This paper describes the method to estimate the true formation temperature using temperature recovery logging data after the well reach to total depth (T.D.). The method designated as ''Curve-fitting method (CFM)'' is based on mathematical model proposed by Middleton (1979, 1982). The accuracy and applicability of this method are evaluated with several field data and compared advantageously with the Horner-plot method. Then, real-time data acquisition system including interpretation software has also been successfully developed. As a conclusion, the followings are confirmed: (1) The developed CFM can be applicable to the estimation of the true formation temperature even using 24hours temperature recovery data, although the Horner-plot method might need up to 120 hours recovery data, ...
PurposeThis study evaluates changes in recall of combat exposures over the first year after return from deployment. The research purpose is to assess whether recall of combat exposures is consistent at different time points; if not, what demographic and/or PTSD symptom risk factors exist for any directional instability. MethodsSurveys completed by soldiers at 3, 6, and 12 months post-Operation Iraqi Freedom (OIF) deployment were linked for longitudinal analysis in a previous study in which three matched datasets were created: 3-6 months (N = 768), 6-12 months (N = 341), and 3-12 months (N = 445). Post-traumatic stress disorder (PTSD) was assessed by using the National Center for PTSD Checklist. The reliability of recall for 36 combat exposures was quantified. The effects of demographics an...
A new method of administration of an opioid was recently registered: fentanyl transdermal (brand name: Durogesic), intended particularly for the indication range 'pain in cancer'. Fentanyl is lipid-soluble so that deposition in the skin takes place and the biological half-life is approximately 20 hours after removal of the plaster. It is safe to start on a basis of an equianalgesic conversion of 100:1 in relation to oral morphine, although this may entail some risk of fentanyl under dosage. The dose adjustment time is 12-24hours before a constant fentanyl level is reached; therefore, after attaching the first sticking plaster, the original morphine dose should be continued for another 12 hours. In addition, the patient may, if necessary, be given supplementary morphine preferably as a short-acting drug. There seems to be no clear indication for transdermal fentanyl either in neuropathic pain or in chronic benign pain. ...
Background.There are no suitably powered epidemiological studies of `transient azotaemia' (TA). The objective of this study was to describe the epidemiology of TA and its independent association with hospital mortality. We hypothesized that TA would be associated with an independent increase in the risk of death. Methods.We retrospectively studied all patients admitted to a university-affiliated hospital in Australia between January 2000 and December 2002. Patients were excluded if they were <15 years old, were on chronic dialysis, had kidney transplant or if their length of hospital stay was <24hours. We defined TA as rapidly recovering acute kidney injury (AKI) (return to no-AKI risk, injury, failure, loss, end stage (RIFLE) class within 72 hours of onset). We performed descriptive and ...
3-Quinuclidinyl benzilate (QNB) is a potent muscarinic antagonist that binds to muscarinic acetylcholine receptors. Iodination of QNB is difficult because it contains rings that are deactivated, while phenol rings are activated. The purpose of this research is to develop an appropriate method for the iodination of QNB at no-carrier-added concentrations of /sup 125/I/NaI. Phenol was chose as the test compound for direct iodination by adding chloramine T and nonradioactive sodium iodide to the phenol in a phosphate buffer and methanol system. A simple method to radioiodinate QNB at several concentrations was developed in situ in the presence of QNB, thallic trifluoroacetate /sup 125/I/NaI, /sup 127/I/NaI, and aluminium chloride. Using milligram amounts of QNB (7.12 x 10/sup -6/ moles), three reaction steps were involved: QNB was reacted with thallic trifluoroacetate at 60/sup 0/C for 24hours, then ...
Purpose/Objective: The role of programmed cell death (apoptosis) as a cellular response to cancer therapy such as radiation or chemotherapy is the subject of much study, and manipulation of the apoptotic response in tumor cells may be valuable in the treatment of a variety of cancers. Both p53 dependent and independent apoptotic pathways have been identified; p53 is mutated in at least 50 % of human cancers and a majority of radiation resistant tumors contain p53 mutations. This study is designed to examine the induction of programmed cell death in a human colon carcinoma cell line that possesses two mutated p53 alleles. Ionizing radiation alone, or in combination with the chemotherapeutic drug 5-fluorouracil (5-FU), were used to elicit the apoptotic response. This study will focus on whether these treatments can induce a significant apoptotic response in cells that have mutated p53 alleles. Materials and Methods: HT-29 cells were assessed for clonogenic survival ...
Thirty-four patients with prostatic carcinoma were studied with quantitative bone scintigraphy and whole-body counting (WBC) 1 and 24 h after injection of [sup 99m]Tc-MDP before as well as two weeks and two months after orchiectomy. Thirteen of the patients had normal bone scintigrams and WBR at the three different investigations; 21 had skeletal metastases. The latter showed throughout the study higher local gamma camera count rates as well as WBR values than the patiens with normal scintigrams. In these patients a ''flare phenomenon'', with an increase in count rate two weeks after orchiectomy followed by a decrease two months post-operatively, was seen with quantitative bone scintigraphy but not with WBC. However, WBC may be a valuable method indicating the total extent of skeletal metastases in the body, while quantitative bone scintigraphy is more accurate in the interpretation of individual skeletal metastases. (orig.).
Thirty-four patients with prostatic carcinoma were studied with quantitative bone scintigraphy and whole-body counting (WBC) 1 and 24 h after injection of "9"9"mTc-MDP before as well as two weeks and two months after orchiectomy. Thirteen of the patients had normal bone scintigrams and WBR at the three different investigations; 21 had skeletal metastases. The latter showed throughout the study higher local gamma camera count rates as well as WBR values than the patiens with normal scintigrams. In these patients a ''flare phenomenon'', with an increase in count rate two weeks after orchiectomy followed by a decrease two months post-operatively, was seen with quantitative bone scintigraphy but not with WBC. However, WBC may be a valuable method indicating the total extent of skeletal metastases in the body, while quantitative bone scintigraphy is more accurate in the interpretation of individual skeletal metastases. (orig.).
The specific receptor sites and the endocytosis of transferrin (Tf) are evidenced in a cell line (HT-29) derived from a human colic adenocarcinoma by means of "1"2"5I radiolabeled Tf. The receptor density is studied in undifferentiated (UD) or differentiated (D) cells with respective doubling times of about 24hours and 46 hours. The number of binding sites for Tf is 162,000 (K_d = 7.8 nmol/l in ND cells and 68,000 (K_d = 7.40 nmol/l) in D cells. The distribution between the Tf bound to the cell surface and the internalized Tf is investigated by elimination of Tf bound to the surface by an acid wash method. The intracellular cycle of Tf seems to be characterized by a slower kinetics in UD cells. The high density of Tf receptor sites in HT-29 UD cells should allow the detection or the treatment of highly evolutive colic adenocarcinoma by means of Tf.
Plasma triglyceride turnover was measured during steady-state conditions in 22 postoperative patients. Nine had received nutritional support with an enteral regimen, seven had received an equivalent regimen as continuous parenteral nutrition, and six received the same parenteral regimen as a cyclical infusion. After 5 days of nutritional support, each patient received an intravenous bolus of tritiated glycerol. Plasma radiolabeled triglyceride content was measured during the subsequent 24hours. The data were analyzed by means of a simple deterministic model of plasma triglyceride kinetics and compared with the results obtained by stochastic analysis. The rates of hepatic triglyceride secretion obtained by deterministic analysis were higher than those obtained by the stochastic approach. However, the mode of delivery of the nutritional regimen did not affect the rate of hepatic triglyceride secretion regardless of the ...
The Purex process and the fluorescence spectrometry are first recalled, then uranyl fluorescence is studied in a pure nitric medium without other elements to establish a theoretical model, allowing the description of uranium fluorescence signal with a general equation. The influence of different parameters (temperature, inhibitors, dynamic quenching of iron and cerium) is investigated to develop the model. A quantitative analysis method without addition of reagents is proposed to validate the model.
The clinical signs and postmortem findings in sheep from two flocks accidentally poisoned with monensin are described. Clinical signs began within 24hours of exposure to monensin. In the acute stages...Full Text Available
We present a method for grouping the synonyms of a lemma according to its dictionary senses. The senses are defined by a large machine readable dictionary for French, the TLFi (Tr\\'esor de la langue fran\\c{c}aise informatis\\'e) and the synonyms are given by 5 synonym dictionaries (also for French). To evaluate the proposed method, we manually constructed a gold standard where for each (word, definition) pair and given the set of synonyms defined for that word by the 5 synonym dictionaries, 4 lexicographers specified the set of synonyms they judge adequate. While inter-annotator agreement ranges on that task from 67% to at best 88% depending on the annotator pair and on the synonym dictionary being considered, the automatic procedure we propose scores a precision of 67% and a recall of 71%. The proposed method is compared with related work namely, word sense disambiguation, synonym lexicon acquisition ...
Full text: DNA rearrangement events leading to chromosomal aberrations are central to ionizing radiation-induced cell death. Although DNA double-strand breaks are probably the lesion that initiates formation of chromosomal aberrations, little is understood about the molecular mechanisms that generate and modulate DNA rearrangement. Examination of the sequences that flank sites of DNA rearrangement may provide information regarding the processes and enzymes involved in rearrangement events. Accordingly, we developed a method using inverse PCR that allows the detection and sequencing of putative radiation-induced DNA rearrangements in defined regions of the human genome. The method can detect single copies of a rearrangement event that has occurred in a particular region of the genome and, therefore, DNA rearrangement detection does not require survival and continued multiplication of the affected cell. Ionizing radiation-induced DNA ...
Statement of problem Porcelain fracture associated with an implant-supported, metal ceramic crown or fixed partial denture occurs at a higher rate than in tooth-supported restorations, according to the literature. Implant-specific and patient-specific causes of ceramic failure have not been fully evaluated. Purpose The purpose of this retrospective study was to evaluate the potential statistical predictors for porcelain fracture of implant-supported, metal ceramic restorations. Material and Methods Over a 6-month period, a consecutive series of patients having previously received implant-supported, metal ceramic fixed restorations were examined during periodic recall appointments. The number of supporting implants, number of dental units, type of restoration, date of prosthesis insertion, ...
Six commercial insecticides viz., decis 25EC (deltamethrin), thiodan 35EC (endosulfan), curacron 500EC (profenophos), somialfa 110EC (esfenvalerate), denitol 30EC (fenpropathrin) and advantage 20EC (carbosulfan) were tested with recommended doses against first instar larvae of cotton bollworm, Helicoverpa armigera (Hub.) to determine their degree of toxicity under controlled laboratory conditions. Leaf dip method was applied for these tests. Insect mortality was assessed after 24, 48 and 72 hours of insecticide application. Results showed that curacron 500EC gave significantly high mortality of 100 % after 24hours of application followed by thiodan 35EC, somialfa 110EC and advantage 20EC causing 93, 80 and 72 % mortality, respectively. Whereas, denitol 30EC and decis 25EC showed the minimum, non-significant differences by giving mortality of 45 and 43 %, respectively. Effectiveness of all insecticides increased after 48 ...
Purpose: To evaluate MR imaging of the hip in patients with a clinically suspected impacted fracture of the femoral neck in cases where conventional plain films show negative or equivocal findings. Material and Methods: Twenty-seven such patients were prospectively examined by MR imaging with a 1.0 T unit, within 24hours of admittance to hospital. A coronal T1-weighted turbo spin-echo sequence (n=27), and a coronal STIR sequence (n=25) or a coronal T2-weighted turbo spin-echo fast saturation sequence (n=2) were used. The evaluations were made by 2 radiologists with experience in musculoskeletal radiology. Results: There were 6 patients with a petrochanteric fracture, 2 without and 4 with slight displacement. Five patients had an impacted fracture of the femoral neck, and 3 had a fracture of the superior pubic bone. Of 2 patients with advanced arthrosis, i had an impacted femoral neck fracture and the other a nondisplaced ...
Lysozyme, ethylenediaminetetracetic acid, chlorine, x-irradiation and microwaves were used in experimental attempts to eliminate Salmonella senftenberg 775W or Salmonella typhimurium from turkey drumsticks and whole carcasses. Turkey drumsticks or whole carcasses were artificially contaminated with S. senfenberg 775W or S. typhimurium in concentrations ranging between 5 x 10"5 to 8 x 10"5 viable cells per ml. of contaminating fluid. After each treatment, samples were cultured, plated, and tested according to standard methods to determine the susceptibility of Salmonella organisms to the particular treatment. A 0.1 percent solution of lysozyme eliminated the S. senftenberg 775W at 22"0C within three hours. A 0.5 percent solution of ethylenediaminetetracetic acid failed to destroy the test organism under the same conditions. Eighty thousand rads of X-ray eliminated the test organism on turkey drumsticks but failed to remove it from whole turkey carcasses. Microwaves ...
The energetic characteristics of 6 types of poplar clones cultivated for different pedoclimatic conditions in Romania were determined. Four clones were developed in Italy and 2 in Romania. Five experimental cultures were used to analyze the plant survival rate and biomass production rate. After 2 years of study, the Italian clones were found to have very good adaptability to the pedoclimatic conditions in Romania in comparison with local clones. The Italian clones Monviso and AF-6 registered the most substantial growths and the highest resistance to disease. Bioethanol was synthesized by acidic hydrolysis of the cellulose using 2 approaches. In the first approach the lignocellulosic raw material was hydrolyzed with diluted sulfuric acid at 50 degrees C for 24hours. After filtration, the solid residue was treated with 30 per cent H{sub 2}SO{sub 4} at 100 degrees C for 6 hours. The resulting solutions were neutralized with Ca(OH){sub 2} ...
This award provided for an automated computer-controlled goniometer/diffractometer/manipulator with hot and cold stages and data acquisition system that was interfaced with the high resolution Scienta ESCA-300 X-ray photoelectron spectrometer at Lehigh University. The automation allows angular dependent X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) data to be accurately and rapidly collected without the very time-consuming and labor-intensive manual method that was previously required. It also provides for automated multi-sample analyses, collecting both wide survey scans and selected binding energy range analyses, with complete computer control and data storage. This allows 24hour data collection without requiring the continuous presence of operators. The overall result is a greater productivity for the XPS laboratory, approximately doubling the output of the laboratory. While the ...
The activity of tyrosine aminotransferase (TAT) in the liver of mice subjected simultaneously to ionizing radiation and to local inflammatory process showed in the first 24hours of the experiment statistically significant changes resulting from summation of the harmful effects of both factors. In the second 24-hour period an evident tendency was observed for return of a normal circadian rhythm of the enzyme. This points to presence of an endogenous mechanism of suppression of the manifestations of significant desynchronization of the circadian rhythm. The paper contains also a trial of mathematical analysis of changes in TAT activity in the circadian rhythm, a description and analysis or the suppression process, qualitative and quantitative determination of the phenomenon of cumulation of the effects of powerful stress factors acting on the animal organism. The obtained results were compared with the ...
BackgroundSeveral studies have demonstrated the efficacy of artemisinin-combination therapy (ACT) across malaria zones of the world. Fixed dose ACT with shorter courses and fewer...Full Text Available
Recall from visual memory is vulnerable to the influence of task-irrelevant information, including the remembered, prototypical value of stimuli seen previously. Wilken...Full Text Available
An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorption (TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative analysis by On-line mass ...
Full text: In 1995, we demonstrated the use of pretargetting three steps method and biotinylated tetracycline using radiolabelled {sup 99m}Tc-DTPA-biocytinamide for the detection of tumour cells in (C57B1/6 x BALB/C) F1 mice with E-3 thymoma. The three steps were (1) IP injection of biotinylated-tetracycline conjugate (1:1) ratio, (2) 96 hours later Avidin/Streptavidin was injected, and (3) 24hours after (2), {sup 99m}Tc-biocytinamide -cDTPA was injected. Mice were sacrificed 16/24 h after (3) by cervical dislocation. Biodistribution of radioactivity tumour to blood, liver, bone were T:B1= 15.0, T:Li= 5.08, T:Bo=15.0. The percentage of injected dose per g was T= 3.15% and B1= 0.21%. To prolong circulation of Avidin and therefore its uptake into tumour, Avidin was covalently bound to polyethylene-glycol (PEG20 KD) at the molar ratio of PEG:Avidin 100:1 and 400:1. The pegulated Avidin was then cleared from the circulation ...
Purpose : To evaluate whether the early pulmonary irradiation can prevent or decrease the pulmonary damage and contribute to improve ultimate survival in paraquat lung. Materials and Methods : From Jun. 1987 to Aug. 1993, thirty patients with paraquat poisoning were evaluated. Fourteen of these patients were received pulmonary irradiation(RT). All of the patients ere managed with aggressive supportive treatment such as gastric lavage, forced diuresis, antioxidant agents and antifibrosis agents. Ingested amounts of paraquat were estimated into three groups(A: minimal < about 5cc, B: mouthful 5-50 cc, C: Large > 50cc). Pulmonary irradiation was started within 24hours after admission(from day 1 to day 11 after ingestion of paraquat). Both whole lungs were irradiated with AP/PA parallel opposing fields using C0-60 teletherapy machine. A total of 10Gy(2Gy/fr. X 5 days)was delivered without correction of lung ...
...The system recognises the name and confirms it before it starts to dial. To stop the number being dialled say 'cancel'. If ...of the conference : Press the Recall 'R' button and listen for holding dial tone. Select extension or outside number of the person to ...who is going to join the conference Press Recall 'R' to receive dial tone and select '*' and '4'. The call is ...line is faulty and should be reported to the switchboard operators by dialling '0' and giving full details of the fault, the extension ...
Twenty undergraduate students participated in an elaborative learning test to evaluate the relationship between electrical brain activity and subsequently recalled and not-recalled words. Data collected from the midline (Fz, Cz, Pz) and lateral scalp sites (F3, F4, C3, C4, P3, P4) were analysed. The difference between event-related potentials (ERPs) elicited by subsequently recalled and not-recalled words, the ERP memory effect, was evaluated for each portion (primacy, plateau and recency) of the serial-position curve (SPC). We compared peak amplitudes for the P1, N1, P2, N400, P3 and frontal positive slow wave (FPSW) components. The electrophysiological data support the hypothesis that different mechanisms underlie primacy and recency effects during free recall paradigms. There was no support for the hypothesis that an association arises between memory and the FPSW when subjects ...
When the history of neutrons is considered, three large discoveries are recalled, that is, the discovery of neutrons by Chadwick in 1932, the discovery of the nuclear fission of uranium by Hahn and Strassmann in 1938, and the continuation of chain reaction in nuclear fission by Fermi and others in 1942. In neutron capture reaction, the reaction cross section can become very large. The fields of research, to which neutrons have contributed most as the experimental probe, are neutron activation analysis and neutron diffraction. The development of the prompt gamma ray analyzer at the JRR-3M in Japan Atomic Energy Research Institute is reported. This method eliminates the various defects in ordinary neutron activation analysis. By installing the cold neutron source with hydrogen cooling in the JRR-3M, the new field of research was opened. As the combination of a lead-moderated spectrometer and an electron beam type accelerator, the Kyoto University ...
The effects of muscarinic agonists and diisopropylfluorophosphate (DFP) on muscarinic receptor density and muscarinic receptor-mediated responses was assessed in mouse brain and mouse neuroblastoma cells (clone N1E-115). Utilizing the antagonist ({sup 3}H)quinuclidinyl benzilate (({sup 3}H)QNB), there was no difference in the maximal binding capacity (B{sub max}) or equilibrium dissociation constant (K{sub d}) between untreated and 24hour DFP-treated mice. However, one administration of DFP produced a 24% and 33% decrease in B{sub max} measured by ({sup 3}H)N-methylscopolamine (({sup 3}H)NMS) after 18 and 24hours which was rapidly reversible within 36 hours after DFP treatment. The loss of ({sup 3}H)NMS binding sites following acute DFP treatment was not accompanied by a change in a particular muscarinic receptor binding conformation. Furthermore, the magnitude of muscarinic receptor-mediated ...
It is built and tested a transition radiation detector (TRD) to discriminate positrons from protons in the balloon flight TS 93 experiment. It is presented the TRD performance using flight data obtaining a proton-positron rejection factor of the order of 10{sup -3}. During the 24hour flight, the data in the momentum range 4-50 GeV/c are collected. Using the TRD together with the Silicon calorimeter, it is achieved an overall rejection factor of about 10{sup -5} of positron against the proton background over the entire momentum range.
1971 Sorbie et al. described a simple "5"7Co-excretion test (16) as an aid in the diagnosis of iron deficiency anemia. The authors found that renal excretion of a tracer dosis of 0,5 #mu#Ci "5"7CoCl_2 was significantly elevated in patients with iron deficiency anemia (31% of the adminstered dose in 24hours' urine) as compared with the controls (18%). Between 1972-1974 we performed the "5"7Co-excretion test in 29 patients with different kind of anemia and in 10 healthy volunteers. The test was modified by measurement of the serum activity 1, 2, 3, 7, 11 and 24hours after the oral administration of the test dosis. In all anemias as well as in the control group we found the maximum of serum activity three hours after the oral administration of the tracer. The three hours serum activity was elevated in patients with iron deficiency anemia (5.53%/l serum) as compared with the control group (1.92%/l) and ...
Installation of new Shortwave Spectrometer for permanent operation at SGP - In May 2006 the new ShortWave Spectrometer (SWS) was installed in the Optical Trailer at the Southern Great Plains Central Facility SGP on 27 April 2006. The SWS began full operation 28 April 2006 and has run continuously to the present. Over 25 GB of spectra has been collected, calibrated and archived. 3-D radiative transfer simulations - Retrieved fields of cloud optical thickness and effective radius to from the MODIS Airborne Simulator were used to reproduce 3D cloud fields that were used a input to 3D radiative transfer simulations and then compared with simultaneous Solar Spectral Flux Radiometer (SSFR) spectral irradiance measurements. The influence of both horizontal and vertical cloud structure, using accurate versus approximated optical properties in the radiative transfer model on the modeled irradiance was examined, as was the influence of using the full phase function versus using approximations of ...
An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution [1-3] according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorpt(TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the samples from room temperature to 950 C and of quantitative analysis by on-line mass ...
Purpose: To report on the nephron-sparing, percutaneous ablation of a large renal cell carcinoma by combined superselective embolization and percutaneous radiofrequency ablation. Materials and Methods: A 5 cm renal cell carcinoma of a 43-year-old drug abusing male with serologically proven HIV, hepatitis B and C infection, who refused surgery, was superselectively embolized using microspheres (size: 500 - 700 {mu}m) and a platinum coil under local anesthesia. Percutaneous radiofrequency ablation using a 7F LeVeen probe (size of expanded probe tip: 40 mm) and a 200 Watt generator was performed one day after transcatheter embolization under general anesthesia. Results: The combined treatment resulted in complete destruction of the tumor without relevant damage of the surrounding healthy renal tissue. The patient was discharged 24hours after RF ablation. No complications like urinary leaks or fistulas were observed and follow ...
ORDINARY HUMAN REASONING MAY LEAD PATIENTS to provide an unreliable history of past experiences because of errors in comprehension, recall, evaluation and expression. Comprehension of a question may...Full Text Available
'Trojan horses', 'logic bombs', 'armoured viruses' and 'cryptovirology' are terms recalling war gears. In fact, concepts of attack and defence drive the world of computer virology, which looks like a war universe in an information society. This war has several shapes, from invasions of a network by worms, to military and industrial espionage ...
Main features of star evolution are recalled. Then the general structure of white dwarf stars is examined. From the equation of state of an electron gas completely degenerated are deduced: mechanical equilibrium, Viriel theorem, mass-radius relationship and Chandrasekhar limit. These results are applied to neutron stars.
Sears for the Kenmore PRO to schedule a free repair. Consumers can continue to use the cooktop (top burners) and the broiler as well as any clock and/or timer functions. Consumer...
This work deals with a rational vision of stratospheric ozone including the threats on ozone layer, the verifications and the fears. After a recalling on the ozone layer history, the authors treats the question of the ultraviolets particularly the beneficial effects. Then an explanation of the ozone layer decrease is given. (O.L.). 29 refs., 6 figs.
My assignment on the SP-100 Vacuum Vessel Vacuum System Team was to perform a transient pump down analysis for the vacuum vessel that will house the SP-100 reactor during testing. Pump down time was calculated for air and helium. For all cases the proposed vacuum system will be able to pump down the vessel within the required time. The use of a larger rotary piston pump (DUO250) improves the pump down time by 35 minutes and therefore should be considered. The 6-inch duct for the roughing line is optimal, however, because all cases are well below the 24hour time frame, the 4-inch duct is sufficient. The use of the single turbomolecular pump during pump down is sufficient. A pump down with helium in the vessel and a helium inleakage delays the time to achieve the base pressure marginally and is acceptable.
Objective: To find out safety and efficiency of Misoprostol in cervical ripening and induction of labour to achieve vaginal delivery. Results: From Misoprostol insertion to delivery time was 4-24hours. Vaginal delivery was achieved in 80.2%, which included spontaneous, forceps and vacuum extraction. Caesarean section rate was 19.7%. Indications for C. Section included Misoprostol unresponsiveness 11% and fetal distress in 8.6%. Oxytocin augmentation was required in 32% of cases. Term babies were 58%. Intrauterine death and neonatal deaths were 9.8% and 8.6% respectively. Hyper stimulation and postpartum haemorrhage was seen in 2.4% and 3.7% of patients respectively. Conclusion: intravaginal Misoprostol is well tolerated and is very effective for the induction of labour in eclampsia. It helps vaginal delivery in toxemic patients, reduces maternal morbidity, mortality and hospital stay. (author)
Raytheon's Santa Barbara Remote Sensing (SBRS) division designed and built the MTSAT-1R Japanese Advanced Meteorological Imager for the Japanese Ministry of Transport between March, 1999 and July, 2002. In order to meet the stressing requirements of a geosynchronous orbit, a combination of structural, thermal, and optical (STOP) analyses were used to design and optimize the beryllium three-mirror anastigmat (TMA) telescope. This modeling approach was used to characterize and minimize the thermal distortion around local midnight. On-orbit temperatures and structural deformations were predicted using thermal Desktop/SINDA and PATRAN/NASTRAN software, respectively. The resulting optical performance was evaluated using Raytheon developed HEXAGON software. The telescope design was successfully optimized to attain specified visible channel performance for most of the 24hour orbit.
This paper proves that it is practicable to build a new power model which can work efficiently at night by using a type of fluorescence material. The utilization efficiency of photovoltaic cell is improved by prolonging the actual working hours of the cell within 24hours. Both theoretical analysis and experiment on this model are carried out, and base on which the current-time curve (I-t curve) is depicted. It shows that the model which applies the fluorescence material to photovoltaic system is available. According to the analysis and comparison between the attenuating curve of the material and I-t curve of the power system, we can conclude that the weak illumination and the mismatch on wavelength are primary reasons for the low current. Finally, several improved measures of this power model for practical application are given, and it is expected to provide a new thought for photovoltaic study. (orig.)
In the present investigation, the properties of plasma nitrided AISI 304 steel were studied by changing the presence of nitrogen in the gas mixture. The plasma nitriding was performed at temperature -560 deg C, pressure -4 mbar and duration 24hours. The nitrided samples were characterized by evaluating the phase composition, micro hardness, and diffusion layer thickness. The phase analysis indicates the mixed phases of CrN and Fe_3N, Fe_3N and Fe_4N which has the highest intensity. The results show the glow discharge plasma nitriding in presence of N_2 (80 vol. %) and H_2 (rest) produced higher hardness as well as higher case depth. (author)
A characterization study was performed on monosodium titanate (MST) particles to determine the effect of high shear forces expected from the In-Tank Precipitation (ITP) process pumps on the particle size distribution. The particles were characterized using particle size analysis and scanning electron microscopy (SEM). No significant changes in particle size distributions were observed between as-received MST and after 2--4 hours of shearing. Both as-received and sheared MST particles contained a large percentage of porosity with pore sizes on the order of 500 to 2,000 Angstroms. Because of the large percentage of porosity, the overall surface area of the MST is dominated by the internal surfaces. The uranium and plutonium species present in the waste solution will have access to both interior and exterior surfaces. Therefore, uranium and plutonium loading should not be a strong function of MST particle size.
A rare case of primary splenic cyst is shown in a young woman who had a left subcostal abdominal pain. Abdominal echography and CT scan revealed a cyst of the anterior aspect of the spleen. A sorologic test for hidatic disease was negative. On the basis of a presumed diagnostic of nonparasitic cyst, the patient was referred to a laparoscopic decapsulation with excision of the cysts wall not covered by splenic tissue. The patient was discharged 24hours later. Histological report revealed epidermoid cyst. The laparoscopic approach has being recently considered an effective and less invasive alternative in the treatment of splenic diseases. We demonstrated that it should be considered for the treatment of splenic cysts present in a superficial location, with the advantage of organ preservation. (author)
Categorization is complete. Samples 11-3-1 (NSR-F-270409-01) and 11-3-2 (NSR-F-270409-02) are depleted uranium powders of moderate purity (#approx#65-80 % U). The uranium feed stocks for 11-3-1 and 11-3-2 have both experienced a neutron flux (as demonstrated by the presence of "2"3"2U). Sample 11-3-3 is indistinguishable from a natural uranium ore concentrate of moderate purity (#approx#70-80% U). Two anomalous objects (11-3-1-4 and 11-3-2-5) were found in the material during aliquoting. These objects might be valuable for route attribution.
ABSTRACT To date the effect of silver-containing wound dressings on biofilms, known to be present in chronic wounds, has not been determined or documented. In this current study, we aimed to determine the antimicrobial effect of a silver-containing dressing on biofilms grown in a chambered slide model. Before the addition of a wound dressing onto a 24-hour biofilm, composed of either Pseudomonas aeruginosa, Enterobacter cloacae, Staphylococcus aureus, or a mixed bacterial community, a fluorescent dye was applied. This enabled the viability of sessile bacteria to be monitored in real-time, using a rapid form of confocal laser scanning microscopy over a contact time period of 48 hours. By analyzing all the three-dimensional data generated from the confocal time-lapse sequences, 90% of all se...
Natural minerals and some industrial wastes are used as low cost sorbents for removal of metal ions from effluent streams. Apatite as natural mineral and red mud as an industrial waste have been tested for their sorption properties with respect to two important fission products "1"3"7Cs and "9"0Sr. Their ion exchanging capacity was tested after every 4 hours till 24hours. The material gets saturated after 4-8 hours. Hence these materials can be considered for treating in treating LLW before discharge, industrial waste treatment and as backfill or admixture material for shallow land repository. (author)
The mass generation in the Standard Model of Particles Physics relies on a spontaneous symmetry breaking mechanism. Its implementation is recalled, along with its constraints, both theoretical (Naturalness, Stability, Triviality, Unitarity) and experimental (limits of direct and indirect searches, prospects). Calculation techniques for observables evaluation in Perturbative Field Theory are described, particularly Helicity Amplitude method, which is given in details: fermions and vector bosons, massless and massive. Monte-Carlo integration, and structure functions approximations (which allows non-perturbative calculations) are also detailed. With these tools, a process giving to Physics beyond the Standard Model is studied: it leads to an experimental prediction for the LEP collision ring, taking the classical background into account. Technical aspects of a future photon linear collider are reviewed. The production of heavy vector bosons, ...
To examine whether the neuroendocrine hormone norepinephrine may influence the production of the Shiga-like toxins (SLTs), several Escherichia coli O157:H7 clinical isolates were grown in the presence or absence of norepinephrine. An in vitro culture system consisting of low (<1500 colony-forming units/ml) initial concentrations of inocula into a serum-based medium was used to more closely approximate in vivo conditions. The growth of all isolates was increased several logs in the presence of norepinephrine, as compared with the growth in controls, during a 24-hour growth period. Controls included additional dextrose as well as the use of the norepinephrine metabolite normetanephrine, which contains one more methyl group than norepinephrine and hence would serve as a better energy source for growth if the effect were solely nutritionally mediated. During the 24hours of growth, the production of ...
Difficulty in recalling the names of people is very common in the early stages of Alzheimer's disease and in mild cognitive impairment (MCI). However, it is not known whether the difficulty in naming people in MCI reflects problems associated with lexical access or with semantic access. The aims of the present study were to investigate semantic and phonological access to proper names by use of a Tip-of-the-tongue (TOT) task in individuals with multidomain amnestic MCI, individuals with amnestic MCI, and healthy controls, as well as to study the relationships between TOT production and performance in a free recall verbal memory test. In the individuals with multidomain amnestic MCI, the main process affected was phonological access; failures in phonological access were related to deficits i...
The piano repertoire preparation of three undergraduate students at three different academic levels - the first, fifth and eighth semesters - was followed during an academic semester. A phenomenological approach was used to collect data in three stages: an introductory interview, observations of the repertoire under preparation and a final observation of the student's recall about his/her study process. In these steps, four complementary research techniques were employed: a semi-structured interview, observation of video recordings of repertoire performances, an unstructured interview about the repertoire under preparation and a recall-stimulated interview in which the student reflected on audio and video recordings of his/her performance. Data were analysed from an Aristotelian perspectiv...
Finland has some 10 million hectares of peatland, accounting for almost a third of its total area. Macroclimatic conditions have varied in the course of the Holocene growth and development of this peatland, and with them the habitats of the peat-forming plants. Temperatures and moisture conditions have played a significant role in determining the dominant species of mire plants growing there at any particular time, the resulting mire types and the accumulation and deposition of plant remains to form the peat. While in a natural state the mires of Finland have functioned as carbon dioxide sinks throughout the post-glacial period, but the ditching of peatland for forestry and agriculture, amounting to some 5,7 million hectares in Finland, has affected their water balance, especially over the last hundred years, and has thereby altered the quantity and species composition of the mire vegetation. The invasion of trees and woody plants to replace the typical mire plants following ditching ...
In this article, the authors recall the factors apt to influence image quality in NMR Imaging and present the european works that have been developed in MRIQA to set 5 quality assurance tests: EUROSPIN 1 to 5.
Some non-human animals may possess the ability to recall the "what", "where", and "when" of a single past event. We tested the hypothesis that male meadow voles possess the capacity to recall the "what", "where", and "when" of a single past event associated with mate selection in two experiments. Briefly, male voles were allowed to explore an apparatus that contained two chambers. One chamber contained a day-20 pregnant female (24 h prepartum). The other chamber contained a sexually mature female that was neither pregnant nor lactating (REF female). Twenty-four hour after the exposure, the males were placed in the same apparatus, which was empty and clean. At this time, the pregnant female would have entered postpartum estrus (PPE), a period of heightened sexual receptivity. Males initially chose and spent significantly more time investigating the chamber that originally housed the pregnant female (now a PPE female) than the chamber that ...
It is well known that the zeros of orthogonal polynomials interlace. In this paper we study the case of multiple orthogonal polynomials. We recall known results and some recursion relations for multiple orthogonal polynomials. Our main result gives a sufficient condition, based on the coefficients in the recurrence relations, for the interlacing of the zeros of neighboring multiple orthogonal polynomials. We give several examples illustrating our result.
The neocortex plays a critical role in the gradual formation and storage of remote declarative memories. Because the circuitry mechanisms of systems-level consolidation are not well understood, the...Full Text Available
The LS electromagnetic band (1-4 GHz) is widely used both in domestic and industrial domains. Several studies suggested that the biological systems would exhibit a specific sensitivity to the 2.45 GHz microwaves (water resonance frequency). Potential human health hazards and especially a disruption of the cholinergic system have been reported, due to exposure to microwaves even at low power density. This work presents a multi-parametric study of freely moving rat where neuro-physiology was investigated during 70 hours using neurochemical (micro-dialysis technique), electrophysiological, behavioral (vigilance stages quantification) and thermo-physiological approaches. The rats were exposed 24hours to a 2.45 GHz pulsed electromagnetic field at low power density. In this exposure conditions, no significant effect have been reported. (authors)
Development of techniques for separating isomeric nuclides is important to the investigation of schemes for gamma-ray lasers. In preparation for an experiment to separate 10_1_4 atoms of the /sub 197m/Hg (299 keV, tau/sub 1/2/ = 24hours) isomer, we report isotopically selective resonance ionization of mercury atoms. This has been accomplished by three-step excitation via the 6_3P"1 and 8_1S"0 excited states, using three collinear pulsed laser beams of 254, 286, and 532 nm wavelengths from a Nd:YAG and two dye lasers. These beams were passed through a closed mercury-vapor cell containing electrostatic plates to which the ions were drawn. Ion current and fluorescent radiation were measured as a function of laser frequency. Hyperfine structures for the 254- and 286-nm transitions were observed.
This paper reports on pumped storage plants which have become an effective way for some utility companies that derive power from hydroelectric facilities to economically store baseload energy during off-peak hours for use during peak hourly demands. According to the Electric Power Research Institute (EPRI) in Palo Alto, Calif., 36 of these plants provide approximately 20 gigawatts, or about 3 percent of U.S. generating capacity. During peak-demand periods, utilities are often stretched beyond their capacity to provide power and must therefore purchase it from neighboring utilities. Building new baseload power plants, typically nuclear or coal-fired facilities that run 24hours per day seven days a week, is expensive, about $1500 per kilowatt, according to Robert Schainker, program manager for energy storage at the EPRI. Schainker the that building peaking plants at $400 per kilowatt, which run a few hours a day on gas or oil fuel, is less ...
This paper reports on pumped storage plants which have become an effective way for some utility companies that derive power from hydroelectric facilities to economically store baseload energy during off-peak hours for use during peak hourly demands. According to the Electric Power Research Institute (EPRI) in Palo Alto, Calif., 36 of these plants provide approximately 20 gigawatts, or about 3 percent of U.S. generating capacity. During peak-demand periods, utilities are often stretched beyond their capacity to provide power and must therefore purchase it from neighboring utilities. Building new baseload power plants, typically nuclear or coal-fired facilities that run 24hours per day seven days a week, is expensive, about $1500 per kilowatt, according to Robert Schainker, program manager for energy storage at the EPRI. Schainker the that building peaking plants at $400 per kilowatt, which run a few hours a day on gas or oil fuel, is less ...
Platelet deposition on bovine pericardial-tissue mitral-valve prostheses in 11 dogs was observed noninvasively by use of "1"1"1In-labeled platelets and quantified after sacrifice at one (n . 3), 14 (n . 3), and 30 (n . 5) days postimplantation (300-400 microCi of labeled platelets having been injected 24hours previously). Thrombosis on the sewing ring and pericardial leaflets at one and 14 days and on the leaflets at 30 days was delineated in scintiphotos. In vitro quantification (% injected dose) indicated that the leaflets, sewing ring, and perivalvular tissue retained 0.904% of labeled platelets at one day postimplantation, 0.198% at 14 days, and 0.040% at 30 days. Platelet half-life was reduced to 38 hours at 21 days postimplantation but returned toward the normal (50 hours) with fibrous ingrowth in the sewing ring. Microembolism in lung and kidney, as measured by tissue/blood radioactivity ratio, also was decreased significantly at 30 ...
A new hydroxyiminoamide ligand, 1-(2-nitroimidazole-1-yl)-propanhydroxyiminoamide (N2IPA) was synthesized. The biodistribution of {sup 99m}Tc-N2IPA in mice bearing S180 tumor demonstrated that the complex showed a selective accumulation in tumor and slow clearance from it. The tumor-to-tissue uptake ratios increased with time. At 4 hours after injection, the uptake ratios of tumor to muscle, blood, liver, heart, and lung reached 8.4, 1.5, 0.6, 2.9, and 2.3, respectively. Moreover, the tumor-to-liver uptake ratio steadily increased to 0.9 at 8 hours and 2.3 at 24hours. The complex showed little uptake and quick clearance in blood, lung and other organs. Compared with other proposed hypoxia-imaging agents, this novel agent has advantages of higher tumor-to-muscle and tumor-to-blood uptake ratios and easier synthesis.
In the present study a partial replacement of aggregate with two different ratios of waste rubber (5%, 10%) with the addition of a constant ratio of rice husk ash (RHA), 5% was carried out. The hardened cement mortar used the optimum water of consistency. The specimens were molded into 1 inch cubic moulds .The specimens were first cured for 24hours, at 100% relative humidity and then cured under tap water for 3, 7 and 28 days followed by irradiation at different doses of gamma irradiation namely 5 and 10 kGy. The physico-chemical and mechanical properties such as compressive strength, total porosity and bulk density were studied for the three types of specimens. The results showed that the values of the compressive strength, bulk density and chemically combined water of the blended cement mortar paste (OPC-RHA) increase ,while blended cement mortar paste with 5% RHA and 5, 10% waste rubber decrease. The results were confirmed by scanning ...
Peeled Avena sativa coleoptile sections have been used to study the control of solute uptake under conditions where the uptake is not limited by the cuticular barrier. In the presence of 2% sucrose, auxin enhances the rate at which the total osmotic solutes increase, but this appears to be a response to the increased growth rate, inasmuch as the auxin effect is eliminated when growth is inhibited osmotically. When sections are incubated in sucrose or in 10 millimolar NaCl, the osmotic concentration increases until a plateau is reached after 8 to 24hours. Auxin has no effect on the initial rate of increase in osmotic concentration. This difference in steady-state osmotic concentration is, in part, a response to auxin itself, as it persists when auxin-induced growth is inhibited osmotically. The upper limit for osmotic concentration does not appear to be determined by the turgor pressure, inasmuch as a combination of sucrose and NaCl gave a ...
Iofetamine HCI {sup 123}I is the generic name for the hydrochloride salt of N-isopropyl-p-iodoamphetamine labeled with {sup 123}I, commonly called IMP. Iofetamine HCI {sup 123}I is prepared by isotopic exchange with [{sup 123}I]Nal and is formulated in isotonic aqueous NaCl solution containing 1 mCi/ml iofetamine HCI I 123, 0.15 mg/ml iofetamine HCI carrier, and phosphate buffer for pH control. The radiochemical purity is >97%, and the product is stable for more than 24hours; the commercial product distributed today is prepared with high purity {sup 123}I with >98% radionuclidic purity. Two radioiodinated agents have seen significant clinical application for functional brain imaging: iofetamine HCI (IMP) (1) and N,N,N{prime}-trimethyl-N{prime}-(2-hydroxy-3-methyl-5-iodobenzyl)-1,3-propanediamine HIPDM (2). lofetamine HCI {sup 123}I is commercially available in the United States, Europe, and Japan. Although their primary use is for ...
adult males and females, less than 24hours old, of the spiny bollworm, Earias Insulana boisd. were irradiated with sub sterilizing doses of 50,80,100 and 150 gray (Gy). treated moths were out crossed with normal adults and observed for their ability to reproduce. inherited deleterious effects resulting from irradiation of p_1 moths were recorded for several generations. the reduction in both fecundity and egg viability increased by increasing the dose applied to p_1 adult moths .at all tested doses, the females were more radiosensitive than males, as for reduction in fecundity and egg viability. the progeny from irradiated parental females are not as sterile as the progeny from irradiated parental males. the reduction of egg hatching continued in the progeny of irradiated males through F_1 and to lesser extent through F_2 .on the other hand , irradiation of P_1 females reduced the rate of egg hatching among parental generation and to lesser ...
Dynamic fracture toughness tests were performed on materials which had been subjected to one of three long-time post weld type stress relief heat treatments: 48 hours at 1000/degree/F (538/degree/C), 24hours at 1125/degree/F (607/degree/C), and 48 hours at 1125/degree/F (607/degree/C). Linear elastic K/sub Id/ results were obtained at low temperatures while J-integral techniques were utilized to evaluate dynamic fracture toughness over the transition and upper shelf temperature ranges. Tensile, Charpy impact, and drop weight nil-ductility transition tests as well as room temperature, air environment fatigue crack growth rate tests (SA508 Cl 2a only) were also performed. The fracture toughness of both materials exceeded the ASME specified minimum reference toughness K/sub IR/ curve. 17 refs.
Dynamic fracture toughness tests were performed on materials which had been subjected to one of three long-time post weld type stress relief heat treatments: 48 hours at 1000/degree/F (538/degree/C), 24hours at 1125/degree/F (607/degree/C), and 48 hours at 1125/degree/F (607/degree/C). Linear elastic K/sub Id/ results were obtained at low temperatures while J-integral techniques were utilized to evaluate dynamic fracture toughness over the transition and upper shelf temperature ranges. Tensile, Charpy impact, and drop weight nil-ductility transition tests as well as room temperature, air environment fatigue crack growth rate tests (SA508 Cl 2a only) were also performed. The fracture toughness of both materials exceeded the ASME specified minimum reference toughness K/sub IR/ curve. 17 refs.
A 1,200 bird solar chicken brooder was indigenously designed and operated by the Indian scientists for the first time in the country as a Project under funding by the Ministry of Non Conventional Energy Sources to the All India Women`s Conference. This multi disciplinary project was taken up on the International Sun Day, May 3, 1993 and completed on May, 1994. Data has been collected for the first nine months of operation. Its successful operation has justified multi disciplinary approach. The solar chicken brooder incorporates modern poultry concepts of breeding under controlled temperatures. In view of the mixed climate of Delhi, provision was made for heating and cooling both to take care of the 24hour cycle. Comfort conditions have been identified and maintained (as is done in the their genetic characteristics) at different temperatures for a period of 8--10 weeks to grow them to a uniform weight of 2.0 kg. Growing them under controlled ...
North Dakota Concrete Products Company uses a steam curing process that accelerates the concrete curing so that 28-day strength is obtained within 24hours. The cost of energy required to accomplish this is significant, amounting to approximately $80,000 in 1980. The present boilers are oil fired. Recently, fuel oil prices have increased substantially. Further, supply shortages in the past have threatened plant production. The purpose of this study was to evaluate the economic feasibility of using deep formation warm water as an alternative energy source. A water-to-water heat pump system to replace the existing boiler system was investigated. TPI, Inc. economic and engineering findings for this particular potential geothermal application are disclosed. The operating cost savings of the geothermal system over the operating costs of the existing oilfired system would be insufficient to provide an acceptable rate of return on the investment at ...
Thirty-six patients with acquired immunodeficiency syndrome (AIDS), who were febrile but without localizing signs, underwent indium-111 leukocyte scintigraphy 24hours after injection of labeled white blood cells (WBCs) and were restudied 48 hours after injection of gallium-67 citrate. Fifty-six abnormalities were identified as possible sources of the fever; 27 were confirmed with biopsy. Of these 27, 15 were identified only on In-111 WBC scans (including colitis, sinusitis, and focal bacterial pneumonia); six, only on Ga-67 scans (predominantly Pneumocystis carinii pneumonia and lymphadenopathy); and six, on both studies (predominantly pulmonary lesions). In-111 WBC scanning revealed 21 of 27 abnormalities (78%) and gallium scanning, 12 of 27 (44%). If only one scintigraphic study has been performed, particularly with Ga-67, a significant number of lesions would not have been detected. The authors believe radionuclide evaluation of the febrile ...
Citrate is an important naturally occurring inhibitor of calcium stone formation in urine. Urinary citrate excretion was examined in 43 consecutive patients with recurrent idiopathic calcium nephrolithiasis and in 50 normal controls by a specific enzymatic technique. Hypocitraturia (<1.6 mmol/24h) was found in 14 (33%) stone formers compared to 6 (12%) normal controls (p = 0.03). Citrate excretion expressed as citrate-creatinine ratio in 24hour urine samples was significantly lower in the stone formers than in the healthy controls (p = 0.03), and significantly lower in healthy men, compared to healthy females (p = 0.006). There was a great variability in urinary citrate levels in both groups, and a considerable overlap in the urinary citrate excretion between normal subjects and stone formers. Factors other than urinary citrate excretion must therefore be of importance in the pathophysiology of calcium stone formation. Citrate-calcium ratio ...
We studied the dose-response effects of #gamma#-irradiation on the weight gains of the body and the brain in ICR mice exposed to various doses of "6"0Co #gamma#-irradiation ranging from 0 to 1.5 Gy on day 13 of pregnancy (E13). We found that 0.5 Gy #gamma#-irradiation caused a significant reduction in brain weight but not in body weight among 6-week-old mice. Higher doses (1.0, 1.5 Gy) seriously inhibited body and brain development, resulting in significantly low weights at 6 weeks of age. A significantly lower brain weight among fetuses exposed to 1.5 Gy was found as early as 24hours after exposure, while significant reductions in the body weight of these same fetuses appeared 3 days after exposure. The effects of radiation on brain and body development were similar for both males and females. (author).
Quantitative bone scintigraphy was performed at 4 and 24 h after injection of {sup 99m}Tc-MDP. The lower thoracic and all the lumbar vertebrae were recorded in 37 patients with prostatic carcinoma before orchiectomy as well as two weeks, two and six months postoperatively. Fourteen patients had normal bone scintigrams. By means of the measured variation in the count rate between normal vertebrae, the criterion for a vertebra to be considered as abnormal was determined using the 4 h-uptake values. For patients with normal scintigrams the count rate at 24 h was below the 4 h level and the mean 24 h/4 h ratio was determined to be 0.85 {+-} 0.09 (1 SD). Normal vertebrae in patients with skeletal metastases had only slightly lower count rate values at 24 h than at 4 h. Abnormal vertebrae showed a higher count rate at 24 h, especially two weeks postoperatively, while a tendency towards lower values than at 4 h was seen after 6 months. If the 24 h/4 h ratio is used as an extra criterion to ...
Quantitative bone scintigraphy was performed at 4 and 24 h after injection of "9"9"mTc-MDP. The lower thoracic and all the lumbar vertebrae were recorded in 37 patients with prostatic carcinoma before orchiectomy as well as two weeks, two and six months postoperatively. Fourteen patients had normal bone scintigrams. By means of the measured variation in the count rate between normal vertebrae, the criterion for a vertebra to be considered as abnormal was determined using the 4 h-uptake values. For patients with normal scintigrams the count rate at 24 h was below the 4 h level and the mean 24 h/4 h ratio was determined to be 0.85 #+-# 0.09 (1 SD). Normal vertebrae in patients with skeletal metastases had only slightly lower count rate values at 24 h than at 4 h. Abnormal vertebrae showed a higher count rate at 24 h, especially two weeks postoperatively, while a tendency towards lower values than at 4 h was seen after 6 months. If the 24 h/4 h ratio is used as an extra criterion to the ...
Investigations of sucrose synthase in maize root tips have required development of a means to circumvent the rapid decline of activity observed after extraction dialysis and either synthetic or degradative assays. Several protease inhibitors were tested; although PMSF increased initial activity, no inhibitor prevented the drop in activity with time. Western blot analysis indicated that activity decline was not associated with protein degradation. Therefore, a procedure was developed which (1) shortened extraction-to-assay period from ca. 24hours to 7 minutes, (2) simplified previous assays and (3) reduced the amount of tissue required. Extract was desalted with spun columns and the {sup 14}C-UDPG product recovered with DEAE ion exchange paper. The minute quantities of product recovered can be concealed by the presence of trace impurities in the {sup 14}C-sucrose utilized. DEAE ion exchange paper was used to remove interfering radio-labelled ...
The regional concentrations of nine radiochemicals were measured in rat brain after induction of cerebral ischemia to identify tracers concentrated by brain undergoing selective neuronal necrosis. Transient (30 minute) forebrain ischemia was produced in the rat; 24hours after cerebral recirculation the radiochemicals were injected intravenously and allowed to circulate for 5 hours. The brain concentrations of the radiochemicals in dissected regions were determined by scintillation counting. Forebrain ischemia of this nature will produce extensive injury to striatal neurons but will spare the great majority of neocortical neurons at 24hours. The regional concentrations of these radiochemicals varied considerably in both control and ischemic animals. In postischemic animals, 4 radionuclides (/sup 63/Ni, /sup 99/TcO/sub 4/, /sup 22/Na, and (/sup 3/H)tetracycline) were concentrated in the irreversibly ...
Solid fuels such as coal, wood, and crop straw supply some fraction of household cooking and heating fuel for more than one billion people in China. As these fuels do not generally combust cleanly in household stoves, their use levies large health and environmental burdens, particularly in rural regions. Production of clean-burning fuels from agricultural residue offers one prospect for mitigating health and social burdens imposed by household use of solid fuels. This dissertation explores the question: how might production of clean-burning household fuels from agricultural residues affect human health and social conditions in rural China? I approach this question from three perspectives. First, a technically plausible but currently unproven village-scale energy technology is explored in a scenario bounded by natural resources and substantiated by engineering specifications, estimates of indoor exposures to air pollution, and epidemiological analyses. This analysis asks at the national ...
The Large Hadron Collider (LHC) project, approved by the CERN Council in December 1994, has now fully entered its construction phase, with the detailed technical definition of the major systems, and the adjudication of a number of large procurement contracts. We first recall the main features and characteristics of the LHC, report on the advances in definition of the layout and optics as well as on preparation of the injector complex, and review recent progress in the key technical systems of the main ring: magnets, cryogenics and vacuum, as well as civil construction, which has started following acceptance by authorities in the Host States.
The paper demonstrates an application of advanced decision support tools within the framework of the environmental information system of the Province of Milan. These tools include environmental simulation models, multi criteria analysis, risk analysis and environmental accounting for marketable emission permits. After describing the general structure of the system, three demonstrational case studies are introduced concerning: groundwater pollution management; atmospheric pollution management; urban environmental quality perception and management. In the conclusion, potential use of tools like the ones implemented by the province of Milan within the framework of Local Agenda 21 processes is recalled.
Several types of X-band high power loads developed for several tens of MW range were designed, fabricated and used for high power tests at X-band facility of KEK. Some of them have been used for many years and few units showed possible deterioration of RF performance. Recently revised-design loads were made by CERN and the high power evaluation was performed at KEK. In this paper, the main requirements are recalled, together with the design features. The high power test results are analysed and presented
This work gives a global view of legislations in which are included metals chemical states, briefly recalls the conditions to be respected for the CRM (Certified Reference Materials), and describes the results of some current plans for the Norms, Measures and Tests program. (O.M.) 23 refs.
Acute thoracic aortic injuries account for up to 10-20% of fatalities in high-speed deceleration road accidents and have an estimated immediate fatality rate of 80-90%. Untreated survivors to acute trauma (10-20%) have a dismal prognosis: 30% of them die within 6 hours, 40-50% die within 24hours, and 90% within 4 months. It was investigated the diagnostic accuracy of Helical Computed Tomography (Helical CT) in acute traumatic injuries of the thoracic aorta, and the role of this technique in the diagnostic management of trauma patients with a strong suspicion of aortic rupture. It was compared retrospectively the chest Helical CT findings of 256 trauma patients examined June 1995 through August 1999. Chest Helical CT examinations were performed according to trauma score, to associated traumatic lesions and to plain chest radiographic findings. All the examinations were performed with no intravenous contrast agent administration and the pitch 2 ...
The translocation of particles from the alveolar compartment to the pleural space and tracheobronchial lymph nodes was investigated in rats over a 30 day period following the intrapulmonary instillation of 4 x 10/sup 8/ polystyrene microspheres (1.9 ..mu..m dia.). In initial studies, approx. =10/sup 4/ particles were found in the pleural space compartment on Days 1, 14 and 30 after particle deposition, and most of these were cell-associated. Subsequent pleural space studies indicated, however, that the particles found in this compartment were, at least in part, due to the pleural lavage technique, and, unlike observations reported for some fibers, the translocation of the particles used in our study to the pleural space does not represent an important lung clearance pathway. In regard to particle clearance to the tracheobronchial lymph nodes, the accumulation of particles, most of which were extracellular, kinetically was biphasic with the most rapid phase occurring within the first ...
The effect of in vitro and in vivo administration of ethanol on the binding of "3"5S-t-butyl-bicyclophosphorothionate ("3"5S-TBPS) to cortical brain membranes of C57B1 mice was investigated using KCl (100 mM) containing assay media. The in vitro addition of ethanol produced a dose-dependent inhibition of basal "3"5S-TBPS binding. In the presence of chloride ions, GABA and pentobarbital had a biphasic action (stimulation followed by inhibition) on "3"5S-TBPS binding, whereas diazepam only stimulated the binding. Ethanol reduced the stimulatory effects of GABA and pentobarbital in a dose-dependent manner, but had no effect on the enhancement of "3"5S-TBPS binding produced by diazepam. "3"5S-TBPS binding to cortical brain membranes was inhibited by the putative Cl"- channel blocking agent DIDS. This inhibitory action of DIDS was significantly, and dose-dependently reduced by ethanol (#<=# 100 mM ethanol). Chronic ethanol ingestion in vivo, which produced tolerance to and physical ...
To assess the efficacy and resulting complications of tetracycline sclerotherapy in renal, hepatic, ovarian, and perivesical cysts. We retrospectively reviewed 23 cases of benign cysts (16 renal, 4 hepatic, 2 ovarian, and 1 perivesical) in 22 patients in whom the condition was diagnosed or confirmed by either ultrasound, CT, or cytology, and who underwent percutaneous tetracycline sclerotherapy. Using a 21-gauge Chiba needle, the target cyst was punctured under ultrasound guidance. Prior to the injection of 1500 mg of tetracycline diluted in 5 ml of normal saline, almost all the cystic content was aspirated, and at the end of the procedure the tetracycline was left in the cyst. During a period of between 3 and 22 months, 18 of the 23 cases were followed up. In six of the 18 cases followed up, the cysts either decreased in size by 10%, or collapsed completely. In seven cases a collapse of over 50% was noted, and in the remaining five the cyst recurred. In one of these, complete collapse ...
Airbag pressure vessels for the north-American market mainly are made by forging and by the use of steel alloys. In Europe aluminum alloys are common and the manufacturing process is extrusion of circular blanks - made from cold rolled plates - in a form applying a 100 t press at room temperature. Then by heat treatment the strength/hardness of the material is properly adjusted and after that the pressure vessel parts have to be continuously inspected with an inspection and handling cycle time of 3 s. Inspection of the axis-symmetric parts is asked for surface breaking extrusion defects as well as for surface parallel delaminations in the bulk volume. Furthermore, the material strength is a quality characteristic that has to be nondestructively registered and documented. The inspection is performed by eddy current probes and an EMAT, of which the eddy current impedance measurements are used for surface breaking extrusion defect detection and sizing (single frequency technique with ...
Activation dose rates have been computed for the Poloidal Divertor Experiment Tokamak at the Princeton Plasma Physics Laboratory. Dose rates were computed in one-dimensional (cylindrical) geometry using the ANISN S/sub n/ transport theory code and the DKR radioactivity code. The EPR (DLC37F) 121-group coupled neutron-gamma cross section library was used with ANISN. For DKR, the 46-group neutron library of DCDLIB was employed. Dose rates were calculated for 1 minute, 1 hour, 6 hours, 24hours, 1 week, and 1 month following a single pulse yielding 10/sup 15/ neutrons and for 2 hypothetical pulsing sequences. First, it was assumed that 10 pulses were conducted each day (1 hour apart) for 5 days. Second, it was assumed that 100 pulses were conducted each day (6 minutes apart) for 5 days. It was found that /sup 56/Mn and /sup 64/Cu are the main contributors to the dose at short time periods after shutdown, while, for long time periods, /sup 58/Co ...
A recent road test at LLNL underscored the zinc/air battery`s capacity to give electric vehicles some of the attractive features of gas-driven cars: a 400-km range between refueling, 10-minute refueling, and highway-safe acceleration. Developed at Lawrence Livermore National Laboratory, the battery weights only one-sixth as much as standard lead/acid batteries and occupies one-third the space, yet costs less per mile to operate. What`s more, because the battery is easily refuelable, it promises trouble-free, nearly 24-hour-a-day operation for numerous kinds of electric vehicles, from forklifts to delivery vans and possibly, one day, personal automobiles. The test of a Santa Barbara Municipal Transit bus with a hybrid of zinc/air and lead/acid batteries capped a short development period for the zinc/air battery. The test run indicated the zinc/air battery`s potential savings in vehicle weight from 5.7 to 4.0 metric tons, in battery weight from ...
Pulsatile hormone secretion is observed in almost every hormonal system. The frequency of episodic hormone release ranges from approximately 10 to 100 pulses in 24hours. This temporal mode of secretion is an important feature of intercellular information transfer in addition to a dose-response dependent regulation. It has been demonstrated in a number of experiments that changes in the temporal pattern of pulsatile hormone secretion specifically regulate cellular and organ function and structure. Recent evidence links osteoporosis, a disease characterized by loss of bone mass and structure, to changes in the dynamics of pulsatile parathyroid hormone (PTH) secretion. In our study we applied nonlinear and linear time series prediction to characterize the secretory dynamics of PTH in both healthy human subjects and patients with osteoporosis. Osteoporotic patients appear to lack periods of high predictability found in normal humans. In contrast ...
The development of the microstructure on aging of an (#alpha# + #beta#) type titanium alloy containing 6Al-1.6Zr-3.3Mo-0.3Si (VT9) (in weight percent) has been studied. The #beta#-transus temperature of this alloy is approximately 1243 K. Solution treatment in the #beta#-phase field of the alloy followed by quenching in water at room temperature resulted in the formation of a single-phase martensite structure. The martensitic structure was confirmed to be orthorhombic (#alpha# double-prime) using X-ray diffraction. The water-quenched (WQ) specimens were subjected to aging treatments at temperatures of 823, 873, and 973 K for various lengths of time. Aging at 823 K for times between 24 and 100 hours did not bring about any noticeable change in the microstructure. Aging at 823 K for 200 and 300 hours resulted in the heterogeneous precipitation of s_2 silicide particles and thin films of #beta# sandwiched between the interplatelet boundaries of martensite. Electron diffraction analysis ...
Sixty-Hz magnetic field exposures were measured for 45 adult residents of Maine. Thirty of the subjects resided near rights-of-way (ROWs) with either 345- and 115-kV transmission lines, or ROWs with only 115-kV transmission lines; fifteen resided far from any transmission lines. Personal exposure data for a single 24-hour period was acquired with the EMDEX. The EMDEX's event-marker button was used to partition exposures into Home and Away components. Also, three area measurements were taken for each subject during the personal exposure measurement period: (1) 24-hr fixed-site bedroom measurement with a second EMDEX; (2) Spot measurements in at least three rooms of every residence; and (3) Spot measurements outside each residence. Residence near transmission lines highly loaded during the measurement period was associated with increased Home and Total exposure relative to a far-away population. Average exposure level while away from ...
We studied the interaction of Pu(VI) with Pseudomonas stutzeri ATCC 17588 and Bacillus sphaericus ATCC 14577, representatives of the main aerobic groups of soil bacteria present in the upper soil layers. The accumulation studies have shown that these soil bacteria accumulate high amounts of Pu(VI). The sorption efficiency toward Pu(VI) decreased with increasing biomass concentration due to increased agglomeration of the bacteria resulting in a decreased total surface area and number of available complexing groups. Spores of Bacillus sphaericus showed a higher biosorption than the vegetative cells at low biomass concentration which decreased significantly with increasing biomass concentration. At higher biomass concentrations (> 0.7 g/L), the vegetative cells of both strains and the spores of B. sphaericus showed comparable sorption efficiencies. Investigations on the pH dependency of the biosorption and extraction studies with 0.01 M EDTA solution have shown that the biosorption ...
One rationale proposals to increase the efficiency of PDT is to combine photo-sensitization with other treatment modalities, including modulation of arachidonic acid metabolism. In combine treatment we examined the effects of 48 h and 24 h pre-treatment of cells with 5- lipoxygenase inhibitor MK-886 prior to photoactivation of hypericin on cell cycle distribution and DNA synthesis. All parameters were examined 24hours after hypericin activation. Pre-treatment of HT-29 with 5-lipoxygenase inhibitor MK-886 followed by PDT resulted in most significant effects on cell cycle perturbations. Administration of MK-886 alone as well as combination of low doses MK-886 with hypericin induced S phase accumulation. Increasing of MK-886 concentration induced massive changes in the cell cycle progression. Pre-treatment of HT-29 cells with MK-886 alone (15 #mu#M; - 48 h) caused accumulation of cells in S-phase (58 % in S-phase and 36 % in G_0/G_1 phase). ...
Incorporation of tritium into body constituent molecules from tritiated water and its in vivo behaviors were studies using rats. In single administration of HTO, "3H behaviors were studied in lipids that are rich in hydrogen. Incorporation of "3H into the lipid fraction from HTO and its release differed by each organ and by the type of lipid components. Of routes of administration, the oral and parenteral routes showed same results, and no prominent difference was noted by inhalation. By consecutive administration, the urine "3H concentration showed no difference according to the route, but increased as the concentration of administered HTO increased. When administration was discontinued after the urine "3H concentration reached a plateau, the biological half-life was about 4.5 days, almost in agreement with the value by single administration. In relation to water intake, increase in the urine volume and accompanying promotion of urine "3H excretion in approximate proportion to water ...
Patients with Ewing's sarcoma who present with a central axis or proximal extremity primary and/or with metastatic disease have a poor prognosis despite aggressive combination chemotherapy and local irradiation. In this high risk group of patients, total body irradiation (TBI) has been proposed as a systemic adjuvant. To aid in the design of a clinical TBI protocol, the authors have studied in the in vitro radiation response of two established cell lines of Ewing's sarcoma and human bone marrow CFUc. The Ewing's lines showed a larger D_0 and anti-n compared to the bone marrow CFU. No repair of potentially lethal radiation damage (PLDR) was found after 4.5 Gy in plateau phase Ewing's sarcoma cells. A theoretical split dose survival curve for both the Ewing's sarcoma lines and human bone marrow CFUc using this TBI schedule shows a significantly lower surviving fraction (10"-"4-10"-"5) for the bone marrow CFUc. Based on these in vitro results, two 4.0 Gy fractions separated by ...
Because of heightened media coverage, a 24-hour news cycle and the potential miscommunication of health messages across all levels of government during the onset of the H1N1 influenza outbreak in spring 2009, the Illinois Department of Public Health (IDPH) decided to evaluate its H1N1 influenza A communications system. IDPH wanted to confirm its disease information and instructions were helping stakeholders prepare for and respond to a novel influenza outbreak. In addition, the time commitment involved in preparing, issuing, monitoring, updating, and responding to H1N1 federal guidelines/updates and media stories became a heavy burden for IDPH staff. The process and results of the H1N1 messaging survey represent a best practice that other health departments and emergency management agencies can replicate to improve coordination efforts with stakeholder groups during both emergency preparedness and response phases. Importantly, the H1N1 survey ...
The effects of felbamate on the pharmacokinetics of a low-dose combination oral contraceptive containing 30 micrograms ethinyl estradiol and 75 micrograms gestodene were assessed in a randomized, double-blind, placebo-controlled parallel-group study in healthy premenopausal female volunteers established in a regimen of oral contraceptive use. They received either placebo or 2400 mg/day felbamate from midcycle (day 15) to midcycle (day 14) of two consecutive oral contraceptive cycles (months 1 and 2). Pharmacokinetic assessments of ethinyl estradiol and gestodene were performed on day 14 of both cycles. To determine whether ovulation occurred, plasma progesterone and urinary luteinizing hormone levels were measured, and diaries recording vaginal bleeding were kept. Felbamate treatment resulted in a significant 42% decrease in gestodene area under the plasma concentration-time curve (0 to 24hours) (p = 0.018) compared with baseline, whereas a ...
To determine the effects of ammonium chloride (NH4Cl) dosage and swimming exercise training during 4 weeks on bone metabolic turnover in rats, seven-week-old female 24 Wister-Kyoto (WKY) rats were investigated by bone status including bone mineral density (BMD) and biomechanical markers from blood and urine. Twenty-four rats (initial weight: 191.2+/-7.6 g) were randomly divided into four groups: baseline (8 weeks old) control group (n=6, BC), 4-week control group (n=6, Con), 4-week swimming exercise loading group (n=6, Swim) and 4-week chronic NH4Cl dosage group (n=6, Acid). All rats were fed an AIN93M diet (Ca: 0.5%, P: 0.3%), and both Con and Swim groups were pair-fed by feeding volume of the NH4Cl dosage group. The acid group only received 0.25 M NH4Cl distilled water ad libitum. At the end of the experimental period, rats were sacrificed with blood drawn and femur and tibia were removed for analysis of bone mineral density (BMD) by dual energy X-ray absorptiometry (DEXA). In the ...
The data center in this study had a total floor area of 8,580 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 440 racks, and was located in a 208,240 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but served by the main building chiller plant and make-up air system. Additionally, it was served by a single electrical supply with no provision for backup power. The data center operated on a 24hour per day, year-round cycle, and users had all hour full access to the data center facility. The study found that data center computer load accounted for 23% of the overall building electrical load, while the total power consumption attributable to the data center including allocated cooling load and lighting was 30% of the ...
A precise admixtures system is needed when using high-volume fly ash concrete as fresh concrete occasionally undergoes rapid slump loss after mixing, which can cause problems with casting, pumping and finishing of the concrete in hot weather. This paper provided details of a study conducted to implement high-volume fly ash concrete technology in India. Different families of admixtures were investigated to determine their water reduction capacities. A set-retarding admixture was used in some of the concrete mixtures in order to determine its efficacy. An Indian Portland cement was used to create a total of 22 different concrete mixtures. Four different fly ashes were used to replace portions of the concrete. The slump of the fresh concrete mixture was monitored for 2 to 3 hours. Unit weight and temperature of the concrete was measured. Specimens were cast in steel moulds in order to determine the compressive strength and unit weight of the hardened concrete. The concretes were demoulded ...
The three main objectives of this study were: (1) to determine if depletion of proteoglycans from the cartilage matrix that occurs during osteoarthritis causes a measurable increase of cartilage proteoglycan components in the synovial fluid and sera, (2) to observe what effect intracellular cAMP has on the expression of matrix components by chondrocytes, and (3) to determine if freshly isolated chondrocytes contain detectable levels of mRNA for fibronectin. Canine serum keratan sulfate and hyaluronate were measured to determine if there was an elevation of these serum glycosaminoglycans in a canine model of osteoarthritis. A single intra-articular injection of chymopapain into a shoulder joint increased serum keratan sulfate 10 fold and hyaluronate less than 2 fold in 24hours. Keratan sulfate concentrations in synovial fluids of dogs about one year old were unrelated to the presence of spontaneous cartilage degeneration in the joints. High ...
This paper presents results of a laboratory and field study of naphthenic acid corrosion and the development of an effective chemical inhibitor for this type of corrosive attack. In the laboratory corrosion test, which involved 20 hour weight loss measurements in high flash solvent with a total acid number (TAN) of 16 mg KOH/gm at a temperature of 600 F (316 C), blank corrosion rates averaged 140 to 150 mpy (3.56 to 3.81 mm/y). Inhibited rates averaged about 10 to 12 mpy (0.254 to 0.305 mm/y). The field test was carried out on a heavy vacuum gas oil (HVGO) stream at 550 F (288 C) . Blanks varied from a high of 425 mpy (10.79 mm/y) for a 24hour test to a low of about 100 mpy (2.54 mm/y) for a 150 hour test. Both electrical resistance (ER) probes and weight loss coupons showed corrosion rates below 5 mpy (0.127 mm/y) as long as they were adequately passivated. Passivation consisted of exposing the coupons to a high inhibitor dosage for a ...
Sleep after learning is often beneficial for memory. Reinstating an environmental context that was present at learning during subsequent retrieval also leads to superior declarative memory performance. This study examined how post-learning sleep, relative to wakefulness, impacts upon context-dependent memory effects. Thirty-two participants encoded word lists in each of two rooms (contexts), which were different in terms of size, odour and background music. Immediately after learning and following a night of sleep or a day of wakefulness, memory for all previously studied words was tested using a category-cued recall task in room one or two alone. Accordingly, a comparison could be made between words retrieved in an environmental context which was the same as, or different to, that of the ...
Two quantities play a central role in that part of nonlinear optics which deals with the effects of a finite momentum spread in a particle beam: the orbit position whose derivative with respect to momentum is called 'orbit dispersion' and the betatron wave number whose derivative WRT momentum is the 'chromaticity'. The orbit dispersion varies with the azimuth and is essentially horizontal in a machine with a horizontal symmetry plane; parasitic radial fields induce a vertical component. The chromaticity is a scalar quantity related to the integral of the focusing strength, over one turn of the machine; it is defined for the horizontal and vertical planes. After recalling the general motion equation in the horizontal plane, the orbit dispersion and the chromaticity will be treated. Closed formulae are given for lumped elements and special emphasis is put on dipoles with a high deflection angle. (8 refs).
Cellular telephones emit a radiofrequency electromagnetic field, part of which is absorbed in the user's head. Many studies have been conducted to look for their possible health hazard to human, at the experimental, epidemiological or clinical level. After a short recall on dosimetry, the author describes the state-of-the art about harmful and irreversible effects, up to now not confirmed, and about some benign symptoms which look absolutely actual. A causal relationship of the electromagnetic field on these benign symptoms is however not proven; other, studies are running to evaluate their possible long-term consequences. Interferences with cardiac pacemakers can easily be avoided by holding the telephone handset farther than 10 cm. (author)
The present study consisted of two experiments to compare new word learning in healthy young (N = 11) and older (N = 17) adults within an explicit learning paradigm. Experiment 1 investigated the new name learning for familiar objects, while Experiment 2 investigated learning names and descriptions for unfamiliar objects. Participants attended five learning sessions over 5 consecutive days, during which they viewed objects with novel names with/without descriptions. The older adults were as accurate as the young adults when recalling and recognizing new names during the learning sessions. With respect to response times, the older adults were as rapid as the young adults at recognizing the new names for the familiar objects, but were slower during the follow-up sessions. The older adults we...
Full text: Many studies have demonstrated significant declines in 24-hour energy expenditure (TEE) measured by whole body calorimetry with either the process of weight loss or the maintenance of reduced body weight. The aims of this study were to determine the effect of weight loss and two weeks of weight maintenance on TEE using ["1"4C]-bicarbonate-urea, Eleven subjects (6 males, 5 females), mean (#+-#SE) age 50 #+-# 3 years, BMI 34.1 #+-# 2.1 kg/m2 and body fat 38.7 #+-# 3% were studied before and after a decrease in body weight of > 8% over a period of 8 weeks, followed by two weeks of weight maintenance. Weight loss was induced using the combination of Modifast and one small meal a day (#approx#3.34 MJ/day). Body composition (DEXA), resting energy expenditure (REE) and the thermic effect of a 2.7 MJ test meal (TEF) were measured in addition to TEE at week 2 and again at week 12. Diet was assessed using diaries and physical activity ...
One of the refinements of modern Nuclear Medicine is the capacity of providing dynamic and kinetics images of the administered radiopharmaceutical, reproducing its transport mechanism, action sites, receptor binding and excretion route. With the continues technological advances new radiopharmaceuticals have been developed in order to express higher specificity and with higher characters of affinity between receptor/complex. One radiopharmaceutical is formed by a reagent or bio molecule that has in its structure a radioisotope, that has the objectives of carrying it to the organs of affinity or to benign or malign tumoral process. Somatostatin inhibits the growing and proliferation of several tumoral cells. Somatostatin analogs bind to somatostatic receptors that are expressed in different kind of neoplasia DOTA-LANREOTIDE (DOTALAN) is an octapeptide analog to somatostatin. The interest of labeling the bio conjugate with gallium-67 in Nuclear Medicine comes from its physical, chemical ...
Many epidemiological studies have investigated residential exposure to extremely-low-frequency magnetic field (ELF-MF) for children, but exposure at schools where children may stay up to 8 h every weekday was rarely considered. Between March and June 2004, we carried out a field study in Taipei City and County of northern Taiwan to explore ELF-MF exposure pattern among children at schools with high voltage transmission lines (HVTL) running through the campuses. One hundred and one children attending 14 schools with nearby HVTL (exposed group) and 123 children of 18 schools at least 100 m away from HVTL (unexposed group) were monitored for 24-hour personal ELF-MF exposure. Selected classrooms and playgrounds within the buffer regions (i.e., within 30 m of HVTL) and those away from the buffer regions were also assessed, using spot measurements, to determine the extent to which HVTL may contribute to the environmental exposure on campuses. Results ...
The data center in this study had a total floor area of 3,024 square feet (ft{sup 2}) with one-foot raised-floors. It was a rack lab with 147 racks, and was located in a 96,000 ft{sup 2} multi-story office building in San Jose, California. Since the data center was used only for testing equipment, it was not configured as a critical facility in terms of electrical and cooling supply. It did not have a dedicated chiller system but was served by the main building chiller plant and make-up air system. Additionally it was served by only a single electrical supply with no provision for backup power in the event of a power outage. The Data Center operated on a 24hour per day, year-round cycle, and users had full-hour access to the data center facility. The study found that data center computer load accounted for 15% of the overall building electrical load, while the total power consumption attributable to the data center including allocated cooling ...
All gauge theories need ``something fixed'' even as ``something changes.'' Underlying the implementation of these ideas all major physical theories make indispensable use of an elaborately designed spacetime model as the ``something fixed,'' i.e., absolute. This model must provide at least the following sequence of structures: point set, topological space, smooth manifold, geometric manifold, base for various bundles. The ``fine structure'' of spacetime inherent in this sequence is of course empirically unobservable directly, certainly when quantum mechanics is taken into account. This issue is at the basis of the difficulties in quantizing general relativity and has been approached in many different ways. Here we review an approach taking into account the non-Boolean properties of quantum logic when forming a spacetime model. Finally, we recall how the fundamental gauge of diffeomorphisms (the issue of general covariance vs coordinate conditions) raised deep ...
Measurements of the relaxation of the D{sub 2}O stretch mode in vitreous As{sub 2}S{sub 3} are presented. Because the bending mode of the molecule offers an intra-molecular decay channel for the stretch mode, the decay scheme of the D{sub 2}O molecule is more complex than that of diatomic molecules. The asymmetric stretch mode of D{sub 2}O has a frequency of 2680 cm{sup -1}. To study the relaxation of this mode we applied a pump-probe technique, using intense psec; pulses of the Stanford Free Electron Laser. Due to the small cross-section of the vibrational mode, successful efforts were made to improve the signal to noise ratio by using a laser stabilization system and a tightly focused beam to increase the intensity, by averaging the signal with a kHz repetition rate and by using samples with an optimized D{sub 2}O concentration. A rapid relaxation rate on the order of 5 x 10{sup 9} sec{sup -1} at low temperature is found that increases with temperature. Recalling ...
Non relativistic quark models have been invoked to support the statement of a 1/m{sub Q} duality violation in semileptonic B decays. However, as we recall, we have very explicitly shown that no 1/m{sub Q} duality violation is present in totally integrated rates, in such quark models. Then: 1) it is shown that some contributions under discussion are misleadingly described as '1/m{sub Q} duality violation'; as they stand, they are in fact parametrically much smaller: they are O((1/m{sub Q}){sup 5/2}) when properly referred to the total rate under discussion; numerically this is below 10{sup -2}; 2) moreover, relying on our rigorous expansion of the harmonic oscillator model around the Shifman-Voloshin limit, it is shown that even such small terms are not present at all in the total rate, and must therefore merely cancel; 3) finally, for physical masses, by an exact treatment of this particular, but not too unrealistic model, one finds a departure ...
After pioneering work in the 1980s, plasma-based ion implantation (PBII) and plasma-based ion implantation and deposition (PBIID) can now be considered mature technologies for surface modification and thin film deposition. This review starts by looking at the historical development and recalling the basic ideas of PBII. Advantages and disadvantages are compared to conventional ion beam implantation and physical vapor deposition for PBII and PBIID, respectively, followed by a summary of the physics of sheath dynamics, plasma and pulse specifications, plasma diagnostics, and process modeling. The review moves on to technology considerations for plasma sources and process reactors. PBII surface modification and PBIID coatings are applied in a wide range of situations. They include the by-now traditional tribological applications of reducing wear and corrosion through the formation of hard, tough, smooth, low-friction and chemically inert phases and coatings, e.g. for ...
After having recalled the formal convergence of the semi-classical multi-species Boltzmann equations toward the multi-species Euler system (i.e. mixture of gases having the same velocity), we generalize to this system the closure relations proposed by B. Despres and by F. Lagoutiere for the multi-components Euler system (i.e. mixture of non miscible fluids having the same velocity). Then, we extend the energy relaxation schemes proposed by F. Coquel and by B. Perthame for the numerical resolution of the mono-species Euler system to the multi-species isothermal Euler system and to the multi-components isobar-isothermal Euler system. This allows to obtain a class of entropic schemes under a CFL criteria. In the multi-components case, this class of entropic schemes is perhaps a way for the treatment of interface problems and, then, for the treatment of the numerical mixture area by using a Lagrange + projection scheme. Nevertheless, we have to find a good projection ...
The definition of episodic memory includes the concept of mental time travel: the ability to re-experience a previously experienced trajectory through continuous dimensions of space and time, and to recall specific events or stimuli along this trajectory. Lesions of the hippocampus and entorhinal cortex impair human episodic memory function and impair rat performance in tasks that could be solved by retrieval of trajectories. Recent physiological data suggests a novel model for encoding and retrieval of trajectories, and for associating specific stimuli with specific positions along the trajectory. During encoding in the model, external input drives the activity of head direction cells. Entorhinal grid cells integrate the head direction input to update an internal representation of location, and drive hippocampal place cells. Trajectories are encoded by Hebbian modification of excitatory synaptic connections between hippocampal place cells and head direction cells ...
Presently, industrial maturity can be claimed for two fuel cycle strategies, viz. the 'Once Through Fuel Cycle' (OTC), and the 'Reprocessing Fuel Cycle' (RFC) in which plutonium and very limited uranium quantities are being recycled. It is helpful to recall some key data that set the stage for any discussion of fuel cycle options: 1. Worldwide, the annual spent fuel discharge is in the range of 10500-11000 t heavy-metal (HM), while the industrial reprocessing capacity amounts to #approx# 5000 t HM (OECD NUCLEAR ENERGY AGENCY, Accelerator-driven Systems (ADS) and Fast Reactors (FR) in Advanced Nuclear Fuel Cycles: a Comparative Study, Paris, 2002). Hence, less than 1/2 of the discharged spent fuel can be processed. 2. Worldwide, the cumulative inventory of stored spent fuel is estimated to be #approx# 190000 t HM, and the amount of reprocessed spent fuel is estimated to be #approx# 70000 t HM. The latter inventory has been transformed into high-level waste (HLW) and ...
Objective: To estimate exposure dose of personnel around patients by Monte Carlo method and integration method. Methods: Exposures were estimated by a Monte Carlo practical program with Visual Basic 6.0 and integration method using 'pen-and-paper'. Results: Exposures for rectangle and ellipse sources were calculated. The difference between different methods for various sources were 0.88% and 0.61%, respectively. Conclusion: The results estimated by Monte Carlo method are close to those of integration method. It is illustrated that doses of other people estimated by Monte Carlo method are significant
The three determination methods of alpha activity ration are described, namely geometric progression method, extrapolation method and curve fitting method. The validity of the geometric progression method is demonstrated in the present work. The "2"3"8Pu/("2"3"9Pu + "2"4"0Pu) evaluated by extrapolation method is compared with that by geometric progression method. Also, the "2"3"8Pu/("2"3"9Pu + "2"4"0Pu)evaluated by curve fitting method is compared with that by geometric progression.
The general methods used to complete measurements of human exposures are identified and illustrations are provided for the cases of indirect and direct methods used for exposure analysis. The application...Full Text Available
X-ray diffraction enhanced imaging (DEI) is one of X-ray phase-contrast imaging methods, which is applied to inspect internal structures of weakly absorbing low-Z samples. The key problem of the DEI is how to extract phase information which is expressed by refraction-angle images from a series of DEI images measured in different positions of the rocking curve of the analyzer. Three effective extraction methods are presented in this paper: the statistical geometric-optics-approximation method, the maximum refraction-angle method and the Gaussian curve fitting method. They are compared with the existing methods, such as the D. Chapman's geometric optics approximation method and the multiple-images statistical method. A 2D computer simulation experiment is performed to draw comparisons of these ...
X-ray diffraction enhanced imaging (DEI) is one of X-ray phase-contrast imaging methods, which is applied to inspect internal structures of weakly absorbing low-Z samples. The key problem of the DEI is how to extract phase information which is expressed by refraction-angle images from a series of DEI images measured in different positions of the rocking curve of the analyzer. Three effective extraction methods are presented in this paper: the statistical geometric-optics-approximation method, the maximum refraction-angle method and the Gaussian curve fitting method. They are compared with the existing methods, such as the D. Chapman's geometric optics approximation method and the multiple-images statistical method. A 2D computer simulation experiment is performed to draw comparisons of these methods. ...
The paper describes advances in statistical methods for prevention research with a particular focus on substance abuse prevention. Standard analysis methods are extended to the typical research...Full Text Available
Optimization methods are applied to complex problems power systems, economics, and geodesy. Transformation methods and conjugated gradient methods are used to solve the constrained problems in power systems and economics. Conjugated gradient methods are used to solve the unconstrained geodesy problem. Broad applications of the transformation methods are emphasized. In the geodesy problem, the computational efficiency of the Fletcher-Reeves method for optimization of quadratic functions is emphasized. In this problem special storage schemes were used. The method of solution of the economics problem is compared with Beale's method.
This invention relates to new phosphor materials and to combinatorial methods of synthesizing and detecting the same. In addition, methods of using phosphors to generate luminescence are also disclosed.
In this paper, we have designed power system stabilizer (PSS) using object-oriented method. There are several types of power system stabilizer, A proportional-integral (PI) controller is very simple for practical implementation. Therefore it has been widely employed by the industry. The methods of obtaining the gains (Ki,Kp) of PI controller are root-locus method and sub-optimal regulator approach. But these methods are cannot be applicable to nonlinear system and faulted power system. So we proposed a new method which can be applied to nonlinear system by numerical analysis method. The method of dynamic system simulation by numerical method is very difficult and complex. We proposed flexible simulation method for complex power system analysis using object-oriented programming (OOP) and applied to PI ...
The defects localization in power cables follows several steps: identification, pre-localization and precise localization. Pre-localization methods, other than echo-metry, are presented first: bridge methods, particular case of low voltage networks, future perspectives. Then, the precise localization methods are described: magneto-acoustic method, audible frequencies method. The particular case of underwater and high-voltage cables is considered too (oil and gas leaks detection). (J.S.)
By the linear augmented plane wave method (APW) the energy zone of silver and technetium structure is calculated. The potential has been determined by means of superposition of atomic charge densities according to slater exchange method. Total and partial state densities have been calculated by the tetrahedron method. The APW-method convergence on the example of silver is studied, the comparison with the calculation results by the APW method and other data is carried out. The APW method high efficiency is pointed out. In dipole approximation the intensity distribution in L"3, M"5 N"3 technetium emission spectra is calculated.
...and ...and ? ...and ...and and ...and sent to discuss results ...and the moment that ...and ...and ...and and it's a great pleasure to ...and ...and because ...and ...? and ...and ...and ...? and ...? yes yes and ...and ...techniques and ...those who don't know and and i ...and ...? and ...and ...and and ...and ...and ...and ...and january nineteen seventy one and ...and ...and ...ejected johnson ? and ...saw this and that ...and the ...and ...? and ...the problem of the following talks that and ...physics and ...um and finally ...and ...and ...disposal them but that's ...and and ...and ...and that's ...and ...and ...and ...and on the physics results by michael ...and ...and evolution of detectors ...and ...and ...and ...? folks and ...and all ...and and ...and the ...and ...and ...and ...and and ...and ...and ...would be a coffee and h ? and that ...and the physics still go to forgetfulness ...and the and website and ...give you some physicists and ...and ...and ...out what the ...
The Kernel Polynomial Method (KPM) has been successfully applied to tight-binding electronic structure calculations as an O(N) method. Here the authors extend this method to nonorthogonal basis sets with a sparse overlap matrix S and a sparse Hamiltonian H. Since the KPM method utilizes matrix vector multiplications it is necessary to apply S{sup {minus}1}H onto a vector. The multiplication of S{sup {minus}1} is performed using a preconditioned conjugate gradient method and does not involve the explicit inversion of S. Hence the method scales the same way as the original KPM method, i.e. O(N), although there is an overhead due to the additional conjugate gradient part. The authors show an application of this method to defects in a titanate/platinum interface and to a large scale electronic structure calculation of ...
A method for ranking interval objects is proposed and analyzed; the characteristics of those objects are represented by pessimistic, optimistic, and most probable estimates. The method is based on the approximation of the binary probability preference relation by the binary median preference relation. The method is verified using statistical modeling (the Monte Carlo method). The proposed approach can be used for ranking nonreusable and reusable objects.
A new method of pinpointing dielectric fluid leaks on pipe-type and self-contained cables using perfluorocarbon tracer (PFT) is presented. The method has successfully been used on the Con Edison transmission system to locate leaks of dielectric fluid on both types of cables. Application of the PFT technique does not require feeder deenergization and provides major advantages over the conventional method of freeze and pressure testing. Description of the method and results of field application are presented in the paper.
Skip to Content Cancer Control and Population Sciences Home Applied Research Home Risk Factor Monitoring and Methods Home Diet Usual Dietary Intakes: Background The NCI Method Details of the NCI Method Food Intakes, US Population, 2001-04 Selected Intakes
Skip to Content Cancer Control and Population Sciences Home Applied Research Home Risk Factor Monitoring and Methods Home Diet Usual Dietary Intakes: Background The NCI Method Details of the NCI Method Food Intakes, US Population, 2001-04 Selected Intakes
A constructive method is proposed to solve a class of massive Feynman integrals within the Negative Dimensional Integration Method. The results are compared with the ones given by known positive D models and expressed in terms of dimensionally and analytically regularized integrals 3 refs.
Susceptibility disks impregnated with 35 different antibiotics were assayed by the current Code of Federal Regulations method and by a new method employing an agar overlay. The new...Full Text Available
The applicability of two nuclear analytical methods: radionuclide X-ray fluorescence analysis and radiometric titrations based on precipitate formations was studied in order to determine the heptacaine hydrochloride in solutions. The applied methods were evaluated based on the obtained sensitivity values.
The applicability of two nuclear analytical methods: radionuclide X-ray fluorescence analysis and radiometric titrations based on precipitate formations was studied in order to determine the heptacaine hydrochloride in solutions. The applied methods were evaluated based on the obtained sensitivity values. (author).
Adenosine triphosphate (ATP) is an indicator of living biomass in marine particulates. This report details the method used by Lawrence Berkeley Laboratory to analyze particulate ATP in samples taken from oligotrophic, tropical ocean waters. It represents a synthesis of previously published methods.
On the problem of alarm when parts are falling in nuclear power plant, the artificial neural network (ANN) alarm method based on the signal time-frequency characteristics was developed. The method was realized by the improved BP algorithm, and demonstrated with the data from simulation experiments
Methods of acidizing a subterranean well formation, acidizing compositions, and sequestering additives for preventing the precipitation of metal compounds in the formation are described. Use of the methods and chemicals described should lead to improved formation permeability as compared to use of previous methods and chemicals. 12 claims.
Abstracts are presented of 63 papers on the following topics: large-scale optimization, interior-point methods, algorithms for optimization, problems in control, network optimization methods, and parallel algorithms for optimization problems.
A binary mixture of imipramine HCl and chlordiazepoxide was determined by three different spectrophotometric methods. The first method involved determination of imipramine HCl and chlordiazepoxide using...Full Text Available
... Abstract : Interlaboratory evaluation of the Radiant Panel Method (ASTM E 162-67) for flame spread testing of two flexible foam and one hardboard ...
... explosive (shotgun shells, etc.) method of forming is being replaced--for the most part--by the electri- cal discharge and magnetic forming methods. ...
X-ray diffraction enhanced imaging (DEI) is applied to inspect internal structures of weakly absorbing low-Z sample. How to extract phase information from raw images measured in different positions of rocking curve is the key problem of DEI. In this paper, we present an effective extraction method called polynomial curve fitting method, in order to extract accurate information angular in a fast speed. It is com- pared with the existing methods such as multiple-images statistical method and Gaussian curve fitting method. The experiments results on a plastic cylinder and a black ant at the Beijing Synchrotron Radiation Facility prove that the polynomial curve fitting method can obtain most approximate refraction-angle values and its computation speed is 10 times faster than the Gaussian curve fitting method. (authors)
Metastable and somatically heritable patterns of DNA methylation provide an important level of genomic regulation. In this article, we review methods for analyzing these genome-wide epigenetic...Full Text Available
The invention relates to a method for purifying a gas mixture containing at least one undesirable gas compound utilizing certain sulfonamide or sulfamide solvents.
The present invention describes surfactants of formula (I), ##STR00001## wherein R, R.sub.N, and m are defined herein, processes for their preparation, and methods for their decomposition.
The possibility of gamma-absorption identification of the analyzed substance is considered. the basic provisions of the proposed method are concentrated on the example of carbohydrates and hydrocarbons. The above method is tested experimentally on polyethylenes and polystyrene
Apparatus and method are described for the vaporization of liquid fuel oils to produce a gaseous mixture suitable for burning in a burner normally designed for operation utilizing natural gas.
Dynamic clamp is a powerful method that allows the introduction of artificial electrical components into target cells to simulate ionic conductances and synaptic inputs. This method is based...Full Text Available
Slope stability can be a major problem during the construction of surface facilities. Cutting into existing ground disturbs the mechanics of the surrounding area, which can result in landslides and rock falls. This practical reference gives you the comprehensive information you need for slope stability analysis, suitable methods of analysis with and without the use of computers, and examples of common stability problems and stabilization methods for cuts and fills. It includes detailed discussions of methods used in slope stability analysis, including the Ordinary Method of Slices, Simplified Janbu Method, Simplified Bishop Method, Spencer`s Method, other limit equilibrium methods, numerical methods, total stress analysis, effective stress analysis, and the use of computer programs to solve problems. ...
The radionuclide X-ray fluorescence and particle induced X-ray emission methods were used for rapid and nondestructive analysis of metallic glasses. The methods were compared for accuracy and precision with the atomic absorption method. Some results of the analyses of Fe_xNi_8_0_-_xB_2_0 materials are briefly reviewed. The distribution of elements along the width as well as the length and a qualitative analysis of the composition of material surfaces are considered. (author).
A simple and effective method is presented for the sizing and passage apportionment of multistream plate-fin heat exchangers. Methods for passage arrangement are discussed, and it is shown that a symmetric or mixed passage arrangement is more efficient than a segregated arrangement. A method for assessing the relative merits of various passage arrangements is presented. The use of the methods is illustrated through a worked example.
The results for development of methods and computer programs for integrated optimization of parameters of perspective fast reactors are given. The possibilities of the program for the reactor campaign calculation are analysed. This program is based on utilisation of the Bubnov-Galerkin method and Wigner disturbance theory. The possibility of application of approximation methods for the optimization researches is discussed. The results of development of the programs for complex reactor computations with account of control rods system and change of physical parameters in the reactor campaign are discussed. (author).
Two methods for measuring indoor radon concentrations using activated charcoal have been tested. The first method is the well-known technique with direct gamma-measurements on the exposed canister after the sampling period. The other method uses a thermoluminescence dosemeter placed in the charcoal canister, giving an integrated value of the radon concentration.
Stability constants for uranium-tetracycline complexes were determined by the method of average number of ligands, the method of limiting values, the method of two parameters and the method of weighted least squares. Solvent extraction technique was used to obtain experimental data. (author). 10 refs.; 5 figs.
A rapid and accurate method for the direct simultaneous determination of nitrate and nitrite is proposed. The method is applied to the determination of nitrate and nitrite in rainwater and wastewater without preliminary separation. The determinations are performed by a CPA matrix method with ultraviolet spectrophotometric detection. The results obtained are in agreement with those obtained by conventional methods for the determination of nitrate and nitrite.
Pyrheliometric methods are described (particularly methods for measuring the solar constant), and theoretical and experimental studies in this field are surveyed and systematized. Particular attention is given to the analysis of instruments intended for pyrheliometers used as standards, reference instruments, and solar-constant meters is examined, and consideration is given to methods for determining the thermal-radiation properties of absorbing coatings and methods for calculating the absorption coefficients of cavity receivers.
The basic objective of this project was to consider a large class of matrix computations with particular emphasis on algorithms that can be implemented on arrays of processors. In particular, methods useful for sparse matrix computations were investigated. These computations arise in a variety of applications such as the solution of partial differential equations by multigrid methods and in the fitting of geodetic data. Some of the methods developed have already found their use on some of the newly developed architectures.
Due to biological effects of magnetic fields of high voltage transmission lines and induced effects on has pipe line, telecommunication system and interference with sensitive electronic equipment, many effort have been done to reduce transmission lines magnetic fields and several ideas have been introduced. In this paper we review three methods: phase split, shielded and compacted line methods. With aid of a developed software programme these methods are then applied to transmission lines and the results are analyzed.
Reported on here are studies of various methods for liquefying coal. Hydropyrolysis as an alternative method for producing liquid hydrocarbons and a carbon enriched char is discussed. Other methods described involve supercritical gas extraction of coal and use of natural gas as a hydrogenating agent. Relevant waste water treatments are discussed as well. 65 refs., 9 figs.
A method is provided for detecting pathological macromolecules in a patient. The method is comprised of the following: obtaining body fluid from the patient; pretreating the body fluid; subjecting the pretreated body fluid to size-exclusion chromatography to create an excluded fluid; and analyzing the excluded fluid to detect macromolecules having a predetermined molecular weight. The method also allows for comparing elution spectra with reference spectra of suspect pathologic proteins.
A new method for the determination of the cmc using a dialysis technique which allows monometric species to diffuse through but no micelles has been applied for determining the mixed micelle composition. The method is based on determining the amount of surfactant that diffuses through at two different times which allows for the calculation of the cmc by use of the appropriate equation. This method requires the preparation of only one concentration of solution and lends itself particularly well to the determination of the composition of mixed micelles. (orig.)
Objective: To develop a computerized method of internal dose estimation on radiation protection. Methods: Based on MIRD mathematic model of the organs and by means of the programming language of MS Visual Basic 6.0, a computer program of dose estimation in internal radiation was developed for radiation protection. Results: The computerized method of dose estimation for internal radiation was completed. Conclusions: This computerized method is very convenient for internal radiation dose estimation of several aspects. It can also be used in radiation accident. (authors)
A procedure for the determination of lead in various biological and environmental samples by "2"0"3Pb radioisotope dilution substoichiometric method is presented. The accuracy of the method by comparison with the literature values of reference materials appears to be good. The standard deviation of the method is less than 10%, and detection limit is about 0.1 #mu#g of lead. (author) 5 refs.
A comparison was made of Parr bomb ion chromatographic and titrimetric methods to determine sulfur in fuel oils. The two methods are comparable in precision and accuracy. When rapid sulfur determination in a number of samples is desired, the titrimetry method appears to be an appropriate choice between the two methods. l3 tables.
In this paper we present a new efficient sixth-order scheme for nonlinear equations. The method is compared to several members of the family of methods developed by Neta (1979) [B. Neta, A sixth-order family of methods for nonlinear equations, Int. J. Comput. Math. 7 (1979) 157-161]. It is shown that the new method is an improvement over this well known scheme.
In this article, we propose a model selection method, the Bayesian composite model space approach, to map quantitative trait loci (QTL) in a half-sib population for continuous and binary traits. In our method, the identity-by-descent-based variance component model is used. To demonstrate the performance of this model, the method was applied to map QTL underlying production traits on BTA6 in a Chinese half-sib dairy cattle population. A total of four QTLs were detected, whereas only one QTL was identified using the traditional least square (LS) method. We also conducted two simulation experiments to validate the efficiency of our method. The results suggest that the proposed method based on a multiple-QTL model is efficient in mapping multiple QTL for an outbred half-sib population and is more powerful than the LS method based on a single-QTL ...
The Energy Laboratory of the University of Houston has developed a computer simulation program called CREAM (Cavity Radiation Exchange Analysis Model) for application to the solar central receiver system. CREAM contains a geometric configuration factor generator based on Nusselt's method. A formulation of Nusselt's method provides the basis for a FORTRAN subroutine NUSSELT. Numerical results from NUSSELT are compared to analytic values and values from Sparrow's method. Sparrow's method is based on a double contour integral and its reduction to a single integral which is a approximated by Gaussian methods. Nusselt's method is adequate for the intended engineering applications, but Sparrow's method is an order of magnitude more efficient in many situations.
This paper proposes the use of particle swarm optimization method (PSO) for finite element (FE) model updating. The PSO method is compared to the existing methods that use simulated annealing (SA) or genetic algorithms (GA) for FE model for model updating. The proposed method is tested on an unsymmetrical H-shaped structure. It is observed that the proposed method gives updated natural frequencies the most accurate and followed by those given by an updated model that was obtained using the GA and a full FE model. It is also observed that the proposed method gives updated mode shapes that are best correlated to the measured ones, followed by those given by an updated model that was obtained using the SA and a full FE model. Furthermore, it is observed that the PSO achieves this accuracy at a computational speed that is faster than that by the GA and a full FE ...
The objectives of this study were to develop an accurate and precise method for cholesterol quantification in meat samples based on modifications made to an existing procedure (AOAC Official Method 994.10), and to apply this modified method to evaluate cholesterol levels in longissimus muscles (LM) from Angus (AN, n=5), Brahman (BR, n=4), and Romosinuano (RM, n=9) breeds. Validation of this method was performed using a meat homogenate (Standard Reference Material 1546) from National Institute of Standards and Technology (NIST), and LM samples from the three breeds with fat contents ranging from 2.4% to 9.3%. The results indicated that the modified method was accurate with cholesterol recovery exceeding 95%. The method was also found to be precise with an average coefficient of variation of...
Discussed in this report is a wavefield simulation in the 3-dimensional seismic survey. With the level of the object of exploration growing deeper and the object more complicated in structure, the survey method is now turning 3-dimensional. There are several modelling methods for numerical calculation of 3-dimensional wavefields, such as the difference method, pseudospectral method, and the like, all of which demand an exorbitantly large memory and long calculation time, and are costly. Such methods have of late become feasible, however, thanks to the advent of the parallel computer. As compared with the difference method, the pseudospectral method requires a smaller computer memory and shorter computation time, and is more flexible in accepting models. It outputs the result in fullwave just like the difference method, ...
In this thesis, a new ab-initio method for molecular dynamics within the framework of density functional theory was developed and implemented. It is strongly related to the projector-augmented-wave method (PAW) by P. Bloechl, but also includes elements of a pseudocharge method proposed by M. Weinert for the full-potential linearized augmented plane wave method (FLAPW). Like the FLAPW-method, the PAW-method is an all-electron method. In the later case, the hamiltonian takes quite a simple form similar to the one obtained when using normconserving Kleinman-Bylander-type pseudopotentials or ultrasoft Vanderbilt pseudopotentials. The PAW-method allows for an efficient calculation of systems containing virtually any element of the periodic table, including those which require high numerical effort when treated using ...
A new microdensitometry method for quantitative assessment of bone mineral content using Fuji computed radiography (FCR) was developed and the results were compared with those obtained by the conventional film-screen method. Using both methods, X-ray pictures of the 2nd metacarpal bone were taken with a reference aluminum step wedge in nine normal subjects and nine parameters representing the width and density of bone marrow and cortex were calculated in middle of the bone shaft. Interobserver reproducibility assessed for three parameters was significantly higher in the FCR method than the conventional one. The value of {Sigma}GS computed by the FCR method, that is equivalent to the net bone density of the transverse section of the shaft, showed higher correlation with the one obtained by computed tomography in comparison with the conventional method. In our FCR ...
A new microdensitometry method for quantitative assessment of bone mineral content using Fuji computed radiography (FCR) was developed and the results were compared with those obtained by the conventional film-screen method. Using both methods, X-ray pictures of the 2nd metacarpal bone were taken with a reference aluminum step wedge in nine normal subjects and nine parameters representing the width and density of bone marrow and cortex were calculated in middle of the bone shaft. Interobserver reproducibility assessed for three parameters was significantly higher in the FCR method than the conventional one. The value of #SIGMA#GS computed by the FCR method, that is equivalent to the net bone density of the transverse section of the shaft, showed higher correlation with the one obtained by computed tomography in comparison with the conventional method. In our FCR ...
Two different methods for streamlined life cycle assessment (LCA) are described: the MECO-method and SLCA. Both methods are tested on an already made case-study on cars fuelled with petrol or ethanol, and electric cars with electricity produced from hydro power or coal. The report also contains some background information on LCA and streamlined LCA, and a deschption of the case study used. The evaluation of the MECO and SLCA-methods are based on a comparison of the results from the case study as well as practical aspects. One conclusion is that the SLCA-method has some limitations. Among the limitations are that the whole life-cycle is not covered, it requires quite a lot of information and there is room for arbitrariness. It is not very flexible instead it difficult to develop further. We are therefore not recommending the SLCA-method. The ...
An exact solution method for the free vibration problem of thin circular cylindrical shells is presented. The differential equations of motion are solved directly with the use of simple Fourier series as the modal displacement functions. Stokes' transformation is exploited to obtain correct series expressions for the derivatives of the Fourier series. From this method an explicit expression of the exact frequency equation can be obtained for any kind of boundary conditions. The accuracy of the present method is checked against available data. The proposed method is then used to find the modal characteristics of the thermal liner of the Fast Test Reactor (FTR). The numerical results obtained are compared with finite element method solutions. (auth)
According to enactment of reduced dose limit based on ICRP-60, the calculation of Derived Release Limits(DRL) on Wolsung NPPs was carried out. There are two methods of determination on DRL; that is MPC(Maximum Permissible Concentration) method and system analysis method. In order to use the system analysis method, lots of environmental data are necessary and complicated exposure pathway are considered. So we intend to apply MPC method that is sort of simple. In addition the calculated results were compared with derived release limit on Canadian nuclear power plant.
Approximate methods are presented for solving nonlinear boundary value problems with an unknown (free) boundary, such as the Stefan problem in heat conductivity. Examples of this kind of problems in thermal physics, hydrodynamics, elasticity, and plasma physics are examined. Attention is given to the principal computational methods for solving stationary problems for second- and fourth-order elliptic equations, such as the domain transformation and penalty methods. To illustrate the capabilities of the methods presented here, examples of numerical solutions are presented for various specific applied problems. 255 references.
We present a numerical method for computing diffusive transport on a surface derived from image data. Our underlying discretization method uses a Cartesian grid embedded boundary method for computing the volume transport in region consisting of all points a small distance from the surface. We obtain a representation of this region from image data using a front propagation computation based on level set methods for solving the Hamilton-Jacobi and eikonal equations. We demonstrate that the method is second-order accurate in space and time, and is capable of computing solutions on complex surface geometries obtained from image data of cells.
A Monte Carlo method called transient curve fitting method was developed to calculate a eigenvalues by first simulating the existing neutrons and precursors in the system, then calculating the Eigen-distribution of neutron flux and calculating the a eigenvalues using the transient results based on the Eigen-distribution by the code TMCC. The results of this method are tested by calculating Godiva Benchmark problems and they agree well with the benchmark results. Then the reasonable results of Subcritical Facility in Tsinghua University are given by TMCC, and the results are compared with the experimental results measured by Rossi-a method. Even in the deep subcritical cases, the method can give results consistent with experimental results. (authors)
Dictionary lookup methods are popular in dealing with ambiguous letters which were not recognized by Optical Character Readers. However, a robust dictionary lookup method can be complex as apriori probability calculation or a large dictionary size increases the overhead and the cost of searching. In this context, Levenshtein distance is a simple metric which can be an effective string approximation tool. After observing the effectiveness of this method, an improvement has been made to this method by grouping some similar looking alphabets and reducing the weighted difference among members of the same group. The results showed marked improvement over the traditional Levenshtein distance technique.
This paper discusses key methods for sustaining quality engineering data, the fundamental principles that these methods are based on, and the methods for supporting the performance of nuclear power plants by the provision of quality engineering data at all times. The concept of an 'engineering data foundation', and a Configuration Management data model are developed. The concepts and methods for managing the integrity of engineering data across many different databases and document systems are developed, including the key concepts of data-positions and data-values, Master Data and Copy Data, and the concept of a 'partnership between people and technology'. (author). 7 refs., 1 tab., 2 figs.
The susceptibility to intergranular corrosion of different heats of Alloy 800 was evaluated by three different methods: the ASTM A 262 Practice E (or modified Strauss test), the Electrochemical Potentiokinetic Reactivation method, and by magnetic-susceptibility measurements. Reasonably good agreement was found between the sensitization areas as defined by the three methods in the TTS diagrams. In some cases the area defined by the Strauss test was slightly smaller than that determined by the other two tests. The differences might be explained by the fact that the methods present different sensitivities to the chromium concentration at the grain boundaries. 27 references, 11 figures, 3 tables.
The paper describes an application of the tree classification method Random Forest (RF), as used in the analysis of data from the ground-based gamma telescope MAGIC. In such telescopes, cosmic gamma-rays are observed and have to be discriminated against a dominating background of hadronic cosmic-ray particles. We describe the application of RF for this gamma/hadron separation. The RF method often shows superior performance in comparison with traditional semi-empirical techniques. Critical issues of the method and its implementation are discussed. An application of the RF method for estimation of a continuous parameter from related variables, rather than discrete classes, is also discussed.
The goal of the book is to summarize those methods for evaluating Feynman integrals that have been developed over a span of more than fifty years. The book characterizes the most powerful methods and illustrates them with numerous examples starting from very simple ones and progressing to nontrivial examples. The book demonstrates how to choose adequate methods and combine evaluation methods in a non-trivial way. The most powerful methods are characterized and then illustrated through numerous examples. This is an updated textbook version of the previous book (Evaluating Feynman integrals, STMP 211) of the author. (orig.)
Stabilized formation temperatures were estimated at different depths in 40 wells from the Los Humeros geothermal field, Mexico, using the Horner and the spherical radial flow (SRF) methods. The results showed that the Horner method underestimates formation temperatures, while the SRF method gives temperatures that are closer to the true formation temperatures. This was supported by numerical simulation of a combined circulation and shut-in period in several wells, and results for well H-26 are presented. Numerical reproduction of logged temperature is more feasible if an initial temperature profile based on the SRF method is employed instead of using an initial temperature profile based on the Horner method. (Author)
With the mentioned method to analyse O-tyrosine with HPLC/fluorescence-detection, the irradiation of chicken meat can be determined in a simple and fast way. The formation of o-tyrosine is proportional to the applied dose but because it is also depending on the applied dose rate and the temperature during the irradiation, it is not possible to control the irradiation dose. Since unirradiated chicken can contain little amounts of o-tyrosine and to confirm some results, a second method is needed. Together with one of the other mentioned methods (analysis of the volatiles or esr-spectroscopy) it is possible to recognize irradiated chicken with a high security. (author).
The stability-enchancing two-step (SETS) method has been used successfully in the Transient Reactor Analysis Code (TRAC) for several years. The method consists of a basic semi-implicit step combined with a stabilizer step that, taken together, eliminate the material Courant stability limit associated with standard semi-implicit numerical methods. This approach toward stability requires significantly fewer computational operations than a fully implicit method, but currently maintains the first-order accuracy in space and time of its semi-implicit predecessors.
Method is proposed for expanding the pile foundation elastic analysis method (displacement method) to cover a larger displacement region, and its appropriateness is verified by a field test. In this report, stability calculation is discussed in which the present displacement method is expanded by assuming an equivalent plastic hinge on the pile head and by replacing the soil spring in the large displacement region with an equivalent linear elastic spring. A static horizontal loading test is conducted for a foundation using a real pile, which is an application of this method. On the assumption that a hinge is generated on the pile head, the pile spring constant of the current displacement method is replaced with a value that takes into consideration the plastic hinge region, and this enables the analysis of pile behavior even after breakdown. This ...
In principle four different methods (ultrasound, microwaves, {gamma}-radiation and x-rays) are available for the non-destructive testing of refractories. Three of these methods, i.e. ultrasound, microwaves and {gamma}-radiation, are in use by different producers of AZS materials to carry out the quality control of their products. This paper will compare the three methods on the basis of the physical properties, present the existing devices, and show the advantages as well as the limits of the different methods. {gamma}-radiography, the oldest method in use, has one main disadvantage, which is the requirement of protection against radioactive radiation. Furthermore, while cracks and cavities can be detected with this method, structural changes can not be monitored. Therefore, the ultrasonic method was developed that allows to detect ...
This study assesses the current state of undergraduate instruction in empirical research methods in communication and offers recommendations for enhancing such instruction. Responses to an online questionnaire were received from 149 communication-related programs at four-year colleges and universities. Just over 85% of responding programs offered an empirical methods course. Although the course often covered both qualitative and quantitative methods, instruction was heavily slanted toward quantitative methods and topics common to both qualitative and quantitative inquiry. The empirical methods course was usually required for graduation, but it was typically not well integrated with the rest of the curriculum and taken late in students' undergraduate careers. Additional analyses examined st...
Deals with slope stability problems met in the D coalfield of the Tamnava-Iztok surface coal mine where 171 Mt of brown coal have been excavated and 520 Mm{sup 3} of overburden. Six geomechanical methods were used to verify the reliability of slope angels (Hoek, Froehlich, Janbu, Bishop, Reame and Swase) along with the theory of finite elements. All calculations were accomplished by means of computers. It was found that the Ream method (combined Bishop and Fellenius method) provides the most reliable results in determining general slope angles. The Janbu method is mostly suited for locations with complicated geological conditions (multi-layer benches); the Swase method may be considered as most reliable for locations with simple geological conditions and for spoil banks. 5 refs.
The difficulty and unstability of the parameter estimation of mass action model for radioimmunoassay are the major obstacles to its application in routine work. A unique robust curve fitting method for the mass action model was introduced. large numbers of simulated data were generated with Monte Carlo method to compare the accuracy and robustness of the robust fitting and the least squre fitting (Marquardt method) of the mass action model. The results demonstrated that the new robusst method significantly increased the accuracy and reliability of data processing with the mass action model. It also markedly reduced the influence of outliers in the fitting of RIA data, and it was always 'convergent'. This robust method could also be applied to other mathematical models which can be transformed into high degree equations and no initial estimates are needed for curve fitting.
In this paper, research on pass schedule of tandem cold mill (TCM) is carried out. According to load (reduction, rolling force, motor power) balance, non-linear equations set with variables of inter-stand thickness is constructed. The pass schedule optimization is carried out by solving the non-linear equations set. As the traditional method, the Newton-Raphson method is used for solving the non-linear equations set. In this paper a new simple method is brought up. On basis of the monotone relations between thickness and load, the inter-stands thickness is adjusted dynamically. The solution of non-linear equations set can be converged by iterative calculation. This method can avoid the derivative calculation used by traditional method. So, this method is simple and calculation speed is high. It is suitable for on-line control. (author)
In this paper, research on pass schedule of tandem cold mill (TCM) is carried out. According to load (reduction, rolling force, motor power) balance, non-linear equations set with variables of inter-stand thickness is constructed. The pass schedule optimization is carried out by solving the non-linear equations set. As the traditional method, the Newton-Raphson method is used for solving the non-linear equations set. In this paper a new simple method is brought up. On basis of the monotone relations between thickness and load, the inter-stands thickness is adjusted dynamically. The solution of non-linear equations set can be converged by iterative calculation. This method can avoid the derivative calculation used by traditional method. So, this method is simple and calculation speed is high. It is suitable for on-line control. (author)
In this paper, a time-domain equivalent circuit method is applied to solve dispersion of coupled-cavity travelling-wave tube (CCTWT). First, the time-domain circuit equations of CCTWT coupled-cavity chain are deduced from the equivalent circuit model. Then, the equations are solved numerically by fourth-order Runge-Kutta method and a program CTTDCP is developed using MATLAB. Last, a L-band CCTWT is calculated using CTTDCP and the cavity pass-band of this tube is computed to be 1.08-1.48 GHz, which is consistent with the experimental results and the simulation results of electromagnetic code and demonstrates the validity of the time-domain equivalent circuit method. In addition, a new design method which uses the equivalent circuit method and electromagnetic simulation together to optimize the cold cavity characteristics of CCTWT is proposed. (authors)
The present authors have previously developed a new method for Probabilistic Fracture Mechanics (PFM), which they call Recursive Distribution (RD) method. The method is based on the construction of the Lebesgue-Stieltjes measure through a deterministic mapping defining a crack growth process. In the present paper, its theoretical background is first discussed, and the Lebesgue decomposition of the measure is given. Then a numerical example of a Light Water Reactor (LWR)`s piping problem is solved by the present method, and the results are compared with those of the Monte Carlo (MC) method. In addition to leakage probability, a variation in stress cycles of the marginal distribution of an aspect ratio of a semi-elliptical surface crack is calculated, which will be used in a study on LBB evaluation.
Purpose - The purpose of this paper is to investigate the accuracy of different force calculation methods and their impact on mechanical deformations. For this purpose, a micrometer scaled actuator is considered, which consists of a micro-coil and of a permanent magnet (PM) embedded in a deformable elastomeric layer. Design/methodology/approach - For the magnetic field evaluation a hybrid numerical approach (finite element method/boundary element method (FEM/BEM) coupling and a FEM/BEM/Biot-Savart approach) is used, whereas FEM is implemented for the mechanical deformation analysis. Furthermore, for the magneto-mechanical coupling several force calculation methods, namely the Maxwell stress tensor, the virtual work approach and the equivalent magnetic sources methods, are considered and co...
A numerical analysis method for melting/solidification phenomena has been developed to evaluate a feasibility of several candidate techniques in the nuclear fuel cycle. Our method is based on the eXtended Finite Element Method (X-FEM) which has been used for moving boundary problems. Key technique of the X-FEM is to incorporate signed distance function into finite element interpolation to represent a discontinuous gradient of the temperature at a moving solid-liquid interface. Construction of the finite element equation, the technique of quadrature and the method to solve the equation are reported here. The numerical solutions of the one-dimensional Stefan problem, solidification in a two-dimensional square corner and melting of pure gallium are compared to the exact solutions or to the experimental data. Through these analyses, validity of the newly developed numerical analysis ...
The perceptual center (P-center) is fundamental to the timing of heterogeneous event sequences, including music and speech. Unfortunately, there is currently no comprehensive and reliable model of P-centers in acoustic events, so P-centers must instead be measured empirically. This study reviews existing measurement methods and evaluates two methods in detail?the rhythm adjustment method and a new method based on the phase correction response (PCR) in a synchronous tapping task. The two methods yielded consistent P-center estimates and showed no evidence of P-center context dependence. The PCR method appears promising because it is accurate and efficient and does not require explicit perceptual judgments. As a secondary result, the magnitude of the PCR is shown to vary systematically with ...
Although the radioreceptor method is widely used for estrogen receptor assay in human tissue, it has several limitations and a number of alternative methods are being explored. An immunohistochemical method of estrogen receptor assay using a specific antibody to estradiol has been proposed as a suitable alternative. The present study was designed to evaluate the validity of this method in detecting true estrogen receptors in human tumor tissue. Using radioiodinated antibody to estrogen, we have demonstrated that the estrogen antibody can detect the estrogen when it is bound to 4S type receptor but is unable to bind to estrogen when the hormone is bound to 8S type receptor. Our observations suggest that the immunohistochemical method of detection of intracellular cytosolic receptor for estrogen is not a suitable alternative to the currently used radioreceptor ...
A review of analytical design methods used for predicting reactor core flow and temperature distributions is presented with emphasis on LMFBR's. The paper also briefly describes and contrasts the methods used for LWR's. These methods are global analysis, subchannel analysis, distributed parameter, and hybrid analysis. The evolution of the local and subchannel analysis methods is presented. Data used for code validation are also presented. Current research and development needs are identified and discussed. Areas identified for future research and development include methods and expermental data for analysis of distorted bundles and natural convection. Methods that have been developed for predicting the safety performance of LMFBR's and LWR's are not within the scope of this paper.
In this paper, 0.75Pb(Fe2/3W1/3)O3-0.25PbTiO3-0.15 wt% MnO (0.75PFW-0.25PT-0.15 wt% MnO) ceramics are synthesized by two different methods, the conventional direct oxide synthesized (DS) method and two-step indirect synthesized (IS) method. The low-field dielectric responses are investigated by using the empirical law, the Curie-Weiss law, the modified-Landau theory and the spin-glass model. Due to the IS method, the lattice structure and the grain structure of the samples are changed. Furthermore, the dielectric properties are evidently modified. It is suggested that the ordering degree of B-site cations is enhanced by using the IS synthesized method.
This paper presents two imaging methods by using cross correlation. The one method images the subsurface by cross-correlation of the observed data and partial derivative seismograms calculated for a guessed model. The other method images the interface by use of cross-correlation of the virtual sources and the back propagated wave fields calculated from the observed data. Experimental tests show that both methods image subsurface interfaces well even if the guessed model is different from the true one. These imaging methods are reverse time migration that we perform cross-correlation as an imaging condition and have an advantage, as compared to conventional waveform inversion method, that images subsurface structure without iterative perturbation of the assumed model. (author). 18 refs., 15 figs.
We have developed an energy-extension method of a Bragg curve counter (BCC) at the high-energy end for the measurements of double-differential cross-sections (DDXs) of fragment productions induced by tens of MeV protons. In this method, we estimate the incident energies of the fragments penetrating a BCC on the basis of the energy loss and atomic number (Z). We applied this method to the DDX measurements of the {sup nat}C(p, Li) and {sup nat}C(p, Be) reactions induced by 70 MeV protons. The validity of this method has been confirmed by comparing the DDXs of beryllium with theoretical predictions of the PHITS code and the two-body kinematics. This method improves the energy acceptance of the BCC for light fragments twice as wide as that of a conventional method without remodeling of the BCC and any loss of the original advantages.
Abstract In 46 febrile neutropenic patients who had undergone haematopoietic stem cell transplantation, the fluorescence in situ hybridisation using peptide nucleic acid probes (PNA FISH), Gram stain/acridine orange leukocyte cytospin (Gram/AOLC), and differential time to positivity (DTP) methods were performed for detection of catheter related bloodstream infections (CRBSIs). As compared with the DTP method (which detected 11 patients with CRBSI), the PNA FISH and the Gram/AOLC methods detected ten of 11 CRBSI patients, resulting in a sensitivity, specificity, negative predictive value and positive predictive value of 91%, 100%, 97% and 100%, respectively, for the PNA FISH method as well as for the Gram/AOLC method.
In this work, a powerful analytical method, called He's parameter-expanding methods (HPEM) is used to obtain the exact solutions of non-linear modified Van der Pol's oscillator. The classical Van der Pol equation with delayed feedback and a modified equation where a delayed term provides the damping are considered. It is shown that one term in series expansions is sufficient to obtain a highly accurate solution, which is valid for the whole solution domain. Comparison of the obtained solution with those obtained using perturbation method shows that this method is effective and convenient to solve this problem. This method introduces a capable tool to solve this kind of non-linear problems.
A nodal integral method is derived for the monoenergetic, steady-state, fixed source neutron diffusion equation in hexagonal geometry based on a coordinate transformation that maps a parallelogram into a rectangle. The new hexagonal nodal diffusion method is implemented in the computer code HND where the discrete-variable equations are solved via an iterative scheme. Because the new method's equations are derived for a rhombus, they can be solved on a sequence of embedded meshes to study the method's error order. Indeed a preliminary numerical error analysis reveals a second-order error in the mesh size, and comparison with finite difference results obtained with the finite difference based BOLD-VENTURE code indicate the superior accuracy of our new nodal method.
This report is composed of the following two parts and appendix. (I) Improvement of the Method for Evaluating Reactivity Based on Monte Carlo Perturbation Theory: Theoretical formulation in Monte Carlo perturbation method had been checked, and then introduced into a calculation code. There are some cases that the results of the change of eigenvalues becomes positive or negative by changing the estimator, and there is no reasonable difference in the results between the conventional method, which does not consider the change of neutron source distribution caused by a perturbation, and the new method, which consider that change. Thus it is still necessary to check the Monte Carlo perturbation code. (II) Improvement of Nodal Transport Method for 3-D Hexagonal Geometry: We can accurately evaluate hexagonal geometry FBR core by nodal transport calculation code for hexagonal-Z geometry ...
Thalassaemic patients are in need of frequent assessment of bone age because of growth failure and pubertal disorders. To compare the ''rapid'' Greulich and Pyle (G and P) method with the third edition of the Tanner and Whitehouse (TW3) method for determining skeletal maturity and predicting final height in thalassaemic patients. A total of 191 radiographs from 58 patients (28 male, 30 female) were retrospectively evaluated by two investigators, one for each method. In 47 radiographs from 15 patients having attained their adult height, predicted final height was calculated according to each method. The mean bone ages determined by both the G and P and TW3 methods were lower than mean chronological age, although the differences were not statistically significant (10.04 {+-} 3.69 years and 9.98 {+-} 3.39 years vs. 10.78 {+-} 3.96 years, ...
UV, first, second and third derivative spectrophotometric methods have been developed for the determination of ezetimibe in pharmaceutical formulation. The solutions of standard and sample were prepared...Full Text Available
1. The short duration cerebrovascular perfusion method for measuring permeability of the blood-brain barrier has been adapted to measuring transport into the retina. 2. The method has been characterized...Full Text Available
ObjectivesThe objective of this paper is to describe the complex mixed-methods design of a study conducted to assess health-related quality of life (HRQOL) outcomes...Full Text Available
Overview Package  Class Use Tree Deprecated Index Help  PREV CLASS  NEXT CLASS FRAMES   NO FRAMES SUMMARY:  INNER | FIELD | CONSTR | METHOD DETAIL:  FIELD | CONSTR | METHOD gov.nih.nci.dc.database Class SearchCriteria java.lang.Object |
An approximate solution was proposed in which a sensitivity analysis by the storage and release of heat was performed for the subject issues and in which an operating method was thereby determined for the equipment constituting the system by means of a linear programming. Accordingly, a heat storage type energy supply system for a district cooling and heating was taken up as a concrete object to be examined. This system consisted of a gas turbine generator, initial power receiving equipment, gas boiler, electric heat pump for ice heat storage, cooling tower, heat exchanger, steam absorbing refrigerating machine, ice heat storage tank, cold and warm water heat storage tank, etc. As a result of comparison between the proposed method and the resolving method, the former showed -0.92 to 2.58% in the increase in the operating cost compared with the latter. A case where the operating cost of the resolving ...
A high-purity, intense, fast-neutron source has been developed at our laboratory. We describe two inexpensive, straightforward methods of determining the total number of neutrons produced and we review precautions to be taken in applying these methods. (orig.).
A general method is given for the construction of gauge-fixed actions for theories with local gauge symmetries. The method is based on the single requirement that the space of fields carries an irreducible representation of the Sp(2)-BRST algebra, with respect to which the resultant actions are then automatically invariant.
The parameters including knot numbers, knot positions and the weights associated with the systematic errors in the cubic spline curve fitting method were discussed. The conditions of using fitting criterion were given as well.
We propose new method of assessment of histological images for medical diagnostics. 2-D image is preprocessed to form 1-D landscapes or 1-D signature of the image contour and then their complexity is...Full Text Available
I present results for the mass spectrum of excited baryons and pentaquarks using overlap fermions and Bayesian curve-fitting method; and magnetic moments and polarizabilities for a variety of hadrons in the background field method.
I present results for the mass spectrum of excited baryons and pentaquarks using overlap fermions and Bayesian curve-fitting method; and magnetic moments and polarizabilities for a variety of hadrons in the background field method.
We have evaluated the performance of two rapid, low-cost methods for the detection of ofloxacin (OFX) resistance with 95 Mycobacterium tuberculosis isolates from countries with high...Full Text Available
Specificity of the pulses mean frequency measurement (the pulses being generated in a stochastic process) is described. Status of the domain of analog frequency meters is presented. Methods of increasing accuracy of such meters are discussed.
Specificity of the pulses mean frequency measurement (the pulses being generated in a stochastic process) is described. Status of the domain of analog frequency meters is presented. Methods of increasing accuracy of such meters are discussed. (author).
The possibility of studying the adsorption of acetic acid vapour on coal by the method of multiple attenuated total internal reflection by two proposed procedures has been shown.
This neutron reflectometry study evaluates the structures resulting from different methods of preparing polymer-cushioned lipid bilayers. Four different techniques to deposit a dimyristoylphosphatidylcholine...Full Text Available
In the present work, fast disintegrating tablets of prochlorperazine maleate were designed with a view to enhance patient compliance by direct compression method. In this method mucilage of Plantago...Full Text Available
Background and objectives: Patients receiving dialysis have a high burden of cardiovascular disease. Some receive coronary artery revascularization but the optimal method is controversial.Design,...Full Text Available
On the basis of the resolvent of a simple differential operator, a method for finding approximations to continuous functions is constructed. In this method, both the approximated function and its approximations satisfy the given integral boundary condition.
This paper proposes a novel method for computing linear basis images from tensor-valued image data. As a generalization of the nonnegative matrix factorization, the proposed method aims to approximate...Full Text Available
This thesis consists of five chapters, each of which is a self-contained unit. The first chapter overviews methods for electronic-structure calculations. Chapter 2 introduces a new method to generate a rapidly converging configuration expansion. The approach iteratively combines (1) a least-squares fitting of a configuration expansion to a many-body wave function with (2) a transfer-matrix method for projecting out the ground state. Results are shown to be equivalent to multiconfiguration Hartree-Fock. Results from test calculations are given for a simple finite difference model of the helium atom. In Chapter 3 the use of the finite-element method in electronic structure calculations is discussed. Chapters 4 and 5 discuss developments in Monte Carlo methods based on Hubbard-Stratonovich transformations. Chapter 4 introduces a canonical ensemble formulation of the ...
This article is about the network security defence method and technique at IHEP. Including: the experience, research result and application in network outlet security, server security, local network security, network security monitoring and collecting evidence, anti-virus etc
The generation of acidic mine drainage is based on the oxidation dissolution of sulfide minerals due to the contact of ores with the natural water and the air. Namely, the sulfuric acid promotes the dissolution of sulfide minerals and gangue minerals, and Fe{sup 2+} is further oxidized to turn into Fe{sup 3+}, which acts as an oxidizer for other sulfide minerals and promotes the dissolution of the same. This paper roughly describes a mine drainage treatment focusing on an Fe{sup 2+} neutralization method and an iron bacteria oxidation method. The iron bacteria oxidation method is a method of oxidizing Fe{sup 2+} into Fe{sup 3+} by using iron bacteria, and then removing Fe{sup 3+} with calcium carbonate. This method has been used for treating the drainage in the Sakuhara Mine and the former Matsuo Mine, with good results. The paper finally introduces, as power-saving low-cost mine ...
We successfully reproduce one of the French pipe whip experiments with the computer code WIPS. The WIPS results are in excellent agreement with the experimental data and the French computer code TEDEL. This justifies the use of its pipe element in conjunction with its U-bar element in a simplified method of impact analyses.
A method is proposed for operating bed waters in an oil well by injecting silanes into the near-face zone. It is distinguished by the fact that in order to improve the effectiveness of insulation, the silanes used are silanes of general formula Si /SUB n/ H /SUB 2n-n/ .
Method for description of X-ray radiation dose distribution based on semiempirical description of dose fields is suggested. At that dose field description parameters can be easily individualized for concrete X-ray device.
Method for inhibiting the formation of foulants on petrochemical equipment which involves adding to the petrochemical, during processing, a composition comprising a thiodipropionate and either a dialkyl acid phosphate ester or a dialkyl acid phosphite ester.
The present invention relates to a method of acidizing a subterranean formation or well bore employing an acidic solution containing a corrosion inhibitor composition comprising an inhibiting effective amount of an acetylenic alcohol, a quaternary ammonium compound, an aromatic hydrocarbon and an antimony compound.
In this paper method of constructing quasi-exactly solvable models of quantum mechanics is proposed. This method is based on the use of infinite-dimensional representations of simple and semi-simple Lie algebras.
In this paper, we present an iterative filtering method to estimate the background of noisy spectroscopic data. The proposed method avoids the calculation of the average full width at half maximum (FWHM) of the whole spectrum and the peak regions, and it can estimate the background efficiently, especially for spectroscopic data with the Compton continuum.
A method has been developed to predict the effects of mutations in the p53 cancer suppressor gene. The new method uses novel parameters combined with previously established parameters. The most important...Full Text Available
The neutron transport equation in Cartesian geometry possesses straight line characteristics along which the streaming operator can be written as a full differential in terms of the characteristic length. This idea was used by Lathrop to develop the step characteristic method, which he showed to be positive definite but less accurate than conventional Diamond-Difference schemes. Several authors since then have developed new methods utilizing the characteristic curves (including non-Cartesian geometry). A Linear Characteristic Method, based on a more consistent linear representation of the incoming-surface and within-cell angular flux, has been developed and tested in two-dimensional geometry producing highly accurate and computationally efficient results. A similar linear method, with several modifications, was developed for three-dimensional Cartesian geometry, and implemented in ORNL`s production code ...
In the synthesis of the peptidyl-polymer corresponding to the sequence (57-100) of the ..beta.. chain of human hemoglobin on Teflon with radiationally grafted polystyrene a comparative study was made of different methods of fragment condensation. It was shown that the most effective methods are azide condensation and condensation with the use of complex F.
In the synthesis of the peptidyl-polymer corresponding to the sequence (57-100) of the #beta# chain of human hemoglobin on Teflon with radiationally grafted polystyrene a comparative study was made of different methods of fragment condensation. It was shown that the most effective methods are azide condensation and condensation with the use of complex F.
Objective: The aim of this study was to characterize using flow cytometry cultured human primary keratinocytes isolated from the epidermis and hair follicles by different methods. Methods:...Full Text Available
Transduction method developed by the research coordinator and Prof. Muroga is one of the most popular methods to design large-scale integrated circuits, and thus used by major design tool companies in USA and Japan. The major objectives of the research is to improve capability and utilize its reusable property by combining with CAD databases. Major results of the project is as follows, (1) Improvement of Transduction method : Efficiency, capability and the maximum circuit size are improved. Error compensation method is also improved. (2) Applications to new logic elements : Transduction method is modified to cope with wired logic and FPGAs. (3) CAD databases : One of the major advantages of Transduction methods is 'reusability' of already designed circuits. It is suitable to combine with CAD databases. We design CAD databases suitable for ...
AIM: To identify a method for efficient large-scale purification of functional hepatitis B virus polymerase (HBV-Pol) without addition of cellular factors.METHODS: Full-length HBV-Pol (843 amino...Full Text Available
The Electronic REference To access In vivo Concentrations (ERETIC) method was applied to 1H HR-MAS spectroscopy. The accuracy, precision, and stability of ERETIC as a quantitative...Full Text Available
Surveys were conducted in one urban and two rural regions of the United Republic of Cameroon to estimate the annual incidence of paralytic poliomyelitis. Three different survey methods were used: a...Full Text Available
Electron spin resonance (ESR) studies have been performed on spin-labeled model membranes aligned using the isopotential spin-dry ultracentrifugation (ISDU) method of Clark and Rothschild. This method...Full Text Available
Motivation: Cell tracking is an important method to quantitatively analyze time-lapse microscopy data. While numerous methods and tools exist for tracking cells in 2D time-lapse images,...Full Text Available
A photon-induced x-ray fluorescence method allowing the simultaneous determination of iron, copper, zinc, bromine and rubidium in human blood and blood plasma samples is described. The method is reliable and has a good sensitivity for a wide range of elements. (author).
Descriptive assessment methods have been used in applied settings to identify consequences for problem behavior, thereby aiding in the design of effective treatment programs. Consensus has not been...Full Text Available
There are many methods to screen for abnormal amounts of proteinuria to identify patients at risk for progression of renal disease, but which method best predicts renal risk is unknown. Here, we analyzed...Full Text Available
A method for calculating plume rise above stack level is presented. The equations set forth by Briggs, which are presently the most popular for such calculations, are discussed. A method using 2 nomographs, simplifying the calculations is given. (JMT)
A new method for removing periodic background patterns from pictures is presented. The basic spatial frequency composition of the pattern is determined from an estimate of the power spectrum of the picture. A digital restoration filter is then created from a modified version of the power spectrum. The method is extremely effective and can be automated.
BackgroundMolecular docking methods are commonly used for predicting binding modes and energies of ligands to proteins. For accurate complex geometry and binding energy estimation,...Full Text Available
A sensitive and specific detection method was developed for Xanthomonas hyacinthi; this method was based on amplification of a subsequence of the type IV fimbrial-subunit gene fimA...Full Text Available
This article compared conceptual and empirical strengths of alternative methods for estimating racial disparities using non-linear models of health care access. Three methods were presented...Full Text Available
Two field-adapted colorimetric methods for measuring the antimalarial drug chloroquine in urine are described. Both are modifications of the method of Saker and Solomons for screening urine for phencyclidine...Full Text Available
A method is presented to derive the absolute dimensions of early-type detached binaries by combining the observed parameters with results of evolutionary computations. The method is used to obtain the absolute dimensions of nine close binaries. We find that most systems have an initial masss ratio near 1.
1. An acid ninhydrin reagent was found to react specifically in forming a pink product (Emax. 560mμ) with cysteine. 2. The method was highly sensitive for the determination...Full Text Available
In order to reduce the length and to increase the effectiveness of processing, the proposed method for acetic processing of an electric centrifugal well pump calls for covering the pressure line during the curing and periodically starting the pump.
A simplification of Sandell's method for estimating nickel in urine is described. Nickel is a normal constituent of most articles of food and between 0·01 and 0·03 p.p.m. are found in...Full Text Available
This article describes process evaluation methods for the Pool Cool Diffusion Trial across four years. Pool Cool is a skin cancer prevention program that was...Full Text Available
...specifications of ASTM Grade 1 or Grade 2 fuel oils in ASTM Method D396-04, Standard Specification for Fuel Oils (incorporated by reference, see...ASTM Grade 4, Grade 5, or Grade 6 fuel oils in ASTM Method D396-04,...
The patch and voxel methods are representative examples of the ways in which multi-slice images may be displayed three-dimensionally by means of computer-graphics. Each of them have advantages and disadvantages and they are mutually complementary. We have developed algorithms for a modified voxel method which incorporates the advantages of the patch methods. We have applied this to the three-dimensional image display of brain tumor with excellent results. The three-dimensional reconstructions used for clinical application in this study were derived from X-ray CT images.
... of the utility of the terminal outcomes, ... Other stochastic topics, such as random walks, branching ... find special uses, particularly in queueing theory ...
The authors attemps to confirm a modification of the phase-absprotion method applicable to the study of the decay rate of energy stored in the upper level in the active medium of a CO/sub 2/-laser. The essence of the method is described. Relationships are determined which allow one to obtain the unknown parameters of the experimentally measured phase shift. The work exeprimentally shows the possibility of studying vibratioanl relaxation in the active medium of a CO/sub 2/-laser by the phase-absorption method using both ordinary and isotope-substitued molecules.
Hydroxyapatite samples were produced by two different wet-chemical methods, and characterized by x-ray diffraction, infrared and compression strength measurements. The x-ray diffraction measurements were simulated using the Rietveld method, and structural data as lattice parameters and average crystallite size were obtained. The infrared spectra showed the presence of CO$_3^{2-}$ ions in all samples, indicating a contamination by these ions. By mixing samples produced by both methods, a bioceramic was obtained and, after sintering, samples with very high compression strengths (26--30 MPa) were obtained.
A car-borne NaI(Tl) spectrometric system was used together with a {sup 137}Cs source to obtain realistic data in the search for unshielded and semi-shielded orphan sources. The potassium-stripped counts (PSC) method was used to estimate the influence by the shielding on the detection ability. A reduction of about 5% in the critical distance was obtained for the semi-shielded source. A curve fitting method was also developed and evaluated. Results from the curve fitting method showed inferior ability to find the source compared to the PSC method. However, it can be a useful complementary tool, for characterisation of the source shielding, and estimation of the distance from the road.
A car-borne NaI(Tl) spectrometric system was used together with a "1"3"7Cs source to obtain realistic data in the search for unshielded and semi-shielded orphan sources. The potassium-stripped counts (PSC) method was used to estimate the influence by the shielding on the detection ability. A reduction of about 5% in the critical distance was obtained for the semi-shielded source. A curve fitting method was also developed and evaluated. Results from the curve fitting method showed inferior ability to find the source compared to the PSC method. However, it can be a useful complementary tool, for characterisation of the source shielding, and estimation of the distance from the road.
The purpose of this document is to summarize the findings of recent studies on the security problem in statistical databases and examine their applicability to the specific needs of CEDR. The document is organized as follows: In Section 2 we describe some general control methods which are available on most commercial database software. In Section 3 we provide a classification of statistical security methods. In Section 4 we analyze the type of users of CEDR and the security control methods which may be applied to each type. In Section 5 we summarize the findings of this study and recommend possible solutions.
Seeking effective methods is one of the most important goals in machinery fault diagnosis. The effective methods for gear fault diagnosis have been successively developed in our Institute. This paper is a comprehensive treatise based on our research work of recent years. A mathematical model of vibration signals for defective gears is physically described. Five effective new methods for gear fault diagnosis, such as zoom complex envelope analysis, wideband demodulation technique, bispectrum analysis, correlative spectrum analysis, and maximum entropy spectrum analysis for phase modulated signals, are summarily presented. The listed illustrations prove sufficiently the validation of these methods.
The accuracy of the carbon 14 dating method is dependent on the fluctuations of carbon 14 in the atmosphere over long periods of time. Fossil corals that are dated by both carbon 14 and uranium-thorium methods allows the setting of calibration curves for the carbon 14 method for the last 50.000 years. The uranium-thorium method is based on the measurement of the ratio of 2 isotopes: thorium 230 and uranium 234 that are both present in the decay chain of uranium 238. (A.C.)
The refractive index of novel organosilica (nano/micro)material is determined using two methods. The first method is based on analysis of optical extinction efficiency of organosilica beads versus wavelength, which is obtained by a standard laboratory spectrometer. The second method relies on the measurable trapping potential of these beads in the focused light beam (laser tweezers). Polystyrene beads were used to test these methods, and the determined dispersion curves of refractive index values have been found accurate. The refractive index of organosilica beads has been determined to range from 1.60-1.51 over the wavelength range of 300-1100 nm.
The present paper is concerned with the prediction method for the motions and tensions of mooring lines on slack-moored floating oceanic architectural building in coastal zone. The motions and the tensions of mooring lines were estimated by the time domain numerical simulation in the present method. The present method includes the nonlinearity of mooring system, slow varying wave drift force. The authors performed a time domain numerical simulation for motions and the tensions of mooring lines on floating barge in two component waves. Also, the results obtained by numerical simulation were compared with the experimental results. The validity of the present method was confirmed.
A practical method to determine the ionic diffusion coefficient and activation energy by using quasielastic light scattering (QELS) is presented. It is shown that a temperature dependence curve of the QELS intensity at a fixed frequency can be well fitted by Jonscher's formula and that the diffusion parameters can be obtained from this curve fitting. This method is successfully applied not only to crystals with high optical quality, as reported earlier, but also to opaque ceramics, which are more important than the crystals from a practical point of view. The composition dependence of the ionic diffusion coefficient is studied in sintered YbSZ to show the usefulness of this method.
A systematic optimization method of choosing the weighting matrix in linear optimal control system design, under the conditions of prespecified closed-loop dominant eigenvalue locations and feedback gain limit constraints, is presented in this paper. Studies show that with the proposed method one can obtain the desired weighting matrix very quickly and conveniently without the heavy burden of choosing a suitable weighting matrix by trail and error. This method can also easily achieve a reduced-order feedback control system. The linear optimal power system stabilizer designed by using the proposed method produces very good performance.
A method for cleaning timing optimization in a parallel steam generator system is described. The method is based on the minimization of a suitable objective function, and takes into account the load allocation on steam generators. In order to establish appropriate fouling growth models the mechanism of the particle deposition and removal on heat transfer surfaces is analyzed. The objective function is related to the short time management costs which are based on depreciation of steam generators, fuel costs and the costs of cleaning interventions. The optimization problem is described; a direct one level method is compared with a two level method. Some applications and their results are reported and discussed. (author)
The principle is described of a method using low-activity emitters as the primary radiation source for analysis. The selection of the radiation source and the detection methods including the assessment of the applicability of various radiation detectors are discussed. The benefits and the constraints of the method are considered. Practical examples are presented showing the application possibilities of the method for testing the thickness of bearing layers, piston ring coats, lead layers, etc. The possibility is shown of applying the rapid test for the composition of tungsten and chromium alloyed metal materials in testing complex systems. (J.K.).
This paper presents a new method for the determination of the energy gap of superconductors. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. The maximum voltage in differential conductance V/sub max/ was measured from the electron tunneling spectrum. From V/sub max//kT and the curve, one can easily calculate the energy gap value ..delta... This method is simple, and the accuracy almost approaches that of the curve-fitting method.
This paper presents a new method for the determination of the energy gap of superconductors. The V/sub max//kT versus #DELTA#/kT curve was calculated from tunneling theory. The maximum voltage in differential conductance V/sub max/ was measured from the electron tunneling spectrum. From V/sub max//kT and the curve, one can easily calculate the energy gap value #DELTA#. This method is simple, and the accuracy almost approaches that of the curve-fitting method.
A new method for determining the energy gap of a superconductor using the maximum in the differential conductance curve of electron tunneling spectrum is given in this paper. The V/sub max//kT versus ..delta../kT curve was calculated from tunneling theory. V/sub max/, the voltage of the conductance maximum, can be measured from electron tunneling spectrum. ..delta../kT can be found from this curve, then the energy gap ..delta.. can be calculated. This method is simple, fast and accurate. The accuracy almost approaches that of the curve fitting method.
Determination of the trajectory of a phase transition front moving in a forward or reverse direction is reduced to the solution of an ordinary differential equation. A numerical check of the results shows the method to be highly accurate. The method was used recently over a period of several years to solve various problems connected with the thawing of frozen rocks and their refreezing; among the problems considered was that of the ablation of rocks during the channeling of well, in which the method invariably proved its effectiveness. This furnishes a basis for recommending it for broader usage.
Methods are discussed for optimization of organizational model of longwall mining. Operations at a working face, their duration, number of miners, miner qualifications are analyzed. The so-called method for allocation of heteregeneous resources is used. Using the method optimum organizational models of working faces are constructed. The models consider working conditions, coal output, personnel, miner qualifications, duration of various operations and of idletime, and safety regulations. A computer code developed by the author for optimizing organizational models of longwall mining is described. 9 refs.
A technique is presented for the analyss of DNA histograms which is an extension of earlier discrete Gaussian summing methods. It alleviates the problems encountered with previous methods by extending the S-phase portions of the distribution under the G/sub 1/ and G/sub 2/ + M peaks. The resuts obtained by this method for the fraction of cells in the G/sub 1/, S, and G/sub 2/ + M phases of the life cycle are compared with autoradiographic results. With one or two exceptions which are discussed, agreement between autoradiography and the analytical method is good.
disciplinary methods were used to independently determine the aerodynamic loads, the thermal response, and strardural performance of the hydrogen cooled ...
... in the processes of production and, partic- ularly, product distribution and also by the increase in directive and disciplinary methods of intervention ...
This paper presents the status of development of Korea standard method for Human Reliability Analysis (HRA), and proposed a standard procedure and rules for the evaluation of diagnosis error probability. The quality of KSNP HRA was evaluated using the requirement of ASME PRA standard guideline, and the design requirement for the standard HRA method was defined. Analysis procedure and rules, developed so far, to analyze diagnosis error probability was suggested as a part of the standard method. And also a study of comprehensive application was performed to evaluate the suitability of the proposed rules.
In most previous studies of topology optimization, commercial programs, such as Optistruct, ANSYS, and MSC Patran, usually were used during implementation. Such commercial programs are not easy to use and entail time and cost. In addition, it is difficult to confirm results with reference to individual stages of optimization. For addressing this disadvantage, a topology optimization program, which is based on the C language, is developed in this study. This is a very convenient and powerful program for users to conduct topology optimization by using all density methods and homogenization methods in compliance with the methodology. For verifying the developed program, first of all, topology optimization was implemented by using density methods to evaluate the strain energy density of a cant...
Development of surface monitoring of the quality of round rubber packing rings for well instruments is discussed. A method is shown for testing the rings under conditions which simulate the operating conditions. A method is proposed for rapid monitoring of the conditions for vulcanization of the rings by the method of determining the ''ring modulus.''
It is possible to create nomographs similar to Fig. 2.10 to characterise damage potential of candidate time histories, provided there exists extensive records of earlier time-histories and the damage that they have caused. Thus in order to create such nomographs, one needs the correlated documentation between the input to the structure and the resulting damage. In order to use the Response-Spectra approach, one needs good statistical description of the input to the system. Extensive literature exists on both these methods. The MAC method that has being developed for the present research has yet to be validated. However, if it is successful, it would provide a valuable link between the SEA method and the rational method.
... many intriguing new possibilities in the materials sciences. Or consider solitons, a mathematical ... point out that advanced instrumentation, new materials, novel production methods, and efficient ...
The congestion cost caused by transmission capacities and voltage limit is an important issue in a competitive electricity market. To allocate the congestion cost equitably, the active constraints in a constrained dispatch and the sequence of these constraints should be considered. A multi-stage method is proposed which reflects the effects of both the active constraints and the sequence. In a multi-stage method, the types of congestion are analysed in order to consider the sequence, and the relationship between congestion and the active constraints is derived in a mathematical way. The case study shows that the proposed method can give more accurate and equitable signals to customers. (Author)
A method for automatic optimal feeder design in steel casting processes is presented. The initial design is the casting part (without feeders) which is placed in a suitable mold box. Design of each feeder contains the following steps: determination of the feeder-neck connection point on the casting surface, initial feeder design, feeder shape optimization and feeder topology optimization. Completing designing the first feeder, the method attends to designing the next one, if it is required, and the same procedure will be repeated. In the presented method, feeders are designed in a descending order of their sizes. The feasibility of the presented method is supported with an illustrative example.
In this paper we present a new, accurate form of the heat balance integral method, termed the combined integral method (CIM). The application of this method to Stefan problems is discussed. For simple test cases the results are compared with exact and asymptotic limits. In particular, it is shown that the CIM is more accurate than the second order, large Stefan number, perturbation solution for a wide range of Stefan numbers. In the initial examples it is shown that the CIM reduces the standard problem, consisting of a PDE defined over a domain specified by an ODE, to the solution of one or two algebraic equations. The latter examples, where the boundary temperature varies with time, reduce to a set of three first order ODEs.
Dynamic contingency analysis is certainly a demanding task in the context of dynamic performance evaluation. This paper presents the results of a test for checking the contingency screening capability of the IPEBS method. A brazilian 1100-bus, 112-gen system was used in the test; the ranking of the contingencies based on critical clearing times obtained with IPEBS, was compared with the ranking derived from detailed time-domain simulation. The results of this comparison encourages us to recommended the use of the method in industry applications, in a complementary basis to the current method of time domain simulation. (author) 5 refs., 1 fig., 2 tabs.
The formation mechanism of the cold-rolled strip shape with high tension was studied. An advanced method to calculate the allowable variation of strip transverse profiles was established by the strip buckling criterion, which can be more properly used in cold rolling. With this method, the aim allowable variation of the product strip transverse profile and the required transverse profile range of incoming strips can be reached. Besides, this method has been successfully applied in a domestic tandem cold mill, and the transverse profile range of incoming strips suggested with this method is more practicable and complete. Consequently, the good performance is acquired.
A versatile method for estimating the characteristics of radon transport in soil is developed. The method allows the following characteristics to be estimated: depth distribution function of the soil gas radon concentration, equilibrium radon concentration in the soil air, depth at which the radon concentration reaches its equilibrium value, radon flux density from the Earth's surface, and convective radon transport velocity. The method is based on soil gas radon concentration measurements and is appropriate in the case of relatively uniform geology. (orig.)
We propose a numerical method for resummation of perturbative series, which is based on the stochastic perturbative solution of Schwinger-Dyson equations. The method stochastically estimates the coefficients of perturbative series, and incorporates Borel resummation in a natural way. Similarly to the "worm" algorithm, the method samples open Feynman diagrams, but with an arbitrary number of external legs. As a test of our numerical algorithm, we study the scale dependence of the renormalized coupling constant in a theory of one-component scalar field with quartic interaction. We confirm the triviality of this theory in four and five space-time dimensions, and the instability of the trivial fixed point in three dimensions.
A cost effectively method to fabricate nanopores in silicon by only using the conventional wet-etching technique is developed in this research. The main concept of the proposed method is a two-step etching process, including a premier double-sided wet etching and a succeeding track-etching. A special fixture is designed to hold the pre-etched silicon wafer inside it such that the track-etching can be effectively carried out. An electrochemical system is employed to detect and record the ion diffusion current once the pre-etched cavities are etched into a through nanopore. Experimental results indicate that the proposed method can cost effectively fabricate nanopores in silicon.
Radionuclide X-ray fluorescence and particle induced X-ray emission methods were used for a rapid and nondestructive analysis of metallic glasses. The methods are compared in accuracy and precision with the atomic absorption method. Some results of analyses of Fe_xNi_8_0_-_xB_2_0 materials are briefly reviewed. The distribution of elements along the width and length, and a qualitative analysis of the composition of material surfaces are considered. (author) 3 refs.
The investigation of important wear processes in the railway technique, especially the differentiation of the parameters influencing the wear process, requires extensive test programmes and thus high resolving methods to determine the wear. Radiometric methods enable considerably greater measuring accuracy with the help of the activation of materials than an observation of measurement or measuring changes. (orig./LH).
Lipids in the stratum corneum (SC) are of major importance for the skin barrier function. Many different methods have been used for the collection of SC for the analysis of SC lipids. The objective of the present study was to validate the cyanoacrylate method for the collection of SC in relation to lipid analysis.
This article describes acoustic methods used in the in-service inspection of the dams and peripheral concrete structures of the Toktogul, Kurpsai, and Bratsk hydroelectric and pumped storage plants. The tests were conducted to assess the compression strength, elasticity, and tensile strength of the concretes. Comparative evaluations against drill core studies proved the acoustic methods to be sufficiently accurate in predicting aging behavior and loss of mechanical and physical integrity in the concretes.
Numerical results on aeroelastic standard configurations are presented. The methods used for two dimensional configurations include the small perturbations approach for inviscid flow, coupling methods for unseparated flow, coupling methods for unseparated or separated, laminar or turbulent boundary layers, and a numerical solution of the Euler equations for inviscid flow. The three dimensional configurations are studied by the transonic small disturbance approach. The detailed results are given.
The objectives of this project are to detect and characterize fractures in a naturally fractured tight gas reservoir, using surface seismic methods, borehole imaging logs, and in-situ stress field data. Further, the project aims to evaluate the various seismic methods as to their effectiveness in characterizing the fractures, and to formulate the optimum employment of the seismic methods as regards fracture characterization.
A method to deduce the 2 x 2 transport matrix for coupled heat and particle transport in Tokamaks is proposed. The method applies to perturbative experiments, and is based on a Fourier transform of the measured signals of temperature and density. By analyzing different linear combinations of temperature and density, the eigenvectors and eigenvalues of the transport matrix are determined. The method is tested for a number of illustrative cases using simulated data, and the sensitivity to noise on the signals is evaluated. (author).
The Feynman-#alpha# method was applied to measurement of reactivity and the ability of this method for a real-time reactivity monitoring system was assessed. In the experiment, all measured data by BF_3 detectors were stored in a multi-channel scaler controlled by a personal computer, and they were analyzed to obtain prompt neutron decay constant (#alpha#) and reactivity with consideration of dead time of detector. It was found that #alpha# could be obtained almost in a real-time even for both positive and negative reactivities by the present experimental technique. (author).
Simulation of the skim-off method for radon measurement by activated charcoal has been carried out by the finite elements method. The variation of radon concentration with peak appearance has been simulated. The thickness of the layer of charcoal removed after exposure and the time of peak appearance have been varied. For the charcoal and canister geometry used, the best results were found when the thickness of the layer removed was 1.72 mm.
A new multigrid algorithm based on the method of self-correction for the solution of elliptic problems is described. The method exploits information contained in the residual to dynamically modify the source term (right-hand side) of the elliptic problem. It is shown that the self-correcting solver is more efficient at damping the short wavelength modes of the algebraic error than its standard equivalent. When used in conjunction with a multigrid method, the resulting solver displays an improved convergence rate with no additional computational work.
The article explains the method of selecting the optimum energy for correcting the energy selectivity of tomographic projection and the optimum length of the crystals corresponding to it when the dual energy method in computerized tomography is used. Results of numerical calculations for actual materials and count results are presented.
We describe a large-scale application of methods for finding plagiarism in research document collections. The methods are applied to a collection of 284,834 documents collected by arXiv.org over a 14 year period, covering a few different research disciplines. The methodology efficiently detects a variety of problematic author behaviors, and heuristics are developed to reduce the number of false positives. The methods are also efficient enough to implement as a real-time submission screen for a collection many times larger.
In the present study the Pb content in Bi(2223) phase by regression or curve fitting method are optimized. The best fitting curve can be obtained by the method of least square. To study the effect of Pb content in Pb substituted Bi (2223) superconductors, prepared by solid state reaction method data is obtained. The deviation of T_c from the target value for different Pb content is summarized
Neutron activation of nitrogen and hydrogen in the body, the isotope dilution technique and the measurement of naturally radioactive potassium in the body are among the new nuclear methods, now under collaborative development by the Australian Nuclear Scientific and Technology Organization and medical specialists from several Sydney hospitals. These methods allow medical specialists to monitor the patient's response to various diets and dietary treatments in cases of cystic fibrosis, anorexia nervosa, long-term surgical trauma, renal diseases and AIDS. ills.
A novel method for processing respiratory specimens to improve culture and acid-fast staining of mycobacteria is introduced. This new method utilized N,N-dimethyl-N-(n-octadecyl)-N-(3-carboxypropyl)ammonium...Full Text Available
Microfluidic systems and methods are disclosed which are adapted to transport and lyse cellular components of a test sample for analysis. The disclosed microfluidic systems and methods, which employ an electric field to rupture the cell membrane, cause unusually rapid lysis, thereby minimizing continued cellular activity and resulting in greater accuracy of analysis of cell processes.
The invention relates to a pulsed laser ablation method of metals and/or dielectric films from the surface of a wafer, printed circuit board or a hybrid substrate. By utilizing a high-energy ultra-short pulses of laser light, such a method can be used to manufacture electronic circuits and/or electro-mechanical assemblies without affecting the material adjacent to the ablation zone.
Lead lanthanum zirconate titanate (PLZT) nanopowders with chemical compositions x/65/35 PLZT (x = 6 - 10 mol%) were prepared by sol-gel method. PLZT ceramics was obtained by the conventional sintering method and utilizing the hot pressing method. The investigations of dielectric and ferroelectric measurements of as obtained PLZT ceramics have revealed the influence of lanthanum concentration on the properties of PLZT electroceramics. (author)
A method for the analysis of three-component mixtures is described. The method is used for contact-free determination of component concentration in the mixtures transported via a product duct. Formulae as an aid in choosing the gamma radiation source and estimating the efficiency of measurement are given. The errors of measurement by the method of formaline-water-carbamide mixture is 1-2 %. 9 refs.; 1 fig.
Fractal dimensions of three different samples of lanthanum ferrite were computed using single adsorption method. The fractal Dubinin-Radushkevitch isotherm was used to fit directly the experimental nitrogen adsorption data. Avnir-Jaroniec method for fractal dimension determination was also used. Low and intermediate fractal dimensions were obtained according to BET specific surface areas.
The paper considered the vibration signals of rotating equipment as cyclo stationary signals through analyzing the features of this kind of signals. Based on the analytic method of cyclic spectrum density, the paper pointed out that the impact frequency could be extracted effectively with the help of scanning cyclic frequency domain. The validity of the method of cyclic spectrum density is proved by simulating signals and the method is applied to the diagnosis of rolling bearings. (authors)
Most algorithms for three-dimensional (3D) reconstruction from electron micrographs assume that images correspond to projections of the 3D structure. This approximation limits the attainable resolution of the reconstruction when the dimensions of the structure exceed the depth of field of the microscope. We have developed two methods to calculate a reconstruction that corrects for the depth of field. Either method applied to synthetic data representing a large virus yields a higher resolution reconstruction than a method lacking this correction.
Nondestructive inspection of carbon fibre-reinforced plastics (CRFP) using eddy current methods is based not only on the conductivity of the fibres. High frequencies (up to 10 MHz) give access to capacitive effects reflecting properties of the matrix. The paper presents a method using rotating eddy current probes to measure the anisotropic electrical properties. Potential applications of this method are the structural identification of laminates and the estimating of its degradation. (orig.)
The question about expanding the boundaries of the open pit mining method is examined. The use of methods which consider the advantages of open and underground mining operations with their joint use in horizontal and evenly dipping deposits will make it possible to objectively select the mining method, to expand the range of use of open pit mining operations in the deposits of the Far North and provide an improvement in the technical and economic indicators of mineral extraction.
A procedure for the determination of lead in soil samples by "2"0"3Pb radioisotope dilution substoichiometric method is described. Japan NIES No.2 river clay standard sample and 83-40 Tibet soil standard sample were determined. The obtained values were in good agreement with reference values. The standard deviation of the method was less then 5%. Detection limit was about 0.1 #mu#g Pb.
The method of the present invention comprises a step of previously coating a positive type resist on the surface of equipment, a step of solidifying the coated positive type resist and a step of bringing the coated equipment to circumstances for use and cleaning the positive type resist. With such procedures, the amount of radioactive materials deposited on the equipment can be reduced, and redeposition of nuclides on the surface to be cleaned can be prevented. (T.M.)
A method for elucidating complex abnormalities of CSF circulation by using a positive contrast medium (metrizamide) and computer tomography is described. The technique for the method, the results and their clinical significance is demonstrated. The value of this method is compared with traditional ventriculography and with computer tomography without the use of contrast medium. It is shown that the technique represents an important extension of the scope of computer tomography.
Out of one hundred cases of the urinary bladder abnormalities examined by this method, CT staging and pathological correlations were investigated in 61 cases of the urinary bladder neoplasms. Accuracy of CT staging was 87% in this series with possible exception of 6 cases involving the bladder base and dome. CT scan using this method is the most reliable procedure to determine the treatment modalities of the urinary bladder tumors.
The electronic structure of octahedral metal atom clusters Me_6 of 3d, 4d, and 5d transition metal atoms (V, Cr; Nb, Mo; Ta, W) has been calculated applying two different quantum-chemical approximation methods (Extended Hueckel (EH) method; SW-Xsub(alpha) method). Equilibrium structures, energy level schemes, Fermi energies and band widths as well as densities of states of clusters are discussed in detail.
To calculate the energy band structures in semiconductors using the relativistic augmented plane wave method, atomic potential and charge density are needed, which are calculated by self-consistent method. Wave function for one electron is determined by solving the Dirac equation with the Hartree-Fock equation based on the slater's exchange potential. The results of calculation for Cu"+"1 are given. (Author).
A method of calculating the neutron source strength in irradiated Fast Flux Test Facility (FFTF), fuel has been developed and is presented in this paper. This method has been used to perform calculations in support of the reactivity monitoring of the FFTF reactor by the modified source multiplication method during refueling operations. 31 refs.
We present a method for obtaining the quasi-exact solutions of the Rabi Hamiltonian in the framework of the asymptotic iteration method (AIM). The energy eigenvalues, the eigenfunctions and the associated Bender-Dunne orthogonal polynomials are deduced. We show (i) that orthogonal polynomials are generated from the upper limit (i.e., truncation limit) of polynomial solutions deduced from AIM, and (ii) prove to have nonpositive norm. (authors)
Subcritical experiments using californium source-driven noise analysis (CSDNA) and Feynman variance-to-mean methods were performed with an alpha-phase plutonium sphere reflected by nickel shells, up to a maximum thickness of 7.62 cm. Both methods provide means of determining the subcritical multiplication of a system containing nuclear material. A benchmark analysis of the experiments was performed for inclusion in the 2010 edition of the International Handbook of Evaluated Criticality Safety Benchmark Experiments. Benchmark models have been developed that represent these subcritical experiments. An analysis of the computed eigenvalues and the uncertainty in the experiment and methods was performed. The eigenvalues computed using the CSDNA method were very close to those calculated using MCNP5; however, computed eigenvalues are used in the analysis of the CSDNA method. Independent ...
Several computer assisted processing and display methods are evaluated using a series of 100 normal brain scintigrams, 50 of which have had single 'mathematical tumours' superimposed. Using a standard rating system, or in some cases quantitative estimation, LROC curves are generated for each method and compared. (author).
During the last several years, audible noise produced by high voltage transmission lines in corona has emerged as an important design consideration. In this same time frame a number of different methods for calculating audible noise levels have been proposed. The methods currently available, for both ac and dc lines, are described in this paper and are compared through application to practical line geometries for which data from long-term measurements are available.