium alloys from applications where wear resistance is required (brakes, rotating parts, sliding parts). The addition of ceramic particles improves the tribological properties of metals sensitive to adhesive and /or abrasive wear significantly. In this work, the wear resistance and the friction coefficient of Ti6Al-6V-2Sn reinforced with TiC particles and Ti6Al-4V reinforced with SiC particles (prototype material) are compared with the unreinforced alloys. Pin on disc and pin on ring tests were carried out against standard steel (100Cr6) as a ...

Energy Technology Data Exchange (ETDEWEB)

The exposure of heat-resistant alloys to high temperature can significantly change their mechanical properties. This paper presents and analyzes data on the effect of thermal exposure on the tensile and impact behavior of three cast materials -- the HK-40, HP-50, and 21Cr-32Ni-Fe alloys -- and of wrought material -- Alloy 800. The changes in tensile and impact properties caused by high-temperature exposure are reviewed. Reasons for these property changes and needs for considering them in the design, operation, and life assessment of high-temperature equipment are discussed.

International Nuclear Information System (INIS)

Intergranular corrosion (IGC) resistance of types 304LN and 316LN stainless steels (SS) thermally aged at 823, 873, and 923 K for various durations was assessed by ASTM A262 practice A test (electrolytic etch test) and electrochemical potentiodynamic reactivation (EPR) test. The results indicated that the type 316LN SS has significantly improved IGC resistance compared to 304LN SS. Based on the results of these tests, time-temperature-sensitization (TTS) diagrams were developed for both alloys. The secondary precipitates formed during thermal aging treatments were electrochemically extracted and analyzed by X-ray diffraction (XRD) to determine the types of precipitates formed during the aging treatments. The results indicated that the precipitates were mostly of M_2_3C_6 carbides.

Energy Technology Data Exchange (ETDEWEB)

The first part of the conference dealt with environmental effects of using coal. Papers dealt with the use of fly ash in agriculture and its effect on plant growth; the effect of airborne emissions on fish and wildlife resources, on watersheds, and on airsheds; the effects of surface mining on the ecology; blast effects; and health hazards associated with coal. The session on policy studies addressed the issue of cost of synthetic fuels and discussed the state and federal pollution regulations on burning coal and waste disposal. The session on combustion presented papers on atmospheric and pressurized fluidized-bed combustion for industrial and utility boilers. It also included papers on MHD power plants, coal-oil and coal-water mixtures, emission characterization and control, and catalytic combustors. The design of gasification plants, reaction kinetics, specific heats of coals and chars, simultaneous production of liquid and gaseous fuels, and economics of fuel substitution with coal ...

British Library Electronic Table of Contents (United Kingdom)

Major similarities between robustness assessment and seismic design exist, and significant information can be brought from seismic design to robustness design. As will be discussed, although some methods and limitations considered in seismic design can improve robustness, the capacity of the structure to sustain limited damage without disproportionate effects is significantly more complex. In fact, seismic design can either improve or reduce the resistance of structures to unforeseeable events, depending on the structural type, triggering event, structural material, among others. Based on a case study, the influence of redundancy and ductility on the seismic behavior and robustness of a long-span timber structure is assessed.

UK PubMed Central (United Kingdom)

Background and ObjectivesClopidogrel resistance or low-responsiveness may be associated with recurrent atherothrombotic events after drug-eluting stent (DES) implantation. We prospectively...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A method of abrasion testing according to ASTM C 704-76 a is presented for steel fibre concrete mortar, fusion-cast basalt and a surface coating material and results of practical interest are mentioned. Due to the high technical demands on these materials and their specific fields of application, the very first test already supplied interesting findings. From the user's point of view, the method is an interesting alternative to the common test methods, e.g. according to DIN 52 108 (wheel test according to Boehme). In English-speaking countries, testing according to ASTM is often mandatory in the refractory industry in order to assure constant quality of refractory materials after setting. The method is characterized by good comparability and high accuracy of measurement. Only the test piece is exchanged while the test conditions remain constant, so that accurate information on the material studied is obtained.

Energy Technology Data Exchange (ETDEWEB)

For years rock bit performance has been progressively improved by many innovative changes to the design of both the bit cutting structure and the bearing. The changes have offered increased footage per bit and reduced cost per foot of hole through longer bit life and/or faster penetration rate. Efforts to assist the industry in drilling deeper thru hard abrasive rocks such as cherts of West Texas, conglomerated of the Rockies and bromides of Oklahoma led to a major breakthrough in rock bit design - the development of the tungsten carbide cutting structure. When properly applied the bit far exceeded that of the non-sealed ball and roller bearing being used at the time. The bearing failure mode was one of severe race spalling and abrasive wear influenced by the drilling fluid entering the bearing.

International Nuclear Information System (INIS)

No prospective studies have evaluated the effects of correction of iron deficiency anemia on insulin resistance in non-diabetic premenopausal women with iron deficiency anemia. All patients were treated with oral iron preparations. Insulin resistance was calculated with the Homeostasis Model Assessment formula. All patients were dichotomized by the median for age and BMI to assess how the relationship between iron deficiency anemia and insulin resistance was affected by the age and BMI. Although the fasting glucose levels did not change meaningfully, statistically significant decreases were found in fasting insulin levels following anemia treatment both in the younger age (<40 years) (P=0.40) women and in the low BMI (27 kg/m) (P=0.22) subgroups but not in the older age (>= 40 years) and the high BMI (>-27Kg/m) subgroups. Post-treatment fasting insulin levels were ...

Energy Technology Data Exchange (ETDEWEB)

This study presents the results of an 18-year long investigation of pipe deterioration in cyclone slag slurry transport. The goal was to study pipe behaviour in this extremely abrasive service and select an optimum piping material. Comparisons are given for high quality alloy cast steel pipes and pipes lined with cast basalt rings marketed under the name Abresist. Based on the results, thoughts are offered on the broader meanings of certain findings.

Science.gov (United States)

Kong-Ming Wu (Corresponding author) The application of recombinant DNA technology has resulted in many insect-resistant varieties by genetic engineering (GE). Crops expressing Cry toxins derived from Bacillus thuringiensis (Bt) have been planted worldwide, and are an effective tool for pest control. However, one ecological concern regarding the potential effects of insect-resistant GE plants on non-target organisms (NTOs) has been continually debated. In the present study, we briefly summarize the data regarding the development and commercial use of transgenic Bt varieties, elaborate on the procedure and methods for assessing the non-target effects of insect-resistant GE plants, and synthetically analyze the related research results, mostly those published between 2005 and 2010. A mass of laboratory and field studies have shown that the currently available Bt crops have no direct detrimental effects on ...

Science.gov (United States)

Isocapnic hyperventilation with cold air (IHCA) is a reliable technique for assessing indirect bronchial hyperresponsiveness in patients with asthma. Impedance measurement of the respiratory system by the forced pseudorandom noise oscillation technique is a sensitive technique to assess changes in bronchial tone after IHCA. The aim of this study was to evaluate the effect of 6 weeks of treatment with beclomethasone dipropionate, 1,000 microg x day-1, on IHCA in asthmatic patients, measured with both forced oscillation technique and flow-volume recordings. Forty patients with mild asthma were included in this double-blind, placebo-controlled parallel-group study. Stratification on the basis of sex was performed to overcome differences in airway diameter. At entry and every 2 weeks during the treatment period, IHCA was performed and patient diaries were evaluated. Characteristic changes in forced oscillation parameters after IHCA were observed in ...

Energy Technology Data Exchange (ETDEWEB)

Age-related deterioration of the fracture properties of bone, coupled with increased life expectancy, are responsible for increasing incidence of bone fracture in the elderly, and hence, an understanding of how its fracture properties degrade with age is essential. The present study describes ex vivo fracture experiments to quantitatively assess the effect of aging on the fracture toughness properties of human cortical bone in the longitudinal direction. Because cortical bone exhibits rising crack-growth resistance with crack extension, unlike most previous studies the toughness is evaluated in terms of resistance-curve (R-curve) behavior, measured for bone taken from wide range of age groups (34-99 years). Using this approach, both the ex vivo crack-initiation and crack-growth toughness are determined and are found to deteriorate with age; the initiation toughness decreases some 40% over six decades from 40 to 100 years, ...

British Library Electronic Table of Contents (United Kingdom)

In situ composite coating of hydroxyapatite (HA)/TiO2 were produced on titanium (Ti) substrate by micro-arc oxidation coupled with electrophoretic deposition (MAO&EPD) technique with different concentrations of HA particles in the 0.2M NaOH electrolyte solution. The surface morphology and chemical composition of the hybrid coating were effected by HA concentration. The amount of HA particles incorporated into coating layer increased with increasing HA concentration used in the electrolyte solution. The corrosion behavior of the coating layer in simulated body fluids (SBF) was evaluated using a potentiodynamic polarization test. The corrosion resistance of the coated sample was increased compared to the untreated Ti sample. The in vitro bioactivity assessment showed that the MAO&EPD treated...

Energy Technology Data Exchange (ETDEWEB)

Ecosystems worldwide are experiencing unprecedented nitrogen enrichment through fertilization and pollution. While longterm ecological consequences are difficult to predict, it seems that plants and animals adapted to nitrogen-limited environments are at particular risk from these changes. This report summarizes the limited body of literature which addresses this important topic. From a herbivoreAes perspective, fertilization increases the nutritional quality of host plant tissues. In some cases fertilization has lead to decreased production of defensive compounds. How this affects populations of insects is unclear because fertilization affects not only herbivores but their natural enemies. This report outlines how fertilization affects tree processes such as growth, photosynthesis, and production of defensive compounds. The many factors that affect insect repsonse to fertilization and the difficulties in assessing how fertilization affects insect populations are ...

British Library Electronic Table of Contents (United Kingdom)

Australia?s nationally consistent framework for gene technology regulation is underpinned by the Gene Technology Act 2000, administered by an independent decision-maker, the Gene Technology Regulator. The object of the Act is ?to protect the health and safety of people, and to protect the environment, by identifying risks posed by or as a result of gene technology, and by managing those risks through regulating certain dealings with genetically modified organisms?. Marketing and trade impacts are outside the scope of assessments required by the Act. Since 2001, seven licences have been issued for the commercial cultivation of genetically modified (GM) cotton with insect resistance and/or herbicide tolerance. Licences have also been issued for 32 GM cotton field trials with a broader range ...

Energy Technology Data Exchange (ETDEWEB)

Encapsulation of technetium-99m sestamibi ({sup 99m}Tc-MIBI) in polyethyleneglycol-liposomes ({sup 99m}Tc-MIBI-PEG-liposomes) could extend the duration of its circulation in blood and alter its biodistribution, enabling its concentration in tumours to be increased. An original method to encapsulate {sup 99m}Tc-MIBI in PEG-liposomes is described. The {sup 99m}Tc-MIBI-PEG-liposomes were compared with free {sup 99m}Tc-MIBI with respect to (a) tumour availability (b) ability to distinguish between chemotherapy-sensitive and -resistant cells and (c) uptake ratio in tumour imaging. PEG-liposomal systems composed of distearoylphosphatidylcholine/cholesterol/PEG{sub 2000}-distearoyl phosphatidylethanolamine and lissamine-rhodamine B-labelled liposomes were used. The encapsulation of {sup 99m}Tc-MIBI in liposomes was achieved using the K{sup +} diffusion potential method. We compared the uptake of free versus encapsulated {sup 99m}Tc-MIBI by sensitive and ...

Science.gov (United States)

An experimental investigation was conducted to determine the feasibility of machining isogrid structures with abrasive-waterjets (AWJs). The main objective was to mill isogrid patterns in surfaces with accurate depth control using an AWJ. Three different approaches using AWJs were tested: linear cutting of isogrid patterns for diffusion bonding, milling with conventional AWJ nozzles, and milling with a single-angled rotary AWJ nozzle. It was shown that pocket milling with conventional AWJs is the most feasible of those tested. The milling can be done internally on preformed aluminum tubes, and the AWJ can also be used on materials other than aluminum. Accurate depth control can be achieved at high productivity rates. As an example, it is projected that a 48-inch-diameter skirt 12 inches high could be milled with an isogrid pattern in 6.3 hours. Milled isogrid patterns can be controlled to 0.001 inch, and thin walls of less than 0.025 inch are achievable. Milling ...

Science.gov (United States)

The Abrasive Waterjet Cutting process was evaluated to determine if the equivalent could be utilized for cutting uranium metal at the Feed Materials Production Center (FMPC). In the process, a thin stream of ultrahigh pressure water carried grit material through a designated piecepart. In order to be acceptable for use at the FMPC, the equipment must be cost effective, minimize waste, and be adaptableto operating in an enclosure, and improve health and safety conditions. Observation of the cutting process showed that health and safety aspects could be optimized with an enclosed ventilated system. Also the equipment can be easily automated. The cutting action produced sparks similar to the sparks caused by a grinding operation. The sparks are captured in a water container under the workpiece that not only catches the sparks, but also serves to dissipiate the stream of water and residues produced by the cut. Metallographic tests performed on the cut surface of the ...

UK PubMed Central (United Kingdom)

Because resistance to new insecticides may develop rapidly and cross resistance is often encountered, even between insecticides of different classes, there is a continual demand for the development...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Describes performance of excavator teeth manufactured with a new hard alloy. The alloy was developed by the Donetskii Politeknicheskii Institute. Its composition consists of a high-chromium steel with a larger amount of titanium than serial alloy, and a nitrogen additive. Trial tests of new alloy teeth were carried out in the Severnyi and Vershinskii coal surface mines. The teeth were attached to EhRP, EhPG and EhR bucket wheel excavators. Abrasive wear of 129 experimental teeth and 134 serial teeth was compared for different excavation conditions. Test results are tabulated; advantages of the new experimental teeth are listed. 3 refs.

Energy Technology Data Exchange (ETDEWEB)

Assessment on the back end fuel cycle, in PEACER (Proliferation-resistant Environmental-friendly Accident-tolerant Continuable and Economical Reactor) that was designated as a new transmutation concept, was performed. Recovery system of uranium and TRU for PEACER is based on pyroprocessing. In the assessment of Long-Lived Fission Products (LLFP) wastes, initially {sup 90}Sr and {sup 137}Cs are dominant contributor nuclides until 30 years and especially {sup 90}Sr and {sup 137}Cs have the highest activity and decay heat than other LLFP. In this study, recovery of {sup 90}Sr and {sup 137}Cs is recommended for reducing of wastes loading. The acceptable decontamination factor is investigated by the toxicity of PEACER spent fuel. The acceptable decontamination factor is about 1.02E+05 for the actinides from PEACER spent fuel after 10 years cooling, 4.26E+05 after 100 years cooling, 1.97E+04 after 300 years cooling, 9.52E+03 ...

International Nuclear Information System (INIS)

Assessment on the back end fuel cycle, in PEACER (Proliferation-resistant Environmental-friendly Accident-tolerant Continuable and Economical Reactor) that was designated as a new transmutation concept, was performed. Recovery system of uranium and TRU for PEACER is based on pyro-processing. In the assessment of long-lived fission products (LLFP) wastes, initially "9"0Sr and "1"3"7Cs are dominant contributor nuclides until 30 years and especially "9"0Sr and "1"3"7Cs have the highest activity and decay heat than other LLFP. In this study, recovery of "9"0Sr and "1"3"7Cs is recommended for reducing of wastes loading. The acceptable decontamination factor is investigated by the toxicity of PEACER spent fuel. The acceptable decontamination factor is about 1.02 E+05 for the actinides from PEACER spent fuel after 10 years cooling, 4.26 E+05 after 100 years cooling, 1.97 E+04 after 300 years cooling, 9.52 E+03 after 1000 years ...

International Nuclear Information System (INIS)

Ferritic/martensitic steel, modified 9Cr-1Mo steels have been used most extensively in the power generation industry throughout the world due to having superior high temperature properties such as high strength, creep resistance, and good microstructure stability. These steels are also the primary candidate for the RPVs(Reactor Pressure Vessels) of High Temperature Gas-Cooled Reactors. Currently, many studies has been conducted in laboratory-scale for mod. 9Cr-1Mo steels. However, there is a lack of the study on forged thick- section for RPVs. The differences in characteristics including the through thickness microstructure and mechanical properties between internal and external locations may occur during cooling after austenitization, because the thickness of RPVs is over about 200mm. Therefore, in order to use ferritic/martensitic steel as RPVs, a detailed assessment of the through thickness properties is needed. The purpose of this study is ...

UK PubMed Central (United Kingdom)

The rice blast resistance (R) gene Pi-ta mediates gene-for-gene resistance against strains of the fungus Magnaporthe grisea that express avirulent...Full Text Available

Science.gov (United States)

Not Available

UK PubMed Central (United Kingdom)

Objective: To investigate the mechanism of carbapenem resistance and the occurrence of plasmid-mediated quinolone resistance determinants qnr and aac(6′)-Ib-cr...Full Text Available

International Nuclear Information System (INIS)

Plasma immersion ion implantation (PIII) is an effective materials modification and synthesis technique but has seldom been applied to ceramic materials due to the high electrical resistance that reduces the ion bombardment energy and sometimes causes serious electrical arcing in the instrument. Even in cases where PIII is applicable, the surface properties of the implanted insulating materials can be seriously affected due to the low ion energy and materials damage from electrical arcing. In order to enhance the surface and mechanical properties such as wear resistance of ceramic materials used in many industrial applications, surface modification is needed. In this work, we conduct carbon implantation into sintered #alpha#-SiC (silicon carbides that are widely used in vacuum ceramic bearings) using mesh-assisted plasma immersion ion implantation to enhance the surface properties. The use of a conducting grid is necessitated by the high ...

Science.gov (United States)

Scratch and Corrosion Resistance of an Aluminum Flange with an Electron Beam Modified Seal Edge

Science.gov (United States)

The emergence of bacterial antibiotic resistance is a growing problem, yet the variables that influence the rate of emergence of resistance are not well understood. In a microfluidic device designed to mimic naturally occurring bacterial niches, resistance of Escherichia coli to the antibiotic ciprofloxacin developed within 10 hours. Resistance emerged with as few as 100 bacteria in the initial inoculation. Whole-genome sequencing of the resistant organisms revealed that four functional single-nucleotide polymorphisms attained fixation. Knowledge about the rapid emergence of antibiotic resistance in the heterogeneous conditions within the mammalian body may be helpful in understanding the emergence of drug resistance during cancer chemotherapy. PMID:21940899

International Nuclear Information System (INIS)

Full text: Many factors including drug efficacy, compliance and antibiotic resistance may influence HP eradication rates. The "1"4C urea breath test is a sensitive method of confirming HP colonisation and eradication. The aim was to study the relationships between the peak "1"4CO_2 counts on the breath test prior to treatment, smoking and HP eradication, and to assess if persistent or recurrent symptoms implied failure of eradication. 117 patients with DU and HP colonisation proved on biopsy or rapid urease test who underwent "1"4C urea breath tests at least one month after eradication treatment was ceased were studied (69 male, 48 female, mean age 41, range 26-87 y). Questionnaire assessment of treatment regimen, smoking history and dyspeptic symptoms was made at the time of the breath test. A sub-group of 43 patients who had pre- and post-treatment breath tests was studied to assess if high peak ...

British Library Electronic Table of Contents (United Kingdom)

Statement of problem The use of titanium has increased for metal ceramic restorations, as well as for use in titanium implants, with developments in CAD/CAM technology. Some surface treatments of titanium have been introduced to enhance the titanium bond strength to low-fusing porcelains; however, a more reliable, easily used dental laboratory method has not been established. Purpose The purpose of this study was to compare the effect of laser etching as a titanium surface treatment with 3 other surface treatments (machining, airborne-particle abrasion, and acid etching), evaluating their ability to enhance the bond strength between a titanium substrate and porcelain. Material and methods A total of 64 specimen rods of commercially pure titanium (ASTM grade 2, 20 mm in length and 5.7 mm in...

Energy Technology Data Exchange (ETDEWEB)

Polyethylene (UHMWPE) wear in current knee prosthesis causes prosthesis loosening after no more than 15 years. In this work, a steady state one-dimensional lubrication model with non- Newtonian fluid, porous elastic layer on tibial component, ultra-filtration mechanism of fluid and some features of the surface roughness is studied through a numerical technique based on the Finite Element Method. The results show that the UHMWPE stiffness makes difficult the lubrication mechanism of the artificial joint and promotes abrasive and fatigue wear. Nevertheless, the use of compliant porous materials on the tibial component could reduce friction and wear. Moreover, the ultra-filtration mechanism promotes efficiency on the joint.

International Nuclear Information System (INIS)

Analyses of the roles of cement-based barriers in radioactive waste isolation show that models used to estimate their characteristics during the lifetime of the repository must consider the alteration of material properties with time due to degradation processes. Reinforced concrete barriers at repositories shall be designed in such manner that they fulfil besides isolative capabilities also the required functions of mechanical resistance and stability. Key elements of safety evaluation are mainly the correct selection of materials for mineral composites with cement binder (cements, aggregates, mineral additives and chemical admixtures) and their design, execution of construction works and production of precast concrete containers (continuous casting of concrete - no cold joints, limited number of construction joints, proper placing and consolidation, finishing and curing), strict control of used materials and inspection of works, as well as investigation after the ...

Energy Technology Data Exchange (ETDEWEB)

Five corrosion probes were received from West Valley Nuclear Services for evaluation in simulated tank 8D-2 3rd-stage sludge wash slurry. The same waste slurry simulated was also used in a series of ongoing corrosion studies assessing the effects of in-tank sludge washing on the integrity of tank 8D-2. Two of the corrosion probes were installed in the coupon corrosion test vessels operating at {approximately}150{degrees}F to compare performance of the probes with that observed by coupon tests conducted in the same vessels. Corrosion rate data calculated from electrical resistance measurements of the corrosion probes were evaluated for this study using two slightly different approaches. One approach uses the total length of exposure of the probe to give a ``time-averaged`` value of the corrosion rate. The other approach uses a shorter period of time (relative to the length of the test) in the calculation of corrosion rate, and is referred to as ...

International Nuclear Information System (INIS)

Past elastic-plastic fracture studies for leak-before-break (LBB) assessment of low alloy steel pipings have been focused mostly on the behavior of base metals and their weld metals. In contrast, the heat-affected zone (HAZ) of a welded pipe has not been studied in detail primarily because the size of the HAZ is too small to make specimens for mechanical properties measurements. In this study, microstructural analyses, microhardness tests, tensile tests and J-R tests have been conducted as a function of distance from a fusion line and temperature for HAZ materials of SA106Gr.C low alloy piping steels. For the ferrite-pearlite steels such as SA106Gr.C, the HAZ specimens showed a higher yield strength and fracture toughness compared with those of its base metal. These characteristics, despite of grain coarsening, can be explained by cleaner microstructures of HAZ materials with a finer morphology of carbides compared with pearlitic-ferritic base metals. However, the ...

Energy Technology Data Exchange (ETDEWEB)

The proper selection of materials of construction is necessary to provide process equipment with optimum performance and corrosion resistance. If properly chosen, the selected material should deteriorate at a uniform, predictable rate, which will allow for maintenance or replacement at scheduled intervals. This concept of risk assessment for predictive maintenance is a minimum requirement for proper materials selection. Materials selection is based on prior service history, field corrosion tests, pilot-plant tests, and laboratory bench-top tests--in that relative order of usefulness. Corrosion test methods are usually divided into two groups: laboratory and field (plant-site) tests. The main difference between the two is that field test specimens are exposed to actual process conditions will all of the variables involved, while laboratory tests are a simulation of field conditions, even if actual process fluids are involved. The paper ...

Energy Technology Data Exchange (ETDEWEB)

A set of materials property data for potential wear resistant materials was collected. These materials are designated for use as the ''core'' materials in the Fibrous Monolith structure. The material properties of hardness, toughness, thermal conductivity and cost were selected as determining factors for material choice. Data for these four properties were normalized, and weighting factors were assigned for each property to establish priority and evaluate the effects of priority fluctuation. Materials were then given a score based on the normalized parameters and weighting values. Using the initial estimates for parameter priority, the highest ranking material was tungsten carbide, with diamond as the second ranked material. Several materials were included in the trade study, and five were selected as promising ''core'' materials to include in this effort. These materials are tungsten carbide, ...

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than untreated Fe-20Cr-4V, 2205, and 904L metal ...

UK PubMed Central (United Kingdom)

Bloodstream infection by highly antibiotic-resistant bacteria, such as vancomycin-resistant Enterococcus (VRE), is a growing clinical problem that increasingly defies medical intervention....Full Text Available

UK PubMed Central (United Kingdom)

Antimicrobial resistance is an emerging problem with Pseudomonas aeruginosa. This study determined risk factors for the recovery of piperacillin-tazobactam-resistant P. aeruginosa...Full Text Available

UK PubMed Central (United Kingdom)

Purpose of reviewPhysicians, researchers and policy makers must understand the myriad consequences of multidrug and extensively drug-resistant tuberculosis (TB) within...Full Text Available

UK PubMed Central (United Kingdom)

The direct detection of pyrazinamide resistance in Mycobacterium tuberculosis is sufficiently difficult that many laboratories do not attempt it. Most pyrazinamide resistance is caused...Full Text Available

UK PubMed Central (United Kingdom)

Longitudinal electrical resistances have been measured on 2-centimeter segments of corn (Zea mays L.) roots, cut at varying distances from the root apex. The segment resistances vary...Full Text Available

UK PubMed Central (United Kingdom)

The antibiotic resistance patterns of gram-negative fecal bacteria from pigs in three herds with different histories of antibiotic exposure were examined. In general, smaller proportions of antibiotic-resistant...Full Text Available

UK PubMed Central (United Kingdom)

The author reviews the growth of the insecticide-resistance problem throughout the world during the period between July 1956 and November 1957, and the developments in research on the subject during...Full Text Available

UK PubMed Central (United Kingdom)

Summary: The increasing emergence of antimicrobial-resistant organisms, especially methicillin-resistant Staphylococcus aureus (MRSA), has resulted in the increased...Full Text Available

UK PubMed Central (United Kingdom)

In order to provide a rational basis for the development of new insecticides, a thorough understanding of resistance mechanisms is necessary and this presupposes a detailed knowledge of the normal...Full Text Available

UK PubMed Central (United Kingdom)

Individual strains of the plant pathogenic bacterium Pseudomonas syringae vary in their ability to produce toxins, nucleate ice, and resist antimicrobial compounds. These phenotypes...Full Text Available

UK PubMed Central (United Kingdom)

In this work we conducted both in vitro and in vivo experiments to examine the development and mechanisms of erythromycin (Ery) resistance in Campylobacter jejuni and Campylobacter...Full Text Available

UK PubMed Central (United Kingdom)

We compared the incidence of nasopharyngeal colonization by Streptococcus pneumoniae, the serotypes causing mucosal and invasive diseases, and the antibiotic resistance of these strains...Full Text Available

UK PubMed Central (United Kingdom)

Introduction:The purpose of this study was to utilize an in vitro biofilm model of subgingival plaque to investigate resistances in subgingival biofilm...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Contamination of the lube-oil with hard abrasive particles leads to a three-body abrasive wear mechanism that highly accelerates piston ring/cylinder liner wear in coal-fueled diesel engines. One approach to reducing that wear is to modify the size and orientation of surface asperities on the cylinder to enhance the formation of a hydrodynamic film, and to provide avenues of escape for particles that would otherwise be trapped in the wear zone. Another approach is to introduce additives into the contaminated lube-oil that further enhance hydrodynamic film formation, form chemical films on the wearing surfaces, or form films on the contaminant particles. This work focuses on defining the effects of cylinder liner surface finish, various configurations of slots in the cylinder liner surface, and various additives in the contaminated lube-oil on the wear process. Wear tests were initiated in a bench apparatus using coal-ash contaminated lube-oil ...

International Nuclear Information System (INIS)

Processing certain raw materials containing natural radioactive isotopes (e.g. U-238, Th-232 or K- 40) into products such as glas, abrasives, grinding materials or electrodes used for gasshielded tungsten-arc welding also leads to certain concentrations of industrial waste containing natural radioactive materials. Such industrial waste does not necessarily contain natural radioactive substances in concentrations exceeding the highest possible levels but nevertheless in significantly measurable quantities. This, however, frequently leads to confusion bordering on irritation by entities processing such substances as well as the general public, since they tend to believe natural radioactive substances in unobjectable concentration to cause similar or identical - health - consequences as man made radioactive substances in detrimental concentration. Radioactive materials may be incorporated intentionally or unintentionally into the product as main or additional ...

Science.gov (United States)

PMID:15675751

Science.gov (United States)

PMID:20681969

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Necessary theoretical foundation is given for the treatment of magnetic stresses applied to

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Wastenet

colonies known as biofilms are known to harbour food-borne pathogens . These biofilms also have an increased resistance

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

We quantified the resistance levels of transgenic rice plants, expressing Myxococcus xanthus protoporphyrinogen oxidase (PROTOX) in chloroplasts and mitochondria, to PROTOX inhibitors, acifluorfen, oxyfluorfen, carfentrazone-ethyl, and oxadiazon. We also determined whether active oxygen species-scavenging enzymes are involved in the resistance mechanism of transgenic rice. The transgenic rice line M4 was about >200-fold more resistant to oxyfluorfen than the wild-type (WT). M4 was also resistant to acifluorfen, carfentrazone-ethyl, and oxadiazon, but did not show multiple resistance to imazapyr and paraquat, which have different target sites. Acifluorfen, oxyfluorfen, carfentrazone-ethyl, and oxadiazon reduced the chlorophyll content in leaves of WT, but had minimal or no effect on M4. The...

Science.gov (United States)

NASA cost-risk assessment is composed of cost estimating relationship (CER) and technical risk assessment plus cost element correlation assessment; ...

Energy Technology Data Exchange (ETDEWEB)

In this article, a continuous stabilization process was used to make flame resistant fibers from polyacrylonitrile (PAN) fibers. The effect of the stabilization time and the stretching process during the stabilization process on the physical properties and flammability of the resultant flame resistant fibers was studied. Increased drawing of PAN fibers during the continuous stabilization process was found to decrease the diameter and increase the tensile strength in the resultant flame resistant fibers. These fibers also had higher density. There were no absolute relationships seen between flame-resistance and the formation of stable ladder polymers, density, and oxygen content. ((orig.))

International Nuclear Information System (INIS)

Corrosion testings of model alloys, corresponding by chemical composition to simple and complex-alloyed #gamma#- and #gamma#'-phases of nickel heat-resistant alloys are conducted in sodium sulfate and chloride melts. It is ascertained that heat resistant nickel alloys containing over 50 % of hardening #gamma#'-phase, are subject to disastrous sulfide corrosion (SC). Resistance against SC alloys containing below 50 % of #gamma#'-phase is determined by the resistance of #gamma#-solid solution. 10 refs., 3 figs., 2 tabs.

CSIR Research Space (South Africa)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

For several decades, ceramic matrix composite have been attracted attention in advanced structural and tribological applications. Advanced structural ceramics are presently used in diverse tribological applications such as tips for ballpoint pens, precision instrument bearings and cutting tools inserts. Design and selection of ceramics for these applications require reliable data on the effects of temperature, load and environment on the tribological behavior of these ceramics. In the present work, #alpha#-sialon matrix composites reinforced with different amounts of #beta#-sialon fibers were produced with the aim of improving their toughness to increase the industrial applications. The wear properties of #alpha#-sialon matrix composites were evaluated by carried out wear tests using a pin-on-disk tribometer under dry conditions. The #alpha#-sialon matrix composites were manufactured by slip casting and sintered by uniaxial hot pressing. Scanning electron microscopy, and energy ...

Energy Technology Data Exchange (ETDEWEB)

On March 28, 1979, the Pennsylvania Three Mile Island nuclear power plant Unit 2 (TMI-2) suffered a partial fuel-melt accident. During this accident, over 20,000 lb of molten fuel flowed through holes melted through the baffle plates and through the lower-core support assembly (LCSA). The molten fuel subsequently resolidified in the bottom of the reactor vessel. The lower-core support assembly of the TMI-2 reactor was not structurally damaged during the accident. In order to permit defueling of that region of the core, the LCSA was cut to permit access. A five-axis teleoperator was developed to deliver plasma arc cutting, rotary grinding and abrasive waterjet cutting of end effectors to the LCSA. Complex geometry sectioning was completed in a mock-up facility at chemistry and pressure conditions simulating those of the vessel, prior to actual in-vessel operations. In-vessel activities began in early May 1988 and were completed on April 11, 1989. This paper presents ...

Energy Technology Data Exchange (ETDEWEB)

The drilling rate of rotary percussion drill bit depends on the revolving energy and the impact energy of drifter as well as the characteristics of rock mass. The rotary percussion drill tests were executed in-situ for 13 kinds of rock mass using 12 actual drill machines to clarify the interrelations between them. At the result, the drilling rate has been expressed as the function of the revolving energy, the impact energy, the bit diameter, the coefficient of crack of rock mass and the Shore hardness or the amount of Los Angeles abrasion or the radial compressive strength of rock specimen. On the other hand, the rock mass properties could be determined by measuring the drilling rate of a standard rotary percussion drill machine. The relationship between the different drilling thrusts and the impact energy has been revealed. As a result, it has been found that the impact energy exerts a greater influence on the drilling rate than the revolving energy. (6 figs, 3 ...

Energy Technology Data Exchange (ETDEWEB)

Molecular imaging represents a modern research area that allows the in vivo study of molecular biological process kinetics using appropriate probes and visualization methods. This methodology may be defined- apart from the contrast media injection - as non-abrasive. In order to reach an in vivo molecular process imaging as accurate as possible the effects of the used probes on the biological should not be too large. The contrast media as important part of the molecular imaging can significantly contribute to the understanding of molecular processes and to the development of tailored diagnostics and therapy. Since more than 15 years PTB is developing optic imaging systems that may be used for fluorescence based visualization of tissue phantoms, small animal models and the localization of tumors and their predecessors, and for the early recognition of inflammatory processes in clinical trials. Cellular changes occur during many diseases, thus the molecular imaging ...

Energy Technology Data Exchange (ETDEWEB)

Development was explained of non-phosphate detergent with zeolite (Z) and alpha-olefin sulfonate (AOS). 4A type Z was taken notice of as a builder to replace phosphate. In calcium ion trapping power, conventional sodium tripolyphosphate (STP) and Z are 158mgCaO/g and 150mg/g, respectively. However, because Z by the conventional method is large in crystal diameter, coagulates and adheres to matter to be washed, was newly developed fine Z, 0.9 {mu} m in primary grain diameter, which does not give abrasion nor occlusion to the washing machine, nor precipitate in the river. Because linear alkylbenzene sulfonate, combined with Z, is poorer in washing power than that, done with STP, was developed AOS, new non-phoshate use interfacial active detergent, which is excellent in all washing power, biodegradation speed and physical powder property. Improvement was variously made also in powdery detergent production technology. Though the non-phosphate detergent controlled water ...

International Nuclear Information System (INIS)

Zirconium is a transition element located along with sister elements titanium and hafnium in Group IVB of the periodic table. It is grayish white metal, with a density somewhat less than carbon steel. Zirconium is the ninth most common metallic element in the earth's crust, and is more abundant than zinc, lead, nickel, or even copper. Zirconium is exceptionally resistant to corrosion by many common acids and alkalis. It is resistant to most organic acids, such as formic, acetic, lactic, and oxalic acids. It also has a high resistance to localized forms of corrosion, such as pitting, crevice corrosion, and stress corrosion cracking. Its corrosion resistance is caused by the formation of a dense, tenaciously adherent, chemically inert oxide film on the surface. This oxide film protects the base metal from both chemical and mechanical attack at temperatures up to about 400 C (750 F). This article describes ...

British Library Electronic Table of Contents (United Kingdom)

Globodera rostochiensis and Globodera pallida are parasitic root cyst nematodes of potato (PCN), which significantly reduce yield and quality. The genetics and available molecular markers should make resistance to nematodes an excellent candidate for marker assisted selection. The study presents results of testing the suitability of known molecular markers for detection of resistance in a set of cultivars. We revealed some inconsistencies in genealogical data of the cultivars and showed inconsistent usefulness in detecting resistant cultivars. The marker TG689 was identified in almost all cultivars resistant to G. rostochiensis and together with other markers was used for verifying the resistance in a group of breeding lines. The marker TG689 was the most effective. However, the efficiency...

UK PubMed Central (United Kingdom)

Transformed Drosophila Kc cell lines, resistant to methotrexate, an inhibitor of de novo purine and pyrimidine synthesis, have been obtained by calcium phosphate transfection of plasmids containing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

By isomorphous replacement of silicon by phosphorus the authors have synthesized crystalline aluminosilicophosphates with structures of the zeolites type A and faujasite. They determine the adsorption capacity of specimens treated at 575-1275/sup 0/K. They show that the thermal stability and acid resistance of aluminosilicophosphates depend on the quantity of phosphorus in their structure.

UK PubMed Central (United Kingdom)

A copper-resistant strain (09906) of Pseudomonas fluorescens that was isolated from a citrus grove soil is being investigated as a biological control agent for Phytophthora root rot. Since citrus grove...Full Text Available

UK PubMed Central (United Kingdom)

The pyrethroid knockdown resistance gene (kdr) has become widespread in Anopheles gambiae in West Africa. A trial to test the continuing efficacy of insecticide-treated...Full Text Available

UK PubMed Central (United Kingdom)

Resistance (R) protein mediated recognition of pathogen avirulence effectors triggers signaling that induces a very robust form of species-specific immunity in plants. The soybean Rpg1-b protein mediates...Full Text Available

Science.gov (United States)

Link to USGS home page Results of Electrical Resistivity Data Collected near the Town of Guernsey, Platte County, Wyoming By Robert R. McDougal, Jared D. Abraham, and Robert J....

Science.gov (United States)

Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

UK PubMed Central (United Kingdom)

Cross-resistance to cefoxitin (FOX), chloramphenicol (CMP), and quinolones (nalidixic acid [NAL]) related to a putative efflux system overexpression has recently been reported for Klebsiella...Full Text Available

UK PubMed Central (United Kingdom)

Infection due to multidrug resistance pathogens is difficult to manage due to bacterial virulence factors and because of a relatively limited choice of antimicrobial agents. Thus, it is imperative to...Full Text Available

UK PubMed Central (United Kingdom)

Juvenile hormone analog (JHA) insecticides are relatively nontoxic to vertebrates and offer effective control of certain insect pests. Recent reports of resistance in whiteflies and mosquitoes demonstrate...Full Text Available

UK PubMed Central (United Kingdom)

Insulin resistance in skeletal muscle is a key phenotype associated with type 2 diabetes (T2D) for which the molecular mediators remain unclear. We therefore conducted an expression analysis of human...Full Text Available

UK PubMed Central (United Kingdom)

Extended-spectrum beta-lactamases (ESBL) constitute a key antibiotic-resistance mechanism affecting Gram-negative bacteria, and also an excellent model for studying evolution in real time. A shift in...Full Text Available

UK PubMed Central (United Kingdom)

We compared MRSA Select to mannitol-salt agar with 8 μg/ml cefoxitin for the detection of methicillin-resistant Staphylococcus aureus (MRSA) from 6,199 clinical...Full Text Available

UK PubMed Central (United Kingdom)

Denaturing high-performance liquid chromatography (DHPLC) has been used extensively to detect genetic variation. We used this method to detect and identify Yersinia pestis KIM5 ciprofloxacin-resistant...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundThe emergence of plasmid-mediated carbapenemases, such as NDM-1 in Enterobacteriaceae is a major public health issue. Since they mediate resistance to...Full Text Available

UK PubMed Central (United Kingdom)

Objective:To estimate the prevalence of insulin resistant syndrome (IRS) among newly diagnosed patients with type 2 diabetes and to test their validity against two indices...Full Text Available

Science.gov (United States)

... Axial Waterjet (AxWJ) Model 5662: 0 Hull Resistance and Model-Scale Powering C with LDV Nozzle Design CO By C ClC ...

UK PubMed Central (United Kingdom)

BackgroundMany commercial banana varieties lack sources of resistance to pests and diseases, as a consequence of sterility and narrow genetic background. Fertile wild relatives,...Full Text Available

UK PubMed Central (United Kingdom)

Acquired resistance to the action of insulin to stimulate glucose transport in skeletal muscle is associated with obesity and promotes the development of type 2 diabetes. In skeletal muscle,...Full Text Available

UK PubMed Central (United Kingdom)

Reciprocal mass crosses and back-crosses were performed between two homogeneous strains of the housefly (Musca domestica L.), representing the extremes in susceptibility and resistance...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundInsecticide-based methods represent the most effective means of blocking the transmission of vector borne diseases. However, insecticide resistance poses a serious threat...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We wanted to evaluate the status of self-expandable nitinol stents implanted in the P2 and P3 segments of the popliteal artery in Korean patients. We retrospectively analyzed 189 consecutive patients who underwent endovascular treatment for steno occlusive lesions in the femoropopliteal artery from July 2003 to March 2009, and 18 patients who underwent stent placement in popliteal arterial P2 and P3 segments were finally enrolled. Lesion patency was evaluated by ultrasound or CT angiography, and stent fracture was assessed by plain X-rays at 1, 3, 6 and 12 months and annually thereafter. At the 1-month follow-up, stent fracture (Type 2) was seen in one limb (up to P3, 1 of 18, 6%) and it was identified in seven limbs at the 3-month follow-up (Type 2, Type 3, Type 4) (n = 1: up to P2: n = 6: P3). At the 6-month follow-up, one more fracture (Type 1) (up to P3) was noted. At the 1-year follow-up, there were no additional stent fractures. Just four limbs (up to P2) at ...

Energy Technology Data Exchange (ETDEWEB)

A comprehensive understanding of dopant activation mechanisms in crystalline Si is required in order to form shallow junctions. In this paper, we will review several experimental assessments on boron clustering and novel methods to form shallow junctions. Boron marker-layer structures have been used to investigate the fundamental aspects of formation and ripening boron-interstitial clusters (BICs) and their influence on the associated transient enhanced diffusion (TED). The samples were damaged by Si implants at different doses in the sub-amorphizing range and annealed at high temperatures. We found that BICs act as a sink for interstitials at supersaturations values S(t)>10{sup 4}. This implies that silicon self-interstitial defects are the primary source of interstitials driving TED, and that BICs act as a secondary 'buffer' for the interstitial supersaturation. These clusters are less sensitive to the ripening process than pure ...

Science.gov (United States)

Gas evolution in aluminum electrolytic capacitors constitutes one of their main drawbacks in comparison to other types of capacitors lacking a liquid electrolyte. In this respect, one of the most common causes of failure shown by liquid electrolyte capacitors is electrolyte leakage through the seal or even explosions produced by internal pressure buildup. In order to prevent these hazards, some substances, known as depolarizers, are usually added to the capacitor electrolyte with the purpose of absorbing the hydrogen evolved at the cathode (1, 2). Although the gas evolution problem in electrolytic capacitors has been known for a long time, there is a lack of literature on both direct measurements of the gas evolved and assessments of the amount of depolarizer active for the hydrogen absorption process. Aluminum electrolytic capacitors of 100..mu..F and 40V nominal voltage, miniature type (diam 8 mm, height 18.5 mm), were manufactured under standard specifications. ...

Science.gov (United States)

The sequencing and detailed comparative functional analysis of genomes of a number of select botanical models open new doors into comparative genomics among the angiosperms, with potential benefits for improvement of many orphan crops that feed large populations. In this study, a set of simple sequence repeat (SSR) markers was developed by mining the expressed sequence tag (EST) database of sorghum. Among the SSR-containing sequences, only those sharing considerable homology with rice genomic sequences across the lengths of the 12 rice chromosomes were selected. Thus, 600 SSR-containing sorghum EST sequences (50 homologous sequences on each of the 12 rice chromosomes) were selected, with the intention of providing coverage for corresponding homologous regions of the sorghum genome. Primer pairs were designed and polymorphism detection ability was assessed using parental pairs of two existing sorghum mapping populations. About 28% of these new markers detected ...

International Nuclear Information System (INIS)

Due to thermal gradients and load changes steam-turbine casings suffer combined creep-fatigue loading. Creep and fatigue portions depend on service conditions. Special interest is focused on the behaviour of creep-fatigue cracks, originated from potential defects due to construction and manufacturing weldments, on residual lifetime assessment. The project deals with the crack-growth behaviour at 530deg C and r.t. of welded and unwelded heat-resistant cast steels: 1% CrMoV-cast (GS-17 CrMoV 5 11, two melts: low and high V-content) and 12% CrMoV-cast (G-X 22 CrMoV 12 1). The crack planes of CT-specimens investigated, taken from manual arc-welded plates, were situated in the heat-affected zone (HAZ). The fatigue, creep and combined creep-fatigue crack-growth behaviour was investigated by means of low-frequency (0.5 and 0.05 Hz) tests, holding-time (20 min) tests and constant load tests up to about 5 000 h. Metallographic investigations show that ...

International Nuclear Information System (INIS)

Metal waste generated from domestic nuclear operation for defense and commercial application has led to a growing stockpile of radioactively contaminated scrap metal, much of which is stainless steel. A significant fraction of this material cannot be efficiently surface decontaminated. The burial of this material would be wasteful and expensive, since long term monitoring would be necessary in order to minimize environmental risk. Much of this waste consists of bulky equipment. In many case, this equipment contains valuable material that may be recycled. The piece of equipment considered frequently also has complex geometries, making extremely difficult, time-consuming and expensive to determine the exact location and level of radioactivity on the internal surfaces. After melting, however, the radioactivity may be precisely determined from samples of each ingot. Moreover, an ingot may be released for restricted or unrestricted reuse, or stored for decay to appropriated limits. Melting ...

Science.gov (United States)

... The micrometeorological community often expresses these relations in resistance law terms (Garratt and Hicks, 1973; Hicks et al., 1985) ...

International Nuclear Information System (INIS)

17-4PH stainless steel was modified by direct current (DC) plasma nitriding and titanium nitride film duplex treatment in this study. The microstructure, wear resistance and corrosion resistance were characterized by X-ray diffraction (XRD), pin-on-disk tribological test and polarization experiment. The results revealed that the DC plasma nitriding pretreatment was in favor of improving properties of titanium nitride film. The corrosion resistance and wear resistance of duplex treatment specimen was more superior to that of only coated titanium nitride film.

Science.gov (United States)

... Abstract : Two traces in flexible cables used in the Milstar agile beam antenna system failed during acceptance testing. ...

Science.gov (United States)

PMID:17346598

Science.gov (United States)

increase of pedel force; or amount of resistance to deflection. This result is in agreement wi"& the results of tests made on the ...

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

We show that the eigenvalue equations describing a cylindrical ideal magnetophydrodynamicsw (MHD) plasma interacting with a thin resistive wall can be put into the standard mathematical form: ??? = ??? ?. This is accomplished by using a finite element basis for the plasma, and by adding an extra degree of freedom corresponding to the electrical current in the thin wall. The standard form allows the use of linear eigenvalue solvers, without additional interations, to compute the complete spectrum of plasma modes in the presence of a surrounding restrictive wall at arbitrary separation. We show that our method recovers standard results in the limits of (1) an infinitely resistive wall (no wall), and (2) a zero resistance wall (ideal wall).

Science.gov (United States)

... The maximum rate-of-deflection is not&d to decresse with increase of pedel force; or amount of resistance to deflection. ...

Energy Technology Data Exchange (ETDEWEB)

Resistance of ALLOY 800 as a PWR/SG tubings to IGC/IGSCC and Ni, Co release into high temperature water was evaluated as compared with ALLOYs 600 and 690. The study to improve the resistance to IGSCC and general corrosion was also made. From the results, ALLOY 800 was evaluated to be the most reliable among the high Ni alloys tested. In addition, the alloy would obtain further reliability in IGSCC and general corrosion resistance by the combined addition of Ti and Nb, and the prior oxidation treatments, respectively. (author).

Science.gov (United States)

... populations ..... 63 34 Vertebral ultimate compressive strength for various populations ..... 64 35 ...

Science.gov (United States)

... HIGH FREQUENCY, WIRE, ATMOSPHERIC MOTION, SENSITIVITY, PLATINUM, FREQUENCY RESPONSE, AMPLIFIERS, MULTIVIBRATORS. ...

Science.gov (United States)

Megasphaera elsdenii is a lactate-fermenting, obligately anaerobic bacterium commonly present in the gastrointestinal tracts of mammals, including humans. Swine M. elsdenii strains were previously shown to have high levels of tetracycline resistance (MIC = 64->256 micro g/ml) and to carry mosaic (re...

International Nuclear Information System (INIS)

The pitting corrosion resistance of three different types of stainless steel implanted with silicon is investigated using the potentiokinetic polarization technique. The specimens are tested in 3% NaCl and 0.1 N HCl solutions. Silicon ion implantation inhibits pitting corrosion of the steels in both aqueous media. The corrosion resistance depends on the silicon dose. Post implantation annealing only slightly alters the localized corrosion. (author).

Energy Technology Data Exchange (ETDEWEB)

A composition of matter to treat particles entrained in flue gas, is described comprising: a caustic liquid used to adjust resistivity of the entrained particles; and inert particulate matter supporting the caustic liquid for inhibiting chemical action of the caustic liquid until used to adjust the resistivity of the entrained particles, the inert particulate matter supporting sufficient caustic liquid to adjust the resistivity of the entrained particles.

UK PubMed Central (United Kingdom)

A nationwide antimicrobial resistance surveillance has been conducted since 1997 in Korea. In this study, susceptibility test data generated in 2004 by KONSAR group hospitals were analyzed and compared...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This document, the Standards/Requirements Identification Document (S/RID) Phase 2 Assessment Report for the subject facility, represents the results of a Performance Assessment to determine whether procedures containing S/RID requirements are fully implemented by field personnel in the field. It contains a summary report and three attachments; an assessment schedule, performance objectives, and assessments for selected functional areas.

British Library Electronic Table of Contents (United Kingdom)

Resistive switching memory is a very promising technology for emerging nonvolatile memory applications. Generally, the switching behavior is triggered by a sweep or pulse voltage. In this paper, a charged capacitor is proposed to be used as the external electrical source to program a resistive switching element. From theoretical analyses based on a set behavior model, the capacitor approach can program the device efficiently. Compared with sweep or pulse mode, capacitor driving method can greatly reduce over-programming after the set event, and thus improve the resistance uniformity. The experimental results performed on Cu/ZrO2:Cu/Pt device support this conclusion quite well. The proposed methodology has great value for achieving a reliable resistive switching, which is important for high...

British Library Electronic Table of Contents (United Kingdom)

This study compares two series of solvents for application in aluminum electrolytic capacitors: ethylene glycol (EG) and water mixtures, and ethylene glycol and 1-n-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF4) ionic liquid (IL) mixtures. Electrochemical impedance spectroscopy and cyclic voltammetry were carried out with a previously anodized aluminum disk electrode. Comparative measurements of solution resistance, polarization resistance, AC capacitance, and passive current were made. The results show that EG?IL mixtures with low amounts of IL (10% IL?90% EG v/v) have a low solution resistance. Low values of solution resistance, high values of polarization resistance, small passive current, and uniform capacitance of anodized aluminum in EG?IL mixtures are favorable properties of ...

Energy Technology Data Exchange (ETDEWEB)

Soil electrical resistivity is perhaps the only soil parameter that is used by geologists and geotechnical engineers to explore the subsurface characteristics at a power plant site and also used by civil and electrical engineers as input to their design. A properly designed and executed field electrical resistivity survey is one method of examining the subsurface profile. The same program can provide information about the corrosion potential of the soil that can play a major role in determining the protection needed for buried steel piping and pile foundations. At the same time, the soil conductivity interpreted from the results of the resistivity testing is an integral part of the design of the electrical grounding system for the plant. This paper describes soil electrical resistivity, test procedures to estimate resistivity values, and how these values can best be used to obtain ...

British Library Electronic Table of Contents (United Kingdom)

This chapter provides a glimpse of student affairs assessment at Northern Arizona University including a specific example of assessment, tips to implementing assessment at your institution, and barriers encountered when implementing the process at Northern Arizona University.

UK PubMed Central (United Kingdom)

Behavioural assessment methods have been used to signal the need for intervention and to evaluate treatment effectiveness. Direct observation and rating scales have been used to assess pain and distress...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundComputer-based health-risk assessments are electronic surveys which can be completed by patients privately, for example during their waiting time...Full Text Available

Science.gov (United States)

The report gives an initial assessment of the feasibility of disposing of flue gas desulfurization wastes in mines and in the ocean. The purpose of the assessment was to evaluate environmental, technical, regulatory, and economic aspects of the use of such disposal sites. Availab...

UK PubMed Central (United Kingdom)

The evaluation of biological markers is recognized as necessary to the future of toxicology, epidemiology, and quantitative risk assessment. For biological markers to become widely accepted, their validity...Full Text Available

UK PubMed Central (United Kingdom)

Transtelephonic electrocardiographic transmission (TET) is the most widespread form of telecardiology since it enables clinicians to assess patients at a distance. The purpose of this study was to assess...Full Text Available

UK PubMed Central (United Kingdom)

ObjectivesTo determine the content and extent, design, and relative importance of patient assessment courses in the professional pharmacy curriculum.MethodsA...Full Text Available

Science.gov (United States)

... 1768 1475 360 to 3400 ... The TSC provided an independent assessment of SA based on ... Complexity of Situation Degree of complication (number of ...

Science.gov (United States)

assessment.Both frustumswerein excellentcondition.No missingTPSor debonds/ unbondswere ...... 2) The average time for a 360 degree rotation was 29.9 seconds. ...

British Library Electronic Table of Contents (United Kingdom)

Purpose - The purpose of this paper is to examine potential new uses of return on investment (ROI) in alternative methods for library assessment and valuation. Design/methodology/approach - Uses examples of recent uses of ROI by libraries to identify potential new applications of ROI in library assessment and valuation. Findings - ROI investment has historically been used by libraries for the assessment of past performance of library organizations in a reactive/defensive nature or for assessing the value of customer services. ROI has not been widely used as a proactive assessment tool, to introspectively assess administrative or other internal services, or as an offensive assessment and valuation tool, especially for intangible performance assessment and valuation. Originality/value - New ...

International Nuclear Information System (INIS)

The effect of phosphorus on the corrosion resistance of Al-bronzes is studied in detail in this work. A literature review showed that there are a lot of things known about the microstructure and the mechanical properties of Al-bronzes. In spite of their corrosion resistance the corrosion properties and the structure of the protective oxide films of Al-bronzes were seldom a matter of interest. Systematic studies of the influence of different alloying elements on the oxide film and the corrosion properties are rare. Therefore, it is not possible to predict the corrosion resistance of Al-bronzes, made by alloying particular elements. The high corrosion resistance of the new alloy CuAl_2_0P_1 was the reason to investigate the influence of phosphorus on the corrosion properties of Al-bronzes in more detail. A systematic study of the microstructure and the corrosion properties of Cu, CuP_x, CuAl_2_0 and ...

Energy Technology Data Exchange (ETDEWEB)

Specific {sup 32}P-labeled DNA probes were prepared and used to evaluate the distribution of tetracycline resistance determinants carried by gram-negative enteric bacteria isolated from pigs in 3 swine herds with different histories of antibiotic exposure. Plasmid DNA, ranging in size from 2.1 to 186 Kb, was observed in over 84% of 114 isolates studied. Two of 78 tetracycline resistant strains did not harbor plasmids. The DNA probes were isolated from plasmids pSL18, pRT29/Tn10, pBR322 and pSL106, respectively, and they represented class A, B, C and D tetracycline resistance determinants. Hybridization conditions using 0.5X SSPE at 65{degrees}C minimize cross-hybridization between the different class of tetracycline resistance genes. Cross-hybridization between class A and class C determinants could be distinguished by simultaneous comparison of the intensity of their hybridization signals. Plasmids ...

Energy Technology Data Exchange (ETDEWEB)

This paper states the concept of a heat-resistant structure of the HOPE airframe having a 10 ton weight when lifting off and also the research situation of heat-resistant structural materials. To study the structure, established are design conditions for lift-off, reentry to the atmosphere and landing. As to the load condition, the load at the time of lift-off is most critical. Relating to the temperature environment condition, thermal analysis is made of the time when a HOPE is on the orbit (low-temperature range) and reenters the atmosphere (high-temperature range), when the temperature environment is critical. The analysis shows that the temrerature environment is in a {minus}80-1700{degree}C (range). The heat-resistant structural materials are developed so as to meet these conditions. The paper describes distribution of the airframe surface temperature by aerodynamic heating at the reentry, conceptual figures of the ...

International Nuclear Information System (INIS)

Because of their austenitic-ferritic microstructures, duplex stainless steels offer a good combination of mechanical and corrosion resistance properties. However, heat treatments can lower the mechanical strength of these stainless steels as well as render them susceptible to intergranular corrosion (IGC) and pitting corrosion. In this study, a low-carbon (0.02%) duplex stainless steel is subjected to various heat treatments at 450 to 950 C for 30 min to 10 h. The heat-treated samples than undergo ASTM IGC and pitting corrosion tests, and the results are correlated with the microstructures obtained after each heat treatment. In the absence of Cr_2_3C_6 precipitation, #sigma#-phase precipitates render this duplex stainless steel susceptible to IGC and pitting corrosion. Even submicroscopic #sigma#-phase precipitates are deleterious for IGC resistance. Longer-duration heat treatments (at 750 to 850 C) induce chromium diffusion to replenish the ...

Science.gov (United States)

A discussion of some of the difficulties with previous analyses of the resistivity of A-15 compounds is given. Precise high-temperature data on ..cap alpha..-particle- and electron-damaged Nb/sub 3/Ge and Nb/sub 3/Sn samples with different defect concentrations are presented here and analyzed in a simple way with use of a phenomenological model based on the idea that the ideal resistivity must approach some limiting value in the regime where the mean free path becomes comparable to the interatomic spacing.

Energy Technology Data Exchange (ETDEWEB)

The resistance of six tropical hardwoods to fungal degradation by two wild-type strains of Phanerochaete chrysosporium Burdsall was investigated using vermiculite burial and wood-block weight loss techniques. Radiation-induced wood-polymer composites (WPC), based on two hardwoods Ramin and Rubberwood with methyl methacrylate, were prepared, and samples were also exposed to the wood-rotting fungus. A significant improvement in resistance to fungal decay was observed in the WPC. Scanning-electron micrographs of the two woods and their composites after fungal degradation are presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

The damage induced by low-temperature proton irradiation in amorphous Pd/sub 80/Si/sub 20/ prepared by ion implantation is studied via electrical resistivity measurements. Our experimental results concerning the initial damage rate and the resistivity saturation are compared to the results obtained for electron and high energy /sup 16/O irradiation of amorphous Pd/sub 80/Si/sub 20/ quenched from the melt. The resistivity curve is analyzed in terms of irradiation-induced point defects.

British Library Electronic Table of Contents (United Kingdom)

Resistance and tolerance are two types of host defense mechanisms that increase fitness in response to fungi. Several genetic polymorphisms in pattern recognition receptors, most remarkably Toll-like receptors (TLRs), have been described to influence resistance and tolerance to aspergillosis in distinct clinical settings. TLRs on dendritic cells pivotally contribute in determining the balance between immunopathology and protective immunity to the fungus. Epithelial cells also contribute to this balance via selected TLRs converging on indoleamine-2,3-dioxygenase (IDO). Studies in experimental hematopoietic transplantation confirmed the dichotomy of pathways leading to resistance and tolerance to the fungus providing new insights on the relative contribution of the hematopoietic/nonhematopoi...

British Library Electronic Table of Contents (United Kingdom)

Glabridin, an active constituent of Glycyrrhiza glabra roots, was found to be active against both yeast and filamentous fungi. Glabridin also showed resistance modifying activity against drug resistant mutants of Candida albicans at a minimum inhibitory concentration of 31.25-250 g/mL. Although the compound was reported earlier to be active against Candida albicans, but this is the first report of its activity against drug resistant mutants. Copyright Copyright 2009 John Wiley & Sons, Ltd.

Science.gov (United States)

PMID:7900316

Science.gov (United States)

PMID:21540757

International Science & Technology Center (ISTC)

Assessment of the Situation with Rabies in the Republic of Tajikistan and Organization of Activities on Rabies Control

KoreaScience (Korea)

Full Text Available

CSIR Research Space (South Africa)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

The Guarantee Outline presents the technical demands of design and contents of assessment for radiation hardening in satellite engineering in China. It includes the basis of design in space environment of polar orbit, the contents of design for general radiation hardening, the requirements and assessments of the single-board computer, the requirements of design for circuits (including hardware and software), the choices and assessments for devices, and the primary stipulations for the requirements of design and assessments against the phenomenon of charge and discharge.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

The chemiosmotic model of energy transduction offers a satisfying and widely confirmed understanding of the action of uncouplers on such processes as oxidative phosphorylation; the uncoupler, by facilitating...Full Text Available

Science.gov (United States)

... The addition of 0.5 pphr of fine thermal carbon black to the polymers gave good resistance to 500 hours of ultraviolet (UV) xposure in a Weather ...

Science.gov (United States)

... estrogen receptor status. Cancer Lett., 253, 291-300. 39. Xin,X ... and resistant mice. Brain Res.Bull., 52, 235-242. 40. Foster,BA ...

Energy Technology Data Exchange (ETDEWEB)

The electrical resistivity, Hall effect, and magnetic susceptibility of single-crystal UPd[sub 2]Si[sub 2] have been studied between 4.2 and 300 K. A large anisotropy was observed in both the magnetic and transport properties. There is a quadratic temperature dependence of the resistivity for a range of temperatures between 4.2 and 80 K. At higher temperatures, the resistivity indicates a Kondo-type behavior. The behavior of these quantities is accounted for by the magnetic phase transitions at 108 and 136 K reported from neutron-scattering studies. At high temperatures, the magnetic susceptibility of UPd[sub 2]Si[sub 2] is Curie-Wiess-like along the [ital c] axis. The temperature dependence of the Hall coefficient above 108 K is accounted for by a theoretical model invoking skew scattering of conduction electrons by localized magnetic moments.

British Library Electronic Table of Contents (United Kingdom)

The world of antibiotic drug discovery and development is driven by the necessity to overcome antibiotic resistance in common Gram-positive and Gram-negative pathogens. However, the lack of Gram-negative activity among both recently approved antibiotics and compounds in the developmental pipeline is a general trend despite the fact that the plethora of covered drug targets are well-conserved across the bacterial kingdom. Such intrinsic resistance in Gram-negative bacteria is largely attributed to the activity of multidrug resistance (MDR) efflux pumps. Moreover, these pumps also play a significant role in acquired clinical resistance. Together, these considerations make efflux pumps attractive targets for inhibition in that the resultant efflux pump inhibitor (EPI)/antibiotic combination d...

British Library Electronic Table of Contents (United Kingdom)

The regenerative-chatter resistance of a viscoelastic cantilever beam is analyzed and compared to the common dynamic vibration absorber (DVA) system. The beam represents a tool holder for turning operation in machining. The optimum structural parameters are found by maximizing the most negative real part of the frequency response function (FRF). The FRF is found analytically by using an appropriate Greens function. Keeping the cantilever static stiffness constant, further increase in the optimal resistance is achieved by changing the ratio between the two elastic moduli in the 3-parameter solid viscoelastic material model. Three additional chatter resistance indicators are also investigated: the most positive real part of the FRF, the magnitude of the FRF and the resonant frequency. It is ...

Science.gov (United States)

from the Clearinghouse for Federal Scientific and Technical Information, Springfield, Virginia 22151. Magnetic Forming of Resistive Materials ...

UK PubMed Central (United Kingdom)

BACKGROUNDNew diagnostic tools are urgently needed to interrupt the transmission of tuberculosis and multidrug-resistant tuberculosis. Rapid,...Full Text Available

International Nuclear Information System (INIS)

Laser surface modification can lead to formation of a novel microstructure on the surface of a material resulting in improved surface properties. During the past one and half decades, a number of investigations have been reported on laser surface modification techniques for improving the corrosion resistance of various materials. This paper reviews various work reported on utilising laser modification techniques for enhancing the aqueous corrosion resistance of materials. The laser surface modification work carried out on materials like stainless steels, C-steels, low alloy steels and non-ferrous materials such as Zr, Zn, Al, Ni, Mg and their alloys has been covered in the review. General features observed in improving the corrosion resistance after laser processing have been discussed and scope for future investigations in this field has been highlighted. (author). 97 refs., 15 figs., 5 tabs.

International Nuclear Information System (INIS)

The effect of alloying low carbon 18Cr-30Ni steel with silicon (up to 5.1%), copper (up to 5.4%), cobalt (up to 15.3%) on the resistance to corrosion cracking and pitting corrosion, is studied. Tests on uniaxial tension are carried out in 42% MgCl_2 solution and gravimetric studies in 10% FeCl_3x6H_2O. It is established that alloying steel of the Kh18N30 type with silicon increases strength and resistance to corrosion cracking. Copper and cobalt decrease a resistance to pitting corrosion but somewhat increase a resistance to corrosion cracking.

Science.gov (United States)

... 1. IE1O and IM'15 exposed to field corrosion tests at five sites for periods of 12 and 24 months confirm previous findings. ...

Norwegian Open Research Archives (NORA)

Full Text Available

UK PubMed Central (United Kingdom)

Rotifers of class Bdelloidea are common invertebrate animals with highly unusual characteristics, including apparently obligate asexuality, the ability to resume reproduction after desiccation at any...Full Text Available

Science.gov (United States)

... Abstract : The electric resistance in weak (diluted) solid solutions of the Pd-Ag and Fe-W systems, as wellAS THE Hall effect in a Pd-Ag system ...

Energy Technology Data Exchange (ETDEWEB)

Genes for chloramphenicol resistance, Cm(r) and tetracycline resistance, Tc(r), which are present as heterologous insertions in the chromosomes of some clinical isolates of Streptococcus pneumoniae (pneumococcus) and derivative strains, were transferred at a low frequency to other pneumococci by a DNase-resistant filter mating process that resembles conjugation. Cotransfer of Cm(r) and Tc(r) was the most common event. Neither the donor strains nor the transconjugants contained detectable plasmids. Transconjugants acted as donors for transformation and for filter mating and had properties similar to those of the parent strain. The presence of the conjugative plasmid pIP501 in the donor did not appear to influence the transfer properties of the Cm(r) or Tc(r) determinants.

International Nuclear Information System (INIS)

An Ultra-Low-Carbon 19% Cr-11% Ni Stainless Steels used in nuclear fuel reprocessing plants where highly corrosion resistance in nitric acid is required has been developed. This steel has optimized the chemistry composition to decrease inclusions and deformation-induced martensitic transformation. The formation of deformation-induced martensite has the potential danger of accelerating corrosion in nitric acid. In this paper, effects of cold reduction and martensitic transformation on corrosion resistance of Ultra-Low-Carbon Stainless Steels in nitric acid are discussed. The developed steel showed excellent corrosion resistance during long-term exposure to nitric acid. (author).

International Science & Technology Center (ISTC)

Corrosion- and Wear Resistant Silicon Containing Chromium-Manganese and Nickel-Chromium-Manganese Nonmagnetic Steels with Increased Strength and Toughness for Reliable Work at Normal and Cryogenic Temperatures

UK PubMed Central (United Kingdom)

Pathways of salicylic acid (SA) biosynthesis and metabolism in tobacco have been recently identified. SA, an endogenous regulator of disease resistance, is a product of phenylpropanoid metabolism formed...Full Text Available