Energy Technology Data Exchange (ETDEWEB)

Since ionic liquids (ILs) possess several attractive properties, including chemical and thermal stability, nonflammability, high ionic conductivity, and negligible vapor pressure, a new electrolyte system based on ILs has been proposed for chip type aluminum electrolytic capacitors. Four ILs based on imidazolium/pyrrolidinium cations and maleate/phthalate anions have been synthesized and their thermal stabilities have been examined. The 25wt.% solutions of the four ILs in gamma-butyrolactone (GBL) solvent were prepared as electrolytes of chip type aluminum electrolytic capacitors. The conductivity, sparking voltage and thermal stability of these electrolytes have been systematically investigated. The results revealed that the four IL-based electrolytes exhibited high conductivity. Furthermore, the conductivity of maleate anion-based electrolytes is higher than that of phthalate anion-based electrolytes, whereas the high-temperature durability of phthalate ...

Energy Technology Data Exchange (ETDEWEB)

Short communication.

UK PubMed Central (United Kingdom)

Although there have been numerous studies investigating subjective spatial impression in rooms, only a few of those studies have addressed the influence of visual cues on the judgment of auditory measures....Full Text Available

CERN Document Server

Proposal for the award of a contract, without competitive tendering, for the replacement of lift machine room equipment and the installation of remote monitoring systems

CERN Multimedia

Physicists grouped around a screen in the LEP control room at the strat-up of LEP on 14 July 1989. The emotion of the moment is clear. Carlo Rubbia, Director-General of CERN at the time, is in the centre and on his left, Herwig Schopper, former Director-General of the Organization.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

(1981). United States Guidetti, RP Luna, SF Rowland, JW Bechtel, Downey,

Energy Technology Data Exchange (ETDEWEB)

In this report, we estimated the temperature of the pump rooms and reviewed the operability of the components under the loss of the HVAC (Heating, Ventilation, and Air Condition) system. The issues relevant to the HVAC system in the PSA (Probabilistic Safety Assessment) FT (Fault Tree) model are as follows: (1) Does the loss of the HVAC system bring about a function failure of other components? (2) Can the operator take action to reduce the temperature of the room in case of a HVAC function failure? At present, we do not know whether a component will lose its function or not under the loss of the HVAC. ASME Standard describes that a recovery action can be credited if the related recovery action is included in the procedure or there are similar recovery experiences in the plant. However, there is no description about the recovery action of the HVAC in the EOP (Emergency Operation Procedure) of the UCN3, 4 under the situation of a loss of the ...

International Nuclear Information System (INIS)

On the basis of legally provided area dose measurements and time records of fluoroscopic examinations during the operation, radiation doses to medical personnel and patients are evaluated. Adequate radiation protection measures and a careful behaviour in the operating room keep the radiation exposure to the personnel below the maximum permissible exposure. Taking into account the continuous personnel radiation monitoring and medical supervision, radiation hazards in the operating room can be considered low.

Energy Technology Data Exchange (ETDEWEB)

In the paper presented, an attempt is made to describe quantitatively the room air motion by diffuse air distribution. Since solving the problem theoretically, seems to be hopeless at present, only an experimental solution seems to promise success. Experiments with diffuse air distribution offer suitable preconditions. With this kind of air introduction into the room, a relatively regular distribution of room air motion can be expected. A further simplification will be achieved by isotherme flow conditions. The first goal of the experiments was to establish whether the velocities measured are reproducible to demonstrate, and can be brought into a functional connection. The room air motion is a measured value which changes temporarily and locally quite largely, far more than is customary with technical measurements. From there, a second task arises, i.e. to evaluate the fluctuation of the velocity ...

Energy Technology Data Exchange (ETDEWEB)

This paper summarizes the findings from an exploratory definition of a usage strategy for multiple control centre wall displays in CANDU nuclear power plants. Wall displays are defined as large sized, vertically oriented display surfaces that may be positioned in various locations about a control room to support user information needs. The paper begins by discussing the need for a usage strategy for all control room information resources, and then reviews the history in wall display implementation and usage in nuclear power plant control rooms. The balance of the paper discusses the approach used in characterization and review of control room task information needs and definition of a wall display usage strategy. The paper concludes by outlining some of the possible impacts on future control room design and operations that the introduction of wall displays may imply. (author)

UK PubMed Central (United Kingdom)

Violence in both community and county hospitals in the USA is increasing. It caused significant physical, emotional and economic hardship to many emergency department employees. We describe an incident...Full Text Available

Science.gov (United States)

indications of the formation of palladium silicides. 2, 4. It has been reported .... At room temperature, palladium silicides formed in a relatively narrow interface ...

Science.gov (United States)

... at compositions below -AlP 4 the films were still unstable, hydrolysing in room air, and the long term stability of higher aluminium phosphides is in ...

Science.gov (United States)

602-906-5555 Important Links Electronic Reading Room HazMat Mgrs Tools Satellite Network Security Procedures Staff Directory Links - Partners Restricted access BLM NTC INTRANET...

Science.gov (United States)

... plans in accordance with 82nd Airborne Division Alert SOP." ... 0200 hrs, 30 August 1992, 82nd Airborne Division N+2 Room: As the Division ...

Science.gov (United States)

... is reduced: 1) by lack of oxygen, 2) in hypercapnia associated with closed rooms or tents, 3) by use of sleeping drugs, antipyretics, insulin, and 4 ...

Science.gov (United States)

DC -11/29/10 Remarks to the Press on Release of Purportedly Confidential Documents by Wikileaks; Secretary of State Hillary Rodham Clinton; Treaty Room; Washington, DC -11/29/10...

International Nuclear Information System (INIS)

Recent progress with the (Al_xGa_1_-_x)_0_._5In_0_._5P alloy system has resulted in laser diodes which operate at room temperature at wavelengths below 640 nm. OMVPE is used to grow the multi-quantum-well devices in a graded-index separate-confinement configuration. Laser threshold currents as low as 75 mA have been achieved.

Energy Technology Data Exchange (ETDEWEB)

Space HVAC systems are to provide hygienical room air. Air change is necessary because of pollutants released from materials or production processes but also because of the presence of humans or animals who consume oxygen. Poor room climate and/or poor air hygiene do not only reduce the felt comfort but may also result in a loss or profitability and higher sickness rates. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Within the framework of the IEA project Annex 20 - Airflow patters within buildings , an airflow data base was built up as a prototype. It enables airflow profiles, comfort and interior air quality to be studied without having to carry out a 1:1 experiment or having to run an expensive simulation code. The data base contains a number of pre-calculated room airflow profiles with their associated depictions of air quality and risks of drafts for given premises and for different ventilation systems. figs., tabs., refs.

Science.gov (United States)

Fires in the operating room continue to present a hazard to patients, at times with catastrophic and debilitating results. Recent data from closed claim files reveal oxygen, electrosurgical unit (ESU), and surgical drapes are common components of the fire triangle in the operating room. In this era of biotechnological sophistication, why are surgical drapes flammable? The purpose of this study was to test the flammability of different surgical drape materials and to determine the time to ignition using a bipolar ESU device in 21%, 35%, and 100% oxygen concentrations. Results show that regardless of oxygen concentration surgical drapes, when exposed to close contact with the ESU, are flammable. Time to ignition decreases with increasing concentrations of oxygen as expected. One of the surgical drapes tested was advertised to the hospital as nonflammable. Future research should focus on surgical drape materials and aim to reduce the flammability ...

UK PubMed Central (United Kingdom)

Bronchial rupture is a rare and serious complication of blunt chest trauma, which can be easily overlooked on initial evaluation in the emergency room (ER) as the focus of the attending physician is...Full Text Available

UK PubMed Central (United Kingdom)

OJECTIVEThis study seeks to identify practices of self-medication in the treatment of ocular emergencies. We examine patients’ use of both homemade preparations and manufactured...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The article presents measures for the solution of construction-biological problems and for reducing the pollutant load of buildings. (HW) [Deutsch] Der Artikel berichtet ueber Massnahmen ueber Sanierung von baubiologischen Schwachstellen und Schadstoffbelastungen in Gebaeuden. (HW)

UK PubMed Central (United Kingdom)

An outbreak with a multiresistant Klebsiella pneumoniae (MRKP) strain among seven patients admitted to the adult intensive care unit (ICU) of a regional teaching hospital in The Netherlands...Full Text Available

UK PubMed Central (United Kingdom)

A 57-year-old man with a history of coronary artery disease and placement of an implantable cardioverter-defibrillator presented at our emergency room with an anterior ST-elevation myocardial infarction....Full Text Available

UK PubMed Central (United Kingdom)

Studies of the associations between air pollution and hospital admissions and emergency room use are reviewed, including studies of air pollution episodes, time-series analyses, and cross-sectional...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Room-temperature phosphorescence (RTP) has generated considerable interest over the past several years. Several materials have been used to induce RTP from a variety of compounds. However, there is still a need to test additional materials and experimental conditions for RTP so the maximum sensitivity and selectivity can be obtained. In this work, three solid surfaces and several experimental conditions were tested for RTP of nitrogen heterocycles and aromatic amines. Nitrogen heterocycles and aromatic amines are an important class of compounds as shown by work in areas such as environmental research and coal liquefaction research. 18 references.

Energy Technology Data Exchange (ETDEWEB)

Data are presented from the intermediate scale borehole test, an in situ test fielded in the pillar separating Rooms C1 and C2 at the Waste Isolation Pilot Plant (WIPP). The test was to provide data on the influence of scale, if any, on the structural behavior of underground openings in salt. These data include selected fielding information, test configuration, instrumentation activities, and comprehensive results from a large number of gages. Construction of the test began in December 1989, with the drilling of the intermediate scale borehole in December 1990. Gage data in this report cover the period from January 1989 through June 1993.

International Nuclear Information System (INIS)

We report the radiation exposure dose received by the anesthesiologist and nurse in the orthopaedic operating room, when a fluoroscopic image intensifier is in use. This study was done in 12 femoral neck fracture operations performed from January to May 1995. Radiation was monitored with the MYDOSE MINIX PDM 107 made by Aloka Co. which were attached in front and behind the nurse's lead apron, in front of the lead apron of the anesthesiologist. The average imaging time was 9.78 min. The average radiation dose in front of the anesthesiologist is lead apron was 2.08#mu#SV, and in front and behind the nurse's lead apron were 5.67#mu#SV, 0.08#mu#SV respectively. This study and review of the literature indicate that the operating room anesthesiologist and nurse receive a lower exposure than the orthopaedist. We can disregard the problem of radiation exposure to the anesthesiologist and nurse during an orthopaedic operation when they wear lead aprons ...

Energy Technology Data Exchange (ETDEWEB)

In order to improve the long term reliability of lead-salt diode lasers, ohmic contacts of multilayer, thin-film structures consisting of In plus Au, Pt, Ni, and Pd have been studied. Diode lasers of PbSnTe fabricated with a variety of contacts were tested during room-temperature storage and during accelerated aging tests. The results show that contact reliablility can be improved when multiple overlapping films are used. After 4500 h of baking at 60 /sup 0/C, lasers with In-Au-Pd-Au contacts on both sides showed the least resistance increase (10%). For lasers with In-Au-Pt-Au contacts, 1 h of baking at 60 /sup 0/C is equivalent to 2 d storage at room temperature. Extrapolating these results, a 70% increase in contact resistance is expected for this type of laser after 9000 d of storage at room temperture. Our data also suggests that a smaller increase in contact resistance can be expected for lasers fabricated with ...

International Nuclear Information System (INIS)

Fretting wear test in room temperature water was performed to evaluate the wear coefficient of CANDU (CANadian Deuterium Uranium) steam generator (SG) tube material (Alloy 800) against 410 type martensitic stainless steels. The main focus is to compare the wear behaviors between Alloy 800 and Inconel 690. Test conditions are 10#approx#30N of normal load, 200#approx#450mm of sliding amplitude and 30Hz of frequency. The result indicated that the wear rate of Alloy 800 was higher than those of Inconel 690 at various test condition such as normal loads, sliding amplitudes etc. From the results of SEM observation, there was little evidence of plastic deformation layer that were dominantly formed on the worn surfaces of Inconel 690. Also, wear particles in Alloy 800 were released from contacting asperities deformed by severe plastic flow during fretting wear. Main cause of wear rate between Alloy 800 and Inconel 690 may be due to the difference of hardness between ...

British Library Electronic Table of Contents (United Kingdom)

The present study analyzes argument in jury deliberations by using the Conversational Argument Coding Scheme (CACS) and the content of juror argument using Subject Matter Argument Assessment (SMAA) (Pettus, 1990). The main purpose is to illustrate how the two coding schemes can complement each other to provide rich yet systematic characterization of argument in jury deliberation. Jury deliberations drawn from In the Jury Room, a televised news series on jury deliberation, are coded and analyzed using CACS and SMAA. The researchers found that using two argument coding schemes is beneficial in learning about the types of arguments jurors make and the subject matter about which they argue. The study results are compared with findings from previous studies of juror argument behavior, suggestin...

Energy Technology Data Exchange (ETDEWEB)

The results on 5 K irradiation available so far may be summarized as follows. (1) Increases of j/sub c/ following neutron irradiation occur only in conductors which are far from the optimal metallurgical treatments. (2) The changes of j/sub c/ following neutron irradiation and a thermal cycle to room temperature are small and in most cases comparable to the results obtained after 77 K irradiation. (3) The data available so far indicate that the degradation of j/sub c/ at 8 T is larger by about 5 to 10% than the corresponding changes at 5 T at a neutron fluence of 1.3 x 10/sup 22/ m/sup -2/ (E > 0.1 MeV). (4) The increase of Cu-resistivity is significant even after a thermal cycle to room temperature and requires design changes for a stable magnet operation.

Energy Technology Data Exchange (ETDEWEB)

A novel envelope-type radon monitor has been used for short-term (as little as 1 week) radon concentration measurements in a workplace environment. The commercially available LR-115 type II damage track detector was used in this study and the chemically etched sheets were spark counted. The measurements were made over a period of 1 year in a workplace consisting of three adjacent rooms situated in the lower ground level of multistorey office building in Rome, Italy. The variations of the radon concentration are from [approx] 20 to [approx] 300 Bq m[sup -3] with averages of 130,81 and 73 Bq m[sup -3] for the three different rooms resulting in annual doses of [approx] 3.8, [approx] 2.4 and [approx] 2.2 mSv, respectively. (author) 2 figs., 9 refs.

Energy Technology Data Exchange (ETDEWEB)

Good indoor air quality and thermal comfort, as well as low energy consumption, were achieved in an environment friendly experimental METOP-office building in Espoo, Finland. The consumption of heating and cooling energy was minimized by installation of energy-efficient windows, good CFC-free thermal insulation of the building envelope, the individually-controlled ventilation and room temperatures, heat recovery and energy-storing structures. According to the study carried out in 1990-1993, the heating energy was 13 kWh/m{sup 3}, 60% lower than the average consumption. The index of the satisfaction of thermal comfort was over 90%. Concentrations of all the measured indoor air pollutants were low. Ventilation rates could be chosen in each office room from 10 to 40 dm{sup 3}/s. The noise level of the ventilation system was low and the lighting level was pleasant. (author)

Energy Technology Data Exchange (ETDEWEB)

The market potential for the fan atomized burner (FAB) in water and space heating applications was examined. The major findings of the study are as follows. (1). The FAB`s low-input capability allows development of oil-fired room heaters and wall furnaces, a new market area for oil heat. (2). Among conventional oil-fired products, furnaces will benefit most from the burner`s low input capability due to (1) their quick delivery of heat and (2) their more prevalent use in warmer climates and smaller homes. (3). The greatest potential for increased product sales or oil sales exists in the use of the burner with new products (i.e., room heaters). Sales of boilers and direct-fired water heaters are not likely to increase with the use of the burner. (4). Acceptance of the burner will be dependent on proof of reliability. Proof of better reliability than conventional burners would accelerate acceptance.

International Nuclear Information System (INIS)

The initial growth process and surface structure of thin Pd(silicide) films on clean Si(111)-7x7 surfaces have been studied by low energy ion scattering (ISS) and LEED-Auger techniques. Considerable reaction between Pd and Si at room temperature is observed to extend up to 25 ML thickness of deposited Pd. Heat treatment of the room temperature film produced epitaxial silicide Pd_2Si(0001) films covered with the accumulated elementary Si layers of 1-2 ML thickness. Deposition of 1/3 ML Pd onto a heated substrate gives a Pd-embedded ordered surface of Si(111)-#sq root#3x#sq root#3R30"0, the feature being similar to the cases of Ag, Au/Si(111) systems. (orig.).

International Nuclear Information System (INIS)

The electrochemical behaviour and fracture morphology of homogenized and sensitized type SAE 304 stainless steel U bent specimens, in 3% NaCl solution, at pH=2.0 and pH=7.0 both at room temperature and 100"0C was studied. Polarization curves, galvanostatic and potentiostatic experiments were run. It could be observed that high temperature and low pH favour transgranular cracking and longer sensitization times lower fracture time and tend to give rise to intergranular fracture. Light sensitization can produce transgranular cracking even at room temperature, when the homogenized alloy does not present stress-corrosion cracking for the same condition. (Author).

Energy Technology Data Exchange (ETDEWEB)

With the combination of source ventilation and ceiling cooling for air-conditioning of working and recreation rooms, a ventilation system is available which fulfills the highest demands regarding thermal comfort. In order to utilize the advantages of this ventilation system with regard to air quality and thermal comfort to an optimum, the influence of the radiation exchange between cooling ceiling and walls on the flow in the room is investigated experimentally. Energy transfer from the walls to the cooled ceiling may result in an insufficient temperature of the walls compared to ambient air and in an upward flow on the wall surfaces (downward flow of) driven by gravity, which influences the flow pattern in the case of source ventilation. (orig.)

International Nuclear Information System (INIS)

The characteristics of infrared-stimulated luminescence (IRSL) from a sample of potassium feldspar at low temperatures are presented. These studies extend the previous work from this laboratory on the optical bleaching characteristics and emission spectra of feldspars at room temperature and recent measurements of the stimulated spectrum for a sample of potassium feldspar at room temperature. Stimulation spectra have been measured at 290, 160 and 145 K. By fitting Gaussian functions to the spectra, the peak position is shown to shift to higher photon energies at lower temperatures and the full-width half-maximum of the peak to reduce with decreasing temperature. The variation of IRSL intensity with temperature for several stimulating wavelengths has been determined and the form of the IRSL decay curve measured at 290 and 160 K. No substantial differences were observed in the form of the decay curves at each temperature. (author).

Energy Technology Data Exchange (ETDEWEB)

One chemical reagent, hydrazine hydrate, was discovered to accelerate the growth of semiconductor nanocrystals (cadmium telluride) instead of additional energy, which was applied to the synthesis of high-quality CdTe nanocrystals at room temperature and ambient conditions within several hours. Under this mild condition the mercapto stabilizers were not destroyed, and they guaranteed CdTe nanocrystal particle sizes with narrow and uniform distribution over the largest possible range. The CdTe nanocrystals (photoluminescence emission range of 530-660 nm) synthesized in this way had very good spectral properties; for instance, they showed high photoluminescence quantum yield of up to 60%. Furthermore, we have succeeded in detecting the living Borrelia burgdorferi of Lyme disease by its photoluminescence image using CdTe nanocrystals.

Energy Technology Data Exchange (ETDEWEB)

This invention relates to an automatically-operating wedge block for maintaining intimate structural contact over wide temperature ranges, including cryogenic use. The wedging action depends on the relative thermal expansion of two materials having very different coefficients of thermal expansion. The wedge block expands in thickness when cooled to cryogenic temperatures and contracts in thickness when returned to room temperature.

International Nuclear Information System (INIS)

The mechanism for afterglow suppression in codoped CsI:Tl,Eu reported in the preceding paper was investigated by combined radioluminescence and thermoluminescence experiments. Model rate equations informed by these experiments were employed to simulate afterglow. It was found that codoping with europium introduces deep electron traps, with room-temperature glow peaks, that effectively scavenge the electrons from shallow traps associated with thallium, thus suppressing afterglow in the time domain of tens of milliseconds.

Energy Technology Data Exchange (ETDEWEB)

An intermetallic compound Sm[sub 2]Fe[sub 17]N[sub x] was synthesized by plasma nitriding of Sm[sub 2]Fe[sub 17] in a stream of N[sub 2]-H[sub 2] mixed gas. The reaction proceeded at a lower temperature (around 423 K) than that of the conventional thermal technique, but not at room temperature. This is discussed on the basis of the difference between the reaction mechanisms of plasma and thermal nitridings. (orig.)

International Nuclear Information System (INIS)

The irradiation of air produces some toxic gases such as ozone, nitric oxide, nitrogen dioxide, nitrogen trioxide, nitrogen tetroxide, nitric anhydride and nitrous oxide. Of these gases, ozone is the most important because of its toxicity and may be produced in such quantities as to constitute a health hazard within the irradiation room. The toxicity, and explosive characteristics of ozone and quantitative aspects of ozone production are discussed and ventilation requirements considered. (U.K.).

International Nuclear Information System (INIS)

To optimize the emergency care of patients with multiple injuries, a special emergency room with integrated radiological equipment has been developed. It consists of a linear array of a computed tomography system, a mobile C-arm with an integrated scattered radiation grid for conventional films and a C-arm fluorographic system. The intent is to avoid delay caused by transport and repositioning of the patient. It enables all necessary diagnostic procedures to be performed within a minimal amount of time. (orig./MG).

International Nuclear Information System (INIS)

Concentrations of 226Ra, 232Th, and 40K measured in bauxite waste, local building materials, and soils are presented and used in model equations to estimate the effective gamma dose-equivalent increments over background in the center of a standard-sized room in a prototype house. Calculated and measured values compare reasonably well.

Energy Technology Data Exchange (ETDEWEB)

X-ray diffraction was used to monitor the {ital in} {ital situ} reaction of Pd deposited on Si(111) at room temperature. An ordered silicide forms spontaneously beneath a poorly ordered overlayer. It is commensurate and strained at low coverage, but relaxes to an unstrained state above a critical thickness of 18 A. During both phases of growth sustained intensity oscillations are seen that correspond to a layerwise consumption of the substrate at the buried interface.

International Nuclear Information System (INIS)

The Grueneisen parameter and lattice thermal expansion of the A-15 compounds V_3Si and V_3Ge at room temperature are evaluated on the basis of the method due to Brugger and Fritz from the third order elastic constants reported earlier. The calculated values are compared with available experimental values and are found to fit satisfactorily. (author).

Energy Technology Data Exchange (ETDEWEB)

The results of Sandia National Laboratories' participation in the NASA Planetary Definition and Design Program are summarized. Areas reported include the characterization of large area cadmium zinc telluride spectrometers and the application of simulation techniques to the prediction of device performance. Also investigated was the response of mercuric iodide devices in the region from 1 to 100 KeV. A literature study to determine the status or radiation damage measurements in room temperature semiconductor devices is also reported.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys and composites are potentially highly attractive materials for lightweight design in the automotive industry - if common forming technologies, i.e., deep drawing and cold extrusion, are applicable to them; so far, this is seldom the case. The authors have tested some candidate Mg alloys and discuss the results of their measurements in detail. The Figure shows a typical workpiece part obtained by a deep-drawing technique. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The construction of Heavy Ion Medical Accelerator in Chiba (HIMAC) at the National Institute of Radiological Sciences was completed in December 1993. HIMAC consists of an injector linac, two synchrotron rings, a high energy beam transport system and a beam irradiation system. Its accelerator parameters are based on the medical requirement, and helium, carbon, neon, silicon and argon were selected as the accelerated ion species. It has 3 therapy rooms (A{approx}C). Room A has a vertical irradiation system, Room C horizontal and Room B both vertical and horizontal. Two rings can supply beams independently to the vertical and horizontal irradiation systems. Clinical trial started on June 21 1994, after several basic biological and physics experiments lasting about 2 months. Cancer is the top cause of death in Japan since 1981, and people expect good treatment results at HIMAC. Proton and heavy ion ...

Energy Technology Data Exchange (ETDEWEB)

The detector for retrospective radon exposure measurements is developed. The detector consists of the multilayer package of solid-state nuclear track detectors LR-115 type. Nitrocellulose films works both as {alpha}-particle detector and as absorber decreasing the energy of {alpha}-particles. The uncertainties of implanted {sup 210}Pb measurements by two- and three-layer detectors are assessed in dependence on surface {sup 210}Po activity and gross background activity of the glass. The generalized compartment behavior model of radon decay products in the room atmosphere was developed and verified. It is shown that the most influencing parameters on the value of conversion coefficient from {sup 210}Po surface activity to average radon concentration are aerosol particles concentration, deposition velocity of unattached {sup 218}Po and air exchange rate. It is demonstrated that with the use of additional information on surface to volume room ...

British Library Electronic Table of Contents (United Kingdom)

In this research, new thin freestanding films of poly(methyl methacrylate) (PMMA)/50% epoxidised natural rubber (ENR 50) were doped with lithium triflate, LiCF3SO3 salt was prepared by a solvent casting method. The incorporation of ENR 50 is found to increase the conductivity of PMMA/LiCF3SO3 by two orders of magnitude at room temperature. The highest conductivity achieved was 5.09x10-5Scm-1 at room temperature when 60% of LiCF3SO3 salt was introduced into the PMMA blend containing 10% ENR 50. The formation of excessive hydrogen bonds and interchain crosslinking limit the performance of the blend at higher concentrations of ENR 50. The ionic conduction mechanisms in PMMA/ENR 50/LiCF3SO3 electrolytes obey the Arrhenius rule in which the ion transport in these materials is thermally assisted...

Energy Technology Data Exchange (ETDEWEB)

The amorphization of a quenched sample of the GaSb-II high-pressure phase was studied at ambient pressure by real-time neutron diffraction in the course of the sample heating from 100 K to room temperature at a rate of 0.4 K min{sup -1}. The transformation to the amorphous state begins at 140 K and is completed near room temperature. The {beta}-Sn type structure was shown to represent only the mean lattice of the high-pressure GaSb-II phase. The superstructure of this phase widely varied with temperature and is caused by the ordered displacement of atoms. The temperature range of the metastable crystalline phase relaxation is divided into three intervals according to the temperature dependence of the tetragonality ratio (c/a). At the boundaries of these temperature intervals, i.e. temperatures T = 170 and 230 K, two second-order phase transitions are observed. Anomalous heat and volumetric effects were observed earlier by means of calorimetry ...

Energy Technology Data Exchange (ETDEWEB)

Data are presented demonstrating very-short-wavelength (625 nm) room-temperature (300 K) continuous (cw) photopumped laser operation of In/sub 1-//sub y/(Al/sub x/Ga/sub 1-//sub x/)/sub y/P-In/sub 1-//sub y/ (Al/sub x/Ga/sub 1-//sub x/)/sub y/P quantum well heterostructures grown lattice matched (yapprox. =0.5) on a GaAs substrate via metalorganic chemical vapor deposition. In addition, 300 K pulsed laser operation (J/sub th/approx.10/sup 4/ A/cm/sup 2/, 625 nm) of diodes fabricated from the same crystal is described.

Energy Technology Data Exchange (ETDEWEB)

Building 922 houses all of SNL/California`s ES and H Departments: Health Protection, Environmental Protection, Safety, and Environmental Operations. It covers approximately 10,000 square feet and houses about 80 people. The office personnel generate nonhazardous solid office wastes in their daily activities. To determine the types and amounts of waste generated, a special PPOA sorting team sorted all of the trash collected from the building for a period of one-week (including paper and aluminum cans in the recycling bins). The team sorted the trash into major categories: paper, plastic, metals, glass, wet garbage, rest room waste, and miscellaneous materials. They then sorted it into subcategories within each major category. Rest room waste was collected but not sorted. The waste in each category was weighed separately. The total amount of trash collected during the week was approximately 168.8 kg (371.4 lbs). The results of this PPOA indicate ...

British Library Electronic Table of Contents (United Kingdom)

Herein, we report engineering of nanostructured p-CuIn3Se5/n-CdS heterojunction thin film on a glass substrate, which is prepared at room temperature using simple wet chemical approach involving ion exchange reactions between CdS and Cu^+, In^3^+ and Se^2^- ions in alkaline medium. The uniform deposition of heterojunction thin films is achieved by optimizing the pH, temperature and molarity of the reactant bath. The as-deposited thin-films were annealed at 200^oC in air for 1h and further characterized for structural, optical and electrical properties using UV-Vis spectrophotometer, X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy (XPS), Hall effect for type of conductivity, and I-V measurement to investigate the char...

Energy Technology Data Exchange (ETDEWEB)

Ho{sub 2}CuTiO{sub 6} double pervoskite is synthesized by solid state reaction method and the phase formation was confirmed by X-ray diffraction. Ho{sub 2}CuTiO{sub 6} crystallizes in space group P63 cm and are isostructural in AMnO{sub 3} structure. We have investigated the effect of the presence of a magnetic ion (Ho{sup 3+}{approx}10.4{mu}{sub B}) in Ho{sub 2}CuTiO{sub 6}, on the magnetic properties, compared to that of an isostructural double perovskite containing Y-ion (non-magnetic), i.e., Y{sub 2}CuTiO{sub 6}. Magnetization measurements on Ho{sub 2}CuTiO{sub 6} showed paramagnetic moment of 0.026{mu}{sub B}/Ho at room temperature in an applied field of 7 T although no saturation is observed at room temperature, whereas, at 5 K, the paramagnetic moment was 0.3{mu}{sub B}/Ho in the same field. Since this compound is non-centrosymmetric, it is of interest to look into the possibility of realizing multiferroicity (coexistence of magnetic and ...

Energy Technology Data Exchange (ETDEWEB)

Energy requirements and exergy inefficiencies for processing of malt drink were estimated for a Nigerian brewery. The process was divided into twenty-one basic unit operations and grouped into four main group operations: silo house, brew house, filter room and packaging house. The energy intensity for processing a batch of 9.8 tonnes brew grains to 562 hl of malt drink was estimated as 261.63 MJ/hl consisting of electrical (41.01%), thermal (58.81%) and manual (0.19%) of the total energy. The most energy intensive group operation was the Packaging House operation, followed by the Brew House operation with energy intensities of 223.19 and 35.94 MJ/hl, respectively. The exergy analysis revealed that the packaging house operation was responsible for most of the inefficiency (92.16%) followed by brew house operation (7.17%) and the silo house and filter room operations with less than 1% of the total exergy lost. The most exergy loss took place in ...

International Nuclear Information System (INIS)

Tensile properties of reduced-activation 10Cr-30Mn austenitic steels with carbon levels from 0.003 to 0.55% were investigated over the temperature range from room temperature to 873 K after neutron irradiation in the Japan Materials Testing Reactor at 573 K to 8.5x10"2"2 n/m"2. Irradiation-induced increase in yield stress increased significantly with carbon concentration up to about 0.1% and it was constant above 0.1% carbon. A high density of dislocation loops with small (below 10 nm) and large (20-30 nm) sizes formed during irradiation. The high density, small loops caused a large irradiation hardening, while the large loops contributed only slightly to irradiation hardening. It was considered that carbon atoms formed the small loops together with irradiation defects. The deformation channeling was observed in the irradiated high carbon steels, 0.11 and 0.55% carbon, but not in the very low carbon steel, 0.003% carbon, after deformation near ...

Energy Technology Data Exchange (ETDEWEB)

Deformation mechanisms of Mg-Al-Zn (AZ31) alloys were investigated by performing tensile test at room temperature. In fine grain Mg alloys deformed at room temperature, nonbasal slip systems were found to be active as well as basal slip systems because of grain-boundary compatibility effect. Slip-induced grain-boundary sliding occurred as a complementary deformation mechanism to give rise to c-axis component of strain. With increasing grain size, the activation of the nonbasal slip systems was limited near grain boundaries. Instead of grain-boundary sliding, twinning occurred as a complementary deformation mechanism in large grained samples. Orientation analysis of twins indicated that twinning is induced by stress concentration due to the pile up of basal dislocations. The grain-size dependence on deformation mechanism was found to affect yielding behavior both microscopically and macroscopically which can influence various mechanical ...

Energy Technology Data Exchange (ETDEWEB)

In supervising CANDU plant operation, Operations staff must routinely monitor plant status using information from several information systems. One key source of plant status information are the CRT displays at console workstations and panel locations. At Darlington, as at most CANDU plants, Operations staff have adopted a reference set of displays for use in monitoring during Full Power Steady State conditions. The display set employed was chosen from the available suite of displays, and operational experience has demonstrated that the current displays could be improved. For Outages, no reference display set has been defined, and for Upset conditions, the current Transient display set does not provide the information needed by operations staff, and consequently is not used. This paper describes the basis for and findings from a COG project [1] undertaken in 1997 to characterize monitoring practice and develop improvements to control room displays to better support ...

Energy Technology Data Exchange (ETDEWEB)

Authors already reported the integrated system so called SODAS (System Of Design and Assembling for Shipbuilding) which was based on product model concept. And products in shipbuilding industry today are not limited to ship structures alone. Therefore, it is desirable that a more global product model which can describe another products such as offshore structures should be considered. In this paper, a product model of offshore structures is discussed. Compared with the case of ship structures, the distinctive feature in the design stage of offshore structures lies in the initial design stage. Thus in this paper, some of the new model in initial design stage are introduced. Some of them are `Function Element Model` which expresses functional concept by designers. In the other design stage, product information such as `Room` and `Part` which were already introduced in SODAS are used effectively for a product model of offshore structures. By the use of product ...

British Library Electronic Table of Contents (United Kingdom)

We propose and demonstrate a facile room-temperature synthetic method for obtaining water-soluble magnetic Fe3O4 nanoparticles (NPs) by combining the in situ synthesis and decomposition of a magnetic polymer hydrogel. The Fe3O4 NPs with average diameters of 6.3-8.3nm were synthesized in a cross-linked polyacrylamide (PAAm) hydrogel by coprecipitating iron ions. The decomposition of the magnetic polymer hydrogel by an aqueous solution of sodium hydroxide led to the transfer of Fe3O4 NPs into the aqueous medium. The NPs can be dispersed stably in water for more than three months. The Fe3O4 NPs were characterized by X-ray photoelectron spectra (XPS), X-ray powder diffraction (XRD), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FT-IR). The saturation magn...

Energy Technology Data Exchange (ETDEWEB)

The ``Passivhaus Darmstadt-Kranichstein`` is a 4 unit terrace house with an extremely low total annual energy consumption of less than 32 kWh/m{sup 2} of living area, thereof about 12 kWh are needed for room heating. The determining factors for the low consumption are the superinsulation, airtightness of the thermal envelope in combination with a highly efficient VAV ventilation system, and an improved window construction. The results of a detailed monitoring program allow decisive statements concerning reduction of energy consumption, relief of environment, indoor air quality, and thermal comfort. (author)

International Nuclear Information System (INIS)

The full scope simulator in Daya Bay Nuclear Power Station is imported from THOMSON-CSF company in France. It is a large facility, using digital simulation technology, that simulate the main control room of Daya Bay Nuclear Power Station with the high fidelity. It is used for training operators; system analyzing including operation procedure verification. The input output interface system of the simulator is the bridge of the information exchange between instrumentation and the computer. From the point of view of data transfer, this paper discusses the operation principle of the I/O interface system.

Science.gov (United States)

The results of an investigation into the behavior of adhesively bonded doubler splices of two composite material sandwich panels are presented. The splices are studied from three approaches: analytical; numerical (finite elements); and experimental. Several parameters that characterize the splice are developed to determine their influence upon joint strength. These parameters are: doubler overlap length; core stiffness; laminate bending stiffness; the size of the gap between the spliced sandwich panels; and room and elevated temperatures. Similarities and contrasts between these splices and the physically similar single and double lap joints are discussed. The results of this investigation suggest several possible approaches to improving the strength of the sandwich splices.

International Nuclear Information System (INIS)

We have prepared high-quality, single crystals of SmB_6 under various conditions to improve sample quality. We have measured the resistivity and magnetic susceptibility from room to liquid-helium temperatures to sort samples. We have applied pulsed magnetic fields as high as 50 T at temperatures as low as 40 mK while measuring resistivity. Our samples are of higher quality than previously known. All solvent-grown, single-crystal samples should be etched to remove a surface conductivity. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The reactions of native bovine catalase with superoxide and solvated electrons have been investigated using three different methods for generating these reducing substrates: [gamma]-radiolysis of oxygenated or deaerated buffer solutions in the presence of an OH radical scavenger; either xanthine or acetaldehyde with xanthine oxidase; and low-temperature (77 K) [gamma]-radiolysis of buffered ethylene glycol/water solutions with subsequent annealing of samples at 183 K. (Author).

International Nuclear Information System (INIS)

Gallium liquid-metal ion sources that have been introduced in the late 1970s have allowed the development of a new class of micro- and nanofabrication tools collectively denominated as focused ion beam (FIB) machines. To investigate the potential of a helium beam in such a FIB instrument the authors have tested a room-temperature electron beam ion trap coupled with a high resolution FIB machine. In this letter they present their first results in target imaging using a helium beam with a resolution that allows to account for a beam diameter in the submicrometer range.

Energy Technology Data Exchange (ETDEWEB)

Arrays of CdS:Mn{sup 2+}:Cu{sup +} micro- and nanowires grown in polycarbonate ion-track templates exhibit photoluminescence in the spectral domain ranging from 500 to 800 nm at room temperature. A comparison with similar CdS and CdS:Mn{sup 2+} wire arrays is presented. The individual contributions to the emission spectra of Cu{sup +} and Mn{sup 2+} ions in the CdS matrix are explained using their energy level schemes. Also SEM, EDX and EPR data are given for these wires. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Science.gov (United States)

Deformation experiments performed in-situ in the transmission electron microscope have led to an increased understanding of dislocation dynamics. To illustrate the capability of this technique two examples will be presented. In the first example, the processes of work hardening in Mo at room temperature will be presented. These studies have improved our understanding of dislocation mobility, dislocation generation, and dislocation-obstacle interactions. In the second example, the interaction of matrix dislocations with grain boundaries will be described. From such studies predictive criteria for slip transfer through grain boundaries have been developed.

Energy Technology Data Exchange (ETDEWEB)

Neon 19, a 17-second positron-emitting radioelement, is produced continously by 23 MeV alpha particle bombardment of oxygen. For a 12 ..mu..A particle current the method of preparation described delivers 14 mCi of neon 19 per min to the functional exploration room. The radiochemically pure radioactive gas is diluted in air and breathed continously by the patient lying under a positron tomographic camera. The regional lung ventilation distribution is obtained on 2 cm thick sections of organ with a transverse resolution of 17 mm. Quantification of the ventilation output per unit lung volume is contemplated.

Science.gov (United States)

nsive neutron-absorbing bricks from commercially available CaB/sub 6/ powder. The bricks are 2 x 3 x 5 in., and are strong enough to withstand normal handling. They last indefinitely; the ones described are now 7 years old, used and stored under normal room temperatures and humidities. The procedure is to make a thick, dry mud with the powder and water, followed by compression in a mold at pressures of about 1 ton/in./sup 2/ or more. The bricks are then baked for 2 hours or longer at a temperature of about 750 deg C. (auth)

Energy Technology Data Exchange (ETDEWEB)

This guide is applied for the reload pattern's formation for mirror symmetry of a core room and in accordance with the Control Cell core technique (of the english Control Cell Core - CCC) for the PRESTO-B code. (Author)

Energy Technology Data Exchange (ETDEWEB)

We report a study of the nonmetal-metal transition of free-standing Pd{sub N} clusters (2{<=}N{<=}21) carried out through two different theoretical approaches that are extensively employed in electronic structure calculations: a semi-empirical tight-binding (TB) model and an ab initio DFT pseudopotential model. The calculated critical size for the metallic transition decreases rapidly with the temperature and an oscillatory dependence with the cluster size is obtained, particularly in the DFT approach. The TB model describes the metallic behavior for cluster sizes beyond N{approx}12 well. Our obtained critical size at room temperature is of the order of the experimental estimation.

Science.gov (United States)

We have grown crack-free antiferroelectric (AFE) Pb{sub 0.92}La{sub 0.08}Zr{sub 0.95}Ti{sub 0.05}O{sub 3} (PLZT) films on nickel foils by chemical solution deposition. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, we applied a conductive buffer layer of lanthanum nickel oxide (LNO) on the nickel foil by chemical solution deposition prior to the PLZT deposition. Use of the LNO buffer allowed high-quality film-on-foil capacitors to be prepared at high temperatures in air. With the AFE PLZT deposited on LNO-buffered Ni foils, we observed field-induced phase transformations of AFE to ferroelectric (FE). The AFE-to-FE phase transition field, E{sub AF} = 260 kV cm{sup -1}, and the reverse phase transition field, E{sub FA} = 220 kV cm{sup -1}, were measured at room temperature on a {approx}1.15 {micro}m thick PLZT film grown on LNO-buffered Ni foils. The relative permittivities of the AFE and FE states were {approx}530 ...

Energy Technology Data Exchange (ETDEWEB)

The application of medium energy ion scattering in combination with channelling and blocking to the study of the initial stages of palladium silicide formation is discussed. After a brief description of the experimental arrangement and method, the effects on the Rutherford backscattering spectra of depositing small quantities of palladium on clean Si(111) are reported. The uniformity and thermal stability of thin palladium silicide films grown at room temperature were measured. Finally, channelling and blocking results were used to carry out a structural analysis of thin epitaxial Pd/sub 2/Si layers.

Energy Technology Data Exchange (ETDEWEB)

This paper analyses the errors caused by interpolation from existing cases for assessing indoor air flow, air quality and thermal comfort in an office. A sensitivity study is then provided to determine the influence of several boundary conditions on indoor air diffusion. The research is conducted numerically by using a low-Reynolds-number k-{epsilon} model. It can be concluded that the interpolation errors caused by the variations of solar radiation, window size, heat source location due to lighting, and the surface temperatures of interior walls are small and can be quantitatively determined. But it is difficult to estimate the errors introduced by the variations of furniture location and size. (author).

Science.gov (United States)

By gas-source molecular-beam epitaxy, we obtained a device-quality GaInP epitaxial layer lattice matched to (100)-GaAs substrates, with a photoluminescence efficiency comparable to that of a crystal grown by liquid-phase epitaxy. A GaInP/AlInP double heterostructure laser with a GaInP active layer was fabricated, and pulsed lasing operation was achieved at room temperature for, we believe, the first time.

Energy Technology Data Exchange (ETDEWEB)

The aim of this document is to make a state-of-the-art of the techniques of heating-cooling ceilings and cold beams. These systems offer many advantages: they generate a high quality thermal comfort, they are energy efficient, and offer important room saving, particularly interesting in the case of building renovation. The document comprises 5 parts dealing with: 1 - the heating-cooling ceilings; 2 - the cold beams; 3 - the elements necessary for the dimensioning (building-system interactions, ventilation, temperature regulation and safety systems); 4 - dimensioning method; 5 - design, realization and operation: the rules to follow. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

A high heating value, fuel pellet comprises from about 50 to about 99% by weight natural cellulosic material and from about 1 to about 50% by weight synthetic polymeric thermoplastic material. The synthetic thermoplastic material is uniformly distributed throughout the fuel pellet. The thermoplastic material is solid at room temperature and has an injection molding temperature of at least 200/sup 0/F. Such a fuel pellet can be prepared in a pelletizer where the temperature of the pellet as it emerges from the die is from about 150 to about 250/sup 0/F.

Energy Technology Data Exchange (ETDEWEB)

Thermal expansions of a simulated fuel (SS-1) were measured by using a Dilatometer (DIL402C) from room temperature to 1900 K. The main procedure of an uncertainty evaluation followed the strategy of the UO{sub 2} fuel. Referring to the ISO (International Organization for Standardization) guide, the uncertainties of the thermal expansion were quantified in three parts - the initial length, the length variation, and the system calibration factor. The uncertainty of the thermal expansion for a simulated fuel was also compared with those of UO{sub 2} fuel.

Energy Technology Data Exchange (ETDEWEB)

Periureteral or subtrigonal injection of dextranomer/hyaluronic acid (Dx/HA) copolymer (Deflux, Q-Med, Uppsala, Sweden) is an increasingly common endoscopic treatment for vesicoureteral reflux. We report a confusing radiographic finding of bilateral calcified Dx/HA injections initially thought to represent bilateral distal ureteral stones in a boy who presented with intermittent periumbilical pain. Urologists, radiologists, and emergency room physicians should be aware of the potential for calcification of ureteral implants of Dx/HA, and of the potentially confusing radiographic images that may result. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Magnesium cast parts as well as indirectly and hydrostatically extruded profiles were used in order to investigate the influence of different microstructures on the damping behaviour of magnesium AZ-alloys. Especially, hydrostatic extrusion leads to a significant grain refinement in the extruded profile compared to indirect extrusion. Strain dependent damping measurements were carried out at room temperature using alloys AZ31, AZ61 and AZ80. Damping was determined as the logarithmic decrement of free bending beam vibrations. The results of these measurements after indirect and hydrostatic extrusion are shown and discussed. (orig.)

International Nuclear Information System (INIS)

The compressive and torsional buckling behavior of carbon nanotube bundles at room temperature is examined with classical molecular dynamics simulation. The critical compressive load and stiffness of a single carbon nanotube in the bundle are found to be similar to those of individual carbon nanotubes. However, the critical torsional moment and stiffness of a single carbon nanotube in the bundle are found to be higher than those of individual carbon nanotubes. In addition, this study demonstrates that van der Waals interactions between the nanotubes in the bundle significantly affect the critical compressive load of the nanotube bundle.

Energy Technology Data Exchange (ETDEWEB)

Adsorption of phosphate (PO{sub 4}{sup 3{minus}}) from aqueous solution on activated red mud (ARM) was studied as a function of time, pH, temperature, concentration of adsorbent and adsorbate in acetic acid-sodium acetate buffer medium. The adsorption of phosphate follows Langmuir as well as Freundlich adsorption isotherms. The process efficiency was found to be 80--90% at room temperature. This can be extended to the treatment of industrial effluents containing phosphates like that from phosphatic fertilizer plants.

Energy Technology Data Exchange (ETDEWEB)

The results of a scoping study of onsite radiation exposures which could take place in each of three types of postulated reactor accidents are presented. The accident types are (1) a fuel handling accident at a Mark III BWR; an interfacing system LOCA or V sequence at a PWR; and and Anticipated Transient Without Scram (ATWS) at a Mark I BWR. Both external and internal dose pathways are considered. The results of the study indicate the prohibitively high radiation doses could be received in some plant areas if personnel were to remain there. However, times of the order of a few minutes to a few hours, depending on the type of accident, would be available before life-threatening doses would be accumulated assuming that the provided full face respiratory protection equipment were used promptly. Special attention was given radiation doses possibly received by control room personnel for several control room air in-leakage assumptions. For occupancy ...

Energy Technology Data Exchange (ETDEWEB)

Fourier transform infrared absorption spectroscopy has been used for the determination of the line strengths of 41 CO and CO[sub 2] absorption lines at temperatures between 295 and 1250 K. The CO vibrational-rotational lines were from the [ital P] branch of the fundamental absorption band (2150--1950 cm[sup [minus]1]) while the CO[sub 2] vibrational-rotational lines were from the far wing of the [ital R] branch of the [nu][sub 3] fundamental band (2395--2380 cm[sup [minus]1]). The intensities of the lines were measured from absorption spectra recorded in a high-temperature gas cell containing known concentrations of CO/CO[sub 2]/N[sub 2] gas mixtures at atmospheric pressure. Absorption spectra were recorded through the cell with the use of a moderate-resolution Fourier transform infrared spectrometer. The absorption spectra were mathematically corrected for distortions resulting from the finite resolution of the spectrometer and for peak overlap. Line strength measurements were made ...

International Nuclear Information System (INIS)

This paper describes a reactor design to facilitate a room-temperature nuclear fusion/fission reaction to generate heat without generating unwanted neutrons, gamma rays, tritium, or other radioactive products. The room-temperature fusion/fission reaction involves the sequential triggering of billions of single-molecule, "6LiD 'fusion energy pellets' distributed in lattices of a palladium ion accumulator that also acts as a catalyst to produce the molecules of "6LiD from a solution comprising D_2O, "6LiOD with D_2 gas bubbling through it. The D_2 gas is the source of the negative deuterium ions in the "6LiD molecules. The next step is to trigger a first nuclear fusion/fission reaction of some of the "6LiD molecules, according to the well-known nuclear reaction: "6Li + D #-># 2"4He + 22.4 MeV. The highly energetic alpha particles ("4He nuclei) generated by this nuclear reaction within the palladium will cause shock and vibrations in the ...

Energy Technology Data Exchange (ETDEWEB)

The ventilation performance of cold-air distribution systems was investigated in a full-scale test room for three different designs of ceiling-mounted diffusers: a large square radial, a small square radial, and two linear diffusers. The supply air temperature was 38 F (3.3 C). Tests were conducted with internal heat loads and with and without furnishings. The local mean ages of air, air diffusion effectiveness, and contaminant-removal efficiency were measured using tracer gas techniques to assess the performance of the ventilation system in maintaining adequate air quality conditions in the occupied region. Air velocities and temperatures were also measured in the occupied region to calculate the air diffusion performance index (ADPI). It was found that the cold-air distribution system provided satisfactory air quality and thermal comfort conditions to the occupied region of the room. It was also found that internal furnishings (partitions, ...

International Nuclear Information System (INIS)

In this study, radon-222 in indoor air was surveyed in 62 rooms located in four governmental schools, for girls, in Tarqumia town that lies in the north western part of Hebron city in Palestine. The annual effective dose equivalents resulting from the inhalation of radon and its daughters by 2318 pupils and 102 staff members occupying the surveyed rooms were also measured. TASTRAK, a solid state nuclear track detector, has been used to measure the indoor radon concentrations at those schools thus, 124 radon detectors were distributed in the four school buildings. The radon detectors stayed for 70 days between February 2006 and April 2006. The results showed that the radon concentration and the annual effective dose equivalent in these schools were varied from 12 to 232.5 Bq/m"3 with an average of 34.1 Bq/m"3 and 0.62 to 12.0 mSv/y with an average of 1.76 mSv/y, respectively. The mean values of radon concentrations in Tarqumia secondary girls ...

Energy Technology Data Exchange (ETDEWEB)

Acceptance Testing of the WRAP 1 Plant Control System Hardware will be conducted throughout the construction of WRAP I with the final testing on the Process Area hardware being completed in November 1996. The hardware tests will be broken out by the following functional areas; Local Control Units, Operator Control Stations in the WRAP Control Room, DMS Server, PCS Server, Operator Interface Units, printers, DNS terminals, WRAP Local Area Network/Communications, and bar code equipment. This document will contain completed copies of each of the hardware tests along with the applicable test logs and completed test exception reports.

Science.gov (United States)

Put in place to protect the rights of the child, the Convention on the Rights of the Child is a set of non-negotiable standards. A core principle underpinning the Convention is the child's right to participate fully in social arenas and to access sources of social support without excessive interference. Juxtaposing this is the right of the child to be shielded from harm, abuse and exploitation. Over the past several decades the Internet has emerged as a fast and easily accessible medium for people to connect and communicate. While the Internet provides children with a source of support through chat rooms, online communities and social networking sites, just as equally it can expose vulnerable children to predatory and deviant individuals exacerbating the potential for harm. Upholding the Convention in cyberspace is a challenge. The Internet is not owned or regulated by any governing body and accountability is difficult to enforce. This article discusses some of the ...

Science.gov (United States)

The focus of the May-June issue is on training and information technology. Major articles/reports in this issue include: Communicating effectively, by Alain Bucaille, AREVA; Reputation management, by Susan Brisset, Bruce Power; Contol room and HSI modernization guidance, by Joseph Naser, EPRI; How far are we from public acceptance, by Jennifer A. Biedscheid and Murthy Devarakonda, Washington TRU Solutions LLC; Spent fuel management options, by Brent W. Dixon and Steven J. Piet, Idaho National Laboratory; Industry Awards; A secure energy future for America, by George W. Bush, President, United States of America; Vision of the future of nuclear energy, by Anne Lauvergeon, AREVA; and, Plant profile: strategy for transition to digital, TXU Power.

British Library Electronic Table of Contents (United Kingdom)

A testing methodology, which includes the evaluation of free sintering strain, stress-induced dimensional changes, and weight changes, was developed to determine the critical dimensional changes and thermomechanical response during presintering (i.e., before densification). The effects of organic binder burnout, decomposition of phases, and phase changes on the thermomechanical behavior of a ceramic green body, consisting of methylcellulose as a binder, gibbsite, silica, and alumina, were studied. The compressive stress-strain behavior was found to be nonlinear. The average compressive and tensile strengths of the sample at room temperature were -14.5 and 1.06 MPa, respectively. Both the compressive and tensile strengths decrease by two orders of magnitude with the increasing temperature a...

International Nuclear Information System (INIS)

The complex thermally stimulated luminescence (TSL) pattern of NaAlSi_3O_8 has been analyzed on transparent and opaque varieties of natural crystals and synthetic pure powder. The existence of seven additional peaks in the range 20 to 450 "0C following X-irradiation at room temperature (RT) is reported, also evaluated by the curve fitting method. The validity of the analysis is discussed in the light of detailed trap analysis of KAlSi_3O_8. An attempt has been made to probe the excistence of high temperature peaks beyond 450 "0C using UV stimulation at RT. All the TSL peaks analyzed follow a second-order kinetic process.

British Library Electronic Table of Contents (United Kingdom)

In this study polycrystalline specimens of as-cast DyCu with B2 crystal structure were compressed to different strains at room temperature to test if stress-induced phase transformation and twinning occur during deformation. In these tests DyCu exhibited high ductility with plastic strain as high as 35% and ultimate compressive strength of ~790MPa. X-ray diffraction and transmission electron microscopy (TEM) showed no indications that DyCu had undergone stress-induced phase transformation or twinning. -type dislocations have been observed to play an important role for imparting the ductile behavior. TEM analyses showed the presence of second phases, Dy2O3 and DyCu2 within the DyCu. The mechanisms of ductility and impurity phase formation are discussed.

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are compared.

British Library Electronic Table of Contents (United Kingdom)

A new low molecular mass organogelator 1 containing 2-(2prime-hydroxyphenyl)benzoxazole (HPB) group with long alkyl chain was synthesized by the reaction with 5-amino-2-(2prime-hydroxy-4prime-methylphenyl)benzoxazole and dodecyl isocyanate in THF at room temperature. The reversible gelation ability of 1 was investigated using a heating-cooling method in various organic solvents. The stable organogel was formed from carbon tetrachloride or from cyclohexane at the concentration as low as 0.9%. The self-assembled supramolecular gel structure formed by non-covalent bonding was confirmed with field emission-scanning electron microscope (FE-SEM) exhibiting fibril- or ribbon-shaped structure depending on the solvent used. Regarding the aggregation-induced emission enhancement (AIEE) phenomenon, t...

Science.gov (United States)

Current medical visualization technology intended for positional guidance in surgical applications may only ever have limited utility in the operating room due to the preexisting visual requirements of surgical practice. Additionally, visual systems impose limits as a result of their high latency, poor image resolution, problems with stereopsis and physical strain upon the user. Audio technology is relatively unexamined in the broad range of available methodologies for medical devices. The potential to translate surgical instrument position into audio feedback presents a novel solution to the human factors and engineering problems faced by visual display technology because audio technology employs a rich and as yet unburdened sensory modality. We describe an experimental system we have developed for investigating this new interface design approach using commercially available hardware. PMID:10173065

British Library Electronic Table of Contents (United Kingdom)

Based on the corrected phase diagrams proper growth conditions for Li2Zn2(MoO4)3 crystals are selected. Large crystals (up to 100 mm), both impurity-free and activated by transition metal ions (Cu, Cr), are grown by the low-gradient Czochralski method. By the EPR method the charge state and structural position of copper and chromium ions are determined. The performed studies of luminescent properties show that for impurity-free crystals luminescence with ? = 388 nm with a two-exponential luminescence decay with ?1 = 2 ns and ?2 = 6 ns is observed at room temperature. At 77 K for both impurity-free crystals and those activated with transition metal ions luminescence with ? = 560 nm and the luminescence lifetime ? = 100 ns is observed, the intensity of luminescence with ? = 560 nm depending ...

Energy Technology Data Exchange (ETDEWEB)

Facility management has long been regarded as a cost reduction measure, but it is also a means of raising the financial worth of a building so that landlords can get higher rents or sell the building at a better price. [German] Lange Zeit wurde Facility Management als eine Massnahme zur Kostensenkung angesehen. Heutzutage zeigt sich immer mehr, dass das Facility Management sehr viel umfassender zu verstehen ist: Der Wert eines Gebaeudes bemisst sich nicht allein an einer niedrigen Kostenquote, sondern er soll umfassend Investoren wie Mietern den hoechst moeglichen Nutzen bringen. Nicht allein der kostenguenstige Betrieb ist entscheidend, sondern der Wert des Gebaeudes muss insgesamt gesteigert werden. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We have studied, by a Monte Carlo simulation code ACAT-DIFFUSE, the fluence-dependence of the amount of retained helium atoms in tungsten carbide at room temperature under helium ion bombardment. The retention behavior may be understood qualitatively in terms of irradiation-dependent diffusion coefficient assumed and range. The emission processes from tungsten carbide under helium ion irradiation derived were compared with each other. We have discussed the retention curves for incident energy of 5 keV at incident angles of 0deg and 80deg and of 500 eV at 0deg. The energy spectra of helium atoms reflected from tungsten carbide for incident energy of 500 eV at 0deg and 80deg were compared with those from graphite and tungsten. (author)

International Nuclear Information System (INIS)

Paraquat is a nonselective contact herbicide of great toxicological importance, being associated with high mortality rates, mainly due to respiratory failure. We report the case of a 22-year-old male admitted to the emergency room with a sore throat, dysphagia, hemoptysis, and retrosternal pain after the ingestion of 50 mL of a paraquat solution, four days prior to admission. Chest CT scans revealed pulmonary opacities, pneumomediastinum, pneumothorax, and subcutaneous emphysema. The patient was submitted to two cycles of immunosuppressive therapy with cyclophosphamide, methylprednisolone, and dexamethasone. The pulmonary gas exchange parameters gradually improved, and the patient was discharged four weeks later. The clinical and tomographic follow-up evaluations performed at four months after discharge showed that there had been further clinical improvement. We also present a brief review of the literature, as well as a discussion of the therapeutic algorithm for ...

British Library Electronic Table of Contents (United Kingdom)

With the advent of computer technology, researchers and instructors are attempting to devise computer support for effective collaborative technical writing. In this study, a computer-supported environment for collaborative technical writing was developed. This system (Process-Writing Wizard) provides process-oriented scaffolds and a synchronous online chat room to facilitate real-time collaborative writing practice. It allows multiple students to work synchronously on collaborative writing tasks via the Internet. It also helps develop collaborative writing strategies, such as creating team agendas, brainstorming, creating team outlines, and generating team articles. An experiment was conducted to examine the effect of the system on EFL (English as a Foreign Language) students? collaborativ...

International Nuclear Information System (INIS)

Defect cluster formation in 14-MeV neutron irradiated polycrystalline copper has been observed by transmission electron microscopy (TEM) and correlated with the increase in yield stress. The measurements indicate that the radiation hardening component of the yield strength in polycrystals is not directly additive to the unirradiated yield strength. A transitional behavior was observed for radiation hardening at low fluences, which produces an anomalous variation of the defect cluster barrier strength with fluence. The behavior is attributed to the effect of grain boundaries on slip band transmission. An upper limit for the room temperature barrier strength of defect clusters in neutron-irradiated copper was determined to be #alpha#=0.23. (orig.).

International Nuclear Information System (INIS)

The whole equipment consists of three separate portable parts: a detector case, a microprocessor and a graphic TV monitor. Magnetic tape memory and an x-y recorder can be connected for recording the measured spectra. The analyzer contains two built-in exchangeable excitation radionuclides. Fluorescence and scattered radiation is detected using a proportional detector. The detected pulses are analyzed by a 256-channel analyzer and the results are shown on the display. The device may be used in mining laboratories, coal and ore dressing plant control rooms or in mining fields of open cast mines for quick detection of the quality of mined or dressed raw materials. (E.S.). 1 fig.

British Library Electronic Table of Contents (United Kingdom)

Zeaxanthin is a carotenoid produced by plants and has been associated with protection of the photosynthetic machinery under light stress and, together with lutein, in protection of the central retina of the eye. Zeaxanthin levels in blood plasma have been negatively correlated to the development of AMD (age-related macular degeneration) (Gale et al., 2003). Under normal conditions, plants have a low content of zeaxanthin. The aim of this study was to increase the zeaxanthin content in green vegetables by post harvest treatments. Efficient conditions for activation of the endogenous enzyme system generating zeaxanthin was established and included incubation at low pH (2.5-5.5), with the membrane permeable acetic acid/acetate buffer at room temperature or above for 30min or more. Typically m...

British Library Electronic Table of Contents (United Kingdom)

This work deals with a new route to modify polymer blend morphology in order to improve the porosity of gas diffusion layers (GDLs) for proton exchange membrane fuel cells (PEMFCs). First, electrically conductive polymer-based blends were carefully formulated using a twin-screw extrusion process. Blend electrical conductivity was ensured by the addition of high specific surface area carbon black and synthetic graphite flakes. Final GDL porosity, in particular its macroporosity, was generated by melt blending polyamide 11 (PA11) matrix with polystyrene (PS) followed by PS extraction with tetrahydrofuran (THF) solvent at room temperature. In order to improve GDL porosity by the optimisation of PS dispersion in the PA11 matrix, PA11/PS blends were compatibilised by the addition of 2 wt.-% of ...

International Nuclear Information System (INIS)

In this paper a novel method is presented, based on the use of plasma processing, to suppress the transient enhanced diffusion of boron implanted in silicon. We found for silicon samples processed with plasma and subsequently boron implanted that the anomalous diffusion of the dopant atoms at the beginning of the annealing process is almost completely suppressed. This phenomenon is interpreted in terms of capture of the ion beam generated interstitials by the dislocations induced by the plasma processing. At room temperature the dislocations are observed to grow in size after the boron implant, attesting their efficiency as trapping centres for interstitials. Moreover, varying the plasma process conditions we can establish a general relation between the presence of the trapping centres induced by the plasma processing and the suppression of the transient diffusion.

Science.gov (United States)

Homogenous Al{sub x}Ga{sub 1{minus}x}P liquid phase epitaxial layers have been obtained with the temperature difference method under controlled vapor pressure (TDM-CVP). Very clear fine structures near band edge in photoluminescence spectra have been observed at 77 K for the first time. Photoluminescence measurement results confirmed that the free exciton recombination without phonon assistance plays an important role in the luminescence at 77 K and becomes dominant at room temperature. It is considered that Zero-phonon assisted free exciton recombination is intensified by some local perturbations to electrical potentials against carriers or excitons introduced by Al atoms in Al{sub x}Ga{sub 1{minus}x}P layers, which can give momentum change necessary for recombination.

British Library Electronic Table of Contents (United Kingdom)

Pectin rich cold stored spoiled fruits, vegetables and cold soils were screened and different pectinolytic isolates were obtained by enrichment culturing and ruthenium red plate assay. Among the primary isolates 10-15% were yeast isolates. Six isolates with higher zones of pectin hydrolysis were selected and tested for polygalacturonase (PGU) production at room temperature (25 degrees C) and at 5 degrees C. One isolate identified as Saccharomyces sp. with highest polygalacturonase activity at 5 degrees C was used for enzyme production using raw fruit pectins as substrates. The isolate was identified by preliminary cultural, morphological and sugar fermentation tests. PGU production was high in raw pectin substrates like orange peel (21 U/ml), apple peel (20 U/ml ), mango peel (19 U/ml), ...

International Nuclear Information System (INIS)

Upon irradiation of aqueous ethylene glycol/water solutions of native chloroperoxidase (CPO) with "6"0Co-gamma rays at 77K one observes the one-electron reduction of the enzyme active site by radiolytically generated thermolyzed electrons. In the present study the first absorption spectrum of a low-spin ferrous form of CPO is reported which has peaks at 438, 532 and 563 nm, similar to those observed previously for cytochrome P-450. All previously described ferrous forms of CPO are high spin. In order to observe the final results of the CPO reaction with electrons, the spectral changes of native enzyme after room temperature-gamma-irradiation have also been investigated. Evidence of changes is also presented probably connected with disruption of the tertiary structure of enzyme, correlated with decrease of enzyme activity.

Energy Technology Data Exchange (ETDEWEB)

In the spring of 1991, the Environmental Protection Agency, Region 10 (EPA), launched an investigation into tanker waste disposal practices for vessels discharging ballast water at the Alyeska Pipeline Services Company's Ballast Water Treatment (BWT) facility and marine terminal in Valdez, Alaska. It had been alleged that the Exxon Shipping Company was transferring 'toxic wastes originating in California' to Valdez. In response, EPA decided to examine all waste streams generated on board and determine what the fate of these wastes were in addition to investigating the Exxon specific charges. An extensive Information Request was generated and sent to the shipping companies that operate vessels transporting Alaska North Slope Crude. Findings included information on cargo and fuel tank washings, cleaning agents, and engine room waste.

Energy Technology Data Exchange (ETDEWEB)

The growth of thin Pd[sub 2]Si films on Si(111) surfaces is studied using [ital in] [ital situ] transmission electron microscope under ultrahigh vacuum conditions. No immediate reaction of deposited Pd with Si is observed at room temperature. At [similar to]200 [degree]C, uniform Pd[sub 2]Si films can be formed. The thin Pd[sub 2]Si films are found to grow into strained islands at elevated temperatures. Interfacial misfit dislocations associated with interfacial steps propagate across the strained islands, causing the islands to grow layer-by-layer at the interface. The strain fields associated with the misfit dislocations are believed to be responsible for this behavior.

Energy Technology Data Exchange (ETDEWEB)

Sulfuric acid hydrogen peroxide mixtures (SPM) are commonly used in the semiconductor industry to remove organic contaminants from wafer surfaces. This viscous solution is very difficult to rinse off wafer surfaces. Various rinsing conditions were tested and the resulting residual contamination on the wafer surface was measured. The addition of small amounts of a chemical base such as ammonium hydroxide to the rinse water has been found to be effective in reducing the surface concentration of sulfur and also mitigates the particle growth that occurs on SPM cleaned wafers. The volume of room temperature water required to rinse these wafers is also significantly reduced.

International Nuclear Information System (INIS)

The present work is a research of the effect of helium on the microstructure, mechanical properties and fracture behaviors of a type 316 austenitic steel. Helium implantation was performed by 30-MeV #alpha#-particle injection on very small size specimens, using a cyclotron. Average helium content in a He-deposited region was up to 2000 appm He. In the case of 2000appm He implantation, intergranular fracture was sometimes observed on the helium deposited region after tensile test at room temperature. At elevated temperature test, however, this material showed the transition of fracture mode from transgranular-ductile fracture at 773K to intergranular fracture at 873. In the case of 500 appm He implantation, the transition of fracture mode was recognized at a temperature range of 873K to 973K. (author).

Energy Technology Data Exchange (ETDEWEB)

A method for determining the mobility of hydrogen as a function of temperature in superconducting niobium cavities comprising: 1) heating a cavity under test to remove free hydrogen; 2) introducing hydrogen-3 gas into the cavity; 3) cooling the cavity to allow absorption of hydrogen-3; and 4) measuring the amount of hydrogen-3 by: a) cooling the cavity to about 4.degree. K while flowing a known and regulated amount of inert carrier gas such as argon or helium into the cavity; b) allowing the cavity to warm at a stable rate from 4.degree. K to room temperature as it leaves the chamber; and c) directing the exit gas to an ion chamber radiation detector.

British Library Electronic Table of Contents (United Kingdom)

Magnetic properties of Fe-Co-Mo-Cu-B alloy system with Co up to 26at.% were investigated. After proper thermal treatment, the nanocrystalline grain remains tiny, the density hardly increases, but the room-temperature saturation attains 1.5T mainly due to a high enough Curie temperature. The generally observed slant hysteresis loops point to ribbon surfaces, which stress the ribbon interior and induce a specific magnetoelastic contribution to hard-ribbon-axis magnetic anisotropy even after vacuum annealing. The effect does not come from cobalt but rather from the lack of silicon. Partial removal of the surfaces resulted in a decrease of the loop tilt.

International Nuclear Information System (INIS)

We present two cases of fetal neck masses that were initially diagnosed by ultrasound and further evaluated with prenatal MRI. MRI findings aided in further delineating the neck masses, increasing confidence in the final diagnosis (cervical teratoma and cystic hygroma). With the fetal airway typically filled with fluid that is of high signal on T2-weighted sequences, MRI images in three planes could identify whether the fetal larynx and trachea were partially or completely compressed by the neck tumor. This information was particularly useful in determining if a controlled delivery such as ex utero intrapartum treatment (EXIT) was necessary and aided the surgeons in planning their approach to establishing airway control in the delivery room. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: The Nuclear Power Plants (NPPs) are always designed for the highest level of safety against postulated accidents which may be initiated due to internal or external causes. One of the external/internal causes, which may lead to accident in the reactor and its associated systems, is fire in certain vital areas of the plant. Conventionally, the fire containment approach and/or the fire confinement approach is used in designing the fire protection systems of NPPs. Indian NPPs (PHWRs) follow the combined approach to ensure plant safety and all newly designed plants are required to comply with the provisions of Atomic Energy Regulatory Board (AERB) fire safety Guide. In respect of older plants, the reassessment of adequacy of fire safety provisions in the light of current advances has becomes essential so as to decide upon the steps for retrofitting. Keeping this in mind the deterministic fire hazard analysis was carried out for the Madras Atomic Power ...

International Nuclear Information System (INIS)

Nickel ion radiation at 500 C was shown to have a strong effect on the surface electrochemistry and intergranular corrosion (IGC) of stainless steel (SS). Measured current densities in a 1 N sulfuric acid solution at room temperature were increased at active-passive, passive, and transpassive potentials. Radiation effects on the current decay behavior and susecptibility to IGC were similar for a fine-grained (FG) S alloy and for a very large-grained (LG) SS. Radiation-induced segregation (RIS) at the surface was believed to promote higher currents at short times, whereas segregation at grain boundaries was responsible for IG attack. Analytical electron microscopy (AEM) measurements revealed chromium and iron depletion plus Ni and silicon enrichment at grain boundaries in irradiated specimens. Si enhanced dissolution at transpassive potentials, whereas Cr depletion did the same at active-passive and passive potentials.

Energy Technology Data Exchange (ETDEWEB)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10{sup -6} S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

International Nuclear Information System (INIS)

Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.

International Nuclear Information System (INIS)

The Moessbauer emission spectrum of "2"4"1Am metal was investigated for influences of radiation self damage. Samples were kept continuously for 230 h at 4.2 K and spectra were taken each 10 to 20 h. No change in f-factor was observed, while the linewidth increased monotonically and reached saturation after approximately 180 h. The original width could be reproduced by a brief warming to room temperature. The increase in width reflects the change in quadrupole interaction due to the creation of lattice defects. The constancy of the f-factor indicates that the basic crystalline structure is retained.

British Library Electronic Table of Contents (United Kingdom)

The tribological properties of gas pressure sintered SiAlON and its composite with 18wt% silicon carbide (SiC) against two different mating materials, i.e., alumina and SiAlON are evaluated. SiAlON and SiAlON-18%SiC composite ceramics were prepared by pressure less sintering and gas pressure sintering. Fretting wear tests were carried out under dry unlubricated ambient conditions (room temperature 23-25^oC; relative humidity 50-55%) with a load of 8N for 45,000 cycles. Friction and wear properties of SiAlON-SiC proved better than the monolithic SiAlON. The formation of silica roll like structure on the composite worn surface was observed.

Energy Technology Data Exchange (ETDEWEB)

The national energy research programme LVIS-2000: Future Building Services is concerned with the control of energy use and indoor climate in buildings of the future. The projects were presented at a one day seminar arranged by the Laboratory of Heating and Ventilation of the Technical Research Centre in Finland which is coordinating the programme. The presentations at the seminar were: Impurity emission from materials, Building materials and indoor air quality, analysis of organic compounds in indoor air, effect of the return air, effect of the return air on health and comfort, electric heating as an indoor climate factor, calculations of air flows in ventilated rooms, effect of energy saving measures on hospital hygiene, application of modern aerosol measurement technique on indoor climate research.

British Library Electronic Table of Contents (United Kingdom)

Commercial rolled magnesium sheets of alloys AZ31 (Mg-3 mass%Al-1 mass%Zn) and ZE10 (Mg-1 mass% Zn-<1 mass% Rare Earths) in O-temper condition were used for blanking experiments near room temperature. A serrated fracture surface can be observed in case of AZ31 but not in case of ZE10. During the shearing process of the AZ31 sheet, many micro cracks parallel to the sheet plane are generated in the shearing zone. These micro cracks lead to the formation of loose particles during the shearing operation, which interfere with further processing of the part and incur additional costs by increasing the scrap rate. It is found that the strong basal texture of this alloy is an important reason for the generation of such serrated cracks. In this paper a new method of selective texture modification i...

Science.gov (United States)

Data are presented on the continuous-wave (cw), room-temperature (300 K) operation of stripe-geometry In{sub 0.5}(Al{sub {ital x}}Ga{sub 1{minus}{ital x}}){sub 0.5}P quantum-well heterostructure lasers defined via hydrogenation. Passivation of the Zn acceptors in the cap and upper confining layer provides gain guiding, and elimination of the current-blocking oxide reduces the thermal impedance. The resultant device is capable of better performance than conventional oxide-stripe diodes fabricated on the same material.

International Nuclear Information System (INIS)

In this paper it will be discussed how to most effectively give room to competitive forces in natural gas markets, given the traditional merchant pipeline as point of departure. Alternative models of organizing the market will be reviewed: we first consider decreasing barriers to entry and then analyse advantages and drawbacks of a third party access system. In this context different forms of implementing a competitive market for transportation capacity and coordinating it with gas trade are discussed, among them a simultaneous auction of gas and transmission capacity. Finally a hub system of point markets will be suggested to improve the currently implemented third party access system and to allow for competitive markets for gas and transportation service. 33 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

Structural silicides have important high temperature applications in oxidizing and aggressive environments. Most prominent are MoSi{sub 2}-based materials, which are borderline ceramic-intermetallic compounds. MoSi{sub 2} single crystals exhibit macroscopic compressive ductility at temperatures below room temperature in some orientations. Polycrystalline MoSi{sub 2} possesses elevated temperature creep behavior which is highly sensitive to grain size. MoSi{sub 2}-Si{sub 3}N{sub 4} composites show an important combination of oxidation resistance, creep resistance, and low temperature fracture toughness. Current potential applications of MoSi{sub 2}-based materials include furnace heating elements, molten metal lances, industrial gas burners, aerospace turbine engine components, diesel engine glow plugs, and materials for glass processing.

Energy Technology Data Exchange (ETDEWEB)

The physics and technological issues involved in high gradient particle acceleration at high microwave (RF) frequencies are under study at MIT. The 17 GHz photocathode RF gun has a 1 1/2 cell ({pi} mode) room temperature cooper cavity. High power tests have been conducted at 5-10 MW levels with 100 ns pulses. A maximum surface electric field of 250 MV/m was achieved. This corresponds to an average on-axis gradient of 150 MeV/m. The gradient was also verified by a preliminary electron beam energy measurement. Even high gradients are expected in our next cavity design.

British Library Electronic Table of Contents (United Kingdom)

Purpose - This paper seeks to study how the democratization of the diffusion of research through the internet could have helped non-traditional fields of research. Design/methodology/approach - The specific case the authors approach is heterodox economics as its pre-prints are disseminated through NEP, the e-mail alert service of RePEc. Findings - Comparing heterodox and mainstream papers, the authors find that the heterodox are quite systematically more downloaded, and particularly so when considering downloads per subscriber. Research limitations/implications - The authors conclude that the internet definitely helps heterodox research, also because other researchers get exposed to it. But there is still room for more participation by heterodox researchers. Originality/value - The paper s...

Energy Technology Data Exchange (ETDEWEB)

Mechanical ventilation in private homes was for many years a stepchild of air conditioning engineers. A decisive impulse for change came in January 1995 with the enactment of the new Thermal Insulation Ordinance which for the first time allows house owners to exceed the usual admissible annual heating requirement by a certain amount on the condition that they equip the house with mechanical ventilation systems. (orig.) [Deutsch] Ueber lange Jahre war die mechanische Wohnungslueftung ein Stiefkind der Raumlufttechnik. Einen entscheidenden Impuls gab erst die seit Januar 1995 gueltige Waermeschutzverordnung, die erstmals zulaesst, dass ein gewisses Quantum des Jahres-Heizwaermebedarfs durch den Einbau mechanischer Wohnungslueftungen kompensiert werden kann. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Growth mechanisms and thermal stability of ion-beam-induced epitaxial Pd/sub 2/Si films are investigated using Rutherford backscattering and channelling techniques. Epitaxial growth of Pd/sub 2/Si films was observed at room temperature by argon ion implantation into as-deposited Pd/Si(111) structures and furnace-annealed Pd/sub 2/Si(polycrystalline)/Pd/sub 2/Si(epitaxial)/Si(111) structures. Some additional experiments to check the growth mechanisms are also presented, in which the implantation energies, substrate orientations and dose rates were changed. Finally, the stability of the ion-beam-induced epitaxial Pd/sub 2/Si films on subsequent furnace annealing is studied.

International Nuclear Information System (INIS)

Nanocrystalline powders of GaN with grain sizes ranging from 2 to 30 nm were examined under high external pressures by in situ diffraction techniques in a diamond anvil cell at DESY (HASYLAB, Station F3). The experiments on densification of pure powders under high pressure were performed without a pressure medium. The mechanism of generation and relaxation of internal strains and their distribution in nanoparticles was deduced from Bragg reflections recorded in situ under high pressures at room temperature. The microstrain was calculated from the full-width at half-maximum (FWHM) values of the Bragg lines. It was found that microstrains in GaN crystallites are generated and subsequently relaxed by two mechanisms: generation of stacking faults and change of the size and shape of the grains occurring under external stress. (author)

Energy Technology Data Exchange (ETDEWEB)

In parking areas of large extent, the removal of engine exhaust gases, especially of their CO gas components with ventilation plant is mainly done by transverse ventilation over short paths. By their presence, the ventilation ducts required for this purpose often reduce the value of the parking space by restrictions with a consequent reduction of their acceptance by the users. Longitudinal ventilation without ducts can be a remedy in such cases. Depending on the required room air quality in the zones of highest loading, the volume flows with longitudinal removal are no greater than with conventional transverse ventilation. This article is concerned with the different methods of operation of the two systems. (orig./BWI)

International Nuclear Information System (INIS)

A stable chlorobenzene dispersion of conducting polyaniline (PANI) has been obtained by doping emeraldine base with dodecylbenzene sulfonic acid (DBSA) and studied by spectrophotometric measurements in the UV-vis-IR range. The electrical properties of PANI: DBSA films obtained from the above dispersion have been investigated under different temperature and relative humidity conditions. All-organic chemoresistive devices have been developed by spin-coating the PANI: DBSA dispersion on flexible substrates, and then by depositing electrodes on the top, from a carbon nanotube conducting ink. Sensing tests performed under exposition to calibrated amounts of ammonia reveal that these simple and inexpensive sensors are able to detect ammonia at room temperature in a reliable way, with a sensitivity linearly related to concentration in the range between 5 ppm and 70 ppm.

Energy Technology Data Exchange (ETDEWEB)

It is very important to develop the design guidelines which can be applicable for Korean operators for the purpose of designing the KSNP more safely. The objective of this project is to provide the standards, guidelines and bases applicable for HF-010 through the within-subject experiment for obtaining Korean operators' population stereotype for direction-of-movement of controls associated with displays on the control panels. Through the survey of researches on display compatibility and the classification of types of displays and controls in the main control room of Uljin units 3 and 4, methods for an experiment on the stereotype were established. Experimental interface prototypes for a total of 108 combinations of display and control types were implemented. Experimental data collection and analysis system was built in association with the interface prototypes. The experiment was performed with participation of 250 students as subjects. About 20 guideline ...

British Library Electronic Table of Contents (United Kingdom)

Differential Scanning Calorimetry (DSC) is employed to study the changes in enthalpy of natural rubber latex samples when heated under a controlled temperature program. It is found that the mass normalized areas of the DSC curves between room temperature and 170??C for different latex samples are inversely proportional to the dry rubber content (DRC) of the samples, measured following the weighing and drying method. The changes in total enthalpy of the samples in this temperature range are interpreted as due to the variations in the quantity of water present in the samples. The measurements have been repeated by diluting selected samples with known quantities of water, and it is found that the normalized areas of the DSC curves are directly proportional to the amount of water added to the ...

International Nuclear Information System (INIS)

Pearls change their color to grey by #gamma#-ray irradiation. Grey densities were determined from darkness of pearl nuclei and thickness of the pearl layers. The densities are independent of both diameters of nuclei and pearls. The fading rate increases with increasing storage temperature. The rate of fading for irradiated pearls is lower than that for natural blue pearls. Comparison of photomicrographs (x 12) for pearls irradiated and then stored at room temperature for about 6 years revealed that their surfaces are not substantially different from the surfaces of unirradiated cultured pearls, indicating that #gamma# irradiation hardly gives rise to deterioration. #gamma#-Ray irradiation is a technique for coloration of pearls. Irradiated blue pearls seem to have resistivity to fading and to deterioration of the surface, if pearls have been irradiated properly. (author).

International Nuclear Information System (INIS)

The absorption spectra of an unoriented single crystal of the title compound (1) have been measured at room and at low temperatures. Assuming a similar sequence of crystal field (CF) levels as for the previously analyzed Nd[N(SiMe_3)_2]_3 (2) a truncated CF splitting pattern is derived from the spectra obtained. The parameters of an empirical Hamiltonian are fitted to the energies of 71 levels to give an r.m.s. deviation of 24.2 cm"-"1. The parameters obtained are compared with those of 2 and Nd[N(SiMe_3)_2]_3(CNC_6H_1_1)_2 (3). The observed trends of CF parameters are consistent with the results of simple model calculations in the framework of the angular overlap model. (orig.)

International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

International Nuclear Information System (INIS)

In the paper results of the investigation on the effect of microstructure on room temperature tensile properties and fracture toughness of two-phase #alpha#+#beta# titanium alloy Ti-6Al-2Mo-2Cr have been presented. Microstructure has been varied by changes in the cooling rate from the solution treatment temperature and aging time and temperature. Mechanical properties examined show dependence on the treatment conditions, especially aging conditions. It has been attributed mainly to the amount and morphology of #alpha# phase obtained after heat treatment. The higher volume fraction of lamellar #alpha# structure, the higher fracture toughness. (author)

Energy Technology Data Exchange (ETDEWEB)

Investigations of dislocation structure and mechanical properties of iron after rolling deformation in shaped rolls and after hydroextrusion are conducted. It is shown that dislocation iron structure slightly changes with deformation degree after rolling in shaped rolls and annealing and it is characterized by low density of screw dislocations. Cold brittleness temperature decreases in the result of rolling and the succeeding recrystallization and impact strength increases both at room temperature and at low temperatures. Screw dislocations having high Peierls barrier prevail in the structure after hydroextrusions. The iron deformed by hydroextrusion at 400 mPa and higher after annealing has high cold brittleness temperature and low impact strength.

International Nuclear Information System (INIS)

We have investigated the diffusion of Sb in Si in the presence of defects injected by high-energy implantation of Si ions at room temperature. MeV ion implantation increases the concentrations of vacancies, which induce transient-enhanced diffusion of Sb deposited in Si. We observed a significant enhancement of Sb diffusion. Secondary ions mass spectroscopy has been performed on the implanted samples before and after annealing. Rutherford-backscattering spectrometry has been used to characterize the high-energy implantation damage. By fitting diffusion profiles to a linear diffusive model, information about atomic scale diffusion of Sb, i.e. the generation rate of mobile state Sb and its mean migration length were extracted.

International Nuclear Information System (INIS)

To study the nanoscale electronic order in strongly correlated electron systems and vortex states in high-Tc superconductors in high magnetic fields, we have developed scanning tunneling microscopy (STM) for the 18 T cryocooled superconducting magnet (18T-CSM). The test results of the STM operation in the 18T-CSM at room temperature indicate that our STM has a good atomic resolution up to 18 T when we use the nonmagnetic vibration-isolation table which reduce the vibration noise from the cryocoolers of the 18T-CSM. In this paper, we report on the design of the high-field STM system for large-scale magnets and its performance.

International Nuclear Information System (INIS)

The band offsets and subband levels in a double quantum well layer for a 660 nm-Ga_0_._4In_0_._6P/(Al_0_._5Ga_0_._5)_0_._5In_0_._5P quantum well laser are determined by photoreflectance using a 410 nm InGaN laser with current modulation at room temperature. The subband levels are analyzed by numerical calculation of the Schroedinger equation for the layer structure by varying the conduction band offset and compared with the measured photoreflectance spectra. The conduction band offset ratio is determined to be 0.5+0.03. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Science.gov (United States)

The decomposition of three ?-lactam antibiotics (amoxicillin, oxacillin and ampicillin) in aqueous solution was investigated using a dielectric barrier discharge (DBD) in coaxial configuration. Solutions of concentration 100 mg/L were made to flow as a film over the surface of the inner electrode of the plasma reactor, so the discharge was generated at the gas-liquid interface. The electrical discharge was operated in pulsed regime, at room temperature and atmospheric pressure, in oxygen. Amoxicillin was degraded after 10 min plasma treatment, while the other two antibiotics required about 30 min for decomposition. The evolution of the degradation process was continuously followed using liquid chromatography-mass spectrometry (LC-MS), total organic carbon (TOC) and chemical oxygen demand (COD) analyses. PMID:21514950

British Library Electronic Table of Contents (United Kingdom)

Abstract: Decomposition and insect colonization of pig (Sus scrofa L.) carcasses were observed over a 42 day period inside and outside a house in a suburban region of Edmonton, Alberta. Three freshly killed pig carcasses were placed outdoors on grass and three carcasses were placed in separate rooms inside a house in a suburban residential area. The carcasses were examined and sampled regularly. Outside carcasses were colonized rapidly by Calliphora vicina (R D), Lucilia sericata (Meigen), Lucilia illustris (Meigen), Eucalliphora latifrons (Hough), Cynomya cadaverina (R D), Phormia regina (Meigen), and Protophormia terraenovae (R D). There was a delay of 5 days before inside carcasses were first colonized but all species except E. latifrons and L. illustris readily colonized at this time. ...

Energy Technology Data Exchange (ETDEWEB)

In this, the last of a series of three papers, we discuss a method of forming iron phosphate ceramics by a reduction process. We report the formation of iron oxide ceramics by reducing hematite with iron in a phosphoric acid solution. The reaction results in a rapid-setting ceramic (at room temperature) with a compressive strength of 3700 psi and a density of 1.7 g/cm{sup 3}. Although the exact mineral form of the binder is difficult to determine because it is mostly amorphous and hence is not amenable to X-ray diffraction analyses, this material is expected to consist of iron hydrophosphates. The reduction process is very useful in recycling several industrial wastes that are rich in hematite, including iron mine tailings, red mud (a caustic waste from the alumina industry), and machining swarfs. Formation of ceramics with red mud and swarfs is also discussed.

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer conferring improved protection.

International Nuclear Information System (INIS)

Channeling effect measurements have been employed to investigate radiation damage produced by 100-keV Ar ions in preferred oriented polycrystalline metal-silicide layers, such as Pd_2Si and NiSi_2 layers formed on single-crystalline Si. For room-temperature implantation, an amount of the damage in Pd_2Si layers was found to saturate at doses between 3 x 10"1"4 and 1 x 10"1"7 ions/cm"2, where the minimum aligned yield of 1.5-MeV He ions was nearly 40% of the random one. On the contrary, it was observed that the NiSi_2 layers became amorphous at doses higher than 3 x 10"1"5 ions/cm"2. These results were confirmed by the reflection electron diffraction analyses.

Energy Technology Data Exchange (ETDEWEB)

Evaporated palladium films of 45 nm thickness on Si(111) were irradiated using 78 keV Ar/sup +/ ions with doses in the range of 1 x 10/sup 15/ to 1.5 x 10/sup 16/ cm/sup -2/ for the purpose of studying silicide formation. Rutherford backscattering analysis shows that intermixing has occurred across the Pd-Si interface at room temperature. The mixing behaviour increases with increasing dose of the bombarding ions, which agrees well with a theoretical model of isotropic cascade mixing for palladium, and radiation-enhanced diffusion associated with an interstitial mechanism for silicon.

Energy Technology Data Exchange (ETDEWEB)

An apparatus is described for measuring the total hemispherical emittance of pipes of a length suitable for use in a prototype solar collector. The calorimetric method used requires measurements of the temperatures of the surface of the test pipe and of a concentric outer cylinder and measurement of the electrical power used to heat the test pipe. Measurements were made of the total hemispherical emittance of black chrome, nickel, and bare steel pipes as a function of temperature. The emittance of the black chrome surfaces increased significantly from an extrapolated value of about 0.1 at 25 deg C to values on the order of 0.3-0.4 at 300 deg C. The extrapolated values for black chrome agreed with measurements made using other techniques at room temperature. The results for the nickel-plated pipe agreed with total emittance calculated from spectral reflectance data.

British Library Electronic Table of Contents (United Kingdom)

The interscalenic block technique is widely used for ambulatory shoulder surgery despite a substantial number of failures and adverse effects. We prospectively evaluated satisfaction in 40 consecutive patients who underwent open Bankart repair under a single general anesthesic performed in an ambulatory care unit. The mean age of the patients was 23 years. There were 29 men and 11 women. Patients were evaluated postoperatively with a visual analog scale of pain (in the recovery room, at the time of discharge, and the day after and 1 week after surgery) via a home assessment questionnaire that included the following: effectiveness of oral pain medication, ability to perform activities of daily life, and overall satisfaction. One patient failed to be discharged because of a feeling of faintn...

Science.gov (United States)

We report the characteristics of visible vertical cavity surface emitting laser diodes. Wafers are grown such that the Fabry--Perot resonance wavelength changes with position from 690 to 620 nm, overlapping to varying degrees with the [ital n]=1 and [ital n]=2 quantum well gain peaks at [similar to]670 and 650 nm. Gain guided devices are tested across the entire wafer, and pulsed room temperature lasing is observed from 634.6 to 663.2 nm. Our results suggest that gain contributions from the second quantized state are required to overcome high cavity losses in order to achieve lasing.

British Library Electronic Table of Contents (United Kingdom)

A novel liquid phase alkylation of aniline with methanol over Zn/Cu salts modified kaolin assisted with a pair of porous carbon electrode in slurry-bed reactor under constant current intensity, room temperature and atmospheric pressure was reported. The Zn/Cu salts modified kaolin catalysts were synthesized and characterized by infrared spectrometer (IR), powder X-ray diffraction (XRD) and scanning electron microscopy (SEM), which showed that the transition metals were completely supported on kaolins structure and formed a pored one. The effect parameters, such as initial pH, electrolysis time, metal ratio with kaolin and salts composition in this electrochemical catalytic system, were studied. The procedure was inspected by ultraviolet-visible spectrum (UV-vis), and the product distributi...

British Library Electronic Table of Contents (United Kingdom)

The monoanionic bidentate Schiff base, N-(phenolyl)-benzaldimine (HL), has been employed to synthesize a new vanadium(IV) complex of general composition [VO(L)2] (where L = O, N donor of Schiff base). The ligand and complex have been fully characterized by elemental analyses, molar conductance data, FT-IR, 1H- and 13C-NMR, and UV-Vis spectroscopies. Oxidation of alcohols to their corresponding aldehydes and ketones was conducted by this complex catalyst using Oxone as oxidant under biphasic reaction conditions (CH2Cl2/H2O) and tetra-n-butylammonium bromide as phase transfer agent under air at room temperature.

British Library Electronic Table of Contents (United Kingdom)

This paper presents a hybrid solar desalination process of the multi-effect humidification dehumidification and the basin-type unit. The sketch of the hybrid solar desalination process is given. The solar vacuated tube collector is employed in the desalination system, multi-effect humidification dehumidification desalination (HDD) process is plotted according to pinch technology, and then the water rejected from multi-effect HDD process is reused to desalinate in a basin-type unit further. The gain output ratio (GOR) of this system will rise by 2?3 at least through reusing the rejected water. The research proves that the multi-effect HDD has much room to be improved. A hybrid solar desalination process of the multi-effect humidification dehumidification and the basin-type unit should be no...

Energy Technology Data Exchange (ETDEWEB)

This compilation contains 50 ACRS reports submitted to the Commission, Executive Director for Operations, or to the Office of Nuclear Regulatory Research, during calendar year 1992. It also includes a report to the Congress on the NRC Safety Research Program. All reports have been made available to the public through the NRC Public Document Room and the US Library of Congress. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part I contains ACRS reports alphabetized by project name and by chronological order within project name. Part 2 categorizes the reports by the most appropriate generic subject area and by chronological order within subject area.

Energy Technology Data Exchange (ETDEWEB)

This compilation contains 41 Advisory Committee on Reactor Safeguards (ACRS) reports submitted to the Commission, Executive Director for Operations, or to the Office of Nuclear Regulatory Research, during calendar year 1991. It also includes a report to the Congress on the NRC Safety Research Program. All reports have been made available to the public through the NRC Public Document Room and the US Library of Congress. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by project name and by chronological order within project name. Part 2 categorizes the reports by the most appropriate generic subject area and by chronological order within subject area.

Energy Technology Data Exchange (ETDEWEB)

This compilation contains 54 ACRS reports submitted to the Commission or to the Executive Director for Operations during calendar year 1989. It also includes a report to the Congress on the NRC Safety Research Program. All reports have been made available to the public through the NRC Public Document Room and the US Library of Congress. The reports are divided into two groups: Part 1 -- ACRS Reports on Project Reviews, and Part 2 -- ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by project name and within project name by chronological order. Part 2 categorizes the reports by the most appropriate generic subject area and within subject area by chronological order.

Energy Technology Data Exchange (ETDEWEB)

This compilation contains 47 ACRS reports submitted to the Commission or to the Executive Director for Operations during calendar year 1987. It also includes a report to the Congress on the NRC Safety Research Program for FY 1988. All reports have been made available to the public through the NRC Public Document Room and the US Library of Congress. The reports are divided into two groups: Part 1: ACRS Reports on Project Reviews, and Part 2: ACRS Reports on Generic Subjects. Part 1 contains ACRS reports alphabetized by project name and within project name by chronological order. Part 2 categorizes the reports by the most appropriate generic subject area and within subject area by chronological order.

International Nuclear Information System (INIS)

The oxygen vacancies distribution in the rigid lattice and the thermally activated motion of oxygen atoms are studied in La1-xSrxGa1-xMgxO3-x (x=0.00; 0.05; 0.10; 0.15 and 0.20) compounds. For that 71Ga, 25Mg and 17O NMR was performed from 100 K up to 670 K, and ion conductivity measurements were carried out up to 1273 K. The comparison of the electric field gradients at the Ga- and Mg-sites evidences that oxygen vacancies appear exclusively near gallium cations as a species trapped below room temperature in local clusters, GaO5/2-#square#-GaO5/2. These clusters decay at higher temperature into mobile constituents of the structural octahedra Ga(O5/6#square#1/6)6/2. At the same time, the nearest octahedral oxygen environment of magnesium cations persists at different doping levels. The case of two adjacent vacant anion sites is found highly unlikely within the studied doping range. The thermally activated oxygen motion starts to develop above ...

International Nuclear Information System (INIS)

Full text: It is known that the ion implantation of germanium single crystals at room temperature results in drastic alteration of the germanium surface and the formation of cellular relief. Voids were found into the near-surface damage layer. The intersection of these voids with the germanium surface, as result of sputter etching, forms cellular relief. However, exact mechanism responsible for formation of the voids is not known. A 10 and 30 keV Ga"+ irradiation of Ge #left brace#100#right brace# crystal at room temperature was carried out using a focused ion beam (FIB) system with a dose in the range 0.5x10"1"2 to 1.5x10"1"4 ion/cm"2. The topology of the modified germanium surface and the structure of the radiation damage was studied using imaging facilities of the FIB systems and transmission electron microscopy. The strong cellular structure of Ge was observed after an ion dose of 3x10"1"3 ion/cm"2. High-resolution TEM showed a complex ...

Energy Technology Data Exchange (ETDEWEB)

The processing characteristics, tensile properties, and oxidation response of two Nb-Ti-Al-Cr alloys were investigated. One creep test at 650 C and 172 MPa was conducted on the base alloy, which contained 40Nb-40Ti-10Al-10Cr. A second alloy was modified with 0.11 at.% C and 0.07 at.% Y. Alloys were arc melted in a chamber backfilled with argon, drop cast into a water-cooled copper mold, and cold rolled to obtain a 0.8-mm sheet. The sheet was annealed at 1,100 C for 0.5 h. Longitudinal tensile specimens and oxidation specimens were obtained for both the base alloy and the modified alloy. Tensile properties were obtained for the base alloy at room temperature, 400, 600, 700, 800, 900, and 1,000 C and for the modified alloy at room temperature, 400, 600, 700, and 800 C. Oxidation tests the base alloy and modified alloy, as measured by weight change, were carried out at 600, 700, 800, and 900 C. Both the base alloy and the modified alloy were ...

International Nuclear Information System (INIS)

Protecting Earth and planets against the invasion of 'alien life forms' is not military science fiction, but it is the peaceful daily job of engineers and scientists of space agencies. 'Planetary Protection' is preventing microbial contamination of both the target planet and the Earth when sending robots on interplanetary space mission. It is important to preserve the 'natural' conditions of other planets and to not bring with robots 'earthly microbes' (forward contamination) when looking for 'spores of extra terrestrial life'. The Earth and its biosphere must be protected from potential extraterrestrial biological contamination when returning samples of other planets to the Earth (backward contamination). The NASA-Caltech Laboratory for Planetary Protection of Dr. Kasthuri Venkateswaran at the Jet Propulsion Laboratory (JPL) (California, USA) routinely monitors and characterizes the microbes of NASA spacecraft assembly rooms and space robots prior to flight. They ...

International Nuclear Information System (INIS)

The paper generalizes some results of the United States/Moldova program on advanced composite organic and semiconductor light emitters. High density exciton system bound to N impurity superlattice grown by modern technologies and GaP:N, GaP:N:Sm nanocrystals distributed in transparent fluorine-containing polymers will be used as the base elements for new generation of optoelectronic devices. The work seeks to expand further the applications of GaP itself through the formation of nanocomposites. Classic and new methods are applied for preparation of GaP:N nanoparticles with the controlled dimensions developed clear quantum confinement effect. The long-term ordered bulk GaP crystals as well as their nanoparticles have been investigated by TEM, XRD, Raman scattering, and luminescent methods. The evolution of the Raman Light Scattering and luminescence spectra is reported from pure and doped GaP single crystals grown over 40 years ago and evaluated approximately every 15 years. For the ...

Energy Technology Data Exchange (ETDEWEB)

Amorphous materials in the system xLi{sub 2}S{center_dot}(100-x)SiS{sub 2}, where x ranged from 50 to 70 mol %, and (100-y) (0.6Li{sub 2}S{center_dot}0.4SiS{sub 2}){center_dot}yLi{sub 4}SiO{sub 4}, where y ranged from 0 to 10 mol %, were synthesized by mechanical milling of crystalline starting materials, Li{sub 2}S, SiS{sub 2} and Li{sub 4}SiO{sub 4}. At the compositions with large amounts of Li{sup +} ions, a part of crystalline Li{sub 2}S used as a starting material remained in the milled powder samples. It was found that the milled powder samples in both systems obtained by mechanical milling exhibited high conductivities in the order of 10{sup -4}S{center_dot}cm{sup -1} at room temperature in spite of the presence of small amounts of Li{sub 2}S crystals. The conductivity values of the pelletized samples of xLi{sub 2}S{center_dot}(100-x)SiS{sub 2} powders maximized at the composition of about x=60. On the other hand, the conductivities in the composition range ...

Energy Technology Data Exchange (ETDEWEB)

Crystalline {alpha}-Fe{sub 2}O{sub 3} powder was prepared by the mechanical milling of crystalline {alpha}-FeOOH at room temperature in air. This result means that crystalline {alpha}-FeOOH is dehydrated by mechanical milling at room temperature. The obtained {alpha}-Fe{sub 2}O{sub 3} powder worked as a rechargeable electrode material in lithium ion conductive organic electrolytes. The electrodes exhibited high discharge capacities of over 1000mAhg{sup -1} corresponding to 6 Li per {alpha}-Fe{sub 2}O{sub 3} at potentials ranging from the open circuit potential to 0.5V (versus Li{sup +}/Li) in the first discharging (lithium insertion) process. This suggests that the valence deviation from Fe{sup 3+} in {alpha}-Fe{sub 2}O{sub 3} to Fe{sup 0} may be caused by electrochemical reduction. In contrast, after the first discharge, the electrodes exhibited high charge capacities of more than 700mAhg{sup -1} corresponding to 4.2 Li per {alpha}-Fe{sub ...

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) is a liquid-metal-cooled, fast neutron test reactor located on the Hanford Site. A dual computer system has been developed to monitor the reactor cover gas to detect and characterize any fuel or test pin fission gas releases. The system acquires gamma spectra data, identifies isotopes, calculates specific isotope and overall cover gas activity, presents control room alarms and displays, and records and prints data and analysis reports. The Fission Gas Monitor System (FGMS) integrates commercially available hardware and software, providing a reliable and easily maintained system. The design provides extensive automation of previous manual operations, reducing the need for operator training and minimizing the potential for operator error. The dual nature of the system allows either system A or B to be taken out of service for periodic tests or maintenance without interrupting the overall system performance. A control ...

Energy Technology Data Exchange (ETDEWEB)

The intermetallic phase NiAl is a potential material for high-temperature applications; however, its technical application was prevented so far by its high brittleness at room temperature. This problem may be solved by incorporating relatively high-ductility particles into the NiAl matrix. Controlled crack propagation experiments, tensile and pressure tests were carried out in order to analyze the toughness and deformation characteristics of NiAl composite materials containing niobium or molybdenum particles at room temperature and in ambient atmosphere. Both the niobium and the molybdenum particles increase the toughness as compared to the pure NiAl matrix, but no ductilisation was observed in the composite materials investigated. Model experiments in consideration of experimental data suggest, hovewer, that the toughness and ductility of NiAl may be enhanced by optimizing the microstructural and production parameters of the incorporated ...

Energy Technology Data Exchange (ETDEWEB)

This report discusses a representation scheme of device failures anticipated in nuclear power plant, to describe related knowledge in a computer software. Coping ability covering a wide range of physical events is desired in plant operators and maintenance staffs, but it is impractical to give them a set of experience to cover the all possible events in the education/training curriculum. However, in case that their knowledge of plant design and of generally-known physical principles are enforced, their ability of cause identification and of appropriate responding actions against inexperienced events are expected to be enhanced, by combining the basic engineering and physical knowledge. Most of the anomalies anticipated in nuclear power plants are initiated as an incipient failure in some auxiliary equipment initially affecting only within the relative subsystem and hiding from the central control room, and then are propagated to deviate process parameters in the ...

International Nuclear Information System (INIS)

The authors present the results of an investigation of the effect of gamma radiation on the properties of low-molecular moulded polymethyl methacrylates (molecular weight distribution, physicomechanical properties, resistance to the effects of aqueous media and physiological solution) in the form of copolymers of methyl methacrylate with methyl (MA) or butyl acrylate (BA) with the brand names Dacryl-4B, Dacryl-2M and Dacryl-4M (4% BA; 2 and 4% MA respectively) having a molecular weight of around 10"5. For comparison, block polymethyl methacrylate with a molecular weight of 3 x 10"6 was used. The results of experiments on the ageing of unirradiated and irradiated specimens in a heated store-room (t = 10 - 20"0C) and at high temperatures (90"0C) are also given. It is shown that irradiation with doses of 2.5-20 Mrad leads to radiolysis of the above copolymers, accompanied by destructive processes. Evidence of this is an increase in the polydispersity of the materials ...

Energy Technology Data Exchange (ETDEWEB)

High energy physics facilities must monitor the radiation doses received by their personnel. This monitoring can only be effective if the radiation detection devices can be calibrated with a good degree of accuracy. Radiation fields are usually composed of several types of radiation, including gamma rays, beta radiation, neutrons, etc. The neutron detection instruments respond not only to the neutrons coming directly from the source but also those scattered from the floor, walls, and ceiling. The amount of neutron scattering varies from site to site depending on the construction materials and layout of the building. The purpose of this study was to determine the scattered neutron fraction in the central volume of the calibration mezzanine of the Radiation Physics Calibration Facility (RPCF) at the Fermi National Accelerator Laboratory (Fermilab). At Fermilab, radiation workers dosimeters use CR39 for neutron detection, which are sent to an outside vendor for reading. As part of the ...

Energy Technology Data Exchange (ETDEWEB)

This is the final report of a three year DOE funded project titled ''A real-time coal content/ore grade (C{sub 2}OG) sensor''. The sensor, which is based on hyperspectral imaging technology, was designed to give a machine vision assay of ore or coal. Sensors were designed and built at Resonon, Inc., and then deployed at the Stillwater Mining Company core room in southcentral Montana for analyzing platinum/palladium ore and at the Montana Tech Spectroscopy Lab for analyzing coal and other materials. The Stillwater sensor imaged 91' of core and analyzed this data for surface sulfides which are considered to be pathfinder minerals for platinum/palladium at this mine. Our results indicate that the sensor could deliver a relative ore grade provided tool markings and iron oxidation were kept to a minimum. Coal, talc, and titanium sponge samples were also imaged and analyzed for content and grade with promising results. This ...

International Nuclear Information System (INIS)

Beta-21S is a new, metastable-beta titanium alloy which exhibits excellent oxidation resistance and mechanical properties at elevated temperatures. From a weld solidification standpoint, this alloy chemistry is of particular interest because its major beta-stabilizing elements (Mo and Nb) both exhibit equilibrium partitioning ratios (k_o) greater than unity, indicating their simultaneous partitioning during weld solidification to the initial solid to form (i.e., dendrite cores), and correspondingly their depletion in the final regions of solidification (i.e., dendrite interstices). Such elemental partitioning, if retained down to room temperature, may be expected to promote local variations in the postweld aging response. The objectives of the present investigation were to characterize Gas Tungsten-Arc weld solidification and HAZ liquation phenomena in Beta-21S and to examine the influence of residual microsegregation in the weld zone on alpha precipitation during ...

Energy Technology Data Exchange (ETDEWEB)

Step-scan Fourier transform infrared spectroscopy in conjunction with impulse stress on polymer films has been used to monitor dynamic rheological responses in real time. A novel piezo-electrically-driven polymer microrheometer was employed to apply repetitive impulses to the polymer sample while time-domain spectra were recorded. Recent results include the study of both semi-crystalline polymers such as isotactic polypropylene (iPP) and elastomers such as Estane polyester/polyurethane copolymer and Kraton tri-block copolymer. The spectral changes of iPP are consistent with frequency-domain results. For iPP at room temperature, large differences in the response times of different absorption bands are not seen. However, the orientation response of the CH{sub 3} rocking mode is slightly slower than the responses of the backbone modes. To the authors` knowledge, this is the first reported successful step-scan FTIR time-domain dynamic polymer opto-rheology experiment. ...

Energy Technology Data Exchange (ETDEWEB)

The important amount of hydration water in the ulexite (NaCaN{sub 5}O{sub 9}.8H{sub 2}O), allows using calcination methods to increase its B{sub 2}O{sub 3} content. This paper analyses the thermal decomposition reaction of a preconcentrated ulexite through weight loss measurements, which occur during the heating of samples until 1000 degree centigree, Determinations of heat content at each temperature were made using an isoperibol calorimeter. The mean specific heat was calculated from these values, and its dependence on temperature was determined. The maximum weight loss was about 32.5% and the specific heat obtained was 1,13 kJ/kg 0 C for solid samples and 1,38 kJ/kg''0 C for fluid samples. The results are useful for the design of the industrial process, in order to determine the thermal requirements for heating calcined ulexite, and to obtain smelted ulexite. (Author) 19 refs.

Energy Technology Data Exchange (ETDEWEB)

We tried to apply a quartz crystal as a sensor by using the resonant frequency and the resistance properties of quartz crystals. Four kinds of fatty acids that have the same head groups were coated on the surfaces of the quartz crystals, and the shift of the resonant frequency and the resistance were observed based on the lengths of the tail groups. Myristic acid (C{sub 14}), palmitic acid (C{sub 16}), stearic acid (C{sub 18}), and arachidic acid (C{sub 20}) were deposited on the surfaces of quartz crystals by using the Langmuir-Blodgett (LB) method. As a result, the resonant frequency change was more sensitive to high molecular-weight fatty acids than to low molecular-weight ones. We also observed the effect of temperature on stearic acid LB films, and the response properties of quartz crystals coated with stearic-acid LB films to organic gases were investigated. As a result, the sensitivity of quartz crystals to organic gases was higher for higher molecular-weight gas, and we found ...

Energy Technology Data Exchange (ETDEWEB)

Vaarst Vestervang (Denmark) comprises 16 villas and 1 communal building. The complex was designed by the inhabitants themselves with the aim of polluting the environment as little as possible. The land area constitutes 69.000 square meters where it is possible to grass animals. The document reports a measuring programme concerning the overall heat consumption as one of the main aims of the inhabitants is to save energy and thus contribute to the protection of the environment. The capacity of the solar collectors predominantly used in the building complex was 235 kWh/m{sup 2}. Supplementary heating is provided by boilers fired with wood. The measuring system is described in detail. Tables show the influence of heat transmission losses, ventilation, airing out of rooms, the angle of the sun`s rays within the buildings and heating needs on energy consumption. Energy consumption data is presented in relation to the forms of space and water heating utilized. Daily ...

Energy Technology Data Exchange (ETDEWEB)

The RADionuclide Transport, Removal, And Dose (RADTRAD) code is designed for US Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the offsite population and to control room operators following a design-basis accident at Light Water Reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465, ``Accident Source Terms for Light-Water Nuclear Power Plants.`` The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different removal mechanisms that use, as input, ...

Energy Technology Data Exchange (ETDEWEB)

This is Volume 3 in a series of documents on energy efficiency of consumer products. This volume discusses energy efficiency of water heaters. Water heaters are defined by NAECA as products that utilize oil, gas, or electricity to heat potable water for use outside the heater upon demand. These are major appliances, which use a large portion (18% on average) of total energy consumed per household (1). They differ from most other appliances in that they are usually installed in obscure locations as part of the plumbing and are ignored until they fail. Residential water heaters are capable of heating water up to 180{degrees}F, although the setpoints are usually set lower.

International Nuclear Information System (INIS)

Thallium-201 diethyldithiocarbamate (DDC) behaves like a chemical microsphere and is trapped by spontaneous decomposition in the brain in proportion to regional perfusion. They have shown that the technetium-99m analog, Tc-99m DDC (1), is unsuitable for cerebral perfusion imaging because it does not decompose rapidly enough to be trapped in the brain. With the goal of turning this greater stability of 1 into an advantage, a series of dithiocarbamates with lipophilic or amine groups designed to enhance cerebral uptake and retention was prepared from the following amines by reaction with carbon disulfide and sodium hydroxide: pyrrolidine (2), piperazine (3), 4-benzylpiperazine (4), and 4-(1-piperidino)piperidine (5). These ligands (5 mg) were labelled with Tc-99m in > 95% efficiency (ITLC-SG, saline) by reduction of pertechnetate at room temperature with formamidine sulfinic acid at alkaline pH. In preliminary studies, 4 and 5 show a trend of increasing oil/buffer ...

International Nuclear Information System (INIS)

An alloy of composition Ti-4.4 wt.% Ta-1.9 wt.% Nb is being developed as a structural material for corrosion applications, as titanium and its alloys possess excellent corrosion resistance in many oxidizing media. The primary physical metallurgy database for the Ti-4.4 wt.% Ta-1.9 wt.% Nb alloy is being presented for the first time. Determination of the #beta# transus, M_s temperature and classification of the alloy have been carried out, employing a variety of microscopy techniques, X-ray diffraction (XRD), micro-hardness and differential scanning calorimetry (DSC). The #beta# transition temperature or #beta# transus determined using different experimental techniques was found to agree very well with evaluations based on empirical calculations. Based on chemistry and observed room temperature microstructure, the alloy has been classified as an #alpha# + #beta# titanium alloy. The high temperature #beta# transforms to either #alpha#' or #alpha# + #beta# by a ...

Energy Technology Data Exchange (ETDEWEB)

Standard Leadframes used in surface mount technology are finished with a layer of eutectic SnPb for passivation and for enhancing solder wetting during reflow. When eutectic SnPb is replaced by Pb-free solder, especially the eutectic SnCu, a large number of Sn whiskers are found on the Pb-free finish. Some of the whiskers are long enough to become shorts between the neighboring legs of the leadframe. How to suppress their growth and how to perform accelerated test of Sn whisker growth are crucial reliability issues in the electronic packaging industry. In this paper, we report the study of spontaneous Sn whisker growth at room temperature on eutectic SnCu and pure Sn finishes. Both compressive stress and surface oxide on Sn are necessary conditions for whisker growth. Structure and stress analyses by using the micro-diffraction in synchrotron radiation are reported. Cross-sectional electron microscopy, with samples prepared by focused ion beam, are included.

International Nuclear Information System (INIS)

Glasses in the system (95-x) [0.25 Na2O-0.75 B2O3]-x P2O5-5 Fe2O3 (0?x?15 mol%), have been prepared by the melt quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of P2O5 on the structure of the glass system. Elastic properties Poisson's ratio, micro-hardness and Debye temperature have been investigated using sound wave velocity measurements at 4 MHz (both longitudinal and shear) at room temperature. The results showed that the density and the molar volume increase as both sound velocities and the determined glass transition temperatures decrease with increasing the contents of P2O5. Infrared spectra of the glasses reveal that the borate network consists of diborate units and is affected by the increase in the concentration of P2O5 content as a second network former. These results are interpreted in terms of the replacement of the diborate units with B-O-B bridges by phosphate units with non-bridging oxygens ...

International Nuclear Information System (INIS)

In this work we present the electrical characterization of non self-aligned p-channel thin film transistors fabricated by using laser doping technique for source/drain contact formation and gate oxide deposited at room temperature by Electron Cyclotron Resonance Plasma Enhanced Chemical Vapour Deposition. These techniques are suitable for a very low temperature process for TFT fabrication. The output characteristics show a current increase at high drain voltage ('kink' effect) rather moderate, if compared to self aligned polysilicon TFTs, probably due to the gradual doping profile induced by laser doping process. After bias stress at low gate voltage and high drain voltage condition a strong reduction of kink current has been observed in the output characteristics at high drain voltage, whereas minor changes has been observed in the transfer characteristics. This behaviour is similar to what observed in n-channel Gate Overlapped Thin Film Transistors. In the high ...

Energy Technology Data Exchange (ETDEWEB)

The spectroscopic properties of Eu{sup 3+} doped into two lanthanum chlorotungstates matrices, namely LaWO{sub 4}Cl (1-1) and La{sub 3}WO{sub 6}Cl{sub 3}(3-1), are investigated. The fluorescence spectra of these compounds, recorded at room and liquid nitrogen temperatures, show that the lanthanide ion occupies only one site with the low symmetry, C{sub s}, in both cases. From the energy level schemes of the {sup 7}F{sub J} levels (J = 0, 1, 2, 3, 4, 5), two sets of crystal field parameters (cfp) are deduced, in a C{sub 2v} approximated point symmetry (i.e., 9 cfp), simulating the experimental data, correctly. Furthermore, for the 3-1 compound, the data is complete enough to extend the calculations to the real point group, C{sub s} (14 cfp).

International Nuclear Information System (INIS)

Sodium silicate is vacuum impregnated in bauxite waste (red mud) at room temperature to develop ceramics of mechanical properties comparable to the sintered ceramics. For a concentration up to 10% the fracture toughness increases from 0.12 MNm"-"3"/"2 to 0.9 MNm"-"3"/"2, and the compressive strength from 7 MNm"-"2 to 30 MNm"-"2. The mechanical properties do not deteriorate, when soaked in water for an entire week. The viscosity and the concentration of the silicate solution are crucial, both for the success of the fabrication and the economics of the process. Similar successful results have been obtained for bauxite and lime stone, even though the latter has poor weathering properties. With scanning electron microscopy and energy dispersive analysis, an attempt is made to identify the crystals formed in the composite, which are responsible for the strength. The process is an economic alternative to the sintered ceramics in the construction industry in the tropical ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the safety gas management system utilizing public telephone cables. Buyo Gas Co., Ltd. has installed about 100 governors for exclusive-use or use in the districts to control the gas supply to the consumers. A gas safety management system has been developed. This system consists of a pressure sensor, the terminals of gas leak alarms, and their masters. The features lie in that the system can utilize public cables, is operative at interruption of power service, can correspond to emergency situations, serves to save the cost, and can display the data constantly. For electric facilities in a governor room and the NTT cable service work, sufficient agreement with the possessor is required. In the case of non-utility electric facilities, some restrictions are imposed on the cable work for laying from privately-owned transformers, etc. Insurance for the facilities is necessary to prepare for lightning accidents. This system realizes the pipe pressure ...

International Nuclear Information System (INIS)

Highly conductive biaxially textured RuO_2 thin films were deposited on technically important SiO_2/Si substrates by pulsed laser deposition, where yttria-stabilized zirconia (YSZ) produced by ion-beam-assisted-deposition (IBAD) was used as a template to enhance the biaxial texture of RuO_2 on SiO_2/Si. The biaxially oriented RuO_2 had a room-temperature resistivity of 37 #mu##OMEGA#-cm and residual resistivity ratio above 2. We then deposited Ba_0_._5Sr_0_._5TiO_3 thin films on RuO_2/IBAD-YSZ/SiO_2/Si. The Ba_0_._5Sr_0_._5TiO_3 had a pure (111) orientation normal to the substrate surface and a dielectric constant above 360 at 100 kHz. copyright 1998 Materials Research Society.

Energy Technology Data Exchange (ETDEWEB)

Various nylons including nylon 6, nylon 66, nylon 610 and nylon 12 in the forms of fiber and film were irradiated with the gamma-ray from Co-60 at the dose rate of 0.12 Mrad/hr in the atmosphere of oxygen at 7 kg/cm/sup 2/ and at the room temperature. The irradiation in vacuum on the same specimens was performed at 0.5 Mrad/hr. The tensile properties and the gel fraction of the irradiated nylon samples were measured, and the radiation resistance of the nylons against the irradiation at low dose rate was estimated. From the experimental results, it became clear that in the case of irradiation in vacuum, all the nylons were durable to the irradiation of 250 Mrad or more, and nylon 6 was more durable than nylon 12, and in the case of irradiation in pressurized oxygen, the radiation resistance of the nylons decreased to one-tenth as compared with that in vacuum, and contrary to that in vacuum, nylon 12 was superior to nylon 6, while nylon 610 was intermediate. From ...

CERN Document Server

We consider the role of quantum effects in the transfer of hyrogen-like species in enzyme-catalysed reactions. This study is stimulated by claims that the observed magnitude and temperature dependence of kinetic isotope effects imply that quantum tunneling below the energy barrier associated with the transition state significantly enhances the reaction rate in many enzymes. We use a path integral approach which provides a general framework to understand tunneling in a quantum system which interacts with an environment at non-zero temperature. Here the quantum system is the active site of the enzyme and the environment is the surrounding protein and water. Tunneling well below the barrier only occurs for temperatures less than a temperature $T_0$ which is determined by the curvature of potential energy surface near the top of the barrier. We argue that for most enzymes this temperature is less than room temperature. For physically reasonable parameters quantum ...

Energy Technology Data Exchange (ETDEWEB)

A new rapid solidification process machine will be able to produce eight-inch diameter by six-inch thick finished cavities at the rate of one per hour - a rate that will change the tooling industry dramatically. Global Metal Technologies, Inc. (GMTI) (Solon, OH) has signed an exclusive license with Idaho National Engineered and Environmental Laboratories (INEEL) (Idaho Falls, ID) for the development and commercialization of the rapid solidification process (RSP tooling). The first production machine is scheduled for delivery in July 2001. The RSP tooling process is a method of producing production level tooling in prototype timing. The process' inventor, Kevin McHugh, describes it as a rapid solidification method, which differentiates it from the standard spray forming methods. RSP itself is relatively straightforward. Molten metal is sprayed against the ceramic pattern, replicating the pattern's contours, surface texture and details. After spraying, the molten tool ...